OPERATION MANUAL COLD, AMBIENT & HOT WATER DISPENSER H2O-PRO Intended for water pressure between 25~60 psi. If water pressure is more than 60 psi, please use a water pressure regulator. Please read these instructions completely before operating this unit Page Contents 1 3 4 2 Installation & Set-Up Preface Leak Detection, Cleaning & Maintenance Replacing Filters & Safety Reminders PREFACE Please read the instructions completely before using this product. Top Cover Small Cover Drip Tray Cold Water Tank Hot - Water Button Ambient - Water Button Cold - Water Button Heating System Indicator Hot Power Indicator Cold Power Indicator
4
Embed
COLD, AMBIENT & HOT WATER DISPENSER › docs › fw › fw-pro-manual.pdf · To dispense cold or ambient water, please press the cold or ambient water button. 4. To dispense hot water,
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
OPERATION MANUAL
COLD, AMBIENT & HOT WATER DISPENSER
H2O-PRO
Intended for water pressure between 25~60 psi. If water pressure is more than 60 psi, please use a water pressure regulator.
Please read these instructions completely before operating this unit
Please read the instructions completely before usingthis product.
Top Cover Small Cover
Drip Tray
Cold Water Tank
Hot - Water Button
Ambient - Water Button
Cold - Water Button
Heating System Indicator
Hot Power Indicator
Cold Power Indicator
2. WATER DISPENSER SET-UP
1- Take apart your water tap. Then put on the EZ Angle Connector valve.See drawing (A)
2- Connect the 1/4" PE water line between the EZ Angle Connectorand the Water In Connector on the back of your H2O-PRO.See drawing (B) .
1. WATER LINE SET-UP
3. H2O-PRO OPERATION
3. To dispense cold or ambient water, please press the cold or ambient water button.4. To dispense hot water, press the hot water button twice. (First to unlock, Second to dispense)5. Water will stop dispensing when any of the three water buttons is pressed over 60 seconds. Please let go of the water button and press again for more water.
1- After water line is connected, please plug in the water cooler to anelectrical outlet. Push any water buttonto begin filling the water tanks. Please wait at least 5 minutes, before pushing the hot water button, to check that wateris dispensing. DO NOT TURN ON HOT WATER POWER SWITCH UNTIL WATER ISDIPENSING FROM HOT WATER BUTTON. This part is very important to preventdry-heating of the hot water tank. As soon as heating process is done, you may push hot water button for hot water.
**Please push hot button twice before hot water can be drained. (The first pressunlocks the safety. The second press dispenses hot water)
2- Turn on cold power switch.Cooling takes about 40 minutes. After cooling is complete, please push cold button for cold water.
As a safety measure, water dispensing stops after 1 minute. If you need more water, please press the water button again.
2
Cold Power Switch
Hot Power Switch
Drawing ( B )
Water - In Connector
1/4" PE Water Pipe
Drawing ( A )
FaucetEZ Angle Connector
EZ Angle Connecto
REPLACEMENT OF FILTERSDrawing 1, push the latch ( A ) to open the top lid ( B ). Drawing 2, push the latch ( C ) in the filter head to allow the filtration system pop off. Drawing 3, Remove the filter clockwise.Drawing 4, Install the filter anti-clockwise. Drawing 5, Replace the filtration system. Drawing 6, Replace the top lid.
3
PushC
2
B
A
1
Twist in clockwise direction to remove
Twist in Counterclockwise direction to install
3
4 5
6
SAFETY REMINDER
6 INCHES
Leave at least 6 inches of clearance between the wall and the back of your unit.
Keep the machine away from sunlight , heat , and water.
Be sure to use single outlet socket with correct power voltage . Plug the power cord directly into electrical socket .
LEAK DETECTION CLEANING AND MAINTENANCEWhen the leak detector is activated:- LED light in the front tap will flash as alert. - Disconnect the electricity.- Remove the side panel , wipe off the water that remains in the detection probes and base panel.
- Put back the side panel and detection probe.
- If leaking continues, p l e a s e c o n t a c t u s i m m e d i a t e l y