CMS ECAL End Cap Meeting CERN19 June to 23 June 2000 A.B.Lodge - RAL 1 ECAL End Cap High Voltage Cards and 2000 Electrical/Thermal Model. Progress on High Voltage Cards & 2000 Electrical/Thermal Model. ECAL WEEK End Cap meeting held 19 June to 23 June at CERN Prepared by A.B.Lodge.
49
Embed
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 1 ECAL End Cap High Voltage Cards and 2000 Electrical/Thermal Model. Progress on.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 1
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
Progress on High Voltage Cards & 2000 Electrical/Thermal Model.
ECAL WEEK End Cap meeting held 19 June to 23 June
at CERN
Prepared by A.B.Lodge.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 2
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
Status Report Structure.
• High Voltage PCB Design, Manufacture and Test.
• 2000 Electrical/Thermal Model at RAL.• Single Channel Test Box (Thermal/Electrical Tests).• 10 Channel Readout Module (RS Pre-amps).• 10 Channel Dummy Readout Module (Thermal Tests).
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 3
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
Review of High Voltage PCBs
Individual Card Assembly and Test.
• Ten New High Voltage Filter Cards have been received and assembled (using conventional components) at RAL.
• Two Low Voltage Signal Termination Cards have also been assembled.
• The combined sets of cards are enough to provide high voltage filtering for 2 Super Crystal Modules (2000 Electrical/Thermal Model).
• All of the High Voltage cards have been tested with an Anode voltage of 1KV and a Dynode voltage of 0.8 KV.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 4
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
• High Voltage 5 Channel Filter Card.
Centre Ground Plane to close to the edge of PCB
ie. Increased risk of HV break down.
Via connecting Anode and Dynode together
ie. Needed drilling out to prevent a short.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 5
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
• High Voltage Filter Card set for 1 Super Crystal Module (Dynode Side shown) with Signal Termination Card.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 6
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
• High Voltage Filter Card set for 1 Super Crystal Module (Anode Side shown) with Signal Termination Card.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 7
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
• High Voltage Filter Card set for 1 Super Crystal Module.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 8
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
• High Voltage Filter Card set for 1 Super Crystal Module with Positional Spacer Fitted.
This shows the space available for the insertion of Monitoring Fibres.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 9
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
2000 Electrical/Thermal Model.
It has been agreed that the design team at RAL will produce a 2000 Electrical / Thermal Model as part of its Development Programme for the ECAL End Cap design proposal during this year.
This Model will be used to carryout full Thermal and Electrical testing of the complete detector designs proposed at this time including:
• Full Mechanical/Electrical Structure of the SCM design.• Back Plate and Back Plate Cooling design proposals.• Mechanical mounting and layer structure (Monitoring System,
Moderator, Back plate Cooling, Umbilical, Low Voltage, High Voltage, Readout Electronics(RS Pre-Amps) and Cooling, etc….
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 10
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
2000 Model Structure.
• Two Full Super Crystal Module.• High Voltage Filtering System.• Positional Spacers (2 Off).• Section of Back Plate (Large enough for 4 SCMs).• Back Plate Cooling System.• Moderator.• Low & High Voltage System + Cabling.• 50 Channels of Readout Electronics (initially using RS pre-
amps) based on final design.• Readout Electronics Cooling System.• Environmental Enclosure.• Full Mechanical Support Structure base on final design.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 11
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
2000 Model Development Programme.
Part of this development programme is to design and manufacture a 50 channel readout module. This module is to be as close as is possible (thermally and mechanically ) to the final design for the ECAL EE Readout Electronics. To achieve these goals we need to full understand:
• Full Mechanical/Electrical Structure of the 50 Channel Readout Module based on the EB design proposals.
• The full Thermal requirements and limitations of our Readout Module design.
• Is there any adverse interaction between Thermal / Mechanical and Electronics designs which will reduce system performance.
Due to the fact that the real electronics cards will not be available in the time scales required by this development programme we will be forced to use RS Pre-amps to carry out this work.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 12
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
Single Channel Test Box containing RS single channel pre-amp.
Numbers 1 to 6 represent positions of PT100 thermal sensors.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 13
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
Amplifier card shown with its mounting bracket. Amplifier mounted component side towards metal bracket on 4mm long spacers. Various different thermal compounds were used to transfer the heat from the amplifier card into the metal bracket.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 14
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
The amplifier in the Single Channel Test Box was powered for approximately 1 hour to allow it to reach a stable operating temperature.
• Each of the PT100 were then measured to obtain temperature measurements.
• Both Amplifier noise and gains were measured.
These tests were repeated using a number of different thermal compounds and the results plotted.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 15
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
0
5
10
15
20
25
30
35
40
Temp (C)
None Raychem Warth Birgquist
Graph of temperature vs thermal compound
PT 1PT 2PT 3PT 4PT 5PT 6
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 16
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
0
5
10
15
20
25
30
35
40
Temp (C)
PT 1 PT 2 PT 3 PT 4 PT 5 PT 6
Graph of temperature vs thermal compound
NoneRaychemWarthBirgquist
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 17
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
Amplifier Noise Measurements.
• The electron noise of the amplifier was measured for each type of thermal compound.
• This was done by feeding in 16mV through a 1pF capacitor, which gives 105 electrons into the amplifier I/P.
• The output pulse was then measured (OP).
• Noise of the circuit was measured with (Npowered) and without power (Nunpowered), using a calibrated true RMS voltmeter.
Noise e- =(((Npowered-Nunpowered)0.5)*105)/OP
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 18
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
0
200
400
600
800
1000
1200
1400
Noise (e-)
Graph of noise vs thermal compound
NoneRaychemWarthBirgquist
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 19
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
1250126012701280129013001310132013301340
Noise (e-)
Graph of noise vs thermal compound
NoneRaychemWarthBirgquist
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 20
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
The results of these limited test were favourable so we continued with the Design Development Programme for the 2000 Electrical / Thermal Model by designing and manufacturing the following:
• 10 Channel Readout Module.– The design is based on the present design proposal for the
ECAL EE Electronic Readout Modules.• 10 Channel Dummy Readout Module.
– This module is also based on the same design but will be used to conduct more extensive thermal analysis on the
requirements for the final EE Readout Module Design.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 21
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
Two boards with five amplifier cards on each.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 22
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
Another view of the boards showing the protection network.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 23
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
Boards fixed together using tapped and threaded spacers.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 24
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
Another view of the boards.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 25
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
Two views of the completed 10 channel assembly.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 26
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
144014501460147014801490150015101520153015401550
Noise(e-)
Noise figures for each channel on a 10 channel module
12345678910
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 27
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
Again the results of these preliminary tests were favourable so we intend to continue and finalise the design and manufacture of the 5 * 10 Channel Readout Modules needed for the 2000 Electrical / Thermal Model.
– To date we have five sets of readout cards at this level of manufacture.
– This includes the Mechanics for all 10 channel modules.
Work Remaining to complete the Readout Module includes:
The final design and manufacture of the 50 Channel Readout Box.
The design and manufacture of the interconnection method between the Umbilical (50 way D-Type connectors) and the Signal I/P of the 5 channel readout Cards.
Final Cooling System design and manufacture for the 50 Channel Readout Module.
Full Electrical and Thermal testing, etc…
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 28
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
• 10 Channel Readout Module (Thermal Model).
RM Side Covers.
RM Fixing Plate.
RM Base Plate.
RM Cooling Plate.
RM Cooling Pipe.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 29
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
• 10 Channel Readout Module (Thermal Model).
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 30
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
• 10 Channel Readout Module (Thermal Model): Showing the simplified support structure for the readout cards.
Thermal Gaskets Required
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 31
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
• 10 Channel Readout Module:
Showing Cooling Plate with single cooling pipe.
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 32
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
• 10 Channel Readout Module (Thermal Model).
• Board 2 showing the positions of the PRT100 temperature sensors:
– Board-1-TOP
– Board-1-MID
– Board-1-BOT
– Board-1-BTOP
– Board -1 BBOT
Board-1-TOP
Board-1-BOT
Board-1-BTOP
Board-1-BBOT
Board-1-MID
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 33
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
• 10 Channel Readout Module (Thermal Model).
• Board 2 showing the positions of the PRT100 temperature sensors:– Board-2-TOP– Board-2-BOT
Board-2-TOP
Board-2-BOT
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 34
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
• 10 Channel Readout Module (Thermal Model).
• Complete Readout Module with all Covers and Cooling Plates showing the positions of the PRT100 temperature sensors:
– Cover-1-TOP
– Plate-1-TOP
– Plate-2-BOT
Plate-1-TOP
Plate-2-BOT
Cover-1-TOP
CMS ECAL End Cap Meeting CERN 19 June to 23 June 2000 A.B.Lodge - RAL 35
ECALEnd Cap
High Voltage Cards and 2000 Electrical/Thermal Model.
Dummy Readout Card Structure and Measurement.
• Each card contained 25 Surface Mount resistor packs to represent the real Readout Electronics.
• Each resistor pack had 7 * 470ohm resistors connected in parallel (~ 67ohms).
• All Resistor packs on each card were again connected in parallel resulting in a total resistive load for the 10 Channel Module of ~ 1.34 ohms.
– By varying the supply voltage to the module we could set the module power dissipation.
• Simple PT100 temperature sensors were used to measure the relative changes in temperature during testing.