1.1/89 1 CYLINDER SERIES ISO 15552 (EX ISO 6431), Ø 32-63 mm TWO-FLAT COMPONENTS PISTON ROD: stainless steel. HEAD: die cast aluminium, fully machined PISTON ROD GASKET: polyurethane GUIDE BUSHING: sintered bronze BARREL: drawn anodised calibrated aluminium HALF-PISTON: self-lubricating technopolymer with built-in cushioning olives PISTON GASKET: Ø 32÷63 polyurethane MAGNET: plastoferrite Static O-rings: NBR CUSHIONING GASKET: polyurethane CUSHIONING NEEDLE: OT 58 with needle out movement safety system even when fully open SCREWS: Tap Tite for assembly 4 10 2 3 5 6 8 7 12 11 1 9 This version of cylinder is used to keep the parts fixed to the piston rod at an angle and to apply torques within the specified limits. The piston rod of the Two Flat has two opposing longitudinal surfaces; it is made of stainless steel. The front cylinder head includes a sintered bronze bush that matches the profile of the piston rod and prevents it from rotating on its own axis. A special polyurethane gasket ensures pneumatic seal and prevents the accumulation of dirt. This technical solution is more reliable and gives a better pneumatic seal than with square or hexagonal piston rods. The cylinders are made to ISO15552 standards. They are available in several versions and with a wide range of accessories: • with or without magnet • double acting, single piston rod • double acting, through rod; one piston rod is Two Flat, the other cylindrical • fixing accessories. POLYURETHANE max 10 bar (max 1 MPa - 145 psi) –20 ÷+80 (non-magnetic cyl.) –20 ÷+70 (magnetic cyl.)) Unlubricated air. Lubrication, if used, must be continuous Ø 32 ; Ø 40 ; Ø 50 ; Ø 63 Heads with Tap Tite screws Ø 32= 300 Ø 40= 400 Ø 50= 500 Ø63= 500 ✚ Maximum recommended strokes. Higher values can create operating problems Double-acting cushioned, Through-rod cushioned, no-stick slip* All versions come complete with magnet. Supplied without magnet on request. Ø 32= 0.4 Ø 40= 0.4 Ø 50= 0.3 Ø63= 0.3 Ø 32= 0.2 Ø 40= 0.4 Ø 50= 1 Ø63= 1 Ø 32= 0.70° Ø 40= 0.75° Ø 50= 0.65° Ø63= 0.65° See GENERAL TECHNICAL DATA PAGE 1.1/05 See GENERAL TECHNICAL DATA PAGE 1.1/06 *Using for speeds lower than 0.2m/s, to prevent surging. For no-stick-slip versions use no-lubricated air only TECHNICAL DATA Operating pressure Temperature range °C Fluid Bore Design Maximun stroke ✚ mm Versions Sensor magnet Inrush pressure Max torque on piston rod Nm Maximum rotation on the rod degrees Forces generated at 6 bar thrust/retraction Weights
14
Embed
CYLINDER SERIES ISO 15552 (EX ISO 6431), Ø 32-63 mm TWO-FLAT · 2014. 12. 17. · CYLINDERS SERIES “ISO 15552 (EX ISO 6431)” Ø 32-63 mm TYPE “A” RETRACTABLE SENSOR TWO FLAT
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1.1/89
1
CYLINDER SERIES ISO 15552(EX ISO 6431), Ø 32-63 mm TWO-FLAT
COMPONENTS
� PISTON ROD: stainless steel.� HEAD: die cast aluminium, fully machined� PISTON ROD GASKET: polyurethane� GUIDE BUSHING: sintered bronze� BARREL: drawn anodised calibrated aluminium� HALF-PISTON: self-lubricating technopolymer withbuilt-in cushioning olives� PISTON GASKET: Ø 32÷63 polyurethane MAGNET: plastoferrite Static O-rings: NBR� CUSHIONING GASKET: polyurethane� CUSHIONING NEEDLE: OT 58 with needle outmovement safety system even when fully open SCREWS: Tap Tite for assembly
4 1023 5 6 8 7 12111 9
This version of cylinder is used to keep the parts fixed to thepiston rod at an angle and to apply torques within thespecified limits.The piston rod of the Two Flat has two opposing longitudinalsurfaces; it is made of stainless steel.The front cylinder head includes a sintered bronze bush thatmatches the profile of the piston rod and prevents it fromrotating on its own axis. A special polyurethane gasketensures pneumatic seal and prevents the accumulation ofdirt. This technical solution is more reliable and gives a betterpneumatic seal than with square or hexagonal piston rods.The cylinders are made to ISO15552 standards. They areavailable in several versions and with a wide range ofaccessories:• with or without magnet• double acting, single piston rod• double acting, through rod; one piston rod is Two Flat,
the other cylindrical• fixing accessories.
POLYURETHANE
max 10 bar (max 1 MPa - 145 psi)–20 ÷+80 (non-magnetic cyl.)
–20 ÷+70 (magnetic cyl.))Unlubricated air. Lubrication, if used, must be continuous
Ø 32 ; Ø 40 ; Ø 50 ; Ø 63Heads with Tap Tite screws
Ø 32= 300 Ø 40= 400 Ø 50= 500 Ø63= 500� Maximum recommended strokes. Higher values can create operating problems
Double-acting cushioned, Through-rod cushioned, no-stick slip*All versions come complete with magnet. Supplied without magnet on request.
Ø 32= 0.70° Ø 40= 0.75° Ø 50= 0.65° Ø63= 0.65°See GENERAL TECHNICAL DATA PAGE 1.1/05See GENERAL TECHNICAL DATA PAGE 1.1/06
*Using for speeds lower than 0.2m/s, to prevent surging.For no-stick-slip versions use no-lubricated air only
TECHNICAL DATAOperating pressureTemperature range
°CFluidBoreDesignMaximun stroke � mm
VersionsSensor magnetInrush pressureMax torque on piston rod NmMaximum rotation on the rod degreesForces generated at 6 bar thrust/retractionWeights
1.1/90
DIMENSIONS OF STANDARD VERSIONS
1
0
121
120
CH1
B
E
CH
2
H
L +
L +
C 1
CF
M
N
E 1
L +
Q
D 2
GP
A 2
BD
A
A 1
G 1
E H
D 1
Ø.32405063
+ = ADD THE STROKE
A10121416
A1
791414
A2
10101010
B30354045
C26303737
C1
16202525
CH10131717
CH1
6688
DM10x1.25M12x1.25M16x1.5M16x1.5
D1
12162020
D2
15191923
E32.53846.556.5
E1
5555
F22243232
GG1/8G1/4G1/4G3/8
G1
M6M6M8M8
H47536575
L120135143158
L0
94105106121
L1
74817889
L2
146165180195
M991212
N4.54.55.55.5
P6666
Q4466
DIMENSIONS OF THROUGH-ROD VERSION
2
122
1CH
2
0
1
CH
E HC
HF
G 1
L +
L +
L ++
C +
D 2
G
QP
C 1M
N
D1
D
C F
A 2
B
A
A 1
E
H
D 1
+ = ADD THE STROKE++= ADD TWICE THE STROKE
CH2
10131717
1.1/91
1
INTERMEDIATE HINGE - MODEL EN
TL
X MIN
XV+1/2
X+ MAX
TK
TD
UW
TLTM
Code
0950322007095040200709505020070950632007
Ø
32405063
COUNTER-HINGE FOR MODEL EN - MODEL EL
A
H
B
A1 ±0.2
øL
E
C
C±
0.1
D1 D H7
D2
Cod.
W0950322009W0950402009W0950402009W0950632009
Ø
32405063
A
46555565
A1
32363642
B
18212123
C
30363640
C1
15181820
D2
79911
D
12161620
D1
11151518
E
6.58.58.510.5
+ = ADD THE STROKE+ 1/2 = ADD HALF THE STROKE
NOTE: Supplied with 4 securing screws
H
10.5121213
ØL
22282835
Weight [g]
2825828801230
Note: Supplied complete with 4 grub screws, 2 pins
Weight [g]
162278278414
ACCESSORIES: FIXINGS
KEY TO CODES
CYL 1 2 1
120 Double-acting,cuschioned,
non-magnetic121 Double-acting,
cushioned122 Through-rod
0
0 DiameterS Non-
magneticG No stick slip
3 2
32 40 50 63
0 0 5 0
� Ø32 stroke 0÷300 mm
� Ø40stroke 0÷400 mm
� Ø50÷Ø63stroke 0÷500 mm
F
F “Two Flat”piston rod
AISI 303stainless steel
nut
TYPE BORE STROKE
P
P polyurethanegaskets
� Maximum recommended strokes. Higher values can create operating problems
X (min)
63728386.5
XV
7382.59097.5
X (max)
839397108.5
TM
50637590
TL
12161620
TD e 9
12161620
TK
22283235
UW
657595105
1.1/92
KIT FOR FIXING VALVES TO BRACKETS
Code0950322090095040209009505020900950632090
ØØ 32Ø 40Ø 50Ø 63
A5459.571.581.5
B40404040
C29.532.23742
D110110110110
E64.567.27277
D124124124124
E70.573.27883
Applicable valvesMACH 16 Series 70 1/8-1/4 ISO 1 - ISO 2MACH 16 Series 70 1/8-1/4 ISO 1 - ISO 2MACH 16 Series 70 1/8-1/4 ISO 1 - ISO 2MACH 16 Series 70 1/8-1/4 ISO 1 - ISO 2
Composition2 HEX. SCREWS M3x25 with WASHER2 HEX. SCREWS M4x50 with WASHER2 HEX. SCREWS M5x50 with WASHERADAPTOR + ISO1 BASE SIDE + SCREWS + WASHERS (Fig. B)ADAPTOR + ISO 2 BASE SIDE + SCREWS + WASHERS (Fig. B)
CYLINDER BRACKET - VALVE SERIES KCV
B
A
C
D E
VALVE FIXING BRACKET - CYLINDER (Fig. A)
ISO 1 ISO 2
A B
VALVE ASSEMBLY ON CYLINDER
Weight [g)4820230350
Weight [g)808693101
1.1/93
1
ACCESSORIES: MAGNETIC SENSORS
9.1
11.5
25.534
17
SENSOR BRACKETS
SENSORCodeW0950000201W0950000222W0950000232
N.B.: for tecnical data on sensor, see page 1.1/71
DescriptionSENSOR REED DSM2-C525 HSSENSOR HALL PNP DSM3-N225SENSOR HALL NPN DSM3-M225
Ø 32÷40
13.2
2.7
18.5
M5
5.9
19.2
14
29.5 29.8
14.8 1.8
20.9
14
M5
20.4
1.6
25.9
Ø 50÷63
CodeW0950000711
DescriptionBRACKET ACC. D.32 DST 80
CodeW0950000712
DescriptionBRACKET ACC. D.50 DST 81
ADAPTOR FOR RETRACTABLE SENSOR
DescriptionAdaptor DSS005 for DST/ST brackets
CodeW0950001001
ASSEMBLY DIAGRAM
45
3
2 1
� ISO 15552 cylinder with traditional barrel� Sensor bracket mod. DST (Ø32÷125)� Adaptor� Retractable sensor with insertion from above� Retractable sensor
1.1/94
CYLINDERS SERIES “ISO 15552(EX ISO 6431)” Ø 32-63 mm TYPE “A”RETRACTABLE SENSOR TWO FLAT
JACKET CROSS SECTION
This version of cylinder is used to keep the parts fixed tothe piston rod at an angle and to apply torques within thespecified limits.Type A cylinders have a jacket with grooves for housingretractable sensors.The piston rod of the Two Flat has two opposing longitudinalsurfaces; it is made of stainless steel.The front cylinder head includes a sintered bronze bushthat matches the profile of the piston rod and prevents itfrom rotating on its own axis. A special polyurethane gasketensures pneumatic seal and prevents the accumulation ofdirt. This technical solution is more reliable and gives abetter pneumatic seal than with square or hexagonal pistonrods.The cylinders are made to ISO15552 standards. They areavailable in several versions and with a wide range ofaccessories:• with or without magnet• double acting, single piston rod• double acting, through rod; one piston rod is Two Flat,
the other cylindrical• fixing accessories.
TECHNICAL DATA POLYURETHANE
max 10 bar (max 1 MPa - 145 psi)–20 ÷+80 (non-magnetic cyl.)
–20 ÷+70 (magnetic cyl.))Unlubricated air. Lubrication, if used, must be continuous
Ø 32 ; Ø 40 ; Ø 50 ; Ø 63Heads with Tap Tite screws
Ø 32= 300 Ø 40= 400 Ø 50= 500 Ø63= 500� Maximum recommended strokes. Higher values can create operating problems
Double-acting cushioned, Through-rod cushioned, no-stick slip*All versions come complete with magnet. Supplied without magnet on request.
Ø 32= 0.70° Ø 40= 0.75° Ø 50= 0.65° Ø63= 0.65°See GENERAL TECHNICAL DATA PAGE 1.1/05See GENERAL TECHNICAL DATA PAGE 1.1/06
*For no-stick slip versions, use no-lubricated air only
Operating pressureTemperature range
°CFluidBoreDesignMaximun stroke � mm
VersionsSensor magnetInrush pressureMax torque on piston rod NmMaximum rotation on the rod degreesForces generated at 6 bar thrust/retractionWeights
1
Ø63
Ø32 Ø40
11
1
Ø50
31.9
74
31.9
74
44.5
13.3
44.5
6.6
53 18.4
53
18.4
63.3
23.5
23.5
63.3
� SLOTS FOR RETRACTABLE SENSOR
1.1/95
1DIMENSIONS OF STANDARD VERSIONS
1
0
121
CH1
B
E
CH
2
H
L +
L +
C 1
CF
M
N
E 1
L +
Q
D 2
GP
A 2
BD
A
A 1
G 1
E H
D 1
Ø32405063
+ = ADD THE STROKE
A10121416
A1
791414
A2
10101010
B30354045
C26303737
C1
16202525
CH10131717
CH1
6688
DM10x1.25M12x1.25M16x1.5M16x1.5
D1
12162020
D2
15191923
E32.53846.556.5
E1
5555
F22243232
GG1/8G1/4G1/4G3/8
G1
M6M6M8M8
H47536575
L120135143158
L0
94105106121
L1
74817889
L2
146165180195
M991212
N4.54.55.55.5
P6666
Q4466
DIMENSIONS OF THROUGH-ROD VERSION
2
122
1CH
2
0
1
CH
E HC
HF
G 1
L +
L ++
C +
D 2
G
QP
C 1M
N
D1
D
C F
A 2
B
A
A 1
E
H
D 1
L +
+ = ADD THE STROKE++= ADD TWICE THE STROKE
CH2
10131717
1.1/96
F “Two Flat”piston rod
AISI 303stainless steel
nut
P polyurethanegaskets
KEY TO CODES
CYL 1 2 1
121 Double-acting,cushioned
122 Through-rod
A StandardB No stick slipC Non-
magnetic
TYPE DIAMETER STROKE
3 2
32 40 50 63
0 0 5 0
� Ø32stroke 0÷300 mm
� Ø40stroke 0÷400 mm
� Ø50÷Ø63 stroke 0÷500 mm
F PA
� Maximum recommended strokes. Higher values can create operating problems
ACCESSORIES: FIXINGS
INTERMEDIATE HINGE - MODEL EN
UW
X+ MAX
TMTL
TL
TK TD
X MIN
XV+1/2
Code
0950322107095040210709505021070950632107
Ø
32405063
X (min)
63728386.5
XV
7382.59097.5
X (max)
839397108.5
TM
50637590
TL
12161620
COUNTER-HINGE FOR MODEL EN - MODEL EL
A
H
B
A1 ±0.2
øL
E
C
C±
0.1
D1 D H7
D2
Code
W0950322009W0950402009W0950402009W0950632009
Ø
32405063
A
46555565
TD e 9
12161620
TK
22282836
UW
657595105
A1
32363642
B
18212123
C
30363640
C1
15181820
D2
79911
D
12161620
D1
11151518
E
6.58.58.510.5
+ = ADD THE STROKE+ 1/2 = ADD HALF THE STROKE
Note: Supplied with 4 securing screws
H
10.5121213
ØL
22282835
Weight [g]
170360580950
Note: Supplied complete with 4 grub screws, 2 pins
Weight [g]
162278278414
1.1/97
1VALVE ASSEMBLY ON CYLINDER
With this type of cylinder, the valves (D) canbe mounted directly using the retractingsensor slot, without requiring the use ofintermediate brackets.This can be done using the special plates(A), which come with both the M3 and M4threads, and screws (B) of the size, typeand quantity shown in the table below.For ISO 1 and ISO 2 valves, the kit onwhich the valve is to be mounted (codesshown in the tables) will be fitted to thecylinder using the special plates (A) andthe screws (B) listed in the table.
(one per plate)M3x16 UNI 5931 (DIN 912)M4x25 UNI 5931 (DIN 912)M4x30 UNI 5931 (DIN 912)M4x45 UNI 5931 (DIN 912)M4x8 UNI 7688 (DIN 965A)M4x8 UNI 7688 (DIN 965A)
Washer (B)(one per screw)
A3.2 UNI 1751 (DIN 127A)–
A4.3 UNI 1751 (DIN 127A)A4.3 UNI 1751 (DIN 127A)
––
Valveassembly
kit––––
09500020010950002002
ABD
NOTE
1.1/98
ACCESSORIES: MAGNETIC SENSORS
RETRACTABLE SENSOR WITH INSERTIONFROM ABOVE Description
This type of sensor can be inserted in the slot of the sensor from above. This means thecylinder heads do not require a through opening.
WIRING DIAGRAM TECHNICAL DATA
Type of contactSwitchSupply voltage (Ub) VPower WVoltage variationVoltage drop VInput current mAOutput current mASwitching frequency HzShort-circuit protectionOver-voltage suppressionPolarity inversion protectionEMCLED displayMagnetic sensitivityRepeatabilityDegree of protection (EN 60529)Vibration and shock resistanceTemperature range °CSensor capsule material2.5m/2m connecting cableConnecting cable with M8x1Wire NO.
CYLINDERS ISO 15552 STD AND TYPE “A”RETRACTABLE SENSOR TWO-FLAT: SPARES
1
9
42
16
3
1817 19
51115 1213 10 7 8614
TypeComplete set of polyurethane gasketsComplete polyurethane front head kitComplete polyurethane rear head kitComplete polyurethane piston kitComplete polyurethane head A+P+piston kitMagnet