CY4531 EZ-PD TM CCG3 EVK QUICK START GUIDE STEP 2 Verify that the user LED jumper (J11) is populated on the CCG EVK base board. Verify that the VSYS selection jumper (J3) on the CCG3 daughter card is set to 3.3 V (position 1-2) and the IO Supply selection jumper (J4) is set to VDDD (position 2-3). Connect the DC power adapter (provided with the kit) to the DC power jack (J1) of the CCG base board. Plug the other end of the DC power adapter into an AC power socket. LED1 (Green) on the CCG3 daughter card and the CCG EVK base board turn ON to indicate that the kit is powered. In addition, LED2 (Orange) on the CCG EVK base board blinks continuously to indicate that CCG firmware is executing. J4 DisplayPort Connector J12 Variable Power Supply (Provider) Header J7 Consumer Power Output Header J7 USB 2.0 Mini-B Receptacle J4 IO Supply Selection Jumper 2-3 Short: Power from VDDD of CCG3 (Default Setting) J3 VSYS Selection Jumper 1-2 Short: 3.3V supply coming from CCG base board (Default Setting) J2 USB 3.0 Type-B Receptacle J3 USB Type-C Receptacle LED1 CCG EVK Base Board LED2 CCG EVK Base Board J1 24V DC Power Supply (Provider) Connector J9 Debug Connector Reset Switch CYPD3125-40LQXIT LED1 CY4531 CCG3 Daughter Card J11 LED Jumper CCG EVK Base Board CY4531 CCG3 Daughter Card USB 2.0 Type-A to Mini-B Cable USB 3.1 EMCA Type-C Cable USB 3.0 Type-A to Type-B Cable 24V DC Power Adapter USB Type-C to Type-A Adapter STEP 1 Unpack the kit contents
3
Embed
CY4531 EZ-PDTM CCG3 EVK - Mouser Electronics · CY4531 EZ-PDTM CCG3 EVK QUICK START GUIDE STEP 2 Verify that the user LED jumper (J11) is populated on the CCG EVK base board. Verify
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
CY4531 EZ-PDTM CCG3 EVK
QUICK START GUIDE
STEP
2
Verify that the user LED jumper (J11) is populated on the CCG EVK base board. Verify that the VSYSselection jumper (J3) on the CCG3 daughter card is set to 3.3 V (position 1-2) and the IO Supplyselection jumper (J4) is set to VDDD (position 2-3). Connect the DC power adapter (provided withthe kit) to the DC power jack (J1) of the CCG base board. Plug the other end of the DC poweradapter into an AC power socket. LED1 (Green) on the CCG3 daughter card and the CCG EVK baseboard turn ON to indicate that the kit is powered. In addition, LED2 (Orange) on the CCG EVK baseboard blinks continuously to indicate that CCG �rmware is executing.
J4 DisplayPort Connector
J12 Variable Power Supply(Provider) Header
J7 Consumer Power Output Header
J7 USB 2.0 Mini-B Receptacle
J4 IO Supply Selection Jumper2-3 Short: Power from VDDD of CCG3 (Default Setting)
Connect the USB 3.0 Type-A to Type-B cable from the PC to the USB Type-B receptacle (J2) of the CCG base board. Connect the USB Type-C to Type-A adapter to the USB Type-C receptacle (J3) of the CCG base board. Plug a USB �ash drive (not provided with the kit) into the USB Type-C to Type-A adapter.Verify your setup as shown in the picture below. Observe the enumeration of the USB �ash drive on the PC. Initiate data transfer between the PC and the �ash drive, and observe the data transfer speed*.
STEP
4
For more details, refer to the CY4531 Kit Guide.pdf** located atC:\Program Files (x86)\Cypress\CY4531 CCG3 EVK\1.0\Documentation on 64-bit Windowsoperating systems or C:\Program Files\Cypress\CY4531 CCG3 EVK\1.0\Documentation on32-bit Windows operating systems.
** Download and install the CY4531 CCG3 EVK setup �le from www.cypress.com/CY4531 to access the latest kit design �les and documentation
Note that any USB device can be used instead of a �ash drive with the setup shown in step 3.
* Data transfer speed depends on the type of the USB port (SuperSpeed or High Speed) of the PC, read/write speed of the �ash drive (SuperSpeed or High Speed) and the system con�guration. You can evaluate the reversibility of the Type-C interface by detaching the USB Type-C to Type-A adapter, reconnecting it in an upside-down orientation and observing its enumeration.