CS10 & CS11 SerieS ClutCh Shift pto...CS10 & CS11 SerieS ClutCh Shift pto parts list and service manual Muncie Power Products, Inc. for the allison world transmission U.S. Pat. 5,542,306

CS10 & CS11 SerieS

ClutCh Shift ptoparts list and service manual

Muncie Power Products, Inc.

for the allison world transmission

U.S. Pat. 5,542,306

� MunciePowerProducts,inc.

CS10 & CS11 SerieS ClutCh Shift pto

ExplodEd ViEw

partS liSt and deSCription

IteM qty Part nuMber descrIPtIon 1 1 03T36214 InputGear(05)(50T/27T) (See Table A for additional gears)

2 2 10T35776 InputBearing

2a 1 18T38748 ConeSpacer(0.743/0.741) (See Table B for additional spacers)

3 1 18T35783 BearingShim (See Table C for additional shims)

4 4 19T39418 Capscrew“C”,“D”,“2” 5 1 15T36206 BearingCover,Closed(CS10) 15T37970 Bear.Cov.w/oValveProv.(CS11) 6 1 12T36081 O-Ring 7 1 12T36207 O-Ring 8 1 10T35994 Bearing 9 2 26T36175 RollPin(CS10) 10 1 21T36170 DragBrakePlate(CS10) 11 1 21T36172 BronzeBrakeDisc(CS10) 12 1 21T36171 DragBrakeRotor(CS10) 13 3 24T36040 SnapRing 14 2 10T35989 ThrustRace 15 1 10T35991 Bearing 16 1 02T36219 BellGear(05)(47T) 02T36220 BellGear(06)(45T) 02T36221 BellGear(07)(43T) 02T36222 BellGear(08)(40T) 02T36223 BellGear(10)(38T) 17 1 02T36113 ClutchHub(Before4/99) 1 49TA4136 ClutchHubAssembly(4/99) (Includes:17a,17b,17c)(SeePg8) 17a 1 49T37920 ClutchHub(4/99) 17b 1 49T37921 ClutchFlange(4/99) 17c 1 24T37951 SnapRing(4/99) 17d 1 10T37930 ThrustWasher(4/99) (Usedw/49TA4136Only) 18 7 49T33564 FrictionDisc 19 11 49T40641 SpacerDisc(Before4/99) 6 49T40641 SpacerDisc(4/99) 20 1 27T36112 Spring 21 1 49T36114 Piston 22 1 12T36054 O-Ring 23 2 12T36053 O-Ring 24 1 49T36115 PistonCup 25 2 12T35774 O-Ring 26 1 19T35785 SetScrew 27 1 07T35780 IdlerShaft 28 1 01T36204 Housing(1Arrangement) 01T36202 Housing(3Arrangement)

29 1 06T37932 OS“B”replaces06T36039 06T37933 OS“C”,“2”,“X”replaces06T36072 06T37934 OS“D”,“S”replaces06T36073 06T37935 OS“E”,“Y”,“Z”replaces06T36074 06T37936 OS“I”replaces06T36832 06T37937 OS“P”replaces06T36799 30 1 10T35775 OutputBearing 31 1 26T01627 WoodruffKey 32 1 12T35773 ORing 33 1 11T37795 Seal 34 1 15T39226 BearingCov.,Open(“2”,“B”,“C”,“X”) 14T35767 HydFlange(“D”,“P”,”Z”)

IteM qty Part nuMber descrIPtIon34continued 14T40576 HydFlange(“E”Only) 14T36007 HydFlange(“Y”Only) 14T36834 HydFlange(“I”Only) 14T37474 HydFlange(“S”Only) 35 6 19T39417 Capscrew(“B”,“C”,”X”,“2”) 36 1 14T31499 CompanionFlange(“C”Only) 14T37498 CompanionFlange(“2”Only) 37 1 21T20092 Washer(“C”,“2”Only) 38 1 21T20526 LockWasher(“C”,“2”Only,IfReq.) 39 1 19T20522 Capscrew(“C”Only)(CS11) 1 19T38266 Capscrew(“X”,“2”Only)(CS11) 40 6 19T39257 SocketCapscrew“D”,“P”,“S”,“Z”Hyd 19T35386 SocketCapscrew“I”Hyd 19T31577 SocketCapscrew“E”,“Y”Hyd(CS10/11) 41 1 25T35724 CapPlug“D”,“S”(StorageOnly) 25T35936 CapPlug“E”,“I”,“Y”,“Z”(StorageOnly) 25T35725 CapPlug“P”(StorageOnly) 42 1 35T36092 Solenoid(12Volt) 35T36447A Solenoid(24Volt) 43 4 25T21684 PipePlug 44 2 19T36174 SetScrew 45 2 27T36173 Spring 46 1 13T35777 Gasket 47 1 25T35999 Plug 48 1 25T35784 Orifice 49 1 43T35867 Elbow 50 1 45T35865 Hose 51 1 43T36231 Tee 52 1 49T36283 HoseClamp 53 1 21T36448 Washer 43tK3881 standard Hose Kit 43tK3885 Hd For r.s. Installation 54 1 45T36274 Hose(Std28”) 45T36273 Hose(HDR.S.57”) 55 1 43M68014 Elbow 56 1 43T36445 Elbow(useasneeded) 20MK1001 Mounting bolt Kit (Incl. 57, 58) 57 2 20T35779 AlignmentStud 58 8 19T35778 12Pt.Capscrew(30mm) 59 1 49T36493 Protector 60 1 35T37928 RemoteMountValveAss’y(CS11) (SeePage6) 61 1 25T34029 Caplug 62 2 25T34029 Caplug(CS11) N.S. 1 48tK4037 Installation Kit (12v)Incl:ShiftKit, GasketPack,StudKit,Std.HoseKit 48tK4039 Installation Kit (24v)Incl:ShiftKit, GasketPack,StudKit,Std.HoseKit N.S. 1 cs10-GsK Gasket KitIncl:(1)6,(1)7,(1)22, (2)23,(2)25,(1)32,(1)33,(1)46 N.S. 1 cs10-rbK rebuild KitIncl:(2)2,(1)3,(1)6, (1)7,(1)8,(2)9,(1)11,(3)13,(2)14, (1)15,(7)18,(11)19,(1)22,(2)23, (2)25,(1)30,(1)32,(1)33,(2)45,(1)46 N.S. 1 48tK4051 cs11 conversion KitIncludes: 43TK4036HoseKit(page6), 35T37928ControlValve12VDC, 15TA4056CoverKit,andSolenoid MountingHardware. N.S. 1 25T37702 Caplug

*DateCodeIsLocatedUnderPTOModelLabel.

Output Shafts (OS) were changed 4/99 to accommodate the two-piece clutch hub (17). When replacing shaft in PTO prior to 4/99, clutch hub

assembly (17) and washer (17d) must be added to required parts.

MunciePowerProducts,inc.�


tableS a, b, Ctable aInPut Gear asseMbLy — IteM 1 (Soldonlyasassembly)

Input sub designation based on ratio teethassembly Input Gear03TA4619 A1005 03T36214 05 50T/27T03TA4620 A1006 03T36215 06 50T/29T03TA4621 A1007 03T36216 07 50T/31T03TA4622 A1008 03T36217 08 50T/34T03TA4623 A1010 03T36218 10 50T/36T

table bcone spacer – IteM 2a

Part no. tHIcKness18T38748 0.743/0.74118T38532 0.740/0.73818T38533 0.737/0.73518T38534 0.734/0.73218T38535 0.731/0.72918T38536 0.728/0.72618T38537 0.725/0.72318T38538 0.722/0.72018T38539 0.719/0.71718T38540 0.716/0.71418T38590 0.713/0.71118T38591 0.710/0.70818T38592 0.707/0.704

table Cbearing shim – IteM 3

Part no. tHIcKness18T37153 0.1500/0.148018T38731 0.1475/0.145518T37152 0.1450/0.143018T38730 0.1425/0.140518T37151 0.1400/0.138018T38729 0.1375/0.135518T36229 0.1350/0.133018T38728 0.1325/0.130518T36230 0.1300/0.128018T38727 0.1275/0.125518T38726 0.1225/0.120518T35781 0.1250/0.1230

CS10 SerieS ConVerSion to reMote aCtiVation Solenoid

10

8A

-4JIC

7

71

5

4

3

6

5

4

RED

BLACKIN

PS

CL

BlueGreen

11

Exhaust Line

2

9

7

CoNVERSioN KiT 48TK4942

PlugPlug

ExhaustLine

Pressureoneport,plugotherport

TransmissionMainPressConnection

1512

1413

BlockValvemustbespacedoffanyflatsurfaceusingwashers(15)topre-ventdamagetosolenoid.

IteM qty Part no. descrIPtIon

1** 1 30T36727 PressureSwitch 2** 1 34T35872 WireHarness 3 1 43T37503 1/8”NPT/JICFitting 4 2 43T35867 1/8”NPT/JICElbow 5 4 45T36274 HoseAssembly 6 1 43T36231 StraightBranchTee 7 3 43M68014 7/16-20Str.Elbow 8 1 35T37928 Valve12VD.C. 9 1 25T40727 CavityPlug 10 2 25T36726 Str.Plug 11 1 25T21684 PipePlug

SOLENOID MOUNTING HARDWARE

12 2 19T36623 Capscrew 13 2 22T35140 Nut 14 2 21T37991 Lockwasher 15 2 21T23153 Washer

conVersIon KIt - 48tK4942

** Included with original PTO, not included in this kit.

inStallation kitS

Harness

19

Transmission Main Press Connection

18

A

-4JIC

17

17

17

5

1514

13

16

15

14

RED

BLACKIN

PS

CL

BlueGreen

CAUTION:INSTALL EXHAUST FITTING INTO PIPE THREAD PORT IN END COVER. USE PIPE THREAD SEALANT ONLY, DO NOT USE TAPE.

OVER-TIGHTENING THIS FITTING INTO PORT MAY CAUSE BLOCKAGE AND SOLENOID WILL NOT RELEASE PTO CLUTCH PACK.

34T35872 Old Style

10

cs10 InstaLLatIon KIt - 48tK3882 (12V)IteM qty Part no. descrIPtIon 30t36270 switch ass’y (includes 1,2,3,4) 1 1 36MA1005 SwitchBracket 2 1 36T36271 FacePlatewithoutlightaccess 3 1 30T35687 RockerSwitch(12v) 4 1 33T36299 FuseAssembly 5 1 30T37954 PressureSwitch 6 1 34M18250 FemaleSpadeConnector 7 1 34M18009 RingTerminal 8 2 34M18187 FemaleSpadeConnector 9 1 34M18002 ButtSplice 10 1 34T40902 WireHarness 11 6 37M18000 Wire 12 1 37T35674 GrommetN.S. 1 36MK1007 BoltKitIncl.w/30T36270&30T36453N.S. 1 43M05522 Elbow

30t36453 switch ass’y (includes 1 & 2 above and 3 below. 3 1 30T35712 RockerSwitch(24V)

For 24v option Kit no. 48tK3891 (substitute)

cs10 InstaLLatIon KItwith dIrect actIVatIon soLenoId

(no Hose Kit required)

cs11 InstaLLatIon KItwith reMote actIVatIon soLenoId

++

A

****

111710

White

8

36

94

Black

BlueRed

Black

GREEN

DC12V

YELLOW

Neg. Ground

12

Green

Red

* Battery Ground

SPD-1001A

++ RED light in rocker switchis to turn "ON" when PTO isengaged and to turn "OFF" when PTO is disengaged.

PG-5

*

*

*

CTOTach Output

Faceplate (36M1006) and 12V light assembly (32MSRRV) are available in their own separate kit (36TK4971).Sold Separately

++A

1211

49

6

3

21

10

++

BlueBlack

Green

DC12v

Neg. Ground

Red

* Battery Ground

RED light in rocker switch

PTO is disengaged.engaged and to turn "OFF" whenis to turn "ON" when PTO is

*

cIrcuIt InstaLLatIonWhen used without overspeed switch

cIrcuIt InstaLLatIonWhen used with overspeed switch

cs11 conVersIon KIt - 48tK4051 (12V)use with 48tK3882 (n.s.)

IteM qty Part no. descrIPtIon 13 1 43T37503 1/8”NPT/JICFitting 14 2 43T35867 1/8”NPT/JICElbow 15 4 45T36274 HoseAssembly 16 1 43T36231 StraightBranchTee 17 3 43M68014 7/16–20Str.ThreadElbow 18 1 35T37928 Valve12VD.C. 19 1 15TA4056 CoverAssembly(IncludesBearing& o-ring(6&7)asshownonpage2.N.S. 2 19T36623 CapscrewN.S. 2 22T35140 NutN.S. 2 21T37991 Lockwasher

18 1 35T37967 Valve24VD.C.

For 24v option Kit no. 48tK4052 (use with 48tK3891) substitute:


aCCeSSory kitS

installation hose kit

3

2 1


1 1 45T36274 HoseAssembly-Std.28” 45T36273 HoseAssembly-HDTop57” 45T39186 HoseAssembly-Special17” 2 1 43M68014 Elbow(Transmission) 3 1 43T36445 Elbow(useasneeded) (43TK3881&43TK4545only)

43tK3881 — Hose KIt - standard 28”43tK3885 — Hose KIt - For toP r.s. Hd serIes 57”43tK4545 — Hose KIt - sPecIaL 17”


1 4 45T36274 HoseAssembly-Std.28” 2 3 43M68014 Elbow(Transmission) 3 1 43T36445 Elbow(useasneeded)N.S. 2 43T35867 ElbowN.S. 1 43T36231 TeeFitting

43tK4036 — Hose KIt For cs11 serIes

Bolt kit

qty Part no. descrIPtIon

6 19T40266 12pt.Capscrew-30mm 2 19T37727 12pt.Capscrew-25mm 2 20T35779 AlignmentStud 6 21T40360 NordlockWasher

20MK1001 — boLt KIt For cs10

Mount two halves of washerwith insides facing.

12

3

4

5

67

8

Outside Inside25 mm 30mm w/LW

NordlockWasher


12

3

4

5

67

8


NordlockWasher

Mounttwohalvesofwasherwithinsidesfacing.

the cs10 includes the mount-ing kit, special shim/gasket, high pressure hose hookup kit, wiring harness, dash bracket kit, and installation instructions. the Pto is available with a pulse gener-ator (pick-up) for use with the Muncie digital tachometer - 38MK2000 (request MP92-04) or use with the Muncie digital switch sPd-1001a to control the engagement or overspeed protection of the Pto. con-tact your Muncie application specialist for assistance with these options.

important


12

3

4

5

67

8


NordlockWasher

Thetwo(2)25mmlongcapscrewsaretobeusedinposi-tions1and3asshownindiagram(Fig.1).Thesix(6)30mmlongcapscrewsandsix(6)speciallockwashersareusedinpositions2,4,5,6,7,&8.


12

3

4

5

67

8


NordlockWasher

Figure 1. - caPscreW PLaceMent

torque to 45 lb.Ft.

3

4

1

2

4A

B

35T37967 24V VALVE W/BLOCK (INCL. 35T36447A)35T37928 12V VALVE W/BLOCK (INCL. 35T36092)BLOCK TYPE VALVE FOR CS11/CS21

REPLACEMENT PARTS - BEFORE 2008

CLPS

4 - 5 ft.lb.

20 ft.lb.

5

solenoid ValVe

3

24

5

1


1 1 31T35108 MagPickup 2 1 21T35109 JamNut 3 1 34MA1415 WiringHarness 4 1 21T36099 FlatWasher 5 1 12T35774 O-ring

31tK3873 — sPecIaL oPtIon “u”

speed sensor kit35t37928 (12V) - w/ 35T36092 Solenoid35t37967 (24V) - w/ 35T36447 Solenoid

IteM qty Part no. descrIPtIon 1 8 22T39429 Nut 2 1 37T39088 12vCoil(Delta) 35T38997 24vCoil(Delta) 3 1 35T37997 Valve 4 2 12T39408 O-ring5* 1 N.A. ManifoldBlk(CS11)

*(NotSoldSeparately)

�MunciePowerProducts,inc.

CS10 & CS11 diSaSSeMbly and reaSSeMbly

DRAG BRAKEADJUSTMENTSET SCREWDRAG BRAKE

ADJUSTMENTSET SCREW

(Reference Exploded View on page 2)

7

86

5 8

10 11

12

16 29

13

1/4-20UNC

draG braKe and beLL Gear reMoVaLdenotes sPecIaL serVIce Procedures

18 19

1716

taPer roLLer bearInGs

dIsasseMbLy Procedure 1.RemovetheCS10inputgear,byremovingthesetscrewinthepadanddrivingthe

idlershaftfromthehousing.(26,27) 2.Removethesetscrews(44)fromthebearingcover(5)whichholdthedragbrake

springs(45).Positionthehousingsothatthespringsfallfromhousing. 3.Removethefourlargesocketcapscrews(4)whichholdthebackcovertothePTO

housing. 4.Positionthehousingagainstabenchblockandhittheendoftheoutputshaftwitha

softfacehammertoremovetheentireoutputshaftassemblywithbearingcover(5). 5.Removethetwopipeplugs(43)fromthebearingcover.Thisexposestheballbear-

ingassemblywithinthecover. 6.Usinga1/4”punchandalternatingbetweenthetwoholes,drivethebearingandshaft assemblyfromthebearingcover. 7.Usingabearingpullerremovetherearbearing(8)bygrabbingthedragbrakeplate

(10)andremovingbothpieces.Thebronzebrakedisk(11)canberemoved. 8.Insertfour1/4-20capscrewsintothedragbrakerotor(12)untiltheyjusttouch

thebackofthebellgear.Usingan“X”patternscrewthecapscrewsinat1/4turnintervalsuntilthebrakerotorisfreeoftheoutputshaft(29).

9.Thepistonandclutchpackmaybeservicedwithoutremovalofthedragbrake.Usingsnapringpliers,removethesnapring(13)locatedontheoutputshaftendwhilegentlypushingonthepistoncup(24).

10.Pullthepistoncup(24)fromtheshaftandthepiston(21)willgowithit.11.Tapthepistoncuponawoodsurfacetoremovethepiston.12.Removethespring(20).Theclutchfrictiondiscs(18)andspacerdiscs(19)and

innerclutchhub(17)canberemovedbypointingtheshaftenddown.13.Withthedragbrakeremoved,thesnaprings(13)onthisendofthebellgearcan

be removedwithsnapringpliers.Thisallowsthebellgeartoberemovedtowardsthe

closedend.Theinternalbearing(15)ofthebellgearcaneasilyberemoved.

reasseMbLy Procedure14.Thereassemblyoftheunitismadeinreverseofthedisassembly.There-useof

seals,o-ringsandsnapringsarenotrecommended.15.Besuretolubricatetheo-ringsandallbearingsuponinstallation.Itisimportantto

positiondragbrakeplatesothatinputgearclears.Thisisthereasonfortheflatsides oftheplate.Torquecapscrewstothevaluesshownortothefollowingvalues. 5/16capscrews-18ft.lb.3/8capscrews-36ft.lb.1/4setscrew-9ft.lb.16TheInputGearisreplacedasasetwhichincludesthegear,conespacer,&bearings. see table a.Slidethissub-assemblyintothehousingtolineuptheidlershaft.17Taptheidlershaftintothehousingandthroughbothbearingraces.

18Taptheidlershaftinthereversedirectionsothatitisflushwiththebearinginthisassembly.Insertthethickestshimthatcanbeinstalledbyhandinthegapbetweenthebearingandhous-ing.Removeshimandselectthenextthickershimanddriveitintothegap.Rotatingthegeartomakesureiteasilyrotates.Therecommendedbearingpre-loadis.002”to.006”loose.(Theconespacersetsthisper-loadandmeasurementisnotrequired.)

19Taptheidlershaftintopositionandinstallsetscrew.

soLenoId VaLVe InstaLLatIon (cs10 onLy)20Separatethecoilfromthevalveassembly.Insertthevalvecartridgeintotherearcover andtorqueto20ft.lb.21Sliponeo-ringandthecoiloverthevalve.Slipthesecondo-ringon.22Placethreadlockingcompoundonthepostthreadsandinstallnut.Torquethenut 4to5ft.lb.max.23Placethreadsealantonpipeplugs.Torque10-16ft.lb.

draG braKe adjustMent (cs10 onLy)24.Wheninstallingtherearcoverbesuretoaligntherollpinsinthedragbrakeplatewith

theholesintherearcover.NOTE:Itisimportantthatoneoftheflatedgesofthisplate ispositionedtowardstheinputgear.25.Afterthecoverhasbeenattachedtothehousinginsertthespringsintothe

holes.26.Insertthesetscrewoverthespringandturnthescrewfour(4)fullturns.27.FollowthetestandadjustmentproceduresintheCS10ownersmanual.

42c

42b

42a

2323

20

22

4343

5

droP-In soLenoId

�MunciePowerProducts,inc.

Model nuMber ConStruCtion

Pto tyPe ClutchShiftCS

MountInG 10-BoltMount–10 10-BoltMountwithRemoteSolenoid–11

trans. cs Gear data Allison10.16PRH-A10

sPeed ratIo 05-.57:1 06-.64:1 07-.72:1 08-.85:1 10-.95:1

sPecIaL Features X-None(PressureLubeisstandardonallunits) B-Hosekit(HDTrans.R.S.) D-PulseGenerator&SPD-1001A U-PulseGenerator 3-17”ActivationHose 4-LessActivationHose(CS10)

outPut tyPe B-1-1/4Round5/16KW C-1-1/420Spl.(1410CompanionFlange) D-SAE“B”2&4Bolt E-SAE“C”2&4Bolt I-DIN5462 P-SAE“B&B”2&4Bolt S-SAE“B”2Bolt Y-SAE“C”2Bolt 2-DINCompanionFlange

asseMbLy arranGeMent 1or3

sHIFter tyPe H-12VoltElectric/Hydraulic J-24VoltElectric/Hydraulic

cs10A1005H1BX

CS10 ClutCh hub replaCeMentEffectiveApril1999theclutchhubsuppliedintheCS10SeriesPTOhasthetwopiececlutchhubasshownonthispage.Thetwopiecehubconsistsofasplinedhubandaflangewhichisheldtogetherbyasnapring.Becauseofthisdesignchangetheclutchpackstackuphaschangedasshownonpage2.

BeginbyassemblingthenewClutchHub: 1. Placetheflange(17b)ontotheClutchHub(17a)sothattherecessedarea oftheflangeisagainstthesplines.Fig.1. 2. UsingsnapringpliersinstalltheSnapRing(17c)ontotheClutchHub(17a). 3. TheNewClutchHubrequiresanew outputshaft.Selecttheappropriate shaftandinstalltheThrustWasher (17d)againstthesplinesontheout putshaft(29).Fig.2. 4. Holdthrustwasherinplacewiththe SnapRing(13).

CurrentInventorythathasbeenreworkedwillhavean“X”markedontheshaftbythepartnumber.

06T37932=06T36039X(“B”)06T37934=06T36073X(“S”,“D”)06T37636=06T36832X(“I”)

06T37933=06T36072X(“C”,“X”,“2”)06T37935=06T36074X(“E”,“Y”)06T37937=06T36799X(“P”)

Pto asseMbLy arranGeMents

NO. 1 ASSEMBLy NO. 3 ASSEMBLy


diMenSionS IN INCHES (MM)

sae “c” 2-boLt 1-1/4” 14 sPLIne (“y” oPtIon) 1-1/2” 10 sPLIne W/dIn 100 FLanGe (“2” oPtIon)

sae “b&b” 2&4 boLt 1” 15 sPLIne (“P” oPtIon) sae “b” 2 boLt 7/8” 13 sPLIne (“s” oPtIon)

dIn 5462 36MM 8 sPLIne (“I” oPtIon)sae “c” 2&4 boLt 1-1/4” 14 sPLIne (“e” oPtIon)

1-1/2” 10 sPLIne W/1410 serIes FLanGe (“c” oPtIon) sae “b” 2&4 boLt 7/8” 13 sPLIne (“d” oPtIon)std 1-1/4” round Keyed sHaFt (“b” oPtIon)

CS10 CS11


SP95-03 (Rev. 10-09) Printed in the U.S.A.© Muncie Power Products, Inc. 2009

Muncie Power Products, Inc. Member of the Interpump Hydraulics GroupGeneralOfficesandDistributionCenter•P.O.Box548•Muncie,IN47308-0548

(765)284-7721•FAX(765)284-6991•E-mail [email protected] site http://www.munciepower.com

DriveProducts,ExclusiveAgentsforCanada,ISO Certified by an Accredited Registrar

CS10 & CS11 SerieS ClutCh Shift pto...CS10 & CS11 SerieS ClutCh Shift pto parts list and service manual Muncie Power Products, Inc. for the allison world transmission U.S. Pat. 5,542,306

Documents