COMPACT SCP · 2020. 7. 21. · 4 Tel Fax 0 Email seltafansco u Website eltafans co m Wiring Diagrams COMPACT SCP AC Please use the table(s) below to match up the product code and

COMPACT SCP Installation & Maintenance

These instructions must be read fully before commencing installation.

Tel 01384 275800 Fax 01384 275810 Email [email protected] Website eltafans.com2

Installation InstructionsCOMPACT SCP AC

1.0 General1.1 It is important these Installation and Maintenance Instructions are fully adhered to.1.2 Full details of the unit supplied are shown on the product nameplate. If in doubt about any detail contact Elta Fans Ltd or its agents for clarification.1.3 All electrical installation must be carried out by suitably qualified and competent personnel in accordance with all current statutory requirements.1.4 These instructions cover only the Elta Fans Ltd product and do not include the supply or installation of any safety equipment that may be required e.g. adequate guarding or protection from rotating parts and proper electrical isolation.1.5 Any declarations made by Elta Fans Ltd about product installation and safety, are dependant on the fan equipment being used within installations which themselves meet the requirements of the relevant Standards and Directives of your region.1.6 The fan is designed for use in an ambient temperature of -20°C up to a maximum of +70°C, speed controlled operating temperatures of -20°C and +50°C and up to 95% relative humidity. EC fans are designed for ambient temperatures up to +60°C. The fan is not suitable for corrosive or explosive atmospheres.1.7 The installer should provide easy access to the fan to facilitate future maintenance.1.8 The installer should ensure the fan is adequately supported.1.9 This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible for their safety. Children should be supervised to ensure that they do not play with the product.1.10 At end-of-life, the unit must be disposed of in an environmentally friendly manner by suitably qualified and competent personnel in accordance with the requirements of applicable Standards and Directives.

2.0 Installation

WARNING – The fan must be isolated from the power supply during installation and maintenance. The fan must be earthed in accordance with the local regulations.

2.1 Upon receipt, the fan equipment should be visually inspected to check for any damage. Ensure that the impeller is free to rotate.2.2 If there are any queries concerning the fan equipment, Elta Fans Ltd should be contacted prior to the installation.2.3 The fan must be securely mounted in the desired position to suit the application. The fan can be mounted at any angle.2.4 Check the details on the motor rating plate to ensure that the correct power supply (voltage, frequency and phase) is available. An incorrect power supply will lead to permanent damage to the fan motor.2.5 Refer to the appropriate wiring diagram. Ensure that all earth connections are made.2.6 Means for electrical disconnection must be incorporated in the wiring installation in accordance with the relevant wiring and electrical regulations.2.7 Precaution must be taken to locate the exhaust discharge terminal so as to avoid the backflow of gases into the room from the open flue of gas or other fuel burning appliances.

3.0 Start Up3.1 Before power is supplied to the unit, check that the wiring is correct as per the fan connection diagram.3.2 At initial start-up, check that impeller rotation and airflow direction is correct.3.3 Check that the motor amperage drawn does not exceed the nameplate rating. EC fans only:3.4 Minimum interval between consecutive starts: 5 minutes.3.5 Maximum 1 connection from power supply cycle per 5 minutes.

4.0 Fan Maintenance4.1 Inspection of the fan at least once every 12 months is recommended to ensure that the motor, fan blades, and supporting guards, are clean. Any build up of dust and deposits on the blades or guards should be removed using a non-abrasive cleaner.4.2 All fastenings should be checked for tightness. In addition, all rotating items should be checked.4.3 Bearings are of the ‘sealed for life’ type and will not need a detailed inspection.

WARNING – This fan is fitted with an auto-reset thermal contact which switches the fan off in the event of a fault condition. Once the motor cools down the fan may start unexpectedly. Only a suitably qualified and competent person may carry out maintenance after the electrical supply has been isolated.

5.0 Guarantee Elta Fans Ltd will, free of charge, within a period of 1 year from the date of dIspatch from their works, repair or at its option replace any goods which are proved to have defects as a result of defective materials or workmanship. The goods MUST be returned to Elta Fans Ltd carriage paid for examination.

Elta Fans Limited has a policy of continuous product development and improvement and therefore reserves the right to supply products which may differ from those illustrated and described in this publication. Confirmation of dimensions and data will be supplied on request. 3

COMPACT SCPInstallation Instructions

GND 10V E1

MIN MAX

E1GND

ST1

ST2

ST2

E110VGND

MAXMIN

ST1

GND E1

THE ABOVE DIAGRAM SHOWS "ST2".

"ST2" CONNECTIONS ARE FACTORY FITTED.

GND = COMMON•10V = 10VDC INPUT•E1 = 0-10VDC OUTPUT•

YOU CAN DETERMINE THE CURRENT VDC OUTPUT BYDISCONNECTING POWER TO THE UNIT, SETTING AMULTIMETER TO OHMS (Ω) AND PLACING THE TEST PROBESBETWEEN GND AND E1

PLEASE USE THE ESTIMATED ADJUSTMENT GUIDE FOR REFERENCE

THIS IS THE INTERNAL POTENTIOMETERTHIS POTENTIOMETER CAN BE ADJUSTED FOR SINGLE SPEED SETTING OR MAX SPEED SELECTION

THIS LINK/JUMPER SHOULD BE REMOVEDWHEN USING AN EXTERNAL POTENTIOMETEROR EXTERNAL CONTROL SIGNAL CONNECTEDTO "ST1"

THE ABOVE DIAGRAM SHOWS "ST1".

"ST1" CONNECTIONS ARE CLASSED AS"CUSTOMER/USER CONNECTIONS".

GND = COMMON•+ = VDC OUTPUT AS SET BY•

INTERNAL POTENTIOMETERE1 = 0-10VDC INPUT•

149-CD-POT

10/07/2018MK-149-CD-POT Issue: Saved Date:A

All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. 149-CD-POT Issue A: 10.07.2018Check the individual product accessories table for fan controller compatibility.

149-CD-POTThe 149-CD-POT is a commissiong device designed to be used with our EC range of fans. The device will allow the for the installer to set the maximum operating speed of the fan that it is connected to. The installer or commissioning engineer can adjust the fan speed using the potentiometer built onto the 149-CD-POT board. This potentionmeter can either be used for single speed adjustment or to set a maximum speed for the fan to operate at when an external control source is used. If external speed control is required, the jumper connection next to the potentionmeter on the board would need to be removed, the installer can then connect to ST1 (using the diagram provided). When an external speed control is fitted, the maximum speed setting available to the external control is limited by the potentiometer setting of the commissioning device.

EC

Please note: This is an estimated adjustment guide

149-CD-POT

The 149-CD-POT is a commissiong device designed to be used with our EC range of fans.

This device will be as standard with our box fan range from May 2018.

The device will allow the for the installer to set the maximum operating speed of the fan that it isconnected to.

The installer or commissioning engineer can adjust the fan speed using the potentiometer built onto the149-CD-POT board. This potentionmeter can either be used for single speed adjustment or to set amaximum speed for the fan to operate at when an external control source is used.

If external speed control is required, the jumper connection next to the potentionmeter on the boardwould need to be removed, the installer can then connect to ST1 (using the diagram provided).

When an external speed control is �tted, the maximum speed setting available to the external control islimited by the potentiometer setting of the commissioning device.

10/07/2018MK-149-CD-POT Issue: Saved Date:A

Level / Speed OHMS (Ω)

10 10 (Ω)

9 9 (Ω)

8 8 (Ω)

7 7 (Ω)

6 6 (Ω)

5 5 (Ω)

4 4 (Ω)

3 3 (Ω)

2 1.5 (Ω)

1 500 (Ω)

0 1 (Ω)149-CD-POT


Wiring DiagramsCOMPACT SCP AC

Please use the table(s) below to match up the product code and the wiring diagram number.

Single Phase 220V to 240V / 50Hz Three Phase 380V - 415V / 50Hz

PageNo.

Product Code

Wiring Diagram No.

6 SCP250/4-1AC 152-500

6 SCP315/4-1AC 152-500

6 SCP350/4-1AC 152-500

6 SCP500/4-1AC 152-500

6 SCP560/4-1AC 152-500

6 SCP630/4-1AC 152-500

PageNo.

Product Code

Wiring Diagram No.

7 SCP250/4-3AC 152-611

7 SCP315/4-3AC 152-611

7 SCP350/4-3AC 152-611

7 SCP400/4-3AC 152-611

7 SCP450/4-3AC 152-611

7 SCP450/4B-3AC 152-611

7 SCP500/4-3AC 152-611

8 SCP500/6-3AC 152-608

7 SCP560/4-3AC 152-611

8 SCP560/6-3AC 152-608

7 SCP630/4-3AC 152-611

8 SCP630/6-3AC 152-608

9 SCP710/4/6-3AC 152-614

9 SCP710/6/8-3AC 152-614

9 SCP800/6/8-3AC 152-614


Single Phase 220V - 277V / 50Hz or 60Hz

PageNo.

Product Code

Wiring Diagram No.

10 SCP250-1EC 152-711

10 SCP315-1EC 152-711

10 SCP350-1EC 152-711

10 SCP400-1EC 152-711

10 SCP450-1EC 152-711

10 SCP500-1EC 152-711

10 SCP560-1EC 152-711

10 SCP630-1EC 152-711

10 SCP710-1EC 152-711

Wiring Diagrams

Please use the table(s) below to match up the product code and the wiring diagram number.

COMPACT SCP EC


Wiring Diagrams152-500 AC

FAN TERMINALBOX

LINK NEEDSTO BE FITTED

TB (W

HITE

)

220 - 240V 1PH 50Hz SUPPLY

E (GR

EEN/

YELL

OW)

TB (W

HITE

)

BROW

N

BLUE

U2 (B

LACK

)

U1 (R

ED)

Z1 (B

LUE)

CAPACITOR

EL N

FIXED SPEED CONNECTION

GREE

N/YE

LLOW

BROW

N

BLUE

L/U1 N/U2TBTB AUX

Z2 (Y

ELLO

W)

THERMAL CUT - OUTCONNECT INTO

STARTER CONTROLCIRCUIT

TB (W

HITE

)

E (GR

EEN/

YELL

OW)

TB (W

HITE

)

Z2 (Y

ELLO

W)

BROW

N

BLUE

U2 (B

LACK

)

U1 (R

ED)

Z1 (B

LUE)

CAPACITOR

FAN TERMINALBOX

GREE

N/YE

LLOW

L/U1 N/U2TBTB AUX


N

CONTROLLERTERMINAL BOX

LE

GREE

N/YE

LLOW

BLUE

BROW

N

BLUE

BROW

N

BROW

N

VARIABLE SPEED CONNECTION CONTROLLER TYPE TC12, TC14, TC18, TC110, TC112

THERMAL CUT - OUTCONNECT INTO


L NN AUX EL

TB (W

HITE

)

E (GR

EEN/

YELL

OW)

TB (W

HITE

)

Z2 (Y

ELLO

W)

BROW

N

BLUE

U2 (B

LACK

)

U1 (R

ED)

Z1 (B

LUE)

CAPACITOR

FAN TERMINALBOX

L/U1 N/U2TBTB AUX

EU1TKTK L AUXU2N

BLUE

BROW

N

GREE

N/YE

LLOW

BROW

N

BROW

N

BLUE

VARIABLE SPEED CONNECTION CONTROLLER TYPE EL31TK, EL61TK

GREE

N/YE

LLOW


N


L E

ALL WIRING AND CONTROL EQUIPMENT MUST COMPLY TO THELATEST IEE REGULATIONS, IN PARTICULAR PART 552-01-02/03

02/03/2015MK-152-500 Issue: Saved Date:EAll wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-500 Issue E: 02.03.2015Check the individual product accessories table for fan controller compatibility.



GREE

N/YE

LLOW

EL1

FAN TERMINALBOX



L3L2

GREY

BLAC

K

BROW

N

W2 V1 V2 W1U2U1TBTB

THERMAL CUT-OUTCONNECT INTO


U1 U2 W1V2V1W2

L1/L U V WL3L2/N 4 5 6 731 2 8 11109

FAN TERMINALBOX

BROW

N

BLAC

K

GREY

BROW

N

BLAC

K

GREY

GREE

N/YE

LLOW

EL1


VARIABLE SPEED CONNECTION C/W 3PH - 3PH IP55/66 INVERTER

L2 L3

1 TO 7PRE - WIRED

10 RELAY COMMON11 RELAY CONTACT

3PH - 3PHIP55/66 INVERTER

ANALOG / DIGITALINPUT CONNECTIONS

TBTB

GREE

N/YE

LLOW



L1/L U V WL3L2/N 4 5 6 731 2 8 11109

ENSURE FAN IS SUITABLE FOR THIS CONNECTION.IF IN DOUBT CONTACT ELTA FANS

BROW

N

BLUE

GREE

N/YE

LLOW

EL


VARIABLE SPEED CONNECTION C/W 1PH - 3PH IP20 INVERTER

N

1PH - 3PHIP20 INVERTER


1: +24V OUTPUT2: STOP/RUN DI13: FWD/REV DI24: ANALOG/PRESET DI35: +10V OUTPUT6: ANALOG INPUT7: 0V


FAN TERMINALBOX



GREE

N/YE

LLOW

TB TB

GREY

BLAC

K

BROW

N

W2 V1 V2 W1U2U1

L1/L U V WL3L2/N 4 5 6 731 2 8 11109


1PH - 3PHIP55/66 INVERTER


1 TO 7PRE - WIRED

N

VARIABLE SPEED CONNECTION C/W 1PH - 3PH IP55/66 INVERTER


L E

GREE

N/YE

LLOW

BLUE

BROW

N

ENSURE FAN IS SUITABLE FOR THIS CONNECTION.IF IN DOUBT CONTACT ELTA FANS

FAN TERMINALBOXU1 U2 W1V2V1W2

BROW

N

BLAC

K

GREY

TBTB

GREE

N/YE

LLOW



L1/L U V WL3L2/N 4 5 6 731 2 8 11109



L3L2

VARIABLE SPEED CONNECTION C/W 3PH - 3PH IP20 INVERTER


L1 E

GREE

N/YE

LLOW

GREY

BLAC

K

BROW

N

1: +24V OUTPUT2: STOP/RUN DI13: FWD/REV DI24: ANALOG/PRESET DI35: +10V OUTPUT6: ANALOG INPUT7: 0V 3PH - 3PH

IP20 INVERTER

FAN TERMINALBOX



GREE

N/YE

LLOW

TB TB

GREY

BLAC

K

BROW

N

W2 V1 V2 W1U2U1


21/05/2015MK-152-611 Issue: Saved Date:CAll wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-611 Issue C: 21.05.2015Check the individual product accessories table for fan controller compatibility.



All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-608 Issue E: 21.06.2018Check the individual product accessories table for fan controller compatibility.DM25/06/2013

MBK0066EARTH TERMINALSRELOCATED

C

DM16/01/2013

RE-ORDERED L3, L2, L1TO L1, L2, L3 ON TOPRIGHT DIAGRAM.REPLACED TERMINALSTRIP VISUAL, WITHCONNECTION TEXT.

DMOK0041B

MB06-07-2015

REMOVED 'N (BLACK)'NOTE AND WIRE

AWMK0132D

DMO21/06/18

UPDATED WIRINGTAGS AND COLORSTO MATCHMANUFACTURING

PBK0233E

L1/L U V WL3L2/N 4 5 6 731 2 8 11109



FAN TERMINALBOX

TB (W

HITE

)

E (GR

EEN/

YELL

OW)

TB (W

HITE

)

U1 (R

ED)

V1 (Y

ELLO

W)

W1 (

BLUE

)

L3

VERIABLE SPEED CONNECTION CONTROLLER TYPE 3PH - 3PH IP20 INVERTER




L2


L1 E

GREE

N/YE

LLOW

GREY

BLAC

K

BROW

N

GREE

N/YE

LLOW

GREY

BLAC

K

BROW

N

1: +24V OUTPUT2: STOP/RUN DI13: FWD/REV DI24: ANALOG/PRESET DI35: +10V OUTPUT6: ANALOG INPUT7: 0V

TB TB W1V1U1TB TB W1V1U1



FAN TERMINALBOX

TB (W

HITE

)

E (GR

EEN/

YELL

OW)

TB (W

HITE

)

U1 (R

ED)

V1 (Y

ELLO

W)

W1 (

BLUE

)

L3

VERIABLE SPEED CONNECTION CONTROLLER TYPE 3PH - 3PH IP55 INVERTER




L2


L1 E

1 - 7 PRE WIRED

GREE

N/YE

LLOW

GREY

BLAC

K

BROW

N

GREE

N/YE

LLOW

GREY

BLAC

K

BROW

N

L2/N L3 WVUL1/L 9 10 11821 3 7654



W1 (

BLUE

)

V1 (Y

ELLO

W)

U1 (R

ED)

TB (W

HITE

)

E (GR

EEN/

YELL

OW)

TB (W

HITE

)

FAN TERMINALBOX

GREE

N/YE

LLOW

GREY

BLAC

K

BROW

N

U1 V1 W1TBTB

L3L2 EL1 U WV


EL1 L2 L3


GREE

N/YE

LLOW

GREY

BLAC

K

BROW

N

VARIABLE SPEED CONNECTION CONTROLLER TYPE TC33, TC35, TC310

W1 (

BLUE

)

V1 (Y

ELLO

W)

U1 (R

ED)

TB (W

HITE

)



L1 L2 L3

E (GR

EEN/

YELL

OW)

TB (W

HITE

)

FAN TERMINALBOX

E


GREE

N/YE

LLOW

GREY

BLAC

K

BROW

N


U1 V1 W1TBTB

A3A3152-608

NTS

C

DRAWING No.

SHEET OF ISSUE

DRAWN BY

DATE

SCALE STATUS

APPROVED

CHECKEDELTA FANS LTD,17 BARNES WALLIS ROAD,SEGENSWORTH INDUSTRIAL ESTATE,FAREHAM, HAMPSHIRE. PO15 5ST.Tel. 01489 566500 Fax. 01489 566555

Elta Fans Ltd. own the copyright of this drawing/

in writing from its owners Elta Fans Ltd.and must not be reproduced without permission

con�dence and which must not be used for anyspeci�cation document which is supplied in

C

FINISH

DIMENSIONS ARE IN mm UNLESS STATED OTHERWISE

BYISS CN.

DATE CHKD

ISS CN. BY

DATE CHKD

ISS CN. BY

DATE CHKD

ISS CN. BY

DATE CHKD

A C D E

1 1 E

24-11-11

PG

PB

Ipurpose other than that for which it is supplied

B

1010 N/A

AWM


AC

All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-614 Issue B: 29.04.2015Check the individual product accessories table for fan controller compatibility.

Wiring Diagrams152-614



GREE

N/YE

LLOW

EL1

FAN TERMINALBOX


LOW SPEED CONNECTION(STAR CONFIGURATION)

L3L2

GREY

BLAC

K

BROW

N

W2 V1 V2 W1U2U1TBTB

V2 (O

RANG

E)

W1 (

BLUE

)

U2 (B

LACK

)

V1 (Y

ELLO

W)

W2 (

WHI

TE)

U1 (R

ED)

E (GR

EEN/

YELL

OW)

TB (B

LACK

& W

HITE

)

TB (B

LACK

& W

HITE

)

V2V1W2 W1U2U1TBTB

1: +24V OUTPUT2: STOP/RUN DI13: FWD/REV DI24: ANALOG/PRESET DI35: +10V OUTPUT6: ANALOG INPUT7: 0VBR

OWN

BLAC

K

GREY

GREE

N/YE

LLOW

BROW

N

BLAC

K

GREY GR

EEN/

YELL

OW

EL1


L2




VARIABLE SPEED CONNECTION CONTROLLER TYPE 3PH - 3PH IP20 INVERTER

L3



9 10 11821 3 7654L2/N L3 WVUL1/L

4 5 6 731 2 8 11109L1/L U V WL3L2/N

BROW

N

BLAC

K

GREY

GREE

N/YE

LLOW

BROW

N

BLAC

K

GREY GR

EEN/

YELL

OW

1 - 7 PRE WIRED

EL1


L2




VARIABLE SPEED CONNECTION CONTROLLER TYPE 3PH - 3PH IP55 INVERTER

L3



TB TB U1 U2 W1W2 V1 V2

GREE

N/YE

LLOW

EL1

FAN TERMINALBOX


HIGH SPEED CONNECTION(DELTA CONFIGURATION)

L3L2

GREY

BLAC

K

BROW

N

W2 V1 V2 W1U2U1TBTB

V2 (O

RANG

E)

W1 (

BLUE

)

U2 (B

LACK

)

V1 (Y

ELLO

W)

W2 (

WHI

TE)

U1 (R

ED)

E (GR

EEN/

YELL

OW)

TB (B

LACK

& W

HITE

)

TB (B

LACK

& W

HITE

)




29/04/2015MK-152-614 Issue: Saved Date:B


Wiring Diagrams152-711

All wiring and control equipment must comply to the latest IEE regulations, in particular part 552-01-02/03. MK-152-711 Issue C: 15.01.2019Check the individual product accessories table for fan controller compatibility.

0-10V DC INPUT (IF REQUIRED)

GND 0-10 VDC

ALL WIRING AND CONTROLS EQUIPMENT MUST COMPLY TO THELATEST IET REGULATIONS, IN PARTICULAR PART 552-01-02/03

15/01/2019MK-152-711 Issue: Saved Date:C

5

NOTE: TAG REFERENCES RELATE TO MOTOR CONTROL WIRES, AND NOT 149-POT-10

65

BLACK

BROWN

JUMPERREMOVED *

MAX SPEEDTRIMMER

PENL

POW

ERCO

NTRO

LS

RED

BLUE

WHITE

YELLOW

G/Y

BLUE

BROWN

220 - 277V 1PH 50HzMAINS SUPPLY

LN

SINGLE FAN

1PH EC SINGLE FAN C/W 149-CD-POT & 149-POT-10

BLUEBROW

N

GREE

N/YE

LLOW

GND 10V E1

MIN MAX

E1GND

ST1

ST2

149-CD-POT

23

41

FOR USE WITH:SCP250-1ECSCP315-1ECSCP350-1ECSCP400-1ECSCP450-1ECSCP500-1ECSCP560-1ECSCP630-1ECSCP710-1EC

65

BLACK

BROWN

REMOVE LINK WHEN USINGEXTERNAL POTENTIOMETER OREXTERNAL CONTROL SIGNAL

POTENTIOMETER FOR SINGLESPEED ADJUSTMENT OR MAXSPEED SELECTION

PENL

POW

ERCO

NTRO

LS

RED

BLUE

WHITE

YELLOW

G/Y

BLUE

BROWN

220 - 277V 1PH 50HzMAINS SUPPLY

LN

SINGLE FAN

1PH EC SINGLE FAN C/W 149-CD-POT & 0-10VDC INPUT

BLUE

BROW

N

GREE

N/YE

LLOW

GND 10V E1

MIN MAX

E1GND

ST1

ST2

149-CD-POT

23

41

FOR USE WITH:SCP250-1ECSCP315-1ECSCP350-1ECSCP400-1ECSCP450-1ECSCP500-1ECSCP560-1ECSCP630-1ECSCP710-1EC

149-POT-10

2 7 61

NOTE:*JUMPER REMOVED WHEN EXTERNALCONTROL SOURCE IS USED.

Tag Purpose Description

L Live Live power supply, 220-277V

N Neutral Neutral from power supply

Permanent Earth Permanent earth from power supply

1 DC Voltage [2-10V] DC control voltage input(2 to 10VDC input)2 DC Current [4-20mA] DC control current input(4 to 20mA input)

3 Frequency [10-95%]Frequency duty-cycle (PWM)

Voltage: 10 to 24VpkFrequency: 80Hz(10 to 95% input)

4 Speed Reference Tacho output

5 10VDC output 10VDC source output

6 GND / Common DC Common

EC


EC Declaration of Conformity EC Declaration of Incorporation

Description of Equipment:Building Services Ranges - Air movement fan

Equipment model numbers for safe area fans:SCP, SPA, SAX, SCD, SDA, SCC, SLC, SCPP, SPP, SAMF, HIT, SEM, SEL, ISEO IMF, SH, SSD, SQS, SQSDCV, SQU, SMB, STD, SQT, SQT-DCV, SCH, SCHT, SSDR, SSDRDCV, STDR, STDRDCV, SB, SQU-HT, SSQU-HT, SDF, ZFHIC, SRC, CF, TF

Relevant / applied directives:Machinery directive 2006/42/EC, Low voltage directive 2014/35/EU

Relevant / applied directives where applicable:Energy related products directive 2009/125/EC (when used in Europe) Electromagnetic compatibility directive 2014/30/EU (where driven via Inverter)

Relevant / applied directives where applicable:BS EN ISO 12100 : 2010BS EN 14694 : 2003 + A1 : 2011BS EN 308:1997BS EN ISO 5801:2008

In accordance with the Machinery Directive 2006/42/EC;

The design of the partly completed machine, listed above, complies with the Essential Health and Safety Requirements (EHSRs) of ANNEX I, sections 1.1.2, 1.1.5, 1.4.1, 1.5.1 in EC Machinery Directive 2006/42/EC.

Machinery is incomplete and must not be put into service until such time as the machinery which is partly complete, is to be incorporated, and has been assessed and Declared in Conformity with the provi-sions of any relevant parts of the Machinery Directive.

We undertake to transmit, upon reasoned request by appropriate na-tional authorities, relevant information relating to the partly completed machinery identified above.

Manufacturer:Elta Fans Limited46 Third AvenuePensnett Trading EstateKingswinfordWest MidlandsDY6 7USUnited Kingdom

Date / Signature of Manufacturer: Document last revised: 28th March 2017

Name / Position of Signatory: Mr. Robert Rees Q.A.Manager Elta Fans LtdThis is an electronic document and is valid without a signature or date. Issue Status B

Herewith we declare that the air movement equipment below, on the basis of its design and construction as partly completed machines brought onto the market complies with relevant health and safety requirements of the EC Directives stated below. In the event that alterations are made to the machinery without prior consent from Elta Fans Ltd, this declaration becomes invalid.

EC Declaration of conformity/incorporation

535-IOM0015 Issue D

eltafans.com

Tel +44 (0) 1384 275800Fax +44 (0) 1384 275810Email [email protected]

46 Third Avenue, Pensnett Trading Estate, Kingswinford, West Midlands, DY6 7US United Kingdom

Tel +44 (0) 1489 566500Fax +44 (0) 1489 566555Email [email protected] / [email protected]

17 Barnes Wallis Road, Segensworth East Industrial Estate, Fareham, Hampshire, PO15 5ST United Kingdom

Applied Technology & Building Services Export

Building Services

BS EN ISO 9001:2015 FM 556465

A member ofHEVAC ASSOCIATION

COMPACT SCP · 2020. 7. 21. · 4 Tel Fax 0 Email seltafansco u Website eltafans co m Wiring Diagrams COMPACT SCP AC Please use the table(s) below to match up the product code and

Documents