switch -acceso-> un vlans -trunk->multi vilans. se usa las
vlans para saber que usuario quien es quien.
//configurando la interface vlan -- se configuro el switch en
modo accesoSwitch>enableSwitch#conf tEnter configuration
commands, one per line. End with CNTL/Z.Switch(config)#vlan
99Switch(config-vlan)#na% Incomplete
command.Switch(config-vlan)#naSwitch(config-vlan)#name
GestionSwitch(config-vlan)#exitSwitch(config)#int
f0/5Switch(config-if)#switchport modSwitch(config-if)#switchport
mode acSwitch(config-if)#switchport mode access
Switch(config-if)#swSwitch(config-if)#switchport
acSwitch(config-if)#switchport access
vlSwitch(config-if)#switchport access vlan 99Switch(config-if)#int
f0/6Switch(config-if)#swSwitch(config-if)#switchport
modSwitch(config-if)#switchport mode acSwitch(config-if)#switchport
mode accessSwitch(config-if)#Switch(config-if)#switchport
acSwitch(config-if)#switchport access
vlSwitch(config-if)#switchport access vlan
99-----------Switch(config-if)#Switch#%SYS-5-CONFIG_I: Configured
from console by console
Switch#enaSwitch#conf tEnter configuration commands, one per
line. End with CNTL/Z.Switch(config)#do sh runBuilding
configuration...
Current configuration : 1139 bytes!version 12.2no service
timestamps log datetime msecno service timestamps debug datetime
msecno service password-encryption!hostname Switch!!!!spanning-tree
mode pvst!interface FastEthernet0/1!interface
FastEthernet0/2!interface FastEthernet0/3!interface
FastEthernet0/4!interface FastEthernet0/5 switchport access vlan 99
switchport mode access!interface FastEthernet0/6 switchport access
vlan 99 switchport mode access!interface FastEthernet0/7!interface
FastEthernet0/8!interface FastEthernet0/9!interface
FastEthernet0/10!interface FastEthernet0/11!interface
FastEthernet0/12!interface FastEthernet0/13!interface
FastEthernet0/14!interface FastEthernet0/15!interface
FastEthernet0/16!interface FastEthernet0/17!interface
FastEthernet0/18!interface FastEthernet0/19!interface
FastEthernet0/20!interface FastEthernet0/21!interface
FastEthernet0/22!interface FastEthernet0/23!interface
FastEthernet0/24!interface GigabitEthernet1/1!interface
GigabitEthernet1/2!interface Vlan1 no ip address shutdown!!line con
0!line vty 0 4 login
Switch(config)#interface vlSwitch(config)#interface vlan
99Switch(config-if)#%LINK-5-CHANGED: Interface Vlan99, changed
state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan99, changed
state to up
Switch(config-if)#Switch(config-if)#Switch(config-if)#ip
adSwitch(config-if)#ip address 172.16.99.11% Incomplete
command.Switch(config-if)#ip address 172.16.99.11
255.255.255.0Switch(config-if)#
//configurando el routerContinue with configuration dialog?
[yes/no]: n
Press RETURN to get started!
Router>Router>Router>enableRouter#conf tEnter
configuration commands, one per line. End with
CNTL/Z.Router(config)#int g0/1Router(config-if)#ip add 172.16.99.1
255.255.255. ^% Invalid input detected at '^'
marker.Router(config-if)#ip add 172.16.99.1
255.255.255.0Router(config-if)#no shutRouter(config-if)#no
shutdown
Router(config-if)#%LINK-5-CHANGED: Interface GigabitEthernet0/1,
changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet0/1, changed state to up
Router(config-if)#exitRouter(config)#exitRouter#%SYS-5-CONFIG_I:
Configured from console by console
Router#ping 172.16.99.11
Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to
172.16.99.11, timeout is 2 seconds:..!!!Success rate is 60 percent
(3/5), round-trip min/avg/max = 0/0/0 ms
Router#
//para conectarse desde la pc via remota con el
switch-configurando el switchSwitch>enSwitch#conf tEnter
configuration commands, one per line. End with
CNTL/Z.Switch(config)#line vSwitch(config)#line vty 0
4Switch(config-line)#exitSwitch(config)#line vSwitch(config)#line
vty 0 ? Last Line number Switch(config)#line vty 0
4Switch(config-line)#pasSwitch(config-line)#password
ciscoSwitch(config-line)#loginSwitch(config-line)#------------- y
en la pc ponemos telnet y la direccion ip del switch---------
enable password cisco --> para entrar desde la pc en modo
privilegiado colocando ena ---- (Switch(config)#enable password
cisco)