Data Acquisition Concepts Data Translation, Inc. Basics of Data Acquisition.

Data Acquisition ConceptsData Acquisition Concepts

Data Translation, Inc.Basics of Data Acquisition


Typical data acquisition applications

• Physiological studies

• Environmental studies (temperature, etc.)

• Materials testing

• Medical research

• Quality control and testing


Typical data acquisition applications

• Strain, pressure, temperature and vibration analysis

• Fluid analysis

• Manufacturing automation

Data Acquisition ConceptsData Acquisition ConceptsComponents of a data acquisition systems• Analog to digital conversion (A/D)

• Digital to analog conversion (D/A)

• Digital input/output (DIO)

• Pacer clock


Analog to Digital Conversion (A/D)

• Once data has been converted from analog to digital, the digital information can then be processed by the computer, or transferred to memory


Digital to Analog Conversion (D/A)

• D/A converters convert stored data back to a continuous signal (analog voltage) for display or control purposes

• Output from the D/A converter can be used to drive external devices which require an analog input


Digital Input/Output (DIO)

• Used primarily for control purposes

• Used to transmit data between the host processor and an external digital device that expects to receive 1’s and 0’s


Pacer Clock

• Used to initiate repetitive data conversions

• Used to control the sampling rate of conversions


What is analog?

• Analog signals are “continuous” signals

• Represented by continuously changing physical quantities

• Level of signal can be increased or decreased indefinitely

• Ex. temperature, pressure, strain, voltage


What is digital?

• Digital signals are “discrete” signals

• Represented by separate, individual units

• Units are represented by “bits” (binary digit)

• Bits are represented by one of two possible states: on/off, true/false, 1/0


What is data acquisition?

• A method of acquiring an analog signal and converting (digitizing) it into a binary code which can be manipulated by a computer

Computer

Analog Signal

Analysis


A/D Interface

• Converts analog data into digital data which can be processed

• Typical components:– Multiplexers– Amplifiers– Sample and hold circuits– A/D converters


A/D Converter Functions

• Input and output (I/O)– Analog input is converted into a digital

number, by comparing the voltage with its position within the Full Scale Range

– With an n-bit A/D converter the number of output levels equals 2n – e.g. 12-bit converter = 212 = 4096


Full Scale Range (FSR)

• Full scale range refers to the largest voltage range which can be input into the A/D converter


Range

• Range is an input span for an A/D and D/A system

• Typical ranges are based on available sensors– Uni-polar (positive)

• 0 to 5 volts• 0 to 10 volts

• Bipolar

•-5 to +5 volts

•-10 to +10 volts


Full scale range examples

+10v

0v

+10v +1.25v

-10v -1.25v

FSR = 10v FSR = 20v FSR = 2.5v


Input/Output

Analog Digital(101110010011)


Resolution

• Resolution determines the smallest change that can be detected

• Specified in bits. Determines number of output levels, or steps– 8 bits = 256 steps– 10 bits = 1024 steps– 12 bits = 4096 steps– 16 bits = 65,536 steps


Typical Resolutions

• 8-bit – common for image capture

• 10-bit – general analog acquisition

• 12-bit – general analog acquisition

• 16-bit – precision analog acquisition

• 24-bit – high-accuracy analog acquisition


Output Levels/Resolution Example

1-bit A/D Converter

1

0

+10v

0v



2-bit A/D Converter

11

00

+10v

0v

10

01



4-bit A/D Converter

+10v

0v

1111

111011011100

1011

10101001

1000011101100101

0100

0011001000010000



12-bit A/D Converter

1111 1111 1111

0000 0000 0000

+10v

0v

4096 Output Levels



16-bit A/D Converter

1111 1111 1111

0000 0000 0000

+10v

0v

65,536 Output Levels


LSB

• LSB stands for “least significant bit”

• An LSB represents the smallest change that can be resolved by the A/D converter

• An LSB carries the smallest value or weight

• An LSB is the rightmost bit

• LSB = Full Scale Range (FSR) ÷ 2n


What affects conversion speed?

• A/D converter only

• A/D converter and related circuitry

• A/D system and host


Acquisition time

• The time required to perform a complete conversion from the analog signal to digital

• The time required after receipt of “start digitizing” command until the A/D converter has finished digitizing


Settling time

• Time it takes to switch to a new channel

• Each time a user switches between channels, there is a delay, referred to as settling time


Throughput rate

• The inverse of A/D conversion time + acquisition time

• Measured in Hertz (Hz), which means the number of conversions per second

• The maximum rate at which the data conversion system can operate, while maintaining a specific accuracy


Throughput

• Acquisition System– The acquisition system determines the

maximum throughput possible– The entire system (host, disk, A/D board,

and program) determines the practical throughput


Throughput

• Throughput is specified as an aggregate of all channels– A/D runs at a constant rate– Number of channels determines

throughput per channel

• The host computer and software must be able to service the A/D board before the next conversion is complete


Speeding up throughput rate

• Overlap mode - while one sample is in Sample and Hold circuitry, the next is read into the multiplexer

• Throughput equals the greater of conversion time OR acquisition time, plus any time needed for Sample and Hold switching


Getting signals into the computer

• Transducers convert physical variables into electrical outputs

• An input transducer (sensor) then supplies its output to signal conditioning circuitry (on a Screw Terminal Panel)

• Signal conditioning circuitry prepares for interfacing with the PC


Amplification

• The output of a sensor usually requires amplification

• Apply gain


Gain

• A scale (multiplying) factor which increases an input signal to better utilize the range of the A/D converter


Gain

• Gain is the amplification applied to a signal to bring it to the range of the A/D system– High Level Gains (PGH) for high level

signals – 1, 2, 4, 8– Low Level Gains (PGL) for low level

signals – 1, 10, 100, 500


Selecting Gain and Range

5 volts

0 volts

0 volts

10 volts

User Input Selected Range (uni-polar)

Only 50% of the available A/D range is used.



5 volts

0 volts

-10 volts

+10 volts

User Input Selected Range (bipolar)


0 volts



0.25 v

-0.25 v

-10 volts

+10 volts



0 volts

Gain Amp

10



1 volt

0 volts

-10 volts

10 volts


Using this range only utilizes 1/20th of the range. This would allow the input to be divided into 205 increments.

0 volts



1 volt

0 volts

0 volts

1.25 volts

User Input Selected Range (uni-polar)

Using this range utilizes 8/10ths of the range. This would allow the input to be divided into 3277 increments.


Selecting the Best Gain & Range

• Analog input and output boards are generally designed to interface to the majority of sensors that are available

• The ranges used on I/O boards may not always be appropriate for every application



• To get the highest degree of accuracy possible out of an I/O board – try to utilize as much of the available range as possible

• Use internal or external gain selection



• Determine the maximum range that the input signal will use

• Determine if the signal is uni-polar (above zero) or bipolar (above and below zero)

• Evaluate the available gain and range combinations to select the most appropriate product


PGL Range/Gain Combinations

Gain Effective Range

Step Size (LSB)

12-bit 16-bit

1 0-10 v 2.4414 mv 152.6 µv

10 0-1 v 2.4414 µv 15.26 µv

100 0-100 mv 24.414 µv 1.526 µv

500 0-20 mv 4.8828 µv 0.305 µv

Uni-Polar and PGL Example




Step Size (LSB)

12-bit 16-bit

1 ± 10 v 4.8828mv 305 µv

10 ± 1 v 488.28 µv 30.5 µv

100 ± 100 mv 48.828 µv 3.05 µv

500 ± 20 mv 9.7656 µv 0.61 µv

Bipolar and PGL Example




Step Size (LSB)

12-bit 16-bit

1 0-10 v 2.4414 mv 152.6 µv

2 0-5 v 1.2207 mv 76.29 µv

4 0-2.5 mv 610.35 µv 38.147 µv

8 0-1.25 mv 305.17 µv 19.073 µv

Uni-Polar and PGH Example




Step Size (LSB)

12-bit 16-bit

1 ± 10 v 4.8828 mv 305 µv

2 ± 5 v 2.4414 mv 152.6 µv

4 ± 2.5 v 1.2207 mv 76.27 µv

8 ± 1.25 v 610.35 µv 38.147 µv

Bipolar and PGH Example


Methods of Transferring Data to Memory

• Programmed input/output (PIO) – this is older technology and is slow– Polled I/O– Interrupts (shared and not shared)

• Direct memory access (DMA)


Polled I/O

• Data transfer is controlled by the CPU

• CPU monitors the Data Ready bit of the A/D converter

• When data is ready, the CPU reads it, then transfers it to memory

• Very slow


Direct Memory Access (DMA)

• Data is transferred directly from the data acquisition board to system memory

• Frees CPU and speeds throughput

• Board activates request line to use DMA controllers


Direct Memory Access (DMA)

• DMA controller receives request, acts upon it and sends back an acknowledge to the board

• Acknowledge is received; board puts data on the bus to be stored in memory


DMA: Two Methods

• Single channel for medium throughputs

• Dual channel for high throughputs


Conclusion

Additional data acquisition questions? Contact Data Translation at

(800) 525-8528

Data Acquisition Concepts Data Translation, Inc. Basics of Data Acquisition.

Documents

analog data

digital data

stored data

analog input slide

repetitive data conversions

voltage slide

ad converter slide

digital conversion ad