• Prepare the the ground around all sides 500mm larger in size than the terrace deck and with a 4% gradient. • Create a weight-bearing and frostproof with a 2% incline and screed with fine gravel (level out any unevenness). • Do not fill in any cavities between the construction beam, the concrete edge stone and the base of the Fix SteP • Avoid soil contact! (exception: items from the construction plank range)! • Lay the substructure system in accordance with the construction plan! • Differences in the floorboards are intended and underline the natural wood look. • Mix the floorboards before laying them in order to support the effect. • Observe the laying direction (refer to the arrow in the floorboard groove or on the label)! • Do not exceed the max. 50 mm floorboard protrusion over the sub-structure! • Assembly and production-related dimension tolerances regarding the length, width and thickness are to be taken into account and checked! • Cutting the longitudinal side of the floorboards may result in floorboard offset. Publisher: NOVO-teCH trading GmbH & Co. KG, Siemensstraße 31, 06449 Aschersleben, Germany Conception/design/layout: toolboxx-media, Magdeburg, Germany Picture credits: Christian Wolf, Aschersleben, Germany Subject to change. Colours and graphics may differ due to printing processes. • the megawood construction plan forms the basis for all of the laying variations! No warranty is provided in the event of deviations being made from the construction plan or should items be used other than original megawood items! • Lay the terrace floorboards in a longitudinal direction with an adequate gradient in order to ensure that water is always able to drain off from the deck, this conforms with the principles of structural wood preservation. the risk of water stains, waterlogging and build up of organic substances is reduced by adhering to this. • Applications that require building approval are to be provided with a statically sufficiently dimensioned, supporting and fall-through proof sub-structure as a support for megawood barefootboards or substructures/construction planks. • A min. gradient of 2% is recommended for deck superstructures with an open gap. A min. gradient of 2% is absolutely necessary for deck superstructures with a closed gap. • ensure sufficient ventilation from beneath and the rear, e.g. with the megawood ventilation grid. • Avoid waterlogging by using a drainage system that is adequately dimensioned! • ensure an unrestrained expansion of the terrace deck (min. distance of 20 mm between the floorboards and solid components)! • Always pre-drill all holes so that the part that is to be fixed is 2 mm larger than the screw diameter and the retaining drill hole is 0.5 mm smaller than the screw diameter! • All dimensions are to be checked on site • Coordination with the manufacturer must take place and respective approval must be obtained in the event of special structures that deviate from this construction plan or the online planner in order for any potential warranty claims to be accepted. • the thermal characteristics of the material that the corresponding article is made of is to be taken into account (recommended laying temperature 5°-25°C) when using the P5 joint profile. • When building the terrace, the wind load must be taken into con sideration as a liſting load in the construction. You should cover your terrace in shade when it is exposed to intense sunlight during hot summer temperatures. this particularly protects the sensitive feet of children against hot surfaces. in addition it prevents skin damage caused by excessive UV rays. A conscious effort in terms of protec- ting against the severe impacts of the Sun ensures a carefree barefoot experience. this basic construction plan explains the standard structure versions for rectangular decks when laying in the longitudinal direction. Special styles, mitre cuts, braces and diagonal laying are illustrated individually in our “megaplaner“. L: 360 cm LAVA BROWN BASALt GReY NAtURAL BROWN NUt BROWN SLAte GReY iNGWeR SeL GRiS LORBeeR Ø 34 mm (0.25 W, 10 lm) Ø 60 mm (0.5 W, 28 lm) 24 V DC iP67 Stainless steel H: 21 mm; B: 62 mm L: 3,600 mm (27 W, 729 lm) 4,800 mm (36 W, 972 lm) 6,000 mm (45 W, 1215 lm) 27 lm/W; 24 V DC iP65 Aluminium/plastic install lamps at a max. distance of 50 mm from a construction beam. Lay an additional beam if necessary. Note: the lights are equipped with LeD lamps from energy classes A++ to A. the lamps installed in the lights cannot be replaced. Further information regarding the installation of megalite LeD spotlights can be found here: L: 220 | 270 cm L: 178,6 cm L: 160,2 | 210 cm L: 158,4 | 210 cm L: 156,6 | 178,6 190 cm Up to 10 % incline without diagonal cut to the panel 40 x 112 mm | L: 360 cm 40 x 145 mm | L: 420 cm 20.5 x 81 mm | L: 420 cm Attractive wood cladding can be obtained using the new rhombus profile. it is also possible to screw it on visibly or you can also use a clip so that it is concealed. VARiA GReY VARiA CHOCOLAte BLACK You will find the entire item summary for the Limes fencing system here: 90 x 90 mm | L: 360 cm 40 x 60 mm | L: 360 cm 7,5 x 92 mm, incl. tx 30 and SDS drill (Ø 6.5 mm) 7,5 x 132 mm, incl. tx 30 and SDS drill (Ø 6.5 mm) for construction beams 28x76mm L: 360 cm (on a roll) 21 mm | L: 25/100 m for closed gap for (CLASSiC, PReMiUM, PReMiUM PLUS) without groove strip 21 mm | L: 400 cm silver/bronze/anthracite 55 x 8 x 10 mm, for fastening the locking clamp on a construction beam gap for construction beams 28 x 76 mm | L: 360 cm 60 x 100 mm thickness: 3/10 /20 mm 21 mm | L: 400 cm silver/bronze/anthracite 280 x 260 x71 mm 250x60x55mm 270 x 180 x 71 mm 116x60x55mm 78x40x20mm 40 x 60 mm | L: 360 cm for smooth edge board, complete with nut and washer 79x58x83mm for footstep cushioning with groove strip/P5 gap profile – raised construction ensures the required ventilation assembly aid for setting the floorboard gaps (approx. 5 mm/ approx. 8 mm) L: 10 m (on a roll), self-adhesive for smooth edge board, complete with nut and washer assembly aid for setting the floorboard gaps (approx. 5 mm/ approx. 8 mm) 21 x 242 mm L: 360/420/480/540/600 cm 25x293mm L: 360/420/480/540/600 cm 17 x 72 mm | L: 360 cm 21x145mm L: 300/360/420/480/540/600 cm 21 x 242 mm (Jumbo) L: 420/480/600 cm 293 mm 5 mm 17 x 72 mm | L: 360 cm 21x145mm L: 300/360/420/480/540/600 cm 21 x 242 mm (Jumbo) L: 300/360/420/480/540/600 cm 17 x 72 mm | L: 360 cm 55 x 8 x 10 mm, for fastening the locking clamp on a construction beam gap L: 10 m (self-adhesive) for perforated tape, complete with nut and washer 4 x 35 mm L: 10 m (on a roll) 300 x 300 mm, thickness: 3/5/10 mm and incl. screws (4 x 35 mm), Bit tx 20 (on a roll) 21 mm | L: 25/100 m for closed gap (CLASSiC, PReMiUM, PReMiUM PLUS) Combination floorboard, finely corrugated on one side, grooved and brushed surface on the other, 8 mm gap Single-sided, textured, polished surface with colour gradient, 5 mm gap Oscillating planed surface, brushed underside, 8 mm gap textured on one side, oscillating brushed, polished surface, 5 mm gap 21x145mm L: 300/360/420/480/540/600 cm 21 x 242 mm (Jumbo) L: 420/480/600 cm 17 x 72 mm | L: 360 cm Oscillating planed surface, brushed underside, 8 mm gap 17 x 72 mm | L: 360 cm NUt BROWN NAtURAL BROWN BASALt GReY LAVA BROWN SLAte GReY NUt BROWN NAtURAL BROWN BASALt GReY LAVA BROWN SLAte GReY MUSKAt tONKA CARDAMOM NiGeLLA VARiA BROWN VARiA GReY VARiA CHOCOLAte BLACK MUSKAt tONKA NAtURAL BROWN NUt BROWN BASALt GReY LAVA BROWN SLAte GReY NiGeLLA CARDAMOM with groove strip/P5 gap profile – only with a raised superstructure using a 90 x 90 mm construction beam without groove strip/P5 gap profile 242 mm 242 mm 5 mm 145 mm 145 mm 5 mm 5 mm 145 mm ±0,5 mm ±0,5 mm ±0,5 mm ±0,5 mm 21x145mm L: 300/360/420/480/540/600 cm 21 x 242 mm (Jumbo) L: 300/360/420/480/540/600 cm 145 mm 145 mm 8 mm 8 mm 145 mm 242 mm 242 mm 8 mm ±0,5 mm ±0,5 mm ±0,5 mm 242 mm 242 mm 8 mm 145 mm 145 mm 8 mm 8 mm 145 mm ±0,5 mm ±0,5 mm ±0,5 mm 242 mm 242 mm 145 mm 145 mm 8 mm 8 mm 145 mm 8 mm ±0,5 mm ±0,5 mm ±0,5 mm and for the lock clip fastening 293 mm 242 mm 242 mm 5 mm ±0,5 mm for the lock clip fastening and incl. screws (4 x 35 mm), Bit tx 20 21x195mm L: 420/480/600 cm 17 x 72 mm | L: 360 cm Partially-grooved surface on one side with colour gradient, 5 mm gap VARiA CHOCOLAte BLACK VARiA BROWN VARiA GReY 195 mm 195 mm 5 mm 5 mm 195 mm ±0,5 mm ±0,5 mm On a roll, for closed CLASSiC longitudinal gap (Varia) Zammer attachment for the retraction of the joint profile and incl. screws (4 x 35 mm), Bit tx 20 and and incl. screws (4 x 35 mm), Bit tx 20 On a roll, for closed CLASSiC longitudinal gap (Varia) Spacer for front-end joints (when laying in a pattern) Spacer for front-end joints (when laying in a pattern) m You shall find examples of use and the assembly instructions for locking clamp and the clip at: terrace system
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Planning principlesPreparation and sub-construction
• Preparethethegroundaroundallsides500mmlarger insizethantheterracedeckandwitha4%gradient.
• Createaweight-bearingandfrostproofgravel or crushed rock bedwitha2%inclineandscreedwithfinegravel (leveloutanyunevenness).
• Donotfillinanycavitiesbetweentheconstructionbeam, theconcreteedgestoneandthebaseoftheFixSteP!
• Avoidsoilcontact!(exception:itemsfromtheconstruction plankrange)!
• Laythesubstructuresysteminaccordancewiththeconstruction plan!
Floorboard assembly• Differencesinthefloorboardsareintendedandunderline thenaturalwoodlook.
• Mixthefloorboardsbeforelayingtheminordertosupport theeffect.
• Observethelayingdirection(refertothearrowinthe floorboardgrooveoronthelabel)!
• Donotexceedthemax.50mmfloorboardprotrusionover thesub-structure!
• Assemblyandproduction-relateddimensiontolerances regardingthelength,widthandthicknessaretobetaken intoaccountandchecked!
• Cuttingthelongitudinalsideofthefloorboardsmayresult infloorboardoffset.
W W W . M E G A W O O D . C O M
IMPRINTPublisher:NOVO-teCHtradingGmbH&Co.KG,
Siemensstraße31,06449Aschersleben,Germany
Conception/design/layout:toolboxx-media,Magdeburg,Germany
Picturecredits:ChristianWolf,Aschersleben,Germany
Subjecttochange.Coloursandgraphicsmaydifferdue
toprintingprocesses.
Date: 1. edition 2020 EN / 31.01.2020
YOUR SUPPLIER
• themegawood®constructionplanformsthebasisforallofthe layingvariations!Nowarrantyisprovidedintheeventofdeviations beingmadefromtheconstructionplanorshoulditemsbeused otherthanoriginalmegawood®items!
• Laytheterracefloorboardsinalongitudinaldirectionwithan adequategradientinordertoensurethatwaterisalwaysable todrainofffromthedeck,thisconformswiththeprinciples ofstructuralwoodpreservation.theriskofwaterstains, waterloggingandbuildupoforganicsubstancesisreducedby adheringtothis.
• Applicationsthatrequirebuildingapprovalaretobeprovidedwith astaticallysufficientlydimensioned,supportingandfall-through proofsub-structureasasupportformegawood®barefootboards orsubstructures/constructionplanks.
• Amin.gradientof2%isrecommendedfordecksuperstructures withanopengap.Amin.gradientof2%isabsolutelynecessary fordecksuperstructureswithaclosedgap.
• ensuresufficientventilationfrombeneathandtherear,e.g. withthemegawood®ventilationgrid.
• Avoidwaterloggingbyusingadrainagesystemthatis adequatelydimensioned!
• ensureanunrestrainedexpansionoftheterracedeck(min. distanceof20mmbetweenthefloorboardsandsolidcomponents)!
• Alwayspre-drillallholessothatthepartthatistobefixedis 2mmlargerthanthescrewdiameterandtheretainingdrill holeis0.5mmsmallerthanthescrewdiameter!
• Alldimensionsaretobecheckedonsite
• Coordinationwiththemanufacturermusttakeplaceand respectiveapprovalmustbeobtainedintheeventofspecial structuresthatdeviatefromthisconstructionplanorthe onlineplannerinorderforanypotentialwarrantyclaimstobe accepted.
• thethermalcharacteristicsofthematerialthatthecorresponding articleismadeofistobetakenintoaccount(recommended layingtemperature5°-25°C)whenusingtheP5jointprofile.• Whenbuildingtheterrace,thewindloadmustbetakenintocon siderationasaliftingloadintheconstruction.
General information
Youshouldcoveryourterraceinshadewhenitisexposedtointense
sunlightduringhotsummertemperatures.thisparticularlyprotectsthe
sensitivefeetofchildrenagainsthotsurfaces.inadditionitpreventsskin
damagecausedbyexcessiveUVrays.Aconsciouseffortintermsofprotec-
tingagainstthesevereimpactsoftheSunensuresacarefreebarefoot
experience.
Online Plannerthisbasicconstructionplanexplainsthestandardstructureversionsforrectangulardeckswhenlayinginthelongitudinaldirection.Specialstyles,mitrecuts,bracesanddiagonallayingareillustratedindividuallyinour“megaplaner“.www.megawood.com/108
NEW
CONSTRUCTION WOOD ROUND | SQUARE | OCTAGONAL | OVALØ 90 mm | 90 x 90 mm | 90 x 90 mm | 90 x 60 mmL:360 cm
CONSTRUCTION WOOD
ROUND | SQUARE | OCTAGONAL | OVAmm | 90x90mm | 90x60mm
L: 360cm
| OVAL | OVALmm
LAVABROWN
BASALtGReY
NAtURALBROWN
NUtBROWN SLAteGReY
iNGWeR
SeLGRiS
LORBeeR
megalite LIGHT SYSTEM
LED SPOT MINI/MAXIØ34 mm(0.25 W,10 lm)Ø60 mm(0.5 W,28 lm)24VDCiP67Stainlesssteel
LED LINEAR LIGHTSH:21 mm;B:62 mmL:3,600 mm(27 W,729 lm)4,800 mm(36 W,972 lm)6,000 mm(45 W,1215 lm)27 lm/W;24VDCiP65Aluminium/plastic
installlampsatamax.distanceof50mmfromaconstructionbeam.Layanadditionalbeamifnecessary.Note:thelightsareequippedwithLeDlampsfromenergyclassesA++toA.thelampsinstalledinthelightscannotbereplaced.
FurtherinformationregardingtheinstallationofmegaliteLeDspotlightscanbefoundhere:www.megawood.com/121
lm)lm)
1215lm)
mm (0.25W, 10 lm)mm (0.5W, 28DCiP67
Stainless steel
H:L:27Aluminium/plastic
10 lm)28 lm)
POSTSROUND | SQUARE | OCTAGONAL | OVALØ 90 mm | 90 x 90 mm | 90 x 90 mm | 90 x 60 mmL:220|270 cm
TRANSOM40 x 112 mm90 x 60 mmL:178,6 cm
LIMES FENCING SYSTEM
PANEL AUGUSTA (wavy)270 x 35 mmL:160,2|210 cm
PANEL COLONIA (smooth)239 x 6 mmL:158,4|210 cm
CONNECTING SPACER38 x 30 mmL:156,6|178,6190 cm
FENCE SETSTAINLESS STEEL BARPanel Augusta (wavy)Upto10 %inclinewithoutdiagonalcuttothepanel
CONSTRUCTION PLANK 40 x 112 mm|L:360 cm40 x 145 mm|L:420 cm
RHOMBUS PROFILE 20.5 x 81 mm|L:420 cm
Attractivewoodcladdingcanbeobtainedusingthenewrhombusprofile.itisalsopossibletoscrewitonvisiblyoryoucanalsouseaclipsothatitisconcealed.
VARiAGReY VARiACHOCOLAteBLACK
YouwillfindtheentireitemsummaryfortheLimesfencingsystemhere:www.megawood.com/129
min
. 17
1 m
m
min
. 121
mm
Locking clamp
Screw (7.5 x 132 mm, pre-drill!)
Construction beams (90 x 90 mm)
Rubber pad (10 x 100 x 60 mm)for height compensation measuring 3/10/20 mm in thickness
Concrete edge stone (50 x 1000 x 250 mm) (available from building material dealers)
93
mm
104
mm
116
mm
127
mm
139
mm
143
mm
154
mm
166
mm
177
mm
189
mm
Construction beams (40 x 60 mm)
Standard mounting
Standard panel
Construction beams (40 x 60 mm)
Attachment
Comfort pad
Standard mounting
Standard panel
Two construction beams (40 x 60 mm)
Two attachments
Two comfort pads
DUO mounting DUO edge panel
CONSTRUCTION BEAMS90x90mm|L:360cm
CONSTRUCTION BEAMS40x60mm|L:360cm
SUB-CONSTRUCTION SCREW 40/607,5x92mm,incl.tx30andSDSdrill(Ø6.5mm)
SUB-CONSTRUCTION SCREW 90/907,5x132mm,incl.tx30andSDSdrill(Ø6.5mm)
CONNECTING CLIP forconstructionbeams28x 76 mmL:360 cm
GROOVE STRIP (onaroll)21mm|L:25/100mforclosedgapfor(CLASSiC,PReMiUM,PReMiUMPLUS)
Open gapwithoutgroovestrip
FIX STEP basis sub-structure
HOUSE CONNECTION PROFILE 21mm|L:400cmsilver/bronze/anthracite
Basis concrete edge stone sub-structure
GROOVE BRIDGE 55x8x10mm,forfasteningthelockingclamponaconstructionbeamgap
CONNECTING CLIP forconstructionbeams28x76mm|L:360cm
RUBBER PAD60x100mmthickness:3/10/20mm
HOUSE CONNECTION PROFILE 21mm|L:400cmsilver/bronze/anthracite
FIX STEP DUO EDGE PANEL280x260x71 mm
FIX STEP DUO EDGE MOUNTING250x60x55 mm
FIX STEP STANDARD PANEL270x 180x71 mm
FIX STEP STANDARD MOUNTING116x60x55 mm
ASSEMBLY CLIP78x40x20 mm
CONSTRUCTION BEAMS40x60 mm|L:360 cm
FASTENING SCREW M8 x80 forsmoothedgeboard,completewithnutandwasher
FIX STEP ATTACHMENT79x58x83mm
FIX STEP COMFORT PAD forfootstepcushioning
FIX STEP comfort sub-structure (raised)
Closed gapwithgroovestrip/P5gapprofile–raisedconstructionensurestherequiredventilation
Raised concrete edge stone sub-structure
SPACERassemblyaidforsettingthefloorboardgaps(approx.5mm/approx.8mm)
RETAINING BANDL:10m(onaroll),self-adhesive
FASTENING SCREW M8 x80 forsmoothedgeboard,completewithnutandwasher
SPACERassemblyaidforsettingthefloorboardgaps(approx.5mm/approx.8mm)
Groove strip with clip
Construction variants Installation heights Article overview Supplementary products
Deck coveringPREMIUM PLUS
BAREFOOTBOARD21 x 242mm
L:360/420/480/540/600 cm
25 x 293 mm
L:360/420/480/540/600 cm
CLASSIC
SMOOTH EDGE BOARD17 x 72mm|L:360 cm
SIGNUM
BAREFOOTBOARD 21 x 145 mm
L:300/360/420/480/540/600 cm
21 x 242mm(Jumbo)
L:420/480/600 cm
293 mm 5 mm
DYNUM
SMOOTH EDGE BOARD17 x 72mm|L:360 cm
BAREFOOTBOARD 21 x 145 mm
L:300/360/420/480/540/600 cm
21 x 242 mm(Jumbo)
L:300/360/420/480/540/600 cm
SMOOTH EDGE BOARD17 x 72mm|L:360 cm
GROOVE BRIDGE 55x8x10mm,forfasteningthelockingclamponaconstructionbeamgap
RETAINING BANDL:10m(self-adhesive)
M6 x 16 FASTENING SCREW forperforatedtape,completewithnutandwasher
SCREW SET4x35mm
FIX STEP PERFORATED TAPEL:10m(onaroll)
FIX STEP RUBBER PAD 300x300mm,thickness:3/5/10mm
SECURING CLAMP andEDGE CLAMPincl.screws(4 x 35 mm),Bittx20
GROOVE STRIP (onaroll)21mm|L:25/100mforclosedgap(CLASSiC,PReMiUM,PReMiUMPLUS)
Combinationfloorboard,finelycorrugatedononeside,groovedandbrushedsurfaceontheother,8mmgap
Single-sided,textured,polishedsurfacewithcolourgradient,5mmgap
Oscillatingplanedsurface,brushedunderside,8mmgap texturedononeside,oscillatingbrushed,polishedsurface,5mmgap
PREMIUM
BAREFOOTBOARD21 x 145 mm
L:300/360/420/480/540/600 cm
21 x 242 mm(Jumbo)
L:420/480/600 cm
SMOOTH EDGE BOARD17 x 72 mm|L:360 cm
Oscillatingplanedsurface,brushedunderside,8mmgap
Connecting clip
SMOOTH EDGE BOARD17 x 72mm|L:360 cm
COLOURSNUtBROWN
NAtURALBROWN
BASALtGReY
LAVABROWN
SLAteGReY
NUtBROWN NAtURALBROWN BASALtGReY LAVABROWN SLAteGReY MUSKAt tONKA CARDAMOM NiGeLLA VARiABROWN VARiAGReY VARiACHOCOLAteBLACK
COLOURSMUSKAt
tONKA
COLOURSNAtURALBROWN
NUtBROWN
BASALtGReY
COLOURSLAVABROWN
SLAteGReY
COLOURSNiGeLLA
CARDAMOM
320 mm
70 mm
10 mm gap
10 mm gap
Closed gap withgroovestrip/P5gapprofile–onlywitharaisedsuperstructureusinga90x90mmconstructionbeam
Open gap withoutgroovestrip/P5gapprofile
Standard panel Edge panel
Standard panel Edge panel
242 mm 242 mm5 mm
145 mm 145 mm 5 mm5 mm 145 mm±0,5mm ±0,5mm
±0,5mm ±0,5mm
BAREFOOTBOARD21 x 145 mm
L:300/360/420/480/540/600 cm
21 x 242 mm(Jumbo)
L:300/360/420/480/540/600cm
145 mm 145 mm 8 mm8 mm 145 mm
242 mm 242 mm8 mm
±0,5mm ±0,5mm
±0,5mm242 mm 242 mm8 mm
145 mm 145 mm 8 mm8 mm 145 mm±0,5mm ±0,5mm
±0,5mm
242 mm 242 mm
145 mm 145 mm 8 mm8 mm 145 mm
8 mm
±0,5mm ±0,5mm
±0,5mm
LOCKING CLAMP andLOCKING CLAMP EDGE
ZAMMER forthelockclipfastening
FASTENER FASTENER FASTENER
293 mm
242 mm 242 mm5 mm±0,5mm
ZAMMER forthelockclipfastening
CLIP andEDGE CLIPincl.screws(4x35mm),Bittx20
FASTENER FASTENER
CLASSIC VARIA
BAREFOOTBOARD 21 x 195 mm
L:420/480/600 cm
SMOOTH EDGE BOARD17 x 72 mm|L:360 cm
Partially-groovedsurfaceononesidewithcolourgradient,5mmgap
COLOURSVARiACHOCOLAteBLACK
VARiABROWN
VARiAGReY
195 mm 195 mm 5 mm5 mm 195 mm±0,5mm ±0,5mm
FASTENER
V
P5 GAP PROFILE Onaroll,forclosedCLASSiClongitudinalgap(Varia)
ROLLER Zammerattachmentfortheretractionofthejointprofile
OR
OR
SECURING CLAMP andEDGE CLAMPincl.screws(4x35mm),Bittx20
LOCKING CLAMP andLOCKING CLAMP EDGE
CLIP andEDGE CLIPincl.screws(4x35mm),Bittx20
OR
OR
P5 GAP PROFILE Onaroll,forclosedCLASSiClongitudinalgap(Varia)
DISTANZ FIXSpacerforfront-endjoints(whenlayinginapattern)
DISTANZ FIXSpacerforfront-endjoints(whenlayinginapattern)
Two construction beams (40 x60 mm)
DUO mounting
DUO edge panel
Screw (7.5 x 92 mm, pre-drill!)
Construction beams (60 x 40 mm)
Rubber pad (10 x 100 x 60 mm)for height compensation measuring 3/10/20 mm in thickness Concrete edge stone (50 x 1000 x 250 mm) (available from building material dealers)
Locking clamp
Connecting clip
70mm
10mm gap
min
. 121
320mm
70mm
Groove strip with clip 10mm gap
Concrete edge stone (50x1000x250mm)(available from building material dealers)
189
mm
Gravel formation level with a 2% gradient (in longitudinal direction of the plank)
Gravel formation level with a 2% gradient (in longitudinal direction of the plank)
Gravel formation level with a 2% gradient (in longitudinal direction of the plank)
Gravel formation level with a 2% gradient (in longitudinal direction of the plank)
Note: FIX STEP boards cannot constitute a gradient of their own.
Note: FIX STEP boards cannot constitute a gradient of their own.
Youshallfindexamplesofuseandtheassemblyinstructionsforlockingclampandtheclipat:www.megawood.com/137
Assembly instructions
360/420/480/540/600cm
OOTH EDGE BOARDmm | L: 360cm
OURS
CARDAMOM
242mm 242mm5mm±0,5 mm
mm 145mm 8mm8mm 145mm
±0,5 mm ±0,5 mm
mm 145mm 8mm8mm 145mm
±0,5 mm ±0,5 mm
!
Planning so�ware
_Virtually create the terrace in your own garden via the app
_Available as a download for tablets and smartphones
Outdoor living,outdoor is megawood®.
joint profile.taken into con
experience.
Online Plannerlaying
CONSTRUCTION PLAN BASISterracesystem
FIX STEP basis sub-structure
Basis concrete edge stone sub-structure
FIX STEP comfort sub-structure (raised)
min. 2%gradient recomm.
min. 2%gradient recomm.
min. 2%gradient recomm.
min. 2%gradient recomm.
min. 121 mm
min. 171 mm
7a
AttachtheFixStepfixturescentrallyusingastripofretainingband,clickintothepanelsandposition,ensuretheheightadjustmentisidentical.PositiontheFixStePDUOedgepanelsatthestartoftheterrace,distributetheFixStePstandardfixturesinaparallelmanner–pay attention to distances.PositionfurtherFixStePDUOedgepanelsattheendoftheterrace.ifrequired,turntheexternalFixStePpanelsinordertopreventaprotrusionoftheconstructionbeams.
intheeventofterracelengthsabove3.6m,positionFixStePDUOsmoothedgeboardsintheareaofthesmoothedgeboardbuttjoint.
Withthesmoothsidefacingupwards,clicktheconstructionbeams(40x60mm)intotheFixStePfixtures.
iftheterracewidthisgreaterthan3.6m,alwaysarrangetheconstructionbeamjointsinanoffsetmanner.Cuttheconnectingclipto320mm,connectthebeamjointswiththisclipandthentightlyscrewononeside.Positionthesmoothedgeboardsandconstructionbeamjointsinthesamelocation.Recesstheconnectingclipmeasuring20mminwidthand10mmindepthinordertoassemblethesmoothedgeboardintheareaofthescrewconnectionatalaterdate.Align the construction beams exactly. CLOSED GAP intheeventofadoublesmoothedgeboard,assembleconstructionbeam unitsmeasuring80mminlengthontoeachconnectingclipusingscrews.
Positionperforatedtapebeneaththeconstructionbeamsandscrewontoallconstructionbeamsusinganassemblyclip.
Sawintotheconstructionbeam,lockthelockingclampedgeinthegroove.
Adheretheretainingbandtotheconstructionbeamlocatedcentrallybeneaththefloorboards.
insertthefirstfloorboardintothehouseconnectionprofile(optional)andthenpushintothepositionededgeclamps. OPEN GAP Placethelockingclampsontheconstructionbeam,lockinplace withthezammer/pliersandinsertitintothefloorboardgroove. Applythenextfloorboard,useaspacer(for5/8mmgap)ifnecessary
CLOSED GAP Placethelockingclampsontheconstructionbeamandlockinplace withthezammer/pliers.Placethegroovestripontothefully assembledlockingclampand,together,pushintothefloorboardgroove.
ifthereisagrooveintheconstructionbeam,itmaybenecessarytouseagroovebridgeinordertoalsobeabletosecurelyfastenthelockingclampinthegaparea.
takeintermediatemeasurementsaftermax.1moflaidfloorboardrowsandscrewthecorrespondinglockingclamprowontotheconstructionbeam.
Cuttheconstructionbeamstosizeandensuretheyareflush – repeat step 6.
Cutthefrontalsideofthefloorboardstosizewitha15mmprotrusion,chamferthecuttingedge.thefrontalsideofthesmoothedgeboardsmustbe12mmshorterthantheconstructionbeamsattheendoftheterrace–pay attention to distances. OPEN GAP Frontalsideandlongitudinalsideassemblyofthesmoothedgeboards. CLOSED GAP Assembleconstructionbeamunitsmeasuring80mminlengthcom- pletewithassemblyclipatthestartandendofeachconstructionbeam. Screwdoublepiecesontotheterracecornersusingtwoassembly clips,indenttheDUOpanelwherenecessary. Frontalsideandlongitudinalsideassemblyofthesmoothedge boards.
OPEN GAP Layconcreteedgestones(1,000x250x50mm)atacentredistanceof 650mmonthegravelbedwithgradient,turnthefrontalsideinwardsby 50mminthedirectionoftheconstructionbeams.
CLOSED GAP Layconcreteedgestones(100x25x5cm)atacentredistanceof 750mmonthegravelbedwithgradient,turnthefrontalsideinwardsby 100mminthedirectionoftheconstructionbeams. OPEN GAP evenlydistributetheconstructionbeams(40x60mm)transverselyto theconcreteedgestones(grooveatthebottom),payattentiontoa 50mmprotrusion. CLOSED GAP evenlydistributetheconstructionbeams(90x90mm)transverselyto theconcreteedgestones,payattentiontoa100mmprotrusion.
Arrangetwobeamsrespectivelyatthestartandtheend.Lay10mmrubberpadsbeneaththeconstructionbeams,compensateforpossiblegradientdifferencesusingfurtherrubberpads.intheeventofaterracewidthgreaterthan3.6m,alwaysarrangetheconstruc-tionbeamjointsinanoffsetmanner(distanceof10mm).intheeventoftheterracebeinglongerthan3.6m,mountadditionalconstructionplankpiecesinthebuttjointsofthesmoothedgeboards. OPEN GAP Cuttheconnectingclipto320mm,connectthebeamjointswiththis clipandthentightlyscrewononeside. Screwtheendsoftheconstructionbeamsthroughouttheentireedge area.Screwthetwoouteraswellasthecentralconstructionbeams witheverysecondconcreteedgestone.Cuttheconstructionbeams tosize,ensuringtheyareflush. Sawintotheconstructionbeam,lockthelockingclampedgeinthegroove. CLOSED GAP Aligntheconstructionbeams,screwthesub-constructionintheedge areaaswellasbothstartandendbeamstothemiddlebeam.Cutthe constructionbeamstosize,ensuringtheyareflush,10cmprotrusion. the120mmlongconstructionbeamsmeasuring60x40cmareplaced uprightandthenfastenedtotheendsoftheconstructionbeamsonthe leftandrighthandsides.Adheretheretainingbandtotheconstructionbeamlocatedcentrallybeneaththefloorboards.
OPEN GAP insertthefirstfloorboardinthehouseconnectionprofile(optional), thenpressitintothepositionededgeclamps.Placethelocking clampsontheconstructionbeam,lockinplaceusingthezammer/ pliers,insertintothefloorboardgroove. Applythenextfloorboard,useaspacer(for5/8mmgap)ifnecessary. ifthereisagrooveintheconstructionbeam,itmaybenecessaryto useagroovebridgeinordertoalsobeabletosecurelyfastenthe lockingclampinthegaparea. takeintermediatemeasurementsaftermax.1moflaidfloorboar rowsandscrewthecorrespondinglockingclamprowontothecons- tructionbeam.Repeatuntilyoureachthelastfloorboardbutone. CLOSED GAP Screwtheedgeclipontotheendoftheconstructionbeamsothatit isflushwithit. Followingassemblyofthefirstfloorboards,pushthehouseconnection profileasaborderstriptothehousefacadetotheendoftheflorboard (optional).Fixthefloorboardswithaclip.tightenthescrewinsucha mannerthattheclipisparalleltothesub-construction. Looselyinsertthegroovestripintothefloorboardgroove,applythenext floorboard,pushontothegroovestrip,fixthefloorboardusingtheclip. Repeattheprocessuntiltheterraceisfullylaid. Cutthefloorboardstosizeintheedgeareafacingtheconstruction beams,chamferthecuttingedge.SeeFiguresand
thefrontalsideofthesmoothedgeboardsmustbe12mmshorterthantheconstructionbeamsattheendoftheterrace–pay attention to distances.
Circumferentiallyfastensmoothedgeboardstothesub-construction.Onthefrontalside,screwthesmoothedgeboardtothesub-constructionbeams.
Screwevery50cminaparallelmanneralongtheconstructionbeams,applyspacerscrewsbetweenthesmoothedgeboardandtheconstructionbeam.
SUB-
CO
NST
RUC
TIO
NFL
OO
RBO
ARD
ASS
EMBL
YSM
OO
TH E
DG
E BO
ARD
SSU
B-C
ON
STRU
CTI
ON
FLO
ORB
OA
RD A
SSEM
BLY
SMO
OTH
ED
GE
BO
ARD
S
4x35
10 mm
40 mm
15 mm
min. 15 mm
10 mm
40 mm
15 mm
min. 15 mm
10 mm
12 mm
2%
15b
4b
2%
Water drainage
Construction plan with FIX STEP
Construction plan with concrete edge stone
15a
15a
4
YouwillfindadditionalinstructionsonthelayingofaFixStePterracehere:www.megawood.com/124
Youwillfindadditionalinstructionsontheconstructionofaterracewithasubstructureofstoneswww.megawood.com/125
9b
15 mm12
0 m
m
100 mm
2b
12 mm
80 mm
8
1311
60 mm
12 mm
14 10 mm
40 mm
15a
Terrace widthTerrace lengthTerrace length
15b
40 mm
15 mm
min. 15 mm
8b 10 mm
40 mm
9a 10 mm
15 mm
40 mm
min. 15 mm
9b8a
10 mm
320 mm 70 mm
7,5x92
3a
3b10 mm
7,5x132
10 mm
32
0 m
m
2 31
50 mm
2a
10 mm
40 mm
15b
40 mm
60 mm
10 mm
4x35
10 mm
12 mm
6
L: 320 mm
4 70 mm
5b
5a
7a 7b
60 mm
12 mm 12 mm
4x35
4b
closed gap
open gap
4x35
11
7b
10 mm10 mm
M8x 80
mind. 15 mm 10 mm
min. 15 mm10 mm
closed gap
9a
Soil formation
80 mm
M8x 80
M8x 80
M8x 80
9a 9b
10
•
•
•
•
•
•
8
12
710
11
5
1a
1b
2a
2b
3a
3b
4
4
5a
5b
2
2
9a
9b
8a
8b
7
8
1
2
3
6
7
8
10
11
13
12
4
14
15a
14
14
4
9
57
•
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5
9
9b
9a
15b
15
4b
5
6
1a
1b
1
2a
2b
2
3a
3
3b
5a
5b
10
12
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
3
max. 500 mm
180 mm
4 %
2%
15amax. 500 mmmax. 500 mm
max. 650 mm
2%
max. 500 mm max. 500 mm
max. 600 mm
210 mm
max. 650 mm
max. 650 mm
max. 750 mm
min. 93 mm
min. 143 mm
min. 2%recomm. gradient
min. 2%recomm. gradient
min. 2%gradient required
min. 2%gradient required
15a
Terrace length
open gap
8
min. 2%recomm. gradient
min. 2%gradient required
7a
open gap
You will find additional instructionson the laying of a FixSteP terracehere: www.megawood.com/124
4
5a
9a
min. 2%recomm. gradient
7b
9b
closed gap
2%
15b
Care and cleaningCare instructions
Naturalfibreinclusionpriortotreatment
Naturalfibreinclusionfollowingmechanicaltreatment
Amin.2%gradientmakescareandcleaningeasier.ifthegradientisnotobserved,thismayleadtotheformationofwaterstainsandorganicsubstancesarethenabletosettleandahigherdegreeofsoilingisthenprobable.Werecommendcleaningtheterraceatleasttwiceperyearattemperaturesofatleast15°Candtoproceedasfollows:
•Brushdry,loosedirtfromtheterracedeck.
•Sufficientlywatertheentireterracedeck.
•Allowthewatertotakeaffectforatleast15minutes.
•Cleantheterracedeckusingwater,astiffbrushorascrubberandthoroughlyrinse.
Ournewmegawood®scouringpowder–removesdirt,whichcannotberemovedwithwaterandbrushesonly.itisalsosuitableforthesurfacecleaningofmegawood®terraces.
Waterstainsmayforminthetransitionalareabetweencoveredanduncoveredareasasaresultofprecipitationandenvironmentally-relateddustparticles.thesestainscangenerallyberemovedusingwaterandascrubberanddonotrepresentcauseforcomplaint.theeffectofthewaterstainslessensintimebutcannotbeentirelyavoided.
Youwillfindadditionalcareinstructionsintheterracepassinthedownloadareaofourwebsite: www.megawood.com/downloads
Forrawmaterialreasons,smallinclusionsofnaturalfibresmayoccur.Afterbeingsubjectedtoweathering,theymayrisetothesurfaceasaresultofwaterabsorption.Amaximumamountof0.03%ofthesurfacemaybeaffected.theparticlesizemaynotexceed0.5cm2.themajorityoftheparticleswilldisappearovertimeasaresultofterraceuse.
theycanalsobemechanicallyremoved.theproductwillnotbedamagedasaresult.BasedupontheePLF(europeanProducersofLaminateFlooring),theparticlesthatarevisiblefromstandingeye-levelunderverticalincidenceoflightareusedforassessmentpurposes.
Inclusion of fibres
Wateredges
Aftercleaningwithwater
Learnmoreonthecareforandcleaningofourproducts.www.megawood.com/123
Colour maturation
CLASSiC
PReMiUM PReMiUMPLUS SiGNUM DYNUM
TOP:AFteRLAYiNG
MIDDLE:AFteR1–2MONtHS
BOTTOM:AFteR6–8MONtHS
Special features
!
Ourinstallationguideforthestructurewithcrossbracingcanbefoundunder:www.megawood.com/137
min. 2%gradient recomm.
• Doublesub-constructionalongthe45° section.
• insertsealingtapeintothemitrejointon bothsides.
• Onlypushthefloorboardintothemitre profileby10mminordertoensurethe expansion.
• Whenattachingshortfloorboardsections (thatcanbefastendtotheloweredgewith lessthan3lockclampsorclips)onthe diagonalormitrecut,thesectionsare screwedtotheconstructionbeamfrom above.(M6x40mmscrew)
Laying on mitres for L, U, O-shaped terraces
20 mm
M6 x40
• theterracedeckisconstructedata deeperlevelsothestructureformsa singlelevelwiththesurroundingground surface.
• Amin.distanceof40mmbetweenthe constructionbeamsandrising,solid componentsmustalwaysbeobserved.
Construction at floor level with ventialtion grille
ClipMitre profile
Compress ribbon
Laying on roof terraces• Heightadjustmentandtheensuring ofamin.gradientof2%bylaying theFixStePboardsinabedof levellingmortar.
Levelling mortar
MITRE PROFILEAluminium21mmL:4 m
COMPRESS RIBBONexpandsupto20mmL:13m (onaroll)
CLIP & EDGE CLIPincl.screws(4x35mm),Bittx20
SCREW M6 X 40attachingshortfloorboarssections
• Adistanceofatleast20mmbetween theboardsandraised,fixedcomponents mustalwaysbemaintained.
• ensurethattheleveldeckisdesignedwith aopengapinordertoensureventilation frombeneathandfromtherear.
• Onlyimplementalevelfloorboard
above.
Construction at floor level with ventialtion grille
20mind. 2%
recomm. gradient
VENTILATION GRILLEH:21mm;B:105mmL:2.000mmStainlesssteelV2Abrushed
Construction at floor level with ventialtion grilleConstruction at floor level with ventialtion grille
Furtherinformationregardingroofterraceconstructionorotherspecialconstructionmethodsareavailabledirectlyfromthemanufacturerandwww.megawood.com
structurewitha5mminconjunctionwith aventilationgrid.
• Useoftheventilationgrid(alsowith „placed-on“deckorintheeventofa closedgap)inordertoimprovetheair circulationbeneaththeterraceandto increasetheservicelifeoftheentiredeck.
Laying as a deck with herringbone pattern
Gradient in the laying direction
4%
2%
max. 50 cm
Herringbone pattern
2%Recommended gradient
Soil formation level
Gravel formation level
• Anadditionaldoublesub-constructionis tobelaidinallareaswheretherearebutt jointsontheheadside.
• theDiStANZFixispositionedbetween thedoubleloweredgesinordertoforma gapbetweenthebuttjointsonthehead side.
DISTANZ FIX
Cross bracing structure • Prerequisiteforthecrossbracingis aload-bearingsubstrate(concrete, concretekerbstone)ortheinstalla- tionwithFixSteP.Whenlaidwithout FixSteP,thestructureisbuilton20mm highrubberpads,whichareinstalled atthecrossingpointsoftheconstruc- tionbeamstoensuretheminimum distance.
• thecrossbracingmustbesecurely connectedtothesubstrate.• thegeneralplanningprinciplesofmegawood®constructionplanterrace systemapply.
Constructioninformationandinformationregardingtheventilationgridisavailableatwww.megawood.com/136
Construction information andinformation regarding theventilation grid is available atwww.megawood.com/136
Constructioninformationandinformationregardingtheventilationgridisavailableatwww.megawood.com/136
NAtURALBROWN LAVABROWNBASALtGReY SLAteGReYNUtBROWN VARiAGReYVARiABROWN VARiACHOCOLAteBLACK
tONKAMUSKAt NiGeLLACARDAMOMNAtURALBROWN LAVABROWNBASALtGReY SLAteGReYNUtBROWN
Related Documents
