Collet Chucks & Collet Pads
Selection Chart For Thru-Hole Collet Chucks:
Hot Rolled Stock vs. Ground or Cold Rolled StockIf you contemplate using hot rolled bar stock then the "Hot Rolled" branch should be selected.Drawtube Pull Required vs. Drawtube Push AcceptableSome servo barfeeders require the drawtube to pull when closing the collet chuck. If no barfeeder is involved or the selected barfeeder does not have this requirement, then a collet chuck which closes when the drawtube is pushed forward would be acceptable.Dead Length Required vs. "Pull Back Action"A collet chuck with "Pull Back Action" will pull the bar away from the stop in the turret. If inconsistent stock length on a facing cut is unacceptable, or if the barfeed is servo driven, then a dead length collet chuck is indicated.
Superior Cincinnati is an industry leader in the design and manufacturing of Collet Chucks, Collet Pads, Feed Finger Pads and workholding accessories. Since 1975 we have provided outstanding quality, value and service to our customers. We continuously strive to meet our customers ever increasing requirements to improve productivity and profits. Superior Cincinnati workholding products come with off-the-shelf delivery for most machine tools. Our national network of distributors, located in all major cities, are ready to serve your workholding needs. Our products are manufactured to the highest quality standards each and every day, priced to save you money and fully guaranteed to your satisfaction.
Precision Required vs. Standard AccuracySelect "Precision Required" where close repeatability is required a distance from the face of the collet chuck.Solid Collet vs. Master Collet with Collet PadsSome collet chucks require the use of a solid collet such as 5C, 16C, 3J or "B" Style collets. This means that the solid collet must be changed to accommodate different diameters. With a master and pads, the master collet remains in the collet chuck and only the collet pads are changed. Solid collets are considered more accurate but cost about 50% more than collet pads of comparable size."S" Style vs. Turret Lathe PadsSome customers prefer one type of collet pad over the other. Turret Lathe Pads are more readily available from several manufacturers. "S" Style Pads are only available from a limited number of suppliers.
2. © Superior Cincinnati, 2004, 2010
Thru-Hole Collet Chuck Index
• No part movement• True parallel grip = More gripping force• Drawtube push to actuate• Up to 6" bar stock capacity• Full .125" clamping range permitting optional robot load
• Exclusive Centr-Adjust feature to centralize the chuck• Repeatability @ chuck face is .0005" T.I.R. or better• Uses "S" Style or Turret Lathe Collet Pads• Has provision for an internal workstop• Short length• In stock
• Close repeatability a distance from the face of the chuck• Extended grip length-Able to grip on two diameters• Drawtube push to actuate• Up to 2" bar stock capacity• Full .063" clamping range
• Exclusive Centr-Adjust feature to centralize the chuck• Repeatability @ chuck face is .0005" T.I.R. or better• Uses Turret Lathe Collet Pads• Helps prevent vibration due to bar whip• In stock
• Repeatability @ chuck face is .0005" T.I.R. or better• Uses 5C, 16C or 3J Style Collets• Features a collet locating pin• In stock
• Repeatability @ chuck face is .0005" T.I.R. or better• Uses "S" Style, Martin Type or Turret Lathe Collet Pads• Master collet provided• Ideal for first operations and slug work• In stock
• No part movement• Ideal for subspindle applications, secondary operations and part transfers• Available with optional part ejector• Drawtube push to actuate• Up to 2 3/8" bar stock capacity
• Exclusive Centr-Adjust feature to centralize the chuck• Repeatability @ chuck face is .0005" T.I.R. or better• Uses "B" Style Solid Collets• Features a collet locating pin• Small size allows for greater tool clearances and more z-axis travel• In stock
• Pullback action• Drawtube actuated• Up to 1 3/4" bar stock capacity• Exclusive Centr-Adjust feature to centralize the chuck
• Pullback action• Drawtube actuated• Up to 4" bar stock capacity• Exclusive Centr-Adjust feature to centralize the chuck
• No part movement• True parallel grip = More gripping force• Drawtube pull to actuate• Up to 6" bar stock capacity• Full .125" clamping range permitting optional robot load
• Exclusive Centr-Adjust feature to centralize the chuck• Repeatability @ chuck face .is 0005" T.I.R. or better• Uses "S" Style or Turret Lathe Collet Pads• Has provision for an internal workstop• Short length• Need for turret stop is lessened or eliminated
3.
CDS "S" Style Conventional Master Collet Chucks Page 5
COLLET CHUCKS PADS Page 16
ORDERING INFORMATION Page 19
CNS/CNT "S" Style & Turret Lathe Collet Chucks Page 4
CDD Duplex Collet Chucks Page 5
CPD "B" Style Solid Collet Chucks Page 5
CDC 5C, 16C, 3J Conventional Solid Collet Chucks Page 5
CRS/CRT "S" Style & Turret Lathe Collet Chucks for Servo Barfeeders Page 4
Note: Dimensional data and capacities are shown in inches. Specifications and dimensional data are subject to change with design improvements. All pads available soft or hardened to 58-60 Rc.Specials: We make collet chucks and pads to fit your application.
• No part movement• True parallel grip = More gripping force = Faster feeds and speeds• Large .125" clamping range (opens & closes 0.6" from nominal) = Ability of the chuck to handle hot rolled stock• Exclusive Centr-Adjust feature to centralize the chuck• Short, totally sealed design – No exposed mating surfaces• Chuck is shorter than other competitive models
CNS/CNT "S" Style & Turret Lathe Collet Chucks
CRS/CRT "S" Style & Turret Lathe Collet Chucks for Servo Barfeeders
FOR TURRET LATHE COLLET PADS
1027
1025
1026
1022
1049
1014
CNT-15
CNT-20
CNT-25
CNT-30
CNT-45
CNT-60
1.50
2.00
2.50
3.00
4.50
6.00
A05A06A08
1.31
1.75
2.18
2.62
3.87
5.00
1.38
1.75
2.12
3.18
4.25
6.50
6.50
8.25
10.00
13.00
4.304.474.66
A05A06A08
5.215.285.64
A05A06A08
5.215.285.64
A05A06A08
5.215.285.49
A06A08A11
5.966.176.40
A11A15
7.908.31
1.06 5.25
COLLETNUMBER
CHUCKNOSE
DIAMETER
SPINDLENOSE
OVERALLLENGTH
CHUCKMODEL
NUMBER
MAXIMUM BAR CAPACITY
ROUND HEXAGON SQUARE
FOR TURRET LATHE COLLET PADS
1027
1025
1026
1022
1049
1014
CRT-15
CRT-20
CRT-25
CRT-30
CRT-45
CRT-60
1.50
2.00
2.50
3.00
4.50
6.00
A05A06A08
1.31
1.75
2.18
2.62
3.87
5.00
1.38
1.75
2.12
3.18
4.25
6.50
8.25
10.00
12.00
15.00
5.085.155.51
A05A06A08
5.085.155.51
A05A06A08
5.335.405.61
A05A06A08
5.335.405.84
A06A08A11
5.906.116.31
A11A15
6.817.32
1.06 6.50
COLLETNUMBER
CHUCKNOSE
DIAMETER
SPINDLENOSE
OVERALLLENGTH
CHUCKMODEL
NUMBER
MAXIMUM BAR CAPACITY
ROUND HEXAGON SQUARE
FOR "S" STYLE COLLET PADS
1216
1222
1226
1230
1240
CNS-16
CNS-22
CNS-26
CNS-30
CNS-40
1.62
2.25
2.62
3.00
4.00
A05A06A08
1.41
1.94
2.25
2.59
3.43
1.56
1.84
2.09
2.81
6.50
8.25
8.25
10.00
4.304.474.66
A05A06A08
5.215.285.64
A05A06A08
5.215.285.64
A05A06A08
5.215.285.49
A06A08A11
5.966.176.40
1.16 5.25
COLLETNUMBER
CHUCKNOSE
DIAMETER
SPINDLENOSE
OVERALLLENGTH
CHUCKMODEL
NUMBER
MAXIMUM BAR CAPACITY
ROUND HEXAGON SQUARE
FOR S STYLE COLLET PADS
1216
1222
1226
1230
1240
CRS-16
CRS-22
CRS-26
CRS-30
CRS-40
1.62
2.25
2.62
3.00
4.00
A05A06A08
1.41
1.94
2.25
2.59
3.43
1.56
1.84
2.09
2.81
6.50
8.25
10.00
12.00
5.085.155.51
A05A06A08
5.085.155.51
A05A06A08
5.335.405.61
A05A06A08
5.335.405.84
A06A08A11
5.405.615.81
1.16 6.50
COLLETNUMBER
CHUCKNOSE
DIAMETER
SPINDLENOSE
OVERALLLENGTH
CHUCKMODEL
NUMBER
MAXIMUM BAR CAPACITY
ROUND HEXAGON SQUARE
Benefits• No part movement• Designed for Servo Barfeeders• True parallel grip = More gripping force = Faster feeds and speeds• Large .125" clamping range (opens & closes 0.6" from nominal) = ability of the chuck to handle hot rolled stock• Exclusive Centr-Adjust feature to centralize the chuck• Short, totally sealed design – No exposed mating surfaces• Chuck is shorter than other competitive models
Benefits
4.
1220CNS-20 2.00 1.75 1.38 6.50A05A06A08
5.215.285.64
CPD "B" Style Solid Collet Chucks CDD Duplex Collet Chucks
FOR "B" STYLE COLLET PADS
B-30
B-42
B-60
CPD-30
CPD-42
CPD-60
1.18
1.65
2.36
A05A06A08
1.02
1.42
2.04
1.16
1.67
3.50
4.38
4.644.815.00
A05A06A08
5.775.846.20
A05A06A08
5.966.036.39
0.83 3.25
COLLETNUMBER
CHUCKNOSE
DIAMETER
SPINDLENOSE
OVERALLLENGTH
CHUCKMODEL
NUMBER
MAXIMUM BAR CAPACITY
ROUND HEXAGON SQUARE
FOR TURRET LATHE COLLET PADS
1071
1025
CDD-15
CDD-20
1.50
2.00
A05A06A08
1.31
1.75 1.38 5.00
7.087.257.44
A05A06A08
7.457.517.88
1.06 4.00
COLLETNUMBER
CHUCKNOSE
DIAMETER
SPINDLENOSE
OVERALLLENGTH
CHUCKMODEL
NUMBER
MAXIMUM BAR CAPACITY
ROUND HEXAGON SQUARE
FOR 5C, 16C OR 3J COLLET PADS
5C
16C
CDC-5C
CDC-16C
1.06
1.62
A05A06A08
0.90
1.41 1.14 3.38
3.934.194.27
A05A06A08
4.714.885.07
3JCDC-3J 1.75 1.53 1.25 3.63A05A06A08
4.464.634.82
0.75 2.75
COLLETNUMBER
CHUCKNOSE
DIAMETER
SPINDLENOSE
OVERALLLENGTH
CHUCKMODEL
NUMBER
MAXIMUM BAR CAPACITY
ROUND HEXAGON SQUARE
CDC 5C, 16C, 3J Conventional Solid Collet Chucks
FOR "S" STYLE COLLET PADS
1216
1222
CDS-16
CDS-22
1.62
2.25
A05A06A08
1.41
1.94 1.56 4.86
7.737.908.09
A05A06A08
7.587.658.01
1226CDS-26 2.62 2.25 1.84 5.25A05A06A08
7.988.058.41
1230CDS-30 3.00 2.59 2.09 6.00A05A06
A08
8.238.30
8.51
1240CDS-40 4.00 3.43 2.81 7.75A06A08A11
9.289.729.72
1.16 4.00
COLLETNUMBER
CHUCKNOSE
DIAMETER
SPINDLENOSE
OVERALLLENGTH
CHUCKMODEL
NUMBER
MAXIMUM BAR CAPACITY
ROUND HEXAGON SQUARE
CDS "S" Style Conventional Master Collet Chucks
• Extended grip length – Able to grip on two diameters• Exclusive Centr-Adjust feature to centralize the chuck• Sealed design – No exposed mating surfaces• Helps prevent vibration due to bar whip
Benefits• No part movement• Ideal for subspindle applications, secondary operations and part transfers• Available with optional part ejector• Small size allows for greater tool clearances and more z-axis travel
Benefits
5.
B-90CPD-90 3.13 2.72 2.20 6.00A06A08A11
7.087.267.52
All chucks on pages 4 & 5 include Spindle Adapter, Drawtube Adapter, Mounting Bolts & Maintenance Instructions.
Customer ServiceUSA: (800) 875-8175
Phone: (513) 272-1122Fax: (513) 272-0503
SUPER-GRIP® DISTINCTIVE BIDIRECTIONAL SERRATION DESIGN
EMERGENCY COLLET PADS (Soft, Blank)
• Specifically designed for emergencies• Available in "S", Turret Lathe and Martin Type styles• Collet pad material is soft with a 5/16" pilot hole for quick drilling, boring or stepping• Can be used multiple times by boring out to a larger size• May be hardened to improve wear qualities after boring• Easy steps to speedy productivity 1. Install pad into master collet or collet pad top jaws 2. Insert pins to hold the pad in the closed position 3. Drill and finish bore, or step to the desired size 4. Remove the pins
SHAPES AND SPECIALS
PADS FOR TOP JAWS
• Pads for master collets and feeder pads are available from stock in round hexagon and square shapes. Unique shapes, eccentric, rectangles, octagons or off-center holes can be custom made• Collet and feeder pads are available in a variety of materials including high quality alloy steel, bronze and other phenolics • Most pads are hardened for maximum resilience • All collets are manufactured for maximum concentricity
• Concentricity of round, smooth pads is .002" T.I.R. or better at the face
Tighter tolerances are possible upon request.
• Lower tooling cost - Collet Pads are less expensive than boring out top jaws• Top jaws do not have to be machined in order to grip standard shapes• Reduce set-up time - Collet Pads are changed much faster than chuck jaws and facilitate set-up for a variety of sizes• Minimize scrap - Positive holding action grips workpiece firmly in position, reducing scrap loss• Increase tool flexibility - Collet Pads can be used economically for both bar and chucking work. They are offered for chuck sizes 8 inches through 18 inches and for all standard makes of chucks• Reduce storage space - Collet Pads are much smaller than jaws and require less storage space
• Specifically designed for NC/CNC turning centers• Superior's Super-Grip® bidirectional collet pads feature serration lands which penetrate the work for a positive gripping action (better than competing pads)• Unique and exclusive pyramid configuration provides equal gripping force along spindle axis in both forward and reverse spindle rotation• Assures smooth bar feeding while precluding "push back" from cutting forces• Ideally suited for exotic or hard materials such as iconel, stainless...and many others• Square, hexagon and octagon pads are furnished with annular serrations
Super-Grip® is a registered trademark of Superior Cincinnati
COLLET PAD FEATURES AND BENEFITS
6.
• Dovetail feature machined in the middle diameter of each segment• Clamp screw engages the dovetail feature to secure the pad segment(s) into the master collet• Used primarily on multi-spindle automatics and in some Collet Chucks• Designed to be changed without requiring the removal of the master collet from the chuck• Machinable Emergency Collet Pads available from stock• "S" Style Pads can be purchased in a variety of shapes, sizes and materials• Wrenches and clamps are sold separately (see page 11)
• Available for popular jaw chucks• Used in jaw chucks with collet pad top jaws• For chucks that have master jaws that accept standard Turret Lathe Collet Pads• Increases flexibility of jaw chucks by eliminating wasted time spent on jaw change over• Offered in distinctive bidirectional serrated design to accommodate various stock diameters within working range of the chuck• Machinable Emergency Collet Pads available from stock• Jaw Chuck Pads can be purchased in a variety of shapes, sizes and materials
• Identified by square lugs threaded into the periphery of the ground diameter closest to the face of the master collet• By turning the set screws, the lugs expand into slots thus securing the pad to the master collet• Master collet allows changing of the pad(s) without removing the master from the spindle• Pads are primarily used on multi-spindle automatics but are used in some Collet Chucks• Machinable Emergency Collet Pads available from stock• Martin Type Pads can be purchased in a variety of shapes, sizes and materials• Lugs can be purchased separately (see page 13)
• Seated in the recess within the master feeder• One pad has a slot for engaging a key of the master feeder to eliminate pad rotation• For maximum wear the Feed Finger Pads are hardened• Pads are quickly and easily changed• Feed Finger Pads can be purchased in a variety of shapes, sizes and materials
• Threaded holes in the periphery of the middle diameter are used to secure the pads to the master collet or top jaws• These pads were originally used on turret lathes, thus their name• Turret Lathe Pads are commonly used with Collet Chucks and collet pad top jaws• Machinable Emergency Collet Pads available from stock• Turret Lathe Pads can be purchased in a variety of shapes, sizes and materials• Mounting screws are sold separately (see page 9)
• Manufactured for use in all Superior Cincinnati Collet Chucks• Also available for many other manufacturer's Collet Chucks• Designed for bar and chucking work, available from stock with up to 6" chuck capacity• Machinable Emergency Collet Pads available from stock• Collet Chuck Pads can be purchased in a variety of shapes, sizes and materials
Collet Pad Index
7.
JAW CHUCK PADS Page 14
FEED FINGER PADS (MODEL "A") Page 12
MARTIN TYPE PADS Page 12
"S" STYLE PADS Page 10
TURRET LATHE PADS Page 8
CUSTOM QUOTE REFERENCE GUIDE AND ORDERING INFORMATION Pages 18- 19
COLLET CHUCK PADS Page 16
GISHOLT
# 3 1 1/2 1 1/2 1 3/8 1 1/8 1060(4 Split)3Y-7112-A
3X-7731 Rd.3X-7735 Hx.3X-7733 Sq.
# 3, 4 2 2 1 3/4 1 3/8 1061(4 Split)4Y-7112-A
4X-7731 Rd.4X-7735 Hx.4X-7733 Sq.
# 55-AR 1-L
2 1/2 2 1/2 2 1/8 1 3/4 1063(4 Split)5Y-7112
5X-7731 Rd.5X-7735 Hx.5X-7733 Sq.
# 55-AR 1-L
2 1/2 2 1/2 2 1/8 1 3/4 1026(3 Split)11X-6762
11X-7737 Rd.11X-7741 Hx.11X-7739 Sq.
# 5 5 ABC 3 3 2 5/8 2 1/8 1022
(3 Split)5X-78495X-7843 Rd.5X-7847 Hx.5X-7845 Sq.
1-L2-L 3 1/2 3 1/2 3 2 7/16 1066
(4 Split)12X-6561
2-L-06002-B
12X-7731 Rd.12X-7735 Hx.12X-7733 Sq.
1-L2-L 3 1/2 3 1/2 3 2 7/16 1067
(3 Split)12X-676212X-7737 Rd.12X-7741 Hx.12X-7739 Sq.
# 5, 5-AR2-L, 3-L 4 1/2 4 1/2 3 7/8 3 1/8 1023
(4 Split)13X-65613-L-6561
13X-7731 Rd.13X-7735 Hx.13X-7733 Sq.
# 5, 5-AR2-L, 3-L 4 1/2 4 1/2 3 7/8 3 1/8 1068
(3 Split)13X-6561-B13X-7716 Rd.13X-7720 Hx.13X-7718 Sq.
# 3, 4 2 2 1 3/4 1 3/8 1025(3 Split)
4Y-7138-A4Y-7138-B
4X-7731-A Rd.4X-7735-A Hx.4X-7733-A Sq.
BARDONS & OLIVER#3, 5
#7#10
1 1/22
3 1/16
1 1/22
3 1/16
1 19/641 23/32
2 5/8
1 3/641 13/322 5/32
109610971091
MACHINESIZE
MACHINEMODEL
SUPERIORNUMBER
MASTER COLLETNUMBER
MASTER PADNUMBERROUND HEXAGON SQUARE
COLLET PAD CAPACITY
JONES & LAMSON
# 3 Universal 1 1/2 1 1/2 1 1/4 1 1080(3 Split)10463
10482 Rd.11729 Rd. Serr.
11232 Hx.11233 Sq.
# 4 Universal 1 3/4 1 3/4 1 1/2 1 1/4 1081(3 Split)11709
11710 Rd.11711 Hx.11712 Sq.
# 4 Universal 2 2 1 3/4 1 3/8 1082(3 Split) 19985
19992 Rd.19993 Rd. Serr.
19994 Hx.19995 Sq.
TURRET LATHE Conventional Style Collet Pads
8.
Note: Dimensional data and capacities are shown in inches. Specifications and dimensional data are subject to change with design improvements. All pads available soft or hardened to 58-60 Rc.Specials: We make collet chucks and pads to fit your application.
# 5 Universal7-A, 7-B, 7-D 2 1/2 2 1/2 2 1/4 1 3/4 1083
(3 Split)10464
10481 Rd.11725 Rd. Serr.
11236 Hx.115427 Hx. Serr.
11237 Sq.
# 5 Universal7-A, 7-B 3 3 2 5/8 2 1/8 1084
(3 Split)15246
15239 Rd.15502 Rd. Serr.
15421 Hx.15422 Sq.
# 5 Universal7-A, 7-B 3 1/2 3 1/2 3 2 3/8 1085
(3 Split)1989819896 Rd.19894 Hx.19893 Sq.
# 5 Universal7-A, 7-B 4 1/2 4 1/2 3 7/8 3 1/8 1086
(3 Split)1381880754 Rd.80756 Hx.80757 Sq.
JONES & LAMSON (continued)
90019002
9003
TURRET LATHE PAD NUMBER
1022, 1026, 1045, 1046, 1048, 1057, 1058, 1067, 1068, 10781025, 1027, 1071
1018, 1021, 1023, 1047, 1049, 1050, 1060, 1061,1063, 1081, 1082, 1097
5/163/8
5/16
SUPERIOR NUMBERSCREW SIZE
MACHINESIZE
MACHINEMODEL
SUPERIORNUMBER
MASTER COLLETNUMBER
MASTER PADNUMBERROUND HEXAGON SQUARE
COLLET PAD CAPACITY
Pad capacity limited by machine spindle bore.
TURRET LATHE Conventional Style Collet Pads
WARNER & SWASEY
# 2, # 3, #4, # 2EC, 16" EC
# 3# 4
1 1/2
1 3/42
33 1/2
1 1/2 1 5/16 1 1/16
2 1 3/4 1 3/8
# 51A 2 1/22 1/2 2 3/16 1 3/4
1027(3 Split)
1025(3 Split)
1026(3 Split)
461-1002462-1002
1369-1008
1129-11021369-1003
461-1003 Rd.461-1023 Hx.461-1024 Sq.
1129-1004 Rd.1129-1005 Hx.1129-1006 Sq.
471-1001471-1002 Rd.471-1003 Hx.471-1004 Sq.
1A2A 3 1/4 2 3/4 2 3/8 1024
(4 Split)404-1008404-1009 Rd.404-1028 Hx.404-1014 Sq.
3# 5 3 2 5/8 2 1/8 1022(3 Split)4669-1001
4669-1165 Rd.4669-1166 Hx.4669-1167 Sq.
4 1/2# 5 4 1/2 3 7/8 3 3/16
1018(3 Split)
1023(4 Split)
2779-10012779-1009 Rd.2779-1010 Hx.2779-1011 Sq.
4 1/22A3A 4 1/2 3 3/16 3 3/16 1021
(4 Split)533-1008533-1010 Rd.533-1011 Hx.533-1016 Sq.
63A 6 5 3/16 4 1/2 1014(3 Split)1959-7
1959-1003 Rd.1959-1004 Hx.1959-1005 Sq.
9.
90041014 7/16
Customer ServiceUSA: (800) 875-8175
Phone: (513) 272-1122Fax: (513) 272-0503
WHEN ORDERING COLLET PADS SPECIFY:Make of machine, machine size, machine model, number of sets required and Superior Cincinnati part number. One set of pads required for each spindle. A six spindle machine requires six sets of pads to equip a full machine; a single spindle machine requires one set. Special Collet Pads or items not shown on the above list are available on application and require a sketch or sample part for positive identification. Special discount based on quantity and cost justification available on application.
ACME-GRIDLEY (NATIONAL ACME)
1 1/4
2 1/4
2 5/8
3 1/2
4
G, G-4, GA-4, R, R-6,RA, RA-4, RA-6, RB-6, RB-8
GM32, GS32, AS32, AV32, GM32/6AV48, AS48, AA48
AV67, AS67
G, GA, R, R-4, RA, RA-4, RAS-4GA
C, G, GA, GA-4, R, R-4, R-6, RA, RA-4,RA-6, RA-8, RAS-4, RB, RB-6, RB-8
B, R, R-4, R-6, RA, RA-4, RA-6,RAS, RAS-4, RAS-6, RB, RB-6, RL
B, G, R, R-4, R-6, R-8,RA, RA-4, RA-6, RA-8, RL
G, G-4, GA-4, GR, M, R, R-6, R-8,RA, RA-6, RA-8, RB-6, RB-8
G, GA, M, MR, R-4, R-6, R-8,RA, RA-4, RA-6, RB-4, RB-6, RB-8
1 3/81 1/2
1 5/8
2
1 1/4
2 1/4
2 5/8
3 1/2
4
1 1/21 1/2
1 5/8
2
1 1/16
1 15/16
2 1/4
3
3 7/16
1 9/321 9/32
1 13/32
1 23/32
7/8
1 9/16
1 27/32
2 15/32
2 13/16
1 1/321 1/32
1 1/8
1 13/32
1212
1222
1226
1235
1240
1 5/82 3/8
1 1/22
1 1/41 1/2
1 7/8 & 22 1/4
2 1/2 & 2 5/83 & 3 1/4
3 1/245
1 1/41 1/21 5/8
22 1/4
22 5/8
2 1/42
2 5/8
2 19/3233 1/2
45
1 13/32
1 1/16
1 15/162 1/4
33 7/16
1 9/32
1 23/32
4 5/16
1 1/8
7/8
1 9/161 27/32
2 15/322 13/16
1 1/32
2 3/32
1 1/81 13/32
3 1/2
1 1/2 1 9/32 1 1/322 1 23/32 1 13/32
1216
12151220
121212151216
1222
1230123512401250
121212201226
121612201226
12152
12202
12262
1215
1216
1220
MACHINESIZE
MACHINEMODEL SUPERIOR
NUMBERROUND1 HEXAGON SQUARECOLLET PAD CAPACITY
"S" STYLE MASTER COLLET PADS
RB-6, RB-8BROWN & SHARPE
# 23B.S.A.# 138# 168CONE
GILDEMEISTER
Six SpindleSix Spindle
Four Spindle
GREENLEE
1 1/4 1 1/161 23/32
1 23/32
2 1/4
7/8
1 13/32
1 13/32
1 13/321 13/32
1 27/32
1 5/8
1 5/81 5/82 & 2 1/4
2 5/8
2 5/8
1 1/8
1 27/32
"S" STYLE Collet Pads For Single & Multiple Spindle Automatics
10.
22 5/8
1 1/4
Note: Dimensional data and capacities are shown in inches. Specifications and dimensional data are subject to change with design improvements. All pads available soft or hardened to 58-60 Rc.Specials: We make collet chucks and pads to fit your application.
"S" STYLE Collet Pads For Single & Multiple Spindle Automatics
1 Maximum capacity for round, serrated is 1/16" less than smooth except 1230, 1235, 1240 & 1250.2 Pad capacity limited by machine spindle bore.
HERBERT2
2 1/2
2 3/8
1 1/41 3/81 5/8
1 3/4 & 22 1/4
2 5/8 & 2 3/43 1/2
4
1 1/41 3/42 1/41 1/4
23
2 & 2 1/43
1 3/81 3/42 1/42 5/83 1/43 1/24 1/8
1 1/41 1/21 5/8
22 1/42 5/83 1/2
4
1 1/161 9/32
1 13/321 23/321 15/16
2 1/43
3 7/16
7/81 1/321 1/8
1 13/321 9/16
1 27/322 15/322 13/16
1 1/42
2 1/41 1/42 1/4
32 1/4
3
1 1/161 23/321 15/161 1/16
1 15/162 19/321 15/162 19/32
7/81 13/321 9/16
7/81 9/162 3/321 9/16
1 1/41 5/82 1/42 5/8
33 1/2
4
1 1/161 13/321 15/16
2 1/42 19/32
33 7/16
7/81 1/8
1 9/161 27/322 3/32
2 15/322 13/16
2 3/32
# 4# 5, 7
22 5/8
1 23/322 1/4
1 13/321 27/32
1 5/8 1 13/32 1 1/8
.111.145
4183-001-00014183-002-0002
4183-001-00004183-002-0000
12262
12162
12202
12152
1220
STYLE "S"PAD NUMBER
1212, 1215, 1216, 1220, 12261222, 1230, 1235, 1240, 1250
B SplineC Spline
CLAMPSSUPERIOR NUMBERWRENCH &
CLAMP TYPESPLINE
SIZE WRENCH
INDEX# B60
2 1 23/32 1 13/32 1220
1212
1222122612351240
1216
12202
12222
12222
1212
12221212
1212121612221226123012351240
1230
1230
MORI-SEIKI (SL-2)SL-2B
NEW BRITAIN# 52, 601, SL
1 5/8 1 13/32 1 1/8 1216TRAUB
A-56, A-60, TB-60, TS-60WARNER & SWASEY
OAB Six Spindle M-3300Five Spindle M-2500
1AB Single & Five Spindle M-2530
2AB Single Spindle M-3925, M-33801SC 5014-1006, 5034-1001
2SC, 2SC12, 5054-1003
1AB Single Spindle M-38800AB Single Spindle M-4415
WICKMANFive & Six Spindle
Five, Six & Eight SpindleSix Spindle
Single & Four SpindleSix Spindle
Six SpindleSingle & Six Spindle
# 52, 60, 601# 41, 61, 62
# 61, 415, 817# 61, 62
# 26 Single Spindle, 126, 626, 828# 635# 640
WRENCHES & CLAMPS FOR STYLE "S" MASTER COLLETS
MACHINESIZE
MACHINEMODEL SUPERIOR
NUMBERROUND1 HEXAGON SQUARECOLLET PAD CAPACITY
"S" STYLE MASTER COLLET PADS
11.
Customer ServiceUSA: (800) 875-8175
Phone: (513) 272-1122Fax: (513) 272-0503
MARTIN TYPE Collet Pads & Model "A" Feed Finger Pads
ACME-GRIDLEY (NATIONAL ACME)
1
2 5/8
3 1/2
44 3/4
5 1/8, 5 1/2
C, R, R-4, R-6,RA, RA-4, RA-6, RAN-6, RAS-6
G, G-4, GA-4, R, R-6,RA, RA-4, RA-6, RB-6, RB-8
C, G, GA, GA-4, R, R-4, R-6, RA, RA-4,RA-6, RA-8, RAS-4, RB, RB-6, RB-8
B, R, R-4, R-6, RA, RA-4, RA-6,RAS, RAS-4, RAS-6, RB, RB-6, RL
M, R, R-6, R-8,RA, RA-6, RA-8, RB-6, RB-8
M, MR, R-6, R-8,RA, RA-4, RA-6, RB-4, RB-6, RB-8
1 1/4
1 5/8
2
1
2 5/8
3 1/2
44 3/45 1/8
1 1/4
1 5/8
2
15/16
2 9/16
3 7/32
3 7/84 7/16
5
1 3/16
1 1/2
1 7/8
27/32
2 1/4
3
3 1/24
4 1/2
1 1/16
1 13/32
1 23/32
21/32
1 13/16
2 1/4
2 3/43 1/83 1/2
13/16
1 1/16
1 5/16
13/16
2 3/16
2 3/4
3 3/83 13/16
4 3/8
1
1 5/16
1 5/8
11/16
1 27/32
2 7/16
2 7/83 3/8 10423 5/8
7/8
1 5/32
1 13/32
1036
1038
1035
1017
1044
1031
1033
1037
2042
2036
2038
2035
2017
2044
2031
2033
2053
MACHINESIZE
MACHINEMODEL COLLET PAD CAPACITY
MARTIN TYPE1 MASTER COLLET PADS
SUPERIORNUMBER
SUPERIORNUMBER ROUND HEXAGON SQUAREROUND HEXAGON SQUARE
FEED FINGER PAD CAPACITYMODEL "A" FEED FINGER/PUSHER PADS
RB-6, RB-8M, RA-4, RB
M, RB-4
For Single & Multiple Spindle Automatics
2 1/2, 2 5/8
CONE4 Vertical & 6, SL, SK, SW, TC, TK 1
1 1/41 1/21 5/8
22 1/4
33 1/83 1/2
44 1/44 3/4
20602036
2032
20532033
2029203820342034
20172035
20192042
10311036
1032
10531033
1029103810341034
10171035
10191042
1 1/41
1 1/2
21 5/8
2 1/42 5/8
33
43 1/2
4 1/44 3/4
1 1/1627/32
1 9/32
1 23/321 13/32
1 15/162 1/4
2 9/162 9/16
3 1/23
3 5/84
7/811/16
1 1/32
1 13/321 5/32
1 19/321 27/32
2 1/82 1/8
2 7/82 7/16
33 3/8
1 3/1615/16
1 3/8
1 7/81 1/2
2 1/82 9/16
2 13/162 13/16
3 7/83 7/32
4 1/84 7/16
1 1/3213/16
1 3/16
1 5/81 5/16
1 27/322 3/162 7/162 7/16
3 3/82 3/4
3 9/163 13/16
27/3221/32
15/16
1 5/161 1/16
1 1/21 13/161 31/321 31/32
2 3/42 1/4
2 7/83 1/8
12.
4 & 6
55 1/4
6
20112044
101110441043
55 1/8
6
4 5/164 1/25 1/8
3 1/23 5/84 1/4
4 23/325
4 1/164 3/8
3 5/163 1/2
INDEX# C29 & B30# 36 & B42# 52 & B60
13/161 3/161 7/8
23/321 1/321 5/8
9/1627/32 20601 5/16
2030
20531
1 3/427/32
1 17/3211/16 10361 1/4 1040
NEW BRITAIN# 40, 51, 60, 226, 263, 408, 608
# 52, 601, SL# 41, 42, 61, 62, 415, 656
# 41, 42, 61# 41, 42, 61, 62, 415, 656
#26, 42, 126, 626, 826# 126, 635
# 450
11 1/41 5/8
5 1/4
22 1/42 5/83 1/2
15/161 3/161 1/2
5
1 7/82 1/8
2 9/163 7/32
13/161
1 5/16
4 3/8
1 5/81 27/322 3/162 3/4
21/3213/161 1/16
3 1/2
1 5/161 1/2
1 13/162 1/4
11 1/4
27/321 1/16
11/167/8
1 5/82
1 13/321 23/32
1 5/321 13/32
2 1/42 5/8
1 15/162 1/4
119/321 27/32
3 1/2 3 2 7/16
1036103110331037102810381035
20362031203320372029203820352044
Note: Dimensional data and capacities are shown in inches. Specifications and dimensional data are subject to change with design improvements. All pads available soft or hardened to 58-60 Rc.Specials: We make collet chucks and pads to fit your application.
MACHINESIZE
MACHINEMODEL COLLET PAD CAPACITY
MARTIN TYPE1 MASTER COLLET PADS
SUPERIORNUMBER
SUPERIORNUMBER ROUND HEXAGON SQUAREROUND HEXAGON SQUARE
FEED FINGER PAD CAPACITYMODEL "A" FEED FINGER/PUSHER PADS
1 1/41 3/42 1/4
4 1/2
1 1/423
2 1/2
3 1/2
34 1/2
43
2 & 2 1/4
10311040
10311052•10341026
10381017
10521034
1 3/41 1/4
2 1/4
2 1/41 1/4
32 1/2
52 5/8
4
2 1/43
4 3/4
1 3/41 1/4
2 1/8
2 1/81 1/4
2 13/16
4 7/16
3 7/32
2 9/164 7/16
2 1/83 7/324 7/16
1 17/321 1/16
1 27/32
1 27/321 1/16
2 7/16
3 13/16
2 3/4
2 3/163 13/16
1 27/322 3/4
3 13/16
1 1/47/8
1 1/2
1 1/27/8
1 31/32
3 1/8
2 1/4
1 13/163 1/8
1 1/22 1/43 1/8
1 17/321 1/16
1 15/16
1 15/161 1/16
2 9/162 3/164 5/162 1/43 1/2
1 15/162 9/16
4
1 1/47/8
1 19/32
1 19/327/8
2 1/81 3/43 1/2
1 27/322 7/8
1 19/322 1/83 3/8
1052
1011•
1042•
20612040
206120522034
2 13/16 2 7/16 1 31/32 2034
20352
203820422
2052
20522
2042
20422
20352
WARNER & SWASEYOAB Six Spindle M-3300
Five Spindle M-25001AB Five Spindle M-2530
2AB Single Spindle M-3925, M-33802AB Single Spindle M-3925, M-3380 (471)
3 AB M-3995SC15 M-4820-1SC15 M-4820-2SC15 M-4890
1SC 5014-1006, 5034-1001
2SC15, 2SCL 5094-10042SC, 2SC12, 5054-1003
1AB Single Spindle M-38800AB Single Spindle M-4415
MARTIN TYPE Collet Pads & Model "A" Feed Finger Pads
For Single & Multiple Spindle Automatics
13.
11 3/4
2
4 1/8
2 1/42 1/42 5/83 1/2
11 3/4
2
4
2 1/42 1/42 5/83 1/2
15/161 1/21 7/8
3 7/8
2 1/82 1/8
2 9/163 7/32
27/321 17/321 23/32
3 1/2
1 15/161 15/16
2 1/43
13/161 5/161 5/8
3 3/8
1 27/321 27/322 3/162 3/4
27/321 1/161 5/16
2 3/4
1 1/21 1/2
1 3/162 1/4
11/161 1/4
1 13/32
2 7/8
1 19/321 19/321 27/322 7/16
10361040103710521029103810351017
20362033205320522029203820352017
WICKMAN
Four & Six SpindleFive, Six & Eight Spindle
Six Spindle
AlteredSix SpindleFive Spindle
All Feed Finger Pads are supplied as hardened steel pads. Martin Collet Pads and Feeder/Pusher Pads are not returnable.
Lugs can only be used with Superior Cincinnati pads.
5/32 Hex
5/32 Hex
1/4 Hex
9009-002-0000
9009-001-0000
9009-003-0000
MARTIN PAD NUMBER
1011, 1016, 1017, 1019, 1028, 1029, 1034,1035, 1038, 1042, 1055
1010, 1031, 1032, 1033, 1036,1037, 1039, 1040, 1052
1043, 1074, 1087
3/8
1/2
3/4
SUPERIOR NUMBERLUG SIZE WRENCH SIZE
WHEN ORDERING COLLET PADS SPECIFY:Make of machine, machine size, machine model, number of sets required and Superior Cincinnati part number. One set of pads required for each spindle. A six spindle machine requires six sets of pads to equip a full machine; a single spindle machine requires one set. Special Collet Pads or items not shown on the above list are available on application and require a sketch or sample part for positive identification. Special discount based on quantity and cost justification available on application.
Customer ServiceUSA: (800) 875-8175
Phone: (513) 272-1122Fax: (513) 272-0503
1 All Martin Type Collet Pads are interchangeable with all Martin Type and Model "M" Masters.2 Pad capacity limited by machine spindle bore
14.
AUTOBLOK
HY-MCD MCD RCDRCA RCM RCC
10-590-12-A08
1749
91619171
91019111913191419151
10-590-15-A08
10-590-15-A1110-590-18-A11
91-430-10-A6
91-430-12-A8
12
15
1518
10
12
CUSHMAN
PRATT BURNERD
STYLE DIAMETER
6 1/28
101215
10271025102610221018
102710251026
10261026102610261018101810261026
1025
1026107810781078
10261022
1049 or 1018 w/Top Jaws
1049 or 1018 w/Top Jaws
1014 w/Top Jaws10271025102610221049
10141014101410261022
10221018
REFERENCE DESCRIPTION SUPERIOR NUMBER
04-225878
04-22587898-226441
98-226441
Round SmoothRound Serrated
Hexagonal SmoothHexagonal Serrated
Square SmoothSquare Serrated
Round SmoothRound Serrated
Hexagonal SmoothHexagonal Serrated
Square SmoothSquare Serrated
98-226716
98-214630
98-22771898-22679298-226793
98-22587898-226441
0241002420
03520 (Discontinued)03560 (Discontinued)
02400
X21XXX26XX
X21XXX26XX
X17XX
X38XXX46XX
X31XX
660XX760XX
X50XX
98-226760
8 1/410121620
6 1/28 1/4
8 1/410.43
10121518202424
JAW CHUCK PADS
Note: Dimensional data and capacities are shown in inches. Specifications and dimensional data are subject to change with design improvements. All pads available soft or hardened to 58-60 Rc.Specials: We make collet chucks and pads to fit your application.
Round SmoothRound Serrated
Hexagonal SmoothHexagonal Serrated
Square SmoothSquare Serrated
SP – ITW WORKHOLDING
10491049
15CC-32518CC-325
1518
15CC18CC
10261022
10418CC-32510CC-32512CC-325
81012
8CC10CC12CC
Round SmoothRound Serrated
Hexagonal SmoothHexagonal Serrated
Square SmoothSquare Serrated
Wide RangeSerrated
15.
CUSHMANSTYLE DIAMETER REFERENCE DESCRIPTION SUPERIOR NUMBER
JAW CHUCK PADS (continued)
X – Denotes any number or letter (or series of numbers or letters) within a particular product line.Wide Range pads are only available with serrated I.D.
ITEM/SERIES HURON TOP JAW CHUCK CAPACITY SUPERIOR NUMBERKITAGAWA
DESCRIPTION
B206 B206 CPJ 1027 1.750 1027B208 CPJ 1027B208 CPJ 1025B208 CPJ 1026
B208 2102710251026
B210 CPJ 1022B210 CPJ 1025B210 CPJ 1026B210 CPJ 1027
B210 2.953
1022102510261027
B212 CPJ 1022B212 CPJ 1025B212 CPJ 1026
B212 3.583102210251026
B215 CPJ 1018B215 CPJ 1022
B215 410181022
B218 CPJ 1018B218 CPJ 1049
B218 Please call for availability10181049
Customer ServiceUSA: (800) 875-8175
Phone: (513) 272-1122Fax: (513) 272-0503
Round SmoothRound Serrated
Hexagonal SmoothHexagonal Serrated
Square SmoothSquare Serrated
10471057
98-226791-XX98-226418-XX
1810
10-590-18-A1191-430-10-A6
10481047
104898-226860-XX98-226860-XX98-226791-XX
121515
10-590-12-A0810-590-15-A0810-590-15-A11
SP-ITW WORKHOLDING
105018CC-355-X18FACC180, CC180
10461050
104510CC-355-X12CC-355-X15CC-355-X
101215
FACC100, CC100FACC120, CC120FACC150, CC150
Wide RangeSerrated
105898-233613-XX1291-430-12-A8
FOR ILLUSTRATION PURPOSES ONLY
16.
CDSCNSCRS
COLLET CHUCK PADS
ITEM/SERIES CHUCK CAPACITY CHUCK MODEL NUMBER DESCRIPTION SUPERIOR NUMBER
CDS-16, CNS-16, CRS-16
CDS-22, CNS-22, CRS-22CDS-26, CNS-26, CRS-26CDS-30, CNS-30, CRS-30
CDS-40, CNS-40, CRS-40
1 5/8
2 1/42 5/8
3
4
1216
122212261230
1240
SUPERIOR CINCINNATI
CDS-20, CNS-20, CRS-202 1220
CDS-35, CNS-35, CRS-353 1/2 1235
CNT-15, CRT-15CNT-20, CRT-20CNT-25, CRT-25CNT-30, CRT-30CNT-45, CRT-45CNT-60, CRT-60
CDDCDD-15CDD-20
CNTCRT
1 1/22
2 1/23
4 1/26
1 1/22
10271025102610221049101410711025
ATS732A01SJ55-XXX 2 XX-S20TLS PS 1220732APPX01-XX
726A01SC318-XXX782ASC321-XX
782APP785F111-XX
740AC322-XX415XX-XXX
415XXX-XXX420XXX-XXX420XXX-XXX422XX-XXX
426XXX-XXX426XXX-XXX430XXX-XXX435XXX-XXX440XX-XXXX450XX-XXX
22 5/8
33
3 1/24
1 1/21 1/2
22
2 1/42 5/82 5/8
33 1/2
45
XX-S20TL PPXX-S26TLS PS
XX-S30TLSXX-S30TL PPXX-S35TLSXX-S40TLS
XXXXX-S15HXX-S15W
XXXXX-S20H, HSXX-S20WXX-S22H
XX-S26H, HSXX-S26W
XX-S30H, HSXXX-S35H, HSXXX-S40H, HS
XX-S50H
12201226123012301235124012151027122010251222122610261230123512401250
Round SmoothRound Serrated
Hexagonal SmoothHexagonal Serrated
Square SmoothSquare Serrated
CB-NB/S
CB-ND/S
CB46-NB/S16CB65-NB/S20CB65-NB/S22CB80-NB/S26CB80-NB/S30CB65-ND/S20CB65-ND/S22CB80-ND/S26CB80-ND/S30
121612201222122612301220122212261230
MICROCENTRIC1 5/8
22 1/42 5/8
32
2 1/42 5/8
3
Note: Dimensional data and capacities are shown in inches. Specifications and dimensional data are subject to change with design improvements. All pads available soft or hardened to 58-60 Rc.Specials: We make collet chucks and pads to fit your application.
Round SmoothRound Serrated
Hexagonal SmoothHexagonal Serrated
Square SmoothSquare Serrated
Round SmoothRound Serrated
Hexagonal SmoothHexagonal Serrated
Square SmoothSquare Serrated
Customer ServiceUSA: (800) 875-8175
Phone: (513) 272-1122Fax: (513) 272-0503 17.
CB-NDR/S
CB65-NDR/S20CB65-NDR/S22CB80-NDR/S26CB80-NDR/S30
1220122212261230
MICROCENTRIC (continued)2
2 1/42 5/8
3
COLLET CHUCK PADS (continued)
ITEM/SERIES CHUCK CAPACITY CHUCK MODEL NUMBER DESCRIPTION SUPERIOR NUMBER
CB-NS/SCB46-NS/S16CB65-NS/S20CB65-NS/S22
121612201222
1 5/82
2 1/4
2 PB20-XX
Round SmoothRound Serrated
Hexagonal SmoothHexagonal Serrated
Square SmoothSquare Serrated
1220
PRATT BURNERD
FBXX-XXX
FB6-20FB8-20FB8-27
FB10-30FB10-32AFB10-32BFB11-31FB11-40FB14-55
122012201226122612301230123012351250
Round SmoothRound Serrated
Hexagonal SmoothHexagonal Serrated
Square SmoothSquare Serrated
PRODUCTION DYNAMICS (DIVISION OF LEXAIR, INC.)22
2 5/82 5/8
333
3 1/25
ROYAL PRODUCTSAccu-LengthTM
42974, 42976 2 ALS-20 1220
Smart Chuck Series42809, 42812
42813, 42815, 42818
45108
1 5/82
2 5/822
2 5/8
CDC-54QCCDC-66QCCDC-80QC
S-20S-20S-26
12161220122612201220
12261230
12262 5/8 S-26
3 S-30
4511045112451144511545116451184511945120
33 1/2
44
S-30S-35S-40S-40
1230123512401240
Round SmoothRound Serrated
Hexagonal SmoothHexagonal Serrated
Square SmoothSquare Serrated
Round SmoothRound Serrated
Hexagonal SmoothHexagonal Serrated
Square SmoothSquare Serrated
X – Denotes any number or letter (or series of numbers or letters) within a particular product line.Accu-LengthTM is a registered trademark of Royal Products.
Customer ServiceUSA: (800) 875-8175
Phone: (513) 272-1122Fax: (513) 272-0503
Note: Dimensional data and capacities are shown in inches. Specifications and dimensional data are subject to change with design improvements. All pads available soft or hardened to 58-60 Rc.Specials: We make collet chucks and pads to fit your application.18.
FX-175 1.25 1032FX-205FX-225FX-306FX-338FX-520FX-543FX-830FX-835FX-845
FX-1050FX-1150FX-5011
1.802.252.603.002.002.252.623.254.254.75
103510291038103410531052103810341019104210421042
Round SmoothRound Serrated
Hexagonal SmoothHexagonal Serrated
Square SmoothSquare Serrated
ITEM/SERIES CAPACITY WITH PAD DESCRIPTION SUPERIOR NUMBERFLEX-E-ON MARTIN S-STYLE
1215121612221226123012201222122612351250125012501250
COLLET CHUCK PADS (continued)
4.624.60
CUSTOM QUOTE REFERENCE GUIDE
Hexagon EccentricTo Corner
Hexagon EccentricTo Flats
Square EccentricTo Corner
Square EccentricTo Flats
Rectangle Eccentric-Short Side
Rectangle Eccentric-Long Side
Octagon EccentricTo Corner
Octagon EccentricTo Flat
RoundEccentric
Triangle
1. Order Hole Size:2. Order Hole, 2nd:3. Radius:4. Relief Diameter:5. Relief Length:
6. Depth of Step, 1st:7. Depth of Step, 2nd:8. Length of Extension:9. Off Center Distance:
19.
Call Customer Service to OrderUSA: (800) 875-8175
Phone: (513) 272-1122Fax: (513) 272-0503
e-mail: [email protected] through Friday, 8:00 A.M. – 5:00 P.M. EST3894 Virginia Avenue Cincinnati, Ohio 45227-3410
www.superiorcincinnati.com
Orders and requests for information are accepted through our distributor network; by telephone, facsimile, U.S. mail or e-mail. Orders placed incorrectly may be subject to a 20% restocking charge(s).
To place an order, check pricing, availability or to inquire about expediting services, please contact your local Superior Cincinnati distributor. Please be prepared to give the following information:Company Name or Customer NumberName and Telephone NumberAddressP.O. or Credit Card Number(MasterCard, Visa, American Express or Discover/Novus)A complete description of item(s) being ordered:Quantity Part Number(s)Delivery Date Required Shipping Preference
Open account credit is extended to companies with satisfactory credit references. If credit references are not quickly available, advanced payment, or credit card payment will speed up your first order.
Pads for master collets and feed finger pads are available from stock in round, hexagon and square shapes. Unique shapes, eccentric, rectangles, octagons or off-center holes, can be custom made with the help of our customer service department. Collet and Feeder Pads are available in a variety of materials including high quality alloy steel, cast iron, bronze and nylon to meet your workholding needs.
Open account credit terms are net 30 days.Special collet pads made to customer specificationare not returnable.
Standard Equipment All collet chucks come factory lubricated and ready for installation. Maintenance instructions, spindle adapter, drawtube adapter, and mounting bolts are included.
Machine Information: Manufacturer Model Serial NumberSpindle Information: 1. Spindle Nose 2. Spindle Thread Size 3. Diameter 4. Length/Depth 5. I.D. Taper/CounterboreDrawtube/Drawbar Information: 6. I.D.Thread 7. O.D. Thread Thread LH or RH 8. Length of Thread 9. Drawtube I.D. 10. Drawtube/Drawbar O.D. 11. Maximum (Forward) 12. Minimum (Retracted)
Placing an Order or Requesting Information
Customer Service & Quotations
New Customers
Terms
Shipping
Collet Chuck Information Needed
Examples
We offer same day shipping on all in stock items ordered by 4:30 P.M. EST.
20 Steel21 Cast Iron22 Bronze
23 Nylon24 Square Face Steel25 Aluminum
10261026102610261026102610261026
15001500150015001500150015000000
1 1/2" Round Smooth – Steel1 1/2" Round Serrated – Steel1 1/2" Round Serrated – Cast Iron1 1/2" Hexagon Smooth – Bronze1 1/2" Square Smooth – Nylon1 1/2" Hexagon Serrated – Steel1 1/2" Square Serrated – SteelEmergency Collet Pad – Steel
200201211222233204205206
––––––––
––––––––
Collet Pad Ordering Instructions
XX = Material
1025 – XX0 Round Smooth – 1500 = (1 1/2") XX1 Round Serrated Four digit decimal XX2 Hexagon Smooth equivalent of the XX3 Square Smooth the size in inches XX4 Hexagon Serrated multiplied by 1000 XX5 Square Serrated XX6 Emergency XX7 Eccentric XX8 Octagon XX9 Rectangular XX10 Octagon Serrated
SuperiorCincinnatiSeries No.
I.D. Type I.D. Size