-
Installation Instructions
Original Instructions
ControlLogix 5580 ControllersCatalog Numbers 1756-L81E,
1756-L81EK, 1756-L82E, 1756-L82EK, 1756-L83E, 1756-L83EK,
1756-L84E, 1756-L84EK, 1756-L85E, 1756-L85EK
The ControlLogix 5580 controllers help enable faster system
performance, capacity, productivity, and security to help meet the
growing demands of smart machines and equipment for
manufacturing.
Integrated Motion over EtherNet/IP for up to 256 axes. 1 Gb
embedded Ethernet port enables high performance, communications,
I/O, and motion control. Secure Digital (SD) card provides optional
nonvolatile memory to store user program and tag data on the
controller. Studio 5000 Automation Engineering & Design
Environment provides ease of system design and commissioning.
Digitally signed and encrypted firmware helps protect against
malicious intent. FactoryTalk Security provides centralized
authentication and access control by verifying the identity of each
user-access attempt to the
system. Display provides enhanced diagnostics and
troubleshooting.
Topic Page
Parts List 5
Required System Components 5
Product Dimensions 5
Install the Controller 6
Install the SD Card 7
Connect to an EtherNet/IP Network 7
Confirm Installation 7
Specifications 8
Additional Resources 8
-
ControlLogix 5580 Controllers
ATTENTION: Read this document and the documents listed in the
Additional Resources section about installation, configuration and
operation of this equipment before you install, configure, operate
or maintain this product. Users are required to familiarize
themselves with installation and wiring instructions in addition to
requirements of all applicable codes, laws, and
standards.Activities including installation, adjustments, putting
into service, use, assembly, disassembly, and maintenance are
required to be carried out by suitably trained personnel in
accordance with applicable code of practice.If this equipment is
used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
ATENCIN: Antes de instalar, configurar, poner en funcionamiento
o realizar el mantenimiento de este producto, lea este documento y
los documentos listados en la seccin Recursos adicionales acerca de
la instalacin, configuracin y operacin de este equipo. Los usuarios
deben familiarizarse con las instrucciones de instalacin y cableado
y con los requisitos de todos los cdigos, leyes y estndares
vigentes.El personal debidamente capacitado debe realizar las
actividades relacionadas a la instalacin, ajustes, puesta en
servicio, uso, ensamblaje, desensamblaje y mantenimiento de
conformidad con el cdigo de prctica aplicable.Si este equipo se usa
de una manera no especificada por el fabricante, la proteccin
provista por el equipo puede resultar afectada.ATENO: Leia este e
os demais documentos sobre instalao, configurao e operao do
equipamento que esto na seo Recursos adicionais antes de instalar,
configurar, operar ou manter este produto. Os usurios devem se
familiarizar com as instrues de instalao e fiao alm das
especificaes para todos os cdigos, leis e normas aplicveis.
necessrio que as atividades, incluindo instalao, ajustes, colocao
em servio, utilizao, montagem, desmontagem e manuteno sejam
realizadas por pessoal qualificado e especializado, de acordo com o
cdigo de prtica aplicvel. Caso este equipamento seja utilizado de
maneira no estabelecida pelo fabricante, a proteo fornecida pelo
equipamento pode ficar prejudicada.: , , , , . , . , , . , , , , ,
, , . , . :
ACHTUNG: Lesen Sie dieses Dokument und die im Abschnitt Weitere
Informationenaufgefhrten Dokumente, die Informationen zu
Installation, Konfiguration und Bedienung dieses Produkts
enthalten, bevor Sie dieses Produkt installieren, konfigurieren,
bedienen oder warten. Anwender mssen sich neben den Bestimmungen
aller anwendbaren Vorschriften, Gesetze und Normen zustzlich mit
den Installations- und Verdrahtungsanweisungen vertraut
machen.Arbeiten im Rahmen der Installation, Anpassung,
Inbetriebnahme, Verwendung, Montage, Demontage oder Instandhaltung
drfen nur durch ausreichend geschulte Mitarbeiter und in
bereinstimmung mit den anwendbaren Ausfhrungsvorschriften
vorgenommen werden.Wenn das Gert in einer Weise verwendet wird, die
vom Hersteller nicht vorgesehen ist, kann die Schutzfunktion
beeintrchtigt sein.ATTENTION : Lisez ce document et les documents
lists dans la section Ressources complmentaires relatifs
linstallation, la configuration et le fonctionnement de cet
quipement avant dinstaller, configurer, utiliser ou entretenir ce
produit. Les utilisateurs doivent se familiariser avec les
instructions dinstallation et de cblage en plus des exigences
relatives aux codes, lois et normes en vigueur.Les activits
relatives linstallation, le rglage, la mise en service,
lutilisation, lassemblage, le dmontage et lentretien doivent tre
ralises par des personnes formes selon le code de pratique en
vigueur.Si cet quipement est utilis dune faon qui na pas t dfinie
par le fabricant, la protection fournie par lquipement peut tre
compromise. : , , , . , .
, , , , , , .
.ATTENZIONE Prima di installare, configurare ed utilizzare il
prodotto, o effettuare interventi di manutenzione su di esso,
leggere il presente documento ed i documenti elencati nella sezione
Altre risorse, riguardanti linstallazione, la configurazione ed il
funzionamento dellapparecchiatura. Gli utenti devono leggere e
comprendere le istruzioni di installazione e cablaggio, oltre ai
requisiti previsti dalle leggi, codici e standard applicabili.Le
attivit come installazione, regolazioni, utilizzo, assemblaggio,
disassemblaggio e manutenzione devono essere svolte da personale
adeguatamente addestrato, nel rispetto delle procedure
previste.Qualora lapparecchio venga utilizzato con modalit diverse
da quanto previsto dal produttore, la sua funzione di protezione
potrebbe venire compromessa.DKKAT: Bu rnn kurulumu, yaplandrlmas,
iletilmesi veya bakm ncesinde bu dokman ve bu ekipmann kurulumu,
yaplandrlmas ve iletimi ile ilgili lave Kaynaklar blmnde yer
listelenmi dokmanlar okuyun. Kullanclar yrrlkteki tm ynetmelikler,
yasalar ve standartlarn gereksinimlerine ek olarak kurulum ve
kablolama talimatlarn da renmek zorundadr.Kurulum, ayarlama,
hizmete alma, kullanma, paralar birletirme, paralar skme ve bakm
gibi aktiviteler sadece uygun eitimleri alm kiiler tarafndan
yrrlkteki uygulama ynetmeliklerine uygun ekilde yaplabilir.Bu
ekipman retici tarafndan belirlenmi amacn dnda kullanlrsa, ekipman
tarafndan salanan koruma bozulabilir.
POZOR: Ne zanete instalovat, konfigurovat i provozovat tento
vrobek nebo provdt jeho drbu, pette si tento dokument a dokumenty
uveden v sti Dodaten zdroje ohledn instalace, konfigurace a provozu
tohoto zazen. Uivatel se musej vedle poadavk vech relevantnch
vyhlek, zkon a norem nutn seznmit tak s pokyny pro instalaci a
elektrick zapojen.innosti zahrnujc instalaci, nastaven, uveden do
provozu, uvn, mont, demont a drbu mus vykonvat vhodn prokolen
personl v souladu s pslunmi provdcmi pedpisy.Pokud se toto zazen
pouv zpsobem neodpovdajcm specifikaci vrobce, me bt naruena
ochrana, kterou toto zazen poskytuje.UWAGA: Przed instalacj,
konfiguracj, uytkowaniem lub konserwacj tego produktu naley
przeczyta niniejszy dokument oraz wszystkie dokumenty wymienione w
sekcji Dodatkowe rda omawiajce instalacj, konfiguracj i procedury
uytkowania tego urzdzenia. Uytkownicy maj obowizek zapozna si z
instrukcjami dotyczcymi instalacji oraz oprzewodowania, jak rwnie z
obowizujcymi kodeksami, prawem i normami.Dziaania obejmujce
instalacj, regulacj, przekazanie do uytkowania, uytkowanie, monta,
demonta oraz konserwacj musz by wykonywane przez odpowiednio
przeszkolony personel zgodnie z obowizujcym kodeksem
postpowania.Jeli urzdzenie jest uytkowane w sposb inny ni okrelony
przez producenta, zabezpieczenie zapewniane przez urzdzenie moe
zosta ograniczone.OBS! Ls detta dokument samt dokumentet, som str
listat i avsnittet vriga resurser, om installation, konfigurering
och drift av denna utrustning innan du installerar, konfigurerar
eller brjar anvnda eller utfra underhllsarbete p produkten.
Anvndare mste bekanta sig med instruktioner fr installation och
kabeldragning, frutom krav enligt gllande koder, lagar och
standarder.tgrder som installation, justering, service, anvndning,
montering, demontering och underhllsarbete mste utfras av personal
med lmplig utbildning enligt lmpligt bruk.Om denna utrustning
anvnds p ett stt som inte anges av tillverkaren kan det hnda att
utrustningens skyddsanordningar frstts ur funktion.LET OP: Lees dit
document en de documenten die genoemd worden in de paragraaf
Aanvullende informatie over de installatie, configuratie en
bediening van deze apparatuur voordat u dit product installeert,
configureert, bediend of onderhoudt. Gebruikers moeten zich
vertrouwd maken met de installatie en de bedradingsinstructies,
naast de vereisten van alle toepasselijke regels, wetten en
normen.Activiteiten zoals het installeren, afstellen, in gebruik
stellen, gebruiken, monteren, demonteren en het uitvoeren van
onderhoud mogen uitsluitend worden uitgevoerd door hiervoor
opgeleid personeel en in overeenstemming met de geldende
praktijkregels.Indien de apparatuur wordt gebruikt op een wijze die
niet is gespecificeerd door de fabrikant, dan bestaat het gevaar
dat de beveiliging van de apparatuur niet goed werkt.
2 Rockwell Automation Publication 1756-IN043A-EN-P - April
2016
-
ControlLogix 5580 Controllers
ATTENTION:
In case of malfunction or damage, no attempts at repair should
be made. The module should be returned to the manufacturer for
repair. Do not dismantle the module.
The USB port is intended for temporary local programming
purposes only and not intended for permanent connection. The USB
cable is not to exceed 3.0 m (9.84 ft) and must not contain
hubs.
Use only a soft dry anti-static cloth to wipe down equipment. Do
not use any cleaning agents. When installed in a 1756 Series C
Chassis, this equipment is certified for use only within the
surrounding air temperature range of
060 C (32140 F). The equipment must not be used outside of this
range. When installed in a 1756 Series B Chassis, this equipment is
certified for use only within the surrounding air temperature range
of 050 C (32122 F). The equipment must not be used outside of this
range.
WARNING:
When you press the reset button while power is on, an electrical
arc can occur. This could cause an explosion in hazardous location
installations. Be sure that power is removed or the area is
nonhazardous before proceeding.
Do not use the USB port in hazardous locations.
North American Hazardous Location Approval
The following information applies when operating this equipment
in hazardous locations. Informations sur lutilisation de cet
quipement en environnements dangereux.
Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for
use in Class I Division 2 Groups A, B, C, D, Hazardous Locations
and nonhazardous locations only. Each product is supplied with
markings on the rating nameplate indicating the hazardous location
temperature code. When combining products within a system, the most
adverse temperature code (lowest "T" number) may be used to help
determine the overall temperature code of the system. Combinations
of equipment in your system are subject to investigation by the
local Authority Having Jurisdiction at the time of
installation.
Les produits marqus "CL I, DIV 2, GP A, B, C, D" ne conviennent
qu' une utilisation en environnements de Classe I Division 2
Groupes A, B, C, D dangereux et non dangereux. Chaque produit est
livr avec des marquages sur sa plaque d'identification qui
indiquent le code de temprature pour les environnements dangereux.
Lorsque plusieurs produits sont combins dans un systme, le code de
temprature le plus dfavorable (code de temprature le plus faible)
peut tre utilis pour dterminer le code de temprature global du
systme. Les combinaisons d'quipements dans le systme sont sujettes
inspection par les autorits locales qualifies au moment de
l'installation.
WARNING:Explosion Hazard Do not disconnect equipment unless
power has been removed or the
area is known to be nonhazardous. Do not disconnect connections
to this equipment unless power has been
removed or the area is known to be nonhazardous. Secure any
external connections that mate to this equipment by using screws,
sliding latches, threaded connectors, or other means provided with
this product.
Substitution of components may impair suitability for Class I,
Division 2. If this product contains batteries, they must only be
changed in an area
known to be nonhazardous.
AVERTISSEMENT:Risque dExplosion Couper le courant ou s'assurer
que l'environnement est class non dangereux
avant de dbrancher l'quipement. Couper le courant ou s'assurer
que l'environnement est class non dangereux
avant de dbrancher les connecteurs. Fixer tous les connecteurs
externes relis cet quipement l'aide de vis, loquets coulissants,
connecteurs filets ou autres moyens fournis avec ce produit.
La substitution de composants peut rendre cet quipement inadapt
une utilisation en environnement de Classe I, Division 2.
S'assurer que l'environnement est class non dangereux avant de
changer les piles.
European Hazardous Location Approval
The following applies to products marked , II 3 G: Are Equipment
Group II, Equipment Category 3, and comply with the Essential
Health and Safety Requirements relating to the design and
construction of such equipment
given in Annex II to Directive 94/9/EC. See the EC Declaration
of Conformity at
http://www.rockwellautomation.com/products/certification for
details. The type of protection for is Ex nA IIC T4 Gc according to
EN 60079-15. Comply to standards: EN 60079-0:2012+A11:2013,
EN60079-15:2010, reference certificate number DEMKO13ATEX1325026X.
Are intended for use in areas in which explosive atmospheres caused
by gases, vapors, mists, or air are unlikely to occur, or are
likely to occur only infrequently and for short
periods. Such locations correspond to Zone 2 classification
according to ATEX directive 1999/92/EC. May have catalog numbers
followed by a "K" to indicate a conformal coating option.
IEC Hazardous Location Approval
The following applies to products with IECEx certification: Are
intended for use in areas in which explosive atmospheres caused by
gases, vapors, mists, or air are unlikely to occur, or are likely
to occur only infrequently and for short
periods. Such locations correspond to Zone 2 classification to
IEC 60079-0. The type of protection is Ex nA IIC T4 Gc according to
IEC 60079-15. Such modules comply to Standards IEC 60079-0:6th
Edition, IEC 60079-15:4th Edition, reference IECEx certificate
number IECExUL14.0008X. May have catalog numbers followed by a "K"
to indicate a conformal coating option.
Rockwell Automation Publication 1756-IN043A-EN-P - April 2016
3
http://www.rockwellautomation.com/products/certification
-
ControlLogix 5580 Controllers
Special Conditions for Safe Use
WARNING:
This equipment is not resistant to sunlight or other sources of
UV radiation. This equipment shall be mounted in an ATEX/IECEx Zone
2 certified enclosure with a minimum ingress protection rating of
at least IP54 (as defined in
EN/IEC 60529) and used in an environment of not more than
Pollution Degree 2 (as defined in EN/IEC 60664-1) when applied in
Zone 2 environments. The enclosure must be accessible only by the
use of a tool.
This equipment shall be used within its specified ratings
defined by Rockwell Automation. Provision shall be made to prevent
the rated voltage from being exceeded by transient disturbances of
more than 140% of the rated voltage when applied
in Zone 2 environments. The instructions in the user manual
shall be observed. This equipment must be used only with ATEX/IECEx
certified Rockwell Automation backplanes. Do not disconnect
equipment unless power has been removed or the area is known to be
nonhazardous. The USB port is intended for temporary local
programming purposes only and not intended for permanent
connection. Do not use the USB port in
hazardous locations.
Environment and Enclosure
ATTENTION: This equipment is intended for use in a Pollution
Degree 2 industrial environment, in overvoltage Category II
applications (as defined in EN 60664-1), at altitudes up to 2000 m
(6562 ft) without derating.
This equipment is not intended for use in residential
environments and may not provide adequate protection to radio
communication services in such environments.
This equipment is supplied as open-type equipment for indoor
use. It must be mounted within an enclosure that is suitably
designed for those specific environmental conditions that will be
present and appropriately designed to prevent personal injury
resulting from accessibility to live parts. The enclosure must have
suitable flame-retardant properties to prevent or minimize the
spread of flame, complying with a flame spread rating of 5VA or be
approved for the application if non-metallic. The interior of the
enclosure must be accessible only by the use of a tool. Subsequent
sections of this publication may contain more information regarding
specific enclosure type ratings that are required to comply with
certain product safety certifications.
In addition to this publication, see the following:
Industrial Automation Wiring and Grounding Guidelines,
publication 1770-4.1, for more installation requirements NEMA
Standard 250 and EN/IEC 60529, as applicable, for explanations of
the degrees of protection provided by different types of
enclosure
4 Rockwell Automation Publication 1756-IN043A-EN-P - April
2016
http://literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdf
-
ControlLogix 5580 Controllers
Parts ListThe controller ships with these parts:
A key for the mode switch 2 GB Secure Digital Card (1784-SD2),
pre-installed in the controller
Required System ComponentsTo use the controller, a chassis and
power supply are required. The ControlLogix 5580 controllers are
compatible with these chassis and power supplies.
Product Dimensions
IMPORTANT Any illustrations, charts, sample programs, and layout
examples shown in this publication are intended solely for the
purposes of example. Since there are many variables and
requirements associated with any particular installation, Rockwell
Automation does not assume responsibility or liability for actual
use based upon the examples shown in this publication.
Component Catalog Number
Chassis, series C and series B 1756-A4, 1756-A7, 1756-A10,
1756-A13, 1756-A17
Power supply, standard 1756-PA72, 1756-PA75, 1756-PB72,
1756-PB75, 1756-PC75, 1756-PH75
Power supply, redundant 1756-PA75R, 1756-PB75R, 1756-PSCA2
139.6 mm(5.50 in.)
34.55 mm(1.360 in.)
145.2 mm(5.717 in.)
Rockwell Automation Publication 1756-IN043A-EN-P - April 2016
5
-
ControlLogix 5580 Controllers
Connectors and Status Indicators
Install the Controller
Before you install the controller, make sure to follow the
instructions in the ControlLogix Chassis and Power Supply
Installation Instructions, publication 1756-IN005.
When installing a ControlLogix controller, you can do the
following:
Place the controller in any slot. Use multiple controllers in
the same chassis.
You can install or remove a ControlLogix controller while
chassis power is on and the system is operating.
1. Align the circuit board with the top and bottom guides in the
chassis.
2. Slide the module into the chassis until it snaps into
place.
3. Verify that the controller is flush with the power supply or
other installed modules.ATTENTION: If you are using the controller
to the maximum
temperature of 60 C (140 F), you must use a Series C
chassis.
WARNING: When you insert or remove the module while backplane
power is on, an electrical arc can occur. This could cause an
explosion in hazardous location installations. Be sure that power
is removed or the area is nonhazardous before proceeding. Repeated
electrical arcing causes excessive wear to contacts on both the
module and its mating connector. Worn contacts may create
electrical resistance that can affect module operation.
32511-M
1
7
4
3
5
6
2
Item Description
1 4-character display
2 Status Indicators
3 Mode switch (Remote, Run, Program)
4 Ethernet Port
5 Ethernet Status Indicators
6 SD card slot and Reset Button are behind the door.
7 USB Port
Prevent Electrostatic Discharge
ATTENTION: This equipment is sensitive to electrostatic
discharge, which can cause internal damage and affect normal
operation.
Follow these guidelines when you handle this equipment:
Touch a grounded object to discharge potential static. Wear an
approved grounding wriststrap. Do not touch connectors or pins on
component boards. Do not touch circuit components inside the
equipment. Use a static-safe workstation, if available. Store the
equipment in appropriate static-safe packaging when
not in use.
325
Logix5585
REMRUN
PROG
!
0 0 0 0NET
LINK
RUN FORCE OKSD
Top Circuit Board Aligned
Bottom Circuit Board Aligned
Logix5585
REMRUN
PROG
!
0 0 0 0NET
LINK
RUN FORCE OKSD
6 Rockwell Automation Publication 1756-IN043A-EN-P - April
2016
http://literature.rockwellautomation.com/idc/groups/literature/documents/in/1756-in005_-en-p.pdf
-
ControlLogix 5580 Controllers
Install the SD Card
If the SD card is not already installed in the controller, then
complete these steps to install the SD card.
1. Verify that the SD card is locked or unlocked according to
your preference.
For more information about the lock/unlock memory settings, see
the ControlLogix 5580 Controllers User Manual, publication
1756-UM543.
2. Remove the key.
3. To access the SD card slot, open the door on the controller
key panel.
4. Position the SD card so that the contact end goes into the
controller, with the contacts on the right and the label on the
left. The beveled corner is on top.
5. Insert the SD card into the card slot and gently press the
card until it clicks into place.
6. The card slides in easily, if it is oriented correctly. You
can insert the card only one way.
7. Close the door.
8. Reinsert the key, if desired.
Connect to an EtherNet/IP Network
If you are connecting the controller directly to an EtherNet/IP
network, then connect an RJ45 cable to the Ethernet port on the
controller.
Confirm InstallationAfter you have inserted the controller into
the chassis and applied power, the 4-character display and status
indicators display status information for the controller. See the
ControlLogix 5580 Controllers User Manual, publication 1756-UM543,
for information on how to interpret the 4-character display
messages and the status indicators.
WARNING: When you insert or remove the CompactFlash/SD memory
card while power is on, an electrical arc can occur. This could
cause an explosion in hazardous location installations. Be sure
that power is removed or the area is nonhazardous before
proceeding.
Unlocked Locked
32005-M
Logix5585
REMRUN
PROG
!
0 0 0 0NET
LINK
RUN FORCE OKSD
SD Card
0 0 0 0
32531-M
2
1
SD Card
WARNING: If you connect or disconnect the communications cable
with power applied to this module or any device on the network, an
electrical arc can occur. This could cause an explosion in
hazardous location installations. Be sure that power is removed or
the area is nonhazardous before proceeding.
ATTENTION: 10 Mbps Ethernet automatic negotiations are
functional. However, 10 Mbps Ethernet connections are not fully
supported or intended for normal use. Use 10 Mbps Ethernet
connections only if necessary during temporary setup.
Logix5585
REMRUN
PROG
!
0 0 0 0NET
LINK
RUN FORCE OKSD
Rockwell Automation Publication 1756-IN043A-EN-P - April 2016
7
http://literature.rockwellautomation.com/idc/groups/literature/documents/um/1756-um543_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/1756-um543_-en-p.pdf
-
Specifications
Additional ResourcesThese documents contain additional
information concerning related products from Rockwell
Automation.
You can view or download publications at
http://www.rockwellautomation.com/global/literature-library/overview.page.
To order paper copies of technical documentation, contact your
local Allen-Bradley distributor or Rockwell Automation sales
representative.
Rockwell Automation SupportFor technical support, visit
http://www.rockwellautomation.com/support/overview.page.
Attribute 1756-L81E, 1756-L81EK, 1756-L82E, 1756-L82EK,
1756-L83E, 1756-L83EK, 1756-L84E, 1756-L84EK, 1756-L85E,
1756-L85EK
Temperature, operatingIEC 60068-2-1 (Test Ad, Operating
Cold),IEC 60068-2-2 (Test Bd, Operating Dry Heat),IEC 60068-2-14
(Test Nb, Operating Thermal Shock)
0 C < Ta < +60 C (+32 F < Ta < +140 F) for Series C
Chassis0 C < Ta < +50 C (+32 F < Ta < +122 F) for
Series B Chassis
Temperature, Surrounding Air, max 60 C (140 F) for Series C
Chassis50 C (122 F) for Series B Chassis
Enclosure type rating None (open-style)
Voltage and current ratings 1.20 A @ 5.1 V DC5.0 mA @ 1.2 V
DC
Isolation Voltage 50V (continuous), Basic Insulation type, USB
port to Backplane, Ethernet port to Backplane, and USB Port to
Ethernet port.Type tested at 1000V AC for 60 seconds
Weight, approx 394 g (0.868 lb)
Wire size Ethernet cabling and installation according to IEC
61918 and IEC 61784-5-2
North American Temp Code T4
ATEX Temp Code T4
IECEx Temp Code T4
Resource Description
1756 ControlLogix Controller Specifications Technical Data,
publication 1756-TD001 Provides controller specifications,
including communication options, memory use, compatibilities,
redundancy, and available accessories.
1756 ControlLogix Chassis Specifications Technical Data,
publication 1756-TD006 Provides chassis specifications, including
spacing requirements, mounting dimensions, and available
accessories.
ControlLogix 5580 Controllers User Manual, publication
1756-UM543 Provides complete information on how to install,
configure, select I/O modules, manage communication, develop
applications, and troubleshoot the ControlLogix 5580
controllers.
Replacement Guidelines: ControlLogix 5560/5570 Controller to
ControlLogix 5580 Reference Manual, publication 1756-RM100
Compares ControlLogix 5580 controllers to ControlLogix 5560/5570
controllers, and provides guidelines on the features, functions,
instruction updates, and differences between controllers.
ControlLogix Chassis and Power Supply Installation Instructions,
publication 1756-IN005 Provides complete information on how to plan
the power system, install, and troubleshoot the ControlLogix
chassis and power supply.
Industrial Automation Wiring and Grounding Guidelines,
publication 1770-4.1 Provides general guidelines for installing a
Rockwell Automation industrial system.
Product Certifications
website,http://www.rockwellautomation.com/global/certification/overview.page
Provides declarations of conformity, certificates, and other
certification details.
Allen-Bradley, ControlLogix, FactoryTalk, Rockwell Automation,
Rockwell Software, and Studio 5000 Automation Engineering &
Design Environment are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of
their respective companies.
Rockwell Otomasyon Ticaret A.., Kar Plaza Merkezi E Blok Kat:6
34752 erenky, stanbul, Tel: +90 (216) 5698400
Rockwell Automation maintains current product environmental
information on its website
athttp://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.
Publication 1756-IN043A-EN-P - April 2016 PN-348025Supersedes
Publication 1756-PC405B-EN-P - October 2015 Copyright 2016 Rockwell
Automation, Inc. All rights reserved. Printed in the U.S.A.
http://literature.rockwellautomation.com/idc/groups/literature/documents/td/1756-td001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/td/1756-td006_-en-e.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/1756-um543_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/rm/1756-rm100_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/in/1756-in005_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdfhttp://www.rockwellautomation.com/global/certification/overview.pagehttp://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.pagehttp://www.rockwellautomation.com/global/literature-library/overview.page
ControlLogix 5580 Controllers Installation InstructionsParts
ListRequired System ComponentsProduct DimensionsConnectors and
Status IndicatorsInstall the ControllerInstall the SD CardConnect
to an EtherNet/IP NetworkConfirm
InstallationSpecificationsAdditional Resources
Back Cover
Introduction_Category Types
This tab summarizes Rockwell Automation Global Sales and
Marketing preferred printing standards. It also provides guidance
on whether a publication should be released as JIT (print on
demand) or if it requires an RFQ for offset printing.Find your
publication type in the first section below. Use the assigned
Printing Category information to determine the standard print
specifications for that document type. The Printing Categories are
defined below the Publication Type section. Note there may be
slightly different print specifications for the categories,
depending on the region (EMEA or Americas).For more information on
Global Sales and Marketing Printing Standards, see publication
RA-CO004 in DocMan.
Publication Type and Print Category
Publication TypeOff Set Print Category Spec. (See table
below)JIT Spec. (See table below)DescriptionOrder Min **Order Max
**Life Cycle Usage / Release Option
ADNA - PuttmanNAAdvertisement Reprint ColourNANAPresale /
Internal
APA3D2Application Solution or Customer Success Story5100Presale
/ External
ARNANAArticle/Editorial/BylineNANAPresale / Internal
(press releases should not be checked into DocMan or
printed)
ATB3, B4D5Application techniques5100Presale / External
BRA2 Primary, A1NABrochures5100Presale / External
CAC2 Primary, C1NACatalogue150Presale / External
CGNANACatalogue Guide150Presale / External
CLNANACollection550Presale / External
COA5, A6, A9D5Company Confidential InformationNANANA /
Confidential
CPE-onlyE-only, D5Competitive Information550NA /
Confidential
DCE-onlyE-onlyDiscount SchedulesNANAPresale / Internal
DIA1, A3NADirect Mail5100Presale / Internal
DMNANAProduct Demo550Presale / Internal
DSB3D5Dimensions Sheet15Post / External
DUB3D5Document Update15Post / External
GRB2D6Getting Results15Post / External
INB3 Primary, B2D5, D6Installation instructions15Post /
External
LMNANALaunch Materials550Presale / Internal
PCB3D5Packaging Contents
PLE-only primary, B3E-onlyPrice List550Presale / Internal
PMB2D6Programming Manual15Post / External
PPA3D1Profile (Single Product or Service). NOTE: Application
Solutions are to be assigned the AP pub type.5100Presale /
External
QRB2 primary, B3, B5D5, D6Quick Reference15Post / External
QSB2 primary, B3, B5D5, D6Quick Start15Post / External
RMB2D5, D6Reference Manual15Post / External
RNB3D5Release Notes15Post / External
SGB1 Primary, B4D5, D6Selection Guide Colour550Presale /
External
SGB2D5, D6Selection Guide B/W550Presale / External
SPA1, A2, A3, A4NASales Promotion NOTE: Service profiles are to
be assigned the PP pub type.5100Presale / Internal
SRB2, B3D5, D6Specification Rating Sheet5100Presale /
External
TDB2 Primary B3, B4, B5D5, D6Technical Data550Presale /
External
TGB2, B3D6Troubleshooting Guide15Post / External
UMB2 Primary, B4D6User Manual B/W15Post / External
WDB3D5Wiring Diagrams / Dwgs15Post / Internal
WPB3 Primary, B5D5White Paper550Presale / External
** Minimum order quantities on all JIT items are based on the
publication length. **
Publication lengthMinimum Order Quantity
77 or more pages1 (no shrink wrap required)
33 to 76 pages25
3 to 32 pages50
1 or 2 pages100
Pre-sale / MarketingAll paper in this category is White
Brightness, 90% or better. Opacity 90% or better
CategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US
Paper Requirements
A14 color170 gsm 2pp100# gloss cover, 100# gloss text
A24 color170 gsm , folded, 4pp100# gloss cover, 80# gloss
text
A34 colorCover 170 gsm with Body 120 gsm, > 4pp80# gloss
cover, 80# gloss text
A42 color170gsm Silk 120gsm Silk80# gloss cover, 80# gloss
text
A52 color170gsm Silk 120gsm Silk80# gloss cover, 80# matt sheet
text
A61 color170gsm Silk 120gsm Silk80# gloss cover, 80# matt sheet
text
A74 color cover2 color textSelection GuideCategory being
deleted10 Point Cover C2S50# matte sheet text
A84 color coverCategory being deleted50# matte sheet text, self
cover
2 color text
Selection Guide
A92 color100gsm bond50# matte sheet text, self cover
Selection Guide
Gray shading indicates Obsolete Print Catagories
Post Sale / Technical Communication
CategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US
Paper Requirements
B14 color cover270gsm Gloss 100gsm bond10 Point Cover C2S
2 color text50# matte sheet text
B21 color160gsm Colortech & 100gsm Bond90# Cover50# matte
sheet text
B31 color100gsm bond50# matte sheet text, self cover
B42 color160gsm Colortech & 100gsm Bond90# Cover50# matte
sheet text
B52 color100gsm bond50# matte sheet text, self cover
Catalogs
CategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US
Paper Requirements
C14 color cover270gsm Gloss 90gsm silk10 Point Cover C2S
4 color text45# Coated Sheet
C24 color cover270gsm Gloss 80gsm silk10 Point Cover C2S
2 color text32#-33# Coated Sheet
JIT / PODAll paper in this category is White Brightness, 82% or
better. Opacity 88% or better
CategoryColor OptionsAP, EMEA Paper RequirementsCanada, LA, US
Paper Requirements
D14 color170gsm white silk80# gloss cover, coated 2 sides
D24 color120gsm white silk80# gloss text, coated 2 sides, self
cover
D34 colorCover 170gsm with Body 120gsm80# gloss cover, 80# gloss
text coated 2 sides
D41 color160gsm tab90# index
D51 color80gsm bond20# bond, self cover
D61 colorCover 160gsm tab with Body 80gsm bond90# index, 20#
bond
D72 color160gsm tab90# index
D82 color80gsm bond20# bond, self cover
D92 colorCover 160gsm tab with Body 80gsm bond90# index, 20#
bond
D10Combination: 4 color cover, with 2 color bodyCover 160gsm
with Body 80gsm90# index, 20# bond
Gray shading indicates Obsolete Print Catagories
Just In Time (JIT) or Off Set (OS)?
Use these guidelines to determine if your publication should be
JIT (just in time/print on demand) or if it would be more
economical to print OS (offset/on a press). OS print jobs require
an RFQ (Request For Quote) in US. If your job fits into the Either
category, an RFQ is recommended, but not required. In the US, RA
Strategic Sourcing will discourage or reject RFQs for jobs that
fall within the JIT category. Guidelines differ for black &
white and color printing, so be sure to check the correct
tables.
Black & White Printing
Color Printing
Color Printing
Print Spec Sheet
JIT Printing SpecificationsRA-QR005J-EN-P - 6/14/2013
Printing SpecificationYOUR DATA HEREInstructionsNO
(required) Publication Number:1756-IN043A-EN-PSample:
2030-SP001B-EN-P11 x 17LOOSE -Loose LeafYESPre-sale /
MarketingTOP
Use Legacy Number:YES or NO8.5 x 11PERFECT - Perfect
BoundA1LEFT
Legacy Number if applicable:Sample Legacy Number: 0160-5.338.375
x 10.875SADDLE - Saddle StitchA2RIGHTCORNER
Publication Title:ControlLogix 5580 Controllers Installation
InstructionsSample: ElectroGuard Selling Brief80 character limit -
must match DocMan Title8.25 x 11 (RA product profile std)PLASTCOIL
- Plastic Coil (Coil Bound)A4BOTTOMSIDE
Used in Manufacturing:YESYES or NO - If Yes, must have Part No.
listed below8.25 x 10.875STAPLED1 -1 positionA3
Part Number:PN-348025If SAP Part Number, be sure to enter PN-
before the number7.385 x 9 (RSI Std)STAPLED1B - bottom 1
positionA5
(required) CategoryD5Select Print Category A,B,C or D from
category list, on "Introduction_Category Types" tab6 x 4STAPLED2 -
2 positionsA6
Paper Stock Color:WhiteWhite is assumed. For color options
contact your vendor5.5 x 8.5 (half-size)THERMAL - Thermal bound
(Tape bound)A7
Ink Color:BlackOne color assumes BLACK / 4 color assume CMYK /
Indicate PMS number here4.75 x 7.75THERMALO - Thermal Bound (Tape
bound - offline)A8
(required) Page Count ofPublication:8Total page count including
cover. Enter PAGE count, not SHEET count4.75 x 7 (slightly smaller
half-size)A9
(required) Finished Trim Size Width:8.5 x 11This is sheet size,
before folding4.25" x 5.50"Post Sale / Technical Communication
Fold:Microfold or French Fold - designate no. of folds in
Comments - intended for single sheet only to be put in box for
manufacturingReview key below. Leave blank if folded for saddle
stitching4 x 6B1
Finished Fold Size:4.25" x 5.50"This is size after folding is
completed3 x 5B2
Binding/Stitching:STAPLED1 -1 positionReview key below9 x 12
(Folder)B3None
Stitching Location:CORNERBlank, Corner or SideA4 (8 x 11 ) (210
x 297 mm)B4Half or V or Single Fold
Drill Hole (Yes/No):NOAll drilled publications use the 5-hole
standard, 5/16 inch-size hole and a minimum of inch from the inner
page border.A5 (5.83 x 8.26) (148 x 210 mm)B5C or Tri-Fold
Number of Tabs Needed:5 tab in stock at RR Donnelley36 x 24
PosterCatalogsDbleParll
Number of Pages per Pad:Average sheets of paper. 25, 50 75,100
Max24 x 36 PosterC1Sample
Glue Location on Pad:Glue location on pads18 x 24 PosterC2Short
(must specify dimensions between folds in Comments)
(required) Business Group:Marketing CommercialAs entered in
DocManJIT/PODZ or Accordian Fold
(required) Cost Center:19134 - IAIf your Business Unit is
Marketing Commercial, add the appropriate division name after 19134
using the chart on the right. All other Business Units: Enter only
the number as in DocMan, no description. Example - 1902119134 -
Commerc 19134 - OEM 19134 - Compone 19134 - Power C19134 - Global
19134 - Process 19134 - IA 19134 - Service 19134 - IMC 19134 -
Safety 19134 - Industr 19134 - Softwar19134 - Mkt Dig 19134 - US
MarkeD1Microfold or French Fold - designate no. of folds in
Comments - intended for single sheet only to be put in box for
manufacturing
Comments:Fold in quarters (2 folds) so that part number is
visible on top.D2Double Gate
FoldsHalf, V, Single C or Tri
Dble Parll
Z or Accordian Microfold or French
Double Gate
Short FoldSaddle-Stitch Items All page quantities must be
divisible by 4.Note: Stitching is implied for Saddle-Stitch -no
need to specify in Stitching Location.80 pgs max. on 20# (text and
cover)76 pgs max. on 20# (text) and 24# (cover)72 pgs max. on 24#
(text and cover)
Perfect Bound Items940 pgs max. w/cover (90# index unless
indicated otherwise)70 pgs. min. for spine without words200 pgs
min. for spine with words
Plastcoil Bound Items530 pgs max. of 20# (if adding cover deduct
equivalent number of pages to equal cover thickness) (90# index
unless indicated otherwise)
Tape Bound Items250 pgs max. on 20# no cover240 pgs max. w/cover
(90# index unless indicated otherwise)D3
D4
D5
D6
D7
D8
D9
MBD000B0209.bin
MBD000B020B.bin
MBD000B020C.bin
MBD000B020A.bin
MBD000B0205.bin
MBD000B0207.bin
MBD000B0208.bin
MBD000B0206.bin
MBD000B0203.bin
MBD000B0204.bin
/ColorImageDict > /JPEG2000ColorACSImageDict >
/JPEG2000ColorImageDict > /AntiAliasGrayImages false
/CropGrayImages true /GrayImageMinResolution 300
/GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true
/GrayImageDownsampleType /Average /GrayImageResolution 300
/GrayImageDepth -1 /GrayImageMinDownsampleDepth 2
/GrayImageDownsampleThreshold 2.00000 /EncodeGrayImages true
/GrayImageFilter /DCTEncode /AutoFilterGrayImages false
/GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict >
/GrayImageDict > /JPEG2000GrayACSImageDict >
/JPEG2000GrayImageDict > /AntiAliasMonoImages false
/CropMonoImages true /MonoImageMinResolution 1200
/MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true
/MonoImageDownsampleType /Average /MonoImageResolution 1200
/MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000
/EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode
/MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None
] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false
/PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000
0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true
/PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ]
/PDFXOutputIntentProfile (None) /PDFXOutputConditionIdentifier ()
/PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped
/False
/CreateJDFFile false /Description > /Namespace [ (Adobe)
(Common) (1.0) ] /OtherNamespaces [ > /FormElements false
/GenerateStructure true /IncludeBookmarks false /IncludeHyperlinks
false /IncludeInteractive false /IncludeLayers false
/IncludeProfiles true /MultimediaHandling /UseObjectSettings
/Namespace [ (Adobe) (CreativeSuite) (2.0) ]
/PDFXOutputIntentProfileSelector /NA /PreserveEditing true
/UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling
/LeaveUntagged /UseDocumentBleed false >> ]>>
setdistillerparams> setpagedevice