This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
CONCRETE ADMIXTURE®PLASTCONE AP211 Water reducing concrete admixture
Benefits• Permits concrete placement in congested reinforcement
concrete• Reduce water cement ration by 8 to 10% • Improve workability and compressive strength• Higher durability• To create impervious and dense concrete, ideal for slopping
roof, thin shell roof
Method of applicationThe dosage ratio depends on mix design and site specification requirements, recommended dosage as a guideline is 100 to 300ml of 50kg cement
Pack size : 1,5,10,20 & 200lit
Application AreaCement Concrete work • Cement Mortar work • Cement Plaster work
Reinforced and unreinforced concrete • Column and beam
Benefits• Permits concrete placement in congested reinforcement
concrete• Reduce water cement ration by 8 to 10% • Improve workability and compressive strength• Higher durability• To create impervious and dense concrete, ideal for slopping
roof, thin shell roof
Method of applicationThe dosage ratio depends on mix design and site specification requirements, recommended dosage as a guideline is 150 to 300ml of 50kg cement
Pack size : 1,5,10,20 & 200lit
Application AreaCement Concrete work • Cement Mortar work
Reinforced and unreinforced concrete • Column and beam
Benefits• Permits concrete placement in congested reinforcement
concrete• Reduce water cement ration by 15 to 20% • Improve workability and compressive strength• Make concrete as pump able• Higher durability• To create impervious and dense concrete, ideal for slopping roof,
thin shell roof
Method of applicationThe dosage ratio depends on mix design and site specification requirements, recommended dosage as a guideline 0.6 to 1% of 50kg cement
Pack size : 250kg HDPE Drum
Technical information
Properties Results
Appearance Free Flowing thin liquid
Colour Brown
Sp. Gravity @25OC gms/cc 1.15 0.02
Non Volatile content 13 0.05%
PH Value 7-8
Setting time, minutes initial -100; Final -280
Chloride contents Nil
Water permeability >80% of the control
Application AreaCement Concrete work • Reinforced and unreinforced concrete above M30
Column and beam • Precast concrete • Pre stress concrete
03 REDWOP CHEMICALS PVT. LTD.
PLASTCONE HS200
Superplasticising Admixture
CONCRETE ADMIXTURE®PPROCRETE R20Polycarboxilic ether based super plasticizer admixture
Benefits• Permits concrete placement in congested area of reinforcement
concrete• Reduce water cement ration by 18 to 30% • Improve workability and compressive strength • Make concrete as pump able• Higher durability & finishing concrete• To create impervious and dense concrete
Method of applicationThe dosage ratio depends on mix design and site specification requirements, recommended dosage as a guideline 0.6 to 1% of 50kg cement
Pack size : 210kg HDPE Drum
Application AreaCement Concrete work • Reinforced and unreinforced concrete above M40 to M100
Column and beam • Precast concrete • Pre stress concrete • Accelerating Concrete work
04REDWOP CHEMICALS PVT. LTD.
Technical information
Properties Results
Appearance Free Flowing thin liquid
Colour Brown
Sp. Gravity @25°C gms/cc 1.05 0.02
Non Volatile content 13 0.05%
PH Value 7-8
Setting time, minutes initial -100; Final -280
Chloride contents Nil
Water permeability >80% of the control
PROCRETE R20
CONCRETE ADMIXTURE®PLASTCONE RRetarder cum water reducer
Benefits• Reduce water cement ration by 5 to 8% • Improve workability and compressive strength • Higher durability & finishing concrete• To create impervious and dense concrete
Method of applicationThe dosage ratio depends on mix design and site specification requirements, recommended dosage as a guideline 0.6 to 1% of 50kg cement
Pack size : 210kg HDPE Drum
Technical information
Properties Results
Appearance Free Flowing thin liquid
Colour Brown
Sp. Gravity @25OC gms/cc 1.05 0.02
Non Volatile content 13 0.05%
PH Value 7-8
Setting time, minutes initial -100; Final -280
Chloride contents Nil
Water permeability >60% of the control
Application AreaCement Concrete work • Reinforced and unreinforced concrete where some retardation is required
Column and beam • Series and time framing concrete work
05 REDWOP CHEMICALS PVT. LTD.
CONCRETE ADMIXTURE®BLOCKFAST ANThe dosage ratio depends on mix design and site specificationrequirements, recommended dosage as a guideline 0.6 to 1% of 50kg cement
Benefits• Permits concrete placement in congested area of
reinforcement concrete• Reduce water cement ration by 10 to 12% • Improve workability and compressive strength • Higher durability & finishing concrete• To create impervious and dense concrete
Method of applicationThe dosage ratio depends on mix design and site specification requirements, recommended dosage as a guideline 0.6 to 1% of 50kg cement
Pack size : 210kg HDPE Drum
Application AreaCement Concrete work • Reinforced and unreinforced concrete • Column and beam
Precast concrete • Pre stress concrete • Accelerating Concrete work • Concrete work near sea area
Benefits• Permits concrete placement in congested area of reinforcement
concrete• Improve workability for a long time• Make concrete as pump able
Method of applicationThe dosage ratio depends on mix design and site specification requirements, recommended dosage as a guideline 80ml per 100kg cement
Pack size : 200ltr. HDPE Drum
Technical information
Properties Results
Appearance Free Flowing thin liquid
Colour Light Yellow
Sp. Gravity @25OC gms/cc 1.05 0.02
Non Volatile content 13 0.05%
PH Value 8
Setting time, minutes initial -100; Final -280
Chloride contents Nil
Application AreaConcrete Road, Bridge duck, airport runway & taxi parking area • Reinforced and unreinforced concrete
where freezing and thawing effect to be nullified • Column and beam • Light weight concreteReducing segregation and bleeding • Use wide range of aggregate
Benefits• Acce lera t ing admix ture for unre in forced cement
concrete/mortar • Higher durability & finishing concrete• To create impervious and dense concrete• Enables earlier release from precast moulds thus speeding
production • Accelerates the hardening of floors and screeds.
Method of applicationThe dosage ratio depends on mix design and site specification requirements, recommended dosage as a guideline 0.6 to 1% of 50kg cement
Pack size : 250kg HDPE Drum
Application AreaCement Concrete work • Reinforced and unreinforced concrete
Dosage is normally in the range of 7.5 to 22.5 litre / m3 (approx. 2 - 6 % by weight of cement). The following table may be used for guidance. The level of corrosion inhibition increases with dosage.
Pack size : 250ltr. HDPE Drum
Technical information
Properties Results
Appearance Free Flowing thin liquid
Colour Water Color
Sp. Gravity @25OC gms/cc 1.25 0.02
Non Volatile content 17 0.05%
PH Value 7-8
Setting time, minutes initial -100; Final -280
Chloride contents Nil
Application AreaCement Concrete work near to sea area where freechloride avail • Reinforced concrete • Column and beam
09 REDWOP CHEMICALS PVT. LTD.
PLASTCONE
AIRENT
Corrosion inhibiting reaction with steel in concreteshown as bellow by our admixture
Benefits• Admixture is used as corrosion inhibiting admixture• Can be used in conjunction with other admixtures• Will not affect workability and strength of concrete
Typical DosageThe dosage of PLASTCONE BPO should be as determined in the concrete mix specification depending on the chloride ions expected at the surface of the steel within the life expectancy of the concrete structure. Based upon FHWA recommended 0.90 chloride to PLASTCONE BPO solution.
Chloride threshold kg/m3 Recommended dosage of plastcone bpo admixture( litres/m3)
Swimming pool • Door & Window seal • External stone
16REDWOP CHEMICALS PVT. LTD.
Technical information
Properties Results
Appearance Free flowing powder
Color White/Grey
Pot Life@25° C, minutes >20
Adjustability time, minutes 15 min, 30°C
Open Time 30 min, 30°C
Trafficable time, Hrs 24
Shear adhesion 20.0KN after 14day ( as per IS:15477 is 10KN)
IS : 15477
CM/L-7600053173
PROLIX
TILE ADHESIVE®FLEXOPLUSWood & steel two pack adhesive
Features• Suitable for fixing vitrified tile for floor & wall• Two Part Epoxy Reactive adhesive• Very Good strength• Used for spot bonding• Excellent squeezability• Fast cure
Application ProcedureMixed Base and Hardener properly and then appliedPrimer 25 is recommended for better bonding.
Pack size : 2kg & 5kg Kit
Application AreaTiles or Stone on wood • Tiles on steel and aluminum
Tile on cement sheet • Cement article to cement article
17 REDWOP CHEMICALS PVT. LTD.
Technical information
Properties Results
Compressive strength 40N/mm2 after 24hr
75N/mm2 after 7days
Tensile strength Concrete failure
Shear Strength 13N/mm2
squeezability Meet the requirements
Colour Base White
Hardener Light Yellow
Mixed Off white
TILE ADHESIVE®EPTILE GROUTEpoxy Tile Grout
Application Procedure6.5 lit clean water to be used in 20kg bag, mix it properly and applied with trowel
Features• Impermeable to water • Resistant to shrinking, flaking or cracking • Non-fading over a period of time • Easy to apply • Non shrink• Durable• Good abrasion resistance
19 REDWOP CHEMICALS PVT. LTD.
WATERPROOFING CHEMICALS®POLYCOTE WH Single component acrylic polymer for cement basedwaterproof composite coating membrane
Application AreaRoofs • terraces • balconies as a sandwich layer • Pools and fountains
Reservoirs and channels • End walls subjected to rain • Toilet & Bathroom
20REDWOP CHEMICALS PVT. LTD.
Advantages • Non - toxic, non-flammable and user friendly • Provides a tough, impermeable waterproof membrane • Can be applied by brush, on horizontal and vertical surfaces • Excellent adhesion to concrete and masonry surfaces • Protects concrete and mortar from natural elements such as wind, rain, sunlight • Breathable - allow inside water vapour to escape
Application Procedure
Pack size Available in 125ml, 250ml, 500ml, 1, 5, 20, 50, 200 ltr packs.
Priming Coat1 part of POLYCOTE WH: 2 parts of Water: 4 parts of Cement Mixed material with the above proportion will cover an area of 16-17m2 for 1L of POLYCOTE WH
TopcoatPOLYCOTE WH acrylic polymer shall be mixed with neat cement in the ratio of 1:2 respectively, to obtain uniform and consistent slurry avoiding any lump formation.40ft2 per lit POLYCOTE WHFor white colour - mix white cement, for other colours; add cement compatible pigments to white cement
Application AreaRoofs • terraces • Swimming pool • Pools and fountains • Reservoirs and channels • Toilet & Bathroom
Advantages • Non - toxic, non-flammable and user friendly
• Provides a tough, impermeable transparent waterproof membrane
• Can be applied by brush, on horizontal and vertical surfaces
• Excellent adhesion to concrete and masonry surfaces
• Protects concrete and mortar from natural elements such as wind, rain, sunlight
Application ProcedureMix 5 lit liquid with 10kg powder in bucket by small agitators then brush it on surface
Features• Excellent dirt pick up resistance at all film thickness
• Outstanding weatherabilty
• Very good Compatibility with thickeners
• Very high alkali resistance
Coverage :70 to 100 ft2 per set (5lit liquid + 10kg powder)
Pack size : 5kg liquid & 10kg powder
21 REDWOP CHEMICALS PVT. LTD.
Technical information
Properties Results
Pot life @20°C 1 hour
@ 35°C 20 min.
Mixed Density 1.90kg/liter (brush able Consistency)
Tensile strength 2 N/mm2 (at 1.5mm Thickness)
Colors Grey / White
Application temperature Not less than 10°C
Toxicity Non-toxic
Adhesion to concrete >1N/mm2
TILE ADHESIVE®SUPERKOT Liquid membrane waterproofing in white color
Application AreaRoofs • Terraces • Pools and fountains • Reservoirs and channels • Toilet & Bathroom • Externals wall
22REDWOP CHEMICALS PVT. LTD.
Technical information
Properties Results
Surface Dry time 30min.
Adhesion to concrete Excellent
Recoating interval 4 to 5 hr @ 300 C
Elongation 150%
UV resistance Excellent
Colors White
Toxicity Non-toxic
Advantages • Film thickness Provides higher dry film thickness of
Minimum 1 mm in three coat application.
• Crack bridging Good Bridges cracks.
• Suitability Can be used for flat as well as sloping roofs
• Strength Good tensile strength, tear resistance & bond
strength with cementitious substrates.
• Resilience Forms highly elastic & resilient coating so helps to
withstand the structural movements.
• Durability Resistant to UV & weather conditions.
• Abrasion resistant No additional protective coating is required for roof
• Ease of application Can by applied by brush &roller easily.
• Temperature reduction by 8- 9 deg. C @ 45 deg. C Surface temp.
• Toxicity It is Non-toxic in nature, Eco friendly
Application ProcedureFirst do primer coat by our PRIMER WB & apply SUPERKOT by brush.
Coverage : For waterproofing: 40 to 50ft2 per lit
For paints: 70 to 80 ft2 per lit
Pack size : 1,5,10 & 20kg
WATERPROOFING CHEMICALS®POLYCOTE CWPCrystalline capillary waterproofing system for cementitious substrates
Application AreaSewage treatment • water treatment plants • Tanks • Foundations & tunnels and manholes.
Terrace garden, balconies, sunshades etc • Roof and Sunken slabs • Industrial and office buildingsReservoirs, water holding structures etc.
Advantages • Use for portable water
• Penetrates concrete, seals capillary tracts
• Contains no chloride
• Easy to apply
• Resists chemical attack of sewage and industrial wastes
• Suitable for external and internal applications.
Application Procedure3 part powder & 1 clean water to be mixed by paddle mixer and apply it on surface
Features• Excellent dirt pick up resistance at all film thickness
• Outstanding weatherabilty
• Very good Compatibility with thickeners
• Very high alkali resistance
23 REDWOP CHEMICALS PVT. LTD.
Mechanism Polycote CWP crystalline waterproofing system penetrates concrete and react chemically with free lime to produce insoluble crystals. This crystalline growth reduces porosity by blocking capillaries and filling hairline non structural cracks
Coverage : Polycote CWP : 1 to 1.5 kg/m2 per application (brush)
Pack size : Polycote CWP: 5KG & 20KG bags
WATERPROOFING CHEMICALS®POLYCOTE WH-100Straight acrylic transparent polymer for exteriors waterproofing
Application AreaRoofs • Terraces • Swimming Pool Tiles • Pools and fountainsReservoirs and channels • Toilet & Bathroom • Externals wall
24REDWOP CHEMICALS PVT. LTD.
Technical information
Properties Results
Solid content 50+-1%
PH @27°C 7 to 8.5
Viscosity at 23 °C 1000 to 2000mPa.s
Density 1.04
Resistance to frost °C ≤ 0
Type of emulsion Anionic
Advantages • Non - toxic, non-flammable and user friendly
• Provides a tough, impermeable transparent waterproof membrane
• Can be applied by brush, on horizontal and vertical surfaces
• Excellent adhesion to concrete and masonry surfaces
• Protects concrete and mortar from natural elements such as wind, rain, sunlight
• Balanced mechanical properties
• Gives excellent water Resistance
Features • Excellent dirt pick up resistance at all film thickness
• Outstanding weatherabilty
• Very good Compatibility with thickeners
• Self cross-linking
• Very high alkali resistance
Coverage : 40 to 50 ft2 per lit
Pack size : 1, 5,10 & 20 lit drum
WALLPUTTY®WHITEPLASTWall Putty
Application AreaRoofs • terraces • Swimming pool • Pools and fountains • Reservoirs and channels • Toilet & Bathroom
Application Area• Wall outer and inside
• RCC Ceiling area
Features• To provide a water-resistant, smooth finish leveling
compound for concrete walls, masonry and brick surfaces.
• Suitable for both Internal and external applications
• Water-resistant
• Excellent adhesion to host substrate
• Smooth finish
• Low water absorption
• Suitable for leveling prior to the application of oil based or water based paints coating
25 REDWOP CHEMICALS PVT. LTD.
Application Works Care should be taken to ensure that WHITPLAST PUTTY is thoroughly mixed. Mix in a suitable size container using an approved spiral paddle attached to a slow speed (400/500rpm) heavy-duty drill. Place 4.8 - 5.1 litres of cool, clean drinking quality water in the mixing container followed by the powder and mix thoroughly. Small quantities can be hand mixed by blending 2.5 - 3 parts powder to 1 part by volume of cool, clean, drinking water.
Coverage300ft2 per 20kg bag @ 0.5mm thickness
Pack size 1,5,20kg bag
NON SHRINK GROUT®ARACONE GP2Non Shrink Grout for machine & shed base plate
Application AreaRoofs • terraces • balconies as a sandwich layer • Pools and fountains
Reservoirs and channels • End walls subjected to rain • Toilet & Bathroom
26REDWOP CHEMICALS PVT. LTD.
Application Area• Used for precision grouting where it is essential to withstand static and
dynamic loads.• Typical applications would be the grouting of base plates of turbines,
compressors, boiler feed pumps etc.• It can also be used for anchoring a wide range of fixings.• These include masts, anchor bolts and fence posts.
Features• Gaseous expansion system compensates for shrinkage and settlement in the plastic state • No metallic iron content to cause staining. • Pre-packed material overcomes onsite batching variations • Develops high early strength without the use of chlorides • High ultimate strength ensure the durability of the hardened grout • Free flow ensures high level of contact with load bearing area
Time for expansion (after mixing)Start: 20 minutes Finish: 120 minutes
Fresh wet densityApproximately 2220kg/m3 depending on actual consistency used
Application Area• Special provide a highly abrasion resistant surface to concrete floors• They are ideally suited for all industrial areas subject to the heaviest traffic• Loading bays, trucking lanes, car parks, workshops, machine shops, ramps and spillways.
Features• Non metallic - does not rust or stain
• Provides a hard, abrasion resistant surface
• Forms monolithic bond with base concrete
• Easy and economical to apply
Application procedureHARDFLOOR Dry powder to be sprayed on running RRC work and Tri mix disc to be applied for increasing hardness of surface
Coverage : min. 3kg per m2 area
Pack size : 25kg bag
27 REDWOP CHEMICALS PVT. LTD.
Technical specifications
Abrasion resistanceSpecial improves the abrasion resistance of concrete by 250%.
Compressive strengthAt water contents equivalent to those obtained in practical applications, the typical 28 days compressive strength of HARDFLOOR Special cubes is 90 N/mm2.
Hardness (Moh’s Scale)The selected aggregates contained within HARDFLOOR(H) Special have a hardness value of 7 on the Moh’s original scale
Application Area• For economical repairs to damaged reinforced concrete elements, particularly where access is restricted.
• Where vibration of the placed material is difficult or impossible.• Suitable for various structural strengthening measures such as filling honeycombs and cracks.
28REDWOP CHEMICALS PVT. LTD.
Advantages • Gaseous expansion system compensates for shrinkage and settlement in
the plastic state. • Can be pumped or poured into restricted locations. • Highly fluid to allow for placement without vibration. • Pre-packed to overcome site-batched variations. • Low permeability • Economical • Contains no chloride admixture. • Ease of use
Application Procedure4.75 lit water to be added in 25kg powder bag and mixed it well then to be pour where required
Pack Size : 25kg powder bag
Properties 1. Compressive strength 1 Day 8N/mm2 7 Day 25N/mm2 28Day 35N/mm22. Flexure Strength 3 N/mm2 after 28days3. Density 2100 to 2200 kg /m34. Unstrained expansion 1-4 %
POLYESTER ANCHOR GROUT®ANCHOSINE P FIXPolyster anchor grout for baring rebaring
Application Area• high strength corrosion resistant anchoring of bolts and bars from 12 - 51mm
diameter into concrete, rock, masonry or brickwork where high speed of installation and early application of load is required
• Permanent installation of reinforcement starter bars, foundation bolts, base plates, balustrading, barriers and safety fences, railway tracks, tie-back anchors
Features• Rapid strength gain
• Vibration resistant
• Corrosion resistant
• Non expansive
• Can be placed under water
• It is used in overhead or horizontal holes.
• The thixotropic nature of Anchosine polyester resin grout P reduces flow of grout out of the hole.
29 REDWOP CHEMICALS PVT. LTD.
Properties Specific Gravity : 2.9
Pack size 1kg & 5kg
MICRO CONCRETE®MAZIK COATAliphatic acylate anti carbonation paints
Application Area• For economical repairs to damaged reinforced concrete elements, particularly where access is restricted.
• Where vibration of the placed material is difficult or impossible.• Suitable for various structural strengthening measures such as filling honeycombs and cracks.
30REDWOP CHEMICALS PVT. LTD.
Advantages • All type of structure which is directly exposed to sea area• To protect structures from attack by acid gases, chloride ions, sulphates,
oxygen and water• MAZIK COAT is also suitable to protect cementitious substrates and
masonry.
Features• Protects exposed reinforced concrete structures from atmospheric
gases-excellent barrier to carbon dioxide, chloride ions, sulphates, oxygen and water
• It resists efflorescence and lime blooming with good adhesion on all cement plasters. It hides surface undulations and fine surface cracks
• UV resistant- aliphatic acrylate gives resistance to long term weathering.• It contains special glass fibers to maintain anti cracking properties.
Technical information
Properties Results
Adhesion to concrete Good
Water permeability Nil after 24 hours.
Resistance to chloride,
sulphate ions and carbonation Good
UV resistance Good
Breathability Breathable
Wet film thickness / coat 200 microns
Coverage : 70 to 80ft2 per lit
Pack Size : 1, 5, 10 & 20 lit
®BITUCOTE Bituminous primer protective coating on RCC structure
Application Area• To provide a continuous barrier to the passage of water and water vapor
• can be used to produce vapor barriers, damp proof courses, linings to potable water tanks and pipes, below ground concrete protection, concrete curing by water retention, and corrosion protection to metal surfaces
Advantages• Single component
• Easily and inexpensively applied; high coverage rate
• Tough and resistant to most naturally occurring chemicals
• Does not taint water
• Can be applied to damp concrete substrates
• Quick drying
• Excellent adhesion to most common building substrates
• Excellent water retention for use as a curing compound
• Successfully used for over 30 years in a wide range of environments
31 REDWOP CHEMICALS PVT. LTD.
Application Procedure Surfaces must be clean, dry, free from oil, grease and all loosely adhering particles such as rust, mill scale, mortar and cement laitance. Then BITUCOTE should be applied by Brush application.
Coverage 30 to 40 ft2 per lit
Pack size 10 & 20 lit
® BITUCOTE M1M Bituminous protective Compound on RCC (up to 2mm)
Application Area• To provide a continuous barrier to the passage of water and water vapor
• can be used to produce vapor barriers, damp proof courses
• Below ground concrete protection
Advantages• Single component
• Easily and inexpensively applied
• Tough and resistant to most naturally occurring chemicals
• Does not taint water
• Can be applied to damp concrete substrates
• Successfully used for over 30 years in a wide range of environments
• It has a good bonding with external plaster
Application Procedure It is a in slurry form so should be used by brush or mala patra
• Versatile - Compatible with all common hydraulic cements.
• Cost effective - BUTABOND SBR is economical to use
33 REDWOP CHEMICALS PVT. LTD.
Pack size Ava i l ab le in 125ml , 250ml, 500ml, 1, 5, 20, 50, 200 ltr packs.
BITUMINOUS PROTECTIVE COATING
Butabond SBRMicro Concreting & Waterproong
Technical information
Properties Results
Type Styrene butadiene
polymer rubber
Color white
Sp.gr. 1.02 +-0.02
Storage condition Free from frost
Hard dry 5 to 6 hr
® EPKOTE ET140Tar based epoxy coating for steel and concrete surface
Application Area• Provides protection to concrete and metal structures against corrosion from
aggressive environments.
• Suitable for tanks above ground or in totally submerged conditions such as pipelines
• Particularly useful in sewage works, effluent plants and dock and harbor installations.
Advantages • Excellent resistance to all types of water
• Easily applied by brush or spray
• Easily applied by brush or spray
• Provides long term corrosion protection
• No priming necessary in most cases
• Chemical and abrasion resistant
• Economic and versatile product
Application ProcedureResin & Hardener to be mixed with a stirrer then apply by brush and spray
Chemicals resistance to • Water
• Sea Water
• Ground Water
• Sewage Water
• Distilled Water
• Atmosphere Condition
• Exhaust and sewage gases
• Salt Solutions
• Many Organics Solutions
• Distilled minerals and alkali
• Vegetables minerals oil & Fats
• Binnacles and organics growth
BITUMINOUS PROTECTIVE COATING
34REDWOP CHEMICALS PVT. LTD.
Technical information
Properties Results
Pot life at 30 °C 1.5hr
Time between coat 2hr
Initial Hardness at 30 °C 6hr
Coverage115ft2 per 5kg set at thickness of DFT 300 micron
Pack size 5kgs & 30 kg set
® REDICURE WBWax based curing compound
Application Area• For spraying on freshly cast concrete, or newly exposed concrete surfaces after
removal of form work, to form a temporary membrane which will retain sufficient moisture for effective curing to take place.
• Used for concreting generally but especially useful for large areas of concrete such as pavements, runways and bridge decks.
• Also for vertical or sloping surfaces as on towers, chimneys, canal linings, columns and beams, where water curing is difficult or unreliable.
Advantages • Single application - Forms moisture barrier for whole of the curing period.
• No other curing necessary - Eliminates use of water, hessian or sand, completely.
• Reliable - No risk of erratic or poor curing and ensures that cement hydrates efficiently.
• Ensures hard-wearing surface - Minimizes risk of drying shrinkage, cracks and dusty surfaces.
• Easy and sage spray application - Non-toxic and nonflammable.
35 REDWOP CHEMICALS PVT. LTD.
CURING COMPOUND
ApplicationExposed concrete slabs: REDICURE WB should be spray applied on to the newly placed concrete slab as soon as possible after it is free from visible surface water, e.g. typically 1 to 2 hours after placing. Shuttered and precast concrete: REDICURE WB curing agent should be spray applied to all surfaces as soon as formwork has been removed or the element remolded.
Properties • Color Bulk liquid - White
• Minimum application temperature – 10°C
Coverage : 60ft2 per lit
Pack size : 20lit, 50lit & 200lit
® EPFLOOR MM22mm thick epoxy resin based floor topping
Application Area• EPFLOOR MM2 is designed for use in
wide range of industrial environments where a lasting solution to floor maintenance problems is required.
• It provides a dense, impervious, coloured and chemically resistant floor surface which is hygienic and easy to clean.
• Clean rooms
• Laboratories
• Kitchens
• Plant rooms
• Light industrial plants
Application ProcedureMix base,Hardener and color paste properly and mix filler part in it then apply by trowel and spike roller
EPOXY FLOOR COATING
36REDWOP CHEMICALS PVT. LTD.
Technical information
Properties Results
Pot Life at 27oC 1hr
Compressive strength at 7days 50N/mm2
Flexure strength at 7days 34N/mm2
Shore D Hardness 80
Cure Time foot traffic 24hr
Vehicular traffic 7days
Chemical Resistance 7days
Advantages • Fast application - minimizes downtime
• Chemically resistant – good resistance to a wide range of chemicals
• Durable – Goods abrasion resistance
• Hygienic - provide a dense, impervious, seamless floor surface which is easily cleaned
• Attractive - available in a wide range of colors to enhance the work ing Environment
Application Area• To provide a hard wearing, easily cleaned, attractive floor coating in areas where
high resistance to chemical attack is required.
• It is suitable for use in production assembly areas, workshops, dairies, soft drinks production and bottling plants, kitchens, showrooms etc.
• It is particularly suitable in wet working areas and where chemical spillage is likely, e.g. plating shops, processing plants, dye works etc.
• It can also be used as a final coating and sealer for epoxy floor screeds to provide a more durable and easily cleaned surface where high impact is desirable.
Advantages • Hard wearing - durable, low maintenance costs
• High resistance to a wide range of industrial chemicals
• Attractive - available in a range of colors to improve the working environment
Coverage : Primer 25 : 60 to 70ft2 per lit • EPKOTE PE280 : 50 to 60ft2 per lit
Pack size : 1lit and 5 lit set
37 REDWOP CHEMICALS PVT. LTD.
EPOXY FLOOR & STEEL COATING
Technical information
Properties Results
Pot life 4hr at 200C
Tack Free time 5-6 hr at 200 C
Time between coat 24hr
Initial Hardness 24hr
Full cure 7day
Wet film thickness 100micron( single coat)
Dry film thickness 90micron (two coat)
Chemical resistance to Citric Acid 10% : Resistant
Hydrochloric Acid (10%) : Resistant
Lactic Acid (10%) : Resistant
Sulphuric Acid (10%) : Resistant
® EPMORTAR EREpoxy Mortar
Application Area• For fast and emergency resin statement of concrete.
• For bedding, jointing, profiling of concrete, repair of damaged concrete in precast units.
• Jointing between precast units.
• Repair of stair treads, fixing tiles.
• Cladding, repairs to kerbs, man hole covers, door and window frames etc.
EPOXY MORTAR
38REDWOP CHEMICALS PVT. LTD.
Pack size :5KG SET
Advantages • Durable - Stronger than concrete. Highly chemical and oil resistant.
Excellent bond strength.
• Ease of application - Mix resin and hardener in any proportion as required. No primer is required.
• Quick - Finish job operation in 2 - 3 hours.
• Versatile - Can be poured, trowelled, filled with coarse aggregates. Will cure in dry, wet, damp, and under water conditions. Can be used at down to 00C or upto 600C.
Application Area• Sealing movement joints in building
• Civil engineering structures, including superstructures, reservoirs, floors, basements and subways
• RCC Road groove filling
• The cured sealant exhibits excellent adhesion to most surfaces including primed concrete, glass, aluminum and stainless steel.
Features• A high quality product meeting key international standards
• Forms a tough, elastic rubber-like seal
• Accommodates continuous and cyclic movement
• Excellent adhesion to most common substrates
• High resistance to ageing reduces physical damage due to climatic extremes
Application ProcedureResin and Hardener to be mixed properly and fill it where requirements
41 REDWOP CHEMICALS PVT. LTD.
POLY SULPHIDE SEALANT
REDOFLEXPoly Sulphide Sealant
ColorGrey
Pack Size4kg Set
®REDOSEALOne Part Low Modulus Polyurethane Sealant
Application Area• Building expansion joints where elasticity is required
• Sealing joints in precast elements
• External walling
• Curtain walling and cladding
• Panel wall, door and window perimeter sealing
• Crack sealing in waterproofing works
Features• One part, reduces the possibility of applicator error and possible joint failure
Excellent thixotropy - non-sag
• Elastic low modulus
• Pitch-free - overpaintable
• Movement capability +/- 25%
• Bubble-free curing, no weak areas for air bubbles to develop
• Excellent resistance to weathering (DIN14231)
• Very good adhesion to most construction materials especially concrete without the need of primer
• Permanently elastic over a wide range of temperatures
PU SEALANT
42REDWOP CHEMICALS PVT. LTD.
Pack size 600ml capsul
Redoseal
PU Sealant
Technical information
Chemical Basis Polyurethane
Cure Mechanism Moisture curing
Specific Weight 1.42 +/- 0.02gr/cc
Tack free time at 23°C and 50% R.H. ≈ 120 minutes
Curing at 23°C and 50% R.H. ≥ 2,5 mm/24h
Hardness Shore A (DIN 53505) 20-25
Elastic modulus at 100% (DIN 52455) ≤ 0,5 N/mm2
Tensile strength (DIN 53504) 1,5 N/mm2
Elongation at break (DIN 53504) ≥ 600%
Temperature Resistance -40°C - +80°C
® SILICOREP S500Colorless solvent based water repellent
Application Area• SILICOREP S500 is used to provide water repellent surface
with improved self cleaning properties on exterior building.
• Brick work, concrete, cement rendering, natural or cast stone.
Advantages • Brush or spray applied direct from container.
• Equally effective on old or new surfaces.
• Unaffected by salt-laden atmosphere, reduces unsightly staining.
• Risk of efflorescence is reduced.
• Reduces causes of cracking and crazing in in-situ or precast concrete.
• Preserves natural color and texture of created material.
Penetration • SILICOREP S500 penetrates into concrete for a minimum
depth of penetration of 2mm
43 REDWOP CHEMICALS PVT. LTD.
WATER REPELLENT
Water resistance Repels rain water and inhibits ingress of surface water provided there is no hydrostatic pressure.
Permeability Permeability is low to water, salt solution, dust and soot particles. Leaching of soluble salts from brick work, which causes efflorescence, absorption of deicing salts by concrete which causes degradation and absorption of atmospheric dirt by brickwork, concrete and stone are all minimized.
Water vapor release SILICOREP S500 allows building surfaces to breathe naturally.
Coverage: 45 to 90 ft2 per lit ( Depends of Porosity of stone)
Pack Size : 1lit,5lit,10lit & 20lit
® SILICOREP WR100Colorless silicone based water repellent
Application AreaWater repellent treatment for
• Cement painted surfaces.
• Concrete, mortar
• Clay brick surfaces.
• Natural and artificial stones.
• Mangalore tiled roofs
• Corrugated AC sheet roofing, etc.
Application Procedure
Open the container apply it by brush or spray pump & allow it to dry for 24hr
Coverage: 50 to 70ft2 per lit ( depends on surface porosity of substrate)
Pack Size : 1lit,5lit,10lit & 20lit
WATER REPELLENT
Features & Benefits• Ease of application - Ready to use, simply brush able or spray applied.
• Staining - Clear coating does not stain the treated surface.
• Appearance - Does not change the appearance of exterior decorative coating.
• Vapor transmission - Prevents entry of moisture into the wall, but allows moisture to evaporate out.
• Efflorescence - Prevent efflorescence.
• Economical - Cost effective.
• Penetration – Due to low viscosity penetration is high, which provides the hydrophobic zone.