Dc lab Manual

LIST OF EXPERIMENTS

DIGITAL COMMUNICATION LAB

S.No. NAME OF EXPERIMENTS EXPERIMENT NO.

1. To Study of Pulse Amplitude Modulation and Time

division multiplexing.

ECE-DC-EX-01

2. To study Pulse Time Modulation and De

Modulation(PWM and PPM ).

ECE- DC-EX-02

3. Study the Analog to Digital conversion and Digital to

Analog conversion.

ECE- DC-EX-03

4. Study of Delta Modulation and Demodulation ECE- DC-EX-04

5. Study of Adaptive Delta Modulation and Demodulation. ECE- DC-EX-05

6. Study of Amplitude Shift Keying. ECE- DC-EX-06

7. Study of Frequency Shift Keying. ECE-DC-EX-07

8. Study of Phase Shift Keying. ECE- DC-EX-08

9. To Study Quadrature Phase Shift Keying transmission

and Reception.

ECE- DC-EX-09

10. ECE- DC-EX-10

Experiment No-1

Aim: To Study of Pulse Amplitude Modulation and Time division multiplexing.

Apparatus Required:-ST-2110 kit with power supply cord CRO with connecting probe,

connecting cords.

Theory: Most digital modulation systems are based on pulse modulation. It involves variation

of a pulse parameter in accordance with the instantaneous value of the information signal. This

parameter can be amplitude, width, repetitive frequency etc. Depending upon the nature of

parameter varied, various modulation systems are used. Pulse amplitude modulation, pulse width

modulation, pulse code modulation are few modulation systems cropping up from the pulse

modulation technique. In pulse amplitude modulation (PAM) the amplitude of the pulses are

varied in accordance with the modulating signal. In true sense, pulse amplitude modulation is

analog in nature but it forms the basis of most digital communication and modulation systems.

The pulse modulation systems require analog information to be sampled at predetermined

intervals of time. Sampling is a process of taking the instantaneous value of the analog

information at a predetermined time interval. A sampled signal consists of a train of pulses,

where each pulse corresponds to the amplitude of the signal at the corresponding sampling time.

The signal sent to line is modulated in amplitude and hence the name Pulse Amplitude

Modulation (PAM).

Block diagram:

(Pulse Amplitude Modulation)

WAVE FORM :

Time Division Multiplexing:

Time division multiplexing is the process of combining the samples from different information

signals, in time domain so that they can be transmitted over the common channel. The fact

utilized in TDM technique is that there are large intervals between the message samples. The

samples from the other sources can be placed within these time intervals. Thus every sample is

separated from other in time domain. The time division multiplexing system can be simulated by

two rotating switches, one at transmitter and the other at receiver. (See figure 7) The two wipers

rotate and establish electrical contact with one channel at a time.

(Principle operation of TDM)

Each signal is sampled over one sampling interval and transmitted one after the other

along a common channel. Thus part of message 1 is transmitted first followed by part

of message 2, message 3 and then again message 1 so on. The switches connect the transmitter

and the receiver to each of the channels in turn for a specific interval of time. In effect each

channel is sampled and the sample is transmitted When the switches are in the channel 1

position, channel 1 forms a PAM channel with an LPF for reconstruction, and so on for channels

2 and 3. The result is that the amplitudes samples from each channel share the line sequentially,

becoming interleaved to form a complex PAM wave, as shown above. A major problem in any

TDM system is the synchronization of the transmitter and receiver timing circuits. The

transmitter and receiver must switch at the same time and frequency. Also SW1 must be in the

channel 1 position when SW2 is in the channel 1 position, so that the switches must be

synchronized in position also. In a system that uses analogue modulation (PAM) the time slots

are separated by guard slots to prevent crosstalk between channels.

WAVE FORM :

(Timing waveform of TDM-PAM system)

Procedure:

1. Connect the circuit as shown in Figure 1.1.

a. Output of sine wave to modulation signal input in PAM block keeping the switch in 1 KHz

position.

b. 8 KHz pulse output to pulse input.

2. Switch ‘On’ the power supply & oscilloscope.

3. Observe the outputs at TP(3 & 5) these are natural & flat top outputs respectively.

4. Observe the difference between the two outputs.

5. Vary the amplitude potentiometer and frequency change over switch & observe the effect on

the two outputs.

6. Vary the frequency of pulse, by connecting the pulse input to the 4 frequencies available i.e. 8,

16, 32, 64 kHz in Pulse output block.

7. Switch ‘On’ fault No. 1, 2, 3, 4 one by one & observe their effect on Pulse Amplitude

Modulation output and try to locate them.

8. Switch ‘Off’ the power supply.

RESULT: The Study of Pulse Amplitude Modulation and Time division multiplexing

successfully .

Experiment No-2

Aim:To study Pulse Time Modulation and De Modulation(PWM and PPM ).

Apparatus Required: ST-2110 Kit, power supply cord, CRO with connecting probe,

Connecting cor

BLOCK DIAGRAM:

Theory: The PWM is a technique which is used to drive the inertial loads since a very long

time.The simple example of an inertial load is a motor. Apply the power to a motor for a very

short period of time and then turn off the power: it can be observed that the motor is still running

even after the power has been cut off from it. This is due to the inertia of the motor and the

significance of this factor is that the continuous power is not required for that kind of devices to

operate. A burst power can save the total power supplied to the load while achieving the same

performance from the device as it runs on continuous power.

The PWM technique is use in devices like DC motors, Loudspeakers, Class -D

Amplifiers, SMPS etc. They are also used in communication field as-well. The modulation

techniques like AM, FM are widely used RF communication whereas the PWM is modulation

technique is mostly used in Optical Fiber Communication (OFC).

As in the case of the inertial loads mentioned previously, the PWM in a communication link

greatly saves the transmitter power. The immunity of the PWM transmission against the inter-

symbol interference is another advantage. This article discusses the technique of generating a

PWM wave corresponding to a modulating sine wave.

WAVE FORM :

Procedure:

1. Connect the circuit as shown in Figure 7.1 and also described below for clarity.

a. 1 KHz sine wave output of function generator block to modulation input

of PWM block.

b. 64 KHz square wave output to pulse input of PWM block.

2. Switch ‘On’ the power supply & oscilloscope.

3. Observe the output of PWM block.

4. Vary the amplitude of sine wave and see its effect on pulse output.

5. Vary the sine wave frequency by switching the frequency selector switch to 2

KHz.

6. Also, change the frequency of the pulse by connecting the pulse input to

different pulse frequencies viz. 8 KHz, 16 KHz, 32 KHz and see the variations

in the PWM output.

7. Switch ‘On’ fault No. 1, 2, & 5 one by one & observes their effect on PWM

output and tries to locate them.

8. Switch ‘Off’ the power supply.

Experiment No 3

AIM: Study the Analog to Digital conversion and Digital to Analog conversion.

APPRATUS:

THEORY: A/D Conversion

The PCM Transmitter samples the analog input, time division multiplex and many

such channels, quantizes it & code it by analog to digital conversion. As it is known,

the binary number system consists of binary digits '0' and '1'. The group of n bits is

called as word and is used to distinguish one code from the other. The range of

decimal numbers represented by such n bits code is equal to 2n (including 0) e.g. If we

take an 8 bit word, the number or different codes possible is equal to 28

= 256 i.e. we

have 0 to 255 code levels available

This range can be used to indicate any range of voltage. The process of allocating the

binary values to each sample taken in PAM system is known as quantization. Every

binary number indicates one level. Since binary value changes in discrete steps & is

not continuous like analog waveform, some distortion creeps in at the time of value

assignment; this is discussed in forth coming parts. The range of binary values used is

the design feature of the system & depends upon the amplitude range of the signal and

the accuracy of the conversion to be achieved.

Most systems use an 8 bit word length which is practically found most suitable to

cover the sufficient range & provide the accuracy needed for speech signals. As with

all engineering processes, quantization produces its own problems & an engineering

compromise is then called for. The two major problems associated with quantization

are : 1) One major problem associated with quantization is due to the discrete nature of

binary numbers which are used to represent continuously variable analog

waveform, It is not possible to represent all the analog values (which are infinite

in number) by limited binary words e.g. if in the figure 27, the analog value lies in

between the two voltages represented by 0011 & 0100 binary words, what will

happen?

In such cases the system allocates a binary number closest to the sample value. This leads to distortion of the information signal & the approximation is random for different voltage levels. Hence it is known as quantization noise. Quantization noise can be reduced by increasing the number of bits used to represent a sample. But it can never be eliminated. Increasing the number of bits in a word has an effect of increasing the number of quantization levels. A digital-to-analog converter, or simply DAC, is a semiconductor device that is used to convert a

digital code into an analog signal. Digital-to-analog conversion is the primary means by which digital

equipment such as computer-based systems are able to translate digital data into real-world signals

that are more understandable to or useable by humans, such as music, speech, pictures, video, and the

like. It also allows digital control of machines, equipment, household appliances, and the like. A

typical digital-to-analog converter outputs an analog signal, which is usually voltage or current that is

proportional to the value of the digital code provided to its inputs. Most DAC's have several digital

input pins to receive all the bits of its input digital code in parallel (at the same time). Some DAC's,

however, are designed to receive the input digital data in serial form (one bit at a time), so these only

have a single digital input pin. A simple DAC may be implemented using an op-amp circuit known as

a summer, so named because its output voltage is the sum of its input voltages. Each of its inputs

uses a resistor of different binary weight,

such that if R0=R, then R1=R/2, R2=R/4, R3=R/8,.., RN-1=R/(2N-1). The output of a summer circuit

with N bits is:

Vo = -VR (Rf / R) (SN-12N-1 + SN-22N-2+...+S020)Where VR is the voltage to which the bit is connected when the digital input is '1'. A= digital input is '0' if the bit is connected to 0V (ground).

(An Op Amp Summer Circuit Used as a DAC)

Digital Transmission:-There are two methods for sending digital data over a distance, namelya. Parallel transmissionb. Serial transmissionIn short distance communication like inside terminal equipment or two computerterminals located near each other, the signals are passed in parallel, format overparallel wires. Thus the signal in the form of a word is passed. This mode is faster.For long distances, even more than few feet’s, this is uneconomical & inefficient wayof transmission. It is a wasteful of transmission media as each bit requires a separatelink. Therefore the digital signals are transmitted serially over a single link.The two important parameters in serial signaling are1. The modulation rate or the signaling rate (in Baud)&2. data transmission rate or bit rate (in Bits per second)The signaling rate or modulation rate is defined as the maximum rate at which thesignal is switched between signaling rate (or number of symbols transmitted persecond).The other way of defining modulation rate is that it is the reciprocal of the shortesttime for which the signal remains in any state. The modulation rate is measured inBaud which is equal to one unit signal element per second.

Experiment no 4

AIM: Study of Delta Modulation and Demodulation

APPRATUS: ST-2105 kit with power supply cord CRO with connecting probe, connecting

cords.

Theory of Delta Modulation:

As it has been seen, delta modulation system is unable to chase the rapidly changing information

of the analog signal, which gives rise to distortion & hence poor quality reception. This is known

as slope overloading phenomenon. The problem can be overcome by increasing the integrator

gain (i.e. step-size). But using high step-size integrator would lead to a high quantization noise.

Quantization Noise :

It is defined as error introduced between the original signal, & the quantized signal due to the

fixed step size in which the signal (quantized) is incremented. As the error is random in nature &

hence unpredictable, it can be treated as noise. High quantization noise may play havoc on small

amplitude signals. The solution to this problem is to increase the integrator gain for fast-changing

input & to use normal gain for small amplitude signals. The basic idea is to increase the

integrator the integrator gain (it is doubled on this trainer) when slope overload occurs. If still it

is unable to catch up with the signal, the integrator gain is doubled again. The integrator on board

has four available gains standard, standard X2, standard X4, and standard X8. The integrator thus

adopts it self to the gain where its lowest value can just overcome the slope overloading effect.

See figure 8. 10. As it can be observed, the adaptive delta modulator is similar to the delta

modulator except for few blocks namely the counter & the control circuit. The input to the

control circuit is the latched data from the D Flip-Flop. The counter is reset whenever 'high'

appears at the output of the control circuit. Both the counter & the control circuit are clocked by

the same TX clock. The input to the integrator from the counter is a two-bit control word, which

controls the gain of the integrator. When the output of counter is '00' the gain is lowest (standard)

where as it is highest (standard X8) for counters output '11'. The Control Circuit Works as

Follows :

The control circuit compares the preset data bit from D flip-flop with the previous two data bits.

Its output to the counter is high when the three bits are identical, the control circuits output goes

low, thus letting the counter advance with every clock cycle. This advancement continues till the

output from the control circuit does not go 'high'. Each time the counter is incremented from ‘00’

integrator gain is doubled till the counter reached '11' where it remains in that state until it is reset

by the counter. Similarly, the adaptive delta demodulator is a like delta demodulator except for

two blocks namely, the control circuit & the counter. They function in the same way as in

modulator part, except for the fact that they are clocked by the receiver clock.

BLOCK DIAGRAM:

DIAGRAM:

(Delta Modulation)

Procedure:Initial setup of ST2155:Clock frequency selector switches : A = 0 and B = 0 position. Integrator (1) blocks switches position: Gain control switch position : Left-hand side.Switches position : A=0 and B=0 position.Integrator (2) blocks switches position:Gain control switch position :Right-hand sideSwitches position : A = 0 and B = 0 position.1. Connect the mains supply cord to the Trainer.2. Make connection on the board as shown in the figure 1.1.3. Switch 'ON' the trainer power supply and oscilloscope.4. In order to ensure for correct operation of the system, we first take the input to 0V. So connect the '+' input of the delta modulator's voltage comparator to 0V and monitor on an oscilloscope the output of integrator 1 (TP13) and the output of the transmitter's unipolar to bipolar converter (TP 29) If the transmitter's unipolar to bipolar converter output has equal positive and negative output levels, integrator’s output will be a triangular wave centered around '0' Volts, as shown in figure 1.2 (Case A). However, if the unipolar to bipolar converter’s negative level is greater than the positive level, the integrator's output will appear as shown in figure 1.2 (Case B). Should theunipolar to bipolar converter’s positive output level be the greater of the two levels, the integrator's output will resemble that shown in figure 1.2 (Case C).5. The relative amplitudes of the unipolar to bipolar converter’s positive and negative output levels can be varied by adjusting the level adjust preset in the unipolar to bipolar converter circuit 1 block. When it is turned anticlockwise, the negative level increases relative to the positive level, when turned clockwise, the positive level increases relative to the negative level.

Case A: Bipolar output: Positive level = Negative level

Case B: Bipolar output: Positive level < Negative level

Case C: Bipolar output: Positive level > Negative level6. Adjust the transmitter's level changer preset until the output of integrator 1 (TP 13) is a triangular wave centered around 0 Volts, as shown in figure 1.2 (Case A). The peak-to-peak amplitude of the triangle wave at the integrator's output should be 1.8V (approx), this amplitude is known as the integrator step size. The output from the transmitter's bistable circuit (TP 19) will now be a stream of alternate '1' and '0', ‘s' this is also the output of the delta modulator it self. The delta modulator is now said to be 'balanced' for correct operation.7. Examine the signal at the output of integrator 2 (TP 41) at the receiver. This should be a triangular wave, with step size equal to that of integrator 1, and ideally centre around 0 Volts. If there is any DC bias at the output of integrator 2, remove it by adjusting the receiver's level adjust preset (in the unipolar to bipolar converter circuit 2 block). This preset adjusts the relative amplitudes, of the positive and negative output levels from the receiver's unipolar to bipolar converter circuit. Only when these levels are balanced will there be no offset at the output of integrator2.8. Outputs at TP 13 and TP 41 respectively Volts/Div: 1V Clock Frequency: 50 KHz Time/Div: 20 usec Input Signal : 0VWAVE FORM :

The receiver's low pass filter (whose cut off frequency is 4.2 KHz.) then filters out the higher - frequency triangular wave, to leave a DC level at the output of filter (TP 43). If the receiver's

level adjust preset has been adjusted correctly, this DC level will be '0' volt. The delta demodulator also is now balanced for correct operation.

9. Disconnect the voltage comparators '+' input from 0V, and reconnect it to the ~1 KHz output from the function generator block; the modulator's analog input signal is now a 1 KHz sine wave. Monitor this analog signal at the voltage comparator's '+' input (TP 15) together with the output of, integrator 1 (TP 13).Trigger the scope on the same analog signal which is applied to the

voltage comparator's '+' input (TP 15). Note how the output of the transmitter integrator follows the analog input, as was illustrated in figure 1.10. Display the data of the transmitter's bistable (at TP 19), together with the analog input at TP 15 (again trigger on this signal), and note that the 1 KHz sine wave has effectively been encoded into a stream of data bits at the bistable's output, ready for transmission to the receiver.11. For a full understanding of how the delta modulator works, examine the output of the voltage comparator (TP 16), the bistable's clock input (TP 19), and the unipolar to bipolar output (TP 29)12. Outputs at TP 13 and TP 41 respectively Volts/Div: 5V Clock Frequency: 50 KHz Time/Div: 500usec Input Signal : 1 KHz, 10VppWAVE FORM :

Display the output of integrator 1 (TP 13) and that of integrator 2 (TP 41) on thescope. Note that the two signals are very similar in appearance, showing that the demodulator is working as expected. 13. Display the output of integrator 2 (TP 41) together with the output of the receiver's low pass filter block (TP43). Note that although the integrator’s output has been smoothed out somewhat by the low pass filter, some unwanted 'ripple' still remains at filter's output This 'ripple' is due to the 'quantization noise' at the integrator's output, which is caused by the relatively large integrator step size. This step size can be reduced by increasing the rate at which the system is clocked (i.e. the sampling frequency).This reduces the sampling period, and hence the time available between samples for the integrators to ramp up and down.14. The current system clock frequency is 50 KHz. This is set by the A, B switches in the clock frequency selector block, which are currently in the A= 0, B= 0 positions. While monitoring the same signals, increase the system clock frequency to 100 KHz, by putting the switches in the A = 0, B = 1 positions..15. By changing the system clock frequency to first 200 KHz (clock frequency selector switches in A=l, B=0 positions), and then to 400 KHz (switches in A=l, B=1 positions), note the improvement in the low - pass filter's output signal (TP43). Once again, it may be necessary to adjust slightly the transmitter's level adjust preset, in order to obtain a stable oscilloscope trace.16. Using a system clock frequency of 400 KHz compare the low pass filter's output (TP43) with the original analog input (TP15). Output waveforms at TP13 and TP43 respectively Volts/Div: 5V Clock Frequency: 400 KHz Time/Div: 500usec Input Signal frequency: 1 KHz, 10Vpp

WAVE FORM :

There should now be no noticeable difference between them, other than a slight delay.17. While continuing to monitor the transmitter's analog input (TP15) and the receiver's low-pass filter output (TP43), disconnect the comparator's + input from the 1 KHz sine wave output, and reconnect it to 2 KHz, 3 KHz and 4 KHz outputs in turn and using system clock frequency of 50 KHz . Note that, as the frequency of the analog signal increases, the low pass filter's output becomes more distorted and reduced in amplitude.18. In order to understand what has caused this distortion, leave the comparator's + input connected to the 4 KHz sine wave output of the function generator, and examine the output of integrator 2 (TP41). Note that the integrator's output no longer approximates the analog input signal, but is triangular. Compare this with the output of integrator 1 (TP13), and note that the two signals are exactly the same; the problem obviously starts in the delta modulator circuit

Output waveforms at TP13 and TP43 respectively Volts/Div: 5V Clock Frequency: 400 KHz Time/Div: 200usec Input Signal frequency: 4 KHz, 10VppWAVE FORM :

Slope Overloading

19. Compare the 4 KHz analog input signal (TP15) with the output of integrator 1 (TP13) it should now become clear what has happened. The analog signal is now changing so quickly that the integrator's output cannot ramp fast enough to 'catch up' with it, and the result is known as 'slope overloading.'20. Although the system clock frequency i.e. the sampling frequency determines how often the integrator's output direction can change (up or down), it does not affect how quickly the integrator's output can ramp up and down. Consequently, changing the system clock frequency will not help the slope overload problem. Prove this by changing the clock frequency selector switches, and noting that the problem is still present.Return the switches to the A= 1, B=1 (400 KHz clock frequency) position before continuing.

21. If slope overloading is to be avoided in a practical delta modulation system, thetransmitter integrator must be able to ramp up or down at a rate which is at leastas great as the maximum rate of change at the transmitter's analog input. If theincoming analog signal is a sine wave, its maximum rate of change occurs at thezero crossing point, and is proportional to both the frequency and the amplitudeof the sine wave. the output of integrator 1 (TP17) and the output of the transmitter's level changer (TP15) If the transmitter's level changer output has equal positive and negative output levels. Integrator’s output will be a triangle wave centered around '0' Volts, as shown in figure 6 (Case A). However, if the level changer's negative level is greater than the positive level, the integrator's output will appear as shown in figure 6 (Case B). Should the level changer's positive output level be the greater of the two levels, the integrator's output will resemble that shown in figure 6 (Case C).

Result: The Delta modulation / demodulation and Slope Overloading effect has been studied.

Experiment no-5

AIM: Study of Adaptive Delta Modulation and Demodulation.

APPRATUS: ST-2105 kit with power supply cord CRO with connecting probe, connecting

cords.

THEORY: Theory of Adaptive Delta Modulation

The delta modulation & adaptive delta modulation suffers from two serious limitations, namely,

1. They are not able to pass DC level information, which is a must in video systems.

2. The signal to noise ratio decreases as the signal frequency increases. Both these serious

limitations can be overcame by delta sigma modulation. The delta modulator on-board can pass

DC level information if the integrators are zeroed before hand (by level adjust presets) & the

gains of integrator at two ends (TX & RX) are exactly equal. This is possible on ST2105 board

but not in real life operation where TX & RX are separated by hundreds of kms & they are

expected to work over a long period without additional setting up. The inherent short coming of

the delta modulator to pass DC level information is due to the fact that it passes the information

about the change in the voltage level & not the actual voltage level itself itself e.g. encodes the

change from -2V to -1V same as it would encode a change from +2V to +3V. In delta sigma

modulation the integrator is added in front of the delta sigma modulator. This simple

arrangement makes a big change in the circuit behaviour. It now responds to actual voltage levels

rather than the change in the voltage level. The effect of the addition of integrator before the

delta modulator can be done away by adding a differentiator at the end of the receiver. The

voltage comparator functionally can be thought of as a unity gain differential amplifier followed

by a zero-crossing detector. If the voltage comparator is replaced by this circuit, the no. of

integrators can be reduced to one (at the output of unit-gain differential amplifier).Similarly,

since the low pass filter is a linear circuit element the effect of integrator at the input of LPF is

nullified by the differentiator present at its output. Therefore, these two blocks are redundant in

the receiver. The resulting circuit looks as in figure 14 & 15. The system shown in the figure 12

& 13 can be simplified further. Since the voltage comparator is highly non-linear device cannot

transfer the two integrations at its input to one integration at its output.

BLOCK DIAGRAM:

( )

DIAGRAM:

Procedure:Initial setup of ST 2155:Clock frequency selector switches : A = 0 and B = 0 position.Integrator (1) blocks switches position:Gain control switch position : Left-hand side.Switches position : A=0 and B=0 position.Integrator (2) blocks switches position:Gain control switch position :Right-hand sideSwitches position : A = 0 and B = 0 position.Function Generator’s potentiometers position:1 KHz to 4 KHz Pots position : fully clockwise position1. Connect the main supply cord to the trainer.2. Connect the board as per figure 2.1.3. Switch ON the supply of trainer and oscilloscope.4. As the gain control switch is towards A & B switches, the gain setting is still manual, connect the voltage comparator's +ve input to 0V & check whether the modulator & demodulator are balanced for correct operation as in delta modulation experimentation. Change the clock frequency selector switches to the A=1, B=1, positions (400 KHz Clock Frequency) before continuing.5. Disconnect the voltage comparators '+' input from 0V and reconnect it to the 4 KHz output from the function generator block.

6. Monitor the 4 KHz analog input at TP14 and the output of integrator 1 at TP13.7. At the transmitter, move the slider of the gain control switch in the integrator 1 block to the right-hand position (towards the sockets labeled A, B). At the receiver, move the slider of the gain control switch in the integrator 2 block to the left-hand position (again towards the sockets labeled A, B). The gain of each integrator is now controlled by the outputs of the counter\ connected to it. Functionally, the transmitter and receiver are now configured as shown in the figure 9 & 10 i.e. as adaptive delta modulator and demodulator respectively.8. Once again examine the 4 KHz analog input at TP14 and the output of integrator 1 at TP13, noting that the" slope overloading problem has been eliminated, and that the integrator's output once again follows the analog input signal. Again, it may be necessary to adjust slightly the transmitter's level adjust preset, in order to obtain a stable trace of the integrator's output signal.9. Compare the output of integrator 1 (TP13) with that of integrator 2 (TP41); noting that, both are identical in appearance as expected. Output waveforms at TP13 and TP43 respectively Volts/Div: 5V Clock Frequency: 400 KHz Time/Div: 200usec Input Signal frequency: 4 KHz, 10Vpp

Automatic gain control of Tx. & Rx. Integrators

10. Examine the output of the low pass filter (TP42) and the output of integrator 2 (TP41). The filter has removed the high-frequency components from the integrator's output signal, to leave good, clean 4 KHz sine wave.11. Compare the original 4 KHz analog input signal (at TP15) with the output signal from the receiver's low pass filter at TP43). Note that the demodulator's output signal is identical to the modulator's input signal, but is delayed somewhat.12. Disconnect the voltage comparator’s '+' input from the 4 KHz function generator output, and reconnected it in turn to the 3 KHz, 2 KHz and 1 KHz outputs, noting in each case that the demodulator’s output signal is identical to the modulator's input signal, but delayed in time.

Output waveforms at TP13 and TP43 respectively Volts/Div: 5V Clock Frequency: 400 KHz Time/Div: 200usec Input Signal frequency: 1 KHz, 10Vpp

Automatic gain control of Tx. & Rx. Integrators

13. The adaptive delta modulator/demodulator system has therefore eliminated slope-overloading problems. To examine in details how it does this, reconnect the voltage comparator's '+' input to the function generator's 4 KHz output, then reduce the system clock (i.e. sampling) frequency to 50 KHz, by putting the clock frequency selector switches in the A=0, B=0 positions. 14. Monitor the 4 KHz analog input signal at TP14 and at the output of integrator 1 (TP13). It should now become a little clearer as to how the adaptive delta modulator is operating. It will be noted that the slope of the integrator's output signal is no longer constant, but increases in a series of discrete steps, in order to 'catch up' with the fast-changing analog input signal.15. Examine also the test points in the adaptive control circuit 1 block (TP22-25), to have an understanding of how the adaptive delta modulator is operating.16. While monitoring the outputs of the modulator's binary counter (TP22 and 23), slowly turn the 4 KHz preset anticlockwise, in order to reduce the amplitude of the 4 KHz analog input signal. Notice that once the analog input signal becomes small enough, both the counter's outputs becomes permanently low, causing the integrator to have minimum gain.

Applied Input OutputS.No I/P frequency I/P Voltage O/P Voltage1.2.3.4.

Experiment No 6.

AIM: Study of Amplitude Shift Keying.

APPRATUS: 1. ST2156 and ST2157 kit .2. 2 mm Banana cable3. Oscilloscope Caddo 802 or equivalent

4.Power supply.

THEORY: Amplitude shift keying - ASK - in the context of digital communications is a modulation process, which imparts to a sinusoid two or more discrete amplitude levels. These are related to the number of levels adopted by the digital message. For a binary message sequence there are two levels, one of which is typically zero. Thus the modulated waveform consists of bursts of a sinusoid.

There are sharp discontinuities shown at the transition points. These result in the signal having an unnecessarily wide bandwidth. Band limiting is generally introduced before transmission, in which case these discontinuities would be ‘rounded off’. The band limiting may be applied to the digital message, or the modulated signal itself. The data rate is often made a sub-multiple of the carrier frequency. This has been done in the waveform of Figure 1. One of the disadvantages of ASK, compared with FSK and PSK, for example, is that it has not got a

constant envelope. This makes its processing (eg, power amplification) more difficult, since linearity

becomes an important factor. However, it does make for ease of demodulation with an envelope

detector.

ASK signal (below) and the message (above)A significant reduction can be accepted before errors at the receiver increase unacceptably. This can be brought about by bandlimiting (pulse shaping) the message before modulation, or bandlimiting the ASK signal itself after generation.

(ASK generation method)where the message has been band limited. The shape, after band limiting, depends naturally enough upon the amplitude and phase characteristics of the band limiting filter.

Original TTL message (lower), band limited message (center), and ASK (above)

Procedure:1. Connect the power supplies of ST2156 and ST2157 but do not turn on the power supplies until connections are made for this experiment.2. Make the connections as shown in the figure 8.1.3. Switch 'ON' the power.4. On ST2156, connect oscilloscope CH1 to ‘Clock In’ and CH2 to ‘Data In’ and observe the waveforms.5. On ST2156, connect oscilloscope CH1 to ‘NRZ (L)’ and CH2 to ‘Output’ of modulator Circuit (l) on ST2156 and observe the waveforms.6. Vary the gain potentiometer of modulator circuit (l) on ST2156 to adjust the amplitude of ASK Waveform.7. On ST2156, connect oscilloscope CH1 to ‘NRZ (L)’ and CH2 to ‘Output’ ofcomparator on ST2157 and observe the waveforms.Observations:1. The output at ‘Data In’ is repeating sequence of bits generated by Data Source.2. The output at Modulator Circuit (l) is the ASK waveform which contains carriertransmitted for Data ‘1’ and carrier suppressed Data ‘0’.3. The output at comparator on ST2157 is the same as ‘Data In’ on ST2156.

(Waveforms Of ASK Modulation)

Precautions:

1. Check the connections before switching ON the kit.2. Observations should be taken properly.

Experiment No 7

AIM: Study of Frequency Shift Keying.

APPRATUS: 1. ST2156 and ST2157 kit .2. 2 mm Banana cable3. Oscilloscope Caddo 802 or equivalent

4.Power supply.

THEORY: In Frequency shift keying, the carrier frequency is shifted (i.e. from one frequency to another) corresponding to the digital modulating signal. If the higher frequency is used to represent a data ‘1’ & lower frequency a data ‘0’, the resulting FSK waveform appears. Thus

Data =1 High FrequencyData =0 Low Frequency

It is also represented as a sum of two ASK signals. The two carriers have different frequencies & the digital data is inverted. The demodulation of FSK can be carried out by a PLL. As known, the PLL tries to ‘lock’ the input frequency. It achieves this by generating corresponding O/P voltage to be fed to the VCO, if any frequency deviation at its I/P is encountered. Thus the PLL detector follows the frequency changes and generates proportional O/P voltage. The O/P voltage from PLL contains the carrier components. Therefore to remove this, the signal is passed through Low Pass Filter. The resulting wave is too rounded to be used for digital data processing. Also, the amplitude level may be very low due to channel attenuation.

DIAGRAM:

FSK Generation: As its name suggests, a frequency shift keyed transmitter has its frequency shifted by the message. Although there could be more than two frequencies involved in an FSK signal, in this experiment the message will be a binary bit stream, and so only two frequencies will be involved. The word ‘keyed’ suggests that the message is of the ‘on-off’ (mark-space) variety, such as one (historically) generated by a morse key, or more likely in the present context, a binary sequence. The output from such a generator is illustrated in Figure 1 below.

Procedure:1. Connect the power supplies of ST2156 and ST2157 but do not turn on the powersupplies until connections are made for this experiment.2. Make the connections as shown in the figure 3.1.3. Switch 'ON' the power.4. On ST2156, connect oscilloscope CH1 to ‘Clock In’ and CH2 to ‘Data In’ andobserve the waveforms.5. On ST2156, connect oscilloscope CH1 to ‘NRZ (L)’ and CH2 to ‘Output’ of

Summing Amplifier on ST2156 and observe the waveforms.6. Adjust the potentiometers of both the Modulator Circuit (l) &(ll) onST2156 toadjust the amplitude of FSK waveform at Summing Amplifier’s output onST2156.7. On ST2156, connect oscilloscope CH1 to ‘NRZ (L)’ and CH2 to ‘Output’ ofcomparator on ST2157 and observe the waveforms.Observations:1. The output at Summer Amplifier is the FSK waveform, Observe that for databit '0' the FSK signal is at lower frequency (960KHz) & for data bit '1’ the FSKsignal is at higher frequency (1.6 MHz)The output at comparator on ST2157 isthe same as ‘Data In’ on ST2156.

(Waveforms of FSK Modulation & Demodulation)

RESULT: The amplitude change in FSK waveform does not matter, therefore FSKmodulation technique is very reliable even in noisy & fading channels.

Experiment No 8

AIM: Study of Phase Shift Keying.

APPRATUS: 1. ST2156 and ST2157.2. 2 mm Banana cable3. CRO.4.Power supply.THEORY: Phase shift keying involves the phase change of the carrier sine wave between 0 and 180 in accordance with the data stream to be transmitted. PSK is also known as Phase reversal keying. PSK modulator is shown in figure 1. Functionally, the PSK modulator is very similar to the ASK modulator. Both uses balanced modulator to multiply the carrier with the modulating signal. But in contrast to ASK techniques, the digital signal applied to the modulator input for PSK generation is bipolar i.e. have equal +ve and –ve voltage levels. The unipolar – bipolar converter converts the unipolar data stream to bipolar data. At receiver, the square loop detector circuit is used to demodulate the transmitted PSK signal. The demodulator is shown in figure 2. The incoming PSK signal with 0 & 180 phase changes is first fed to the signal square, which multiplies the input signal by itself. The phase adjust circuit allows the phase of the digital signal to be adjusted w.r.t the input PSK signal. Also its O/P controls the closing of an analog switch. When the output is high the switch closes and the original PSK signal is switched through the detector.

BLOCK DIAGRAM:

(PSK MODULATED)

(PSK DE MODULATED)

Procedure:1. Connect the power supplies of ST2156 and ST2157 but do not turn on the powersupplies until connections are made for this experiment.2. Make the connections as shown in the figure 4.1.3. Switch 'ON' the power.4. On ST2156, connect oscilloscope CH1 to ‘Clock In’ and CH2 to ‘Data In’ andobserve the waveforms.5. On ST2156, connect oscilloscope CH1 to ‘NRZ (L)’ and CH2 to ‘Output’ ofModulator Circuit (l) on ST2156 and observe the waveforms.6. Adjust the ‘Gain’ potentiometer of the Modulator Circuit (l) on ST2156 toadjust the amplitude of PSK waveform at output of Modulator Circuit (l) onST2156.7. Now on ST2157 connect oscilloscope CH1 to ‘Input’ of PSK demodulator andconnect CH2 one by one to output of double squaring circuit, output of PLL,output of Divide by four (÷ 2) observe the wave forms.8. On ST2157 connect oscilloscope CH1 to output of Phase adjust and CH2 to‘output’ of PSK demodulator and observe the waveforms. Set all toggle switchto 0 and compare the waveform now vary the phase adjust potentiometer andobserve its effects on the demodulated signal waveform. (Note: If there isproblem in setting the waveform with potentiometer then toggle the switchgiven in PSK demodulator block two to three times to get the requiredwaveform).9. Now connect oscilloscope CH1 to ‘PSK’ output of PSK demodulator onST2157 and connect CH2 ‘Output’ of Low Pass Filter on ST2157 and observethe waveforms.10. Connect oscilloscope CH1 to ‘Output’ of Low Pass Filter on ST2157 thenconnect CH2 to ‘Output’ of Comparator on ST2157 and observe the waveforms,now vary the reference voltage potentiometer of first comparator to generatedesired data pattern.11. On ST2156, connect oscilloscope CH1 to ‘NRZ (L)’ and CH2 to ‘Output’ ofcomparator on ST2157 and observe the waveforms.12. Connect oscilloscope CH1 to ‘Data In’ then connect CH2 output to Bit decoderand observe the waveforms. If both data does not matches then try to match it byvarying the phase adjust potentiometer on QPSK Demodulator.

13. Now try to match the LED sequence by once pressing the reset switch onST2156.Observations:1. The output at ‘Data In’ is repeating sequence of bits generated by Data Source.2. The ‘Output’ of Modulator Circuit (l) is Phase Shift Keying modulated signal.3. The output of Double squaring circuit is sinusoidal signal (carrier signal) but frequency is four times higher than that of carrier used for modulation.4. The output of Phase Lock Loop (PLL) is clock signal of same frequency as thatof the output of double squaring circuit and output of Divide by two (÷ 2) isclock signal of frequency two times less than the output of PLL signal.5. The output of PSK demodulator is a signal having group of positive half cyclesand group of negative half cycles of the carrier signal.6. A low pass filter removes high frequency component from demodulated PSKsignal and it makes the signal smooth.7. The variation in reference voltage potentiometer affect the Data, to recover Datacorrectly potentiometer adjustment is necessary.8. The Phase Adjust potentiometer on ST2157 matches the phase of regeneratedclock and carrier with input clock and carrier signal.

(Waveforms of PSK Modulation)

(Waveforms of PSK Demodulation)Result:The PSK modulator and demodulator circuit has been studied.Precautions:

1. Check the connections before switching ON the kit.2. Observations should be taken properly.Experiment No 9

3. AIM: To Study Quadrature Phase Shift Keying transmission and Reception.4. APPRATUS: 1. ST2156 and ST2157.5. 2. 2 mm Banana cable6. 3. CRO.7. 4.Power supply.THEORY:-

Procedure:

1. Connect the power supplies of ST2156 and ST2157 but do not turn on the powersupplies until connections are made for this experiment.2. Make the connections as shown in the figure 6.1.3. Switch 'ON' the power.4. On ST2156, connect oscilloscope CH1 to ‘Clock In’ and CH2 to ‘Data In’ andobserve the waveforms.5. On ST2156, connect oscilloscope CH1 to ‘Clock Output’ and CH2 one by oneto ‘Sine’ and ‘Cosine’ output of 960 KHz and observe the waveforms.6. On ST2156, connect oscilloscope CH1 to ‘Data In’ and connect CH2 one by oneto ‘I Data’ and ‘Q Data’ outputs and observe the waveforms.7. Now connect oscilloscope CH1 to ‘I Data’ output on ST2156 and connect CH2one by one to ‘Signal In’, ‘Carrier In’ and ‘Output’ of modulator circuit (l) onST2156 and observe the waveforms.8. Now connect oscilloscope CH1 to ‘Q Data’ output on ST2156 and connect CH2one by one to ‘Signal In’, ‘Carrier In’ and ‘Output’ of modulator circuit (ll) onST2156 and observe the waveforms.ST2156 &ST2157Scientech Technologies Pvt. Ltd. 489. Now connect oscilloscope CH1 to ‘Data Out’ on ST2156 and CH2 to ‘Output’of Summing Amplifier on ST2156 and observe the waveforms.10. Set ‘Carrier frequency’ selection switch to ‘960 KHz’ on ST2157.11. Now on ST2157 connect oscilloscope CH1 to ‘Input’ of QPSK demodulatorand connect CH2 one by one to output of double squaring circuit, output ofPLL, output of Divide by four (÷ 4) observe the wave forms.12. On ST2157, connect oscilloscope CH1 to ‘I’ output of QPSK demodulator andCH2 to ‘Q’ output of QPSK demodulator and observe the waveforms. Set alltoggle switch to 0, now vary the phase adjust potentiometer and observe itseffects on the demodulated signal waveforms.13. Connect oscilloscope CH1 to ‘I’ output of QPSK demodulator on ST2157 thenconnect CH2 one by one to output of low pass filter, output of Comparator onST2157 and observe the waveforms.14. Connect oscilloscope CH1 to ‘Q’ output of QPSK demodulator on ST2157 thenconnect CH2 one by one to output of low pass filter, output of Comparator onST2157 and observe the waveforms.15. Compare the output of comparators on ST2157 with the output ‘I Data’ and ‘QData’ on ST2156 respectively.16. Connect oscilloscope CH1 to ‘Data In’ then connect CH2 output to Bit decoderand observe the waveforms. If both data does not matches then try to match it byvarying the phase adjust potentiometer on QPSK Demodulator.17. Now try to match the LED sequence by once pressing the reset switch onST2156.Observations:1. The output at ‘Data In’ is repeating sequence of bits generated by Data Source.2. The ‘I Data’ and ‘Q Data’ output are even and odd bit sequence of input datasequence and bit duration is double of input data sequence as shown in thefigure 11.2.

3. The ‘Output’ of Modulator Circuit (l) and Modulator Circuit (ll) are Phase ShiftKeying modulated signals, and summation of these two signals are QuadraturePhase Shifted signal as shown in the figure 6.2.4. The output of Double squaring circuit is sinusoidal signal (carrier signal) butfrequency is four times higher than that of carrier used.5. The output of Phase Lock Loop (PLL) is clock signal of same frequency as thatof the output of double squaring circuit and output of Divide by four (÷ 4) isclock signal of frequency four times less than the output of PLL signal.6. The output of QPSK demodulator is a signal having group of positive halfcycles and group of negative half cycles of the carrier signal as shown in the7. A low pass filter removes high frequency component from demodulated QPSKsignal and it makes the signal smooth as shown in the figure 6.3.8. The variation in reference voltage potentiometer affect the Data, to recover Data

correctly potentiometer adjustment is necessary and recovered Data.