TO SET OUTPUT DURATION The receiver can be set for either constant or momentary closure on the output contacts for each channel (A and B). (Use constant closure only if constant pressure is needed.) With the jumper in “1” (Momentary) position, the contacts will close for 150ms regardless of the length of radio transmission. With the jumper in “2” (Constant) position, the contacts will stay closed as long as the radio continues transmitting. CM8002ANZ-1 433MHz 2 Channel Billion and Rolling Code Channel Receiver Constant signal (Hold to run) Momentary A nt OUT A OUT B Input AC / DC LearnA LearnB Test Test A B LDS2 LDS1 LDS3 LDS4 Jumper Channel A Program buttons (Channel A & B ) Command buttons (Channel A & B) Indicator lights (Channel A & B) Jumper Channel B Antenna Connection >24V < 24V Transformer or Power Source CN2 CN1 Indicator lights (momentary or constant) < 24V 12-16V ~ , @ 30mA 12-24V , @ 30mA > 24V 16-30V ~ , @ 30mA 24-30V , @ 30mA MERLIN MERLIN Example of use Gate Controler Example of Use Garage door motor Chamberlain Australia Pty Ltd PO Box 1446 Lane Cove NSW 1595 Chamberlain New Zealand Ltd PO Box 100 221 North Shore 0745 gomerlin.com.au gomerlin.co.nz CM842 CM128 C940 C943 C945 CM844 4330A 4333A 4335A Compatible Remotes: Merlin Professional Compatible Remotes: Chamberlain Open Garage door Channel A Open Garage and Gate Channel A and B Open Gate Channel B Example of Use __ _ _ _ __ _ _ _
2
Embed
CM8002ANZ-1 433MHz 2 Channel Billion and gomerlin.com.au ...
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
TO SET OUTPUT DURATIONThe receiver can be set for either constant or momentary closure on theoutput contacts for each channel (A and B). (Use constant closure only ifconstant pressure is needed.) With the jumper in “1” (Momentary) position,the contacts will close for 150ms regardless of the length of radiotransmission. With the jumper in “2” (Constant) position, the contacts willstay closed as long as the radio continues transmitting.
Chamberlain Australia Pty LtdPO Box 1446Lane Cove NSW 1595
Chamberlain New Zealand LtdPO Box 100 221North Shore 0745
gomerlin.com.augomerlin.co.nz
CM842 CM128
C940 C943 C945
CM844
4330A 4333A 4335A
Compatible Remotes:Merlin Professional
Compatible Remotes:Chamberlain
Open Garage doorChannel A
Open Garage and GateChannel A and B
Open GateChannel B
Example of Use
___ _ _
___ _ _
NOTE: The CM8002ANZ-1 can be programmed to receive up to 15 codes for each channel.
INSTALLATION1. Fasten the receiver securely with screws through the corner holes which are located under the cover.
2. Apply power to the AC/DC terminals on the circuit board (see illustration). Ensure the Power input link is in the correct position to suit the supply voltage.
3. Connect operator control board to the terminals (Channel A) of the Universal Receiver. At the same time connect any other hardwired inputs in parallel (i.e.output is Normally Open). Connect any secondary hardwired inputs (if you haveto operate 2 doors) to terminals. (Channel B).
4. Plug in the transformer or apply power.
5. Ensure the door or gate is safe to use then press the Test button for Channel A or B to test your device.
SPECIFICATIONSOutput Rating ...........................Out put max. = 5 A; V max. = 30V AC/DCPower input <24V ...............................................12-16V ~ 50/60Hz, @30 mA............................................................................................. 12-24V , @30 mA
DISCONNECT POWER TO GARAGE DOOR OPENER BEFORE INSTALLINGRECEIVER.
114A4786D
PROGRAMMING THE RECEIVER
1. Press and hold the remote control push button.
2. Press and release the Learn buttonfor the channel you wish to use.The indicator light will flash once.
3. Release the remote push button.
NOTE: If you release the remote control push button before the indicator lights flash, the opener will not accept the code.
Repeat steps 1–3 to program the receiver for all remote controls in use for that door. If a second door is in use, use adifferent remote control button and repeat the steps for channel B.
Replace top cover with mounting screws.
To erase all codes from the receiver: hold the receiver’s Learn button until the indicator light goes off (after 6 seconds). Allcodes that the receiver has learned will be erased.
LearnA LearnB
Tes tTes t
A BLDS 3 LDS 4
Activate the opener only when door is in full view, free of obstruction and properlyadjusted. No one should enter or leave garage while door is in motion. Do not allowchildren to operate push button(s) or remote(s). Do not allow children to play near thedoor.
NOTE: For voltage output terminal, the peak voltage shall not exceed 42.4 V