Connection and Protection for Comm-Data and CCTV Networks - Eric Sadler(2)

Connection and Protection for Comm/Data

and CCTV Networks

Eric SadlerPorta Systems Corporation

This training will discuss:

When and why Comm/Data protection is required

The magical devices that provide that protection

The features and benefits of each of these devices

The use of protection for data applications

The use of protectors, baluns, and protected baluns for CCTV networks over unshielded twisted pair (UTP)

Primary Protectionis the LAW!

Primary Protection

Required by the National Electric Code (NEC) Article 800.90 sec (A), enforced by building inspectors

Defined and Qualified by UL 497 and others

Primary Protection

Installed within 50 feet of the cable entrance to any building fed by:

Any aerial run of communications cable

Any cable buried for more than 140 feet

When you runoutside plant cable,

you needPrimary Protection!

Protection at the Campus Environment

CENTRAL

OFFICE Telco Demarc

Hospital

Labs

School

Dorms

P

Annexes

P

P

P

P

Main Switch

P

P= Surge Protection

P

P

P

P

P

P

The NEC requires Primary Protection to ensure that the

health and safety of equipment operators

is protected.

Protected from what?

There are 865,000 Lightning Strikes each day worldwide!

Lightning is the most common source of electrical disturbance to Telecom lines

A Power Cross is the transfer of excessive voltage and current by physical contact of an electrical power line with a communications

network

The second most common source of electrical disturbance is the

Power Cross

Typical Connected Building

Power Cross withTelephone Line

But it is often overlooked!

Primary Protection is a legal requirement and also makes

good business sense

Inspectors seldom check the installation of Comm/Data equipment for NEC compliance.

Contractors who submit their bid with protection are more expensive than those that submit a bid without it.

The problem with this, is that protection is very inexpensive when compared to Telecom equipment.

Whatever the property owner saves in up front costs by

not including protection, he will lose when his

equipment gets damaged!

Primary protection must contain:Surge arrestor modules in an entrance terminal

which contains 26 AWG fusible links

26 AWG Fusible Link

Surge Arrestor Module

24 AWG

PBX

22 AWG

Gas Tube (3B1E) Solid State (3B1S) Hybrid Any of these can contain overcurrent

protection as well (4B1E, 4B1S)

Common Types of Primary Protector Modules

Gas Tube Modules

Gas Tube

High energy Gas Discharge Tube dissipates surges as high as 10,000A

to ground.

Ceramic Insulator

Ceramic Insulator

3-Electrode Gas Tube Arrestor

Tip

Ring

Metal Electrode

Metal Electrode

Metal Electrode

Simultaneous short of both lines to ground

Proprietary Gas Mixture

Gas Tube Protectors UL 497 Listed Primary Protection Most economical Protects

the safety of equipment operators prevents fires in the building prevents damage to equipment from the

majority of surges Self-resetting; withstands 10,000 Amps for 10

microseconds

Solid State Modules

Solid State

Solid State Components

Thyristor shorts fast-rising-voltage surges to ground, or Diode that clamps these voltages until Gas Tube shorts them to ground.

Metal Electrode

Metal Electrode

Active Silicon Wafer

Surge goes to Gnd

Equipmentis protected

Conventional Solid State Transient Voltage Suppressor (TVS)

Solid State Protectors

Signal quality and activation energy do not deteriorate

Provide superior protection for sensitive equipment

Fast reaction time of less than 5 nanoseconds

Self-resetting; withstands 100 Amps for 10 microseconds

Protector Modules are Voltage-Sensitive Devices

You should always choose a protector module with a breakdown voltage as close to, but higher than the operating voltage of your equipment.

This typically means 230-240 volts for analog telephone lines.

75-volt modules for digital telephones that do not have analog ringing voltage

Low voltage (7.5-65 volts) for data applications we will discuss later

Protection from surges that do not have enough voltage to trip the over-voltage devices, but still have enough energy to damage equipment!

Modules that have in their generic part number a 4 such as 4B1E or 4B1S

To provide this type of protection, there are a variety of devices available.

Overcurrent Protection

Fuse

Positive Temperature Coefficient resistor

(PTC)

Heat Coil

Overcurrent Protection

Conventional fuseNewer

miniature fuse

Needleeye

Fuses

Fuses

Detect low levels of current

Require replacement after activation

Permanently open the circuit when excess current is detected (when the fuse has blown)

Positive Temperature Coefficient Resistors (PTC)

Polymer Based

Ceramic Based

PTCs

Basically, a self resetting fuse Hysteresis problems Close the circuit when reset, but

still have the open circuit at the most critical time: during the electrical disturbance!

Heat Coil

For Overcurrent Protection

Heats up if current is too high, then spring pushes contact forward,

grounding the circuit.

Heat Coil

Thimble

Cap & Dart

Heat CoilResistance wire is coiled around

thimble

Compressed spring urging cap forward

Low-melt temperature Solder Alloy

Heat Coil

Solder melts and spring pushes dart forward

When excess current flows, the resistance wire heats up

Dart contacts ground electrode and circuit is

permanently shorted to GND

Heat Coils

Detect low levels of current

Permanently short the line side to ground

Require replacement after activation

Why such acomplicated device?

Excellent slow-blo characteristics

Unlike PTCs and Fuses, Heat Coils ground the line instead of opening the circuit this reduces the potential for currents to jump

to other wires

Provides the best over-current protection for equipment fed with multi-pair cables

Primary Protection Modules fulfill one part of the requirement for Primary Protection:

Voltage Surge Suppression

To complete the requirement, one must have the second component:

A housing with a fusible link

A piece of thin wire located in the housing (BET) before the protector module field

Designed to open before any other wiring in the system

Without a fusible link, any wire in a communications system could burn open during a surge and cause a fire!

A fusible link is:

Building Entrance Terminals (BETs) and Protector Packs must meet or exceed these

requirements

Local distribution of cable in multi-tenant office buildings, high-rise apartments and campus environments

Splice Chamber physically protects and isolates incoming gel-filled cable

UL Listed for Primary and Secondary Protection

Available in 25, 50 and 100 Pair Vertically Stackable Available in a variety of terminations Optional cover over the protector

field

Splice Chambered BET

Local distribution of cable in multi-tenant office buildings, high-rise apartments and campus environments

Used when physical protection and isolation of incoming cable is not required

UL Listed for Primary and Secondary Protection

Available in 25, 50 and 100 Pair

Available in 66 and 110 terminations and cable-stub inputs

Economically priced

No Splice Chamber BET

Typical BET Installation

Primarily used to run from a Demarc or splice casing to a separate cross connect field.

Comes with 26 awg input Riser Rated Cable to provide fusible link

UL Listed for Primary and Secondary Protection

Available in 25, 50 and 100 Pair

Stub in Stub out BET

Small, light-weight BET for the termination and protection of incoming copper communication cables

Protects electronic telephone systems, particularly PBXs and KSUs

UL Listed for Primary and Secondary Protection

Units may be cascaded for future growth

Available in 6, 12, and 25 pair counts

Choice of 66 or 110 terminations

Can be used with any of the Protector Modules we discussed

Protector Packs with Primary Protectors:

Protector Pack

(12 Pair)

Protector Pack

(6 Pair)

Rack-Mountable 300-pair BET, fits on standard 23 x 6 deep relay rack

Standard configuration is cable-stub input, 110, 66 or cable-stub output

All mounting hardware and wire management guides are included

UL Listed for Primary Protection

Highly customizable 1800-pair on a 7-ft. rack for protection

and cross connection 2400-pair on a 7-ft. rack for protection

only

Contact the manufacturer to customize an XLBET to your specifications

XLBET

The Primary Protection requirement applies to data systems the same

way it does for telephone systems!

Portable Classrooms Trailers at construction sites Equipment controlled remotely

using Industrial Ethernet

Outside Plant Category cable can carry data to:

How does one provide Primary Entrance

Protection to devices requiring CAT 5E

performance?

CAT5E Protector Blocksand Modules

Hubs / Concentrators, Routers Audio / Video Equipment Alarm Systems Control equipment such as PLCs IP anything!

Computers Phones Cameras

CAT5E rated Blocks and Modules are used to Protect Data Network and

other Low-Voltage Equipment, Including:

Protectors and Terminations provided in multiples of 4

32-pair on an 89 D mounting bracket

Comes with DIN-rail mounting hardware for industrial applications

Accepts CAT5E rated modules available in 7.5, 18, 27 and 65-volt models, similar in design to telephone modules.

UL Listed for Data/Alarm and Primary Protection

CAT5E Rated Blocks Features:

How does one provide Primary Entrance

Protection to devices requiring CAT6 performance?

CAT6 Rated Protector Blocksand Modules

Building Entrance protection that maintains the full functionality of CAT 6

With ultra-low capacitance, they provide protection that permits signals of frequencies up to 250 MHz

Standard 110 style terminations for inputs and outputs

CAT6 rated modules available in 18V, 27V or 65V

Provides an ideal solution for Power Over Ethernet (POE) when used with 65-volt modules

CAT6 Rated Protector BlocksFeatures and Benefits:

CAT5E and CAT6 modules are for low-voltage data applications only!

If someone is putting telephone signal on CAT5E or

CAT6 cable, they must use one of the telephone protector modules discussed earlier!

Important!

Broadband is distinct from other data applications!

Also Important!

Broadband signals such as T1, E1, xDSL and VDSL require protectors specific for those applications

Signal voltage can vary from 205 to 400 volts

Most xDSL are best protected by modules with silicon based semiconductors specially designed to have low capacitance (~20 pF)

T1, E1, and VDSL are best protected by a hybrid gas tube/ Metallic Oxide Varistor (MOV), a metallic based semiconductor that reacts nearly as quickly as silicon based semiconductors, but have ultra-low capacitance (~5 pF)

Coaxial Cable

Unshielded Twisted Pair (UTP)

Protection plays a role in CCTV applications that run

over copper wires

For Installations that use Coaxial Cable, there are coaxial

Protectors available (BNC to BNC)

Coaxial Protector

Installed in front of cameras and/or recording devices Standing wave ratio 1.2:1 Low Pass 20 Hz - 40 MHz Insertion Loss -

UTP is less expensive than Coaxial Cable UTP is less bulky and easier to install UTP can run for longer distances, 1000-2000 feet easily

compared to 600 feet for Coax Many times structured cabling is already in place and one

can use the existing UTP to run the CCTV network Allows easy upgrade to IP cameras on UTP of CAT5E or

better.

The Modern trend is to run CCTV networks over UTP. Why?

For UTP Installations, there are protectors specifically for the

application of cameras over UTP

UTP Protectors

Single and double Channel Multi-function protector Supports camera control signals RS422 and RS485 over UTP, as well

as camera signal and power Compact Design

UTP Protectors

Video Baluns

The devices that permit the transmission of video signals over UTP Mini versions fit inside camera housings Amplified versions or Active Baluns permit transmission over

greater distances Models available both with and without surge protection

Video Baluns Active Video Balun

Video Combiners

Provide for the combination of video signal, power and control for PTZ cameras over UTP

Connectorized (RJ45) or with 110 terminations Passive device no power required Can pass power through them to power the camera

Video Combiners

Video Combiners with Protection

Provide the combination of video, power and control for PTZ cameras over UTP or a combination of UTP and coaxial cable

Provides protection form surges Passive device no power required Can pass power through them to power the camera

Combiners with Protection

Slide Number 1This training will discuss:Primary Protection is the LAW!Primary ProtectionPrimary ProtectionWhen you runoutside plant cable, you need Primary Protection!Slide Number 7The NEC requires Primary Protection to ensure that the health and safety of equipment operators is protected.Protected from what?Slide Number 10Slide Number 11Slide Number 12Slide Number 13Slide Number 14Slide Number 15Slide Number 16Slide Number 17Slide Number 18Slide Number 19 Gas Tube ModulesGas Tube3-Electrode Gas Tube ArrestorGas Tube Protectors Solid State ModulesSolid StateConventional Solid State Transient Voltage Suppressor (TVS)Solid State ProtectorsProtector Modules are Voltage-Sensitive Devices Overcurrent Protection Overcurrent ProtectionFusesSlide Number 32Slide Number 33PTCsHeat CoilHeat CoilHeat CoilHeat CoilHeat CoilsWhy such acomplicated device?The Hybrid Protector ModuleSlide Number 42Slide Number 43Building Entrance Terminals (BETs) and Protector Packs must meet or exceed these requirements Slide Number 45Slide Number 46Typical BET InstallationSlide Number 48Slide Number 49Slide Number 50The Primary Protection requirement applies to data systems the same way it does for telephone systems!Slide Number 52How does one provide Primary Entrance Protection to devices requiring CAT 5E performance?Slide Number 54Slide Number 55Slide Number 56How does one provide Primary Entrance Protection to devices requiring CAT6 performance?Slide Number 58Slide Number 59Slide Number 60Slide Number 61Slide Number 62For Installations that use Coaxial Cable, there are coaxial Protectors available (BNC to BNC)Coaxial ProtectorSlide Number 65For UTP Installations, there are protectors specifically for the application of cameras over UTPUTP ProtectorsVideo BalunsVideo CombinersVideo Combiners with ProtectionMulti-Channel ProtectorsModular Rack Mountable Components with ProtectionModular Rack Mountable Components with ProtectionFor IP Camera Installations, you would use the CAT5E or CAT6 protectors we discussed previously, because IP Cameras are Ethernet applications!All of the devices we discussed today that provide surge protection for Telephone, Data, and Security networks are nothing more than ugly wall decorations with out a proper connection to ground!References for appropriate connections to ground:Slide Number 77Slide Number 78Slide Number 79