Chamfer Both Sides Alternating Chamfer Both Sides Triple Tooth Grind Radius Left Side Chamfer Right Side Radius Both Sides Full Radius Radius Right Side Chamfer Left Side Alternating Right Left Chamfer Chamfer Right Side Chamfer Left Side Radius Left Side Width Grind Radius Right Side CUSTOMIZED WIDTHS • RADIUS • CHAMFERS Carbide Tipped Milling Cutters & Slitting Saws 3” • 4” • 5” • 6” Diameters 2016
10
Embed
CUSTOMIZED WIDTHS • RADIUS • CHAMFERS · 2016. 3. 25. · Corner Radius or Chamfer on ONE Side Modified width between .0600” and .5312” Corner Radius or Chamfer on BOTH Sides
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
ChamferBoth Sides
Alternating Chamfer
Both Sides
Triple Tooth Grind
Radius Left Side Chamfer
Right Side
RadiusBoth Sides
Full Radius Radius Right Side Chamfer
Left Side
Alternating Right Left Chamfer
ChamferRight Side
ChamferLeft Side
RadiusLeft Side
WidthGrind
RadiusRight Side
CUSTOMIZEDWIDTHS • RADIUS • CHAMFERS
Carbide Tipped Milling Cutters & Slitting Saws
3” • 4” • 5” • 6” Diameters
2016
Corner Radius or Chamfer on ONE Side
Modified width between .0600” and .5312”
Corner Radius or Chamfer on BOTH Sides OR a Full Radius
HANNIBAL CARBIDE TOOL, INC. • TEL 800-451-9436 • FAX 800-633-7302 • [email protected]
TYPE 559Cutter Notes (All cutters on page)• 12 Teeth• C-2(m) Carbide• 5° Positve Radial Rake• Width Tolerance: +.001”/-.000”• OD tolerance: +.0313”/-.000”• 1” Arbor hole +.001”/-.000”• ANSI standard keyway dimensions• Add 5% to grind down hub width• Add 5% to match OD’s on cutter sets within .001”•Not designed to be used on heat treated materials greater than 363 Brinell (39Rc)
Radius Notes• Maximum radius on one side is .2656”• Full radius and maximum radius on both sides is 1/2 the width of the cutter• A non-tangent radii must be quotedChamfer Notes• Chamfer Angles can range from 0º to 45º• Chamfer is measured off the OD• Maximum chamfer is the LESSER of 1/3 the width of the cutter OR .2656” length of angle when measured across the OD• Chamfer Angle Tolerance: +/- 1/2º• Chamfers greater than 45º must be quoted
• Price Increases 5% for Alternating Chamfers
RadiusRight Side
RadiusLeft Side
ChamferLeft Side
ChamferRight Side
WidthGrind
Radius Right Side Chamfer
Left Side
Alternating Right Left Chamfer
ChamferBoth Sides
Triple Tooth Grind
Radius Left Side Chamfer
Right Side
Full RadiusRadiusBoth Sides
Alternating Chamfer
Both Sides
Specify right or left side for radius or chamfer
Corner Radius or Chamfer on ONE Side
Modified width between .0600” and .5312”
Corner Radius or Chamfer on BOTH Sides OR a Full Radius
HANNIBAL CARBIDE TOOL, INC. • TEL 800-451-9436 • FAX 800-633-7302 • [email protected]
TYPE 559 Cutter Notes (All cutters on page)• 14 Teeth• C-2(m) Carbide• 5° Positve Radial Rake• Width Tolerance: +.001”/-.000”• OD tolerance: +.0313”/-.000”• 1” Arbor hole +.001”/-.000”• ANSI standard keyway dimensions• Add 5% to grind down hub width• Add 5% to match OD’s on cutter sets within .001”•Not designed to be used on heat treated materials greater than 363 Brinell (39Rc)
Radius Notes• Maximum radius on one side is .2656”• Full radius and maximum radius on both sides is 1/2 the width of the cutter• A non-tangent radii must be quotedChamfer Notes• Chamfer Angles can range from 0º to 45º• Chamfer is measured off the OD• Maximum chamfer is the LESSER of 1/3 the width of the cutter OR .2656” length of angle when measured across the OD• Chamfer Angle Tolerance: +/- 1/2º• Chamfers greater than 45º must be quoted
• Price Increases 5% for Alternating Chamfers
RadiusRight Side
RadiusLeft Side
ChamferLeft Side
ChamferRight Side
WidthGrind
Radius Right Side Chamfer
Left Side
Alternating Right Left Chamfer
ChamferBoth Sides
Triple Tooth Grind
Radius Left Side Chamfer
Right Side
Full RadiusRadiusBoth Sides
Alternating Chamfer
Both Sides
Specify right or left side for radius or chamfer
Corner Radius or Chamfer on ONE Side
Modified width between .0704” and .5312”
Corner Radius or Chamfer on BOTH Sides OR a Full Radius
HANNIBAL CARBIDE TOOL, INC. • TEL 800-451-9436 • FAX 800-633-7302 • [email protected]
TYPE 559Cutter Notes (All cutters on page)• 16 Teeth• C-2(m) Carbide• 5° Positve Radial Rake• Width Tolerance: +.001”/-.000”• OD tolerance: +.0313”/-.000”• 1” Arbor hole +.001”/-.000”• ANSI standard keyway dimensions• Add 5% to grind down hub width• Add 5% to match OD’s on cutter sets within .001”•Not designed to be used on heat treated materials greater than 363 Brinell (39Rc)
Radius Notes• Maximum radius on one side is .2656”• Full radius and maximum radius on both sides is 1/2 the width of the cutter• A non-tangent radii must be quotedChamfer Notes• Chamfer Angles can range from 0º to 45º• Chamfer is measured off the OD• Maximum chamfer is the LESSER of 1/3 the width of the cutter OR .2656” length of angle when measured across the OD• Chamfer Angle Tolerance: +/- 1/2º• Chamfers greater than 45º must be quoted
• Price Increases 5% for Alternating Chamfers
RadiusRight Side
RadiusLeft Side
ChamferLeft Side
ChamferRight Side
WidthGrind
Radius Right Side Chamfer
Left Side
Alternating Right Left Chamfer
ChamferBoth Sides
Triple Tooth Grind
Radius Left Side Chamfer
Right Side
Full RadiusRadiusBoth Sides
Alternating Chamfer
Both Sides
Specify right or left side for radius or chamfer
Corner Radius or Chamfer on ONE Side
Modified width between .0704” and .5312”
Corner Radius or Chamfer on BOTH Sides OR a Full Radius
HANNIBAL CARBIDE TOOL, INC. • TEL 800-451-9436 • FAX 800-633-7302 • [email protected]
TYPE 559Cutter Notes (All cutters on page)• 18 Teeth• C-2(m) Carbide• 5° Positve Radial Rake• Width Tolerance: +.001”/-.000”• OD tolerance: +.0313”/-.000”• 1” Arbor hole +.001”/-.000”• ANSI standard keyway dimensions• Add 5% to grind down hub width• Add 5% to match OD’s on cutter sets within .001”•Not designed to be used on heat treated materials greater than 363 Brinell (39Rc)
Radius Notes• Maximum radius on one side is .2656”• Full radius and maximum radius on both sides is 1/2 the width of the cutter• A non-tangent radii must be quotedChamfer Notes• Chamfer Angles can range from 0º to 45º• Chamfer is measured off the OD• Maximum chamfer is the LESSER of 1/3 the width of the cutter OR .2656” length of angle when measured across the OD• Chamfer Angle Tolerance: +/- 1/2º• Chamfers greater than 45º must be quoted
• Price Increases 5% for Alternating Chamfers
RadiusRight Side
RadiusLeft Side
ChamferLeft Side
ChamferRight Side
WidthGrind
Radius Right Side Chamfer
Left Side
Alternating Right Left Chamfer
ChamferBoth Sides
Triple Tooth Grind
Radius Left Side Chamfer
Right Side
Full RadiusRadiusBoth Sides
Alternating Chamfer
Both Sides
Specify right or left side for radius or chamfer
MADE IN USA
WORLD CLASS
HANNIBAL CARBIDE TOOL, INC. • TEL 800-451-9436 • FAX 800-633-7302 • [email protected]
Corner Radius or Chamfer on ONE Side
Modified width between .0600” and .5312”
Corner Radius or Chamfer on BOTH Sides OR a Full Radius
TYPE 556Cutter Notes (All cutters on page)• 16 Teeth• C-5 Carbide• 1° - 3° Positve Radial Rake• Width Tolerance: +.001”/-.000”• OD tolerance: +.0313”/-.000”• 1” Arbor hole +.001”/-.000”• ANSI standard keyway dimensions• Add 5% to grind down hub width• Add 5% to match OD’s on cutter sets within .001”•Not designed to be used on heat treated materials greater than 475 Brinell (50Rc)
Radius Notes• Maximum radius on one side is .2656”• Full radius and maximum radius on both sides is 1/2 the width of the cutter• A non-tangent radii must be quotedChamfer Notes• Chamfer Angles can range from 0º to 45º• Chamfer is measured off the OD• Maximum chamfer is the LESSER of 1/3 the width of the cutter OR .2656” length of angle when measured across the OD• Chamfer Angle Tolerance: +/- 1/2º• Chamfers greater than 45º must be quoted
• Price Increases 5% for Alternating Chamfers
RadiusRight Side
RadiusLeft Side
ChamferLeft Side
ChamferRight Side
WidthGrind
Specify right or left side for radius or chamfer
Radius Right Side Chamfer
Left Side
Alternating Right Left Chamfer
ChamferBoth Sides
Triple Tooth Grind
Radius Left Side Chamfer
Right Side
Full RadiusRadiusBoth Sides
Alternating Chamfer
Both Sides
www.hannibalcarbide.com • TEL 573-221-2775 • FAX 573-221-1140 • HANNIBAL CARBIDE TOOL, INC.
MADE IN USA
WORLD CLASS
Corner Radius or Chamfer on ONE Side
Modified width between .0600” and .5312”
Corner Radius or Chamfer on BOTH Sides OR a Full Radius
TYPE 556Cutter Notes (All cutters on page)• 20 Teeth• C-5 Carbide• 1° - 3° Positve Radial Rake• Width Tolerance: +.001”/-.000”• OD tolerance: +.0313”/-.000”• 1” Arbor hole +.001”/-.000”• ANSI standard keyway dimensions• Add 5% to grind down hub width• Add 5% to match OD’s on cutter sets within .001”• Not designed to be used on heat treated materials greater than 475 Brinell (50Rc)
Radius Notes• Maximum radius on one side is .2656”• Full radius and maximum radius on both sides is 1/2 the width of the cutter• A non-tangent radii must be quotedChamfer Notes• Chamfer Angles can range from 0º to 45º• Chamfer is measured off the OD• Maximum chamfer is the LESSER of 1/3 the width of the cutter OR .2656” length of angle when measured across the OD• Chamfer Angle Tolerance: +/- 1/2º• Chamfers greater than 45º must be quoted
• Price Increases 5% for Alternating Chamfers
WidthGrind
Specify right or left side for radius or chamfer
Radius Right Side Chamfer
Left Side
Alternating Right Left Chamfer
ChamferBoth Sides
Triple Tooth Grind
Radius Left Side Chamfer
Right Side
Full RadiusRadiusBoth Sides
Alternating Chamfer
Both Sides
RadiusRight Side
RadiusLeft Side
ChamferLeft Side
ChamferRight Side
MADE IN USA
WORLD CLASS
HANNIBAL CARBIDE TOOL, INC. • TEL 800-451-9436 • FAX 800-633-7302 • [email protected]
Corner Radius or Chamfer on ONE Side
Modified width between .0704” and .5312”
Corner Radius or Chamfer on BOTH Sides OR a Full Radius
Radius Notes• Maximum radius on one side is .2656”• Full radius and maximum radius on both sides is 1/2 the width of the cutter• A non-tangent radii must be quotedChamfer Notes• Chamfer Angles can range from 0º to 45º• Chamfer is measured off the OD• Maximum chamfer is the LESSER of 1/3 the width of the cutter OR .2656” length of angle when measured across the OD• Chamfer Angle Tolerance: +/- 1/2º• Chamfers greater than 45º must be quoted
• Price Increases 5% for Alternating Chamfers
WidthGrind
Specify right or left side for radius or chamfer
Radius Right Side Chamfer
Left Side
Alternating Right Left Chamfer
ChamferBoth Sides
Triple Tooth Grind
Radius Left Side Chamfer
Right Side
Full RadiusRadiusBoth Sides
Alternating Chamfer
Both Sides
RadiusRight Side
RadiusLeft Side
ChamferLeft Side
ChamferRight Side
5” MILLING CUTTERS & SLITTING SAWSCARBIDE TIPPED TYPE 556 - FOR STEEL
FOR STEEL
TYPE 556Cutter Notes (All cutters on page)• 24 Teeth• C-5 Carbide• 1° - 3° Positve Radial Rake• Width Tolerance: +.001”/-.000”• OD tolerance: +.0313”/-.000”• 1” Arbor hole +.001”/-.000”• ANSI standard keyway dimensions• Add 5% to grind down hub width• Add 5% to match OD’s on cutter sets within .001”•Not designed to be used on heat treated materials greater than 475 Brinell (50Rc)
www.hannibalcarbide.com • TEL 573-221-2775 • FAX 573-221-1140 • HANNIBAL CARBIDE TOOL, INC.
MADE IN USA
WORLD CLASS
Corner Radius or Chamfer on ONE Side
Modified width between .0704” and .5312”
Corner Radius or Chamfer on BOTH Sides OR a Full Radius
Radius Notes• Maximum radius on one side is .2656”• Full radius and maximum radius on both sides is 1/2 the width of the cutter• A non-tangent radii must be quotedChamfer Notes• Chamfer Angles can range from 0º to 45º• Chamfer is measured off the OD• Maximum chamfer is the LESSER of 1/3 the width of the cutter OR .2656” length of angle when measured across the OD• Chamfer Angle Tolerance: +/- 1/2º• Chamfers greater than 45º must be quoted
• Price Increases 5% for Alternating Chamfers
Specify right or left side for radius or chamfer
6” MILLING CUTTERS & SLITTING SAWSCARBIDE TIPPED TYPE 556 - FOR STEEL
FOR STEEL
TYPE 556Cutter Notes (All cutters on page)• 28 Teeth• C-5 Carbide• 1° - 3° Positve Radial Rake• Width Tolerance: +.001”/-.000”• OD tolerance: +.0313”/-.000”• 1” Arbor hole +.001”/-.000”• ANSI standard keyway dimensions• Add 5% to grind down hub width• Add 5% to match OD’s on cutter sets within .001”• Not designed to be used on heat treated materials greater than 475 Brinell (50Rc)
WidthGrind
Radius Right Side Chamfer
Left Side
Alternating Right Left Chamfer
ChamferBoth Sides
Triple Tooth Grind
Radius Left Side Chamfer
Right Side
Full RadiusRadiusBoth Sides
Alternating Chamfer
Both Sides
RadiusRight Side
RadiusLeft Side
ChamferLeft Side
ChamferRight Side
CARBIDE TIPPED MILLING CUTTERS & SLITTING SAWS
HANNIBAL CARBIDE TOOL, INC. • TEL 800-451-9436 • FAX 800-633-7302 • [email protected]
MADE IN USA
WORLD CLASS
ORDERING INFORMATION
Alternating Right Left Chamfer
A°R
CLW
A°L
CR
Alternating Chamfer
Both Sides
A°L
CL
W
A°R
CR
Full Radius
WR=W/2
ChamferBoth Sides
W
A°RA°L
CR
CL
RadiusBoth Sides
RRRL
W
Radius Right Side Chamfer
Left Side
RR
W
CL
A°L
Radius Left Side Chamfer
Right Side
CR
WRL
A°R
Triple Tooth Grind
CL
W
A°R
ChamferRight Side
CRW
A°R
RadiusRight Side
RRW
RadiusLeft Side
RL W
WidthGrind
W
ChamferLeft Side
WCL
A°L
TECHNICAL INFORMATION
Cu
tter R
otation
Table Feed
Climb Milling
Cu
tter R
otation
Table Feed
Conventional Milling
TYPES OF MILLING: In conventional milling, the direction of cutter rotation is opposite to the direction of workpiece feed. The initial portion of the chip generated is very thin and gradually increases through the cutting cycle. The maximum cutting force is upward at the end of the cutting cycle.
In climb milling, the direction of the cutter rotation and the direction of workpiece feed are the same. The initial portion of the chip generated is thick and gradually thins through the cutting cycle, producing a better finish. The maximum cutting force is the initial downward thrust at the beginning of the cutting cycle.
1. Fill in applicable information 2. Circle grind style from diagrams 3. Forward to Hannibal using contact information below
Circle desired grind style
Name Distributor Purchase Order#
Ship to Address Phone Fax
Material Being Cut Quantity
EDP = (From charts on previous pages)
RL = Radius Left
RR = Radius Right
W = Width Special Hub Width (Add’l 5%)*
CL = Chamfer Length Left
CR = Chamfer Length Right
A°L = Angle Left
A°R = Angle Right
*Special hub widths must be smaller than nominal hub widths listed in the tables