Đây là bài lab ở cấp đô cao cấp dành cho nhưng ai học CCNP....Đã là pro thì không còn dùng Tiềng Việt nữa nhé ...English tí xíu cho oách nha.. ....la..la...lá...la..la..ta vô đề nào... Introduction Cable the network as shown in the diagram In this lab you will implement several switching technologies. Use 172.16.x.x/24 as the IP addressing scheme. Topology as below: The following tasks must be achieved: 1. Configure the DLSwitch as the VTP servers, VTP domain vnpro, and all other switches as VTP clients. 2. Spanning-Tree must be configured to designate the Distribution layer switch as the primary root bridge for all configured VLANs. 3. The network must utilize EIGRP as the routing protocol.
17
Embed
Configure Routing Inter Vlans Stp Trunking Vtp Nat
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Đây là bài lab ở cấp đô cao cấp dành cho nhưng ai học CCNP....Đã là pro thì không còn dùng
Tiềng Việt nữa nhé ...English tí xíu cho oách nha..
....la..la...lá...la..la..ta vô đề nào...
IntroductionCable the network as shown in the diagramIn this lab you will implement several switching technologies. Use 172.16.x.x/24 as the IP addressing scheme.
Topology as below:
The following tasks must be achieved:
1. Configure the DLSwitch as the VTP servers, VTP domain vnpro, and all other switches as VTP clients.2. Spanning-Tree must be configured to designate the Distribution layer switch as the primary root bridge for all configured VLANs. 3. The network must utilize EIGRP as the routing protocol.4. Enable Telnet with the password “cisco” on all devices for remote management. 5. Your organization is given the IP address range 200.200.200.18/24 to 200.200.200.30/24. Configure NAT on the border router to provide Internet access to all internal hosts.
6. Use network 172.16.1.0/24 for VLAN 1.7. Configure FEC between the Access layer and Distribution layer switches.Các bước thực hiện :
1. Cấu hình DLSwitch là VTP mode server, VTP domain vnpro, các Switch khác là mode client. Tạo 3 VLAN 10, 20, 30 với tên tương ứng Accounting, Marketing, Engineering trên DLSwitch.
6. Gán các port cho từng VLAN tương ứng trên các ALSWITCH1, ALSWITCH2, ALSWITC3 Mặc định các port trên Switch thuộc về VL AN 1 nên ta không cần gán port cho VLAN
ALSWITCH1(config)#interface range fas0/4 –6ALSWITCH1(config-if)#switchport access vlan 0ALSWITCH1(config)#extALSWITCH1(config)#interface range fas0/7 –9ALSWITCH1(config-if)#switchport access vlan 0ALSWITCH1(config)#extALSWITCH1(config)#interface range fas0/10 – 2ALSWITCH1(config-if)#switchport access vlan1ALSWITCH1(config)#ex
Làm tương tự trên 2 Switch còn lại (ALSWITCH2, ALSWITCH
Kiểm tra xem các port đã được gán đúng VLAN trên ALSWITCH1
7. Cấu hình trunking trên port Fastethernet 0/24 của DLSWITCH và CLSWITC
Để các traffic đi ra Internet router chúng ta phải thực hiện route tĩnh, ngoài ra trong mode router eigrp ta cũng quảng bá route tĩnh này để các router cũng chạy eigrp khác thấy được
INTERNET_ROUTER(config)#ip nat inside source list 1 interface Fast0/0 overloadINTERNET_ROUTER(config)#access-list 1 permit any
Mục đích thiết lập NAT ở đây là để cho ra Internet
INTERNET_ROUTER(config)#interface Fas0/0INTERNET_ROUTER(config-if)#ip address dhcp //Xin địa chỉ IP từ DHCP ServerINTERNET_ROUTER(config-if)#ip nat outsideINTERNET_ROUTER(config-if)#no shut
Tiếp theo phải cấu hình route tĩnh để ra Internet thông qua default gateway của internet la 192.168.1.1 và route tĩnh về địa chỉ NAT ra ngoài là 200.200.200.0(từ dãy địa chỉ 200.200.200.18-200.200.200.30)