1 CDA_RIGGER CURRICULUM DEVELOPMENT ADVISORY Rigger Course Version 1.0 1 May 2011 Workplace Safety and Health Council, Ministry of Manpower, Singapore (MOM) All rights reserved. This document is provided for explicit use and guidance of MOM Accredited Training Providers as information resource for curriculum development and assessment purposes. Any other use of this document or parts thereof, including reproduction, publication, distribution, transmission, retransmission or public showing, or storage in a retrieval system in any form, electronic or otherwise, for purposes other than that expressly stated in this advice without the expressed permission of MOM is strictly prohibited.
38
Embed
CURRICULUM DEVELOPMENT ADVISORY · 2014-09-30 · CURRICULUM DEVELOPMENT ADVISORY Rigger Course Version 1.0 1 May 2011 Workplace Safety and Health Council, Ministry of Manpower, Singapore
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1 CDA_RIGGER
CURRICULUM DEVELOPMENT ADVISORY
Rigger Course
Version 1.0
1 May 2011 Workplace Safety and Health Council, Ministry of Manpower, Singapore (MOM)
All rights reserved. This document is provided for explicit use and guidance of MOM Accredited Training Providers as information resource for curriculum development and assessment purposes. Any other use of this document or parts thereof, including reproduction, publication, distribution, transmission, retransmission or public showing, or storage in a retrieval system in any form, electronic or otherwise, for purposes other than that expressly stated in this advice without the expressed permission of MOM is strictly prohibited.
2 CDA_RIGGER
Version History
Version Effective Date Changes Author
1.0 01 May 2011 First issue ICB, WSH Council Office
TABLE OF CONTENTS
Page
1 Aim of the advisory 3
2 Scope of the course 3
3 Overview of the course requirements 3
4 Table of specifications 4
5 Training delivery advisory 5
6 Assessment advisory 8
7 Trainer and assessor requirements 11
8 End of course evaluation and feedback 11
9 Related WSH legislations, industrial codes of practice and other references
12
Annex A – Course Syllabus
Annex B – Table for Specifications
Annex C – Course Reference Matrix
Annex D – Sample Assessment Plan
3 CDA_RIGGER
1 AIM OF THE ADVISORY 1.1 The Curriculum Development Advisory (CDA) is a document to assist MOM Accredited Training Providers (ATP) with the instructional design and development of a competency-based training course for Workplace Safety and Health. It aims to help ATP facilitate the learning process, deliver effective training and conduct competency-based training and assessment. 1.2 This document contains key information on the Rigger Course including the course aim, learning objectives, target audience, assumed skills and knowledge/entry requirements, course syllabus, recommended course duration, recommended class size, and recommended trainer/trainee ratio. It also sets forth guidelines for training delivery and assessment for the course.
1.3 This CDA will be reviewed on a regular basis and whenever it is deemed necessary due to changes in training syllabus or industrial requirements.
2 SCOPE OF THE COURSE 2.1 The Rigger Course is aimed at providing individuals with the knowledge and skills to prepare and tie the load for safe lifting by any form of lifting equipment. It is a mandatory course for individuals who are assigned to carry out preparation of the load for lifting operation involving a mobile crane or tower crane. 2.2 Factories (Operation of Cranes) Regulations stipulates that:
“No person shall rig up loads for any lifting operations by a mobile crane or tower crane unless he is a rigger appointed by an occupier” “No person shall be appointed as rigger unless he has successfully completed a training course approved by the Chief Inspector” (Commissioner of Workplace Safety and Health) “A rigger who is appointed….shall be attired in such a way as would distinctively identify him as a rigger”
3 OVERVIEW OF THE COURSE REQUIREMENTS 3.1 Learning objectives for the Rigger course:
3.1.1 List the duties of the Rigger in lifting operations
3.1.2 Comply with safe work procedure for lifting
3.1.3 Participate in toolbox meeting
3.1.4 Estimate load and determine centre of gravity
4 CDA_RIGGER
3.1.5 Conduct pre-lift inspection of lifting gear and accessories
3.1.6 Select the appropriate rigging equipment
3.1.7 Rig and direct load to destination with safe lifting
3.1.8 Check and verify load is properly rigged
3.1.9 Apply 3-step lifting and lowering method
3.1.10 Practise good housekeeping of lifting gear and accessories
3.1.11 Identify hazards related to lifting
3.1.12 Respond to lifting accident and emergencies
3.2 Target audience:
The course would be appropriate for individuals assigned as Rigger in the workplace
3.3 Assumed skills and knowledge:
3.3.1 Workplace literacy and numeracy Level 2 or equivalent 3.3.2 At least six months relevant industrial experience
3.4: Entry requirement: 3.4.1 Must be over 18 years of age 3.5 Course syllabus: See Annex A 3.6 Recommended course duration: 16 hours including 3.5 hours of assessment 3.7 Recommended class size: Max: 16 3.8 Recommend trainer/trainee ratio: 1: 16 3.9 Course attendance record: 100% attendance 4. TABLE OF SPECIFICATIONS (TOS) 4.1 The table of specifications is a detailed listing of the course content to be covered in the training and the weightage of assessment that will be devoted to each of the learning objectives. It is a structured format based on the cognitive domain of Bloom’s taxonomy. 4.2 Refer to Annex B for details of TOS
5 CDA_RIGGER
5 TRAINING DELIVERY ADVISORY 5.1 Trainer’s guide and trainees’ workbook/handouts
5.1.1 The ATP is required to prepare a trainer’s guide for the course. The guide provides the trainer with information on the course including
� Course aim � Learning objectives � Target audience � Assumed skills and knowledge � Course duration � Class size and trainer/trainee ratio � Lesson plan � Course contents and instructional materials � Training methodologies � Training resource requirements � Course administration instruction
5.1.2 The ATP can also facilitate the learning process by providing each trainee with a trainee’s workbook or handouts. It is recommended that a Summary of Learning should be attached at the end of each unit/topic, where necessary. This set of notes should contain the course aim, learning objectives and the key learning points WSHA 2006, subsidiary legislations, industrial code of practice, as well as safety guidelines.
5.1.3 The ATP is required to prepare and submit a course reference matrix (See Annex C) for coverage of course contents with respect to the training slides and the assessment modes. 5.1.4 It is the responsibility of the ATP to ensure that no part of the materials used for the training infringe on patent, design, copyright and intellectual property rights of any individual or organization. 5.1.5 The ATP shall retain an updated version of the training course syllabus, lesson plan, trainer’s guide and trainee’s workbook or handout at all times for inspection and verification by MOM.
5.2 Training methodology
5.2.1 Knowledge The knowledge component of the Rigger course is primarily focused on the legislative requirements relating to safe lifting operations, planning and preparation and well as the practical aspects of load rigging. It includes � Duties of the Rigger in lifting operations
� Safe work procedure for lifting
6 CDA_RIGGER
� Conduct of toolbox meeting for lifting operations
� Estimation of load and determination of centre of gravity
� Checklist for pre-lift inspection of lifting gear and accessories
� Selection of appropriate rigging equipment
� Rigging methods and techniques for safe lifting
� Checking and verification of load
� 3-step lifting and lowering method
� Good housekeeping of lifting gear and accessories
� Hazards related to lifting
� Emergency procedures
5.2.2 The knowledge component may be delivered in a classroom using lectures. To enhance learning, the following delivery methods can also be used to supplement the lectures: � Case studies (with or without video)
� Group discussion
� Training videos
� Internet and other e-resources
� Posters and signboards
5.2.2 Skill In terms of skills, the trainees must proceed outdoor or on-site for demonstration and practice. The demonstration and practice must include eight key skills set:
� Participation in toolbox meeting
� Estimating load and determining centre of gravity
� Conducting pre-lift inspection of lifting gear and accessories
� Selecting appropriate rigging equipment for the lift
� Rigging methods and techniques
� Checking and verifying the load is properly rigged
� Applying 3-step lifting and lowering method
� Good housekeeping practice of lifting gear and accessories
5.2.3 Attribute Accidents can happen very fast at the worksite. A competent Rigger must have a very high sense of “situational awareness”. At all times he must
� Be aware of all movements within the zone of lifting operations
� Keep an eye constantly on the Centre of Gravity of the load
7 CDA_RIGGER
� Be quick to alert the crane operator and lifting supervisor of any hazard or danger
5.3 Training venue requirements
5.3.1 Classroom - The ATP shall ensure that the classroom used for this Rigger training has adequate seating for the class of 16. Seating facilities inclusive of writing tables must be reasonably and comfortably spaced so as to be conducive to the learning process and for the purpose of conducting the assessment. Classrooms must be equipped with projectors, whiteboards, and flipcharts. The classroom must have adequate lighting and ventilation. Emergency exit routes must be clearly marked out and briefed to the course trainees at the start of the course. 5.3.2 Practice area - Demonstration and practice of rigging must be conducted out of the classroom. The ATP is required to submit the site plan for practical training comprising a mobile crane or an overhead crane or A-frame crane no less than 1-ton safe working load (SWL). The crane must enable the trainee to rig at least 5 types of loads and direct the load to another location no less than 3 metres apart. The substitution of hands-on rigging with model cranes will NOT be accepted. 5.3.3 Standard Loads - ATPs are required to make provisions for at least five standard types of loads to be used for the training. These may include: � Skip
� Valve
� Motor
� Propeller
� Oil drum
� Pallets
� Concrete beam
� Bundle of pipes
� BRC wire mesh
� Metal scaffold frame � Rectangular steel plate � L-shape slab or L-shape pipe
5.3.4 Rigging accessories – ATPs should provide a selection of slings, shackles, chokers and other rigging accessories to allow trainees adequate exposure to the range of rigging equipment in their appropriate industry.
8 CDA_RIGGER
5.3.5 ATPs shall carry out risk management of the site used for demonstration and practice. Trainees should be briefed on the risk of the training prior to the conduct of training.
5.4 Training resource allocation
5.4.1 In the classroom, models of crane and different types of loads may be used to supplement training in the following way: � Illustrate Centre of Gravity of irregular loads
� Highlight important points in safe lifting
� Highlight hazards related to lifting of different loads
� Emphasize the key points in checking and verifying that loads are properly rigged for lifting.
5.4.2 Training centres should also make the following documents available for reference. � Workplace Safety and Health Act 2006
� WSH (General Provisions) Regulations 2006
� WSH (Construction) Regulations 2007
� Factories (Operation of Cranes) Regulations
� SS 497 Design, safe use and maintenance of overhead travelling cranes
� SS 536 :Safe Use of Mobile Cranes
� SS 559 : Code of Practice for safe use of tower Cranes
� Photos/slides of the various types of crane operations
� Safety and health posters relating to lifting operations
� Case studies relating to crane accidents
� Organizational SOPs for Rigger attire
6 ASSESSMENT ADVISORY 6.1 General guidelines for conducting competency-based assessment.
6.1.1 The ATP is required to prepare an assessment plan (see Annex D for sample) for the Rigger Course. The aim of the assessment plan is to determine the competency of the trainee to undertake the role of a Rigger upon completion of the course.
6.1.2 The assessment plan must be directly related to all the learning objectives determined in the course. It comprises four main parts:
� Overview of the assessment tools and its duration � Instructions for the conduct of the assessment � Instruments or tools of assessment (Question paper, checklist ) � Assessment summary record
9 CDA_RIGGER
6.1.3 The assessment plan is subject to review on an annual basis by the ATP to ensure that trainees are constantly kept current and competent to perform up to the industrial requirements.
6.2 Principles of assessment
Assessment will be fair, valid, reliable and flexible for all trainees without deliberate barriers against the individual.
� Fair – Are the assessments criteria clear? Do all the trainees know
what to expect from the assessment? Does the assessment disadvantage any trainee? Do the trainees have any recourse to appeal?
� Valid – Are the assessment methods and tools appropriate and effective in assessing what they claim to assess. Are the evidence collected relevant to the training and demonstrates that the learning outcome has been achieved?
� Reliability – Are the results consistent from one assessment to another? Do people have the confidence that the standards are applied consistently from learner to learner and from context to context?
� Flexibility – Can the assessment be used for multiple assessments? Are the assessment tools and methods uniform across different approaches and drawing on a range of different methods? Can they be used appropriately to the context, task and individual under assessment?
6.3 Assessment tools and instruments
6.3.1 The ATP must conduct a Written Test and Practical Performance:
� Written test (WT) – This method of assessment is quick and the
most convenient for the knowledge test. It can be used for a large class particularly to assess the knowledge component of the Rigger course.
� Practical Performance (PP) – This method is highly recommended for Rigger skills assessment. It can be matched very closely to the actual task to be performed by the individual on the job.
6.3.2 The total allocated time for assessments (WT and PP) is 3.5 hours, comprising 30 mins for Written Test and 3 hours for Practical Performance, as follows:
10 CDA_RIGGER
� Written Test The written test shall comprise 20 MCQs with pass criteria of 60%.
� Practical Performance The Practical Performance comprises assessment based on rigging of at least two different types of loads from the standard loads in paragraph 5.3.3. The pass criteria is 100%.
6.3.3 Trainees must meet the pass criteria for all the assessments to be considered to be successfully completed the Rigger Course. No re-sit for any assessment is allowed unless the trainee has attended the course again.
6.4 Briefing to trainee
6.4.1 The briefing to trainee is to explain the purpose and context of assessment so as to ensure that there are no surprises during the conduct of assessment.
6.4.2 The briefing to trainee should include
� the assessment requirements and process, including clear instructions on each of the assessment to be taken
� trainee’s rights & process of appeal to assessment outcome
6.4.3 During the briefing, assessors must take the opportunity to
confirm with trainee on any special needs & explain how needs will be addressed during assessment. 6.4.4 Assessor must seek feedback and clarify trainee’s understanding of assessment requirements before commencement of the assessment.
6.5. Conduct of assessment 6.51 Assessment must be conducted strictly in accordance with the
assessment plan. In particular, each trainee must complete all the assessment requirements in the time allocated. .All safety procedures must be complied.
6.5.2 A judgment on the competency of the trainee must only be
made based on the evidence gathered. The evidence for each of the assessment instrument is given in the suggested response to the WT and the checklist accompanying the PP.
6.6 Recording and reporting of assessment outcome 6.6.1 All assessment outcomes must be accurately recorded in the
assessment summary record form. 6.6.2 Assessment outcome will be communicated to the trainee.
11 CDA_RIGGER
6.6.3 The ATP shall maintain a record of the assessment results for 2
years for audit by MOM. 7 TRAINER AND ASSESSOR REQUIREMENTS A trainer and assessor of this Rigger course should possess all of the following:
� WSQ Advanced Certificate in Workplace Safety and Health (WSH Professional Level B) or equivalent
� Lifting Supervisor Safety Course certification
� At least 5 years experience as a supervisor/foreman/safety personnel in lifting operations
� Advanced Certificate in Training and Assessment (ACTA) or equivalent
8 END OF COURSE EVALUATION AND FEEDBACK 8.1 The ATP shall conduct an end-of-course evaluation at the end of each course. Trainees shall be allowed to provide quantitative and qualitative feedback on the course content, duration, training delivery, training materials, training venue, training resources, quality of trainers and assessors. 8.2 The ATP shall monitor the end-of-course evaluation and feedback closely to ensure that the ratings are consistently 3 and above. Immediate action should be taken whenever the ratings fall below 3. These actions should be properly recorded and kept for audit inspection.
1 2 3 4 5 Poor Fair Satisfactory Very good Excellent
12 CDA_RIGGER
9 RELATED WSH LEGISLATIONS, INDUSTRIAL CODE OF PRACTICE AND OTHER REFERENCES (the list is not exhaustive)
� Workplace Safety and Health Act 2006
� WSH (General Provisions) Regulations 2006
� WSH (Construction) Regulations 2007
� Factories (Operation of Cranes) Regulations
� SS 497 Design, safe use and maintenance of overhead travelling
cranes
� SS 536 :Safe Use of Mobile Cranes
� SS 559 :Code of Practice for safe use of tower Cranes
� Technical Advisory on Lifting Equipment (WSH Council website)
� Checklist for Tower Crane Use (WSH Council website)
13 CDA_RIGGER
Annex A Course Syllabus
S/N Topic Sub-Topic Duration
1 Roles and
responsibilities of a Rigger
• Roles and responsibilities of a Rigger
• Attire for a Rigger
• Use of PPE
15 mins
2 Toolbox Meeting • Participate in a toolbox meeting as a Rigger 15 mins
3 Estimating load and Centre of
Gravity
• Safety Factor/Safe working load
• Estimating loads
• Centre of Gravity for regular and irregular loads
1 hr
4
Pre-lift inspection of
crane and lifting gear and
accessories
• Construction of wire ropes
• Types of slings (e.g. Chains, Wire Ropes and Fibre Ropes)
• Types of end fittings & connections
• Wire rope clips
• Inspection of wire rope slings
• Inspection of webbing slings
• Inspection of chain slings
• Practise good housekeeping of lifting gear and accessories
• Selection of correct sling & slinging method to different loads
• Rigging guidelines
• Precautions during rigging
1 hr
6 Rigging methods and techniques
• Preparation of timber wedges or slippers
• Apply rigging techniques to loads
• Conduct load safety checks to ensure load is safely rigged
• Cue the signalman
1.5 hrs
7 3-step lifting &
lowering method • 3-step hoist
• 3-step lower 30 mins
8
Accident prevention and
emergency response
� Hazards related to lifting operations � Dos and Don’ts of lifting operations � Common crane accidents case studies � Emergency procedures
1 hr
9 Out-door
Demonstration and Practice
• Estimate load and determine centre of gravity (for seven different types of loads)
• Practise rigging on five different loads
• Apply correct sling and sling method to regular and irregular loads
• Cue the signalman
• Apply 3-step lifting & lowering method
• Lift, lower, check and estimate clearance including blind spots
• Dismantle and restore rigging equipment
6 hrs
10 Assessment • Written (30mins)
• Practical (3hours)
30 mins 3 hrs
Total 16 hrs
14 CDA_RIGGER
Annex B Table of Specifications for Rigger Course
The table of specifications (TOS) shows what will be assessed and covered in the training course. It is a structured format based on the cognitive domain of Bloom’s taxonomy and provides a detailed listing of the course syllabus and course content that will meet the learning objectives in the course.
S/N Learning Objective Topic Sub-Topic
Cognitive Domain
Duration Knowledge & Comprehension
Application Analysis,
Synthesis & Evaluation
1
List the duties of the Rigger in lifting operation
Comply with safe work procedure for lifting
Roles and responsibilities
of a Rigger
• Roles and responsibilities of a Rigger
• Attire for a Rigger
• Use of PPE
15 mins - - 15 mins
2 Participate in toolbox meeting
Toolbox Meeting
• Participate in a toolbox meeting as a Rigger
- 15 mins - 15 mins
3 Estimate load and determine centre of gravity
Estimating load and Centre of Gravity
• Safety Factor/Safe working load
• Estimating loads
• Centre of Gravity for regular and irregular loads
30 mins 30 mins - 1 hr
4
Conduct pre-lift inspection of crane and lifting gear and accessories
Practise good housekeeping of lifting gear and accessories
Pre-lift inspection of
lifting gear and accessories
• Construction of wire ropes
• Types of slings (e.g. Chains, Wire Ropes and Fibre Ropes)
• Types of end fittings & connections
• Wire rope clips
• Inspection of wire rope slings
• Inspection of webbing slings
• Inspection of chain slings
• Practise good housekeeping of lifting gear and accessories
3.1 Assessment method and duration 3.2 Competency elements to be assessed
4 Assessment Instructions,guidelines and other requirements
4.1 Instructions for assessor 4.2 Guidelines for conduct of assessment 4.3 Requirements of assessor 4.4 Evidence sources for the conduct of assessment 4.5 Recording and reporting of assessment outcome
5 Assessment Record 6 Assessment Instruments – Samples of test papers and solutions
24 CDA_RIGGER
1 Purpose
The Rigger course is mandatory training for lifting operation course suitable for
individuals who are assigned to undertake the role of a Rigger in the construction and
other industries.
1.1 Legal Requirement
Factories (Operation of cranes) Regulations Reg 18 - An occupier shall appoint a
rigger for the purpose of rig up load for any lifting operation. To be appointed as a
rigger, he shall successfully completed a course approved by the commissioner of
WSH
2 Course Objective At the end of the course, trainees should be able to:
- List the duties of the Rigger in lifting operation
- Comply with safe work procedure for lifting
- Participate in toolbox meeting
- Estimate load and determine Centre of Gravity
- Conduct pre-lift inspection of lifting gear and accessories
- Practise good housekeeping of lifting gear and accessories
- Select the appropriate rigging equipment
- Rig and direct load to destination with safe lifting
- Check and verify load is properly rigged
- Describe legislative requirement for safe lifting operation
- List the duties and responsibilities of signalman for lifting operation
- List the personnel involved in lifting operation
- Identify hazards related to lifting operation
- Apply 3-steps lifting and lowering method
- Apply correct slinging method to ensure safe lifting operation
- Set up communication for safe lifting operation
- Explain the use correct lifting tackle
- Communicate using standard verbal and hand signal
- Response to accident and emergencies
25 CDA_RIGGER
2.1 Course Programme (Total Duration: 16 hours)
S/N Learning Objective Topic Sub-Topic
Cognitive Domain
Duration Knowledge & Comprehension
Application Analysis,
Synthesis & Evaluation
1
- List the duties of the Rigger in lifting operation
- Comply with safe work procedure for lifting
Roles and responsibilities
of a Rigger
� Roles and responsibilities of a Rigger
� Attire for a Rigger
� Use of PPE
15 mins - - 15 mins
2 Participate in toolbox meeting
Toolbox Meeting
� Participate in a toolbox meeting as a Rigger
- 15 mins - 15 mins
3 Estimate load and determine centre of gravity
Estimating load and Centre of Gravity
• Safety Factor/Safe working load
• Estimating loads
• Centre of Gravity for regular and irregular loads
30 mins 30 mins - 1 hr
4
- Conduct pre-lift inspection of lifting gear and accessories
- Practise good housekeeping of lifting gear and accessories
Pre-lift inspection of
lifting gear and accessories
• Construction of wire ropes
• Types of slings (e.g. Chains, Wire Ropes and Fibre Ropes)
• Types of end fittings & connections
• Wire rope clips
• Inspection of wire rope slings
• Inspection of webbing slings
• Inspection of chain slings
• Practise good housekeeping of lifting gear and accessories
• Selection of correct sling & slinging method to different loads
• Rigging guidelines
• Precautions during rigging
30 mins 30 mins - 1 hr
6 - Rig and direct load to Rig methods
and • Lifting plan and permit to work system 30 mins 1 hr - 1.5 hrs
26 CDA_RIGGER
S/N Learning Objective Topic Sub-Topic
Cognitive Domain
Duration Knowledge & Comprehension
Application Analysis,
Synthesis & Evaluation
destination for safe lifting
- Check and verify load is properly rigged
techniques • Preparation of timber wedges or slippers
• Apply rigging techniques to loads
• Conduct load safety checks to ensure load is safely rigged
• Cue the signalman
7 Apply 3-step lifting and lowering method
3-step lifting & lowering method
• 3-step hoist
• 3-step lower 30 mins - - 30 mins
8
- Identify hazards related to lifting
- Respond to lifting accident and emergencies
Accident prevention and
emergency response
� Hazards related to lifting operations � Dos and Don’ts of lifting operations � Common crane accidents � Emergency response procedures
1 hr - - 1 hr
9 NA Out-door
Demonstration and Practice
• Estimate load and determine centre of gravity (for seven different types of loads)
• Practise rigging on five different loads
• Apply correct sling and sling method to regular and irregular loads
• Cue the signalman
• Apply 3-step lifting & lowering method
• Lift, lower, check and estimate clearance including blind spots
• Dismantle and restore rigging equipment
- 5 hrs 1 hr 6 hrs
10 NA Assessment Written (30 mins) Practical (3 hours)
30 mins 3 hrs 3.5 hrs
TOTAL 16 hrs
27 CDA_RIGGER
2.2 Administrative Details Certification & Passing Criteria A Certificate of Successful Completion (CSC) will be awarded to a trainee who has completed the course and meets the necessary requirements:
• Attain at least 75% attendance during the training course • Undertake the on-going assessment and end of course examination • Achieve 60% mark in the written test and 100% Practical Performance
Course duration: 16 hours which includes 3.5 hours of assessment comprising
• Written Test (30mins)
• Practical (3 hours)
3 Assessment Plan 3.1 Assessment method and duration
S/N Assessment Instrument Duration
1
Practical Performance
This is a practical test where trainee is tested to select the appropriate the lifting gear, inspect lifting gear, estimate load, perform rigging, lifting and signaling for lifting operation
180 mins
2
Written Test
This is a theory test paper with 20 MCQs
30 mins
Total
210 mins
PP: Practical Performance WT: Written Test
28 CDA_RIGGER
3.2 Competency elements to be assessed
Learning Objective
Assessment Method
1 List the duties of personnel involved in lifting operation WT
2 Comply with safe work procedure for lifting WT/PP
3 Participate in toolbox meeting PP
4 Estimate load and determine centre of gravity WT/PP
5 Conduct pre-lift inspection of crane and lifting gear
and accessories
PP
6 Select the appropriate rigging equipment WT/PP
7 Rig and direct load to destination with safe lifting PP
8 Check and verify load is properly rigged PP
9 Apply 3-step lifting and lowering method WT/PP
10 Practise good housekeeping of lifting gear and accessories
PP
11 Identify hazards related to lifting WT/PP
12 Respond to lifting accident and emergencies WT
WT: Written Test PP: Practical Performance
29 CDA_RIGGER
4 Assessment Instructions, Guidelines and Other Requirements
4.1 Instruction for Assessor
For Written Test, Assessor should: a) Explain the test format and pass mark to the trainees b) Issue the test question papers to trainees on the day of test; c) Mark the test answer sheets after the test; d) Submit the duly marked test answer sheets to office for checking and signing; d) Record test results on appropriate results summary sheet; f) Proceed to conduct practical test where applicable, and submit the results summary sheet to office promptly.
For Practical Performance, Assessor should: a) Explain the test format, pass criteria and other practical instructions to the trainees b) Prepare the test materials; c) Conduct practical test on the scheduled date, time and venue; d) Record test results on appropriate results summary sheet; e) Submit the results summary sheet to office promptly.
4.2 Guidelines for conduct of assessment 4.2.1 Written Test These instructions concern the conduct of written test to assess the trainee’s competence which includes:
• The written test is one part of the assessment used to assess trainee’s understanding in underpinning knowledge and performance criteria of the course.
• Trainees are required to answer ALL the questions.
• Trainees may clarify with the invigilator if he does not understand the question being asked. However, the Invigilator reserved the right not to respond to your question if there is an attempt that the question being asked leads to the answer.
• The written test comprises 20 MCQs and the duration is 30 mins for completion.
30 CDA_RIGGER
Specification Item Details on Specification Learning Objective Topics listed in para 3.2 and extracted from the Table
of Specifications Duration 30 mins
Venue Lecture room Set Up 1. Lecture room setup for 16 trainees (max).
2. Table & chair for individual seating. 3. Projector & monitor. 4. Whiteboard & markers of different colours. 5. Whiteboard duster. 6. Blue or black pens. 7. A4 papers. 8. Test papers. 9. Answer sheet.
Conduct of the Written Test
1. Brief trainees to check whether all of them have the correct test paper with 20 MCQs. 2. Inform trainees on the time given for the test. 3. Remind them it is closed book test. Trainees cannot refer to any Workbook or discuss among themselves. 4. Trainees are allowed to ask the Assessor to explain the question for clarification, if any. 5. Trainees must achieve 60% of paper to be considered competent.
Recording the Assessment Result
1. Record findings and conclusions in the Assessment Record for Written Test under “Comments” column of the Assessment Record. 2. Record final marks attained.
Feedback 1. Inform and advise trainee on weaknesses and how to overcome such weaknesses. 2. Inform trainee on the final results of the assessment.
31 CDA_RIGGER
4.2.2 Practical Performance These instructions concern the Practical Performance of the trainee’s competence.
Specification Item Details on Specification Learning Objective Topics listed in para 3.2 and extracted from the Table
of Specifications Duration 180 mins Venue Field Set Up 1. Field set up set up for 16 trainees.
1. Brief trainees the procedure of test and observe safety 2. Inform trainees they will be assessed individually on
selection, inspection and rigging and signaling of load
3. Remind them they have to observe safety 4. Remind them they have to estimate weight of load 5. Trainees must achieve 100% to be considered competent.
Recording the Assessment Result
1. Observe every trainee. 2. Record observations and conclusions in the
Assessment Record 3. Record final marks attained.
Feedback 1. Inform and advise trainee on weaknesses and how to overcome such weaknesses. 2. Inform trainee on the final results of the assessment.
32 CDA_RIGGER
4.2.2.1 Instruction for trainees on Practical Performance
Rigging & Lifting Assessment Trainees would work in pairs with one being tested and the other assisting. They are assigned any two of the items in the following table. 1. They are required to:
a) Observe safety procedures at all times b) Perform inspection on surrounding vicinity and lifting
gear/accessories (See Appendix A - Inspection Checklist for Lifting Gear)
c) Estimate weight of loads and the Centre of Gravity d) Select the correct lifting gear c) Rig and lift the two items, one at a time, with guidance of the load
from load holding area to Location A and back to holding area (see attached Site Plan).
2. Trainees are to check Centre of Gravity and ensure that all loads are
properly slung and balanced before sending to location A. During hoisting and lowering, they are to observe the 3-step procedures for lifting or lowering.
3. Communicate effectively with the lifting operation personnel (eg lifting
supervisor, signalman) for lifting instruction, if any. 4. The pair of trainees would rotate roles to be tested.
Items From To Back To A) Skip B) Oil Drum C) BRC wire mesh D) L-shaped slab E) 6m pipe/pipe bundle F) Metal scaffold/scaffold
frame E) Sand bucket F) 6 m I beam
Load holding
area
Location A
Load holding
area
33 CDA_RIGGER
<ATP to insert Site Plan here>
Site Plan
34 CDA_RIGGER
Appendix A - Inspection Checklist for Lifting Gear
Inspected By (Name / Signature / Date)
Checked By _____________________________________ (Lifting Supervisor/Assessor) (Name / Signature / Date)
DESCRIPTION OF ITEMS YES NO
ACTIONS / REMARKS
SURROUNDING VICINITY AND PRE-LIFTING CHECK
1 Area of lifting being cordon off?
2 Permit to lift issue and posted
3 Risk assessment conducted and control measures briefed
4 Toolbox meeting conducted and Lifting plan briefed
WIRE ROPE/WEBBING
1 Are the SWL embossed indicated and Certificate of examination
2 Are they kinked?
3 Is the fibre exposed and broken wires found in the core?
4 Are they corroded?
5 Are they crushed or excessive surface wear?
6 Are there stretched wires?
7 Is there marked reduction in rope diameter?
CHAIN SLING
1 Are the SWL embossed indicated?
2 Are they dented, bent and twisted?
3 Are they gouged, chipped or cut?
4 Is there excessive wear at the bearing of the link?
5 Are they elongation at the welded joints of the link?
6 Are they elongated link?
7 Are they cracked and corroded?
SHACKLES
1 Are the SWL embossed indicated?
2 Are they worn off at crown or pin?
3 Are they enlarged at shackle’s opening?
4 Are the pins properly secured?
5 Are the pins bent?
6 Are they corroded?
HOOKS
1 Are the SWL embossed indicated?
2 Are there cracks detected?
3 Are they corroded?
4 Are they twisted?
5 Are they enlarged at the throat opening?
6 Are the Safety Latches functioning?
35 CDA_RIGGER
4.3 Requirements of Assessor
Assessments can only be carried out by approved assessors for this unit. The approved assessors must have the following qualifications: - WSQ Advanced Certificate in WSH or equivalent - Lifting Supervisor Safety Course Certification - At least 5 years relevant working experience as
supervisor/foreman/safety personnel in lifting operation - Advanced Certificate in Training and Assessment (ACTA) or equivalent 4.4 Evidence sources for the conduct of Assessment Assessment must be conducted strictly in accordance with the assessment plan. In particular, each trainee must complete all the assessment requirements in the time allocated. A judgment on the competency of the trainee must only be made based on the evidence gathered. The evidence for each of the assessment instrument is inspection checklist, written test and practical performance, observation during practical performance and assessment record. Note: For practical and practical performance assessments, ensure all safety procedures are complied. 4.5 Recording and reporting of assessment outcome All assessment outcomes must be accurately recorded in the assessment record form (see paragraph 5). Assessment outcome will be communicated to the trainee at the end of the assessment. The ATP shall maintain a record of the assessment outcome and related documents for each trainee for at least 2 years for audit by MOM.
36 CDA_RIGGER
5 Assessment Record
Following the assessed competency elements, the outcome is summarised in the assessment record as follows:
Rigger Course
Name of ATP:
Trainee Name: (As in NRIC/FIN)
NRIC/FIN: Date of Assessment:
Learning Objectives
Tick appropriate assessment tool(s)
Comments
PP
WT
1 List the duties of personnel involved in lifting operation
2 Comply with safe work procedure for lifting
3 Participate in toolbox meeting
4 Estimate load and determine centre of gravity
5 Conduct pre-lift inspection of crane and lifting gear and accessories
6 Select the appropriate rigging equipment
7 Rig and direct load to destination with safe lifting
8 Check and verify load is properly rigged
9 Apply 3-step lifting and lowering method
10 Practise good housekeeping of lifting gear and accessories
11 Identify hazards related to lifting operation
12 Respond to lifting accident and emergencies
WT: Written Test (Pass Criteria: 60%) PP: Practical Performance (Pass Criteria: 100%)
37 CDA_RIGGER
Overall assessment The trainee has been assessed as (tick appropriate box):
� Pass
� Fail
_______________________________ _______________________________ Trainee’s signature Assessor’s Signature Name:__________________________ Name:__________________________ Date:___________________________ Date:___________________________ Note to candidate: Candidates may appeal against the outcome of the assessment. By signing, the candidate is agreeing to accept the assessment outcome. Feedback on assessment outcome by Assessor / Feedback by trainee: