-
Index
® Mitsubishi is a registered trademark and property of its
respective company.
Vehicle Application
Guide................................................................................................................................................
Installation (Wiring Diagrams & Vehicle Wiring Reference
Charts)Wiring
Diagram................................................................................................................................................................Vehicle
Wiring Reference
Chart.......................................................................................................................................Locating
Components......................................................................................................................................................
ProgrammingModule
Programming......................................................................................................................................................Module
Reset & Hard
Reset............................................................................................................................................Feature
and Option
List...................................................................................................................................................Feature
Programming......................................................................................................................................................
LED Diagnostics and
Troubleshooting............................................................................................................................
Limited One Year Consumer
Warranty............................................................................................................................
Quick Reference
Guide...................................................................................................................................................
02
030405
06070708
09
10
11
Door lock and transponder interface for Mitsubishi RVR (Smart
Key) and Outlander Sport (Smart Key). Features include door trigger
sensing, tach output, and FOB control.
Installation Guide
Update Alert: Firmware updates are posted on the web on a
regular basis. We recommend that you check for firmware and/or
install guide updates prior to installing this product.
Rev.: 20160212
Platform: DBALL/DBALL2Firmware: MIT1
© 2016 Directed. All rights reserved.
-
Vehicle Application GuidePage 2
Vehicles
2015
2014
2013
2012
2011
PK
-Im
mobilizer
Bypass-D
ata
No
Key
Req'd
AV
-Panic
Mode
Activ
atio
n
DL-A
rmF
acto
ryS
ecurity
DL-D
isarm
Facto
ryS
ecurity
DL-D
oor
Lock
Contr
ol
DL-D
oor
Unlo
ck
DL-D
river
Priority
Unlo
ck
DL-T
runk
/H
atc
hR
ele
ase
FO
B-C
ontr
olo
fafterm
ark
etala
rmw
ithO
EM
rem
ote
RS
-Tach
/R
PM
Outp
ut
SS
-Entr
yM
onito
ring
ALL
Door
Pin
s
SS
-Entr
yM
onito
ring
Driver
Door
Pin
SS
-Entr
yM
onito
ring
Hood
Pin
SS
-Entr
yM
onito
ring
Tru
nk/H
atc
hP
in
ST
-Bra
ke
Sta
tus
(footbra
ke)
ST
-E-B
rake
Sta
tus
ST
-Igniti
on
Sta
tus
Mitsubishi
Outlander Sport (Smart Key) • • • • • • • • • • • • • D • • D •
• • • D
RVR (Smart Key) • • • • • • • • • • • • • D • • D • • • • D
Legend:
D: Data-to-Data (D2D) only AV: Horn & Lights Controls RS:
Remote Start & Engine Controls
•: D2D and Wire-to-Wire (W2W) DL: OE Door Lock & Alarm
Controls SS: Integrated Security & Monitoring
FOB: Sync CAN Interface w / FOB Remote ST: Function/Feature
Status
PK: Transponder & Immobilizer Override
Rev.: 20160212
Platform: DBALL/DBALL2Firmware: MIT1
© 2016 Directed. All rights reserved.
-
Page 3
Wiring DiagramRefer to the Locating Components in the Vehicle
section on page 5 for more information.
C-4
08
C-413
C-412
C-411
1211
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
321
13 14 15 24
31 2
4 5 6
Rem
ote
Sta
rter
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: Trunk Release Input
4: White/Violet: Aux1 Panic Input
9: Pink: (+) Ignition Input
10: Blue/White: (-) GWR (Status) Input
Ignition Connector White
(right side of steering column)
(+) 12V
(+) Parking Lights:Pink, pin 13
(+) Parking Lights:Yellow, pin 10
6 Ampdiodes
(-) Ground
(+) Parking Lights (+) 12V
(-) Ground(-) Ground
(-) GWR (Status)
(+) Ignition Output
(-) Lock Output
(-) Unlock Output
(-) Trunk Release Output
Aux1 Panic Output(-) Trunk Status Input
(-) Door Status Input
(+) Brake Status Input
(-) Hood Status Input
(-) E-Brake Status Input
[1] (AC) Tach Input
C-411White connector
1
8
3
1012
2
9
4
1113
5
14
6
15
7
16
C-412Brown Connector
C-413White Connector
18 3
1012
29 4
111317
5
1418
6
1519
7
1620
Fuse Box (front view)Driver-side Kick Panel
CAN connections can also be found in passenger kick panel or
behind cluster,see Locating Components in theVehicle (Type 3) on
page 10 for details.
(+) Accessory
(+) Starter
TX
(-) GroundRX
(+)12V
10
RF
Prog. Button
LED
4
14
12
2
DBALL/DBALL2 P#: XKD2D65
(-) Driver Door Trigger:Yellow, pin 16
(+) Ignition: White, pin 2
(+) Starter:Blue, pin 5
(+) Accessory: Light Green, pin 6
FT CAN Low:Red, pin 7
FT CAN High:Green, pin 6
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote
starters, which do not support a tach signal in D2D.
All adapters are displayed from the wire side (unless specified
otherwise).
[1] (AC) Tach Output: Violet/White: 5
(+) Brake Status Output: Gray: 6
(-) Hood Status Output: Blue/Red: 12
(-) Door Status Output: Green/White: 3
(-) E-Brake Status Output: Black/White: 1
(-) Trunk Status Output: Red/Black: 4
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
(+) 12V: Red: 13
(-) Ground: Black: 14
(-) Auto Headlamp Shutoff Output: Green/Black: 2
C-408Black Connector
12
(+) 12V:Black/Red,pin 1
Rev.: 20160212
Platform: DBALL/DBALL2Firmware: MIT1
© 2016 Directed. All rights reserved.
-
Page 4
Vehicle Wiring Reference Chart
Function Color Pin Polarity Location Color Pins
FT CAN High Green 6 Data C-411 at Fuse Box, driver kick panel
White 24
FT CAN Low Red 7 Data C-411 at Fuse Box, driver kick panel White
24
Driver Door Trigger Yellow 16 (-) C-412 at Fuse Box, driver kick
panel Brown 16
Parking Lights Pink 13 (+) C-413 at Fuse Box, driver kick panel
White 20
Parking Lights Yellow 10 (+) C-413 at Fuse Box, driver kick
panel White 20
Accessory Lt. Green 6 (+) Ignition Connector, left side of
steering column White 6
Ignition White 2 (+) Ignition Connector, right side of steering
column White 6
Starter (automatic transmission only) Blue 5 (+) Ignition
Connector, left side of steering column White 6
(+)12V White 1 (+) C-408 at Fuse Box, driver kick panel Black
2
FT CAN High Green 6 Data C-411 at Fuse Box, driver kick panel
White 24
FT CAN Low Red 7 Data C-411 at Fuse Box, driver kick panel White
24
Driver Door Trigger Yellow 16 (-) C-412 at Fuse Box, driver kick
panel Brown 16
Parking Lights Pink 13 (+) C-413 at Fuse Box, driver kick panel
White 20
Parking Lights Yellow 10 (+) C-413 at Fuse Box, driver kick
panel White 20
Accessory Lt. Green 6 (+) Ignition Connector, left side of
steering column White 6
Ignition White 2 (+) Ignition Connector, right side of steering
column White 6
Starter (automatic transmission only) Blue 5 (+) Ignition
Connector, left side of steering column White 6
(+)12V White 1 (+) C-408 at Fuse Box, driver kick panel Black
2
Mitsubishi RVR (Smart Key) 2011-2015
Wire Information Connector Information
Mitsubishi Outlander Sport (Smart Key) 2011-2015
Rev.: 20160212
Platform: DBALL/DBALL2Firmware: MIT1
© 2016 Directed. All rights reserved.
-
Locating Components in the Vehicle
Ignition Connector White(left side of steering column)(+)
Accessory: Light Green, pin 6(+) Ignition: White, pin 2(+) Starter:
Blue, pin 5
C-413 - White Connector (at fuse box in driver-side kick
panel)(+) Parking Lights: Yellow, pin 10(+) Parking Lights: Pink,
pin 13
Cluster ConnectorC-203 - White(behind cluster)FT CAN High: Red,
pin 14FT CAN Low: Pink, pin 15
Blue Connector(passenger kick panel)FT CAN High: Pink, pin 10FT
CAN Low: Blue, pin 11
ETACS/ECU ConnectorC-408 - Black(at fuse box,in driver-side kick
panel)(+) 12v: Black/Red
Page 5
C-412 - Brown Connector (at fuse box in driver-side kick
panel)(-) Auto Headlamp Shutoff Output: Yellow, pin 16
Rev.: 20160212
Platform: DBALL/DBALL2Firmware: MIT1
© 2016 Directed. All rights reserved.
-
Page 6
Module Programming
4
3 The LED turns ON green for 3 seconds and shuts OFF.
Press the PTS button 1x to turn ignition OFF.
Without applying the brakes, press the PTS button 2x to turn
ignition ON.2
&
IMPORTANT for PTS vehicles! Takeover is NOT possible. The
vehicle will shut down if a door is opened.
1Solid
OffSolid x3 secs
Wait until the LED turns ON solid red.
You have successfully completed the module programming
sequence.
ImportantMake all the required connections to the vehicle, as
described in the wiring diagram(s) found in this guide, and double
check to ensure everything is correct prior to moving onto the next
step.
Warning! To take advantage of advanced features, you must use
XpressVIP 4.5 (and higher) or the Directechs Mobile app.
When the flashing operation is successful, you can proceed with
the programming instructions below.
Refer to the LED Diagnostics section on page 16 for more
information and for troubleshooting purposes.
OR
If required for your installation, connect the 10-pin, 12-pin
and 14-pin harnesses to the module, then connect the 4-pin D2D
harness.
D2D Installation
W2W Installation
If required for your installation, connect the 10-pin and 12-pin
harnesses to the module, then connect the 14-pin harness to the
module.
10-pinD2D
st1
12-pin14-p
in
nd2
rd3
10-pinD2D
st1
th4
12-pin14-p
in
nd2
rd3
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and select
the Flash Module button.
3. Follow the instructions to select your vehicle, installation
type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or
tablet.
3. Select FLASH YOUR MODULE and follow the on screen
instructions.
Press
PUSHENGINESTARTSTOP
Press 2x
PUSHENGINESTARTSTOP
Rev.: 20160212
Platform: DBALL/DBALL2Firmware: MIT1
© 2016 Directed. All rights reserved.
-
Rev.: 20160212
Platform: DBALL/DBALL2Firmware: MIT1
© 2016 Directed. All rights reserved.
2
Solid
&
Solid Flashes
&
Release
3
Wait 3 seconds until the LED turns ON solid orange, and wait 10
more seconds until the LED starts to flash orange and red.
Release the programming button. The LED turns ON solid red.
Warning Against Executing a Hard Reset! A hard reset will revert
the flashed firmware back to its default settings. Depending on the
installation, some settings (such as RFTD and D2D options) may have
to be reconfigured. See the Feature & Option List section of
this guide.
1 OR
If required for your installation, connect the 10-pin, 12-pin
& 14-pin harnesses to the module. Press and hold the
programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin &
12-pin harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
st1
12-pin14-p
in
nd2
th4
rd3
10-pinD2D
st1
th5
12-pin14-p
in
nd2
rd3
th4
Module Reset
Hard Reset
2 & &Solid SolidRelease
Wait 3 seconds until the LED turns ON solid orange then release
the programming button. The LED then turns ON solid red.
A module reset will only erase programming performed in the
previous steps. All settings (firmware) and settings flashed to the
module using the web config tool will not be affected.
1 OR
If required for your installation, connect the 10-pin, 12-pin
& 14-pin harnesses to the module. Press and hold the
programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin &
12-pin harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
st1
12-pin14-p
in
nd2
th4
rd3
10-pinD2D
st1
th5
12-pin14-p
in
nd2
rd3
th4
Page 7
-
Feature and Option ListPage 8
Features Operation Option Description
No RF Output*Module is connected to a remote starter
using a standard installation.
RFTD OutputModule is connected to an XL202 using an
RSR or RXT installation (when available).
* Default Option
1RF Output type Activate this feature w henever an external
RFTD
module is used (i.e. XL201 or XL202).
To enter feature programming routine- Turn the ignition ON, then
OFF. - Within 5 seconds, press and HOLD the programming button
until the LED turns ON orange (after 3 seconds). Release the
Programming button.- The LED will flash green once slowly to
indicate the feature number is 1. After a short delay, the LED
flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x
red indicates feature 1 is set to option 1). The flashing sequence
will repeat until a new command is entered.
Changing feature options- Press the lock/arm or unlock/disarm
button on aftermarket transmitter to change the option of the
selected feature. - The LED flashes red rapidly the number of times
equal to the current option number. After a short delay, the LED
flashes green slowly
the number of times to indicate the current feature. The
flashing sequence will repeat until a new command is entered.
Accessing another feature- Press and release the programming
button a number of times to advance from the current feature to the
next desired feature. - The LED flashes green slowly the number of
times equal to the feature number. After a short delay, the LED
flashes red rapidly to
indicate the current option of the current feature. The flashing
sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the
LED will start flashing again from the first feature or option.
Once a feature is programmed- Other features can be programmed.-
The feature programming can be exited.
Exiting feature programming- No activity for 30 seconds; after
30 seconds, the LED will turn ON orange for 2 seconds to confirm
the end of the programming
sequence.OR
- Press and HOLD the programming button for 3 seconds. After 3
seconds, the LED will turn ON orange for 2 seconds to confirm the
end of the programming sequence.
Feature ProgrammingProgramming
Button
Rev.: 20160212
Platform: DBALL/DBALL2Firmware: MIT1
© 2016 Directed. All rights reserved.
-
LED Status Description Troubleshooting
Module Programming
Solid red Waiting for the ignition to turn on.
Make sure that all the connections are correct (see
install sheet) and turn the ignition ON to begin the
programming sequence.
Flashes orangeCAN has been successfully
detected.
Make sure you keep the key to the ON position long
enough to let the programming finish.
Flashes greenVehicle has been successfully
detected.Normal operation.
Solid green for 3
seconds
Module has been successfully
programmed.Normal operation.
Active Ground While Running
Flashes green Ground out (GWR) is active. Normal operation.
Off Normal operation.
The Ground While Running (status) wire is incorrectly
connected. Refer to the wiring diagram to make the right
connections.
Inactive Ground While Running
Flashes green once Lock function has been executed.
If it does not flash, the bypass module did not receive the
signal. Verify the connections between the bypass and
the remote starter module.
Flashes green twiceUnlock function has been
executed.
If it does not flash, the bypass module did not receive the
signal. Verify the connections between the bypass and
the remote starter module.
Flashes green 3 timesTrunk release function has been
executed.
If it does not flash, the bypass module did not receive the
signal. Verify the connections between the bypass and
the remote starter module.
Page 9
LED Diagnostics and Troubleshooting
Solid
Solidgreenx3 sec
Flashesorange
Flashesgreen
Flashesgreen x1
Flashesgreen x2
Flashesgreen x3
Flashesgreen
Off
Rev.: 20160212
Platform: DBALL/DBALL2Firmware: MIT1
© 2016 Directed. All rights reserved.
-
For a period of ONE YEAR from the date of purchase of a Directed
Electronics remote start or security product, Directed Electronics.
(“DIRECTED”) promises to the original purchaser, to repair or
replace with a comparable reconditioned piece, the security or
remote start accessory piece (hereinafter the “Part”), which proves
to be defective in workmanship or material under normal use,
provided the following conditions are met: the Part was purchased
from an authorized DIRECTED dealer; and the Part is returned to
DIRECTED, postage prepaid, along with a clear, legible copy of the
receipt or bill of sale bearing the following information:
consumer’s name, address, telephone number, the authorized licensed
dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if
the Part has been modified or used in a manner contrary to its
intended purpose or the Part has been damaged by accident,
unreasonable use, neglect, improper service, installation or other
causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE,
ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY,
IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR
PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL
PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR
AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY,
OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED
HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL
ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS
NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR
THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY
DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION,
LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM
OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE
SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA
STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE
DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED
SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S
PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR
ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY
CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF
TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC
OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE
MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT
DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of
America and Canada. Parts sold outside of the United States of
America or Canada are sold “AS-IS” and shall have NO WARRANTY,
express or implied. Some states do not allow limitations on how
long an implied warranty will last or the exclusion or limitation
of incidental or consequential damages. This warranty gives you
specific legal rights and you may also have other rights that vary
from State to State. DIRECTED does not and has not authorized any
person or entity to create for it any other obligation, promise,
duty or obligation in connection with this Part.For further details
relating to warranty information of Directed products, please visit
the support section of DIRECTED’s website at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on
the listed vehicles. Other vehicles will be added to the select
vehicle list upon completion of compatibility testing. Visit
website for latest vehicle application guide. DISCLAIMER: Under no
circumstances shall the manufacturer or the distributors of the
bypass kit / data bus interface part(s) be held liable for any
consequential damages sustained in connection with the part(s)
installation. The manufacturer and it’s distributors will not, nor
will they authorize any representative or any other individual to
assume obligation or liability in relation to the interface kit /
data bus interface part(s) other than its replacement. N.B.: Under
no circumstances shall the manufacturer and distributors of this
product be liable for consequential damages sustained in connection
with this product and neither assumes nor authorizes any
representative or other person to assume for it any obligation or
liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004
B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1;
6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886
B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1;
7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153
B1; 7,205,679 B1; Cdn. Patent:
Limited One Year Consumer WarrantyPage 10
Rev.: 20160212
Platform: DBALL/DBALL2Firmware: MIT1
© 2016 Directed. All rights reserved.
-
Quick Reference GuideDBALL/DBALL2-MIT1
© 2016 Directed. All rights reserved.
Button(s) Actions
Press & hold for 1 second to lock.
Press & hold for 1 second to unlock.
Press & hold for 1 second to remote
start.
Press & hold for 5 seconds to activate
the trunk release (optional).
Press once, then to activate the
rear hatch/tail glass release (optional).*
Press 3 times, then to activate
the panic mode.
Press once, then to reset the
remote starter runtime.
List of Available Commands
x1 +
x3 +
x1 +
* This output is configurable. see your authorized installation
center for more information.
Note that the information below is for Viper, Clifford and
Python models. Icons and commands may differ depending on the
remote brand and model purchased. Refer to your authorized
installation center for more information.
Notes
1: Index2: VAG3: WD4: RC5: LOC6: Prog7: Reset8: Feature Prog9:
LED diag10: WarrantyDBALL-DBALL2-MIT1_EN_QRG_TH20160119.pdf1:
User