www.commercial-solutions.net B.R. FUNSTEN & CO. WHOLESALE FLOORING PRODUCTS TOM DUFFY COMPANY WHOLESALE FLOORING PRODUCTS SEAMLESS INSTALLATION VPI offers 13 seam welding bead colors when seamless floors are required. VPI can also provide 24” & 36” tile pre-grooved for easy seam welding on site. Rose 905 Light Brown 904 Light Blue 909 Black 901 White 902 Rust 924 Sandstone 913 VINYL ESD 10 Black Ice 21 Rain Forest 09 Glacier 17 Platinum 52 Winter White 92 Patriot 53 Bone 16 Cloud 02 White 30 Eggplant 93 Storm CONDUCTIVEANDSTATMATECOLORS Dark Brown 914 Off White 912 Jade 918 Gray 906 Light Gray 916 Dark Gray 915 PERFORMANCE PROPERTIES • ESD STATIC CONTROL TILE CONDUCTILE FLOORING GAUGE (thickness) SIZE (in inches) COMPOSITION ANSI ESD S7.1 Resistance of Flooring Materials Conductile© used in conjunction with VPI adhesives very consistently meets S7.1 requirements. Result averages are summarized as follows: Resistance (Ohms) Conductile & VPI 165 Adhesive, to Ground 2.1 X 105 Conductile & VPI 165 Adhesive, Point to Point 3.5 X 105 Conductile & VPI 150 Adhesive, to Ground 3.9 X 105 Conductile & VPI 150 Adhesive, Point to Point 5.8 X 105 Data demonstrates that Conductile© used in conjunction with VPI adhesives very consistently meets S7.1 requirements for a conductive ESD flooring. (Test data available upon request). NFPA 99 Standard for Health Care Facilities NFPA 101 Life Safety Code AATCC 134 Electrostatic Propensity ANSI/UL 779 Electrically Conductive Floor Covering ASTM E84 Fire Resistance (Steiner Tunnel) FED STD 101C Static Decay, Method 4046 at 15% RH ASTM E648 Critical Radiant Flux CRF (W/cm2) ASTM F150 Electrical Resistance ASTM F925 Chemical Resistance ASTM F970 Static Load ASTM F1700 Solid Vinyl Floor Covering Materials VPI 150 2 Part Epoxy Adhesive 0 VOC Content Adhesive and Spread Rate Nominally 135 Sq.ft/gal but will vary due to application & substrate variables VPI 165 1 Part Acrylic Adhesive 0 VOC Content Nominally 135 Sq.ft/gal but will vary due to application & substrate variables Trowel Size Please refer to Installation & Maintenance Instructions 25 year wear / 75 year workmanship & materials No wax required. WARRANTY (See actual VPI WARRANTY for details) MAINTENANCE (See Installation & Maintenance Instructions for details) Electrical Performance Life Time Warranty Grounding Materials Supplied with the Order One 2" x 24 " copper strip installed every 2,000 - 2,500 sq. ft. Meets UL Standards < 12 Volts with conductive shoes Passes Passes <.001" RI after 24hrs@ 250 psi (1.125" diameter foot) 2,500 psi @ .005" RI after 24 hrs (.05" diameter foot) Excellent (Acids, Alkalis, Household, Chemicals) Point to Point or Point to Ground 25,000 - 1,000,000 ohms >1.08 W/cm2 (NFPA 253 Class 1) 1/8" (3mm) Homogeneous solid vinyl tile with encapsulated conductive elements distributed throughout the structure. Conforms 5000 - 0 Volts in < 0.01 Sec. <75 (Class II) 12" x 12" 24" x 24" and 36" x 36" 24" x 24" and 36" x 36" can be pre-grooved for seamless floor VPI 150 A two part epoxy adhesive specially engineered for use below grade (porous or non-porous) and /or with heavy load traffic or heavy static loads such as hospital beds. Depending on conditions and application, spread rate is nominally 135 square feet. RH requirements are a maximum of 85% and a PH of 6 - 9. See adhesive section for more details including substrate requirements and open times. Zero detectable VOC’s. GAUGE (thickness) SIZE (in inches) COMPOSITION ANSI ESD S7.1 Resistance of Flooring Materials Point to Point or Point to Ground 1,000,000 - 1,000,000,000 ohms NFPA 99 Standard for Health Care Facilities NFPA 101 Life Safety Code AATCC 134 Electrostatic Propensity ANSI/UL 779 Electrically Conductive Floor Covering ASTM E84 Fire Resistance (Steiner Tunnel) FED STD 101C Static Decay, Method 4046 at 15% RH ASTM E648 Critical Radiant Flux CRF (W/cm2) ASTM F150 Electrical Resistance ASTM F925 Chemical Resistance ASTM F970 Static Load ASTM F-1700 Solid Vinyl Floor Covering Materials VPI 150 2 Part Epoxy Adhesive 0 VOC Content Adhesive and Spread Rate Nominally 135 Sq.ft/gal but will vary due to application & substrate variables VPI 165 1 Part Acrylic Adhesive 0 VOC Content Nominally 135 Sq.ft/gal but will vary due to application & substrate variables Trowel Size Please refer to Installation & Maintenance Instructions 25 year wear / 75 year workmanship & materials No wax required. 1/8" (3mm) Homogeneous solid vinyl tile with encapsulated conductive elements distributed throughout the structure. Conforms 5000 - 0 Volts in < 0.20 Sec. <75 (Class II) 12" x 12" 24" x 24" and 36" x 36" 24" x 24" and 36" x 36" can be pre-grooved for seamless floor Meets UL Standards < 30 Volts with conductive shoes Passes Passes <.001" RI after 24hrs@ 250 psi (1.125" diameter foot) 2,500 psi @ .005" RI after 24 hrs (.05" diameter foot) Excellent (Acids, Alkalis, Household, Chemicals) Point to Point or Point to Ground 1,000,000 - 1,000,000,000 ohms >1.08 W/cm2 (NFPA 253 Class 1) WARRANTY (See actual VPI WARRANTY for details) MAINTENANCE (See Installation & Maintenance Instructions for details) Electrical Performance Life Time Warranty Grounding Materials Supplied with the Order One 2" x 24 " copper strip installed every 2,000 - 2,500 sq. ft. PERFORMANCE PROPERTIES • ESD STATIC CONTROL TILE STATMATE FLOORING VPI 165 A simple to use one part adhesive for use on or above grade. Can be used on porous or nonporous substrates in applications with light to medium traffic. Depending on conditions and application, spread rate is nominally 135 square feet. RH requirements are a maximum of 85% and a PH of 7 - 11. See adhesive section for more details including substrat requirements and open times. Zero detectable VOC’s. All items available in: 12” x 12” • 24” x 24” • 36” x 36” sizes