CP series INCLINED LIQUID COLUMN MANOMETERS · For a pressure measurement ... HP series INCLINED LIQUID COLUMN MANOMETERS The HP range of inclined liquid column manometers, developed

CP seriesINCLINED LIQUID

COLUMN MANOMETERS

The CP 25 inclined liquid column manometer, developed and manufactured by KIMO measures slight variations in pressure, depression or differential pressure of air or gas.It is specially designed for checking clogging of filters in painting booths.

● Graduation scale via coloured zones for fast and easy reading● Safety reservoir enabling momentaneous overshooting of the scale● Supplied with two 487 connectors and a bottle of AWS 10 liquid

KEY POINTS

0 – 25 mm CE

5 mm

MEASURING RANGE

SNESITIVITY SCALEfor 1 mm CE

DIMENSIONS

Pressure / Depression

76 mm

152 mm

85 mm

15 mm

Ø 5 mm

Cylindrical 1/8 gas connectorØ 6.2 mm ribbing

[email protected] GmbH

TECHNICAL FEATURES

Recommended range of usePossible range of useMaximum static pressureManometer bodyLiquid columnGraduation

Positioning

Manometric liquidReservoir capacityConnection

Wall-mounted

From +5 to +30°CFrom -30 to +60°C6 barsTransparent 15 mm thick Altuglas.Entirely bored in the solid block, Ø 4 mm.Directly silk-screened onto the rear face with different colour zones :

from 0 to 5 mm CE : whitefrom 5 to 10 mm CE : greenfrom 10 to 15 mm CE : yellowfrom 15 to 25 mm CE : red (Variations possible on request).

Horizontal positioning via integrated spirit level and milled, nickel-plated brass adjusting screw, vertical travel 12 mmAWS 10 red oil - density 0.87 at 15°C.20 mlØ 5x8 mm semi-rigid crystal tube, on Ø 6.2 mm ribbed, nickel-plated brass connectors, 1/8 gas thread.With or without white PVC support

MOUNTING

1. Mount on a wall or a vertical partition wall with two maximum Ø 5 x 25 mm screws (supplied).2. Set horizontality using the integrated level and the milled adjusting screw.3. Unscrew the connector on the reservoir and slowly pour the manometric liquid to zero point on the graduation.4. Remount the connector without overtightening.5. Connect the manometer with the Ø 5 X 8 mm crystal tube to the pressure or depression source to be checked.

NOTES : For a pressure measurement..............................Connect the crystal tube to the right-hand connector (+)For a depression measurement..........................Connect the crystal tube to the left-hand connector (-)For a differential pressure..................................Connect the highest pressure to the right-hand connector (+) and the lowest pressure to the left

hand connector (-)

MAINTENANCE :

The CP 25 manometer requires no special maintenance other than simply changing the reading liquid once a year.

Ref. F

Tang

– CP

25 –

01/99

A - R

CS 24

(24)

Pér

igueu

x 349

282 0

95 N

on-co

ntrac

tual d

ocum

ent –

We r

eser

ve th

e righ

t to m

odify

the c

hara

cteris

tics o

f our

pro

ducts

with

out p

rior n

otice

.


MERCURY

VF1 LIQUID

Reference

Reference

GF 500GF 1000

GF 68GF 134

Measuring rangemm CE mbar

mm HG mbar

250 – 0 – 250500 – 0 – 500

25 – 0 – 2550 – 0 – 50

250 – 0 – 250500 – 0 – 500

340 – 0 – 340670 – 0 – 670

mm CE

mm HG mbar

mbarResolution

1 0,5

5

VERTICAL LIQUIDCOLUMN MANOMETERS

GF series

The GF range of vertical liquid column manometers, developed and manufactured by KIMO, are mainly for checking pressures in gas networks within measurement ranges which vary according to the type of manometric liquid used : VF 1 or MERCURY.(See table below)

● ''U''-shaped column for measuring consecutively positive and negative pressures● Measurement by addition of values read on each column● For fixed and portable use● Zero adjustment by moving the slide strip● Possibility of resisting static pressures over 10 bars● Altuglas column sunk into the solid block● Comes with bottle of liquid, 2 screws and rawplugs

MEASURING RANGE

KEY POINTS

Pression / Dépression

1

Measuring range Resolution


Recommended range of usePossible range of useMaximum static pressureManometer bodyLiquid column

Graduated slide stripZero adjustment

Manometric liquidConnection

Wall mounting

From +5 to +30°CFrom -30 to +60°C14 bars20 mm thick PVCTube Ø 4 X 10 mm in altuglas for mercuryTube Ø 6 X 10 mm for VF1Transparent altiglas. Cross-section 54 X 3 mmBy moving the graduated slide strip, travel 20 mm.Fixed via milled, nickel-plated brass screwVF1 liquid, density 13,545 or mercury, density 1Ø 5x8 mm semi-rigid crystal tube on Ø 6.2 Delrin ribbed connectors with M 7x100 thread.

2 screws Ø 5 X 25 mm

Ref.

abc

Distance between tubes

Weight

1. Mount the manometer on a wall or partition wall with two maximum Ø 5 x 25 mm screws.2. Unscrew the left-hand connector and slowly pour the manometric liquid to zero point on the graduation3. Remount the connector without overtightening.4. Connect the manometer with the Ø 5x8 mm crystal tube to the pressure or depression source to be checked.

Note :

For a pressure measurement.............................. Connect the crystal tube to one of the two connectorsFor a depression measurement.......................... Connect the crystal tube to one of the two connectors.

TECHNICAL FEATURES

GF 500 GF 1000 GF 68 GF 134

607 mm70 mm25 mm

571 mm540 g

1107 mm70 mm25 mm

1071 mm980 g

607 mm70 mm25 mm

571 mm800 g

1107 mm70 mm25 mm

1071 mm1450 g

DIMENSIONS

MOUNTING

Ref. F

Tang

– GF

– 15

/11/1

2 - R

CS 24

(24)

Pér

igueu

x 349

282

095

Non-

contr

actua

l doc

umen

t – W

e re

serve

the r

ight to

mod

ify th

e cha

racte

ristic

s of o

ur pr

oduc

ts wi

thout

prior

notic

e.

bc

a


HP seriesINCLINED LIQUID

COLUMN MANOMETERS

The HP range of inclined liquid column manometers, developed and manufactured by KIMO, measure slight variations in pressure, depression or differential pressure of air or gas.They are particularly recommended for measuring overpressures in clean rooms, operating blocks, laboratories, aseptic rooms, laminar flows....

● High measurement sensitivity● Very low pressure ranges● Zero adjustment by moving the slide strip.● Integrated spirit level for adjusting horizontality.● Supplied with a white PVC support, 2 screws and 2 rawlplugs, two 487 connectorsand a bottle of AWS 10 liquid.

KEY POINTS

MEASURING RANGE

Resolution

0,1 mm CE or 1 Pa0,1 mm CE or 1 Pa

Sensitivity scalefor 1 mm CE or 10 PA

20 mm15 mm0 – 100

0 – 50Pascal

0 – 50 – 10

mm CEMeasuring range

Reference

HP 5HP 10

0,1 mm CE or 1 Pa10 mm0 – 1500 – 15HP 15



TECHNICAL FEATURES

Recommended range of usePossible range of useMaximum static pressureManometer bodyLiquid columnGraduated slide strip

Positioning


Wall-mounted

From +5 to +30°CFrom -30 to +60°C6 barsTransparent 20 mm thick Altuglas.Entirely bored in the solid block, Ø 4 mm.Transparent Altuglas. Cross-section 20 x 2 mm.

Horizontal positioning via integrated spirit level and milled, nickel-plated brass adjusting screw, vertical travel 12 mm.AWS 10 red oil, density 0.87 at 15°C.20 mlØ 5x8 mm semi-rigid crystal tube, on Ø 6.2 mm ribbed, nickel-plated brass connectors, 1/8 gas thread.With or without white PVC support.

MOUNTING

1. Mount on a wall or a vertical partition wall with two maximum Ø 5 x 25 mm screws (supplied).2. Set horizontality using the integrated level and the milled adjusting screw.3. Unscrew the connector on the reservoir and slowly pour the manometric liquid to zero point on the graduation.4. Remount the connector without overtightening.5. onnect the manometer with the Ø 5 X 8 mm crystal tube to the pressure or depression source to be checked.

NOTES : For a pressure measurement..............................Connect the crystal tube to the right-hand connector (+)For a depression measurement..........................Connect the crystal tube to the left-hand connector (-)For a differential pressure..................................Connect the highest pressure to the right-hand connector (+) and the lowest pressure to the left

hand connector (-)

MAINTENANCE :

HP manometers require no special maintenance other than simply changing the reading liquid once a year.

Ref. F

Tang

– HP

– 01

/99 A

- RC

S 24

(24)

Pér

igueu

x 349

282 0

95 N

on-co

ntrac

tual d

ocum

ent –

We r

eser

ve th

e righ

t to m

odify

the c

hara

cteris

tics o

f our

pro

ducts

with

out p

rior n

otice

.

Zero adjustment By moving the graduated slide strip, travel 12 mmFixed in place via milled, nickel-plated brass screw.

DIMENSIONS

Reference HP 5 HP 10 HP 15

bcdef

Weight

184 mm116 mm80 mm30 mm

180 mm71 mm340 g

234 mm166 mm80 mm30 mm

230 mm71 mm430 g

234 mm166 mm80 mm30 mm

230 mm71 mm430 g

a

ab

c

ed

f


PORTABLE MANOMETERSWITH VERTICAL LIQUID COLUMN

KM serie

The KM vertical liquid column portable manometer, developed and manufactured by KIMO, measures low pressures in gas networks.

● Easy to carry.● "U"- shaped column for pressure and depression measurement.● Direct read-off by moving the gratuated slide strip.● Safety valves actuation for momentaneous overshooting of the scale.● Fitted with valve connectors and mounting hook.● Supplied with connection sleeves, a bottle of VOLT 1S liquid and carrying case.

KEY POINTS

DIMENSIONS

Reference

KM 45

Dimensions (height. x width x thickness)

306 X 50 X 20 mm

Weight (with accessories)

550 g

Reference

KM 45

Measuring range

0 – 45 mbar

Resolution

0.2 mbar

MEASURING RANGE



Possible range of usePression statique maximumManometer body

Graduated slide stripZero adjustment


From +5 to +30°CFrom -30 to +60°C8 bars15 mm thick transparent Altuglas.

By moving the gratuated slide stripFixed in place via milled, nickel-plated brass screw. VOLT 1S, density 1.86 at 20°C.On Ø 6.2 nickel-plated brass valve connectors, with 1m long neoprene tube fitted with dedicated end-pieces for gas equipment.

1. Dismount one of the 2 connectors using a no.12 spanner and slacken the milled head of the other connector by one turn.2. Check beforehand that the slide strip is at its lowest level.3. Pour the liquid in the column using the spout.4. Do not overfill. Never go beyond the NL line at the middle of the slide strip.5. Remount the connector and screw the milled head of the other connector back down.

Altuglas transparent

TECHNICAL FEATURES

MOUNTING

OPERATION

1. Hang up the manometer vertically by the mounting hook or hold manually.2. Open to the air by slackening the milled heads of the 2 valves (one turn is sufficient).3. Push one of the ends of the connecting tube firmly onto the right-hand valve. Push the other end of the tube onto the pressure point of the pipeline or the instrument which has to be checked.4. The liquid, under gas pressure, decreases in the right column and rises in the left one. If the gas flow occurs too hard and plays the safety valve, repeat the operation by pinching the connecting tube more or less strongly to admit the gas more slowly (if the safety valve is working again, it is because the pressure control exceeds the measuring range of the manomters)5. When the liquid has settled, slide the graduated strip so as to bring the zero mark opposite the right-hand tube's liquid level (lowest level).6. The graduation corresponding to the height of the liquid in the left-hand tube indicates the exact gas pressure.7. Close off the 2 valves securely after operation

Ref. F

Tang

– KM

–20/

10/11

- RC

S 24

(24)

Pér

igueu

x 349

282 0

95 N

on-co

ntrac

tual d

ocum

ent –

We r

eser

ve th

e righ

t to m

odify

the c

hara

cteris

tics o

f our

pro

ducts

with

out p

rior n

otice

.

IMPORTANT :• Only VOLT1S liquid will ensure precise measurement (slide scale graduation corresponding to the density of this liquid). • Maximum static pressure : 8 bars

Liquid column

Recommended range of use

Ø 4 mm bored into the solid block.


KX seriesINCLINED LIQUID

COLUMN MANOMETERS

The KX range of inclined liquid column manometers, developed and manufactured by KIMO, measure slight variations in pressure, depression or differential pressure of air or gas.They are for use in the following applications : treatment of air, ventilation, air conditioning, heating, dust elimination...

● Scale with centered zero.● Possibility for measuring positive and negative pressures.● Zero adjusting by moving the slide strip.● Integrated spirit level for adjusting horizontality● Supplied with a white PVC support, 2 screws and 2 rawlplugs, two 487 connectors and a bottle of AWS 10 liquid.

MEASURING RANGE

Resolution

1 mm CE or 10 Pa1 mm CE or 10 Pa

Sensitivity scaleFor 1 mm CE or 10 PA

3 mm2.5 mm400 – 0 – 400

250 – 0 – 250Pascal

25 – 0 – 2540 – 0 – 40

mm CEMeasuring range*Reference

KX 205KX 404

*Also exists in DaPa..

KEY POINTS



TECHNICAL FEATURES

Recommended range of useTempérature d'utilisation possibleMaximum static pressureManometer bodyLiquid columnGraduated slide stripZero adjustment

Positioning


Wall-mounted

From +5 to +30°CFrom -30 to +60°C6 barsTransparent 15 mm thick Altuglas.entirely bored in the solid block, Ø 4mm.Transparent Altuglas. Cross-section 20 x 2 mm.By moving the graduated slide strip, travel 12 mm.Fixed in place via milled, nickel-plated brass screw.Horizontal positioning via integrated spirit level and milled, nickel-plated brass adjusting screw, vertical travel 12 mm.AWS 10 red oil, density 0.87 at 15°C20 mlØ 5x8 mm semi-rigit crystal tube, on Ø 6.2 mm ribbed, nickel-plated brass connectors, 1/8 gas thread.With or without white PVC support.

DIMENSIONS

Reference KX 205 KX404

abcdef

weight

178 mm110 mm117 mm25 mm

174 mm109 mm

420 g

219 mm

25 mm

151 mm154 mm

215 mm129 mm

660 g

MOUNTING

1. Mount the manometer on a wall or a vertical partition wall with two maximum Ø 5 x 25 mm screws.2. Set horizontality by using the integrated level and the milled adjusting screw.3. Unscrew the connector on the reservoir and slowly pour the manometric liquid to zero point on the graduation.4. Remount the connector without overtightening.5. Connect the manometer with the Ø 5x8 mm crystal tube to the pressure or depression source to be checked.

NOTE :

For a pressure measurement..............................Connect the crystal tube to the right-hand connector (+)For a depression measurement..........................Connect the crystal tube to the left-hand connector (-)For a differential pressure..................................Connect the highest pressure to the right-hand connector (+) and the lowest pressure to the left

hand connector (-)

MAINTENANCE :KX manometers require no special maintenance other than simply changing the reading liquid once a year.

Ref. F

Tang

– KX

– 05

/08 B

- RC

S 24

(24)

Pér

igueu

x 349

282 0

95 N

on-co

ntrac

tual d

ocum

ent –

We r

eser

ve th

e righ

t to m

odify

the c

hara

cteris

tics o

f our

pro

ducts

with

out p

rior n

otice

.

ab

c

e

f

d


LU 400


LU series

The LU range of vertical liquid column manometers, developed and manufactured by KIMO, are mainly for measuring variations of pressure, depression or differential pressure of air or gas within measurement ranges which vary according to the type of manometric liquid used : AWS 10, VOLT 1S or MERCURY.(See table below)

● ''U''-shaped column for measuring consecutively positive and negative pressures● Measurement by addition of values read on each column● Zero adjustment by moving the slide strip● For fixed use regardless of the manometric liquid used● For portable use with the LU model using VOLT 1S liquid● Supplied with a white PVC support, 2 screws and 2 rawlplugs, two 487 connectors and bottle of liquid

MEASURING RANGE

KEY POINTS


Liquide AWS 10

Liquide VOLT 1S

Mercure

Measuring range

Measuring range

Measuring range

mm CE

mm CE

mm HG

mbar

mbar

mbar

LU 100 LU 20050 – 0 – 50 100 – 0 – 100 200 – 0 – 200

20 – 0 – 2010 – 0 – 105 – 0 – 5

110 – 0 – 110 220 – 0 – 220 430 – 0 – 43043 – 0 – 4322 – 0 – 2211 – 0 – 11

50 – 0 – 50 120 – 0 – 120 240 – 0 – 240310 – 0 – 310160 – 0 – 16080 – 0 – 80

Resolution : 1 mm CE or 0.5 mbar

Résolution : 5 mm CE or 1 mbar

Resolution : 1 mm HG or 10 mbar


Recommended range of usePossible range of useMaximum static pressureManometer bodyLiquid columnGraduated slide stripZero adjustment


Wall mounting

From +5 to +30°CFrom -30 to +60°C6 barsTransparent Altuglas of 15 mm thickØ 4 mm tube in extruded Altuglas.Altuglas transparent. Section 40 X 2 mmBy moving the graduated slide strip, travel 10 mm.Fixed via milled, nickel-plated brass screwAWS 10 liquid, density 0.86, VOLT 1S liquid, density 1.86 or mercury, density 13.545Ø 5x8 mm semi-rigid crystal tube on Ø 6.2 nickel-plated brass ribbed connectors (for manometers using AWS 10 or VOLT 1S liquid) or in Delrin (for mercury manometer), 1/8 gas threadWith or without white PVC support.

REF. LU 100

abcde

1. Mount the manometer on a wall or partition wall with two maximum Ø 5 screws.2. Unscrew the left-hand connector and slowly pour the manometric liquid to zero point on the graduation3. Remount the connector without overtightening.4. Connect the manometer with the Ø 5x8 mm crystal tube to the pressure or depression source to be checked.

REMARQUES :For a pressure measurement..............................Connect the crystal tube to one of the two connectorsFor a depression measurement..........................Connect the crystal tube to one of the two connectors.For a differential pressure measurement...........Connect both tubes to both connectors

TECHNICAL FEATURES

LU 200 LU 400

ENCOMBREMENT

MOUNTING

Ref. F

Tang

– LU

– 17

/08/11

- RC

S 24

(24)

Pér

igueu

x 349

282 0

95 N

on-co

ntrac

tual d

ocum

ent –

We r

eser

ve th

e righ

t to m

odify

the c

hara

cteris

tics o

f our

pro

ducts

with

out p

rior n

otice

.


Weight

57 mm207 mm25 mm50 mm

169 mm193 mm260 g

57 mm324 mm25 mm50 mm286 mm310 mm400 g

57 mm558 mm25 mm50 mm

520 mm544 mm

730 g

a

12,43

cme

b

d c


MG seriesINCLINED LIQUID

COLUMN MANOMETERS

The MG range of inclined liquid column manometers, developed and manufactured by KIMO, measure slight variations in pressure, depression or differential pressure of air or gas.They are for use in the following applications : treatment of air, ventilation, air conditioning, heating, dust elimination...

● Zero adjustement by moving the slide strip● Safety reservoir enabling momentaneous overshooting of the scale● Integrated spirit level for adjusting horizontality● Supplied with a white PVC support, two screws and two rawplugs, two 487 connectors and a bottle of AWS 10 liquid

KEY POINTS

MEASURING RANGE

Resolution

0,5 mm CE or 5 Pa


8 mm0 – 200Pascal

0 – 20mm CE

Measuring range*Reference

MG 201 mm CE or 10 Pa3 mm0 – 5000 – 50MG 50


2.5 mm0 – 8000 – 80MG 80 1 mm CE or 10 Pa

* Also exists in DaPa


TECHNICAL FEATURES


Positionning


Wall-mounted

From +5 to +30°CFrom -30 to +60°C6 barsTransparent 15 mm thick Altuglas Entirely bored in the solid block, Ø 4 mmTransparent Altuglas. Cross-section 20 X 2 mm

Horizontal positioning via integrated spirit level and milled, nickel-plated brass adjusting screw, vertical travel 12 mm.AWS 10 red oil, density 0.87 at 15°C20 mlØ 5 X 8 mm semi-rigid crystal tube, on Ø 6,2 mm ribbed, nickel-plated brass connectors, 1/8 gas threadWith or without white PVC support

MOUNTING

1. Mount on a wall or a vertical partition wall with two maximum Ø 5 x 25 mm screws (supplied).2. Set horizontality using the integrated level and the milled adjusting screw.3. Unscrew the connector on the reservoir and slowly pour the manometric liquid to zero point on the graduation.4. Remount the connector without overtightening.5. Connect the manometer with the Ø 5 X 8 mm crystal tube to the pressure or depression source to be checked.

NOTE :For a pressure measurement..............................Connect the crystal tube to the right-hand connector (+)For a depression measurement..........................Connect the crystal tube to the left-hand connector (-)For a differential pressure..................................Connect the highest pressure to the right-hand connector (+) and the lowest pressure to the left

hand connector (-)MAINTENANCE :MG manometers require no special maintenance other than simply changing the reading liquid once a year.

Ref. F

Tang

– M

G – 1

7/08/1

1 - R

CS 2

4 (24

) Pér

igueu

x 349

282 0

95 N

on-co

ntrac

tual d

ocum

ent –

We r

eser

ve th

e righ

t to m

odify

the c

hara

cteris

tics o

f our

pro

ducts

with

out p

rior n

otice

.

Zero adjustment By moving the graduated slide strip, travel 20 mm.Fixed via milled, nickel-plated brass screw

DIMENSIONS

a

c

ed

f


Ø 6 mm

b

Reference MG 20 MG 50

bcdef

196 mm128 mm80 mm25 mm

192 mm55 mm320 g

178 mm110 mm117 mm25 mm

174 mm109 mm

aMG 80

219 mm151 mm154 mm25 mm215 mm129 mm

660 g420 gWeight


MT40INCLINED LIQUID

COLUMN MANOMETERS

The MT range of inclined liquid column portable manometers, developed and manufactured by KIMO, are particulary recommended for those in the heating trade for checking pressures in chimney flues, combustion chambers, filters...

● Easy to carry● Safety reservoir enabling momentaneous overshooting of the scale● Zero adjustment by moving the slide strip● Integrated spirit level for adjusting horizontality.● Equipped with valve connectors, magnetic fixations, support with base plate● Can be used for measuring speeds with Pitot tube.● Supplied with connecting sleeves, bottle of VOLT 1 S liquid and travelling case.

KEY POINTS

MEASURING RANGE

Résolution

1 mm CE

Sensitivity scaleFor 1 mm CE

4 mm0 – 40

Measuring range (mm CE)Reference

MT 40



TECHNICAL FEATURES


Positionning


From +5 to +30°CFrom -30 to +60°C6 barsTransparent 15 mm thick Altuglas Entirely bored in the solid block, Ø 4 mmTransparent Altuglas. Cross-section 20 X 2 mm

Horizontal positioning via integrated spirit level and milled, nickel-plated brass adjusting screw, vertical travel 12 mm.VOLT 1S oil - density 1.86 at 20°C.20 mlon valve connectors in nickel-plated brass Ø 6.2 mm neoprene tubes with connecting sleeves.

MOUNTING

1. Place the manometer on a horizontal surface or a vertical partition wall by using the magnetic fixations.2. Set horizontality by using the integrated level and the milled adjusting screw.3. Unscrew the connector on the reservoir and slacken the milled wheel on the other connecter by one turn.4. Slowly pour the manometric liquid to zero point on the graduation.5. Remount the connector without overtightening.6.Connect the manometer with the tube provided to the pressure or depression source to be checked.

NOTE :For a pressure measurement..............................Connect the crystal tube to the right-hand connector (+)For a depression measurement..........................Connect the crystal tube to the left-hand connector (-)For a differential pressure..................................Connect the highest pressure to the right-hand connector (+) and the lowest pressure to the left

hand connector (-)MAINTENANCE :MT40 manometer requires no special maintenance other than simply changing the reading liquid once a year.

Ref. F

Tang

– M

T – 1

7/08/1

1 - R

CS 2

4 (24

) Pér

igueu

x 349

282 0

95 N

on-co

ntrac

tual d

ocum

ent –

We r

eser

ve th

e righ

t to m

odify

the c

hara

cteris

tics o

f our

pro

ducts

with

out p

rior n

otice

.

Zero adjustment By moving the graduated slide strip, travel 20 mm.Fixed via milled, nickel-plated brass screw

DIMENSIONS

a

d

e


c

b

ReferenceMT 40

a b c d e Weight193 mm 208 mm 93 mm 37 mm 80 mm 800 g


TJ 1000

0 – 215

TJ series

The TJ range of vertical liquid column manometers, developed and manufactured by KIMO, are mainly for measuring variations of pressure, depression or differential pressure of air or gas within measurement ranges which vary according to the type of manometric liquid used : AWS 10, VOLT 1S or MERCURY.(See table below)

● "J"- shaped column for direct measuring.● Zero adjustment by moving the slide strip.● For fixed use regardless of the manometric liquid used.● For portable use with the TJ model using VOLT 1S liquid.● Supplied with a white PVC support, 2 screws and 2 rawlplugs, two 487 connectors and a bottle of liquid.

MEASURING RANGE

KEY POINTS


AWS 10liquid

VOLT 1Sliquid

Mercury

Measuring range

Measuring range

Measuring range

mm CE

mm CE

mm HG

mbar

mbar

mbar

TJ 100 TJ 300 TJ 6000 – 100 0 – 300 0 – 600 0 – 1000

0 – 1000 – 600 – 300 – 10

– 0 – 650 0 – 1300 0 – 21500 – 1300 – 65–

– 0 – 350 0 – 690 0 – 11600 – 15500 – 9200 – 470–

Resolution : 1 mm CE or 0.5 mbar

Resolution : 5 mm CE or 1 mbar

Resolution : 1 mm HG or 10 mbar

TJ 1500 – 1500 – 15

––

––



Recommended range of usePossible range of useMaximum static pressureMAnometer boyLiquid columnGraduated slide stripZero adjustment


Wall-mounted

From +5 to +30°CFrom -30 to +60°C6 barsTransparent 15 mm thick Altuglas Ø 4mm tube in extruded Altuglas.Transparent Altuglas. Cross-section 23 x 3 mm.moving the gratuated slide strip, travel 15 mmFixed in place via milled, nickel-plated brass screw.

AWS 10 liquid, density 0.86 ; VOLT 1S liquid, density 1.86 or mercury, density 13.545Ø 5x8 mm semi-rigid crystal tube on Ø 6.2 nickel-plated brass ribbed connectors (for manometers using AWS 10 or VOLT 1S liquid) or in Delrin (for mercury manometer), 1/8 gas thread.With or without white PVC support.

REF. TJ 100

abcde

1. Mount the manometer on a wall or partition wall with two maximum Ø 5 screws.2. Unscrew one of the two connectors and slowly pour the manometric liquid to zero point on the graduation.3. Remount the connector without overtightening4. Connect the manometer with the Ø 5x8 mm crystal tube to the pressure or depression source to be checked.

NOTE :

For a pressure measurement..................Connect the crystal tube to the right-hand connector (+)For a depression measurement..............Connect the crystal tube to the left-hand connector (-)For a differential pressure......................Connect the highest pressure to the right-hand connector(+)

and the lowest pressure to the left hand connector (-)

TECHNICAL FEATURES

TJ 300 TJ 600 TJ 1000

DIMENSIONS

MOUNTING

Ref. F

Tang

– TJ

– 17

/08/11

- RC

S 24

(24)

Pér

igueu

x 349

282 0

95 N

on-co

ntrac

tual d

ocum

ent –

We r

eser

ve th

e righ

t to m

odify

the c

hara

cteris

tics o

f our

pro

ducts

with

out p

rior n

otice

.


Weight

57 mm185 mm25 mm52 mm

147 mm171 mm

290 g

57 mm430 mm25 mm

392 mm416 mm

450 g

57 mm777 mm25 mm

739 mm763 mm

790 g

57 mm1239 mm

25 mm

1201 mm1225 mm

1280 g

a

d

eb

c

Reservoir capacity 20 ml

Cylindrical 1/8 gas connectors.

Ø 6 mm

TJ 150

57 mm243 mm25 mm

205 mm229 mm

310 g

52 mm 52 mm 52 mm 52 mm


TX seriesINCLINED LIQUID

COLUMN MANOMETERS

The TX range of inclined liquid column manometers, developed and manufactured by KIMO, measure slight variations in pressure, depression or differential pressure.They are particulary recommended for measuring overpressures and depressions in clean rooms, operating blocks, laboratories, aseptic rooms, laminar flows...

● Scale with centered zero● Possibility for measuring positive and negative pressures● High measurement sensitivity● Very low pressure ranges● Zero adjusting by moving the slide strip● Integrated spirit level for adjusting horizontality● Supplied with a white PVC support, 2 screws and 2 rawlplugs, two 487 connectors and a bottle of AWS 10 liquid.

KEY POINTS

MEASURING RANGE

Resolution

0.1 mm CE or 1 Pa0.1 mm CE or 1 Pa


20 mm15 mm50 – 0 – 50

25 – 0 – 25Pascal

2.5 – 0 – 2,55 – 0 – 5

mm CEMeasuring range

Reference

TX 25TX 50

0.1 mm CE or 1 Pa10 mm75 – 0 – 757.5 – 0 – 7.5TX 75

Pression / Dépression


TECHNICAL FEATURES


Positioning


Wall-mounted

From +5 to +30°CFrom -30 to +60°C6 barsTransparent 20 mm thick AltuglasEntirely bored in the solid block, Ø 4mm.Transparent Altuglas. Cross-section 20 x 2 mm

Horizontal positioning via integrated spirit level and milled, nickel-plated brass adjusting screw, vertical travel 12 mm.AWS 10 red oil, density 0.87 at 15°C.20 mlConnection : Ø 5x8 mm semi-rigid crystal tube, on Ø 6.2 mm ribbed, nickel-plated brass connectors, 1/8 gas threadWith or without white PVC support.

MOUNTING

1. Mount the manometer on a wall or a vertical partition wall with two maximum Ø 5 x 25 mm screws.2. Set horizontality by using the integrated level and the milled adjusting screw.3. Unscrew the connector on the reservoir and slowly pour the manometric liquid to zero point on the graduation.4. Remount the connector without overtightening.5. Connect the manometer with the Ø 5x8 mm crystal tube to the pressure or depression source to be checked.

NOTE : For a pressure measurement..............................Connect the crystal tube to the right-hand connector (+)For a depression measurement..........................Connect the crystal tube to the left-hand connector (-)For a differential pressure..................................Connect the highest pressure to the right-hand connector (+) and the lowest pressure to the left

hand connector (-)

MAINTENANCE :

TX manometers require no special maintenance other than simply changing the reading liquid once a year.

Ref. F

Tang

– TX

– 02

/99 A

- RC

S 24

(24)

Pér

igueu

x 349

282 0

95 N

on-co

ntrac

tual d

ocum

ent –

We r

eser

ve th

e righ

t to m

odify

the c

hara

cteris

tics o

f our

pro

ducts

with

out p

rior n

otice

.

Zero adjustment By moving the graduated slide strip, travel 12 mm.Fixed in place via milled, nickel-plated brass screw.

DIMENSIONS

Référence TX 25 TX 50 TX 75

bcdef

poids

184 mm116 mm80 mm30 mm

180 mm71 mm340 g

234 mm166 mm80 mm30 mm

230 mm71 mm430 g

234 mm166 mm80 mm30 mm

230 mm71 mm430 g

a

a

c

b

e d

f


VH seriesINCLINED LIQUID

COLUMN MANOMETERS

The VH range of inclined liquid column manometers, developed and manufactured by KIMO, measure slight variations in pressure, depression or differential pressure of air or gas.They are particulary recommended for checking clogging of filters in the ventilation and dust elimination industry.

● Horizontale V-shaped liquid column.● Dual measuring range● Different sensitivity on the two measuring ranges● Zero adjustment via float● Compact dimensions● Integrated spirit level for adjusting horizontality● Supplied with a white PVC support, 2 screws and 2 rawlplugs, two 487 connectors and a bottle of AWS 10 liquid.

KEY POINTS

MEASURING RANGE

Resolution

1 mm CE or 10 Pa


3.5 mm

Pascalmm CEMeasuring range

Reference

VH 50


Total 1st column 2nd column Total 1st column0 – 50 0 – 16 19 – 50 0 – 500 0 – 160 190 – 500 7 mm

1st and 2nd column1st column 2nd column2nd column

The VH 50 also exists in DaPa.


TECHNICAL FEATURES

Recommended range of usePossible range of useMaximum static pressureManometer bodyLiquid columnGraduation

Positioning


Wall-mount

From +5 to +30°CFrom -30 to +60°C1 barTransparent 15 mm thick Altuglas.Entirely bored in the solid block, Ø 4 mm.Directly silk-screened onto the rear face.

Horizontal positioning via integrated spirit level and milled, nickel-plated brass adjusting screw, vertical travel 12 mm.AWS 10 red oil, density 0.87 at 15°C.20 mlØ 5x8 mm semi-rigid crystal tube, on Ø 6.2 mm ribbed, nickel-plated brass connectors,1/8 gas thread.With or without white PVC support.

MOUNTING

1. Mount the manometer on a wall or a vertical partition wall with two maximum Ø 5 screws.2. Set horizontality by using the integrated level and the milled adjusting screw.3. Unscrew the connector on the reservoir and slowly pour the manometric liquid to zero point on the graduation.4. Remount the connector without overtightening.5. Connect the manometer with the Ø 5x8 mm crystal tube to the pressure or depression source to be checked.

NOTE :For a pressure measurement.............................. Connect the crystal tube to the right-hand connector (+)For a depression measurement.......................... Connect the crystal tube to the left-hand connector (-)For a differential pressure.................................. Connect the highest pressure to the right-hand connector (+) and the lowest pressure to the left

hand connector (-)

MAINTENANCE :

VH manometers require no special maintenance other than simply changing the reading liquid once a year.

Zero adjustment By moving the Altuglas float and the milled, nickel-plated brass screw, travel 10 mm.

DIMENSIONS

Reference VH 50

bcdef

Weight

a

a

4cm c

b

6.88cm d

3.68c

mf

188 mm120 mm112 mm25 mm

182 mm101 mm

380 ge

Ø 6 mm


Ref. F

Tang

– VH

– 17

/08/1

1 - R

CS 2

4 (24

) Pér

igueu

x 349

282 0

95 N

on-co

ntrac

tual d

ocum

ent –

We r

eser

ve th

e righ

t to m

odify

the c

hara

cteris

tics o

f our

pro

ducts

with

out p

rior n

otice

.


ACCESSORIES FOR MANOMETERS

TUBES

Ref. TC 5 X 8Clear tube Ø 5 x 8, for permanent installation (m/l or 25 m).

Silicone tube Ø 4 x 7 in black or white, for test instruments (m/l).

Ref. TS 4 X 7

MANOMETER LIQUIDS

Ref. AWS 10Density = 0,87. Bottles of : 20 ml, 30 ml, 125 ml, 250 ml, 500 ml, 1000 ml.

Ref. VOLT 1SDensity = 1,86. Bottles of : 10 ml, 20 ml, 30 ml, 125 ml.

Ref. HGDensity = 13,545. Bottles of : 10 ml, 20 ml, 30 ml, 125 ml.

Ref. VF1Density = 1. Bottles of : 20 ml, 30 ml, 125 ml, 250 ml, 500 ml, 1000 ml.

Ref. TETRA BROMUREDensity = 2,96. Bottles of : 20 ml, 30 ml, 125 ml.

PRESSURE CONNECTIONS :

Ref. KR 483Connection kit with 2 quick connections n° 483 and 2 m of clear tube.

Ref. DP 447Connection for double-shell wall, maximum thickness : 30 mm.Drilling diameter : 6 mm.

Ref. DP 339Connection for double-shell wall maximum thickness : 80 mm. Drilling diameter : 6 mm.

Ref. 483Quick-connection for wall without rear access.Drilling diameter : 10 mm.

Ref. 482Simple conection with rear nut, M5 threading, length 15 mm. Drilling diameter : 5 mm.

Ref. PC 482Through-connection for partitions standard lengths 35 to 190 mm. Other lengths on request.Drilling diameter :11 mm.


MANOMETERS CONNECTIONS :

Ref. 487Simple connection in chromed brass for all type of manometers using AWS 10 and VOLT 1S. Thread : 1/8 gas.

Ref. 509Chromed brass safety connection, eliminating overspill on manometer using AWS 10 and VOLT 1S. Thread : 1/8 gas.

Ref. 505Valve connection in chromed brass for portable MT, KM, TJ and LU manometer using VOLT 1S liquid.Thread : 1/8 gas.

Ref. 484Simple connection in nylon for TJ and LU mercury manometers.Thread : 1/8 gas.

Ref. 466Simple connection in nylon for GF manometers, using VF1 and HG liquid.Thread : 7 x 100.

Ref. 555 M/FMale / female, 1/8 gas ball valve, for manometer isolation.

Ref. 555 F/FFemale / female, 1/8 gas ball valve, for manometer isolation.

Ref. 666Male / female, 1/8 connection,air vent valve with a slide block to set the zero point without disconnecting the tubes.

JUNCTIONS

Ref. J.D.CStraight connection for Ø 5 x 8 tube.

Ref. J.T.CT-connection for Ø 5 x 8 tube.

Ref. J.Y.CY-connection for Ø 5 x 8 tube.

ACCESSORIES

Ref. 494Pressure tube, length 1 m for MT and KM manometers. With moulded ends.

Ref. GPN 900Plug -8,5 A for all Ø 6,2 mm connections. 10 units bag.

Ref. FM-KS.10Set of 2 magnetic fixings.

Ref. 648-FMSafety reservoir, with magnetic fixings for mercury manometers.

Ref. 648-PFSafety reservoir, permanent fixing for mercury manometers.

Ref. ALTU.Altunet cleaning product, 500 ml bottle..

Ref. F

Tang

– Ac

cess

oires

– 02

/05 B

- RC

S 24

(24)

Pér

igueu

x 349

282 0

95 N

on-co

ntrac

tual

docu

ment

– We r

eser

ve th

e rig

ht to

modif

y the

char

acter

istics

of ou

r pro

ducts

with

out p

rior n

otice

.


CP series INCLINED LIQUID COLUMN MANOMETERS · For a pressure measurement ... HP series INCLINED LIQUID COLUMN MANOMETERS The HP range of inclined liquid column manometers, developed

Documents