Computer SMART III FAST REGULADOR DE ENERGÍA REACTIVA REACTIVE ENERGY REGULATOR GUÍA DE PROGRAMACIÓN PROGRAMATION GUIDE Los reguladores Computer SMART III FAST 6 / SMART III FAST 12, miden el cosφ de red y regulan la conexión y desconexión de condensadores para corregirlo. Además, calculan y visualizan los principales parámetros eléctricos en redes monofásicas, trifásicas equilibradas o desequilibradas. Este manual es una guía de programación y puesta en servicio del Computer SMART III FAST. Para más información, se puede descargar el manual completo en la página web de CIRCUTOR: www.circutor.com The Computer Smart III FAST 6 / Smart III FAST 12 regulator measures the power grid cosine and controls capacitor connection and disconnection in order to correct it. It also calculates and displays the main electrical parameters of balanced or unbalanced single-phase and three-phase networks. This manual is a Computer SMART III FAST programation guide. For further information, please download the full manual from the CIRCUTOR web site: www.circutor.com Status of the capacitors Status of the unit Data area Analogue bar CPU Fan Alarm Key pressed Relación CT/CT Ratio (Ip / Is) Potencia en kvar del primer escalón a 400 V Power of the smallest stage at 400 V (kvar) 2.5 5.0 7.5 10.0 12.5 15.0 20.0 25.0 30.0 40.0 50.0 60.0 75.0 80.0 150/5 0.12 0.24 0.36 0.48 0.60 0.72 0.96 200/5 0.09 0.18 0.27 0.36 0.45 0.54 0.72 0.90 250/5 0.07 0.14 0.22 0.29 0.36 0.43 0.58 0.72 0.87 300/5 0.06 0.12 0.18 0.24 0.30 0.36 0.48 0.60 0.72 0.96 400/5 0.05 0.09 0.14 0.18 0.23 0.24 0.36 0.48 0.58 0.72 0.87 500/5 0.07 0.11 0.14 0.18 0.22 0.29 0.36 0.45 0.54 0.72 0.87 600/5 0.06 0.09 0.12 0.15 0.18 0.24 0.30 0.36 0.48 0.60 0.72 0.90 0.96 800/5 0.07 0.09 0.11 0.14 0.18 0.23 0.27 0.36 0.45 0.54 0.68 0.72 1000/5 0.05 0.07 0.09 0.11 0.14 0.18 0.22 0.29 0.36 0.43 0.54 0.57 1500/5 0.05 0.06 0.07 0.10 0.12 0.14 0.19 0.24 0.29 0.36 0.38 2000/5 0.05 0.07 0.09 0.11 0.14 0.18 0.22 0.27 0.28 2500/5 0.06 0.07 0.09 0.12 0.14 0.17 0.22 0.23 3000/5 0.05 0.06 0.07 0.10 0.12 0.14 0.18 0.19 4000/5 0.05 0.07 0.09 0.11 0.14 0.14 Funciones del teclado / Keyboard functions Indicadores en pantalla / Display Indicators Cálculo del Factor C/K / Calculating the C/K Factor Para tensiones diferentes de 400 V, el resultado de la tabla debe multiplicarse por 400/V, o calcular el parámetro C/K siguiendo las expresiones mostradas. For other voltages or conditions not included in the table, the value of C/K can be obtained by means of a simple calculation. Tecla / Key Pulsación corta / Short keystroke Pulsación larga / Long keystroke (3s) Pantalla anterior / Previous screen - Pantalla siguiente / Next screen. - Visualización valor mínimo Display of minimum value Borrado del valor mínimo Erase of minimum value Visualización valor máximo Display of maximum value Borrado del valor máximo Erase of maximum value Parámetro siguiente Next parameter Menú de programación Setup menu Pulsación muy larga (10 s) / Very Long keystroke (10 s): Entra en las pantalla de Test / Enter Test screens Tecla / Key Pulsación corta / Short keystroke Pulsación larga / Long keystroke (3s) Pantalla anterior / Previous screen Test: Conexión manual del con- densador seleccionado / Manual connects the displayed transformer Pantalla siguiente / Next screen. Test: Desconexión manual del con- densador seleccionado / Manual disconnects the displayed transformer Visualización valor mínimo Display of minimum value - Visualización valor máximo Display of maximum value - Parámetro siguiente Next parameter Test: Anular el proceso de AutoTest Cancel the AutoTest Pulsación muy larga (10 s) / Very Long keystroke (10 s): Entra en las pantalla de Test / Enter Test screens Tecla / Key Pulsación corta / Short keystroke Incrementa el valor o muestra la siguiente opción Increases the digit value or shows the next option Disminuye el valor o muestra la opción anterior Reduces the digit value or shows the previous option Parámetro de configuración siguiente / Skips to the next digit Parámetro de configuración anterior / Skips to the previous digit Entrada/Salida del modo edición / Enter/ Output edit mode Pantallas de configuración y test, modo consulta Displays configuration and testing, check mode Pantallas de configuración y test, modo edición Displays configuration and testing, edit mode Pantallas de medida / Measuring displays Tabla C/K / Table C/K Factor Tecla / Key El equipo se encuentra en modo de medida y regulación The unit is in measurement and regulation mode El equipo no mide ni regula The unit does not measure or regulate Indica que se está dentro del menú de configuración Indicates that you are in the setup menu Indica que se está dentro del menú de test Indicates that you are in the test menu. Indica que dentro del menú de configuración se está en modo edición Indicates that, within the setup menu, you are in edit mode Cálculo del C/K Relación del transformador de corriente (TC) It= Intensidad de primario de TC. K= It 5 Ic= Intensidad del primer condensador V . Q C I 3 = Cálculo C/K K I K C C = / Ejemplo: Relación del TC= 500/5 1er condensador: 60 kvar; 400V 1. 100 5 / 500 = = K 2. I C 400 3 60000 ⋅ = 3. C/K = = 0,867 86,7 100 Calculating the C/K factor Relation of the current transformer (CT) It= CT primary current Ic= The smallest transformer current V . Q C I 3 = K= It 5 Calculating the C/K K I K C C = / Example: Relation of the TC= 500/5 1st transformer: 60 kvar; 400V 1. 100 5 / 500 = = K 2. I C 400 3 60000 ⋅ = 3. C/K = = 0,867 86,7 100
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Computer SMART III FAST
REGULADOR DE ENERGÍA REACTIVAREACTIVE ENERGY REGULATOR
GUÍA DE PROGRAMACIÓNPROGRAMATION GUIDE
Los reguladores Computer SMART III FAST 6 / SMART III FAST 12, miden el cosφ de red y regulan la conexión y desconexión de
condensadores para corregirlo. Además, calculan y visualizan los
principales parámetros eléctricos en redes monofásicas, trifásicas
equilibradas o desequilibradas.
Este manual es una guía de programación y puesta en servicio
del Computer SMART III FAST. Para más información, se puede
descargar el manual completo en la página web de CIRCUTOR:
www.circutor.com
The Computer Smart III FAST 6 / Smart III FAST 12 regulator
measures the power grid cosine and controls capacitor connection
and disconnection in order to correct it. It also calculates and
displays the main electrical parameters of balanced or unbalanced
single-phase and three-phase networks.
This manual is a Computer SMART III FAST programation guide.
For further information, please download the full manual from the
CIRCUTOR web site:
www.circutor.com
Status of thecapacitors
Status of theunit
Data area
Analogue bar
CPU
Fan
Alarm
Key pressed
Relación CT/CT Ratio
(Ip / Is)
Potencia en kvar del primer escalón a 400 V Power of the smallest stage at 400 V (kvar)
Cálculo del Factor C/K / Calculating the C/K Factor
Para tensiones diferentes de 400 V, el resultado de la tabla debe multiplicarse por 400/V, o calcular el parámetro C/K siguiendo las expresiones mostradas.For other voltages or conditions not included in the table, the value of C/K can be obtained by means of a simple calculation.
Tecla / Key Pulsación corta / Short keystroke Pulsación larga / Long keystroke (3s)
Pantalla anterior / Previous screen -
Pantalla siguiente / Next screen. -
Visualización valor mínimo Display of minimum value
Borrado del valor mínimo Erase of minimum value
Visualización valor máximo Display of maximum value
Borrado del valor máximo Erase of maximum value
Parámetro siguiente
Next parameterMenú de programación
Setup menu
Pulsación muy larga (10 s) / Very Long keystroke (10 s):
Entra en las pantalla de Test / Enter Test screens
Tecla / Key Pulsación corta / Short keystroke Pulsación larga / Long keystroke (3s)
Ayuda a configurar automá�camente en el equipo los parámetros básicos para su regulación.Estos parámetros se pueden ajustar manualmente en las siguientes pantallas de configuración.
Configurar el valor de primario y secundario del transformador de corriente
Ver Ajuste de valores
Configurar 1er cos ϕ obje�vo . Consultar el manual completo para activar el
resto de cos ϕ mediante las entradas digitales (opcional).
Configurar los �empos de actuación del equipo en segundos
Seleccionar el �po de conexión de la instalación
Seleccionar la correcta secuencia de fase
Seleccionar el número de escalones, es decir el número de salidas de relé que tendrá el equipo
Determinar la secuencia de escalones con dis�ntas potencias .
Ajustar según la corriente reac�va aportada por el escalón más pequeño, medida en el
secundario del transformador de corriente
“t.on” es el �empo mínimo entre la conexión o la desconexión entre dos escalones.
“t.rec” es el �empo mínimo entre la desconexión y la conexión de un mismo escalón.
Recomendación*: t.on = 10 t.rec = 50(“t.rec” debe ser 5 veces mayor que “t.on”)
Ver sección de cálculo del factor C/K, en esta guía
(o si no tocamos ninguna tecla durante 5 minutos)
Valor entre 0.5 y 1* Recomendación : cos ϕ = 1
3U3C, 3 tensiones (con o sin neutro) y 3 corrientes. - 3U1C, 3 tensiones (con o sin neutro) y 1 corriente.
- 2U1C, 2 tensiones (entre fases) y 1 corriente.
Ejemplo: Programa 1.1.1.1, todos los escalones �enen la misma potencia que el primero.
Programa 1.2.4.4, el 2º escalón �ene potencia doble y los sucesivos cuádruple que el primero
Podemos configurar 6, 12 o 14 salidas según modelo.
Primario valor máximo: 9999. Primario valor mínimo: 1.
Secundario valores posibles: 1 ó 5
Acceso al menú de configuración Acceso a las pantallas de medida
Si se ha seleccionado la conexión con 1 corriente (3U1C ó 2U1C) se puede seleccionar una de las 6 posibles fases que se indican en
el manual completo .Si se ha seleccionado la conexión con 3 corrientes ( 3u3C) se asocia cada corriente con su tensión y se indica el sen�do de la corriente
d : directa. i : inversa.
OFF START
(pulsación corta)
Ajuste de valores y opciones en las pantallas de configuración
:
(Password correcto)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
Validar(pulsación corta)
Validar(pulsación corta)
Validar(pulsación corta)
Validar( pulsación corta)
Validar(pulsación corta)
Validar(pulsación corta)
Validar(pulsación corta)
Validar(pulsación corta)
Pantalla que muestra:- Medida del cos ϕ- Potencia reac�va trifásica- Pasos a conectar
Efectua la conexión de los pasos indicados previamente en la pantalla de simulación.
Pantallas de configuración:
.
Ver Ajuste de valores
Ver Ajuste de valores
Ver Ajuste de valores
Ver Ajuste de valores
Ver Ajuste de valores
Ver Ajuste de valores
Ver Ajuste de valores
Setup AvanzadoAcceder a pantallas de configuración avanzadas, a con�nuación de las pantallas de configuración
básicas. Para el setup avanzado consultar el manual completo
(pulsación corta)
(pulsación corta)Validar(pulsación corta)
Ver Ajuste de valores
* Valores recomendados por CIRCUTOR, revisar particularidades de la instalación, legislacio-nes y reglamentos particulares de cada país.
(”t.on” debe ser ≥ a “t.off”)
Validate( )
Measuring display
Password Secuency
Plug&Play
Current tranforma�on ra�o
Cos ϕ Target
Conec�on and reclosingn �me
Conec�on type
Num. stages
Program
C/K factor
Advanced Setup
Phase conec�on
Long keystroke (3s)
( short keystrokes )
( )
( )
( )
( )
( )
( )
( )
( )
( )
Any configura�ondisplay
Simula�on data
Start regula�on
(
Help to automa�cally configure the basic parameters for regula�on.These parameters can be set manually in the setup displays.
Set the value of primary and secondarycurrent transformer . See Setting of values.
Set 1st cos ϕ target. Check the full manual to activate
rest of cos ϕ via digital inputs(optional).
Set the �me in seconds of device ac�ons.
Select the connec�on type of installa�on.
Select the correct phase sequence.
Select the number of stages, number of relay outputs .
Set the steps sequency with different powers
Access advanced configura�on displays following basic configura�on displays
,
“t.on” is the minimal �me between the conec�on or disconec�on of two steps .
“t..
Recomendation*: t.on = 10 t.rec = 50(“t.rec” must be 5 times greater than “t.on”)
For advanced setup check the manual .
(or if we don’t play any key for 5 mins)
Value between 0.5 * Recomendation: cos ϕ = 1
- 3U3C, 3 voltages ( with or without neutral) and 3 currents. - 3U1C, 3 voltages ( ) and1 current.
- 2U1C, 2 voltages(between phases)
Example: Programe 1.1.1.1, all the stepshave the same power as the first .Programe 1.2.4.4, the 2nd step have doble po-wer and the rest, four �mes more that 1st .
We can set up 6, 12 or 14 outputs according to model
Primary maximum value: 9999. Primary minimum value: 1.
Secundary posibles values : 1 ó 5
Access the setup menu Access Measuring display
- If you select the connec�on with 1 current(3U1C ó 2U1C) youcan select one of the 6 posibles phases shown in the manual.
- If you select the connec�on with 3 currents ( 3u3C ) each current is associated with the voltage and current direc�on indicated.
d : direct. i : invers.
OFF START
( )
Setting of values and options in the configuration displays
:
( correct password )
(short keystroke)
( )
( )
( )
( )
( )
( )
( )
( )
( )
Validate( )
Validate( )
Validate( )
Validate( )
Validate( )
Validate( )
Validate( )
Validate( )
Validate( )
Display showing:- Measurement of cos ϕ- Reac�ve power phase- Steps to connect
Makes the connec�on of the previously men�oned steps in the simula�on display
Configura�ondisplay:
.
short keystroke
short keystroke
short keystroke
short keystrokeshort keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
Long keystroke (3s)
Long keystroke (3s) or if we don’t play any key for 5 mins)
See sec�on for calcula�ng C/K Factor
rec” is the minimal �me between the conec�on or disconec�on of same step
with or without neutraland1 curent.
See Setting of values
See Setting of values
See Setting of values
See Setting of values
See Setting of values
See Setting of values
See Setting of values
The C/K factor is adjusted according to the reac�ve current provided by the smallest stage,
measured in the secondary of the current transformer. See Setting of values
(”t.on” must be ≥ that “t.off”)
and 1
* Recommended values by CIRCUTOR, check the particularity of the own instalation, legislations and regulations in each country
Increases the digit value or shows the next option