This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
PRODUCT FAMILY DATA SHEET
Cree LED / 4400 Silicon Drive / Durham, NC 27703 USA / +1.919.313.5330 / www.cree-led.com
Red Any 1 Intensity bin from H(355) - np(805) RB 619 RB 624 Reel
Green Any 1 Intensity bin from M(710) - P(1400) Any 1 hue bin from G7(520)-Ga(540) Reel
Blue Any 1 Intensity bin from D(140) - G(355) Any 1 hue bin from B3(460)-B6(480) Reel
CLY6C-FKC-Chj1qr1E1BB7D3D3
Red Any 1 Intensity bin from hj(403) - np(805) RB 619 RB 624 Reel
Green Any 1 Intensity bin from qr(805) - P(1400) Any 1 hue bin from G7(520)-Ga(540) Reel
Blue Any 1 Intensity bin from E(180) - G(355) Any 1 hue bin from B3(460)-B6(480) Reel
Notes:• The above kit numbers represent order codes that include multiple intensity-bin and color-bin codes. Only one intensity-bin code and one color-bin
code will be shipped on each bulk. Single intensity-bin code and single color-bin codes will not be orderable.
• Please refer to the HB LED Lamp Reliability Test Standards document for reliability test conditions.
• Please refer to the HB LED Lamp Soldering & Handling document for information about how to use this LED product safely.
• The CLY6C-FKC is rated as a MSL 5a product. • The recommended floor life out of bag is 24hrs. • The temperature profile is as below
Use only with CLX6C-FKC
Solder
Average ramp-up rate = 4ºC/s max
Preheat temperature = 150ºC ~200ºC
Preheat time = 120s max
Ramp-down rate = 6ºC/s max
Peak temperature = 235ºC max
Time within 5ºC of actual Peak Temperature = 10s max
Duration above 217ºC is 45s max
NOTES
• ThepackagingsizesoftheseSMDproductsareverysmallandtheresinisstillsoftaftersolidification.Usersarerequiredtohandlewithcare.Never touch the resin surface of SMD products.
• To avoid damaging the product’s surface and interior device, it is recommended to choose a special nozzle to pick up the SMD products during the process of SMT production. If handling is necessary, take special care when picking up these products. The following method is necessary:
Document No.: CREE-05-0057 Rev. NO. : 16
9/9
pick up SMD products during the process of SMT production . If handling is necessary, it should take more
careful to pick up these products. The following two methods are necessary :
Fig. 1a: For Small Top SMD Fig. 1b: For Mini side 0.8mm SMD
For Small Top SMD series , it is recommended to use rubber material Nozzle to pick up SMD products .Two
figure size for reference : a.) Circular Nozzle: inner diameter: Ø1.8mm+/-0.05mm, outer diameter: Ø2.3mm+/-0.05mm.
b.) Rectangle Nozzle: inner size: 1.3mm x 2.3mm, outer size > SMD size.
6. Electrostatic Discharge and Surge current Electrostatic discharge (ESD) or surge current (EOS) may damage SMD LED. Precautions such as ESD wrist strap, ESD shoe strap or antistatic gloves must be worn whenever handling of SMD LED. All devices, equipment and machinery must be properly grounded. It is recommended to perform electrical test to screen out ESD failures at final inspection. It is important to eliminate the possibility of surge current during circuitry design 7. Heat Management
Heat management of SMD LED must be taken into consideration during the design stage of SMD LED application. The current should be de-rated appropriately by referring to the de-rating curve attached on each product specification.
Data is subject to change without prior notice.
Document No.: COTCO-05-0057Rev. NO. : 13
6/9
Melting-point
Pre-heat Soak Reflow Cooling
Time
Tem
pera
ture
Use all SMD besides LP6-NPP1-01-N1Solder = Sn63-Pb37 Solder = Lead-free
Average ramp-up rate = 4ºC/s max. Average ramp-up rate = 4ºC/s max
Preheat temperature = 100ºC ~150ºC Preheat temperature = 150ºC ~200ºC
• The boxes are not water resistant and they must be kept away from water and moisture.• The LEDs are packed in cardboard boxes after packaging in normal or anti-electrostatic bags.• Cardboard boxes will be used to protect the LEDs from mechanical shocks during transportation.• The reel pack is applied in SMD LED.• Max 6500 pcs per reel.
C oba lt FreeC oba lt FreeC oba lt FreeC oba lt FreeAAAACCCC