1 1 1 4 2 2 3 5 8 10 11 12 10 9 8, 9 5, 6 2, 3 1 4 7 7 6 1 + 2 + 3 + 4 11, 12 Colosseum, Italy: Assembly Instructions Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Y.Watanabe Assembly Instructions Mountain fold(dotted line) Make a mountain fold. Valley fold(dashed and dotted line) Make a valley fold. Scissors line(solid line) Cut along the line. Cut in line(solid line) Cut along the line. Glue spot(Red dot) Glue parts with the same number together. Glue spot(Green dot) Glue within the same part. Glue spot(Blue dot) Glue to the rear of the other part. Glue The glue spot(colored dot) shows where to apply the glue. Tools and materials Assembly tip Caution Scissors, set square, glue(We recommend stick glue), pencil, used ballpoint pen, toothpicks, tweezers, (useful for handling small parts) Before gluing, crease the paper along mountain fold and valley fold lines and make sure rounded sections are nice and stiff. Glue, scissors and other tools may be dangerous to young children so be sure to keep them out of the reach of young children. View of completed model Assembly Instructions:Two US letter sheets(No.1 to No.2) *This model was designed for Papercraft and may differ from the original in some respects. *Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper , easier fold. *Build the model by carefully reading the Assembly Instructions, in the parts sheet page order. Indicates where sections should be glued together. Before starting assembly:Writing the number of each section on its back side before cutting out the sections is highly recommended. (* This way, you can be sure which section is which even after cutting out the sections.) When gluing parts 1 and 2 together, align the triangles on the ends of part 1 to the seams on part 2. Top Bottom Fold outward Fold inward The illustration below is a close-up of parts 2, 3, 5, 6, 8, and 9.Be sure to fold the top and bottom parts correctly. http://www.canon.com/c-park/en/
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
7/25/2019 Coliseum Instrucciones
http://slidepdf.com/reader/full/coliseum-instrucciones 1/2
1
1
1
4
2
2
3
5
8
10
11
12
10
9
8, 9
5, 6
2, 3
1
4
7
7
6
1 + 2 + 3 + 4
11, 12
Colosseum, Italy: Assembly Instructions Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Y.Watanabe
Assembly Instructions
Mountain fold(dotted line)Make a mountain fold.
Valley fold(dashed and dotted line)
Make a valley fold.Scissors line(solid line)Cut along the line.
Cut in line(solid line)Cut along the line.
Glue spot(Red dot)
Glue parts with the same number together.
Glue spot(Green dot)Glue within the same part.
Glue spot(Blue dot)Glue to the rear of the other part.
Glue
The glue spot(colored dot)shows where to apply the glue.
Tools and materials
Assembly tip
Caution
Scissors, set square, glue(We recommend stick glue), pencil, usedballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valleyfold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young childrenso be sure to keep them out of the reach of young children.
View of completed model
Assembly Instructions:Two US letter sheets(No.1 to No.2)*This model was designed for Papercraft and may differ from the original in some respects.
*Hint: Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold.
*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order.
Indicates where sectionsshould be glued together.
Before starting assembly:Writing the number of each section on itsback side before cutting out the sections is highly recommended.(* This way, you can be sure which section is which even after cutting out
the sections.)
When gluing parts 1 and 2 together,
align the triangles on the ends of part 1 tothe seams on part 2.
Top
Bottom
Fold outward
Fold inward
The illustration below is a close-up ofparts 2, 3, 5, 6, 8, and 9.Be sure tofold the top and bottom parts correctly.
http://www.canon.com/c-park/en/
7/25/2019 Coliseum Instrucciones
http://slidepdf.com/reader/full/coliseum-instrucciones 2/2
2
13, 14
15, 16
1413
1817
15
16
23
24
21 19
22
20
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © Y.Watanabe
Parts 1 - 12
Parts 17 + 18Stand
Glue parts 19 and 20 along the topof parts 21 - 22.
Glue the 16 glue tabs on parts 19 - 24
to the oval on the stand.
When gluing parts 19 - 24 to the stand,be sure the seams of all parts line up asshown in the illustration.
Finished!
Parts 19 - 24
Colosseum, Italy: Assembly Instructions
Related Documents
