Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. Catalog No. 04-56480002-01 Printed in U.S.A. Form 48/50A-3W Pg 1 508 4-08 Replaces: New Wiring Diagrams INDEX ACCESSORIES NOTE: Accessory wiring is shown on the unit wiring diagrams. Refer to the appropriate drawing for accessory wiring. TYPE UNIT NUMBER FIG. NO. Component Arrangement 48/50A2,A3,A4,A5020-035 48EJ502489 1 48/50A2,A3,A4,A5040-060 48EJ503652 2 Power Schematic 48/50A2,A3,A4,A5020-050 50EJ500470 3 48/50A2,A3,A4,A5060 RTPF 50EJ500469 4 48/50A2,A3,A4,A5060 MCHX 50EJ500420 5 Main Control Box Circuit 48/50A2,A3,A4,A5020-060 50EJ500440 6 Auxiliary Control Box Wiring 48/50A2,A3,A4,A5020-060 48EJ503076 7 Controls Expansion Board Wiring 48/50A2,A3,A4,A5020-060 48EJ503086 8 Gas Heat Control Circuit (2-Stage Heat) 48A2,A3,A4,A5020-050 48EJ503079 9 48A2,A3,A4,A5060 48EJ503679 10 Gas Heat Control Circuit (Staged Gas Heat) 48A2,A3,A4,A5020-050 48EJ502488 11 48A2,A3,A4,A5060 48EJ503680 12 Electric Heat Control Circuit 50A2,A3,A4,A5020-050 48EJ503080 13 50A2,A3,A4,A5060 48EJ503655 14 ACCESSORY UNIT FIG. NO. Motormaster® V Low Ambient Controller 48/50A2,A3,A4,A5020-035 15 48/50A2,A3,A4,A5040,050 AND 060 RTPF Units 16 48/50A2,A3,A4,A5060 MCHX Units 17 Space Sensor Temperature Averaging 48/50A2,A3,A4,A5020-060 18 Thermostat 48/50A2,A3,A4,A5020-060 6 Remote Economizer Position Override Remote Economizer Minimum Position Set Point Remote 4 to 20 mA Economizer Position Space IAQ Sensor Outdoor Enthalpy Changeover Sensor 48/50A2,A3,A4,A5020-060 7 Differential Enthalpy Changeover Sensor Outdoor Air Quality Sensor 48/50A2,A3,A4,A5020-060 8 Remote Supply Air Set Point Demand Limit Controller Fan Status Switch Demand Limit Fire Pressurization Fire Evacuation Fire Smoke Purge IAQ Override Switch WEATHERMAKER ® 48/50A2,A3,A4,A5020-060 Single Package Rooftop Gas Heating/Electric Cooling and Electric Cooling Units with COMFORTLINK™ Controls
28
Embed
COMFORT Wiring Diagrams Control Box Circuit 48/50A2,A3,A4,A5020-060 50EJ500440 6 Auxiliary Control Box Wiring 48/50A2,A3,A4,A5020-060 48EJ503076 7 Controls Expansion Board Wiring...
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.Catalog No. 04-56480002-01 Printed in U.S.A. Form 48/50A-3W Pg 1 508 4-08 Replaces: New
Wiring DiagramsINDEX
ACCESSORIES
NOTE: Accessory wiring is shown on the unit wiring diagrams. Referto the appropriate drawing for accessory wiring.
Electric Heat Control Circuit50A2,A3,A4,A5020-050 48EJ503080 13
50A2,A3,A4,A5060 48EJ503655 14
ACCESSORY UNIT FIG. NO.
Motormaster® V Low Ambient Controller48/50A2,A3,A4,A5020-035 15
48/50A2,A3,A4,A5040,050 AND 060 RTPF Units 1648/50A2,A3,A4,A5060 MCHX Units 17
Space Sensor Temperature Averaging 48/50A2,A3,A4,A5020-060 18Thermostat
48/50A2,A3,A4,A5020-060 6Remote Economizer Position OverrideRemote Economizer Minimum Position Set PointRemote 4 to 20 mA Economizer PositionSpace IAQ SensorOutdoor Enthalpy Changeover Sensor
48/50A2,A3,A4,A5020-060 7Differential Enthalpy Changeover SensorOutdoor Air Quality Sensor
48/50A2,A3,A4,A5020-060 8
Remote Supply Air Set PointDemand Limit ControllerFan Status SwitchDemand LimitFire PressurizationFire EvacuationFire Smoke PurgeIAQ Override Switch
WEATHERMAKER®
48/50A2,A3,A4,A5020-060Single Package Rooftop
Gas Heating/Electric Cooling and Electric Cooling Unitswith COMFORTLINK™ Controls
2
ELECTRIC HEAT POWER DIAGRAMS
NOTE: All power leads connect to (single) TB7 power terminal block.There are 2 or 3 conductors per terminal.
LEGEND AND NOTES FOR FIG. 1-14
UNIT SIZES50A2,A3,A4,A5 ELECTRICAL CHARACTERISTICS
NOMINAL kWFIG. NO. QTY PER UNIT
Lo Heat Hi Heat
020-050
208/230-3-60 36 72 19 2460-3-60380-3-60
3624
7249 19 2
575-3-60 36 72 19 2
060
208/230-3-60 54 108 19 3460-3-60380-3-60
5437
10874 19 3
575-3-60 54 108 19 3
LEGEND
AUX — AuxiliaryBP — Building PressureC — Contactor, CompressorCAP — CapacitorCB — Circuit BreakerCBOX — Control BoxCCB — Control Circuit BreakerCCH — Crankcase HeaterCCN — Carrier Comfort Network®
CEM — Controls Expansion ModuleCOMP — Compressor MotorCS — Compressor SafetyCSB — Current Sensing BoardCV — Constant VolumeDP — Duct PressureDPT — Discharge Pressure TransducerDS — Disconnect SwitchECB — Economizer Control BoardECM — Economizer MotorEDT — Evaporator Discharge Temperature SensorEMM — Energy Management ModuleFIOP — Factory-Installed OptionFS — Flame SensorFU — FuseGND — GroundHC — Heater ContactorHGBP — Hot Gas BypassHPS — High-Pressure SwitchHR — Heater RelayHS — Hall Effect SensorIAQ — Indoor Air QualityIDM — Induced Draft MotorIFC — Indoor Fan ContactorIFCB — Indoor Fan Circuit BreakerIFM — Indoor Fan MotorIGC — Integrated Gas Unit ControllerIP — Internal ProtectorLAT — Leaving Air Temperature SensorLEN — Local Equipment NetworkLS — Limit SwitchMBB — Main Base BoardMGV — Main Gas ValveNEC — National Electrical CodeOARH — Outdoor-Air Relative HumidityOAT — Outdoor-Air Temperature SensorOFC — Outdoor Fan ContactorOFM — Outdoor Fan MotorPEC — Power Exhaust ContactorPEM — Power Exhaust MotorPL — Plug AssemblyRARH — Return Air Relative HumidityRAT — Return Air Temperature SensorREM/OCC — Remote OccupancyRLA — Rated Load AmpsRS — Rollout SwitchSCB — Staged Gas BoardSCT — Saturated Condensing Temperature SensorSDU — Scrolling Marquee Display UnitSPT — Suction Pressure TransducerSST — Saturated Suction Pressure TransducerTB — Terminal BlockTRAN — TransformerVAV — Variable Air VolumeVFD — Variable Frequency Drive
Terminal Block
Terminal (Unmarked)
Terminal (Marked)
Splice
Factory Wiring
Field Wiring
To indicate common potential only, not to represent wiring.
To indicate FIOP or Accessory
Common
PLUG LOCATION REFERENCE
NOTES:1. Factory wiring is in accordance with the national electrical codes. Any field
modifications or additions must be in compliance with all applicable codes.2. Use 75° C min wire for field power supply, use copper wires for all units.3. All circuit breakers “Must Trip Amps” are equal to or less than 156% RLA.4. Compressor and fan motors are thermally protected — three phase motors
protected against primary single phase conditions.5. Red jumper wire must be added between R and WI for Space Temperature
mode and temporarily during Service Test mode when the heaters need tooperate.
NAME LOCATION DESCRIPTIONPL1 MAIN CB Communications from MMB to PL5/PL4PL2 MAIN CB Smoke Detector and 24V from TB5 to AUX CBOXPL3 MAIN CB Heat Control and 24V from MBB to PL9PL4 MAIN CB Communications from OL1 to SCB/EMMPL5 AUX CB Communications from PL1 to ECB1 & ECB2PL6 AUX CB REM/OCC from PL7 to ECB1PL7 MAIN CB REM/OCC from TB5/6 to PL6/12PL8 AUX CB ECM Control from PL12 to ECB1PL9 ELEC HEAT Control from PL3 to IGC/HR/PL14PL10 GAS HEAT IDM Line Voltage from PL11 to IDM(CAP)PL11 MAIN CB Line Voltage from OFC2 to PL10 (IDM)PL12 AUX CB Branch from PL2,7,8 to PL13,18,19,20PL13 AUX CB Smoke Det. Control from PL12 to Smoke Det.PL14 ELEC HEAT Control Power to Heater Box 1PL15 ELEC HEAT Control Power to Heater Box 2PL16 ELEC HEAT Control/Signal from PL12 to EconomizerPL18 AUX CB Control/Signal from PL12 to CO2 SensorPL19 AUX CB Control/Signal from PL12 to EconomizerPL20 AUX CB 24V Power from PL12 to ECB1/ECB2PL21 AUX CB 24V Power from PL20 to ECB1/PECPL22 MAIN CB Line Voltage from CCB to PECPL23 AUX CB Pwr. Exh. from PEC to PL24,25,26,27PL24 AUX CB PEM Pwr. from PL23PL25 AUX CB PEM Pwr. from PL23PL26 AUX CB PEM Pwr. from PL23PL27 AUX CB PEM Pwr. from PL23PL28 MAIN CB Thermistor Input from MMB to PL29/PL30PL29 EVAP SECT SAT HarnessPL30 AUX CB OAT/RAT HarnessPL31 MAIN CB HPS/SSTPL33 MAIN CB Crankcase HeatersPL34 MAIN CB SCTPL35 EVAP SECT Hot Gas Bypass Harness
3
SEQUENCE OF OPERATION
Constant Volume (CV) Units — On power up, thecontrol module will activate the initialization software. Theinitialization software will determine the unit configuration andalso initialize any controls loops and input/output devices. Allalarms and configurations are saved in memory and maintainedduring power outages. All alarms will be maintained inmemory and must be cleared through the scrolling marqueedisplay.
The unit can be configured with two different control types:thermostat control or space temperature sensor control.THERMOSTAT CONTROL — If the unit is equipped with athermostat with Y1, Y2, W1, W2 and G connections, then thecontrol will perform the following sequence.
When terminal G is energized, the indoor fan will turn on.The fan must be running for heating or cooling to occur. If Y1is closed (first stage of cooling is energized), then the unitcontrol will first check the ability to use the economizer. If theeconomizer can be used, then the unit control will modulate thedamper open to maintain the low-load economizer leaving airtemperature set point.
If Y2 closes (second stage of cooling is energized), then theunit control will lower the leaving air temperature set point tothe configured set point. If the economizer cannot satisfy theload, then the compressors will be sequenced on to maintaineither the low or high load temperature set points. If theeconomizer cannot be used or the enable control disables theeconomizer, then the control will sequence the compressorsbased on the Y1 and Y2 signals.
If two-stage control has been selected, then the unit controlwill map the compressors to the Y1 and Y2 inputs (first andsecond stage cooling) as defined in the loading sequence. IfAdaptive mode has been selected, then the control will add andremove compressor stages to maintain the high and lowdemand set points. If Y1 is closed (first stage of coolingenergized), at least one compressor stage will be turned on.
If W1 closes (first stage of heating is energized), then theunit will be in the Heating mode. The economizer will beclosed to the minimum position. If the unit is equipped withgas or electric heat, then the first stage of heat will beenergized. If W2 closes, then the unit control will turn on thesecond stage of heat. If the unit is equipped with a staged gasheat control option, then the W1 and W2 signal will be used tocontrol the gas heat to the configurable low and high heat loadleaving air temperature set points. If the unit is equipped withgas heat, then the integrated gas control (IGC) board will con-trol the operation of the gas heat. See the Gas Heat Unit Opera-tion section for the IGC board sequence of operation.SPACE TEMPERATURE SENSOR CONTROL — If spacetemperature operation has been selected using a T55, T56, orT58 sensor, then a wire jumper must be added between R, W1,and W2. If a remote occupancy control method has beenselected, then the remote occupancy input must first be closedfor the unit to go into heating, vent, or cooling modes. If theinternal timeclock is used, the unit control module determinesthe occupancy state based on the system time schedules.
If Temperature Compensated Start is active, the unit willbe controlled as in the occupied mode. The TemperatureCompensated Start function will start the unit before thescheduled occupied time (as determined by prior operation) tobring the space to the set point temperature when occupiedtime starts. As an example, if the unoccupied set point is 60 F,the occupied set point is 72 F, and the occupied time periodstarts at 8:00 AM, the Temperature Compensated Start functionwill bring on the unit at 7:45 AM (as determined from previousoperation) so the room temperature will be at 72 F when theoccupied time starts.
If the unit has been configured for a pre-occupancy purge,then the control will start the unit in Vent mode prior to theoccupancy time to vent the space. If an IAQ (indoor air quality)sensor is being used and the low IAQ set point is satisfied, thenthe occupancy Purge mode will be terminated.
The set points for heat and cooling are configurable throughthe scrolling marquee display.NOTE: If a T56 sensor is being used, then the slide bar on thesensor can offset the set point by has much as 5 degrees.
If the space temperature rises above the cooling set point,then the unit will go into Cooling mode. If the economizer canbe used, the control will first try to control to the LeavingAir Temperature set point. The set point will depend on thespace temperature. If the temperature is above the LowDemand set point, then the Low Economizer Load DischargeAir Temperature set point will be used. If the temperature isabove the High Load Space Temperature set point, then theHigh Load Leaving Air Temperature set point will be used. Ifthe economizer cannot satisfy the load the compressors willbe sequenced on to maintain either the low or high loadtemperature set points. If the economizer cannot be used or theunit control disables the economizer, then the unit control willsequence the compressors based on the low and high loadspace temperature variables. If two-stage control has beenselected then the control will map the compressors to the lowand high loads as defined in the loading sequence. If Adaptivemode has been selected then the control will add and removecompressors stages to maintain the low and high demandleaving air set points.
If the load goes below the heating space temperature setpoints, the Heating mode will initiate. The economizer will beclosed to the minimum position and (if the unit is equippedwith gas or electric heat) the first stage of heat will beenergized. If the space temperature goes below the High LoadSpace Temperature set point then the control will turn on thesecond stage of heat. If the unit is equipped with a staged gasheat control option then the low load and high load demandsignal will control the Leaving Air Temperature set point andwill turn on heating stages to maintain the Leaving AirTemperature set points.
If the unit is configured for unoccupied free cooling,mechanical cooling, or heating and the room temperature goesabove or below the unoccupied configuration set points, thenthe unit control will turn on free cooling, mechanical cooling,or heat as needed to return room temperature within theunoccupied set points. When in this mode, the economizerdampers will be maintained fully closed or to the minimumunoccupied ventilation set point.
Variable Air Volume Control — On power up, thecontrol module will activate the initialization software. Theinitialization software will determine the unit configuration andalso initialize any control loops and input/output devices. Allalarms and configurations are saved in memory and maintainedduring power outages. All alarms will be maintained inmemory and must be cleared through the scrolling marqueedisplay.
The unit will first determine the mode of operation. If theunit has been configured for space temperature demand thenthe control will determine, based on the configurable set points,if the unit should be in the Heating mode, Vent mode or Cool-ing mode. If the unit is configured for return air temperaturecontrol, then the unit control will start the fan and monitor thereturn air temperature against the configurable set point todetermine if the unit should be in Cooling, Vent or Heatingmode.
4
If the control is connected to a ComfortID™ system, theroom terminals are equipped with microprocessor controls thatgive commands to the base module. If linkage is active, thecontrol module will replace local ComfortLink™ set pointsand occupancy data with linkage supplied data.
If Temperature Compensated Start is active, then the unitcontrol will start the unit in advance of the occupied time topre-cool or heat the space. If the unit is configured to use apre-purge cycle, then the control will start the unit in vent modebased on a pre-start time interval. If an IAQ (indoor air quality)sensor is being used and the low IAQ control point is satisfiedthen the mode will be terminated. The mode terminates whenthe occupied period starts.
If Cooling mode is required, then the controlling set pointwill be the leaving evaporator air temperature set point. If aneconomizer is present and the changeover control allows theeconomizer to be used, then the control will first attempt tocontrol the leaving evaporator air temperature using freecooling. If this cannot satisfy the load then additionalcompressor stages will be turned on to maintain the leaving airtemperature. When both compressors and the economizer arebeing used, the unit control will use the economizer dampers tomaintain better control of the leaving air and to prevent highcompressor cycling. If the economizer cannot be used, then itwill be set to the minimum vent position.
If the unit is equipped with an optional hot gas bypass valve,then the unit control will use hot gas as an additional stage ofcapacity. When the first stage of cooling is required, the unitcontrol will turn on the circuit A compressor and the hot gasbypass valve. When additional cooling is called for, the unitcontrol will turn off the hot gas bypass valve. The valve willalso be used for additional freeze protection of the coils whenlow evaporator refrigerant temperatures are detected using thesuction pressure tranducers.
The unit control will also monitor the supply duct pressureand send a 4 to 20 mA signal to the factory-supplied inverter tocontrol the speed of the fan to maintain the user-configuredsupply duct status pressure. If the ComfortLink control is onthe CCN (Carrier Comfort Network®) system or a buildinglinkage system, then the control also supports static pressurereset based on the needs of the zones.
If the unit has been enabled for occupied heat and if thespace temperature sensor (SPT), return air temperature sensor(RAT), or CCN (in a building linkage system) demand requiresthat the unit be in Heating mode, then the unit control willenergize the electric or gas heat to warm the space. In thismode, the unit control will energize the heat interlock relay(HIR). Note that for the linkage systems the interlock relayconnection is not required. Once the mode is enabled, the unitcontrol will use up to 2 stages of heat to control to the return airtemperature set point. Heating will continue until the returntemperature set point is satisfied. If the unit is configured formorning warm-up and the heating demand is below the setpoint during the first 10 minutes of operation, then the unitcontrol will energize full heating capacity until the return airtemperature set point is satisfied.
Gas Heat Unit Operation — The gas heat units incor-porate 2 (3 on size 060) separate systems to provide gas heat.Each system incorporates its own induced-draft motor,Integrated Gas Control (IGC) board, 2-stage gas valve,manifold, and safeties. The systems are operated in parallel.For example, when there is a call for first stage heat, bothinduced-draft motors operate, both gas valves are energized,and both IGC boards initiate spark. All of the gas heatingcontrol is performed through the IGC boards (located in theheating section).
The MBB (Main Base Board) module board initiates andterminates heating operation and monitors the status of therequirements for indoor fan operation. The fan will becontrolled directly by the MBB board.
When the thermostat or room sensor calls for heating, theMBB board will close heating relays and send power to W oneach of the IGC boards. An LED on the IGC board will be onduring normal operation. A check is made to ensure that therollout switches and limit switches are closed and the induced-draft motors are not running. After the induced-draft motors areenergized and speed is proven with the Hall Effect sensor onthe motor, the ignition activation period begins. The burnerswill ignite within 5 seconds. When ignition occurs the IGCboard will continue to monitor the condition of the rollout andlimit switches, the Hall Effect sensor and the flame sensor.
If the unit is controlled through a room thermostat set forfan auto., 45 seconds after ignition occurs the indoor-fan motorwill be energized and the outdoor-air dampers will open to theirminimum position. If the overtemperature limit opens prior tothe start of the indoor-fan blower, on the next attempt the45-second delay will be shortened to 5 seconds less than thetime from initiation of heat to when the limit tripped. Gas willnot be interrupted to the burners and heating will continue.Once modified, the fan on delay will not change back to45 seconds unless power is reset to the control.
If the unit is controlled through a room sensor, the indoorfan will operate in the occupied mode and the outdoor-airdampers will be at the minimum position. In the unoccupiedmode, the indoor fan will be energized through the IGC boardwith a 45-second delay and the outside-air dampers will moveto the minimum unoccupied set point.
When additional heat is required, the second stage MBBoutput relay closes and initiates power to the second stage of allmain gas valves in all sections. When the demand is satisfied,MBB heat output relays will open and the gas valves closeinterrupting the flow of gas to the main burners.
If the call for stage 1 heat lasts less than 1 minute, theheating cycle will not terminate until 1 minute after W1became active. If the unit is configured for intermittent fan thenthe indoor-fan motor will continue to operate for an additional45 seconds then stop and the outdoor-air dampers will close. Ifthe over temperature limit opens after the indoor motor isstopped within 10 minutes of W1 becoming inactive, on thenext cycle the time will be extended by 15 seconds. Themaximum delay is 3 minutes. Once modified, the fan off delaywill not change back to 45 seconds unless power is reset to thecontrol.
Indoor Air Quality — The indoor air quality (IAQ) func-tion provides a demand-based control for ventilation air quanti-ty, by providing a modulating outside air damper position thatis proportional to space CO2 level. The ventilation damper po-sition is varied between a minimum ventilation level (based oninternal sources of contaminants and CO2 levels other than theeffect of people) and the maximum design ventilation level(determined at maximum populated status in the building).During a less-than-fully populated space period, the CO2 levelwill be lower than maximum design ventilation level at full-load design condition, thus less ventilation air will be required.Reduced quantities of ventilation air will result in reduced op-erating costs. Space CO2 level is monitored and compared touser-configured set points. An accessory CO2 sensor for space(or return duct mounting) is required. The IAQ routine can beenhanced by also installing a sensor for outdoor air quality(OAQ).
5
During the occupied period in the absence of a demand forcooling using outside air, if CO2 level is below the set point forthe minimum ventilation level, the outside-air damper will beopened to and maintained at the minimum ventilation leveldamper position set point.
When the space CO2 level exceeds set point for the mini-mum ventilation level condition, the ComfortLink™ controlswill begin to open the outside air damper position to admitmore ventilation air and remove the additional contaminants.As the space CO2 level approaches the set point for maximumdesign ventilation level condition, the outside air damperposition will reach the maximum ventilation level damperposition set point limit. Damper position will be modulated in adirectly proportional relationship between these two CO2 setpoint limits and their corresponding damper position limits.
In most applications a fixed reference value can be set forthe outdoor air quality level, but the control also supports theaddition of an outside air quality sensor that will then becompared to the indoor or return IAQ sensor. If an OAQ sensoris connected, the demand set point levels will be adjustedautomatically as the outdoor CO2 levels vary. Also, if theoutdoor CO2 level exceeds a user-configured maximum limitvalue, then outside air damper position will be limited to theminimum ventilation damper set point value. The unit controlcan also receive these signals through the Carrier ComfortNetwork® (CCN) system.
The IAQ and OAQ measurement levels are displayed bythe ComfortLink controller in parts per million (ppm).
INPUT/OUTPUT CHANNEL DESIGNATIONS — MAIN BASE BOARD (MBB)
POINT NAME POINT DESCRIPTION I/O POINT
NAMEPLUG AND PIN REFERENCE SIGNAL PIN(S) PORT STATE
INPUTSGASFAN YAC Indoor Fan relay (fan request from YAC) DI1 J6, 3-4 4 0 = 24vac, 1= 0vac
TB-5 - FIELD CONNECTIONS (HY84HA101) (in Main Control Box)
TB5
1 VAV Heater Interlock Relay, Ground Dry Contact, Max 1 Amp2 VAV Heater Interlock Relay, 24 VAC Dry Contact, Max 1 Amp3 T55/T56 10 K Thermistor Thermistor Input4 T55/T56 10 K Thermistor Thermistor Input5 T56 Set Point Adjustment (100 K ohm) Thermistor Input6 Indoor Air IAQ Remote Sensor/Remote Pot/Remote 4-20 mA 4-20 mA, ext. powered w/res or 0-5 VDC, +7 Indoor Air IAQ Remote Sensor/Remote Pot/Remote 4-20 mA 4-20 mA, ext. powered w/res or 0-5 VDC, –8 Smoke Detector Remote Alarm external contacts9 Smoke Detector Remote Alarm external contacts
10 Fire Shutdown 24 VAC Power11 Fire Shutdown 24 VAC Input12 Fire Control* 24 VAC Power13 Fire Pressurization* 24 VAC Input14 Fire Evacuation* 24 VAC Input15 Fire Smoke Purge* 24 VAC Input16 Not Used —
TB-6 - FIELD CONNECTIONS (HY84HA101) (in Main Control Box)
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.Catalog No. 04-56480002-01 Printed in U.S.A. Form 48/50A-3W Pg 28 508 4-08 Replaces: New