8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
1/22
Transmittal
Date: July 22, 2013
To: Steve Busen, LEED APSkanska
26100 American DriveSuite 200Southfield, Michigan 48034-2367
From: Shannon Shackelford
Project: Cardiovascular Institute and Harper-Hutzel Specialty CenterDetroit Medical Center,Detroit, Michigan
Project No: 2011-10001-000
Owner Project No:
Sent Via: Electronic E-Builder Site For your: Use/Records
Distribution: Jones Lange LaSalleAndrea Burg
JenkinsConstruction, Inc.James Robinson
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
2/22
SUBMITTAL LABEL
PROJECT NO: 2011-10001-000
PROJECT Cardiovascular Institute and Harper-HutzelSpecialty Center
Detroit Medical CenterDetroit, Michigan
DATE July 9, 2013
CONTRACTOR/SUPPLIER Jenkins/Skanska
DESCRIPTION Product Data/Shop Drawing
Cubicles - Curtain TrackJ/S Reference No. 0823
SPECIFICATION NO. 102123
COMMENTS
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
3/22
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
4/22
C/S Cubicle Curtains
SHOP DRAWING TRANSMITTAL
FOR APPROVAL ONLY - FABRICATION PENDING RELEASE
Date: 07 /03 / 2013
ATTN: JEFFREY M. STONE
RE: DMC CARDIOVASCULAR INSTITUTE
C/S ORDER NO: 998190
YOUR PO: SQ130006
Dear Customer,
Construction Specialties, Inc.
107 Johnson Blvd.Del Rio, TX 78840
Sales (908) 325-4900
Customer Service: (908) 849 4750Customer Service Fax: (908) 849-4399
www.c/sgroup.com
PONTIAC CEILING & PARTITION
715 AUBURN RD
PONTIAC, MI 48342
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
5/22
Re: SUBMITTALS
Please find the following items enclosed:
1 SHOP DRAWING COPIE
2 TRACK SAMPLES WITH ACCESSORIES:SATIN ANODIZED
2 IV TRACK SAMPLES:SATIN ANODIZED
If you should have any questions please contact me.
Thank you
Not included in this submittal.
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
6/22
Warranty
Construction Specialties, Inc.
107 Johnson Blvd.
Del Rio, TX 78840
Sales (908) 325-4900
Customer Service: (908) 849-4750Customer Service Fax: (908) 849-4399
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
7/22
Maintenance
Construction Specialties, Inc.
107 Johnson Blvd.
Del Rio, TX 78840
Sales (908) 325-4900
Customer Service: (908) 849-4750
Customer Service Fax: (908) 849-4399
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
8/22
* Drawing not to
scale
SMCCT #6062
The C/S Cubicle Curtain track is Dual Channel, extruded aluminum track
made from aluminum alloy in a anodized or white baked enamel. Trackdimensions are 1 3/8" x 3/4" deep (see below) with a minimum wall.
SURFACE MOUNTED
CUBICLE CURTAIN TRACK
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
9/22
Specification for Surface Mounted Cubicle Track
PART 2 PRODUCTS
2.01 ACCEPTABLE MANUFACTURERS
A. General: Cubicle Track system shall be complete as specified in this section and manufactured byCubicle Curtains, Cranford, NJ.
B. Substitutions: Other manufacturers are acceptable for evaluation only after compliance with Section
01630.
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
10/22
ConstructionSpecialt
107Johns
DelRio,T
Sales 908)3
CustomerService: 908)8
CustomerServiceFax: 908)8
INSTALLATION INSTRUCTIONS FOR CEILING-MOUNTED CUBICLE TRAC
C/S G E N E R A L C U B I C L E
Attached is a copy of our Tally Sheet, which lists all items required for individual rooms. The totals shown on this list shou
be used to check items received in shipment. Reports of shortages will not be accepted if made after (5) days after shi
ment has been received.
Large Bends (8'x8') will be furnished only where a project is large enough to offset the cost of crafting these bends. Whe
this is not permissible, Small Bends (2'x2') will be furnished with Splices and proper lengths of track - to be joined to th
Small Bends.
Measurements of Large Bends is approximately 8' 2 " x 8' 2 ". These will be shipped this way, to be cut on the job. F
proper installation, follow "Shop Drawing" for lay-out, if parts shipped were based on this.
1. Mark ceiling lightly where track is to be installed. Drill track at proper intervals. Start at the
center point of radius, and drill every 3' 0" on both directions. NOTE: Drill must be in perfect center
of track! When drilling ends of track, affix stops and gates and drill through these.
2. Prop track against ceiling with boards. Mark ceiling through drilled holes. Remove
track and drill through ceiling. (Size of drill to be determined by type of fastenersyou are using.) NOTE: If track is to be mounted against wood backings, then keep
tracking against ceiling, drill "guide hole" through ceiling, and then use proper
length of Wood Screws for a strong hold.
3. Head of fasteners should be pan-head - not to exceed Size No. 8
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
11/22
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
12/22
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
13/22
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
14/22
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
15/22
Specification for Surface Mounted IV Track
PART 2 PRODUCTS
2.01 ACCEPTABLE MANUFACTURERS
A. General: IV Track system shall be complete as specified in this section and manufactured by
Cubicle Curtains, Cranford, NJ.
B. Substitutions: Other manufacturers are acceptable for evaluation only after compliance with
Section 01630.
2.02 IV TRACK SYSTEM
A. I.V. Tracks: Cubicle Curtains I.V. track model #17000. Surface-mounted tracks of heavy
extruded aluminum alloy 6063-T5, 1 " x ", slotted to receive twist lock I.V. Carrier,
compete with accessories and components required for complete and secure installations
including splicers, end caps and corner bends.
1. Finish: Satin Anodized.
B C i C bi l C i 17500 T i L k I V C i C i h i h ll b
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
16/22
Surface Mounted I.V TackThe C/S General Cubicle I.V Track is dual channel, extruded aluminum track
Made from aluminum alloy in baked white enamel.
Aluminum I.V Carrier Stop # 162(W)
17500 TWIST LOCK
I.V. CARRIER
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
17/22
49 Meeker Avenue
Cranford, NJ 0701Tel: (908) 849-474Fax: (908) 849-439
MODEL# 17150
Fabricated of polished stainless steel this unit has a " diameter
tubing for the main shaft, 3/8" diameter for the inner shaft, and four
folding " diameter spiral safety arms plus one additional hook in the
bottom as the fifth holder.
DELUXE 5 BOTTLE I.V. PENDANT
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
18/22
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
19/22
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
20/22
Confirm assignedscope. Only curtains
are not construction
scope responsibility.
Yes
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
21/22
8/10/2019 Cubicle Curtain Track Shop Drawing for Reference
22/22
41030A
P/R 1 ISO