www.sunrisetelecom.com Combining the power of a benchtop SDH/PDH set and protocol analyzer into a handheld platform, the SunSet SDH offers advanced testing for SDH, PDH, and ATM networks and services. With electrical and optical interfaces, the SunSet SDH tests from 64 kbit/s to 622 Mbit/s (STM-4). Its lightweight, durability, long battery life, and low cost make it the ideal tool for field technicians in the access and metropolitan networks. And with jitter and wander testing capabilities, save time and money for installation, maintenance, troubleshooting, and commissioning tasks, either at the central office or in the field. KEY features • SDH testing at 52, 155, and 622 Mbit/s • PDH & T-Carrier testing at 1.5, 2, 34, 45, and 139 Mbit/s; PDH/T-Carrier structured mode • Bit error rate testing and error performance analysis per ITU-T G.821, G.826, G.828, G.829, M.2100, M.2101, and M.2110 • SDH-SDH, SDH-PDH MuxTest modes; Independent Tx and Rx for testing ADMs and synchronous multiplexers • SDH/PDH MuxMode: drop and insert of 1.5/2M tributaries • Full SDH overhead control and decode • Tributary scan for alarm and error monitoring • APS timing measurement and APS bytes capture • Pointer monitoring, pointer adjustment, pointer offset and G.783 pointer test sequences • ITU-T compliant Jitter generation, measurement, tolerance & transfer tests, pointer jitter test in MuxTest mode • Real time wander TIE measurements and offline MTIE/ TDEV analysis software conforming to ITU-T G.811, G.812, G.813, G.823 • Pulse mask analysis at 1.5, 2, 34, and 45 Mbit/s • Tandem connections: errors, alarms, APId capture and generation • Voice frequency testing: talk/listen, send/receive tones, noise measurements • ATM testing at 1.5, 2, 34, 45, 155, and 622 Mbit/s • ATM traffic generation, ATM QoS measurements, ATM Adaptation Layer (AAL0, AAL1, AAL2, AAL5) tests • IP over ATM testing, ATM DSL DSLAM test Benefits • SDH/PDH/ATM feature-rich • Lightweight and highly portable • Eliminates the need for multiple and heavier instruments without compromising test features or accuracy • Intuitive and easy-to-use • Cost-effective and future-proof • Increases efficiency • Consolidates training and shortens the learning curve • Handles multiple tasks including installation, maintenance, troubleshooting, and commissioning Benchtop performance in a handheld test set - the SunSet SDH SunSet ® SDH with Jitter and Wander
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
www.sunrisetelecom.com
Combining the power of a benchtop SDH/PDH set and protocol analyzer into a handheld platform, the SunSet SDH offers advanced testing for SDH, PDH, and ATM networks and services. With electrical and optical interfaces, the SunSet SDH tests from 64 kbit/s to 622 Mbit/s (STM-4). Its lightweight, durability, long battery life, and low cost make it the ideal tool for field technicians in the access and metropolitan networks. And with jitter and wander testing capabilities, save time and money for installation, maintenance, troubleshooting, and commissioning tasks, either at the central office or in the field.
• Eliminatestheneedformultipleandheavierinstrumentswithout compromising test features or accuracy
• Intuitiveandeasy-to-use
• Cost-effectiveandfuture-proof
• Increasesefficiency
• Consolidatestrainingandshortensthelearningcurve
• Handlesmultipletasksincludinginstallation,maintenance, troubleshooting, and commissioning
Benchtop performance in a handheld test set - the SunSet SDH
SunSet® SDHwith Jitter and Wander
2 SunSet SDH
Applications
Installation, Maintenance, Troubleshooting & CommissioningThe SunSet SDH is the ideal product for installation and bringing into service tasks in the field and central office. Commission-ing and acceptance tests can be performed with the same test set, as jitter and wander features are part of the conformance procedures. Maintenance and troubleshooting in-service tasks can also be completed with the same handheld test set saving time and money.
Path overhead monitor and decodeTextencodingofallapplicablebytes(K1,K2,S1,C2,etc.)
Programmable POH bytesDCCBERtestingthroughD1toD3,D4toD12bytesOrderwire:Talk/listenthroughE1,E2bytesPointer monitor AU(bytesH1andH2),TU(bytesV1andV2)Display number of pointer operations with respect to time− Instantaneous pointer value display− Graphical display of pointer movements with histogram
formatPointer adjustmentProgrammingofpointervalue,NDF,andSSbitsIncrease and decrease the pointer value
Through ModeLine throughPayload throughAllSOHbytescanbemodifiedexceptforB1,B2,H1,H2bytesAlarms/errorinsertion:LOS,LOF,MS-AIS,MS-RDI,B1,B2,MS-REI
Pointer Test SequencesSpecification:ITU-TG.783AU or TU pointerSequences:Single,burst,phase,transientburst,periodic,87-3,26-1,opposite(increase+decrease),andcustom
Tandem Connections MonitoringN1byteforHighOrderPaths(VC-3/VC-4)N2byteforLowOrderPaths(VC-11/VC-12)Analysis of data, display of data in the form of alarms, performance figures,andAPIdmessagesasspecifiedinITU-TG.707
Generationanddetectionofthefollowingparameters:Loss of Tandem Connection (LTC)Loss of Multiframe (LOM)IncomingErrorCount(IEC)TandemConnectionRemoteErrorIndication(TC-REI)Tandem Connection Alarm Indication Signal (TC-AIS)TandemConnectionRemoteDefectIndication(TC-RDI)Tandem Connection Outgoing Defect Indication (TC-ODI)TandemConnectionOutgoingErrorIndication(TC-OEI)TandemConnectionUnEquipped(TC-UNEQ)TandemConnectionErrorsDifference(TC-DIFF)
Graphical display
Automatic Protection Switch Time MeasurementMeasures time that anomaly is presentResolution:1msAnomalyselection:MS-AIS,B2errors,B3error,AU-AIS,TU-AIS,LOSSelectableswitchtimetodisplayPASSorFAILSelectable gate time to control the minimum interval for the circuit
to be anomaly time
5www.sunrisetelecom.com
APStimingat2Minterfaces:2M-AIS,2M-LOSAPS bytes captureCaptureanddecodestatesofK1/K2bytes– Store hundreds of messages–Ringandlineardecoding125µsresolutionOptional trigger with wildcardsTimestamp in frames or msDuration in absolute or elapsed timeSave or print resultsLoad and decode past results
PDH/T-Carrier Error Injection139M,34M:Code,Bit,FAS45M:Code,Bit,Frame,C-bit,P-bit,FEBE2M:Code,Bit,CRC-4,E-bit,FAS1.5M:BPV,Logic,CRC-6,FrameProgrammableerrorburst1to9999countorerrorrate2x10-3 to 1x10-9
Voice Frequency Testing (SWSDHJ-114) Monitor speaker with volume control Built-inmicrophone/speakerCompanding:A-law,µlawProgrammableidlechannelA,B(C,D)bits(1.5M)ABCDbitstransmitandmonitorinselectedchannel(2M)VFlevelmeasurement:+3to-60dBm,resolution0.1dBmVFfrequencymeasurement:50to3950Hz,resolution1HzVFtonegenerationVariabletone:50to3950Hz@1Hzstep.+3to-60dBm@1dBm
Peak code and coder offset measurementsNoisemeasurementsReceiverfilters2M:3.1kHz,Psophometric,1010Hznotch1.5M:3kHzflat,C-message,C-notch
Auto ConfigurationSingle button configurationAutomatically scans all test interfaces for signalConfigures test set based on received signalSets rate, mapping, payload, and/or test pattern
Measurement CriteriaTest results/events storage and events log capabilityStoresupto20testresultsor800errorsoralarmseventswithuserdefinablelabels;lock/unlockrecords,availabletoscreenvieworprint
Storesupto10userconfigurations(profiles)withalphanumericlabelsPrint on event can be enabled or disabledPrintattimedinterval(settablefrom2minupto999hr59min)Measurementdurationcontinuousortimed(settableupto999hr,59min)
Elapsedtime,remainingtimeProgrammable start date and timeAudiblealarm:On/offswitchable
CSVformatstorageStatus and Alarm IndicatorsPowerandlowbatteryLEDindicatorsPatternSyncandBitError139MandSTM-N(signal),Alarm,Frame,Errors,Pointer,ATMcell8M,34Mand45M(signal),Alarm,Frame,andErrors1.5/2M-L2,Alarm,Errors1.5/2M-L1,Alarm,Errors
Userprogrammabletemplate(frequencypoints&litudevalues)Technique:OnsetoferrorsStorage:Upto20recordsJitter Transfer MeasurementPASS/FAILtemplate:PerITU-TG.735,G.736,G.737,G.742,G.751,G.7521.544Mbit/s(from10Hzto40kHz)2.048Mbit/s(10Hzto100kHz)34.368Mbit/s(100Hzto800kHz)44.736Mbit/s(10Hzto400kHz)
Quality of ServiceTimed or continuous measurementProgrammable start time and dateTraffic Supervision8independentVCCfilters:1foreground,7backgroundForeground:FullQoS,BERT,OAMcounter,andstatisticsBackground:TrafficstatisticsandOAMmonitoringonlyQualityofService:ErroredcellsandCER,lostcellsandCLR,misin-sertedcellsandCMR,SECBandSECBrate
Total, congested, tagged count and rate Cps (cells per second)Biterrorsandbiterrorrate,CRCerrorsOAMcellcount:F4/F5,segment/end-to-end,AIS/RDI/loopbackOAMcount:Continuitycheck,PerformancemanagementGraphicaldisplayinhistogramformatofbiterrors,CHEC,NCHEC,celllossseconds,cellerrorsandOAMcellcount(F4/F5,segment/end-to-end,AIS/RDI,loopback)
ATM View Test RecordsStoresupto20ATMtestresultswithuserdefinablelabels
Lock/unlock records, available to screen view or printTransferabletoPCinCSVformatbyusingWindowsRemoteControl
Cell Capture & DecodeCelltypecaptureselection:User,OAM,USER+OAMFullbufferoptiontocycleorstopTimed or continuous captureProgrammable start time and dateDisplaycellheaderandpayloadof4096cellsHeaderdecode:GFC,VPI/VCI,PTI,CLP
DSLAM TestingATM end-to-end connectivity test between customer premises (SSxDSL/MTT)andCO(SSSDH);back-to-backwithSunSetxDSL/MTTATU-RModule–SunSetxDSL/MTTrequiressoftwareoptionSWxDSL-xxATM–AutodetectionofSSxDSL/MTTatfarend
Bidirectional,asymmetricDSLthroughputtestingUpstream and downstream statisticsTxandRxcellratesCellloss%Biterrorcount,BER,andbiterrorinjection
ClearPass/FailindicationTest results available on both units