CURRIES Tech Data Frame Section Revised open/sections... · ASSA ABLOY, the global leader in door opening solutions i Index Frame Technical Data August, 2017 DESCRIPTION PAGE(S) Anchors

CURRIES Tech DataFrame Section

Revised May, 2018

ASSA ABLOY, the global leader in door opening solutions

iIndex

Frame Technical Data

August, 2017

DESCRIPTION PAGE(S)

Anchors – Drywall FrameBase Anchor ..........................................................................................................................35Compression Anchor ........................................................................................................34, 36, 39Multipurpose Anchor Installation ............................................................................................17Steel Channel Anchor Installation ..........................................................................................126Security Anchor ......................................................................................................................34

Anchors – Flush Frame (Masonry)Ceiling Strut............................................................................................................................18Conduit Compatible..............................................................................................................75-76Electric Steel Channel ............................................................................................................14Existing Wall Anchors ........................................................................................................9, 11, 12Floor Anchor (Foot Clip) ..........................................................................................................6-7Loose Spline ..........................................................................................................................128Masonry Anchors ..................................................................................................................9-10Mullion Stirrup Anchor ............................................................................................................18Multipurpose Anchor ..............................................................................................................16Steel Channel Anchor ..........................................................................................................13-14Steel Channel Anchor Installation ..........................................................................................126Wire Truss Anchor ..................................................................................................................15Wood Stud Anchor ..................................................................................................................15

Borrowed Lite Frames ..............................................................................................................41-42 Cabinet Jamb Frames..................................................................................................................90 CCW Stick Length Components ..............................................................................................109-120 Communicating Frames/Mullion ..................................................................................................96

Curriseal Frames ......................................................................................................................92-93 Custom Frame Profiles ............................................................................................................121-122 Double Egress Frames ..............................................................................................................2, 107 Drywall Frames

Corner Detail........................................................................................................................32-33Installation..............................................................................................................................40Profiles ................................................................................................................................36-38Throat Filler ............................................................................................................................43

KD Frame Assembly Instructions ............................................................................................129-131 ElectroLynx System ....................................................................................................................138 Fabricaton Frame Corner Details

Cutting and Notching............................................................................................................27-31Field Splice ............................................................................................................................24Welded Corner Details..........................................................................................................19-23

Flush Masonry FramesCorner Details ........................................................................................................................1-3Profiles ..................................................................................................................................3-5


iiIndexFrame Technical Data

December, 2015

DESCRIPTION PAGE(S)

Grout Hole ...................................................................................................................................85 Hardware Locations .............................................................................................................................44-48 Preparations Automatic Flush Bolts ......................................................................................................87 Closer Preparations .......................................................................................................77-81 Coordinator Preparations ..................................................................................................84 Deadlock Strike Preparations ...........................................................................................67 Electric Strike Preparations ........................................................................................74, 88, 89 Lock .............................................................................................................................68-71 Exit Device Preparations Rim Exit ...........................................................................................................................73 Vertical Rod Exit ...............................................................................................................72 Flush Bolt Preparations ........................................................................................................86-87 Hinge Preparations 4-1/2” .............................................................................................................................50 5” ....................................................................................................................................51 Anchor Hinge Preparation.................................................................................................58 Continuous Hinge Preparation ..........................................................................................55 Electric Hinges ..............................................................................................................52, 57 Double Acting Hinges .......................................................................................................59 Full width Hinge Reinforcement ........................................................................................54 High Frequency Hinge Reinforcement ...............................................................................53 Pocket Pivot Preparation ..................................................................................................60 Security Hinge .................................................................................................................56 Mullion (Hardware Removable) ...............................................................................................83 Pivots ..................................................................................................................................63, 64 Strikes ...........................................................................................................................61, 65, 66, 70 Surface Bolt Preparation .........................................................................................................83 Hospital Stops .............................................................................................................................100 KD Frame Assembly Instructions .............................................................................................129-131 KD SideLight Frame ....................................................................................................................137 Lead Lined Frame Steel Channel ..................................................................................................19 Mullion Construction ..........................................................................................................................103 Removable Mullion Vertical / Horzontal ..............................................................................104-105 Pocket Door Frame ...................................................................................................................97-98 Rabbet Dimensions ......................................................................................................................49 Rescue Hardware ........................................................................................................................62 Rough Buck Frames.....................................................................................................................91 Security Sidelite Frames .............................................................................................................133 Silencers ....................................................................................................................................127 Slip-on Drywall Frames ...............................................................................................................135 Slip-on Hybrid Drywall Frames ....................................................................................................136 Spats ........................................................................................................................................99 Stainless Steel Frames .............................................................................................................25, 26 Mercury Therm Break Frame ..................................................................................................123, 124 Thermal Break Frames ...........................................................................................................101-102 Transom Frame Removable Panel Installation .............................................................................134 Wall construction Details Masonry ..................................................................................................................................8


1Flush Masonry KD Miter Corner Joint

Frame Technical DataMarch, 2015

L#8 SCREW (MS002485)(REQUIRED ON ALL FIRERATED KD FRAMES)

HEAD

JAMB

SPOT WELDS

BREAK –OFF TOOL

JAMB

JAMB

BEND TABS TOWARD WALL

HEAD

CORNER ASSEMBLY2” (50.8) HEAD

BREAK AWAYCORNER CLIP

2-7/16”(61.9)

1-13/16”(46)

USING THE BREAK-OFF TOOL, BENDCLIP BACK AND FORTH TOWARD OPPOSITE FACE OF FRAME.DO NOT BEND PAST THE OUTSIDE FACE TO AVOID DEFORMING THE FACE.

NOTE: USING PLIERS TO BREAK OFF THE CORNER CLIP MAY RESULT IN DAMAGE TO THE FACE OF FRAME


2Masonry KD 4” Face HeadFrame Technical Data

March, 2015

L

Masonry KD Double Egress Frame

L

#8 SCREW(REQUIRED ON ALL FIRERATED KD FRAMES)

HEAD FILLERCORNER CLIP



BEND TABSTOWARD WALL

* 5-3/4” (146.1) JAMB DEPTH HAS 7/16” (11.1) RETURN

4-3/4” - 14”(120.6) - (355.6)

1/2”*(12.7)

2-5/8”(66.7)

1-3/8”(34.9)

JAMBDEM

HEADGE 2-5/8”

(66.7)

4-3/4” - 14”(120.6) - (355.6)1/2”*

(12.7)

2”(50.8)


3Masonry KD “G” Profile - Corner Details

Frame Technical DataMarch, 2015

L

JAMBHEAD

CORNER ASSEMBLY

BEND TABSTOWARD WALL

Masonry KD 2” Face Flush Frame Unequal Rabbet

L1-15/16”(49.2)

VARIES 1-9/16”(39.7)

5/8”(15.9)

2”(50.8)

1/2”(12.7)

M

KD “M” TYPE FLUSHGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9)VARIABLE SOFFITJAMB DEPTH 4-1/2” (114.3) THRU 14” (355.6) (1/8”(3.2) INCREMENTS)AVAILABLE WITH 4” (101.6) FACE HEADSNOTE: 5-3/4” (146.1) JAMB DEPTH STANDARD WITH 7/16” (11.1) RETURNSTO PROVIDE 4-7/8” (123.8) THROAT OPENING



4Masonry 1", 1-1/4", 1-1/2", 1-3/4", Face Flush KD FrameUnequal RabbetFrame Technical DataApril, 2002

L1-15/16"(49.2)

VARIES 1-9/16"(39.7)

5/8"(15.9)

1" (25.4), 1-1/4" (31.8)1-1/2" (38.1), 1-3/4" (44.5)

1/2"(12.7)

KD “M” TYPE FLUSHGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9)VARIABLE SOFFITJAMB DEPTH 4-1/2" (114.3) THRU 14" (355.6) (1/8"(3.2) INCREMENTS)NOT AVAILABLE WITH 4" (101.6) FACE HEADS

NOTE: WHEN CCW MATERIAL IS USED IN CONJUNCTION WITH ABOVE, COORDINATE RABBET AND FACE DIMENSIONS 5-3/4" (146.1) JAMB DEPTH STANDARD WITH 7/16" (11.1) RETURNSTO PROVIDE 4-7/8" (123.8) THROAT OPENING.

M

Masonry Flush KD Frame Equal Rabbet

L VARIES

5/8"(15.9)

1" (25.4), 1-1/4" (31.8)1-1/2" (38.1), 1-3/4" (44.5)

2" (50.8)

1/2"(12.7)

M

1-15/16" (49.2)OR

1-9/16" (39.7)

1-15/16" (49.2)OR

1-9/16" (39.7)

KD “M” TYPE FLUSHGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9) VARIABLE SOFFITJAMB DEPTH 4-7/8" (114.3) THRU 14" (355.6) (1/8"(3.2) INCREMENTS)AVAILABLE WITH 4" (101.6) FACE HEADS WITH 2" FACE JAMBS ONLY

NOTE: WHEN CCW MATERIAL IS USED IN CONJUNCTION WITH ABOVE, COORDINATE RABBET AND FACE DIMENSIONS. 5-3/4" (146.1) JAMB DEPTH STANDARD WITH 7/16" (11.1) RETURNSTO PROVIDE 4-7/8" (123.8) THROAT OPENING.


5Masonry Face Flush KD Frame Cased Opening


April, 2002

LVARIES3" (76.2) MINIMUM

1" (25.4)1-1/4" (31.8)1-1/2" (30.1)1-3/4" (44.5)2" (50.8)

1/2"(12.7)

MK

KD “MK” TYPE FLUSHGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9)JAMB DEPTH 3" (76.2) THRU 14" (355.6) (1/8" (3.2) INCREMENTS)

NOTE: AVAILABLE WITH 4" (101.6) FACE HEAD WITH 4-1/2" (114.3) MINIMUM JAMB DEPTH 5-3/4" (146.1) JAMB DEPTH STANDARD WITH 7/16" (11.1) RETURNSTO PROVIDE 4-7/8" (123.8) THROAT OPENING.

Masonry Flush KD “G” Profile Frame

L

G

VARIES

2"(50.8)

1/2"(12.7)

1-15/16" (49.2)OR

1-9/16" (39.7)

5/8"(15.9)

2-5/8"(66.7)

KD “G” TYPE FLUSHGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9)JAMB DEPTH 3" (76.2) THRU 14" (355.6) (1/8" (3.2) INCREMENTS)MIN. 4" JAMB DEPTH FOR LABELED FRAME WITH 1-15/16" RABBET AND 3-1/4" JAMB DEPTH FOR 1-9/16" RABBET.

NOTE: 2" (50.8) AND 2-5/8" (66.7) FACE ON JAMBSAVAILABLE WITH 4" (101.6) FACE HEAD WITH 4-1/2" (114.3) MINIMUM JAMB DEPTH. 5-3/4" (146.1) JAMB DEPTH STANDARD WITH 7/16" (11.1) RETURNSTO PROVIDE 4-7/8" (123.8) THROAT OPENING.

*

* TOTAL DOOR ONLY MAY BE LABELED


6Standard Foot ClipsFrame Technical Data

April, 2002

L

2" (50.8)STANDARD

2" (50.8)

FACE MINUS 3/8" (9.5)LABEL REQUIREMENTS: FACE MINUS1/2" (12.7) MAXIMUM

9/32" (7.1) DIA.

P0030STANDARD FOOT CLIP16 GA. (1.4)

P0081DOUBLE EGRESSFOOT CLIPS

P0030C TYPE FRAME

FACE MINUS 3/8" (9.5)LABEL REQUIREMENTS: FACE MINUS1/2" (12.7) MAXIMUM

P0080G PROFILEJAMB DEPTH 4" (101.6) OR LESS

P0081G PROFILEGREATER THAN 4" (101.6) JAMB DEPTH

P0216 - 16 GA.FOR FACE WIDTH OVER 4"P0281 - 14 GA.P0284 - 12 GA.


7Adjustable Foot ClipFrame Technical Data

April, 2002

L

Adjustable Foot Clip - Cased Opening

L

FOOT CLIP SHIPPED LOOSE WITH 2-#12 SHEET METAL SCREWS

ANCHOR PART NUMBER: P0078

5/8" (15.7)3/4" (19.1)

16 GA. (1.4)

1/2" (12.7)

3-5/8" (92)

1/4" (6.4)4-5/8"

(117.5)

PER FACE DIMENSION16 GA. (1.4)

PER JAMB DEPTH

9/32" (7.1) DIA.

5/8" (15.7)3/4" (19.1)

16 GA. (1.4)

1/2" (12.7)

3-5/8" (92)

1/4" (6.4)4-5/8"

(117.5)

PER FACE DIMENSION16 GA. (1.4)

PER JAMB DEPTH

9/32" (7.1) DIA.

FOOT CLIP SHIPPED LOOSE WITH 2-#12 SHEET METAL SCREWS



8Common Walls For Masonry AnchorFrame Technical Data

April, 2002

L

BUTTED MASONRY-BRICK-TILE OR CMU

GROUT FULL

SHIM AS REQUIRED

GROUT OPTIONAL

EXISTING MASONRY OR POURED CONCRETE.

WRAP MASONRY-BRICK-TILE OR CMU




9Masonry Wire Anchor


April, 2002

L

Concealed Existing Opening Anchor

L

ANCHOR PART NUMBER: P0098ORDER CODE LOOSE: MW

WIRE DIA. 3/16" (4.8) GALV.ANCHOR MAY BE BENTTO SUIT JAMB DEPTH

9" (228.6)

5-5/8"(142.9)

1-7/8"(47.6)

1-1/16"(27)

COUNTERSINK HOLE FOR 3/8"(9.5) F.H. BOLT

9/16" (14.3) DIA.

ANCHOR PART NUMBER: CF004557100 ANCHORS W/PLASTIC PLUG

PLASTIC PLUG PART NUMBER: MS002600100 PLASTIC PLUGS

PLASTIC PLUG

3/4" (19.1) HOLE INCENTER OF SOFFIT

NOT DRILLED BY CURRIES

3/8" (9.5) BOLT & EXPANSION SHELL(NOT PROVIDED)

NOTE: ANCHORS AVAILABLE FOR 5-3/4" (146.1) JAMB DEPTH 2" FACE ONLY AVAILABLE AS SHIP LOOSE PART ONLY

2-1/2"(63.5)


10Masonry "T" AnchorFrame Technical Data

June, 2012

L

Weld in Type Masonry Anchor

L

ANCHOR PART NUMBER: P0069ORDER CODE LOOSE: M

10" (254.0)

2" (50.8)

16 GA. (1.4)

ANCHOR PART NUMBER: P0002ORDER CODE LOOSE: MLORDER CODE WELDED: WML

10-3/4" (273.1)

2" (50.8)

16 GA. (1.4)


11EWA Anchor


November, 2004

LFOR STANDARD RABBETED FRAMES 1-15/16" (49.2) X 1-9/16" (39.7)THE EWA ANCHOR IS AVAILABLE IN 5-1/2" (139.7) & 8-1/2" (215.9) SIZES TOFIT 5-3/4" (146.1) & 8-3/4" (222.3) STANDARD RABBETED FRAMES RESPECTIVELY.3/8" FLAT HEAD BOLT RECOMMENDED.

ANCHOR PART NUMBER: P0070ORDER CODE LOOSE: EWAORDER CODE WELDED: WEWA

-AVAILABLE AS SHIP-LOOSE ANCHOR-AVAILABLE FROM WAREHOUSE AS STOCK #CF004896-SPECIFY 5-1/2" (139.7) OR 8-1/2" (215.9) SIZE

1-1/2" MIN. 18, 16, 14 GA. (38.1)

MINIMUM

5-3/4" (146.1)8-3/4" (222.3)

ARCWELD

5-3/4" (146.1)8-3/4" (222.3)

5-1/2" (139.7)8-1/2" (215.9)

2-15/16" (74.6)4-7/16" (112.7)

2-9/16" (65.1)4-1/16" (103.2)

2-9/16"(65.1)

15/16"(23.8)

1" (25.4)

THE EWA ANCHOR MAY BE TRIMMED TO FIT ANY FRAME OF STANDARD RABBET OR SINGLE RABBET 8-3/4" (222.3) OR LESS IN JAMB DEPTHAND EQUAL RABBET 8-3/8" (212.7) OR LESS IN JAMB DEPTH

* 1-1/2" MINIMUM 12 GA.

NOTE: 1-7/8 MIN. STOP WIDTH FOR QM PROFILE

DIAMETER 3/8" (9.5) X 1-3/4" (44.5)EMBEDMENT LENGTH OR STEELEXPANSION SHELL OR 3/8" (9.5)FLATHEAD BOLT


12Pipe Spacer AnchorFrame Technical Data

April, 2002

L

Spacing Bracket Anchor

L

ANCHOR PART NUMBER: P0044ORDER CODE LOOSE: PSORDER CODE WELDED: WPS

NOTE: FACE DIMENSION FOR PROFILE MUST BE EQUAL

DIAMETER 3/8" (9.5) X 1-3/4" (44.5) EMBEDMENTLENGTH OR STEEL EXPANSION SHELL OR 3/8" (9.5) FLATHEAD BOLT

3/4" I.D.(19.1)

1"(25.4)

1-1/4" (31.7) MIN. 18, 16, 14 GA.*

COUNTERSUNK FLATHEAD BOLT

ARC WELD

ANCHOR PART NUMBER: P0146ORDER CODE LOOSE: SBORDER CODE WELDED: WSB

DIAMETER 3/8" (9.5) X 1-3/4" (44.5)EMBEDMENT LENGTH OR STEEL EXPANSION SHELL OR 3/8" (9.5) FLATHEAD BOLT

1-1/4" (31.7) MIN. 18, 16, 14 GA.*

COUNTERSUNK FLATHEAD BOLT

VARIES

1-13/64"(30.6)

1-13/64"(30.6)

1/2" (12.7) DIA.

16 GA. (1.4)

* 1-1/2" MIN. FOR 12GA.

* 1-1/2" MIN. FOR 12 GA.


13Steel Channel Anchor - Slip-In


November, 2014

LSTANDARD (FLUSH)

ORDER CODE LOOSE: SCF

OPTIONAL (RECESSED)

ORDER CODE LOOSE: SCR

DOUBLE

RABBET

SINGLE

RABBET/DE

NOTE: MINIMUM FACE OF 1-1/4" (31.8) REQUIRED FOR THIS ANCHOR TYPE


14Steel Channel Anchor-WeldedFrame Technical Data

November, 2014

L STANDARD (FLUSH)

ORDER CODE: WSCF

OPTIONAL (RECESSED)

ORDER CODE: WSCR

ELECTRICAL CONDUIT

(RECESSED)

ORDER CODE: ESCR

SINGLE

RABBET/DE

DOUBLE

RABBET

NOTE: FLUSH ANCHORS ALLOW FOR 3/4" (19) DRYWALL. NEED TO SPECIFY IF GREATER.

FLUSH ANCHORS CAN BE USED WITH ELECTRICAL CONDUIT.


15Wood Stud AnchorFrame Technical Data

January, 2017

L

Wood Stud Anchors - Double Egress

L

SLIP IN WOOD STUD ANCHOR - “M” SERIES FRAME ONLYORDER CODE LOOSE: WS “A” DIMENSIONSANCHOR PART NUMBER: P0152 - SPECIFY STUD WIDTH

WELD IN WOOD STUD ANCHOR ORDER CODE LOOSE: WWS “A” DIMENSIONSANCHOR PART NUMBER: P0148 - SPECIFY STUD WIDTH

1” (25.4)

A

9/64” (3.6) DIA.

16 GA. (1.4)

1” (25.4)

A

9/64” (3.6) DIA.

16 GA. (1.4)

1” (25.4)

A

9/64” (3.6) DIA.

16 GA. (1.4)

3-1/4” (82.6)

1” (25.4)

A

9/64” (3.6) DIA.

16 GA. (1.4)

SLIP IN WOOD STUD ANCHOR ORDER CODE LOOSE: WS “A” DIMENSIONSANCHOR PART NUMBER: P0152 - SPECIFY STUD WIDTH

WELD IN WOOD STUD ANCHOR ORDER CODE LOOSE: WWS “A” DIMENSIONSANCHOR PART NUMBER: P0148 - SPECIFY STUD WIDTH

NOTE: SPECIFY JAMB OR HEAD ANCHOR WHEN ORDERING.CURRIES WOOD STUD ANCHORS CAN BE USED WITH WOOD AND METAL STUDS.

BOTH ARE LABEL APPROVED.


16Adjustable Multipurpose AnchorFrame Technical Data

October, 2010

ANCHOR PART NUMBER: P0027ANCHOR CODE: AMP“A” DIMENSION = JAMB DEPTHS OF 4-3/8" (111.1) THRU 6-3/4" (171.5)2" (50.8) FACE FLUSH “M” SERIES OR DRYWALL “C” SERIESFIELD ADJUSTED TO JAMB DEPTH. AVAILABLE AS SHIP LOOSE PART ONLY

FOR USE AS:WOOD STUD ANCHORWIRE TRUSS ANCHORSTEEL CHANNEL ANCHOR

ANCHOR PART NUMBER: P0045ANCHOR CODE: MPJAMB DEPTHS OF 4-3/4" (120.7) THRU 9-3/4" (247.6)2" (50.8) FACE FLUSH “M” SERIES OR DRYWALL “C” SERIES2" (50.8) X 2-5/8" (66.67) “G” SERIES OR DRYWALL “CG” SERIES

Multipurpose Anchor

L

#12-24 X 1/2" (12.7)SLOTTED HEX WASHER HEAD

1/8" (3.2) DIA.

16 GA. (1.4)

A

BEND OR TRIM LEGS TO SUIT WALL CONDITIONS

BEND OR TRIM LEGS TO SUITWALL CONDITIONS

NUMBER OFSTIFFENERSDEPEND ONJAMB DEPTHS

5/32" (4) DIA.

18 GA. (1.4)

UNEQUAL RABBETS ONLY ON MASONRY WALLS


17Multipurpose Anchor Installation - Drywall Return Frame


November, 2004

L

2. INSERT ANCHOR INTO FRAME THROAT TILTED AT APPROXIMATELY A 50˚ ANGLE AS SHOWN IN DETAIL “B”.

3. THE ANCHOR MUST ALSO BE INSERTED AT APPROXIMATELY A 20˚ ANGLE FROM THE RABBETS OF THE FRAME AS SHOWN IN DETAIL “B”. THE FLANGES ON THE ANCHOR MUST CLEAR THE BACKBEND RETURNS.

4. TWIST THE ANCHOR INTO PLACE BY APPLYING PRESSURE IN THE OPPOSITE DIRECTIONS TO EACH SIDE OF THE ANCHOR AS SHOWN IN DETAIL “C”.

5. ONCE THE ANCHOR HAS SNAPPED INTO PLACE, DETAIL “D”, TURN IT UP INTO THE CORRECT POSITION AS SHOWN IN DETAIL “E” LEGS SHOULD BE BENT BACK TO THE ORIGINAL POSITION IF NECESSARY.

1. BEND LEGS OF ANCHOR 90˚ AS SHOWN IN DETAIL “A” (LEGS MAY HAVE TO BE BENT FURTHER IN LATER STEPS).

DETAIL “A”

DETAIL “B”

DETAIL “C”

DETAIL “D”

DETAIL “E”

50˚

20˚

PUSH

PUSH LIFT UP

P0045


18Ceiling Strut AnchorFrame Technical Data

September, 2005

L

Mullion Stirrup Anchor

L

ANCHOR PART NUMBER: P01594" (101.6)

1" (25.4)

3/8" (9.5) DIA.2 PLS.

VARIES

1/4" (6.4)

STRUT1/4" (6.4) X 1" (25.4) STEEL BAR1 REQ’D

WEDGES

1/4" (6.4)1/16" (1.6)

1-1/4" (31.8)WEDGE

1-1/8" (28.6)

VARIES

STRUT GUIDE16 GA. (1.4)2 REQ’D

1-1/8" (28.6)

1-9/16" (39.7)


DIMENSION “B” VARIES WITH FACE DIMENSION2" (50.8) FACE MULLION “B” EQUALS 1-1/2" (38.1)

B9/32" (7.1) DIA.

1-1/2" (38.1)

VARIES WITHJAMB DEPTH

12 GA. (2.6)FIELD INSTALL #8 SMSMINIMUM EACH FACE


19Steel Channel Anchor for Lead Lined Frames


November, 2014

L

CONTINUOUS WELD FACE SEAMGRIND AND FINISH SMOOTH BEND TABS TOWARD WALL

CONTINUOUS WELD JOINTSOF RABBET AND SOFFIT

WELD CODE: FW L

Full Weld KD

STANDARD (FLUSH)

WELD CODE: WSCF-LL

OPTIONAL (RECESSED)

WELD CODE: WSCR-LL


20Seam Weld Flush KDFrame Technical Data

February, 2013

L

Saw Miter Weld

L


CONTINUOUS WELD FACE SEAMGRIND AND FINISH SMOOTH

CONTINUOUS WELD INSIDE OF MITER

GRIND FACE AND FINISH SMOOTH

WELD CODE SW (KD)

GRIND FACE AND FINISH SMOOTH

TACK WELD RABBETAND SOFFIT

WELD CODE SMWWELD CODE SMT


21Saw Butt Weld


April, 2002

LWELD CODE BEW (<3) WELD CODE BET (<3)

WELD CODE SBW (>3) WELD CODE SBT (>3)


22Corner WeldsFrame Technical Data

July, 2003

LWELD CODE BEF 10


23Splice Joints


April, 2002

L

Saw Miter Only

LNOTE: PREPARED FOR DISTRIBUTOR WELDING

WELD CODE FSP WELD CODE WSP

WELD CODE SMO

WELD CODE EBE

EXACTNO NOTCH

WELD CODE SBE

EXACTNOTCH TOP JAMBS

NOTCH BOTH ENDS. (BLANK OR HEADS)

NOTE: FACTORY WELDED FRAMES EXCEEDING 9' X 14' WILL BE PROVIDEDWITH FIELD SPLICES


24Field Splice FramesFrame Technical Data

June, 2010

FRAMES FACTORY WELDED AT CURRIES:

PROVIDE FIELD SPLICES FOR FRAMES THAT EXCEED OVERALL SIZE SHOWN.

FRAMES FACTORY WELDED AT REGIONAL SERVICE CENTERS:

14'0"(4267)WIDTH

9'0" (2743)HEIGHT

9'0" (2743)WIDTH

14'0"(4267)HEIGHT

14'0"(4267)WIDTH

9'0" (2743)HEIGHT

9'0" (2743)WIDTH

14'0"(4267)HEIGHT


25Die Mitered Weld Stainless Steel


February, 2014

L

JAMB DEPTH

THROAT OPENING1" (25.4) LESS THANJAMB DEPTH

JAMBHEAD

304 OR 316 STAINLESS STEEL FINISH:2B MILL#4 BRUSHED SATIN#6 FINE SATIN#8 MIRRORXLB XL BLEND

FULL FACE WELD AND INTERMITTENT SOFFET AND RABBET WELDS

THROAT OPENING1" (25.4) LESS THANJAMB DEPTH

JAMB DEPTH


26Stainless Steel Sidelight FrameFrame Technical Data

February, 2014

L

VERTICAL MEMBERS BUTT AT SILL AND HEAD

JAMB DEPTH

WELDED

JAMB DEPTH

304 OR 316 STAINLESS STEEL FINISH:2B MILL#4 BRUSHED SATIN#6 FINE SATIN#8 MIRRORXLB XL BLEND


27Half Sidelite Window Option


July, 2003

OPTION BMOST COMMON

REMOVE BACKSIDEOF MULLION

L

OPTION AAS REQUIRED

L

SPLICE WELD SECTION TO MULLIONFILL AND GROUND SMOOTH,LABELED WHEN FULLY WELDED.

OPTION CAS REQUIRED

L

FILLER PLATEWITH STOP

NOTE: MAY BE LABELED WHEN PROPERLYWELDED.

EXPOSED SEAM UNLESS FACTORYWELDED SEAM


28Cut and Notch OptionsFrame Technical Data

April, 2002

L

CORNER: KD STANDARD WHEN POSSIBLEMUST MEET KD PARAMETERS

SAW MITER:* IF FACES OF HEAD AND JAMB ARE EQUAL

1. EXCEPT: 4" (101.6) FACE HEAD TO2" (50.8) FACE JAMB

BUTT END:* IF FACES ARE UNEQUAL

* SMO OR SBE MUST BE NOTED IN CONSTRUCTION COLUMN.

NOTE: MAY BE LABELED WHEN PROPERLY WELDED

NOTE: MAY BE LABELED WHEN FACE WELDED

SAW MITER

BUTT END

KD


29Cut and Notch Options


April, 2002

L

STRIKE MULLION: NOTCH TOPEXCEPTION: WILL RUN THROUGH HEAD IF HEAD PROFILE IS

DIFFERENT ON GLASS SIDEEXAMPLE: “M” PROFILE AT DOOR OPENING

“G” PROFILE AT WINDOW SIDERUN MULLION THROUGH IF HEAD FACES ARE DIFFERENT FROM DOOR SIDE TO GLASS SIDEOR IF FIELD SPLICE IS REQUIRED


NOTE: PROVIDES ACCESS FOR ELECTRICAL CONDUIT OR GROUT


30Cut and Notch OptionsFrame Technical Data

April, 2002

L

HORIZONTAL MULLION: NOTCH BOTH ENDS TO BUTTBETWEEN VERTICAL MEMBERSIS STANDARD PREPARATION


NOTCH STOP OFJAMB TO RECEIVE MULLION

TYPICAL REMOVABLEMULLION PREPARATION

OPTIONAL STANDARD


31Cut and Notch Options


April, 2002

L

MULLION:NOTCH TOP AND BOTTOM, WILLRUN THROUGH FROM HEAD TOTOP OF SILL

1. EXCEPTION: WILL RUN MULLIONTHROUGH TO FLOOR RATHER THANSPLICE 2 SECTIONS OF SILL TOGETHER

2. EXCEPTION: RUN MULLION THROUGH HEAD AND SILL IF FIELD SPLICEIS REQUIRED

NOTE: MAY BY LABELED WHEN PROPERLY WELDED

SILLS:NOTCH BOTH ENDS TO BUTT BETWEENVERTICAL MEMBERS

OPTIONALSTANDARD STANDARD


32Saw Butt EndFrame Technical Data

June, 2009

L

Drywall KD “CG” Profile Corner Details


#8 SCREW (MS002485)(REQUIRED ON ALL FIRE RATED FRAMES)

L

WALL NOTCH JAMB FOR DRYWALL WALL CONSTRUCTION

OPTIONAL STANDARD


33Drywall KD Frame Corner Clip Detail


June, 2009

L

3-1/2" (88.9)

JAMB

HEAD2" FACE

2-3/8" (60.3)

2-3/8" (60.3)

#8 SCREW (MS002485)(REQUIRED ON ALLFIRE RATED FRAMES)

HEAD2" (50.8) FACE

SPOT WELDSBY CURRIES

*RETURN FILLER: P0071

HEAD4" (101.6) FACE

JAMB

WELDPROJECTIONS

C PROFILE CORNER


34Security AnchorFrame Technical Data

April, 2002

L

Drywall Frame Compression Anchor

L

COMPRESSIONANCHOR

SECURITYANCHOR

45" (1143) TYPICAL

BOTTOM OF FRAME

PER JAMBDEPTH

VARIES

1-1/8" (28.6)

1-1/8" (28.6)

3-1/2" (88.9)16 GA. (1.4)


5/8" (15.8)MAXIMUM TRAVEL

ANCHOR PART NUMBER: P0026 (2" FACE)ANCHOR PART NUMBER: P0018 (1-1/2" TO 1-3/4" FACE)

COMPRESSIONANCHOR

3-1/2" (88.9)1" (25.4)MIN.


35Drywall KD Frame Standard Base Anchor


November, 2004

L

Drywall KD Frame Optional Base Anchor

L

3/4" (19.1)

5/8" (15.9)

2" (50.8)

ANCHOR HOLESCOUNTERSUNK

#6 SCREWBOTH SIDES

3-1/4" (82.6)

1" (25.4)

7/8" (22.2)

1/2" (12.7)

1/2" (12.7)

3/16" (4.8) DIA.

16 GA. (1.4)


NOTE: REQUIRED ON 1-1/2" (38.1), 1-3/4" (44.5) FACE DRYWALL FRAMES. 3", 3-1/8", 3-1/4", JAMB DEPTHS.

2" FACEONLY

3/4" (19)

FLOOR

CL

MINIMUM JAMB DEPTH 3-3/8 (85.7)


36Drywall CG ProfilesFrame Technical Data

April, 2002

L

Compression Anchor System Narrow Jamb Depth

L

3" (76.2) – 14" (355.6)

VARIES1-15/16" (49.2)

OR1-9/16" (39.7)

JAMB DEPTHS

2-5/8" (66.7)2" (50.8)

5/8" (25.9)

1/2" (12.7)

3/8" (9.5)

1/2" (12.7)

3/8" (9.5)

GAUGE - 18 GA. (1.2), 16 GA. (1.4)

NOTE: AVAILABLE WITH 4" (101.6) FACE HEAD WITH 4-1/2" (114.3) MINIMUM JAMB DEPTH

CG PROFILE *1-3/8" (34.9) DOOR - 3" (76.2) JAMB DEPTH1-3/4" (44.5) DOOR - 3" (76.2), 3-1/8" (79.4), 3-1/4" (82.6), 3-3/8" (85.7) JAMB DEPTH

ROUGH OPENING WIDTHEQUALS NOMINAL DOOROPENING: PLUS 2-13/16" (71.4)

ROUGH OPENING HEIGHTEQUALS NOMINAL DOOROPENING: PLUS 3/4" - 1" MAX

(19.1) - (25.4)

STRAP BASE ANCHOR

3/4" (19.1)

-COMPRESSION ANCHORS 3-1/2" (88.9)CL

STROKE

* “CG” PROFILE JAMB DEPTHS NOT LISTED ABOVE USE STD. DRYWALL ROUGH OPENING DIMENSIONS

CG


37Drywall KD Frame Unequal Rabbet


April, 2002

L

Drywall KD Frame Equal Rabbet

L

1-1/2" (38.1)1-3/4" (44.5)2" (50.8)

5/8" (15.9)

1-15/16"(49.2)

1-9/16"(39.7)

VARIES

3/8" (9.5)

1/2"(12.7)

KD DRYWALLGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9) *UNEQUAL RABBETJAMB DEPTH 4-1/2" (114.3) THRU 14" (355.6) (1/8" (3.2) INCREMENTS)2" (50.8) FACE AVAILABLE WITH 4" (101.6) HEADS

NOTE: 14 GA. AVAILABLE WITH 2" (50.8) FACE ONLY

1-1/2" (38.1)1-3/4" (44.5)2" (50.8)

5/8" (15.9)

1-15/16" (49.2)OR

1-9/16" (39.7)VARIES

3/8" (9.5)

1/2"(12.7)

1-15/16" (49.2)OR

1-9/16" (39.7)OR OR

C

C

KD DRYWALLGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9) *UNEQUAL RABBETJAMB DEPTH 4-7/8" (123.8) THRU 14" (355.6) (1/8" (3.2) INCREMENTS)2" (50.8) FACE AVAILABLE WITH 4" (101.6) HEADSAVAILABLE IN COMMUNICATING FRAMES

NOTE: 14 GA. AVAILABLE WITH 2" (50.8) FACE ONLY


38Drywall KD Frame Cased OpeningFrame Technical Data

April, 2002

L

Drywall KD “CG” Profile Frame

L

VARIES3" (76.2) MINIMUM

1-1/2" (38.1)1-3/4" (44.45)

2" (50.8)

3/8" (9.5)

1/2" (12.7)

KD DRYWALLGAUGE - 18 GA. (1.2), 16 GA. (1.4), 14 GA. (1.9)JAMB DEPTH 3" (76.2) THRU 14" (355.6) (1/8" (3.2) INCREMENTS)14 GA. AVAILABLE W/2" FACE ONLY

NOTE: AVAILABLE WITH 4" (101.6) FACE HEAD WITH 4-1/2" (114.3) MINIMUM JAMB DEPTH WITH 2" FACE JAMBS ONLY.

VARIES

2" (50.8)

3/8" (9.5)

1/2" (12.7)

1-15/16" (49.2)

1-9/16" (39.7)OR

5/8" (50.8)

2-5/8" (66.7)

KD “CG” PROFILE DRYWALLGAUGE - 18 GA. (1.2), 16 GA. (1.4)JAMB DEPTH 3" (76.2) THRU 14" (355.6) (1/8" (3.2) INCREMENTS)

NOTE: 2" (50.8) AND 2-5/8" (66.7) FACE ONLY

CK

CG


39Drywall Cased Opening Compression Anchor


April, 2013

L

CM Profile Frames

L

2" (50.8) LEG

STIFFENER PART NUMBER: P0093

16 GA. (1.4)

VARIES2" (50.8)

3/4" (19.1)

NOTE: STIFFENER ADDED TO PREVENT DISTORTION OF FRAME WHEN TIGHTENING ANCHOR

FOOTCLIPS

CM 3-1/2" (88.9) - 14" (355.6)CMG 3" (76.2) - 14" (355.6)

2" (50.8) CM CMG

CM PROFILE FRAMES DO NOT HAVE THE COMPRESSION BAR NOR BASE ANCHORS.THEY DO HAVE FOOTCLIPS WELDED IN AND ARE FURNISHED WITH LOOSE DRY-WALL ANCHORS, WELDED IN ANCHORS ARE OPTIONAL. SAME K.D. CORNER CAPABILITIES AS THE C FRAME.

3/8" (9.5)

1/2" (12.7)


40Drywall KD Frame ("C" Profile) Installation InstructionsFrame Technical Data

July, 2009

4

5

3

68 7 8

9

10

1. CONSTRUCT WALL WITH ROUGH OPENING HEIGHT EQUAL TO FINISHED OPENING HEIGHT PLUS 3/4" (19.1) TO 1" (25.4) MAX., ROUGH OPENING WIDTH IS AS FOLLOWS: A) FOR 2" (50.8) FACE FRAMES-OPENING WIDTH PLUS 2-1/8" (54.0) TO 2-3/8" (60.3) B) FOR 1-3/4" (44.5) AND 1-1/2" (38.1) FACE FRAMES-OPENING WIDTH PLUS 2" (50.8) C) FOR “C” AND “CG” PROFILES, 3" (76.2) JAMB DEPTH 1-9/16" (39.7) RABBET AND 3" (76.2), 3-1/8" (79.4), 3-1/4" (82.6) AND 3-3/8" (85.7) JAMB DEPTH 1-15/16" (49.2) RABBET FRAMES-OPENING WIDTH PLUS 2-13/16" (71.4), ALL OTHER “C” AND “CG” PROFILE FRAMES-OPENING WIDTH PLUS 2-1/8" (54.0) TO 2-3/8" (60.3) d) FOR 2" (508) FACE CASED OPENING - OPENING WIDTH PLUS 2-1/4" (572)

2. BOTTOM OF FRAME MUST SET ON A SOLID SURFACE.

3. IF WRAP-AROUND BASE ANCHOR IS USED, NOTCH DRYWALL IN THAT AREA.

4. RETRACT COMPRESSION BARS IN THE JAMBS BY TURNING SCREWS COUNTER CLOCKWISE AND INSTALL ONE JAMB IN POSITION ON WALL.

5. INSERT FRAME HEAD UNDER THE CORNER CLIPS OF THE JAMB AND RAISE INTO POSITION.

6. INSERT THE CORNER CLIPS OF THE REMAINING JAMB INTO THE OPPOSITE END OF THE HEAD AND POSITION JAMB ON WALL.

7. LOCATE A REMOVABLE FRAME SPACING BAR AT BASE OF CENTERED FRAME TO MAINTAIN PROPER OPENING WIDTH DURING INSTALLATION.

8. LEVEL, SQUARE AND PLUMB FRAME AND INSTALL BASE ANCHOR SCREWS THROUGH COUNTERSINK HOLES IN FRAME FACE AND INTO FLOOR PLATE.

9. SQUARE TOP OF FRAME AND TIGHTEN COMPRESSION BARS BY TURNING SCREWS CLOCKWISE. (DO NOT OVERTIGHTEN).

10. INSTALL (4) NO. 8 X 1/2" (12.7) SHEET METAL SCREWS AT THE CORNERS OF THE HEAD TO ATTACH HEAD TO JAMBS (REQUIRED FOR FIRE RATED FRAMES).

L

2


41Drywall KD Borrowed Lite


July, 2007

L

OVERALL FRAMEWIDTH

NOTE A: ROUGH OPENING HEIGHT FOR 2" (50.8) FACE FRAMES EQUALS GLASS OPENING SIZE PLUS 2-1/2" (63.5) INCLUDING CASED OPENING NOTE A: ROUGH OPENING HEIGHT FOR 1-1/2" (38.1) & 1-3/4" (44.5) FACE FRAMES EQUALS GLASS OPENING SIZE PLUS 2" (50.8)NOTE B: ROUGH OPENING WIDTH FOR 2" (50.8) FACE FRAMES EQUALS GLASS OPENING SIZE PLUS 2-1/2" (63.5) INCLUDING CASED OPENING ROUGH OPENING WIDTH FOR 1-1/2" (38.1) & 1-3/4" (44.5) FACE FRAMES EQUALS GLASS OPENING SIZE PLUS 2" (50.8)

NOTE:

5/8" (15.8) X 5/8" (15.8) GLASS STOPSARE PUNCHED AND CUT TO LENGTH REMOVABLE STOPS MATCH FIXED STOPLENGTH AND ARE SHIPPED LOOSE

KD BORROWED LITE (DRYWALL FRAME ONLY)ORDER OF INSTALLATION - A) PLACE RIGHT SIDE VERTICAL JAMB MEMBER INTO OPENING; B) INSTALL SILL MEMBER AND ASSEMBLE COR-NER #1; C) THEN INSTALL HEAD MEMBER AND ASSEMBLE CORNER #2 D) WHILE INSTALLING THE REMAINING LEFT VERTICAL JAMB MEMBERIT MAY BE NECESSARY TO EXTEND THE HEAD (CORNER #3) AND SILL (CORNER #4) TO THEIR ROUGH OPENING LIMITATIONS FOR EASIER IN-STALLATION; E) THEN ASSEMBLE CORNER #3 AND FINALLY SNAP INTO POSITION THE REMAINING CORNER #4; F) INSTALL SCREWSTHROUGH FRAME RETURNS INTO CORNER CLIPS; G) ADJUST COMPRESSION BARS UNTIL LEVEL AND PLUMB.

GLASS OPENING1'6" (457.2) MINIMUM

ROUGH OPENINGHEIGHT

SEE NOTE A

OVERALL FRAMEHEIGHT

GLASSOPENING

VARIABLEFACE

ROUGH OPENING WIDTHSEE NOTE B

CL

CL

COMP.BAR

STD.

CL

CL

COMP.BAR

STD.

33

44 1

1

22

4" (101.6) FACE HEADS & SILLSARE NOT AVAILABLE.

“CG” PROFILE - SEE NEXT PAGE

VARIABLEFACE


42Single Rabbet Drywall KD Borrowed LiteFrame Technical Data

July, 2007

L

OVERALL FRAMEWIDTH

“CG” PROFILE - COMPRESSION BAR RABBET MOUNTED.

JAMB DEPTHS INCLUDE 3" (76.2), 3-1/8" (79.4), 3-1/4" (82.5), 3-3/8" (85.7) X 1-15/16" (49.2) RABBETAND 3" (76.2) X 1-9/16" (39.7) RABBET

NOTE A: ROUGH OPENING HEIGHT FOR 2" (50.8) FACE FRAMES EQUALS GLASS OPENING SIZE PLUS 2-3/4" (69.8)NOTE B: ROUGH OPENING WIDTH FOR 2" (50.8) FACE FRAMES EQUALS GLASS OPENING SIZE PLUS 2-1/2" (63.5)

KD BORROWED LITE (DRYWALL FRAME ONLY)ORDER OF INSTALLATION - A) PLACE RIGHT SIDE VERTICAL JAMB MEMBER INTO OPENING; B) INSTALL SILL MEMBER AND ASSEMBLE COR-NER #1; C) THEN INSTALL HEAD MEMBER AND ASSEMBLE CORNER #2 D) WHILE INSTALLING THE REMAINING LEFT VERTICAL JAMB MEMBERIT MAY BE NECESSARY TO EXTEND THE HEAD (CORNER #3) AND SILL (CORNER #4) TO THEIR ROUGH OPENING LIMITATIONS FOR EASIER IN-STALLATION; E) THEN ASSEMBLE CORNER #3 AND FINALLY SNAP INTO POSITION THE REMAINING CORNER #4; F) INSTALL SCREWSTHROUGH FRAME RETURNS INTO CORNER CLIPS. G) ADJUST COMPRESSION BARS UNTIL LEVEL AND PLUMB.

GLASS OPENING1'6" (457.2) MINIMUM

HEIGHTWIDTH

SEE NOTE A

OVERALL FRAMEHEIGHT

GLASSOPENING

VARIABLEFACE

ROUGH OPENING WIDTHSEE NOTE B

CL

CL

COMP.BAR

CL

CL

COMP.BAR

33

44 1

1

22

4"(101.6)

4"(101.6) #8 SHEET

METAL SCREW(8 PLACES)

VARIABLEFACE


43Throat Filler for Drywall Frames


April, 2002

L

INSTALLATION

1. FOR BEST RESULTS INSTALL FRAME IN OPENING FIRST. DO NOT TIGHTEN COMPRESSION ANCHORS.

2. CUT JAMB FILLER STRIPS TO OVERALL LENGTH OF JAMB BACKBEND. CUT HEAD FILLER STRIP 1" (25.4) UNDER OVERALL LENGTH OF HEAD BACKBEND.

3. REMOVE PROTECTIVE FILM FROM ADHESIVE TAPE AND APPLY FILLER STRIPS TO FRAME BACKBENDS WITH 1/8" (3.2) THICK LEG BETWEEN BACKBEND RETURN AND WALL. APPLY PRESSURE TO SEAT FIRMLY.

4. SQUARE FRAME, TIGHTEN COMPRESSION ANCHORS, INSTALL BASE ANCHORS AND RESEAT FILLER STRIPS IF NECESSARY.

FILLER EQUALS OVERALL LENGTH OF BACKBEND

1/2"(12.7)

1/2"(12.7)LENGTH OF

HEAD FILLER

OVERALL LENGTH OF HEAD BACKBEND

THROAT FILLER STRIPS ARE MADE OF WHITE RIGID PVC WITH RESILIENT DOUBLE FACE TAPE FOR APPLICATION TO THE FRAME BACKBEND OR AFTER THEFRAME HAS BEEN INSTALLED.

SUPPLIED IN LENGTHS OF 7 FT. 3 IN. (2209.8) TO ACCOMMODATE MOST JAMB HEIGHTS WITH A CONTINUOUS STRIP.

NOTE: THROAT FILLER IS NOT ALLOWED ON LABEL FRAMES

THROAT REDUCEDBY 1/8" (3.2)

ONE FILLER STRIP

THROAT REDUCEDBY 1/4" (6.4)

TWO FILLER STRIPS

1/8" (3.2)DOUBLE FACE TAPE

FULL SIZE


44CURRIES Standard Hinge & Strike Locations for 1-3/4" FramesFrame Technical Data

September, 2013

L

* STRIKE BACKSET: 5/16" (7.9) FOR 1-3/4" (44.5) DOOR1/2" (12.7) FOR 2" (50.8) DOOR

CL

CL

CL

CL

A

B

B

C

40" (1016) STANDARD

HINGE SIZE MAY VARY LOCATION REMAINS THE SAMEHINGE BACKSET: 5/16" (7.9) FOR 1-3/4" (44.5) DOOR 5/8" (15.9) FOR 2" (50.8) DOOR 5/8" (15.9) FOR 2-1/4" (57.2) DOORDOOR RABBETS: 1-15/16" (49.2) FOR 1-3/4" (44.5) DOOR 2-3/16" (55.6) FOR 2" (50.8) DOOR

FOR USE WITH THREE HINGES

4-1/2" (114.3) OR 5" (127)

*

4-7/8" (123.8)STRIKE

SIZE A B C

6’8” (2032) 7-1/4” (184.2) 30-1/4” (768.4) 12-1/4” (311.2) 6’10” (2082.8) 7-1/4” (184.2) 31-1/4” (793.8) 12-1/4” (311.2) 7’0” (2133.6) 7-1/4” (184.2) 32-1/4” (819.2) 12-1/4” (311.2) 7’2” (2184.4) 7-1/4” (184.2) 33-1/4” (844.6) 12-1/4” (311.2) 7’10” (2387.6) 7-1/4” (184.2) 37-1/4” (946.2) 12-1/4” (311.2) 8’0” (2438.4) 7-1/4” (184.2) 38-1/4” (971.6) 12-1/4” (311.2)

L

L

L

L

L

CL

NOTE: FOR FRAMES UNDER 60" TALL WEWILL CENTER THE STRIKE FOR ALLMANUFACTURERS LOCATIONS UNLESSNOTED OTHERWISE ON THE ORDER.


45CURRIES Standard Hinge & Strike Locations for 1-3/4" Frames


September, 2013

L

SIZE A B C

6'8" (2032) 7-1/4" (184.2) 20-1/8" (511.2) 12-3/8" (314.3) 6'10" (2082.8) 7-1/4" (184.2) 20-7/8" (530.2) 12-1/8" (308) 7'0" (2133.6) 7-1/4" (184.2) 21-1/2" (546.1) 12-1/4" (311.2) 7'2" (2184.4) 7-1/4" (184.2) 22-1/8" (562) 12-3/8" (314.3) 7'10" (2387.6) 7-1/4" (184.2) 24-7/8" (631.8) 12-1/8" (308) 8'0" (2438.4) 7-1/4" (184.2) 25-1/2" (647.7) 12-1/4" (311.2) 9'0" (2743.2) 7-1/4" (184.2) 29-1/2" (749.3) 12-1/4" (311.2) 10'0" (3048) 7-1/4" (184.2) 33-1/2" (850.9) 12-1/4" (311.2)

L

L

L

L

L

L

L

* STRIKE BACKSET: 5/16" (7.9) FOR 1-3/4" (44.5) DOOR1/2" (12.7) FOR 2" (50.8) DOOR

CL

CL

CL

CL

CL

A

B

B

C

40" (1016) STANDARD

HINGE SIZE MAY VARY LOCATION REMAINS THE SAME.HINGE BACKSET: 5/16" (7.9) FOR 1-3/4" (44.5) DOOR. 5/8" (15.9) FOR 2" (50.8) DOORDOOR RABBETS: 1-15/16" (49.2) FOR 1-3/4" (44.5) DOOR. 2-3/16" (55.6) FOR 2" (50.8) DOOR.

FOR USE WITH FOUR HINGES

4-1/2" (114.3) OR 5" (127)

*

4-7/8" (123.8)STRIKE

B

CL



46CURRIES Standard Hinge & Strike Locations for 1-3/8" FramesFrame Technical Data

September, 2013

L

SIZE A B C

6'8" (2032) 9-3/4" (247.7) 59-7/8" (1520.8) 10-3/8" (263.5)6'10" (2082.8) 9-3/4" (247.7) 61-7/8" (1571.6) 10-3/8" (263.5)7'0" (2133.6) 9-3/4" (247.7) 63-7/8" (1622.4) 10-3/8" (263.5)7'2" (2184.4) 9-3/4" (247.7) 65-7/8" (1673.2) 10-3/8" (263.5)

CL

CL

CL

A

B

C

40-5/16" (1023.9) STANDARD

HINGE BACKSET: 5/16" (7.9)

FOR USE WITH TWO HINGES 1-3/8" (34.9) DOOR

3-1/2" (88.9) OR 4" (101.6)

STRIKE BACKSET 3/16" (4.8)

2-3/4" (69.9)STRIKE

L

L

L

HINGE SIZE MAY VARY, LOCATION REMAINS THE SAME.CL



47CURRIES Standard Hinge & Strike Locations for 1-3/8" Frame


September, 2013

LL

SIZE A B C

6'8" (2032) 9-3/4" (247.7) 29-15/16" (760.4) 10-3/8" (263.5) 6'10" (2082.8) 9-3/4" (247.7) 30-15/16" (785.8) 10-3/8" (263.5) 7'0" (2133.6) 9-3/4" (247.7) 31-15/16" (811.2) 10-3/8" (263.5) 7'2" (2184.4) 9-3/4" (247.7) 32-15/16" (836.6) 10-3/8" (263.5)

CL

CL

CL CL

A

B

C

40-5/16" (1023.9) STANDARD


FOR USE WITH THREE HINGES 1-3/8" (34.9) DOOR

3-1/2" (88.9) OR 4" (101.6)


2-3/4" (69.9)STRIKE

L

L

L

B


NOTE: FOR FRAMES UNDER 60" TALLWE WILL CENTER THE STRIKEFOR ALL MANUFACTURERS LOCATIONS UNLESS NOTED OTHERWISE ON THE ORDER.


48CURRIES Standard Hinge & Strike Locations for 1-3/4"Dutch FrameFrame Technical DataNovember, 2004

L

L

SIZE A B C D E

6'8" (2032) 7-1/4" (184.2) 24-1/4" (616) 13-1/2" (342.9) 22-3/4" (577.9) 12-1/4" (311.2) 6'10" (2082.8) 7-1/4" (184.2) 26-1/4" (666.6) 13-1/2" (342.9) 22-3/4" (577.9) 12-1/4" (311.2) 7'0" (2133.6) 7-1/4" (184.2) 28-1/4" (717.6) 13-1/2" (342.9) 22-3/4" (577.9) 12-1/4" (311.2) 7'2" (2184.4) 7-1/4" (184.2) 30-1/4" (768.4) 13-1/2" (342.9) 22-3/4" (577.9) 12-1/4" (311.2) 7'10" (2387.6) 7-1/4" (184.2) 35-1/4" (895.4) 16-1/2" (419.1) 22-3/4" (577.9) 12-1/4" (311.2) 8'0" (2438.4) 7-1/4" (184.2) 37-1/4" (946.2) 16-1/2" (419.1) 22-3/4" (577.9) 12-1/4" (311.2) 9'0" (2743.2) 7-1/4" (184.2) 49-1/4" (1251) 16-1/2" (419.1) 22-3/4" (577.9) 12-1/4" (311.2) 10”0" (3048) 7-1/4" (184.2) 61-1/4" (1555.8) 16-1/2" (419.1) 22-3/4" (577.9) 12-1/4" (311.2)

CL

CL

CL

CLCL

CL

A

B

E

35" (889) STANDARD


DUTCH DOOR

4-1/2" (114.3) OR 5" (127)


4-7/8" (123.8)STRIKE

L

L

L

L

D

C

50" (1270) STANDARD

SHELF HEIGHT IS42" (1066.8) STANDARD

NOTE:MAXIMUM FIRE LABELWIDTH: 3'8" (1117.6)

L

L

L


PLEASE INDICATE WHEN ADA COMPLIANCE IS REQUIRED. 48" CL IS NOT PRACTICAL WITHSOME DEADLOCKS.

* *


49Frame Standard Rabbet Dimensions


April, 2002

L

DOUBLE RABBET

SINGLE RABBET

MULLION

2" (50.8)

5/8" (15.8)

VARIES

1/2" (12.7)

DOOR THICKNESS DIMENSIONS

1-3/8" 1-15/16" (49.2) 1-3/4" 1-9/16" (39.7) 2"* 1-9/16" (39.7) 2-1/4"* 1-9/16" (39.7)


1-3/8" 1-9/16" (39.7) 1-3/4" 1-15/16" (49.2) 2"* 2-3/16" (55.5) 2-1/4"* 2-7/16"

2" (50.8)

5/8" (15.8)

VARIES

1/2" (12.7)


1-3/8" 1-9/16" (39.7) 1-3/4" 1-15/16" (49.2) 2"* 2-3/16" (55.5) 2-1/4"* 2-7/16"

2" (50.8)

5/8" (15.8)

VARIES


1-3/8" 1-15/16" (49.2) 1-3/4" 1-9/16" (39.7) 2"* 1-9/16" (39.7) 2-1/4"* 1-9/16" (39.7)


1-3/8" 1-9/16" (39.7) 1-3/4" 1-15/16" (49.2) 2"* 2-3/16" (55.5) 2-1/4"* 2-7/16"

* NOT AVAILABLE KNOCKDOWN (KD)


504-1/2" Ultima Hinge ReinforcementFrame Technical Data

July, 2010

L

TO REMOVE SHIM PLATE, INSERT FLAT SCREWDRIVER BETWEEN SHIM AND REINFORCEMENT, AND PRY SHIM AWAYFROM REINFORCEMENT.

NOTE: 1) IF SHIM IS REMOVED, PRIME PAINT HINGE REINFORCEMENT.2) NOT RECOMMENDED FOR CONVERSION TO ELECTRIC HINGE PREPARATION.

DEFAULT REINFORCEMENT FOR ALL 4-1/2" STANDARD

AND HEAVYWEIGHT HINGES

DRILLED AND TAPPED PER HINGE TEMPLATE

PROJECTIONS FOR RESISTANCE WELDING

5-9/16" (141.3)

9" (228.6)

1-7/32" (30.9)

18 GA. (1.2) STEEL SHIM PLATE

7 GA. (4.5) STEEL

MUDCAP STANDARD ON “M” SERIES FRAME

OFFSET IN 16 GA. (1.4) FRAMEWITH SHIM PLATE .134" (3.4)WITHOUT SHIM PLATE .180 (4.6)

.134" (3.4) .180" (4.6)


515" Hinge Reinforcement


November, 2004

Heavy 5" Hinge Reinforcement

L

DRILLED AND TAPPED PERHINGE TEMPLATESTD. 12-24

PROJECTIONS FORRESISTANCE WELDING

5-9/16" (141.3)

9" (228.6)

7 GA. (4.5) STEEL

PROJECTIONS FORRESISTANCE WELDING

INDICATES HEAVY WEIGHT HINGE REINFORCEMENT

DRILLED AND TAPPED PERHINGE TEMPLATESTD. 12-24

NOTE: ELECTRICAL HINGE PREPARATION AVAILABLEPER TEMPLATE

5-9/16" (141.3)

9" (228.6)

7 GA. (4.5) STEEL

1-5/8"(41.3)

1-5/8"(41.3)

L


52EH - Electric HingesFrame Technical Data

July, 2011

PER TEMPLATE

5/8" X 13/16"SLOTS TYPICAL

TYPICAL 4-1/2" ELECTRIC HINGE PREPARATION SHOWN FITS MANY ELECTRIC HINGES. OTHER ELECTRIC HINGEPREPARATIONS WILL BE PREPARED PER THE HINGE TEMPLATE.

NOTE: ELECTRIFIED HINGE REINFORCEMENT AVAILABLE AS LOOSE PART #FH0300


53HFG Hinge Strap Reinforcement


October, 2013

L

WELD AS SHOWN

7 GA. (4.5) X 1-1/4" (31.8) X 9" (229)HINGE REINFORCEMENT.DRILLED AND TAPPED FOR 12-24 UNC (STANDARD)(1/4-20 UNC OPTIONAL)

HOLE FOR ABUSE-RESISTANT STUD(OPTIONAL)

HIGH FREQUENCY HINGE REINFORCEMENT STRAPS

14 GA. (2.0) REINFORCEMENT

MUDCAP


54Full Width Hinge ReinforcementFrame Technical Data

November, 2004

L

7 GA. (4.5) X JAMB DEPTH MINUS 1/2" (12.7) X 10" (254) HINGEREINFORCEMENT.DRILLED AND TAPPED FOR 12-24 UNC (STANDARD)(1/4-20 UNC OPTIONAL)

HOLE FOR ABUSE-RESISTANT STUD(OPTIONAL)

COVERBOX

ARC WELD FULL WIDTH ALONG EACH END IN RABBETS (ONLY WHEN SPECIFIED).STANDARD WELDS INDICATED WITH AT END.


55Continuous Hinge Reinforcement


September, 2005

L

3/4" (19.1)

12 GA. (2.6)REINFORCING

1/4" (6.4)

1/4" (6.4)

3/4" (19.1)

12 GA. (2.6)REINFORCING

SURFACE MOUNTED TYPE CONCEALED MOUNTED TYPE

HGCF CODE

NOTE: HINGE MANUFACTURERS RECOMMEND REINFORCEMENTS ON 20, 18, 16 GAUGE FRAMES.

HGCR CODE


56Security Hinge and Grout GuardFrame Technical Data

November, 2004

LARC WELD FULL WIDTH ALONG EACH END

PROJECTIONS FOR RESISTANCE WELDING

7 GA. (4.5) X 1-19/32" (40.4) X 9" (228.6)HINGE REINFORCEMENT.DRILLED AND TAPPED FOR 12-24 UNC (STANDARD)(1/4-20 UNC OPTIONAL)OFFSET PER HINGE THICKNESS

HOLE FOR ABUSE-RESISTANT STUDPER TEMPLATE AS REQUIRED.

16 GA. (1.4) COVERBOX SPOT WELDED OVER HINGE REINFORCING.


57Electric Hinge and Grout Guard


November, 2004

LARC WELD FULL WIDTH ALONG EACH END(OPTIONAL)

WELD PROJECTIONS FOR RESISTANCE WELDING

7 GA. (4.5) X 1-19/32" (40.4) X 9" (228.6)HINGE REINFORCEMENT.DRILLED AND TAPPED FOR 12-24 UNC (STANDARD)(1/4-20 UNC OPTIONAL)OFFSET PER HINGE THICKNESS

ELECTRICAL CONDUIT KNOCKOUT

16 GA. (1.4) GROUT GUARD COVER-BOX SPOT WELDED OVER HINGE RE-INFORCING.

#8 PAN HEAD SCREWELECTRICAL HINGE WIRE ACCESSHOLE PER TEMPLATE.

NOTE: JUNCTION BOXES ARE NOT CAULKED AT THE FACTORY. TO BEFIELD CAULKED BY INSTALLATION CONTRACTOR.


58HGA - Anchor Hinge PreparationFrame Technical Data

April, 2002

L

7 GA. (4.5) HINGE REINF.

CURRIES DOES NOT DRILL AND TAPFOR HINGE SCREWS, UNLESS FRAME ISFACTORY WELDED AND PHYSICALSAMPLES ARE PROVIDED.

IF FRAME IS STICK OR KD THE PARTS ARESHIPPED LOOSE AND ARE NOT WELDED TOGETHER,DRILL AND TAP IN FIELD.

ARC WELD

DOOR RABBET IS 1-15/16" (49.2)


59HGD - Hinge - Double Acting


April, 2002

L12 GA. (2.6)REINFORCING

.25 (6.4)

VERTICAL JAMB LINE

2.25 (57.2)

3.375(85.7)

NOMINALDOOR HEIGHT


60Pocket Pivot PreparationFrame Technical Data

April, 2002

L

5/8" (15.9) STOP HEIGHTIF USING COVERBOX

7 GA. (4.5) REINF. TAB

PREPARATION:SIZE, DRILL AND TAP PER TEMPLATE

16 GA. (1.4) COVERBOX

PER TEMPLATE

PER TEMPLATE

NOTE: SOME POCKET PIVOTS REQUIRE FRAME FACE DIMENSIONS GREATER THAN 2" (50.8) - KD FRAMES NOT AVAILABLE OVER 2" FACE.


61SDL - Strike - Double Lip


November, 2004

L

PER TEMPLATE

PER TEMPLATE

12 GA. (2.6)REINFORCING TABS

NOTE: CONTACT FACTORY ON AVAILABILITYWHEN USED WITH “C” TYPE COMPRESSIONANCHOR KD FRAMES.


62Rescue Hardware FrameFrame Technical Data

November, 2004

L

12 GA. (2.6) REINFORCEMENT

PER TEMPLATE

PER TEMPLATE


DOUBLE LIP LATCH STRIKE12 GA. (2.6) REINFORCEMENT

COVERBOX

2" (50.8) MINIMUM FACE REQUIRED FOR COVERBOX

7-3/4"(196.9)

PERTEMPLATE

FLOORLINE

CL

CL

EMERGENCY STOP STRIKE SIDE

NOTE: CONTACT FACTORY ON AVAILABILITY WHEN USED WITH “C” TYPECOMPRESSION ANCHOR KD FRAMES.


63Frame Pivots - Top, Bottom - Center Hung


December, 2006

TOP PIVOT7 GA. (4.5) REINF.

COVERBOX

MUDCAP

MUDCAP

CENTER HUNGCASED OPENING

TOP AND BOTTOM DOUBLE ACTING PIVOT


BOTTOM PIVOT7 GA. (4.5) REINF.

TOP PIVOT7 GA. (4.5) REINF.1/8" INSET OR EDGE HUNG

COVERBOX

EDGE HUNGCASED OPENING

TOP AND BOTTOM SINGLE ACTING PIVOT



EDGE HUNGNOTE: NOT ALL BOTTOM PIVOTS REQUIRE A FRAME PREP.


64Frame Pivots - Top, Intermediate, Bottom - Single ActingFrame Technical Data

April, 2002

L


INTERMEDIATE PIVOT7 GA. (4.5) REINF.

TOP PIVOT7 GA. (4.5) REINF.

COVERBOX

MUDCAP


65E1 Strike Reinf. (ANSI A115) 1-1/4" x 4-7/8"


April, 2002

L

E2 Strike Reinf. (ANSI A115) 1-1/8" x 2-3/4"

L

16 GA. (1.4) REINF.COVER BOX1-1/16" (27) DEEP

1-1/4" (31.8)

4-7/8"(123.8)

40" (1016) TO STANDARD ON 1-3/4" (44.5) DOOR

CL

STANDARD STRIKEBACKSET 5/16" (7.9)

SCREW HOLES ARE EXTRUDED TO PROVIDETHREAD DEPTH EQUAL TO 12 GA. (2.6) PLATE

16 GA. (1.4) REINF.COVER BOX1" (25.4) DEEP

1-1/8" (28.6)

2-3/4"(69.9)


40-5/16" TO STANDARD ON 1-3/8" DOOR

CL

STANDARD STRIKEBACKSET 3/8" (9.5)

1-3/4" DOORBACKSET 3/16"

1-3/8" DOOR


SIZE AND TAP PER ANSI 115.2

SIZE AND TAP PER ANSI 115.1 AND 115.2

CL


66E1B - Strike Reinf. 1-1/4" x 4-7/8" No LipFrame Technical Data

April, 2002

L

4-7/8"(123.8)

1-1/4"(31.8)

40" (1016) TOSTANDARD ON 1-3/4" (44.5) DOOR

CL

12 GA. (2.6)REINF. TABS

PER TEMPLATE


67E3 Deadlock Strike Reinf. (ANSI/A115) 1-1/8" x 3-1/2"


April, 2002

L

E4 Deadlock Strike Reinf. (ANSI/A115) 1-1/8" x 2-3/4" No Lip

L

16 GA. (1.4) REINF. COVER BOX1-1/16" (27) DEEP

1-1/8" (28.6)

3-1/2"(88.9)


CL




16 GA. (1.4) REINF. COVER BOX1" (25.4) DEEP

1-1/8" (28.6)

2-3/4"(69.9)


CL





68EJ2 - Jamb Lock 2" (50.8) FaceFrame Technical Data

April, 2002

L

PERTEMPLATE

PERTEMPLATE

PERTEMPLATE

REINF. TABSPER TEMPLATE

PERTEMPLATE

2" (50.8) MIN. FACE3-1/16" (77.8) MIN. FACEON DRYWALL FRAME

40" (1016)

CL


69EJ4, EJ8, EJ12 - Jamb Lock


April, 2002

L

PERTEMPLATE

COVERPLATE

PERTEMPLATE

CUTOUTSPER

TEMPLATE

4" (101.6) STANDARD8" (203.2) STANDARD12" (304.8) STANDARD

STRIKE40" (1016)

CL


70E30 - Strike - Pocket LockFrame Technical Data

July, 2003

L

PER TEMPLATE

PER TEMPLATE

7 GA. (4.5)REINF. TABS

40" (1016)

CL


71MAG - Magnetic Lock


July, 2003

L

PER TEMPLATE

PER TEMPLATE

REINF. TABSPER TEMPLATE


72E5 Rim Vertical Rod Surface Strike Reinf.Frame Technical Data

April, 2002

L

G20 Vertical Rod Exit Mortise Strike Preparation

L

1-3/4" (44.5)

12 GA. (2.6)

10" (254)

CL

12 GA. (2.6) REINF. WELDEDTO INSIDE OF SOFFIT TIGHTTO DOOR RABBET STOP

G20 PREPARED FOR MORTISE STRIKES PERTEMPLATE OF HARDWARE MANUFACTURER

SPECIFY EXIT DEVICE AND STRIKE BEING USED WHEN ORDERING

E5 REINFORCING IS LOCATED ON CENTERLINE OF HEAD FOR PAIR FRAMESAND ADJACENT TO STRIKE JAMB ON SINGLE SWING FRAMES.

DOOR R

ABBET

HEADS

DOOR


73E8 Rim Exit Reinforcement


April, 2002

L

12 GA. (2.6) REINF.WELDED TO INSIDEOF SOFFIT TIGHT TODOOR RABBET STOP

41" (1041.4) TO STANDARD

CL

8" (203.2)

1-1/4" (31.8)*

12 GA. (2.6)

DOOR

* THE REINFORCEMENT WIDTH WILL BE EQUAL TO THE SOFFIT WIDTH WHEN LESS THAN 1-1/4" (31.8).CUSTOMER SHOULD VERIFY HARDWARE COMPATIBILITY BEFORE ORDERING NARROW SOFFITS.


74E9 Electric StrikesFrame Technical Data

April, 2002

L

NOTE: FIRE RATED FRAMES INCORPORATING AN ELECTRIC STRIKE WITH A COVERBOX, REQUIRE THAT THE WALL BOARD PENETRATE THE THROAT OF THE FRAME BY 1/2" (12.7) MINIMUM. ELECTRIC STRIKE MUST BE LISTED FOR USE WITH FIRE RATED OPENINGS.

16 GA. (1.4) REMOVABLE COVER BOX

CONFIGURATION OF CUTOUT VARIESPER HARDWARE MFG. TEMPLATE

SPECIFY STRIKE BEING USED WHEN ORDERING

STRIKECL

VERTICAL LOCATION OF ELECTRIC STRIKE WILLVARY WITH THE HARDWARE MANUFACTURER,WHEN ORDERING FRAMES PREPARED FOR ANELECTRIC STRIKE, SPECIFY THE TYPE OF LOCK

BEING USED ALONG WITH CENTERLINE

DIMENSION REQUIRED OF THE LOCK.

7/8" (22.2) DIA.KNOCKOUT FOR ELECTRIC CONNECTOR



75Conduit - Coverbox Clearance Dimensions


September, 2005

L1-1/8" (28.6) OR 7/8" (22.2) DIA.

KNOCKOUT

RABBET CL

FACE

END VIEW OF FRAME AND COVERBOX

REMOVABLE COVER

AS REQUIRED

CL

CL

DEPTH

WIDTH

COVERBOX

1/2" (12.7) CONDUIT CONNECTOR LOCKNUTBY OTHERS

1/2" (12.7) CONDUIT CONNECTORBY OTHERS

SIDE VIEW OF COVERBOX

LOCKNUT

1-1/8" (28.6)*

MINIMUM INSIDE DEPTH DIMENSION REQUIREDTO ACCOMODATE THE LOCKNUT.

* 1-1/2" (38.1) FOR 3/4" CONDUIT CONNECTOR

1/2" CONDUIT CONNECTORS ARE FOR 7/8” KNOCKOUT / 1-1/8” HIGH COVERBOX3/4" CONDUIT CONNECTORS ARE FOR 1-1/8" KNOCKOUT / 1-1/2" HIGH COVERBOX

DOUBLE KNOCKOUT FOR 1/2" AND 3/4"

CONDUIT CONNECTORS ARE FOR THE 1-1/2" HIGH COVER BOX ONLY

1-1/8" HIGH COVERBOX HAS 7/8" KNOCKOUT ONLY FOR1/2" CONDUIT CONNECTOR

1/2"(12.7)

3/4"(19.1)


76Conduit Preparation (RW-3)Frame Technical Data

March, 2013

L

6.00" + 1.00"

TOP

JAMB MULLION

HEAD MULLION

LOCK SIDE

6.00" + 1.00"

1/2" EMT CONDUITFACTORY INSTALLED WHEN REQUESTED(MULLION ONLY)

REQUIRED FOR POWER TRANSFER AND ELECTRIC STRIKES


77E10 Standard Mtg. 14 ga. Closer Reinforcement


January, 2005

L

E11 Parallel Arm Mtg. 14 ga. Closer Reinf.

L

14 GA. (1.9)

1-3/4" (44.5)10" (254)

7" (177.8)

14 GA. (1.9)

1-1/4" (31.8)

20" (508)


DOOR

HINGE SIDE

HINGE SIDEDOOR

NOTE: WHEN SOFFIT WIDTH IS LESS THAN 1" - E16 WILL BE USED


78E12 Top Jamb Mtg. 14 ga. Closer Reinf.Frame Technical Data

November, 2004

L

14 GA. (1.9)

2" (50.8)

16" (406.4)

1-3/4" (44.5)2-3/4" (69.9)

DOOR

HINGE SIDE


79E13 Corner Bkt. Mtg. 14 ga. Closer Reinf.


January, 2005

L

Double Egress Frame Closer Reinforcements

L

14 GA. (1.9)

1-1/4" (31.8)

8" (203.2)

8" (203.2)


E11 ------------------PARALLEL ARM MOUNTING ------------------------14 GA. (1.9)20" (508) LONG

E10 ------------------REGULAR MOUNTING ------------------------------14 GA. (1.9)10" (254) LONG

E12 ------------------TOP JAMB MOUNTING ------------------------------14 GA. (1.9)16" (406.4) LONG

E17A ----------------FULL SLEEVE----------------------------------------14 GA. (1.9)REGULAR, TOP JAMB 16" (406.4) LONGPARALLEL ARM MOUNTINGS

E18 ------------------HALF SLEEVE --------------------------------------14 GA. (1.9)REGULAR AND 16" (406.4) LONGPARALLEL ARM MOUNTINGS

REGULARTOPJAMB

DOOR

HINGE SIDE


80E15 Closer Reinf.Frame Technical Data

October, 2014

L

E16 Double Parallel Arm 14 ga. Closer Reinf.

L

14 GA. (1.9)

1-3/4" (44.45)24” (609.6)

14 GA. (1.9)

VARIES PER SOFFIT WIDTHUP TO 1-5/8" (41.3)

1-1/4" (31.8)

14 GA. (1.9) ADDITIONAL REINF. ADDEDWHEN SOFFIT IS UNDER 2" (50.8) IN WIDTH

20" (508)

20" (508)

14 GA. (1.9) ADDITIONAL REINF. WELDED TO INSIDEOF SOFFIT TIGHT TO DOOR RABBET STOP

DOOR

DOOR

HINGE SIDE

HINGE SIDE

1/2” (12.7)


81E17 14 ga. Full Sleeve Closer Reinforcement

Frame Technical DataApril, 2015

L

E18 14 ga. Formed Half Sleeve Closer Reinf.

L

14 GA. (1.9)

1-3/4” (44.5)

16” (406.4)

1” (25.4) MIN.

1-3/4” (44.5)

14 GA. (1.9)

2-3/8” (60.3)

1” (25.4) MIN.

1-3/4” (44.5)

HINGEJAMBLINE

16” (406.4)

NOTE: SPECIAL PROFILE REINFORCEMENT REQUIRED WHEN CLOSER IS MOUNTED TO FRAME FACE GREATER THAN 2"

16” (406.4)14 GA. (1.9)

1-3/4” (44.5)

1-3/8” (34.9) NOTE 1 3/4” (19.1) NOTE 2

5/8” (15.9)

1-15/16” (49.2) FOR 1-3/4” (44.5) DOOROR

1-9/16” (39.7) FOR 1-3/8” (34.9) DOOR

NOTE:1) 1-1/2” (38.1) MINIMUM SOFFIT REQ’D2) 1” (25.4) MINIMUM SOFFIT REQ’D

NOTE: SPECIAL PROFILE REINFORCEMENT REQUIRED WHEN CLOSER IS MOUNTED TO FRAME FACE GREATER THAN 2”

DOORHINGE SIDE


82EPT - Electronic Power Transfer


May, 2011

L

TOP HINGE

PER TEMPLATE

*

12 GA. (2.6)REINFORCINGTABS

PERTEMPLATE

PER TEMPLATE

* LOCATION PER TEMPLATE. IF NO LOCATION ON TEMPLATE, THEN LOCATION MUST BE SPECIFIED WITH ORDER. THE QUANTITY OF HINGES MAY REQUIRE COORDINATION OF LOCATION WITH DOOR, (EX. 4 HINGES ON A 7'0"). WOOD DOORS MAY REQUIRE OTHER LOCATIONS


83G21 - G22 Removable Hardware Mullion


April, 2002

L

H3A - H3B Surface Bolt Preparation

L

MULLION TOP BRACKET MOUNTING SCREWS TO BE DRILLED ANDTAPPED IN FIELD BY HARDWARE INSTALLER.

G21 PLATE REINFORCEMENTUSED WHEN SOFFIT IS 3" (76.2) WIDE ORGREATER.

G21

G22 PLATE REINFORCEMENTUSED WHEN SOFFIT IS LESS THAN3" (76.2).

G22

5/8" (15.9) C.R.S. FILLER BLOCK ISFURNISHED WHEN SOFFIT WIDTH IS TOONARROW TO APPLY HARDWARE TO SOFFIT

PLUG WELDED ONLY

WELDEDDOORDOOR HARDWARE MULLIONASSEMBLY

H3B-12 GA. (2.6)

H3A-12 GA. (2.6)

1-3/4" (44.5)

1-3/4" (44.5)

10" (254)

10" (254)

H3A FACE PREP.12 GA. (2.6) REINF. WELDEDTO INSIDE OF FRAME FACE

CLHEAD AND REINFORCEMENT

H3B SOFFIT PREP.12 GA. (2.6) REINF. WELDEDTO INSIDE OF SOFFIT TIGHT

TO DOOR RABBET STOP

NOTE: WHEN ORDERING SPECIFYEITHER H3A OR H3B REINFORCING

12 GA. (2.6)

DOOR

OF DOORS

DOOR SIDE


84G24 Coordinator ReinforcementFrame Technical Data

CL - Closer Reinforcement Per Template

October, 2014

L

12 GA. (2.6)

1-3/8" (34.9) 10" (254)

CL

12 GA. (2.6) REINF. WELDEDTO INSIDE OF FRAME FACE.

DOOR

OF DOORSCL

OF PAIR

2" (51)

14 GA. (1.9)

*PER TEMPLATE

*PER TEMPLATE

DOOR

* SPECIFY MANUFACTURER AND MODEL NUMBER WHEN ORDERINGADVISE POWER SOURCE LOCATION IF REQUIRED

HINGE SIDE


85Grout Hole


September, 2008

L

RABBET PREPARATION(DOOR RABBET STANDARD)

FACE PREPARATION(DOOR FACE STANDARD)

12 GA. (2.6) REINF. PLATE1-3/8" (35) DIA.HOLE IN REINF. PLATE

12 GA. (2.6) REINF. PLATE1-3/8" (35) DIA.HOLE IN REINF. PLATE

FILLER PLATESAME GAUGE AS FRAME.SHIPPED LOOSE.1-3/8" X 1-3/8"(35 X 35)

FILLER PLATESAME GAUGE AS FRAME.SHIPPED LOOSE.1-3/8" X 1-3/8"(35 X 35)


86H1 Flush Bolt ReinforcementFrame Technical Data

April, 2002

L

H2 Flush Bolt Prep. and Reinf. (ANSI)

L

1-1/4" (31.8)12 GA. (2.6)

8" (203.2)

OF OPENING AND REINFORCEMENTCL

12 GA. (2.6) REINF. WELDED IN CENTER OF DOOR RABBETCL

12 GA. (2.6) 16 GA. (1.4) REINF. COVER BOX1-1/16" (27) DEEP

2-1/4" (57.2)

CL

CL

OF DOORS

CUTOUT

INACTIVE DOOR

13/16" (20.6)

15/16" (23.8)

15/32" (11.9) BACKSET


DOOR

DOOR


87H4 Auto Flush BoltFrame Technical Data

April, 2002

L

H5 Non-handed Flush Bolt

L

PREPARATION FOR AUTOMATIC FLUSH BOLT IS PER HARDWARE MANUFACTURER’S TEMPLATE.

PLEASE SPECIFY MANUFACTURER AND MODEL NUMBER WHEN ORDERING.

LABELED IF HARDWARE IS APPROVED AND PREPPED TO TEMPLATE.

3-7/8" (98.4)

12 GA. (2.6) REINF.

15/16" (23.8)

OF DOORSCL

NOTE: STRIKE PLATE INSTALLED FILLER PLATE MAY BE PURCHASED SEPARATELY IN PACKAGES OF 50 PIECES WITH SCREWS.

3-1/4" (82.6) 16 GA. (1.4) GALV. FILLER PLATEPART #CF004637

16 GA. (1.4) GALV. FILLER PLATEPART #CF001257

C' SUNK FOR #8-32 X 5/8" (15.9)FLAT HEAD HARDWARE SCREW

HEADCL

CL

7/8" (22.2)

CL

5/8" (15.9)1-1/8" (28.6)


88Electric Magnetic Door Position SwitchFrame Technical Data

April, 2002

L

16 GA. (1.4) GROUT GUARD COVERBOX ENDS SPOT WELDEDOVER PREPARATION.

ELECTRICAL CONDUITKNOCKOUT AS REQUIRED.

#8 PAN HEAD SCREW.

CUTOUT SIZE AND LOCATION PERHARDWARE TEMPLATE

12 GA. (2.6)REINFORCING TAB.

NOTE: JUNCTION BOXES ARE NOT CAULKED AT THE FACTORY. TO BE FIELD CAULKED BY INSTALLATIONCONTRACTOR.


89Electric Fully-Concealed Door Position Switch


April, 2002

L

16 GA. (1.4) GROUT GUARD COVERBOX SPOT WELDED OVERPREPARATION

ELECTRICAL CONDUITKNOCKOUT AS REQUIRED

#8 PAN HEAD SCREW.

CUTOUT SIZE AND LOCATION PERHARDWARE TEMPLATE

12 GA. (2.6)REINFORCING TAB

NOTE: JUNCTION BOXES ARE NOT CAULKED AT THE FACTORY. TO BE FIELD CAULKED BY INSTALLATIONCONTRACTOR.


90Cabinet Jamb FrameFrame Technical Data

April, 2002

L

DOOR OPENING

ROUGH OPENING

DOOR OPENING

ROUGH OPENING

NOT U.L. LISTEDS.M.W. JAMB SECTIONBUCKS SHIP LOOSE SQUARE BUTT ENDFIELD ASSEMBLED WITH SCREWSOR WELDED

1-3/4" (44.5)1" (25.4)

1-7/8" (47.6)

ROUGH OPENING DETERMINESTHE LENGTH OF THE BUCK LEGS

MACH SCREW#8 X 1/2" PAN HEAD

7/8" (22.2)


91Rough Buck Frame


February, 2011

L

2-1/2" (63.5) MIN.3" (76.2) MAX.

2-1/2" (63.5) MIN. TYP.3" (76.2) MAX. TYP.

DOOROPENING

ROUGHOPENING

DOOR OPENING

ROUGH OPENING

U.L. LISTED ROUGH BUCK FRAMESBUCKS SHIPPED LOOSE SQUARE BUTT END.FULLY PREPARED FOR INSTALLATIONWITH MOUNTING HOLES.

FINISH BUCK16 GA. (1.4) OR 14 GA. (1.9)

HINGE OR STRIKE REINF.1/4-20 NC X 1-1/4"FLAT HEAD MACH SCREW

2" (50.8)

2" (50.8)

#8 x 1/2"PAN HEADMACH SCREW

12 GA. (2.6) REINF. SUB-CHANNELU.L. FRAME ONLY

SUB-BUCK14 GA. (1.9) ONLY FOR LABEL

2" (50.8)

2" (50.8)

CORNER DETAILCORNER IS NOTCHED FOR FIELD INSTALLATIONFINISH BUCK CAN NOT BE WELDED PRIOR TOINSTALLATION.

NOTE: LABEL FRAMES FURNISHED WITH ATTACHING SCREWS AND BOLTS FOR ASSEMBLY


92Curriseal Frame Flush KD - WM - WGFrame Technical Data

September, 2003

L

K.D. “M” TYPE FLUSH GAUGE - 18 GA. (1.2), 16 GA. (2.4), 14 GA. (1.9) JAMB DEPTHS:DOUBLE RABBET (WM) 5-1/4" (133.4) - 14" (355.6) (1/8" (3.2) INCREMENTS)SINGLE RABBET (WG) 4-1/8" (104.8) - 14" (355.6) (1/8" (3.2) INCREMENTS) AVAILABLE WITH 4" (101.6) FACE HEADS DOUBLE RABBET AVAILABLE IN COMMUNICATING FRAMES WITH A 6-1/2" (165.1) MIN. JAMB DEPTH

HARDWARE RESTRICTIONS

NOT RECOMMENDED- CLOSERS WITH REMOVABLE STOPS- VERTICAL ROD DEVICES WITH STRIKES MORTISED IN THE STOP- STOP ACTIVATED VERTICAL ROD DEVICES

NOTE: SOFFIT MOUNTED SURFACE HARDWARE MAY REQUIRE+_ 1/8" (3.2) ADJUSTMENT OF MOUNTING HOLES TO ACCOMODATEWEATHERSTRIP AND ENSURE NORMAL DOOR OPERATION.

CURRISEAL

ACTUAL SIZECOLOR: DARK BROWN

2-1/8"(54.0)

1-9/16" (39.7)

1-15/16" (49.2)ORVARIES

5/8" (15.9)ONLY

1" (25.4)1-1/4" (31.8)1-1/2" (38.1)1-3/4" (44.5)

2" (50.8)

1/2" (12.7)*

2-5/8" (66.7)ONLYWG

WM/WG

1-3/4" DOOR(44.5)

1/4" (6.3)

1/8" (3.2)

5-3/4" (146.1) JAMB DEPTH AVAILABLE WITH 7/16" (11.1) RETURNSTO PROVIDE A 4-7/8" (123.8) THROAT OPENING

CURRISEAL FRAME IS DESIGNED FOR USE WITH THE CURRISEAL ONLY

*KD CORNER


93Curriseal Frame KD Drywall - WC - WCG


September, 2003

L

K.D. “C” TYPE DRYWALL GAUGE - 18 GA. (1.2), 16 GA. (2.4), 14 GA. (1.9) JAMB DEPTHS:DOUBLE RABBET (WC) 5-1/4" (133.4) - 14" (355.6) (1/8" (3.2) INCREMENTS)SINGLE RABBET (WCG) 4-1/8" (104.8) - 14" (355.6) (1/8" (3.2) INCREMENTS) DOUBLE RABBET AVAILABLE IN COMMUNICATING FRAMES WITH A 6-1/2" (165.1) MIN. JAMB DEPTH

HARDWARE RESTRICTIONS

NOT RECOMMENDED- CLOSERS WITH REMOVABLE STOPS- VERTICAL ROD DEVICES WITH STRIKES MORTISED IN THE STOP- STOP ACTIVATED VERTICAL ROD DEVICES

NOTE: SOFFIT MOUNTED SURFACE HARDWARE MAY REQUIRE+_ 1/8" (3.2) ADJUSTMENT OF MOUNTING HOLES TO ACCOMODATEWEATHERSTRIP AND ENSURE NORMAL DOOR OPERATION.

CURRISEAL

ACTUAL SIZECOLOR: DARK BROWN

2-1/8"(54.0)

1-9/16" (39.7)

1-15/16" (49.2)ORVARIES

5/8" (15.9)ONLY

1-1/2" (38.1)1-3/4" (44.5)

2" (50.8)

1/2" (12.7)

2-5/8" (66.7)ONLYWC/WCG

1-3/4" DOOR(44.5)

1/4" (6.3)

1/8" (3.2)

CURRISEAL FRAME IS DESIGNED FOR USE WITH THE CURRISEAL ONLY

KD CORNER

3/8" (9.5)


94NotesFrame Technical Data

January, 2007


95Notes


January, 2007


96Communicating FrameFrame Technical Data

April, 2002

L

NOTE:

U.L. AND W.H.I. LABELED FRAMES MAY BE PROVIDEDWITH COMPRESSION TYPE ANCHORING SYSTEM.

“M” PROFILE FLUSH K.D. “C” & “CM” PROFILE DRYWALL

EQUAL RABBET1-15/16" (49.2) FOR 1-3/4" (44.5) DOORS4-7/8" (117.5) THRU 14" (355.6) JAMB DEPTH

UNEQUAL RABBET1-15/16" (49.2) X 1-9/16" (39.7) FOR1-3/4" (44.5) X 1-3/8" (34.9) DOORS4-1/2" (114.3) THRU 14" (355.6) JAMB DEPTH



UNEQUAL RABBET1-15/16" (49.2) X 1-9/16" (39.7) FOR1-3/4" (44.5) X 1-3/8" (34.9) DOORS4-1/2" (114.3) THRU 14" (355.6) JAMB DEPTH



97Pocket Door Frame - Standard 1-3/8" or 1-3/4" Door Single


March, 2011

L2"

(50.8)2" (50.8)FINISH OPENING

**

1

32

NOMINALDOOR

OPENING HEIGHT

*

2" (50.8)

NOMINALDOOR

OPENING HEIGHT

*

5/8" (15.9)

5/8" (15.9)

DOOR

1

VERIFY HARDWARE ADAPTABILITY

FRAME MUST BE INSTALLED AND HARDWARE TRACK MUST BE HUNG PRIOR TO FINISH

WALL STUDS BEING SET.AVAILABLE IN 18 GA. (1.2) AND 16 GA. (1.4) STEEL.

2" (50.8)

2" (50.8)FINISH OPENING WIDTH

**1/2" (12.7)

1/2" (12.7)

2

5/8" (15.9)

2" POCKET(50.8)

1-3/4" (44.5) DOOR 3

NOTE: 1-3/8" (34.9) DOORFRAME HAS 1-5/8" (41.3) POCKET

EQUAL

EQUAL

1" (25.4)DOOR POCKET

1/2" (12.7)

1/2" (12.7)

4" (101.6) MIN.12" (304.8) MAX.

ANCHOR P110

USED FOR METAL STUDOR WOOD STUD WALL

1" (25.4)

4-1/4" (107.9)

VARIES WITH JAMB DEPTH & STUD SIZE.SPECIFY STUD SIZE WHEN ORDERING.

FRAME FINISHED OPENING WIDTH SHOULD BE ORDERED 1" LESS THANDESIRED NET DOOR SIZE.EXAMPLE: A 3'0" (914.4) POCKET FRAME WILLHAVE FINISH OPENING WIDTH OF 2'11" (889).THIS ALLOWS THE USE OF STANDARD DOOR WIDTHS.

FINISH OPENING HEIGHT IS NOMINAL DOOR HEIGHTUSING CURRIES STANDARD DOOR UNDERCUT.

**

*

TRACK HARDWARE & REINFORCEMENT PROVIDED BY OTHERS


98Pocket Door Frame-Saw Mitered-Welded for 1-3/4" or 1-3/8" DoorsFrame Technical Data

March, 2011

1. MITER HEAD AND JAMB AT 45˚2. CLAMP AND TACK WELD AT BACKBEND AND FACE.3. CONTINUOUS WELD INSIDE SEAM.4. GRIND AND FINISH OUTSIDE SURFACES.

SPLIT HEAD AND HINGE JAMB

A

B

C

A

B

C

A

B

C

STRIKE JAMB

FLOOR ANCHORP165

2 PC 2 PML

FLOOR ANCHOR WILL BE WELDED TO FACES OF FRAME WHEN FACTORY WELDED.MUST BE ATTACHED TO FRAME FACES WHEN FRAME IS WELDED BY OTHERS.


99Stainless Steel Slip-On Type Spats


September, 2013

L

STAINLESS STEEL SLIP-ON SPATSTANDARD PROFILE IS MANUFACTUREDTO FIT OVER JAMB PROFILE.SPECIFY JAMB PROFILE WHEN ORDERING

18 GA. (1.1) #304 STAINLESS STEEL#4 SATIN GRAIN FINISH

NOTE:

SPATS ARE LABELED UP TOA HEIGHT OF 8" (203.2)

4" (101.6)STANDARD

4" (101.6)STANDARD

HOSPITAL TYPE SPATSTANDARD PROFILE IS MANUFACTURED

TO FIT OVER JAMB BELOW STOP.SPECIFY JAMB PROFILE WHEN ORDERING

18 GA. (1.1) #304 STAINLESS STEEL#4 SATIN GRAIN FINISH

NOTE:

HOSPITAL TYPE SPATSARE LABELED UP TO

A HEIGHT OF 6" (152.4)


100Hospital StopFrame Technical Data

April, 2002

ANCHOR PART NUMBER: P0079FILLER & BACKING PLATEUSED ON FRAMES NOT REQUIRING A FOOT CLIP ORFRAMES THAT HAVE SOME OTHER BASE ANCHORING METHOD.

ANCHOR PART NUMBER: P0077FILLER & COMBINATION BACKING PLATE-FOOT CLIPUSED ON FRAMES REQUIRING A FOOT CLIP.

NOTE: FOOTCLIP REQUIREDFOR LABEL

VARIES

STOP CUT AWAY ON 45˚ ANGLE TO RECEIVE FILLER

4" (101.6)STANDARD

FILLER SIZES AVAILABLEUP TO 9" (228.6) HIGH

CHOOSE EITHER P0077 OR P0079 BACKINGPLATE.WELD BACKING PLATE BEHIND CUTOUT.WELD FILLER INTO CUTOUT, GRIND, FILL ANDFINISH SMOOTH.

4" (101.6) STANDARDFROM FACTORY

*

HEIGHTS AVAILABLE UP TO 9" (228.6) HIGH6" (152.4) HIGH MAXIMUM ON FIRE RATED FRAMESFACTORY INSTALLED OR BY SECOND LOCATION SHOP

*

45˚ CUT

L


101Thermal Break Frame KD Flush Profile

Frame Technical DataDecember, 2016

L14 GA. (1.9) AND 16 GA. (1.4) GALVANEALED STEEL5/8” (15.9) HIGH STOP ONLYKD ONLY (FACE WELDED ONLY)MAXIMUM KD LENGTH - 118” JAMB, 116” HEADPUNCH FOR SILENCERS NOT AVAILABLE

ANCHOR OPTIONS:MASONRY TWIRE ANCHORSPLIT BASE ANCHORSPLIT WOODSTUD ANCHORPIPE SPACER ANCHOR

2” (50.8) OR 4” (101.6) FACE HEAD

DOOR RABBET

THERMAL BREAK

5-3/4” (146.1)THRU 12-3/4” (323.9)

JAMB DEPTH

THERMAL BREAK

DOORRABBET

2” (50.8)FACE


102Thermal Break Frame CCW Stick ComponentsFrame Technical Data

December, 2016

L16 GA. (1.4) AND 14 GA. (1.9) GALVANEALED STEEL ONLY5/8” (15.9) HIGH STOPS ONLY BUTT END JOINTS ONLYNOT LABELED

MULLION - 16 GA. (1.4) AND 14 GA. (1.9) 2” (50.8) FACE ONLY. PUNCH FOR SILENCERS NOT AVAILABLE.

5-3/4” (146.1)THRU 12-3/4” (323.9)

JAMB DEPTH

2” (50.8) FACE

THERMAL BREAK

THERMAL BREAK2” (50.8)

ONLY

DOOR RABBET

DOOR RABBET


103CCW - Drip Cap CCW 112 - 10'6-5/8" Lengths


March, 2009

L

Mullion Construction

L

10'6-5/8" (3216.3)

1" (25.4)

3/4" (19)

45˚DRIP CAP

C.C.W. 112

16 GA. (1.4) GALVANEAL

ORDER CODE: OM


104Removable Vertical Mullion/BracketFrame Technical Data

August, 2003

L

MULLION BRACKET IS USED AT THE TOP AND BOTTOM OF FRAME

ATTACH MULLION BRACKET TO FRAME

NOTCH MULLION FACE TO ALLOW DIMENSION “D” TO PASS THRU.

SLIDE MULLION IN PLACE

DIM. “B” = JAMB DEPTH - FRAME GAUGE THICKNESSDIM. “D” = DETERMINED BY FACE DIMENSION

*

*

EQUAL TO FACE DIM. MINUS 1/4" (6.4)

2"(50.8)

1" (25.4)

“D”

ARC WELD2 PLACES MINIMUM

DIM “B”

DRILL 3/16" (4.8)2 HOLES12-24 TAP

SCREWS INSTALLED

*


NOTE: THE MULLION WILL BE REMOVABLE FROM THE FACE OPPOSITE THE DOOR RABBET.


105Removable Horizontal Mullion/Bracket


July, 2014

L

NOTE: USED WITH REMOVABLE TRANSOM PANEL.


106Splice Connection Head or JambFrame Technical Data

April, 2002

L

Field Splice Connection with Bracket

L

1. FIT SPLICING SLEEVE REINF. HALFWAY INTO ONE SIDE AND TACK WELD IN PLACE.2. SLIP OTHER SIDE OVER SPLICING SLEEVE REINF. AND ALIGN SEAMS FOR STRAIGHTNESS.3. TACK WELD SPLICING SLEEVE REINF. INSIDE AND TACK WELD OUTSIDE SEAM AT BOTH FACES.4. CONTINUOUS WELD SEAM - GRIND AND FINISH SMOOTH.

12" (304.8)

12 GA. (1.9) SPLICING REINF.


12 GA. (2.6)FIELD SPLICING SLEEVE

ARC WELD INSIDE

ARC WELD INSIDE

FIELD SPLICE WITH BRACKETFIELD WELD & FASTEN WITH SCREWS

3" (76.2)


NOTES FOR LABELING PURPOSES:1) NOTCH SOFFIT OF ADJOINING PIECE.2) ARC WELD SPLICING SLEEVE BRACKET TO MULLION.3) FULL WELD FACES OF BOTH PIECES TOGETHER, OR

ATTACH WITH 3 #10 SCREWS THROUGH FACE INTO FIELD SPLICING SLEEVE BRACKET.


107KD Double Egress Frame Standards


May, 2010

LHANDING

LHRRH LH

RHR

DOUBLE RIGHT HAND SWING(STANDARD)

2

1

3 MEETING EDGE

5-3/4" (146.1) JAMB DEPTH HAS 7/16" (11.1) RETURN 18, 16, 14 GA.12 GA. 1/2" RETURN NO KD

2-5/8"(79.4)

4-3/4" (120.7) MIN.14" (355.6) MAX.

EQUAL

1-15/16"(49.2)

EQUAL

THROATOPENING

*1/2" (12.7)

*1/2" (12.7)

2" (50.8)

1-3/8" (34.9) 5/8" (15.9)

FINISHOPENINGWIDTH

1 JAMB

2 HEAD

THROATOPENING

1/2"(12.7)

1/2"(12.7)

2-5/8"(79.4)

4" (101.6) MIN.14" (355.6) MAX.

2"(50.8)

5/8" (15.9)

* *

*

M - FLUSH SERIES KDC - DRYWALL KD NOT AVAILABLE

3

3/32" (.094) CL HEAD

3/16" (.188)

SOFFIT STOP IS HELD BACK 3/32" TO PROVIDEPROPER DOOR CLEARANCE


108S.B.E. Double Egress Frame Corner JointsFrame Technical Data

November, 2004

L RETURN FILLER

RETURN FILLER

WELD

RETURN FILLER

VERTICAL BUTT JOINT(STANDARD)WELDED &GROUND SMOOTH

HORIZONTAL BUTT JOINT(OPTIONAL)WELDED &GROUND SMOOTH


109CCW - Open Back Rail - 10'6-5/8" Lengths


November, 2004

L

6'8" (2032) LOCATION 3 HINGES C.C.W. 24

7'0" (2133.6) LOCATION 3 HINGES C.C.W. 25


OPEN BACK RAILHINGE JAMB





OPEN BACK RAILHINGE JAMB

FOR 1-3/4" (44.5) DOORS ALL STRIKE LOCATIONS 40" (1016)IF PUNCHED - SILENCERS ARE REQUIREDWHEN ORDERING CCW 26 STRIKE JAMB SPECIFY DOOR HEIGHT

OPEN BACK RAILSTRIKE JAMB

CL

NOTE: ANCHORS ARE NOT INCLUDED WITH CCW MATERIAL. CCW MATERIAL MAY BE ORDERED CUT TO LENGTH - EXACT LENGTH - WITH S.M.O. OR S.B.E. CORNER CONFIGURATION. CUSTOM PROFILES AVAILABLE. 12 GA. FRAMES ARE CCW. 5-3/4 JAMB DEPTH HAS 1/2" RETURNS.

C.C.W. 26

10'6-5/8" (3216.3)


110CCW - Mullion Closed Section - 10'6-5/8" LengthsFrame Technical Data

November, 2004

L




MULLION - CLOSED SECTIONHINGE JAMB





MULLION -CLOSED SECTIONHINGE JAMB

FOR 1-3/4" (44.5) DOORS ALL STRIKE LOCATIONS 40" (1016)IF PUNCHED - SILENCERS ARE REQUIREDWHEN ORDERING CCW 41 STRIKE JAMB SPECIFY DOOR HEIGHT

MULLION -CLOSED SECTIONSTRIKE JAMB

CL

C.C.W. 41

10'6-5/8" (3216.3)

12 GA. FRAMES ARE CCW


111CCW - Mullion Closed Section - 10'6-5/8" Lengths

Communicating MullionFrame Technical Data

November, 2004

L10'6-5/8" (3216.3)

MULLION - CLOSED SECTIONCOMBINATION RAILALL STANDARDDOOR HEIGHTS.

DOUBLE HINGE, DOUBLESTRIKE OR HINGE ANDSTRIKE COMBINATIONS.

6'8" (2032) LOCATION 3 HINGES & STRIKE C.C.W. 45

7'0" (2133.6) LOCATION 3 HINGES & STRIKE C.C.W. 46





10'0" (3048) LOCATION OF 4 HINGES & STRIKE C.C.W. 136

DOUBLE STRIKE MULLION C.C.W. 85

NOTE: WHEN ORDERING CCW 85 SPECIFY DOOR HEIGHT.6'8" (2032) LOCATION 3 (DOUBLE HINGES) C.C.W. 86

7'0" (2133.6) LOCATION 3 (DOUBLE HINGES) C.C.W. 87





10'0" (3048) LOCATION OF 4 (DOUBLE HINGES) C.C.W. 138

NOTE: WHEN ORDERING COMBINATION MULLION DOUBLE HINGE, DOUBLE STRIKE, OR HINGE ANDSTRIKE, PROVIDE SECTION DETAIL OF DOOR RABBET LOCATION.

EXAMPLE

12 GAUGE FRAMES ARE CCW


112CCW Sills - CCW 28, 139, 140, 48, 49, 55 - 10'6-5/8" LengthsFrame Technical Data

November, 2004

L

4" (101.6)6" (152.4)8" (203.2)

JAMBDEPTH

FULL JAMB DEPTH 4" (101.6) FACE OR LESS C.C.W. 28



6-13/16" (173)

JAMBDEPTH

FULL JAMB DEPTH 6-13/16" (173) FACE C.C.W. 55

4" (101.6)6" (152.4)8" (203.2)

5/8" (15.9)

1-9/16" (39.7)

SPECIAL 1-9/16" (39.7) THICK C.C.W. 48

4" (101.6)6" (152.4)8" (203.2)

5/8" (15.9)

1-15/16" (49.2)

SPECIAL 1-15/16" (49.2) THICK C.C.W. 49

10'6-5/8" (3216.3)



113CCW - Plain Mullion CCW 16, 17, 18, 50 - 10'6-5/8" Lengths


November, 2004

L

10'6-5/8" (3216.3) 2" (50.8) FACE

JAMB DEPTH

PLAIN MULLION 2" (50.8) FACE C.C.W. 16

4" (101.6) FACE

JAMB DEPTH


6" (152.4) FACE

JAMB DEPTH


8" (203.2) FACE

JAMB DEPTH




114CCW - Plain Rail CCW 21, 23, 115, 117 - 10'6-5/8" LengthsFrame Technical Data

November, 2004

L

10'6-5/8" (3216.3)2" (50.8) FACE

JAMB DEPTH

PLAIN RAIL 2" (50.8) FACE C.C.W. 21

JAMB DEPTH


JAMB DEPTH


4" (101.6) FACE

6" (152.4) FACE

JAMB DEPTH


8" (203.2) FACE



115Sill ReinforcementFrame Technical Data

August, 2003

LANCHOR PART NUMBER: P320

LOCATED EVERY 18" OF SILL LENGTH WHEN FACE EXCEEDS 5".PROVIDES ADDITIONAL SUPPORT TO PROFILE FACE.

2" (50.8)

1-1/2" (38.1)

12 GA. (2.6)

ONE STIFFENER EVERY 18" OF LENGTH ONFACE DIMENSIONS 5" TO 9" FACE DIMENSIONS9" THRU 16" MAX. REQUIRE TWO STIFFENERSPER 18" OF LENGTH.


116CCW - Misc. Rail CCW 19, 27, 22, 29 - 10'6-5/8" LengthsFrame Technical Data

November, 2004

L

JAMB DEPTH

COVER PLATECORNER OR FLAT

10'6-5/8" (3216.3)

C.C.W. 19

FILLER PLATE WITHOUT STOP

C.C.W. 27

FILLER PLATE WITH STOP

C.C.W. 22

HEAD CAP

C.C.W. 29

JAMB DEPTH

JAMB DEPTH

JAMB DEPTH

OR

CORNER

FLAT



117CCW - Misc. Rail CCW 91, 92, 40 - 10'6-5/8" Lengths


November, 2004

L

10'6-5/8" (3216.3)

JAMB DEPTH

JAMB DEPTH

JAMB DEPTH

CHANNEL HEAD REINF.

C.C.W. 91

FULL WIDTH HEAD REINF.

C.C.W. 92

CASED OPENING PLAIN RAILCASED OPENING PLAIN RAIL 4" (101.6)

C.C.W. 40 2" FACE

C.C.W. 20 4" FACE



118CCW - Corners CCW 51, 52, 53, 54 - 10'6-5/8" LengthsFrame Technical Data

November, 2004

L

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)

2 WAY CORNER1-9/16" (39.7) OUTSIDE

C.C.W. 51

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)


C.C.W. 52

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)


C.C.W. 53

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)

1-15/16"(49.2)

1-9/16"(39.7)

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)


C.C.W. 54

JAMB DEPTH

1-15/16"(49.2)

1-9/16"(39.7)

1-15/16"(49.2)

1-9/16"(39.7)



119CCW - Glass StopFrame Technical Data

November, 2004

L

CCW# HEIGHT X WIDTH DESCRIPTION 93 5/8" (15.9) X 5/8" (15.9) PRIME PAINT - PUNCHED 12" (304.8) ON CENTER 97 5/8" (15.9) X 5/8" (15.9) PRIME PAINT - BLANK 101 5/8" (15.9) X 5/8" (15.9) NO PAINT - BLANK 105 5/8" (15.9) X 5/8" (15.9) NO PAINT - PUNCHED 12" (304.8) ON CENTER

94 5/8" (15.9) X 1" (25.4) PRIME PAINT - PUNCHED 12" (304.8) ON CENTER 98 5/8" (15.9) X 1" (25.4) PRIME PAINT - BLANK 102 5/8" (15.9) X 1" (25.4) NO PAINT - BLANK 106 5/8" (15.9) X 1" (25.4) NO PAINT - PUNCHED 12" (304.8) ON CENTER

95 3/4" (19) x 5/8" (15.9) PRIME PAINT - PUNCHED 12" (304.8) ON CENTER 99 3/4" (19) x 5/8" (15.9) PRIME PAINT - BLANK 103 3/4" (19) x 5/8" (15.9) NO PAINT - BLANK 107 3/4" (19) x 5/8" (15.9) NO PAINT - PUNCHED 12" (304.8) ON CENTER

96 3/4" (19) X 1" (25.4) PRIME PAINT PUNCHED 6" (152.4) ON CENTER 100 3/4" (19) X 1" (25.4) PRIME PAINT - BLANK 104 3/4" (19) X 1" (25.4) NO PAINT - BLANK 108 3/4" (19) X 1" (25.4) NO PAINT - PUNCHED 6" (152.4) ON CENTER

143 1" (25.4) X 1" (25.4) - PRIME PAINT - PUNCHED 6" (152.4) ON CENTER GLASS STOP IS MANUFACTURED FROM GALVANEALED STEEL. PAINT IS CURRIES STANDARD GRAY PRIME. PUNCHING IS FOR OVAL HEAD SCREWS SIZE #8.

NOTE: HOLE PUNCHING ON GLASS STOP IS STANDARD 12" (304.8) ON CENTER. IF STOP

IS TO BE USED FOR LABEL FRAME APPLICATIONS YOU MUST SPECIFY ON ORDER

THAT HOLES ARE TO BE 6" (152.4) ON CENTER.

ALL GLASS STOP AND SOFFIT STOP MATERIAL COME IN 10'6" (3200.4) LENGTHS

STAINLESS STEEL GLASS STOP IS 16 GA. (1.4)

5/8"(15.9)

5/8"(15.9)

5/8"(15.9)

1"(25.4)

3/4"(19)

5/8"(15.9)

3/4"(19)

1"(25.4)

1"(25.4)

1"(25.4)

9/32" (7.1)

16 GA.

16 GA.

16 GA.

18 GA.

18 GA.


120CCW - Shipping Spreader Bar CCW 111 - 10'6-5/8" LengthsFrame Technical Data

April, 2002

L

TACK WELD SHIPPING SPREADER BAR TO BOTTOM OFFRAME RABBET INSIDE NOMINAL FRAME OPENING.

TOP VIEW LOOKING DOWN

3/8" (9.5)

1" (25.4)

NOTE: CURRIES HOLLOW METAL FRAMES HAVE DOUBLE SHIPPING SPREADER BARS WELDED ON THE BOTTOM. THE SPREADER BARS MUST BE REMOVED AND A SETTING SPREADER USED FOR FINAL INSTALLATION. A COLD CHISEL AND HAMMER ARE RECOMMENDED TOOLS TO USE TO REMOVE THESE. THE FRAME INSTALLER ASSUMESALL RESPONSIBILITY FOR PLUMB FRAME INSTALLATION.


121Custom Frame Profiles

Frame Technical DataFebruary, 2016

LCONTACT FACTORY FOR CAPABILITIES

3/4” (19.1)MINIMUM

1” (25.4)MINIMUM

1/2” (12.7)MINIMUM

289 3/4” (19.1)MINIMUM

1” (25.4)MINIMUM

1/2” (12.7)MINIMUM

B

3/8” (9.5)MINIMUM

VARIES

VARIES

1/8” (3.2) 16 GA. (1.4)MINIMUM

F

5/32” (4) 14 GA. (1.9)MINIMUM

NOTE: FOR 12 GA. (2.6) CONTACT FACTORY


122Custom Frame ProfilesFrame Technical Data

March, 2017

L

3/4” (19.1)MINIMUM

1-1/2” (38.1)MINIMUM4” (101.6)MAXIMUM

2” (50.8) MINIMUM 4” (101.6) MAXIMUM

2” (50.8)MAXIMUM

MH1/2” (12.7)MINIMUM

NOTE THROAT OPENING WHEN ORDERING

1/2” (12.7) RADIUS ONLY

1/2” (12.7)

3/4” (19.1)MINIMUM

1” (25.4)MINIMUM

2” (50.8)MAXIMUM

L

1/2” (12.7)MINIMUM

1/2” (12.7)

3/8” (9.5)MINIMUM

3/4” (19.1)MINIMUM

1” (25.4)MINIMUM

1/8” (3.2) 16 GA. (1.4)3/16” (4.8) 14 GA. (1.9)

INOT 12 GA. (2.6)

16 GA. ONLY

1/2” (12.7)ONLY

1/2” RADIUS

1/4” (6.4)ONLY

275 4” MIN. (101.6)9-3/4” MAX. (247.7)

4” MIN. (101.6)9-3/4” MAX. (247.7)

2” (50.8)MAXIMUM

1/2” (12.7)MINIMUM

NOTE THROAT OPENING WHEN ORDERING

16 GA. ONLY


123Mercury Thermal Break Frame KD Flush Profile

Frame Technical DataJanuary, 2017

L3-3/4” (95.3) THRU 5-5/8” (142.9) JAMB DEPTH AVAILABLE SINGLE RABBET14 GA. (1.9) AND 16 GA. (1.4) GALVANEALED STEEL5/8” (15.9) HIGH STOP ONLYKD, FACE ONLY WELD, OR FULL WELDMAXIMUM KD LENGTH - 8’0” JAMB, 8’0” HEADPUNCH FOR SILENCERS NOT AVAILABLE

ANCHOR OPTIONS: WIRE ANCHOR SPLIT BASE ANCHOR SPLIT WOODSTUD ANCHOR EXISTING WALL ANCHOR

NFRC 102 U AND R VALUES STANDARDIZED THERMAL TRANSMITTANCE MERCURY FRAME & TRIO-E FLUSH DOOR - U VALUE 0.36, R VALUE 2.65 MERCURY FRAME & FRP FLUSH DOOR - U VALUE 0.39 MERCURY FRAME & MERCURY FLUSH DOOR - U VALUE 0.37 R VALUE 2.53

NFRC 400 AIR INFILTRATION (CFM/SQ FT) MERCURY FRAME & TRIO-E FLUSH DOOR - 0.5 MERCURY FRAME & FRP FLUSH DOOR - 1.0 MERCURY FRAME & MERCURY FLUSH DOOR - 0.5

1” (25.4) THRU 2” (50.8) OR 4” (101.6)FACE

DOOR RABBET

THERMAL BREAK

5-3/4” (146.1)THRU 14” (355.6)

JAMB DEPTH

THERMAL BREAK

DOORRABBET

1” (25.4) THRU 2” (50.8) FACE

PEMKO S44 SHIPS LOOSE WITH FRAME,TO BE FIELD INSTALLED AFTER FINISH PAINT.


124Mercury Thermal Break Frame CCW Stick ComponentsFrame Technical Data

September, 2016

L16 GA. (1.4) AND 14 GA. (1.9) GALVANEALED STEEL ONLY5/8” (15.9) HIGH STOPS ONLY BUTT END JOINTS ONLYNOT LABELED

MERCURY U VALUE - 0.37MERCURY R VALUE - 2.70

MULLION - 16 GA. (1.4) AND 14 GA. (1.9) PUNCH FOR SILENCERS NOT AVAILABLE.

THERMAL BREAK

THERMAL BREAK

5-3/4” (146.1)THRU 14” (355.6)

JAMB DEPTH

3-3/4” (95.3) THRU 5-5/8” (142.9) JAMB

DEPTH AVAILABLE SINGLE RABBET

THERMAL BREAK


125Notes


February, 2009


126Steel Channel Anchor Installation


November, 2014

L

TWIST 45˚ TOCLEAR THE RETURNS.

TWIST THE ANCHORUPRIGHT.

ROTATE THEANCHOR CLOCKWISE TOTIGHTEN IN THEPROFILE.

ROTATE TO GET THEANCHOR LEGSUNDER THE PROFILE RETURNS.

ROTATE ANCHOR 45˚TO CLEAR RETURNS.SLIDE INTO PROFILE.


127Door Silencers


October, 2002

TOP OFSTRIKECUTOUT

SILENCERS

8" (203.2)

10" (254)

2" (50.8)

SINGLE DOORFRAME

SILENCERS

CL

5" (127)

5" (127)

PAIR OF DOORS FRAME

ADHESIVE TYPE

ADHESIVE BACKED SILENCERSFIELD APPLIED AFTER FINISH PAINTING

PUNCH TYPE

17/64" (6.8) DIA. HOLETO ACCEPT PUSH IN

TYPE SILENCERS

17/64" (6.8) 5/8" (15.9)

ADHESIVEBACKING


128Loose Spline SleeveFrame Technical Data

September, 2003

JAMB DEPTH-5/16" (7.9)

4" (101.6)

PART #P20016 (1.4) GA.

4 SPOTWELDS

16 GA. (1.4)

PART #P200

L


129KD Frame Assembly Instructions


September, 2011

NOTE ON WELDED FRAMES: Shipping bars should NOT be usedas spreader. Remove shipping barbefore setting frame.

Plumbing the frame

The contractor should beequipped with a carpenter level,square and spreader. Set theframe in desired location andlevel the header. Square jambsto header. Shim under jambs ifnecessary. With frame in place,set spreader and fasten jambsto floor through floor anchors.

BRACING FRAMES BEFORE WALL CONSTRUCTION FOR KD AND WELDED FRAMES

MASONRY FRAMES, THERMAL BREAK, AND CURRISEAL FOR MASONRY, METAL STUD, AND WOOD STD WALLS

Bracing the frame

Brace the frame as shown or shoreto a structure above. Brace in the direction of intended wall. Plumb andsquare jambs. Install vertical brace tosupport header for openings over4'0" wide.

Squaring the Frame

The installer should use wood spreaders (as described below), a carpenterslevel (the longer the better), and a full size carpenters square. Set the frame in the desired location. Level head and plumb jambs. Shim under jambs ifnecessary.

Job Storage

Store frames off the ground on wood runners or skids. Do not store directly on the ground.Cover frames with tarpaulin or plastic but do insure that adequate ventilation is provided toeliminate moisture condensation. When frames are to be fully grouted and when plaster or mortar contain "anti-freeze" agents, the inside of the frames should be coated with a bituminous, water-resistant paint by the installation contractor.

Spreader

Typical wood spreader must be square and made from lumber atleast 1” thick. Length of spreader equals door opening width at thehead. Cut clearance notches for frame stops as shown. Spreadermust be nearly as wide as frame depth for accurate installation.

Assembly of Frame Plumbing of Frame

Spreader

Typical wood spreader must be square and fabricated fromlumber no less than 1" thick. Correct length is the dooropening width between the jambs at the header (i.e., SingleDoor 3'0" = 36"). Cut clearance notches for frame stops.Spreader must be nearly as wide as frame depth for accurate installation.

LEVEL

#8 SCREW(MS002485)(REQUIRED ON ALL KD APPLICATIONS)

HEAD

JAMB

A A SECTION A-A

SPREADER

PLUM

B

SQUARE

DOOR OPNG. AT HEADER

FRAM

EDE

PTH


130KD Frame Assembly InstructionsFrame Technical DataSeptember, 2011

NEW MASONRY CONSTRUCTION FOR KD AND WELDED FRAMES

Wire

Anchor

“T”

Anchor

STEEL STUD WALL CONSTRUCTION WITH FLUSH OR RECESS TYPE ANCHORS FOR KD AND WELDED FRAMES

Elevation

1. Assemble frame.2. Install anchors. Position anchors in frame through the throat and tap in with a hammer. Frames may also be supplied with anchors welded in place.

3. Square, brace and plumb frame as shown.4. Set spreader. Attach jambs to floor through floor anchor or floor extension. Install jamb studs to floor and ceiling runners and tightly against frame anchors.

5. Attach studs to frame anchors as shown below.

NOTE: Drywall must extend at least 1/2" into frame at fire rated installations.

Channel type steel stud

Position studs in frame throat and attach to anchors with screws or weld. If using screws,the installer should drill from the back side of the stud, through both the stud and anchor,then attach with (2) screws per anchor location.

NOTE: When attaching header stud to jamb studs, be sure the stud is above frame header.This will assure ample room for attaching plaster lath or drywall and will not interfere withinstallation of hardware attached to frame header. Anchors are not required in frame heads,except fire listed double egress openings.

90˚ 90˚

HEADER STUD

JAMBSTUD

JAMBSTUD

SPREADER

FRAME

CHANNELTYPEJAMB STUDS

1. Assemble frame.2. Set brace and plumb frame.3. Install anchors. Grout frame in the area of the anchors as block courses are laid up. Frames may also be supplied with anchors welded in place.4. A second spreader is recommended at the mid point of the door opening to maintain the door opening dimension.5. Continually check plumb and square as wall progresses.

Existing Masonry Construction

1. Drill (4) 9/16" diameter holes evenly spaced in each jamb for 3/8" expansion shell anchors. Install multipurpose anchor at each 9/16" hole.2. Assemble 3 frame pieces flat on floor. Install (4) #8 x 1/2" sheet metal screws (included) at corners of head to each jamb (required for Underwriters Laboratories fire rating). Locate removable spacing bar at base of frame to maintain proper opening width during installation.3. Position assembled frame in opening. Plumb and level the frame. Shim frame as required.4. Anchor frame to wall with 3/8" expansion shell anchors, shimming behind anchors as needed.

NOTE: Anchors in frame heads are not required.

90˚ 90˚

SPREADER


131KD Frame Assembly Installation


September, 2011WOOD STUD CONSTRUCTION FOR KD AND WELDED FRAMES

WOOD STUD CONSTRUCTION (STUDS ERECTED BEFORE FRAME)

Erect frame

Assemble frame. Stand frame up in desired location.Anchor one jamb to floor and set spreader on floorfrom anchored jamb to loose jamb. Plumb, level, andsquare frame. Position and anchor second jamb, then brace.

NOTE: Drywall must extend at least 1/2" into frameat fire rated installations.

1. Install anchors. Position anchors in frame throat and tap in with a hammer. Frames may also be supplied with anchors welded in place.2. Set spreader. Attach jambs to floor through floor anchor or floor extension. Install double jamb studs to floor and ceiling runners and header.3. Bend anchor tabs around stud leaving desired clearance between frame return and stud for inserting finished wall material.4. Square and nail top anchor to stud on ONE JAMB ONLY. Check plumb and square and continue to nail balance of anchors to stud. Repeat for opposite jamb.5. Anchors are not required in frame heads, except fire listed double egress openings.

Rough opening

Build rough opening. Rough opening dimensionsfor 2" face frames should be 4-1/4" - 4-1/2"larger than door width and 2-1/4" - 2-1/2"larger than door height. It is recommended thatdouble studs be used at jambs and headers.

NOTE: Drywall must extend at least 1/2" intoframe at fire rated installations.

1. Assemble frame.2. Install anchors. Position anchors in frame throat and tap in with a hammer. Frames may also be supplied with anchors welded in place. Base anchors may also be used. If base anchor cannot be used add one anchor per jamb at bottom.3. Place frame in rough stud opening.4. Bend anchor tabs around stud leaving desired clearance between frame return and stud for inserting finished wall material.5. Set spreader and level frame. Shim jambs if necessary.6. Square and nail top anchor to stud on ONE JAMB ONLY. Check plumb and square and continue to nail balance of anchors to stud. Repeat for opposite jamb.7. Anchors are not required in frame heads, except fire listed double egress openings.

ANGLEBRACES

SPREADER

FRAME

WOODSTUDS

FLOORRUNNER

JAMBSTUD

HEADER STUD

SPREADER

90˚ 90˚

ROUGHOPENING

DIMENSIONS

SPREADER

90˚

WOODSTUDS

FRAME

90˚


132

NotesFrame Technical Data

August, 2017


133Security Sidelite Door Construction


March, 2007

FEATURES:

HINGED SECURITY PANEL CLOSES TO CREATE AVISUAL BARRIER

GLASS POCKETS AVAILABLE FOR UP TO 1” THICKGLASS

PREPARED FOR SELF LATCHING DEADBOLT TOMEET PROJECT REQUIREMENTS

STANDARD 4-1/2” X .134 HINGE PREPARATIONS

OPTIONS:

AVAILABLE WITH MASONRY AND STUD WALL ANCHORS

FIRE RATING:WARNOCK HERSEY3/4 HOUR RATING. (1-1/2 HOUR WITH SPECIALTY GLAZING)

USES:• CLASSROOMS• POST OFFICES• GOVERNMENT FACILITIES• AIRPORTS

16 OR 14 GA. FRAMES WITHWELDED CORNERS 6-3/4" MINIMUM DEPTH

OPERABLEPANEL

INSIDESECTIONOUTSIDE

GLASS

HORIZONTAL ASTRAGAL REQUIRED.

PANEL - RATED - HONEYCOMB AND MINERAL CORENON-RATED - STEEL STIFFENED AND POLYSTYRENE

FRAME - 3 HR MAX. RATING11'4" MAX. HEIGHT4' MAX. WIDTH SINGLE8' MAX. WIDTH PAIR


134Transom Frame Removable Panel Installation


April, 2012

L

16 GAUGE GUIDE CHANNEL

TOP OF PANEL NOTCHEDFOR GUIDE CHANNELS

BOTH FACE SHEETSWELDED TO VERTICAL END CHANNELS, 6" O.C.

3/8" RETAINER PINS FOR REMOVABLE PANELS: WELDED TOINSIDE OF HEAD.6" FROM ENDS 18" MAX O.C.

TAPPED FOR 1/4-20 MS

1/4" STEEL PLATE

HORIZONTAL EDGES OF PANEL AREWELDED TO CONTINUOUS CHANNEL

NOMINAL 1-3/4" THICK

1/4" STEEL PLATE WITHCLEAR HOLE

16 GAUGE GUIDE(END) CHANNELSBOTH SIDES

1/4-20 FHMS (2)

JAMB

TOP OF PANEL

BOTTOM OF PANEL

1-9/16"

7/8"

DRILL 1/4" AND COUNTERSINK

DOOR OPENING17/32" TO BOTTOM OFPANEL & 1/8" CLEARANCETO TOP OF DOOR FROM BOTTOM OF PANEL

48" MAX.PANELHEIGHT

NOTE: PANEL AND TRANSOM FRAME REQUIRE SPECIAL CONSTRUCTION. MUST BE INDICATED ON BOTH DOOR AND FRAME ORDER.


135Slip-on “N” Profile Door Frame

Frame Technical DataMay, 2018

INSTALL WITH NAILER HOLES IN FACE. AVAILABLE WITH OR WITHOUT COMPRESSION ANCHORS.

L

FIRE LABEL NOTES: WOOD TRIM SHALL BE APPLIED TO FRAME FACES WITH A FIRE LISTED CONTACT ADHESIVE AND /OR FAST CAP 2P-10 ADHESIVE. WOOD TRIM MUST BE HELD BACK FROM THE CORNER OF THE FRAME FACE (CLOSEST TO THE DOOR RABBET) APPROXIMATELY 1/4” - 3/8” .

N PROFILE STANDARD WILL BE COMPRESSION ANCHORS AND NAIL HOLES ON BOTH SIDES.NM PROFILE WILL NOT HAVE COMPRESSION ANCHORS. ANCHORS (WELDED IN ONLY) AND NAIL HOLES NEED TO BE SPECIFIED.

TABS

SLOTS

COMPRESSION ANCHOR DRIVER ACCESS HOLE

JAMBHEAD CORNER ASSEMBLY

COMPRESSIONANCHOR(OPTIONAL)

(HEIGHT)SEE CHART

WIDTHSEE CHART

2”

THROAT *

* ORDER USING JAMB DEPTHJAMB DEPTH = THROAT DIMENSION +1/8

FASTENER ATTCHMENT HOLES PUNCHED IN EACH FACE COMPRESSION AN-

CHOR OPTIONAL

SPECIFICATIONS:MAXIMUM SINGLE – 4’0” (1219) W X 9’-0” (2743) HMAXIMUM PAIR – 8’0” (2438) W X 9’0” (2743) H (NO DOUBLE EGRESS)THROAT – 3-3/4” (95) MIN TO 13” (330) MAX 3F ONLY.SINGLE AND DOUBLE RABBET ONLY (NO KERF)GAUGE: 16 GA. (1.5) MIN, 14 GA (1.8) MAX MATERIAL: COLD ROLLED OR GALVANNEALED STEELATTACHMENT HOLES: HOLES ARE LOCATED AT 16” MAX SPACING AND 2” MAX FROM ENDS.


136Slip-On Hybrid Drywall Door FrameFrame Technical Data

May, 2018

L

TABSLOT

CORNER CLIP

90 MINUTE MAXIMUM RATING(INTERTEK ONLY)

HEAD

JAMB CORNERASSEMBLY

COMPRESSIONANCHOR

COMPRESSIONANCHOR

PUNCH AND DIMPLE ON DRYWALL RETURN SIDE

THROAT

2” (49)

SPECIFICATIONS:MAXIMUM SINGLE – 4’0” (1219) W X 9’-0” (2743) HMAXIMUM PAIR – 8’0” (2438) W X 9’0” (2743) H (NO DOUBLE EGRESS)THROAT – 3-3/4” (95) MIN TO 13” (330) MAX 3F ONLY.SINGLE AND DOUBLE RABBET ONLY (NO KERF)GAUGE: 16 GA. (1.5) MIN, 14 GA (1.8) MAX MATERIAL: COLD ROLLED OR GALVANNEALED STEELATTACHMENT HOLES: HOLES ON THE “NO RETURN” SIDE LOCATED AT 16” MAX SPACING AND 2” MAX FROM ENDS.


137Drywall KD SideLight

Frame Technical DataMay, 2012

L

LAUQE

:SETON .SELIFORP EDISTUO NO NOITCURTSNOC DK.1

DETACOL EB OT ROHCNA NOISSERPMOC ARTXE.BMAJ THGILEDIS FO MOTTOB EHT TA

TA DAEH OT DEDLEW EB OT PURRITS NOILLUM.2.DERETNEC NOILLUM ROF HCTON

DEDLEW EB OT PILCTOOF DEDLEW ESREVER.3.AERA LLIS REDNU NOILLUM OT

HCTON POTS A SERIUQER NOILLUM LACITREV.4.POT TA

"Z" THGIL EDIS DK ROF DAEH NO HCTON ROF.5.)"521. - EZIS ECAF( HCTON

BASE ANCHORS

COMPRESSION ANCHORS

KNOCK DOWN (KD)CONNECTION

MULLIONSTIRRUP

STOPNOTCH

MULLION

HEAD

Z-NOTCH

MULLION

SILL

REVERSE WELDED FOOTCLIP

DRYWALL “C” PROFILE16 GAUGE ONLY2” FACE STANDARD – 1-1/2” AND 1-3/4” AVAILABLEJAMB DEPTHS – UNEQUAL RABBET - 4-1/2” THROUGH 8-3/4” EQUAL RABBET - 4-7/8” THROUGH 8-3/4”SILL FACE 1-1/2” THROUGH 6” AVAILABLECOMPRESSION ANCHORSBASE ANCHORS – 2” FACE HAS STANDARD BASE ANCHOR (PUNCH FACE) 1-1/2” AND 1-3/4” FACE HAS OPTIONAL BASE ANCHOR4’0” X 8’0” MAXIMUM DOOR OPENING8’0” X 8’0” MAXIMUM ELEVATION OPENING SIZEAVAILABLE IN SINGLE AND DOUBLE (SAME SIDE) SIDELIGHT NO HORIZONTAL MULLIONS ALLOWEDSINGLE DOOR OPENING ONLYNON-RATED ONLY

ROUGH OPENING REQUIREMENTS:THE ROUGH OPENING HEIGHT EQUALS THE FINISHED OPENING HEIGHT +1”.

THE ROUGH OPENING WIDTH EQUALS THE FINISHED WIDTH +2”.


138ElectroLynx® System LX OptionsFrame Technical Data

The CURRIES LX cable is equipped with the ElectroLynx® System of “plug-in” connectors for fast, easy, connection to similarly equippedASSA ABLOY Hardware. The LX cable has 15 conductors of 22 gauge wire in a PVC jacket, with ElectroLynx snap connectors on the hardwareprep end only. Ship loose only. Power over Ethernet (PoE) cabels are also available.

– Check anchor interference with conduit, some loose anchor styles won’t work.– Some electric preps won’t allow 1/2" drywall penetration for fire rated frames.– Conduit is to be supplied and installed by others.

“Hardwiring Made Easy”

April, 2011

CURRIES Tech Data Frame Section Revised open/sections... · ASSA ABLOY, the global leader in door opening solutions i Index Frame Technical Data August, 2017 DESCRIPTION PAGE(S) Anchors

Documents