COLOR MONITOR SERVICE MANUAL Website:http://biz.LGservice.com E-mail:http://www.LGEservice.com/techsup.html CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. MODEL: S7500 (PE1165T), S7500 (PE1165), MV7500 (PE1165U), MV7500 (PE1165), CV7500 (PE1165U) CHASSIS NO. : CA-110 FACTORY MODEL: CQ771G *( ) ID LABEL Model No.
34
Embed
COLOR MONITOR SERVICE MANUAL - Diagramas dediagramas.diagramasde.com/otros/Service Manual - Compaq...associated flyback and yoke circuits. FIRE & SHOCK HAZARD An isolation transformer
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
BLOCK DIAGRAM ................................................... 7DESCRIPTION OF BLOCK DIAGRAM................... ..8
ADJUSTMENT ...................................................... 10TROUBLESHOOTING GUIDE .............................. 12EXPLODED VIEW................................................... 22REPLACEMENT PARTS LIST ............................... 24PIN CONFIGURATION........................................... 29PACKING AND ACCESSORIES ............................ 31SCHEMATIC DIAGRAM......................................... 32PRINTED CIRCUIT BOARD................................... 34
SPECIFICATIONS
MODE
FULL POWER
STAND-BY
SUSPEND
POWER OFF
POWER CONSUMPTION
less than 100 W
less than 5 W
less than 5 W
less than 5 W
LED COLOR
GREEN
AMBER
AMBER
OFF
SAFETY-RELATED COMPONENT WARNING!There are special components used in this color monitorwhich are important for safety. These parts are marked
on the schematic diagram and the replacementparts list. It is essential that these critical parts should bereplaced with the manufacturer's specified parts toprevent X-radiation, shock, fire, or other hazards. Do notmodify the original design without obtaining writtenpermission from manufacturer or you will void the originalparts and labor guarantee.
CAUTION: No modification of any circuit should beattempted.Service work should be performed only afteryou are thoroughly familiar with all of thefollowing safety checks and servicingguidelines.
SAFETY CHECKCare should be taken while servicing this color monitorbecause of the high voltage used in the deflection circuits.These voltages are exposed in such areas as theassociated flyback and yoke circuits.
FIRE & SHOCK HAZARDAn isolation transformer must be inserted between the
color monitor and AC power line before servicing thechassis.
• In servicing, attention must be paid to the original leaddress specially in the high voltage circuit. If a shortcircuit is found, replace all parts which have beenoverheated as a result of the short circuit.
• All the protective devices must be reinstalled per theoriginal design.
• Soldering must be inspected for the cold solder joints,frayed leads, damaged insulation, solder splashes, orthe sharp points. Be sure to remove all foreignmaterials.
IMPLOSION PROTECTIONAll used display tubes are equipped with an integralimplosion protection system, but care should be taken toavoid damage and scratching during installation. Use onlysame type display tubes.
X-RADIATIONThe only potential source of X-radiation is the picture tube.However, when the high voltage circuitry is operatingproperly there is no possibility of an X-radiation problem.The basic precaution which must be exercised is keep thehigh voltage at the factory recommended level; the normalhigh voltage is about 25.5kV. The following steps describehow to measure the high voltage and how to prevent X-radiation.
Note : It is important to use an accurate high voltage meter calibrated periodically.
• To measure the high voltage, use a high impedance high voltage meter, connect (–) to chassis and (+) tothe CDT anode cap.
• Set the brightness control to maximum point at fullwhite pattern.
• Measure the high voltage. The high voltage metershould be indicated at the factory recommended level.
• If the meter indication exceeds the maximum level,immediate service is required to prevent the possibilityof premature component failure.
• To prevent X-radiation possibility, it is essential to usethe specified picture tube.
CAUTION:Please use only a plastic screwdriver to protect yourselffrom shock hazard during service operation.
SAFETY PRECAUTIONS
- 3 -
TIMING CHART
- 4 -
VIDEO
SYNC
C E
DF
AB
H – 37.500 26.667 20.317 6.349 2.032 3.810 0.508
V – 75.000 13.333 12.800 0.533 0.080 0.427 0.027
H – 31.469 31.778 25.422 6.356 3.813 1.907 0.636
V – 59.940 16.683 15.253 1.430 0.064 1.048 0.318
H – 43.269 23.112 17.778 5.334 1.556 2.222 1.556
V – 85.008 11.764 11.093 0.671 0.069 0.579 0.023
H – 31.470 31.778 25.422 6.356 3.813 1.907 0.636
V + 70.080 14.269 12.711 1.558 0.064 1.080 0.414
H + 46.880 21.330 16.160 5.170 1.620 3.230 0.320
V + 75.010 13.331 12.798 0.533 0.064 0.448 0.021
H + 53.674 18.631 14.222 4.409 1.138 2.702 0.569
V + 85.061 11.756 11.178 0.578 0.056 0.503 0.019
H + 60.023 16.660 13.003 3.657 1.219 2.235 0.203
V + 75.029 13.328 12.795 0.533 0.050 0.466 0.017
H + 68.677 14.561 10.836 3.725 1.061 2.201 0.508
V + 84.997 11.765 11.183 0.582 0.044 0.523 0.015
H + 63.98 15.63 11.85 3.78 1.04 2.30 0.44
V + 60.02 16.661 16.005 0.656 0.047 0.594 0.015
Mode H/VSort
1
2
3
4
5
6
7
8
9
<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >>
SyncPolarity Frequency
Total Period(E)
Video Active Time (A)
Sync Duration(D)
Blanking Time(B)
Back Porch(F)
Front Porch(C)
640x48075Hz
640x48085Hz
720x40070Hz
800x60075Hz
800x60085Hz
1024x76875Hz
1024x76885Hz
1280x102460Hz
640x48060Hz
Resolution
- 5 -
OPERATING INSTRUCTIONS
ColorealTM
FRONT VIEW REAR VIEW
AC Power Socket Signal ConnectorSee Front Control Panel
Front Control Panel
1. Power/LEDControls power to the monitor.The LED on the power button is illuminated when the power is on.
2. Right AdjustmentMoves clockwise through menu options or increasesadjustment levels.
3. Left AdjustmentMoves counter-clockwise through menu options ordecreases adjustment levels.
4. SelectLaunches on-screen displays, selects functions andadjustments, and exits menus and On-Screen Display.
5. Hot Key
Left AdjustmentJust select left adjustment key without OSD display.Contrast menu display.
Right adjuatment Just select right adjustment key with OSD display.Brightness menu display.
Power ON/OFF Button
234 1
ColorealTM
WIRING DIAGRAM
- 6 -
P501
P201
P405
P301P302
P303
P702
P701
T1
P402
P902
S+
S
Signal Cable
AC Socket
FB
T
BLOCK DIAGRAM
- 7 -
ME
NU
PO
WE
R
PO
WE
R IN
PU
T10
0~24
0VA
C(5
0/60
Hz)
Line
Filt
er
Deg
auss
ing
Circ
uit
< O
SD
Con
trol
>
SM
PS
TR
AN
S(T
901)
SM
PS
CO
NT
RO
L(I
C90
1)
DP
MC
ON
TR
OL
CIR
CU
IT
Vol
tage
Reg
ulat
ing
Circ
uit
80V
50V
15V
6.3V
TIL
TC
ontr
olC
ircui
t
6.3V
15V
E2 P
RO
M(I
C40
2)
H P
OS
ITIO
NB
RIG
HT
NE
SS
CO
NT
RA
ST
H S
IZE
V P
OS
ITIO
NV
SIZ
ES
PC
CT
RA
PE
ZO
IDP
IN B
ALA
NC
EP
AR
ALL
ELO
GR
AM
RO
TA
TIO
N
DE
GA
US
SC
OLO
R T
EM
PE
RA
DU
RE
FA
CT
OR
Y R
EC
ALL
EX
IT
5V
OS
D IC
(IC
301)
NT
6872
H-S
ync
Sig
V-S
ync
Sig
I2C
DA
TA
(SD
A)
I2C
CLO
CK
(SC
L)
VID
EO
LM12
69
PR
E-A
MP
(IC
302)
Sig
nal
Cab
leR G B
VID
EO
LM24
67
LM24
80
CU
T O
FF
IC
(IC
304)
MA
IN A
MP
(IC
303)
5V
5V
H/V
Syn
c P
roce
ssor
( IC
701
)T
DA
4857
V-O
UT
( IC
601)
TD
A48
66
H-O
UT
( Q
706)
H-L
inea
rity
Cor
rect
ion
DC
/DC
Con
vert
er
X-R
AY
Pro
tect
ion
Circ
uit
FB
T(
T70
1 )
Dyn
amic
Foc
usC
ircui
t
Aut
oB
eam
Lim
it
Ver
tical
Bla
nkin
g,B
right
ness
Con
trol
- 16
0V
40V
400V
ST
EP
UP
15V
D/D
Fee
d B
ack
15V
MIC
OM
(IC
401)
SC
L / S
DA
H/V
Syn
c,P
WM
Con
trol
15V
5V15
V
80V
15V
50V
DY
CD
T
Hea
ter
( 6.
3V )
I2C
I2C
I2C
H/V
Syn
c
G1Screen(G2)
Dynamic FocusStatic Focus
H.V
R/G
/BD
rive/
Con
tras
tC
ut-O
ff
H-D
RV
B-D
RV
B+
15V
TILT COIL
DEGAUSSINGCOIL
I2C
Vou
t 1
Vou
t 2
+ColorealTM
DESCRIPTION OF BLOCK DIAGRAM
- 8 -
1. Line Filter & Associated Circuit.This is used for suppressing noise of power input lineflowing into the monitor and/or some noise generated inthis monitor flowing out through the power input line.That is to say, this circuit prevents interference betweenthe monitor and other electric appliances.
2. Degauss Circuit & Coil.The degauss circuit consists of the degaussing coil, thePTC(Positive Temperature Coefficient) thermistor(TH901),and the relay(RL901). This circuit eliminates abnormalcolor of the screen automatically by degaussing theshadow mask in the CRT during turning on the powerswitch. When you need to degauss in using the monitor,select DEGAUSS on the OSD menu.
3. SMPS(Switching Mode Power Supply).This circuit is working of 90~264V AC(50/60Hz).The operation procedure is as follows:1) AC input voltage is rectified and smoothed by the bridgediodes (D900) and the capacitor (C908).2) The rectified voltage(DC) is applied to the primary coilof the transformer(T901).3) The control IC(IC901) generates switching pulse to turnon and off the primary coil of the transformer (T901)repeatedly.4) Depending on turn ratio of the transformer, thesecondary voltages appear at the secondary coils of thetransformer(T901).5) These secondary voltages are rectified by eachdiode(D941, D942, D951, D961, D962, D971) and operateother circuit. (horizontal and vertical deflection, videoamplifier, ...etc.)
4. Display Power Management Circuit.This circuit control power consumption of the monitor bydetecting H and V sync signal. There are off mode. When nohorizontal or vertical sync signal input, the circuit consists ofQ941 and Q951 becomes off mode. It’s power consumptionis below 5W.
5. X-ray Protection.If the high voltage of the FBT reaches up to 29kV (abnormalstate), IC401(MICOM) pin 35 Sensing from FBT directly.Then MICOM control IC701 (Deflection controller) to stopHorizontal drive pulse and stop Horizontal Deflection.
6. Micom(Microprocessor) Circuit.The operating procedure of Micom(Microprocessor) andits associated circuit is as follows:
1) H and V sync signal is supplied from the signal cable.2) The Micom(IC401) distinguishes polarity and
frequency of H and V sync.
3) The Micom sets operating mode and offers thecontrolled data. (H-size, H-position, V-size, ... etc.)
4) The controlled data of each mode is stored in itself.5) User can adjust screen condition by each OSD
function. The data of the adjusted condition is storedin EEPROM(IC402).
7. Horizontal and Vertical Synchronous Processor.This circuit generates the horizontal drive pulse and thevertical drive pulse by taking sync-signal from the Signal-Cable. This circuit consists of the TDA4857(IC701) andthe associated circuit.
8. D/D(DC to DC) Converter.This circuit supplies DC voltage to the horizontal deflectionoutput circuit by increasing DC 50V which is thesecondary voltage of the SMPS in accordance with theinput horizontal sync signal.
9. Side-Pincushion & Trapezoid Correction Cirucit.This circuit improves the side-pincushion and thetrapezoid distortion of the screen by mixing parabola andsaw-tooth wave to output of the horizontal deflection D/Dconverter which is used for the supply voltage(B + ) of thedeflection circuit.
10. Horizontal Deflection Output Circuit.This circuit makes the horizontal deflection by supplyingthe saw-tooth current to the horizontal deflection yoke.
11. High Voltage Output & FBT(Flyback Transformer).The high voltage output circuit is used for generating pulsewave to the primary coil of the FBT(Flyback Transformer) .A boosted voltage(about 25.5KV) appears at thesecondary of the FBT and it is supplied to the anode of theCDT. And there are another output voltages such as thedynamic focus and the screen voltage(G2).
12. H-Linearity Correction Circuit.This circuit corrects the horizontal linearity for eachhorizontal sync frequency.
13. Vertical Output Circuit.This circuit takes the vertical ramp wave from theTDA4857(IC701) and performs the vertical deflection bysupplying the saw-tooth current from the TDA4866(IC601)to the vertical deflection yoke.
14. Dynamic Focus Output Circuit.This circuit takes the horizontal and the vertical parabolawaves from the TDA4857(IC701) and amplifies it tomaintain constant focus on center and corners in thescreen.
- 9 -
15. H& V Blanking and Brightness Control.Blanking circuit eliminates retrace line by supplyingnegative pulse to the G1 of the CRT. And Brightnesscircuit is used for control of the screen brightness.
16. Image Rotation (Tilt) Circuit.This circuit corrects the tilt of the screen by supplying theimage rotation signal to the tilt coil which is attached nearthe deflection yoke of the CRT.
17. OSD CircuitThis circuit is used for performing the OSD(On-Screen-Display) function.When a user selects the OSD Select/Adjustment control,the adjustment status displays on the screen.
18. Video Pre-Amp Circuit.This circuit amplifies the analog video signal from 0-0.7Vto 0-4V. It is operated by taking the clamp, R, G, B driveand contrast signal from the Micom(IC401).
19. Video Output Amp Circuit.This circuit amplifies the video signal which comes fromthe video pre-amp circuit and amplified it to applied theCRT cathode.
- 10 -
ADJUSTMENT
GENERAL INFORMATION
All adjustment are thoroughly checked and correctedwhen the monitor leaves the factory, but sometimesseveral adjustments may be required. Adjustment should be following procedure and afterwarming up for a minimum of 30 minutes.
• Alignment appliances and tools.- IBM compatible PC.- Programmable Signal Generator.
(eg. VG-819 made by Astrodesign Co.)- EPROM or EEPROM with saved each mode data.- Alignment Adaptor and Software.- Digital Voltmeter.- White Balance Meter.- Luminance Meter.- High-voltage Meter.
AUTOMATIC AND MANUAL DEGAUSSINGThe degaussing coil is mounted around the CDT so thatautomatic degaussing when turn on the monitor. But amonitor is moved or faced in a different direction, becomepoor color purity cause of CDT magnetized, then pressDEGAUSS on the OSD menu.
ADJUSTMENT PROCEDURE & METHOD- Install the cable for adjustment such as Figure 1and run
the alignment program on the DOS for IBM compatible PC. - Set external Brightness and Contrast volume to max position.
1. Adjustment for B+ Voltage.1) Display cross hatch pattern at Mode 8.2) Check C999 (+) voltage to 50± 0.5Vdc.
2. Adjustment for High-Voltage. 1) Display cross hatch pattern at Mode 8.2) DIST.ADJ→CTRL PWM → High Voltage Command.3) Adjust High Voltage to 25.5kV±0.3 kVdc.4) Press Enter Key.
3. Adjustment for Factory Mode (Preset Mode).1) Display cross hatch pattern at Mode 1.2) Run alignment program for CQ771G on the IBM
compatible PC.3) EEPROM → ALL CLEAR → Y(Yes) command.
<Caution> Do not run this procedure unless the EEPROM is changed. All data in EEPROM (mode data and color data) will be erased.
4) Power button of the monitor turn off → turn on.5) COMMAND→PRESET START→Y(Yes) command.6) DIST. ADJ. → CTRL PWM → TILT command.
7) Adjust tilt as arrow keys to be the best condition.8) DIST. ADJ. → BALANCE command.9) Adjust parallelogram as arrow keys to be the best
condition. 10) Adjust balance of pin-balance as arrow keys to be
the best condition.11) DIST. ADJ. → FOS. ADJ command.12) Adjust V-SIZE as arrow keys to 234±2mm.13) Adjust V-POSITION as arrow keys to center of the
screen.14) Adjust H-SIZE as arrow keys to 312±2mm.15) Adjust H-POSITION as arrow keys to center of the
screen.16) Adjust S-PCC (Side-Pincushion) as arrow keys to be
the best condition.17) Adjust TRAPEZOID as arrow keys to be the best
condition.18) Save of the Mode 1.19) Display from Mode 1 to 8 and repeat above from
number 12) to 19)20) PRESET EXIT → Y (Yes) command.
4. Adjustment for White Balance and Luminance.1) Set the White Balance Meter.2) Press the DEGAUSS on the OSD menu for
demagnetization of the CDT.3) COLOR ADJ. → LUMINANCE command of the
alignment program.4) Set Brightness and Contrast to Max position.5) Display color 0,0 pattern at Mode 8.6) COLOR ADJ.→ BIAS ADJ.→ COLOR No. → 1
command of the alignment program.7) Check whether green color or not at R-BIAS and G-
BIAS to min position and B-BIAS to 127(7F) andSub-Brightness to 177(B1) position. Adjust G2(screen) command to 0.4± 0.05FL of the rasterluminance.
8) Adjust R-BIAS and G-BIAS command to x=0.283±0.005 and y=0.298±0.005 on the White BalanceMeter with PC arrow keys.
9) Adjust SUB-Brightness command to 0.5±0.1FL of theraster luminance.
10) Adjust repeat number 8).11) After push the “ENTER” key.
11-1) COMMAND → PRESET START → Y(Yes) command.12) Display color 15,0 full white pattern at Mode 8.13) DRIVE ADJ.→ No 1. command.
- 11 -
14) Set Brightness is cut-off(0.06FL) and Contrast toMax position.
15) Set SUB-CONTRAST Max 127(7F) (decimal) position.16) Set B-DRIVE to 90(5A); LG CDT at DRIVE of the
alignment program. (TECO CDT: B-DRIVE 100(64))17-1) Adjust R-DRIVE and G-DRIVE command to white
balance x=0.283±0.003 and y=0.298±0.003 at Full-White on the White Balance Meter with PC arrow keys.
17-2) Display color 15,0 window pattern 5Box 50x50mm atmode 8.
18) Adjust SUB-CONTRAST command to 50±1FL atB/Raster 0.06FL.
19) Display color 15,0 full white patten at Mode 8.20) Set Brightness and Contrast to Max position.21) COLOR ADJ. → LUMINANCE → ABL command.22) Adjust ABL to 33±1FL of the luminance at B/Raster 0.06FL.23) After push the “ENTER” key, and “COMMAND →
PRESET EXIT → Y(Yes)” command.24) Exit from the program.
5. Input EDID Data.1) Display color 15,0 cross hatch pattern at Mode 8.2) EEPROM → Write EDID command and confirm
“EDID Write OK!!” message of monitor.3) Exit from the alignment program.4) Power switch OFF/ON for EDID data save.
6. Adjustment for Focus.1) Set the Brightness and Contrast to max position.2) Display cross hatch with quadrant text pattern in full
screen at Mode 8.3) Adjust two Focus control on the FBT that focus
should be the best condition.
- 12 -
TROUBLESHOOTING GUIDE
1. NO POWER
NO POWER(POWER INDICATOR OFF)
TROUBLE IND900
TROUBLE IN FUSE(F901)
TROUBLE IN IC901
TROUBLE IN D941, D942, D951, D961, D962, D971
TROUBLE IN
Q903, Q952,
Q951, Q942, Q941
CHECKFUSE OK?
CHECKC908 VOLTAGE?
(AC120V: 160VDC,AC220V: 304VDC)
NO
YES
YES
YES
YES
NO
NO
NO
CHECKIC901 PIN 6WAVEFORM
(SQUARE WAVE COMES OUT?)
CHECKD941, D942, D951, D961,
D962, D971VOLTAGE?
- 13 -
2. NO CHARACTER
NO CHARACTER
CHECKIC302
PIN 9(5V) ?
CHECK IC302 PIN 5, 6, 7?
CHECK IC302 PIN 20, 19, 18 ?
CHECKIC303
PIN 1, 2, 3 ?
CHECK IC303 PIN 4 (80V)
PIN 8 (12V) ?
TROUBLE IN P302 5V LINE
TROUBLE IN PC SIGNAL,P301 SIGNAL CABLE
TROUBLE IN IC302
TROUBLE IN P303 12V LINE/80V LINE
TROUBLE IN IC303
NO
YES
NO
NO
YES
YES
YES
YES
NO
NO
CHECK R, G, B CATHODE
VOLTAGE?
TROUBLE IN R341~R343,R331~R333, L311~L313,D307~D312
Model Name:S7500 (PE1165T), S7500 (PE1165),CV7500 (PE1165U)
Model Name:MV7500 (PE1165U),MV7500 (PE1165)
IIC-SDAIIC-SCLDDC-SDADDC-SCL
- 32 - - 33 -
SCHEMATIC DIAGRAM
NOTICESince this is a basic schematic diagram.The value of components and some partial connection are sucject to be changed for improvement without notice.
- 34 - - 35 -
PRINTED CIRCUIT BOARD
3. MAIN BOARD (Component Side) 4. MAIN BOARD (Solder Side)
1. CONTROL BOARD (Component Side) 2. CONTROL BOARD (Solder Side)