Complete Catalog

REFERENCE GUIDED-FLEX Couplings Page PT1-2 Low-cost Type J couplings offered in four sizes Type S couplings feature AGMA 9 balanced anges off the shelf Type B couplings offered with standard QD bushing shaft attachment Type SC spacer couplings satisfy standard spacing requirements for pump Rounded EPDM and Neoprene elements for improved t and longer AGMA 9 balance on S and SC anges for reduced vibration Applications Interchangeable components make installation quick, easy No lubrication assures trouble-free operation

Gear Couplings Page PT1-52 High-quality forged steel Largest tooth prole provides additional service factor Largest bore capacity in the industry, in most sizes Proven O-ring seal design Machined anges for improved sealing High-grade fasteners High-torque rating allows for coupling downsizing Crowned tooth prole for longer life and improved performance Interchangeable with industry-standard gear couplings half for half

Chain Couplings Page PT1-57 Simple, widely accepted, inexpensive way to couple two shafts Interchangeable with industrystandard dimensions Can be provided with TAPERLOCK bushed hubs, nished bore, or reboreable anges Covers and assemblies available from stock Shaft attachment exibility High-torque capability Compact design Low operating cost Broad product line

GRID-LIGN Couplings Page PT1-42 Flexible tapered element isolates vibration and cushions shock loads High-torque capability Interchangeability with other taper grid couplings Speed capability as high as 6000 RPM Tapered grid design

REFERENCE GUIDE-1

Fluid Couplings

Motor starts under no-load conditions Starting torque can be customized easily Permits use of standard NEMA design B motors Reduced voltage starters not needed Sizes 7 to 24 KSD with standard QD mounting sheave style Sizes 7 to 19 KSD use collect mounting for a wide range of KCP and CKCP mountings may require tapped motor shaft Available in standard and delay ll for increased control Optional fuse plug for overload protection Contact DODGE for non-standard sheaves

FLEXIDYNE

Torque transmitted through composite element system Finished-bore and TAPERLOCK ange designs Five-year limited warranty No lubrication and visual inspection reduces maintenance time Accommodates highest misalignment of any coupling in the industry 4 angular 1/8 parallel 5/16 end oat

Fluid Couplings Page PT4-1

Clutch and Brakes

PARA-FLEX Couplings Page PT1-14

Couplings

Gearing Quick Reference

Gearing Reference Guide Couplings Clutches and Brakes FLEXIDYNE Fluid Couplings

REFERENCE GUIDERigid Coupling Page PT 1-65 Metallic Coupling Requires no lubrication Taper-Lock Bushing allows for connection of two different shaft sizes 8 Flange Sizes thru 6 Bore Torque up to 254,500 in. lbs. Max RPM = 4965

Heavy Duty Drum Pulley Assemblies Page PT13-10 Standard, stock pulley assemblies t CEMA dimensions and exceed the CEMA application standards for use with conveyor belts rated up to 750 PIW/131 kN/m 14 taper bushings with the lowest installation stress of any taper bushing shaft mounting system for two hub pulley applications Up to 1" vulcanized 45, 60, and 70 durometer SBR and 45, 60, and 70 durometer Neoprene rubber lagged with plain and groove surfaces Vulcanized 60 durometer D-Lag with +73% more abrasion resistance that 60 durometer SBR Drums either center crowned or straight face

Ribbed Rigid Coupling Page PT1-66 Metallic Coupling Requires no lubrication Clearance Fit with Full Length Key Same shaft size required on both sides 34 Sizes thru 7 Bore Torque up to 404,000 in. lbs. Max RPM = 5360

Heavy Duty Wing Pulley Assemblies Page PT13-22 Standard, stock pulley assemblies t CEMA dimensions and exceed the CEMA application standards for use with conveyor belts rated up to 350 PIW/61 kN/m 14 taper bushings with the lowest installation stress of any taper bushing shaft mounting system for two hub pulley applications Slide-on 92 durometer urethane wing lagging 1/2 thick or 45, 60, and 70 durometer SBR, vulcanized directly to contact bars. Also weld-on strips with 45 and 60 durometer with prebonded SBR rubber lagging

Poly-Disc Coupling Page PT1-63 Requires no lubrication Taper-Lock Bushing allows for connection of two different shaft sizes Polyurethane Element Pin design cushions Shock Loads Excellent for Washdown Applications Wide Temperature Range (-90 to 170 Deg F) Misalignment = 2 deg.Angular, 1/32 in. parallel

MINE DUTY EXTRA Wing Pulley Assemblies Page PT13-28 Made to order based on conveyor load, belt tension, and belt wrap Designed for use with DODGE Mine Duty EXTRA drum pulleys One-piece integral hubs eliminate welded hub heat-affected zones (HAZ) 14 taper bushings with the lowest installation stress of any taper bushing shaft mounting system for two hub pulley applications Rugged wing-on-drum construction incorporating 2" x 3/4 thick contact bars, 3/8 thick wings, and 3/8 thick spacers Up to 1/2 vulcanized 45, 60, and 70 durometer SBR and 45, 60, and 70 Neoprene rubber lagging on contact bars Vulcanized 60 durometer D-Lag with +73% more abrasion resistance than 60 durometer SBR

FLEXIDYNE Couplings Page PT3-1 Motor starts under no-load conditions Permits use of STD NEMA-B motor Coupling or drive styles available 100% efcient, no slippage Can provide overload protection by slipping at loads somewhat greater than pre-set starting torque

REFERENCE GUIDE-2

REFERENCE GUIDEMINE DUTY EXTRA Drum Pulley Assemblies Page PT13-28 One-piece integral hubs eliminate welded hub heat-affected zones (HAZ) 14 taper bushings with the lowest installation stress of any taper bushing shaft mounting system for two hub pulley applications 360 welding of internal center disc Up to 1" vulcanized 45, 60, and 70 durometer SBR and 45, 60, and 70 durometer Neoprene rubber lagged with plain and groove surfaces Vulcanized 60 durometer D-Lag with +73% more abrasion resistance than 60 durometer SBR Drums either center crowned or straight face

Bushings Page PT6-1 Full line of TAPER-LOCK and QD available Stock sizes available up to 12" shaft diameter Material: sintered steel, cast iron, ductile iron, and stainless steel Easy installation and demounting Inch and metric bores

V-Belt Sheaves Page PT7-27 Full line of TAPER-LOCK and QD available Classical (A, B, and C) and D-V Wedge style (3V, 5V, and 8V) groove proles Stock sizes from one to 12 grooves and 2.65" to 71" in diameter Manufactured to MPTA standards MTO capabilitiesmaterial, construction, BTS, etc. Computer drive selection available

Engineered Drum Pulley Assemblies Page PT13-30 Made to order based upon conveyor load, belt tension, belt wrap angles, and bearing centers Supplied for belt ratings up to and exceeding 8000 PIW or 1400 kN/m Welded, integral, and T section super hub versions minimize the harmful effects of weld heat-affected zones (HAZ) 14 taper bushings with the lowest installation stress of any taper bushing shaft mounting system for two hub pulley applications up to 12" shaft diameter B-LOK keyless locking devices for shafts from 11" to 30" diameter

V-Belts Page PT7-28 Full range of Classical (A, B, and C) and D-V Wedge (3V, 5V, and 8V) belts Manufactured to RMA standards Poly-band, Double-V (hex), and FHP belts available Lengths from 22" to 660" Drive capability from 1 HP to over 1000 HP

Full line of TAPER-LOCK and QD available Steel material with rugged, compact designs Hubs to accommodate most bushing sizes Made-to-order capabilities special construction and materials

FHP Belt Drives Page PT8-10 Full range of FHP belts available Finished-bore and QT bushed style sheaves available QT bushings available in metric bores Cast iron and manufactured to MPTA standards Sheave outside diameter range: 1-1/2 to 19-3/4 Variable pitch sheaves available Computer drive selection available

REFERENCE GUIDE-3

Fluid Couplings

FLEXIDYNE

Weld-On Hubs Page PT6-12

Clutch and Brakes

Couplings

Gearing Quick Reference

Gearing Reference Guide Couplings Clutches and Brakes FLEXIDYNE Fluid Couplings

REFERENCE GUIDERoller Chain Drives Page PT12-2 Sprockets manufactured to ANSI standard TAPER-LOCK sprockets: #35 (3/8 pitch) to #160 (2" pitch) Double-strand, double-single, and re-boreable sprockets also available Special machining and re-bore capabilities Accessories available: chain casings, idlers, tensioners, etc. Hardened teeth up to 25 teeth on #40 through #160 sprockets Chain tools available

Clutch/Brake Modules Page PT2-12 Conforms to UL and CSA requirements One-piece, die-cast housing simplies mounting; housing nned for maximum heat dissipation Pre-lubricated and sealed ball bearings have higher B10 life rating than competitive modules High-torque, non-asbestos friction material assures long life and environmental safety Armatures incorporate a high-impact, high-temperature molded spline for heavy-torque and high-cycle capabilities DYNA-GAP automatic air gap mechanism automatically compensates for friction surface wear Modules are factory assembled, adjusted, and burnished for easy installation and out-of-the-box operation Rotor incorporates ball bearing and Driv-Lok key for foolproof installation Standard NEMA C-face and base mounted, shaft-in/shaft-out mounting congurations

HT Synchronous (Timing) Belt Drives Page PT11-2 Full line of TAPER-LOCK, QD, and minimum plain bore sprockets Higher capacity drives Available pitches: HT series, 5 mm, 8 mm, and 14 mm Made-to-order sprocket capabilities: construction, non-standard number of teeth, etc. HT200 belt proles Computer drive selection available

Torque Tamer Clutch Page PT2-19 Low cost overload protection Easy Set Adjustment = Adjustable slip-protection torque level Non asbestos friction discs Long Life Bushing Application Versatility: May be used with sprockets, gears, sheave, ange or other driven members.

D-Series Motor Brakes Page PT2-6 Exceptionally long-life friction material Internally rectied DC coil provides quieter operation Easy installation and external adjustment One moving part, reduces replacement parts Smooth stopping action Splined hub for superior load distribution Manual release

Shaft Mounted Clutches & Brakes Page PT2-19 Bore to Size and Taper Lock Bushings Voltage Input = 90, 24 and 6 VDC Static Torque Range: 22 lb-ft thru 175 lb-ft Factory Assembled, Adjusted, Burnished Dyna-Gap Self Adjusting Mechanism Heavy Duty Spline Driven Armature

REFERENCE GUIDE-4

CONTENTSDODGE Power Transmission Components CatalogCouplings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT1 Clutches and Brakes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT2 FLEXIDYNE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT3 Fluid Coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT4 TORQUE-TAMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT5 Bushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT6 V-Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT7 FHP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT8 Drive Component Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT9 DYNA-SYNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT10 HT Synchrous Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT11 Sprockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT12 Conveyor Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT13 Engineering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PT14

PT-1

CONTENTSCouplingsFeatures/Benets D-FLEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-2 PARA-FLEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-14 PARA-FLEX High Speed Flywheel. . . . . . . . . . . . . . . . . . . . . . . . . PT1-35 GRID-LIGN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-42 Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-52 Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-57 Specication How To Order Nomenclature D-FLEX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-4 PARA-FLEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-16 GRID-LIGN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-44 Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-54 Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-58 POLY-DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-63 Rigid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-63 Easy Selection D-FLEX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-5 PARA-FLEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-17 GRID-LIGN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-45 Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-59 Selection NY-LIGN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-41 Selection/Dimensions D-FLEX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-6 PARA-FLEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-18 High Speed, TAPER-LOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-36 GRID-LIGN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-46 Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-55 Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-60 POLY-DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-64 Rigid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-65 Modications/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-67 Engineering/Technical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT1-69 Part Number Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-1 Keyword Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX-29

PT1-1

Fluid Couplings

FLEXIDYNE

Clutches and Brakes

Couplings

PT Components Reference Guide

PT Components Reference Guide Couplings Clutches and Brakes FLEXIDYNE Fluid Couplings

FEATURES/BENEFITSD-FLEX Couplings FLEXIBLE SOLUTIONS LOW COST TYPE J COUPLINGS OFFERED IN FOUR SIZES Features zinc die-cast anges that are bored to size Accommodates applications through 10 HP at 1750 RPM Available with EPDM or Neoprene sleeves Shaft attachment with two setscrews at 65

TYPE S COUPLINGS FEATURE AGMA 9 BALANCED FLANGES OFF THE SHELF High-strength, cast iron anges that are nished bored for AGMA clearance t Offers plain bore for reboring Available with EPDM, Neoprene or Hytrel* sleeves Shaft attachment with two setscrews at 65

TYPE B COUPLINGS OFFERED WITH STANDARD QD BUSHING SHAFT ATTACHMENT Constructed from high-strength cast iron Available with EPDM or Neoprene sleeves

TYPE SC SPACER COUPLINGS SATISFY STANDARD SPACING REQUIREMENTS FOR PUMP APPLICATIONS Accommodates wide range of shaft spacing Features AGMA 9 balanced anges & drop-out center for easy equipment maintenance Available with EPDM, Neoprene or Hytrel sleeves Uses H & HS shaft hubs that are bored to size for slip t or offered with plain bore for reboring Shaft attachment with two setscrews at 65 Shaft hub ats are used for holding shafts stationary while loosening or tightening grade 8 bolts* Registered trademark of DuPont QD is a registered trademark of Emerson Electric Co.

PT1-2

FEATURES/BENEFITSD-FLEX Couplings ADDED VALUEOutside diameter concentric to bore for ease in alignment Rounded EPDM and Neoprene element edges for full tooth engagement, even load distribution, and reduced stress build up at edges

Two setscrews at 65 on Type J flanges, Type S flanges & type SC-H hubs for optimum shaft attachment. Holding force is 10% greater than two setscrews at 90

Type S and SC flanges are balanced to AGMA 9 specifications for reduced vibrationFLEXIDYNE Fluid Couplings

INTERCHANGEABLE COMPONENTS MAKE INSTALLATION QUICK, EASY Interchangeable with other elastometer sleeve couplings Slides into position for snug t

NO LUBRICATION ASSURES TROUBLE-FREE OPERATION No metal-to-metal contact Provides clean, quiet, trouble-free performance

PT1-3

Clutches and Brakes

Couplings


SPECIFICATION/HOW TO ORDER/NOMENCLATURED-FLEXSPECIFICATIOND-FLEX Couplings employ a molded, non-lubricated elastomeric flexing sleeve loaded in shear. The flexible sleeve shall be of EPDM, Neoprene, or Hytrel. The compound of EPDM shall be suitable for operation in ambient temperature from -30F to +275F, Neoprene 0F to +200F, and Hytrel -65F to +250F. Both EPDM and Neoprene sleeves shall have torsional flexing capability of 15 and accommodate 1 of angular misalignment. Hytrel sleeves, suitable to transmit four times the power of EPDM or Neoprene, has torsional flexing capability of 7 and 1/4 of angular misalignment. The flexible sleeve is connected with external and internal gear teeth that engage with mating teeth in each flange. The coupling assemblies have optional methods of attachment to the shaft including but not limited to: clearance fit or QD Bushings. Clearance fits are supplied with an industry standard keyway and two set screws, one over the key and one at 65. Spacer Couplings consist of two hubs and a center assembly consisting of two spacer hubs and one flexible element. The center assembly is readily removable to facilitate maintenance on pumps or other connected equipment and must be replaceable without disturbing the coupled equipment and without realignment.


HOW TO ORDERStandard couplings consist of: (2) Flange Assemblies (1) Flexible Sleeve Spacer Couplings consist of: (2) Shaft Hubs (2) Spacer Flanges (1) Flexible Sleeve

NOMENCLATURE6 JE / 2 - 6J X 7/8 SIZE SLEEVE (JE, JES, E,JN, JNS,N,H,HS) FLANGE QTY. FLANGE SIZE AND TYPE (J, S, B, SC-H) FLANGE B ORE

PT1-4

EASY SELECTIOND-FLEXDODGE PRESELECTED D-FLEX COUPLINGS FOR ELECTRIC MOTORS @ 1800 RPMD-FLEX D-FLEX D-FLEX TYPE J TYPE B QD BUSHED TYPE S SERVICE FACTOR SERVICE FACTOR SERVICE FACTOR SHAFTFRAME DIA. LIGHT MEDIUM HEAVY LIGHT MEDIUM HEAVY LIGHT MEDIUM HEAVY 1.0 1.5 2.0 1.0 1.5 2.0 1.0 1.5 2.0 143T 0.875 3J 3J 4J 6B 6B 6B 5S 5S 5S 145T 0.875 3J 4J 4J 6B 6B 6B 5S 5S 5S 145T 0.875 4J 4J 5J 6B 6B 6B 5S 5S 5S 182T 1.125 5J 5J 5J 6B 6B 6B 5S 5S 5S 184T 1.125 5J 6J 6J 6B 6B 6B 5S 6S 6S 213T 1.375 6J 6J * 8B 8B 8B 6S 6S 7S 215T 1.375 6J * * 8B 8B 8B 6S 7S 7S 254T 1.625 * * * 8B 8B 8B 7S 8S 8S 256T 1.625 * * * 8B 8B 9B 7S 8S 9S 284T 1.875 * * * 9B 9B 9B 8S 9S 9S 326T 1.875 * * * 9B 9B 10B 8S 9S 10S 286TS 1.625 * * * 8B 9B 10B 8S 9S 10S 324T 2.125 * * * 10B 10B 10B 9S 10S 10S 324TS 1.875 * * * 9B 10B 10B 9S 9S 10S 326T 2.125 * * * 10B 10B 11B 9S 10S 11S 326TS 1.875 * * * 9B 10B 11B 9S 10S 11S 364T 2.375 * * * 10B 11B 11B 10S 11S 11S 364TS 1.875 * * * 10B 11B 11B 10S 11S 11S 365T 2.375 * * * 10B 11B 12B 10S 11S 12S 365TS 1.875 * * * 10B 11B 12B 10S 11S 12S 404T 2.875 * * * 12B 12B 12B 11S 12S 12S 404TS 2.125 * * * 11B 12B 12B 11S 12S 12S 405T 2.875 * * * 12B 12B 13B 11S 12S 13S 405TS 2.125 * * * 11B 12B 13B 11S 12S 13S 444T 3.375 * * * 12B 12B 13B 11S 12S 13S 444TS 2.375 * * * 11B 12B 13B 11S 12S 13S 444/5T 3.375 * * * 12B 13B 13B 12S 13S 13S 444/5TS 2.375 * * * 12B 13B 13B 12S 13S 13S 444T 3.375 * * * 12B 13B 13B 12S 13S 14S 444TS 2.375 * * * 12B 13B 13B 12S 13S 14S MOTOR D-FLEX TYPE SC SERVICE FACTOR LIGHT MEDIUM HEAVY 1.0 1.5 2.0 5SC 5SC 5SC 5SC 5SC 5SC 5SC 5SC 5SC 5SC 5SC 5SC 5SC 6SC 6SC 6SC 6SC 6SC 6SC 7SC 7SC 7SC 8SC 8SC 7SC 8SC 9SC 8SC 9SC 9SC 8SC 9SC 10SC 8SC 9SC 10SC 9SC 10SC 10SC 9SC 10SC 10SC 9SC 10SC 11SC 9SC 10SC 11SC 10SC 11SC 11SC 10SC 11SC 11SC 10SC 11SC 12SC 10SC 11SC 12SC 11SC 12SC 12SC 11SC 12SC 12SC 11SC 12SC 13SC 11SC 12SC 13SC 11SC 12SC 13SC 11SC 12SC 13SC 12SC 13SC 13SC 12SC 13SC 13SC 12SC 13SC 14SC 12SC 13SC 14SC

H.P. 1 1.5 2 3 5 7.5 10 15 20 25 30 40 50 60 75 100

125

150 200

PT1-5

Fluid Couplings

FLEXIDYNE

Clutches and Brakes

Couplings



SELECTION/DIMENSIONSD-FLEX CouplingsFOUR-WAY FLEXING ACTION HANDLES SHOCK, VIBRATION & MISALIGNMENT

TORSIONALAbsorbs torsional shock, dampens torsional vibrations

ANGULARAbsorbs angular misalignment without water

PARALLELMinimizes radial bearing loads, absorbs parallel misalignment with less wear & energy loss

AXIALAllows for shaft end-float

D-FLEX COUPLING SLEEVESOne-Piece Solid Construction One-Piece Split Construction Two-Piece Construction Sizes Offered Temperature Range Max Angular Max Parallel(2) Axial End-Float Torsional Flexibility(2)(3)

EPDM RUBBER JE JES E 3 - 10 JE, JES 4 - 16 E -30F to +275F 1 010 -.062 .03 -.125 15 Wind Up

NEOPRENE JN JNS N 3 - 10 JN, JNS 4 - 14 N 0F to +200F 1 .010 -.062 .03 -.125

HYTREL(1) H HS 6 - 12 H, HS -65F to +250F 1/4 .010 -.035 .06 -.125 7 Wind Up Downsizing For Use Of Smaller Couplings

15 Wind Up Good Oil Application Use General Resistance (1) Do not use with J or B anges or as a replacement for other sleeves (2) Depends on coupling size. (3) Increase the E dimension by this amount to accommodate end oat.

FEATURES/BENEFITS PAGE PT1-2

EASY SELECTION PAGE PT1-5

MODIFICATION/ACCESSORIES PAGE PT1-67

ENGINEERING/TECHNICAL PAGE PT1-69

PT1-6

SELECTION/DIMENSIONSD-FLEX CouplingsD-FLEX COUPLING SLEEVES - PART NUMBERSCoupling Size 3 4 5 6 7 8 9 10 11 12 13 14 16 Stocked sleeves JE 004208 004210 004212 004214 004216 004218 004220 004222 EPDM JES 004242 004244 004246 004248 004250 004252 004254 004256 E 022190 022191 022192 022193 022194 022195 022196 022197 022198 021990 021991 021992 JN 004209 004211 004213 004215 004217 004219 Neoprene JNS 004243 004245 004247 004249 004251 004253 Hytrel N 022211 022212 022213 022214 022215 022216 022217 022218 022219 021993 021994 H HS

022183 022184 022185 022186 022187 022188 022189

022232 022233 022234 022235 022236 022237 022238

EPDM Flange Style Type J Type S Type B Bushed SC Spacer JE/JES 1 Piece E 2 Piece JN/JNS 1 Piece

Neoprene N 2 Piece H 1 Piece

Hytrel HS 2 Piece

D-FLEX SECTION/RATINGS DATAHP/100 2.90 4.60 7.20 11.40 18.00 28.60 50.00 75.00 115.00 FLEXIDYNE Fluid Couplings

Element Size 3 4 5 6 7 8 9 10 11 12 13 14 16

Max. Bore Straight Bore Type J 7/8 1 1-1/8 1-3/8 FEATURES/BENEFITS PAGE PT1-2

Bushed Type B 1-3/16 1-3/16 1-5/8 1-15/16 2-1/2 2-13/16 3-1/2 3-15/16 3-15/16 4-1/2

Type S 1-1/4 1-7/8 1-7/8 2-3/8 2-7/8 3-3/8 3-7/8 3-15/16 4-1/2 5 6

Type SC 1-1/8 1-3/8 1-5/8 1-7/8 2-1/8 2-3/8 2-7/8 2-7/8 3-3/8 3-7/8 -

Max RPM 9200 7600 7600 6000 5250 4500 3750 3600 3600 2800 2400 2200 1500

EPDM & Neoprene Rated HP/1000 Torque (In-Lbs) 0.10 60 0.19 120 0.38 240 0.71 450 1.20 725 1.80 1,135 2.80 1,800 4.60 2,875 7.20 4,530 11.40 7,200 18.00 11,350 28.60 18,000 75.00 47,250

Hytrel Rated Torque (In-Lbs) 1,800 2,875 4,530 7,200 11,350 18,000 31,500 47,268 72,480 -




PT1-7

Clutches and Brakes

D-FLEX FLANGE/SLEEVE COMPATIBILITY

Couplings



SELECTION/DIMENSIONSD-FLEX CouplingsTYPE J COUPLING DIMENSIONSB E

C

A

A

D

TO REMOVE SLEEVE

X

TYPE "J" FLANGE

TYPE "J" COUPLING

DIMENSIONSCoupling Size 3J 4J 5J 6J 6J Min. Bore 3/8 1/2 1/2 5/8 1-1/8 Max. Bore 7/8 1 1-1/8 1 1-3/8 HP/100 0.10 0.19 0.38 0.71 0.71 Torque (in.-lbs.) 60 120 240 4150 450 Max. RPM 9200 7600 7600 6000 6000 A 2.06 2.46 3.25 4.00 4.00 B 2.00 2.38 2.88 3.31 3.31 C 1.50 1.63 1.88 1.94 2.50 D 0.81 0.88 1.06 1.22 1.22 E 0.38 0.63 0.75 .88 0.88 X 0.56 0.75 0.97 1.09 1.09 Weight (lbs.) 0.3 .04 .09 1.4 1.2

PART NUMBERSBore (in.) 3/8 1/2 5/8 3/4 7/8 15/16 1 1-1/8 1-3/16 1-1/4 1-3/8 3J 022700 022701 022702 022703 022704 Coupling Flange 4J 5J 022708 022709 022710 022711 022712 022713 022714 022715 022716 022717 022718 022719 022720 6J

022721 022722 022723 022724 022725 022726 022727 022728 022729

Stock ange assemblies Complete coupling consists of (2) J anges, and (1) sleeve.FEATURES/BENEFITS PAGE PT1-2 EASY SELECTION PAGE PT1-5 MODIFICATION/ACCESSORIES PAGE PT1-67 ENGINEERING/TECHNICAL PAGE PT1-69

PT1-8

SELECTION/DIMENSIONSD-FLEX CouplingsTYPE B QD BUSHED COUPLING DIMENSIONSB E

C J

A

A

D

TO REMOVE SLEEVE

X

TYPE "B" FLANGE

TYPE "B" COUPLINGClutches and Brakes Fluid Couplings FLEXIDYNE

DIMENSIONSCoupling Bushing Size Type Min. Bore Max. HP/100* Bore# Torque* (in.lbs.) 450 725 1135 1800 2875 4530 7200 11350 18000 47250 Max. RPM A B 3.31 3.44 4.06 4.63 5.63 6.56 7.94 9.31 10.44 13.25 C 2.00 2.00 2.63 3.19 3.88 4.63 6.00 6.63 6.63 7.25 D 1.53 1.59 1.84 2.19 1.84 2.13 2.69 3.69 3.69 4.75 E 0.88 1.00 1.13 1.44 1.63 1.88 2.31 2.69 3.25 4.75 J 1.00 1.00 1.31 1.81 1.94 2.00 2.75 3.75 3.75 4.63 X 1.09 1.31 1.50 1.75 2.00 2.38 2.69 3.00 3.50 4.50 Weight (lbs.)+ BushFlange ing 1.30 0.40 1.90 0.40 2.90 0.90 4.80 1.60 7.80 2.70 12.00 3.80 18.00 9.00 31.20 14.00 51.40 14.00 120.00 21.00

6B JA 1/2 1-3/16 0.71 6000 4.00 7B JA 1/2 1-3/16 1.20 5250 4.63 8B SH 1/2 1-5/8 1.80 4500 5.45 9B SD 1/2 1-15/16 2.80 3750 6.35 10B SK 1/2 2-1/2 4.60 3600 7.50 11B SF 1/2 2-15/16 7.20 3600 8.63 12B E 7/8 3-1/2 11.40 2800 10.00 13B F 1 3-15/16 18.00 2400 11.75 14B F 1 3-15/16 28.60 2200 13.88 16B J 1-1/2 4-1/2 75.00 1500 18.88 # Max bore with shallow key * Ratings based on EPDM & Neoprene. For Hytrel ratings, see page PT1-7 + Approximate weight for each ange; average weight for each bushing

PART NUMBERSPart No. 6B 022501 7B 022502 8B 022503 9B 022504 10B 022505 11B 022506 12B 022507

Stock ange assemblies 13B 022508 14B 022509 16B 022510

Complete coupling consists of (2) B anges, (2) sleeve and (2) QD Busings. QD Busings must be ordered separately.

Part No.





PT1-9

Couplings



SELECTION/DIMENSIONSD-FLEX CouplingsTYPE S COUPLING DIMENSIONSB E

C

A

A

TO REMOVE SLEEVE D

X

TYPE "S" FLANGE

TYPE "S" COUPLING

DIMENSIONSCoupling Min. Max. Torque* Max. HP/100* A B Size Bore Bore# (in.-lbs.) RPM 5S 1/2 1-1/4 0.38 240 7600 3.25 2.81 6S 1/2 1-1/2 6S 1-9/16 1-3/4 0.71 450 6000 4.00 3.50 6S 1-13/16 1-7/8 7S 1/2 1-7/8 1.20 725 5250 4.63 3.94 8S 1/2 2-1/8 4.44 1.80 1135 4500 5.45 8S 2-3/16 2-3/8 5.00 9S 7/8 2-1/2 5.06 2.80 1800 3750 6.35 9S 2-9/16 2-7/8 6.00 10S 1-1/8 2-7/8 5.69 4.60 2875 3600 7.50 10S 2-15/16 3-3/8 7.00 11S 1-1/4 2-1/8 7.13 11S 2-3/16 2-3/4 7.13 7.20 4530 3600 8.63 11S 2-13/16 3-3/8 7.13 11S 3-7/16 3-7/8 8.00 12S 1-1/2 2-1/8 12S 2-3/16 2-7/8 11.40 7200 2800 10.00 8.25 12S 2-15/16 3-15/16 13S 2 Reb. 4-1/2 18.00 11350 2400 11.75 9.25 14S 2 Reb. 5 28.60 18000 2200 13.88 9.88 16S 2 Reb. 6 75.00 47250 1500 18.88 14.25 # Max bore with shallow keyway. For max bore with standard keyway, see page PT1-11 * Ratings based on EPDM & Neoprene. For Hytrel ratings, see page PT1-7FEATURES/BENEFITS PAGE PT1-2 EASY SELECTION PAGE PT1-5

C 1.88 2.50 2.50 2.81 2.81 3.25 3.63 4.13 4.38 4.75 5.63

D 1.34 1.63 1.31 1.56 1.84 2.09 1.94 2.41 2.28 2.72 2.69 3.44 3.44 3.44 3.88 4.00 4.38 4.50 6.00

E 0.75 0.88 1.00 1.13 1.44 1.63

X 0.97 1.09 1.31 1.50 1.75 2.00

1.88

2.38

5.75 6.75 7.50 8.00

2.31 2.69 3.25 4.75

2.69 3.06 3.50 4.25

Weight (lbs.) 1.10 1.90 1.80 1.80 2.60 4.40 3.70 6.50 6.20 10.50 9.80 18.10 17.90 16.60 16.40 27.80 27.50 26.60 45.20 69.10 125.30



PT1-10

SELECTION/DIMENSIONSD-FLEX CouplingsTYPE S COUPLING FLANGE - PART NUMBERSBore (in.) Reborable Finished Bore Flanges 1/2 5/8 3/4 7/8 15/16 1 1-1/8 1-3/16 1-1/4 1-5/16 1-3/8 1-7/16 1-1/2 1-5/8 1-11/16 1-3/4 1-7/8 1-15/16 2 2-1/8 2-3/16 2-1/4 2-3/8 2-7/16 2-1/2 2-5/8 2-11/16 2-3/4 2-7/8 2-15/16 3 3-1/8 3-1/4 3-5/16 3-3/8 3-7/16 3-1/2 3-5/8 3-11/16 3-3/4 3-7/8 3-15/16 METRIC 20mm 24mm 25mm 28mm 30mm 32mm 35mm 38mm 42mm 48mm 5S 004976 6S 004977 7S 004978 8S 004979 Coupling Flange Size 9S 10S 11S 004980 004981 004982 12S 004983 13S 004993 14S 004994 16S 004995

004694 004695

004696 004698 004699 004700 004702 004703 004704 004706 004707 004708 004710 004711 004712 004714 004715 004716 004718 004719 004720 004722 004724 004725 004726 004727 004728 004730 004731 004732 * 004734 004735

004996

004997

004998

004860 004862 004863

004869 004871 004872 004873 004874 004875 004876

Stock ange assemblies Max bore for reborable anges. Complete coupling consists of (2) S anges and (1) sleeve.

*Max bore with std. square keyway. Larger bores have rectangular keyways & keys supplied.





PT1-11

Fluid Couplings

004885 004886 004887 004888 004889 004890 004892

004901 004902 004903 004904 004905 004907 004909

004920 004921 004922 004923 004925 004927

FLEXIDYNE

Clutches and Brakes

Couplings

004498 004500 004502 004504 004505 004506 004508 * 004509 004510

004511 004534 004513 004536 004515 004538 004516 004539 004517 004540 004519 004542 004520 004543 004521 004544 004522 004545 004523 004546 * 004524 004547 004525 004548 004527 * 004550 004528 004551 004529 004552 004531 004554

004559 004561 004562 004563 004565 004566 004567 004568 004569 004570 004571 004573 004574 004575 004577 004578 * 004579 004581 004582 004583 004585

004586 004587 004588 004590 004619 004591 004620 004592 004621 004656 004593 004622 004657 004594 004623 004658 004595 004624 004659 004660 004596 004625 004598 004627 004662 004599 004628 004663 004600 004629 004664 004602 004631 004666 004603 004632 004667 004604 004633 004668 004606 004635 004670 004607 004636 004671 004608 004637 004672 * 004610 004639 004674 004611 004640 004675 004676 004612 004641 004614 004643 004678 004615 004644 004679 004616 * 004645 004680 004618 004647 004682 004648 004683 004649 004684 004651 004686 004653 004688 004654 004689 004655 * 004690 004691 004692 004693



SELECTION/DIMENSIONSD-FLEX CouplingsTYPE SC COUPLING DIMENSIONSF B E

A

C

C

A

TO REMOVE CENTER

K

SHAFT HUB

SPACER FLANGE

COMPLETE SPACER COUPLING

DIMENIONS (1)Shaft Hub Max. Bore (2) Flange A Number H HS H HS 3.50 5SC35 5H 1-1/8 3.25 3.50 6SC35 6H --1-3/8 6SC 4.38 6SC44 6H 1-3/8 4.00 5.00 6SC50 6H 1-3/8 3.50 7SC35 7H --1-5/8 7SC 4.38 7SC44 7H 1-5/8 4.63 5.00 7SC50 7H 1-5/8 3.50 8SC35 8H 1-7/8 3.50 8SC35-10 10H 10HS 2-3/8 1-5/8 4.38 8SC44 8H 1-7/8 8SC 5.45 5.00 8SC50 8H 1-7/8 5.00 8SC50-10 10H 10HS 2-3/8 1-5/8 3.50 9SC35 9H 9HS 2-1/8 1-1/2 4.38 9SC44 9H 9HS 2-1/8 1-1/2 5.00 9SC50 9H 9HS 2-1/8 1-1/2 9SC 6.35 5.00 9SC50-11 11H 11HS 2-7/8 1-7/8 7.00 9SC70-11 11H 11HS 2-7/8 1-7/8 7.75 9SC78-11 11H 11HS 2-7/8 1-7/8 4.75 10SC48 10H 10HS 2-3/8 1-5/8 5.00 10SC50 10H 10HS 2-3/8 1-5/8 7.00 10SC70-13 13H 13HS 3-3/8 2-1/2 10SC 7.50 7.75 10SC78-13 13H 13HS 3-3/8 2-1/2 10.00 10SC100-13 13H 13HS 3-3/8 2-1/2 4.75 11SC48 11H 11HS 2-7/8 1-7/8 5.00 11SC50 11H 11HS 2-7/8 1-7/8 7.00 11SC70-14 14H 3-7/8 11SC 8.63 7.75 11SC78-14 14H 3-7/8 10.00 11SC100-14 14H 3-7/8 7.00 12SC70 12H 12HS 2-7/8 2-1/2 7.00 12SC70-14 14H 3-7/8 7.75 12SC78 12H 12HS 2-7/8 2-1/2 12SC 10.00 7.75 12SC78-14 14H 3-7/8 10.00 12SC100-14 14H 3-7/8 13SC 7.75 13SC78 13H 13HS 3-3/8 2-1/2 11.75 14SC 7.75 14SC78 14H 3-7/8 13.88 (1) Ratings (HP/100, Torque, RPM) same as Type S. See page PT1-10. (2) Check shaft hub table on next page for minimum Bore. (3) B dimension included H hubs. Dimension will change if one or two HS (short hubs) are used. (4) Complete coupling weight at MAX bore. Cplg. Size 5SC BSEFEATURES/BENEFITS PAGE PT1-2 EASY SELECTION PAGE PT1-5

(3) B 5.63 5.88 6.75 7.88 6.38 7.25 7.88 6.88 9.13 7.75 8.38 9.63 7.50 8.25 8.88 10.38 12.38 13.13 9.38 9.63 13.63 14.63 16.63 10.31 10.38 14.38 15.38 17.63 12.88 14.63 13.63 14.38 17.63 14.38 15.38

C 2.00 2.50 2.50 2.50 2.81 2.81 2.81 3.25 4.38 3.25 3.25 4.38 3.63 3.63 3.63 5.25 5.25 5.25 4.38 4.38 6.13 6.13 6.13 5.25 5.25 6.50 6.50 6.50 5.75 6.50 5.75 6.50 6.50 6.13 6.50

E 0.75 0.88

F H 1.09 1.22 1.22 1.22 1.47 1.47 1.47 1.72 2.34 1.72 1.72 2.34 1.97 1.97 1.97 2.72 2.72 2.72 2.34 2.34 3.34 3.34 3.34 2.72 2.72 3.84 3.84 3.84 2.97 3.84 2.97 3.84 3.84 3.34 3.84 HS -

K 0.56 0.75

0.63 0.81 0.81 0.81 1.19 1.19 1.06 1.06 1.06 1.19 1.19 1.19 1.19 1.19 1.88 1.88 1.88 1.19 1.19 2.00 2.00 2.00 1.50 2.00 1.50 2.00 2.00 1.88 2.00

1.00

1.13

1.66 1.33 1.53 1.53 1.53 1.91 1.91 1.91 1.66 1.66 2.47 2.47 2.47 1.91

1.44

1.63

1.88

2.53

2.31

2.69 3.25

2.47 -

Wt. (4) (lbs.) 4.50 7.30 8.10 8.70 9.90 10.80 11.40 15.20 23.20 16.40 17.40 27.20 18.60 22.20 23.20 40.40 48.20 51.00 37.60 38.40 72.00 76.00 88.00 54.50 54.70 86.10 90.30 102.70 88.10 99.10 91.90 103.30 115.70 129.60 179.90



PT1-12

SELECTION/DIMENSIONSD-FLEX CouplingsTYPE SC SPACER COUPLINGS - SPACER FLANGE PART NUMBERSBSE (in.) 3.50 4.38 5.00 7.00 7.75 5SC 022000 6SC 022001 022002 022003 7SC 022004 022005 022006 Coupling Size 8SC 022007 022008 022009 8SC-10 9SC 9SC-11

022775 022776

022010 022011 022012

022777 022778 02277913SC 14SCCouplings

BSE 10SC (in.) 4.75 022013 5.00 022014 7.00 7.75 10.00 Stock anges Bore 5H (in.) Reborable Finished 022220 Bore Hubs 1/2 022329 5/8 022331 11/16 022332 3/4 022333 7/8 022335 15/16 022336 1 022337 1-1/8 022339 1-1/8 (1) 1-3/16 1-1/4 1-5/16 1-3/8 1-7/16 1-1/2 1-9/16 1-5/8 1-5/8 (1) 1-3/4 1-7/8 1-15/16 2 2-1/8 2-3/16 2-1/4 2-5/16 2-3/8 2-3/8(1) 2-7/16 2-1/2 2-5/8 2-11/16 2-3/4 2-7/8 3-3/8 3-7/8 Stock hub assembles

10SC-13

11SC 022015 022016

Coupling Size 11SC-14

12SC

12SC-14

022780 022781 022782

022783 022784 022785

022017 022018

022786 022787 022788

021997

021998

SPACER SHAFT HUB PART NUMBERS6H 7H 8H Coupling Size 9H 10H 11H 12H 13H 14H

022221022340 022341 022342 022344 022345 022346 022348 022349

022222022353 022354 022355 022357 022358 022359 022361 022362 022363 022364 022365

022223

022224

022225

022226

022227Clutches and Brakes

022368 022370 022371 022372 022374 022375 022376 022377 022378 022379 022380 022381 022382

022350022351 022352

022366 022367

022387 022388 022389 022391 022392(1) 022393 022394 022395 022396 022397 022398 022399 022400

022409

022410(1)022411 022412 022413 022414 022415 022416 022417 022418 022420

022384 022386

022402 022404022405 022406 022408

022428022429 022430 022432 022433 022434 022435 022436

0022452 022453(1) 022454 022455 022456 022457 022458 022459 022460 022461 022462(1) 022464 022466 022467 022468 022470 022471 022472 022473 022474 022475 022476 022478 022479 022480 022482

(1) HS (Short Hub)

022816 022817 022818 Complete coupling consists of (2) shaft hubs, (2) spacer anges, and (1) sleeveMODIFICATION/ACCESSORIES PAGE PT1-67 ENGINEERING/TECHNICAL PAGE PT1-69

022811 022812



PT1-13

Fluid Couplings

022483 022484 022485 022487 022488 022489 022490 022491 022492(1) 022493 022494 022496 022497 022498 022500

022813(1)

022810 022814(1)

022815

FLEXIDYNE



FEATURES/BENEFITSDODGE PARA-FLEX Couplings Finished Bore Flange Design Extra bore capacity Accommodates larger shaft diameters Allows for smaller coupling selection Two setscrews at 65 Precision alignment ats Ductile iron ange for clearance or interference ts

TAPER-LOCK Flange Design Reversible anges for H or F style mounting on sizes PX50-PX120 Uses standard TAPER-LOCK bushings for wide range of bores

Torque Transmitted Through Composite Element System Reinforced with torque-carrying tension cords Natural rubber or Neoprene Split end reinforcement Split element for easy installation Dampens torsional vibration

Five-Year Limited Warranty Dependable product performance 40+ years application experience Warranty includes sizes PX40 thru PX200

No Lubrication Less maintenance

Visual Inspection Saves time

PT1-14

FEATURES/BENEFITSFEWER LOOSE PARTS FOR EASY ASSEMBLY DODGE PARA-FLEX Standard Couplings DODGE PARA-FLEX Spacer Couplings

Install factoryassembled flanges (finished bore or TAPER-LOCK flanges)

Install shaft hubs (finished bore or TAPER-LOCK hubs)

Tighten clamp ring bolts by alternating every other bolt. Repeat sequence until tightened to recommended torque.

Tighten shaft hub bolts to recommended torqueFLEXIDYNE

Accommodates Misalignment

Takes 4 angular misalignment

Takes 1/8 parallel misalignment

Takes end-float of 1/4 to 5/16

Dampens vibrations

PT1-15

Fluid Couplings

Clutches and Brakes

Twist in element

Drop in factoryassembled spacer center

Couplings


SPECIFICATION/HOW TO ORDER/NOMENCLATUREPARA-FLEXSPECIFICATIONPARA-FLEX Couplings employ a molded, non-lubricated elastomeric flexing member loaded in shear. The flexible member is compounded natural or neoprene rubber with textile cord reinforcement throughout and has an extra layer of reinforcement adjacent to the split for added durability. The compound of natural rubber element shall be suitable for operation in ambient temperature from -45F to +180F; Neoprene -40F to +210F. The flexible element is attached by clamping between axially separable rings with exposed SAE grade 8 cap screws4. The couplings are designed to be capable of accommodating combined misalignments1 of 4 angular, 1/8 parallel, and 5/16 end float at the full rating of the coupling without restricting the rating or life of the coupling. The flexible element must be replaceable without disturbing the coupled equipment and without the requirement for realignment. The coupling assemblies have optional methods of attachment to the shaft including but not limited to: clearance fit, interference fit or TAPER-LOCK bushings. Clearance fits and interference fits are supplied with an industry standard keyway and two set screws, one over the key and one at 65. Spacer Couplings consist of two hubs and a pre-assembled center assembly. The center assembly is readily removable to facilitate maintenance on pumps or other connected equipment and must be replaceable without disturbing the coupled equipment and without realignment.1 PX40:


4 angular, 1/16 parallel, 3/16 end float. 4 angular, 1/8 parallel, 1/4 end float. 3 PH & PF: 1 angular, 1/16 parallel, 3/16 end float. 4 FBX style couplings utilize class 10.9 metric cap screws.2 PX110:

HOW TO ORDERStandard couplings consist of: (2) Flange Assemblies (1) Flexible Element Spacer Couplings consist of: (2) Hubs (1) Center Assembly

NOMENCLATUREPXPARA-FLEX X = Standard S = Spacer H = High Speed F = Flywheel Size (PX, PS only) ex.: Approx. 4 O.D. FBX = Straight Bore, Extra Capacity FBS = Straight Bore, Short Series TL = TAPER-LOCK BBS = Bored-To-Size, Steel TBS = One Taper Bored, one Bored-To-size, Steel BBPS = BBS, Piloted for Floating Shaft TBPS = TBS, Piloted for Floating Shaft

40

FBX

PT1-16

EASY SELECTIONPARA-FLEXDODGE PRESELECTED PARA-FLEX COUPLINGS FOR ELECTRIC MOTORS @ 1800 RPMPARA-FLEX TAPER-LOCK SERVICE FACTOR SHAFT H.P. FRAME LIGHT MEDIUM HEAVY DIA. 1.0 1.5 2.0 1 143T 0.875 PX40 PX40 PX40 1.5 145T 0.875 PX40 PX40 PX40 2 145T 0.875 PX40 PX40 PX40 3 182T 1.125 PX50 PX50 PX50 5 184T 1.125 PX50 PX50 PX50 7.5 213T 1.375 PX60 PX60 PX60 10 215T 1.375 PX60 PX60 PX60 15 254T 1.625 PX70 PX70 PX70 20 256T 1.625 PX70 PX70 PX70 25 284T 1.875 PX80 PX80 PX80 326T 1.875 PX80 PX80 PX80 30 286TS 1.625 PX70 PX70 PX70 324T 2.125 PX80 PX80 PX80 40 324TS 1.875 PX80 PX80 PX80 326T 2.125 PX80 PX80 PX80 50 326TS 1.875 PX80 PX80 PX80 364T 2.375 PX90 PX90 PX90 60 364TS 1.875 PX80 PX80 PX90 365T 2.375 PX90 PX90 PX110 75 365TS 1.875 PX80 PX90 PX110 404T 2.875 PX120 PX120 PX120 100 404TS 2.125 PX90 PX110 PX110 405T 2.875 PX120 PX120 PX120 405TS 2.125 PX90 PX110 PX120 125 444T 3.375 PX140 PX140 PX140 444TS 2.375 PX100 PX110 PX120 444/5T 3.375 PX140 PX140 PX140 150 444/5TS 2.375 PX100 PX120 PX120 444T 3.375 PX140 * * 200 444TS 2.375 PX110 PX120 PX140 * Consult catalog for other coupling types at these speeds. MOTOR PARA-FLEX STRAIGHT BORE SERVICE FACTOR LIGHT MEDIUM HEAVY 1.0 1.5 2.0 PX40 PX40 PX40 PX40 PX40 PX40 PX40 PX40 PX40 PX40 PX40 PX40 PX40 PX40 PX40 PX40 PX50 PX50 PX40 PX50 PX50 PX50 PX50 PX60 PX50 PX60 PX60 PX50 PX60 PX60 PX60 PX60 PX70 PX60 PX60 PX70 PX60 PX70 PX80 PX60 PX70 PX80 PX60 PX80 PX80 PX60 PX80 PX80 PX70 PX80 PX90 PX70 PX80 PX90 PX80 PX90 PX100 PX80 PX90 PX100 PX80 PX100 PX110 PX80 PX100 PX110 PX90 PX110 PX120 PX90 PX110 PX120 PX90 PX110 PX120 PX90 PX110 PX120 PX100 PX120 PX120 PX100 PX120 PX120 PX110 PX120 PX140 PX110 PX120 PX140 PARA-FLEX SPACER TAPER-LOCK SERVICE FACTOR LIGHT MEDIUM HEAVY 1.0 1.5 2.0 PS40 PS40 PS40 PS40 PS40 PS40 PS40 PS40 PS40 PS50 PS50 PS50 PS50 PS50 PS50 PS60 PS60 PS60 PS60 PS60 PS60 PS60 PS60 PS60 PS60 PS60 PS60 PS70 PS70 PS70 PS70 PS70 PS70 PS60 PS60 PS60 PS70 PS70 PS80 PS70 PS70 PS80 PS70 PS80 PS80 PS70 PS80 PS80 PS80 PS80 PS90 PS70 PS80 PS90 PS80 PS90 PS100 PS80 PS90 PS100 PS120 PS120 PS120 PS80 PS100 PS110 PS120 PS120 PS120 PS90 PS110 PS120 PS140 PS140 PS140 PS90 PS110 PS120 PS140 PS140 PS140 PS100 PS120 PS120 PS140 PS140 PS140 PS110 PS120 PS140 PARA-FLEX SPACER STRAIGHT BORE SERVICE FACTOR LIGHT MEDIUM HEAVY 1.0 1.5 2.0 PS40 PS40 PS40 PS40 PS40 PS40 PS40 PS40 PS40 PS40 PS40 PS40 PS40 PS40 PS40 PS40 PS40 PS50 PS40 PS50 PS50 PS50 PS50 PS60 PS50 PS60 PS60 PS50 PS60 PS60 PS60 PS60 PS70 PS60 PS60 PS70 PS60 PS70 PS80 PS60 PS70 PS80 PS60 PS80 PS80 PS60 PS80 PS80 PS70 PS80 PS90 PS70 PS80 PS90 PS80 PS90 PS100 PS80 PS90 PS100 PS80 PS100 PS110 PS80 PS100 PS110 PS90 PS110 PS120 PS90 PS110 PS120 PS90 PS110 PS120 PS90 PS110 PS120 PS100 PS120 PS120 PS100 PS120 PS120 PS110 PS120 * PS110 PS120 *

PT1-17

Fluid Couplings

FLEXIDYNE

Clutches and Brakes

Couplings



SELECTION/DIMENSIONSStandard, Straight BoreB B

A D C E D

A D C E D D D A E

B TYPE 1

TYPE 2

TYPE 3

FBXCoupling Size Min. Bore Max .Bore HP/100 Torque (In-Lbs) Max. RPM Dwg. Type 1 1 1 1 1 1 2 2 2 A 4.25 5.25 6.50 7.38 8.38 9.25 10.00 11.00 12.38 B 3.50 4.44 5.59 6.13 6.69 7.69 7.13 7.14 7.75 C 2.88 3.14 4.08 4.63 5.39 6.09 5.15 5.56 5.84 D 1.15 1.51 1.84 2.00 2.30 2.70 2.70 2.79 3.00 E .76 .96 1.28 1.50 1.50 1.53 1.71 1.56 1.75 Weight (1) (Lbs.) 4.10 7.70 13.50 19.90 30.00 42.40 50.10 56.00 80.20 Inertia (2) (Lb-Ft2) .05 .10 .26 .54 1.06 1.96 2.71 3.10 5.81

PX40FBX 1/2 1-7/16 .68 429 4500 PX50FBX 5/8 1-7/8 1.43 900 4500 PX60FBX 7/8 2-3/16 2.86 1800 4000 PX70FBX 7/8 2-3/8 3.49 2200 3600 PX80FBX 1-7/16 2-7/8 5.72 3605 3100 PX90FBX 1-7/16 3-3/8 7.15 4502 2800 PX100FBX 1-7/16 3-3/8 8.58 5402 2600 PX110FBX 1-1/2 3-3/4 12.30 7750 2300 PX120FBX 1-1/2 G3-3/4 20.00 12605 2100 Shallow keyway on bores of 3-1/4, 3-3/8. Key provided. Shallow keyway on bores of 3-5/8, 3-3/4. Key provided.

FBSCoupling Size Min. Bore Max. Bore HP/100 Torque (In-Lbs) 900 1800 2200 3605 4502 Max. RPM 4500 4000 3600 3100 2800 Dwg. Type 3 3 3 3 3 A 5.25 6.50 7.38 8.38 9.25 B 2.75 3.36 3.57 3.57 4.03 D .88 1.00 1.00 1.25 1.75 E .53 .71 .95 .95 .33 Weight Inertia (2) (1) (Lb-Ft2) (Lbs.) 4.10 .05 8.20 .16 11.80 .32 16.60 .60 22.60 1.00

PX50FBS 5/8 1-3/8 1.43 PX60FBS 7/8 1-13/16 2.86 PX70FBS 7/8 2-3/16 3.49 PX80FBS 1-7/16 2-11/16 5.72 PX90FBS 1-7/16 2-7/8 7.15 (1) Weight of complete coupling at maximum bore. (2) Inertia of complete coupling at maximum bore.





PT1-18

SELECTION/DIMENSIONSStandard, Straight Bore - Part NumbersFBX FLANGE ASSEMBLIESBore (in.) Reborable Finished Bore Flanges 5/8 3/4 7/8 15/16 1 1-1/16 1-1/8 1-3/16 1-1/4 1-5/16 1-3/8 1-7/16 1-1/2 1-9/16 1-5/8 1-11/16 1-3/4 1-7/8 1-15/16 2 2-1/8 2-3/16 2-1/4 2-3/8 2-1/2 2-5/8 2-3/4 2-7/8 3 3-1/8 3-1/4 3-3/8 3-1/2 3-5/8 3-3/4 PX40FBX 000478 PX50FBX 000480 PX60FBX 000481 Coupling Size/Part Number PX70FBX PX80FBX PX90FBX 000482 000483 000484 PX100FBX 000485 PX110FBX 000486 PX120FBX 000487

000822 000823 000824 000825 000826 000827 000828 000829 000830 000831 000832 000833

000575 000576 000577 000578 000579 000580 000581 000582 000583 000584 000585 000586 000587 000588 000589 000573

000590 003251 000591 003252 000592 003253 000593 003254 000594 000595 000596 000597 000598 000599 000600 000601 000602 000603 000604 000605

000606 003283 000607 003284 000608 003285 000609 003286 000610 003287 000611 003288 000612 003289 000613 000614 003291 000615 000616 003293 000617 000618

000619 000620 003323 000621 003324 000622 000623 003326 000624 000625 003328 000626 000627 000628 000629 000630 000631

FBS FLANGE ASSEMBLIESBore (in.) Reborable PX50FBS 009199 Coupling Size/Part Number PX60FBS PX70FBS PX80FBS 009214 009215 009223 PX90FBS 009230

(1) Standard natural rubber element Part Numbers on Page PT1-22 Stocked ange assemblies Complete coupling consists of (2) FBX or FBS ange assemblies, and (1) element.FEATURES/BENEFITS PAGE PT1-14 EASY SELECTION PAGE PT1-5 MODIFICATION/ACCESSORIES PAGE PT1-67 ENGINEERING/TECHNICAL PAGE PT1-69

PT1-19

Fluid Couplings

FLEXIDYNE

000632 000633 003356 000634 003357 000635 000636 003359 000637 000638 003361 000639 000640 000641 000642 000643 000644 000645 000646 000647 000648

000649 000650 003402 000651 003403 000652 000653 003405 000654 000655 003407 000656 000657 000658 000659 000660 000661 000662 000663 000664 000665

000666 003450 000667 003451 000668 000669 003453 000670 000671 003455 000672 000673 000674 000675 000676 000677 000678 000679 000680 000681 000682 000683 000684

000685 003501 000686 003502 000687 000688 003504 000689 000690 003506 000691 000692 000693 000694 000695 000696 000697 000698 000699 000700 000701 000702 000703

Clutches and Brakes

Couplings



SELECTION/DIMENSIONSStandard, TAPER-LOCKB B

A D D E

A D D E

PX40 STANDARD COUPLING TYPE H TAPER-LOCK

PX40 STANDARD COUPLING TYPE F TAPER-LOCK

K B J

D

D A E TYPE H TYPE F

TYPE HF PX-50-120 PARA-FLEX TAPER-LOCK COUPLINGS

B

K J

A

D E

D TYPE H-H TYPE F-F 1-9/32

TYPE HFPX280 & 320 ONLY

PX-140-320 PARA-FLEX TAPER-LOCK COUPLINGSFEATURES/BENEFITS PAGE PT1-14 EASY SELECTION PAGE PT1-5 MODIFICATION/ACCESSORIES PAGE PT1-67 ENGINEERING/TECHNICAL PAGE PT1-69

PT1-20

SELECTION/DIMENSIONSStandard, TAPER-LOCK

Coupling Size

Max. Bore

HP/100

Torque (In-Lbs)

Max. RPM

A

B

D 0.88 0.88 1.00 1.00 1.25 1.75 1.75 1.75 2.00 3.50 4.00 4.50 5.00 6.00 6.50

E 0.77 0.53 0.72 0.95 0.77 0.33 0.52 0.47 0.44 0.81 1.19 1.31 1.91 2.22 2.06

J (1) 0.63 0.63 0.81 0.81 0.94 1.00 1.00 1.00 1.19 1.31 1.63 1.94 2.31 1.63 1.63

K (2) 0.75 0.75 1.06 1.06 1.38 1.63 1.63 1.63 2.06 2.69 3.38 4.06 4.81 4.38 4.38

PX40TL 1 .68 429 4500 4.25 3.00 PX50TL 1-1/8 1.43 900 4500 5.25 2.75 PX60TL 1-7/16 2.86 1800 4000 6.50 3.34 PX70TL 1-11/16 3.49 2200 3600 7.38 3.56 PX80TL 2-1/8 5.72 3605 3100 8.38 3.75 PX90TL 2-11/16 7.15 4502 2800 9.25 4.03 PX100TL 2-11/16 8.58 5402 2600 10.00 4.22 PX110TL 2-11/16 12.30 7750 2300 11.00 4.53 PX120TL 3-1/4 20.00 12605 2100 12.38 5.03 PX140TL 3-15/16 44.00 27590 1840 14.13 7.81 PX160TL 4-7/16 60.00 37800 1560 16.63 9.19 PX200TL 4-15/16 131.00 82500 1300 20.00 10.31 PX240TL 5 240.00 151200 1080 24.13 11.91 PX280TL 7 480.00 302200 910 28.50 15.97 PX320TL 8 719.00 453000 810 32.50 16.31 Notes: (1) Space required to tighten bushing with shortened hex key. (2) Space required to loosen bushing with shortened hex key. (3) Weight of complete coupling with bushing. (4) Inertia of complete coupling with bushing.

Inertia Weight (Lb-Ft2) (Lbs.) (3) (4) 4.20 0.05 4.70 0.07 9.20 0.21 13.00 0.30 19.60 0.73 28.80 1.30 38.00 2.20 52.10 3.70 74.40 6.60 156.00 18.70 243.00 33.70 417.00 101.00 682.00 231.00 1148.00 544.00 1640.00 1077.00





PT1-21

Fluid Couplings

FLEXIDYNE

Clutches and Brakes

Couplings



SELECTION/DIMENSIONSStandard, TAPER-LOCK Part NumbersTAPER-LOCK FLANGE ASSEMBLIESPart No. Type H Type F PX40 000849 000848 PX50 010601 PX60 010602 PX70 010603 PX80 010604 PX90 010605 PX100 010606 PX110 010607 PX120 010608 PX140 011134 011154 PX160 011137 011157 PX200 011140 011160 PX240 011144 011164 PX280 011455 011456 PX320 011472 011471 PX50-PX120 have a reversible ange for type H or F mount Complete coupling consists of (2) TAPER-LOCK Flange Assemblies, and (1) element. Coupling Size Flange Assembly TAPER-LOCK Bushing Size 1008 1108 1310 1610 2012 2517 2517 2517 3020 3535 4040 4545 5050 7060 8065

STANDARD NATURAL RUBBER ELEMENTS Flexible Element Part No. PX40 011529 PX50 011105 PX60 011106 PX70 011107 PX80 011108 PX90 011109 PX100 011110 PX110 011111 PX120 011112 PX140 011114 PX160 011117 PX200 011120 PX240 011124 PX280 011457 PX320 011463 See page PT1-67 for optional elements Coupling Size





PT1-22

SELECTION/DIMENSIONSStandard, TAPER-LOCK Part NumbersMETRIC PARA-FLEX TAPER-LOCK FLANGE ASSEMBLIESFlange Assembly Taper-Lock Part No. Bushing Size Type H Type F PXM40 013095 013096 1008 PXM50 013040 013041 1210 PXM60 013043 013042 1610 PXM70 013044 1610 PXM80 013045 2012 PXM90 013046 2517 * PXM100 013047 2517 * PXM110 013048 2517 * PXM120 013049 3020 PXM70 - PXM120 have a reversible ange for type H or F mount. * Hard metric bushing required Note: For TAPER-LOCK designs, TAPER-LOCK bushings must be ordered separately. Coupling Size





PT1-23

Fluid Couplings

FLEXIDYNE

Clutches and Brakes

Couplings



SELECTION/DIMENSIONSSpacer, Straight BoreK K

A D D D C D C

E

TYPE 1

TYPE 2

SPACER COUPLING CENTER ASSEMBLY

SPACER SHAFT HUBSCoupling Size PS40FBX PS50FBX PS60FBX PS60FBS PS70FBX PS70FBS PS80FBX PS80FBS PS90FBX PS90FBS PS100FBX PS100FBS PS110FBX PS110FBS PS120FBX PS120FBS Min. Bore 1/2 5/8 2 7/8 2 7/8 2-1/8 1-7/16 2-1/8 1-7/16 2-5/8 1-7/16 2-5/8 1-7/16 2-5/8 1-1/2 Max. Bore 1-7/16 1-7/8 2-3/16 1-15/16 2-3/8 1-7/8 3-3/8 2-1/8 3-3/8 2-1/8 3-3/4 2-1/2 3-3/4 2-1/2 3-3/4 2-1/2 HP/100 0.68 1.43 2.86 2.86 3.49 3.49 5.72 5.72 7.15 7.15 8.58 8.58 12.3 12.3 20.0 20.0 Torque (In-Lbs) 429 900 1800 1800 2200 2200 3605 3605 4502 4502 5402 5402 7750 7750 12605 12605 Max. RPM 4500 4500 4000 4000 3600 3600 3100 3100 2800 2800 2600 2600 2300 2300 2100 2100 Dwg. Type 1 1 1 1 1 2 1 2 1 2 1 2 1 2 2 2 C 2.88 3.81 4.45 4.45 5.02 5.02 6.02 6.02 6.02 6.02 6.77 6.77 6.77 6.77 8.27 8.27 D 1.13 1.41 1.28 1.22 1.78 1.22 2.53 1.50 2.53 1.50 2.53 1.88 2.53 1.88 2.81 1.88 K (1) 1.75 2.25 2.13 2.50 2.63 1.25 3.38 1.50 3.38 1.50 3.50 1.50 3.50 1.50 1.88 1.88 Weight (Lbs.) (2) 1.30 3.20 4.90 4.00 7.10 2.90 12.90 5.30 12.90 5.30 16.50 7.30 16.50 7.30 14.40 14.60 Inertia (Lb. Ft.2) 0.01 0.05 0.11 0.08 0.18 0.06 0.53 0.16 0.53 0.16 0.85 0.26 0.85 0.26 0.50 0.51

SPACER CENTER ASSEMBLIESCoupling Size PS40 PS50 PS60 PS70 PS80 PS90 PS100 PS110 PS120 A 4.25 5.25 6.50 7.38 8.38 9.25 10.00 11.00 12.38 E Min. 2.75 2.88 3.38 3.50 3.50 3.50 3.50 3.50 4.50 Max. 5.75 7.33 7.33 7.50 10.00 10.00 10.00 10.00 10.00 Weight (Lbs.) (3) 4.00 6.90 9.50 12.20 16.90 21.10 23.60 41.00 56.40 Weight Adder (4) 0.50 1.28 1.70 2.10 2.90 2.90 3.87 3.87 5.86 Inertia (Lb.Ft.2) (5) 0.04 0.10 0.28 0.50 0.89 1.40 2.10 3.30 7.30 Inertia Adder (6) 0.01 0.02 0.03 0.07 0.22 0.22 0.28 0.28 0.76

(1) Screw clearance required to remove center assembly (2) Hub weight at maximum bore (3) Center assembly weight at minimum lengthFEATURES/BENEFITS PAGE PT1-14 EASY SELECTION PAGE PT1-5

(4) Weight adder per inch length (5) Center assembly inertia at minimum length (6) Inertia adder per inch lengthMODIFICATION/ACCESSORIES PAGE PT1-67 ENGINEERING/TECHNICAL PAGE PT1-69

PT1-24

SELECTION/DIMENSIONSSpacer, Straight Bore Shaft Hub - Part Numbers (1)PS40 FBX Reborable 000479 5/8 000836 3/4 000837 7/8 000838 15/16 000839 1 000840 1-1/16 000841 1-1/8 000842 1-3/16 000843 1-1/4 000844 1-5/16 000845 1-3/8 000846 1-7/16 000847 1-1/2 1-9/16 1-5/8 1-11/16 1-3/4 1-7/8 1-15/16 2 2-1/8 2-3/16 2-1/4 2-3/8 2-1/2 2-5/8 2-3/4 2-7/8 3 3-1/8 3-1/4 3-3/8 3-1/2 3-5/8 3-3/4 Bore (in.) PS50 FBX 000490 000704 000705 000706 000707 000708 000709 000710 000711 000712 000713 000714 000715 000716 Coupling Size/Part Number PS70 PS80/90 PS100/110 PS120 FBS FBX FBS FBX FBS FBX FBS FBX FBS FBX 000492 000491 000494 000493 000496 000495 000498 000497 000500 000499 PS60

000719 000720 000721 000722

000739 000740 000741 000742 000743 000744 000745 000746 000747 000732 000733 000734 000735 000736 000737 000738 000759 000760 000761 000762 000763 000776 000777 000778 000779 000780 000796 000797 000798 000799 000800 000801Clutches and Brakes Fluid CouplingsENGINEERING/TECHNICAL PAGE PT1-69

000723 000724 000725 000726 000717 000727 000728 000718 000729 000574 000730 000731

000764 000781 000765 000748 000782

000749 000783 000802 000750 000784 000803 000751 000785 000804 000752 000766 000786 000753 000767 000787 000754 000768 000788 000755 000769 000789 000756 000770 000790 000757 000771 000791 000758 000772 000792 000773 000793 000774 000794 000775 000795

Stocked shaft hubs (1) See page PT1-27 for spacer center assembly part numbers. Complete coupling consists of: (2) Shaft Hubs, TAPER-LOCK or Straight Bore (1) Spacer Center Assembly NOTE: Standard Bore Tolerances: Straight bore couplings from PX40 - PX120 are furnished with clearance t. PX140 - PX320 are furnished with interference t.




PT1-25

FLEXIDYNE

Couplings



SELECTION/DIMENSIONSSpacer, TAPER-LOCKK K

A C D D C

E

TYPE 2

TYPE 1 SPACER COUPLING CENTER ASSEMBLY

TAPER-LOCK SPACER SHAFT HUBSCoupling Size PS40TL PS50TL PS60TL PS70TL PS80TL PS90TL PS100TL PS110TL PS120TL PS140TL PS160TL PS200TL Coupling Size PS40 PS50 PS60 PS70 PS80 PS90 PS100 PS110 PS120 PS140 PS160 PS200 Max. Bore 1 1-1/4 1-11/16 2-1/8 2-11/16 2-11/16 2-11/16 2-11/16 3-1/4 3-15/16 4-7/16 4-15/16 HP/100 .68 1.43 2.86 3.49 5.72 7.15 8.58 12.30 20.00 44.00 60.00 131.00 Torque (In-Lbs) 429 900 1800 2200 3605 4502 5402 7750 12605 27590 37800 82500 E Min. 2.75 2.88 3.38 3.50 3.50 3.50 3.50 3.50 4.50 6.44 8.06 9.94 Max. 5.75 7.33 7.33 7.50 10.00 10.00 10.00 10.00 10.00 13.00 11.44 12.88 Max. RPM 4500 4500 4000 3600 3100 2800 2600 2300 2100 1840 1560 1300 Dwg. Type 1 2 2 2 2 2 2 2 2 1 1 1 C 2.88 3.81 4.44 5.00 6.00 6.00 6.75 6.75 8.25 7.69 8.63 10.00 Weight (Lbs.) (3) 4.00 6.90 9.50 12.20 16.90 21.10 23.60 41.00 56.40 115.00 216.00 290.00 D 0.88 1.00 1.00 1.25 1.75 1.75 1.75 1.75 2.00 3.50 4.00 4.50 Weight Adder (4) .50 1.28 1.70 2.10 2.90 2.90 3.87 3.87 5.86 4.49 5.58 7.65 K(1) 1.75 1.00 1.00 1.00 1.25 1.25 1.25 1.25 1.50 4.50 5.00 5.50 Weight (Lbs) (2) 1.10 1.80 2.40 4.00 7.70 7.70 9.00 9.00 16.60 37.00 55.00 87.40 Inertia (Lb.Ft.2) 0.01 0.02 0.03 0.07 0.22 0.22 0.28 0.28 0.76 2.20 3.90 8.00 Inertia Adder (6) 0.01 0.02 0.03 0.07 0.22 0.22 0.28 0.28 0.76 0.80 0.90 1.60

SPACER CENTER ASSEMBLIESA 4.25 5.25 6.50 7.38 8.38 9.25 10.00 11.00 12.38 14.13 16.63 20.00 Inertia (Lb. Ft.2) (5) 0.04 0.10 0.28 0.50 1.89 1.40 2.10 3.30 7.30 18.70 33.70 101.00

(1) Screw clearance required to remove center assembly (2) Hub weight includes bushing at max. bore (3) Center assembly weight at minimum lengthFEATURES/BENEFITS PAGE PT1-14 EASY SELECTION PAGE PT1-5

(4) Weight adder per inch length (5) Center assembly inertia at minimum length (6) Inertia added per inch lengthMODIFICATION/ACCESSORIES PAGE PT1-67 ENGINEERING/TECHNICAL PAGE PT1-69

PT1-26

SELECTION/DIMENSIONSSpacer, TAPER-LOCK Shaft - Hubs Part NumbersCoupling Size PS40 PS50 PS60 PS70 PS80 PS90 PS100 PS110 PS120 PS140 PS160 PS200 Shaft Hub Part No. 000850 011620 011621 011622 011623 011623 011624 011624 011625 011626 011627 011628 TAPER-LOCK Bushing Size 1008 1210 1610 2010 2517 2517 2517 2517 3020 3535 4040 4545

For complete listing of part numbers for all BSE lengths, see page PT1-28 and PT1-29 Complete coupling consists of: (2) shaft hubs, TAPER-LOCK straight bore, and (1) Spacer center assy NOTE: For TAPER-LOCK designs, TAPER-LOCK bushings must be ordered separatelyFLEXIDYNEFEATURES/BENEFITS PAGE PT1-14 EASY SELECTION PAGE PT1-5 MODIFICATION/ACCESSORIES PAGE PT1-67 ENGINEERING/TECHNICAL PAGE PT1-69

PT1-27

Fluid Couplings

Clutches and Brakes

Couplings



SELECTION/DIMENSIONSPARA-FLEXSPACER CENTER ASSEMBLY PART NUMBERSB.S.E. PS40 PS50 PS60 PS70 PS80 2-7/8 011121 3 011125 3-1/8 011132 3-1/4 011145 3-3/8 011152 010723 3-1/2 000854 011565 011567 N 011569 N 011571 3-5/8 011720 011726 011740 011775 3-11/16 3-3/4 011721 011727 011741 011776 3-7/8 011722 011728 011742 011777 4 011723 011729 011743 011778 4-1/8 011724 011730 011744 011779 4-1/4 011725 011731 011745 011780 4-3/8 011582 011732 011746 011781 4-1/2 011583 011584 4-5/8 011733 011747 011782 4-3/4 011734 011748 011783 4-7/8 011749 011784 5 000857 012767 012765 011750 011785 5-1/8 011751 011786 5-1/4 011752 011787 5-5/16 5-3/8 011753 011788 5-1/2 011754 011789 5-5/8 011755 011790 5-3/4 000858 000859 000861 011756 011791 5-7/8 011757 011792 6 011758 011793 6-1/16 6-1/8 011602 011794 6-1/4 011759 011795 6-5/16 6-3/8 011760 011796 6-7/16 6-1/2 011761 011797 6-5/8 011762 011798 6-3/4 011763 011799 6-7/8 011764 011604 7 012766 011765 011800 7-1/8 011766 011801 7-1/4 011767 011802 7-1/3 000860 000862 012289 7-3/8 011768 011803 7-1/2 011603 011804 7-5/8 011805 7-3/4 011806 7-7/8 011807 Stock Center AssembliesFEATURES/BENEFITS PAGE PT1-14 EASY SELECTION PAGE PT1-5

PS90

PS100

PS110

PS120

PS140

PS160

PS200

N 011564 N 011579 N 011580 011890 011891 011892 011893 011894 011895 011896 011897 011581 011898 011899 011935 011900 011936 011705 011937 011901 011938 011902 011939

011589

011555 011810 011850 011811 011851 011812 011852 011586 011587 011813 011853 011814 011854 011815 011855 011816 011700 011817 011856 011818 011857 011847 011819 011858 011903 011940 011820 011859 011904 011941 011821 011860 011905 011942 011822 011861 011906 011943 011823 011862 011907 011944 011824 011701 011706 011710 011825 011826 011827 011863 011864 011865 011908 011909 011910 011945 011946 011947

010539 011828 011866 011911 011948 010547 011829 011867 011912 011949 010548 011830 011868 011913 011950 010549 011606 011869 011914 011951 010550 011831 011702 011707 011711 010551 011832 011870 011915 011952 010552 011833 011871 011916 011953 010553 012291 012290 011834 011872 011917 011954 010554 011835 011873 011918 011955 010555 011836 011874 011919 011956 010556 011837 011875 011920 011957 010975 011838 011876 011921 011958 010976



PT1-28

SELECTION/DIMENSIONSPARA-FLEXSPACER CENTER ASSEMBLY PART NUMBERSB.S.E. PS40 PS50 Semi Fin 000851 010997 8 8-1/16 8-1/8 8-3/16 8-1/4 8-3/8 8-1/2 8-5/8 8-3/4 8-7/8 9 9-1/8 9-3/16 9-1/4 9-3/8 9-1/2 9-5/8 9-3/4 9-7/8 9-15/16 10 10-1/8 10-1/4 10-5/16 10-3/8 10-1/2 10-5/8 10-3/4 10-7/8 11 11-1/8 11-1/4 11-3/8 11-7/16 11-1/2 11-5/8 11-3/4 11-7/8 12 12-1/8 12-1/4 12-3/8 12-1/2 12-5/8 12-3/4 12-7/8 13 Stock Center AssembliesFEATURES/BENEFITS PAGE PT1-14

PS60 010998

PS70 011012

PS80 011000 011605 009420 009419 009421 009422 009423 009424 009425 009426 009427 009428 009429 009430 009431 009432 009433 009434

PS90 011001 011839 011840 011841 011842 011607

PS100 011002 011703 011877 011878 011879 011880

PS110 011005 011708 011922 011923 011924 011925 011926 011927 011928 011709 011929 011930

PS120 011006 011712 011959 011960 011961 011962 011963 011964 011965 011713 011966 011967 012023 012024 012025 012026 012027 012028

PS140 011113 010977 010978 010979 010980 010981 010982 010983 010984 010985 010986

PS160 011115 010595 010567 010568 010569 010570 010571 010572 010573 010574 010575

PS200 011119

009435 000863




PT1-29

Fluid Couplings

010699 000864 000865 012029 010993 010582 010675 010994 010583 010676 010995 010584 010677 010996 009436 010585 010678 009437 010586 010679 009438 010587 010680 009439 010588 010681 009440 010589 010682 009441 010590 010683 009442 010591 010684 009443 010592 010685 009444 010593 010686 010594 009445 010687 009446 010688 009447 010689 009448 010690 009449 010691 009450 010692 009451 010693 010694 009452 009453 010695 009454 010696 009455 010697 009456 010698 009457

FLEXIDYNE

Clutches and Brakes

010987 010576 010988 010577 010989 010578 010990 010579 010991 010580 010992 010581

Couplings



SELECTION/DIMENSIONSBored to Size, Type BBSB D D

A C E

PX60 THRU PX320 TYPE BBS COUPLINGSCoupling Size Min. Bore Max. Bore HP/100 Torque (In-Lbs) Max. RPM 4000 3600 3100 2800 2600 2300 2100 1840 1560 1300 1080 910 810 A 6.50 7.38 8.38 9.25 10.00 11.00 12.38 14.13 16.63 20.00 24.13 28.50 32.50 B 4.28 5.00 5.50 6.03 6.97 7.56 8.25 9.81 12.94 15.56 14.16 18.47 20.75 C 2.38 2.94 3.69 4.13 4.94 5.44 5.81 7.00 8.50 9.38 10.00 12.00 14.00 D 1.50 1.75 2.00 2.25 2.63 3.00 3.25 3.88 5.13 6.13 5.13 7.13 8.13 E 1.28 1.50 1.50 1.53 1.72 1.56 1.75 2.44 3.06 3.75 4.34 4.66 4.94 Weight (1) Inertia (2) (Lbs.) (Lb-Ft2) 8.8 .21 12.8 .32 18.4 .79 25.6 1.4 36.4 2.5 47.3 4.2 68.4 7.0 127.2 16.4 210.8 39.6 333.5 76.9 481.0 188.1 802.0 440.8 1074.0 709.6

PX60BBS none 1-1/2 2.86 1,800 PX70BBS none 2-1/8 3.49 2,200 PX80BBS none 2-9/16 5.72 3,605 PX90BBS none 2-3/4 7.15 4,502 PX100BBS none 3-1/4 8.58 5,402 PX110BBS none 3-15/16 12.30 7,750 PX120BBS none 4 20.00 12,605 PX140BBS 2-1/4 4-1/2 44.00 27,590 PX160BBS 2-1/2 6 60.00 37,800 PX200BBS 2-7/8 6-3/4 131.00 82,500 PX240BBS 4 7-1/2 240.00 151,200 PX280BBS 4-7/16 9 480.00 302,200 PX320BBS 5-1/2 11 719.00 453,000 (1) Weight of complete coupling at maximum bore (2) Inertia of complete coupling at maximum bore





PT1-30

SELECTION/DIMENSIONSBored to Size, Type BBS

PX60BBS - PX320BBS PART NUMBERSCoupling Size PX60BBS PX70BBS PX80BBS PX90BBS PX100BBS PX110BBS PX120BBS PX140BBS PX160BBS PX200BBS PX240BBS PX280BBS PX320BBS BS Flange Assemblies Rough Bore (2 Reqd) 010300 010301 010302 010303 010304 010305 010306 010530 010531 010532 010533 010528 010529 Standard Element (1 Reqd) 011106 011107 011108 011109 011110 011111 011112 011114 011117 011120 011124 011457 011463 When bored to size, the PX60 through PX120 BBS sizes are furnished with clearance t, standard keyway and two-set screws. PX140 and larger sizes are furnished as interference t with standard keyway and no setscrew. Complete coupling consists of: (2) BS Flange Assemblies and (1) Standard Element.Clutches and Brakes Fluid CouplingsFEATURES/BENEFITS PAGE PT1-14 EASY SELECTION PAGE PT1-5 MODIFICATION/ACCESSORIES PAGE PT1-67 ENGINEERING/TECHNICAL PAGE PT1-69

PT1-31

FLEXIDYNE

Couplings



SELECTION/DIMENSIONSMill Motor, Type TBS*

F L

BSize PX60TBS PX70TBS PX80TBS PX90TBS PX100TBS PX110TBS PX120TBS For Mill Motor Size 602,802* 603 802B,802C 603,803 604804 804 804 606,806 608 608,806 608,808 808 PX140TBS 610-810 612 810 PX160TBS 612-812 614 812 PX200TBS 614-814 616-816 618-818 PX240TBS PX280TBS 818 620 622 624 4 5-1/4 7-1/2 9 240.00 480.00 151,200 302,200 1080 910 2-7/8 6-3/4 131.00 82,500 1300 2-1/2 6 60.00 37,800 1560 2-1/4 4-1/2 44.00 27,590 1840 Min. Bore none none none none none none none Max. Bore 1-1/2 2-1/8 2-9/16 2-3/4 3-1/4 3-15/16 4 HP/100 2.86 3.49 5.72 7.15 8.58 12.30 20.00 Torque (In-Lbs) 1,800 2,200 3,605 4,502 5,402 7,750 12,605 Max. RPM 4000 3600 3100 2800 2600 2300 2100 B 5.78 6.75 6.25 7.00 7.00 7.28 7.84 8.56 9.06 9.00 9.50 10.63 10.63 11.06 12.50 12.94 12.94 14.63 14.63 15.13 15.56 15.22 15.91 18.78 20.78 F 3.00 3.50 3.00 3.50 3.50 3.50 3.50 4.00 4.50 4.00 4.50 4.69 4.69 5.13 4.69 5.13 5.13 5.19 5.19 5.69 6.13 6.19 6.88 7.44 9.44 L 0.34 0.50 0.56 0.50 0.50 0.53 0.72 0.59 0.16 0.63 0.50 1.19 1.06 0.94 1.69 1.56 1.44 2.19 2.06 1.94 2.38 2.97 2.53 2.22 2.22 519 836 188.1 440.8 344.5 76.9 227.8 39.6 136.2 16.4 Weight(1) (Lbs.) 10.1 16.1 23.2 29.9 44.4 62.3 81.4 Inertia(2) (Lb-Ft2) 0.21 0.32 0.79 1.4 2.5 4.2 7.0

Refer to page PT1-30 for additional envelope information

* 1-1/4 per foot taper on diameter





PT1-32

SELECTION/DIMENSIONSMill Motor, Type TBS*

PX60 - PX280 TBS PART NUMBERSCoupling Size PX60TBS PX70TBS PX80TBS PX90TBS PX100TBS PX110TBS PX120TBS For Mill Motor Size 602,802* 603 802B,802C 603,803 604,804 804 804 606,806 608 606,806 608,808 608,808 610,810 612,812 610,810 612,812 614 612,812 614,814 616,816 618,818 818 620 622 624 TS Flange Assy (1) Reqd + 010471 010472 010473 010474 010475 010476 010477 010478 010479 010480 008980 008981 008982 008983 008984 008985 008986 008987 008988 008989 008990 008991 008992 008993 Std. Element (1) Reqd 011106 011107 011108 011109 011110 011111 011112 See Page PT1-30 BS Flange Assy (1) Reqd Coupling Size PX60TBS PX70TBS PX80TBS PX90TBS PX100TBS PX110TBS PX120TBS PX140TBS PX160TBS PX200TBS PX240TBS PX280TBS TS Flange Assy Rough Bore 010510 010511 010512 010513 010514 010515 010516 010524 010531 010532 010525 010526

PX140TBS

011114

PX160TBS

011117 Complete coupling consists of: (1) TS Flange Assembly, (1) BS Flange Assembly, and (1) Standard Element. * Key furnished for shallow keyways. 011124 011457 + Part numbers are nished bore anges to t mill motor sizes listed.

PX200TBS

011120

PX240TBS PX280TBS





PT1-33

Fluid Couplings

FLEXIDYNE

Clutches and Brakes

Couplings



SELECTION/DIMENSIONSFloating Shaft, Type BBPSB E BPS FLG ASSY BCS FLG ASSYT U BPS FLG FLG BPS ASSY ASSY BS FLGBS ASSY AS B B

A

A

L

L

K

K

C

C

L

KFLOATING SHAFT TYPE BBPS FLOATING SHAFT DETAIL

D

ED

D E

D

D

D

FLOATING SHAFT TYPE BBPS

PX60 -120 BBPS

PX140-320 BBPS BBPS PX140-320

Size PX60BBPS PX70BBPS PX80BBPS PX90BBPS PX100BBPS PX110BBPS PX120BBPS PX140BBPS PX160BBPS PX200BBPS PX240BBPS PX280BBPS PX320BBPS

Min. Max. Torque Max HP/100 A B C D Bore Bore (In-Lbs) RPM none 1-1/2 2.86 1,800 4000 6.50 4.28 2.38 1.50 none 2-1/8 3.49 2,200 3600 7.38 5.00 2.94 1.75 none 2-9/16 5.72 3,605 3100 8.38 5.50 3.69 2.00 none 2-3/4 7.15 4,502 2800 9.25 6.03 4.13 2.25 none 3-1/4 5.85 5,402 2600 10.00 6.97 4.94 2.63 none 3-15/16 12.30 7,750 2300 11.00 7.56 5.44 3.00 none 4 20 12,605 2100 12.38 8.25 5.81 3.25 2-1/4 4-1/2 44 27,590 1840 14.13 9.19 7.00 3.88 2-1/2 6 60 37,800 1560 16.63 12.94 8.50 5.13 2-7/8 6-3/4 131 82,500 1300 20.00 15.56 9.38 6.13 4 7-1/2 240 151,200 1080 24.13 14.16 10.00 5.13 4-7/16 9 480 302,200 910 28.50 18.47 12.00 7.13 5-1/2 11 719 453,000 810 32.50 20.75 14.00 8.13

E

K

L

T

U 1.28 1.58 1.58 1.70 1.72 1.69 1.98 2.00 2.94 2.84 3.12 3.28 3.44

1.78 2.45 0.58 .624/.6225 2.06 3.05 0.48 .999/.9975 2.00 3.30 0.45 .999/.9975 2.09 3.67 0.39 1.249/1.2475 2.16 4.13 0.44 1.249/1.2475 2.06 4.44 0.38 1.249/1.2475 2.44 4.89 0.45 1.499/1.497 2.44 5.69 0.44 1.499/1.497 3.06 7.25 0.75 1.499/1.497 3.69 8.78 0.84 1.999/1.997 4.28 8.06 1.16 1.999/1.997 4.59 10.22 1.31 1.999/1.997 4.88 11.38 1.44 1.999/1.997

Weight Inertia (Lbs) (Lb-Ft2) 9.8 0.21 14.6 0.32 26.9 0.79 29.0 1.4 40.1 2.5 51.0 4.2 75.7 7.0 140.2 16.4 230.8 39.6 364.5 76.9 529.0 188.1 877.0 440.8 1181.0 709.6

PX60BBPS - PX320BBPS PART NUMBERSCoupling Size PX60BBPS PX70BBPS PX80BBPS PX90BBPS PX100BBPS PX110BBPS PX120BBPS Coupling Size PX140BBPS PX160BBPS PX200BBPS PX240BBPS PX280BBPS PX320BBPS BCS Flange Assy (1) Reqd 010658 010660 010189 010191 010193 010599 010195 BS Flange Assy (1) Reqd 010530 010531 010532 010533 010528 010529 BPS Flange Assy (1) Reqd 010657 010659 010190 010192 010194 010598 010196 BPS Flange Assy (1) Reqd 011714 011715 011716 011717 011718 011719 Std Element (1) Reqd 011106 011107 011108 011109 011110 011111 011112 Std Element (1) Reqd 011114 011117 011120 011124 011457 011463

Complete coupling consists of: (1) BCS or BS Flange Assembly (depending on size of coupling), (1) BPS Flange Assembly, and (1) Standard Element. BCS Flange Assembly consists of:1. External Clamp Ring 2. Internal Clamp Ring 3. BCS Flange

BPS Flange Assembly consists of:1. External Clamp Ring 2. Piloted Internal Clamp Ring a. Includes oating shaft bearing assembly 3. BS Flange





PT1-34

FEATURES /BENEFITSPARA-FLEX High Speed and Flywheel Couplings

HIGH SPEED TYPE Compensates for misalignment Cushions thrust loads Absorbs vibration and shock Prolongs bearing life Available in TAPER-LOCK and bored to size congurationsCouplings Fluid Couplings FLEXIDYNE Clutches and Brakes

FLYWHEEL TYPE Specically designed to connect the exible element to standard SAE ywheel bolt patterns Available in TAPER-LOCK and bored to size congurations

PT1-35



SELECTION/DIMENSIONSHigh Speed, TAPER-LOCKB G K J F1 D1 J E D TAPER-LOCK FLANGE ASSEMBLY M L

A F

E1

FLEXIBLE ELEMENT TYPE "H" DISC DISC ASSEMBLY TYPE "F" DISC

PH87 THRU PH131

B K J J K

G FLEXIBLE ELEMENT

F

D

E

D

C

A

F1

E1

TYPE SH FLANGE DISC ASSEMBLY

TYPE SF FLANGE

PH172 thru PH252

STEEL FLANGE ASSEMBLY

B K J K J

G FLEXIBLE ELEMENT

F

D E

D

C

A

F1

E1

TYPE H FLANGE DISC ASSEMBLY

TYPE F FLANGE

PH172 & PH192 IRON FLANGE ASSEMBLY





PT1-36

SELECTION/DIMENSIONSHigh Speed, TAPER-LOCKCoupling Size PH87 PH96 PH116 PH131 PH172 PH192 PH213 PH252 Coupling Size PH87 PH96 PH116 PH131 PH172 PH192 PH213 PH252 Bushing Size + * 2517 2517 3535 4040 4545 5050 A 9.44 10.31 12.31 13.81 18.31 20.31 22.50 26.50 Min. Bore 1/2 1/2 1/2 1/2 1-3/16 1-7/16 1-15/16 2-7/16 Max. Bore + * 2-11/16 2-11/16 3-15/16 4-7/16 4-15/16 5-5/16 B Iron Flg 3.53 4.30 4.44 5.45 8.06 9.31 ..... ..... Steel Flg ..... ..... ..... ..... 8.97 10.25 11.31 14.31 Iron Flg ..... ..... ..... ..... 7.50 8.63 ..... ..... HP/100 3.0 4.5 7.1 9.5 23.0 47.0 90.0 135.0 Torque (In-Lbs) 1890 2835 4470 5985 14490 29610 56700 85050 C Steel Flg ..... ..... ..... ..... 7.00 8.50 8.75 9.50 Max. RPM Gray Iron Steel Flange Flange 6000 ..... 5230 ..... 4050 ..... 3750 ..... 1860 2800 1620 2430 ..... 2130 ..... 1945 D 1.00 1.25 1.75 1.75 3.50 4.00 4.50 5.00 Weight (Lbs) Iron Flg 19.5 27.2 40.8 59.7 138.2 219.6 ..... ..... D1 1.75 1.75 1.75 1.75 ..... ..... ..... ..... Steel Flg ..... ..... ..... ..... 128.5 219.6 291.2 389.9 Inertia (Lb-Ft2) Iron Flg 1.32 2.44 4.92 8.87 31.74 51.09 102.3 144.1 E Iron Flg 0.81 1.33 1.14 1.95 1.06 1.31 ..... ..... Steel Flg ..... ..... ..... ..... 1.88 2.25 2.31 4.31 Steel Flg ..... ..... ..... ..... 29.98 50.37 90.22 133.7

PH87 - PH252 PART NUMBERSCoupling Size Std Flange Flange Size TAPER-LOCK Flange (1) Reqd Iron Flange Steel Flange Type H Type F Type SH Type SF .......... .......... .......... .......... Disc HS Bushing Assy Element Size (1) Reqd (1) Reqd 011307 011227 + 011308 011228 * .......... .......... 011310 011230 2517 011311 011231 2517 010290 010294 011314 011234 3535 010291 010295 011316 011236 4040 010292 010296 011319 011239 4545 010293 010297 011322 011242 5050 Complete coupling consists of: (1) TAPER-LOCK Flange Assembly, (1) TAPER-LOCK Disc Assembly, & (1) High speed Element. TAPERLOCK bushings must be ordered separately.MODIFICATION/ACCESSORIES PAGE PT1-67 ENGINEERING/TECHNICAL PAGE PT1-69

PH87 010603 PX70 PH96 010604 PX80 PH116 010606 PX100 .......... .......... PH131 010607 PX110 PH172 .......... PX140 011134 011154 PH192 PX160 011137 011157 PH213 .......... PX190 .......... .......... PH252 PX220 + Flange assembly uses a 1610 bushing with 1-11/16 max. bore Disc assembly uses a 2517 bushing with 2-11/16 max. bore * Flange assembly uses a 2012 bushing with 2-1/8 max. bore Disc assembly uses a 2517 bushing with 2-11/16 max. boreFEATURES/BENEFITS PAGE PT1-2 EASY SELECTION PAGE PT1-17

PT1-37

Fluid Couplings

FLEXIDYNE

E1 Coupling G F1 J K L M F Size Iron Flg Steel Flg Iron Flg Steel Flg PH87 0.50 ..... 4.12 4.19 3.28 ..... 1.00 1.63 0.81 1.06 PH96 0.45 ..... 4.12 4.19 3.42 ..... 1.00 1.63 0.94 1.38 PH116 0.33 ..... 4.12 4.19 3.63 ..... 1.00 1.63 1.00 1.63 PH131 0.77 ..... 4.12 4.19 4.27 ..... 1.00 1.63 1.00 1.63 PH172 0.63 1.44 6.25 7.12 7.62 8.53 1.31 2.69 ..... ..... PH192 0.38 1.31 7.75 8.62 8.38 9.31 1.63 3.38 ..... ..... PH213 ..... 1.44 8.75 9.75 ..... 10.44 1.94 4.06 ..... ..... PH252 ..... 2.94 9.50 10.88 ..... 12.94 2.31 4.81 ..... ..... Space required to tighten bushing with shortened hex key or to loosen screws to permit removal of the hub by a puller Space required to loosen bushing with the shortened hex key using screws as hack screws - no puller required.

Clutches and Brakes

Couplings



SELECTION/DIMENSIONSHigh Speed, Bored to SizeB GB G

D E

D1 C A E1

D

E

D1

C

A

E1

TYPE "F" DISC TYPE "H" DISC SIZE PH87 - 131 TYPE "F" DISC SIZE PH172 - 252

TYPE "H" DISC

Coupling Size

BS Flange Assembly Min Bore none none none none 2-1/4 2-1/2 2-1/2 2-7/8

PH87B PH96B PH116B PH131B PH172B PH192B PH213B PH252B

TAPER-LOCK Disc Assembly Max Min Max Bore Bore Bore 2-1/8 1/2 2-11/16 2-9/16 1/2 2-11/16 3-1/4 1/2 2-11/16 3-15/16 1/2 2-11/16 4-1/2 1-3/16 3-15/16 6 1-7/16 4-7/16 6-1/4 1-15/16 4-15/16 6-7/8 2-7/16 5-5/16 BS Flange Assy (1) Reqd

A

B

C

D

D1

E

E1

G

Weight Inertia (Lbs) (Lb-Ft2) 20.1 28.0 42.8 60.1 135.2 220.6 289.2 379.9 1.33 2.47 5.31 9.08 30.98 54.27 91.62 135.9

9.44 10.31 12.31 13.81 18.31 20.31 22.50 26.50

4.59 5.44 6.13 7.25 9.06 11.19 11.31 14.31

2.94 3.69 4.94 5.44 7.00 8.50 8.75 9.50

1.75 1.75 1.75 1.75 3.50 4.00 4.50 5.00

1.75 2.00 2.63 3.00 3.88 5.13 4.69 5.19

1.09 1.69 1.75 2.50 1.88 2.25 2.31 4.31

0.81 0.81 0.97 1.31 1.44 1.31 1.44 2.94

4.31 4.56 5.31 6.06 8.63 10.25 10.44 12.94

TAPER-LOCK TAPER-LOCK HS Element Disc Assy Bushing (1) Reqd (1) Reqd Size PH87B 010301 011307 2517 011227 PH96B 010302 011308 2517 011228 PH116B 010304 011310 2517 011230 PH131B 010305 011311 2517 011231 PH172B 010530 011314 3535 011234 PH192B 010531 011316 4040 011236 PH213B 010508 011319 4545 011239 PH252B 010509 011322 5050 011242 Complete coupling consists of: (1) BS Flange Assembly, (1) TAPER-LOCK Disc Assembly, (1) High Speed Element, and (1). TAPER-LOCK Bushing. TAPER-LOCK bushings must be ordered separately. Coupling Size





PT1-38

SELECTION/DIMENSIONSFlywheel, TAPER-LOCKB B FLEXIBLE ELEMENT B FLEXIBLE ELEMENT

E

D E

D

D C A E1

C

A

D

TYPE "F" TYPE "H" TYPE "F" SIZES PF87-PF131 TYPE "H" IRON FLANGE AND CLAMP RING

TYPE "SF" TYPE "SH" STEEL FLANGE AND CLAMP RING SIZES PF172-PF252

SIZES PF172-PF192

Coupling Size PF87 PF96 PF116 PF131 PF172 PF192 PF213 PF252 Coupling Size PF87 PF96 PF116 PF131 PF172 PF192 PF213 PF252

Bushing Size 1610 2012 2517 2517 3535 4040 4545 5050 Bushing Size 1610 2012 2517 2517 3535 4040 4545 5050

Min. Bore 1/2 1/2 1/2 1/2 1-3/16 1-7/16 1-15/16 2-7/16 C Iron Flg. ..... ..... ..... ..... 7.50 8.63 ..... .....

Max. Bore 1-11/16 2-1/8 2-11/16 2-11/16 3-15/16 4-7/16 4-15/16 5-5/16

HP/100 3.00 4.50 7.10 9.50 23.00 47.00 90.00 135.00 D

Torque (In-Lbs) 1890 2835 4470 5985 14490 29610 56700 85050 E 1.34 1.58 1.39 1.95 2.31 2.56 -

E1 .... .... .... .... 3.12 3.50 4.50 5.81

PF87 THRU PF252 PART NUMBERSTAPER-LOCK Flange (1) Reqd Bolt Ring High Speed T-L Iron Flange Steel Flange Assy Element Bushing Std Flange Type H Type F Type SH Type SF (1) Reqd (1) Reqd Size PF87 010603 ..... ..... ..... ..... 011247 011227 1610 PF96 010604 ..... ..... ..... ..... 011248 011228 2012 PF116 010606 ..... ..... ..... ..... 011250 011230 2517 PF131 010607 ..... ..... ..... ..... 011251 011231 2517 PF172 ..... 011134 011154 010290 010294 011254 011234 3535 PF192 ..... 011137 011157 010291 010295 011256 011236 4040 PF213 ..... ..... ..... 010292 010296 011259 011239 4545 PF252 ..... ..... ..... 010293 010297 011262 011242 5050 Complete coupling consists of: (1) TAPER-LOCK Flange Assembly (as selected), (1) Bolt Ring Assembly, (1) High Speed Element, and (1) TAPER-LOCK Bushing. TAPER-LOCK Bushings must be ordered separately. See page PT1-40 for Flywheel & Power Take Off housing information. Coupling SizeFEATURES/BENEFITS PAGE PT1-2 EASY SELECTION PAGE PT1-17 MODIFICATION/ACCESSORIES PAGE PT1-67 ENGINEERING/TECHNICAL PAGE PT1-69

PT1-39

Fluid Couplings

FLEXIDYNE

Steel Flg. ..... ..... ..... ..... 7.00 8.50 8.75 9.50

1.00 1.25 1.75 1.75 3.50 4.00 4.50 5.00

Weight (Lbs) Less Bushing Iron Flgs Steel Flgs 9.9 ..... 13.5 ..... 22.3 ..... 33.3 ..... 87.2 77.5 128.6 128.6 221.2 190.2 297.9 260.9

Inertia (Lb-Ft2) Iron Flgs Steel Flgs 0.6 ..... 1.05 ..... 2.35 ..... 4.35 ..... 17.49 15.73 28.84 28.12 74.47 64.36 121.79 111.38

Clutches and Brakes

Max. RPM Gray Iron Steel Flange Flange 6000 6000 5230 5230 4050 4050 3750 3750 1860 2800 1620 2430 ..... 2130 ..... 1945

B A 9.44 10.31 12.31 13.81 18.31 20.31 22.50 26.50 Iron Flg. 2.69 2.83 3.14 3.70 5.81 6.56 ..... ..... Steel Flg. ..... ..... ..... ..... 6.72 7.50 9.00 10.81

Couplings



SELECTION/DIMENSIONSFlywheel, Bored To SizeB

E

D

C

A

PF87B THRU PF252B BORED-TO-SIZE FLYWHEEL COUPLINGSCoupling Size PF87B PF96B PF116B PF131B PF172B PF192B PF213B PF252B Min. Bore none none none none 2-1/4 2-1/2 2-1/2 2-7/8 Max .Bore 2-1/8 2-9/16 3-1/4 3-15/16 4-1/2 6 6-1/4 6-7/8 HP/100 3.0 4.5 7.1 9.5 23.0 47.0 90.0 135.0 Torque Max. RPM (In-Lbs) Steel Flg 1890 2835 4470 5980 14490 29610 56700 85050 6000 5230 4050 3750 2800 2430 2130 1945 A 9.44 10.31 12.31 13.81 18.31 20.31 22.50 26.50 B 3.38 3.94 4.68 5.50 6.81 8.44 9.00 10.81 C 2.94 3.69 4.94 5.44 7.00 8.50 8.75 9.50 D 1.75 2.00 2.63 3.00 3.88 5.13 4.69 5.19 E 1.63 1.94 2.00 2.50 3.13 3.50 4.50 5.81 Weight (Lbs) 10.5 14.3 24.3 33.7 84.2 129.6 188.2 250.9 Inertia (Lb-Ft2) 0.61 1.08 2.47 4.56 16.73 32.02 65.76 113.58

PF87 - PF252B PART NUMBERSBS Flange Bolt Ring High Speed Coupling Assy Assy Element Size (1) Reqd (1) Reqd (1) Reqd PF87B 010301 011247 011227 PF96B 010302 011248 011228 PF116B 010304 011250 011230 PF131B 010305 011251 011231 PF172B 010530 011254 011234 PF192B 010531 011256 011236 PF213B 010508 011259 011239 PF252B 010509 011262 011242 Complete coupling consists of: (1) BS Flange Assembly, (1) Bolt Ring Assembly, and (1) High Speed Element.FEATURES/BENEFITS PAGE PT1-2 EASY SELECTION PAGE PT1-17

SAE POWER TAKE OFF & FLYWHEEL INFO.Coupling Size PF87 PF96 PF116 PF131 PF172 PF192 PF213 PF252 Fits Within These SAE Power Take-Off Housings 6,5 4,3 4,3,2,1 3,2,1,0 0 0 0 0 SAE Flywheel Bolt Circle Diam. 8-3/4 9-5/8 11-5/8 13-1/8 17-1/4 19-1/4 21-3/8 25-1/4 Tapped Holes No. Size 8 5/16-18 6 3/8-16 8 3/8-16 8 3/8-16 8 1/2-13 8 1/2-13 6 5/8-11 12 5/8-11ENGINEERING/TECHNICAL PAGE PT1-69


PT1-40

SELECTIONNYLIGN Light Duty Flexible CouplingsThis economical, Light Duty (non-lubricated) Coupling uses a 100% Nylon sleeve and aluminum hubs. Coupling is rated 10HP @ 1750 RPM or 20 HP @3450 RPM with speeds up to 5000 RPM. Can accommodate misalignment up to 1-1/2 per side. It is lightweight, requiring no lubrication or maintenance. Hubs are available only with clearance bores and standard keyways shown in table below. Order a sleeve to go with each pair of hubs. Combinations to suit most applications can be assembled from two types of hubs.

Ambient Temperature Limit -0F to +170F

NYLIGN LIGHT DUTY PARTSHub No. Nylon Actual Key-way Sleeve Nom. Part No. +.002 -.000 1/2 148343 .501 None 5/8 148344 .626 3/16x3/32 4 3/4 148345 .751 3/16x3/32 148340 7/8 148346 .876 3/16x3/32 One Per 1 148347 1.001 1/4x1/8 1-1/8 148348 1.126 1/4x1/8 Coupling 7 1-1/4 148349 1.251 1/4x1/8 1-3/8 148350 1.376 5/16x5/32 Two required per coupling. Consists of aluminum hubs with the nish bores shown (No modication available). Hubs may be used in combinations shown in table below. One 1/4-20 setscrew furnished over keyway in each hub. Type No. Finish Bore

NYLIGN LIGHT DUTY COUPLING DIMENSIONSBore and Hub Combi- Drwg. A Keyway nations (Fig. No.) Dia No. 4 Hub, 1 1-11/16 Both Ends No. 4 Hub, See Table One End 2 1-11/16 Above No. 7 Hub, Other End No. 7 Hub 3 --Both Ends Nominal distance between shaft ends (B.S.E)FEATURES/BENEFITS PAGE PT1-2

A1 Dia. ---

B 13/16

B1 ---

C Dia. 1-15/16

D 3-1/32

E 1-3/8

E1 ---

F 1-13/32

G 9/32Fluid Couplings

2-1/4

13/16

1-7/16

1-15/16

3-21/32

1-3/8

1-1/8

1-13/32

1-5/32

2-1/4

---

1-7/16

1-15/16

4-9/32

---

1-1/8

1-13/32

2-1/32




PT1-41

FLEXIDYNE

Clutches and Brakes

Couplings



FEATURES/BENEFITSGRID-LIGNThe basic GRID-LIGN coupling consists of two steel shaft hubs, a high strength spring steel tapered grid element, two seals and a cover assembly. Misalignment and end float are accommodated by the sliding action of the grid in the lubricated hub grooves. Standard GRID-LIGN couplings operate reliably between -35 and +210F. They can accept angular misalignment to 1/2, parallel misalignment to.012, and end float to .375. Speed capability goes as high as 6000 RPM. GRID-LIGN couplings can be mounted with TAPER-LOCK bushings on shafts from 1/2 to 3-15/16. Straight bore hubs go up to 7 bore.

Flexible Tapered Element Isolates vibration, cushions shock loads Allows uniform contact during light, normal and shock loading conditions Lengthens machine life Constructed from tempered spring steel for long life

High Torque Capability Torque ranges from 422 to 230,000 in. lbs. Steel components allow for compact size

Interchangeability Stock GRID-LIGN coupling congurations include the standard full-ex design in vertically or horizontally split covers, half spacers and full spacers Interchangeable with other taper grid style couplings

PT1-42

FEATURES/BENEFITSGRID-LIGNSTYLE, SIZES AND RATINGS CHARTCoupling Styles T10 Standard Coupling H Cover T20 Standard Coupling V Cover T31 Full Spacer T35 Half Spacer Number of Sizes 13 10 8 8 Bore 7.0 5.0 4.25 4.25 Maximum Ra

Complete Catalog

Documents

textile machinery

automatic

properly sized

displacement

engineeringtechnical

withstand

national coarse

specificationnomenclature