Page 1
Cisco Nexus 3400-S Series NX-OS Command Reference (ConfigurationCommands), Release 9.2(2)First Published: 2019-07-03
Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000
800 553-NETS (6387)Fax: 408 527-0883
Page 2
© 2019 Cisco Systems, Inc. All rights reserved.
Page 3
C O N T E N T S
Preface cxliiiP R E F A C E
Audience cxliii
Documentation Conventions cxliii
Documentation Feedback cxliv
Communications, Services, and Additional Information cxliv
Notice 1C H A P T E R 1
Notice 2
A Commands 3C H A P T E R 2
aaa accounting default 8
aaa accounting dot1x default group 9
aaa authentication dot1x default group 10
aaa authentication login ascii-authentication 11
aaa authentication login console 12
aaa authentication login default 14
aaa authentication login default fallback error local 16
aaa authentication login enable 17
aaa authentication login error-enable 18
aaa authentication login invalid-username-log 19
aaa authentication login password-aging enable 20
aaa authentication rejected 21
aaa authentication rejected in ban 22
aaa authorization commands console 23
aaa authorization commands default 24
aaa authorization ssh default group 25
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)iii
Page 4
aaa bypass-user 26
aaa group server ldap 27
aaa group server radius 28
aaa group server tacacs 29
aaa test-authentication 30
aaa test-radius-authentication 31
aaa user default-role 32
abort 33
abort 34
abort 35
abort 36
absolute-timeout 37
absolute start 38
accept-lifetime month_a month_b month_c month_d month_e month_f month_g month_h month_imonth_j month_kmonth_l duration infinite month_a month_bmonth_c month_dmonth_e month_fmonth_g month_h month_i month_j month_k month_l 39
access-class 41
access-list 42
access-list 43
access-list ipv6 44
access vlan 45
acllog match-log-level 46
action 47
action 48
action cli 49
action counter name value op 50
action eem test 51
action event-default 52
action forceshut reset-reason 53
action overbudgetshut 54
action policy-default 55
action reload 56
action snmp-trap 57
action syslog msg 58
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)iv
Contents
Page 5
additional-paths install backup 59
additional-paths receive 60
additional-paths selection route-map 61
additional-paths send 62
address-family ipv4 63
address-family ipv4 labeled-unicast 64
address-family ipv4 labeled-unicast 65
address-family ipv4 mdt 66
address-family ipv4 mdt 67
address-family ipv4 mvpn 68
address-family ipv4 mvpn 69
address-family ipv6 70
address-family ipv6 labeled-unicast 71
address-family ipv6 labeled-unicast 72
address-family ipv6 mvpn 73
address-family ipv6 mvpn 74
address-family l2vpn evpn 75
address-family l2vpn evpn 76
address-family l2vpn vpls 77
address-family l2vpn vpls 78
address-family link-state 79
address-family link-state 80
address-family vpnv4 unicast 81
address-family vpnv4 unicast 82
address-family vpnv6 unicast 83
address-family vpnv6 unicast 84
address 85
address 86
address 87
address 88
address 89
address 90
address port-number 91
address primary 92
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)v
Contents
Page 6
address secondary 93
address secondary 94
adjacency-check 95
adjacency-resolve 96
advertise-gw-ip 97
advertise-labels 98
advertise-map exist default advertise-map 99
advertise-pip 100
advertise-system-mac 101
advertise evpn multicast 102
advertise interface 103
advertise l2vpn evpn 104
advertise local-labeled-route 105
advertise virtual-rmac 106
advertisement-interval 107
advertisement-interval 108
afd queue-desired 109
affinity-group 110
affinity-group activate 111
affinity 112
affinity 113
age 114
age 115
aggregate-address 116
aggregate-address 117
alert-group user-def-cmd 118
allocate-label all 119
allocate-label option-b 120
allocate1 interface2 121
allocate2 fcoe-vlan-range 122
allocate3 shared interface3 123
allow-vni-in-ethertag 124
allow feature-set 125
allowas-in 126
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)vi
Contents
Page 7
allowas-in 127
allowed-locators 128
allowed-vlans 129
amt flush-routes 130
amt pseudo-interface 131
analytics cluster 132
anonymous-id 133
append-after next 134
apply profile 135
area authentication 136
area authentication 137
area default-cost 138
area default-cost 139
area filter-list route-map in 140
area filter-list route-map in 141
area nssa 142
area nssa 143
area nssa translate type7 always never supress-fa 144
area nssa translate type7 always never supress-fa 145
area range 146
area range 147
area sham-link 148
area stub 149
area stub 150
area virtual-link 151
area virtual-link 152
area virtual-link 153
area virtual-link 154
arp access-list 155
as-format asdot 156
as-override 157
assign interface shared 158
assign vlan dedicated 159
assign vrf prefix number dedicated 160
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)vii
Contents
Page 8
attach console module 161
attach module 162
attach module node 163
attach module port 164
auth-mechanism plain 165
authentication-check 166
authentication-check 167
authentication-check level-1 168
authentication-check level-2 169
authentication-key 170
authentication-key 171
authentication-key 172
authentication-type cleartext 173
authentication-type cleartext 174
authentication-type cleartext 175
authentication 176
authentication 177
authentication 178
authentication 179
authentication 180
authentication 181
authentication bind 182
authentication challenge 183
authentication key-chain 184
authentication key-chain 185
authentication key-chain 186
authentication key-chain 187
authentication key-chain 188
authentication key-chain 189
authentication lifetime 190
authentication text 191
authentication type md5 192
authentication window-size 193
auto-bw 194
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)viii
Contents
Page 9
auto-bw 195
auto-bw timers frequency 196
auto-cost reference-bandwidth 197
auto-cost reference-bandwidth 198
auto-recovery 199
auto-remap-replication-servers 200
autonomous-system 201
autoroute announce 202
autoroute metric 203
autostate 204
autovlan enable 205
awk 206
B Commands 207C H A P T E R 3
backoff 210
backup-bw 211
bandwidth 212
bandwidth 213
bandwidth 214
bandwidth 215
bandwidth 216
bandwidth 217
bandwidth 218
bandwidth 219
bandwidth 220
bandwidth kbps mbps gbps 221
banner exec 222
banner motd 223
bcm-shell module 224
bcm-shell module 225
beacon 226
begin exclude include end 227
bestpath 228
bfd-app session auto-expiry timeout 229
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)ix
Contents
Page 10
bfd-app session remove 230
bfd-app session src-ip dest intf 231
bfd 232
bfd 233
bfd 234
bfd 235
bfd 236
bfd 237
bfd 238
bfd authentication interop 239
bfd authentication key-id key 240
bfd echo-interface 241
bfd echo-rx-interval 242
bfd echo 243
bfd interval 244
bfd interval 245
bfd interval min_rx multiplier 246
bfd interval min_rx multiplier 247
bfd move-session target 248
bfd multihop authentication key-id key bfd multihop authentication 249
bfd multihop hosting-linecard add module 250
bfd multihop hosting-linecard add module 251
bfd multihop interval 252
bfd multihop interval min_rx multiplier 253
bfd multihop interval min_rx multiplier 254
bfd neighbor src-ip dest 255
bfd optimize subinterface 256
bfd per-link 257
bfd session-store remove client 258
bfd session-store source-ip dest-ip intf client 259
bfd session state state 260
bfd slow-timer 261
bfd startup-timer bfd startup-timer 262
bfshell 263
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)x
Contents
Page 11
bfshell cmd 264
bfshell module 265
bfshell module cmd 266
binary-location 267
bind interface 268
bind mac-address 269
blink 270
bloggerd live-process-core sap 271
bloggerd log-dump all 272
bloggerd log-dump once log-buffer sap event-history 273
bloggerd log-dump once pss uuid 274
bloggerd log-throttle 275
bloggerd log-transfer 276
bloggerd log-transfer 277
bloggerd parse log-buffer file 278
bloggerd parse log-buffer file sap 279
bloggerd parse pss file 280
bmp-activate-server 281
bmp-server 282
boot-install nxos 283
boot-order 284
boot 285
boot aci 286
boot auto-copy 287
boot kickstart 288
boot mode docker_cluster 289
boot mode docker_standalone 290
boot mode lxc 291
boot nxos 292
boot nxos sup-1 293
boot nxos sup-1 sup-2 294
boot nxos sup-2 295
boot order bootflash 296
boot order pxe 297
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xi
Contents
Page 12
boot poap enable 298
boot system 299
bootmode boot 300
bootmode extruntime 301
bootmode hitless 302
bootmode module 303
bootmode nodiagruntime 304
bootmode runtime 305
buffer-boost 306
buffer-delete 307
buffer-move 308
burst-detect enable 309
burst-detect rise-threshold bytes fall-threshold bytes2 310
C Commands 311C H A P T E R 4
cabundle url 323
callhome 324
callhome send configuration 325
callhome send diagnostic 326
callhome test 327
callhome test inventory 328
capability additional-paths receive 329
capability additional-paths send 330
capability suppress 4-byte-as 331
capability vrf-lite 332
capture 333
capture 334
capture session 335
carrier-delay 336
catena 337
catena device-group 338
catena port-acl 339
catena port-group 340
catena vlan-group 341
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xii
Contents
Page 13
cbts-member tunnel-te 342
cd 343
cdp advertise v1 344
cdp enable 345
cdp enable 346
cdp format device-id 347
cdp holdtime 348
cdp timer 349
certificate 350
cfs debug all 351
cfs distribute 352
cfs eth cos 353
cfs eth distribute 354
cfs ipv4 distribute 355
cfs ipv6 distribute 356
cfs region 357
chain 358
change-password 359
channel-group 360
channel-group 361
channel-group 362
channel-group 363
channel-group force 364
channel-group force 365
channel mode 366
channel mode active 367
chassis-family fretta 368
checkpoint 369
checkpoint 370
cipher-suite 371
class-map 372
class-map type control-plane 373
class-map type network-qos 374
class-map type psp 375
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xiii
Contents
Page 14
class-map type queuing 376
class-map type queuing 377
class 378
class 379
class __inline__ 380
class class-default 381
class type network-qos 382
class type network-qos class-default 383
class type psp 384
class type queuing 385
clear 386
clear 387
clear 388
clear 389
clear aaa local user blocked username 390
clear access-list counters 391
clear access-list hardware counters 392
clear access-list ipsg stats 393
clear accounting log 394
clear aclqos cl-qos 395
clear aclqos fab 396
clear aclqos fc 397
clear aclqos libdrv 398
clear aclqos map 399
clear aclqos merge 400
clear aclqos pl 401
clear aclqos ppf-parse 402
clear aclqos ppf 403
clear aclqos qng-hw 404
clear aclqos qng 405
clear aclqos rl 406
clear aclqos rm 407
clear aclqos sch 408
clear aclqos stats 409
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xiv
Contents
Page 15
clear aclqos tbl 410
clear aclqos trace-detail 411
clear aclqos trace 412
clear aclqos uf 413
clear bfd statistics 414
clear bgp 415
clear bgp bmp stats server 417
clear bgp event-history 418
clear bgp private 419
clear bootvar log 421
clear cdp counters 422
clear checkpoint database 423
clear cli history 424
clear controller accounting log 425
clear copp statistics 426
clear cores 427
clear cores archive 428
clear counters 429
clear counters buffers 430
clear counters interface 431
clear counters interface 432
clear counters interface 433
clear counters interface all 434
clear counters interface snmp 435
clear counters tah-buffers 436
clear crypto ca trustpool timer 437
clear debug-logfile 438
clear debug logfile 439
clear dot1x all 440
clear dot1x stats interface 441
clear ecp statistics 442
clear eigrp event-history 443
clear evb hosts 444
clear evb hosts 445
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xv
Contents
Page 16
clear evb statistics 446
clear fabric database dci vrf node-id 447
clear fabric database host all vni 448
clear fabric database host statistics 449
clear fabric database include-vrf 450
clear fabric database statistics 451
clear fabric database statistics type server-proto radius group 452
clear fabric database statistics type server-proto xmpp ip 453
clear fabric multicast event-history 454
clear fc2 455
clear fctimer session 456
clear flow cache 457
clear flow cache 458
clear flow exporter 459
clear forwarding adjacency module 460
clear forwarding cumulative counter 461
clear forwarding distribution lisp counters all 462
clear forwarding events-history 463
clear forwarding inconsistency 464
clear forwarding ipv4 multicast counters 465
clear forwarding ipv6-l3-route-history 466
clear forwarding ipv6 adjacency module 467
clear forwarding ipv6 inconsistency 468
clear forwarding ipv6 multicast counters 469
clear forwarding ipv6 route module 470
clear forwarding l2-mc-route-history 471
clear forwarding l2-oiflist-history 472
clear forwarding l2-route-history 473
clear forwarding l2mcast info l2-mc-route-history 474
clear forwarding l2mcast info l2-oiflist-history 475
clear forwarding l2mcast info l2-route-history 476
clear forwarding l2mcast info l2-xbar-history 477
clear forwarding l2mcast info statistics 478
clear forwarding l2vpn trace member-history 479
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xvi
Contents
Page 17
clear forwarding l3-route-history 480
clear forwarding oiflist-history 481
clear forwarding route module 482
clear forwarding trace ecmp-history 483
clear forwarding trace mfib oif-history 484
clear forwarding trace mfib oiflist-history 485
clear forwarding trace mfib platform oiflist-history 486
clear forwarding trace mfib v4-route-history 487
clear forwarding trace mfib v6-route-history 488
clear forwarding trace v4-adj-history 489
clear forwarding trace v4-pfx-history 490
clear forwarding trace v4-rnh-history 491
clear forwarding trace v6-adj-history 492
clear forwarding trace v6-pfx-history 493
clear forwarding trace v6-rnh-history 494
clear forwarding trace vobj-history 495
clear frame traffic 496
clear fs-daemon log 497
clear hardware flow ip 498
clear hardware flow ipv6 499
clear hardware flow l2 500
clear hardware ip verify 501
clear hardware profile buffer monitor 503
clear hardware profile latency monitor 504
clear hardware profile packet-drop file_instance 505
clear hardware rate-limiter 506
clear hardware rate-limiter 507
clear hsrp counters clear hsrp state-history 508
clear install all failed-standby 509
clear install failure-reason 510
clear install log-history all 511
clear install status 512
clear ip 513
clear ip adjacency statistics 514
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xvii
Contents
Page 18
clear ip amt tunnel 515
clear ip arp 516
clear ip arp controller-statistics 517
clear ip arp inspection log 518
clear ip arp inspection statistics vlan 519
clear ip arp multihoming-statistics 520
clear ip arp statistics 521
clear ip arp suppression-cache statistics 522
clear ip arp tunnel-statistics 523
clear ip arp vpc-statistics 524
clear ip dhcp global statistics 525
clear ip dhcp relay statistics 526
clear ip dhcp snooping binding 527
clear ip dhcp snooping statistics 528
clear ip eigrp accounting 529
clear ip eigrp event-history 530
clear ip eigrp event-history bfd 531
clear ip eigrp redistribution 532
clear ip eigrp route-map statistics redistribute 533
clear ip eigrp traffic 534
clear ip igmp event-history 535
clear ip igmp groups 536
clear ip igmp interface statistics 537
clear ip igmp snooping event-history 538
clear ip igmp snooping explicit-tracking 539
clear ip igmp snooping groups 540
clear ip igmp snooping proxy querier ports vlan 541
clear ip igmp snooping report statistics 542
clear ip igmp snooping statistics 543
clear ip interface statistics 544
clear ip lisp data-cache 545
clear ip lisp map-cache 546
clear ip lisp statistics 547
clear ip mbgp dampening 548
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xviii
Contents
Page 19
clear ip mbgp flap-statistics 550
clear ip mbgp peer-template 552
clear ip mfwd event-history 554
clear ip mroute 555
clear ip mroute statistics 556
clear ip msdp event-history 557
clear ip msdp peer 558
clear ip msdp policy statistics sa-policy in 559
clear ip msdp sa 560
clear ip msdp statistics 561
clear ip nat-alias address 562
clear ip nat statistics 563
clear ip nat translation 564
clear ip ospf database 566
clear ip ospf event-history 567
clear ip ospf interface 568
clear ip ospf neighbor 569
clear ip ospf policy statistics 570
clear ip ospf redistribution 572
clear ip ospf statistics 573
clear ip ospf traffic 574
clear ip pim event-history 575
clear ip pim interface statistics 576
clear ip pim policy statistics 577
clear ip pim policy statistics jp 578
clear ip pim route 579
clear ip pim statistics 580
clear ip rip policy statistics redistribute bgp 581
clear ip rip statistics 582
clear ip routing multicast event-history 583
clear ip traffic 584
clear ipv6 adjacency statistics 585
clear ipv6 amt tunnel 586
clear ipv6 dhcp-ldra statistics 587
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xix
Contents
Page 20
clear ipv6 dhcp relay statistics 588
clear ipv6 eigrp route-map statistics redistribute 589
clear ipv6 icmp 590
clear ipv6 icmp vpc-statistics 591
clear ipv6 interface statistics 592
clear ipv6 lisp data-cache 593
clear ipv6 lisp statistics 594
clear ipv6 mld groups 595
clear ipv6 mroute 596
clear ipv6 neighbor 597
clear ipv6 neighbor binding 598
clear ipv6 pim event-history 599
clear ipv6 pim interface statistics 600
clear ipv6 pim policy statistics jp 601
clear ipv6 pim route 602
clear ipv6 pim statistics 603
clear ipv6 raguard statistics 604
clear ipv6 rip policy statistics redistribute bgp 605
clear ipv6 routing multicast event-history 606
clear ipv6 snooping counters 607
clear ipv6 snooping events 608
clear ipv6 snooping messages 609
clear ipv6 traffic 610
clear isis adjacency 611
clear isis dpi 612
clear isis event-history 613
clear isis ipv6 route-map statistics 614
clear isis redistribution 616
clear isis route-map statistics 617
clear isis spf-log 619
clear isis statistics 620
clear isis traffic 621
clear itd statistics 622
clear keystore 623
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xx
Contents
Page 21
clear l2dbg 624
clear l2fwder statistics 625
clear l3vm event-history 626
clear lacp counters 627
clear ldap-server statistics 628
clear license 630
clear lim counters 631
clear line 632
clear lisp ddt referral-cache 633
clear lisp dynamic-eid 634
clear lisp proxy-itr 635
clear lisp site 636
clear lldp counters 637
clear lldp counters interface 638
clear logging ip access-list cache 639
clear logging logfile 640
clear logging nvram 641
clear logging onboard 642
clear logging onboard 643
clear logging session 644
clear mac address-table datapath 645
clear mac address-table dynamic 646
clear mts message statistics 647
clear mvr counters 648
clear mvr counters receiver-ports 649
clear mvr counters source-ports 650
clear nbm flow statistics 651
clear ngoam 652
clear ngoam 653
clear ngoam 654
clear ngoam 655
clear ngoam pathtrace 656
clear ntp session 657
clear ntp statistics 658
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxi
Contents
Page 22
clear nvram 659
clear nxapi-server logs 660
clear openflow switch controller all 661
clear ospfv3 database 662
clear ospfv3 event-history 663
clear ospfv3 interface 664
clear ospfv3 neighbor 665
clear ospfv3 policy statistics 666
clear ospfv3 statistics 668
clear ospfv3 traffic 669
clear peer-info interface vsan 670
clear pktmgr client 671
clear pktmgr interface 672
clear plb analytics 673
clear port-security dynamic address vlan 674
clear port-security dynamic interface 675
clear processes log all 676
clear processes log all vdc-all 677
clear processes log archive 678
clear processes log pid 679
clear processes vdc log all 680
clear processes vdc log pid 681
clear ptp corrections 682
clear ptp counters interface 683
clear qos policies 684
clear qos policies force 685
clear qos statistics 686
clear queuing burst-detect 687
clear queuing pfc-queue 688
clear queuing pfc-queue interface 689
clear queuing tah-pfc-queue 690
clear radius-server statistics 691
clear radius session 693
clear rmon 694
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxii
Contents
Page 23
clear route-map pbr-statistics 695
clear routing event-history 696
clear routing ip multicast mfdm pending counters 697
clear routing ip multicast rpf-source retry-cache 698
clear routing ipv6 event-history 699
clear routing ipv6 multicast 700
clear routing multicast 701
clear scheduler logfile 702
clear screen 703
clear session state name 704
clear sflow statistics 705
clear snmp counters 706
clear snmp hostconfig 707
clear sockets statistics 708
clear spanning-tree counters 709
clear spanning-tree detected-protocols 710
clear spanning-tree sps-hist 711
clear ssh hosts 712
clear statistics module-all 713
clear statistics module 714
clear sup-monitor drops session 715
clear system login failures 716
clear system reset-reason 717
clear tacacs-server statistics 718
clear tech-support lock 720
clear tech-support lock 721
clear user 722
clear veobc counters 723
clear vlan access-list counters 724
clear vlan counters 725
clear vmtracker counters 726
clear vpc statistics all 727
clear vpc statistics peer-keepalive 728
clear vpc statistics vpc 729
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxiii
Contents
Page 24
clear vpc transport statistics 730
clear vrrp statistics 731
clear vrrpv3 event-history 732
clear vrrpv3 statistics 733
clear vtp counters 734
cli alias name 735
cli create new-cmd 736
cli var name 737
cli var name 738
cli var name 739
cli var name 740
cli verifynrun 741
client-to-client reflection 742
clis all 743
clock-tolerance ntp oneway absolute 744
clock format 12 745
clock format show-timezone debug 746
clock format show-timezone syslog 747
clock protocol 748
clock set 749
clock summer 751
clock sync-interval 752
cluster-id 753
collect 754
collect 755
collect 756
collect 757
collect 758
collect 759
collect counter bytes 760
collect ip version 761
collect timestamp sys-uptime first 762
collect transport tcp flags 763
color 764
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxiv
Contents
Page 25
commit 765
commit 766
commit 767
commit verbose 768
compress-bitfields ipv6 multicast 769
compress-bitfields ipv6 multicast 770
compress-bitfields multicast 771
conf-offset 772
confederation identifier 773
confederation peers 774
config-source controller 775
configure 776
configure config-template on substitute 777
configure maintenance profile normal 778
configure profile 779
configure replace 780
configure replace abort 781
configure replace commit 782
configure session 783
configure sync 784
congestion-control dctcp ecn-threshold bytes 785
congestion-control ecn 786
congestion-control random-detect 787
congestion-control random-detect forward-nonecn 788
congestion-control random-detect global-buffer minimum-threshold maximum-threshold 789
congestion-control tail-drop 790
connect 791
connected-prefix-sid-map 792
continue 793
contract-id 794
control-plane 795
control-plane dynamic 796
control vlan 797
control vlan 798
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxv
Contents
Page 26
controller-credentials username password 0 799
controller description 800
controller ip vrf 801
controller ipv4 802
controller ipv4 803
controller type l2 identifier 804
copp copy profile prefix 805
copp distributed-policing enable 806
copp profile 807
copp profile 808
copp rate-limit disable 809
copy 810
copy 812
copy licenses 813
copy licenses 814
copy recursive 815
copy running vdc-all 816
copy vdc-all 817
core-on-no-memory 818
core-on-no-memory 819
cost 820
count 821
count 822
counter name value op 823
crypto ca authenticate 824
crypto ca crl request 825
crypto ca enroll 826
crypto ca export pkcs12 827
crypto ca import certificate 828
crypto ca import pkcs12 829
crypto ca lookup 830
crypto ca remote ldap 831
crypto ca test verify 832
crypto ca trustpoint 833
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxvi
Contents
Page 27
crypto ca trustpool import url 834
crypto ca trustpool import url clean 835
crypto ca trustpool policy 836
crypto cert ssh-authorize 837
crypto certificatemap mapname 838
crypto key generate rsa 839
crypto key param rsa label modulus 840
crypto key zeroize rsa 841
cryptographic-algorithm 842
customer-id 843
cut 844
D Commands 845C H A P T E R 5
dampen-igp-metric 851
dampening 852
dampening 853
dampening 854
data-pattern 855
data-pattern pad 856
data-source 857
database-mapping 858
databits 859
databits 860
datapath-id 861
datapath-id 862
db-jid 863
db-security user password 864
db-table 865
dead-interval 866
dead-interval 867
dead-interval 868
deadtime 869
deadtime 870
deadtime 871
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxvii
Contents
Page 28
default-information originate 872
default-information originate 873
default-information originate 874
default-information originate 875
default-information originate 876
default-information originate 877
default-information originate always rd route-target 878
default-metric 879
default-metric 880
default-metric 881
default-metric 882
default-metric 883
default-miss 884
default-originate 885
default echo revision 886
default permit 887
default permit 888
default permit 889
define 890
delay-restore time 891
delay 892
delay 893
delay 894
delay peer-link 895
delay restore 896
delay restore interface-vlan 897
delay restore orphan-port 898
delay up 899
delete 900
delete ca-certificate 901
delete certificate 902
delete crl 903
demand-circuit 904
depth 905
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxviii
Contents
Page 29
depth 906
description 907
description 908
description 909
description 910
description 911
description 912
description 913
description 914
description 915
description 916
description 917
description 918
description 919
description 920
description 921
description 922
description 923
description 924
description 925
description 926
description 927
description 928
description 929
description 930
description 931
description 932
description 933
description 934
description 935
description 936
description 937
description 938
description 939
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxix
Contents
Page 30
description 940
description 941
description 942
description 943
description 944
description 945
description 946
description 947
description 948
description 949
description 950
description 951
description 952
description description 953
dest-ipaddr 954
dest-ipaddr 955
dest-port 956
dest 957
destination-group 958
destination-profile 959
destination-profile 960
destination-profile CiscoTAC-1 alert-group 961
destination-profile CiscoTAC-1 email-addr 962
destination-profile CiscoTAC-1 http 963
destination-profile CiscoTAC-1 message-level 964
destination-profile CiscoTAC-1 message-size 965
destination-profile CiscoTAC-1 transport-method http 966
destination-profile CiscoTAC-1 transport-method email 967
destination-profile alert-group 968
destination-profile email-addr 969
destination-profile format 970
destination-profile full-txt-destination alert-group 971
destination-profile full-txt-destination email-addr 972
destination-profile full-txt-destination http 973
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxx
Contents
Page 31
destination-profile full-txt-destination message-size 974
destination-profile full-txt-destination message-level 975
destination-profile full-txt-destination transport-method http 976
destination-profile full-txt-destination transport-method email 977
destination-profile http 978
destination-profile message-level 979
destination-profile message-size 980
destination-profile short-txt-destination alert-group 981
destination-profile short-txt-destination email-addr 982
destination-profile short-txt-destination http 983
destination-profile short-txt-destination message-size 984
destination-profile short-txt-destination message-level 985
destination-profile short-txt-destination transport-method http 986
destination-profile short-txt-destination transport-method email 987
destination-profile transport-method email 988
destination-profile transport-method http 989
destination-sup interface 990
destination 991
destination1 interface 992
destination 993
destination 994
destination 995
destination 996
destination 997
destination filter ip 998
destination filter ip any any 999
destination group 1000
destination interface 1001
destination ip 1002
device-group 1003
device-group 1004
device-role 1005
device-role 1006
device-role 1007
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxxi
Contents
Page 32
dfe-tuning-delay 1008
diagnostic bootup level 1009
diagnostic bootup level bypass 1010
diagnostic clear result module all diagnostic clear result module test 1011
diagnostic monitor interval module test all hour min second 1012
diagnostic monitor module test all 1013
diagnostic ondemand action-on-failure continue failure-count diagnostic ondemand action-on-failurestop 1014
diagnostic ondemand iteration 1015
diagnostic ondemand test-parameter module test port_lb packet-length 1016
diagnostic start module test 1017
diagnostic stop module test all 1018
diagnostic test simulation module test diagnostic test simulation module test clear 1019
diff-clean 1020
diff-clean all-users 1021
diff 1022
dir 1023
disable-connected-check 1024
disable-fka 1025
disable-peer-as-check 1026
disable-policy-batching 1027
disable 1028
discard-route external 1029
discard-route external 1030
discovery 1031
distance 1032
distance 1033
distance 1034
distance 1035
distance 1036
distance 1037
distance 1038
distribute into route-map all 1039
distribute link-state 1040
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxxii
Contents
Page 33
dns 1041
domain-id 1042
domain-id secondary 1043
domain-tag 1044
dont-capability-negotiate 1045
dos2nxos 1046
dot1q 1047
dot1q 1048
dot1q 1049
dot1q default dynamic 1050
dot1x default 1051
dot1x default 1052
dot1x host-mode 1053
dot1x initialize 1054
dot1x mac-auth-bypass 1055
dot1x mac-move 1056
dot1x max-reauth-req 1057
dot1x max-req 1058
dot1x pae 1059
dot1x port-control 1060
dot1x radius-accounting 1061
dot1x re-authenticate interface 1062
dot1x re-authentication 1063
dot1x re-authentication 1064
dot1x show credential 1065
dot1x start supplicant interface 1066
dot1x supplicant credential 1067
dot1x supplicant credential 1068
dot1x supplicant max-start 1069
dot1x supplicant max-start 1070
dot1x supplicant timeout auth-period 1071
dot1x supplicant timeout auth-period 1072
dot1x supplicant timeout held-period 1073
dot1x supplicant timeout held-period 1074
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxxiii
Contents
Page 34
dot1x supplicant timeout start-period 1075
dot1x supplicant timeout start-period 1076
dot1x system-auth-control 1077
dot1x timeout inactivity-period 1078
dot1x timeout inactivity-period 1079
dot1x timeout quiet-period 1080
dot1x timeout quiet-period 1081
dot1x timeout ratelimit-period 1082
dot1x timeout re-authperiod 1083
dot1x timeout re-authperiod 1084
dot1x timeout server-timeout 1085
dot1x timeout supp-timeout 1086
dot1x timeout tx-period 1087
dot1x timeout tx-period 1088
down-bit-ignore 1089
downlink delay 1090
dpp set-qos-group 1091
drop-trigger 1092
droplist 1093
droplist 1094
dscp 1095
dscp 1096
dscp 1097
dscp 1098
dscp 1099
dscp 1100
dst-grp 1101
dual-active exclude interface-vlan 1102
duplex 1103
duplex 1104
duplicate-message throttle 1105
dynamic-capability 1106
dynamic-med-interval 1107
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxxiv
Contents
Page 35
E Commands 1109C H A P T E R 6
eapol mac-address 1116
ebgp-multihop 1117
echo 1118
echo 1119
ecp max-retries 1120
ecp mode lan 1121
ecp retransmission-timer-exponent 1122
eem test 1123
eemtest policy-add 1124
eemtest policy-remove 1125
egress-engineering 1126
egress 1127
eid-prefix 1128
eigrp event-history cli size 1129
eigrp file-debug 1130
email-addr 1131
email-contact 1132
email 1133
email 1134
enable 1135
enable 1136
enable Cert 1137
encapsulation dot1q 1138
encapsulation dot1q 1139
encrypt pause-frame 1140
encryption decrypt type6 1141
encryption delete type6 1142
encryption re-encrypt obfuscated 1143
end 1144
endpoint 1145
enforce-first-as 1146
enrollment terminal 1147
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxxv
Contents
Page 36
errdisable 1148
errdisable detect cause 1149
errdisable detect cause acl-exception 1150
errdisable port detect cause acl-exception 1151
errdisable recovery interval 1152
erspan-id 1153
ethanalyzer local 1154
ethernet-segment 1155
ethernet-segment delay-restore time 1156
ethernet-tag encapsulation dot1q default static 1157
ethernet-tag encapsulation dot1q static 1158
ethernet-tag encapsulation vni default static 1159
ethernet-tag encapsulation vni static 1160
evb mac 1161
evb reinit-keep-alive 1162
evb resource-wait-delay 1163
event-history 1164
event-history acllog category all 1165
event-history acllog category all 1166
event-history acllog category fc2 1167
event-history acllog category fc2 1168
event-history acllog category mts 1169
event-history acllog category mts 1170
event-history adbm category all 1171
event-history adbm category all 1172
event-history adbm category fc2 1173
event-history adbm category fc2 1174
event-history adbm category mts 1175
event-history adbm category mts 1176
event-history callhome 1177
event-history capability 1178
event-history cli 1179
event-history copp category all 1180
event-history copp category all 1181
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxxvi
Contents
Page 37
event-history copp category fc2 1182
event-history copp category fc2 1183
event-history copp category mts 1184
event-history copp category mts 1185
event-history dot1x 1186
event-history drap category all 1187
event-history drap category all 1188
event-history drap category mts 1189
event-history drap category mts 1190
event-history eltm category all 1191
event-history eltm category all 1192
event-history eltm category fc2 1193
event-history eltm category fc2 1194
event-history eltm category mts 1195
event-history eltm category mts 1196
event-history epp category all 1197
event-history epp category all 1198
event-history epp category fc2 1199
event-history epp category fc2 1200
event-history epp category mts 1201
event-history epp category mts 1202
event-history errors 1203
event-history ethpm 1204
event-history events 1205
event-history exceptionlog 1206
event-history fcoe_mgr category all 1208
event-history fcoe_mgr category all 1209
event-history fcoe_mgr category fc2 1210
event-history fcoe_mgr category fc2 1211
event-history fcoe_mgr category mts 1212
event-history fcoe_mgr category mts 1213
event-history hardware-telemetry 1214
event-history im category mts 1215
event-history imp category all 1216
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxxvii
Contents
Page 38
event-history imp category all 1217
event-history imp category fc2 1218
event-history imp category fc2 1219
event-history imp category mts 1220
event-history imp category mts 1221
event-history keystore 1222
event-history lacp category all 1223
event-history lacp category all 1224
event-history lacp category fc2 1225
event-history lacp category fc2 1226
event-history lacp category mts 1227
event-history lacp category mts 1228
event-history lem-mgr category all 1229
event-history lem-mgr category all 1230
event-history lem-mgr category fc2 1231
event-history lem-mgr category fc2 1232
event-history lem-mgr category mts 1233
event-history lem-mgr category mts 1234
event-history license 1235
event-history lldp category all 1236
event-history lldp category all 1237
event-history lldp category fc2 1238
event-history lldp category fc2 1239
event-history lldp category mts 1240
event-history lldp category mts 1241
event-history m2rib category all 1242
event-history mfdm category all 1243
event-history mfdm category all 1244
event-history mfdm category fc2 1245
event-history mfdm category fc2 1246
event-history mfdm category mts 1247
event-history mfdm category mts 1248
event-history mmode category all 1249
event-history module 1250
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxxviii
Contents
Page 39
event-history npv category all 1251
event-history npv category all 1252
event-history npv category fc2 1253
event-history npv category fc2 1254
event-history npv category mts 1255
event-history npv category mts 1256
event-history pfstat category all 1257
event-history pfstat category all 1258
event-history pfstat category fc2 1259
event-history pfstat category fc2 1260
event-history pfstat category mts 1261
event-history pfstat category mts 1262
event-history platform buffer-size 1263
event-history platform category all 1264
event-history platform category all 1265
event-history pltfm_config category all 1266
event-history pltfm_config category all 1267
event-history pltfm_config category fc2 1268
event-history pltfm_config category fc2 1269
event-history pltfm_config category mts 1270
event-history pltfm_config category mts 1271
event-history plugin 1272
event-history poap category all 1273
event-history poap category all 1274
event-history poap category fc2 1275
event-history poap category fc2 1276
event-history poap category mts 1277
event-history poap category mts 1278
event-history port-profile category all 1279
event-history port-profile category mts 1280
event-history port-resources category all 1281
event-history port-resources category all 1282
event-history port-resources category fc2 1283
event-history port-resources category fc2 1284
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xxxix
Contents
Page 40
event-history port-resources category mts 1285
event-history port-resources category mts 1286
event-history port-security category all 1287
event-history port-security category all 1288
event-history port-security category fc2 1289
event-history port-security category fc2 1290
event-history port-security category mts 1291
event-history port-security category mts 1292
event-history port category fc2 1293
event-history port category fc2 1294
event-history port category mts 1295
event-history port category mts 1296
event-history port_client category all 1297
event-history port_client category all 1298
event-history port_client category fc2 1299
event-history port_client category fc2 1300
event-history port_client category mts 1301
event-history port_client category mts 1302
event-history san-port-channel category all 1303
event-history san-port-channel category all 1304
event-history san-port-channel category fc2 1305
event-history san-port-channel category fc2 1306
event-history san-port-channel category mts 1307
event-history san-port-channel category mts 1308
event-history sensor 1309
event-history session-mgr category all 1310
event-history session-mgr category all 1311
event-history session-mgr category mts 1312
event-history session-mgr category mts 1313
event-history sflow 1314
event-history snmp 1315
event-history spanning-tree category all 1316
event-history spm category all 1317
event-history spm category all 1318
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xl
Contents
Page 41
event-history spm category fc2 1319
event-history spm category fc2 1320
event-history spm category mts 1321
event-history spm category mts 1322
event-history stripcl category all 1323
event-history stripcl category all 1324
event-history stripcl category mts 1325
event-history tamnw category all 1326
event-history tamnw category all 1327
event-history tamnw category fc2 1328
event-history tamnw category fc2 1329
event-history tamnw category mts 1330
event-history tamnw category mts 1331
event-history udld category all 1332
event-history ufdm category all 1333
event-history ufdm category all 1334
event-history ufdm category fc2 1335
event-history ufdm category fc2 1336
event-history ufdm category mts 1337
event-history ufdm category mts 1338
event-history vdc category all 1339
event-history vdc category all 1340
event-history vdc category mts 1341
event-history xbar category all 1342
event-history xbar category all 1343
event-history xbar category debug 1344
event-history xbar category debug 1345
event-history xbar category mts 1346
event-history xbar category mts 1347
event-log-size 1348
event-logging 1349
event 1350
event 1351
event application sub-system type 1352
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xli
Contents
Page 42
event cli match 1353
event counter name entry-val entry-op 1354
event fanabsent time 1355
event fanbad time 1356
event fib adjacency extra 1357
event fib resource tcam usage 1358
event fib route 1359
event gold module test testing-type scheduled consecutive-failure 1360
event manager applet 1361
event manager clear counter 1362
event manager clear history events 1363
event manager environment 1364
event manager policy 1365
event manager run 1366
event memory 1367
event module-failure type module count 1368
event module status module1 1369
event neighbor-discovery 1370
event none 1371
event oir fan 1372
event oir module 1373
event oir powersupply 1374
event policy-default count 1375
event poweroverbudget 1376
event snmp oid get-type exact entry-op entry-val poll-interval 1377
event storm-control 1379
event syslog pattern 1380
event sysmgr memory major minor clear 1381
event sysmgr switchover count time 1382
event temperature threshold 1383
event test match 1384
event timer 1385
event track state 1386
evpn 1387
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xlii
Contents
Page 43
evpn esi multihoming 1388
evpn multihoming core-tracking 1389
evpn multisite border-gateway 1390
evpn multisite dci-tracking 1391
evpn multisite fabric-tracking 1392
evpn storm-control level 1393
exceptionlog module syserr devid errtype errcode phylayer ports harderror 1394
exclude access-list 1395
exclude access-list 1396
exec-timeout 1397
exec-timeout 1398
existing-cli 1399
exit 1400
exit 1401
exp 1402
explicit-null 1403
explicit-path 1404
explicit-path identifier 1405
export-gateway-ip 1406
export map 1407
export vrf default map 1408
exporter-id 1409
exporter 1410
exporter 1411
exporter 1412
exporter 1413
exporter 1414
F Commands 1415C H A P T E R 7
fabric-soo 1420
fabric database auto-pull dci node-id 1421
fabric database auto-pull dci vrf node-id 1422
fabric database auto-pull vni interface 1423
fabric database inherit-profile-map 1424
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xliii
Contents
Page 44
fabric database mobility-domain 1425
fabric database override-profile 1426
fabric database override-vrf-profile 1427
fabric database profile-map 1428
fabric database profile-map global 1429
fabric database refresh dot1q 1430
fabric database refresh vni 1431
fabric database static-host 1432
fabric database timer 1433
fabric database type bl-dci 1434
fabric database type cabling 1435
fabric database type host 1436
fabric database type network 1437
fabric database type partition 1438
fabric database type profile 1439
fabric forwarding admin-distance 1440
fabric forwarding anycast-gateway-mac 1441
fabric forwarding dup-host-ip-addr-detection 1442
fabric forwarding dup-host-recovery-timer recover-count 1443
fabric forwarding dup-host-unfreeze-timer unfreeze-count 1444
fabric forwarding limit-vlan-mac 1445
fabric forwarding mode anycast-gateway 1446
fabric forwarding selective-host-probe 1447
fabric multicast event-history bgp 1448
fabric multicast event-history ha 1449
fabric multicast event-history hmm 1450
fabric multicast event-history isis 1451
fabric multicast event-history m2rib 1452
fabric multicast event-history m6rib 1453
fabric multicast event-history mrib 1454
fabric multicast event-history pim 1455
fabric multicast event-history pim6 1456
failaction 1457
failaction 1458
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xliv
Contents
Page 45
fast-convergence 1459
fast-convergence 1460
fast-external-fallover 1461
fast-flood enable 1462
fast-flood enable 1463
fast-flood enable 1464
fast-flood interval 1465
fast-flood interval 1466
fast-flood interval 1467
fast-reload 1468
fast-reload network-os 1469
fast-reroute 1470
fast-reroute backup-prot-preempt optimize-bw 1471
fcdroplatency network 1472
fcoe 1473
fcoe 1474
fcoe enable-fex 1475
fcoe fcf-priority 1476
fcoe fcmap 1477
fcoe fka-adv-period 1478
fcoe veloopback 1479
fcoe vsan 1480
fctimer D_S_TOV 1481
fctimer E_D_TOV 1482
fctimer R_A_TOV 1483
fctimer abort 1484
fctimer commit 1485
fctimer distribute 1486
feature-set 1487
feature-set 1488
feature 1489
feature analytics 1490
feature bash-shell 1491
feature bfd 1492
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xlv
Contents
Page 46
feature bgp 1493
feature catena 1494
feature container-tracker 1495
feature dhcp 1496
feature dot1x 1497
feature eigrp 1498
feature evb 1499
feature evmed 1500
feature fabric forwarding 1501
feature flexlink 1502
feature grpc 1503
feature hardware-telemetry 1504
feature hsrp 1505
feature icam 1506
feature imp 1507
feature interface-vlan 1508
feature isis 1509
feature itd 1510
feature lacp 1511
feature ldap 1512
feature lldp 1513
feature msdp 1514
feature mvpn 1515
feature nat 1516
feature nbm 1517
feature netconf 1518
feature ngmvpn 1519
feature ngoam 1520
feature ngoam 1521
feature npiv 1522
feature ntp 1523
feature nv overlay 1524
feature nxapi 1525
feature nxdb 1526
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xlvi
Contents
Page 47
feature nxsdk 1527
feature openflow 1528
feature openflow 1529
feature ospf 1530
feature ospfv3 1531
feature password encryption aes 1532
feature pbr 1533
feature pim 1534
feature pim6 1535
feature plb 1536
feature poap 1537
feature poe 1538
feature pong 1539
feature port-security 1540
feature private-vlan 1541
feature privilege 1542
feature ptp 1543
feature restconf 1544
feature rip 1545
feature scheduler 1546
feature scp-server 1547
feature sflow 1548
feature sftp-server 1549
feature signature-verification 1550
feature sla responder 1551
feature sla sender 1552
feature sla twamp-server 1553
feature smart-channel 1554
feature ssh 1555
feature tacacs 1556
feature telnet 1557
feature tunnel 1558
feature udld 1559
feature vmtracker 1560
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xlvii
Contents
Page 48
feature vn-segment-vlan-based 1561
feature vpc 1562
feature vrrp 1563
feature vrrpv3 1564
feature vtp 1565
fec 1566
fec 1567
fec 1568
fhrp delay minimum 1569
fhrp delay reload 1570
filter 1571
filter access-group 1572
filter ip 1573
filter ipv6 access-group 1574
filter out 1575
filter tx control-packets 1576
filter vlan 1577
filter vlan include-untagged 1578
find 1579
fips debug errors debug 1580
fips mode enable 1581
flow-count 1582
flow-count 1583
flow exporter 1584
flow forward 1585
flow monitor 1586
flow record 1587
flow timeout 1588
flowcontrol hardware 1589
flowcontrol receive 1590
flush-routes 1591
flush-routes 1592
flush-routes 1593
flush-routes 1594
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xlviii
Contents
Page 49
flush-routes 1595
flush-routes 1596
follow 1597
format 1598
format bootflash 1599
format bootflash check-filesystem 1600
format usb1 1601
forward 1602
forwarding-adjacency 1603
fragments 1604
frequency 1605
from to 1606
from to 1607
fte event 1608
fte exporter 1609
fte monitor 1610
fte record 1611
fte system monitor 1612
ftrace 1613
G Commands 1615C H A P T E R 8
generate type7_encrypted_secret 1616
getnext 1617
global-block 1618
global ingress-replication protocol bgp 1619
global suppress-arp 1620
graceful-restart-helper 1621
graceful-restart 1622
graceful-restart 1623
graceful-restart 1624
graceful-restart 1625
graceful-restart 1626
graceful-restart 1627
graceful-restart 1628
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xlix
Contents
Page 50
graceful-restart 1629
graceful-restart grace-period 1630
graceful-restart grace-period 1631
graceful-restart helper-disable 1632
graceful-restart helper-disable 1633
graceful-restart restart-time 1634
graceful-restart stalepath-time 1635
graceful-restart t3 manual 1636
graceful-restart t3 manual 1637
graceful-restart t3 manual 1638
graceful consistency-check 1639
grep 1640
grep 1641
grep 1642
group drop-events 1643
group latency-events 1644
guestshell 1645
gunzip 1646
gzip 1647
H Commands 1649C H A P T E R 9
ha-policy single 1652
hardware-telemetry fte 1653
hardware-telemetry inband-telemetry 1654
hardware-telemetry postcard-telemetry 1655
hardware-telemetry ssx 1656
hardware access-list lou resource threshold 1657
hardware access-list match inner-header 1658
hardware access-list module 1659
hardware access-list tcam label ing-racl 9 1660
hardware access-list tcam region 1661
hardware access-list tcam region double-wide 1662
hardware access-list tcam region qualify udf 1663
hardware access-list tcam region tcp-nat 1664
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)l
Contents
Page 51
hardware ecmp hash-offset 1665
hardware ecmp hash-polynomial 1666
hardware ejector enable 1667
hardware fan-zone raise-speed 1668
hardware forwarding l3 resource route non-deterministic 1669
hardware forwarding unicast trace 1670
hardware ip glean throttle 1671
hardware ip glean throttle maximum 1672
hardware ip glean throttle syslog 1673
hardware ip glean throttle timeout 1674
hardware ipv6 glean throttle 1675
hardware ipv6 glean throttle maximum 1676
hardware ipv6 glean throttle syslog 1677
hardware ipv6 glean throttle timeout 1678
hardware module boot-order reverse 1679
hardware multicast global-tx-span 1680
hardware profile buffer info poll-interval timer 1681
hardware profile buffer info port-threshold threshold 1682
hardware profile buffer monitor unicast 1683
hardware profile buffer qosgroup threshold 1684
hardware profile buffer span-threshold 1685
hardware profile ecmp auto-recovery threshold 1686
hardware profile ecmp resilient 1687
hardware profile ecmp template module 1688
hardware profile forwarding-mode 1689
hardware profile front portmode 1690
hardware profile ipv6 alpm carve-value 1691
hardware profile ipv6 lpm-entries maximum 1692
hardware profile latency monitor 1693
hardware profile module 1694
hardware profile multicast flex-stats-enable 1695
hardware profile multicast max-limit 1696
hardware profile multicast max-limit lpm-entries 1697
hardware profile multicast nlb 1698
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)li
Contents
Page 52
hardware profile multicast optimization disable 1699
hardware profile multicast prefer-source-tree 1700
hardware profile multicast rpf-check-optimization 1701
hardware profile multicast service-reflect port 1702
hardware profile multicast slow-receiver port 1703
hardware profile multicast syslog-threshold 1704
hardware profile openflow 1705
hardware profile packet-drop 1706
hardware profile pbr skip-selfip 1707
hardware profile pfc mmu buffer-reservation 1708
hardware profile portmode 1709
hardware profile statistics pstat 1710
hardware profile svi flex-stats-enable 1711
hardware profile tcam ipv6-sup-tcam match-inner 1712
hardware profile tcam region 1713
hardware profile tcam region span qualify udf 1714
hardware profile tcam region spanv6-l2 qualify udf 1715
hardware profile tcam region spanv6 qualify udf 1716
hardware profile tcam resource service-template 1717
hardware profile tcam resource template 1718
hardware profile tcam syslog-threshold 1719
hardware profile ucast6 lpm-65-to-127-max-limit 1720
hardware profile ucast6 max-limit 1721
hardware profile unicast enable-host-ecmp 1722
hardware profile unicast syslog-threshold 1723
hardware qos dynamic-buffer-sharing 1724
hardware qos fc rate-shaper 1725
hardware qos pfc mc-drop 1726
hardware sample-redirect module redirect-interface 1727
head 1728
header-type 2 1729
hello-interval 1730
hello-interval 1731
hello-interval 1732
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lii
Contents
Page 53
history 1733
history 1734
history 1735
history 1736
history 1737
history 1738
holdtime 1739
hop-limit maximum 1740
hop-limit minimum 1741
hop 1742
host-reachability protocol 1743
host 1744
host group permit 1745
host source group permit 1746
hostname 1747
hostname dynamic 1748
hostname dynamic 1749
hostname dynamic 1750
hsrp 1751
hsrp anycast 1752
hsrp bfd 1753
hsrp bfd all-interfaces 1754
hsrp delay minimum 1755
hsrp force state vlan 1756
hsrp ipv6 1757
hsrp mac-refresh 1758
hsrp timers extended-hold 1759
hsrp use-bia 1760
hsrp version 1 1761
http get 1762
http proxy server 1763
human 1764
human 1765
hw-module logging onboard 1766
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)liii
Contents
Page 54
hw-module logging onboard 1767
I Commands 1769C H A P T E R 1 0
icam monitor entries acl module inst 1786
icam monitor interval num_intervals 1787
icam monitor resource acl_tcam module inst 1788
icam monitor scale 1789
icam monitor scale 1791
icmp-echo 1792
icmpv6 cfs-queue 1793
icmpv6 library mts-queue 1794
icmpv6 mts-queue 1795
import 1796
import interface 1797
import l2vpn evpn 1798
import map 1799
import running-config 1800
import vpn unicast 1801
import vrf default map 1802
in-label allocate 1803
inband-telemetry exporter 1804
inband-telemetry flow-profile 1805
inband-telemetry monitor 1806
inband-telemetry queue-profile 1807
inband-telemetry record 1808
inband-telemetry system monitor 1809
inband-telemetry watchlist ip 1810
include-icv-indicator 1811
include profile 1812
include profile any 1813
index next-label 1814
index next 1815
ingress-mtu 1816
ingress-replication protocol bgp 1817
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)liv
Contents
Page 55
ingress-replication protocol static 1818
ingress 1819
ingress interface 1820
ingress interface 1821
inherit peer-policy 1822
inherit peer-policy 1823
inherit peer-session 1824
inherit peer 1825
inherit port-profile 1826
initial-delay 1827
initial-refresh skip 1828
inject-map exist-map 1829
innoshell 1830
innoshell cmd 1831
innoshell module 1832
innoshell module cmd 1833
install activate 1834
install add 1835
install all 1836
install all network-os 1837
install commit 1838
install deactivate 1839
install epld 1840
install epld 1841
install feature-set fcoe-npv 1842
install license 1843
install license 1844
install remove 1845
install reset 1846
install verify 1847
instance-id 1848
instance 1849
instance 1850
instance vlan 1851
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lv
Contents
Page 56
interface 1852
interface 1853
interface 1854
interface 1855
interface 1856
interface 1857
interface 1858
interface 1859
interface 1860
interface 1861
interface 1862
interface 1863
interface 1864
interface 1865
interface 1866
interface 1867
interface 1868
interface breakout-profile 1869
interface breakout module 1870
interface breakout module 1871
interface breakout module port map 1872
interface breakout module port map 1873
interface down delay 1874
interop-enable 1875
interval 1876
interval 1877
ip 1878
ip 1879
ip 1880
ip 1881
ip 1882
ip 1883
ip 1884
ip access-class 1885
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lvi
Contents
Page 57
ip access-group 1886
ip access-list 1887
ip access-list match-local-traffic 1888
ip address 1889
ip address dhcp 1890
ip address ipv6 address port 1891
ip address secondary 1892
ip adjacency peer-gmac 1893
ip adjacency remote-adj 1894
ip adjacency route distance 1895
ip amt anycast-relay-prefix 1896
ip amt gateway 1897
ip amt join-policy 1898
ip amt qqic 1899
ip amt relay-advertisement-address 1900
ip amt relay 1901
ip amt state-limit 1902
ip amt tunnel-limit 1903
ip arp 1904
ip arp allow-static-arp-outside-subnet 1905
ip arp cache limit 1906
ip arp cos 1907
ip arp delete 1908
ip arp event-history size 1909
ip arp event-history size 1911
ip arp evpn timeout 1913
ip arp gratuitous hsrp duplicate 1914
ip arp gratuitous request 1915
ip arp gratuitous update 1916
ip arp inspection filter vlan 1917
ip arp inspection log-buffer entries 1918
ip arp inspection trust 1919
ip arp inspection validate 1920
ip arp inspection vlan 1921
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lvii
Contents
Page 58
ip arp off-list timeout 1922
ip arp rarp fabric-forwarding 1923
ip arp rarp fabric-forwarding 1924
ip arp rarp fabric-forwarding rate-limit 1925
ip arp suppression-cache 1926
ip arp suppression timeout 1927
ip arp synchronize 1928
ip arp timeout 1929
ip arp timeout 1930
ip arp unnum-svi-dup-ip-detection 1931
ip arp unnum-svi-sw-replication 1932
ip as-path access-list deny 1933
ip as-path access-list deny 1934
ip as-path access-list seq deny 1935
ip authentication 1936
ip auto-discard 1937
ip bandwidth-percent eigrp 1938
ip bandwidth eigrp 1939
ip community-list expanded deny 1940
ip community-list expanded deny 1941
ip community-list expanded seq deny 1942
ip community-list standard permit internet local-AS 1943
ip community-list standard permit internet local-AS 1944
ip community-list standard seq permit internet local-AS 1945
ip delay eigrp 1946
ip destination 1947
ip dhcp option82 suboption circuit-id 1948
ip dhcp packet strict-validation 1949
ip dhcp relay 1950
ip dhcp relay address 1951
ip dhcp relay information option 1952
ip dhcp relay information option trust 1953
ip dhcp relay information option vpn 1954
ip dhcp relay information trust-all 1955
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lviii
Contents
Page 59
ip dhcp relay information trusted 1956
ip dhcp relay source-interface 1957
ip dhcp relay source-interface 1958
ip dhcp relay sub-option circuit-id customized 1959
ip dhcp relay sub-option circuit-id format-type string 1960
ip dhcp relay sub-option type cisco 1961
ip dhcp smart-relay 1962
ip dhcp smart-relay global 1963
ip dhcp snooping 1964
ip dhcp snooping information option 1965
ip dhcp snooping ipsg-excluded vlan 1966
ip dhcp snooping sub-option circuit-id format-type string 1967
ip dhcp snooping trust 1968
ip dhcp snooping verify mac-address 1969
ip dhcp snooping vlan 1970
ip directed-broadcast 1971
ip distribute-list eigrp 1972
ip dns source-interface 1973
ip domain-list 1974
ip domain-lookup 1975
ip domain-name 1976
ip drop-glean 1977
ip dscp-lop 1978
ip dscp 1979
ip eigrp bfd 1980
ip eigrp event-history bfd size 1981
ip eigrp event-history errors 1982
ip eigrp event-history size 1983
ip eigrp shutdown 1984
ip extcommunity-list expanded deny 1985
ip extcommunity-list standard permit 1986
ip fabric multicast file-debug 1987
ip flow monitor input 1988
ip flow monitor input 1989
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lix
Contents
Page 60
ip flow monitor input 1990
ip forward 1991
ip ftp source-interface 1992
ip hello-interval eigrp 1993
ip hold-time eigrp 1994
ip host 1995
ip host host 1996
ip http source-interface 1997
ip icmp-errors source-interface 1998
ip igmp any-query-destination 1999
ip igmp enforce-router-alert 2000
ip igmp event-history cli 2001
ip igmp event-history ha 2002
ip igmp event-history interface 2003
ip igmp event-history interface 2004
ip igmp event-history mtrace 2005
ip igmp event-history mvr 2006
ip igmp event-history nbm 2007
ip igmp event-history policy 2008
ip igmp event-history vrf 2009
ip igmp file-debug 2010
ip igmp flush-routes 2011
ip igmp group-timeout 2012
ip igmp heavy-template 2013
ip igmp host-proxy 2014
ip igmp immediate-leave 2015
ip igmp join-group 2016
ip igmp last-member-query-count 2017
ip igmp last-member-query-response-time 2018
ip igmp querier-elect strict 2019
ip igmp querier 2020
ip igmp query-interval 2021
ip igmp query-max-response-time 2022
ip igmp report-link-local-groups 2023
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lx
Contents
Page 61
ip igmp report prefix-list 2024
ip igmp robustness-variable 2025
ip igmp snooping 2026
ip igmp snooping 2027
ip igmp snooping 2028
ip igmp snooping access-group 2029
ip igmp snooping disable-nve-static-router-port 2030
ip igmp snooping disable-nve-static-router-port 2031
ip igmp snooping event-history igmp-snoop-internal 2032
ip igmp snooping event-history mfdm-sum 2033
ip igmp snooping event-history mfdm 2034
ip igmp snooping event-history rib 2035
ip igmp snooping event-history vlan-events 2036
ip igmp snooping event-history vlan 2037
ip igmp snooping event-history vpc 2038
ip igmp snooping group-timeout 2039
ip igmp snooping group-timeout 2040
ip igmp snooping last-member-query-interval 2041
ip igmp snooping link-local-groups-suppression 2042
ip igmp snooping link-local-groups-suppression 2043
ip igmp snooping many-to-one-enhance 2044
ip igmp snooping max-gq-miss 2045
ip igmp snooping mrouter vpc-peer-link 2046
ip igmp snooping proxy-leave use-group-address 2047
ip igmp snooping proxy general-queries 2048
ip igmp snooping proxy general-queries 2049
ip igmp snooping report-flood all 2050
ip igmp snooping report-suppression 2051
ip igmp snooping report-suppression 2052
ip igmp snooping report prefix interface 2053
ip igmp snooping syslog-threshold 2054
ip igmp snooping v3-report-suppression 2055
ip igmp snooping v3-report-suppression 2056
ip igmp spoof-check 2057
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxi
Contents
Page 62
ip igmp ssm-translate 2058
ip igmp startup-query-count 2059
ip igmp startup-query-interval 2060
ip igmp state-limit 2061
ip igmp static 2062
ip igmp suppress v3-gsq 2063
ip igmp syslog-threshold 2064
ip igmp version 2065
ip lisp alt-vrf 2066
ip lisp database-mapping dynamic priority weight 2067
ip lisp disable-spoof-alert 2068
ip lisp etr 2069
ip lisp etr accept-map-request-mapping 2070
ip lisp etr glean-mapping 2071
ip lisp etr map-cache-ttl 2072
ip lisp etr map-register-ttl 2073
ip lisp etr map-server key 2074
ip lisp hardware-forwarding 2075
ip lisp itr-etr 2076
ip lisp itr 2077
ip lisp itr map-resolver 2078
ip lisp itr send-data-probe 2079
ip lisp locator-vrf 2080
ip lisp locator reachability exclude 2081
ip lisp map-cache-limit 2082
ip lisp map-cache drop native-forward map-request priority weight 2083
ip lisp map-request-source 2084
ip lisp map-resolver 2085
ip lisp map-server 2086
ip lisp map-server try-map-cache 2087
ip lisp multicast 2088
ip lisp nat-traversal 2089
ip lisp ntr 2090
ip lisp null0-is-alt-miss 2091
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxii
Contents
Page 63
ip lisp proxy-etr 2092
ip lisp proxy-itr 2093
ip lisp short-map-cache-ttl 2094
ip lisp shortest-eid-prefix-length 2095
ip lisp source-locator 2096
ip lisp translate inside outside 2097
ip lisp use-bgp-locators 2098
ip lisp use-petr priority weight 2099
ip load-sharing address 2100
ip local-proxy-arp 2101
ip local policy route-map 2102
ip mfwd event-history cli 2103
ip mfwd event-history l2 2104
ip mfwd event-history nbm 2105
ip mfwd event-history packet 2106
ip mfwd event-history vrf 2107
ip mfwd mstatic register 2108
ip mroute 2109
ip msdp description 2110
ip msdp event-history cli 2111
ip msdp event-history events 2112
ip msdp event-history routes 2113
ip msdp event-history tcp 2114
ip msdp flush-routes 2115
ip msdp group-limit source 2116
ip msdp keepalive 2117
ip msdp mesh-group 2118
ip msdp originator-id 2119
ip msdp password 2120
ip msdp peer connect-source 2121
ip msdp reconnect-interval 2122
ip msdp redistribute 2123
ip msdp sa-interval 2124
ip msdp sa-limit 2125
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxiii
Contents
Page 64
ip msdp sa-policy in 2126
ip msdp sa-policy out 2127
ip msdp shutdown 2128
ip mtu eigrp 2129
ip multicast multipath 2130
ip multicast multipath resilient 2131
ip multicast overlay-distributed-dr 2132
ip multicast overlay-spt-only 2133
ip multicast rpf select vrf group-list 2134
ip name-server 2135
ip nat inside 2137
ip nat inside source 2138
ip nat outside source 2140
ip nat pool netmask 2142
ip nat pool netmask 2143
ip nat translation 2144
ip nat translation creation-delay 2145
ip nat translation max-entries 2146
ip nat translation sampling-timeout 2147
ip next-hop-self eigrp 2148
ip offset-list eigrp 2149
ip ospf advertise-subnet 2150
ip ospf authentication-key 2151
ip ospf authentication 2152
ip ospf authentication key-chain 2153
ip ospf bfd 2154
ip ospf cost 2155
ip ospf dead-interval 2156
ZZZ_4621 2157
ip ospf event-history cli 2158
ip ospf event-history detail 2159
ip ospf hello-interval 2160
ip ospf message-digest-key md5 2161
ip ospf mtu-ignore 2162
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxiv
Contents
Page 65
ip ospf network broadcast 2163
ip ospf network point-to-point 2164
ip ospf passive-interface 2165
ip ospf prefix-attributes n-flag-clear 2166
ip ospf priority 2167
ip ospf retransmit-interval 2168
ip ospf shutdown 2169
ip ospf transmit-delay 2170
ip passive-interface eigrp 2171
ip pim anycast-rp 2172
ip pim assert-rate-limit 2173
ip pim auto-enable 2174
ip pim auto-rp listen 2175
ip pim auto-rp mapping-agent-policy 2176
ip pim auto-rp mapping-agent send-rp-discovery 2177
ip pim auto-rp rp-candidate-policy 2178
ip pim auto-rp rp-candidate send-rp-announce group-list route-map prefix-list 2179
ip pim bfd-instance 2180
ip pim bfd 2181
ip pim bidir-rp-limit 2182
ip pim border-router 2183
ip pim border 2184
ip pim bsr-candidate 2185
ip pim bsr bsr-policy 2186
ip pim bsr listen 2187
ip pim bsr rp-candidate-policy 2188
ip pim dr-delay 2189
ip pim dr-priority 2190
ip pim event-history assert 2191
ip pim event-history bidir 2192
ip pim event-history cli 2193
ip pim event-history data-register-receive 2194
ip pim event-history hello 2195
ip pim event-history join-prune-summary 2196
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxv
Contents
Page 66
ip pim event-history join-prune-tw 2197
ip pim event-history join-prune 2198
ip pim event-history mrib 2199
ip pim event-history mvpn 2200
ip pim event-history nbm 2201
ip pim event-history null-register 2202
ip pim event-history packet 2203
ip pim event-history pim-library 2204
ip pim event-history rp 2205
ip pim event-history txlist 2206
ip pim event-history vpc 2207
ip pim event-history vrf 2208
ip pim evpn-border-leaf 2209
ip pim extranet 2210
ip pim file-debug 2211
ip pim flush-routes 2212
ip pim group-list 2213
ip pim hello-authentication ah-md5 2214
ip pim hello-interval 2215
ip pim isolate 2216
ip pim jp-interval 2217
ip pim jp-policy 2218
ip pim log-neighbor-changes 2219
ip pim neighbor-policy prefix-list 2220
ip pim passive 2221
ip pim pre-build-spt 2222
ip pim register-policy 2223
ip pim register-rate-limit 2224
ip pim register-source 2225
ip pim register-until-stop 2226
ip pim rp-address 2227
ip pim rp-candidate group-list route-map prefix-list 2228
ip pim sg-expiry-timer infinity 2229
ip pim sparse-mode 2230
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxvi
Contents
Page 67
ip pim ssm 2231
ip pim state-limit 2232
ip pim strict-rfc-compliant 2233
ip pim strict-rfc-compliant 2234
ip ping source-interface 2235
ip policy match router-address 2236
ip policy route-map 2237
ip port-unreachable 2238
ip port access-group 2239
ip port access-group 2240
ip prefix-list description 2241
ip prefix-list permit 2242
ip proxy-arp 2243
ip radius source-interface 2244
ip redirects 2245
ip rip authentication key-chain 2246
ip rip authentication mode text 2247
ip rip metric 2248
ip rip passive-interface 2249
ip rip poison-reverse 2250
ip rip route-filter route in 2251
ip rip summary-address 2252
ip route 2253
ip route static bfd 2254
ip router eigrp 2255
ip router isis 2256
ip router ospf area 2257
ip router ospf multi-area 2258
ip router rip 2259
ip routing download-on-convergence 2260
ip routing event-history 2261
ip routing multicast event-history cli 2262
ip routing multicast event-history mdt 2263
ip routing multicast event-history mfdm-debugs 2264
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxvii
Contents
Page 68
ip routing multicast event-history mfdm-events 2265
ip routing multicast event-history mfdm-stats 2266
ip routing multicast event-history nbm 2267
ip routing multicast event-history notify-clients 2268
ip routing multicast event-history rib-summary 2269
ip routing multicast event-history rib 2270
ip routing multicast event-history urib-debugs 2271
ip routing multicast event-history vrf 2272
ip routing multicast file-debug 2273
ip routing multicast holddown 2274
ip routing multicast mfdm-buffer-route-count 2275
ip routing multicast software-replicate 2276
ip routing multicast trace enable 2277
ip routing multicast trace entries 2278
ip routing multicast trace records 2279
ip secondary 2280
ip service-reflect destination to mask-len source 2281
ip service-reflect mode regular 2282
ip sla 2283
ip sla group schedule 2284
ip sla logging traps 2286
ip sla reaction-configuration react 2287
ip sla reaction-trigger 2288
ip sla reset 2289
ip sla responder 2290
ip sla responder twamp 2291
ip sla restart 2292
ip sla schedule 2293
ip sla server twamp 2295
ip source-route 2296
ip source binding vlan interface 2297
ip source icmp-errors 2298
ip split-horizon eigrp 2299
ip ssh source-interface 2300
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxviii
Contents
Page 69
ip summary-address eigrp ipv6 summary-address eigrp 2301
ip tacacs source-interface 2302
ip tcp mss 2303
ip tcp path-mtu-discovery 2304
ip tcp synwait-time 2305
ip telnet source-interface 2306
ip tftp source-interface 2307
ip traceroute source-interface 2308
ip ttl 2309
ip udp relay addrgroup 2310
ip udp relay subnet-broadcast 2311
ip unnumbered 2312
ip unreachables 2313
ip verify source dhcp-snooping-vlan 2314
ip verify unicast source reachable-via rx 2315
ipv6 2316
ipv6 access-class 2318
ipv6 access-list 2319
ipv6 access-list match-local-traffic 2320
ipv6 address 2321
ipv6 address dhcp 2322
ipv6 address use-link-local-only 2323
ipv6 adjacency-stale-timer 2324
ipv6 adjacency route distance 2325
ipv6 amt gateway 2326
ipv6 amt relay 2327
ipv6 destination 2328
ipv6 dhcp-ldra 2329
ipv6 dhcp-ldra attach-policy 2330
ipv6 dhcp-ldra attach-policy vlan client 2331
ipv6 dhcp guard 2332
ipv6 dhcp guard 2333
ipv6 dhcp guard policy 2334
ipv6 dhcp relay 2335
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxix
Contents
Page 70
ipv6 dhcp relay address 2336
ipv6 dhcp relay address ipv6 dhcp relay address 2337
ipv6 dhcp relay option type cisco 2338
ipv6 dhcp relay option vpn 2339
ipv6 dhcp relay source-interface 2340
ipv6 dhcp relay source-interface 2341
ipv6 flow monitor input 2342
ipv6 flow monitor input 2343
ipv6 flow monitor input 2344
ipv6 forward 2345
ipv6 host 2346
ipv6 link-local 2347
ipv6 local policy route-map 2348
ipv6 mld group-timeout 2349
ipv6 mld immediate-leave 2350
ipv6 mld join-group 2351
ipv6 mld last-member-query-count 2352
ipv6 mld last-member-query-response-time 2353
ipv6 mld querier 2354
ipv6 mld query-interval 2355
ipv6 mld query-max-response-time 2356
ipv6 mld report-link-local-groups 2357
ipv6 mld report 2358
ipv6 mld robustness-variable 2359
ipv6 mld ssm-translate 2360
ipv6 mld startup-query-count 2361
ipv6 mld startup-query-interval 2362
ipv6 mld state-limit 2363
ipv6 mld static 2364
ipv6 mld version 2365
ipv6 nd cache limit 2366
ipv6 nd dad attempts 2367
ipv6 nd dadns-discover 2368
ipv6 nd hop-limit 2369
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxx
Contents
Page 71
ipv6 nd mac-extract 2370
ipv6 nd managed-config-flag 2371
ipv6 nd mtu 2372
ipv6 nd ns-interval 2373
ipv6 nd off-list timeout 2374
ipv6 nd other-config-flag 2375
ipv6 nd prefix 2376
ipv6 nd prefix default 2377
ipv6 nd ra-interval 2378
ipv6 nd ra-lifetime 2379
ipv6 nd ra dns search-list sequence 2380
ipv6 nd ra dns search-list suppress 2381
ipv6 nd ra dns server sequence 2382
ipv6 nd ra dns server suppress 2383
ipv6 nd ra route suppress 2384
ipv6 nd raguard 2385
ipv6 nd raguard 2386
ipv6 nd raguard attach-policy 2387
ipv6 nd raguard policy 2388
ipv6 nd reachable-time 2389
ipv6 nd retrans-timer 2390
ipv6 nd route route-preference High Low Medium infinite 2391
ipv6 nd router-preference High Low Medium 2392
ipv6 nd solicit-na accept 2393
ipv6 nd suppress-ra 2394
ipv6 nd synchronize 2395
ipv6 neighbor 2396
ipv6 neighbor allow-static-neighbor-outside-subnet 2397
ipv6 neighbor binding 2398
ipv6 neighbor binding 2399
ipv6 neighbor binding logging 2400
ipv6 neighbor binding max-entries 2401
ipv6 neighbor tracking 2402
ipv6 pim anycast-rp 2403
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxi
Contents
Page 72
ipv6 pim bidir-rp-limit 2404
ipv6 pim border 2405
ipv6 pim bsr-candidate 2406
ipv6 pim bsr bsr-policy 2407
ipv6 pim bsr listen 2408
ipv6 pim bsr rp-candidate-policy 2409
ipv6 pim dr-priority 2410
ipv6 pim event-history assert-receive 2411
ipv6 pim event-history bidir 2412
ipv6 pim event-history hello 2413
ipv6 pim event-history join-prune 2414
ipv6 pim event-history null-register 2415
ipv6 pim event-history packet 2416
ipv6 pim event-history rp 2417
ipv6 pim event-history vrf 2418
ipv6 pim flush-routes 2419
ipv6 pim hello-interval 2420
ipv6 pim isolate 2421
ipv6 pim jp-policy 2422
ipv6 pim log-neighbor-changes 2423
ipv6 pim neighbor-policy 2424
ipv6 pim passive 2425
ipv6 pim register-policy 2426
ipv6 pim register-rate-limit 2427
ipv6 pim rp-address 2428
ipv6 pim rp-candidate group 2429
ipv6 pim sparse-mode 2430
ipv6 pim ssm 2431
ipv6 pim state-limit 2432
ipv6 pim use-shared-tree-only spt-threshold infinity group-list 2433
ipv6 policy route-map 2434
ipv6 port traffic-filter 2435
ipv6 prefix-list description 2436
ipv6 prefix-list permit 2437
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxii
Contents
Page 73
ipv6 queue-packets 2438
ipv6 redirects 2439
ipv6 route 2440
ipv6 route static bfd 2441
ipv6 router isis 2442
ipv6 router ospfv3 area 2443
ipv6 router ospfv3 multi-area 2444
ipv6 routing event-history size 2445
ipv6 routing multicast event-history cli 2446
ipv6 routing multicast event-history mfdm-debugs 2447
ipv6 routing multicast event-history mfdm-events 2448
ipv6 routing multicast event-history mfdm-stats 2449
ipv6 routing multicast event-history rib-summary 2450
ipv6 routing multicast event-history rib 2451
ipv6 routing multicast event-history vrf 2452
ipv6 routing multicast holddown 2453
ipv6 routing multicast software-replication 2454
ipv6 snooping 2455
ipv6 snooping 2456
ipv6 snooping policy 2457
ipv6 switch-packets 2458
ipv6 traffic-filter 2459
ipv6 unreachables 2460
ipv6 verify unicast source reachable-via rx 2461
is-type 2462
ishow cli find nodes 2463
ishow cli modes 2464
ishow cli nodes 2465
ishow cli paths 2466
ishow cli tags 2467
ishow core backtrace 2468
isis authentication-check 2469
isis authentication-check level-1 2470
isis authentication-check level-2 2471
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxiii
Contents
Page 74
isis authentication-type cleartext 2472
isis authentication-type cleartext 2473
isis authentication key-chain 2474
isis authentication key-chain 2475
isis bfd 2476
isis circuit-type 2477
isis csnp-interval level 2478
isis event-history adjacency 2479
isis event-history cli 2480
isis event-history csnp 2481
isis event-history dis 2482
isis event-history events 2483
isis event-history graceful 2484
isis event-history ha 2485
isis event-history iih 2486
isis event-history lsp-flood 2487
isis event-history lsp-gen 2488
isis event-history mtr 2489
isis event-history perf 2490
isis event-history psnp 2491
isis event-history redist 2492
isis event-history spf-leaf 2493
isis event-history spf-tree 2494
isis event-history sr 2495
isis event-history tlv 2496
isis event-history ulib 2497
isis event-history urib 2498
isis hello-interval 2499
isis hello-interval level 2500
isis hello-multiplier 2501
isis hello-multiplier level 2502
isis hello-padding 2503
isis ipv6 bfd 2504
isis ipv6 metric 2505
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxiv
Contents
Page 75
isis lsp-interval 2506
isis mesh-group 2507
isis metric 2508
isis mtu-check 2509
isis mtu-check level 2510
isis network point-to-point 2511
isis passive-interface 2512
isis prefix-attributes n-flag-clear 2513
isis priority level 2514
isis retransmit-interval 2515
isis retransmit-throttle-interval 2516
isis shutdown 2517
isolate 2518
isolate 2519
isolate 2520
isolate 2521
isolate 2522
isolate 2523
isolate 2524
itd 2525
itd device-group 2526
itd session access-list refresh 2527
itd session device-group 2528
itd statistics 2529
J Commands 2531C H A P T E R 1 1
job name 2532
json-pretty 2533
json-pretty 2534
json 2535
json 2536
K Commands 2537C H A P T E R 1 2
key-octet-string 7 cryptographic-algorithm AES_128_CMAC 2538
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxv
Contents
Page 76
key-octet-string 7 cryptographic-algorithm AES_256_CMAC 2539
key-octet-string cryptographic-algorithm AES_128_CMAC 2540
key-octet-string cryptographic-algorithm AES_256_CMAC 2541
key-server-priority 2542
key-string 2543
key-string 7 2544
key 2545
key 2546
key chain 2547
key config-key hex 2548
kill-everyone 2549
kill background 2550
kstack multicast-udp 2551
kubernetes server ip-address port 2552
L Commands 2553C H A P T E R 1 3
l2rib dup-host-mac-detection 2561
l2rib dup-host-mac-recovery 2562
l2rib event-history size 2563
l3vm event-history 2564
label-allocation-mode per-vrf 2565
label allocate global 2566
lacp fast-select-hot-standby 2567
lacp graceful-convergence 2568
lacp max-bundle 2569
lacp min-links 2570
lacp mode delay 2571
lacp mode delay 2572
lacp port-priority 2573
lacp rapid-transition 2574
lacp rate 2575
lacp rate 2576
lacp suspend-individual 2577
lacp system-mac 2578
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxvi
Contents
Page 77
lacp system-priority 2579
lacp vpc-convergence 2580
last 2581
latency 2582
latency 2583
latency quantization 2584
latency quantization 2585
layer-2 multicast lookup mac 2586
layer-2 multicast lookup mac 2587
layer2-switched flow monitor input 2588
layer3 peer-router 2589
layer3 peer-router syslog 2590
ldap-search-map 2591
ldap-search-map 2592
ldap-server deadtime 2593
ldap-server host 2594
ldap-server host test rootDN 2596
ldap-server port 2597
ldap-server timeout 2598
ldap search-map 2599
less 2600
license expiry check_interval 2601
limit-resource m4route-mem maximum equal-to-min 2602
limit-resource m6route-mem maximum 2603
limit-resource module-type 2604
limit-resource monitor-session-erspan-dst minimum maximum equal-to-min 2605
limit-resource monitor-session-inband-src minimum maximum equal-to-min 2606
limit-resource monitor-session minimum maximum equal-to-min 2607
limit-resource port-channel minimum maximum 2608
limit-resource u4route-mem maximum equal-to-min 2609
limit-resource u6route-mem maximum equal-to-min 2610
limit-resource vlan minimum maximum equal-to-min 2611
limit-resource vrf minimum maximum equal-to-min 2612
limit address-count 2613
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxvii
Contents
Page 78
line console 2614
line console 2615
line vty 2616
line vty 2617
link-management timers bandwidth 2618
link-state-trap 2619
link debounce 2620
link rxlos 2621
link transmit reset-skip 2622
lisp 2623
lisp ddt 2624
lisp ddt authoritative-prefix eid-prefix 2625
lisp ddt delegate eid-prefix 2626
lisp ddt map-server-peer eid-prefix 2627
lisp ddt root 2628
lisp dynamic-eid 2629
lisp dynamic-eid 2630
lisp explicit-locator-path 2631
lisp explicit-locator-path 2632
lisp extended-subnet-mode 2633
lisp geo-coordinates 2634
lisp instance-id 2635
lisp loc-reach-algorithm 2636
lisp merge-registrations site-id 2637
lisp mobility 2638
lisp mobility test-liveness 2639
lisp security 2640
lisp site 2641
lisp site 2642
lisp smr-locators 2643
lisp to 2644
list 2645
list 2646
listobject-boolean not 2647
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxviii
Contents
Page 79
listobject-weight weight threshold-weight 2648
listobject 2649
lldp 2650
lldp dcbx version auto 2651
lldp dcbx version cee 2652
lldp eee rx_wake_time 2653
lldp receive 2654
lldp tlv-select eee 2655
lldp tlv-select management-address v4 2656
lldp tlv-set management-address 2657
lldp tlv-set management-address ipv6 2658
lldp tlv-set vlan 2659
lldp transmit 2660
load-balance 2661
load-balance 2662
load-balance 2663
load-interval 2664
load-interval 2665
load-interval counter 2666
load-interval counter 2667
load 2668
load 2669
load 2670
load 2671
local-as 2672
local-as 2673
local-label prefix 2674
local-label prefix 2675
locator-led 2676
lockdown 2677
log-adjacency-changes 2678
log-adjacency-changes 2679
log-adjacency-changes 2680
log-adjacency-changes 2681
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxix
Contents
Page 80
log-adjacency-changes 2682
log-adjacency-changes 2683
log-event-type 2684
log-neighbor-changes 2685
log-neighbor-changes 2686
log-neighbor-warnings 2687
logging 2688
logging 2689
logging abort 2690
logging console 2691
logging debug 2692
logging distribute 2693
logging drop threshold 2694
logging drop threshold 2695
logging event link enable 2696
logging event port link-status 2697
logging event port link-status 2698
logging event port link-status 2699
logging event port link-status default 2700
logging event port trunk-status 2701
logging event port trunk-status 2702
logging event port trunk-status default 2703
logging flow-mod 2704
logging flow-mod 2705
logging ip access-list cache 2706
logging ip access-list cache entries 2707
logging ip access-list detailed 2708
logging ip access-list include sgt 2709
logging level 2710
logging level 2711
logging level 2712
logging level 2713
logging level 2715
logging level 2716
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxx
Contents
Page 81
logging level 2717
logging level 2718
logging level aaa 2719
logging level acllog 2720
logging level aclmgr 2721
logging level adbm 2722
logging level adjmgr 2723
logging level all 2724
logging level amt 2725
logging level arp 2726
logging level ascii-cfg 2727
logging level assoc_mgr 2728
logging level backup 2729
logging level bfd 2730
logging level bgp 2731
logging level bloggerd 2732
logging level bootvar 2733
logging level callhome 2734
logging level capability 2735
logging level catena 2736
logging level cdp 2737
logging level cert 2738
logging level cfs 2739
logging level clis 2740
logging level clk_mgr 2741
logging level confcheck 2742
logging level copp 2743
logging level core 2744
logging level cts 2745
logging level dhclient 2746
logging level dhcp_snoop 2747
logging level diagclient 2748
logging level diagmgr 2749
logging level dot1x 2750
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxxi
Contents
Page 82
logging level ecp 2751
logging level eigrp 2752
logging level eltm 2753
logging level epp 2754
logging level ethdstats 2755
logging level ethpm 2756
logging level ethpm link 2757
logging level evb 2758
logging level evmc 2759
logging level evmed 2760
logging level evms 2761
logging level fabric forwarding 2762
logging level fcoe_mgr 2763
logging level feature-mgr 2764
logging level fs-daemon 2765
logging level gpixm 2766
logging level hardware-telemetry 2767
logging level hsrp 2768
logging level icam 2769
logging level igmp 2770
logging level im 2771
logging level imp 2772
logging level interface-vlan 2773
logging level ip pim 2774
logging level ip sla responder 2775
logging level ip sla sender 2776
logging level ip sla twamp-server 2777
logging level ipconf 2778
logging level ipfib 2779
logging level ipqos 2780
logging level ipv6 pim 2781
logging level iscm 2782
logging level iscm 2783
logging level isis 2784
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxxii
Contents
Page 83
logging level keystore 2785
logging level l2fm 2786
logging level l2rib 2787
logging level l3vm 2788
logging level lacp 2789
logging level ldap 2790
logging level lem-mgr 2791
logging level license 2792
logging level lim 2793
logging level lisp 2794
logging level lldp 2795
logging level m2rib 2796
logging level mfdm 2797
logging level mfwd 2798
logging level mmode 2799
logging level module 2800
logging level monitor 2801
logging level msdp 2802
logging level mvsh 2803
logging level nat 2804
logging level nbm 2805
logging level netstack 2806
logging level nfm 2807
logging level ngoam 2808
logging level npv 2809
logging level ntp 2810
logging level nxsdk 2811
logging level openflow 2812
logging level orib 2813
logging level ospf 2814
logging level ospfv3 2815
logging level pfstat 2816
logging level pixm 2817
logging level pktmgr 2818
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxxiii
Contents
Page 84
logging level platform 2819
logging level plbm 2820
logging level plcmgr 2821
logging level pltfm_config 2822
logging level plugin 2823
logging level poap 2824
logging level poed 2825
logging level port-profile 2826
logging level port-resources 2827
logging level port-security 2828
logging level port 2829
logging level port_client 2830
logging level port_lb 2831
logging level port link-failure 2832
logging level private-vlan 2833
logging level ptp 2834
logging level radius 2835
logging level res_mgr 2836
logging level rip 2837
logging level rpm 2838
logging level rsvp 2839
logging level sal 2840
logging level san 2841
logging level scheduler 2842
logging level security 2843
logging level session-mgr 2844
logging level sflow 2845
logging level smartc 2846
logging level smm 2847
logging level snmpd 2848
logging level snmpmib_proc 2849
logging level spanning 2850
logging level spm 2851
logging level stripcl 2852
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxxiv
Contents
Page 85
logging level sysmgr 2853
logging level tacacs 2854
logging level tamnw 2855
logging level track 2856
logging level tunnel 2857
logging level u2rib 2858
logging level u6rib 2859
logging level udld 2860
logging level ufdm 2861
logging level urib 2862
logging level vdc_mgr 2863
logging level virtual-service 2864
logging level vlan_mgr 2865
logging level vmm 2866
logging level vmtracker 2867
logging level vpc 2868
logging level vrrp 2869
logging level vrrpv3 2870
logging level vsan 2871
logging level vshd 2872
logging level vtp 2873
logging level wwnm 2874
logging level xbar 2875
logging logfile 2876
logging message interface type ethernet 2877
logging module 2878
logging monitor 2879
logging origin-id 2880
logging rate-limit 2881
logging server 2882
logging server dns-refresh-interval 2884
logging source-interface 2885
logging timestamp 2886
login on-failure log 2887
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxxv
Contents
Page 86
login on-success log 2888
logout-warning 2889
low-memory exempt 2890
lshow 2891
lshow 2892
lsp-gen-interval 2893
lsp-gen-interval 2894
lsp-gen-interval 2895
lsp-mtu 2896
lsp-mtu 2897
lsp-mtu 2898
lsp 2899
lsp 2900
lsp attributes 2901
MCommands 2903C H A P T E R 1 4
m2rib debug ftag 2908
m2rib debug gr-route add nh 2909
m2rib debug log-size event-history 2911
m2rib debug log-size transactions 2912
m2rib debug omf enable 2913
m2rib debug pkt-recv enable 2914
m2rib debug swroute nh 2915
m2rib debug topo 2916
m2rib debug topo loop-flush-timeout 2917
mac-addr 2918
mac-address 2919
mac-address 2920
mac-address 2921
mac-address bpdu source version 2 2922
mac-address destination 2923
mac-address ipv6-extract 2924
mac-learn disable 2925
mac-learn disable 2926
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxxvi
Contents
Page 87
mac-list permit 2927
mac access-list 2928
mac address-table aging-time 2929
mac address-table guard-vpc-peergw-mac 2930
mac address-table limit system 2931
mac address-table loop-detect port-down 2932
mac address-table multicast vlan interface 2933
mac address-table notification mac-move 2934
mac address-table notification threshold 2935
mac address-table static vlan interface 2936
mac address-table static vni 2937
mac address 2938
mac address inherit 2939
mac advert interval 2940
mac packet-classify 2941
mac packet-classify 2942
mac port access-group 2943
managed-config-flag 2944
management 2945
map-notify-group 2946
map-server key 2947
marker-packet-n3500 2948
marker-packet 2949
master ipv4 2950
match-address 2951
match 2952
match 2954
match 2955
match access-group name 2959
match address 2960
match as-number 2961
match as-number as-path-list 2962
match as-path 2963
match class-map 2964
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxxvii
Contents
Page 88
match community 2965
match cos 2966
match cos 2967
match datalink 2968
match datalink 2969
match dscp 2970
match dscp 2971
match exception 2972
match extcommunity 2973
match interface 2974
match ip address 2975
match ip address prefix-list 2976
match ip multicast rp 2977
match ip next-hop prefix-list 2978
match ip protocol 2979
match ip route-source prefix-list 2980
match ipv4 protocol 2981
match ipv4 source address 2982
match ipv4 source address 2983
match ipv4 transport destination 2984
match ipv6 2985
match ipv6 2986
match ipv6 address 2987
match ipv6 address prefix-list 2988
match ipv6 multicast rp 2989
match ipv6 next-hop prefix-list 2990
match ipv6 protocol 2991
match ipv6 route-source prefix-list 2992
match ipv6 transport destination 2993
match metric 2994
match ospf-area 2995
match protocol 2996
match protocol arp 2997
match qos-group 2998
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxxviii
Contents
Page 89
match qos-group2 2999
match qos-group2 3000
match qos-group 3001
match redirect 3002
match route-type 3003
match source-protocol 3004
match tag 3005
match transport destination 3006
max-backoff 3007
max-backoff 3008
max-lsa 3009
max-lsa 3010
max-lsp-lifetime 3011
max-lsp-lifetime 3012
max-lsp-lifetime 3013
max-metric router-lsa 3014
max-metric router-lsa 3015
max-ports 3016
max-ports 3017
maxas-limit 3018
maximum-paths 3019
maximum-paths 3020
maximum-paths 3021
maximum-paths 3022
maximum-paths 3023
maximum-paths 3024
maximum-paths 3025
maximum-paths 3026
maximum-paths eibgp 3027
maximum-paths mixed 3028
maximum-peers 3029
maximum-prefix 3030
maximum-prefix 3031
maximum-prefix 3032
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)lxxxix
Contents
Page 90
maximum routes 3033
mdix auto 3034
mdt asm-use-shared-tree 3035
mdt data 3036
mdt data bidir-enable 3037
mdt default 3038
mdt enforce-bgp-mdt-safi 3039
mdt mtu 3040
mdt pim hello-interval 3041
mdt pim jp-interval 3042
mdt source 3043
media-type auto 3044
media-type rj45 3045
media-type sfp 3046
media 3047
medium 3048
medium broadcast 3049
medium broadcast 3050
medium p2p 3051
medium p2p 3052
member vlan 3053
member vni 3054
member vni 3055
member vni associate-vrf 3056
message-digest-key md5 3057
message-digest-key md5 3058
metric-style transition 3059
metric-type 3060
metric direct 0 3061
metric maximum-hops 3062
metric rib-scale 3063
metric version 64bit 3064
metric weights 3065
mkdir 3066
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xc
Contents
Page 91
mode 3067
mode 3068
mode 3069
mode tap-aggregation 3070
module transceiver-frequency 3071
monitor erspan granularity 3072
monitor erspan origin ip-address 3073
monitor erspan switch-id 3074
monitor session 3075
monitor session shut 3076
monitor session type acl-capture 3077
monitor session type erspan-destination 3078
monitor session type erspan-source 3079
monitor session warp 3080
monitor session warp 3081
mount 3082
mount slot0 3083
move 3084
mst designated priority 3085
mst root priority 3086
mtrace 3087
mtu 3088
mtu1 3089
mtu 3090
mtu 3091
mtu 3092
mtu 3093
mtu 3094
mtu 3095
multi-topology 3096
multicast 3097
multisite border-gateway interface 3098
multisite ingress-replication 3099
mvr-config 3100
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xci
Contents
Page 92
mvr-group 3101
mvr-group 3102
mvr-group 3103
mvr-group 3104
mvr-group 3105
mvr-group 3106
mvr-group 3107
mvr-group 3108
mvr-suppress-query vlan 3109
mvr-type receiver 3110
mvr-type source 3111
mvr-vlan 3112
mvr-vlan 3113
N Commands 3115C H A P T E R 1 5
name-lookup 3118
name-lookup 3119
name 3120
name 3121
name 3122
nat destination 3123
nbm external-link 3124
nbm flow-policy 3125
nbm flow acceptance-mode guaranteed nbm flow acceptance-mode 3126
nbm flow asm range 3127
nbm flow bandwidth kbps mbps gbps 3128
nbm flow dscp 3129
nbm host-policy 3130
nbm mode pim-active 3131
nbm reserve unicast fabric bandwidth 3132
negotiate auto 3133
negotiate auto 25000 3134
neighbor-down fib-accelerate 3135
neighbor 3136
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xcii
Contents
Page 93
neighbor 3137
neighbor 3138
neighbor 3139
neighbor 3140
neighbor maximum-prefix 3141
nemo config address port interval 3142
net 3143
net 3144
net 3145
network 3146
network 3147
network 3148
network 3149
next-address exclude-address 3150
next-hop-self 3151
next-hop-self 3152
next-hop-third-party 3153
next-hop-third-party 3154
next-hop out-label explicit-null implicit-null next-hop auto-resolve out-label explicit-null implicit-null3155
next-hop out-label explicit-null implicit-null next-hop auto-resolve out-label explicit-null implicit-null3156
nexthop route-map 3157
nexthop trigger-delay critical non-critical 3158
ngoam authentication-key 3159
ngoam connect-check 3160
ngoam install acl 3161
ngoam profile 3162
ngoam xconnect hb-interval 3163
no-more 3164
no 3165
no 3166
no 3167
no 3168
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xciii
Contents
Page 94
no 3169
no 3170
no 3171
no 3174
no 3179
no 3183
no 3186
no 3189
no 3192
no 3195
no 3198
no 3201
no 3203
no 3204
no 3205
no 3206
node 3207
node 3208
node 3209
node ip 3210
node ip 3211
npiv enable 3212
npv auto-load-balance disruptive 3213
npv traffic-map server-interface external-interface 3214
nsf await-redist-proto-convergence 3215
ntp access-group 3216
ntp access-group match-all 3217
ntp allow private 3218
ntp authenticate 3219
ntp authentication-key md5 3220
ntp drop-aged-packet 3221
ntp logging 3222
ntp master 3223
ntp passive 3224
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xciv
Contents
Page 95
ntp peer 3225
ntp rts-update 3226
ntp server 3227
ntp source-interface 3228
ntp source 3229
ntp sync-retry 3230
ntp trusted-key 3231
nv overlay evpn 3232
nxapi certificate 3233
nxapi flow 3234
nxapi http port 3235
nxapi ssl ciphers weak 3236
nxapi ssl protocols 3237
nxapi use-vrf management default 3238
nxsdk enable app 3239
nxsdk service-name 3240
O Commands 3241C H A P T E R 1 6
oam-channel 3243
object-group ip address 3244
object-group ip port 3245
object-group ipv6 address 3246
object-group udp relay ip address 3247
object-group udp relay ip address 3248
object-track 3249
of-port interface 3250
on-demand color 3251
openflow 3252
operation-packet-priority normal 3253
option exporter-stats timeout 3254
option interface-table timeout 3255
orib event-history 3256
orib orib_api_init 3257
ospfv3 authentication 3258
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xcv
Contents
Page 96
ospfv3 bfd 3259
ospfv3 cost 3260
ospfv3 dead-interval 3261
ospfv3 event-history 3262
ospfv3 event-history cli 3263
ospfv3 event-history detail 3264
ospfv3 event-history detail 3265
ospfv3 hello-interval 3266
ospfv3 instance 3267
ospfv3 mtu-ignore 3268
ospfv3 network broadcast 3269
ospfv3 network point-to-point 3270
ospfv3 passive-interface 3271
ospfv3 priority 3272
ospfv3 retransmit-interval 3273
ospfv3 shutdown 3274
ospfv3 transmit-delay 3275
other-config-flag 3276
overlay-encapsulation 3277
overwrite-vlan 3278
owner 3279
P Commands 3281C H A P T E R 1 7
packet-size 3288
param-list param-list 3289
parity 3290
parity 3291
passive-interface default 3292
passive-interface default 3293
passive-interface default 3294
passive-interface default 3295
password 3296
password 3297
password 3298
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xcvi
Contents
Page 97
password prompt username 3299
password secure-mode 3300
password strength-check 3301
path-option dynamic explicit identifier 3302
path-selection metric igp 3303
path-selection metric igp 3304
path-selection overload allow 3305
path 3306
path next-hop out-label-stack 3307
pause 3308
pause 3309
pause buffer-size2 pause-threshold2 resume-threshold2 3310
pause priority 3311
payload 3312
payload test pattern-type pad 3313
pcc 3314
pce-address ipv4 3315
peer-gateway 3316
peer-ip 3317
peer-keepalive destination 3318
peer-switch 3320
peer-type fabric 3321
peer-vtep 3322
peer ip 3323
peer ip 3324
peer local service 3325
peer local service 3326
peer vpc 3327
per-ingress-port-mtu-mode 3328
perf 3329
periodic-inventory notification 3330
periodic-inventory notification interval 3331
periodic to 3332
periodic to 3333
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xcvii
Contents
Page 98
permit interface 3334
permit vlan 3335
permit vrf 3336
permit vsan 3337
personality 3338
personality backup 3339
personality restore 3340
phone-contact 3341
pim 3342
ping 3343
ping6 3345
platform access-list capture 3346
platform access-list fp_dnl 3347
platform access-list update 3348
platform acl tap-agg 3349
platform forwarding interface statistics mode mpls 3350
platform forwarding layer-2 f1 exclude supervisor 3351
platform ip verify 3352
platform ipv6 verify 3354
platform qos 3355
platform qos 3356
platform qos 3357
platform qos 3358
platform qos 3359
platform qos 3360
platform qos 3361
platform qos 3362
platform qos 3364
platform qos 3365
platform qos 3366
platform qos 3367
platform qos 3368
platform qos 3369
platform qos 3370
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xcviii
Contents
Page 99
platform qos buffer peak monitor counter0 class 3371
platform qos buffer peak monitor counter1 class 3372
platform qos classify ns-only 3373
platform qos eoq 3374
platform qos include ipg 3375
platform qos ing 3376
platform qos ing 3377
platform qos mac ipg 3378
platform qos nodrop-PG-thresholds-FX PG-size 3379
platform qos nodrop-PG-thresholds PG-size 3380
platform qos nodrop-PG-thresholds PG-size Red-threshold Yellow-threshold Green-threshold 3381
platform qos nodrop-queue-thresholds-FX Queue-green 3382
platform qos nodrop-queue-thresholds-roc Queue-green 3383
platform qos ns 3384
platform qos q-noise percent 3385
platform rate-limiter 3386
platform rate-limiter 3388
platform rate-limiter access-list-log 3390
platform rate-limiter span-egress 3391
plb 3392
plb analytics 3393
plb device-group 3394
police 3395
police 3399
police 3401
police 3403
police police pps 3407
police police pps 3409
policy-map 3411
policy-map type control-plane 3412
policy-map type network-qos 3413
policy-map type queuing 3414
policy 3415
policy 3416
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)xcix
Contents
Page 100
policy 3417
pop 3418
port-channel bfd destination 3419
port-channel bfd start 3420
port-channel bfd track-member-link 3421
port-channel fast-convergence 3422
port-channel hash-distribution 3423
port-channel limit 3424
port-channel load-balance 3425
port-channel load-balance1 ethernet 3426
port-channel load-balance2 resilient 3427
port-channel load-balance ethernet 3428
port-channel load-defer 3429
port-channel port hash-distribution 3430
port-channel port load-defer 3431
port-channel scale-fanout 3432
port-group 3433
port-group 3434
port-license 3435
port-license 3436
port-profile 3437
port-type 3438
port 3439
port 3440
port control 3441
port control 3442
port destination 3443
port type ethernet 3444
postcard-telemetry exporter 3445
postcard-telemetry flow-profile 3446
postcard-telemetry monitor 3447
postcard-telemetry queue-profile 3448
postcard-telemetry system monitor 3449
postcard-telemetry watchlist ip 3450
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)c
Contents
Page 101
power efficient-ethernet auto 3451
power efficient-ethernet sleep threshold aggressive 3452
power inline 3453
power inline default_consumption 3454
power inline police action 3455
power inline port priority 3456
power redundancy-mode combined 3457
power redundancy-mode combined force 3458
power redundancy-mode insrc-redundant 3459
power redundancy-mode ps-redundant 3460
power reserve 3461
poweroff 3462
pps 3463
pps 3464
precision milliseconds 3465
preempt 3466
preempt 3467
preempt delay minimum 3468
preempt delay minimum reload sync preempt delay reload minimum sync preempt delay sync minimumreload preempt delay reload sync minimum preempt delay sync reload minimum preempt delayminimum sync reload preempt delay reload sync preempt delay sync reload preempt delay minimumsync preempt delay sync minimum preempt delay minimum reload preempt delay reload minimumpreempt delay minimum preempt delay reload preempt delay sync preempt 3469
preference 3471
preference max 3472
preference min 3473
prefix out 3474
priority-flow-control auto-restore multiplier 3475
priority-flow-control fixed-restore multiplier 3476
priority-flow-control inn-recover interface 3477
priority-flow-control mode 3478
priority-flow-control override-interface mode off 3479
priority-flow-control recover interface 3480
priority-flow-control tah-recover interface 3481
priority-flow-control watch-dog-interval on 3482
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)ci
Contents
Page 102
priority-flow-control watch-dog-interval on 3483
priority-flow-control watch-dog forced on 3484
priority-flow-control watch-dog interval 3485
priority-flow-control watch-dog shutdown-multiplier 3486
priority 3487
priority2 3488
priority 3489
priority 3490
priority 3491
priority 3492
priority 3493
priority 3494
private-vlan 3495
private-vlan association 3496
private-vlan mapping 3497
private-vlan synchronize 3498
probe-interval 3499
probe-interval 3500
probe 3501
probe 3502
probe 3503
probe 3504
probe 3505
probe 3506
probe 3507
probe get 3508
probe get 3509
probe get 3510
probe get 3511
probe host 3512
probe host 3513
probe host 3514
probe host 3515
probe host 3516
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cii
Contents
Page 103
probe host 3517
probe host 3518
probe port 3519
probe port 3520
probe port 3521
probe port 3522
probe port 3523
probe port 3524
probe port 3525
profile 3526
profile 3527
promiscuous-mode off 3528
propagate-sgt 3529
protection 3530
proto 3531
protocol-version 3532
protocol-version 3533
protocol 3534
protocol 3535
protocol shutdown 3536
protocol shutdown 3537
ptp 3538
ptp announce interval 3539
ptp announce timeout 3540
ptp clock-identity 3541
ptp clock-sync auto 3542
ptp clock one-step 3543
ptp convergence-time 3544
ptp correction-range 3545
ptp correction-range logging 3546
ptp correction hardware 3547
ptp cost 3548
ptp delay-request minimum interval 3549
ptp device-type boundary 3550
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)ciii
Contents
Page 104
ptp domain 3551
ptp domain 3552
ptp domain clock-accuracy-threshold 3553
ptp domain clock-class-threshold 3554
ptp domain priority 3555
ptp grandmaster-capable 3556
ptp mean-path-delay 3557
ptp multi-domain 3558
ptp multi-domain transition-attributes priority1 3559
ptp multi-domain transition-attributes priority2 3560
ptp multicast master-only 3561
ptp neighbor propagation-delay-threshold 3562
ptp offload 3563
ptp pdelay-req-interval 3564
ptp priority1 3565
ptp priority2 3566
ptp source 3567
ptp sync interval 3568
ptp transport ipv4 ucast master 3569
ptp transport ipv4 ucast slave 3570
ptp ucast-source 3571
ptp vlan 3572
purge module running-config 3573
push 3574
pwd 3575
python 3576
python instance 3577
Q Commands 3579C H A P T E R 1 8
qos copy policy-map type network-qos prefix 3580
qos copy policy-map type queuing prefix 3581
qos qos-policies statistics 3582
qos shared-policer 3583
qos statistics 3587
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)civ
Contents
Page 105
qualify udf 3588
queue-limit 3589
queue-limit2 3590
queue-limit3 3591
queue-limit4 3592
queue-limit5 3593
queue-limit bytes 3594
R Commands 3595C H A P T E R 1 9
radius-server deadtime 3600
radius-server directed-request 3601
radius-server host key 0 6 7 3602
radius-server host test 3604
radius-server key 0 6 7 3605
radius-server pss-clean 3606
radius-server retransmit 3607
radius-server test 3608
radius-server timeout 3609
random-detect 3610
random-detect2 minimum-threshold2 maximum-threshold2 3612
random-detect2 non-ecn minimum-threshold2 maximum-threshold2 drop 3613
random-detect 3614
random-detect cos-based 3616
rate-limit 3618
rate-limit cpu direction pps action log 3619
rate-limit cpu direction pps action log 3620
rate-limit packet_in burst 3621
rate-limit packet_in burst 3622
rate-mode 3623
rd auto 3624
rd auto 3625
receiver 3626
reconnect-interval 3627
record-route 3628
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cv
Contents
Page 106
record-route 3629
record 3630
record 3631
record 3632
record 3633
record 3634
redistribute bgp 3635
redistribute bgp eigrp isis ospf rip static direct amt lisp route-map 3636
redistribute filter route-map 3637
redistribute filter route-map 3638
redistribute maximum-prefix 3639
redistribute maximum-prefix 3640
redistribute maximum-prefix 3641
redistribute maximum-prefix 3642
redistribute maximum-prefix 3643
redistribute route-map 3644
redistribute route-map 3645
redistribute route-map 3646
redistribute route-map 3647
redistribute route-map 3648
redistribute route-map 3649
redistribute route-map 3650
redistribute route-map 3651
redistribute route-map 3652
redistribute route-map 3653
redownload forwarding state 3654
redundancy-group 3655
reference-bandwidth 3656
reference-bandwidth 3657
register-database-mapping 3658
register-route-notifications 3659
reload 3660
reload cancel 3661
reload in 3662
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cvi
Contents
Page 107
reload module 3663
reload module force-dnld 3664
reload non-interruptive 3665
reload power-cycle 3666
reload sync-adjacency 3667
reload sync-adjacency 3668
reload timer 3669
reload vdc 3670
reload vdc 3671
remark 3672
remark 3673
remark 3674
remote-as 3675
remote-span 3676
remote 3677
remove-private-as 3678
reoptimize events link-up 3679
replay-protection 3680
report 3681
report 3682
report 3683
report 3684
report 3685
report 3686
report 3687
report 3688
report 3689
report 3690
report 3691
report 3692
report 3693
report 3694
report 3695
report 3696
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cvii
Contents
Page 108
request-data-size 3697
request-data-size 3698
request-data-size 3699
resequence access 3700
reset 3701
reset 3702
reset 3703
reset 3704
reset 3705
reset 3706
reset 3707
reset 3708
reset 3709
reset 3710
reset 3711
reset 3712
reset 3713
reset 3714
reset 3715
reset 3716
restart amt 3717
restart bgp 3718
restart eigrp 3719
restart igmp 3720
restart isis 3721
restart msdp 3722
restart ospf 3723
restart ospfv3 3724
restart pim 3725
restart pim6 3726
restart rip 3727
restart rsvp 3728
resync-database 3729
retain route-target all 3730
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cviii
Contents
Page 109
retain route-target all 3731
retransmit-interval 3732
retransmit-interval 3733
retransmit-interval 3734
revision 3735
revocation-check crl 3736
rewrite-evpn-rt-asn 3737
rewrite-rt-asn 3738
rfc1583compatibility 3739
rip shutdown 3740
rmdir 3741
rmon alarm absolute rising-threshold falling-threshold 3742
rmon event 3743
rmon hcalarm absolute startupalarm rising-threshold falling-threshold owner 3744
roaming-eid-prefix 3745
role feature-group name 3746
role name 3747
role priority 3748
rollback running-config checkpoint 3749
root-priority 3750
route-map 3751
route-map 3752
route-map 3753
route-map 3754
route-map out 3755
route-map pbr-statistics 3756
route-reflector-client 3757
route-reflector-client 3758
route-target both auto 3759
route-target both auto 3760
route-target export 3761
route-target export auto 3762
route-target import 3763
route-target import auto 3764
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cix
Contents
Page 110
route delete dampen interval 3765
router-guard ip multicast 3766
router-guard ip multicast switchports 3767
router-id 3768
router-id 3769
router-id 3770
router-id 3771
router-id 3772
router-id 3773
router-preference maximum 3774
router bgp 3775
router eigrp 3776
router isis 3777
router ospf 3778
router ospfv3 3779
router rip 3780
routing-context vrf 3781
rsakeypair 3782
rtr etr eid 3783
rule 3784
rule command 3785
rule oid 3786
run-script 3787
run2 guestshell 3788
run bash 3789
S Commands 3791C H A P T E R 2 0
sak-expiry-time 3805
sampling-rate prepost 3806
sampling 3807
sap hash-algorithm HMAC-SHA-1 3808
sap modelist 3809
sap pmk sap pmk use-dot1x 3810
save 3811
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cx
Contents
Page 111
scale-factor module 3812
scheduler aaa-authentication 3813
scheduler enable 3814
scheduler job name 3815
scheduler logfile size 3816
scheduler schedule name 3817
scheduler transport email 3818
scripting tcl init 3819
scripting tcl recursion-limit 3820
section 3821
secure-handoff 3822
security-level 3823
security-policy 3824
sed 3825
send-community 3826
send-community 3827
send-community extended 3828
send-lifetime month_a month_b month_c month_d month_e month_f month_g month_h month_imonth_j month_kmonth_l duration infinite month_a month_bmonth_c month_dmonth_e month_fmonth_g month_h month_i month_j month_k month_l 3829
send-lifetime month_a month_b month_c month_d month_e month_f month_g month_h month_imonth_j month_kmonth_l duration infinite month_a month_bmonth_c month_dmonth_e month_fmonth_g month_h month_i month_j month_k month_l 3831
send 3833
send session 3834
sender 3835
sensor-group 3836
server 3837
server 3838
server 3839
server protocol ldap 3840
server protocol radius group 3841
server protocol xmpp ip 3842
service-policy-dynamic input 3843
service-policy 3844
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxi
Contents
Page 112
service-policy 3845
service-policy 3846
service-policy input 3847
service-policy type network-qos 3848
service-policy type qos 3849
service-policy type queuing 3850
service-policy type queuing 3851
service-policy type queuing 3852
service password-recovery 3853
service unsupported-transceiver 3854
session-limit 3855
session domain-lookup 3856
session protection 3857
set-attached-bit 3858
set-overload-bit 3859
set-overload-bit 3860
set 3861
set 3864
set 3865
set 3866
set 3867
set 3869
set as-path prepend last-as tag 3870
set comm-list delete 3871
set community none additive internet local-AS 3872
set cos 3873
set cos 3874
set dampening 3875
set distance 3876
set drpvec 3877
set drpvec 3883
set extcomm-list delete 3889
set extcommunity 4byteas-generic transitive additive 3890
set extcommunity color 3891
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxii
Contents
Page 113
set extcommunity cost 3892
set extcommunity rt additive 3893
set forwarding-address 3894
set ieth 3895
set ieth 3898
set inner arp 3901
set inner ipv4 3903
set inner ipv4 3905
set inner ipv4 3907
set inner ipv6 src_ip 3909
set inner l2 3910
set inner l2 3912
set inner l2 3914
set inner l2 hg2 3916
set inner l2 hg2 3918
set inner l4 3920
set inner l4 3921
set inner l4 3924
set interface 3925
set interval find-new-host 3926
set interval sync-full-info 3927
set ip address prefix-list 3928
set ip default next-hop 3929
set ip default next-hop verify-availability 3930
set ip next-hop 3931
set ip next-hop peer-address 3932
set ip next-hop redist-unchanged 3933
set ip next-hop unchanged 3934
set ip next-hop verify-availability 3935
set ip precedence 3936
set ipv6 address prefix-list 3937
set ipv6 default next-hop 3938
set ipv6 default next-hop verify-availability 3939
set ipv6 next-hop 3940
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxiii
Contents
Page 114
set ipv6 next-hop peer-address 3941
set ipv6 next-hop redist-unchanged 3942
set ipv6 next-hop unchanged 3943
set ipv6 next-hop verify-availability 3944
set ipv6 precedence 3945
set label-index 3946
set level level-1 level-1-2 level-2 3947
set local-preference 3948
set metric 3949
set nssa-only 3950
set origin egp 3951
set origin egp igp incomplete 3952
set outer arp 3953
set outer arp 3955
set outer fcoe 3957
set outer ipv4 3959
set outer ipv4 3961
set outer ipv4 3963
set outer ipv6 src_ip 3965
set outer ipv6 src_ip 3966
set outer l2 3967
set outer l2 3969
set outer l2 3971
set outer l2 hg2 3973
set outer l4 3975
set outer l4 3976
set outer l4 3979
set path-selection advertise 3982
set pktrw 3983
set pktrw 3990
set pktrw 3997
set sb_info 4003
set sb_info 4006
set sideband 4009
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxiv
Contents
Page 115
set sideband 4011
set sideband 4013
set sideband 4015
set stats 4018
set tag 4021
set weight 4022
setup 4023
sflow 4024
sflow 4025
sflow data-source interface 4026
sflow data-source interface 4027
sflow extended switch 4028
shape 4029
shared-secret 4031
shut 4032
shutdown 4033
shutdown 4034
shutdown 4035
shutdown 4036
shutdown 4037
shutdown 4038
shutdown 4039
shutdown 4040
shutdown 4041
shutdown 4042
shutdown 4043
shutdown 4044
shutdown 4045
shutdown 4046
shutdown 4047
shutdown 4048
shutdown 4049
shutdown 4050
shutdown 4051
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxv
Contents
Page 116
shutdown 4052
shutdown 4053
shutdown 4054
shutdown 4055
shutdown 4056
shutdown 4057
shutdown 4058
shutdown 4059
shutdown 4060
shutdown 4061
shutdown 4062
shutdown 4063
shutdown 4064
shutdown 4065
shutdown 4066
shutdown 4067
shutdown 4068
shutdown 4069
shutdown 4070
shutdown force 4071
shutdown lan 4072
shutdown lan 4073
signalling advertise explicit-null 4074
signalling hello graceful-restart 4075
signalling hello graceful-restart refresh interval 4076
signalling hello graceful-restart refresh misses 4077
signalling hello graceful-restart send recovery-time 4078
signalling hello graceful-restart send restart-time 4079
signalling hello reroute 4080
signalling initial-retransmit-delay 4081
signalling patherr state-removal 4082
signalling rate-limit 4083
signalling refresh interval 4084
signalling refresh misses 4085
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxvi
Contents
Page 117
signalling refresh reduction 4086
signalling refresh reduction ack-delay 4087
signalling refresh reduction bundle-max-size 4088
signing level 4089
site-id 4090
site-of-origin 4091
slave ipv4 4092
sleep 4093
sleep instance 4094
slot 4095
slot 4096
smart-channel 4097
smart-channel port-group 4098
smtp-host smtp-port reply-to from 4099
snapshot create 4100
snapshot delete 4101
snapshot delete ALL 4102
snapshot section add 4103
snapshot section delete 4104
snmp-server aaa-user cache-timeout 4105
snmp-server community 4106
snmp-server community 4107
snmp-server community use-acl 4108
snmp-server contact 4109
snmp-server context 4110
snmp-server counter cache enable 4111
snmp-server counter cache timeout 4112
snmp-server enable traps 4113
snmp-server enable traps bgp 4114
snmp-server enable traps bgp cbgp2 4115
snmp-server enable traps bgp cbgp2 threshold prefix 4116
snmp-server enable traps bgp threshold prefix 4117
snmp-server enable traps eigrp 4118
snmp-server enable traps ospf 4119
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxvii
Contents
Page 118
snmp-server enable traps ospf lsa 4120
snmp-server enable traps ospf rate-limit 4121
snmp-server enable traps ospfv3 4122
snmp-server enable traps ospfv3 lsa 4123
snmp-server enable traps ospfv3 lsa 4124
snmp-server enable traps ospfv3 rate-limit 4125
snmp-server enable traps storm-control trap-rate 4126
snmp-server engineID local 4127
snmp-server force-unload-feature 4128
snmp-server globalEnforcePriv 4129
snmp-server host 4130
snmp-server host filter-vrf 4131
snmp-server host source 4132
snmp-server host use-vrf 4133
snmp-server host use_vrf 4134
snmp-server load-cond-feature 4135
snmp-server load-mib 4136
snmp-server location 4137
snmp-server mib community-map context 4138
snmp-server protocol enable 4139
snmp-server source-interface informs 4140
snmp-server source-interface traps 4141
snmp-server system-shutdown 4142
snmp-server tcp-session 4143
snmp-server user 4144
snmp-server user 4145
snmp ifmib ifalias long 4147
snmp trap link-status 4148
snmp trap link-status 4149
snmp trap link-status 4150
snmp trap link-status 4151
snmp trap link-status 4152
snmp trap link-status 4153
snsr-grp sample-interval 4154
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxviii
Contents
Page 119
sockets local-port-range 4155
soft-reconfiguration inbound 4156
soft-reconfiguration inbound 4157
soo auto 4158
sort 4159
source-address ipv4 4160
source-group 4161
source-interface 4162
source-interface 4163
source-interface 4164
source-interface 4165
source-interface 4166
source-interface 4167
source-interface hold-down-time 4168
source 4169
source 4170
source 4171
source 4172
source 4173
source 4174
source 4175
source 4176
source 4177
source 4178
source 4179
source copy-sys 4180
source filter ip 4181
source filter ip any any 4182
source forward-drops 4183
source group permit 4184
source interface 4185
source interface 4186
source ip 4187
source vlan 4188
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxix
Contents
Page 120
spanning-tree bpdufilter 4189
spanning-tree bpduguard 4190
spanning-tree bridge-domain 4191
spanning-tree bridge assurance 4192
spanning-tree cost 4193
spanning-tree cost auto 4194
spanning-tree domain 4195
spanning-tree domain clear statistics 4196
spanning-tree fcoe 4197
spanning-tree guard 4198
spanning-tree lc-issu 4199
spanning-tree lc-issu 4200
spanning-tree link-type 4201
spanning-tree loopguard default 4202
spanning-tree mode 4203
spanning-tree mst configuration 4204
spanning-tree mst configuration 4205
spanning-tree mst cost 4206
spanning-tree mst cost auto 4207
spanning-tree mst forward-time 4208
spanning-tree mst hello-time 4209
spanning-tree mst max-age 4210
spanning-tree mst max-hops 4211
spanning-tree mst port-priority 4212
spanning-tree mst pre-standard 4213
spanning-tree mst priority 4214
spanning-tree mst root 4215
spanning-tree mst simulate pvst 4216
spanning-tree mst simulate pvst global 4217
spanning-tree pathcost method 4218
spanning-tree port-priority 4219
spanning-tree port type 4220
spanning-tree port type edge bpdufilter default 4221
spanning-tree port type edge bpduguard default 4222
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxx
Contents
Page 121
spanning-tree port type edge default 4223
spanning-tree port type edge trunk 4224
spanning-tree port type network default 4225
spanning-tree pseudo-information 4226
spanning-tree vlan 4227
spanning-tree vlan forward-time 4228
spanning-tree vlan hello-time 4229
spanning-tree vlan max-age 4230
spanning-tree vlan priority 4231
spanning-tree vlan root 4232
speed-group 4233
speed 4234
speed 4235
speed 4236
speed 4237
speed 4238
speed 4239
speed 4240
speed 4241
speed auto 4242
speed auto 100 4243
speed auto 100 1000 4244
speed auto 100 1000 4245
speed auto 100 4246
speed auto 4247
spf-interval 4248
spf-interval 4249
spf-interval 4250
spf mode incremental 4251
sport 4252
sport 4253
src-intf 4254
ssh 4255
ssh6 4256
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxi
Contents
Page 122
ssh all 4257
ssh cipher-mode weak 4258
ssh idle 4259
ssh key 4260
ssh login-attempts 4261
ssh login-gracetime 4262
ssh port 4263
ssh rekey max-data max-time 4264
ssh server enable 4265
ssx exporter 4266
ssx monitor 4267
ssx record 4268
ssx system monitor 4269
ssx system system-id 4270
standby 4271
standby ip 4272
start-threshold 4273
start 4274
start 4275
start 4276
start 4277
start 4278
start 4279
start 4280
start 4281
start 4282
start 4283
start 4284
start 4285
start 4286
start 4287
start 4288
start 4289
state 4290
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxii
Contents
Page 123
state enabled 4291
statistics 4292
statistics 4293
statistics 4294
statistics collection-interval 4295
statistics per-entry 4296
statistics per-entry 4297
statistics per-entry 4298
statistics per-entry 4299
stats-reporting-period 4300
status 4301
status 4302
status 4303
status 4304
status 4305
status 4306
status 4307
stop-threshold 4308
stopbits 4309
stopbits 1 4310
storm-control-cpu 4311
storm-control 4312
streetaddress 4313
stub 4314
sub-switch vlan 4315
subscription 4316
summary-address 4317
summary-address 4318
summary-address 4319
summary-address 4320
suppress-arp 4321
suppress-fib-pending 4322
suppress-fib-pending 4323
suppress-inactive 4324
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxiii
Contents
Page 124
suppress-inactive 4325
suppress-signaling-protocol ldp 4326
suppress mac-route 4327
switch-id 4328
switch-priority 4329
switch-profile 4330
switch-profile 4331
switch-role border-leaf 4332
switch-scope controller 4333
switch pipeline 4334
switchback 4335
switching-mode fabric-speed 40g 4336
switching-mode fast-to-slow-speed-cut-through 4337
switching-mode store-forward 4338
switchport 4339
switchport 4340
switchport access vlan 4341
switchport access vlan 4342
switchport access vlan 4343
switchport autostate exclude 4344
switchport backup interface 4345
switchport backup interface 4346
switchport backup interface multicast fast-convergence 4347
switchport backup interface multicast fast-convergence 4348
switchport backup interface preemption delay 4349
switchport backup interface preemption delay 4350
switchport backup interface preemption mode 4351
switchport backup interface preemption mode 4352
switchport beacon 4353
switchport block unicast 4354
switchport description 4355
switchport dot1q ethertype 4356
switchport dot1q ethertype 4357
switchport duplex 4358
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxiv
Contents
Page 125
switchport host 4359
switchport ignore bit-errors 4360
switchport isolated 4361
switchport mac-learn disable 4362
switchport mode 4363
switchport mode 4364
switchport mode 4365
switchport mode 4366
switchport mode 4367
switchport mode 4368
switchport mode monitor buffer-limit 4369
switchport mode private-vlan 4370
switchport mode private-vlan trunk 4371
switchport monitor 4372
switchport mtu 4373
switchport owner 4374
switchport port-security 4375
switchport port-security aging time 4376
switchport port-security aging type absolute 4377
switchport port-security mac-address 4378
switchport port-security mac-address sticky 4379
switchport port-security maximum 4380
switchport port-security violation 4381
switchport priority extend cos 4382
switchport private-vlan association trunk 4383
switchport private-vlan host-association 4384
switchport private-vlan mapping 4385
switchport private-vlan mapping trunk 4386
switchport private-vlan trunk allowed vlan 4387
switchport private-vlan trunk native vlan 4388
switchport promiscuous-mode off 4389
switchport speed 4390
switchport speed 4391
switchport trunk allow-multi-tag 4392
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxv
Contents
Page 126
switchport trunk allowed vlan 4393
switchport trunk allowed vsan 4394
switchport trunk allowed vsan 4395
switchport trunk mode 4396
switchport trunk mode 4397
switchport trunk native vlan 4398
switchport trunk pruning vlan except add remove none all 4399
switchport virtual-ethernet-bridge 4400
switchport vlan mapping 4401
switchport vlan mapping all 4402
switchport vlan mapping all dot1q-tunnel 4403
switchport vlan mapping all dot1q-tunnel 4404
switchport vlan mapping dot1q-tunnel 4405
switchport vlan mapping dot1q-tunnel allowed-vlan 4406
switchport vlan mapping enable 4407
switchport voice vlan 4408
switchport voice vlan 4409
switchto vdc 4410
sync-peers destination 4411
sync-snmp-password 4412
sync-snmp-password 4413
sync-snmp-password 4414
system-mac 4415
system-mac 4416
system-priority 4417
system 4418
system 4419
system acl 4421
system auto-collect tech-support 4422
system cores 4423
system default interface-vlan autostate 4424
system default interface 4425
system default interface 4426
system default switchport 4427
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxvi
Contents
Page 127
system default switchport shutdown 4428
system default tx-credit double-queue 4429
system dot1q-tunnel transit 4430
system fabric-mode full-rate 4431
system fabric core-vlans 4432
system fabric dynamic-vlans 4433
system fast-reload stabilization-timer 4434
system hap-reset 4435
system hap-reset 4436
system health check bootflash 4437
system heartbeat 4438
system heartbeat 4439
system high-multicast-priority 4440
system inband queuing 4441
system inband queuing 4442
system interface shutdown 4443
system jumbomtu 4444
system kgdb 4445
system kgdb 4446
system login block-for 4447
system login block-for attempts within 4448
system login quiet-mode 4449
system login quiet-mode access-class 4450
system memory-thresholds minor severe critical 4451
system mode maintenance 4452
system mode maintenance always-use-custom-profile 4453
system mode maintenance maint-delay 4454
system mode maintenance on-reload reset-reason 4455
system mode maintenance snapshot-delay 4456
system mode maintenance timeout 4457
system module emon-enhanced 4458
system module failure-action shutdown 4459
system mrouting 4460
system poap 4461
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxvii
Contents
Page 128
system poap 4462
system pss shrink 4463
system qos 4464
system routing unknown-unicast-flood 4465
system security compliance common-criteria 4466
system shutdown fan-direction mismatch 4467
system simulate fan-presence 4468
system standby manual-boot 4469
system standby manual-boot 4470
system startup-config init 4471
system startup-config unlock 4472
system statistics 4473
system statistics 4474
system switch-mode 4475
system switchover 4476
system switchover force 4477
system timeout 4478
system trace 4479
system urpf disable 4480
system vlan long-name 4481
system vlan reserve 4482
system vrf-member-change retain-l3-config 4483
system watchdog 4484
system watchdog 4485
system watchdog kgdb 4486
system watchdog kgdb 4487
T Commands 4489C H A P T E R 2 1
table-map 4496
table-map 4497
table-map 4498
table-map 4499
table-map 4500
table-map 4501
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxviii
Contents
Page 129
table-map 4502
table-map 4503
tac-pac 4504
tac-pac 4505
tacacs-server deadtime 4506
tacacs-server directed-request 4507
tacacs-server host key 0 6 7 4508
tacacs-server host test 4509
tacacs-server key 0 6 7 4510
tacacs-server test 4511
tacacs-server timeout 4512
tacacs enable 4513
tag 4514
tag happens in 4515
tahoe-python module 4516
tahoe-python module quoted 4517
tail 4518
tail 4519
tar 4520
tclsh 4521
tclsh 4522
tcp-connect 4523
telnet 4524
telnet6 4525
telnet login-attempts 4526
telnet server enable 4527
template 4528
template data timeout 4529
template peer-policy 4530
template peer-session 4531
template peer 4532
terminal 4533
terminal alias 4534
terminal ask-on-term 4535
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxix
Contents
Page 130
terminal color 4536
terminal context management 4537
terminal deep-help 4538
terminal dont-ask 4539
terminal edit-mode vi 4540
terminal event-manager bypass 4541
terminal history no-exec-in-config 4542
terminal history no-exec-in-config 4543
terminal history no-exec-in-config 4544
terminal home 4545
terminal length 4546
terminal length 4547
terminal log-all 4548
terminal no 4549
terminal output xml 4550
terminal output xml 4551
terminal output xml 4552
terminal password 4553
terminal prompt 4554
terminal redirection-mode 4555
terminal session-timeout 4556
terminal sticky-mode 4557
terminal terminal-type 4558
terminal time 4559
terminal tree-update 4560
terminal verify-only 4561
terminal width 4562
terminal width 4563
threshold-percent 4564
threshold 4565
time-range 4566
timeout 4567
timeout 4568
timeout 4569
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxx
Contents
Page 131
timer 4570
timer 4571
timer inactivity 4572
timers 4573
timers 4574
timers 4575
timers advertise 4576
timers basic 4577
timers bestpath-defer maximum 4578
timers bestpath-limit 4579
timers bgp 4580
timers lsa-arrival 4581
timers lsa-arrival 4582
timers lsa-group-pacing 4583
timers lsa-group-pacing 4584
timers prefix-peer-timeout 4585
timers prefix-peer-wait 4586
timers srgb cleanup 4587
timers srgb retry 4588
timers throttle lsa 4589
timers throttle lsa 4590
timers throttle spf 4591
timers throttle spf 4592
timestamp timestamp 4593
tls trust-point local remote 4594
tls trust-point local remote 4595
topology 4596
topology holddown sigerr 4597
tos 4598
tr 4599
trace buffer size 4600
traceroute 4601
traceroute6 4602
track-adjacency-nexthop 4603
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxxi
Contents
Page 132
track 4604
track 4605
track 4606
track 4607
track 4608
track 4609
track 4610
track 4611
track 4612
track 4613
track data 4614
track interface 4615
track interface priority 4616
track running-state track startup-state 4617
tracking enable 4618
traffic-class 4619
traffic-engineering 4620
transmit-delay 4621
transmit-delay 4622
transmit-delay 4623
transport connection-mode passive 4624
transport email 4625
transport email mail-server 4626
transport http proxy enable 4627
transport http proxy server 4628
transport http use-vrf 4629
transport udp 4630
transport udp 4631
transport udp 4632
transport udp source-port 4633
trigger forwarding distribution module 4634
trigger init 4635
trigger init in-select 10 4636
trigger init in-select 10 out-select 0 4637
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxxii
Contents
Page 133
trigger init in-select 10 out-select 1 4638
trigger init in-select 10 out-select 2 4639
trigger init in-select 19 4640
trigger init in-select 19 out-select 0 4641
trigger init in-select 19 out-select 1 4642
trigger init in-select 19 out-select 2 4643
trigger init in-select 6 4644
trigger init in-select 6 out-select 0 4645
trigger init in-select 6 out-select 1 4646
trigger init in-select 6 out-select 2 4647
trigger init in-select 7 4648
trigger init in-select 7 out-select 0 4649
trigger init in-select 7 out-select 1 4650
trigger init in-select 7 out-select 2 4651
trigger init in-select 8 4652
trigger init in-select 8 out-select 0 4653
trigger init in-select 8 out-select 1 4654
trigger init in-select 8 out-select 2 4655
trigger init in-select 9 4656
trigger init in-select 9 out-select 0 4657
trigger init in-select 9 out-select 1 4658
trigger init in-select 9 out-select 2 4659
trigger init ingress in-select 3 out-select 0 4660
trigger init ingress in-select 3 out-select 03 4661
trigger init ingress in-select 3 out-select 0 reverse 4662
trigger init ingress in-select 3 out-select 1 4663
trigger init ingress in-select 3 out-select 2 4664
trigger init ingress in-select 3 out-select 4 4665
trigger init ingress in-select 3 out-select 5 4666
trigger init ingress in-select 3 out-select 5 reverse 4667
trigger init ingress in-select 4 out-select 0 4668
trigger init ingress in-select 4 out-select 04 4669
trigger init ingress in-select 4 out-select 0 reverse 4670
trigger init ingress in-select 4 out-select 1 4671
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxxiii
Contents
Page 134
trigger init ingress in-select 4 out-select 2 4672
trigger init ingress in-select 4 out-select 3 4673
trigger init ingress in-select 4 out-select 5 4674
trigger init ingress in-select 4 out-select 5 reverse 4675
trigger init ingress in-select 5 out-select 0 4676
trigger init ingress in-select 5 out-select 05 4677
trigger init ingress in-select 5 out-select 05 reverse 4678
trigger init ingress in-select 5 out-select 0 reverse 4679
trigger init ingress in-select 5 out-select 1 4680
trigger init ingress in-select 5 out-select 2 4681
trigger init ingress in-select 5 out-select 3 4682
trigger init ingress in-select 5 out-select 4 4683
trigger init ingress in-select 6 out-select 0 4684
trigger init ingress in-select 6 out-select 0 reverse 4685
trigger init ingress in-select 6 out-select 1 4686
trigger init ingress in-select 6 out-select 2 4687
trigger init ingress in-select 6 out-select 3 4688
trigger init ingress in-select 6 out-select 4 4689
trigger init ingress in-select 6 out-select 5 4690
trigger init ingress in-select 6 out-select 5 reverse 4691
trigger init ingress in-select 7 out-select 0 4692
trigger init ingress in-select 7 out-select 0 reverse 4693
trigger init ingress in-select 7 out-select 1 4694
trigger init ingress in-select 7 out-select 2 4695
trigger init ingress in-select 7 out-select 3 4696
trigger init ingress in-select 7 out-select 4 4697
trigger init ingress in-select 7 out-select 5 4698
trigger init ingress in-select 7 out-select 5 reverse 4699
trigger init lu-a2d 0 4700
trigger init lu-a2d 0 in-select 10 out-select 0 4701
trigger init lu-a2d 0 in-select 10 out-select 1 4702
trigger init lu-a2d 0 in-select 10 out-select 2 4703
trigger init lu-a2d 0 in-select 19 out-select 0 4704
trigger init lu-a2d 0 in-select 19 out-select 1 4705
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxxiv
Contents
Page 135
trigger init lu-a2d 0 in-select 19 out-select 2 4706
trigger init lu-a2d 0 in-select 6 out-select 0 4707
trigger init lu-a2d 0 in-select 6 out-select 1 4708
trigger init lu-a2d 0 in-select 6 out-select 2 4709
trigger init lu-a2d 0 in-select 7 out-select 0 4710
trigger init lu-a2d 0 in-select 7 out-select 1 4711
trigger init lu-a2d 0 in-select 7 out-select 2 4712
trigger init lu-a2d 0 in-select 8 out-select 0 4713
trigger init lu-a2d 0 in-select 8 out-select 1 4714
trigger init lu-a2d 0 in-select 8 out-select 2 4715
trigger init lu-a2d 0 in-select 9 out-select 0 4716
trigger init lu-a2d 0 in-select 9 out-select 1 4717
trigger init lu-a2d 0 in-select 9 out-select 2 4718
trigger init lu-a2d 0 out-select 0 4719
trigger init lu-a2d 0 out-select 1 4720
trigger init lu-a2d 0 out-select 2 4721
trigger init lu-a2d 1 4722
trigger init lu-a2d 1 in-select 10 4723
trigger init lu-a2d 1 in-select 10 out-select 0 4724
trigger init lu-a2d 1 in-select 10 out-select 1 4725
trigger init lu-a2d 1 in-select 10 out-select 2 4726
trigger init lu-a2d 1 in-select 19 4727
trigger init lu-a2d 1 in-select 19 out-select 0 4728
trigger init lu-a2d 1 in-select 19 out-select 1 4729
trigger init lu-a2d 1 in-select 19 out-select 2 4730
trigger init lu-a2d 1 in-select 6 4731
trigger init lu-a2d 1 in-select 6 out-select 0 4732
trigger init lu-a2d 1 in-select 6 out-select 1 4733
trigger init lu-a2d 1 in-select 6 out-select 2 4734
trigger init lu-a2d 1 in-select 7 4735
trigger init lu-a2d 1 in-select 7 out-select 0 4736
trigger init lu-a2d 1 in-select 7 out-select 1 4737
trigger init lu-a2d 1 in-select 7 out-select 2 4738
trigger init lu-a2d 1 in-select 8 4739
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxxv
Contents
Page 136
trigger init lu-a2d 1 in-select 8 out-select 0 4740
trigger init lu-a2d 1 in-select 8 out-select 1 4741
trigger init lu-a2d 1 in-select 8 out-select 2 4742
trigger init lu-a2d 1 in-select 9 4743
trigger init lu-a2d 1 in-select 9 out-select 0 4744
trigger init lu-a2d 1 in-select 9 out-select 1 4745
trigger init lu-a2d 1 in-select 9 out-select 2 4746
trigger init out-select 0 4747
trigger init out-select 1 4748
trigger init out-select 2 4749
trigger reset 4750
trigger route download vrf ipv4 4751
trunk protocol 4752
trusted-port 4753
trusted-port 4754
trusted-port 4755
ttag-marker-interval 4756
ttag-marker-interval 4757
ttag-marker enable 4758
ttag-marker enable 4759
ttag-strip 4760
ttag 4761
ttag 4762
ttl-security hops 4763
tunnel destination 4764
tunnel mode 4765
tunnel path-mtu-discovery 4766
tunnel path-mtu-discovery age-timer 4767
tunnel path-mtu-discovery min-mtu 4768
tunnel source 4769
tunnel ttl 4770
tunnel use-vrf 4771
U Commands 4773C H A P T E R 2 2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxxvi
Contents
Page 137
udf 4775
udld aggressive 4776
udld aggressive 4777
udld aggressive 4778
udld aggressive 4779
udld continue-on-err 4780
udld disable 4781
udld disable 4782
udld enable 4783
udld enable 4784
udld message-time 4785
udld reset 4786
udp-echo 4787
udp-jitter 4788
undebug all 4790
undebug l2rib 4791
uniq 4792
unmount 4793
unmount slot0 4794
unsuppress-map 4795
untagged cos 4796
update-source 4797
update-source 4798
update license 4799
update license 4800
urib debugs-dump-to-file 4801
use-chunking size 4802
use-compression gzip 4803
use-retry size 4804
use-vrf 4805
use-vrf 4806
use-vrf 4807
use-vrf 4808
user-jid password 4809
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxxvii
Contents
Page 138
user max-logins 4810
user max-logins 4811
username 4812
username 4813
username 4814
username 4815
username 4816
username keypair export 4817
username keypair generate 4818
username keypair import 4819
username password 4820
username ssh-cert-dn dsa 4821
username sshkey 4822
userpassphrase 4823
userpassphrase min 4824
userpassphrase min 4825
userprofile trustedCert CRLLookup user-switch-bind user-certdn-match user-pubkey-matchattribute-name search-filter base-DN 4826
V Commands 4827C H A P T E R 2 3
validate-json 4830
validate-xml 4831
validate-xml 4832
vdc 4833
vdc 4834
vdc combined-hostname 4835
vdc_id 4836
vdc resource template 4837
vdc suspend 4838
vdc suspend 4839
vdp dot1q default static 4840
vdp dot1q static 4841
vdp vni default static 4842
vdp vni static 4843
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxxviii
Contents
Page 139
verify-data 4844
verify-host 4845
verify 4846
verify profile 4847
verify verbose 4848
version 4849
version 9 4850
virtual-service 4851
virtual-service 4852
virtual-service 4853
virtual-service move name log to 4854
virtual-service reset force 4855
virtual IPv6 4856
virtual IPv6 4857
virtual ip 4858
virtual ip 4859
vlan-consistency-check 4860
vlan-pruning enable 4861
vlan 4862
vlan2 4863
vlan 4864
vlan 4865
vlan access-map 4866
vlan configuration 4867
vlan designated priority 4868
vlan filter vlan 4869
vlan root priority 4870
vmtracker connection 4871
vmtracker connection refresh 4872
vmtracker enable 4873
vmtracker fabric auto-config 4874
vn-segment 4875
vni 4876
vni 4877
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxxxix
Contents
Page 140
vni 4878
vni default dynamic 4879
vni l2 4880
vpc 4881
vpc domain 4882
vpc orphan-port suspend 4883
vpc peer-link 4884
vpc role preempt 4885
vpn 4886
vpn id 4887
vrf 4888
vrf 4889
vrf 4890
vrf 4891
vrf 4892
vrf 4893
vrf 4894
vrf 4895
vrf 4896
vrf 4897
vrf 4898
vrf 4899
vrf 4900
vrf context 4901
vrf default static 4902
vrf member 4903
vrf member 4904
vrf static 4905
vrrp 4906
vrrp bfd 4907
vrrpv2 4908
vrrpv3 4909
vrrpv3 address-family 4910
vrrpv3 address-family 4911
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxl
Contents
Page 141
vrrs leader 4912
vrrs pathway 4913
vsh 4914
vtp 4915
vtp domain 4916
vtp file 4917
vtp mode 4918
vtp password 4919
vtp pruning 4920
vtp version 4921
WCommands 4923C H A P T E R 2 4
wait-igp-convergence 4924
watch 4925
watch service action apply-acl 4926
watchlist 4927
watchlist 4928
wc 4929
wedge bmc ip-addr 4930
weight 4931
weight 4932
weight 4933
weight 4934
where 4935
where detail 4936
window-size 4937
wred-queue qos-group-map queue-only 4938
write erase 4939
write erase boot 4940
write erase debug 4941
write erase poap 4942
wrr-queue qos-group-map 4943
wrr unicast-bandwidth 4944
wwn vsan vsan-wwn 4945
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxli
Contents
Page 142
X Commands 4947C H A P T E R 2 5
xconnect 4948
xml 4949
xml 4950
xml server max-session 4951
xml server rm-shm 4952
xml server terminate session 4953
xml server timeout 4954
xml server validate 4955
xml server xml-debug 4956
xmlagent 4957
xmlin 4958
xmlin 4959
xmlin 4960
xmlin 4961
xmlout 4962
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxlii
Contents
Page 143
Preface
This preface includes the following sections:
• Audience, on page cxliii• Documentation Conventions, on page cxliii• Documentation Feedback, on page cxliv• Communications, Services, and Additional Information, on page cxliv
AudienceThis publication is for network administrators who install, configure, and maintain Cisco Nexus switches.
Documentation ConventionsCommand descriptions use the following conventions:
DescriptionConventionBold text indicates the commands and keywords that you enter literallyas shown.
bold
Italic text indicates arguments for which the user supplies the values.Italic
Square brackets enclose an optional element (keyword or argument).[x]
Square brackets enclosing keywords or arguments separated by a verticalbar indicate an optional choice.
[x | y]
Braces enclosing keywords or arguments separated by a vertical barindicate a required choice.
{x | y}
Nested set of square brackets or braces indicate optional or requiredchoices within optional or required elements. Braces and a vertical barwithin square brackets indicate a required choice within an optionalelement.
[x {y | z}]
Indicates a variable for which you supply values, in context where italicscannot be used.
variable
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxliii
Page 144
DescriptionConvention
A nonquoted set of characters. Do not use quotation marks around thestring or the string will include the quotation marks.
string
Examples use the following conventions:
DescriptionConventionTerminal sessions and information the switch displays are in screen font.screen font
Information you must enter is in boldface screen font.boldface screen font
Arguments for which you supply values are in italic screen font.italic screen font
Nonprinting characters, such as passwords, are in angle brackets.< >
Default responses to system prompts are in square brackets.[ ]
An exclamation point (!) or a pound sign (#) at the beginning of a lineof code indicates a comment line.
!, #
Documentation FeedbackTo provide technical feedback on this document, or to report an error or omission, please send your commentsto . We appreciate your feedback.
Communications, Services, and Additional Information• To receive timely, relevant information from Cisco, sign up at Cisco Profile Manager.
• To get the business impact you’re looking for with the technologies that matter, visit Cisco Services.
• To submit a service request, visit Cisco Support.
• To discover and browse secure, validated enterprise-class apps, products, solutions and services, visitCisco Marketplace.
• To obtain general networking, training, and certification titles, visit Cisco Press.
• To find warranty information for a specific product or product family, access Cisco Warranty Finder.
Cisco Bug Search Tool
Cisco Bug Search Tool (BST) is a web-based tool that acts as a gateway to the Cisco bug tracking systemthat maintains a comprehensive list of defects and vulnerabilities in Cisco products and software. BST providesyou with detailed defect information about your products and software.
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)cxliv
PrefaceDocumentation Feedback
Page 145
Notice
• Notice, on page 2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1
Page 146
Notice
This document should be used only as a glossary reference for possible commands. The listing of a commandin this document does not guarantee that the command is available or supported for your platform or application.
The command information in this reference document is auto-generated from the NX-OS source code. Whilewe attempt to manually remove unsupported, deprecated, or internal-use commands, such commands mayoccasionally appear in this document. Also, with the large variety of hardware platform combinations usingNX-OS software, some listed commands may not be applicable or recommended for a specific platform.Platform-based dependency information is not provided in this command reference.
We strongly encourage you to refer to the configuration guides for appropriate commands to configure andoperate a feature. Command limitations, restrictions, and recommendations are documented only in theconfiguration guides. When in doubt, please consult your Cisco representative.
Warning
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2
NoticeNotice
Page 147
A Commands
• aaa accounting default, on page 8• aaa accounting dot1x default group, on page 9• aaa authentication dot1x default group, on page 10• aaa authentication login ascii-authentication, on page 11• aaa authentication login console, on page 12• aaa authentication login default, on page 14• aaa authentication login default fallback error local, on page 16• aaa authentication login enable, on page 17• aaa authentication login error-enable, on page 18• aaa authentication login invalid-username-log, on page 19• aaa authentication login password-aging enable, on page 20• aaa authentication rejected, on page 21• aaa authentication rejected in ban, on page 22• aaa authorization commands console, on page 23• aaa authorization commands default, on page 24• aaa authorization ssh default group, on page 25• aaa bypass-user, on page 26• aaa group server ldap, on page 27• aaa group server radius, on page 28• aaa group server tacacs, on page 29• aaa test-authentication, on page 30• aaa test-radius-authentication, on page 31• aaa user default-role, on page 32• abort, on page 33• abort, on page 34• abort, on page 35• abort, on page 36• absolute-timeout, on page 37• absolute start, on page 38• accept-lifetime month_a month_b month_c month_d month_e month_f month_g month_h month_imonth_j month_k month_l duration infinite month_a month_b month_c month_d month_e month_fmonth_g month_h month_i month_j month_k month_l, on page 39
• access-class, on page 41• access-list, on page 42
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3
Page 148
• access-list, on page 43• access-list ipv6, on page 44• access vlan, on page 45• acllog match-log-level, on page 46• action, on page 47• action, on page 48• action cli, on page 49• action counter name value op, on page 50• action eem test, on page 51• action event-default, on page 52• action forceshut reset-reason, on page 53• action overbudgetshut, on page 54• action policy-default, on page 55• action reload, on page 56• action snmp-trap, on page 57• action syslog msg, on page 58• additional-paths install backup, on page 59• additional-paths receive, on page 60• additional-paths selection route-map, on page 61• additional-paths send, on page 62• address-family ipv4, on page 63• address-family ipv4 labeled-unicast, on page 64• address-family ipv4 labeled-unicast, on page 65• address-family ipv4 mdt, on page 66• address-family ipv4 mdt, on page 67• address-family ipv4 mvpn, on page 68• address-family ipv4 mvpn, on page 69• address-family ipv6, on page 70• address-family ipv6 labeled-unicast, on page 71• address-family ipv6 labeled-unicast, on page 72• address-family ipv6 mvpn, on page 73• address-family ipv6 mvpn, on page 74• address-family l2vpn evpn, on page 75• address-family l2vpn evpn, on page 76• address-family l2vpn vpls, on page 77• address-family l2vpn vpls, on page 78• address-family link-state, on page 79• address-family link-state, on page 80• address-family vpnv4 unicast, on page 81• address-family vpnv4 unicast, on page 82• address-family vpnv6 unicast, on page 83• address-family vpnv6 unicast, on page 84• address, on page 85• address, on page 86• address, on page 87• address, on page 88
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4
A Commands
Page 149
• address, on page 89• address, on page 90• address port-number, on page 91• address primary, on page 92• address secondary, on page 93• address secondary, on page 94• adjacency-check, on page 95• adjacency-resolve, on page 96• advertise-gw-ip, on page 97• advertise-labels, on page 98• advertise-map exist default advertise-map, on page 99• advertise-pip, on page 100• advertise-system-mac, on page 101• advertise evpn multicast, on page 102• advertise interface, on page 103• advertise l2vpn evpn, on page 104• advertise local-labeled-route, on page 105• advertise virtual-rmac, on page 106• advertisement-interval, on page 107• advertisement-interval, on page 108• afd queue-desired, on page 109• affinity-group, on page 110• affinity-group activate, on page 111• affinity, on page 112• affinity, on page 113• age, on page 114• age, on page 115• aggregate-address, on page 116• aggregate-address, on page 117• alert-group user-def-cmd, on page 118• allocate-label all, on page 119• allocate-label option-b, on page 120• allocate1 interface2, on page 121• allocate2 fcoe-vlan-range, on page 122• allocate3 shared interface3, on page 123• allow-vni-in-ethertag, on page 124• allow feature-set, on page 125• allowas-in, on page 126• allowas-in, on page 127• allowed-locators, on page 128• allowed-vlans, on page 129• amt flush-routes, on page 130• amt pseudo-interface, on page 131• analytics cluster, on page 132• anonymous-id, on page 133• append-after next, on page 134
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)5
A Commands
Page 150
• apply profile, on page 135• area authentication, on page 136• area authentication, on page 137• area default-cost, on page 138• area default-cost, on page 139• area filter-list route-map in, on page 140• area filter-list route-map in, on page 141• area nssa, on page 142• area nssa, on page 143• area nssa translate type7 always never supress-fa, on page 144• area nssa translate type7 always never supress-fa, on page 145• area range, on page 146• area range, on page 147• area sham-link, on page 148• area stub, on page 149• area stub, on page 150• area virtual-link, on page 151• area virtual-link, on page 152• area virtual-link, on page 153• area virtual-link, on page 154• arp access-list, on page 155• as-format asdot, on page 156• as-override, on page 157• assign interface shared, on page 158• assign vlan dedicated, on page 159• assign vrf prefix number dedicated, on page 160• attach console module, on page 161• attach module, on page 162• attach module node, on page 163• attach module port, on page 164• auth-mechanism plain, on page 165• authentication-check, on page 166• authentication-check, on page 167• authentication-check level-1, on page 168• authentication-check level-2, on page 169• authentication-key, on page 170• authentication-key, on page 171• authentication-key, on page 172• authentication-type cleartext, on page 173• authentication-type cleartext, on page 174• authentication-type cleartext, on page 175• authentication, on page 176• authentication, on page 177• authentication, on page 178• authentication, on page 179• authentication, on page 180
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)6
A Commands
Page 151
• authentication, on page 181• authentication bind, on page 182• authentication challenge, on page 183• authentication key-chain, on page 184• authentication key-chain, on page 185• authentication key-chain, on page 186• authentication key-chain, on page 187• authentication key-chain, on page 188• authentication key-chain, on page 189• authentication lifetime, on page 190• authentication text, on page 191• authentication type md5, on page 192• authentication window-size, on page 193• auto-bw, on page 194• auto-bw, on page 195• auto-bw timers frequency, on page 196• auto-cost reference-bandwidth, on page 197• auto-cost reference-bandwidth, on page 198• auto-recovery, on page 199• auto-remap-replication-servers, on page 200• autonomous-system, on page 201• autoroute announce, on page 202• autoroute metric, on page 203• autostate, on page 204• autovlan enable, on page 205• awk, on page 206
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)7
A Commands
Page 152
aaa accounting default[no] aaa accounting default { group <s0> [ <s1> [ <s2> [ <s3> [ <s4> [ <s5> [ <s6> [ <s7> ] ] ] ] ] ] ] [ local1| none ] | local [ none1 ] | none2 }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure accounting methodsaccounting
Configure default methodsdefault
Specify server groups to redirect the accounting logsgroup
Server group names0
(Optional) Server group names1
(Optional) Server group names2
(Optional) Server group names3
(Optional) Server group names4
(Optional) Server group names5
(Optional) Server group names6
(Optional) Server group names7
(Optional) No accountingnone
(Optional) No accountingnone1
No accountingnone2
Use local accountinglocal
(Optional) Use local accountinglocal1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)8
A Commandsaaa accounting default
Page 153
aaa accounting dot1x default group[no] aaa accounting dot1x default group <grp_name> +
Syntax Description
Configure aaa functionsaaa
Configure accounting methodsaccounting
accounting methods for dot1xdot1x
default aaa methodsdefault
server group namegrp_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)9
A Commandsaaa accounting dot1x default group
Page 154
aaa authentication dot1x default group[no] aaa authentication dot1x default group <grp_name> +
Syntax Description
Configure aaa functionsaaa
Configure authentication methodsauthentication
server group namegrp_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)10
A Commandsaaa authentication dot1x default group
Page 155
aaa authentication login ascii-authentication[no] aaa authentication login ascii-authentication
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure authentication methodsauthentication
Configure methods for loginlogin
enable ascii authenticationascii-authentication
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)11
A Commandsaaa authentication login ascii-authentication
Page 156
aaa authentication login console[no] aaa authentication login console { group <s0> [ { local1 | none | <s1> [ { local1 | none | <s2> [ { local1| none | <s3> [ { local1 | none | <s4> [ { local1 | none | <s5> [ { local1 | none | <s6> [ { local1 | none | <s7> [{ local1 | none } ] } ] } ] } ] } ] } ] } ] } ] | local | none }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure authentication methodsauthentication
Configure methods for loginlogin
Configure console methodsconsole
Specify server groupsgroup
Server group names0
(Optional) No authenticationnone
(Optional) Server group names1
(Optional) No authenticationnone
(Optional) Server group names2
(Optional) No authenticationnone
(Optional) Server group names3
(Optional) No authenticationnone
(Optional) Server group names4
(Optional) No authenticationnone
(Optional) Server group names5
(Optional) No authenticationnone
(Optional) Server group names6
(Optional) No authenticationnone
(Optional) Server group names7
(Optional) No authenticationnone
Use local username authenticationlocal
(Optional) Use local username authenticationlocal1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)12
A Commandsaaa authentication login console
Page 157
No authenticationnone
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)13
A Commandsaaa authentication login console
Page 158
aaa authentication login default[no] aaa authentication login default { group <s0> [ { local1 | none | <s1> [ { local1 | none | <s2> [ { local1 |none | <s3> [ { local1 | none | <s4> [ { local1 | none | <s5> [ { local1 | none | <s6> [ { local1 | none | <s7> [ {local1 | none } ] } ] } ] } ] } ] } ] } ] } ] | local | none }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure authentication methodsauthentication
Configure methods for loginlogin
Configure default methodsdefault
Specify server groupsgroup
Server group names0
(Optional) No authenticationnone
(Optional) Server group names1
(Optional) No authenticationnone
(Optional) Server group names2
(Optional) No authenticationnone
(Optional) Server group names3
(Optional) No authenticationnone
(Optional) Server group names4
(Optional) No authenticationnone
(Optional) Server group names5
(Optional) No authenticationnone
(Optional) Server group names6
(Optional) No authenticationnone
(Optional) Server group names7
(Optional) No authenticationnone
Use local username authenticationlocal
(Optional) Use local username authenticationlocal1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)14
A Commandsaaa authentication login default
Page 159
No authenticationnone
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)15
A Commandsaaa authentication login default
Page 160
aaa authentication login default fallback error local[no] aaa authentication login { default | console } fallback error local
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure authentication methodsauthentication
Configure methods for loginlogin
Configure default methodsdefault
Configure console methodsconsole
Configure fallback behaviorfallback
Fallback in case all AAA servers configured for remote authenticationare unreachable (Authentication error)
error
Fallback to local authenticationlocal
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)16
A Commandsaaa authentication login default fallback error local
Page 161
aaa authentication login enable[no] aaa authentication login { mschap | mschapv2 | chap } enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure authentication methodsauthentication
Configure methods for loginlogin
MSCHAP authentication for loginmschap
MSCHAP V2 authentication for loginmschapv2
CHAP authentication for loginchap
enable the authentication for loginenable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)17
A Commandsaaa authentication login enable
Page 162
aaa authentication login error-enable[no] aaa authentication login error-enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure authentication methodsauthentication
Configure methods for loginlogin
enable display of error message on login failureserror-enable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)18
A Commandsaaa authentication login error-enable
Page 163
aaa authentication login invalid-username-log[no] aaa authentication login invalid-username-log
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure authentication methodsauthentication
Configure methods for loginlogin
enable invalid username loginvalid-username-log
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)19
A Commandsaaa authentication login invalid-username-log
Page 164
aaa authentication login password-aging enable[no] aaa authentication login password-aging enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure authentication methodsauthentication
Configure methods for loginlogin
password-aging authentication for loginpassword-aging
enable password-aging notificationenable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)20
A Commandsaaa authentication login password-aging enable
Page 165
aaa authentication rejected[no] aaa authentication rejected
Syntax Description
Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure authentication methodsauthentication
Set max number of fail attemptsrejected
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)21
A Commandsaaa authentication rejected
Page 166
aaa authentication rejected in banaaa authentication rejected <i1> in <i2> ban <i3>
Syntax Description
Configure aaa functionsaaa
Configure authentication methodsauthentication
Set max number of fail attemptsrejected
Fail attempts max valuei1
Watch period for fail attemptsin
Time period in secondsi2
Block time periodban
Time period in secondsi3
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)22
A Commandsaaa authentication rejected in ban
Page 167
aaa authorization commands console[no] aaa authorization { commands | config-commands } console { group <s0> [ { local | none | <s1> [ { local| none | <s2> [ { local | none | <s3> [ { local | none | <s4> [ { local | none | <s5> [ { local | none | <s6> [ { local| none | <s7> [ { local | none } ] } ] } ] } ] } ] } ] } ] } ] | local | none }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure authorization methodsauthorization
Authorization for all exec-mode commandscommands
Authorization for config commandsconfig-commands
Configure methods consoleconsole
Specify server groupsgroup
Server group names0
(Optional) Server group names1
(Optional) Server group names2
(Optional) Server group names3
(Optional) Server group names4
(Optional) Server group names5
(Optional) Server group names6
(Optional) Server group names7
(Optional) Use local RBACL based authorizationlocal
(Optional) No authorizationnone
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)23
A Commandsaaa authorization commands console
Page 168
aaa authorization commands default[no] aaa authorization { commands | config-commands } default { group <s0> [ { local | none | <s1> [ { local| none | <s2> [ { local | none | <s3> [ { local | none | <s4> [ { local | none | <s5> [ { local | none | <s6> [ { local| none | <s7> [ { local | none } ] } ] } ] } ] } ] } ] } ] } ] | local | none }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure authorization methodsauthorization
Authorization for all exec-mode commandscommands
Authorization for config commandsconfig-commands
Configure default methodsdefault
Specify server groupsgroup
Server group names0
(Optional) Server group names1
(Optional) Server group names2
(Optional) Server group names3
(Optional) Server group names4
(Optional) Server group names5
(Optional) Server group names6
(Optional) Server group names7
(Optional) Use local RBACL based authorizationlocal
(Optional) No authorizationnone
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)24
A Commandsaaa authorization commands default
Page 169
aaa authorization ssh default group[no] aaa authorization { ssh-publickey | ssh-certificate } default { group <s0> [ { local1 | <s1> [ { local1 |<s2> [ { local1 | <s3> [ { local1 | <s4> [ { local1 | <s5> [ { local1 | <s6> [ { local1 | <s7> [ { local1 } ] } ] }] } ] } ] } ] } ] } ] | local }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure authorization methodsauthorization
Configure ssh publickeyssh-publickey
Configure ssh certificatessh-certificate
Configure default ssh methodsdefault
Specify server groupsgroup
Server group names0
(Optional) Server group names1
(Optional) Server group names2
(Optional) Server group names3
(Optional) Server group names4
(Optional) Server group names5
(Optional) Server group names6
(Optional) Server group names7
Use local username authenticationlocal
(Optional) Use local username authenticationlocal1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)25
A Commandsaaa authorization ssh default group
Page 170
aaa bypass-user[no] aaa bypass-user <s0> { [ accounting ] [ authorization ] | [ authorization ] [ accounting ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure bypass userbypass-user
Enter the usernames0
(Optional) Bypass accountingaccounting
(Optional) Bypass authorizationauthorization
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)26
A Commandsaaa bypass-user
Page 171
aaa group server ldap[no] aaa group server ldap <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure aaa server groupgroup
Configure aaa server groupserver
LDAP server group nameldap
LDAP server group names0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)27
A Commandsaaa group server ldap
Page 172
aaa group server radius[no] aaa group server radius <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure aaa server groupgroup
Configure aaa server groupserver
RADIUS server group nameradius
RADIUS server group names0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)28
A Commandsaaa group server radius
Page 173
aaa group server tacacs[no] aaa group server tacacs <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Configure aaa server groupgroup
Configure aaa server groupserver
TACACS+ server group nametacacs
TACACS+ server group names0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)29
A Commandsaaa group server tacacs
Page 174
aaa test-authentication[no] aaa test-authentication
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Test aaa authenticationtest-authentication
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)30
A Commandsaaa test-authentication
Page 175
aaa test-radius-authentication[no] aaa test-radius-authentication
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Test aaa radius authenticationtest-radius-authentication
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)31
A Commandsaaa test-radius-authentication
Page 176
aaa user default-role[no] aaa user default-role
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure aaa functionsaaa
Remotely authenticated useruser
Default role assigned by aaa-admin for remote authenticationdefault-role
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)32
A Commandsaaa user default-role
Page 177
abortabort
Syntax Description
Exit region configuration mode, aborting changesabort
Command Mode
• /exec/configure/spanning-tree/mst/configuration
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)33
A Commandsabort
Page 178
abortabort
Syntax Description
Abort the current configuration sessionabort
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)34
A Commandsabort
Page 179
abortabort
Syntax Description
abort itd sessionabort
Command Mode
• /exec/configure/itd-session-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)35
A Commandsabort
Page 180
abortabort
Syntax Description
abort plb sessionabort
Command Mode
• /exec/configure/plb-session-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)36
A Commandsabort
Page 181
absolute-timeout{ absolute-timeout <i0> | no absolute-timeout [ <i0> ] }
Syntax Description
Negate a command or set its defaultsno
Configure absolute timeoutabsolute-timeout
Enter timeout in minutes, 0 to disablei0
Command Mode
• /exec/configure/line
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)37
A Commandsabsolute-timeout
Page 182
absolute start{ [ <seqno> ] | no } absolute { start <stime> <sday> <smonth> <syear> [ end <etime> <eday> <emonth><eyear> ] | end <etime> <eday> <emonth> <eyear> }
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Absolute time and dateabsolute
Starting time and datestart
Starting timestime
Day of the monthsday
Monthsmonth
Yearsyear
(Optional) Ending time and dateend
(Optional) Ending timeetime
(Optional) Day of the montheday
(Optional) Monthemonth
(Optional) Yeareyear
Command Mode
• /exec/configure/timerange
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)38
A Commandsabsolute start
Page 183
accept-lifetime month_a month_b month_c month_d month_emonth_f month_g month_h month_i month_j month_k month_lduration infinite month_a month_b month_c month_d month_emonth_f month_g month_h month_i month_j month_k month_l
{ { accept-lifetime [ local ] <stime> { month_a | month_b | month_c | month_d | month_e | month_f | month_g| month_h | month_i | month_j | month_k | month_l } <sday> <syear> { duration <dsec> | infinite | <etime>{ month_a | month_b | month_c | month_d | month_e | month_f | month_g | month_h | month_i | month_j |month_k | month_l } <eday> <eyear> } } | { no accept-lifetime [ [ local ] <stime> { month_a | month_b |month_c | month_d | month_e | month_f | month_g | month_h | month_i | month_j | month_k | month_l }<sday> <syear> { duration <dsec> | infinite | <etime> { month_a | month_b | month_c | month_d | month_e| month_f | month_g | month_h | month_i | month_j | month_k | month_l } <eday> <eyear> } ] } }
Syntax Description
Negate a command or set its defaultsno
Set accept lifetime of keyaccept-lifetime
(Optional) Specify time in local timezonelocal
HH:MM:SS Time to start <0-23>:<0-59>:<0-59>stime
HH:MM:SS Time to end <0-23>:<0-59>:<0-59>etime
month_a
month_b
month_c
month_d
month_e
month_f
month_g
month_h
month_i
month_j
month_k
month_l
Day of the month to startsday
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)39
A Commandsaccept-lifetime month_a month_b month_c month_d month_e month_f month_g month_h month_i month_j month_k month_l duration infinite month_a month_b
month_c month_d month_e month_f month_g month_h month_i month_j month_k month_l
Page 184
Day of the month to endeday
Year to startsyear
Year to starteyear
Set key lifetime durationduration
Duration in secondsdsec
Never Expiresinfinite
Command Mode
• /exec/configure/keychain-key
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)40
A Commandsaccept-lifetime month_a month_b month_c month_d month_e month_f month_g month_h month_i month_j month_k month_l duration infinite month_a month_bmonth_c month_d month_e month_f month_g month_h month_i month_j month_k month_l
Page 185
access-class[no] access-class <name> <inout>
Syntax Description
(Optional) Negate a command or set its defaultsno
Specify IPv4 access control for packetsaccess-class
List namename
Traffic directioninout
Command Mode
• /exec/configure/line
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)41
A Commandsaccess-class
Page 186
access-list[no] access-list <acl-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure access-list for PLB serviceaccess-list
Access-list nameacl-name
Command Mode
• /exec/configure/plb
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)42
A Commandsaccess-list
Page 187
access-list[no] access-list <acl-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD access-list nameaccess-list
ITD user ACL nameacl-name
Command Mode
• /exec/configure/itd
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)43
A Commandsaccess-list
Page 188
access-list ipv6[no] access-list ipv6 <acl-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD access-list nameaccess-list
ipv6 access-listipv6
ITD user ACL nameacl-name
Command Mode
• /exec/configure/itd
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)44
A Commandsaccess-list ipv6
Page 189
access vlan[no] access vlan <vlan>
Syntax Description
(Optional) Negate a command or set its defaultsno
accessaccess
vlanvlan
Vlanvlan
Command Mode
• /exec/configure/smartc /exec/configure/smartc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)45
A Commandsaccess vlan
Page 190
acllog match-log-level[no] acllog match-log-level <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure ACL loggingacllog
acllog logging levelmatch-log-level
match log levellevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)46
A Commandsacllog match-log-level
Page 191
action[no] action { drop [ log ] | forward | redirect <intf> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Specify the action clauseaction
Drop matched packetsdrop
(Optional) Log matched packetslog
Forward matched packetsforward
Redirect matched packets to the specified interface(s)redirect
Interface traffic is redirected tointf
Command Mode
• /exec/configure/vacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)47
A Commandsaction
Page 192
action[no] action <label>
Syntax Description
Negate a command or set its defaultsno
Configure the actions to be executedaction
Enter the label <num1>[.<num2>] for action order num2 must be 0-9label
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)48
A Commandsaction
Page 193
action cliaction <label> cli [ local ] <vsh_cmd>
Syntax Description
Configure the actions to be executedaction
Enter the label <num1>[.<num2>] for action order num2 must be 0-9label
Configure a VSH CLI actioncli
(Optional) Execute the action in the same card on which the eventhappens
local
Enter the vsh commandvsh_cmd
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)49
A Commandsaction cli
Page 194
action counter name value opaction <label> counter name <counter-name> value <counter-value> op <op-val>
Syntax Description
Configure the actions to be executedaction
Enter the label <num1>[.<num2>] for action order num2 must be 0-9label
Specify the name of the countercounter
Specify the name of the countername
Name of the countercounter-name
Specify the value to be applied to the countervalue
Enter an integer value or a $ prefixed name (parameter substitution)counter-value
Specify the operator to be appliedop
Enter the value of the operatorop-val
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)50
A Commandsaction counter name value op
Page 195
action eem testaction <label> eem test <param>
Syntax Description
Configure the actions to be executedaction
Enter the label <num1>[.<num2>] for action order num2 must be 0-9label
Event Manager commandeem
Do test actiontest
Test action parameter (dummy value)param
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)51
A Commandsaction eem test
Page 196
action event-defaultaction <label> event-default
Syntax Description
Configure the actions to be executedaction
Enter the label <num1>[.<num2>] for action order num2 must be 0-9label
Do default action for the eventevent-default
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)52
A Commandsaction event-default
Page 197
action forceshut reset-reason[no] action <label2> forceshut [ { module { <module> | <mod-str> } | <s0> { <santa-cruz-range> |<santa-cruz-string> } } ] reset-reason <reset_reason_string>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure the actions to be executedaction
Enter the label <num1>[.<num2>] for action order num2 must be 0-9label2
Force the entire switch to shut downforceshut
(Optional) Optional. Module to be forced to shut down(optionalargument)
module
(Optional) please enter the module numbermodule
(Optional) Enter the module number (integer value) or a $ prefixedparameter name
mod-str
(Optional) Optional. Xbar to be forced to shut down(optional argument)s0
(Optional) please enter the xbar numbersanta-cruz-range
(Optional) Enter the xbar number (integer value) or a $ prefixedparameter name
santa-cruz-string
Shut down (with reset-reason)reset-reason
please enter reset_reason_string in quotesreset_reason_string
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)53
A Commandsaction forceshut reset-reason
Page 198
action overbudgetshut[no] action <label> overbudgetshut [ module { <module> | <mod-str> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure the actions to be executedaction
Enter the label <num1>[.<num2>] for action order num2 must be 0-9label
Shut down the specified LCs due to power over budgetoverbudgetshut
(Optional) Optional. Module to be force-shut(optional arg)module
(Optional) please enter the module numbermodule
(Optional) Enter the module number (integer value) or a $ prefixedparameter name
mod-str
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)54
A Commandsaction overbudgetshut
Page 199
action policy-defaultaction <label> policy-default
Syntax Description
Configure the actions to be executedaction
Enter the label <num1>[.<num2>] for action order num2 must be 0-9label
Do default action(s) of the policy being overriddenpolicy-default
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)55
A Commandsaction policy-default
Page 200
action reload[no] action <label> reload [ module { <module> | <mod-str> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure the actions to be executedaction
Enter the label <num1>[.<num2>] for action order num2 must be 0-9label
Reload the system or a specific modulereload
(Optional) Reload a specific modulemodule
(Optional) please enter the module numbermodule
(Optional) Enter the module number (integer value) or a $ prefixedparameter name
mod-str
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)56
A Commandsaction reload
Page 201
action snmp-trapaction <label> snmp-trap [ intdata1 <integer-data1> ] [ intdata2 <integer-data2> ] [ strdata <string-data> ]
Syntax Description
Configure the actions to be executedaction
Enter the label <num1>[.<num2>] for action order num2 must be 0-9label
Sendsnmp-trap
(Optional) Enterintdata1
(Optional) Integerinteger-data1
(Optional) Enterintdata2
(Optional) Integerinteger-data2
(Optional) Enterstrdata
(Optional) Stringstring-data
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)57
A Commandsaction snmp-trap
Page 202
action syslog msgaction <label> syslog [ priority { <prio> | <prio-str> } ] msg <msg-text>
Syntax Description
Configure the actions to be executedaction
Enter the label <num1>[.<num2>] for action order num2 must be 0-9label
Generate a syslog messagesyslog
(Optional) Priority of the syslog messagepriority
(Optional) Enter the priorityprio
(Optional) Enter a valid $ prefixed name, for parameter substitutionprio-str
Enter the message for the syslogmsg
The message textmsg-text
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)58
A Commandsaction syslog msg
Page 203
additional-paths install backup[no] additional-paths install backup
Syntax Description
(Optional) Negate a command or set its defaultsno
Additional paths configurationadditional-paths
Install backup pathinstall
Install backup pathbackup
Command Mode
• /exec/configure/router-bgp/router-bgp-af-ipv6 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6/exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)59
A Commandsadditional-paths install backup
Page 204
additional-paths receive[no] additional-paths receive
Syntax Description
(Optional) Negate a command or set its defaultsno
Additional paths configurationadditional-paths
Additional paths Receive capabilityreceive
Command Mode
• /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-af-ipv6-mvpn /exec/configure/router-bgp/router-bgp-af-vpnv4/exec/configure/router-bgp/router-bgp-af-vpnv6 /exec/configure/router-bgp/router-bgp-af-ipv4-label/exec/configure/router-bgp/router-bgp-af-ipv6-label /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)60
A Commandsadditional-paths receive
Page 205
additional-paths selection route-map[no] additional-paths selection route-map <rmap-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Additional paths configurationadditional-paths
Additional paths selectionselection
Route-map for additional paths selectionroute-map
Route-map namermap-name
Command Mode
• /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-vpnv4/exec/configure/router-bgp/router-bgp-af-vpnv6 /exec/configure/router-bgp/router-bgp-af-ipv6-label/exec/configure/router-bgp/router-bgp-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-af-ipv6-mvpn/exec/configure/router-bgp/router-bgp-af-ipv4-label /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)61
A Commandsadditional-paths selection route-map
Page 206
additional-paths send[no] additional-paths send
Syntax Description
(Optional) Negate a command or set its defaultsno
Additional paths configurationadditional-paths
Additional paths Send capabilitysend
Command Mode
• /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-vpnv4/exec/configure/router-bgp/router-bgp-af-vpnv6 /exec/configure/router-bgp/router-bgp-af-ipv6-label/exec/configure/router-bgp/router-bgp-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-af-ipv6-mvpn/exec/configure/router-bgp/router-bgp-af-ipv4-label /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)62
A Commandsadditional-paths send
Page 207
address-family ipv4[no] address-family ipv4
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an address-familyaddress-family
Configure IPv4 address-familyipv4
Command Mode
• /exec/configure/config-sr-mpls/config-sr-mpls-conn-pfxsid
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)63
A Commandsaddress-family ipv4
Page 208
address-family ipv4 labeled-unicast{ [ no | default ] } address-family ipv4 labeled-unicast
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure an address-family for peeraddress-family
Configure IPv4 address-familyipv4
Configure labeled unicast sub-address-familylabeled-unicast
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor/exec/configure/router-bgp/router-bgp-prefixneighbor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)64
A Commandsaddress-family ipv4 labeled-unicast
Page 209
address-family ipv4 labeled-unicast[no] address-family ipv4 labeled-unicast
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an address-familyaddress-family
Configure IPv4 address-familyipv4
Configure labeled unicast sub-address-familylabeled-unicast
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)65
A Commandsaddress-family ipv4 labeled-unicast
Page 210
address-family ipv4 mdt{ [ no | default ] } address-family ipv4 mdt
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure an address-familyaddress-family
Configure IPv4 address-familyipv4
Configure Multicast Distribution Treemdt
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor/exec/configure/router-bgp/router-bgp-prefixneighbor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)66
A Commandsaddress-family ipv4 mdt
Page 211
address-family ipv4 mdt[no] address-family ipv4 mdt
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an address-familyaddress-family
Configure IPv4 address-familyipv4
Configure Multicast Distribution Treemdt
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)67
A Commandsaddress-family ipv4 mdt
Page 212
address-family ipv4 mvpn[no] address-family ipv4 mvpn
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an address-familyaddress-family
Configure IPv4 address-familyipv4
Configure Multicast VPNmvpn
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)68
A Commandsaddress-family ipv4 mvpn
Page 213
address-family ipv4 mvpn{ [ no | default ] } address-family ipv4 mvpn
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure an address-familyaddress-family
Configure IPv4 address-familyipv4
Configure Multicast VPNmvpn
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor/exec/configure/router-bgp/router-bgp-prefixneighbor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)69
A Commandsaddress-family ipv4 mvpn
Page 214
address-family ipv6[no] address-family ipv6
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an address-familyaddress-family
Configure IPv6 address-familyipv6
Command Mode
• /exec/configure/config-sr-mpls/config-sr-mpls-conn-pfxsid
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)70
A Commandsaddress-family ipv6
Page 215
address-family ipv6 labeled-unicast{ [ no | default ] } address-family ipv6 labeled-unicast
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure an address-family for peeraddress-family
Configure IPv6 address-familyipv6
Configure labeled unicast sub-address-familylabeled-unicast
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor/exec/configure/router-bgp/router-bgp-prefixneighbor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)71
A Commandsaddress-family ipv6 labeled-unicast
Page 216
address-family ipv6 labeled-unicast[no] address-family ipv6 labeled-unicast
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an address-familyaddress-family
Configure IPv6 address-familyipv6
Configure labeled unicast sub-address-familylabeled-unicast
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)72
A Commandsaddress-family ipv6 labeled-unicast
Page 217
address-family ipv6 mvpn{ [ no | default ] } address-family ipv6 mvpn
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure an address-familyaddress-family
Configure IPv6 address-familyipv6
Configure Multicast VPNmvpn
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor/exec/configure/router-bgp/router-bgp-prefixneighbor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)73
A Commandsaddress-family ipv6 mvpn
Page 218
address-family ipv6 mvpn[no] address-family ipv6 mvpn
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an address-familyaddress-family
Configure IPv6 address-familyipv6
Configure Multicast VPNmvpn
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)74
A Commandsaddress-family ipv6 mvpn
Page 219
address-family l2vpn evpn[no] address-family l2vpn evpn
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an address-familyaddress-family
Configure L2VPN address-familyl2vpn
Configure L2VPN EVPN address-familyevpn
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)75
A Commandsaddress-family l2vpn evpn
Page 220
address-family l2vpn evpn{ [ no | default ] } address-family l2vpn evpn
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure an address-familyaddress-family
Configure L2VPN address-familyl2vpn
Configure L2VPN EVPN address-familyevpn
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor/exec/configure/router-bgp/router-bgp-prefixneighbor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)76
A Commandsaddress-family l2vpn evpn
Page 221
address-family l2vpn vpls{ [ no | default ] } address-family l2vpn vpls
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure an address-familyaddress-family
Configure L2VPN address-familyl2vpn
Configure L2VPN VPLS address-familyvpls
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor/exec/configure/router-bgp/router-bgp-prefixneighbor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)77
A Commandsaddress-family l2vpn vpls
Page 222
address-family l2vpn vpls[no] address-family l2vpn vpls
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an address-familyaddress-family
Configure L2VPN address-familyl2vpn
Configure L2VPN VPLS address-familyvpls
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)78
A Commandsaddress-family l2vpn vpls
Page 223
address-family link-state[no] address-family link-state
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an address-familyaddress-family
Configure link-state address-familylink-state
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)79
A Commandsaddress-family link-state
Page 224
address-family link-state{ [ no | default ] } address-family link-state
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure an address-familyaddress-family
Configure link-state address-familylink-state
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor/exec/configure/router-bgp/router-bgp-prefixneighbor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)80
A Commandsaddress-family link-state
Page 225
address-family vpnv4 unicast[no] address-family vpnv4 unicast
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an address-familyaddress-family
Configure IPv4 VPN address-familyvpnv4
Configure Unicast sub-address-familyunicast
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)81
A Commandsaddress-family vpnv4 unicast
Page 226
address-family vpnv4 unicast{ [ no | default ] } address-family vpnv4 unicast
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure an address-family for peeraddress-family
Configure IPv4 VPN address-familyvpnv4
Configure Unicast sub-address-familyunicast
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor/exec/configure/router-bgp/router-bgp-prefixneighbor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)82
A Commandsaddress-family vpnv4 unicast
Page 227
address-family vpnv6 unicast[no] address-family vpnv6 unicast
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an address-familyaddress-family
Configure IPv6 VPN address-familyvpnv6
Configure Unicast sub-address-familyunicast
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)83
A Commandsaddress-family vpnv6 unicast
Page 228
address-family vpnv6 unicast{ [ no | default ] } address-family vpnv6 unicast
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure an address-family for peeraddress-family
Configure IPv6 VPN address-familyvpnv6
Configure Unicast sub-address-familyunicast
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-template-neighbor/exec/configure/router-bgp/router-bgp-prefixneighbor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)84
A Commandsaddress-family vpnv6 unicast
Page 229
address[no] address <ipv6_addr>
Syntax Description
(Optional) Negate a command or set its defaultsno
IP Address configurationaddress
Command Mode
• /exec/configure/if-eth-any/vrrs
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)85
A Commandsaddress
Page 230
address{ address <ip_address> | no address [ <ip_address> ] }
Syntax Description
Negate a command or set its defaultsno
Add an IP address to the vraddress
ip addressip_address
Command Mode
• /exec/configure/if-eth-any/vrrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)86
A Commandsaddress
Page 231
address[no] address <ip_addr> [ primary ]
Syntax Description
(Optional) Negate a command or set its defaultsno
IP Addressaddress
(Optional) Primary Addressprimary
IPv4 Addressip_addr
Command Mode
• /exec/configure/if-eth-any/vrrpv3_ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)87
A Commandsaddress
Page 232
address[no] address <ipv6_addr>
Syntax Description
(Optional) Negate a command or set its defaultsno
IP Addressaddress
Command Mode
• /exec/configure/if-eth-any/vrrpv3_ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)88
A Commandsaddress
Page 233
address[no] address <ip_addr>
Syntax Description
(Optional) Negate a command or set its defaultsno
IP Address configurationaddress
IP Addressip_addr
Command Mode
• /exec/configure/if-eth-any/vrrs
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)89
A Commandsaddress
Page 234
address[no] address <start-ip> <end-ip>
Syntax Description
(Optional) Negate a command or set its defaultsno
Address range for the pooladdress
Start IP addressstart-ip
End IP addressend-ip
Command Mode
• /exec/configure/ipnat-pool
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)90
A Commandsaddress
Page 235
address port-numberaddress { <ipv4-addr> | <ipv6-addr> } port-number <port-number> | no address
Syntax Description
Negate a command or set its defaultsno
Configure IPv4 or IPv6 addressaddress
IPv4 address of the BMP serveripv4-addr
Configure the port for the BMP serverport-number
Port number valueport-number
Command Mode
• /exec/configure/router-bgp/router-bgp-bmp-server
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)91
A Commandsaddress port-number
Page 236
address primary[no] address <ipv6_addr> primary
Syntax Description
(Optional) Negate a command or set its defaultsno
IP Addressaddress
Primary Addressprimary
Command Mode
• /exec/configure/if-eth-any/vrrpv3_ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)92
A Commandsaddress primary
Page 237
address secondary[no] address <ip_addr> secondary
Syntax Description
(Optional) Negate a command or set its defaultsno
IP Addressaddress
Secondary Addresssecondary
IPv4 Addressip_addr
Command Mode
• /exec/configure/if-eth-any/vrrpv3_ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)93
A Commandsaddress secondary
Page 238
address secondary{ address <ip_address> secondary | no address <ip_address> secondary }
Syntax Description
Negate a command or set its defaultsno
Add an IP address to the vraddress
ip addressip_address
a virtual IP address without ownersecondary
Command Mode
• /exec/configure/if-eth-any/vrrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)94
A Commandsaddress secondary
Page 239
adjacency-check[no] adjacency-check
Syntax Description
(Optional) Negate a command or set its defaultsno
Adjacency's protocol support consistency checkadjacency-check
Command Mode
• /exec/configure/router-isis/router-isis-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)95
A Commandsadjacency-check
Page 240
adjacency-resolve[no] adjacency-resolve
Syntax Description
(Optional) Negate a command or set its defaultsno
Resolve L3->L2 address for ISIS adjacencyadjacency-resolve
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)96
A Commandsadjacency-resolve
Page 241
advertise-gw-ip[ no | default ] advertise-gw-ip
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Advertise Gateway IP in Type-5 routes to neighboradvertise-gw-ip
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)97
A Commandsadvertise-gw-ip
Page 242
advertise-labels[no] advertise-labels [ vrf { <vrf-name> | <vrf-known-name> } ] [ [ for <pfx-list> [ to <peer-pfx-list> ] ] | [interface <intf> ] ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Label advertisementsadvertise-labels
(Optional) VRF Routing/Forwarding instance informationvrf
(Optional) VPN Routing/Forwarding instance namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Prefix list specifying controls on destination prefixesfor
(Optional) Name of prefix listpfx-list
(Optional) Prefix list specifying controls on LDP peersto
(Optional) Name of prefix listpeer-pfx-list
(Optional) Advertise /32 interface addressinterface
(Optional)intf
Command Mode
• /exec/configure/ldp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)98
A Commandsadvertise-labels
Page 243
advertise-map exist default advertise-map{ [ no ] advertise-map <advt-rmap-name> { exist-map | non-exist-map } <cond-rmap-name> } | defaultadvertise-map
Syntax Description
(Optional) Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Specify route-map for conditional advertisementadvertise-map
Condition route-map to advertise only when prefix in condition existsexist-map
Condition route-map to advertise only when prefix in condition doesnot exist
non-exist-map
Route-map nameadvt-rmap-name
Route-map namecond-rmap-name
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)99
A Commandsadvertise-map exist default advertise-map
Page 244
advertise-pip[no] advertise-pip
Syntax Description
(Optional) Negate a command or set its defaultsno
advertise physical ip for type-5 routeadvertise-pip
Command Mode
• /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)100
A Commandsadvertise-pip
Page 245
advertise-system-mac[no] advertise-system-mac
Syntax Description
(Optional) Negate a command or set its defaultsno
Advertise extra EVPN RT-2 with system MACadvertise-system-mac
Command Mode
• /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)101
A Commandsadvertise-system-mac
Page 246
advertise evpn multicast[no] advertise evpn multicast
Syntax Description
(Optional) Negate a command or set its defaultsno
Advertise L2 multicast capabilityadvertise
evpnevpn
L2 multicastmulticast
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)102
A Commandsadvertise evpn multicast
Page 247
advertise interface[no] advertise interface <interface> [ <level> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Advertise interface IPadvertise
Advertise interface IPinterface
Interface to advertiseinterface
(Optional) IS-IS levellevel
Command Mode
• /exec/configure/router-isis/router-isis-af-ipv4 /exec/configure/router-isis/router-isis-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)103
A Commandsadvertise interface
Page 248
advertise l2vpn evpn[no] advertise l2vpn evpn
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure advertise for this AFadvertise
L2VPNl2vpn
EVPNevpn
Command Mode
• /exec/configure/router-bgp/router-bgp-vrf-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)104
A Commandsadvertise l2vpn evpn
Page 249
advertise local-labeled-route[ no | default ] advertise local-labeled-route
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Advertise to peeradvertise
Advertise a route with local label to peerlocal-labeled-route
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)105
A Commandsadvertise local-labeled-route
Page 250
advertise virtual-rmac[no] advertise virtual-rmac
Syntax Description
(Optional) Negate a command or set its defaultsno
Reachability advertisementadvertise
Advertise virtual RMAC capabilityvirtual-rmac
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)106
A Commandsadvertise virtual-rmac
Page 251
advertisement-interval[no] advertisement-interval <adv-sec>
Syntax Description
(Optional) Negate a command or set its defaultsno
Minimum interval between sending BGP routing updatesadvertisement-interval
Time in secondsadv-sec
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)107
A Commandsadvertisement-interval
Page 252
advertisement-interval{ advertisement-interval <interval_time> | no advertisement-interval [ <interval_time> ] }
Syntax Description
Negate a command or set its defaultsno
Set the time interval between advertisementadvertisement-interval
Time interval (in seconds) between advertisementsinterval_time
Command Mode
• /exec/configure/if-eth-any/vrrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)108
A Commandsadvertisement-interval
Page 253
afd queue-desired[no] afd queue-desired <q-desired> { bytes | kbytes | mbytes } [ ecn ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure AFD parametersafd
Specify Queue Desired for AFDqueue-desired
Bytesbytes
Kilo byteskbytes
Mega bytesmbytes
(Optional) ECNecn
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)109
A Commandsafd queue-desired
Page 254
affinity-group{ affinity-group <affinity_group_id> } | { { no | default } affinity-group [ <affinity_group_id> ] }
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Configure an affinity groupaffinity-group
Affinity Group IDaffinity_group_id
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)110
A Commandsaffinity-group
Page 255
affinity-group activateaffinity-group activate <affinity_group_id> | no affinity-group activate [ <affinity_group_id> ]
Syntax Description
Negate a command or set its defaultsno
Configure an affinity groupaffinity-group
Activate the affinity groupactivate
AFFINITY Group IDaffinity_group_id
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)111
A Commandsaffinity-group activate
Page 256
affinity[no] affinity | affinity <hex_value> [ mask <mask_value> ]
Syntax Description
Negate a command or set its defaultsno
Specify attribute flags for links comprising LSPaffinity
affinity valuehex_value
(Optional) mask on desired link attributesmask
(Optional) affinity mask valuemask_value
Command Mode
• /exec/configure/te/lsp-attr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)112
A Commandsaffinity
Page 257
affinity[no] affinity | affinity <value> [ mask <mask-value> ]
Syntax Description
Negate a command or set its defaultsno
desired link attributes for links comprising tunnelaffinity
affinity valuevalue
(Optional) mask on desired link attributesmask
(Optional) affinity mask valuemask-value
Command Mode
• /exec/configure/if-te /exec/configure/tunnel-te/cbts-member
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)113
A Commandsaffinity
Page 258
age{ [ no ] age <age> | no age }
Syntax Description
Provide the age value for this POSTCARD flow-profileage
flow-profile age (seconds). Default is 30.age
Command Mode
• /exec/configure/config-postcard-flow-prof
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)114
A Commandsage
Page 259
age{ [ no ] age <age> | no age }
Syntax Description
Provide the age value for this INT flow-profileage
flow-profile age (seconds). Default is 30.age
Command Mode
• /exec/configure/config-int-flow-prof
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)115
A Commandsage
Page 260
aggregate-address[no] aggregate-address { <ip-addr> <ip-mask> | <ip-prefix> } [ as-set | summary-only | suppress-map<suppress-rmap> | advertise-map <advertise-rmap> | attribute-map <attribute-rmap> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure BGP aggregate prefixesaggregate-address
Aggregate addressip-addr
Aggregate maskip-mask
Aggregate prefixip-prefix
(Optional) Don't advertise more specificssummary-only
(Optional) Generate AS-SET informationas-set
(Optional) Conditionally filter more specific routessuppress-map
(Optional) Select attribute information from specific routesadvertise-map
(Optional) Set attribute information of aggregateattribute-map
(Optional) Route-map nameadvertise-rmap
(Optional) Route-map namesuppress-rmap
(Optional) Route-map nameattribute-rmap
Command Mode
• /exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)116
A Commandsaggregate-address
Page 261
aggregate-address[no] aggregate-address <ipv6-prefix> [ as-set | summary-only | suppress-map <suppress-rmap> | advertise-map<advertise-rmap> | attribute-map <attribute-rmap> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure BGP aggregate IPv6 prefixesaggregate-address
(Optional) Generate AS-SET informationas-set
(Optional) Don't advertise more specificssummary-only
(Optional) Conditionally filter more specific routessuppress-map
(Optional) Select attribute information from specific routesadvertise-map
(Optional) Set attribute information of aggregateattribute-map
(Optional) Route-map nameadvertise-rmap
(Optional) Route-map namesuppress-rmap
(Optional) Route-map nameattribute-rmap
Command Mode
• /exec/configure/router-bgp/router-bgp-af-ipv6 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)117
A Commandsaggregate-address
Page 262
alert-group user-def-cmd[no] alert-group { Configuration | Diagnostic | Environmental | Inventory | License | Linecard-Hardware |Supervisor-Hardware | Syslog-group-port | System | Test } user-def-cmd <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
alert groupalert-group
configure a cli command for an alert groupuser-def-cmd
A valid CLI commands0
Power,fan,temperature related eventsEnvironmental
Inventory status eventsInventory
Events related to licensingLicense
Linecard related eventsLinecard-Hardware
Supervisor related eventsSupervisor-Hardware
Events related to syslog messages filed by port managerSyslog-group-port
Software related eventsSystem
User generated test eventsTest
Events related to ConfigurationConfiguration
Events related to DiagnosticDiagnostic
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)118
A Commandsalert-group user-def-cmd
Page 263
allocate-label all[no] allocate-label { all | route-map <rmap-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure label allocation for this AFallocate-label
Allocate labels for all routesall
Allocate labels for selected routesroute-map
Route-map namermap-name
Command Mode
• /exec/configure/router-bgp/router-bgp-af-ipv6 /exec/configure/router-bgp/router-bgp-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)119
A Commandsallocate-label all
Page 264
allocate-label option-b[no] allocate-label option-b
Syntax Description
(Optional) Negate a command or set its defaultsno
Allow allocation of labelsallocate-label
Allow allocation of option B labelsoption-b
Command Mode
• /exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-vpnv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)120
A Commandsallocate-label option-b
Page 265
allocate1 interface2allocate1 interface2 { <interface-id> [ force ] | unallocated-interfaces }
Syntax Description
Assign interfaces to vdcallocate1
Assign interface range to vdcinterface2
Assign interface range to vdcinterface-id
(Optional) forceforce
Best-effort trying to move all interfaces in the unallocated pool into thisvdc
unallocated-interfaces
Command Mode
• /exec/configure/vdc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)121
A Commandsallocate1 interface2
Page 266
allocate2 fcoe-vlan-range{ allocate2 fcoe-vlan-range [ <vlan_range> ] [ from vdcs <vdc_names> ] } | { no allocate2 fcoe-vlan-range[ <vlan_range> | { from vdcs <vdc_names> } ] }
Syntax Description
Negate a command or set its defaultsno
Assign interfaces to vdcallocate2
vlans reserved for FCoEfcoe-vlan-range
(Optional) vlans reserved for FCoEvlan_range
(Optional) which vdcs will be sharing ports with the FCoE vdcfrom
(Optional) which vdcs will be sharing ports with the FCoE vdcvdcs
(Optional) which vdcs will be sharing porst with the FCoE vdcvdc_names
Command Mode
• /exec/configure/vdc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)122
A Commandsallocate2 fcoe-vlan-range
Page 267
allocate3 shared interface3[no] allocate3 shared interface3 <sinterface-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Assign interfaces to vdcallocate3
Assign interface range to vdcinterface3
Assign interface range to vdcsinterface-id
Shared this port using the reserved FCoE vlansshared
Command Mode
• /exec/configure/vdc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)123
A Commandsallocate3 shared interface3
Page 268
allow-vni-in-ethertag[no] allow-vni-in-ethertag
Syntax Description
(Optional) Negate a command or set its defaultsno
Allow VNI in Ethernet Tag field in EVPN routeallow-vni-in-ethertag
Command Mode
• /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)124
A Commandsallow-vni-in-ethertag
Page 269
allow feature-set[no] allow feature-set <fs>
Syntax Description
(Optional) Negate a command or set its defaultsno
Used to change permisions inside a vdcallow
Change which feature-sets the user is able to enable inside the vdcfeature-set
installed feature-setsfs
Command Mode
• /exec/configure/vdc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)125
A Commandsallow feature-set
Page 270
allowas-in[ no | default ] allowas-in [ <allowas-in-cnt> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Accept as-path with my AS present in itallowas-in
(Optional) Number of occurrences of AS number, default is 3allowas-in-cnt
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv4/exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-link-state/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)126
A Commandsallowas-in
Page 271
allowas-in[ no | default ] allowas-in [ <allowas-in-cnt> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Accept as-path with my AS present in itallowas-in
(Optional) Number of occurrences of AS number, default is 3allowas-in-cnt
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)127
A Commandsallowas-in
Page 272
allowed-locators{ [ no ] allowed-locators { <rloc> | <rloc6> } + }
Syntax Description
(Optional) Negate a command or set its defaultsno
List of locators from LISP siteallowed-locators
IPv4 locator allowed in registered locator-setrloc
Command Mode
• /exec/configure/lisp-site /exec/configure/vrf/lisp-site
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)128
A Commandsallowed-locators
Page 273
allowed-vlansallowed-vlans { <allow-vlans> | add <add-vlans> | except <except-vlans> | remove <remove-vlans> | all }
Syntax Description
Set list of allowed vlans that can be used for interface configurationallowed-vlans
VLAN ID 1-4094 or range(s) like: 1-5, 10 or 2-5,7-19allow-vlans
add VLANs to the current listadd
VLAN ID 1-4094 or range(s) like: 1-5, 10 or 2-5,7-19add-vlans
all VLANs except the followingexcept
VLAN ID 1-4094 or range(s) like: 1-5, 10 or 2-5,7-19except-vlans
remove VLANs from the current listremove
VLAN ID 1-4094 or range(s) like: 1-5, 10 or 2-5,7-19remove-vlans
all VLANsall
Command Mode
• /exec/configure/vmt-conn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)129
A Commandsallowed-vlans
Page 274
amt flush-routes[no] amt flush-routes
Syntax Description
(Optional) Negate a command or set its defaultsno
AMT global configuration commandsamt
Remove routes when restarting AMTflush-routes
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)130
A Commandsamt flush-routes
Page 275
amt pseudo-interface{ { amt pseudo-interface <interface> } | { no amt pseudo-interface [ <interface> ] } }
Syntax Description
Negate a command or set its defaultsno
AMT global configuration commandsamt
Tunnel to relay for forwarding IGMP/MLD messagespseudo-interface
Intername name to used for AMT pseudo interfaceinterface
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)131
A Commandsamt pseudo-interface
Page 276
analytics cluster[no] analytics cluster <clustername> [ vrf <vrfName> ] [ srcIf <src_intf> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Feature Analyticsanalytics
Analytics clustercluster
Cluster nameclustername
(Optional) VRF Namevrf
(Optional) VRF namevrfName
(Optional) Source InterfacesrcIf
(Optional) Source Interfacesrc_intf
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)132
A Commandsanalytics cluster
Page 277
anonymous-id{ [ no ] anonymous-id <id> }
Syntax Description
anonymous identity associated with this profileanonymous-id
identity nameid
Command Mode
• /exec/configure/dot1x-cred
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)133
A Commandsanonymous-id
Page 278
append-after nextappend-after <index> { next-address [ loose | strict ] <ipaddr> | exclude-address <ipaddr> }
Syntax Description
Append additional entry after specified indexappend-after
Previous index numberindex
Specify the next address in the pathnext-address
(Optional) Target address is looseloose
(Optional) Target address is strictstrict
Exclude an address from subsequent partial path segmentsexclude-address
Enter IP address (A.B.C.D)ipaddr
Command Mode
• /exec/configure/te/expl-path
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)134
A Commandsappend-after next
Page 279
apply profile[no] apply profile { <all_conf_profile_name> } [ include-profile <include-profile> ] [ { param-instance<plistinst> | include-instance <plistinst> } + ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Apply a config-profileapply
Apply a config-profileprofile
Enter the name of the profileall_conf_profile_name
(Optional) Enter the name of the param-instanceparam-instance
(Optional) Enter the name of the instanceplistinst
(Optional) Enter the name of the include profileinclude-profile
(Optional) Enter the name of the include profileinclude-profile
(Optional) Enter the param-instance corresponding to the first includedprofile
include-instance
(Optional) Enter the name of the include instanceplistinst
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)135
A Commandsapply profile
Page 280
area authentication[no] area <area-id-ip> authentication [ message-digest ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Enable authentication for the areaauthentication
(Optional) Use message-digest authenticationmessage-digest
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)136
A Commandsarea authentication
Page 281
area authenticationarea <area-id-ip> authentication { disable | ipsec spi <spi_id> { md5 <akey> | sha1 <akey> } } | no area<area-id-ip> authentication { disable | ipsec spi <spi_id> }
Syntax Description
Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Enable Authenticationauthentication
Disable Authenticationdisable
IPSecipsec
Security Parameter Indexspi
SPI Valuespi_id
Use the MD5 algorithimmd5
Authentication Keyakey
Use the SHA1 algorithimsha1
Authentication Keyakey
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)137
A Commandsarea authentication
Page 282
area default-cost{ { area <area-id-ip> default-cost <cost> } | { no area <area-id-ip> default-cost [ <cost> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Specify default-cost for default summary LSAdefault-cost
Cost valuecost
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)138
A Commandsarea default-cost
Page 283
area default-cost{ { area <area-id-ip> default-cost <cost> } | { no area <area-id-ip> default-cost [ <cost> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Specify default-cost for default inter-area-prefix LSAdefault-cost
Cost valuecost
Command Mode
• /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)139
A Commandsarea default-cost
Page 284
area filter-list route-map in{ area <area-id-ip> filter-list route-map { <policy-name> | <rtr_pol_name> } { in | out } } | { no area<area-id-ip> filter-list route-map { <policy-name> | <rtr_pol_name> } [ in | out ] }
Syntax Description
Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Filter prefixes between OSPF areasfilter-list
Name of filter policyroute-map
Route-map namepolicy-name
An existing routing-rules policyrtr_pol_name
Filter networks sent to this areain
Filter networks sent from this areaout
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)140
A Commandsarea filter-list route-map in
Page 285
area filter-list route-map in{ area <area-id-ip> filter-list route-map { <policy-name> | <rtr_pol_name> } { in | out } } | { no area<area-id-ip> filter-list route-map { <policy-name> | <rtr_pol_name> } [ in | out ] }
Syntax Description
Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Filter prefixes between OSPF areasfilter-list
Name of filter policyroute-map
Route-map namepolicy-name
An existing routing-rules policyrtr_pol_name
Filter networks sent to this areain
Filter networks sent from this areaout
Command Mode
• /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)141
A Commandsarea filter-list route-map in
Page 286
area nssa[no] area <area-id-ip> nssa { [ no-summary ] [ no-redistribution ] [ default-information-originate [ route-map<policy-name> ] ] } +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Configure area as NSSAnssa
(Optional) Do not send summary LSAs into NSSA areano-summary
(Optional) Do not send redistributed LSAs into NSSA areano-redistribution
(Optional) Originate Type-7 default LSA into NSSA areadefault-information-originate
(Optional) Policy to control distribution of default routeroute-map
(Optional) Route-map namepolicy-name
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)142
A Commandsarea nssa
Page 287
area nssa[no] area <area-id-ip> nssa { [ no-summary ] [ no-redistribution ] [ default-information-originate [ route-map<policy-name> ] ] } +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Configure area as NSSAnssa
(Optional) Do not send summary LSAs into NSSA areano-summary
(Optional) Do not send redistributed LSAs into NSSA areano-redistribution
(Optional) Originate Type-7 default LSA into NSSA areadefault-information-originate
(Optional) Policy to control distribution of default routeroute-map
(Optional) Route-map namepolicy-name
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)143
A Commandsarea nssa
Page 288
area nssa translate type7 always never supress-fa{ area <area-id-ip> nssa translate type7 { always [ supress-fa ] | never | supress-fa } } | { no area <area-id-ip>nssa translate type7 [ always [ supress-fa ] | never | supress-fa ] }
Syntax Description
Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Configure area as NSSAnssa
Translate LSAtranslate
From Type 7 to Type 5type7
Always translate LSAsalways
Never translate LSAsnever
(Optional) Supress forwarding address in translated LSAssupress-fa
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)144
A Commandsarea nssa translate type7 always never supress-fa
Page 289
area nssa translate type7 always never supress-fa{ area <area-id-ip> nssa translate type7 { always [ supress-fa ] | never | supress-fa } } | { no area <area-id-ip>nssa translate type7 [ always [ supress-fa ] | never | supress-fa ] }
Syntax Description
Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Configure area as NSSAnssa
Translate LSAtranslate
From NSSA-external (Type 7) to AS-external (Type 5)type7
Always translate LSAsalways
Never translate LSAsnever
(Optional) Supress forwarding address in translated LSAssupress-fa
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)145
A Commandsarea nssa translate type7 always never supress-fa
Page 290
area range[no] area <area-id-ip> range { <ip-dest> <ip-mask> | <ip-prefix> } { [ not-advertise ] [ cost <conf-cost> ] }+
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Configure an address range for an arearange
IP prefix format: i.i.i.iip-dest
IP network mask format: m.m.m.mip-mask
IP prefix format: x.x.x.x/mlip-prefix
(Optional) Suppress advertising the specified rangenot-advertise
(Optional) Cost to use for rangecost
(Optional) Cost valueconf-cost
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)146
A Commandsarea range
Page 291
area range[no] area <area-id-ip> range <ipv6-prefix> { [ not-advertise ] [ cost <conf-cost> ] } +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Configure an address range for an arearange
(Optional) Suppress advertising the specified rangenot-advertise
(Optional) Cost to use for rangecost
(Optional) Cost valueconf-cost
Command Mode
• /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)147
A Commandsarea range
Page 292
area sham-link[no] area <area-id-ip> sham-link <source-address> <dest-address>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Define a sham link and its parameterssham-link
IP addr associated with sham-link sourcesource-address
IP addr associated with sham-link destinationdest-address
Command Mode
• /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)148
A Commandsarea sham-link
Page 293
area stub[no] area <area-id-ip> stub [ no-summary ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Configure area as a stubstub
(Optional) Prevent ABR from sending summary LSAs into stub areano-summary
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)149
A Commandsarea stub
Page 294
area stub[no] area <area-id-ip> stub [ no-summary ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Configure area as a stubstub
(Optional) Prevent ABR from sending summary LSAs into stub areano-summary
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)150
A Commandsarea stub
Page 295
area virtual-link[no] area <area-id-ip> virtual-link <routerid>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Define a virtual link and its parametersvirtual-link
Router ID associated with virtual link neighborrouterid
Command Mode
• /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)151
A Commandsarea virtual-link
Page 296
area virtual-link[no] area <area-id-ip> virtual-link <routerid>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Define a virtual link and its parametersvirtual-link
Router ID associated with virtual link neighborrouterid
Command Mode
• /exec/configure/router-ospf3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)152
A Commandsarea virtual-link
Page 297
area virtual-link[no] area <area-id-ip> virtual-link <routerid>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Define a virtual link and its parametersvirtual-link
Router ID associated with virtual link neighborrouterid
Command Mode
• /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)153
A Commandsarea virtual-link
Page 298
area virtual-link[no] area <area-id-ip> virtual-link <routerid>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Define a virtual link and its parametersvirtual-link
Router ID associated with virtual link neighborrouterid
Command Mode
• /exec/configure/router-ospf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)154
A Commandsarea virtual-link
Page 299
arp access-list[no] arp access-list <name>
Syntax Description
(Optional) Negate a command or set its defaultsno
ARP access-list configuration commandsarp
Configure access listaccess-list
List namename
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)155
A Commandsarp access-list
Page 300
as-format asdotas-format asdot | no as-format
Syntax Description
Negate a command or set its defaultsno
Configure the router's Autonomous system number (ASN) notationas-format
Specifies the Autonomous system number (ASN) notation to asdotformat
asdot
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)156
A Commandsas-format asdot
Page 301
as-override[ no | default ] as-override
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Override matching AS-number while sending updateas-override
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv4/exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)157
A Commandsas-override
Page 302
assign interface shared{ assign interface { <sdn-eth-intf-list> | <sdn-pc-intf-list> } shared | no assign interface { <sdn-eth-intf-list>| <sdn-pc-intf-list> } }
Syntax Description
Negate a command or set its defaultsno
Assign resourceassign
Resource of interface typeinterface
List of Interfacessdn-eth-intf-list
List of Interfacessdn-pc-intf-list
Share interface with controllershared
Command Mode
• /exec/configure/controller-type
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)158
A Commandsassign interface shared
Page 303
assign vlan dedicated{ assign vlan <sdn-id> dedicated | no assign vlan <sdn-id> }
Syntax Description
Negate a command or set its defaultsno
Assign reservationassign
Controller VLANsvlan
vlan ID 2-4093 or range(s): 1-5, 10 or 2-5,7-19sdn-id
Dedicated VLANsdedicated
Command Mode
• /exec/configure/controller-type
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)159
A Commandsassign vlan dedicated
Page 304
assign vrf prefix number dedicated{ assign vrf prefix <prefix-name> number <number-of-vrfs> dedicated | no assign vrf }
Syntax Description
Negate a command or set its defaultsno
Assign reservationassign
VRFsvrf
VRF prefixprefix
String description of the prefixprefix-name
Number of VRFsnumber
VRF ID range from 1 to 4095number-of-vrfs
Dedicated VRFsdedicated
Command Mode
• /exec/configure/controller-type
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)160
A Commandsassign vrf prefix number dedicated
Page 305
attach console moduleattach console module <module>
Syntax Description
Connect to a specific linecardattach
Connect to the consoleconsole
Connect to the module consolemodule
Enter module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)161
A Commandsattach console module
Page 306
attach moduleattach module <module>
Syntax Description
Connect to a specific linecardattach
Module number of the linecardmodule
Enter module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)162
A Commandsattach module
Page 307
attach module nodeattach module <module> node <i0>
Syntax Description
Connect to a specific linecardattach
Module number of the linecardmodule
Enter module numbermodule
Avanti node number on the linecardnode
i0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)163
A Commandsattach module node
Page 308
attach module portattach module <module> port <i0>
Syntax Description
Connect to a specific linecardattach
Module number of the linecardmodule
Enter module numbermodule
Port number on the linecardport
i0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)164
A Commandsattach module port
Page 309
auth-mechanism plain[no] auth-mechanism { plain }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set the authentication mechanismauth-mechanism
Set the authentication mechanism as plain(default)plain
Command Mode
• /exec/configure/ldap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)165
A Commandsauth-mechanism plain
Page 310
authentication-check[no] authentication-check
Syntax Description
(Optional) Negate a command or set its defaultsno
Check authentication on received LSP/CSNP/PSNP'sauthentication-check
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)166
A Commandsauthentication-check
Page 311
authentication-check[no] authentication-check
Syntax Description
(Optional) Negate a command or set its defaultsno
Check authentication on received LSP/CSNP/PSNP'sauthentication-check
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)167
A Commandsauthentication-check
Page 312
authentication-check level-1[no] authentication-check level-1
Syntax Description
(Optional) Negate a command or set its defaultsno
Check authentication on received LSP/CSNP/PSNP'sauthentication-check
Specify authentication check for level-1 LSP, CSNP and PSNPlevel-1
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)168
A Commandsauthentication-check level-1
Page 313
authentication-check level-2[no] authentication-check level-2
Syntax Description
(Optional) Negate a command or set its defaultsno
Check authentication on received LSP/CSNP/PSNP'sauthentication-check
Specify authentication check for level-2 LSP, CSNP and PSNPlevel-2
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)169
A Commandsauthentication-check level-2
Page 314
authentication-key{ [ no ] authentication-key <key> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Authentication key used by LISP siteauthentication-key
SHA-1 passwordkey
Command Mode
• /exec/configure/lisp-site /exec/configure/vrf/lisp-site
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)170
A Commandsauthentication-key
Page 315
authentication-key{ { authentication-key <key> } | { no authentication-key [ <key> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure the authentication key for the virtual-linkauthentication-key
Authentication keykey
Command Mode
• /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)171
A Commandsauthentication-key
Page 316
authentication-key{ { authentication-key <key> } | { no authentication-key [ <key> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure the authentication key for the sham-linkauthentication-key
Authentication keykey
Command Mode
• /exec/configure/router-ospf/vrf/router-ospf-slink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)172
A Commandsauthentication-key
Page 317
authentication-type cleartext{ authentication-type { cleartext | md5 } | no authentication-type [ { cleartext | md5 } ] }
Syntax Description
Negate a command or set its defaultsno
Set authentication typeauthentication-type
Cleartextcleartext
HMAC-MD5md5
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)173
A Commandsauthentication-type cleartext
Page 318
authentication-type cleartext{ authentication-type { cleartext | md5 } <level> | no authentication-type [ { cleartext | md5 } ] <level> }
Syntax Description
Negate a command or set its defaultsno
Set authentication typeauthentication-type
Cleartextcleartext
HMAC-MD5md5
IS-IS levellevel
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)174
A Commandsauthentication-type cleartext
Page 319
authentication-type cleartext{ authentication-type { cleartext | md5 } | no authentication-type [ { cleartext | md5 } ] }
Syntax Description
Negate a command or set its defaultsno
Set authentication typeauthentication-type
Cleartextcleartext
HMAC-MD5md5
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)175
A Commandsauthentication-type cleartext
Page 320
authenticationauthentication { disable | ipsec spi <spi_id> { md5 <akey> | sha1 <akey> } } | no authentication { disable |ipsec spi <spi_id> }
Syntax Description
Negate a command or set its defaultsno
Enable Authenticationauthentication
Disable Authenticationdisable
IPSecipsec
Security Parameter Indexspi
SPI Valuespi_id
Use the MD5 algorithimmd5
Authentication Keyakey
Use the SHA1 algorithimsha1
Authentication Keyakey
Command Mode
• /exec/configure/router-ospf3/router-ospf3-vlink /exec/configure/router-ospf3/vrf/router-ospf3-vlink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)176
A Commandsauthentication
Page 321
authenticationauthentication { [ text ] <secret> | md5 { key-chain <chain-name> | key-string [ 0 | 7 ] <key-name> [compatibility ] [ timeout <sec> ] } } | no authentication
Syntax Description
Negate a command or set its defaultsno
Authenticationauthentication
(Optional) Plain text authenticationtext
Plain text authentication stringsecret
Use MD5 authenticationmd5
Set key chainkey-chain
Name of key-chainchain-name
Set key stringkey-string
(Optional) Specifies an UNENCRYPTED key string will follow0
(Optional) Specifies a HIDDEN key string will follow7
Key string (64 chars max)key-name
(Optional) Operate in compatibility mode forMD5 type-7 authenticationcompatibility
(Optional) Set timeouttimeout
(Optional) (0-32767)Timeout until only accepting new key (seconds)sec
Command Mode
• /exec/configure/if-eth-any/hsrp_ipv4 /exec/configure/if-eth-any/hsrp_ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)177
A Commandsauthentication
Page 322
authenticationauthentication { ipsec spi <spi_id> { md5 <akey> | sha1 <akey> } } | no authentication ipsec spi <spi_id>
Syntax Description
Negate a command or set its defaultsno
Enable Authenticationauthentication
IPSecipsec
Security Parameter Indexspi
SPI Valuespi_id
Use the MD5 algorithimmd5
Authentication Keyakey
Use the SHA1 algorithimsha1
Authentication Keyakey
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)178
A Commandsauthentication
Page 323
authentication[no] authentication { { key-chain <chain> } | { mode md5 } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configures EIGRP authentication subcommandsauthentication
key-chainkey-chain
name of key-chainchain
modemode
Keyed message digestmd5
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)179
A Commandsauthentication
Page 324
authentication[no] authentication [ message-digest | null ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Authentication on the vlinkauthentication
(Optional) Use message-digest authenticationmessage-digest
(Optional) Use null(disable) authenticationnull
Command Mode
• /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)180
A Commandsauthentication
Page 325
authentication[no] authentication [ message-digest | null ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Authentication on the slinkauthentication
(Optional) Use message-digest authenticationmessage-digest
(Optional) Use null(disable) authenticationnull
Command Mode
• /exec/configure/router-ospf/vrf/router-ospf-slink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)181
A Commandsauthentication
Page 326
authentication bind[no] authentication { bind-first [ append-with-basedn <s1> ] | compare [ password-attribute <s0> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set the authentication methodauthentication
Set the authentication method to bind-firstbind-first
(Optional) Change the default value (cn=$userid)append-with-basedn
(Optional) append with dn values1
Change the default attributecompare
(Optional) Change the default password attribute (userPassword)password-attribute
(Optional) password attributes0
Command Mode
• /exec/configure/ldap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)182
A Commandsauthentication bind
Page 327
authentication challenge[no] authentication [ neighbor <nbr> ] challenge
Syntax Description
Configure RSVP neighbor cryptographic authenticationauthentication
(Optional) Configure RSVP neighborneighbor
(Optional) RSVP Neighbor addressnbr
Perform challenge/response handshake with new RSVP neighborschallenge
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)183
A Commandsauthentication challenge
Page 328
authentication key-chainauthentication [ neighbor <nbr> ] key-chain <key-chain-name> | no authentication [ neighbor <nbr> ] key-chain
Syntax Description
Configure RSVP neighbor cryptographic authenticationauthentication
(Optional) Configure RSVP neighborneighbor
(Optional) RSVP Neighbor addressnbr
Authentication password key-chainkey-chain
Key-chain namekey-chain-name
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)184
A Commandsauthentication key-chain
Page 329
authentication key-chain{ authentication key-chain <auth-keychain> <level> | no authentication key-chain [ <auth-keychain> ] <level>}
Syntax Description
Negate a command or set its defaultsno
Set authentication keychain stringauthentication
Set authentication keychain stringkey-chain
authentication keychainauth-keychain
IS-IS levellevel
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)185
A Commandsauthentication key-chain
Page 330
authentication key-chain{ authentication key-chain <keychain> } | { no authentication key-chain [ <keychain> ] }
Syntax Description
Negate a command or set its defaultsno
Authentication on the vlinkauthentication
Authentication password key-chainkey-chain
Key-chain namekeychain
Command Mode
• /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)186
A Commandsauthentication key-chain
Page 331
authentication key-chain{ authentication key-chain <keychain> } | { no authentication key-chain [ <keychain> ] }
Syntax Description
Negate a command or set its defaultsno
Authentication on the slinkauthentication
Authentication password key-chainkey-chain
Key-chain namekeychain
Command Mode
• /exec/configure/router-ospf/vrf/router-ospf-slink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)187
A Commandsauthentication key-chain
Page 332
authentication key-chain{ authentication key-chain <auth-keychain> | no authentication key-chain [ <auth-keychain> ] }
Syntax Description
Negate a command or set its defaultsno
Set authentication keychain stringauthentication
Set authentication keychain stringkey-chain
authentication keychainauth-keychain
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)188
A Commandsauthentication key-chain
Page 333
authentication key-chain{ authentication key-chain <auth-keychain> | no authentication key-chain [ <auth-keychain> ] }
Syntax Description
Negate a command or set its defaultsno
Set authentication keychain stringauthentication
Set authentication keychain stringkey-chain
authentication keychainauth-keychain
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)189
A Commandsauthentication key-chain
Page 334
authentication lifetime[no] authentication [ neighbor <nbr> ] lifetime <time>
Syntax Description
Configure RSVP neighbor cryptographic authenticationauthentication
(Optional) Configure RSVP neighborneighbor
(Optional) RSVP Neighbor addressnbr
Maximum lifetime of neighbor authentication statelifetime
Lifetime value(in seconds)time
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)190
A Commandsauthentication lifetime
Page 335
authentication text{ authentication text <authentication_pwd> | no authentication [ text <authentication_pwd> ] }
Syntax Description
Negate a command or set its defaultsno
Select authentication methodauthentication
Set the authentication password (8 char max)text
authentication_pwd
Command Mode
• /exec/configure/if-eth-any/vrrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)191
A Commandsauthentication text
Page 336
authentication type md5[no] authentication [ neighbor <nbr> ] type { md5 | sha-1 }
Syntax Description
Configure RSVP neighbor cryptographic authenticationauthentication
(Optional) Configure RSVP neighborneighbor
(Optional) RSVP Neighbor addressnbr
Type of authentication algorithmtype
RSA Message Digest 5 hash algorithm (default)md5
NIST Secure Hash Algorithm 1sha-1
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)192
A Commandsauthentication type md5
Page 337
authentication window-size[no] authentication [ neighbor <nbr> ] window-size <value>
Syntax Description
Configure RSVP neighbor cryptographic authenticationauthentication
(Optional) Configure RSVP neighborneighbor
(Optional) RSVP Neighbor addressnbr
Receive window size for authenticated messageswindow-size
Maximum number of messages allowed in receive windowvalue
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)193
A Commandsauthentication window-size
Page 338
auto-bw[no] auto-bw | auto-bw [ { [ collect-bw | frequency <sec> ] + } | { [ frequency <sec> | min-bw <min-kbps> |max-bw <max-kbps> ] + } ]
Syntax Description
Negate a command or set its defaultsno
Specify mpls tunnel should automatically change bwauto-bw
(Optional) Just collect Bandwidth info on this tunnelcollect-bw
(Optional) Frequency to change tunnel BWfrequency
(Optional) seconds between applying auto-bwsec
(Optional) Set the Maximum Bandwidth for auto-bw on this tunnelmax-bw
(Optional) Maximum kb/s that tunnel can be auto set tomax-kbps
(Optional) Set the Minimum Bandwidth for auto-bw on this tunnelmin-bw
(Optional) Min kb/s that tunnel can be auto set tomin-kbps
Command Mode
• /exec/configure/if-te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)194
A Commandsauto-bw
Page 339
auto-bw[no] auto-bw | auto-bw [ { [ collect-bw | frequency <sec> ] + } | { [ frequency <sec> | min-bw <min-kbps> |max-bw <max-kbps> ] + } ]
Syntax Description
Negate a command or set its defaultsno
Specify automatic bandwidth configurationauto-bw
(Optional) Just collect bandwidth infocollect-bw
(Optional) frequency to change LSP bandwidthfrequency
(Optional) seconds between applying auto-bwsec
(Optional) Set the maximum bandwidth for auto-bwmax-bw
(Optional) Maximum bandwidth to apply (kbps)max-kbps
(Optional) Set the minimum bandwidth for auto-bwmin-bw
(Optional) Minimum bandwidth to apply (kbps)min-kbps
Command Mode
• /exec/configure/te/lsp-attr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)195
A Commandsauto-bw
Page 340
auto-bw timers frequency[no] auto-bw timers { frequency } | auto-bw timers { frequency <sec> }
Syntax Description
Negate a command or set its defaultsno
auto-bw parametersauto-bw
Enable auto-bw timerstimers
Interval between auto-bw data collectionfrequency
Seconds between auto-bw data collectionsec
Command Mode
• /exec/configure/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)196
A Commandsauto-bw timers frequency
Page 341
auto-cost reference-bandwidthauto-cost reference-bandwidth { <ref-bw-mbps> [ Mbps ] | <ref-bw-gbps> Gbps } | no auto-costreference-bandwidth [ <ref-bw-mbps> [ Mbps ] | <ref-bw-gbps> Gbps ]
Syntax Description
Negate a command or set its defaultsno
Calculate OSPF cost according to bandwidthauto-cost
Reference bandwidth used to assign OSPF costreference-bandwidth
(Optional) Specify rate in MbpsMbps
Specify rate in GbpsGbps
Rate in Mbps (bandwidth) (Default)ref-bw-mbps
Rate in Gbps (bandwidth)ref-bw-gbps
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)197
A Commandsauto-cost reference-bandwidth
Page 342
auto-cost reference-bandwidthauto-cost reference-bandwidth { <ref-bw-mbps> [ Mbps ] | <ref-bw-gbps> Gbps } | no auto-costreference-bandwidth [ <ref-bw-mbps> [ Mbps ] | <ref-bw-gbps> Gbps ]
Syntax Description
Negate a command or set its defaultsno
Calculate OSPFv3 cost according to bandwidthauto-cost
Reference bandwidth used to assign OSPFv3 costreference-bandwidth
(Optional) Specify rate in MbpsMbps
Specify rate in GbpsGbps
Rate in Mbps (bandwidth) (Default)ref-bw-mbps
Rate in Gbps (bandwidth)ref-bw-gbps
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)198
A Commandsauto-cost reference-bandwidth
Page 343
auto-recoveryauto-recovery [ reload-delay <time-out> ] | no auto-recovery [ reload-delay <time-out> ]
Syntax Description
Negate a command or set its defaultsno
vPC settings to enable auto recovery if peer is presumed non-operationalauto-recovery
(Optional) Duration to wait before assuming peer dead and restoringvpcs
reload-delay
(Optional) Time-out for restoring vPC links (in seconds)time-out
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)199
A Commandsauto-recovery
Page 344
auto-remap-replication-servers[no] auto-remap-replication-servers
Syntax Description
(Optional) Negate a command or set its defaultsno
Automatically re-map replication servers on every replication serveradd
auto-remap-replication-servers
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)200
A Commandsauto-remap-replication-servers
Page 345
autonomous-system{ { autonomous-system <local-as> } | { no autonomous-system [ <local-as> ] } }
Syntax Description
Negate a command or set its defaultsno
Specify AS number for Address Familyautonomous-system
Local AS numberlocal-as
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)201
A Commandsautonomous-system
Page 346
autoroute announce[no] autoroute announce
Syntax Description
(Optional) Negate a command or set its defaultsno
parameters for IGP routing over tunnelautoroute
announce tunnel to IGPannounce
Command Mode
• /exec/configure/if-te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)202
A Commandsautoroute announce
Page 347
autoroute metric[no] autoroute metric | autoroute metric { <value> | relative <rel-value> }
Syntax Description
Negate a command or set its defaultsno
parameters for IGP routing over tunnelautoroute
Specify mpls tunnel metricmetric
Set tunnel metric for autoroutesvalue
Adjust tunnel metric for autoroutes relative to IGPrelative
Relative metric valuerel-value
Command Mode
• /exec/configure/if-te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)203
A Commandsautoroute metric
Page 348
autostate[no] autostate
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable or disable autostate for interface-vlanautostate
Command Mode
• /exec/configure/if-vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)204
A Commandsautostate
Page 349
autovlan enable[no] autovlan enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Automatic creation/deletion of VLANsautovlan
Enable auto creation/deletion of VLANsenable
Command Mode
• /exec/configure/vmt-conn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)205
A Commandsautovlan enable
Page 350
awk| awk <expr>
Syntax Description
Pipe command output to filter|
Mini AWKawk
Edition command (script)expr
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)206
A Commandsawk
Page 351
B Commands
• backoff, on page 210• backup-bw, on page 211• bandwidth, on page 212• bandwidth, on page 213• bandwidth, on page 214• bandwidth, on page 215• bandwidth, on page 216• bandwidth, on page 217• bandwidth, on page 218• bandwidth, on page 219• bandwidth, on page 220• bandwidth kbps mbps gbps, on page 221• banner exec, on page 222• banner motd, on page 223• bcm-shell module, on page 224• bcm-shell module, on page 225• beacon, on page 226• begin exclude include end, on page 227• bestpath, on page 228• bfd-app session auto-expiry timeout, on page 229• bfd-app session remove, on page 230• bfd-app session src-ip dest intf, on page 231• bfd, on page 232• bfd, on page 233• bfd, on page 234• bfd, on page 235• bfd, on page 236• bfd, on page 237• bfd, on page 238• bfd authentication interop, on page 239• bfd authentication key-id key, on page 240• bfd echo-interface, on page 241• bfd echo-rx-interval, on page 242
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)207
Page 352
• bfd echo, on page 243• bfd interval, on page 244• bfd interval, on page 245• bfd interval min_rx multiplier, on page 246• bfd interval min_rx multiplier, on page 247• bfd move-session target, on page 248• bfd multihop authentication key-id key bfd multihop authentication, on page 249• bfd multihop hosting-linecard add module, on page 250• bfd multihop hosting-linecard add module, on page 251• bfd multihop interval, on page 252• bfd multihop interval min_rx multiplier, on page 253• bfd multihop interval min_rx multiplier, on page 254• bfd neighbor src-ip dest, on page 255• bfd optimize subinterface, on page 256• bfd per-link, on page 257• bfd session-store remove client, on page 258• bfd session-store source-ip dest-ip intf client, on page 259• bfd session state state, on page 260• bfd slow-timer, on page 261• bfd startup-timer bfd startup-timer, on page 262• bfshell, on page 263• bfshell cmd, on page 264• bfshell module, on page 265• bfshell module cmd, on page 266• binary-location, on page 267• bind interface, on page 268• bind mac-address, on page 269• blink, on page 270• bloggerd live-process-core sap, on page 271• bloggerd log-dump all, on page 272• bloggerd log-dump once log-buffer sap event-history, on page 273• bloggerd log-dump once pss uuid, on page 274• bloggerd log-throttle, on page 275• bloggerd log-transfer, on page 276• bloggerd log-transfer, on page 277• bloggerd parse log-buffer file, on page 278• bloggerd parse log-buffer file sap, on page 279• bloggerd parse pss file, on page 280• bmp-activate-server, on page 281• bmp-server, on page 282• boot-install nxos, on page 283• boot-order, on page 284• boot, on page 285• boot aci, on page 286• boot auto-copy, on page 287• boot kickstart, on page 288
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)208
B Commands
Page 353
• boot mode docker_cluster, on page 289• boot mode docker_standalone, on page 290• boot mode lxc, on page 291• boot nxos, on page 292• boot nxos sup-1, on page 293• boot nxos sup-1 sup-2, on page 294• boot nxos sup-2, on page 295• boot order bootflash, on page 296• boot order pxe, on page 297• boot poap enable, on page 298• boot system, on page 299• bootmode boot, on page 300• bootmode extruntime, on page 301• bootmode hitless, on page 302• bootmode module, on page 303• bootmode nodiagruntime, on page 304• bootmode runtime, on page 305• buffer-boost, on page 306• buffer-delete, on page 307• buffer-move, on page 308• burst-detect enable, on page 309• burst-detect rise-threshold bytes fall-threshold bytes2, on page 310
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)209
B Commands
Page 354
backoffbackoff <initial-backoff> <maximum-backoff> | no backoff
Syntax Description
Negate a command or set its defaultsno
Set LDP session backoff parametersbackoff
Initial session backoff time (seconds)initial-backoff
Maximum session backoff time (seconds)maximum-backoff
Command Mode
• /exec/configure/ldp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)210
B Commandsbackoff
Page 355
backup-bwbackup-bw { <kbps> } | no backup-bw
Syntax Description
Negate a command or set its defaultsno
Represents bw for Fast Reroute backupbackup-bw
Amount of allocatable backup bw, any lsp may usekbps
Command Mode
• /exec/configure/if-te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)211
B Commandsbackup-bw
Page 356
bandwidthbandwidth <bandwidth_val> | no bandwidth
Syntax Description
Negate a command or set its defaultsno
Set bandwidth informational parameterbandwidth
Bandwidth in kilobitsbandwidth_val
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)212
B Commandsbandwidth
Page 357
bandwidthbandwidth <bandwidth_val> | no bandwidth
Syntax Description
Negate a command or set its defaultsno
Set bandwidth informational parameterbandwidth
Bandwidth in kilobitsbandwidth_val
Command Mode
• /exec/configure/if-any-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)213
B Commandsbandwidth
Page 358
bandwidth[no] bandwidth { { xxx <bw-value> [ bps | kbps | mbps | gbps ] | percent <percentage> } | { remaining percent<rem-perc> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Specify bandwidth for the classbandwidth
xxxxxx
(Optional) Bits per secondbps
(Optional) Kilo bits per secondkbps
(Optional) Mega bits per secondmbps
(Optional) Giga bits per secondgbps
Percentage of available bandwidthpercent
Value in percentagepercentage
% of remaining bandwidthremaining
Value in percentagerem-perc
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)214
B Commandsbandwidth
Page 359
bandwidthbandwidth { <bandwidth_val> | inherit [ <inherit_val> ] } | no bandwidth { [ <bandwidth_val> ] | inherit [<inherit_val> ] }
Syntax Description
Negate a command or set its defaultsno
Set bandwidth informational parameterbandwidth
Bandwidth in kilobitsbandwidth_val
Specify that bandwidth is inheritedinherit
(Optional) Bandwidth in kilobitsinherit_val
Command Mode
• /exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p /exec/configure/if-port-channel-sub/exec/configure/if-ethernet-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)215
B Commandsbandwidth
Page 360
bandwidthbandwidth { <bandwidth_val> | inherit [ <inherit_val> ] } | no bandwidth { [ <bandwidth_val> ] | inherit [<inherit_val> ] }
Syntax Description
Negate a command or set its defaultsno
Set bandwidth informational parameterbandwidth
Bandwidth in kilobitsbandwidth_val
Specify that bandwidth is inheritedinherit
(Optional) Bandwidth in kilobitsinherit_val
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-gig-ether-sub/exec/configure/if-remote-ethernet-sub
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)216
B Commandsbandwidth
Page 361
bandwidthbandwidth { <bandwidth_val> | inherit [ <inherit_val> ] } | no bandwidth { [ <bandwidth_val> ] | inherit [<inherit_val> ] }
Syntax Description
Negate a command or set its defaultsno
Set bandwidth informational parameterbandwidth
Specify that bandwidth is inheritedinherit
Command Mode
• /exec/configure/if-eth-port-channel /exec/configure/if-port-channel-range/exec/configure/if-port-channel-sub /exec/configure/if-eth-port-channel-switch/exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)217
B Commandsbandwidth
Page 362
bandwidth[no] bandwidth { { <bw-value> [ bps | kbps | mbps | gbps ] | percent <percentage> } | { remaining percent<rem-perc> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Specify bandwidth for the classbandwidth
(Optional) Bits per secondbps
(Optional) Kilo bits per secondkbps
(Optional) Mega bits per secondmbps
(Optional) Giga bits per secondgbps
Percentage of available bandwidthpercent
Value in percentagepercentage
% of remaining bandwidthremaining
Value in percentagerem-perc
Command Mode
• /exec/configure/policy-map/type/plc/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)218
B Commandsbandwidth
Page 363
bandwidth[no] bandwidth | bandwidth { <bw> }
Syntax Description
Negate a command or set its defaultsno
Specify LSP bandwidthbandwidth
bandwidth requirement in kbpsbw
Command Mode
• /exec/configure/te/lsp-attr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)219
B Commandsbandwidth
Page 364
bandwidth[no] bandwidth | bandwidth { <kbps> }
Syntax Description
Negate a command or set its defaultsno
tunnel bandwidth requirementbandwidth
bandwidth requirement in kbpskbps
Command Mode
• /exec/configure/if-te /exec/configure/tunnel-te/cbts-member
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)220
B Commandsbandwidth
Page 365
bandwidth kbps mbps gbps{ { bandwidth { <val_kbps> kbps | <val_mbps> mbps | <val_gbps> gbps } } | { dscp <dscp_val> } } | { no{ bandwidth | dscp } }
Syntax Description
Negate a command or set its defaultsno
Bandwidth per flowbandwidth
Per Flow Bandwidth in Kbpsval_kbps
Bandwidth value in Kbpskbps
Per Flow Bandwidth in Mbpsval_mbps
Bandwidth value in Mbpsmbps
Per Flow Bandwidth in Gbpsval_gbps
Bandwidth value in Gbpsgbps
DSCP per flowdscp
Per Flow DSCPdscp_val
Command Mode
• /exec/configure/nbm-flow-policy/attr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)221
B Commandsbandwidth kbps mbps gbps
Page 366
banner exec{ banner exec <lineNo> } | { no banner exec }
Syntax Description
Negate a command or set its defaultsno
Configure banner messagebanner
Configure banner exec messageexec
Delimiter char (first char is delimiter char) followed by message endingwith delimiter
lineNo
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)222
B Commandsbanner exec
Page 367
banner motd{ banner motd <line> } | { no banner motd }
Syntax Description
Negate a command or set its defaultsno
Configure banner messagebanner
Configure banner motd messagemotd
Delimiter char (Very first char is delimiter char) followed by messageending with delimiter
line
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)223
B Commandsbanner motd
Page 368
bcm-shell modulebcm-shell module <module> <quoted-cmd>
Syntax Description
bcm shell/cmdbcm-shell
Module number of the linecardmodule
Enter module numbermodule
the command to run on bcm-shellquoted-cmd
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)224
B Commandsbcm-shell module
Page 369
bcm-shell modulebcm-shell module <module>
Syntax Description
bcm shell/cmdbcm-shell
Module number of the linecardmodule
Enter module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)225
B Commandsbcm-shell module
Page 370
beacon[no] beacon
Syntax Description
(Optional) Negate a command or set its defaultsno
Disable/enable the beacon for an interfacebeacon
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)226
B Commandsbeacon
Page 371
begin exclude include end| { begin | exclude | include | end } [ -i | -x ] + <expr> [ next <num> | prev <num> ] +
Syntax Description
Pipe command output to filter|
Begin with the line that matchesbegin
Exclude lines that matchexclude
Include lines that matchinclude
End with the line that matchesend
(Optional) Ignore case difference when comparing strings-i
(Optional) Print only lines where the match is a whole line-x
Search for the expressionexpr
(Optional) Print <num> lines of context after every matching linenext
(Optional) Print <num> lines of context before every matching lineprev
(Optional) Print <num> lines of contextnum
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)227
B Commandsbegin exclude include end
Page 372
bestpath[no] bestpath { always-compare-med | med {missing-as-worst | non-deterministic | confed } | compare-routerid| compare-neighborid | cost-community ignore | as-path { multipath-relax | ignore } | igp-metric ignore }
Syntax Description
(Optional) Negate a command or set its defaultsno
Change default bestpath selection algorithmbestpath
Compare MED on paths from different ASalways-compare-med
MEDmed
Treat missing MED as highest MEDmissing-as-worst
Not always pick the best-MED path among paths from same ASnon-deterministic
Compare router-id for identical EBGP pathscompare-routerid
When more paths available than max path config, use neighboridtibreaker
compare-neighborid
cost communitycost-community
Ignore cost communities in bestpath selectionignore
Compare MED only from paths originated from within a confederationconfed
AS-Pathas-path
Relax AS-Path restriction when choosing multipathsmultipath-relax
Ignore AS-Path during bestpath selectionignore
IGP metric for next-hopigp-metric
Ignore IGP metric for next-hop during bestpath selectionignore
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)228
B Commandsbestpath
Page 373
bfd-app session auto-expiry timeoutbfd-app session auto-expiry { timeout <millis> | now }
Syntax Description
BFD application commandsbfd-app
auto expiry start/endauto-expiry
session operationsession
timeout aftertimeout
expiry reached, dont wait to timeout, do them nownow
milli-secs latermillis
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)229
B Commandsbfd-app session auto-expiry timeout
Page 374
bfd-app session removebfd-app session remove { all | intf <intf_id> | iod <iod_id> }
Syntax Description
BFD application commandsbfd-app
session operationsession
Remove sessionsremove
Remove all sessionsall
Remove all sessions on interfaceintf
Interface Idintf_id
interface iodiod
Interface iod in hexiod_id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)230
B Commandsbfd-app session remove
Page 375
bfd-app session src-ip dest intf[no] bfd-app session src-ip { <src_ip> dest-ip <dest_ip> | <src_ipv6> dest-ip <dest_ipv6> } { intf <intf_id>| iod <iod_id> }
Syntax Description
(Optional) Negate a command or set its defaultsno
BFD application commandsbfd-app
session operationsession
Source ipsrc-ip
Source ip valuesrc_ip
Destination ipdest-ip
Destination ip valuedest_ip
interface iodiod
Interface iod in hexiod_id
interfaceintf
Interface Idintf_id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)231
B Commandsbfd-app session src-ip dest intf
Page 376
bfd[no] bfd [ ipv4 | ipv6 ]
Syntax Description
(Optional) Negate a command or set its defaultsno
BFD commandsbfd
(Optional) ipv4 sessionsipv4
(Optional) ipv6 sessionsipv6
Command Mode
• /exec/configure/if-ma /exec/configure/if-vlan /exec/configure/if-ma-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)232
B Commandsbfd
Page 377
bfd[ no | default ] bfd
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Bidirectional Fast Detection for the neighborbfd
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)233
B Commandsbfd
Page 378
bfd[no] bfd
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable IPv4 BFD on all ISIS interfacesbfd
Command Mode
• /exec/configure/router-isis/router-isis-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)234
B Commandsbfd
Page 379
bfd[no] bfd
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable IPv4 BFD on all ISIS interfacesbfd
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)235
B Commandsbfd
Page 380
bfd[no] bfd
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable BFD on all OSPF interfacesbfd
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)236
B Commandsbfd
Page 381
bfd[no] bfd
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable BFD on all EIGRP interfacesbfd
Command Mode
• /exec/configure/router-eigrp /exec/configure/router-eigrp/router-eigrp-vrf/exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)237
B Commandsbfd
Page 382
bfd[no] bfd
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable BFD on all OSPF interfacesbfd
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)238
B Commandsbfd
Page 383
bfd authentication interopbfd authentication interop | no bfd authentication interop
Syntax Description
Negate a command or set its defaultsno
BFD commandsbfd
Configure BFD authentication parametersauthentication
Allows keys to be sent in network format to interop with non N3k/N9Kswitches
interop
Command Mode
• /exec/configure/if-ma /exec/configure/if-vlan /exec/configure/if-ma-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)239
B Commandsbfd authentication interop
Page 384
bfd authentication key-id keybfd [ { ipv4 | ipv6 } ] authentication <auth_name> key-id <key_id_val> { key <key_val> | hex-key <h_key_val>} | no bfd [ { ipv4 | ipv6 } ] authentication
Syntax Description
Negate a command or set its defaultsno
BFD commandsbfd
Configure BFD authentication parametersauthentication
(Optional) ipv4 sessionsipv4
(Optional) ipv6 sessionsipv6
auth algorithmauth_name
Key ID to use in BFD frameskey-id
Key ID valuekey_id_val
ASCII SHA1 secretkey
HEX binary SHA1 secrethex-key
SHA1 secret valuekey_val
SHA1 secret value. e.g ABCD123h_key_val
Command Mode
• /exec/configure/if-ma /exec/configure/if-vlan /exec/configure/if-ma-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)240
B Commandsbfd authentication key-id key
Page 385
bfd echo-interface[no] bfd echo-interface <ifindex>
Syntax Description
(Optional) Negate a command or set its defaultsno
BFD commandsbfd
Configure interface used for bfd echo framesecho-interface
loopback interfaceifindex
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)241
B Commandsbfd echo-interface
Page 386
bfd echo-rx-intervalbfd [ ipv4 | ipv6 ] echo-rx-interval <intv> | no bfd [ ipv4 | ipv6 ] echo-rx-interval
Syntax Description
Negate a command or set its defaultsno
BFD commandsbfd
(Optional) ipv6 sessionsipv6
(Optional) ipv4 sessionsipv4
Configure BFD session echo rx intervalecho-rx-interval
Echo Rx Interval in millisecondsintv
Command Mode
• /exec/configure /exec/configure/if-ma /exec/configure/if-ma-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)242
B Commandsbfd echo-rx-interval
Page 387
bfd echo[no] bfd [ { ipv4 | ipv6 } ] echo
Syntax Description
(Optional) Negate a command or set its defaultsno
BFD commandsbfd
Configure Echo function for all address familiesecho
(Optional) ipv4 sessionsipv4
(Optional) ipv6 sessionsipv6
Command Mode
• /exec/configure/if-ma /exec/configure/if-vlan /exec/configure/if-ma-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)243
B Commandsbfd echo
Page 388
bfd interval[no] bfd [ ipv4 | ipv6 ] interval [ <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult> ]
Syntax Description
Negate a command or set its defaultsno
BFD commandsbfd
Configure BFD session interval parametersinterval
(Optional) ipv6 sessionsipv6
(Optional) ipv4 sessionsipv4
(Optional) TX interval in millisecondsmin_tx_mills
(Optional) Minimum RX intervalmin_rx
(Optional) RX interval in millisecondsmin_rx_mills
(Optional) Configure detect multiplier for bfd sessionsmultiplier
(Optional) Detect Multiplierint_mult
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)244
B Commandsbfd interval
Page 389
bfd interval[no] bfd [ ipv4 | ipv6 ] interval [ <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult> ]
Syntax Description
Negate a command or set its defaultsno
BFD commandsbfd
Configure BFD session interval parametersinterval
(Optional) ipv6 sessionsipv6
(Optional) ipv4 sessionsipv4
(Optional) TX interval in millisecondsmin_tx_mills
(Optional) Minimum RX intervalmin_rx
(Optional) RX interval in millisecondsmin_rx_mills
(Optional) Configure detect multiplier for bfd sessionsmultiplier
(Optional) Detect Multiplierint_mult
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel/exec/configure/if-ma /exec/configure/if-vlan /exec/configure/if-ma-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)245
B Commandsbfd interval
Page 390
bfd interval min_rx multiplierbfd [ ipv6 | ipv4 ] interval <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult>
Syntax Description
BFD commandsbfd
Configure BFD session interval parametersinterval
(Optional) ipv6 sessionsipv6
(Optional) ipv4 sessionsipv4
TX interval in millisecondsmin_tx_mills
Minimum RX intervalmin_rx
RX interval in millisecondsmin_rx_mills
Configure detect multiplier for bfd sessionsmultiplier
Detect Multiplierint_mult
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel/exec/configure/if-ma /exec/configure/if-vlan /exec/configure/if-ma-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)246
B Commandsbfd interval min_rx multiplier
Page 391
bfd interval min_rx multiplierbfd [ ipv6 | ipv4 ] interval <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult>
Syntax Description
BFD commandsbfd
Configure BFD session interval parametersinterval
(Optional) ipv6 sessionsipv6
(Optional) ipv4 sessionsipv4
TX interval in millisecondsmin_tx_mills
Minimum RX intervalmin_rx
RX interval in millisecondsmin_rx_mills
Configure detect multiplier for bfd sessionsmultiplier
Detect Multiplierint_mult
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)247
B Commandsbfd interval min_rx multiplier
Page 392
bfd move-session targetbfd move-session target <target_mod> [ <discr> ]
Syntax Description
BFD commandsbfd
move a sessionmove-session
Target moduletarget
Module numbertarget_mod
(Optional) Session discriminatordiscr
Command Mode
• /exec/configure/if-ma /exec/configure/if-ma-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)248
B Commandsbfd move-session target
Page 393
bfd multihop authentication key-id key bfd multihopauthentication
bfd multihop authentication <auth_name> key-id <key_id_val> { key <key_val> | hex-key <h_key_val> } |[ no | default ] bfd multihop authentication [ <auth_name> key-id <key_id_val> { key <key_val> | hex-key<h_key_val> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Bidirectional Fast Detection for the neighborbfd
For Multihop sessionsmultihop
Configure BFD authentication parametersauthentication
auth algorithmauth_name
Key ID to use in BFD frameskey-id
Key ID valuekey_id_val
ASCII SHA1 secretkey
HEX binary SHA1 secrethex-key
SHA1 secret valuekey_val
SHA1 secret value. e.g ABCD123h_key_val
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)249
B Commandsbfd multihop authentication key-id key bfd multihop authentication
Page 394
bfd multihop hosting-linecard add module[no] bfd multihop hosting-linecard add module <module_num>
Syntax Description
Negate a command or set its defaultsno
BFD commandsbfd
Configure BFD Multihop session interval parametersmultihop
Add the linecard to hosting-linecard for multihop sessionshosting-linecard
Add the linecard to hosting-linecard list for multihop sessionsadd
Linecard or module numbermodule
Module numbermodule_num
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)250
B Commandsbfd multihop hosting-linecard add module
Page 395
bfd multihop hosting-linecard add modulebfd multihop hosting-linecard add module <module_num>
Syntax Description
BFD commandsbfd
Configure BFD Multihop session interval parametersmultihop
Add the linecard to hosting-linecard for multihop sessionshosting-linecard
Add the linecard to hosting-linecard list for multihop sessionsadd
Linecard or module numbermodule
Module numbermodule_num
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)251
B Commandsbfd multihop hosting-linecard add module
Page 396
bfd multihop interval[no] bfd multihop interval [ <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult> ]
Syntax Description
Negate a command or set its defaultsno
BFD commandsbfd
Configure BFD Multihop session interval parametersmultihop
Configure BFD multihop session interval parametersinterval
(Optional) TX interval in millisecondsmin_tx_mills
(Optional) Minimum RX intervalmin_rx
(Optional) RX interval in millisecondsmin_rx_mills
(Optional) Configure detect multiplier for bfd multihop sessionsmultiplier
(Optional) Detect Multiplierint_mult
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)252
B Commandsbfd multihop interval
Page 397
bfd multihop interval min_rx multiplierbfd multihop interval <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult>
Syntax Description
BFD commandsbfd
Configure BFD Multihop session interval parametersmultihop
Configure BFD multihop session interval parametersinterval
TX interval in millisecondsmin_tx_mills
Minimum RX intervalmin_rx
RX interval in millisecondsmin_rx_mills
Configure detect multiplier for bfd multihop sessionsmultiplier
Detect Multiplierint_mult
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)253
B Commandsbfd multihop interval min_rx multiplier
Page 398
bfd multihop interval min_rx multiplierbfd multihop interval <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult> | { no | default } bfdmultihop interval [ <min_tx_mills> min_rx <min_rx_mills> multiplier <int_mult> ]
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Bidirectional Fast Detection for the neighborbfd
For Multihop sessionsmultihop
Configure BFD session interval parametersinterval
TX interval in millisecondsmin_tx_mills
Minimum RX intervalmin_rx
RX interval in millisecondsmin_rx_mills
Configure detect multiplier for bfd sessionsmultiplier
Detect Multiplierint_mult
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)254
B Commandsbfd multihop interval min_rx multiplier
Page 399
bfd neighbor src-ip dest[no] bfd neighbor src-ip { <src_ip> dest-ip <dest_ip> | <src_ipv6> dest-ip <dest_ipv6> }
Syntax Description
(Optional) Negate a command or set its defaultsno
BFD commandsbfd
BFD neighbor configuration commands (simulate client)neighbor
Source ipsrc-ip
Source ip valuesrc_ip
Destination ipdest-ip
Destination ip valuedest_ip
Command Mode
• /exec/configure/if-ma /exec/configure/if-ma-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)255
B Commandsbfd neighbor src-ip dest
Page 400
bfd optimize subinterface[no] bfd [ ipv4 ] optimize subinterface
Syntax Description
(Optional) Negate a command or set its defaultsno
BFD commandsbfd
optimizeoptimize
optimize subinterfacessubinterface
(Optional) ipv4 sessionsipv4
Command Mode
• /exec/configure/if-ma /exec/configure/if-ma-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)256
B Commandsbfd optimize subinterface
Page 401
bfd per-link[no] bfd [ { ipv4 | ipv6 } ] per-link
Syntax Description
(Optional) Negate a command or set its defaultsno
BFD commandsbfd
Run BFD sessions on each port-channel linkper-link
(Optional) ipv4 sessionsipv4
(Optional) ipv6 sessionsipv6
Command Mode
• /exec/configure/if-eth-port-channel /exec/configure/if-port-channel-sub/exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)257
B Commandsbfd per-link
Page 402
bfd session-store remove clientbfd session-store remove <hex_disc> client <int_cl>
Syntax Description
BFD commandsbfd
session store operationsession-store
Remove session from session storeremove
Session discriminatorhex_disc
Client Idclient
clientint_cl
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)258
B Commandsbfd session-store remove client
Page 403
bfd session-store source-ip dest-ip intf clientbfd session-store source-ip <src_ip> dest-ip <dest_ip> intf <intf_id> client <int_cl>
Syntax Description
BFD commandsbfd
Session store operationsession-store
source ipsource-ip
source ip valuesrc_ip
dest ipdest-ip
source ip valuedest_ip
interfaceintf
Interface Idintf_id
Client Idclient
clientint_cl
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)259
B Commandsbfd session-store source-ip dest-ip intf client
Page 404
bfd session state statebfd session state <hex_disc> state <state_up_down>
Syntax Description
BFD commandsbfd
session related testsession
Change session statestate
Session discriminatorhex_disc
Change to statestate
UP/DOWNstate_up_down
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)260
B Commandsbfd session state state
Page 405
bfd slow-timerbfd [ { ipv4 | ipv6 } ] slow-timer <int_slow_timer> | no bfd [ { ipv4 | ipv6 } ] slow-timer
Syntax Description
Negate a command or set its defaultsno
BFD commandsbfd
Configure slow mode timer for sessionsslow-timer
Slow rate timer in millisecondsint_slow_timer
(Optional) ipv4 sessionsipv4
(Optional) ipv6 sessionsipv6
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)261
B Commandsbfd slow-timer
Page 406
bfd startup-timer bfd startup-timerbfd startup-timer <int_startup_timer> | [ no ] bfd startup-timer
Syntax Description
(Optional) Negate a command or set its defaultsno
BFD commandsbfd
Configure Delayed Start Up timer for sessionsstartup-timer
Start Up timer in secondsint_startup_timer
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)262
B Commandsbfd startup-timer bfd startup-timer
Page 407
bfshellbfshell
Syntax Description
bfshellbfshell
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)263
B Commandsbfshell
Page 408
bfshell cmdbfshell cmd <cmd>
Syntax Description
bfshellbfshell
Specify commandcmd
Quoted commands to be execcmd
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)264
B Commandsbfshell cmd
Page 409
bfshell modulebfshell module <module>
Syntax Description
bfshellbfshell
Select modulemodule
Module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)265
B Commandsbfshell module
Page 410
bfshell module cmdbfshell module <module> cmd <cmd>
Syntax Description
bfshellbfshell
Select modulemodule
Specify commandcmd
Module numbermodule
Quoted commands to be execcmd
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)266
B Commandsbfshell module cmd
Page 411
binary-location[no] binary-location <source-uri>
Syntax Description
(Optional) Negate a command or set its defaultsno
the location binaries are downloaded frombinary-location
Location for restoration to pick up binariessource-uri
Command Mode
• /exec/configure/personality
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)267
B Commandsbinary-location
Page 412
bind interface[no] bind interface <interface-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Bind the VFCbind
Bind the VFC to an interfaceinterface
Interface nameinterface-name
Command Mode
• /exec/configure/if-vfc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)268
B Commandsbind interface
Page 413
bind mac-address[no] bind mac-address <mac0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Bind the VFCbind
Bind the VFC to a MAC Addressmac-address
Enter MAC addrress in dotted hex formatmac0
Command Mode
• /exec/configure/if-vfc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)269
B Commandsbind mac-address
Page 414
blink[no] blink { module <module> | <s0> <santa-cruz-range> | chassis | powersupply <psnum> | fan <fan_num>}
Syntax Description
(Optional) Negate a command or set its defaultsno
blink locator ledblink
blink module ledmodule
please enter the module numbermodule
blink a specific xbars0
please enter the xbar numbersanta-cruz-range
blink chassis ledchassis
blink powersupply ledpowersupply
powersupply numberpsnum
blink Fan ledfan
fan numberfan_num
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)270
B Commandsblink
Page 415
bloggerd live-process-core sapbloggerd live-process-core sap <sap>
Syntax Description
Blogger commandsbloggerd
Dump the core of the live-processlive-process-core
Dump core for a particular SAPsap
Enter a valid SAP. Enter 0 for ALL SAPs in this VDCsap
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)271
B Commandsbloggerd live-process-core sap
Page 416
bloggerd log-dump all[no] bloggerd log-dump { all | [ module <module> ] sap <sap_num> [ vdc <new_id> | vdc-all ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Blogger commandsbloggerd
Dump Log Bufferlog-dump
Log Dump for ALL services across ALL modules in the switch onreaching threshold
all
(Optional) Enable Buffer Dump for particular Modulemodule
(Optional) Enter a valid Module Numbermodule
Enable Buffer Dump for a particular sapsap
Enter a valid SAP. Enter 0 for ALL SAPs in this VDCsap_num
(Optional) Enable Log Dump for a particular VDC. DEFAULT_VDCby default
vdc
(Optional) Enter a valid VDC IDnew_id
(Optional) Enable Log Dump for the sap on ALL VDCsvdc-all
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)272
B Commandsbloggerd log-dump all
Page 417
bloggerd log-dump once log-buffer sap event-historybloggerd log-dump once log-buffer sap <sap> event-history { errors | msgs | { app-specific <uuid> instance<buffer-instance> } }
Syntax Description
Blogger commandsbloggerd
Dump Log Bufferlog-dump
Dump Log Buffer once immediatelyonce
Dump Log bufferlog-buffer
Enable Buffer Dump for a particular sapsap
Enter a valid SAP. Enter 0 for ALL SAPs in this VDCsap
Event-History Buffersevent-history
event-history errorserrors
event-history messagesmsgs
application specific event historyapp-specific
Enter valid app's UUIDuuid
Buffer Instance of the App-Specific SDWrap bufferinstance
Enter a valid SDWrap buffer instance for the appbuffer-instance
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)273
B Commandsbloggerd log-dump once log-buffer sap event-history
Page 418
bloggerd log-dump once pss uuidbloggerd log-dump once pss uuid <uuid>
Syntax Description
Blogger commandsbloggerd
Dump Log Bufferlog-dump
Dump Log Buffer once immediatelyonce
Dump PSSpss
Dump PSS for a particular UUIDuuid
Enter a app's UUIDuuid
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)274
B Commandsbloggerd log-dump once pss uuid
Page 419
bloggerd log-throttle[no] bloggerd log-throttle [ min-rollover <min-rollover>max-rollover-per-minute <max-rollover-per-minute>]
Syntax Description
(Optional) Negate a command or set its defaultsno
Blogger commandsbloggerd
Enable Log Dump Throttling for all NxOS serviceslog-throttle
(Optional) Number of minimum buffer rollovers before starting tothrottle. Default: 5
min-rollover
(Optional) Enter the mininum number of roll-overs before throttleinglog-dump. Default: 5
min-rollover
(Optional) Maximum allowed buffer rollovers per minute. Default: 1max-rollover-per-minute
(Optional) Enter the maximum allowed roll-overs per minute beforethrottling. Default: 1
max-rollover-per-minute
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)275
B Commandsbloggerd log-throttle
Page 420
bloggerd log-transferbloggerd log-transfer { <ip-addr> <path> | logflash }
Syntax Description
Blogger commandsbloggerd
Configure log transferlog-transfer
IP addr of logging serverip-addr
Path in tftp server to store logs. Eg: logOutputpath
Move all log-files to logflashlogflash
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)276
B Commandsbloggerd log-transfer
Page 421
bloggerd log-transfer[no] bloggerd log-transfer
Syntax Description
Negate a command or set its defaultsno
Blogger commandsbloggerd
Configure log transferlog-transfer
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)277
B Commandsbloggerd log-transfer
Page 422
bloggerd parse log-buffer filebloggerd parse log-buffer { file | directory } <uri0> [ dsf_table <uri1> ]
Syntax Description
Blogger commandsbloggerd
Parse a fileparse
Parse buffer log filelog-buffer
Enter path of directorydirectory
Enter file name. Please unzip file before parsing!file
Linux path to file/directory (Eg: /bootflash/abc)uri0
(Optional) Enter dsf table file name.dsf_table
(Optional) Linux path to file/directory (Eg: /bootflash/abc)uri1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)278
B Commandsbloggerd parse log-buffer file
Page 423
bloggerd parse log-buffer file sapbloggerd parse log-buffer file <uri0> sap <sap-num>
Syntax Description
Blogger commandsbloggerd
Parse a fileparse
Parse buffer log filelog-buffer
Enter file name. Please unzip file before parsing!file
Linux path to file (Eg: /bootflash/abc)uri0
SAP of the application which should parse the filesap
Enter a valid SAP. Enter 0 for ALL SAPs in this VDCsap-num
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)279
B Commandsbloggerd parse log-buffer file sap
Page 424
bloggerd parse pss filebloggerd parse pss file <uri0>
Syntax Description
Blogger commandsbloggerd
Parse a fileparse
Parse a dumped PSS Filepss
Enter file name (without pss extensions). Please unzip file before parsing!file
Linux path to file/directory (Eg: /bootflash/abc)uri0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)280
B Commandsbloggerd parse pss file
Page 425
bmp-activate-serverbmp-activate-server <server-number> | { no | default } bmp-activate-server <server-number>
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Activate BMP monitoring for the peerbmp-activate-server
Server Idserver-number
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)281
B Commandsbmp-activate-server
Page 426
bmp-server[no] bmp-server <server-number>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure bmp-serverbmp-server
server number valueserver-number
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)282
B Commandsbmp-server
Page 427
boot-install nxos{ boot-install nxos <uri0> | no boot-install nxos [ <uri0> ] }
Syntax Description
Negate a command or set its defaultsno
Configure boot variablesboot-install
Configure NXOS imagenxos
Enter NXOS image uriuri0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)283
B Commandsboot-install nxos
Page 428
boot-orderboot-order <new_id>
Syntax Description
The order at which a vdc will boot up. VDCs at the same level will bestarted parallely
boot-order
The order at which a vdc will boot up. VDCs at the same level will bestarted parallely
new_id
Command Mode
• /exec/configure/vdc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)284
B Commandsboot-order
Page 429
boot{ boot <s0> <uri0> [ module [ <module> ] ] | no boot <s0> [ <uri0> [ module [ <module> ] ] ] }
Syntax Description
Negate a command or set its defaultsno
Configure boot variablesboot
use [show boot variables] for list of keywordss0
Enter module image uriuri0
(Optional) Enter module number for the imagemodule
(Optional) Enter module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)285
B Commandsboot
Page 430
boot aci{ boot aci <uri0> | no boot aci [ <uri0> ] }
Syntax Description
Negate a command or set its defaultsno
Configure boot variablesboot
Configure ACI imageaci
Enter ACI image uriuri0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)286
B Commandsboot aci
Page 431
boot auto-copy[no] boot auto-copy
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure boot variablesboot
Turns on/off autocopy of bootvar imagesauto-copy
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)287
B Commandsboot auto-copy
Page 432
boot kickstart{ boot kickstart <uri0> | no boot kickstart [ <uri0> ] }
Syntax Description
Negate a command or set its defaultsno
Configure boot variablesboot
Configure kickstart imagekickstart
Enter Kickstart image uriuri0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)288
B Commandsboot kickstart
Page 433
boot mode docker_cluster[no] boot mode docker_cluster [ dhcp <option> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure boot modeboot
boot modemode
Turns on/off docker_cluster modedocker_cluster
(Optional) Custom DHCP optiondhcp
(Optional) Opiton, default is 250option
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)289
B Commandsboot mode docker_cluster
Page 434
boot mode docker_standalone[no] boot mode docker_standalone
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure boot modeboot
boot modemode
Turns on/off docker_standalone mode (for internal use only)docker_standalone
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)290
B Commandsboot mode docker_standalone
Page 435
boot mode lxc[no] boot mode lxc
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure boot modeboot
boot modemode
Turns on/off lxc modelxc
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)291
B Commandsboot mode lxc
Page 436
boot nxos{ boot nxos <uri0> | no boot nxos [ <uri0> ] }
Syntax Description
Negate a command or set its defaultsno
Configure boot variablesboot
Configure NXOS imagenxos
Enter nxos image uriuri0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)292
B Commandsboot nxos
Page 437
boot nxos sup-1{ boot nxos <uri0> sup-1 | no boot nxos <uri0> sup-1 }
Syntax Description
Negate a command or set its defaultsno
Configure boot variablesboot
Configure NXOS imagenxos
Enter kickstart image uriuri0
Enter sup-1 to configure the 1st supsup-1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)293
B Commandsboot nxos sup-1
Page 438
boot nxos sup-1 sup-2{ boot nxos <uri0> sup-1 sup-2 | no boot nxos <uri0> sup-1 sup-2 }
Syntax Description
Negate a command or set its defaultsno
Configure boot variablesboot
Configure NXOS imagenxos
Enter kickstart image uriuri0
Enter sup-1 to configure the 1st supsup-1
Enter sup-2 to configure the 2nd supsup-2
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)294
B Commandsboot nxos sup-1 sup-2
Page 439
boot nxos sup-2{ boot nxos <uri0> sup-2 | no boot nxos <uri0> sup-2 }
Syntax Description
Negate a command or set its defaultsno
Configure boot variablesboot
Configure NXOS imagenxos
Enter kickstart image uriuri0
Enter sup-2 to configure the 2nd supsup-2
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)295
B Commandsboot nxos sup-2
Page 440
boot order bootflash{ boot order bootflash [ pxe ] | no boot order bootflash [ pxe ] }
Syntax Description
Negate a command or set its defaultsno
Configure boot variablesboot
Configure loader fallback orderorder
Boot from Bootflashbootflash
(Optional) Pxe Bootpxe
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)296
B Commandsboot order bootflash
Page 441
boot order pxe{ boot order pxe [ bootflash ] | no boot order pxe [ bootflash ] }
Syntax Description
Negate a command or set its defaultsno
Configure boot variablesboot
Configure loader fallback orderorder
Pxe Bootpxe
(Optional) Boot from Bootflashbootflash
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)297
B Commandsboot order pxe
Page 442
boot poap enable{ boot poap enable | no boot poap enable }
Syntax Description
Negate a command or set its defaultsno
Configure boot variablesboot
feature poappoap
Enable Perpetual POAP making POAP kick in on reload even withstartup-config
enable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)298
B Commandsboot poap enable
Page 443
boot system{ boot system <uri0> | no boot system [ <uri0> ] }
Syntax Description
Negate a command or set its defaultsno
Configure boot variablesboot
Configure system imagesystem
Enter system image uriuri0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)299
B Commandsboot system
Page 444
bootmode boot[no] bootmode boot
Syntax Description
(Optional) Negate a command or set its defaultsno
set bootmode for all modules in the switchbootmode
boot in boot modeboot
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)300
B Commandsbootmode boot
Page 445
bootmode extruntime[no] bootmode extruntime
Syntax Description
(Optional) Negate a command or set its defaultsno
set bootmode for all modules in the switchbootmode
boot in runtime mode with extended diagsextruntime
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)301
B Commandsbootmode extruntime
Page 446
bootmode hitless[no] bootmode hitless
Syntax Description
(Optional) Negate a command or set its defaultsno
set bootmode for all modules in the switchbootmode
boot in hitless modehitless
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)302
B Commandsbootmode hitless
Page 447
bootmode module[no] bootmode module <module> { boot | extruntime | hitless | netboot | nodiagruntime | runtime }
Syntax Description
(Optional) Negate a command or set its defaultsno
set bootmode for all modules in the switchbootmode
set bootmode for a given module in the switchmodule
please enter module numbermodule
boot in boot modeboot
boot in runtime mode with extended diagsextruntime
boot in hitless modehitless
boot using boot netboot in runtime modenetboot
boot in runtime mode without running any diagsnodiagruntime
boot in runtime mode with normal diagsruntime
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)303
B Commandsbootmode module
Page 448
bootmode nodiagruntime[no] bootmode nodiagruntime
Syntax Description
(Optional) Negate a command or set its defaultsno
set bootmode for all modules in the switchbootmode
boot in runtime mode without running any diagsnodiagruntime
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)304
B Commandsbootmode nodiagruntime
Page 449
bootmode runtime[no] bootmode runtime
Syntax Description
(Optional) Negate a command or set its defaultsno
set bootmode for all modules in the switchbootmode
boot in runtime mode with normal diagsruntime
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)305
B Commandsbootmode runtime
Page 450
buffer-boost[no] buffer-boost
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable extra buffers for this interfacebuffer-boost
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)306
B Commandsbuffer-boost
Page 451
buffer-deletebuffer-delete { <id-range> | <id> | all }
Syntax Description
delete buffered command(s)buffer-delete
Range(whole-number) of command id(s) to be deleted fromswitch-profile buffer
id-range
Exact command id (x.x.x format) to be deleted from switch-profile bufferid
delete all buffered commandsall
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)307
B Commandsbuffer-delete
Page 452
buffer-movebuffer-move <fromid> <toid>
Syntax Description
move buffered command(s)buffer-move
Command id of command(s) to be moved in switch-profile bufferfromid
New command id to be assigned in switch-profile buffertoid
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)308
B Commandsbuffer-move
Page 453
burst-detect enable[no] burst-detect enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Specify OOBST burst-detect thresholds for the classburst-detect
enableenable
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)309
B Commandsburst-detect enable
Page 454
burst-detect rise-threshold bytes fall-threshold bytes2[no] burst-detect rise-threshold <value-in-bytes> bytes fall-threshold <value-in-bytes> bytes2
Syntax Description
(Optional) Negate a command or set its defaultsno
Specify OOBST burst-detect thresholds for the classburst-detect
Threshold bytes(queue depth) to start monitoring burstrise-threshold
value-in-bytes
bytesbytes
Threshold bytes(queue depth) to stop monitoring burstfall-threshold
value-in-bytes
bytes2bytes2
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)310
B Commandsburst-detect rise-threshold bytes fall-threshold bytes2
Page 455
C Commands
• cabundle url, on page 323• callhome, on page 324• callhome send configuration, on page 325• callhome send diagnostic, on page 326• callhome test, on page 327• callhome test inventory, on page 328• capability additional-paths receive, on page 329• capability additional-paths send, on page 330• capability suppress 4-byte-as, on page 331• capability vrf-lite, on page 332• capture, on page 333• capture, on page 334• capture session, on page 335• carrier-delay, on page 336• catena, on page 337• catena device-group, on page 338• catena port-acl, on page 339• catena port-group, on page 340• catena vlan-group, on page 341• cbts-member tunnel-te, on page 342• cd, on page 343• cdp advertise v1, on page 344• cdp enable, on page 345• cdp enable, on page 346• cdp format device-id, on page 347• cdp holdtime, on page 348• cdp timer, on page 349• certificate, on page 350• cfs debug all, on page 351• cfs distribute, on page 352• cfs eth cos, on page 353• cfs eth distribute, on page 354• cfs ipv4 distribute, on page 355
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)311
Page 456
• cfs ipv6 distribute, on page 356• cfs region, on page 357• chain, on page 358• change-password, on page 359• channel-group, on page 360• channel-group, on page 361• channel-group, on page 362• channel-group, on page 363• channel-group force, on page 364• channel-group force, on page 365• channel mode, on page 366• channel mode active, on page 367• chassis-family fretta, on page 368• checkpoint, on page 369• checkpoint, on page 370• cipher-suite, on page 371• class-map, on page 372• class-map type control-plane, on page 373• class-map type network-qos, on page 374• class-map type psp, on page 375• class-map type queuing, on page 376• class-map type queuing, on page 377• class, on page 378• class, on page 379• class __inline__, on page 380• class class-default, on page 381• class type network-qos, on page 382• class type network-qos class-default, on page 383• class type psp, on page 384• class type queuing, on page 385• clear, on page 386• clear, on page 387• clear, on page 388• clear, on page 389• clear aaa local user blocked username, on page 390• clear access-list counters, on page 391• clear access-list hardware counters, on page 392• clear access-list ipsg stats, on page 393• clear accounting log, on page 394• clear aclqos cl-qos, on page 395• clear aclqos fab, on page 396• clear aclqos fc, on page 397• clear aclqos libdrv, on page 398• clear aclqos map, on page 399• clear aclqos merge, on page 400• clear aclqos pl, on page 401
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)312
C Commands
Page 457
• clear aclqos ppf-parse, on page 402• clear aclqos ppf, on page 403• clear aclqos qng-hw, on page 404• clear aclqos qng, on page 405• clear aclqos rl, on page 406• clear aclqos rm, on page 407• clear aclqos sch, on page 408• clear aclqos stats, on page 409• clear aclqos tbl, on page 410• clear aclqos trace-detail, on page 411• clear aclqos trace, on page 412• clear aclqos uf, on page 413• clear bfd statistics, on page 414• clear bgp, on page 415• clear bgp bmp stats server, on page 417• clear bgp event-history, on page 418• clear bgp private, on page 419• clear bootvar log, on page 421• clear cdp counters, on page 422• clear checkpoint database, on page 423• clear cli history, on page 424• clear controller accounting log, on page 425• clear copp statistics, on page 426• clear cores, on page 427• clear cores archive, on page 428• clear counters, on page 429• clear counters buffers, on page 430• clear counters interface, on page 431• clear counters interface, on page 432• clear counters interface, on page 433• clear counters interface all, on page 434• clear counters interface snmp, on page 435• clear counters tah-buffers, on page 436• clear crypto ca trustpool timer, on page 437• clear debug-logfile, on page 438• clear debug logfile, on page 439• clear dot1x all, on page 440• clear dot1x stats interface, on page 441• clear ecp statistics, on page 442• clear eigrp event-history, on page 443• clear evb hosts, on page 444• clear evb hosts, on page 445• clear evb statistics, on page 446• clear fabric database dci vrf node-id, on page 447• clear fabric database host all vni, on page 448• clear fabric database host statistics, on page 449
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)313
C Commands
Page 458
• clear fabric database include-vrf, on page 450• clear fabric database statistics, on page 451• clear fabric database statistics type server-proto radius group, on page 452• clear fabric database statistics type server-proto xmpp ip, on page 453• clear fabric multicast event-history, on page 454• clear fc2, on page 455• clear fctimer session, on page 456• clear flow cache, on page 457• clear flow cache, on page 458• clear flow exporter, on page 459• clear forwarding adjacency module, on page 460• clear forwarding cumulative counter, on page 461• clear forwarding distribution lisp counters all, on page 462• clear forwarding events-history, on page 463• clear forwarding inconsistency, on page 464• clear forwarding ipv4 multicast counters, on page 465• clear forwarding ipv6-l3-route-history, on page 466• clear forwarding ipv6 adjacency module, on page 467• clear forwarding ipv6 inconsistency, on page 468• clear forwarding ipv6 multicast counters, on page 469• clear forwarding ipv6 route module, on page 470• clear forwarding l2-mc-route-history, on page 471• clear forwarding l2-oiflist-history, on page 472• clear forwarding l2-route-history, on page 473• clear forwarding l2mcast info l2-mc-route-history, on page 474• clear forwarding l2mcast info l2-oiflist-history, on page 475• clear forwarding l2mcast info l2-route-history, on page 476• clear forwarding l2mcast info l2-xbar-history, on page 477• clear forwarding l2mcast info statistics, on page 478• clear forwarding l2vpn trace member-history, on page 479• clear forwarding l3-route-history, on page 480• clear forwarding oiflist-history, on page 481• clear forwarding route module, on page 482• clear forwarding trace ecmp-history, on page 483• clear forwarding trace mfib oif-history, on page 484• clear forwarding trace mfib oiflist-history, on page 485• clear forwarding trace mfib platform oiflist-history, on page 486• clear forwarding trace mfib v4-route-history, on page 487• clear forwarding trace mfib v6-route-history, on page 488• clear forwarding trace v4-adj-history, on page 489• clear forwarding trace v4-pfx-history, on page 490• clear forwarding trace v4-rnh-history, on page 491• clear forwarding trace v6-adj-history, on page 492• clear forwarding trace v6-pfx-history, on page 493• clear forwarding trace v6-rnh-history, on page 494• clear forwarding trace vobj-history, on page 495
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)314
C Commands
Page 459
• clear frame traffic, on page 496• clear fs-daemon log, on page 497• clear hardware flow ip, on page 498• clear hardware flow ipv6, on page 499• clear hardware flow l2, on page 500• clear hardware ip verify, on page 501• clear hardware profile buffer monitor, on page 503• clear hardware profile latency monitor, on page 504• clear hardware profile packet-drop file_instance, on page 505• clear hardware rate-limiter, on page 506• clear hardware rate-limiter, on page 507• clear hsrp counters clear hsrp state-history, on page 508• clear install all failed-standby, on page 509• clear install failure-reason, on page 510• clear install log-history all, on page 511• clear install status, on page 512• clear ip, on page 513• clear ip adjacency statistics, on page 514• clear ip amt tunnel, on page 515• clear ip arp, on page 516• clear ip arp controller-statistics, on page 517• clear ip arp inspection log, on page 518• clear ip arp inspection statistics vlan, on page 519• clear ip arp multihoming-statistics, on page 520• clear ip arp statistics, on page 521• clear ip arp suppression-cache statistics, on page 522• clear ip arp tunnel-statistics, on page 523• clear ip arp vpc-statistics, on page 524• clear ip dhcp global statistics, on page 525• clear ip dhcp relay statistics, on page 526• clear ip dhcp snooping binding, on page 527• clear ip dhcp snooping statistics, on page 528• clear ip eigrp accounting, on page 529• clear ip eigrp event-history, on page 530• clear ip eigrp event-history bfd, on page 531• clear ip eigrp redistribution, on page 532• clear ip eigrp route-map statistics redistribute, on page 533• clear ip eigrp traffic, on page 534• clear ip igmp event-history, on page 535• clear ip igmp groups, on page 536• clear ip igmp interface statistics, on page 537• clear ip igmp snooping event-history, on page 538• clear ip igmp snooping explicit-tracking, on page 539• clear ip igmp snooping groups, on page 540• clear ip igmp snooping proxy querier ports vlan, on page 541• clear ip igmp snooping report statistics, on page 542
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)315
C Commands
Page 460
• clear ip igmp snooping statistics, on page 543• clear ip interface statistics, on page 544• clear ip lisp data-cache, on page 545• clear ip lisp map-cache, on page 546• clear ip lisp statistics, on page 547• clear ip mbgp dampening, on page 548• clear ip mbgp flap-statistics, on page 550• clear ip mbgp peer-template, on page 552• clear ip mfwd event-history, on page 554• clear ip mroute, on page 555• clear ip mroute statistics, on page 556• clear ip msdp event-history, on page 557• clear ip msdp peer, on page 558• clear ip msdp policy statistics sa-policy in, on page 559• clear ip msdp sa, on page 560• clear ip msdp statistics, on page 561• clear ip nat-alias address, on page 562• clear ip nat statistics, on page 563• clear ip nat translation, on page 564• clear ip ospf database, on page 566• clear ip ospf event-history, on page 567• clear ip ospf interface, on page 568• clear ip ospf neighbor, on page 569• clear ip ospf policy statistics, on page 570• clear ip ospf redistribution, on page 572• clear ip ospf statistics, on page 573• clear ip ospf traffic, on page 574• clear ip pim event-history, on page 575• clear ip pim interface statistics, on page 576• clear ip pim policy statistics, on page 577• clear ip pim policy statistics jp, on page 578• clear ip pim route, on page 579• clear ip pim statistics, on page 580• clear ip rip policy statistics redistribute bgp, on page 581• clear ip rip statistics, on page 582• clear ip routing multicast event-history, on page 583• clear ip traffic, on page 584• clear ipv6 adjacency statistics, on page 585• clear ipv6 amt tunnel, on page 586• clear ipv6 dhcp-ldra statistics, on page 587• clear ipv6 dhcp relay statistics, on page 588• clear ipv6 eigrp route-map statistics redistribute, on page 589• clear ipv6 icmp, on page 590• clear ipv6 icmp vpc-statistics, on page 591• clear ipv6 interface statistics, on page 592• clear ipv6 lisp data-cache, on page 593
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)316
C Commands
Page 461
• clear ipv6 lisp statistics, on page 594• clear ipv6 mld groups, on page 595• clear ipv6 mroute, on page 596• clear ipv6 neighbor, on page 597• clear ipv6 neighbor binding, on page 598• clear ipv6 pim event-history, on page 599• clear ipv6 pim interface statistics, on page 600• clear ipv6 pim policy statistics jp, on page 601• clear ipv6 pim route, on page 602• clear ipv6 pim statistics, on page 603• clear ipv6 raguard statistics, on page 604• clear ipv6 rip policy statistics redistribute bgp, on page 605• clear ipv6 routing multicast event-history, on page 606• clear ipv6 snooping counters, on page 607• clear ipv6 snooping events, on page 608• clear ipv6 snooping messages, on page 609• clear ipv6 traffic, on page 610• clear isis adjacency, on page 611• clear isis dpi, on page 612• clear isis event-history, on page 613• clear isis ipv6 route-map statistics, on page 614• clear isis redistribution, on page 616• clear isis route-map statistics, on page 617• clear isis spf-log, on page 619• clear isis statistics, on page 620• clear isis traffic, on page 621• clear itd statistics, on page 622• clear keystore, on page 623• clear l2dbg, on page 624• clear l2fwder statistics, on page 625• clear l3vm event-history, on page 626• clear lacp counters, on page 627• clear ldap-server statistics, on page 628• clear license, on page 630• clear lim counters, on page 631• clear line, on page 632• clear lisp ddt referral-cache, on page 633• clear lisp dynamic-eid, on page 634• clear lisp proxy-itr, on page 635• clear lisp site, on page 636• clear lldp counters, on page 637• clear lldp counters interface, on page 638• clear logging ip access-list cache, on page 639• clear logging logfile, on page 640• clear logging nvram, on page 641• clear logging onboard, on page 642
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)317
C Commands
Page 462
• clear logging onboard, on page 643• clear logging session, on page 644• clear mac address-table datapath, on page 645• clear mac address-table dynamic, on page 646• clear mts message statistics, on page 647• clear mvr counters, on page 648• clear mvr counters receiver-ports, on page 649• clear mvr counters source-ports, on page 650• clear nbm flow statistics, on page 651• clear ngoam, on page 652• clear ngoam, on page 653• clear ngoam, on page 654• clear ngoam, on page 655• clear ngoam pathtrace, on page 656• clear ntp session, on page 657• clear ntp statistics, on page 658• clear nvram, on page 659• clear nxapi-server logs, on page 660• clear openflow switch controller all, on page 661• clear ospfv3 database, on page 662• clear ospfv3 event-history, on page 663• clear ospfv3 interface, on page 664• clear ospfv3 neighbor, on page 665• clear ospfv3 policy statistics, on page 666• clear ospfv3 statistics, on page 668• clear ospfv3 traffic, on page 669• clear peer-info interface vsan, on page 670• clear pktmgr client, on page 671• clear pktmgr interface, on page 672• clear plb analytics, on page 673• clear port-security dynamic address vlan, on page 674• clear port-security dynamic interface, on page 675• clear processes log all, on page 676• clear processes log all vdc-all, on page 677• clear processes log archive, on page 678• clear processes log pid, on page 679• clear processes vdc log all, on page 680• clear processes vdc log pid, on page 681• clear ptp corrections, on page 682• clear ptp counters interface, on page 683• clear qos policies, on page 684• clear qos policies force, on page 685• clear qos statistics, on page 686• clear queuing burst-detect, on page 687• clear queuing pfc-queue, on page 688• clear queuing pfc-queue interface, on page 689
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)318
C Commands
Page 463
• clear queuing tah-pfc-queue, on page 690• clear radius-server statistics, on page 691• clear radius session, on page 693• clear rmon, on page 694• clear route-map pbr-statistics, on page 695• clear routing event-history, on page 696• clear routing ip multicast mfdm pending counters, on page 697• clear routing ip multicast rpf-source retry-cache, on page 698• clear routing ipv6 event-history, on page 699• clear routing ipv6 multicast, on page 700• clear routing multicast, on page 701• clear scheduler logfile, on page 702• clear screen, on page 703• clear session state name, on page 704• clear sflow statistics, on page 705• clear snmp counters, on page 706• clear snmp hostconfig, on page 707• clear sockets statistics, on page 708• clear spanning-tree counters, on page 709• clear spanning-tree detected-protocols, on page 710• clear spanning-tree sps-hist, on page 711• clear ssh hosts, on page 712• clear statistics module-all, on page 713• clear statistics module, on page 714• clear sup-monitor drops session, on page 715• clear system login failures, on page 716• clear system reset-reason, on page 717• clear tacacs-server statistics, on page 718• clear tech-support lock, on page 720• clear tech-support lock, on page 721• clear user, on page 722• clear veobc counters, on page 723• clear vlan access-list counters, on page 724• clear vlan counters, on page 725• clear vmtracker counters, on page 726• clear vpc statistics all, on page 727• clear vpc statistics peer-keepalive, on page 728• clear vpc statistics vpc, on page 729• clear vpc transport statistics, on page 730• clear vrrp statistics, on page 731• clear vrrpv3 event-history, on page 732• clear vrrpv3 statistics, on page 733• clear vtp counters, on page 734• cli alias name, on page 735• cli create new-cmd, on page 736• cli var name, on page 737
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)319
C Commands
Page 464
• cli var name, on page 738• cli var name, on page 739• cli var name, on page 740• cli verifynrun, on page 741• client-to-client reflection, on page 742• clis all, on page 743• clock-tolerance ntp oneway absolute, on page 744• clock format 12, on page 745• clock format show-timezone debug, on page 746• clock format show-timezone syslog, on page 747• clock protocol, on page 748• clock set, on page 749• clock summer, on page 751• clock sync-interval, on page 752• cluster-id, on page 753• collect, on page 754• collect, on page 755• collect, on page 756• collect, on page 757• collect, on page 758• collect, on page 759• collect counter bytes, on page 760• collect ip version, on page 761• collect timestamp sys-uptime first, on page 762• collect transport tcp flags, on page 763• color, on page 764• commit, on page 765• commit, on page 766• commit, on page 767• commit verbose, on page 768• compress-bitfields ipv6 multicast, on page 769• compress-bitfields ipv6 multicast, on page 770• compress-bitfields multicast, on page 771• conf-offset, on page 772• confederation identifier, on page 773• confederation peers, on page 774• config-source controller, on page 775• configure, on page 776• configure config-template on substitute, on page 777• configure maintenance profile normal, on page 778• configure profile, on page 779• configure replace, on page 780• configure replace abort, on page 781• configure replace commit, on page 782• configure session, on page 783• configure sync, on page 784
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)320
C Commands
Page 465
• congestion-control dctcp ecn-threshold bytes, on page 785• congestion-control ecn, on page 786• congestion-control random-detect, on page 787• congestion-control random-detect forward-nonecn, on page 788• congestion-control random-detect global-buffer minimum-threshold maximum-threshold, on page 789• congestion-control tail-drop, on page 790• connect, on page 791• connected-prefix-sid-map, on page 792• continue, on page 793• contract-id, on page 794• control-plane, on page 795• control-plane dynamic, on page 796• control vlan, on page 797• control vlan, on page 798• controller-credentials username password 0, on page 799• controller description, on page 800• controller ip vrf, on page 801• controller ipv4, on page 802• controller ipv4, on page 803• controller type l2 identifier, on page 804• copp copy profile prefix, on page 805• copp distributed-policing enable, on page 806• copp profile, on page 807• copp profile, on page 808• copp rate-limit disable, on page 809• copy, on page 810• copy, on page 812• copy licenses, on page 813• copy licenses, on page 814• copy recursive, on page 815• copy running vdc-all, on page 816• copy vdc-all, on page 817• core-on-no-memory, on page 818• core-on-no-memory, on page 819• cost, on page 820• count, on page 821• count, on page 822• counter name value op, on page 823• crypto ca authenticate, on page 824• crypto ca crl request, on page 825• crypto ca enroll, on page 826• crypto ca export pkcs12, on page 827• crypto ca import certificate, on page 828• crypto ca import pkcs12, on page 829• crypto ca lookup, on page 830• crypto ca remote ldap, on page 831
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)321
C Commands
Page 466
• crypto ca test verify, on page 832• crypto ca trustpoint, on page 833• crypto ca trustpool import url, on page 834• crypto ca trustpool import url clean, on page 835• crypto ca trustpool policy, on page 836• crypto cert ssh-authorize, on page 837• crypto certificatemap mapname, on page 838• crypto key generate rsa, on page 839• crypto key param rsa label modulus, on page 840• crypto key zeroize rsa, on page 841• cryptographic-algorithm, on page 842• customer-id, on page 843• cut, on page 844
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)322
C Commands
Page 467
cabundle url[no] cabundle url <source_uri>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure cabundlecabundle
Configure cabundle urlurl
Select source http URLsource_uri
Command Mode
• /exec/configure/trustpool
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)323
C Commandscabundle url
Page 468
callhomecallhome
Syntax Description
Enter the callhome configuration modecallhome
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)324
C Commandscallhome
Page 469
callhome send configurationcallhome send configuration
Syntax Description
callhome commandscallhome
send a command callhome messagesend
configuration typeconfiguration
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)325
C Commandscallhome send configuration
Page 470
callhome send diagnosticcallhome send diagnostic
Syntax Description
callhome commandscallhome
send a command callhome messagesend
dignostic commanddiagnostic
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)326
C Commandscallhome send diagnostic
Page 471
callhome testcallhome test
Syntax Description
callhome commandscallhome
send a test callhome messagetest
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)327
C Commandscallhome test
Page 472
callhome test inventorycallhome test inventory
Syntax Description
callhome commandscallhome
send a test callhome messagetest
send a dummy callhome inventoryinventory
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)328
C Commandscallhome test inventory
Page 473
capability additional-paths receive[ no | default ] capability additional-paths receive [ disable ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Advertise capability to the peercapability
Additional paths capabilityadditional-paths
Additional paths Receive capabilityreceive
(Optional) Do not advertise additional paths Receive capabilitydisable
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)329
C Commandscapability additional-paths receive
Page 474
capability additional-paths send[ no | default ] capability additional-paths send [ disable ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Advertise capability to the peercapability
Additional paths capabilityadditional-paths
Additional paths Send capabilitysend
(Optional) Do not advertise additional paths Send capabilitydisable
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)330
C Commandscapability additional-paths send
Page 475
capability suppress 4-byte-as[ no | default ] capability suppress 4-byte-as
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Capabilitycapability
Suppress sending out capabilitysuppress
Suppress 4-byte AS Capability4-byte-as
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)331
C Commandscapability suppress 4-byte-as
Page 476
capability vrf-lite[no] capability vrf-lite [ evpn ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Capabilitycapability
Enable VRF-lite supportvrf-lite
(Optional) Ethernet VPNevpn
Command Mode
• /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)332
C Commandscapability vrf-lite
Page 477
capture[no] capture { buffer-drops | acl-drops | fwd-drops | blackhole }
Syntax Description
Events to be loggedcapture
Buffer dropsbuffer-drops
ACL dropsacl-drops
Forward dropsfwd-drops
Blackholeblackhole
Command Mode
• /exec/configure/config-fte-event/group-drop-events
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)333
C Commandscapture
Page 478
capture[no] capture { latency exceeding-threshold <time> { nano-sec | micro-sec | milli-sec } }
Syntax Description
Events to be loggedcapture
Latencylatency
Latency threshold limitexceeding-threshold
time range <0-65535>time
time in nano secondsnano-sec
time in micro secondsmicro-sec
time in milli secondsmilli-sec
Command Mode
• /exec/configure/config-fte-event/group-latency-events
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)334
C Commandscapture
Page 479
capture session[no] capture session <session-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable packet capture on this filter for sessioncapture
Session ID <1-48> for this sessionsession
Session ID <1-48> for this sessionsession-id
Command Mode
• /exec/configure/ipacl /exec/configure/ipv6acl /exec/configure/macacl /exec/configure/arpacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)335
C Commandscapture session
Page 480
carrier-delaycarrier-delay { <sec_val> | msec <msec_val> } | no carrier-delay
Syntax Description
Negate a command or set its defaultsno
Specify delay for interface transitionscarrier-delay
Carrier Transitions delay secondssec_val
Carrier Transitions delay millisecondsmsec
Carrier Transitions delay millisecondsmsec_val
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)336
C Commandscarrier-delay
Page 481
catena{ catena <instance-name> } | { no catena <instance-name> }
Syntax Description
Negate a command or set its defaultsno
instancecatena
instance-nameinstance-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)337
C Commandscatena
Page 482
catena device-group{ catena device-group <device-grp-name> } | { no catena device-group <device-grp-name> }
Syntax Description
Negate a command or set its defaultsno
instancecatena
device groupdevice-group
device-grp-namedevice-grp-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)338
C Commandscatena device-group
Page 483
catena port-acl{ catena port-acl <port-acl-name> } | { no catena port-acl <port-acl-name> }
Syntax Description
Negate a command or set its defaultsno
instancecatena
port aclport-acl
port-acl-nameport-acl-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)339
C Commandscatena port-acl
Page 484
catena port-group{ catena port-group <port-group-name> } | { no catena port-group <port-group-name> }
Syntax Description
Negate a command or set its defaultsno
instancecatena
port groupport-group
port-group-nameport-group-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)340
C Commandscatena port-group
Page 485
catena vlan-group{ catena vlan-group <vlan-grp-name> } | { no catena vlan-group <vlan-grp-name> }
Syntax Description
Negate a command or set its defaultsno
instancecatena
vlan groupvlan-group
vlan-grp-namevlan-grp-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)341
C Commandscatena vlan-group
Page 486
cbts-member tunnel-te[no] cbts-member tunnel-te <tunnel-num>
Syntax Description
(Optional) Negate a command or set its defaultsno
Member Tunnelcbts-member
Tunnel Interfacetunnel-te
Tunnel Interface numbertunnel-num
Command Mode
• /exec/configure/if-te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)342
C Commandscbts-member tunnel-te
Page 487
cdcd <uri0>
Syntax Description
Change current directorycd
Enter the name of the directoryuri0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)343
C Commandscd
Page 488
cdp advertise v1cdp advertise { v1 | v2 } | no cdp advertise [ v1 | v2 ]
Syntax Description
Negate a command or set its defaultsno
Configure CDP parameterscdp
Highest CDP version supported on the switchadvertise
CDP Version 1v1
CDP Version 2v2
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)344
C Commandscdp advertise v1
Page 489
cdp enable[no] cdp enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure CDP interface parameterscdp
Enable/disable CDP on all interfacesenable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)345
C Commandscdp enable
Page 490
cdp enable[no] cdp enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure CDP interface parameterscdp
Enable/disable CDP on the interfaceenable
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether/exec/configure/if-eth-base /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)346
C Commandscdp enable
Page 491
cdp format device-id[no] cdp format device-id { mac-address | serial-number | system-name }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure CDP parameterscdp
Device ID format for CDPformat
Device ID format for CDPdevice-id
Mac-address of the Chassismac-address
Chassis Serial Number/OUIserial-number
System name/Fully Qualified Domain Name (Default)system-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)347
C Commandscdp format device-id
Page 492
cdp holdtime[no] cdp holdtime <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure CDP parameterscdp
CDP hold time advertised (in seconds)holdtime
CDP hold time advertised (in seconds)i0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)348
C Commandscdp holdtime
Page 493
cdp timer[no] cdp timer <i1>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure CDP parameterscdp
CDP refresh time interval (in seconds)timer
CDP refresh time interval (in seconds)i1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)349
C Commandscdp timer
Page 494
certificatecertificate <file-name> <host-name> | no certificate
Syntax Description
Negate a command or set its defaultsno
Specify certificatecertificate
.pem certificate filenamefile-name
hostname associated with certificatehost-name
Command Mode
• /exec/configure/telemetry
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)350
C Commandscertificate
Page 495
cfs debug allcfs debug all
Syntax Description
CFS parameterscfs
Internal command for debugsdebug
Internal command for debugsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)351
C Commandscfs debug all
Page 496
cfs distribute[no] cfs distribute
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable fabric wide distributiondistribute
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)352
C Commandscfs distribute
Page 497
cfs eth cos{ cfs eth cos <i0> | no cfs eth cos [ <i0> ] }
Syntax Description
Negate a command or set its defaultsno
ETH configurationseth
Configure CFS Ethernet COS valuecos
COS Value Rangei0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)353
C Commandscfs eth cos
Page 498
cfs eth distribute[no] cfs eth distribute
Syntax Description
(Optional) Negate a command or set its defaultsno
ETH configurationseth
Enable CFS distribution over Ethernetdistribute
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)354
C Commandscfs eth distribute
Page 499
cfs ipv4 distribute[no] cfs ipv4 { distribute | mcast-address <ip0> }
Syntax Description
(Optional) Negate a command or set its defaultsno
IPv4 configurationsipv4
Enable CFS distribution over IPv4distribute
Configure IPv4 multicast addressmcast-address
Admin scope [239.255/16, 239.192/16-239.251/16]ip0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)355
C Commandscfs ipv4 distribute
Page 500
cfs ipv6 distribute[no] cfs ipv6 { distribute | mcast-address <ipv60> }
Syntax Description
(Optional) Negate a command or set its defaultsno
IPv6 configurationsipv6
Enable CFS distribution over IPv6distribute
Configure IPv6 multicast addressmcast-address
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)356
C Commandscfs ipv6 distribute
Page 501
cfs region[no] cfs region <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Regions to limit the distribution scope of application(s)region
Region Idi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)357
C Commandscfs region
Page 502
chain{ chain <chain-id> } | { no chain <chain-id> }
Syntax Description
Negate a command or set its defaultsno
chain for instancechain
chain IDchain-id
Command Mode
• /exec/configure/catena
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)358
C Commandschain
Page 503
change-passwordchange-password [ old-password <s1> new-password <s2> ]
Syntax Description
Change your passwordchange-password
(Optional) Current password for the userold-password
(Optional) Current password for the user (clear text)s1
(Optional) New password for the usernew-password
(Optional) New password for the user (clear text)s2
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)359
C Commandschange-password
Page 504
channel-group[no] channel-group
Syntax Description
Negate a command or set its defaultsno
Configure port channel parameterschannel-group
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)360
C Commandschannel-group
Page 505
channel-groupchannel-group <channel-id> | no channel-group
Syntax Description
Negate a command or set its defaultsno
add to/remove from a port-channelchannel-group
Specify a port-channel numberchannel-id
Command Mode
• /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext /exec/configure/if-gig-ether/exec/configure/if-fcip
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)361
C Commandschannel-group
Page 506
channel-groupchannel-group <channel-id> [ mode { active | passive | on } ]
Syntax Description
Configure port channel parameterschannel-group
(Optional) Specify channeling modemode
(Optional) Set channeling mode to ACTIVEactive
(Optional) Set channeling mode to PASSIVEpassive
(Optional) Set channeling mode to ONon
Specify a port-channel numberchannel-id
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)362
C Commandschannel-group
Page 507
channel-group[no] channel-group [ <channel-id> [ mode { active | passive | on } ] ]
Syntax Description
Negate a command or set its defaultsno
Configure port channel parameterschannel-group
(Optional) Specify channeling modemode
(Optional) Set channeling mode to ACTIVEactive
(Optional) Set channeling mode to PASSIVEpassive
(Optional) Set channeling mode to ONon
(Optional) Specify a port-channel numberchannel-id
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)363
C Commandschannel-group
Page 508
channel-group forcechannel-group <channel-id> force [ mode { active | passive | on } ] | no channel-group <channel-id> force [mode { active | passive | on } ]
Syntax Description
Negate a command or set its defaultsno
add to/remove from a port-channelchannel-group
Specify a port-channel numberchannel-id
Forcefully add a portforce
(Optional) Specify channeling modemode
(Optional) Set channeling mode to ACTIVEactive
(Optional) Set channeling mode to PASSIVEpassive
(Optional) Set channeling mode to ONon
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)364
C Commandschannel-group force
Page 509
channel-group forcechannel-group <channel-id> force
Syntax Description
add to/remove from a san-port-channelchannel-group
Specify a san-port-channel numberchannel-id
Forcefully add a portforce
Command Mode
• /exec/configure/if-fc /exec/configure/if-gig-ether /exec/configure/if-fcip
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)365
C Commandschannel-group force
Page 510
channel mode[no] channel mode
Syntax Description
Negate a command or set its defaultsno
Set the channel mode for the san-port-channel interfacechannel
Set the channel mode for the san-port-channel interfacemode
Command Mode
• /exec/configure/if-san-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)366
C Commandschannel mode
Page 511
channel mode activechannel mode active | no channel mode active
Syntax Description
Negate a command or set its defaultsno
Set the channel mode for the san-port-channel interfacechannel
Set the channel mode for the san-port-channel interfacemode
configure ACTIVE san-port-channelactive
Command Mode
• /exec/configure/if-san-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)367
C Commandschannel mode active
Page 512
chassis-family fretta[no] chassis-family fretta
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure chassis family typechassis-family
Confiure chassis family type to Frettafretta
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)368
C Commandschassis-family fretta
Page 513
checkpointcheckpoint { [ <name> ] [ description <descr_str> ] | file <file_uri> }
Syntax Description
Create configuration rollback checkpointcheckpoint
(Optional) Checkpoint namename
Create configuration rollback checkpoint to filefile
Checkpoint file pathfile_uri
(Optional) checkpoint description for the given checkpointdescription
(Optional) checkpoint description(can include spaces)descr_str
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)369
C Commandscheckpoint
Page 514
checkpoint[no] checkpoint <chkpoint_name>
Syntax Description
Negate a command or set its defaultsno
Delete configuration rollback checkpointcheckpoint
Checkpoint namechkpoint_name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)370
C Commandscheckpoint
Page 515
cipher-suite[no] cipher-suite <suite>
Syntax Description
Configure Cipher Suitecipher-suite
Cipher Suite optionssuite
Command Mode
• /exec/configure/macsec-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)371
C Commandscipher-suite
Page 516
class-map[no] class-map [ type qos ] [ <any_or_all> ] <cmap-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a class mapclass-map
(Optional) Specify the type of this class-maptype
(Optional) Qos classqos
(Optional) Enter match-any or match-allany_or_all
class-map namecmap-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)372
C Commandsclass-map
Page 517
class-map type control-plane[no] class-map type control-plane [ <opt_any_or_all> ] <cmap-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a class mapclass-map
Specify the type of this class-maptype
Control-Planecontrol-plane
(Optional) Enter match-any or match-allopt_any_or_all
Class-map namecmap-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)373
C Commandsclass-map type control-plane
Page 518
class-map type network-qos[no] class-map type network-qos [ match-any ] <cmap-name-nq>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a class mapclass-map
Specify the type of this class-maptype
Network QoS classnetwork-qos
(Optional) Match on any criteriamatch-any
class-map namecmap-name-nq
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)374
C Commandsclass-map type network-qos
Page 519
class-map type psp[no] class-map type psp [ <any_or_all> ] { <cmap-name-plc> | { handle <ppf_id> } } [ sequence <seq_no>] [ client <clienttype> <clientID> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a class mapclass-map
Specify the type of this class-maptype
PSP classpsp
(Optional) Enter match-any or match-allany_or_all
class-map namecmap-name-plc
Handlehandle
PPF IDppf_id
(Optional) sequencesequence
(Optional) Sequence numberseq_no
(Optional) set client typeclient
(Optional) cli/onepclienttype
(Optional) client appIDclientID
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)375
C Commandsclass-map type psp
Page 520
class-map type queuing[no] class-map type queuing { <cmap-dce-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a class mapclass-map
Specify the type of this class-maptype
Queuing classqueuing
Queuing class-map namecmap-dce-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)376
C Commandsclass-map type queuing
Page 521
class-map type queuing[no] class-map type queuing [ <any_or_all> ] { xxx <cmap-enum-name> | <cmap-dce-name> | zzz<cmap-name-hque> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a class mapclass-map
Specify the type of this class-maptype
Queuing classqueuing
(Optional) Enter match-anyany_or_all
cmap-enum-name
xxxxxx
zzzzzz
Queuing class-map namecmap-dce-name
Hierarchical class-map namecmap-name-hque
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)377
C Commandsclass-map type queuing
Page 522
class[no] class [ type qos ] <cmap-name> [ insert-before [ type qos1 ] <cmap-name2> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Policy Criteriaclass
(Optional) Specify the type of classtype
(Optional) Match on Qos classqos
class map namecmap-name
(Optional) Insert this class before another classinsert-before
(Optional) Insert before Qos classqos1
(Optional) class map namecmap-name2
Command Mode
• /exec/configure/policy-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)378
C Commandsclass
Page 523
classclass { <cmap-name> [ insert-before <cmap-name2> ] | class-default } | no class { <cmap-name> | class-default}
Syntax Description
Negate a command or set its defaultsno
Attach class map to policy mapclass
Class-map namecmap-name
(Optional) Insert this class before another classinsert-before
(Optional) class map name before which insertion should happencmap-name2
Use class defaultclass-default
Command Mode
• /exec/configure/pmap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)379
C Commandsclass
Page 524
class __inline__[no] class __inline__ [ type psp ] <cmap-name-plc> [ insert-before <cmap-name2> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Policy Criteriaclass
Inline Class__inline__
(Optional) Specify the type of classtype
(Optional) Match on PSP classpsp
class map namecmap-name-plc
(Optional) Insert this class before another classinsert-before
(Optional) class map namecmap-name2
Command Mode
• /exec/configure/policy-map/type/plc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)380
C Commandsclass __inline__
Page 525
class class-default[no] class class-default
Syntax Description
(Optional) Negate a command or set its defaultsno
Policy Criteriaclass
System default class matching otherwise unclassified packetsclass-default
Command Mode
• /exec/configure/policy-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)381
C Commandsclass class-default
Page 526
class type network-qos[no] class type network-qos <cmap-name-nq>
Syntax Description
(Optional) Negate a command or set its defaultsno
Match on network-qos class-mapclass
Specify the type of this class-maptype
Network QoS policynetwork-qos
Match class-map namecmap-name-nq
Command Mode
• /exec/configure/policy-map/type/uf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)382
C Commandsclass type network-qos
Page 527
class type network-qos class-default[no] class type network-qos class-default
Syntax Description
(Optional) Negate a command or set its defaultsno
Match on network-qos class-mapclass
Specify the type of this class-maptype
Network QoS policynetwork-qos
System default class matching otherwise not classified cos valuesclass-default
Command Mode
• /exec/configure/policy-map/type/uf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)383
C Commandsclass type network-qos class-default
Page 528
class type psp[no] class type psp { <cmap-name-plc> | { handle1 <ppf_id1> } } [ insert-before { <cmap-name2> | { handle2<ppf_id2> } } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Policy Criteriaclass
Specify the type of classtype
Match on PSP classpsp
class map namecmap-name-plc
Handle1handle1
PPF ID1ppf_id1
(Optional) Insert this class before another classinsert-before
(Optional) class map namecmap-name2
(Optional) Handle2handle2
(Optional) PPF ID2ppf_id2
Command Mode
• /exec/configure/policy-map/type/plc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)384
C Commandsclass type psp
Page 529
class type queuing[no] class type queuing { xxx <cmap-enum-name> | <cmap-dce-name> | zzz <cmap-name-hque> } [insert-before type queuing1 yyy <xcmap-enum-name> ]
Syntax Description
xxxxxx
(Optional) yyyyyy
zzzzzz
(Optional) Negate a command or set its defaultsno
Policy Criteriaclass
Specify the type of classtype
Match on Queuing classqueuing
cmap-enum-name
Queuing class-map namecmap-dce-name
Hierarchical class-map namecmap-name-hque
(Optional) Insert this class before another classinsert-before
(Optional) Insert before Queuing classqueuing1
(Optional)xcmap-enum-name
Command Mode
• /exec/configure/policy-map/type/queuing
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)385
C Commandsclass type queuing
Page 530
clearclear { { ip eigrp [ <eigrp-ptag> ] neighbors { * | <address> | <interface> } [ soft ] [ no-goodbye ] [ vrf {<vrf-name> | <vrf-known-name> | all } ] } | { ipv6 eigrp [ <eigrp-ptag> ] neighbors { * | <ipv6-addr> |<interface> } [ soft ] [ no-goodbye ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] } }
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IPv6 commandsipv6
EIGRP clear commandseigrp
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
(Optional) Process tageigrp-ptag
Clear EIGRP neighborsneighbors
Clear all EIGRP neighbors*
IP-EIGRP neighbor addressaddress
Interfaceinterface
(Optional) Soft resetsoft
(Optional) No goodbyeno-goodbye
(Optional)eigrp-ptag
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)386
C Commandsclear
Page 531
clearclear { { ip eigrp [ <eigrp-ptag> ] topology { { <address> <mask> } | { <prefix> } } [ vrf { <vrf-name> |<vrf-known-name> | all } ] } | { ipv6 eigrp [ <eigrp-ptag> ] topology { <ipv6-prefix> } [ vrf { <vrf-name> |<vrf-known-name> | all } ] } }
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IPv6 commandsipv6
EIGRP clear commandseigrp
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
(Optional) Process tageigrp-ptag
Clear IP-EIGRP topology table entrytopology
Network to display information aboutaddress
Network maskmask
IP prefix <network>/<length>, e.g., 192.168.0.0/16prefix
(Optional)eigrp-ptag
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)387
C Commandsclear
Page 532
clearclear { { ipv6 route [ vrf { <vrf-name> | <vrf-known-name> | <vrf-all> } ] } | { routing [ vrf { <vrf-name> |<vrf-known-name> } ] ipv6 [ unicast ] [ topology <topology-name> ] } } { <all> | { { <ipv6-addr> |<ipv6-prefix> } [ <nh-addr> <nh-interface> ] } } [ no-ufdm ]
Syntax Description
Reset functionsclear
Clear routing informationroute
Clear routing informationrouting
(Optional) Clear per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsvrf-all
Clear IPv6 commandsipv6
(Optional) Clear unicast informationunicast
(Optional) Clear per-topology informationtopology
(Optional) Topology nametopology-name
Clear all routesall
(Optional) Interface Namenh-interface
(Optional) Do not tell UFDM about the changeno-ufdm
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)388
C Commandsclear
Page 533
clearclear { { ip route [ vrf { <vrf-name> | <vrf-known-name> | <vrf-all> } ] } | { routing [ vrf { <vrf-name> |<vrf-known-name> } ] [ ip | ipv4 ] [ unicast ] [ topology <topology-name> ] } } { <all> | { { <ip-addr> |<ip-prefix> } [ { [ <nh-addr> | <nh-addr-v6> ] [ <nh-interface> ] } | { <nh-label> } ] } } [ no-ufdm ]
Syntax Description
Reset functionsclear
Clear routing informationroute
Clear routing informationrouting
(Optional) Clear per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsvrf-all
Clear IP commandsip
(Optional) Clear IP commandsipv4
(Optional) Clear unicast informationunicast
(Optional) Clear per-topology informationtopology
(Optional) Topology nametopology-name
Clear all routesall
Clear single host routeip-addr
Clear single exact match routeip-prefix
(Optional) Clear single pathnh-addr
(Optional) Clear single binding label pathnh-label
(Optional) Interface Namenh-interface
(Optional) Do not tell UFDM about the changeno-ufdm
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)389
C Commandsclear
Page 534
clear aaa local user blocked usernameclear aaa local user blocked { username <s0> | all }
Syntax Description
Reset functionsclear
Configure aaa functionsaaa
Local usernamelocal
Local system useruser
Clear blocked userblocked
Blocked usernameusername
Enter the usernames0
Clear all the blocked usersall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)390
C Commandsclear aaa local user blocked username
Page 535
clear access-list countersclear [ <ip_ipv6_mac> ] access-list counters [ <name> ]
Syntax Description
Reset functionsclear
(Optional) IP/IPv6/MACip_ipv6_mac
Clear access list statistical informationaccess-list
Clear access list counterscounters
(Optional) List namename
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)391
C Commandsclear access-list counters
Page 536
clear access-list hardware countersclear access-list hardware counters [ module <module> ]
Syntax Description
Reset functionsclear
Clear access list statistical informationaccess-list
hardware informationhardware
Clear access list counterscounters
(Optional) Slot/modulemodule
(Optional) Slot/module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)392
C Commandsclear access-list hardware counters
Page 537
clear access-list ipsg statsclear access-list ipsg stats [ module <module> ] [ instance <instance_number> ]
Syntax Description
Reset functionsclear
access-listaccess-list
ipsgipsg
Clear Statistics of IPSG drop entriesstats
(Optional) Slot/modulemodule
(Optional) Slot/module numbermodule
(Optional) ASIC Instance Numberinstance
(Optional) ASIC Instance Number in Decimalinstance_number
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)393
C Commandsclear access-list ipsg stats
Page 538
clear accounting logclear accounting log
Syntax Description
Reset functionsclear
Clear accounting log(s) in all vdcsaccounting
Clear the accounting log(s) in all vdcslog
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)394
C Commandsclear accounting log
Page 539
clear aclqos cl-qosclear aclqos cl-qos
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
cl-qos logs of ACLQOScl-qos
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)395
C Commandsclear aclqos cl-qos
Page 540
clear aclqos fabclear aclqos fab
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
Fabric logs of ACLQOSfab
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)396
C Commandsclear aclqos fab
Page 541
clear aclqos fcclear aclqos fc
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
fc logs of ACLQOSfc
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)397
C Commandsclear aclqos fc
Page 542
clear aclqos libdrvclear aclqos libdrv
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
libdrv logs of ACLQOSlibdrv
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)398
C Commandsclear aclqos libdrv
Page 543
clear aclqos mapclear aclqos map
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
map logs of ACLQOSmap
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)399
C Commandsclear aclqos map
Page 544
clear aclqos mergeclear aclqos merge
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
merge logs of ACLQOSmerge
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)400
C Commandsclear aclqos merge
Page 545
clear aclqos plclear aclqos pl
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
pl logs of ACLQOSpl
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)401
C Commandsclear aclqos pl
Page 546
clear aclqos ppf-parseclear aclqos ppf-parse
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
ppf-parse logs of ACLQOSppf-parse
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)402
C Commandsclear aclqos ppf-parse
Page 547
clear aclqos ppfclear aclqos ppf
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
ppf logs of ACLQOSppf
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)403
C Commandsclear aclqos ppf
Page 548
clear aclqos qng-hwclear aclqos qng-hw
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
Qng logs of ACLQOSqng-hw
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)404
C Commandsclear aclqos qng-hw
Page 549
clear aclqos qngclear aclqos qng
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
Qng logs of ACLQOSqng
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)405
C Commandsclear aclqos qng
Page 550
clear aclqos rlclear aclqos rl
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
RL logs of ACLQOSrl
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)406
C Commandsclear aclqos rl
Page 551
clear aclqos rmclear aclqos rm
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
RM logs of ACLQOSrm
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)407
C Commandsclear aclqos rm
Page 552
clear aclqos schclear aclqos sch
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
Sch logs of ACLQOSsch
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)408
C Commandsclear aclqos sch
Page 553
clear aclqos statsclear aclqos stats
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
stats logs of ACLQOSstats
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)409
C Commandsclear aclqos stats
Page 554
clear aclqos tblclear aclqos tbl
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
tbl logs of ACLQOStbl
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)410
C Commandsclear aclqos tbl
Page 555
clear aclqos trace-detailclear aclqos trace-detail
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
detail logs of ACLQOStrace-detail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)411
C Commandsclear aclqos trace-detail
Page 556
clear aclqos traceclear aclqos trace
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
trace logs of ACLQOStrace
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)412
C Commandsclear aclqos trace
Page 557
clear aclqos ufclear aclqos uf
Syntax Description
Reset functionsclear
Configure aclqos debugaclqos
UF logs of ACLQOSuf
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)413
C Commandsclear aclqos uf
Page 558
clear bfd statisticsclear bfd statistics
Syntax Description
Clearclear
bfdbfd
statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)414
C Commandsclear bfd statistics
Page 559
clear bgpclear bgp { ipv4 { unicast | multicast } policy statistics { { redistribute [ { { eigrp | isis | ospf | rip } <tag> } |static | direct | amt | lisp | hmm | am ] } | { neighbor <neighbor-id> [ default-originate | { route-map | filter-list| prefix-list } { in | out } ] } | { dampening } | { network { <ip-addr> mask <ip-mask> | <ip-prefix> } } | {aggregate-address { <ip-addr> <ip-mask> | <ip-prefix> } { suppress-map | advertise-map } } } | { vpnv4 |vpnv6 } unicast policy statistics { neighbor <neighbor-id> [ { route-map | filter-list | prefix-list } { in | out }] } | ipv6 { unicast | multicast } policy statistics { { redistribute [ { { eigrp | isis | ospfv3 | rip } <tag> } | static| direct | amt | lisp | hmm | am ] } | { neighbor { <neighbor-id> | <ipv6-neighbor-id> } [ default-originate | {route-map | filter-list | prefix-list } { in | out } ] } | { dampening } | { network <ipv6-prefix> } | {aggregate-address <ipv6-prefix> { suppress-map | advertise-map } } } }
Syntax Description
Reset functionsclear
Clear IPv4 address-familyipv4
Clear IPv6 address-familyipv6
Clear VPNv4 address-familyvpnv4
Clear VPNv6 address-familyvpnv6
Clear BGP sessionsbgp
Clear unicast address-familyunicast
Clear multicast address-familymulticast
Clear policy related informationpolicy
Clear Route Filter statisticsstatistics
Statistics for redistributionredistribute
(Optional) ISO IS-ISisis
(Optional) Open Shortest Path First (OSPF)ospf
(Optional) Open Shortest Path First v3ospfv3
(Optional) Routing Information Protocolrip
(Optional) Enhanced Interior Gateway Protocoleigrp
(Optional) Static routesstatic
(Optional) Directly connecteddirect
(Optional) AMT anycast prefixamt
(Optional) LISP EID-prefixes in the non-default VRFlisp
(Optional) HMM prefixhmm
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)415
C Commandsclear bgp
Page 560
(Optional) AM routes (learned via ARP)am
(Optional) Source protocol tagtag
Clear neighbor specific countersneighbor
Neighbor IPv4 addressneighbor-id
(Optional) Neighbor route-maproute-map
(Optional) Neighbor prefix-listprefix-list
(Optional) Neighbor filter-listfilter-list
(Optional) Outbound policyout
(Optional) Inbound policyin
(Optional) Default-originate policydefault-originate
Clear dampening infodampening
Configured IP prefix to advertisenetwork
Configured BGP aggregate prefixesaggregate-address
Statistics of suppress policysuppress-map
Statistics of advertise policyadvertise-map
IP network advertisedip-addr
Configured mask of the IP prefix advertisedmask
Dotted 4-octet maskip-mask
IP prefix in CIDR formatip-prefix
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)416
C Commandsclear bgp
Page 561
clear bgp bmp stats serverclear bgp bmp stats server { <server-id> | all }
Syntax Description
Reset functionsclear
Clear BGP sessionsbgp
Clear BMPbmp
Server Statsstats
BMP Serverserver
Server IDserver-id
All BMP Serversall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)417
C Commandsclear bgp bmp stats server
Page 562
clear bgp event-historyclear bgp event-history { <bgp-event-hist> | detail | periodic | errors | objstore | developer | all | msgs }
Syntax Description
Reset functionsclear
Clear BGP sessionsbgp
Clear event-history buffersevent-history
Event Historybgp-event-hist
Show error logs of BGPerrors
Show objstore logs of BGPobjstore
Show developer logs of BGPdeveloper
Show periodic logs of BGPperiodic
Show detailed event logsdetail
All event history buffersall
Clear message logs of BGPmsgs
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)418
C Commandsclear bgp event-history
Page 563
clear bgp privateclear bgp private { all | global | threads | session | debug | io | memory | af | damp | lists | attr [ <ip-prefix> |<ipv6-prefix> ] | rpm-info [ <rpm-name> { <ip-prefix> | <ipv6-prefix> } ] | neighbor { <neighbor-id> |<ipv6-neighbor-id> } | slab | mqstat | ipc | rnh | rpm-attribute-cache | rpm-comm-attr-cache | peer-template<peer-template-name> | aggregates [ summary ] | bestpath }
Syntax Description
Reset functionsclear
Clear BGP sessionsbgp
Clear internal BGP countersprivate
Clear all infoall
Clear global infoglobal
Clear thread infothreads
Clear session infosession
Clear debug infodebug
Clear IO infoio
Clear memory infomemory
Clear AF infoaf
Clear dampening infodamp
Clear BGP internal listslists
Clear BGP attributesattr
Clear BGP policy outbound inforpm-info
(Optional) Clear attribute for a prefixip-prefix
Clear neighbor specific countersneighbor
Neighbor IP addressneighbor-id
(Optional) Route-map namerpm-name
Clear information about SLABs usedslab
Clear message queue statsmqstat
Clear ipc informationipc
Clear recursive next hopsrnh
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)419
C Commandsclear bgp private
Page 564
Clear information about aggregatesaggregates
Clear rpm attribute cache statisticsrpm-attribute-cache
Clear rpm community attribute cache statisticsrpm-comm-attr-cache
Clear information about a peer-templatepeer-template
Clear internal information about bestpathbestpath
(Optional) Summary onlysummary
Peer-template namepeer-template-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)420
C Commandsclear bgp private
Page 565
clear bootvar logclear bootvar log
Syntax Description
Reset functionsclear
Clear the bootvar logbootvar
Clear the bootvar loglog
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)421
C Commandsclear bootvar log
Page 566
clear cdp countersclear cdp { counters [ interface <if0> ] | table [ interface1 <if1> ] }
Syntax Description
Reset functionsclear
Cisco Discovery Protocolcdp
Clear CDP counters on all interfacescounters
(Optional) Clear CDP counters on an interfaceinterface
(Optional)if0
Clear CDP cache on all interfacestable
(Optional) Clear CDP cache on an interfaceinterface1
(Optional)if1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)422
C Commandsclear cdp counters
Page 567
clear checkpoint databaseclear checkpoint database [ user | system ]
Syntax Description
Reset functionsclear
Clear configuration rollback checkpointcheckpoint
Clear configuration rollback checkpoint databasedatabase
(Optional) Clear configuration rollback checkpoint database for usercheckpoints
user
(Optional) Clear configuration rollback checkpoint database for systemcheckpoints
system
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)423
C Commandsclear checkpoint database
Page 568
clear cli historyclear cli history
Syntax Description
Reset functionsclear
debug clicli
history of cli commandshistory
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)424
C Commandsclear cli history
Page 569
clear controller accounting logclear controller <ctrl-id> accounting log
Syntax Description
Show running system informationclear
Controller commandcontroller
Controller id valuectrl-id
Accountingaccounting
Clear log informationlog
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)425
C Commandsclear controller accounting log
Page 570
clear copp statisticsclear copp statistics
Syntax Description
Reset functionsclear
Clear policy information for coppcopp
Clear statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)426
C Commandsclear copp statistics
Page 571
clear coresclear cores
Syntax Description
Reset functionsclear
clear all core dumps for the switchcores
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)427
C Commandsclear cores
Page 572
clear cores archiveclear cores archive [ file <s0> ]
Syntax Description
Reset functionsclear
clear all cores for this vdccores
clear all core dump files for this vdc from logflash on this modulearchive
(Optional) delete a core file on logflashfile
(Optional) Name of file in directory 'cores0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)428
C Commandsclear cores archive
Page 573
clear countersclear counters
Syntax Description
Reset functionsclear
Clear counterscounters
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)429
C Commandsclear counters
Page 574
clear counters buffersclear counters buffers [ module <module> [ instance <instance> ] ] [ __readonly__ <clear_valid> ]
Syntax Description
Reset functionsclear
Clear counterscounters
Clear system buffer max cell usage counterbuffers
(Optional) Slot/modulemodule
(Optional) Slot/module numbermodule
(Optional) ASIC Instance Numberinstance
(Optional) ASIC Instance Number in Decimalinstance
(Optional) Read Only__readonly__
(Optional) Clearclear_valid
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)430
C Commandsclear counters buffers
Page 575
clear counters interfaceclear counters interface <ifid>
Syntax Description
Reset functionsclear
Clear counterscounters
Clear interface countersinterface
Clear interface countersifid
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)431
C Commandsclear counters interface
Page 576
clear counters interfaceclear counters interface <ifindex1>
Syntax Description
Reset functionsclear
Clear counterscounters
Clear interface countersinterface
Clear interface countersifindex1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)432
C Commandsclear counters interface
Page 577
clear counters interfaceclear counters interface <ifindex>
Syntax Description
Reset functionsclear
Clear counterscounters
Clear interface countersinterface
Clear interface countersifindex
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)433
C Commandsclear counters interface
Page 578
clear counters interface allclear counters interface all
Syntax Description
Reset functionsclear
Clear counterscounters
Clear interface countersinterface
Clear all interface countersall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)434
C Commandsclear counters interface all
Page 579
clear counters interface snmpclear counters interface <ifindex> snmp
Syntax Description
Reset functionsclear
Clear counterscounters
Clear interface countersinterface
Clear interface countersifindex
Clear snmp interface counterssnmp
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)435
C Commandsclear counters interface snmp
Page 580
clear counters tah-buffersclear counters tah-buffers [ module <module> ] [ { instance <instance> | { unit <unit> slice <slice> } } ]
Syntax Description
Reset functionsclear
Clear counterscounters
Clear system buffer max cell usage countertah-buffers
(Optional) ASIC Instance Numberinstance
(Optional) ASIC Instance Number in Decimalinstance
(Optional) Asic Numberunit
(Optional) Asic Number on the moduleunit
(Optional) slice num on asicslice
(Optional) slice number on asicslice
(Optional) Slot/modulemodule
(Optional) Slot/module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)436
C Commandsclear counters tah-buffers
Page 581
clear crypto ca trustpool timerclear crypto ca trustpool timer
Syntax Description
Reset functionsclear
Set crypto settingscrypto
Configure certificate authority related informationca
certificate trustpooltrustpool
clear trustpool timertimer
Command Mode
• /exec/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)437
C Commandsclear crypto ca trustpool timer
Page 582
clear debug-logfileclear debug-logfile <s0>
Syntax Description
Reset functionsclear
Remove the debug logfiledebug-logfile
Provide name of the files0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)438
C Commandsclear debug-logfile
Page 583
clear debug logfileclear debug logfile <s0>
Syntax Description
Reset functionsclear
Debugging functionsdebug
Remove the debug logfilelogfile
Provide name of the files0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)439
C Commandsclear debug logfile
Page 584
clear dot1x all{ clear dot1x all } | { clear dot1x interface <if> } | { clear dot1x mac <addr> }
Syntax Description
Reset functionsclear
dot1x configuration commandsdot1x
Authenticator instances on all interfacesall
Specific MAC address of the Supplicantmac
target interfaceif
MAC Addressaddr
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)440
C Commandsclear dot1x all
Page 585
clear dot1x stats interface{ clear dot1x stats interface <if> } | { clear dot1x stats mac <addr> }
Syntax Description
Reset functionsclear
dot1x configuration commandsdot1x
clear statsstats
Specific MAC address of the Supplicantmac
target interfaceif
MAC Addressaddr
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)441
C Commandsclear dot1x stats interface
Page 586
clear ecp statisticsclear ecp statistics
Syntax Description
Reset functionsclear
ECP (Edge Control Protocol)ecp
Clear ECP Statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)442
C Commandsclear ecp statistics
Page 587
clear eigrp event-historyclear eigrp [ <eigrp-ptag> ] event-history [ cli | notifications | all ]
Syntax Description
Reset functionsclear
EIGRP clear commandseigrp
(Optional) Process tageigrp-ptag
Clear the event history buffersevent-history
(Optional) EIGRP Notificationsnotifications
(Optional) EIGRP CLI related eventscli
(Optional) All event history buffersall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)443
C Commandsclear eigrp event-history
Page 588
clear evb hostsclear evb { hosts | vsi } [ force-standby ] [ { [ mac <mac-addr> | interface <intf-name> | vlan <vlan-id> | vni<vni-id> | ip <ip-addr> | ipv6 <ipv6-addr> ] + } ]
Syntax Description
Reset functionsclear
EVB (Edge Virtual Bridge)evb
Clear EVB host informationhosts
Clear EVB vsi informationvsi
(Optional) Force to clear standby entriesforce-standby
(Optional) Clear entries by filtering MAC addressmac
(Optional) MAC Addressmac-addr
(Optional) Clear entries by filtering interfaceinterface
(Optional) Interface nameintf-name
(Optional) Clear entries by filtering VLANvlan
(Optional) VLAN IDvlan-id
(Optional) Clear entries by filtering VNIvni
(Optional) VNIvni-id
(Optional) Clear entries by filtering IP addressip
(Optional) Clear entries by filtering IPv6 addressipv6
(Optional) IPV4 host addressip-addr
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)444
C Commandsclear evb hosts
Page 589
clear evb hostsclear evb { hosts | vsi } [ force-standby ] *
Syntax Description
Reset functionsclear
EVB (Edge Virtual Bridge)evb
Clear EVB host informationhosts
Clear EVB vsi informationvsi
(Optional) Force to clear standby entriesforce-standby
Clear all entries (Should be a * character)*
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)445
C Commandsclear evb hosts
Page 590
clear evb statisticsclear evb statistics
Syntax Description
Reset functionsclear
EVB (Edge Virtual Bridge)evb
Clear EVB Statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)446
C Commandsclear evb statistics
Page 591
clear fabric database dci vrf node-idclear fabric database dci vrf { <vrf-name> | <vrf-known-name> } node-id <mgmt-ip-address> [ peer-id<peer-ip-address> ]
Syntax Description
Reset functionsclear
Fabricfabric
Fabric Databasedatabase
DCI profiledci
Display per-VRF informationvrf
VRF namevrf-name
Known VRF namevrf-known-name
management ip address of this nodenode-id
IP address in CIDR formatmgmt-ip-address
(Optional) management ip address of peerpeer-id
(Optional) IP address in CIDR formatpeer-ip-address
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)447
C Commandsclear fabric database dci vrf node-id
Page 592
clear fabric database host all vni{ clear fabric database host { all | { vni <vni-id> } | { dot1q <vlan-id> } } [ re-sync ] } | { clear fabric databasehost vni <vni-id> re-apply } | { clear fabric database client uuid <uuid> }
Syntax Description
Reset functionsclear
fabric
database
Active Host to profile mappinghost
Virtual Network Identifiervni
vni-id
Dot1Q Encapsulationdot1q
vlan-id
Download new config parameters and re-applyre-apply
(Optional) Force to sync the host entryre-sync
Remove all entriesall
Auto-config clientclient
Auto-config client UUIDuuid
UUIDuuid
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)448
C Commandsclear fabric database host all vni
Page 593
clear fabric database host statisticsclear fabric database host statistics
Syntax Description
Reset functionsclear
Fabricfabric
Fabric Databasedatabase
Auto-configured Hostshost
Statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)449
C Commandsclear fabric database host statistics
Page 594
clear fabric database include-vrfclear fabric database include-vrf <vrf-name>
Syntax Description
Reset functionsclear
fabric
database
Include VRF nameinclude-vrf
VRF namevrf-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)450
C Commandsclear fabric database include-vrf
Page 595
clear fabric database statisticsclear fabric database statistics [ type { network | profile | cabling | partition | bl-dci } [ server-proto ldap { ipv6<ipv6addr> | ip <ipaddr> | host <hostname> } [ port <portnum> ] [ vrf { <vrf-name> | <vrf-known-name> }] ] ]
Syntax Description
Reset functionsclear
Fabricfabric
Clear Fabric Databasedatabase
Clear database statisticsstatistics
(Optional) Enter database typetype
(Optional) Network Databasenetwork
(Optional) Port or Switch Profile Databaseprofile
(Optional) Cable Management Databasecabling
(Optional) Partition Databasepartition
(Optional) Border Leaf - DCIbl-dci
(Optional) Enter database protocolserver-proto
(Optional) Use LDAPldap
(Optional) IPv6 address of serveripv6
(Optional) IP address of serverip
(Optional) Enter IP address of serveripaddr
(Optional) Hostname of serverhost
(Optional) Enter hostname of serverhostname
(Optional) Portport
(Optional) Enter port numberportnum
(Optional) vrf contextvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)451
C Commandsclear fabric database statistics
Page 596
clear fabric database statistics type server-proto radius groupclear fabric database statistics type { network | profile | cabling | partition | bl-dci } server-proto radius group<groupname>
Syntax Description
Reset functionsclear
Fabricfabric
Clear Fabric Databasedatabase
Clear database statisticsstatistics
Enter database typetype
Network Databasenetwork
Port or Switch Profile Databaseprofile
Cable Management Databasecabling
Partition Databasepartition
Border Leaf - DCIbl-dci
Enter database protocolserver-proto
Use RADIUSradius
AAA groupgroup
Enter AAA group name of serversgroupname
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)452
C Commandsclear fabric database statistics type server-proto radius group
Page 597
clear fabric database statistics type server-proto xmpp ipclear fabric database statistics type { network | profile | cabling | partition | bl-dci } server-proto xmpp { ip<ipaddr> | host <hostname> } [ port <portnum> ] [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
Reset functionsclear
Fabricfabric
Clear Fabric Databasedatabase
Clear database statisticsstatistics
Enter database typetype
Network Databasenetwork
Port or Switch Profile Databaseprofile
Cable Management Databasecabling
Partition Databasepartition
Border Leaf - DCIbl-dci
Enter database protocolserver-proto
Use XMPPxmpp
IP address of serverip
Enter IP address of serveripaddr
Hostname of serverhost
Enter hostname of serverhostname
(Optional) Portport
(Optional) Enter port numberportnum
(Optional) vrf contextvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)453
C Commandsclear fabric database statistics type server-proto xmpp ip
Page 598
clear fabric multicast event-historyclear fabric multicast event-history [ <ngmvpn-event-hist-buf-name> ]
Syntax Description
Reset functionsclear
Fabricfabric
Multicast informationmulticast
Clear event history buffersevent-history
(Optional) Event history buffer instancengmvpn-event-hist-buf-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)454
C Commandsclear fabric multicast event-history
Page 599
clear fc2clear fc2 [ counters ]
Syntax Description
Reset functionsclear
Clear FC2 Port Countersfc2
(Optional) Clear All FC2/FCoE Port Counterscounters
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)455
C Commandsclear fc2
Page 600
clear fctimer sessionclear fctimer session
Syntax Description
Reset functionsclear
clear fctimer cfs sessionfctimer
abort an existing cfs sessionsession
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)456
C Commandsclear fctimer session
Page 601
clear flow cacheclear flow cache [ ipv4 | ipv6 | ce ] [ force-export ]
Syntax Description
Reset functionsclear
NetFlow informationflow
Clear only cache contentscache
(Optional) Show ipv4 cache entriesipv4
(Optional) Show ipv6 cache entriesipv6
(Optional) Show ce cache entriesce
(Optional) Force the cache entries to be exportedforce-export
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)457
C Commandsclear flow cache
Page 602
clear flow cacheclear flow cache [ ipv4 | ipv6 | ce ] [ force-export ]
Syntax Description
Reset functionsclear
NetFlow informationflow
Clear only cache contentscache
(Optional) Show ipv4 cache entriesipv4
(Optional) Show ipv6 cache entriesipv6
(Optional) Show ce cache entriesce
(Optional) Force the cache entries to be exportedforce-export
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)458
C Commandsclear flow cache
Page 603
clear flow exporterclear flow exporter { [ name ] <exportername> | all }
Syntax Description
Reset functionsclear
NetFlow informationflow
Clear NetFlow exporter statisticsexporter
(Optional) The name of the exportername
Specify an exporterexportername
Clear all exporter statisticsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)459
C Commandsclear flow exporter
Page 604
clear forwarding adjacency moduleclear forwarding [ ip | ipv4 ] { adjacency } [ vrf <vrf-name> ] { <ip-addr> | all_routes } module { all_modules| <module> } [ force-delete ] [ no-urib ]
Syntax Description
clear
forwarding informationforwarding
(Optional) ipv4ip
(Optional) ipv4ipv4
adjacencyadjacency
(Optional) delete routes for a specific vrfvrf
(Optional) VRF namevrf-name
IPV4 source addressip-addr
delete all routesall_routes
modulemodule
all module'sall_modules
module numbermodule
(Optional) Do not tell URIB about changesno-urib
(Optional) Forcefully remove adjforce-delete
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)460
C Commandsclear forwarding adjacency module
Page 605
clear forwarding cumulative counterclear forwarding cumulative counter [ all | v4_ucast_add | v4_ucast_del | v6_ucast_add | v6_ucast_del ] [module <module> ]
Syntax Description
clearclear
forwarding informationforwarding
accumulated prefix add/delete countcumulative
countercounter
(Optional) allall
(Optional) IPv4 unicast route add countv4_ucast_add
(Optional) IPv4 unicast route delete countv4_ucast_del
(Optional) IPv6 unicast route add countv6_ucast_add
(Optional) IPv6 unicast route delete countv6_ucast_del
(Optional) slotmodule
(Optional) slot numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)461
C Commandsclear forwarding cumulative counter
Page 606
clear forwarding distribution lisp counters allclear forwarding distribution lisp counters all
Syntax Description
clear
forwardingforwarding
fib distribution informationdistribution
lisp applicationlisp
counterscounters
all vrf'sall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)462
C Commandsclear forwarding distribution lisp counters all
Page 607
clear forwarding events-historyclear forwarding events-history
Syntax Description
Reset functionsclear
forwardingforwarding
Events historyevents-history
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)463
C Commandsclear forwarding events-history
Page 608
clear forwarding inconsistencyclear forwarding [ ipv4 | ip ] [ unicast ] inconsistency
Syntax Description
clearclear
forwardingforwarding
(Optional) ipv4ip
(Optional) ipv4ipv4
(Optional) unicastunicast
route inconsistency checkinconsistency
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)464
C Commandsclear forwarding inconsistency
Page 609
clear forwarding ipv4 multicast countersclear forwarding ipv4 multicast counters [ vrf { <vrf-name> | <vrf-known-name> | all } ] { [ group <gaddr>[ source <saddr> ] ] | [ source <saddr> [ group <gaddr> ] ] } [ module <module> ]
Syntax Description
clear
fib informationforwarding
(Optional) Specify VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Ipv4ipv4
Multicast IPv4 informationmulticast
counters
(Optional) Multicast IPv4 Group specific infogroup
(Optional) Multicast IPv4 Group Addressgaddr
(Optional) Multicast IPv4 Source specific infosource
(Optional) Multicast IPv4 Source Addresssaddr
(Optional) slotmodule
(Optional) slot numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)465
C Commandsclear forwarding ipv4 multicast counters
Page 610
clear forwarding ipv6-l3-route-historyclear forwarding ipv6-l3-route-history
Syntax Description
Reset functionsclear
forwardingforwarding
IPV6 L3 Route historyipv6-l3-route-history
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)466
C Commandsclear forwarding ipv6-l3-route-history
Page 611
clear forwarding ipv6 adjacency moduleclear forwarding ipv6 adjacency [ vrf <vrf-name> ] { <ip-addr> | all_adjs } module { all_modules | <module>} [ force-delete ] [ no-urib ]
Syntax Description
clear
forwarding informationforwarding
ipv6ipv6
adjacencyadjacency
(Optional) delete routes for a specific vrfvrf
(Optional) VRF namevrf-name
delete all adjsall_adjs
modulemodule
all module'sall_modules
module numbermodule
(Optional) Do not tell URIB about changesno-urib
(Optional) Forcefully remove adjforce-delete
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)467
C Commandsclear forwarding ipv6 adjacency module
Page 612
clear forwarding ipv6 inconsistencyclear forwarding ipv6 [ unicast ] inconsistency
Syntax Description
clearclear
forwardingforwarding
ipv6ipv6
(Optional) unicastunicast
route inconsistency checkinconsistency
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)468
C Commandsclear forwarding ipv6 inconsistency
Page 613
clear forwarding ipv6 multicast countersclear forwarding ipv6 multicast counters [ vrf { <vrf-name> | <vrf-known-name> | all } ] { [ group <gaddr>[ source <saddr> ] ] | [ source <saddr> [ group <gaddr> ] ] } [ module <module> ]
Syntax Description
clear
fib informationforwarding
(Optional) Specify VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Ipv6ipv6
Multicast IPv6 informationmulticast
counters
(Optional) Multicast IPv6 Group specific infogroup
(Optional) Multicast IPv6 Source specific infosource
(Optional) slotmodule
(Optional) slot numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)469
C Commandsclear forwarding ipv6 multicast counters
Page 614
clear forwarding ipv6 route moduleclear forwarding ipv6 { route } [ vrf <vrf-name> ] { <prefix> | all_routes } module { all_modules | <module>} [ no-urib ]
Syntax Description
clear
forwarding informationforwarding
ipv6ipv6
routeroute
(Optional) delete routes for a specific vrfvrf
(Optional) VRF namevrf-name
delete all routesall_routes
modulemodule
all module'sall_modules
module numbermodule
(Optional) Do not tell URIB about changesno-urib
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)470
C Commandsclear forwarding ipv6 route module
Page 615
clear forwarding l2-mc-route-historyclear forwarding l2-mc-route-history
Syntax Description
Reset functionsclear
forwardingforwarding
L2 MacgRoute historyl2-mc-route-history
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)471
C Commandsclear forwarding l2-mc-route-history
Page 616
clear forwarding l2-oiflist-historyclear forwarding l2-oiflist-history
Syntax Description
Reset functionsclear
forwardingforwarding
L2 Oiflist historyl2-oiflist-history
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)472
C Commandsclear forwarding l2-oiflist-history
Page 617
clear forwarding l2-route-historyclear forwarding l2-route-history
Syntax Description
Reset functionsclear
forwardingforwarding
L2 Route historyl2-route-history
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)473
C Commandsclear forwarding l2-route-history
Page 618
clear forwarding l2mcast info l2-mc-route-historyclear forwarding l2mcast info l2-mc-route-history [ module <num> ]
Syntax Description
Reset functionsclear
forwardingforwarding
l2mcastl2mcast
L2mcast Internal Infoinfo
L2 Macg Route historyl2-mc-route-history
(Optional) Slotmodule
(Optional) Slot numbernum
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)474
C Commandsclear forwarding l2mcast info l2-mc-route-history
Page 619
clear forwarding l2mcast info l2-oiflist-historyclear forwarding l2mcast info l2-oiflist-history [ module <num> ]
Syntax Description
Reset functionsclear
forwardingforwarding
l2mcastl2mcast
L2mcast Internal Infoinfo
L2 oiflist historyl2-oiflist-history
(Optional) Slotmodule
(Optional) Slot numbernum
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)475
C Commandsclear forwarding l2mcast info l2-oiflist-history
Page 620
clear forwarding l2mcast info l2-route-historyclear forwarding l2mcast info l2-route-history [ module <num> ]
Syntax Description
Reset functionsclear
forwardingforwarding
l2mcastl2mcast
L2mcast Internal Infoinfo
L2 Route historyl2-route-history
(Optional) Slotmodule
(Optional) Slot numbernum
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)476
C Commandsclear forwarding l2mcast info l2-route-history
Page 621
clear forwarding l2mcast info l2-xbar-historyclear forwarding l2mcast info l2-xbar-history [ module <num> ]
Syntax Description
Reset functionsclear
forwardingforwarding
l2mcastl2mcast
L2mcast Internal Infoinfo
L2 Route historyl2-xbar-history
(Optional) Slotmodule
(Optional) Slot numbernum
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)477
C Commandsclear forwarding l2mcast info l2-xbar-history
Page 622
clear forwarding l2mcast info statisticsclear forwarding l2mcast info statistics [ module <num> ]
Syntax Description
Clear all entriesclear
Forwarding Informationforwarding
Layer-2 multicastl2mcast
L2mcast Internal Infoinfo
L2mcast Internal Info Statisticsstatistics
(Optional) Slotmodule
(Optional) Slot numbernum
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)478
C Commandsclear forwarding l2mcast info statistics
Page 623
clear forwarding l2vpn trace member-historyclear forwarding l2vpn trace member-history
Syntax Description
Reset functionsclear
forwardingforwarding
L2VPNl2vpn
internal tracetrace
member historymember-history
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)479
C Commandsclear forwarding l2vpn trace member-history
Page 624
clear forwarding l3-route-historyclear forwarding l3-route-history
Syntax Description
Reset functionsclear
forwardingforwarding
L3 Route historyl3-route-history
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)480
C Commandsclear forwarding l3-route-history
Page 625
clear forwarding oiflist-historyclear forwarding oiflist-history
Syntax Description
Reset functionsclear
forwardingforwarding
Oiflist historyoiflist-history
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)481
C Commandsclear forwarding oiflist-history
Page 626
clear forwarding route moduleclear forwarding [ ip | ipv4 ] { route } [ vrf <vrf-name> ] { <prefix> | all_routes } module { all_modules |<module> } [ no-urib ]
Syntax Description
clear
forwarding informationforwarding
(Optional) ipv4ip
(Optional) ipv4ipv4
routeroute
(Optional) delete routes for a specific vrfvrf
(Optional) VRF namevrf-name
delete specific prefixprefix
delete all routesall_routes
modulemodule
all module'sall_modules
module numbermodule
(Optional) Do not tell URIB about changesno-urib
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)482
C Commandsclear forwarding route module
Page 627
clear forwarding trace ecmp-historyclear forwarding trace ecmp-history [ module <module> ]
Syntax Description
Reset functionsclear
forwardingforwarding
internal tracetrace
ECMP historyecmp-history
(Optional) slotmodule
(Optional) slot numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)483
C Commandsclear forwarding trace ecmp-history
Page 628
clear forwarding trace mfib oif-historyclear forwarding trace mfib oif-history
Syntax Description
Reset functionsclear
forwardingforwarding
internal tracetrace
mfib entriesmfib
oif historyoif-history
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)484
C Commandsclear forwarding trace mfib oif-history
Page 629
clear forwarding trace mfib oiflist-historyclear forwarding trace mfib oiflist-history
Syntax Description
Reset functionsclear
forwardingforwarding
internal tracetrace
mfib entriesmfib
oiflist historyoiflist-history
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)485
C Commandsclear forwarding trace mfib oiflist-history
Page 630
clear forwarding trace mfib platform oiflist-historyclear forwarding trace mfib platform oiflist-history
Syntax Description
Clearclear
Forwarding informationforwarding
internal tracetrace
mfib entriesmfib
platform informationplatform
Oiflist historyoiflist-history
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)486
C Commandsclear forwarding trace mfib platform oiflist-history
Page 631
clear forwarding trace mfib v4-route-historyclear forwarding trace mfib v4-route-history
Syntax Description
Reset functionsclear
forwardingforwarding
internal tracetrace
clear mfib entriesmfib
v4 route historyv4-route-history
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)487
C Commandsclear forwarding trace mfib v4-route-history
Page 632
clear forwarding trace mfib v6-route-historyclear forwarding trace mfib v6-route-history
Syntax Description
Reset functionsclear
forwardingforwarding
internal tracetrace
mfib entriesmfib
v6 route historyv6-route-history
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)488
C Commandsclear forwarding trace mfib v6-route-history
Page 633
clear forwarding trace v4-adj-historyclear forwarding trace v4-adj-history [ module <module> ]
Syntax Description
Reset functionsclear
forwardingforwarding
internal tracetrace
V4 adjacency historyv4-adj-history
(Optional) slotmodule
(Optional) slot numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)489
C Commandsclear forwarding trace v4-adj-history
Page 634
clear forwarding trace v4-pfx-historyclear forwarding trace v4-pfx-history [ module <module> ]
Syntax Description
Reset functionsclear
forwardingforwarding
internal tracetrace
V4 prefix historyv4-pfx-history
(Optional) slotmodule
(Optional) slot numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)490
C Commandsclear forwarding trace v4-pfx-history
Page 635
clear forwarding trace v4-rnh-historyclear forwarding trace v4-rnh-history [ module <module> ]
Syntax Description
Reset functionsclear
forwardingforwarding
internal tracetrace
V4 rnh historyv4-rnh-history
(Optional) slotmodule
(Optional) slot numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)491
C Commandsclear forwarding trace v4-rnh-history
Page 636
clear forwarding trace v6-adj-historyclear forwarding trace v6-adj-history [ module <module> ]
Syntax Description
Reset functionsclear
forwardingforwarding
internal tracetrace
V6 adjacency historyv6-adj-history
(Optional) slotmodule
(Optional) slot numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)492
C Commandsclear forwarding trace v6-adj-history
Page 637
clear forwarding trace v6-pfx-historyclear forwarding trace v6-pfx-history [ module <module> ]
Syntax Description
Reset functionsclear
forwardingforwarding
internal tracetrace
V6 prefix historyv6-pfx-history
(Optional) slotmodule
(Optional) slot numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)493
C Commandsclear forwarding trace v6-pfx-history
Page 638
clear forwarding trace v6-rnh-historyclear forwarding trace v6-rnh-history [ module <module> ]
Syntax Description
Reset functionsclear
forwardingforwarding
internal tracetrace
V6 rnh historyv6-rnh-history
(Optional) slotmodule
(Optional) slot numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)494
C Commandsclear forwarding trace v6-rnh-history
Page 639
clear forwarding trace vobj-historyclear forwarding trace vobj-history [ module <module> ]
Syntax Description
Reset functionsclear
forwardingforwarding
internal tracetrace
vobj historyvobj-history
(Optional) slotmodule
(Optional) slot numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)495
C Commandsclear forwarding trace vobj-history
Page 640
clear frame trafficclear frame traffic
Syntax Description
Reset functionsclear
Clear layer-2 frame statistics to/from the Route Processorframe
Clear layer-2 frame statistics to/from the Route Processortraffic
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)496
C Commandsclear frame traffic
Page 641
clear fs-daemon logclear fs-daemon log
Syntax Description
Reset functionsclear
Clear the fs daemon logfs-daemon
Clear the fs daemon loglog
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)497
C Commandsclear fs-daemon log
Page 642
clear hardware flow ipclear hardware flow ip [ { { monitor <mname> } | { profile <prof_id> } | { vlan <vlan_id> } | { interface<interface> } } ] [ instance <inst> ] [ force-export ] [ module <num> ]
Syntax Description
Reset functionsclear
Show hardware informationhardware
Netflow Moduleflow
Internet Protocol Version 4ip
(Optional) Netflow Flow Monitormonitor
(Optional) Netflow Flow Monitor Namemname
(Optional) Flow Profileprofile
(Optional) Netflow Profile IDprof_id
(Optional) Vlan commandsvlan
(Optional) VLAN ID 1-4094vlan_id
(Optional) Interfaceinterface
(Optional) Interface Nameinterface
(Optional) Instanceinstance
(Optional) Earl Instanceinst
(Optional) Force to export data to collectorforce-export
(Optional) Line card modulemodule
(Optional) slot numbernum
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)498
C Commandsclear hardware flow ip
Page 643
clear hardware flow ipv6clear hardware flow ipv6 [ { { monitor <mname> } | { profile <prof_id> } | { vlan <vlan_id> } | { interface<interface> } } ] [ instance <inst> ] [ force-export ] [ module <num> ]
Syntax Description
Reset functionsclear
Show hardware informationhardware
Netflow Moduleflow
Internet Protocol Version 6ipv6
(Optional) Netflow Flow Monitormonitor
(Optional) Netflow Flow Monitor Namemname
(Optional) Flow Profileprofile
(Optional) Netflow Profile IDprof_id
(Optional) Vlan commandsvlan
(Optional) VLAN ID 1-4094vlan_id
(Optional) Interfaceinterface
(Optional) Interface Nameinterface
(Optional) Instanceinstance
(Optional) Earl Instanceinst
(Optional) Force to export data to collectorforce-export
(Optional) Line card modulemodule
(Optional) slot numbernum
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)499
C Commandsclear hardware flow ipv6
Page 644
clear hardware flow l2clear hardware flow l2 [ { { monitor <mname> } | { profile <prof_id> } | { vlan <vlan_id> } } ] [ instance<inst> ] [ force-export ] [ module <num> ]
Syntax Description
Reset functionsclear
Show hardware informationhardware
Netflow Moduleflow
Layer 2 Protocoll2
(Optional) Netflow Flow Monitormonitor
(Optional) Netflow Flow Monitor Namemname
(Optional) Flow Profileprofile
(Optional) Netflow Profile IDprof_id
(Optional) Vlan commandsvlan
(Optional) VLAN ID 1-4094vlan_id
(Optional) Instanceinstance
(Optional) Earl Instanceinst
(Optional) Force to export data to collectorforce-export
(Optional) Line card modulemodule
(Optional) slot numbernum
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)500
C Commandsclear hardware flow l2
Page 645
clear hardware ip verifyclear hardware [ forwarding ] ip verify { all | address { source { broadcast | multicast } | class-e | destination{ zero } | identical | reserved } | checksum | protocol | fragment | length { minimum | consistent | maximum {max-frag | udp | max-tcp } } | tcp { tiny-frag } | version } [ module <module> ]
Syntax Description
Reset functionsclear
Show hardware informationhardware
(Optional) Show hardware information for forwarding pathforwarding
IPv4 and IPv6 protocolsip
IP packet validation checks in hardwareverify
Class E IDS checkclass-e
All IP packet validation checksall
IPv4 and IPv6 Source and destination address validationaddress
Check source addresssource
Source address is 255.255.255.255broadcast
Source address is 224.x.x.xmulticast
Check destination addressdestination
Destination address is 0.0.0.0zero
Same IP SA and DAidentical
Source address is 127.x.x.xreserved
Verify IPv4 and IPv6 packet checksumchecksum
Verify IP procotolprotocol
Check IPv4 and IPv6 fragment with non-zero offset and DF bit activefragment
Validate IPv4 packet header and payload lengthlength
Minimum IPv4 header lengthminimum
Actual frame size is equal to or more than IPv4 length plus ethernetheader
consistent
Check max fragment offset and payload lengthmaximum
Fragment offset field valuemax-frag
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)501
C Commandsclear hardware ip verify
Page 646
Maximum UDP length has to be less than IPv4 payload lengthudp
Maximum TCP length has to be less than IPv4 payload lengthmax-tcp
Validate TCP packet headertcp
Check TCP tiny fragmenttiny-frag
Must be 4 for an ethertype of IPv4 (0x0800)version
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)502
C Commandsclear hardware ip verify
Page 647
clear hardware profile buffer monitorclear hardware profile buffer monitor
Syntax Description
Reset functionsclear
Clear hardware profile buffer monitor datahardware
profile buffer monitor dataprofile
bufferbuffer
buffer monitormonitor
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)503
C Commandsclear hardware profile buffer monitor
Page 648
clear hardware profile latency monitorclear hardware profile latency monitor [ interface <intf-num> ]
Syntax Description
Reset functionsclear
Clear hardware profile latency monitor datahardware
profile latency monitor dataprofile
latencylatency
latency monitormonitor
(Optional) clear per-interface latency monitor datainterface
(Optional) clear per-interface latency monitor dataintf-num
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)504
C Commandsclear hardware profile latency monitor
Page 649
clear hardware profile packet-drop file_instanceclear hardware profile packet-drop file_instance
Syntax Description
Reset functionsclear
Change hardware usage settingshardware
Profile settingsprofile
Packet Drop parameterspacket-drop
TCB File instancesfile_instance
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)505
C Commandsclear hardware profile packet-drop file_instance
Page 650
clear hardware rate-limiterclear hardware rate-limiter { all | layer-3 { <l3-opts> | multicast <mcast-opts> } | layer-2 <l2-opts> | <opts>| f1 <f1-opts> | span-egress | urpf-fail } [ module <module> ]
Syntax Description
Reset functionsclear
Show hardware informationhardware
Clear Rate-Limiter statisticsrate-limiter
Clear all Rate-Limiter statisticsall
Layer-3 control and Routed packetslayer-3
l3-opts
Multicast data packetsmulticast
mcast-opts
Layer-2 control and Bridged packetslayer-2
l2-opts
opts
Control packets from F1 modules to supervisorf1
f1-opts
SPAN/ERSPAN egress packetsspan-egress
URPF fail packetsurpf-fail
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)506
C Commandsclear hardware rate-limiter
Page 651
clear hardware rate-limiterclear hardware rate-limiter { all | layer-3 { <l3-opts> | multicast <mcast-opts> } | layer-2 <l2-opts> | <opts>| f1 <f1-opts> | span-egress | urpf-fail } [ module <module> ]
Syntax Description
Reset functionsclear
Show hardware informationhardware
Clear Rate-Limiter statisticsrate-limiter
Clear all Rate-Limiter statisticsall
Layer-3 control and Routed packetslayer-3
l3-opts
Multicast data packetsmulticast
mcast-opts
Layer-2 control and Bridged packetslayer-2
l2-opts
opts
Control packets from F1 modules to supervisorf1
f1-opts
SPAN/ERSPAN egress packetsspan-egress
URPF fail packetsurpf-fail
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)507
C Commandsclear hardware rate-limiter
Page 652
clear hsrp counters clear hsrp state-historyclear hsrp counters [ <value> ] | clear hsrp state-history [ interface <interface-id> ] [ group <group-id> ]
Syntax Description
Reset functionsclear
HSRP commandshsrp
Internal counterscounters
(Optional) Counter to be clearedvalue
Clear Groups' state historystate-history
(Optional) Groups on this interfaceinterface
(Optional) Interfaceinterface-id
(Optional) Group numbergroup
(Optional) Group Numbergroup-id
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)508
C Commandsclear hsrp counters clear hsrp state-history
Page 653
clear install all failed-standbyclear install all failed-standby
Syntax Description
Reset functionsclear
Clear the installer loginstall
Clear the install all logall
Clear the failed-standby logfailed-standby
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)509
C Commandsclear install all failed-standby
Page 654
clear install failure-reasonclear install failure-reason
Syntax Description
Reset functionsclear
Clear the installer loginstall
Clear the install failure-reason logfailure-reason
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)510
C Commandsclear install failure-reason
Page 655
clear install log-history allclear install log-history { all | oldest <i0> }
Syntax Description
Reset functionsclear
Install related show commandsinstall
Patch installer historical logslog-history
Delete complete history logall
oldest Delete the oldest <n> install log-history pointsoldest
Number of log-history points to deletei0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)511
C Commandsclear install log-history all
Page 656
clear install statusclear install status
Syntax Description
Reset functionsclear
Clear the installer loginstall
Clear the installer status logstatus
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)512
C Commandsclear install status
Page 657
clear ipclear ip { netstack mroute | mroute data-created } { <all> | <group-prefix> | <group> [ <source> ] } [ vrf {<vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Netstack's local cachenetstack
Clear multicast routing tablemroute
Clear all Data-created PIM ASM (S,G) routesdata-created
Clear all routesall
Clear all routes within the Group prefixgroup-prefix
Clear all sources matching the Groupgroup
(Optional) Clear a (S,G) routesource
(Optional) Clear information for particular VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)513
C Commandsclear ip
Page 658
clear ip adjacency statisticsclear ip adjacency statistics
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear Adjacencyadjacency
Clear Adjacency Statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)514
C Commandsclear ip adjacency statistics
Page 659
clear ip amt tunnelclear ip amt tunnel [ <address4> <port> ] [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
AMT clear commandsclear
AMT show commandsamt
Display IP informationip
Display tunnel informationtunnel
(Optional) Display information for VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) IP address of tunnel endpointaddress4
(Optional) UDP port number of gatewayport
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)515
C Commandsclear ip amt tunnel
Page 660
clear ip arpclear ip arp [ <interface> | <ip-address> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] [ force-delete ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear ARP table and statisticsarp
(Optional) ARP interfaceinterface
(Optional) IP addressip-address
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Clear ARP entries for all vrfsall
(Optional) Clear the entries from ARP table without refreshforce-delete
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)516
C Commandsclear ip arp
Page 661
clear ip arp controller-statisticsclear ip arp controller-statistics
Syntax Description
Reset functionsclear
Display IP informationip
Display ARP table and statisticsarp
Controller statisticscontroller-statistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)517
C Commandsclear ip arp controller-statistics
Page 662
clear ip arp inspection logclear ip arp inspection log
Syntax Description
Reset functionsclear
Clear ip countersip
Clear State of ARP featuresarp
Clear State of ARP Inspectioninspection
Log Bufferlog
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)518
C Commandsclear ip arp inspection log
Page 663
clear ip arp inspection statistics vlanclear ip arp inspection statistics vlan <vlan-id>
Syntax Description
Reset functionsclear
Clear ip countersip
Clear State of ARP featuresarp
Clear State of ARP Inspectioninspection
Statisticsstatistics
Vlan rangevlan
VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19vlan-id
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)519
C Commandsclear ip arp inspection statistics vlan
Page 664
clear ip arp multihoming-statisticsclear ip arp multihoming-statistics [ <interface> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear ARP table and statisticsarp
(Optional) ARP interfaceinterface
Display ARP Multihoming statsmultihoming-statistics
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Clear ARP Multihoming statistics for all vrfsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)520
C Commandsclear ip arp multihoming-statistics
Page 665
clear ip arp statisticsclear ip arp statistics [ <interface> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear ARP table and statisticsarp
(Optional) ARP interfaceinterface
Clear ARP statisticsstatistics
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Clear ARP statistics for all vrfsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)521
C Commandsclear ip arp statistics
Page 666
clear ip arp suppression-cache statisticsclear ip arp suppression-cache statistics
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear ARP table and statisticsarp
ARP-suppression cachesuppression-cache
clear suppression statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)522
C Commandsclear ip arp suppression-cache statistics
Page 667
clear ip arp tunnel-statisticsclear ip arp tunnel-statistics
Syntax Description
Reset functionsclear
Clear IP commandsip
Display ARP table and statisticsarp
Clear ARP statistics for tunneled packetstunnel-statistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)523
C Commandsclear ip arp tunnel-statistics
Page 668
clear ip arp vpc-statisticsclear ip arp vpc-statistics
Syntax Description
Reset functionsclear
Clear IP commandsip
Display ARP table and statisticsarp
Clear ARP vPC statisticsvpc-statistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)524
C Commandsclear ip arp vpc-statistics
Page 669
clear ip dhcp global statisticsclear ip dhcp global statistics
Syntax Description
Reset functionsclear
Clear ip countersip
Clear State of DHCP featuresdhcp
Clear State of DHCP global statsglobal
DHCP snooping statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)525
C Commandsclear ip dhcp global statistics
Page 670
clear ip dhcp relay statisticsclear ip dhcp relay statistics [ interface <intf> | { interface <intf> serverip <ip-addr-val> [ use-vrf <vrf-name>] } ]
Syntax Description
Reset functionsclear
Clear ip countersip
Clear State of DHCP featuresdhcp
Clear State of DHCP relay statsrelay
DHCP Relay statisticsstatistics
(Optional) input interfaceinterface
(Optional) interfaceintf
(Optional) Helper addressserverip
(Optional) IP addressip-addr-val
(Optional) helper address VRF membershipuse-vrf
(Optional) VRF namevrf-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)526
C Commandsclear ip dhcp relay statistics
Page 671
clear ip dhcp snooping bindingclear ip dhcp snooping binding [ { vlan <vlan-id> mac <mac-addr> ip <ip-addr> interface <interface-id> } |
Syntax Description
Reset functionsclear
Clear ip countersip
Clear State of DHCP featuresdhcp
Clear State of DHCP Snoopingsnooping
DHCP snooping bindingsbinding
(Optional) VLANvlan
(Optional) VLAN idvlan-id
(Optional) MAC addressmac
(Optional) MAC addressmac-addr
(Optional) IP addressip
(Optional) IP addressip-addr
(Optional) interfaceinterface
(Optional) interfaceinterface-id
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)527
C Commandsclear ip dhcp snooping binding
Page 672
clear ip dhcp snooping statisticsclear ip dhcp snooping statistics [ { vlan <vlan-id> interface <intf> } |
Syntax Description
Reset functionsclear
Clear ip countersip
Clear State of DHCP featuresdhcp
Clear State of DHCP snooping statssnooping
DHCP snooping statisticsstatistics
(Optional) VLANvlan
(Optional) VLAN idvlan-id
(Optional) input interfaceinterface
(Optional) interfaceintf
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)528
C Commandsclear ip dhcp snooping statistics
Page 673
clear ip eigrp accountingclear { ip | ipv6 } eigrp [ <eigrp-ptag> ] accounting [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IPv6 commandsipv6
EIGRP clear commandseigrp
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
(Optional) Process tageigrp-ptag
Clear IP-EIGRP accounting statisticsaccounting
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)529
C Commandsclear ip eigrp accounting
Page 674
clear ip eigrp event-historyclear { ip | ipv6 } eigrp [ <eigrp-ptag> ] event-history [ fsm | packet | rib | all ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IPv6 commandsipv6
EIGRP clear commandseigrp
(Optional) Process tageigrp-ptag
Clear the event history buffersevent-history
(Optional) FSM log of EIGRPfsm
(Optional) Packet log of EIGRPpacket
(Optional) RIB log of EIGRPrib
(Optional) All event history buffersall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)530
C Commandsclear ip eigrp event-history
Page 675
clear ip eigrp event-history bfdclear { ip | ipv6 } eigrp [ <eigrp-ptag> ] event-history bfd
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IPv6 commandsipv6
EIGRP clear commandseigrp
(Optional) Process tageigrp-ptag
Clear the event history buffersevent-history
Show bfd log of EIGRPbfd
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)531
C Commandsclear ip eigrp event-history bfd
Page 676
clear ip eigrp redistributionclear { ip | ipv6 } eigrp [ <eigrp-ptag> ] redistribution [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IPv6 commandsipv6
EIGRP clear commandseigrp
(Optional) Process tageigrp-ptag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear EIGRP redistributed informationredistribution
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)532
C Commandsclear ip eigrp redistribution
Page 677
clear ip eigrp route-map statistics redistributeclear ip eigrp [ <eigrp-ptag> ] route-map statistics redistribute { bgp <as> | { eigrp | isis | ospf | rip } <tag> |static | direct | amt | lisp } [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
EIGRP clear commandseigrp
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
(Optional) Process tageigrp-ptag
Route-map related informationroute-map
Route-map statisticsstatistics
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv4isis
Open Shortest Path First (OSPF)ospf
Routing Information Protocol (RIP)rip
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Process tagtag
Static routesstatic
Directly connecteddirect
AMT Anycast prefixamt
LISP EID-prefixeslisp
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)533
C Commandsclear ip eigrp route-map statistics redistribute
Page 678
clear ip eigrp trafficclear { ip | ipv6 } eigrp [ <eigrp-ptag> ] traffic [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IPv6 commandsipv6
EIGRP clear commandseigrp
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
(Optional) Process tageigrp-ptag
Clear IP-EIGRP traffic statisticstraffic
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)534
C Commandsclear ip eigrp traffic
Page 679
clear ip igmp event-historyclear ip igmp event-history [ <igmp-event-hist-buf-name> ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IGMP related informationigmp
Clear event-history buffersevent-history
(Optional) Event hist buffer nameigmp-event-hist-buf-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)535
C Commandsclear ip igmp event-history
Page 680
clear ip igmp groupsclear ip igmp { groups | route } { <all> | <group-prefix> | <group> [ <source> ] } [ vrf { <vrf-name> |<vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IGMP related informationigmp
Route informationgroups
Route informationroute
Clear all routesall
Clear all routes within the Group prefixgroup-prefix
Clear all routes matching the Groupgroup
(Optional) Clear a (S,G) routesource
(Optional) Clear information for particular VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)536
C Commandsclear ip igmp groups
Page 681
clear ip igmp interface statisticsclear ip igmp interface statistics [ <interface> ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IGMP statistics informationigmp
Interface related informationinterface
Packet/internal counter statisticsstatistics
(Optional) Specific interface onlyinterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)537
C Commandsclear ip igmp interface statistics
Page 682
clear ip igmp snooping event-historyclear ip igmp snooping event-history [ <igmp-snoop-event-hist-buf-name> ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IGMP Snoopingigmp
Clear IGMP Snoopingsnooping
Clear event history buffersevent-history
(Optional) Event history buffer nameigmp-snoop-event-hist-buf-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)538
C Commandsclear ip igmp snooping event-history
Page 683
clear ip igmp snooping explicit-trackingclear ip igmp snooping explicit-tracking { vlan { <vlan> | all } | bridge-domain { <bdid> | all } }
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IGMP Snoopingigmp
Clear IGMP Snoopingsnooping
Clear Explicit Host tracking informationexplicit-tracking
Clear explicit tracking information for VLANvlan
Specify VLANvlan
Clear explicit tracking information for BDbridge-domain
Specify BDbdid
Clear for all vlans/BDall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)539
C Commandsclear ip igmp snooping explicit-tracking
Page 684
clear ip igmp snooping groupsclear ip igmp snooping groups { <all> | { <group-prefix> | <group> } [ <source> ] } [ interface <if-name> ]{ vlan { <vlan> | all } | bridge-domain { <bdid> | all } }
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IGMP Snoopingigmp
Clear IGMP Snoopingsnooping
Clear snooped groupsgroups
Clear all groupsall
Group prefix to cleargroup-prefix
Group address to cleargroup
(Optional) Source address to clearsource
(Optional) Specify interface to clear group stateinterface
(Optional) Interface name to clearif-name
Clear information for VLANvlan
Specify the VLAN numbervlan
Clear information for BDbridge-domain
Specify the BD numberbdid
Clear for all VLAN/BDsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)540
C Commandsclear ip igmp snooping groups
Page 685
clear ip igmp snooping proxy querier ports vlanclear ip igmp snooping proxy querier ports { vlan <vlan> | bridge-domain <bdid> } <if-name> [ purge ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IGMP Snoopingigmp
Clear IGMP Snoopingsnooping
Clear IGMP snooping proxyproxy
Clear IGMP snooping proxy querierquerier
Clear IGMP snooping proxy querier portsports
Clear for a specific vlanvlan
Specify the VLAN numbervlan
Clear for a specific BDbridge-domain
Specify the BD numberbdid
Interface name to clearif-name
(Optional) Remove port from priority listpurge
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)541
C Commandsclear ip igmp snooping proxy querier ports vlan
Page 686
clear ip igmp snooping report statisticsclear ip igmp snooping { report-policy | access-group } statistics [ vlan <vlan> ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IGMP Snoopingigmp
Clear IGMP Snoopingsnooping
IGMP Report Policyreport-policy
IGMP access-groupaccess-group
Policy statisticsstatistics
(Optional) Clear VLAN IGMP snooping policy statistics informationvlan
(Optional) Specify VLANvlan
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)542
C Commandsclear ip igmp snooping report statistics
Page 687
clear ip igmp snooping statisticsclear ip igmp snooping statistics { vlan <vlan> | bridge-domain <bdid> | all }
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IGMP Snoopingigmp
Clear IGMP Snoopingsnooping
Packet/internal counter statisticsstatistics
Clear VLAN statisticsvlan
Specify VLANvlan
Clear BD statisticsbridge-domain
Specify BDbdid
All VLAN/BDsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)543
C Commandsclear ip igmp snooping statistics
Page 688
clear ip interface statisticsclear ip interface statistics [ <interface> ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IP related interface informationinterface
Clear IP interface statisticsstatistics
(Optional) Clear IP statistics for interfaceinterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)544
C Commandsclear ip interface statistics
Page 689
clear ip lisp data-cacheclear ip lisp data-cache [ <eid> ] [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
LISP clear commandslisp
Clear EID-to-RLOC data cache mapping in this ITRdata-cache
(Optional) Clear mapping for IP destination EIDeid
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)545
C Commandsclear ip lisp data-cache
Page 690
clear ip lisp map-cache{ { clear ip lisp map-cache [ <eid-prefix> ] [ vrf { <vrf-name> | <vrf-known-name> } ] } | { clear ipv6 lispmap-cache [ <eid-prefix6> ] [ vrf { <vrf-name> | <vrf-known-name> } ] } }
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IPv6 commandsipv6
LISP clear commandslisp
Clear an EID-to-RLOC cache mapping in this ITRmap-cache
(Optional) Clear entry for particular vrfvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Clear entry associated with IP EID-prefixeid-prefix
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)546
C Commandsclear ip lisp map-cache
Page 691
clear ip lisp statisticsclear ip lisp statistics [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
LISP clear commandslisp
Clear global LISP statisticsstatistics
(Optional) Clear statistics for vrfvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)547
C Commandsclear ip lisp statistics
Page 692
clear ip mbgp dampening{ { clear ip mbgp [ vrf { <vrf-name> | <vrf-known-name> | ALL_VRFS_012345678901234 } ] dampening[ <ip-prefix> | <ip-addr> [ <ip-mask> ] ] } | { clear ip bgp [ vrf { <vrf-name> | <vrf-known-name> |ALL_VRFS_012345678901234 } ] dampening [ <ip-prefix> | <ip-addr> [ <ip-mask> ] ] } | { clear ip bgp [vrf { <vrf-name> | <vrf-known-name> | ALL_VRFS_012345678901234 } ] ipv4 { unicast | multicast }dampening [ <ip-prefix> | <ip-addr> [ <ip-mask> ] ] } | { clear ip bgp [ vrf { <vrf-name> | <vrf-known-name>| ALL_VRFS_012345678901234 } ] all dampening } | { clear bgp [ vrf { <vrf-name> | <vrf-known-name> |ALL_VRFS_012345678901234 } ] { ipv4 { unicast | multicast } | vpnv4 unicast } dampening [ <ip-prefix>| <ip-addr> [ <ip-mask> ] ] } | { clear bgp [ vrf { <vrf-name> | <vrf-known-name> |ALL_VRFS_012345678901234 } ] { ipv6 { unicast | multicast } | vpnv6 unicast } dampening [ <ipv6-prefix>] } | { clear bgp [ vrf { <vrf-name> | <vrf-known-name> | ALL_VRFS_012345678901234 } ] all dampening} } [ vrf { <vrf-name> | <vrf-known-name> | ALL_VRFS_012345678901234 } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
(Optional) Virtual Router Contextvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Clear BGP sessionsbgp
Clear MBGP sessionsmbgp
Clear route flap dampening informationdampening
(Optional) Clear route flap dampening for prefixip-prefix
(Optional) Clear route flap dampening for one networkip-addr
(Optional) Network maskip-mask
Clear IPv4 address-familyipv4
Clear IPv6 address-familyipv6
Clear VPNv4 address-familyvpnv4
Clear VPNv6 address-familyvpnv6
Clear unicast address-familyunicast
Clear multicast address-familymulticast
Clear all address-familiesall
Command Mode
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)548
C Commandsclear ip mbgp dampening
Page 693
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)549
C Commandsclear ip mbgp dampening
Page 694
clear ip mbgp flap-statistics{ { clear ip mbgp [ vrf { <vrf-name> | <vrf-known-name> | ALL_VRFS_012345678901234 } ] flap-statistics[ <ip-prefix> | <ip-addr> [ <ip-mask> ] ] } | { clear ip bgp [ vrf { <vrf-name> | <vrf-known-name> |ALL_VRFS_012345678901234 } ] flap-statistics [ <ip-prefix> | <ip-addr> [ <ip-mask> ] ] } | { clear ip bgp[ vrf { <vrf-name> | <vrf-known-name> | ALL_VRFS_012345678901234 } ] ipv4 { unicast | multicast }flap-statistics [ <ip-prefix> | <ip-addr> [ <ip-mask> ] ] } | { clear ip bgp [ vrf { <vrf-name> | <vrf-known-name>| ALL_VRFS_012345678901234 } ] all flap-statistics } | { clear bgp [ vrf { <vrf-name> | <vrf-known-name>| ALL_VRFS_012345678901234 } ] { ipv4 { unicast | multicast } | vpnv4 unicast } flap-statistics [ <ip-prefix>| <ip-addr> [ <ip-mask> ] | regexp <regexp-str> ] } | { clear bgp [ vrf { <vrf-name> | <vrf-known-name> |ALL_VRFS_012345678901234 } ] { ipv6 { unicast | multicast } | vpnv6 unicast } flap-statistics [ <ipv6-prefix>| regexp <regexp-str> ] } | { clear bgp [ vrf { <vrf-name> | <vrf-known-name> | ALL_VRFS_012345678901234} ] all flap-statistics } } [ vrf { <vrf-name> | <vrf-known-name> | ALL_VRFS_012345678901234 } ]
Syntax Description
Reset functionsclear
(Optional) Virtual Router Contextvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Clear IP commandsip
Clear BGP sessionsbgp
Clear MBGP sessionsmbgp
Clear flap statisticsflap-statistics
(Optional) Clear flap statistics for one prefixip-prefix
(Optional) Clear flap statistics for one networkip-addr
(Optional) Network maskip-mask
Clear IPv4 address-familyipv4
Clear IPv6 address-familyipv6
Clear VPNv4 address-familyvpnv4
Clear VPNv6 address-familyvpnv6
Clear unicast address-familyunicast
Clear multicast address-familymulticast
Clear all address-familiesall
(Optional) Clear flap statistics for routes matching the regular expressionregexp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)550
C Commandsclear ip mbgp flap-statistics
Page 695
(Optional) Regular expression to match the AS pathsregexp-str
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)551
C Commandsclear ip mbgp flap-statistics
Page 696
clear ip mbgp peer-template{ { clear ipmbgp [ vrf { <vrf-name> | <vrf-known-name> | ALL_VRFS_012345678901234 } ] { <neighbor-id>| * | <asn> | <prefix-id> peer-template <peer-template-name> } [ soft [ in | out ] | dampened-paths | flap-statistics| no-notify ] } | { clear ip bgp [ vrf { <vrf-name> | <vrf-known-name> | ALL_VRFS_012345678901234 } ]{ <neighbor-id> | * | <asn> | <prefix-id> | peer-template <peer-template-name> } [ soft [ in | out ] |dampened-paths | flap-statistics | no-notify | { ipv4 { unicast | multicast } | { vpnv4 | vpnv6 } unicast | all } {soft [ in | out ] | dampened-paths | flap-statistics | no-notify } ] } | { clear bgp [ vrf { <vrf-name> |<vrf-known-name> | ALL_VRFS_012345678901234 } ] { ipv4 { unicast | multicast | mvpn | labeled-unicast} | ipv6 { unicast | multicast | mvpn | labeled-unicast } | { vpnv4 | vpnv6 } unicast | l2vpn vpls | l2vpn evpn |link-state | all } { <neighbor-id> | <ipv6-neighbor-id> | * | <asn> | peer-template <peer-template-name> |<prefix-id> | <ipv6-prefix-id> } [ soft [ in | out ] | dampened-paths | flap-statistics | no-notify ] } } [ vrf {<vrf-name> | <vrf-known-name> | ALL_VRFS_012345678901234 } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
(Optional) Virtual Router Contextvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Clear BGP sessionsbgp
Clear MBGP sessionsmbgp
IP address of the neighbor to clearneighbor-id
Clear all neighbors matching the prefixprefix-id
Clear all neighbors (Should be a * character)*
Clear all neighbors in an ASasn
Clear all neighbors in a peer-templatepeer-template
Peer-template namepeer-template-name
(Optional) Soft reconfigurationsoft
(Optional) Clear soft reconfiguration inboundin
(Optional) Clear soft reconfiguration outboundout
(Optional) Clear IPv4 address-familyipv4
Clear IPv6 address-familyipv6
(Optional) Clear VPNv4 address-familyvpnv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)552
C Commandsclear ip mbgp peer-template
Page 697
(Optional) Clear VPNv6 address-familyvpnv6
(Optional) Clear unicast address-familyunicast
(Optional) Clear multicast address-familymulticast
Clear link-state address-familylink-state
Display BGP information for L2VPN address familyl2vpn
Display BGP information for L2VPN VPLS address familyvpls
Display BGP information for MVPN address familymvpn
Display BGP information for L2VPN EVPN address familyevpn
Display BGP information for labeled-unicast address familylabeled-unicast
(Optional) Clear all address-familiesall
(Optional) Clear dampened paths for neighbordampened-paths
(Optional) Clear flap statistics for neighborflap-statistics
(Optional) Clear without sending notificationno-notify
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)553
C Commandsclear ip mbgp peer-template
Page 698
clear ip mfwd event-historyclear ip mfwd event-history [ <mfwd-event-hist-buf-name> ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear MCASTFWD related informationmfwd
Clear event-history buffersevent-history
(Optional) Event hist buffer namemfwd-event-hist-buf-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)554
C Commandsclear ip mfwd event-history
Page 699
clear ip mrouteclear ip mroute [ repopulate ] { { <all> [ shared-tree | source-tree ] } | { <group-prefix> [ shared-tree | source-tree] } | { <group> [ <source> | shared-tree | source-tree ] } } [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear multicast routing tablemroute
(Optional) ClearMRIB states and request other components to repopulatemroutes
repopulate
Clear all routesall
Clear all routes within the Group prefixgroup-prefix
Clear all routes matching the Groupgroup
(Optional) Clear a (S,G) routesource
(Optional) Clear the (*,G) route associated with the groupshared-tree
(Optional) Clear all (S,G) routes associated with the groupsource-tree
(Optional) Clear information for particular VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)555
C Commandsclear ip mroute
Page 700
clear ip mroute statisticsclear ip mroute statistics { <all> | <group-prefix> | <group> [ <source> ] } [ vrf { <vrf-name> |<vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear multicast routing tablemroute
Clear statistics of multicast routestatistics
Clear all routesall
Clear all routes within the Group prefixgroup-prefix
Clear all routes matching the Groupgroup
(Optional) Clear a (S,G) routesource
(Optional) Clear information for particular VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)556
C Commandsclear ip mroute statistics
Page 701
clear ip msdp event-historyclear ip msdp event-history [ <msdp-event-hist-buf-name> ]
Syntax Description
Reset functionsclear
Clear IP commandsip
MSDP global configuration commandsmsdp
Clear the event-history buffer instancesevent-history
(Optional) Specify the particular instance of the event-history buffermsdp-event-hist-buf-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)557
C Commandsclear ip msdp event-history
Page 702
clear ip msdp peerclear ip msdp peer <peer-address> [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
MSDP clear commandsmsdp
Clear MSDP peer connectionpeer
IP address of MSDP peerpeer-address
(Optional) Clear information for particular VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)558
C Commandsclear ip msdp peer
Page 703
clear ip msdp policy statistics sa-policy inclear ip msdp policy statistics sa-policy <peer-address> { in | out } [ vrf { <vrf-name> | <vrf-known-name>} ]
Syntax Description
Reset functionsclear
Clear IP commandsip
MSDP global configuration commandsmsdp
Policy informationpolicy
Policy statisticsstatistics
Configureed SA policy for MSDP peersa-policy
IP address of MSDP peer for SA policypeer-address
Input policyin
Output policyout
(Optional) Clear information for particular VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)559
C Commandsclear ip msdp policy statistics sa-policy in
Page 704
clear ip msdp saclear ip msdp { sa-cache | route } { <all> | <group-prefix> | <group> [ <source> ] } [ vrf { <vrf-name> |<vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
MSDP clear commandsmsdp
Clear contents of SA cachesa-cache
Clear contents of SA cacheroute
Clear all routesall
Clear all routes within the Group prefixgroup-prefix
Clear all routes matching the Groupgroup
(Optional) Clear a (S,G) routesource
(Optional) Clear information for particular VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)560
C Commandsclear ip msdp sa
Page 705
clear ip msdp statisticsclear ip msdp statistics [ <peer-address> ] [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
MSDP clear commandsmsdp
Clear statistics for peersstatistics
(Optional) IP address of MSDP peerpeer-address
(Optional) Clear information for particular VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)561
C Commandsclear ip msdp statistics
Page 706
clear ip nat-alias addressclear ip nat-alias { address <ipaddress> | all }
Syntax Description
Reset functionsclear
Clear ip countersip
Clear NAT aliasnat-alias
alias addressaddress
NAT alias ip addressipaddress
Delete all NAT alias addressall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)562
C Commandsclear ip nat-alias address
Page 707
clear ip nat statisticsclear ip nat statistics
Syntax Description
Reset functionsclear
Clear ip countersip
IP NAT informationnat
Translation statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)563
C Commandsclear ip nat statistics
Page 708
clear ip nat translationclear ip nat translation { entry-id <xlation_id> | all | inside <insideGlobalIP> <insideLocalIP> [ outside<outsideLocalIP> <outsideGlobalIP> ] | outside <outsideLocalIP> <outsideGlobalIP> | tcp { inside<insideGlobalIP> <insideGlobal-port> <insideLocalIP> <insideLocal-port> outside <outsideLocalIP><outsideLocal-port> <outsideGlobalIP> <outsideGlobal-port> } | udp { inside <insideGlobalIP><insideGlobal-port> <insideLocalIP> <insideLocal-port> outside <outsideLocalIP> <outsideLocal-port><outsideGlobalIP> <outsideGlobal-port> } | icmp { inside <insideGlobalIP> <insideGlobal-port><insideLocalIP> <insideLocal-port> outside <outsideLocalIP> <outsideLocal-port> <outsideGlobalIP><outsideGlobal-port> } }
Syntax Description
Reset functionsclear
Clear ip countersip
Clear NATnat
Clear dynamic translationtranslation
Dynamic xlation identry-id
Dynamic xlation idxlation_id
Delete all dynamic translationsall
Inside addressesinside
Inside global IP addressinsideGlobalIP
Inside local IP addressinsideLocalIP
(Optional) Outside addressesoutside
(Optional) Outside local IP addressoutsideLocalIP
(Optional) Outside global IP addressoutsideGlobalIP
Transmission Control Protocoltcp
User Datagram Protocoludp
Internet Control Message Protocolicmp
Inside global TCP/UDP/ICMP port addressinsideGlobal-port
Inside local TCP/UDP/ICMP port addressinsideLocal-port
Outside local TCP/UDP port/ICMP addressoutsideLocal-port
Outside global TCP/UDP/ICMP port addressoutsideGlobal-port
Command Mode
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)564
C Commandsclear ip nat translation
Page 709
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)565
C Commandsclear ip nat translation
Page 710
clear ip ospf databaseclear ip ospf [ <tag> ] database
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear OSPF tablesospf
(Optional) Process tagtag
Clear the LSDB and all neighborsdatabase
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)566
C Commandsclear ip ospf database
Page 711
clear ip ospf event-historyclear ip ospf [ <tag> ] event-history [ adjacency | event | ha | flooding | lsa | spf | redistribution | cli | ldp | te |rib | hello | spf-trigger | objstore | all ]
Syntax Description
Reset functionsclear
IP eventsip
Debug OSPF eventsospf
(Optional) Process tagtag
Clear the event history buffersevent-history
(Optional) Adjacency formation logsadjacency
(Optional) Internal event logsevent
(Optional) HA and GR logsha
(Optional) LSA flooding logsflooding
(Optional) LSA generation and database logslsa
(Optional) SPF calculation logsspf
(Optional) Redistribution logsredistribution
(Optional) Cli logscli
(Optional) LDP related logsldp
(Optional) MPLS TE related logste
(Optional) RIB related logsrib
(Optional) HELLO related logshello
(Optional) SPF TRIGGER related logsspf-trigger
(Optional) DME OBJSTORE related logsobjstore
(Optional) All event history buffersall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)567
C Commandsclear ip ospf event-history
Page 712
clear ip ospf interfaceclear ip ospf [ <tag> ] interface { * | <interface> }
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear OSPF tablesospf
(Optional) Process tagtag
Clear one or more interfacesinterface
Clear all interfaces*
Interface to clearinterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)568
C Commandsclear ip ospf interface
Page 713
clear ip ospf neighborclear ip ospf [ <tag> ] neighbor { { { * | <neighborid> } [ vrf { <vrf-name> | <vrf-known-name> | all } ] } |{ <interface> } }
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear OSPF tablesospf
(Optional) Process tagtag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear one or more neighborsneighbor
Clear all neighbors*
Source IP address, or router ID of the neighborneighborid
Interface to clear all neighbors oninterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)569
C Commandsclear ip ospf neighbor
Page 714
clear ip ospf policy statisticsclear ip ospf [ <tag> ] policy statistics { { redistribute { bgp <as> | { eigrp | isis | ospf | rip } <tag> | static |direct | amt | lisp } } | { area <area-id-ip> filter-list { in | out } } } [ vrf { <vrf-name> | <vrf-known-name> |all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear OSPF tablesospf
(Optional) Process tagtag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear Policy related informationpolicy
Display Route Filter statisticsstatistics
Statistics for redistributionredistribute
ISO Intermediate-to-Intermediate (IS-IS)isis
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
Open Shortest Path First (OSPFv2)ospf
Enhanced Interior Gateway Protocol (EIGRP)eigrp
Routing Information Protocol (RIP)rip
Staticstatic
Directly connecteddirect
AMT anycast prefixamt
LISP EID-prefixeslisp
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Filter prefixes between OSPF areasfilter-list
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)570
C Commandsclear ip ospf policy statistics
Page 715
Filter networks sent to this areain
Filter networks sent from this areaout
tag
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)571
C Commandsclear ip ospf policy statistics
Page 716
clear ip ospf redistributionclear ip ospf [ <tag> ] redistribution [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear OSPF tablesospf
(Optional) Process tagtag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear OSPF route redistributionredistribution
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)572
C Commandsclear ip ospf redistribution
Page 717
clear ip ospf statisticsclear ip ospf [ <tag> ] statistics [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear OSPF tablesospf
(Optional) Process tagtag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear event countersstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)573
C Commandsclear ip ospf statistics
Page 718
clear ip ospf trafficclear ip ospf [ <tag> ] traffic [ <interface> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear OSPF tablesospf
(Optional) Process tagtag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear packet counterstraffic
(Optional) Interface to clear all traffic oninterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)574
C Commandsclear ip ospf traffic
Page 719
clear ip pim event-historyclear ip pim event-history [ <pim-event-hist-buf-name> ]
Syntax Description
Reset functionsclear
Clear IP commandsip
PIM clear commandspim
Clear event history buffersevent-history
(Optional) Event history buffer instancepim-event-hist-buf-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)575
C Commandsclear ip pim event-history
Page 720
clear ip pim interface statisticsclear ip pim interface statistics [ <interface> | vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear PIM informationpim
Interface related informationinterface
Packet interface counter statisticsstatistics
(Optional) Interface name to clearinterface
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)576
C Commandsclear ip pim interface statistics
Page 721
clear ip pim policy statisticsclear ip pim policy statistics { register-policy | bsr { bsr-policy | rp-candidate-policy } | auto-rp {rp-candidate-policy | mapping-agent-policy } } [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
PIM global configuration commandspim
Policy related informationpolicy
Policy statisticsstatistics
Show statistics for register-policyregister-policy
Bootstrap protocol RP-distribution policybsr
Statistics for BSR messagesbsr-policy
Statistics for RP candidate messagesrp-candidate-policy
Statistics for auto-rp messagesauto-rp
Statistics for RP candidate messagesrp-candidate-policy
Statistics for mapping agent messagesmapping-agent-policy
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)577
C Commandsclear ip pim policy statistics
Page 722
clear ip pim policy statistics jpclear ip pim policy statistics { jp-policy | neighbor-policy } <interface>
Syntax Description
Reset functionsclear
Clear IP commandsip
PIM global configuration commandspim
Policy related informationpolicy
Policy statisticsstatistics
Statistics for jp-policyjp-policy
Statistics for neighbor-policyneighbor-policy
Interfaceinterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)578
C Commandsclear ip pim policy statistics jp
Page 723
clear ip pim routeclear ip pim route { <all> | <group-prefix> | <group> [ <source> ] } [ vrf { <vrf-name> | <vrf-known-name>| all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
PIM clear commandspim
Route informationroute
Clear all routesall
Clear all routes within the Group prefixgroup-prefix
Clear all routes matching the Groupgroup
(Optional) Clear a (S,G) routesource
(Optional) Clear information for particular VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)579
C Commandsclear ip pim route
Page 724
clear ip pim statisticsclear ip pim statistics [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear PIM informationpim
Packet global counter statisticsstatistics
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)580
C Commandsclear ip pim statistics
Page 725
clear ip rip policy statistics redistribute bgp{ { clear ip rip policy statistics redistribute bgp <as> } | { clear ip rip policy statistics redistribute eigrp <tag>} | { clear ip rip policy statistics redistribute isis <tag> } | { clear ip rip policy statistics redistribute rip <tag>} | { clear ip rip policy statistics redistribute ospf <tag> } | { clear ip rip policy statistics redistribute direct }| { clear ip rip policy statistics redistribute static } } [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Routing Information Protocol (RIP)rip
Policy related informationpolicy
Policy statisticsstatistics
RIP redistribute routes from other routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Autonomous system numberas
Intermediate-to-intermediate (ISIS)isis
Open Shortest Path First (OSPFv2)ospf
Process tagtag
Static routesstatic
Directly connected routesdirect
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)581
C Commandsclear ip rip policy statistics redistribute bgp
Page 726
clear ip rip statisticsclear { ipv6 | ip } rip statistics [ * | <interface> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
Clear IP commandsip
Routing Information Protocol (RIP)rip
Clear RIP statisticsstatistics
(Optional) RIP statistics for all interfaces*
(Optional) RIP interfaceinterface
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)582
C Commandsclear ip rip statistics
Page 727
clear ip routing multicast event-historyclear ip routing multicast event-history [ <mrib-event-hist-buf-name> ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear event-history buffersrouting
Clear all multicast event-history buffersmulticast
Clear event history buffersevent-history
(Optional) Event history buffermrib-event-hist-buf-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)583
C Commandsclear ip routing multicast event-history
Page 728
clear ip trafficclear ip traffic [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
Reset functionsclear
Clear IP commandsip
Clear IP global statisticstraffic
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)584
C Commandsclear ip traffic
Page 729
clear ipv6 adjacency statisticsclear ipv6 adjacency statistics
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
Clear Adjacencyadjacency
Clear Adjacency Statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)585
C Commandsclear ipv6 adjacency statistics
Page 730
clear ipv6 amt tunnelclear ipv6 amt tunnel [ <address6> <port> ] [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
AMT clear commandsclear
AMT show commandsamt
Display IP informationipv6
Display tunnel informationtunnel
(Optional) Display information for VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) UDP port number of gatewayport
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)586
C Commandsclear ipv6 amt tunnel
Page 731
clear ipv6 dhcp-ldra statisticsclear ipv6 dhcp-ldra statistics
Syntax Description
Reset functionsclear
IPv6ipv6
Clear State of DHCPv6 LDRA statsdhcp-ldra
DHCPv6 LDRA statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)587
C Commandsclear ipv6 dhcp-ldra statistics
Page 732
clear ipv6 dhcp relay statisticsclear ipv6 dhcp relay statistics [ interface <intf> [ [ server-ip <ip-addr-val> [ use-vrf <vrf-name> ] [ interface<dest-interface> ] ] | [ server-ip <ip-addr-val> [ interface <dest-interface> ] [ use-vrf <vrf-name> ] ] ] ]
Syntax Description
Reset functionsclear
IPv6ipv6
Clear State of DHCPv6 featuresdhcp
Clear State of DHCPv6 relay statsrelay
DHCPv6 Relay statisticsstatistics
(Optional) input interfaceinterface
(Optional) interfaceintf
(Optional) Server addressserver-ip
(Optional) Server address VRF membershipuse-vrf
(Optional) VRF namevrf-name
(Optional) Destination interface for the server addressinterface
(Optional) Destination interfacedest-interface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)588
C Commandsclear ipv6 dhcp relay statistics
Page 733
clear ipv6 eigrp route-map statistics redistributeclear ipv6 eigrp [ <eigrp-ptag> ] route-map statistics redistribute { bgp <as> | { eigrp | isis | ospfv3 | rip }<tag> | static | direct | amt | lisp } [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
EIGRP clear commandseigrp
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
(Optional) Process tageigrp-ptag
Route-map related informationroute-map
Route-map statisticsstatistics
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv4isis
Open Shortest Path First (OSPF) V3ospfv3
Routing Information Protocol (RIP)rip
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Process tagtag
Static routesstatic
Directly connecteddirect
AMT Anycast prefixamt
LISP EID-prefixeslisp
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)589
C Commandsclear ipv6 eigrp route-map statistics redistribute
Page 734
clear ipv6 icmpclear ipv6 { icmp | nd } { interface statistics [ <interface> ] | global statistics }
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
Clear ICMPv6 informationicmp
Clear Neighbor Discovery interface informationnd
Clear ICMPv6 related interface informationinterface
Clear ICMPv6 interface statisticsstatistics
Clear ICMPv6 global statisticsglobal
(Optional) Interface to clear statistics forinterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)590
C Commandsclear ipv6 icmp
Page 735
clear ipv6 icmp vpc-statisticsclear ipv6 icmp vpc-statistics
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
Clear ICMPv6 informationicmp
Clear ICMPv6 ND vPC statisticsvpc-statistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)591
C Commandsclear ipv6 icmp vpc-statistics
Page 736
clear ipv6 interface statisticsclear ipv6 interface statistics [ <interface> ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
Clear IPv6 related interface informationinterface
Clear IPv6 interface statisticsstatistics
(Optional) Interface to clear statistics forinterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)592
C Commandsclear ipv6 interface statistics
Page 737
clear ipv6 lisp data-cacheclear ipv6 lisp data-cache [ <eid6> ] [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
LISP clear commandslisp
Clear EID-to-RLOC data cache mapping in this ITRdata-cache
(Optional) Clear mapping for IPv6 destination EIDeid6
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)593
C Commandsclear ipv6 lisp data-cache
Page 738
clear ipv6 lisp statisticsclear ipv6 lisp statistics [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
LISP clear commandslisp
Clear global LISP statisticsstatistics
(Optional) Clear statistics for vrfvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)594
C Commandsclear ipv6 lisp statistics
Page 739
clear ipv6 mld groupsclear ipv6 [ icmp ] mld { groups | route } { <all> | <group-prefix> | <group> [ <source> ] } [ vrf { <vrf-name>| <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
(Optional) Clear ICMPv6 informationicmp
Clear Multicast Listener Discovery informationmld
Route informationgroups
Route informationroute
Clear all routesall
(Optional) Clear information for particular VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)595
C Commandsclear ipv6 mld groups
Page 740
clear ipv6 mrouteclear ipv6 mroute { { <all> [ shared-tree | source-tree ] } | { <group-prefix> [ shared-tree | source-tree ] } | {<group> [ <source> | shared-tree | source-tree ] } } [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
Clear multicast routing tablemroute
Clear all routesall
(Optional) Clear the (*,G) route associated with the groupshared-tree
(Optional) Clear all (S,G) routes associated with the groupsource-tree
(Optional) Clear information for particular VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)596
C Commandsclear ipv6 mroute
Page 741
clear ipv6 neighborclear ipv6 neighbor [ [ <nbr-addr> [ <intf> ] ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] | vrf { <vrf-name>| <vrf-known-name> | all } | <interface> ] [ force-delete ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
Clear ICMPv6 neighbor cacheneighbor
(Optional) Clear cache entries for given interfaceintf
(Optional) Clear cache entries for given interfaceinterface
(Optional) Clear the cache entries without refreshforce-delete
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)597
C Commandsclear ipv6 neighbor
Page 742
clear ipv6 neighbor bindingclear ipv6 neighbor binding [ mac <macaddr> | address { <ipv6-addr> | all } | policy <policy-name> |
Syntax Description
Reset functionsclear
IPv6ipv6
(Optional) 48-bit hardware addressmacaddr
(Optional) Snooping Policy name to be clearedpolicy-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)598
C Commandsclear ipv6 neighbor binding
Page 743
clear ipv6 pim event-historyclear ipv6 pim event-history [ <pim6-event-hist-buf-name> ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
Clear PIM event history bufferspim
Clear event-history buffersevent-history
(Optional) Event-history buffer instancepim6-event-hist-buf-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)599
C Commandsclear ipv6 pim event-history
Page 744
clear ipv6 pim interface statisticsclear ipv6 pim interface statistics [ <interface> ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
Clear PIM6 informationpim
Interface related informationinterface
Packet interface counter statisticsstatistics
(Optional) Interface name to clearinterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)600
C Commandsclear ipv6 pim interface statistics
Page 745
clear ipv6 pim policy statistics jpclear ipv6 pim policy statistics { jp-policy | neighbor-policy } <interface>
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
Clear PIM informationpim
Policy related informationpolicy
Policy statisticsstatistics
Statistics for jp-policyjp-policy
Statistics for neighbor-policyneighbor-policy
Interfaceinterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)601
C Commandsclear ipv6 pim policy statistics jp
Page 746
clear ipv6 pim routeclear ipv6 pim route { <all> | <group-prefix> | <group> [ <source> ] } [ vrf { <vrf-name> | <vrf-known-name>| all } ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
PIM6 clear commandspim
Route informationroute
Clear all routesall
(Optional) Clear information for particular VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)602
C Commandsclear ipv6 pim route
Page 747
clear ipv6 pim statisticsclear ipv6 pim statistics [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
Clear PIM6 informationpim
Packet global counter statisticsstatistics
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)603
C Commandsclear ipv6 pim statistics
Page 748
clear ipv6 raguard statisticsclear ipv6 raguard statistics
Syntax Description
Reset functionsclear
IPv6ipv6
IPV6 raguardraguard
RA packet drop countstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)604
C Commandsclear ipv6 raguard statistics
Page 749
clear ipv6 rip policy statistics redistribute bgp{ { clear ipv6 rip policy statistics redistribute bgp <as> } | { clear ipv6 rip policy statistics redistribute eigrp<tag> } | { clear ipv6 rip policy statistics redistribute isis <tag> } | { clear ipv6 rip policy statistics redistributerip <tag> } | { clear ipv6 rip policy statistics redistribute ospfv3 <tag> } | { clear ipv6 rip policy statisticsredistribute direct } | { clear ipv6 rip policy statistics redistribute static } } [ vrf { <vrf-name> |<vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
Routing Information Protocol (RIP)rip
Policy related informationpolicy
Policy statisticsstatistics
RIP redistribute routes from other routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Intermediate-to-intermediate (ISIS)isis
Open Shortest Path First (OSPFv3)ospfv3
Process tagtag
Static routesstatic
Directly connected routesdirect
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)605
C Commandsclear ipv6 rip policy statistics redistribute bgp
Page 750
clear ipv6 routing multicast event-historyclear ipv6 routing multicast event-history [ <m6rib-event-hist-buf-name> ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
Clear event-history buffersrouting
Clear all multicast event-history buffersmulticast
Clear event-history buffersevent-history
(Optional) Event-history buffer namem6rib-event-hist-buf-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)606
C Commandsclear ipv6 routing multicast event-history
Page 751
clear ipv6 snooping countersclear ipv6 snooping counters [ { interface <intf> | vlan <vlanid> } ]
Syntax Description
Reset functionsclear
IPv6ipv6
(Optional) interfaceintf
(Optional) VLAN IDvlanid
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)607
C Commandsclear ipv6 snooping counters
Page 752
clear ipv6 snooping eventsclear ipv6 snooping events
Syntax Description
Reset functionsclear
IPv6ipv6
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)608
C Commandsclear ipv6 snooping events
Page 753
clear ipv6 snooping messagesclear ipv6 snooping messages
Syntax Description
Reset functionsclear
IPv6ipv6
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)609
C Commandsclear ipv6 snooping messages
Page 754
clear ipv6 trafficclear ipv6 traffic [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
Reset functionsclear
Clear IPv6 commandsipv6
Clear IPv6 traffic statisticstraffic
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)610
C Commandsclear ipv6 traffic
Page 755
clear isis adjacencyclear isis [ <isis-tag> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] adjacency { * | { <interface> | system-id<sid> } + } [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IS-IS informationisis
(Optional) Routing process tagisis-tag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear IS-IS adjacency stateadjacency
IS-IS adjacencies on all interfaces*
IS-IS interfaceinterface
Hostname or System IDsystem-id
Hostname or System ID (in the form of XXXX.XXXX.XXXX)sid
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)611
C Commandsclear isis adjacency
Page 756
clear isis dpiclear isis [ <isis-tag> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] dpi [ vrf { <vrf-name> |<vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IS-IS informationisis
(Optional) Routing process tagisis-tag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear IS-IS DPI logsdpi
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)612
C Commandsclear isis dpi
Page 757
clear isis event-historyclear isis [ <isis-tag> ] event-history [ <isis-event-hist-buf-name> ]
Syntax Description
Reset functionsclear
Clear IS-IS informationisis
(Optional) Routing process tagisis-tag
Clear event history buffersevent-history
(Optional) Clear the specific event history bufferisis-event-hist-buf-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)613
C Commandsclear isis event-history
Page 758
clear isis ipv6 route-map statisticsclear isis [ <isis-tag> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] ipv6 route-map statistics { { redistribute{ bgp <as> | { <src-isis> | eigrp | ospfv3 | rip } <tag> } } | { redistribute { static | direct | amt } } | { distribute<src-level> into <dst-level> } } [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IS-IS informationisis
(Optional) Routing process tagisis-tag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear IS-IS IPv6 informationipv6
Clear IS-IS route-map statisticsstatistics
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Enhanced Interior Gateway Protocoleigrp
Autonomous system numberas
IS-IS Routing for IPv6src-isis
Open Shortest Path First (OSPF) V3ospfv3
RIP for IPv6 (RIPNG)rip
Process tagtag
Static routesstatic
Directly connecteddirect
AMT anycast prefixamt
Route-map to constrain redistributionroute-map
Distribute routes between ISIS levelsdistribute
from level-n into level-minto
Route-distribution between levelssrc-level
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)614
C Commandsclear isis ipv6 route-map statistics
Page 759
Route-distribution between levelsdst-level
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)615
C Commandsclear isis ipv6 route-map statistics
Page 760
clear isis redistributionclear isis [ <isis-tag> ] redistribution [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IS-IS informationisis
(Optional) Routing process tagisis-tag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear IS-IS redistributed informationredistribution
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)616
C Commandsclear isis redistribution
Page 761
clear isis route-map statisticsclear isis [ <isis-tag> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] [ ip ] route-map statistics { { redistribute{ bgp <as> | { <src-isis> | eigrp | ospf | rip } <tag> } } | { redistribute { static | direct | amt } } | { distribute<src-level> into <dst-level> } } [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IS-IS informationisis
(Optional) Routing process tagisis-tag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
(Optional) Clear IS-IS IPv4 informationip
Clear IS-IS route-map informationroute-map
Clear IS-IS route-map statisticsstatistics
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Enhanced Interior Gateway Protocoleigrp
Autonomous system numberas
IS-IS Routing for IPv4src-isis
Open Shortest Path First (OSPF)ospf
RIP for IPv4rip
Process tagtag
Static routesstatic
Directly connecteddirect
AMT anycast prefixamt
Distribute routes between ISIS levelsdistribute
from level-n into level-minto
Route-distribution between levelssrc-level
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)617
C Commandsclear isis route-map statistics
Page 762
Route-distribution between levelsdst-level
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)618
C Commandsclear isis route-map statistics
Page 763
clear isis spf-logclear isis [ <isis-tag> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] spf-log [ vrf { <vrf-name> |<vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IS-IS informationisis
(Optional) Routing process tagisis-tag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Display IS-IS SPF informationspf-log
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)619
C Commandsclear isis spf-log
Page 764
clear isis statisticsclear isis [ <isis-tag> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] statistics { * | <interface> } [ vrf {<vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IS-IS informationisis
(Optional) Routing process tagisis-tag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear IS-IS protocol statisticsstatistics
All IS-IS protocol statistics*
IS-IS interfaceinterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)620
C Commandsclear isis statistics
Page 765
clear isis trafficclear isis [ <isis-tag> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] traffic { * | <interface> } [ vrf {<vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear IS-IS informationisis
(Optional) Routing process tagisis-tag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear IS-IS traffic informationtraffic
All IS-IS traffic information*
IS-IS interfaceinterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)621
C Commandsclear isis traffic
Page 766
clear itd statisticsclear itd statistics <service-name>
Syntax Description
Reset functionsclear
ITD serviceitd
ITD statisticsstatistics
ITD service-nameservice-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)622
C Commandsclear itd statistics
Page 767
clear keystoreclear { keystore | sksd } [ <index> | <name> ]
Syntax Description
Reset functionsclear
Clear all records in the keystorekeystore
Clear all records in the keystore/sksd-chipsksd
(Optional) Clear secret at index <index>index
(Optional) Clear secret with name <name>name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)623
C Commandsclear keystore
Page 768
clear l2dbgclear l2dbg { macdb | portdb | rvtepdb | dme-events }
Syntax Description
Clearclear
L2 debug databasesl2dbg
L2 debug MACDBmacdb
L2 debug PORTDBportdb
L2 debug RVTEPDBrvtepdb
L2 debug ObjectstoreDBdme-events
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)624
C Commandsclear l2dbg
Page 769
clear l2fwder statisticsclear l2fwder statistics
Syntax Description
Reset functionsclear
Clear L2FWDER related informationl2fwder
Clear the L2FWDER packet countersstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)625
C Commandsclear l2fwder statistics
Page 770
clear l3vm event-historyclear l3vm event-history { pss | errors | mts | reinit | cli | vrf | topology | all }
Syntax Description
Reset functionsclear
Debug L3VM informationl3vm
log debug events into event history bufferevent-history
L3VM pss operationpss
L3VM errorserrors
L3VM MTS messagesmts
L3VM reinit eventsreinit
Log L3VM CLI related eventscli
Log VRF related eventsvrf
Log Topology related eventstopology
All L3VM debuggingall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)626
C Commandsclear l3vm event-history
Page 771
clear lacp countersclear lacp counters [ interface <if0> ]
Syntax Description
Reset functionsclear
LACP protocollacp
LACP counterscounters
(Optional) Specify a port-channelinterface
(Optional)if0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)627
C Commandsclear lacp counters
Page 772
clear ldap-server statisticsclear ldap-server statistics <host0> [ __readonly__ { <server_state> [ <clock_time> { monitoring_statistics<time_in_pstate> <ndead> <tt_in_dstate> } ] } { { auth_statistics <auth_failed_transactions><auth_succ_transactions> <auth_req_sent> <auth_req_timedout> <auth_resp_no_match><auth_resp_not_processed> <auth_resp_error> } { acct_statistics <acct_failed_transactions><acct_succ_transactions> <acct_req_sent> <acct_req_timedout> <acct_resp_no_match><acct_resp_not_processed> <acct_resp_error> } } ]
Syntax Description
Reset functionsclear
Clear LDAP related parametersldap-server
Clear LDAP statisticsstatistics
DNS name or IP addresshost0
(Optional)__readonly__
(Optional) Show state of serverserver_state
(Optional) Show clock time in terms of hours, minutes and secondsclock_time
(Optional) Monitoring Statisticsmonitoring_statistics
(Optional) Time in previous statetime_in_pstate
(Optional) Number of times deadndead
(Optional) Total time in dead statett_in_dstate
(Optional) Authentication Statisticsauth_statistics
(Optional) Accounting Statisticsacct_statistics
(Optional) Authentication: Failed transactionsauth_failed_transactions
(Optional) Authentication: Successful transactionsauth_succ_transactions
(Optional) Authentication: Requests sentauth_req_sent
(Optional) Authentication: Requests timedoutauth_req_timedout
(Optional) Authentication: Responses with no matching requestsauth_resp_no_match
(Optional) Authentication: Responses not processedauth_resp_not_processed
(Optional) Authentication: Responses containing errorsauth_resp_error
(Optional) Accounting: Failed transactionsacct_failed_transactions
(Optional) Accounting: Successful transactionsacct_succ_transactions
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)628
C Commandsclear ldap-server statistics
Page 773
(Optional) Accounting: Requests sentacct_req_sent
(Optional) Accounting: Requests timedoutacct_req_timedout
(Optional) Accounting: Responses with no matching requestsacct_resp_no_match
(Optional) Accounting: Responses not processedacct_resp_not_processed
(Optional) Accounting: Responses containing errorsacct_resp_error
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)629
C Commandsclear ldap-server statistics
Page 774
clear licenseclear license { <license-file> [ force ] | sprom | <s0> }
Syntax Description
Reset functionsclear
clear licenselicense
License file to be uninstalledlicense-file
(Optional) Force license clear (don't prompt)force
clear license contents in spromsprom
License file to be uninstalleds0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)630
C Commandsclear license
Page 775
clear lim countersclear lim counters [ timeline ]
Syntax Description
Clear lim countersclear
clear lim counterslim
clear lim counterscounters
(Optional) Clear all lim counterstimeline
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)631
C Commandsclear lim counters
Page 776
clear lineclear line <s0>
Syntax Description
Reset functionsclear
Kill a session on particular vtyline
Enter the vty names0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)632
C Commandsclear line
Page 777
clear lisp ddt referral-cacheclear lisp ddt referral-cache [ instance-id <iid> ] [ <eid-prefix> | <eid-prefix6> ] [ vrf { <vrf-name> |<vrf-known-name> } ]
Syntax Description
Reset functionsclear
LISP clear commandslisp
LISP Delegated Database Treeddt
Clear the DDT referral cachereferral-cache
(Optional) Clear entry for particular vrfvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Clear entry for specific instance-IDinstance-id
(Optional) 24-bit instance-ID valueiid
(Optional) Clear entry associated with IP EID-prefixeid-prefix
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)633
C Commandsclear lisp ddt referral-cache
Page 778
clear lisp dynamic-eidclear lisp dynamic-eid { <dyn-eid-name> | <dyn-eid> } [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
Reset functionsclear
LISP clear commandslisp
Clear dynamic-EID statedynamic-eid
IPv4 address of dynamic-EID entrydyn-eid
Clear entries discovered for a dynamic-EID rangedyn-eid-name
(Optional) Clear dynamic-EID entries for vrfvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)634
C Commandsclear lisp dynamic-eid
Page 779
clear lisp proxy-itrclear lisp proxy-itr [ <addr> | <addr6> ] [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
Reset functionsclear
LISP clear commandslisp
Clear discovered PITRsproxy-itr
(Optional) IPv4 locator address of PITRaddr
(Optional) Clear proxy-itr state for vrfvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)635
C Commandsclear lisp proxy-itr
Page 780
clear lisp siteclear lisp site <site-name> [ instance-id <iid> ] [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
Reset functionsclear
LISP clear commandslisp
Clear site registration datasite
Clear registration data for a single sitesite-name
(Optional) Clear registration for a single instance-id within a siteinstance-id
(Optional) 24-bit instance-ID valueiid
(Optional) Clear site entries for vrfvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)636
C Commandsclear lisp site
Page 781
clear lldp countersclear lldp counters
Syntax Description
Reset functionsclear
Reset the lldp counterslldp
Reset the lldp traffic counters to zerocounters
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)637
C Commandsclear lldp counters
Page 782
clear lldp counters interfaceclear lldp counters interface <if0>
Syntax Description
Reset functionsclear
Reset the lldp counterslldp
Reset the lldp traffic counters to zerocounters
Clear lldp traffic counters per interfaceinterface
Enter interfaceif0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)638
C Commandsclear lldp counters interface
Page 783
clear logging ip access-list cacheclear logging ip access-list cache
Syntax Description
Reset functionsclear
Clear logging informationlogging
IP configurationip
Access-listaccess-list
loggingcache
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)639
C Commandsclear logging ip access-list cache
Page 784
clear logging logfileclear logging logfile
Syntax Description
Reset functionsclear
Clear logging informationlogging
Clear logfile messageslogfile
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)640
C Commandsclear logging logfile
Page 785
clear logging nvramclear logging nvram
Syntax Description
Reset functionsclear
Clear logging informationlogging
Clear nvram logsnvram
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)641
C Commandsclear logging nvram
Page 786
clear logging onboardclear logging onboard [ { counter-stats | epld-log | internal { <dc3_options> } | module <module> [ {counter-stats | internal { <dc3_options> } } ] } ]
Syntax Description
Reset functionsclear
Clear logging informationlogging
Clear OBFL informationonboard
(Optional) Clear OBFL counter statisticscounter-stats
(Optional) Clear EPLD logepld-log
(Optional) Clear Logging Onboard Internalinternal
(Optional) Clear OBFL information for Modulemodule
(Optional) Enter module numbermodule
(Optional) Clear OBFL counter statisticscounter-stats
(Optional) dc3 optionsdc3_options
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)642
C Commandsclear logging onboard
Page 787
clear logging onboardclear logging onboard [ { card-boot-history | card-first-power-on | environmental-history | error-stats |exception-log | interrupt-stats | module <module> [ { environmental-history | error-stats | exception-log |interrupt-stats | obfl-logs | stack-trace | card-boot-history | card-first-power-on } ] | obfl-logs | stack-trace } ]
Syntax Description
Reset functionsclear
Clear logging informationlogging
Clear OBFL informationonboard
(Optional) Clear OBFL environmental historyenvironmental-history
(Optional) Clear OBFL error statisticserror-stats
(Optional) Clear OBFL exception logexception-log
(Optional) Clear OBFL interrupt statisticsinterrupt-stats
(Optional) Clear Card Boot Historycard-boot-history
(Optional) Clear Card First Power Oncard-first-power-on
(Optional) Clear OBFL information for Modulemodule
(Optional) Enter module numbermodule
(Optional) Clear OBFL (boot-uptime/device-version/obfl-history).obfl-logs
(Optional) Clear OBFL stack tracestack-trace
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)643
C Commandsclear logging onboard
Page 788
clear logging sessionclear logging session
Syntax Description
Reset functionsclear
Clear logging informationlogging
Clear logging sessionsession
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)644
C Commandsclear logging session
Page 789
clear mac address-table datapathclear mac address-table datapath { dynamic [ vlan <id> ] | static [ vlan <id> ] | { statistics [ interface ] } |isis_intf_stats }
Syntax Description
Clearclear
MAC configuration commandsmac
MAC Address Tableaddress-table
Titanium Datapath Tabledatapath
clear dynamic entries from Titanium PD Forwarding Tabledynamic
USE WITH CAUTION!! clear static entries from Titanium PDForwarding Table
static
(Optional) VLANvlan
(Optional) VLAN IDid
Clear datapath statisticsstatistics
(Optional) Clear datapath interface statisticsinterface
Statistics of ISIS Frames Tx/Rxisis_intf_stats
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)645
C Commandsclear mac address-table datapath
Page 790
clear mac address-table dynamicclear mac address-table dynamic [ local ] [ address <mac-addr> | interface <interface-name> ] [ multicast-entries[ not-notified ] ] [ vlan <vlan-id> | vni <vni-id> | peer-ip <peer-ipv4> ] [ instance <instance> ] [ __readonly__<info_str> ]
Syntax Description
Clearclear
MAC configuration commandsmac
MAC Address Tableaddress-table
clear dynamic entries from the Layer2 Forwarding Tabledynamic
(Optional) clear MAC Entries Learned Locally and Not on theOverlay/VXLAN
local
(Optional) addressaddress
(Optional) MAC Addressmac-addr
(Optional) Interfaceinterface
(Optional) Interface nameinterface-name
(Optional) VLANvlan
(Optional) VLAN IDvlan-id
(Optional) VXLAN Network Identifiervni
(Optional) VXLAN Network Identifiervni-id
(Optional) VXLAN Peer IP Addresspeer-ip
(Optional) VXLAN Peer IP Addresspeer-ipv4
(Optional) Eureka Instanceinstance
(Optional) ASIC Instance Numberinstance
(Optional) clear all dynamically learnt multicast entriesmulticast-entries
(Optional) entries that exceed the hardware notification limitnot-notified
(Optional)__readonly__
(Optional) Informationinfo_str
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)646
C Commandsclear mac address-table dynamic
Page 791
clear mts message statisticsclear mts message statistics
Syntax Description
Reset functionsclear
MTS statisticsmts
mts messagesmessage
mts message statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)647
C Commandsclear mts message statistics
Page 792
clear mvr countersclear mvr counters
Syntax Description
Reset functionsclear
Clear MVR infomvr
Clear MVR counterscounters
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)648
C Commandsclear mvr counters
Page 793
clear mvr counters receiver-portsclear mvr counters receiver-ports [ <if0> ]
Syntax Description
Reset functionsclear
Clear MVR infomvr
Clear MVR counterscounters
Clear MVR receiver port countersreceiver-ports
(Optional) Interface nameif0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)649
C Commandsclear mvr counters receiver-ports
Page 794
clear mvr counters source-portsclear mvr counters source-ports [ <if0> ]
Syntax Description
Reset functionsclear
Clear MVR infomvr
Clear MVR counterscounters
Clear MVR source port counterssource-ports
(Optional) Interface nameif0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)650
C Commandsclear mvr counters source-ports
Page 795
clear nbm flow statisticsclear nbm flow statistics
Syntax Description
Clearclear
Non blocking Multicastnbm
NBM flowsflow
Clear nbm flow statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)651
C Commandsclear nbm flow statistics
Page 796
clear ngoamclear ngoam { probe { statistics { summary | { session { <handle> | all } } } } }
Syntax Description
Reset functionsclear
ngoam informationngoam
clear ngoam probeprobe
clear ngoam statisticsstatistics
clear ngoam statistics summarysummary
clear ngoam information by session handlesession
specify session handlehandle
clear stats for all probe sessionsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)652
C Commandsclear ngoam
Page 797
clear ngoamclear ngoam { { interface statistics } }
Syntax Description
Reset functionsclear
ngoam informationngoam
probe packet interfaceinterface
clear ngoam statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)653
C Commandsclear ngoam
Page 798
clear ngoamclear ngoam { loopback { { session { <ses-hdl> | all } } | { statistics { summary | { session { <ses-hdl> | all} } } } | database [ session <ses-hdl> ] } [ force ] }
Syntax Description
Reset functionsclear
ngoam informationngoam
clear ngoam loopbackloopback
clear ngoam statisticsstatistics
clear ngoam statistics summarysummary
clear ngoam databasedatabase
clear ngoam information by session handlesession
specify session handleses-hdl
clear stats for all ping sessionsall
(Optional) Clear it, do not ask to confirmforce
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)654
C Commandsclear ngoam
Page 799
clear ngoamclear ngoam { traceroute { { session { <handle> | all } } | { statistics { summary | { session { <handle> | all} } } } } [ force ] }
Syntax Description
Reset functionsclear
ngoam informationngoam
clear ngoam traceroutetraceroute
clear ngoam statisticsstatistics
clear ngoam statistics summarysummary
clear ngoam information by session handlesession
specify session handlehandle
clear stats for all traceroute sessionsall
(Optional) Clear it, do not ask to confirmforce
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)655
C Commandsclear ngoam
Page 800
clear ngoam pathtraceclear ngoam pathtrace { { statistics { summary | { session { <handle> | all } } } } | { database { session {<handle> | all } } } } [ force ]
Syntax Description
Reset functionsclear
ngoam informationngoam
clear ngoam pathracepathtrace
clear ngoam pathtrace databasedatabase
clear ngoam statisticsstatistics
clear ngoam statistics summarysummary
clear ngoam information by session handlesession
specify session handlehandle
clear stats for all pathtrace sessionsall
(Optional) Clear it, do not ask to confirmforce
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)656
C Commandsclear ngoam pathtrace
Page 801
clear ntp sessionclear ntp session
Syntax Description
Reset functionsclear
Network Time Protocolntp
Clear the ntp configuration sessionsession
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)657
C Commandsclear ntp session
Page 802
clear ntp statisticsclear ntp statistics { all-peers | io | local | memory }
Syntax Description
Reset functionsclear
Network Time Protocolntp
Clear NTP Statisticsstatistics
Clear per-peer statistics counter of all peersall-peers
Clear input-output statisticsio
Clear counters maintained by the local NTPlocal
Clear statistics counters related to memory codememory
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)658
C Commandsclear ntp statistics
Page 803
clear nvramclear nvram
Syntax Description
Reset functionsclear
purge NVRAMnvram
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)659
C Commandsclear nvram
Page 804
clear nxapi-server logsclear nxapi-server logs
Syntax Description
Reset functionsclear
Clear NX-API Servernxapi-server
Clear NX-API Server logslogs
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)660
C Commandsclear nxapi-server logs
Page 805
clear openflow switch controller allclear openflow switch <switch-id> controller all
Syntax Description
Reset functionsclear
Clear OpenFlow switch informationopenflow
Logical switch idswitch
Logical switch-idswitch-id
Controllercontroller
Allall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)661
C Commandsclear openflow switch controller all
Page 806
clear ospfv3 databaseclear ospfv3 [ <tag> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] database [ vrf { <vrf-name> |<vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear OSPF tablesospfv3
(Optional) Process tagtag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear the LSDB and all neighborsdatabase
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)662
C Commandsclear ospfv3 database
Page 807
clear ospfv3 event-historyclear ospfv3 [ <tag> ] event-history [ adjacency | event | ha | flooding | lsa | spf | redistribution | cli | hello |spf-trigger | all ]
Syntax Description
Reset functionsclear
Debugging functionsospfv3
(Optional) Process tagtag
Clear the event history buffersevent-history
(Optional) Adjacency formation logsadjacency
(Optional) Internal event logsevent
(Optional) HA and GR logsha
(Optional) LSA flooding logsflooding
(Optional) LSA generation and databse logslsa
(Optional) SPF calculation logsspf
(Optional) Redistribution logsredistribution
(Optional) Cli logscli
(Optional) HELLO related logshello
(Optional) SPF TRIGGER related logsspf-trigger
(Optional) All event history buffersall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)663
C Commandsclear ospfv3 event-history
Page 808
clear ospfv3 interfaceclear ospfv3 [ <tag> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] interface { * | <interface> } [ vrf {<vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear OSPF tablesospfv3
(Optional) Process tagtag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear one or more interfacesinterface
Clear all interfaces*
Interface to clearinterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)664
C Commandsclear ospfv3 interface
Page 809
clear ospfv3 neighborclear ospfv3 [ <tag> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] neighbor { * | <neighborid> | <interface>} [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear OSPF tablesospfv3
(Optional) Process tagtag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear one or more neighborsneighbor
Clear all neighbors*
Source IP address, or router ID of the neighborneighborid
Interface to clear all neighbors oninterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)665
C Commandsclear ospfv3 neighbor
Page 810
clear ospfv3 policy statisticsclear ospfv3 [ <tag> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] policy statistics { { redistribute { bgp<as> | { eigrp | isis | rip } <tag> | static | direct | amt | lisp } } | { area <area-id-ip> filter-list { in | out } } } [vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Display OSPFv3 status and configurationospfv3
(Optional) Process tagtag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear Policy related informationpolicy
Display Route Filter statisticsstatistics
Statistics for redistributionredistribute
Enhanced Interior Gateway Protocol (EIGRP)eigrp
Routing Information Protocol (RIP)rip
ISO Intermediate-to-Intermediate (IS-IS)isis
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
Staticstatic
Directly connecteddirect
AMT anycast prefixamt
LISP EID-prefixeslisp
Configure area propertiesarea
Area Id as an integer or ip addressarea-id-ip
Filter prefixes between OSPF areasfilter-list
Filter networks sent to this areain
Filter networks sent from this areaout
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)666
C Commandsclear ospfv3 policy statistics
Page 811
tag
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)667
C Commandsclear ospfv3 policy statistics
Page 812
clear ospfv3 statisticsclear ospfv3 [ <tag> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] statistics [ vrf { <vrf-name> |<vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear OSPF tablesospfv3
(Optional) Process tagtag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear statistics countersstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)668
C Commandsclear ospfv3 statistics
Page 813
clear ospfv3 trafficclear ospfv3 [ <tag> ] [ vrf { <vrf-name> | <vrf-known-name> | all } ] traffic [ <interface> ] [ vrf { <vrf-name>| <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear OSPF tablesospfv3
(Optional) Process tagtag
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Clear traffic counterstraffic
(Optional) Interface to clear all traffic oninterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)669
C Commandsclear ospfv3 traffic
Page 814
clear peer-info interface vsanclear peer-info interface <iface> vsan <vsan_id>
Syntax Description
Reset functionsclear
clear rnid informationpeer-info
clear peer rnid information for a port in a vsaninterface
iface
clear peer rnid informationvsan
Enter VSAN numbervsan_id
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)670
C Commandsclear peer-info interface vsan
Page 815
clear pktmgr clientclear pktmgr client [ <uuid> ]
Syntax Description
Reset functionsclear
Clear Packet Manager informationpktmgr
Clear pktmgr clients countersclient
(Optional) Clear pktmgr client counters for given uuiduuid
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)671
C Commandsclear pktmgr client
Page 816
clear pktmgr interfaceclear pktmgr interface [ <interface> ]
Syntax Description
Reset functionsclear
Clear Packet Manager informationpktmgr
Clear pktmgr related interface informationinterface
(Optional) Interface name to displayinterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)672
C Commandsclear pktmgr interface
Page 817
clear plb analyticsclear plb analytics <service-name>
Syntax Description
Reset functionsclear
PLB serviceplb
PLB analyticsanalytics
PLB service nameservice-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)673
C Commandsclear plb analytics
Page 818
clear port-security dynamic address vlanclear port-security dynamic address <mac-address> vlan <vlanid>
Syntax Description
Reset functionsclear
Clear port-security informationport-security
dynamic addressesdynamic
secure addressaddress
48 bit mac addressmac-address
vlan informationvlan
vlan id. Enter a value between 1 and 4094vlanid
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)674
C Commandsclear port-security dynamic address vlan
Page 819
clear port-security dynamic interfaceclear port-security dynamic interface <if_index> [ vlan <vlanid> ]
Syntax Description
Reset functionsclear
Clear port-security informationport-security
dynamic addressesdynamic
interfaceinterface
ethernetif_index
(Optional) vlan informationvlan
(Optional) vlan id. Enter a value between 1 and 4094vlanid
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)675
C Commandsclear port-security dynamic interface
Page 820
clear processes log allclear processes log all
Syntax Description
Reset functionsclear
process-related clear commandsprocesses
Delete log fileslog
Delete all the log filesall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)676
C Commandsclear processes log all
Page 821
clear processes log all vdc-allclear processes log all vdc-all
Syntax Description
Reset functionsclear
process-related clear commandsprocesses
Delete log fileslog
Delete all the log filesall
Delete all the log files in all vdcsvdc-all
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)677
C Commandsclear processes log all vdc-all
Page 822
clear processes log archiveclear processes log archive [ file <s0> ]
Syntax Description
Reset functionsclear
system manager spawned processesprocesses
Delete log fileslog
clear all process logs for this vdc from logflash on this modulearchive
(Optional) delete a log file on logflashfile
(Optional) Name of file in directory 'logs0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)678
C Commandsclear processes log archive
Page 823
clear processes log pidclear processes log pid <i0>
Syntax Description
Reset functionsclear
process-related clear commandsprocesses
Delete log fileslog
Delete log file of a specific processpid
pid of the processi0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)679
C Commandsclear processes log pid
Page 824
clear processes vdc log allclear processes vdc <e-vdc2> log all
Syntax Description
Reset functionsclear
process-related clear commandsprocesses
process-related clear commands in vdcvdc
Enter Virtual Device Context <vdc-id>e-vdc2
Delete log fileslog
Delete all the log filesall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)680
C Commandsclear processes vdc log all
Page 825
clear processes vdc log pidclear processes vdc <e-vdc2> log pid <i1>
Syntax Description
Reset functionsclear
process-related clear commandsprocesses
process-related clear commands in vdcvdc
Enter Virtual Device Context <vdc-id>e-vdc2
Delete log fileslog
Delete log file of a specific processpid
pid of the processi1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)681
C Commandsclear processes vdc log pid
Page 826
clear ptp correctionsclear ptp corrections
Syntax Description
Reset functionsclear
Precision Time Protocol (IEEE 1588) Subsystemptp
Clear history of PTP correctionscorrections
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)682
C Commandsclear ptp corrections
Page 827
clear ptp counters interfaceclear ptp counters { interface <if0> | all }
Syntax Description
Reset functionsclear
Precision Time Protocol (IEEE 1588) Subsystemptp
Clear PTP packet counterscounters
Clear for specific interfaceinterface
Clear for all interfacesall
if0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)683
C Commandsclear ptp counters interface
Page 828
clear qos policiesclear qos policies
Syntax Description
Reset functionsclear
Clear default policiespolicies
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)684
C Commandsclear qos policies
Page 829
clear qos policies forceclear qos policies force
Syntax Description
Reset functionsclear
Clear default policiespolicies
Clear forcefullyforce
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)685
C Commandsclear qos policies force
Page 830
clear qos statisticsclear qos statistics [ { interface [ <iface-list> ] | vlan [ <vlan-list> ] } [ input | output ] [ type <qos-or-q> ] ]
Syntax Description
Reset functionsclear
Clear statisticsstatistics
(Optional) Clear statistics on a interfaceinterface
(Optional) List of Interfacesiface-list
(Optional) 802.1Q vlanvlan
(Optional) List of vlan idsvlan-list
(Optional) Input Service policyinput
(Optional) Output Service policyoutput
(Optional) Policy typetype
(Optional)qos-or-q
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)686
C Commandsclear qos statistics
Page 831
clear queuing burst-detectclear queuing burst-detect [ interface <if_name> [ queue <queue_num> ] ] [ module <module> ]
Syntax Description
Clear all entriesclear
Queuing related informationqueuing
Out of Band micro-burst queue statisticsburst-detect
(Optional) Interfaceinterface
(Optional) interface nameif_name
(Optional) Queue number for displaying statisticsqueue
(Optional) Queue numberqueue_num
(Optional) Slot/modulemodule
(Optional) Slot/module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)687
C Commandsclear queuing burst-detect
Page 832
clear queuing pfc-queueclear queuing pfc-queue [ interface <if_list> ]
Syntax Description
Reset functionsclear
clear queuing related countersqueuing
clear watchdog timerspfc-queue
(Optional) Interfaceinterface
(Optional) List of interfacesif_list
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)688
C Commandsclear queuing pfc-queue
Page 833
clear queuing pfc-queue interfaceclear queuing pfc-queue interface <if_list>
Syntax Description
Reset functionsclear
clear queuing related countersqueuing
clear watchdog timerspfc-queue
Interfaceinterface
List of interfacesif_list
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)689
C Commandsclear queuing pfc-queue interface
Page 834
clear queuing tah-pfc-queueclear queuing tah-pfc-queue [ interface <if_list> ] [ module <module> ]
Syntax Description
Clearclear
Queuing related informationqueuing
PFC watchdog queuing related statstah-pfc-queue
(Optional) Interface for clearing queuing statsinterface
(Optional) List of interfacesif_list
(Optional) Slot/modulemodule
(Optional) Slot/module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)690
C Commandsclear queuing tah-pfc-queue
Page 835
clear radius-server statisticsclear radius-server statistics <host0> [ __readonly__ { <server_state> [ <clock_time> { monitoring_statistics<time_in_pstate> <ndead> <tt_in_dstate> } ] } { { auth_statistics <auth_failed_transactions><auth_succ_transactions> <auth_req_sent> <auth_req_timedout> <auth_resp_no_match><auth_resp_not_processed> <auth_resp_error> } { acct_statistics <acct_failed_transactions><acct_succ_transactions> <acct_req_sent> <acct_req_timedout> <acct_resp_no_match><acct_resp_not_processed> <acct_resp_error> } } ]
Syntax Description
Reset functionsclear
Clear RADIUS related parametersradius-server
Clear RADIUS statisticsstatistics
DNS name or IP addresshost0
(Optional)__readonly__
(Optional) Show state of serverserver_state
(Optional) Show clock time in terms of hours, minutes and secondsclock_time
(Optional) Monitoring Statisticsmonitoring_statistics
(Optional) Time in previous statetime_in_pstate
(Optional) Number of times deadndead
(Optional) Total time in dead statett_in_dstate
(Optional) Authentication Statisticsauth_statistics
(Optional) Accounting Statisticsacct_statistics
(Optional) Authentication: Failed transactionsauth_failed_transactions
(Optional) Authentication: Successful transactionsauth_succ_transactions
(Optional) Authentication: Requests sentauth_req_sent
(Optional) Authentication: Requests timedoutauth_req_timedout
(Optional) Authentication: Responses with no matching requestsauth_resp_no_match
(Optional) Authentication: Responses not processedauth_resp_not_processed
(Optional) Authentication: Responses containing errorsauth_resp_error
(Optional) Accounting: Failed transactionsacct_failed_transactions
(Optional) Accounting: Successful transactionsacct_succ_transactions
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)691
C Commandsclear radius-server statistics
Page 836
(Optional) Accounting: Requests sentacct_req_sent
(Optional) Accounting: Requests timedoutacct_req_timedout
(Optional) Accounting: Responses with no matching requestsacct_resp_no_match
(Optional) Accounting: Responses not processedacct_resp_not_processed
(Optional) Accounting: Responses containing errorsacct_resp_error
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)692
C Commandsclear radius-server statistics
Page 837
clear radius sessionclear radius session
Syntax Description
Reset functionsclear
clear to be commited RADIUS config and lock in fabricradius
clear to be commited RADIUS config and lock in fabricsession
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)693
C Commandsclear radius session
Page 838
clear rmonclear rmon { alarms | events | logs | hcalarms | all-alarms }
Syntax Description
Reset functionsclear
Clear RMON tablesrmon
Clear all 32 bit alarmsalarms
Clear rmon log this also clears rmon event tableevents
Clear rmon loglogs
Clear all 64 bit rmon alarmshcalarms
Clear all 32 bit and 64 bit rmon alarmsall-alarms
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)694
C Commandsclear rmon
Page 839
clear route-map pbr-statisticsclear route-map { <route-map-name> | <route-map-cfg-name> } pbr-statistics
Syntax Description
Reset functionsclear
Route-map used for PBRroute-map
Route-map nameroute-map-name
Known route-map nameroute-map-cfg-name
Statistics for policy based routingpbr-statistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)695
C Commandsclear route-map pbr-statistics
Page 840
clear routing event-historyclear routing [ ip | ipv4 ] [ unicast ] event-history { add-route | cli | delete-route | detail | errors | general | ha |loop-detection | modify-route | notifications | recursive-next-hop | summary | ufdm | ufdm-detail | ufdm-summary}
Syntax Description
Reset functionsclear
Clear routing informationrouting
(Optional) Clear IP commandsip
(Optional) Clear IP commandsipv4
(Optional) Clear unicast informationunicast
Clear routing event logevent-history
Add routeadd-route
CLIcli
Delete routedelete-route
Detaildetail
Errorserrors
Generalgeneral
HAha
Loop detectionloop-detection
Modify routemodify-route
Notificationnotifications
Recursive next hoprecursive-next-hop
Summarysummary
UFDMufdm
UFDM Detailufdm-detail
UFDM Summaryufdm-summary
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)696
C Commandsclear routing event-history
Page 841
clear routing ip multicast mfdm pending countersclear routing ip multicast mfdm pending counters [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear routing informationrouting
Clear IP commandsip
Clear MRIB informationmulticast
Clear MFDM informationmfdm
Clear MFDM pending informationpending
MFDM counterscounters
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)697
C Commandsclear routing ip multicast mfdm pending counters
Page 842
clear routing ip multicast rpf-source retry-cacheclear routing ip multicast rpf-source retry-cache [ vrf { <vrf-name> | <vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear routing informationrouting
Clear IP commandsip
Clear MRIB informationmulticast
Clear RPF-Source informationrpf-source
Clear retry-cache informationretry-cache
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)698
C Commandsclear routing ip multicast rpf-source retry-cache
Page 843
clear routing ipv6 event-historyclear routing ipv6 [ unicast ] event-history { am | cli | detail | errors | general | ha | lfe | recursive-next-hop |summary | ufdm | ufdm-detail | ufdm-summary }
Syntax Description
Reset functionsclear
Clear routing informationrouting
Clear IPv6 commandsipv6
(Optional) Clear unicast informationunicast
Clear routing event logevent-history
AMam
CLIcli
Detaildetail
Errorserrors
Generalgeneral
HAha
LFElfe
Recursive next hoprecursive-next-hop
Summarysummary
UFDMufdm
UFDM Detailufdm-detail
UFDM Summaryufdm-summary
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)699
C Commandsclear routing ipv6 event-history
Page 844
clear routing ipv6 multicastclear routing ipv6 multicast { <all> | <group-prefix> | <group> [ <source> ] } [ vrf { <vrf-name> |<vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear routing informationrouting
Clear IPv6 commandsipv6
Clear multicast routing tablemulticast
Clear all routesall
(Optional) Clear information for particular VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)700
C Commandsclear routing ipv6 multicast
Page 845
clear routing multicastclear routing [ ip | ipv4 ] multicast { <all> | <group-prefix> | <group> [ <source> ] } [ vrf { <vrf-name> |<vrf-known-name> | all } ]
Syntax Description
Reset functionsclear
Clear routing informationrouting
(Optional) Clear IP commandsip
(Optional) Clear IP commandsipv4
Clear multicast routing tablemulticast
Clear all routesall
Clear all routes within the Group prefixgroup-prefix
Clear all routes matching Groupgroup
(Optional) Clear a (S,G) routesource
(Optional) Clear information for particular VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Display information for all VRFsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)701
C Commandsclear routing multicast
Page 846
clear scheduler logfileclear scheduler logfile
Syntax Description
Reset functionsclear
Scheduler clear commandsscheduler
Clear scheduler log filelogfile
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)702
C Commandsclear scheduler logfile
Page 847
clear screenclear screen
Syntax Description
Reset functionsclear
Clear screenscreen
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)703
C Commandsclear screen
Page 848
clear session state nameclear session state name <s4>
Syntax Description
Reset functionsclear
Reset confg session internalssession
Reset confg session internal statestate
Reset confg session internal state for a given namename
Enter the name of the sessions4
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)704
C Commandsclear session state name
Page 849
clear sflow statisticsclear sflow statistics
Syntax Description
Reset functionsclear
sFlow global configurationsflow
Clear sFlow statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)705
C Commandsclear sflow statistics
Page 850
clear snmp countersclear snmp counters
Syntax Description
Reset functionsclear
Clear SNMP Tablessnmp
Clear SNMP counterscounters
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)706
C Commandsclear snmp counters
Page 851
clear snmp hostconfigclear snmp hostconfig
Syntax Description
Reset functionsclear
Clear SNMP Tablessnmp
Clear SNMP Host Listhostconfig
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)707
C Commandsclear snmp hostconfig
Page 852
clear sockets statisticsclear sockets statistics { all | tcp | tcp6 | udp | udp6 | raw | raw6 }
Syntax Description
Reset functionsclear
Clear sockets statisticssockets
Clear sockets statisticsstatistics
Clear TCP/UDP/RAW v4/v6 statisticsall
Clear TCP v4 statisticstcp
Clear TCP v6 statisticstcp6
Clear UDP v4 statisticsudp
Clear UDP v6 statisticsudp6
Clear RAW v4 statisticsraw
Clear RAW v6 statisticsraw6
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)708
C Commandsclear sockets statistics
Page 853
clear spanning-tree countersclear spanning-tree counters [ interface <interface-id> | vlan <vlan-id> | bridge-domain <bd-id> ]
Syntax Description
Reset functionsclear
Spanning Tree Subsystemspanning-tree
Clear spanning tree statisticscounters
(Optional) Specify an interface as a target for the commandinterface
(Optional) Specify an interface as a target for the commandinterface-id
(Optional) VLAN Switch Spanning Treesvlan
(Optional) Bridge-Domain Switch Spanning Treesbridge-domain
(Optional) vlan range, Example: 1,3-5,7,9-11vlan-id
(Optional) Bridge-Domain range, Example: 2,4-5,7,9-11bd-id
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)709
C Commandsclear spanning-tree counters
Page 854
clear spanning-tree detected-protocolsclear spanning-tree detected-protocols [ interface <interface-id> ]
Syntax Description
Reset functionsclear
Spanning Tree Subsystemspanning-tree
Restart the protocol migration processdetected-protocols
(Optional) Specify an interface as a target for the commandinterface
(Optional) Specify an interface as a target for the commandinterface-id
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)710
C Commandsclear spanning-tree detected-protocols
Page 855
clear spanning-tree sps-histclear spanning-tree sps-hist
Syntax Description
Reset functionsclear
Spanning Tree Subsystemspanning-tree
Set port state statssps-hist
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)711
C Commandsclear spanning-tree sps-hist
Page 856
clear ssh hostsclear ssh hosts
Syntax Description
Reset functionsclear
Clear ssh valuesssh
Clear the list of trusted ssh hostshosts
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)712
C Commandsclear ssh hosts
Page 857
clear statistics module-allclear statistics module-all
Syntax Description
Clear statisticsclear
Statsstatistics
Clear stats of all modulesmodule-all
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)713
C Commandsclear statistics module-all
Page 858
clear statistics moduleclear statistics module <module>
Syntax Description
Clear statisticsclear
Statsstatistics
Clear stats of a single modulemodule
Enter module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)714
C Commandsclear statistics module
Page 859
clear sup-monitor drops sessionclear sup-monitor drops session <session_number> [ module <module> ]
Syntax Description
Clear the monitor drop countersclear
Show Ethernet SPAN informationsup-monitor
show the dropsdrops
span session numbersession
session_number
(Optional) Slot/modulemodule
(Optional) Slot/module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)715
C Commandsclear sup-monitor drops session
Page 860
clear system login failuresclear system login failures
Syntax Description
Reset functionsclear
System management commandssystem
Secure Loginlogin
Clear login failures in the current watch periodfailures
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)716
C Commandsclear system login failures
Page 861
clear system reset-reasonclear system reset-reason
Syntax Description
Reset functionsclear
Clear logs in systemsystem
Clear reset-reason logs in the systemreset-reason
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)717
C Commandsclear system reset-reason
Page 862
clear tacacs-server statisticsclear tacacs-server statistics <host0> [ __readonly__ { <server_state> [ <clock_time> { monitoring_statistics<time_in_pstate> <ndead> <tt_in_dstate> } ] } { auth_statistics <auth_failed_transactions><auth_succ_transactions> <auth_req_sent> <auth_req_timedout> <auth_resp_no_match><auth_resp_not_processed> <auth_resp_error> } { autho_statistics <autho_failed_transactions><autho_succ_transactions> <autho_req_sent> <autho_req_timedout> <autho_resp_no_match><autho_resp_not_processed> <autho_resp_error> } { acct_statistics <acct_failed_transactions><acct_succ_transactions> <acct_req_sent> <acct_req_timedout> <acct_resp_no_match><acct_resp_not_processed> <acct_resp_error> } ]
Syntax Description
Reset functionsclear
Clear TACACS related parameterstacacs-server
Clear TACACS statisticsstatistics
DNS name or IP addresshost0
(Optional)__readonly__
(Optional) Show state of serverserver_state
(Optional) Show clock time in terms of hours, minutes and secondsclock_time
(Optional) Monitoring Statisticsmonitoring_statistics
(Optional) Time in previous statetime_in_pstate
(Optional) Number of times deadndead
(Optional) Total time in dead statett_in_dstate
(Optional) Authentication Statisticsauth_statistics
(Optional) Authorization Statisticsautho_statistics
(Optional) Accounting Statisticsacct_statistics
(Optional) Authentication: Failed transactionsauth_failed_transactions
(Optional) Authentication: Successful transactionsauth_succ_transactions
(Optional) Authentication: Requests sentauth_req_sent
(Optional) Authentication: Requests timedoutauth_req_timedout
(Optional) Authentication: Responses with no matching requestsauth_resp_no_match
(Optional) Authentication: Responses not processedauth_resp_not_processed
(Optional) Authentication: Responses containing errorsauth_resp_error
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)718
C Commandsclear tacacs-server statistics
Page 863
(Optional) Authorization: Failed transactionsautho_failed_transactions
(Optional) Authorization: Successful transactionsautho_succ_transactions
(Optional) Authorization: Requests sentautho_req_sent
(Optional) Authorization: Requests timedoutautho_req_timedout
(Optional) Authorization: Responses with no matching requestsautho_resp_no_match
(Optional) Authorization: Responses not processedautho_resp_not_processed
(Optional) Authorization: Responses containing errorsautho_resp_error
(Optional) Accounting: Failed transactionsacct_failed_transactions
(Optional) Accounting: Successful transactionsacct_succ_transactions
(Optional) Accounting: Requests sentacct_req_sent
(Optional) Accounting: Requests timedoutacct_req_timedout
(Optional) Accounting: Responses with no matching requestsacct_resp_no_match
(Optional) Accounting: Responses not processedacct_resp_not_processed
(Optional) Accounting: Responses containing errorsacct_resp_error
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)719
C Commandsclear tacacs-server statistics
Page 864
clear tech-support lockclear tech-support lock
Syntax Description
Reset functionsclear
Gather information for troubleshootingtech-support
Clear the lock which prohibits multiple show techs to run in parallellock
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)720
C Commandsclear tech-support lock
Page 865
clear tech-support lockclear tech-support lock
Syntax Description
Reset functionsclear
Gather information for troubleshootingtech-support
Clear the lock which prohibits multiple show techs to run in parallellock
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)721
C Commandsclear tech-support lock
Page 866
clear userclear user <s0>
Syntax Description
Reset functionsclear
Logout a particular useruser
Enter the usernames0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)722
C Commandsclear user
Page 867
clear veobc countersclear veobc counters
Syntax Description
Reset functionclear
Reset the veobc countersveobc
Reset the veobc statistic counters to zerocounters
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)723
C Commandsclear veobc counters
Page 868
clear vlan access-list countersclear vlan access-list counters [ <name> ]
Syntax Description
Reset functionsclear
Vlan commandsvlan
Clear access list statistical informationaccess-list
Clear access list counterscounters
(Optional) List namename
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)724
C Commandsclear vlan access-list counters
Page 869
clear vlan countersclear vlan [ id <vlan-id> ] counters
Syntax Description
Reset functionsclear
Vlan commandsvlan
(Optional) clear VLAN counters by VLAN idid
(Optional) VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19vlan-id
display counterscounters
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)725
C Commandsclear vlan counters
Page 870
clear vmtracker countersclear vmtracker counters
Syntax Description
Clearclear
Clear vmtracker infovmtracker
Clear vmtracker counter infocounters
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)726
C Commandsclear vmtracker counters
Page 871
clear vpc statistics allclear vpc statistics all
Syntax Description
Reset functionsclear
Virtual Port Channel configurationvpc
Statisticsstatistics
All vPC statisticsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)727
C Commandsclear vpc statistics all
Page 872
clear vpc statistics peer-keepaliveclear vpc statistics peer-keepalive
Syntax Description
Reset functionsclear
Virtual Port Channel configurationvpc
Statisticsstatistics
peer keepalive module related statisticspeer-keepalive
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)728
C Commandsclear vpc statistics peer-keepalive
Page 873
clear vpc statistics vpcclear vpc statistics { vpc <vpc_num> | peer-link }
Syntax Description
Reset functionsclear
Statistics for a specific vPCvpc
Statisticsstatistics
Virtual Port Channel numbervpc_num
stats for peer-linkpeer-link
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)729
C Commandsclear vpc statistics vpc
Page 874
clear vpc transport statisticsclear vpc transport statistics [ __readonly__ <last-clear-time> ]
Syntax Description
Reset functionsclear
Virtual Port Channel configurationvpc
cfs transporttransport
Statisticsstatistics
(Optional) Read Only__readonly__
(Optional) time difference from last clear timelast-clear-time
Command Mode
• /exec/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)730
C Commandsclear vpc transport statistics
Page 875
clear vrrp statisticsclear vrrp statistics [ interface <intf_num> ] [ vr <vr_id> ]
Syntax Description
Reset functionsclear
Clear virtual routervrrp
Clear global virtual router statisticsstatistics
(Optional) Select interfaceinterface
(Optional)intf_num
(Optional) [1-255] clear virtual router statisticsvr
(Optional)vr_id
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)731
C Commandsclear vrrp statistics
Page 876
clear vrrpv3 event-historyclear vrrpv3 event-history { debugs | errors | msgs | all }
Syntax Description
Reset functionsclear
VRRPv3 Clear commandsvrrpv3
Clear event history buffers of vrrpv3event-history
Clear debug event buffer of vrrpv3debugs
Clear errors event buffer of vrrpv3errors
Clear MTS event buffer of vrrpv3msgs
Clear all event buffers of vrrpv3all
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)732
C Commandsclear vrrpv3 event-history
Page 877
clear vrrpv3 statisticsclear vrrpv3 statistics [ <interface_num> [ <group_num> ] ] [ <opt_v4_or_v6> ]
Syntax Description
Reset functionsclear
VRRPv3 Clear commandsvrrpv3
VRRPV3 statisticsstatistics
(Optional) Interfaceinterface_num
(Optional) Group numbergroup_num
(Optional) Enter ipv4 or ipv6opt_v4_or_v6
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)733
C Commandsclear vrrpv3 statistics
Page 878
clear vtp countersclear vtp counters
Syntax Description
Reset functionsclear
Clear VTP itemsvtp
Clear VTP counterscounters
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)734
C Commandsclear vtp counters
Page 879
cli alias name{ cli alias name <s0> <line> | no cli alias name <s0> [ <line> ] }
Syntax Description
Negate a command or set its defaultsno
Configure CLI commandscli
Define an aliasalias
Specify the aliasname
Alias commands0
Alias definitionline
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)735
C Commandscli alias name
Page 880
cli create new-cmd{ cli create new-cmd <s0> | no cli create new-cmd <s0> }
Syntax Description
Negate a command or set its defaultsno
Configure cli commandscli
Create a new clicreate
Specify the new clinew-cmd
new cli command (should include spaces)s0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)736
C Commandscli create new-cmd
Page 881
cli var namecli no var name <s0>
Syntax Description
CLI commandscli
Negate a command or set its defaultsno
Unset a variablevar
Specify a variable namename
Variable names0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)737
C Commandscli var name
Page 882
cli var name{ cli var name <s0> <line> | no cli var name <s0> [ <line> ] }
Syntax Description
Negate a command or set its defaultsno
Configure CLI commandscli
Define a variablevar
Specify a variable namename
Variable names0
Variable valueline
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)738
C Commandscli var name
Page 883
cli var name[no] cli var name <s0>
Syntax Description
Negate a command or set its defaultsno
CLI commandscli
Unset a variablevar
Specify a variable namename
Variable names0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)739
C Commandscli var name
Page 884
cli var namecli var name <s0> <line>
Syntax Description
CLI commandscli
Define a variablevar
Specify a variable namename
Variable names0
Variable valueline
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)740
C Commandscli var name
Page 885
cli verifynrun[no] cli verifynrun
Syntax Description
(Optional) Negate a command or set its defaultsno
CLI commandscli
Verify and runverifynrun
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)741
C Commandscli verifynrun
Page 886
client-to-client reflection[no] client-to-client reflection
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure client-to-client route reflectionclient-to-client
reflection of routes permittedreflection
Command Mode
• /exec/configure/router-bgp/router-bgp-af
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)742
C Commandsclient-to-client reflection
Page 887
clis allclis { no debug | undebug } all
Syntax Description
dcos cli commandclis
Negate a command or set its defaultsno
Disable Debugging functions (See also debug)undebug
Debugging functionsdebug
Disableall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)743
C Commandsclis all
Page 888
clock-tolerance ntp oneway absolute{ { no | default } clock-tolerance | clock-tolerance ntp oneway { absolute <abs-value> | percent <percentage>} }
Syntax Description
no
ntpclock-tolerance
Set a command to its defaultsdefault
Set acceptable clock synchronization errorclock-tolerance
Acceptable clock synchronization error due to NTPntp
Acceptable clock synchronization error in oneway measurementoneway
Acceptable error in microsecondsabsolute
Acceptable error as percent of value measuredpercent
Number in microsecondsabs-value
Percentage of one-way delaypercentage
Command Mode
• /exec/configure/ip-sla/jitter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)744
C Commandsclock-tolerance ntp oneway absolute
Page 889
clock format 12[no] clock format { 12-hours | 24-hours }
Syntax Description
(Optional) Negate a command or set its defaultsno
Clockclock
Display format of clockformat
12 hours display12-hours
24 hours display24-hours
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)745
C Commandsclock format 12
Page 890
clock format show-timezone debug[no] clock format show-timezone debug
Syntax Description
(Optional) Negate a command or set its defaultsno
Clockclock
Display format of clockformat
Display the configured timezoneshow-timezone
Display the configured timezone in debugsdebug
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)746
C Commandsclock format show-timezone debug
Page 891
clock format show-timezone syslog[no] clock format show-timezone syslog
Syntax Description
(Optional) Negate a command or set its defaultsno
Clockclock
Display format of clockformat
Display the configured timezoneshow-timezone
Display the configured timezone in syslogssyslog
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)747
C Commandsclock format show-timezone syslog
Page 892
clock protocol[no] clock protocol { ntp | ptp | none } [ vdc <vdc-id> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Clockclock
protocolprotocol
ntpntp
ptpptp
none (clock can be set manually)none
(Optional) vdcvdc
(Optional) vdc-idvdc-id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)748
C Commandsclock protocol
Page 893
clock setclock set <s0> <i0> { April <i1> | August <i2> | December <i3> | February <i4> | January <i5> | July <i6> |June <i7> | March <i8> | May <i9> | November <i10> | October <i11> | September <i12> }
Syntax Description
Clockclock
HH:MM:SS Current Timeset
HH:MM:SS Current Times0
Day of the monthi0
Month of the yearApril
Enter the year (no abbreviation)i1
Month of the yearAugust
Enter the year (no abbreviation)i2
Month of the yearDecember
Enter the year (no abbreviation)i3
Month of the yearFebruary
Enter the year (no abbreviation)i4
Month of the yearJanuary
enter the year (no abbreviation)i5
Month of the yearJuly
Enter the year (no abbreviation)i6
Month of the yearJune
Enter the year (no abbreviation)i7
Month of the yearMarch
Enter the year (no abbreviation)i8
Month of the yearMay
Enter the year (no abbreviation)i9
Month of the yearNovember
Enter the year (no abbreviation)i10
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)749
C Commandsclock set
Page 894
Month of the yearOctober
Enter the year (no abbreviation)i11
Month of the yearSeptember
Enter the year (no abbreviation)i12
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)750
C Commandsclock set
Page 895
clock summer{ clock { summer-time <s0> [ <i0> <s1> <s2> <s3> <i1> <s4> <s5> <s6> [ <i2> ] ] | timezone <s7> <i3><i4> } | no clock { summer-time [ <s0> <i0> <s1> <s2> <s3> <i1> <s4> <s5> <s6> <i2> ] | timezone [ <s7><i3> <i4> ] } }
Syntax Description
Negate a command or set its defaultsno
Clockclock
Configure summer (daylight savings) timesummer-time
Name of time zone in summer, such as PDT, CDT, EDT, etc..s0
(Optional) Week number to start (first week=1, last week=5)i0
(Optional) Weekday to starts1
(Optional) Month to starts2
(Optional) HH:MM Time to starts3
(Optional) Week number to end (first week=1, last week=5)i1
(Optional) Weekday to ends4
(Optional) Month to ends5
(Optional) HH:MM Time to ends6
(Optional) Offset to add in minutesi2
Configure time zonetimezone
Name of time zone, such as PST, MST, CST, EST, etc..s7
Hours offset from UTCi3
Minutes offset from UTCi4
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)751
C Commandsclock summer
Page 896
clock sync-interval[no] clock sync-interval <intv>
Syntax Description
(Optional) Negate a command or set its defaultsno
Clockclock
sync-interval in secondssync-interval
intervalintv
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)752
C Commandsclock sync-interval
Page 897
cluster-id[no] cluster-id { <ip-cluster-id> | <int-cluster-id> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Route Reflector Cluster-IDcluster-id
Cluster-id as an IP addressip-cluster-id
Cluster-id as a 32 bit quantityint-cluster-id
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)753
C Commandscluster-id
Page 898
collect[no] collect { ingress queue depth | ingress queue drops }
Syntax Description
Stats type to be configuredcollect
Ingress counteringress
Queue statisticsqueue
Depthdepth
Dropsdrops
Command Mode
• /exec/configure/config-ssx-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)754
C Commandscollect
Page 899
collect{ [ no ] collect { port-id | hop-latency | queue-occupancy | queue-congestion | ingress-timestamp |egress-timestamp | egress-tx-util } }
Syntax Description
Specify a collect fieldcollect
Port Identifierport-id
Latency in this hophop-latency
Queue occupancyqueue-occupancy
Queue congestionqueue-congestion
Timestamp at ingressingress-timestamp
Timestamp at egressegress-timestamp
Egress utilizationegress-tx-util
Command Mode
• /exec/configure/config-int-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)755
C Commandscollect
Page 900
collect[no] collect { egress queue depth | egress queue drops | egress queue microburst | egress queue peak }
Syntax Description
Stats type to be configuredcollect
Egress counteregress
Queue statisticsqueue
Depthdepth
Dropsdrops
Microburst recordsmicroburst
Buffer peak counterspeak
Command Mode
• /exec/configure/config-ssx-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)756
C Commandscollect
Page 901
collect[no] collect { egress buffer depth }
Syntax Description
Stats type to be configuredcollect
Egress counteregress
Buffer statisticsbuffer
Depthdepth
Command Mode
• /exec/configure/config-ssx-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)757
C Commandscollect
Page 902
collect[no] collect { egress pool-group depth }
Syntax Description
Stats type to be configuredcollect
Egress counteregress
Pool-group statisticspool-group
Depthdepth
Command Mode
• /exec/configure/config-ssx-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)758
C Commandscollect
Page 903
collect[no] collect { ethernet counters }
Syntax Description
Stats type to be configuredcollect
Ethernet counterethernet
Ethernet counterscounters
Command Mode
• /exec/configure/config-ssx-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)759
C Commandscollect
Page 904
collect counter bytes[no] collect counter { bytes | packets } [ long ]
Syntax Description
Specify a non-key fieldcollect
Counters to collectcounter
Total number of bytesbytes
Total number of packetspackets
(Optional) Long counter (64 bits)long
Command Mode
• /exec/configure/nfm-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)760
C Commandscollect counter bytes
Page 905
collect ip version[no] collect ip version
Syntax Description
Specify a non-key fieldcollect
IP attributesip
IPv4 or IPv6version
Command Mode
• /exec/configure/nfm-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)761
C Commandscollect ip version
Page 906
collect timestamp sys-uptime first[no] collect timestamp sys-uptime { first | last }
Syntax Description
Specify a non-key fieldcollect
Timestamp fieldstimestamp
System uptimesys-uptime
Time the first packet was seenfirst
Time the most recent packet was seenlast
Command Mode
• /exec/configure/nfm-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)762
C Commandscollect timestamp sys-uptime first
Page 907
collect transport tcp flags[no] collect transport tcp flags
Syntax Description
Specify a non-key fieldcollect
Transport layer fieldstransport
TCP layer fieldstcp
TCP flagsflags
Command Mode
• /exec/configure/nfm-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)763
C Commandscollect transport tcp flags
Page 908
color{ no color | color <color> }
Syntax Description
Negate a command or set its defaultsno
Policy Colorcolor
Policy Colorcolor
Command Mode
• /exec/configure/sr/te/pol
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)764
C Commandscolor
Page 909
commitcommit
Syntax Description
commit plb sessioncommit
Command Mode
• /exec/configure/plb-session-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)765
C Commandscommit
Page 910
commitcommit
Syntax Description
Commit the current configuration sessioncommit
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)766
C Commandscommit
Page 911
commitcommit
Syntax Description
commit itd sessioncommit
Command Mode
• /exec/configure/itd-session-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)767
C Commandscommit
Page 912
commit verbosecommit verbose
Syntax Description
Commit the current configuration sessioncommit
Commit the current configuration session with more detailsverbose
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)768
C Commandscommit verbose
Page 913
compress-bitfields ipv6 multicast[no] compress-bitfields ipv6 multicast
Syntax Description
(Optional) Negate a command or set its defaultsno
Compress bitfields for improved memory utilizationcompress-bitfields
Use for IPv6 multicastipv6
Use compressed bitfields for M6RIB and PIM6multicast
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)769
C Commandscompress-bitfields ipv6 multicast
Page 914
compress-bitfields ipv6 multicast[no] compress-bitfields ipv6 multicast
Syntax Description
(Optional) Negate a command or set its defaultsno
Compress bitfield for improved memory utilizationcompress-bitfields
Use for IPv6 multicastipv6
Use compressed bitfields for M6RIB and PIMmulticast
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)770
C Commandscompress-bitfields ipv6 multicast
Page 915
compress-bitfields multicast[no] compress-bitfields [ ipv4 ] multicast
Syntax Description
(Optional) Negate a command or set its defaultsno
Compress bitfield for improved memory utilizationcompress-bitfields
(Optional) Use for IPv4 multicastipv4
Use compressed bitfields for MRIB and PIMmulticast
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)771
C Commandscompress-bitfields multicast
Page 916
conf-offset[no] conf-offset <offset>
Syntax Description
Configure Confidentiality offsetconf-offset
Confidentiality offset optionsoffset
Command Mode
• /exec/configure/macsec-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)772
C Commandsconf-offset
Page 917
confederation identifier[no] confederation identifier <confed-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
AS confederation parametersconfederation
Set routing domain confederation ASidentifier
AS numberconfed-id
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)773
C Commandsconfederation identifier
Page 918
confederation peers[no] confederation peers <confed-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
AS confederation parametersconfederation
Peer ASs in BGP confederationpeers
AS numberconfed-id
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)774
C Commandsconfederation peers
Page 919
config-source controller[no] config-source controller
Syntax Description
(Optional) Negate a command or set its defaultsno
Configuration source for this NVE interface. Defaults to CLIconfig-source
Controllercontroller
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)775
C Commandsconfig-source controller
Page 920
configureconfigure [ terminal ]
Syntax Description
Enter configuration modeconfigure
(Optional) Configure the system from terminal inputterminal
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)776
C Commandsconfigure
Page 921
configure config-template on substitute[no] configure config-template <name> { on-vrf-create | on-vrf-delete } substitute <match_replace>
Syntax Description
(Optional) Negate a command or set its defaultsno
Enter configuration modeconfigure
Configuration-templateconfig-template
Configuration-template namename
Configuration-template for create actionon-vrf-create
Configuration-template for delete actionon-vrf-delete
Configuration-template substitutesubstitute
string in match:replace format for substitutionmatch_replace
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)777
C Commandsconfigure config-template on substitute
Page 922
configure maintenance profile normal[no] configure maintenance profile { normal-mode | maintenance-mode }
Syntax Description
(Optional) Negate a command or set its defaultsno
Enter configuration modeconfigure
maintenance profile modemaintenance
maintenance profileprofile
Normal mode profilenormal-mode
Maintenance mode profilemaintenance-mode
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)778
C Commandsconfigure maintenance profile normal
Page 923
configure profile[no] configure profile <all_conf_profile_name> [ type admin ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enter configuration modeconfigure
Configure profileprofile
Enter the name of the configure profileall_conf_profile_name
(Optional) config profile typetype
(Optional) config profile admin typeadmin
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)779
C Commandsconfigure profile
Page 924
configure replaceconfigure replace { <uri_local> | <uri_remote> [ source-interface <intf> | vrf <vrf-known-name> ] } [ [ [verbose ] [ debug | stop-at-first-failure ] [ commit-timeout <time> ] [ non-interactive ] ] | show-patch ]
Syntax Description
Configure the boxconfigure
Perform a replace of the running-configreplace
Configuration file to useuri_local
Configuration file to useuri_remote
(Optional) Select source interfacesource-interface
(Optional)intf
(Optional) Display per-VRF informationvrf
(Optional) Show the logs of operationverbose
(Optional) Show the patch to be appliedshow-patch
(Optional) Skip errors and proceed with rollbackdebug
(Optional) Stop config-replace at the first errorstop-at-first-failure
(Optional) specify config replace commit timeout valuecommit-timeout
(Optional) Timeout in secondstime
(Optional) No user prompt in maintenance modenon-interactive
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)780
C Commandsconfigure replace
Page 925
configure replace abortconfigure replace abort
Syntax Description
Configure the boxconfigure
Perform a replace of the running-configreplace
Aborting config replace operationabort
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)781
C Commandsconfigure replace abort
Page 926
configure replace commitconfigure replace commit
Syntax Description
Configure the boxconfigure
Perform a replace of the running-configreplace
Commit config replace operationcommit
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)782
C Commandsconfigure replace commit
Page 927
configure sessionconfigure session <s0>
Syntax Description
Enter configuration modeconfigure
Configure the system in a sessionsession
Enter the name of the sessions0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)783
C Commandsconfigure session
Page 928
configure syncconfigure sync
Syntax Description
Enter configuration modeconfigure
Configure the system in config-sync modesync
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)784
C Commandsconfigure sync
Page 929
congestion-control dctcp ecn-threshold bytes[no] congestion-control dctcp ecn-threshold <threshold> { bytes }
Syntax Description
(Optional) Negate a command or set its defaultsno
Congestion Control Protocolcongestion-control
Data Center TCPdctcp
Explicit Congestion Notification - thresholdecn-threshold
Threshold in bytesthreshold
Bytesbytes
Command Mode
• /exec/configure/policy-map/type/uf/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)785
C Commandscongestion-control dctcp ecn-threshold bytes
Page 930
congestion-control ecn[no] congestion-control ecn
Syntax Description
(Optional) Negate a command or set its defaultsno
Congestion Control Protocolcongestion-control
Enable ECN protocolecn
Command Mode
• /exec/configure/policy-map/type/uf/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)786
C Commandscongestion-control ecn
Page 931
congestion-control random-detect[no] congestion-control random-detect { [ threshold { burst-optimized | mesh-optimized } ] | {minimum-threshold <min-thresh> [ packets | bytes | kbytes | mbytes ] maximum-threshold <max-thresh> [packets1 | bytes1 | kbytes1 | mbytes1 ] drop-probability <drop-prob> } } { [ ecn ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Congestion Control Protocolcongestion-control
Enable WRED protocolrandom-detect
(Optional) Thresholdthreshold
Minimum Thresholdminimum-threshold
Maximum Thresholdmaximum-threshold
(Optional) Threshold optimized for bursty trafficburst-optimized
(Optional) Threshold optimized for mesh trafficmesh-optimized
Drop Probability at Maximum Thresholddrop-probability
Drop Probability Valuedrop-prob
(Optional) Packetspackets
(Optional) Bytesbytes
(Optional) Kilo Byteskbytes
(Optional) Mega Bytesmbytes
(Optional) Packetspackets1
(Optional) Bytesbytes1
(Optional) Kilo Byteskbytes1
(Optional) Mega Bytesmbytes1
(Optional) Explicit Congestion Notificationecn
Command Mode
• /exec/configure/policy-map/type/uf/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)787
C Commandscongestion-control random-detect
Page 932
congestion-control random-detect forward-nonecn[no] congestion-control random-detect forward-nonecn
Syntax Description
(Optional) Negate the commandno
Congestion control protocolcongestion-control
Enable WRED protocolrandom-detect
Forward non ECN capable traffic without WRED droppingforward-nonecn
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)788
C Commandscongestion-control random-detect forward-nonecn
Page 933
congestion-control random-detect global-bufferminimum-threshold maximum-threshold
[no] congestion-control random-detect global-buffer minimum-threshold { <min-thresh> [ packets | bytes |kbytes | mbytes ] } maximum-threshold { <max-thresh> [ packets1 | bytes1 | kbytes1 | mbytes1 ] }
Syntax Description
(Optional) Negate the commandno
Congestion control protocolcongestion-control
Enable WRED protocolrandom-detect
global buffer thresholdglobal-buffer
Specify minimum threshold for WREDminimum-threshold
Minimum threshold valuemin-thresh
Specify maximum threshold for WREDmaximum-threshold
Maximum threshold valuemax-thresh
(Optional) Packetspackets
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Packetspackets1
(Optional) Bytesbytes1
(Optional) Kilo Byteskbytes1
(Optional) Mega Bytesmbytes1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)789
C Commandscongestion-control random-detect global-buffer minimum-threshold maximum-threshold
Page 934
congestion-control tail-drop[no] congestion-control tail-drop [ threshold { burst-optimized | mesh-optimized } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Congestion Control Protocolcongestion-control
Enable Tail-Droptail-drop
(Optional) Thresholdthreshold
(Optional) Threshold optimized for bursty trafficburst-optimized
(Optional) Threshold optimized for mesh trafficmesh-optimized
Command Mode
• /exec/configure/policy-map/type/uf/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)790
C Commandscongestion-control tail-drop
Page 935
connect[no] connect
Syntax Description
(Optional) Negate a command or set its defaultsno
Connect to remote hostconnect
Command Mode
• /exec/configure/vmt-conn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)791
C Commandsconnect
Page 936
connected-prefix-sid-map[no] connected-prefix-sid-map
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure connected prefix Segment Identifier mappingsconnected-prefix-sid-map
Command Mode
• /exec/configure/config-sr-mpls
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)792
C Commandsconnected-prefix-sid-map
Page 937
continue{ continue <value> } | { no continue [ <value> ] }
Syntax Description
Negate a command or set its defaultsno
Continue on a different entry within the route-mapcontinue
Route-map entry sequence numbervalue
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)793
C Commandscontinue
Page 938
contract-id{ contract-id <s0> | no contract-id }
Syntax Description
Negate a command or set its defaultsno
Service contract id of the customercontract-id
Provide contract number (as specified in the service agreement)s0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)794
C Commandscontract-id
Page 939
control-planecontrol-plane
Syntax Description
Enter to control-plane sub-modecontrol-plane
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)795
C Commandscontrol-plane
Page 940
control-plane dynamiccontrol-plane dynamic
Syntax Description
Enter to control-plane sub-modecontrol-plane
dynamic modedynamic
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)796
C Commandscontrol-plane dynamic
Page 941
control vlan[no] control vlan <vlan-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure PLB control vlancontrol
control vlanvlan
vlan idvlan-id
Command Mode
• /exec/configure/plb-inout
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)797
C Commandscontrol vlan
Page 942
control vlan[no] control vlan <vlan-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD control vlancontrol
control vlanvlan
Control vlan idvlan-id
Command Mode
• /exec/configure/itd-inout
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)798
C Commandscontrol vlan
Page 943
controller-credentials username password 0[no] controller-credentials username <user> password { 0 <clear> | 7 <encrypted> }
Syntax Description
(Optional) Negate a command or set its defaultsno
NBM Controller login credentialscontroller-credentials
User IDusername
Enter user IDuser
Passwordpassword
Password that follows should be in clear text0
Password in clear textclear
Password that follows should be encrypted text7
Encrypted passwordencrypted
Command Mode
• /exec/configure/nbm-controller
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)799
C Commandscontroller-credentials username password 0
Page 944
controller description{ controller description <ctrlr-desc> | no controller description }
Syntax Description
Negate a command or set its defaultsno
Controller commandcontroller
Controller descriptiondescription
String description of the controllerctrlr-desc
Command Mode
• /exec/configure/controller-type
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)800
C Commandscontroller description
Page 945
controller ip vrf[no] controller ip <cntlr-ip> vrf { <vrf-name> | <vrf-known-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Controllercontroller
IP Addressip
IP Address of Controllercntlr-ip
vrf contextvrf
VRF namevrf-name
Known VRF namevrf-known-name
Command Mode
• /exec/configure/nbm-controller
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)801
C Commandscontroller ip vrf
Page 946
controller ipv4[no] controller ipv4 <ipv4> [ port <tcpport> ] [ vrf { <vrf-name> | <vrf-known-name> } ] [ security { none |tls } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
OpenFlow controller to usecontroller
Controller ipv4 address (A.B.C.D)ipv4
IP address (A.B.C.D)ipv4
(Optional) Controller TCP port (default is 6653)port
(Optional) TCP port number (default port is 6653)tcpport
(Optional) Controller VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Set security protocolsecurity
(Optional) Disable security protocolnone
(Optional) Enable security protocoltls
Command Mode
• /exec/configure/openflow/switch/sub-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)802
C Commandscontroller ipv4
Page 947
controller ipv4[no] controller ipv4 <ipv4> [ port <tcpport> ] [ vrf { <vrf-name> | <vrf-known-name> } ] [ security { none |tls } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
OpenFlow controller to usecontroller
Controller ipv4 address (A.B.C.D)ipv4
IP address (A.B.C.D)ipv4
(Optional) Controller TCP port (default is 6653)port
(Optional) TCP port number (default port is 6653)tcpport
(Optional) Controller VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Set security protocolsecurity
(Optional) Disable security protocolnone
(Optional) Enable security protocoltls
Command Mode
• /exec/configure/openflow/switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)803
C Commandscontroller ipv4
Page 948
controller type l2 identifier[no] controller type { l2-vxlan | vxlan } identifier <controller-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Controller commandcontroller
Controller typetype
l2-vxlanl2-vxlan
vxlanvxlan
Controller identifieridentifier
Controller id valuecontroller-id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)804
C Commandscontroller type l2 identifier
Page 949
copp copy profile prefixcopp copy profile <profile_type> { prefix | suffix } <user_string>
Syntax Description
Control-Plane Policingcopp
Make a copy of the CoPP Profilecopy
CoPP Profileprofile
CoPP Profile Typesprofile_type
prefix for the copied policyprefix
suffix for the copied policysuffix
Enter prefix/suffix for the copied policyuser_string
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)805
C Commandscopp copy profile prefix
Page 950
copp distributed-policing enable[no] copp distributed-policing enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Control-Plane Policingcopp
distributed policerdistributed-policing
enable distributed policingenable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)806
C Commandscopp distributed-policing enable
Page 951
copp profilecopp profile <profile_type>
Syntax Description
Control-Plane Policingcopp
CoPP Profileprofile
CoPP Profile Typesprofile_type
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)807
C Commandscopp profile
Page 952
copp profile[no] copp profile [ <profile_type> ]
Syntax Description
Negate a command or set its defaultsno
Control-Plane Policingcopp
CoPP Profileprofile
(Optional) CoPP Profile Typesprofile_type
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)808
C Commandscopp profile
Page 953
copp rate-limit disable[no] copp rate-limit disable
Syntax Description
(Optional) Negate a command or set its defaultsno
coppcopp
rate-limitrate-limit
Disable rate-limit on CoPP queuesdisable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)809
C Commandscopp rate-limit disable
Page 954
copycopy { { <src_local> { <dest_remote> [ source-interface <intf> | vrf <vrf-known-name> ] } } | { <src_remote>{ <dest_local> [ compact ] | running-config [ echo-commands ] [ stop-at-first-failure ] | startup-config } } [source-interface <intf> | vrf <vrf-known-name> ] | { <src_core> { <dest_remote> [ source-interface <intf> |vrf <vrf-known-name> ] } } | { running-config-src { <dest_remote> [ source-interface <intf> | vrf<vrf-known-name> ] } } | { startup-config-src { <dest_remote> [ source-interface <intf> | vrf<vrf-known-name> ] } } }
Syntax Description
Syntax Description Copy from one file to anothercopy
Select source filesystemsrc_local
Select source filesystemsrc_core
Select destination filesystemdest_local
Select destination filesystemdest_remote
Select source filesystemsrc_remote
(Optional) Display per-VRF informationvrf
(Optional) Select source interfacesource-interface
(Optional)intf
(Optional) Known VRF namevrf-known-name
(Optional) Compacting NXOS NBI image using scpcompact
Copy from source to running configurationrunning-config
Copy running configuration to destinationrunning-config-src
Copy from source to startup configurationstartup-config
Copy startup configuration to destinationstartup-config-src
(Optional) Echo the commands before applying them (to correlate errors)echo-commands
(Optional) Stop at first errorstop-at-first-failure
Command Mode
• /exec
Usage Guidelines
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)810
C Commandscopy
Page 955
When a source or destination URI contains a reserved character such as '!' or '#', the reserved character mustbe entered as its percent-encoded ascii value, as described in RFC 3986. For example, the URI!pa##[email protected] must be entered as %21pa%23%[email protected] . In this example, the reservedcharacters '!' (ascii 0x21) and '#' (ascii 0x23) are represented as '%21' and '%23'.
Note
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)811
C Commandscopy
Page 956
copycopy { { <src_local> { <dest_local> | running-config [ echo-commands ] [ stop-at-first-failure ] | startup-config| scheduled-config } } | { <src_core> <dest_local_core> } | { running-config-src { startup-config [ fabric ] |<dest_local_config> } } | { startup-config-src { running-config [ echo-commands ] [ stop-at-first-failure ] |<dest_local_config> } } | { switch-profile-cfg <dest_local_config> } }
Syntax Description
Syntax Description Copy from one file to anothercopy
Select source filesystemsrc_local
Select source filesystemsrc_core
Select destination filesystemdest_local
Select destination filesystemdest_local_core
Select destination filesystemdest_local_config
Copy from source to running configurationrunning-config
Copy running configuration to destinationrunning-config-src
Copy from source to startup configurationstartup-config
Copy startup configuration to destinationstartup-config-src
Schedule configuration at the specified source to be applied at next switch reloadscheduled-config
Copy switch profile running configuration to destinationswitch-profile-cfg
(Optional) Echo the commands before applying them (to correlate errors)echo-commands
(Optional) Stop at first errorstop-at-first-failure
(Optional) Copy from source to fabric startup configurationfabric
Command Mode
• /exec
Usage Guidelines
When a source or destination URI contains a reserved character such as '!' or '#', the reserved character mustbe entered as its percent-encoded ascii value, as described in RFC 3986. For example, the URI!pa##[email protected] must be entered as %21pa%23%[email protected] . In this example, the reservedcharacters '!' (ascii 0x21) and '#' (ascii 0x23) are represented as '%21' and '%23'.
Note
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)812
C Commandscopy
Page 957
copy licensescopy licenses <uri0>
Syntax Description
Copy from one file to anothercopy
Backup license fileslicenses
Specify URL (with .tar extension) for backing up license filesuri0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)813
C Commandscopy licenses
Page 958
copy licensescopy licenses <uri0>
Syntax Description
Copy from one file to anothercopy
Backup license fileslicenses
Specify URL (with .tar extension) for backing up license filesuri0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)814
C Commandscopy licenses
Page 959
copy recursivecopy <source> <destination> recursive [ vrf <vrf-known-name> ]
Syntax Description
Syntax Description Copy from one file to anothercopy
Recursively copy files and foldersrecursive
Select source filesystemsource
Select destination filesystemdestination
(Optional) Display per-VRF informationvrf
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Usage Guidelines
When a source or destination URI contains a reserved character such as '!' or '#', the reserved character mustbe entered as its percent-encoded ascii value, as described in RFC 3986. For example, the URI!pa##[email protected] must be entered as %21pa%23%[email protected] . In this example, the reservedcharacters '!' (ascii 0x21) and '#' (ascii 0x23) are represented as '%21' and '%23'.
Note
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)815
C Commandscopy recursive
Page 960
copy running vdc-allcopy { running-config-src { <dest_remote> [ source-interface <intf> | vrf <vrf-known-name> ] } |startup-config-src { <dest_remote> [ source-interface <intf> | vrf <vrf-known-name> ] } } vdc-all
Syntax Description
Syntax Description Copy from one file to anothercopy
Select destination filesystemdest_remote
(Optional) Display per-VRF informationvrf
(Optional) Known VRF namevrf-known-name
(Optional) Select source interfacesource-interface
(Optional)intf
Copy running configuration to destinationrunning-config-src
Copy startup configuration to destinationstartup-config-src
Perform copy for all vdcsvdc-all
Command Mode
• /exec
Usage Guidelines
When a source or destination URI contains a reserved character such as '!' or '#', the reserved character mustbe entered as its percent-encoded ascii value, as described in RFC 3986. For example, the URI!pa##[email protected] must be entered as %21pa%23%[email protected] . In this example, the reservedcharacters '!' (ascii 0x21) and '#' (ascii 0x23) are represented as '%21' and '%23'.
Note
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)816
C Commandscopy running vdc-all
Page 961
copy vdc-allcopy { running-config-src { startup-config | <dest_local_config> } | startup-config-src { running-config |<dest_local_config> } } vdc-all
Syntax Description
Syntax Description Copy from one file to anothercopy
Select destination filesystemdest_local_config
Copy running configuration to destinationrunning-config-src
Copy from source to startup configurationstartup-config
Copy from source to running configurationrunning-config
Copy startup configuration to destinationstartup-config-src
Perform copy for all vdcsvdc-all
Command Mode
• /exec
Usage Guidelines
When a source or destination URI contains a reserved character such as '!' or '#', the reserved character mustbe entered as its percent-encoded ascii value, as described in RFC 3986. For example, the URI!pa##[email protected] must be entered as %21pa%23%[email protected] . In this example, the reservedcharacters '!' (ascii 0x21) and '#' (ascii 0x23) are represented as '%21' and '%23'.
Note
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)817
C Commandscopy vdc-all
Page 962
core-on-no-memory[no] core-on-no-memory
Syntax Description
(Optional) Negate a command or set its defaultsno
Generate core dump on memory allocation failurecore-on-no-memory
Command Mode
• /exec/configure/router-ospf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)818
C Commandscore-on-no-memory
Page 963
core-on-no-memory[no] core-on-no-memory
Syntax Description
(Optional) Negate a command or set its defaultsno
Generate core dump on memory allocation failurecore-on-no-memory
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)819
C Commandscore-on-no-memory
Page 964
cost{ cost <cost> } | { no cost [ <cost> ] }
Syntax Description
Negate a command or set its defaultsno
Cost associated with interfacecost
Cost valuecost
Command Mode
• /exec/configure/router-ospf/vrf/router-ospf-slink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)820
C Commandscost
Page 965
count[no] count <cap-count>
Syntax Description
(Optional) Negate the commandno
Configure Captured Transactions countcount
Number of Captured Transactionscap-count
Command Mode
• /exec/configure/pkt-drop
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)821
C Commandscount
Page 966
count| count
Syntax Description
Pipe command output to filter|
Count number of linescount
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)822
C Commandscount
Page 967
counter name value opcounter name <counter-name> value <counter-value> op <op-val>
Syntax Description
Specify the name of the countercounter
Specify the name of the countername
Name of the countercounter-name
Specify the value to be applied to the countervalue
Enter the valuecounter-value
Specify the operator to be appliedop
Enter the value of the operatorop-val
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)823
C Commandscounter name value op
Page 968
crypto ca authenticate[no] crypto ca authenticate <s0> [ accept ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Set crypto settingscrypto
Configure certificate authority related informationca
Authenticate the certificate authority certificateauthenticate
trustpoint labels0
(Optional) accept the certificate automaticallyaccept
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)824
C Commandscrypto ca authenticate
Page 969
crypto ca crl request[no] crypto ca crl request <s0> <uri0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set crypto settingscrypto
Configure certificate authority related informationca
import certificate revocation listcrl
import certificate revocation listrequest
trustpoint labels0
Specify source file nameuri0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)825
C Commandscrypto ca crl request
Page 970
crypto ca enroll[no] crypto ca enroll <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set crypto settingscrypto
Configure certificate authority related informationca
Create certificate requestenroll
trustpoint labels0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)826
C Commandscrypto ca enroll
Page 971
crypto ca export pkcs12[no] crypto ca export <s0> pkcs12 <uri0> <s1>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set crypto settingscrypto
Configure certificate authority related informationca
export rsa private key and certificates in pkcs#12export
trustpoint labels0
destination file urlpkcs12
Specify destination file nameuri0
passphrase to encrypt the private keys1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)827
C Commandscrypto ca export pkcs12
Page 972
crypto ca import certificate[no] crypto ca import <s0> certificate
Syntax Description
(Optional) Negate a command or set its defaultsno
Set crypto settingscrypto
Configure certificate authority related informationca
import the certificate or keyimport
trustpoint labels0
import the certificatecertificate
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)828
C Commandscrypto ca import certificate
Page 973
crypto ca import pkcs12crypto ca import <s0> pkcs12 <uri0> <s1>
Syntax Description
Set crypto settingscrypto
Configure certificate authority related informationca
import the certificate or keyimport
trustpoint labels0
source file urlpkcs12
source file urluri0
passphrase to decrypt the private keys1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)829
C Commandscrypto ca import pkcs12
Page 974
crypto ca lookup[no] crypto ca lookup { remote | local | both }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set crypto settingscrypto
Configure certificate authority related informationca
Choose the certstore for authenticationlookup
Use remote certstoreremote
Use local certstorelocal
Use both local and remote certstoreboth
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)830
C Commandscrypto ca lookup
Page 975
crypto ca remote ldap[no] crypto ca remote ldap { server-group <s0> | [ crl-refresh-time <i0> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set crypto settingscrypto
Configure certificate authority related informationca
Use ca from remote certstoreremote
Ldap certstoreldap
(Optional) Configure refresh-time to fetch crl from remote certstorecrl-refresh-time
(Optional) Refresh time value in hours. A value of 0 will now run therefresh routine once.
i0
Ldap server groupserver-group
Ldap server group names0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)831
C Commandscrypto ca remote ldap
Page 976
crypto ca test verify[no] crypto ca test verify <uri0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set crypto settingscrypto
Configure certificate authority related informationca
certificate teststest
verify the certificateverify
Specify certificate file nameuri0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)832
C Commandscrypto ca test verify
Page 977
crypto ca trustpoint[no] crypto ca trustpoint <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set crypto settingscrypto
Configure certificate authority related informationca
Configure trustpoint certificate authoritytrustpoint
trustpoint labels0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)833
C Commandscrypto ca trustpoint
Page 978
crypto ca trustpool import urlcrypto ca trustpool import url <source_uri>
Syntax Description
Set crypto settingscrypto
Configure certificate authority related informationca
Configure trustpool related informationtrustpool
Configure import of trustpoolimport
Configure URL from which trustpool will be importedurl
Select source URLsource_uri
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)834
C Commandscrypto ca trustpool import url
Page 979
crypto ca trustpool import url cleancrypto ca trustpool import url clean
Syntax Description
Set crypto settingscrypto
Configure certificate authority related informationca
Configure trustpool related informationtrustpool
Configure import of trustpoolimport
URL from which trustpool will be importedurl
delete the contents of the trustpoolclean
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)835
C Commandscrypto ca trustpool import url clean
Page 980
crypto ca trustpool policycrypto ca trustpool policy
Syntax Description
Set crypto settingscrypto
Configure certificate authority related informationca
Configure trustpool related informationtrustpool
Configure trustpool policypolicy
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)836
C Commandscrypto ca trustpool policy
Page 981
crypto cert ssh-authorize[no] crypto cert ssh-authorize [ <s0> map <s1> [ <s2> ] | default map <s3> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure crypto settingscrypto
Configure certificate maping filter settingscert
Configure mapping filter for sshssh-authorize
(Optional) Issuer name of the certificates0
(Optional) Mapping filter to be appliedmap
(Optional) Name of the mapping filter which is already configureds1
(Optional) Name of the mapping filter which is already configureds2
(Optional) Default map for ssh authorizationdefault
(Optional) Name of the default mapping filter which is alreadyconfigured
s3
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)837
C Commandscrypto cert ssh-authorize
Page 982
crypto certificatemap mapname[no] crypto certificatemap mapname <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set crypto settingscrypto
Configure certificatemap filterscertificatemap
Create a new filter mapmapname
Name of the filter maps0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)838
C Commandscrypto certificatemap mapname
Page 983
crypto key generate rsa[no] crypto key generate rsa [ { [ exportable ] [ modulus <i0> ] | [ label <s0> ] [ [ exportable ] [ modulus1<i1> ] ] | modulus2 <i2> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Set crypto settingscrypto
Configure key pair related informationkey
Configure key pair generation related informationgenerate
Configure rsa key pair generation related informationrsa
(Optional) key-pair is exportableexportable
(Optional) key-pair sizemodulus
(Optional) key-pair sizei0
(Optional) key-pair labellabel
(Optional) key-pair labels0
(Optional) key-pair is exportableexportable
(Optional) key-pair sizemodulus1
(Optional) key-pair sizei1
(Optional) key-pair sizemodulus2
(Optional) key-pair sizei2
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)839
C Commandscrypto key generate rsa
Page 984
crypto key param rsa label modulus[no] crypto key param rsa label <s0> modulus <i0> [ exportable ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Set crypto settingscrypto
Configure key pair related informationkey
Configure key pair related informationparam
Configure rsa key pair related informationrsa
key-pair labellabel
key-pair labels0
key-pair sizemodulus
key-pair sizei0
(Optional) key-pair is exportableexportable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)840
C Commandscrypto key param rsa label modulus
Page 985
crypto key zeroize rsa[no] crypto key zeroize rsa <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set crypto settingscrypto
Configure key pair related informationkey
Delete key-pairzeroize
Delete rsa key-pairrsa
key-pair labels0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)841
C Commandscrypto key zeroize rsa
Page 986
cryptographic-algorithm[no] cryptographic-algorithm <algo>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set cryptographic-algorithm to be usedcryptographic-algorithm
Crytographic-algorithmalgo
Command Mode
• /exec/configure/keychain-key
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)842
C Commandscryptographic-algorithm
Page 987
customer-id{ customer-id <s0> | no customer-id }
Syntax Description
Negate a command or set its defaultsno
customer idcustomer-id
Provide customer id (as specified in the service agreement)s0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)843
C Commandscustomer-id
Page 988
cut| cut { -b <bytes> | -c <chars> | -f <fields> | -d <delim> | -s | --help } +
Syntax Description
Pipe command output to filter|
Print selected parts of lines.cut
output only these bytes-b
output only these characters-c
specify other field delimiter (default is TAB).-d
output only these fields also print any line that contains no delimitercharacter, unless the -s option is specified
-f
do not print lines not containing delimiters-s
{n|n-|n-m|-m} N-th byte, N to end of line, N to M, start of line to Nbytes
{n|n-|n-m|-m} N-th char, N to end of line, N to M, start of line to Nchars
{n|n-|n-m|-m} N-th field, N to end of line, N to M, start of line to Nfields
field separator char, TAB is default, use ' ' for spacedelim
print help of underlying unix command--help
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)844
C Commandscut
Page 989
D Commands
• dampen-igp-metric, on page 851• dampening, on page 852• dampening, on page 853• dampening, on page 854• data-pattern, on page 855• data-pattern pad, on page 856• data-source, on page 857• database-mapping, on page 858• databits, on page 859• databits, on page 860• datapath-id, on page 861• datapath-id, on page 862• db-jid, on page 863• db-security user password, on page 864• db-table, on page 865• dead-interval, on page 866• dead-interval, on page 867• dead-interval, on page 868• deadtime, on page 869• deadtime, on page 870• deadtime, on page 871• default-information originate, on page 872• default-information originate, on page 873• default-information originate, on page 874• default-information originate, on page 875• default-information originate, on page 876• default-information originate, on page 877• default-information originate always rd route-target, on page 878• default-metric, on page 879• default-metric, on page 880• default-metric, on page 881• default-metric, on page 882• default-metric, on page 883
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)845
Page 990
• default-miss, on page 884• default-originate, on page 885• default echo revision, on page 886• default permit, on page 887• default permit, on page 888• default permit, on page 889• define, on page 890• delay-restore time, on page 891• delay, on page 892• delay, on page 893• delay, on page 894• delay peer-link, on page 895• delay restore, on page 896• delay restore interface-vlan, on page 897• delay restore orphan-port, on page 898• delay up, on page 899• delete, on page 900• delete ca-certificate, on page 901• delete certificate, on page 902• delete crl, on page 903• demand-circuit, on page 904• depth, on page 905• depth, on page 906• description, on page 907• description, on page 908• description, on page 909• description, on page 910• description, on page 911• description, on page 912• description, on page 913• description, on page 914• description, on page 915• description, on page 916• description, on page 917• description, on page 918• description, on page 919• description, on page 920• description, on page 921• description, on page 922• description, on page 923• description, on page 924• description, on page 925• description, on page 926• description, on page 927• description, on page 928• description, on page 929
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)846
D Commands
Page 991
• description, on page 930• description, on page 931• description, on page 932• description, on page 933• description, on page 934• description, on page 935• description, on page 936• description, on page 937• description, on page 938• description, on page 939• description, on page 940• description, on page 941• description, on page 942• description, on page 943• description, on page 944• description, on page 945• description, on page 946• description, on page 947• description, on page 948• description, on page 949• description, on page 950• description, on page 951• description, on page 952• description description, on page 953• dest-ipaddr, on page 954• dest-ipaddr, on page 955• dest-port, on page 956• dest, on page 957• destination-group, on page 958• destination-profile, on page 959• destination-profile, on page 960• destination-profile CiscoTAC-1 alert-group, on page 961• destination-profile CiscoTAC-1 email-addr, on page 962• destination-profile CiscoTAC-1 http, on page 963• destination-profile CiscoTAC-1 message-level, on page 964• destination-profile CiscoTAC-1 message-size, on page 965• destination-profile CiscoTAC-1 transport-method http, on page 966• destination-profile CiscoTAC-1 transport-method email, on page 967• destination-profile alert-group, on page 968• destination-profile email-addr, on page 969• destination-profile format, on page 970• destination-profile full-txt-destination alert-group, on page 971• destination-profile full-txt-destination email-addr, on page 972• destination-profile full-txt-destination http, on page 973• destination-profile full-txt-destination message-size, on page 974• destination-profile full-txt-destination message-level, on page 975
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)847
D Commands
Page 992
• destination-profile full-txt-destination transport-method http, on page 976• destination-profile full-txt-destination transport-method email, on page 977• destination-profile http, on page 978• destination-profile message-level, on page 979• destination-profile message-size, on page 980• destination-profile short-txt-destination alert-group, on page 981• destination-profile short-txt-destination email-addr, on page 982• destination-profile short-txt-destination http, on page 983• destination-profile short-txt-destination message-size, on page 984• destination-profile short-txt-destination message-level, on page 985• destination-profile short-txt-destination transport-method http, on page 986• destination-profile short-txt-destination transport-method email, on page 987• destination-profile transport-method email, on page 988• destination-profile transport-method http, on page 989• destination-sup interface, on page 990• destination, on page 991• destination1 interface, on page 992• destination, on page 993• destination, on page 994• destination, on page 995• destination, on page 996• destination, on page 997• destination filter ip, on page 998• destination filter ip any any, on page 999• destination group, on page 1000• destination interface, on page 1001• destination ip, on page 1002• device-group, on page 1003• device-group, on page 1004• device-role, on page 1005• device-role, on page 1006• device-role, on page 1007• dfe-tuning-delay, on page 1008• diagnostic bootup level, on page 1009• diagnostic bootup level bypass, on page 1010• diagnostic clear result module all diagnostic clear result module test, on page 1011• diagnostic monitor interval module test all hour min second, on page 1012• diagnostic monitor module test all, on page 1013• diagnostic ondemand action-on-failure continue failure-count diagnostic ondemand action-on-failurestop, on page 1014
• diagnostic ondemand iteration, on page 1015• diagnostic ondemand test-parameter module test port_lb packet-length, on page 1016• diagnostic start module test, on page 1017• diagnostic stop module test all, on page 1018• diagnostic test simulation module test diagnostic test simulation module test clear, on page 1019• diff-clean, on page 1020
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)848
D Commands
Page 993
• diff-clean all-users, on page 1021• diff, on page 1022• dir, on page 1023• disable-connected-check, on page 1024• disable-fka, on page 1025• disable-peer-as-check, on page 1026• disable-policy-batching, on page 1027• disable, on page 1028• discard-route external, on page 1029• discard-route external, on page 1030• discovery, on page 1031• distance, on page 1032• distance, on page 1033• distance, on page 1034• distance, on page 1035• distance, on page 1036• distance, on page 1037• distance, on page 1038• distribute into route-map all, on page 1039• distribute link-state, on page 1040• dns, on page 1041• domain-id, on page 1042• domain-id secondary, on page 1043• domain-tag, on page 1044• dont-capability-negotiate, on page 1045• dos2nxos, on page 1046• dot1q, on page 1047• dot1q, on page 1048• dot1q, on page 1049• dot1q default dynamic, on page 1050• dot1x default, on page 1051• dot1x default, on page 1052• dot1x host-mode, on page 1053• dot1x initialize, on page 1054• dot1x mac-auth-bypass, on page 1055• dot1x mac-move, on page 1056• dot1x max-reauth-req, on page 1057• dot1x max-req, on page 1058• dot1x pae, on page 1059• dot1x port-control, on page 1060• dot1x radius-accounting, on page 1061• dot1x re-authenticate interface, on page 1062• dot1x re-authentication, on page 1063• dot1x re-authentication, on page 1064• dot1x show credential, on page 1065• dot1x start supplicant interface, on page 1066
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)849
D Commands
Page 994
• dot1x supplicant credential, on page 1067• dot1x supplicant credential, on page 1068• dot1x supplicant max-start, on page 1069• dot1x supplicant max-start, on page 1070• dot1x supplicant timeout auth-period, on page 1071• dot1x supplicant timeout auth-period, on page 1072• dot1x supplicant timeout held-period, on page 1073• dot1x supplicant timeout held-period, on page 1074• dot1x supplicant timeout start-period, on page 1075• dot1x supplicant timeout start-period, on page 1076• dot1x system-auth-control, on page 1077• dot1x timeout inactivity-period, on page 1078• dot1x timeout inactivity-period, on page 1079• dot1x timeout quiet-period, on page 1080• dot1x timeout quiet-period, on page 1081• dot1x timeout ratelimit-period, on page 1082• dot1x timeout re-authperiod, on page 1083• dot1x timeout re-authperiod, on page 1084• dot1x timeout server-timeout, on page 1085• dot1x timeout supp-timeout, on page 1086• dot1x timeout tx-period, on page 1087• dot1x timeout tx-period, on page 1088• down-bit-ignore, on page 1089• downlink delay, on page 1090• dpp set-qos-group, on page 1091• drop-trigger, on page 1092• droplist, on page 1093• droplist, on page 1094• dscp, on page 1095• dscp, on page 1096• dscp, on page 1097• dscp, on page 1098• dscp, on page 1099• dscp, on page 1100• dst-grp, on page 1101• dual-active exclude interface-vlan, on page 1102• duplex, on page 1103• duplex, on page 1104• duplicate-message throttle, on page 1105• dynamic-capability, on page 1106• dynamic-med-interval, on page 1107
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)850
D Commands
Page 995
dampen-igp-metricdampen-igp-metric <sec> | no dampen-igp-metric
Syntax Description
Negate a command or set its defaultsno
Dampen IGP metric-related changesdampen-igp-metric
Time interval in secondssec
Command Mode
• /exec/configure/router-bgp/router-bgp-af
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)851
D Commandsdampen-igp-metric
Page 996
dampening[no] dampening [ { <half-life> <reuse-limit> <suppress-limit> <max-suppress-time> } | { route-map<rmap-name> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure route flap dampeningdampening
(Optional) Decay half lifehalf-life
(Optional) Value to start reusing a routereuse-limit
(Optional) Value to start suppressing a routesuppress-limit
(Optional) Maximum suppress time for stable routemax-suppress-time
(Optional) Apply route-map to specify dampening criteriaroute-map
(Optional) Route-map namermap-name
Command Mode
• /exec/configure/router-bgp/router-bgp-af-ipv4-mdt /exec/configure/router-bgp/router-bgp-af-l2vpn-vpls
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)852
D Commandsdampening
Page 997
dampening[no] dampening | dampening [ { <half-life> [ { <reuse> <suppress> <max-suppress> } [ restart [ <penalty>] ] ] } ]
Syntax Description
Negate a command or set its defaultsno
configures dampenning featuredampening
(Optional) half-life time for the penaltyhalf-life
(Optional) Value to start reusing an interfacereuse
(Optional) Value to start suppressing an interfacesuppress
(Optional) Maximum duration to suppress an interfacemax-suppress
(Optional) Enable restart penaltyrestart
(Optional) Penalty applied at restartpenalty
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)853
D Commandsdampening
Page 998
dampening[no] dampening [ { <half-life> <reuse-limit> <suppress-limit> <max-suppress-time> } | { route-map<rmap-name> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure route flap dampeningdampening
(Optional) Decay half lifehalf-life
(Optional) Value to start reusing a routereuse-limit
(Optional) Value to start suppressing a routesuppress-limit
(Optional) Maximum suppress time for stable routemax-suppress-time
(Optional) Apply route-map to specify dampening criteriaroute-map
(Optional) Route-map namermap-name
Command Mode
• /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-vpnv4/exec/configure/router-bgp/router-bgp-af-vpnv6 /exec/configure/router-bgp/router-bgp-af-link-state/exec/configure/router-bgp/router-bgp-af-l2vpn-evpn /exec/configure/router-bgp/router-bgp-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-af-ipv6-mvpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)854
D Commandsdampening
Page 999
data-pattern{ { no | default } data-pattern | data-pattern <hex-pattern> }
Syntax Description
no
Set a command to its defaultsdefault
Data Patterndata-pattern
Data Pattern in Hexhex-pattern
Command Mode
• /exec/configure/ip-sla/udp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)855
D Commandsdata-pattern
Page 1000
data-pattern pad{ data-pattern pad <pad-val> }
Syntax Description
Configure NGOAM ping payloaddata-pattern
Configure NGOAM payload test pattern padpad
Configure NGOAM payload test pad valuepad-val
Command Mode
• /exec/configure/configngoamconnectcheck
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)856
D Commandsdata-pattern pad
Page 1001
data-source{ data-source <type> } | { no data-source [ <type> ] }
Syntax Description
Negate a command or set its defaultsno
Specify the data sourcedata-source
type
Command Mode
• /exec/configure/telemetry/sensor-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)857
D Commandsdata-source
Page 1002
database-mapping{ [ no ] database-mapping { <eid-prefix> | <eid-prefix6> } { redistribute | { { <locator> | <locator6> } priority<priority> weight <weight> } } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure EID-prefix and locator-set for dynamic-EIDdatabase-mapping
IP EID-prefix for RLOC static mappingeid-prefix
IP address of LISP-VM routerslocator
Configures which Locators from a set are preferredpriority
Lower priority Locator takes preferencepriority
Traffic load-spreading among Locatorsweight
Specified in a percentage from 0 to 100weight
Used for redistirbuting into routing protocolsredistribute
Command Mode
• /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)858
D Commandsdatabase-mapping
Page 1003
databits[no] databits <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set number of databits per characterdatabits
Number of data bitsi0
Command Mode
• /exec/configure/com1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)859
D Commandsdatabits
Page 1004
databits[no] databits <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set number of databits per characterdatabits
Number of data bitsi0
Command Mode
• /exec/configure/console
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)860
D Commandsdatabits
Page 1005
datapath-iddatapath-id <datapathid-val> | no datapath-id
Syntax Description
Negate a command or set its defaultsno
Datapath IDdatapath-id
64-bit hex value [0x1-0xffffffffffffffff]datapathid-val
Command Mode
• /exec/configure/openflow/switch/sub-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)861
D Commandsdatapath-id
Page 1006
datapath-iddatapath-id <datapathid-val> | no datapath-id
Syntax Description
Negate a command or set its defaultsno
Datapath IDdatapath-id
64-bit hex value [0x1-0xffffffffffffffff]datapathid-val
Command Mode
• /exec/configure/openflow/switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)862
D Commandsdatapath-id
Page 1007
db-jid[no] db-jid <jid> [ key-type <key-type> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Jabber ID of databasedb-jid
Enter Jabber ID of databasejid
(Optional) Query key type for this databasekey-type
(Optional)key-type
Command Mode
• /exec/configure/fabric-db/server-xmpp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)863
D Commandsdb-jid
Page 1008
db-security user password[no] db-security user <user> password { 0 <clear> | 7 <encrypted> | <password> } [ shared-secret { 10 <clear>| 7 <encrypted> | <secret> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Database Securitydb-security
User IDuser
Enter user IDuser
Passwordpassword
Password that follows should be in clear text0
Password in clear textclear
Password that follows should be in encrypted text7
Encrypted passwordencrypted
Enter password in clear textpassword
(Optional) Shared-secretshared-secret
(Optional) Indicates that password that follows should be in clear text10
(Optional) Password in clear textclear
(Optional) Password that follows should be in encrypted text7
(Optional) Encrypted passwordencrypted
(Optional) Enter shared-secret in clear textsecret
Command Mode
• /exec/configure/fabric-db/server-ldap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)864
D Commandsdb-security user password
Page 1009
db-table[no] db-table <tablename> [ key-type <key-type> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Table name to searchdb-table
Enter table name to searchtablename
(Optional) Query key type for this tablekey-type
(Optional)key-type
Command Mode
• /exec/configure/fabric-db/server-ldap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)865
D Commandsdb-table
Page 1010
dead-interval{ { dead-interval <interval> } | { no dead-interval [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Dead intervaldead-interval
(seconds)interval
Command Mode
• /exec/configure/router-ospf/vrf/router-ospf-slink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)866
D Commandsdead-interval
Page 1011
dead-interval{ { dead-interval <interval> } | { no dead-interval [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Dead intervaldead-interval
(seconds)interval
Command Mode
• /exec/configure/router-ospf3/router-ospf3-vlink /exec/configure/router-ospf3/vrf/router-ospf3-vlink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)867
D Commandsdead-interval
Page 1012
dead-interval{ { dead-interval <interval> } | { no dead-interval [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Dead intervaldead-interval
(seconds)interval
Command Mode
• /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)868
D Commandsdead-interval
Page 1013
deadtime[no] deadtime <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
duration for which non-reachable server is skippeddeadtime
Length of time, in minutesi0
Command Mode
• /exec/configure/ldap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)869
D Commandsdeadtime
Page 1014
deadtime[no] deadtime <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
duration for which non-reachable server is skippeddeadtime
Length of time, in minutesi0
Command Mode
• /exec/configure/radius
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)870
D Commandsdeadtime
Page 1015
deadtime[no] deadtime <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
duration for which non-reachable server is skippeddeadtime
Length of time, in minutesi0
Command Mode
• /exec/configure/tacacs+
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)871
D Commandsdeadtime
Page 1016
default-information originate[no] default-information originate [ always ] [ route-map <map-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
RIP control distribution of default routedefault-information
RIP distribute a default routeoriginate
(Optional) RIP always advertise default routealways
(Optional) Policy to constrain redistributionroute-map
(Optional) Route-map namemap-name
Command Mode
• /exec/configure/router-rip/router-rip-af-common /exec/configure/router-rip/router-rip-vrf-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)872
D Commandsdefault-information originate
Page 1017
default-information originate[no] default-information originate [ always ] [ route-map <map-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Control origination of a default routedefault-information
Originate a default routeoriginate
(Optional) Always advertise default routealways
(Optional) Route-map to announce default routesroute-map
(Optional) A 'routing-rules' route-map namemap-name
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common /exec/configure/router-isis/router-isis-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)873
D Commandsdefault-information originate
Page 1018
default-information originate[no] default-information originate [ always ] [ route-map <policy-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Control distribution of default routedefault-information
Distribute a default routeoriginate
(Optional) Always advertise default routealways
(Optional) Policy to control distribution of default routeroute-map
(Optional) Route-map namepolicy-name
Command Mode
• /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)874
D Commandsdefault-information originate
Page 1019
default-information originate[no] default-information originate [ always ] [ route-map <map> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Control origination of a default routedefault-information
Originate a default routeoriginate
(Optional) Always advertise default routealways
(Optional) Use a route-map for default route metricsroute-map
(Optional) Route-map namemap
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)875
D Commandsdefault-information originate
Page 1020
default-information originate[no] default-information originate [ always ] [ route-map <policy-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Control distribution of default routedefault-information
Distribute a default routeoriginate
(Optional) Always advertise default routealways
(Optional) Policy to control distribution of default routeroute-map
(Optional) Route-map namepolicy-name
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)876
D Commandsdefault-information originate
Page 1021
default-information originate[no] default-information originate
Syntax Description
(Optional) Negate a command or set its defaultsno
Control distribution of default informationdefault-information
Distribute a default routeoriginate
Command Mode
• /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-ipv6-label/exec/configure/router-bgp/router-bgp-af-ipv4-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)877
D Commandsdefault-information originate
Page 1022
default-information originate always rd route-target[no] default-information originate always rd { <ext-comm-rd-aa2nn4> | <ext-comm-rd-aa4nn2> } route-target{ <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Control distribution of default informationdefault-information
Distribute a default routeoriginate
Always advertise default routealways
VPN Route Distinguisherrd
VPN route distinguisher in aa4:nn or ip:nn formatext-comm-rd-aa4nn2
VPN route distinguisher in aa:nn formatext-comm-rd-aa2nn4
Specify Target VPN Extended Communitiesroute-target
RT extcommunity in aa4:nn or ip:nn formatext-comm-rt-aa4nn2
RT extcommunity in aa:nn formatext-comm-rt-aa2nn4
Command Mode
• /exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-vpnv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)878
D Commandsdefault-information originate always rd route-target
Page 1023
default-metric[no] default-metric <metric>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set metric of redistributed routesdefault-metric
Default Metricmetric
Command Mode
• /exec/configure/router-bgp/router-bgp-af
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)879
D Commandsdefault-metric
Page 1024
default-metricdefault-metric <metric> | no default-metric [ <metric> ]
Syntax Description
Negate a command or set its defaultsno
RIP default metricdefault-metric
RIP metric valuemetric
Command Mode
• /exec/configure/router-rip/router-rip-af-common /exec/configure/router-rip/router-rip-vrf-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)880
D Commandsdefault-metric
Page 1025
default-metric{ default-metric <cost> } | { no default-metric [ <cost> ] }
Syntax Description
Negate a command or set its defaultsno
Specify default metric for redistributed routesdefault-metric
Metric valuecost
Command Mode
• /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)881
D Commandsdefault-metric
Page 1026
default-metric{ { default-metric <bw> <delay> <rel> <load> <mtu> } | { no default-metric [ <bw> <delay> <rel> <load><mtu> ] } }
Syntax Description
Negate a command or set its defaultsno
Set metric of redistributed routesdefault-metric
Bandwidth in Kbits per secondbw
Delay metricdelay
Reliability metric where 255 is 100% reliablerel
Effective bandwidth metric (Loading) where 255 is 100% loadedload
Maximum Transmission Unit metric of the pathmtu
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)882
D Commandsdefault-metric
Page 1027
default-metric{ default-metric <cost> } | { no default-metric [ <cost> ] }
Syntax Description
Negate a command or set its defaultsno
Specify default metric for redistributed routesdefault-metric
Metric valuecost
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)883
D Commandsdefault-metric
Page 1028
default-missdefault-miss { continue-drop | continue-normal | continue-controller | drop | normal | controller } | nodefault-miss
Syntax Description
Negate a command or set its defaultsno
Setcontinue-drop/continue-normal/continue-controller/drop/normal/controllerflow action
default-miss
cascade drop to next tablecontinue-drop
cascade normal to next tablecontinue-normal
cascade punt to next tablecontinue-controller
drop packetdrop
forward to normal dataplanenormal
punt to controllercontroller
Command Mode
• /exec/configure/openflow/switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)884
D Commandsdefault-miss
Page 1029
default-originate[ no | default ] default-originate [ route-map <rmap-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Originate a default toward this peerdefault-originate
(Optional) Route-map to specify criteria for originating defaultroute-map
(Optional) Route-map namermap-name
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)885
D Commandsdefault-originate
Page 1030
default echo revisiondefault echo { revision | vendor-extension }
Syntax Description
Set a command to its defaultsdefault
Echo Request attributesecho
Echo packet default revisionrevision
Send Vendor Extension TLV with echo Reqvendor-extension
Command Mode
• /exec/configure/mpls-oam
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)886
D Commandsdefault echo revision
Page 1031
default permit[no] default { permit | deny }
Syntax Description
(Optional) Negate a command or set its defaultsno
Default Host Admission Policydefault
Admission Permittedpermit
Admission Denieddeny
Command Mode
• /exec/configure/nbm-host-policy/sender
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)887
D Commandsdefault permit
Page 1032
default permit[no] default { permit | deny }
Syntax Description
(Optional) Negate a command or set its defaultsno
Default Host Admission Policydefault
Admission Permittedpermit
Admission Denieddeny
Command Mode
• /exec/configure/nbm-host-policy/receiver
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)888
D Commandsdefault permit
Page 1033
default permit[no] default { permit | deny }
Syntax Description
(Optional) Negate a command or set its defaultsno
Default Host Admission Policydefault
Admission Permittedpermit
Admission Denieddeny
Command Mode
• /exec/configure/nbm-host-policy/pim
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)889
D Commandsdefault permit
Page 1034
define[no] define <paramname> [ <paramtype> ] [ <paramdesc> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Define a parameterdefine
Enter the name of the parameterparamname
(Optional) param typeparamtype
(Optional) Enter the parameter descriptionparamdesc
Command Mode
• /exec/configure/param-list
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)890
D Commandsdefine
Page 1035
delay-restore time[no] delay-restore time <sec>
Syntax Description
(Optional) Negate a command or set its defaultsno
delay-restoredelay-restore
timetime
time in secondssec
Command Mode
• /exec/configure/config-evpn-msite-bgw
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)891
D Commandsdelay-restore time
Page 1036
delaydelay <microseconds> | no delay
Syntax Description
Negate a command or set its defaultsno
Specify interface throughput delaydelay
Throughput delay (tens of microseconds)microseconds
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)892
D Commandsdelay
Page 1037
delaydelay <delay_val> | no delay [ <delay_val> ]
Syntax Description
Negate a command or set its defaultsno
Specify interface throughput delaydelay
Throughput delay (tens of microseconds)delay_val
Command Mode
• /exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p /exec/configure/if-port-channel-sub
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)893
D Commandsdelay
Page 1038
delaydelay <delay_val> | no delay [ <delay_val> ]
Syntax Description
Negate a command or set its defaultsno
Specify interface throughput delaydelay
Throughput delay (tens of microseconds)delay_val
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel/exec/configure/if-ethernet-all /exec/configure/if-ethernet-p2p /exec/configure/if-remote-ethernet-sub/exec/configure/if-port-channel-range
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)894
D Commandsdelay
Page 1039
delay peer-linkdelay peer-link <time> | no delay peer-link
Syntax Description
Negate a command or set its defaultsno
Peer-link bringup delaydelay
Delay peer-link bringuppeer-link
Delay in bringing up the peer-link (in seconds)time
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)895
D Commandsdelay peer-link
Page 1040
delay restoredelay restore <time-out> | no delay restore
Syntax Description
Negate a command or set its defaultsno
Initialization delaydelay
Delay after restoring peer-linkrestore
Delay in bringing up the vPC links (in seconds)time-out
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)896
D Commandsdelay restore
Page 1041
delay restore interface-vlandelay restore interface-vlan <time-out> | no delay restore interface-vlan
Syntax Description
Negate a command or set its defaultsno
Initialization delaydelay
Delay after restoring peer-linkrestore
Delay in bringing-up interface-vlaninterface-vlan
Delay in bringing up the interface-vlan (in seconds)time-out
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)897
D Commandsdelay restore interface-vlan
Page 1042
delay restore orphan-portdelay restore orphan-port <delay_time> | no delay restore orphan-port
Syntax Description
Negate a command or set its defaultsno
Initialization delaydelay
Delay after restoring peer-linkrestore
Configure vPC orphan-port delay bring-up timerorphan-port
Specify delay time in secondsdelay_time
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)898
D Commandsdelay restore orphan-port
Page 1043
delay updelay { { up <up_delay> [ down <down_delay> ] } | { down <down_delay> [ up <up_delay> ] } } | no delay
Syntax Description
Negate a command or set its defaultsno
Tracking delaydelay
Delay up change notificationup
Seconds to delayup_delay
(Optional) Delay down change notificationdown
(Optional) Seconds to delaydown_delay
Command Mode
• /exec/configure/track /exec/configure/tr-list-bool /exec/configure/tr-list-thrp /exec/configure/tr-list-thrw
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)899
D Commandsdelay up
Page 1044
deletedelete { <uri0> | <uri1> | <uri2> } [ no-prompt ]
Syntax Description
delete a file or directorydelete
Delete a file or directoryuri0
Delete a file or directory on expansion flashuri1
Directory or filename on logflashuri2
(Optional) Do not prompt for multiple deletion of filesno-prompt
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)900
D Commandsdelete
Page 1045
delete ca-certificatedelete ca-certificate
Syntax Description
Delete the certificatesdelete
Delete the ca certificatesca-certificate
Command Mode
• /exec/configure/trustpoint
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)901
D Commandsdelete ca-certificate
Page 1046
delete certificatedelete certificate [ force ]
Syntax Description
Delete the certificatesdelete
Delete the identity certificatecertificate
(Optional) Force delete the identity certificateforce
Command Mode
• /exec/configure/trustpoint
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)902
D Commandsdelete certificate
Page 1047
delete crldelete crl
Syntax Description
Delete the certificatesdelete
Delete the CRLcrl
Command Mode
• /exec/configure/trustpoint
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)903
D Commandsdelete crl
Page 1048
demand-circuit[no] demand-circuit
Syntax Description
(Optional) Negate a command or set its defaultsno
OSPF Demand circuitdemand-circuit
Command Mode
• /exec/configure/router-ospf/vrf/router-ospf-slink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)904
D Commandsdemand-circuit
Page 1049
depth{ [ no ] depth <cells> | no depth }
Syntax Description
Provide the number of cells for this INT queue_profiledepth
queue_profile depth (number of cells). Default is 300cells
Command Mode
• /exec/configure/config-int-q-prof
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)905
D Commandsdepth
Page 1050
depth{ [ no ] depth <cells> | no depth }
Syntax Description
Provide the number of cells for this POSTCARD queue_profiledepth
queue_profile depth (number of cells/packets). Default is 300cells
Command Mode
• /exec/configure/config-postcard-q-prof
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)906
D Commandsdepth
Page 1051
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this Flow Exporterdescription
Monitor description string (63 characters maximum)line
Command Mode
• /exec/configure/config-int-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)907
D Commandsdescription
Page 1052
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this INT Recorddescription
Record description string (63 characters maximum)line
Command Mode
• /exec/configure/config-int-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)908
D Commandsdescription
Page 1053
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this INT Watchlistdescription
Watchlist description string (63 characters maximum)line
Command Mode
• /exec/configure/config-int-watchlist
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)909
D Commandsdescription
Page 1054
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this INT Monitordescription
Monitor description string (63 characters maximum)line
Command Mode
• /exec/configure/config-int-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)910
D Commandsdescription
Page 1055
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this INT queue_profiledescription
queue_profile description string (63 characters maximum)line
Command Mode
• /exec/configure/config-int-q-prof
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)911
D Commandsdescription
Page 1056
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this INT flow-profiledescription
flow-profile description string (63 characters maximum)line
Command Mode
• /exec/configure/config-int-flow-prof
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)912
D Commandsdescription
Page 1057
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this Flow Recorddescription
Record description string (63 characters maximum)line
Command Mode
• /exec/configure/config-fte-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)913
D Commandsdescription
Page 1058
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this FTE Monitordescription
Monitor description string (63 characters maximum)line
Command Mode
• /exec/configure/config-fte-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)914
D Commandsdescription
Page 1059
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this FTE Evenydescription
Event description string (63 characters maximum)line
Command Mode
• /exec/configure/config-fte-event
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)915
D Commandsdescription
Page 1060
descriptiondescription <desc_line> | no description [ <desc_line> ]
Syntax Description
Negate a command or set its defaultsno
Enter description of maximum 80 charactersdescription
Description of maximum 80 charactersdesc_line
Command Mode
• /exec/configure/if-vfc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)916
D Commandsdescription
Page 1061
descriptiondescription <descr> | no description
Syntax Description
Negate a command or set its defaultsno
Session description (max 32 characters)description
Enter the description string(can include spaces)descr
Command Mode
• /exec/configure/monitor-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)917
D Commandsdescription
Page 1062
descriptiondescription <desc_line> | no description [ <desc_line> ]
Syntax Description
Negate a command or set its defaultsno
Enter description of maximum 254 charactersdescription
Description of maximum 254 charactersdesc_line
Command Mode
• /exec/configure/if-any-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)918
D Commandsdescription
Page 1063
description{ description <desc-str> | no description [ <desc-str> ] }
Syntax Description
Negate a command or set its defaultsno
Class-Map descriptiondescription
Description of this class-map (up to 200 characters)desc-str
Command Mode
• /exec/configure/class-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)919
D Commandsdescription
Page 1064
description[no] description <desc-str>
Syntax Description
(Optional) Negate a command or set its defaultsno
Class-Map descriptiondescription
Description of this class-map (up to 200 characters)desc-str
Command Mode
• /exec/configure/class-map/type/queuing
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)920
D Commandsdescription
Page 1065
description{ description <desc-str> | no description [ <desc-str> ] }
Syntax Description
Negate a command or set its defaultsno
Table-Map descriptiondescription
Description of this table-map (up to 200 characters)desc-str
Command Mode
• /exec/configure/table-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)921
D Commandsdescription
Page 1066
description{ description <desc-str> | no description [ <desc-str> ] }
Syntax Description
Negate a command or set its defaultsno
Policy-Map descriptiondescription
Description of this policy-map (up to 200 characters)desc-str
Command Mode
• /exec/configure/policy-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)922
D Commandsdescription
Page 1067
description{ description <desc-str> | no description [ <desc-str> ] }
Syntax Description
Negate a command or set its defaultsno
Policy-Map descriptiondescription
Description of this policy-map (up to 200 characters)desc-str
Command Mode
• /exec/configure/policy-map/type/queuing
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)923
D Commandsdescription
Page 1068
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this Flow Recorddescription
Record description string (63 characters maximum)line
Command Mode
• /exec/configure/nfm-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)924
D Commandsdescription
Page 1069
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this Flow Monitordescription
Monitor description string (63 characters maximum)line
Command Mode
• /exec/configure/nfm-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)925
D Commandsdescription
Page 1070
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this Flow Exporterdescription
Monitor description string (63 characters maximum)line
Command Mode
• /exec/configure/nfm-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)926
D Commandsdescription
Page 1071
descriptiondescription [ port-profile ] <desc_line> | no description [ port-profile ] [ <desc_line> ]
Syntax Description
Negate a command or set its defaultsno
Enter port-profile description of maximum 80 charactersdescription
(Optional) Hack for conf-syncport-profile
Enter port-profile description of maximum 80 charactersdesc_line
Command Mode
• /exec/configure/port-profile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)927
D Commandsdescription
Page 1072
description{ description <desc-str> | no description [ <desc-str> ] }
Syntax Description
Negate a command or set its defaultsno
Class-Map descriptiondescription
Description of this class-map (up to 200 characters)desc-str
Command Mode
• /exec/configure/class-map/type/uf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)928
D Commandsdescription
Page 1073
description{ description <desc-str> | no description [ <desc-str> ] }
Syntax Description
Negate a command or set its defaultsno
Policy-Map descriptiondescription
Description of this policy-map (up to 200 characters)desc-str
Command Mode
• /exec/configure/policy-map/type/uf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)929
D Commandsdescription
Page 1074
descriptiondescription <desc> | no description
Syntax Description
Negate a command or set its defaultsno
Fabric Path topology descriptiondescription
Description of maximum 80 charactersdesc
Command Mode
• /exec/configure/fp-topology
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)930
D Commandsdescription
Page 1075
description{ description <description_text> | no description [ <description_text> ] }
Syntax Description
Negate a command or set its defaultsno
Virtual service descriptiondescription
Description of this virtual servicedescription_text
Command Mode
• /exec/configure/virt-serv
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)931
D Commandsdescription
Page 1076
description[no] description <description>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure description for the policydescription
Description for the policydescription
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)932
D Commandsdescription
Page 1077
description[no] description
Syntax Description
Negate a command or set its defaultsno
Configure description for the policydescription
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)933
D Commandsdescription
Page 1078
descriptiondescription <desc_line> | no description
Syntax Description
Negate a command or set its defaultsno
Interface specific descriptiondescription
Up to 255 characters describing this interfacedesc_line
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)934
D Commandsdescription
Page 1079
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this Flow Exporterdescription
Monitor description string (63 characters maximum)line
Command Mode
• /exec/configure/config-postcard-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)935
D Commandsdescription
Page 1080
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this POSTCARD Watchlistdescription
Watchlist description string (63 characters maximum)line
Command Mode
• /exec/configure/config-postcard-watchlist
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)936
D Commandsdescription
Page 1081
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this POSTCARD Monitordescription
Monitor description string (63 characters maximum)line
Command Mode
• /exec/configure/config-postcard-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)937
D Commandsdescription
Page 1082
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this POSTCARD queue_profiledescription
queue_profile description string (63 characters maximum)line
Command Mode
• /exec/configure/config-postcard-q-prof
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)938
D Commandsdescription
Page 1083
description{ [ no ] description <line> | no description }
Syntax Description
Provide a description for this POSTCARD flow-profiledescription
flow-profile description string (63 characters maximum)line
Command Mode
• /exec/configure/config-postcard-flow-prof
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)939
D Commandsdescription
Page 1084
descriptiondescription <line> | no description
Syntax Description
Negate a command or set its defaultsno
Add a description for the roledescription
Enter the description string(can include spaces)line
Command Mode
• /exec/configure/role
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)940
D Commandsdescription
Page 1085
description{ description <line> | no description }
Syntax Description
Negate a command or set its defaultsno
Description of the route-mapdescription
Route-map description stringline
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)941
D Commandsdescription
Page 1086
descriptiondescription <desc_line> | no description [ <desc_line> ]
Syntax Description
Negate a command or set its defaultsno
Enter description of maximum 254 charactersdescription
Description of maximum 254 charactersdesc_line
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-port-channel /exec/configure/if-eth-port-channel/exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p /exec/configure/if-port-channel-sub/exec/configure/if-loopback /exec/configure/if-ethernet-all /exec/configure/if-ethernet-p2p/exec/configure/if-remote-ethernet-sub /exec/configure/if-port-channel-range
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)942
D Commandsdescription
Page 1087
descriptiondescription <desc_line> | no description [ <desc_line> ]
Syntax Description
Negate a command or set its defaultsno
Enter description of maximum 254 charactersdescription
Description of maximum 254 charactersdesc_line
Command Mode
• /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)943
D Commandsdescription
Page 1088
descriptiondescription <desc_line> | no description [ <desc_line> ]
Syntax Description
Negate a command or set its defaultsno
Enter description of maximum 254 charactersdescription
Description of maximum 254 charactersdesc_line
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)944
D Commandsdescription
Page 1089
descriptiondescription <desc_line> | no description [ <desc_line> ]
Syntax Description
Negate a command or set its defaultsno
Enter description of maximum 80 charactersdescription
Description of maximum 80 charactersdesc_line
Command Mode
• /exec/configure/if-overlay /exec/configure/if-te /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)945
D Commandsdescription
Page 1090
description[no] description [ <desc> ] | description <desc>
Syntax Description
Negate a command or set its defaultsno
Group descriptiondescription
(Optional) Up to 80 characters describing this groupdesc
Command Mode
• /exec/configure/if-eth-any/vrrpv3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)946
D Commandsdescription
Page 1091
description{ description <line> } | { no description }
Syntax Description
Negate a command or set its defaultsno
Description of the VRFdescription
VRF description stringline
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)947
D Commandsdescription
Page 1092
description{ [ no ] description <descrip-string> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Provide a description string for the LISP sitedescription
Description stringdescrip-string
Command Mode
• /exec/configure/lisp-site /exec/configure/vrf/lisp-site
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)948
D Commandsdescription
Page 1093
descriptiondescription <describe> | no description
Syntax Description
Negate a command or set its defaultsno
Description for the BMP serverdescription
Upto 80 characters describing this serverdescribe
Command Mode
• /exec/configure/router-bgp/router-bgp-bmp-server
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)949
D Commandsdescription
Page 1094
descriptiondescription <describe> | { no | default } description [ <describe> ]
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Neighbor specific descriptiondescription
Upto 80 characters describing this neighbordescribe
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)950
D Commandsdescription
Page 1095
description{ [ no ] description <text> }
Syntax Description
description for this profiledescription
descriptiontext
Command Mode
• /exec/configure/dot1x-cred
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)951
D Commandsdescription
Page 1096
description{ description <descr> } | { no description }
Syntax Description
Configure description of the profiledescription
Description of maximum 64 charactersdescr
Command Mode
• /exec/configure/configngoamprofile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)952
D Commandsdescription
Page 1097
description description[no] description | description <desc>
Syntax Description
(Optional) Negate a command or set its defaultsno
Pathway descriptiondescription
Up to 80 characters describing this pathwaydesc
Command Mode
• /exec/configure/if-eth-any/vrrs
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)953
D Commandsdescription description
Page 1098
dest-ipaddr{ dest-ipaddr { <ip-address> | <hostname> | <ipv6-address> } }
Syntax Description
Destination ip addressdest-ipaddr
IP address, broadcast disallowedip-address
IP Hostname, broadcast disallowedhostname
Command Mode
• /exec/configure/ip-sla/tcp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)954
D Commandsdest-ipaddr
Page 1099
dest-ipaddr{ dest-ipaddr { <ip-address> | <hostname> } }
Syntax Description
Destination ip addressdest-ipaddr
IP address, broadcast disallowedip-address
IP Hostname, broadcast disallowedhostname
Command Mode
• /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)955
D Commandsdest-ipaddr
Page 1100
dest-port{ dest-port <port> }
Syntax Description
Destination portdest-port
udp port numberport
Command Mode
• /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/tcp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)956
D Commandsdest-port
Page 1101
dest{ dest { { ip { <numeric10> | <numeric11> | unknown } } | { mac <dmac> <dot1qid> [ <intfid> ] } } }
Syntax Description
destination nodedest
ip addressip
Ipv4 address of remote host / VTEPnumeric10
Peer vtep ip is unknown, Applicable only for channel Nv03unknown
Macmac
Destination mac addressdmac
Encapsulation dot1q/bd on which the mac is learntdot1qid
(Optional) Name of the interface for ngoam ping on which dot1q isconfigured
intfid
Command Mode
• /exec/configure/configngoamconnectcheck
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)957
D Commandsdest
Page 1102
destination-group[no] destination-group <dgrp-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Create destination groupdestination-group
Identifierdgrp-id
Command Mode
• /exec/configure/telemetry
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)958
D Commandsdestination-group
Page 1103
destination-profile[no] destination-profile <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
User defined destination profile names0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)959
D Commandsdestination-profile
Page 1104
destination-profile[no] destination-profile
Syntax Description
(Optional) Negate a command or set its defaultsno
Specify the default destination profiledestination-profile
Command Mode
• /exec/configure/telemetry
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)960
D Commandsdestination-profile
Page 1105
destination-profile CiscoTAC-1 alert-group[no] destination-profile CiscoTAC-1 alert-group { All | Configuration | Diagnostic | EEM | Cisco-TAC |Environmental | Inventory | License | Linecard-Hardware | Supervisor-Hardware | Syslog-group-port | System| Test }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for XML messageCiscoTAC-1
Add alert groupalert-group
This alert group consists of all of the callhome messagesAll
Events which are meant for Cisco TAC onlyCisco-TAC
Power,fan,temperature related eventsEnvironmental
Inventory status eventsInventory
Events related to licensingLicense
Linecard related eventsLinecard-Hardware
Supervisor related eventsSupervisor-Hardware
Events related to syslog messages filed by port managerSyslog-group-port
Software related eventsSystem
User generated test eventsTest
Events related to ConfigurationConfiguration
Events related to DiagnosticDiagnostic
EEM eventsEEM
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)961
D Commandsdestination-profile CiscoTAC-1 alert-group
Page 1106
destination-profile CiscoTAC-1 email-addr[no] destination-profile CiscoTAC-1 email-addr <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for XML messageCiscoTAC-1
Add email addremail-addr
Provide email address, example: [email protected]
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)962
D Commandsdestination-profile CiscoTAC-1 email-addr
Page 1107
destination-profile CiscoTAC-1 http[no] destination-profile CiscoTAC-1 http <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for XML messageCiscoTAC-1
Add http or https urlhttp
Provide http or https url, example1: http://site.com/services/callservexample2: https://site2.com/serv/CALL
s0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)963
D Commandsdestination-profile CiscoTAC-1 http
Page 1108
destination-profile CiscoTAC-1 message-level[no] destination-profile CiscoTAC-1 message-level <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for XML messageCiscoTAC-1
Callhome message level(0-lowest urgency, 9-highest urgency)message-level
i0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)964
D Commandsdestination-profile CiscoTAC-1 message-level
Page 1109
destination-profile CiscoTAC-1 message-size[no] destination-profile CiscoTAC-1 message-size <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for XML messageCiscoTAC-1
Configure maximum message size (default 5000000)message-size
Provide maximum possible message sizei0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)965
D Commandsdestination-profile CiscoTAC-1 message-size
Page 1110
destination-profile CiscoTAC-1 transport-method http[no] destination-profile CiscoTAC-1 transport-method http
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for XML messageCiscoTAC-1
Callhome message sending transport-methodtransport-method
http transport-methodhttp
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)966
D Commandsdestination-profile CiscoTAC-1 transport-method http
Page 1111
destination-profile CiscoTAC-1 transport-method email[no] destination-profile CiscoTAC-1 transport-method email
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for XML messageCiscoTAC-1
Callhome message sending transport-methodtransport-method
email transport-methodemail
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)967
D Commandsdestination-profile CiscoTAC-1 transport-method email
Page 1112
destination-profile alert-group[no] destination-profile <s0> alert-group { All | Configuration | Diagnostic | EEM | Cisco-TAC | Environmental| Inventory | License | Linecard-Hardware | Supervisor-Hardware | Syslog-group-port | System | Test }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
User defined destination profile names0
Add alert groupalert-group
This alert group consists of all of the callhome messagesAll
Events which are meant for Cisco TAC onlyCisco-TAC
Power,fan,temperature related eventsEnvironmental
Inventory status eventsInventory
Events related to licensingLicense
Linecard related eventsLinecard-Hardware
Supervisor related eventsSupervisor-Hardware
Events related to syslog messages filed by port managerSyslog-group-port
Software related eventsSystem
User generated test eventsTest
Events related to ConfigurationConfiguration
Events related to DiagnosticDiagnostic
EEM eventsEEM
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)968
D Commandsdestination-profile alert-group
Page 1113
destination-profile email-addr[no] destination-profile <s0> email-addr <s1>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
User defined destination profile names0
Add email addremail-addr
Provide email address, example: [email protected]
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)969
D Commandsdestination-profile email-addr
Page 1114
destination-profile formatdestination-profile <s0> format { full-txt | short-txt | XML }
Syntax Description
Configure destination profilesdestination-profile
User defined destination profile names0
Callhome message format (default XML)format
Plain text message formatfull-txt
Short text message formatshort-txt
XML message formatXML
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)970
D Commandsdestination-profile format
Page 1115
destination-profile full-txt-destination alert-group[no] destination-profile full-txt-destination alert-group { All | Configuration | Diagnostic | EEM | Cisco-TAC| Environmental | Inventory | License | Linecard-Hardware | Supervisor-Hardware | Syslog-group-port | System| Test }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for plain txt messagefull-txt-destination
Add alert groupalert-group
This alert group consists of all of the callhome messagesAll
Events which are meant for Cisco TAC onlyCisco-TAC
Power,fan,temperature related eventsEnvironmental
Inventory status eventsInventory
Events related to licensingLicense
Linecard related eventsLinecard-Hardware
Supervisor related eventsSupervisor-Hardware
Events related to syslog messages filed by port managerSyslog-group-port
Software related eventsSystem
User generated test eventsTest
Events related to ConfigurationConfiguration
Events related to DiagnosticDiagnostic
EEM eventsEEM
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)971
D Commandsdestination-profile full-txt-destination alert-group
Page 1116
destination-profile full-txt-destination email-addr[no] destination-profile full-txt-destination email-addr <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for plain txt messagefull-txt-destination
Add email addremail-addr
Provide email address, example: [email protected]
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)972
D Commandsdestination-profile full-txt-destination email-addr
Page 1117
destination-profile full-txt-destination http[no] destination-profile full-txt-destination http <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for plain txt messagefull-txt-destination
Add http or https urlhttp
Provide http or https url, example1: http://site.com/services/callservexample2: https://site2.com/serv/CALL
s0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)973
D Commandsdestination-profile full-txt-destination http
Page 1118
destination-profile full-txt-destination message-size[no] destination-profile full-txt-destination message-size <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for plain txt messagefull-txt-destination
Configure maximum message size (default 2500000)message-size
Provide maximum possible message sizei0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)974
D Commandsdestination-profile full-txt-destination message-size
Page 1119
destination-profile full-txt-destination message-level[no] destination-profile full-txt-destination message-level <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for plain txt messagefull-txt-destination
Callhome message level(0-lowest urgency, 9-highest urgency)message-level
i0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)975
D Commandsdestination-profile full-txt-destination message-level
Page 1120
destination-profile full-txt-destination transport-method http[no] destination-profile full-txt-destination transport-method http
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for plain txt messagefull-txt-destination
Callhome message sending transport-methodtransport-method
http transport-methodhttp
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)976
D Commandsdestination-profile full-txt-destination transport-method http
Page 1121
destination-profile full-txt-destination transport-method email[no] destination-profile full-txt-destination transport-method email
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for plain txt messagefull-txt-destination
Callhome message sending transport-methodtransport-method
email transport-methodemail
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)977
D Commandsdestination-profile full-txt-destination transport-method email
Page 1122
destination-profile http[no] destination-profile <s4> { http <s2> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
User defined destination profile names4
Add http or https urlhttp
Provide http or https url, example1: http://site.com/services/callservexample2: https://site2.com/serv/CALL
s2
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)978
D Commandsdestination-profile http
Page 1123
destination-profile message-level[no] destination-profile <s0> message-level <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
User defined destination profile names0
Callhome message level(0-lowest urgency, 9-highest urgency)message-level
i0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)979
D Commandsdestination-profile message-level
Page 1124
destination-profile message-size[no] destination-profile <s0> message-size <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
User defined destination profile names0
Configure maximum message size (default 2500000)message-size
Provide maximum possible message sizei0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)980
D Commandsdestination-profile message-size
Page 1125
destination-profile short-txt-destination alert-group[no] destination-profile short-txt-destination alert-group { All | Configuration | Diagnostic | EEM | Cisco-TAC| Environmental | Inventory | License | Linecard-Hardware | Supervisor-Hardware | Syslog-group-port | System| Test }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for short txt messageshort-txt-destination
Add alert groupalert-group
This alert group consists of all of the callhome messagesAll
Events which are meant for Cisco TAC onlyCisco-TAC
Power,fan,temperature related eventsEnvironmental
Inventory status eventsInventory
Events related to licensingLicense
Linecard related eventsLinecard-Hardware
Supervisor related eventsSupervisor-Hardware
Events related to syslog messages filed by port managerSyslog-group-port
Software related eventsSystem
User generated test eventsTest
Events related to ConfigurationConfiguration
Events related to DiagnosticDiagnostic
EEM eventsEEM
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)981
D Commandsdestination-profile short-txt-destination alert-group
Page 1126
destination-profile short-txt-destination email-addr[no] destination-profile short-txt-destination email-addr <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for short txt messageshort-txt-destination
Add email addremail-addr
Provide email address, example: [email protected]
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)982
D Commandsdestination-profile short-txt-destination email-addr
Page 1127
destination-profile short-txt-destination http[no] destination-profile short-txt-destination http <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for short txt messageshort-txt-destination
Add http or https urlhttp
Provide http or https url, example1: http://site.com/services/callservexample2: https://site2.com/serv/CALL
s0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)983
D Commandsdestination-profile short-txt-destination http
Page 1128
destination-profile short-txt-destination message-size[no] destination-profile short-txt-destination message-size <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for short txt messageshort-txt-destination
Configure maximum message size (default 4000)message-size
i0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)984
D Commandsdestination-profile short-txt-destination message-size
Page 1129
destination-profile short-txt-destination message-level[no] destination-profile short-txt-destination message-level <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for short txt messageshort-txt-destination
Callhome message level(0-lowest urgency, 9-highest urgency)message-level
i0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)985
D Commandsdestination-profile short-txt-destination message-level
Page 1130
destination-profile short-txt-destination transport-method http[no] destination-profile short-txt-destination transport-method http
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for short txt messageshort-txt-destination
Callhome message sending transport-methodtransport-method
http transport-methodhttp
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)986
D Commandsdestination-profile short-txt-destination transport-method http
Page 1131
destination-profileshort-txt-destinationtransport-methodemail[no] destination-profile short-txt-destination transport-method email
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
Configure destination profile for short txt messageshort-txt-destination
Callhome message sending transport-methodtransport-method
email transport-methodemail
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)987
D Commandsdestination-profile short-txt-destination transport-method email
Page 1132
destination-profile transport-method email[no] destination-profile <s5> transport-method email
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
User defined destination profile names5
Callhome message sending transport-methodtransport-method
email transport-methodemail
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)988
D Commandsdestination-profile transport-method email
Page 1133
destination-profile transport-method http[no] destination-profile <s6> transport-method http
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure destination profilesdestination-profile
User defined destination profile names6
Callhome message sending transport-methodtransport-method
http transport-methodhttp
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)989
D Commandsdestination-profile transport-method http
Page 1134
destination-sup interface[no] destination-sup interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Destination configurationdestination-sup
Configure interfacesinterface
interface
Command Mode
• /exec/configure/monitor-local-src /exec/configure/config-monitor/exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)990
D Commandsdestination-sup interface
Page 1135
destination{ [ no ] destination <ipaddr> } [ use-vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
Destination configurationdestination
IP Address to be configuredipaddr
(Optional) VRF labeluse-vrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure/config-ssx-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)991
D Commandsdestination
Page 1136
destination1 interface[no] destination1 interface <interface_range>
Syntax Description
(Optional) Negate a command or set its defaultsno
Destination configurationdestination1
Configure interfacesinterface
interface_range
Command Mode
• /exec/configure/monitor-local-dst
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)992
D Commandsdestination1 interface
Page 1137
destination{ [ no ] destination { <ipaddr> | <ipv6addr> } [ use-vrf { <vrf_name> | <vrf-known-name> } ] | no destination}
Syntax Description
Specify the destination addressdestination
Destination IP address for collectoripaddr
(Optional) Optional VRF labeluse-vrf
(Optional) VRF namevrf_name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure/config-int-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)993
D Commandsdestination
Page 1138
destination{ [ no ] destination { <ipaddr> | <ipv6addr> } [ use-vrf { <vrf_name> | <vrf-known-name> } ] | no destination}
Syntax Description
Specify the destination addressdestination
Destination IP address for collectoripaddr
(Optional) Optional VRF labeluse-vrf
(Optional) VRF namevrf_name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure/config-fte-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)994
D Commandsdestination
Page 1139
destination{ [ no ] destination { <ipaddr> | <ipv6addr> } [ use-vrf { <vrf_name> | <vrf-known-name> } ] | no destination}
Syntax Description
Specify the destination addressdestination
Destination IP address for collectoripaddr
(Optional) Optional VRF labeluse-vrf
(Optional) VRF namevrf_name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure/nfm-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)995
D Commandsdestination
Page 1140
destination{ [ no ] destination { <ipaddr> | <ipv6addr> } [ use-vrf { <vrf_name> | <vrf-known-name> } ] | no destination}
Syntax Description
Specify the destination addressdestination
Destination IP address for collectoripaddr
(Optional) Optional VRF labeluse-vrf
(Optional) VRF namevrf_name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure/config-postcard-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)996
D Commandsdestination
Page 1141
destination[no] destination | destination <ipaddr>
Syntax Description
Negate a command or set its defaultsno
destination of tunneldestination
ip address (A.B.C.D)ipaddr
Command Mode
• /exec/configure/if-te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)997
D Commandsdestination
Page 1142
destination filter ip[no] destination filter ip { <ip-addr> <ip-mask> } [ ip | { { udp | tcp } { <port_num> | any } } ] [ { arp |advertise } { enable | disable } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
destination ip configurationdestination
list of ips to filterfilter
destination ipip
IP address in format i.i.i.iip-addr
IP network mask in format m.m.m.mip-mask
(Optional) IP Protocolip
(Optional) UDP Protocoludp
(Optional) TCP Protocoltcp
(Optional) Port Numberport_num
(Optional) Any Port Numberany
(Optional) ARParp
(Optional) advertiseadvertise
(Optional) Enableenable
(Optional) Disabledisable
Command Mode
• /exec/configure/smartc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)998
D Commandsdestination filter ip
Page 1143
destination filter ip any any[no] destination filter ip any any
Syntax Description
(Optional) Negate a command or set its defaultsno
destination ip configurationdestination
list of ips to filterfilter
destination ipip
Any IPany
Command Mode
• /exec/configure/smartc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)999
D Commandsdestination filter ip any any
Page 1144
destination group[no] destination group <group_number>
Syntax Description
(Optional) Negate a command or set its defaultsno
Destination configurationdestination
Configure destination groupgroup
group_number
Command Mode
• /exec/configure/monitor-local-dst
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1000
D Commandsdestination group
Page 1145
destination interface[no] destination interface <interface_range>
Syntax Description
(Optional) Negate a command or set its defaultsno
Destination configurationdestination
Configure interfacesinterface
interface_range
Command Mode
• /exec/configure/monitor-local-dst
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1001
D Commandsdestination interface
Page 1146
destination ip[no] destination ip <ipaddress>
Syntax Description
(Optional) Negate a command or set its defaultsno
Destination configurationdestination
Configure remote IP addressip
ipaddress
Command Mode
• /exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1002
D Commandsdestination ip
Page 1147
device-group[no] device-group <group-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
PLB device groupdevice-group
Specify device-group namegroup-name
Command Mode
• /exec/configure/plb
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1003
D Commandsdevice-group
Page 1148
device-group{ device-group <name> } | { no device-group <name> }
Syntax Description
Negate a command or set its defaultsno
ITD device groupdevice-group
ITD device group namename
Command Mode
• /exec/configure/itd
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1004
D Commandsdevice-group
Page 1149
device-role[no] device-role <dev_role>
Syntax Description
(Optional) Negate a command or set its defaultsno
dev_role
Command Mode
• /exec/configure/config-snoop-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1005
D Commandsdevice-role
Page 1150
device-role[no] device-role <devrole>
Syntax Description
(Optional) Negate a command or set its defaultsno
devrole
Command Mode
• /exec/configure/config-dhcp-guard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1006
D Commandsdevice-role
Page 1151
device-role[no] device-role <dev_role>
Syntax Description
(Optional) Negate a command or set its defaultsno
dev_role
Command Mode
• /exec/configure/config-ra-guard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1007
D Commandsdevice-role
Page 1152
dfe-tuning-delay{ dfe-tuning-delay <delay-val> | no dfe-tuning-delay [ <delay-val> ] }
Syntax Description
Negate a command or set its defaultsno
Configure DFE Tuning delay for interfacedfe-tuning-delay
DFE tuning delay value (ms)delay-val
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1008
D Commandsdfe-tuning-delay
Page 1153
diagnostic bootup level[no] diagnostic bootup level
Syntax Description
Negate a command or set its defaultsno
Diagnostic commandsdiagnostic
Configure Diagnostic for bootupbootup
Select diagnostic levellevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1009
D Commandsdiagnostic bootup level
Page 1154
diagnostic bootup level bypassdiagnostic bootup level { bypass | complete }
Syntax Description
Diagnostic commandsdiagnostic
Configure Diagnostic for bootupbootup
Select diagnostic levellevel
Skip all bootup testbypass
Complete levelcomplete
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1010
D Commandsdiagnostic bootup level bypass
Page 1155
diagnostic clear result module all diagnostic clear resultmodule test
diagnostic clear result module all | diagnostic clear result module <module> test { <test-id> | all }
Syntax Description
Diagnostic commandsdiagnostic
Erase Diagnostic Test Results/Statsclear
Diagnostic test resultresult
Module keywordmodule
Module numbermodule
Select allall
Diagnostic test selectiontest
test-id
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1011
D Commandsdiagnostic clear result module all diagnostic clear result module test
Page 1156
diagnostic monitor interval module test all hour min seconddiagnostic monitor interval module <module> test { all | <name> | <test-id> } hour <hour-cntr>min <min-cntr>second <sec-cntr> | no diagnostic monitor interval module <module> test { all | <name> | <test-id> }
Syntax Description
Negate a command or set its defaultsno
Diagnostic commandsdiagnostic
Configure diagnostic monitoring testmonitor
Configure diagnostic monitoring tests intervalinterval
Module Keywordmodule
Module numbermodule
Diagnostic test selectiontest
Select all test IDall
test-id
Test namename
Hour of the dayhour
Interval in hourshour-cntr
Minute of an hourmin
Interval in minutesmin-cntr
Second of a minutesecond
Interval in secondssec-cntr
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1012
D Commandsdiagnostic monitor interval module test all hour min second
Page 1157
diagnostic monitor module test alldiagnostic monitor module <module> test { all | <name> | <test-id> } | no diagnostic monitor module <module>test { all | <name> | <test-id> }
Syntax Description
Negate a command or set its defaultsno
Diagnostic commandsdiagnostic
Configure diagnostic monitoring testmonitor
Module Keywordmodule
Module numbermodule
Diagnostic test selectiontest
Select all test IDall
test-id
Test namename
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1013
D Commandsdiagnostic monitor module test all
Page 1158
diagnostic ondemand action-on-failure continue failure-countdiagnostic ondemand action-on-failure stop
diagnostic ondemand action-on-failure continue failure-count <failure-cnt> | diagnostic ondemandaction-on-failure stop
Syntax Description
Diagnostic commandsdiagnostic
On demand diagnostic settingondemand
Set action to take if test failsaction-on-failure
Continue ondemand test until test failure limit is reachedcontinue
Continue failing tests this many timesfailure-count
Stop ondemand tests immediately if a test failsstop
Maximum number of test failures allowedfailure-cnt
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1014
D Commandsdiagnostic ondemand action-on-failure continue failure-count diagnostic ondemand action-on-failure stop
Page 1159
diagnostic ondemand iterationdiagnostic ondemand iteration <iteration-count>
Syntax Description
Diagnostic commandsdiagnostic
On demand diagnostic settingondemand
Set number of times to repeat ondemand test listiteration
Number of times to repeat ondemand test listiteration-count
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1015
D Commandsdiagnostic ondemand iteration
Page 1160
diagnostic ondemand test-parameter module test port_lbpacket-length
diagnostic ondemand test-parameter module <module> test port_lb packet-length <size>
Syntax Description
Diagnostic commandsdiagnostic
Ondemand commandondemand
Set test parametertest-parameter
Module keywordmodule
Module numbermodule
Diagnostic test selectiontest
Port loop back testport_lb
Size of the packetpacket-length
Packet size for the selected modulesize
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1016
D Commandsdiagnostic ondemand test-parameter module test port_lb packet-length
Page 1161
diagnostic start module testdiagnostic start module <module> test { all | <name> | <test-id> | non-disruptive | per-port } [ port { iall |<port-id> } ]
Syntax Description
Diagnostic commandsdiagnostic
Starting on demand diagnosticstart
Module keywordmodule
Module Numbermodule
Diagnostic test selectiontest
Select all test IDall
Test namename
test-id
Select the Non-Disruptive test suite [Attribute = N]non-disruptive
Select the Per-Port test suite [Attribute = P]per-port
(Optional) Interface port selectionport
(Optional) Select all portsiall
(Optional)port-id
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1017
D Commandsdiagnostic start module test
Page 1162
diagnostic stop module test alldiagnostic stop module <module> test { all | <name> | <test-id> }
Syntax Description
Diagnostic commandsdiagnostic
Stopping diagnosticstop
Module keywordmodule
Module Numbermodule
Diagnostic test selectiontest
Select all test IDall
test-id
Test namename
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1018
D Commandsdiagnostic stop module test all
Page 1163
diagnostictestsimulationmoduletestdiagnostictestsimulationmodule test clear
diagnostic test simulationmodule <module> test <test-id> [ port { <port-id> | all } ] { success | fail | random-fail} | diagnostic test simulation module <module> test <test-id> clear
Syntax Description
Diagnostic commandsdiagnostic
Diagnostic test selectiontest
Simulating Diagnostic resultsimulation
Module keywordmodule
Module Numbermodule
Diagnostic test selectiontest
test-id
(Optional) Interface port selectionport
(Optional) Select all portsall
(Optional)port-id
pass test resultsuccess
fail test resultfail
fail test result randomlyrandom-fail
Stop simulationclear
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1019
D Commandsdiagnostic test simulation module test diagnostic test simulation module test clear
Page 1164
diff-cleandiff-clean [ all-sessions ]
Syntax Description
remove temp files created by '| diff' filtersdiff-clean
(Optional) remove '| diff' temp files from all sessions (past and present!)of current user
all-sessions
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1020
D Commandsdiff-clean
Page 1165
diff-clean all-usersdiff-clean all-users
Syntax Description
remove temp files created by '| diff' filtersdiff-clean
remove '| diff' temp files from all sessions (past and present!) of all usersall-users
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1021
D Commandsdiff-clean all-users
Page 1166
diff| diff [ again | echo | -c [ <lines> ] | -b | -B | -i | -I <regexp> | -y | --left-column | -W <columns> | -q | -s ] +
Syntax Description
Pipe command output to filter|
show difference between current and previous invocation (creates tempfiles: remove them with 'diff-clean' command and dont use it oncommands with big outputs, like 'show tech'!)
diff
(Optional) dont create new file: use old ones, just change display optionsor add more filters
again
(Optional) echo the current file (only effective if no old file)echo
(Optional) set number of lines of context (default 3)-c
(Optional) number of lines of contextlines
(Optional) Ignore changes in amount of white space-b
(Optional) Ignore changes that just insert or delete blank lines-B
(Optional) Ignore changes in case-i
(Optional) Ignore changes that just insert or delete lines that matchregexp
-I
(Optional) regexp of lines to ignoreregexp
(Optional) Use the side by side output format-y
(Optional) Print only the left column of two common lines in side byside format
--left-column
(Optional) Use an output width of <columns> in side by side format-W
(Optional) Use an output width of <columns> in side by side formatcolumns
(Optional) Report only whether the files differ, not the details of thedifferences
-q
(Optional) Report when two files are the same-s
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1022
D Commandsdiff
Page 1167
dirdir [ <uri0> | <uri1> | <uri2> ] [ __readonly__ { TABLE_dir <fsize> <timestring> <fname> } { <usage><bytesused> <bytesfree> <bytestotal> } ]
Syntax Description
list files in a directorydir
(Optional) Directory or filenameuri0
(Optional) Directory or filename on expansion flashuri1
(Optional) Directory or filename on log flashuri2
(Optional) Read Only__readonly__
(Optional) show dirTABLE_dir
(Optional) filesizefsize
(Optional) time stringtimestring
(Optional) filenamefname
(Optional) usageusage
(Optional) bytes usedbytesused
(Optional) bytes freebytesfree
(Optional) bytes totalbytestotal
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1023
D Commandsdir
Page 1168
disable-connected-check[ no | default ] disable-connected-check
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Disable check for directly connected peerdisable-connected-check
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1024
D Commandsdisable-connected-check
Page 1169
disable-fka[no] disable-fka
Syntax Description
(Optional) Negate a command or set its defaultsno
Disables verifying FIP Keep Alivesdisable-fka
Command Mode
• /exec/configure/if-vfc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1025
D Commandsdisable-fka
Page 1170
disable-peer-as-check[ no | default ] disable-peer-as-check
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Disable checking of peer AS-number while advertisingdisable-peer-as-check
Command Mode
• /exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv4/exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1026
D Commandsdisable-peer-as-check
Page 1171
disable-policy-batching[no] disable-policy-batching [ nexthop | { { ipv4 | ipv6 } prefix-list <prfxlist-name> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Disable batching evaluation of outbound policy for a peerdisable-policy-batching
(Optional) batching based on nexthopnexthop
(Optional) IPv4 address-familyipv4
(Optional) IPv6 address-familyipv6
(Optional) Apply prefix-listprefix-list
(Optional) Name of prefix-listprfxlist-name
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1027
D Commandsdisable-policy-batching
Page 1172
disabledisable
Syntax Description
disable callhomedisable
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1028
D Commandsdisable
Page 1173
discard-route external[no] discard-route { external | internal }
Syntax Description
(Optional) Negate a command or set its defaultsno
Install discard routediscard-route
External routeexternal
Internal routeinternal
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1029
D Commandsdiscard-route external
Page 1174
discard-route external[no] discard-route { external | internal }
Syntax Description
(Optional) Negate a command or set its defaultsno
Install discard routediscard-route
External routeexternal
Internal routeinternal
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1030
D Commandsdiscard-route external
Page 1175
discoverydiscovery { quick-start | hello { holdtime <link-hello-holdtime> | interval <link-hello-intvl> } | targeted-hello{ accept [ from <pfx-list> ] | tgt-holdtime <tgt-hello-holdtime> | tgt-interval <tgt-hello-intvl> } |ignore-transport-address | omit-transport-address | spoofing } | no discovery { quick-start | hello { holdtime |interval } | targeted-hello { accept | tgt-holdtime | tgt-interval } | ignore-transport-address | omit-transport-address| spoofing }
Syntax Description
Negate a command or set its defaultsno
LDP discoverydiscovery
Enable quick LDP Hello transmissions on interface upquick-start
LDP discovery Hellohello
LDP discovery Hello intervalinterval
LDP discovery Hello holdtimeholdtime
Holdtime in secondslink-hello-holdtime
Hello interval in secondslink-hello-intvl
LDP discovery Targeted Hellotargeted-hello
Accept targeted hellosaccept
(Optional) Prefix list to specify acceptable targeted hello sourcesfrom
(Optional) Name of prefix listpfx-list
LDP discovery Targeted Hello holdtimetgt-holdtime
Holdtime in secondstgt-hello-holdtime
LDP discovery Targeted Hello intervaltgt-interval
Hello interval in secondstgt-hello-intvl
ignore-transport-address
omit-transport-address
spoofing
Command Mode
• /exec/configure/ldp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1031
D Commandsdiscovery
Page 1176
distancedistance <admin-dist> | no distance [ <admin-dist> ]
Syntax Description
Negate a command or set its defaultsno
OSPFv3 administrative distancedistance
adminitrative distance valueadmin-dist
Command Mode
• /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1032
D Commandsdistance
Page 1177
distancedistance <distance> | no distance [ <distance> ]
Syntax Description
Negate a command or set its defaultsno
RIP administrative distancedistance
RIP administrative distancedistance
Command Mode
• /exec/configure/router-rip/router-rip-af-common /exec/configure/router-rip/router-rip-vrf-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1033
D Commandsdistance
Page 1178
distancedistance <admin-dist> | no distance [ <admin-dist> ]
Syntax Description
Negate a command or set its defaultsno
Administrative distancedistance
Distance valueadmin-dist
Command Mode
• /exec/configure/router-isis/router-isis-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1034
D Commandsdistance
Page 1179
distancedistance <admin-dist> | no distance [ <admin-dist> ]
Syntax Description
Negate a command or set its defaultsno
Administrative distancedistance
Distance valueadmin-dist
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1035
D Commandsdistance
Page 1180
distance{ { distance <int-distance> <ext-distance> } | { no distance [ <int-distance> <ext-distance> ] } }
Syntax Description
Negate a command or set its defaultsno
Define an administrative distancedistance
Distance for internal routesint-distance
Distance for external routesext-distance
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1036
D Commandsdistance
Page 1181
distancedistance <admin-dist> | no distance [ <admin-dist> ]
Syntax Description
Negate a command or set its defaultsno
OSPF administrative distancedistance
adminitrative distance valueadmin-dist
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1037
D Commandsdistance
Page 1182
distancedistance <ebgp-dist> <ibgp-dist> <local-dist> | no distance [ <ebgp-dist> <ibgp-dist> <local-dist> ]
Syntax Description
Negate a command or set its defaultsno
Configure administrative distancedistance
Distance for EBGP routesebgp-dist
Distance for IBGP routesibgp-dist
Distance for local routeslocal-dist
Command Mode
• /exec/configure/router-bgp/router-bgp-af
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1038
D Commandsdistance
Page 1183
distribute into route-map all{ { distribute <src-level> into <dst-level> { { route-map { <map-name> | <rtr_pol_name> } } | all } } | { nodistribute <src-level> into <dst-level> [ { route-map { <map-name> | <rtr_pol_name> } } | all ] } }
Syntax Description
Negate a command or set its defaultsno
Distribute routes between ISIS levelsdistribute
Route-distribution between levelssrc-level
Route-distribution between levelsdst-level
Route Map to constrain distributionroute-map
from level-n into level-minto
A 'routing-rules' route-map namemap-name
An existing routing-rules policyrtr_pol_name
Distribute all level-n routesall
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common /exec/configure/router-isis/router-isis-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1039
D Commandsdistribute into route-map all
Page 1184
distribute link-state[no] distribute link-state [ instance-id <instid> ] [ level <level> ] [ throttle <seconds> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Distribute routes between ISIS levelsdistribute
Distribute link-statelink-state
(Optional) Instance ID of ISIS processinstance-id
(Optional) Instance ID of ISIS processinstid
(Optional) Level to be distributedlevel
(Optional) IS-IS levellevel
(Optional) Throttle timer in secondsthrottle
(Optional) Throttle timer in secondsseconds
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1040
D Commandsdistribute link-state
Page 1185
dns[no] dns { <WORD> } { name-server { <hostname> | <ip-address> } } { [ source-ip { <source-ip-hostname>| <source-ip-address> } ] | [ source-port <src-port> ] } +
Syntax Description
(Optional)no
(Optional) source-portsource-ip
(Optional)src-port
DNS Operationdns
Target IP Address or HostnameWORD
Name Servername-server
Destination hostname, broadcast disallowedhostname
Destination IP address, broadcast disallowedip-address
(Optional) source IP hostname, broadcast disallowedsource-ip-hostname
(Optional) source IP address, broadcast disallowedsource-ip-address
(Optional) Source Portsource-port
Command Mode
• /exec/configure/ip-sla
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1041
D Commandsdns
Page 1186
domain-iddomain-id { <id> | { type <dtype> value <dvalue> } | Null } | no domain-id [ <id> | { type <dtype> value<dvalue> } | Null ]
Syntax Description
Negate a command or set its defaultsno
OSPF domain-IDdomain-id
OSPF domain ID in IP address formatid
OSPF domain ID type in Hex formattype
OSPF domain ID type in Hex formatdtype
OSPF domain ID ext. community value in Hexvalue
dvalue
Null Domain-IDNull
Command Mode
• /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1042
D Commandsdomain-id
Page 1187
domain-id secondarydomain-id { <id> | { type <dtype> value <dvalue> } | Null } secondary | no domain-id [ <id> | { type <dtype>value <dvalue> } | Null ] secondary
Syntax Description
Negate a command or set its defaultsno
OSPF domain-IDdomain-id
OSPF domain ID in IP address formatid
OSPF domain ID type in Hex formattype
OSPF domain ID type in Hex formatdtype
OSPF domain ID ext. community value in Hexvalue
dvalue
Null Domain-IDNull
Secondary Domain-IDsecondary
Command Mode
• /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1043
D Commandsdomain-id secondary
Page 1188
domain-tag[no] domain-tag <as-number>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set OSPF process domain-tagdomain-tag
AS numberas-number
Command Mode
• /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1044
D Commandsdomain-tag
Page 1189
dont-capability-negotiate[ no | default ] dont-capability-negotiate
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Don't negotiate capability with this neighbordont-capability-negotiate
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1045
D Commandsdont-capability-negotiate
Page 1190
dos2nxosdos2nxos <uri0>
Syntax Description
DOS to NXOS text file format converterdos2nxos
Filename to be displayeduri0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1046
D Commandsdos2nxos
Page 1191
dot1q{ dot1q <vlan-id> [ cos <cos-val> ] } | { no dot1q }
Syntax Description
Negate a command or set its defaultsno
specify flow profile to include dot1q tagdot1q
specify flow profile vlan-idvlan-id
(Optional) specify class of servicecos
(Optional) class of service valuecos-val
Command Mode
• /exec/configure/configngoamprofileflow
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1047
D Commandsdot1q
Page 1192
dot1q[no] dot1q <vlan-id-sh>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a dot1q-based static hostdot1q
vlan-id-sh
Command Mode
• /exec/configure/static-host
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1048
D Commandsdot1q
Page 1193
dot1q{ dot1q <dot1q-id> [ <intf-id> ] } | { no dot1q }
Syntax Description
Negate a command or set its defaultsno
Encapsulation dot1q/bddot1q
Encapsulation dot1q/bd valuedot1q-id
(Optional) Name of the interface for ngoam onwhich dot1q is configuredintf-id
Command Mode
• /exec/configure/configngoamprofile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1049
D Commandsdot1q
Page 1194
dot1q default dynamic{ dot1q default dynamic } | { no dot1q default }
Syntax Description
Negate a command or set its defaultsno
Dynamic Profile Map: Retrieve profile name from the external serverdynamic
Dot1Q Encapsulationdot1q
Default (wildcard). Match any dot1q when there is no specific dot1qmapping configured
default
Command Mode
• /exec/configure/profile-map /exec/configure/profile-map-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1050
D Commandsdot1q default dynamic
Page 1195
dot1x defaultdot1x default
Syntax Description
dot1x configuration commandsdot1x
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1051
D Commandsdot1x default
Page 1196
dot1x defaultdot1x default
Syntax Description
dot1x configuration commandsdot1x
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1052
D Commandsdot1x default
Page 1197
dot1x host-modedot1x host-mode <host_mode> | no dot1x host-mode
Syntax Description
dot1x configuration commandsdot1x
role of 802.1x authenticating entityhost-mode
Host Modehost_mode
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1053
D Commandsdot1x host-mode
Page 1198
dot1x initialize{ dot1x initialize } | { dot1x initialize interface <if> }
Syntax Description
dot1x configuration commandsdot1x
Initialize State Machines for a given Interfaceinitialize
target interfaceif
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1054
D Commandsdot1x initialize
Page 1199
dot1x mac-auth-bypassdot1x mac-auth-bypass [ eap ] | no dot1x mac-auth-bypass
Syntax Description
Negate a command or set its defaultsno
dot1x configuration commandsdot1x
Configure Mac-Auth-Bypassmac-auth-bypass
(Optional) EAP Authenticationeap
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1055
D Commandsdot1x mac-auth-bypass
Page 1200
dot1x mac-movedot1x mac-move <value> | no dot1x mac-move <value>
Syntax Description
dot1x configuration commandsdot1x
Enable or Disable Mac-movesmac-move
Mac Movevalue
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1056
D Commandsdot1x mac-move
Page 1201
dot1x max-reauth-reqdot1x max-reauth-req <count> | no dot1x max-reauth-req
Syntax Description
dot1x configuration commandsdot1x
Maximum Re-authentication Attempts Before Failingmax-reauth-req
number of retriescount
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1057
D Commandsdot1x max-reauth-req
Page 1202
dot1x max-reqdot1x max-req <count> | no dot1x max-req
Syntax Description
dot1x configuration commandsdot1x
Maximum Retries to Initiate Authenticationmax-req
number of retriescount
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1058
D Commandsdot1x max-req
Page 1203
dot1x pae[no] dot1x pae <pae-value>
Syntax Description
dot1x configuration commandsdot1x
role of 802.1x authenticating entitypae
rolepae-value
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1059
D Commandsdot1x pae
Page 1204
dot1x port-control[no] dot1x port-control <port-control-value>
Syntax Description
dot1x configuration commandsdot1x
port controlport-control
set the port-control valueport-control-value
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1060
D Commandsdot1x port-control
Page 1205
dot1x radius-accounting[no] dot1x radius-accounting
Syntax Description
dot1x configuration commandsdot1x
accounting messages to RADIUSradius-accounting
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1061
D Commandsdot1x radius-accounting
Page 1206
dot1x re-authenticate interfacedot1x re-authenticate interface <if>
Syntax Description
dot1x configuration commandsdot1x
Manually re-authenticate an Interfacere-authenticate
target interfaceif
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1062
D Commandsdot1x re-authenticate interface
Page 1207
dot1x re-authentication[no] dot1x re-authentication
Syntax Description
dot1x configuration commandsdot1x
Enable or Disable Reauthentication for this portre-authentication
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1063
D Commandsdot1x re-authentication
Page 1208
dot1x re-authentication[no] dot1x re-authentication
Syntax Description
dot1x configuration commandsdot1x
Enable or Disable Reauthentication for this portre-authentication
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1064
D Commandsdot1x re-authentication
Page 1209
dot1x show credentialdot1x show credential <name>
Syntax Description
dot1x configuration commandsdot1x
supplicant credential profilecredential
profile namename
Command Mode
• /exec/configure/dot1x-cred
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1065
D Commandsdot1x show credential
Page 1210
dot1x start supplicant interface{ dot1x start supplicant interface <if> } | { dot1x start supplicant interface <if> credential <name> }
Syntax Description
dot1x configuration commandsdot1x
start 802.1x clientstart
802.1x supplicantsupplicant
target interfaceif
credential profile namecredential
namename
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1066
D Commandsdot1x start supplicant interface
Page 1211
dot1x supplicant credential[no] dot1x supplicant credential <name>
Syntax Description
dot1x configuration commandsdot1x
802.1x supplicantsupplicant
supplicant credential profilecredential
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1067
D Commandsdot1x supplicant credential
Page 1212
dot1x supplicant credential[no] dot1x supplicant credential <name>
Syntax Description
dot1x configuration commandsdot1x
802.1x supplicantsupplicant
credential profile namecredential
namename
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1068
D Commandsdot1x supplicant credential
Page 1213
dot1x supplicant max-start[no] dot1x supplicant max-start <count>
Syntax Description
dot1x configuration commandsdot1x
802.1x supplicantsupplicant
Maximum Start Requestsmax-start
numbercount
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1069
D Commandsdot1x supplicant max-start
Page 1214
dot1x supplicant max-start[no] dot1x supplicant max-start <count>
Syntax Description
dot1x configuration commandsdot1x
802.1x supplicantsupplicant
Maximum Start Requestsmax-start
numbercount
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1070
D Commandsdot1x supplicant max-start
Page 1215
dot1x supplicant timeout auth-period[no] dot1x supplicant timeout auth-period <value>
Syntax Description
dot1x configuration commandsdot1x
802.1x supplicantsupplicant
Various Timeoutstimeout
waiting period for responses from authenticatorauth-period
time interval in secondsvalue
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1071
D Commandsdot1x supplicant timeout auth-period
Page 1216
dot1x supplicant timeout auth-period[no] dot1x supplicant timeout auth-period <value>
Syntax Description
dot1x configuration commandsdot1x
802.1x supplicantsupplicant
Various Timeoutstimeout
waiting period for responses from authenticatorauth-period
time interval in secondsvalue
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1072
D Commandsdot1x supplicant timeout auth-period
Page 1217
dot1x supplicant timeout held-period[no] dot1x supplicant timeout held-period <value>
Syntax Description
dot1x configuration commandsdot1x
802.1x supplicantsupplicant
Various Timeoutstimeout
waiting period for retrying, after failed authenticationheld-period
time interval in secondsvalue
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1073
D Commandsdot1x supplicant timeout held-period
Page 1218
dot1x supplicant timeout held-period[no] dot1x supplicant timeout held-period <value>
Syntax Description
dot1x configuration commandsdot1x
802.1x supplicantsupplicant
Various Timeoutstimeout
waiting period for retrying, after failed authenticationheld-period
time interval in secondsvalue
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1074
D Commandsdot1x supplicant timeout held-period
Page 1219
dot1x supplicant timeout start-period[no] dot1x supplicant timeout start-period <value>
Syntax Description
dot1x configuration commandsdot1x
802.1x supplicantsupplicant
Various Timeoutstimeout
Interval Between Start Requestsstart-period
time interval in secondsvalue
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1075
D Commandsdot1x supplicant timeout start-period
Page 1220
dot1x supplicant timeout start-period[no] dot1x supplicant timeout start-period <value>
Syntax Description
dot1x configuration commandsdot1x
802.1x supplicantsupplicant
Various Timeoutstimeout
Interval Between Start Requestsstart-period
time interval in secondsvalue
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1076
D Commandsdot1x supplicant timeout start-period
Page 1221
dot1x system-auth-control[no] dot1x system-auth-control
Syntax Description
dot1x configuration commandsdot1x
Enable or Disable SysAuthControlsystem-auth-control
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1077
D Commandsdot1x system-auth-control
Page 1222
dot1x timeout inactivity-perioddot1x timeout inactivity-period <value> | no dot1x timeout inactivity-period
Syntax Description
dot1x configuration commandsdot1x
Various Timeoutstimeout
Timeout For Session Inactivityinactivity-period
time interval in secondsvalue
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1078
D Commandsdot1x timeout inactivity-period
Page 1223
dot1x timeout inactivity-perioddot1x timeout inactivity-period <value> | no dot1x timeout inactivity-period
Syntax Description
dot1x configuration commandsdot1x
Various Timeoutstimeout
Timeout For Session Inactivityinactivity-period
time interval in secondsvalue
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1079
D Commandsdot1x timeout inactivity-period
Page 1224
dot1x timeout quiet-perioddot1x timeout quiet-period <value> | no dot1x timeout quiet-period
Syntax Description
dot1x configuration commandsdot1x
Various Timeoutstimeout
Timeout For Retrying Authentication After Failed Authenticationquiet-period
time interval in secondsvalue
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1080
D Commandsdot1x timeout quiet-period
Page 1225
dot1x timeout quiet-perioddot1x timeout quiet-period <value> | no dot1x timeout quiet-period
Syntax Description
dot1x configuration commandsdot1x
Various Timeoutstimeout
Timeout For Retrying Authentication After Failed Authenticationquiet-period
time interval in secondsvalue
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1081
D Commandsdot1x timeout quiet-period
Page 1226
dot1x timeout ratelimit-perioddot1x timeout ratelimit-period <value> | no dot1x timeout ratelimit-period
Syntax Description
dot1x configuration commandsdot1x
Various Timeoutstimeout
Rate Limit period for EAPOL-Startratelimit-period
time interval in secondsvalue
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1082
D Commandsdot1x timeout ratelimit-period
Page 1227
dot1x timeout re-authperioddot1x timeout re-authperiod <value> | no dot1x timeout re-authperiod
Syntax Description
dot1x configuration commandsdot1x
Various Timeoutstimeout
Timeout For Re-Authenticationre-authperiod
time interval in secondsvalue
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1083
D Commandsdot1x timeout re-authperiod
Page 1228
dot1x timeout re-authperioddot1x timeout re-authperiod <value> | no dot1x timeout re-authperiod
Syntax Description
dot1x configuration commandsdot1x
Various Timeoutstimeout
Timeout For Re-Authenticationre-authperiod
time interval in secondsvalue
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1084
D Commandsdot1x timeout re-authperiod
Page 1229
dot1x timeout server-timeoutdot1x timeout server-timeout <value> | no dot1x timeout server-timeout
Syntax Description
dot1x configuration commandsdot1x
Various Timeoutstimeout
Timeout for Radius Retriesserver-timeout
time interval in secondsvalue
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1085
D Commandsdot1x timeout server-timeout
Page 1230
dot1x timeout supp-timeoutdot1x timeout supp-timeout <value> | no dot1x timeout supp-timeout
Syntax Description
dot1x configuration commandsdot1x
Various Timeoutstimeout
Timeout for Supplicant retriessupp-timeout
time interval in secondsvalue
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1086
D Commandsdot1x timeout supp-timeout
Page 1231
dot1x timeout tx-perioddot1x timeout tx-period <value> | no dot1x timeout tx-period
Syntax Description
dot1x configuration commandsdot1x
Various Timeoutstimeout
Timeout For Resending Requests To Supplicanttx-period
time interval in secondsvalue
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1087
D Commandsdot1x timeout tx-period
Page 1232
dot1x timeout tx-perioddot1x timeout tx-period <value> | no dot1x timeout tx-period
Syntax Description
dot1x configuration commandsdot1x
Various Timeoutstimeout
Timeout For Resending Requests To Supplicanttx-period
time interval in secondsvalue
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1088
D Commandsdot1x timeout tx-period
Page 1233
down-bit-ignore{ down-bit-ignore } | { no down-bit-ignore }
Syntax Description
Negate a command or set its defaultsno
Configure a PE router to ignore the DN bit for network summary,external and NSSA external LSA
down-bit-ignore
Command Mode
• /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1089
D Commandsdown-bit-ignore
Page 1234
downlink delaydownlink delay <ena-dis-flg> [ timeout <time-out> ] | no downlink delay
Syntax Description
Negate a command or set its defaultsno
Change downlink linkup timedownlink
delay bringup of downlinksdelay
Enable/Disable downlink delay featureena-dis-flg
(Optional) downlink ports enable delay in secondstimeout
(Optional) Time outtime-out
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1090
D Commandsdownlink delay
Page 1235
dpp set-qos-group[no] dpp set-qos-group <qos-group>
Syntax Description
(Optional) Negate a command or set its defaultsno
Dynamic Packet Prioritizationdpp
QoS group to be mappedset-qos-group
QoS Group Valueqos-group
Command Mode
• /exec/configure/policy-map/type/uf/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1091
D Commandsdpp set-qos-group
Page 1236
drop-trigger[no] drop-trigger { ingress-admission | egress-admission | wred }
Syntax Description
(Optional) Negate the commandno
Configure drop-trigger parametersdrop-trigger
Ingress Admission Dropingress-admission
Egress Admission Dropegress-admission
Weighted Random Early Discard Dropwred
Command Mode
• /exec/configure/pkt-drop
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1092
D Commandsdrop-trigger
Page 1237
droplist[no] droplist <droplistname>
Syntax Description
Specify POSTCARD droplist to usedroplist
Name of droplistdroplistname
Command Mode
• /exec/configure/config-postcard-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1093
D Commandsdroplist
Page 1238
droplist[no] droplist <droplistname>
Syntax Description
Specify INT droplist to usedroplist
Name of droplistdroplistname
Command Mode
• /exec/configure/config-int-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1094
D Commandsdroplist
Page 1239
dscp{ [ no ] dscp <dscp> | no dscp }
Syntax Description
Optional DSCPdscp
Differentiated services codepoint valuedscp
Command Mode
• /exec/configure/config-int-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1095
D Commandsdscp
Page 1240
dscp{ [ no ] dscp <dscp> | no dscp }
Syntax Description
Provide the dscp value for this INT flow-profiledscp
flow-profile dscp (allowed values: 1, 2, 4, 8, 16, 32, 63). Default is 1dscp
Command Mode
• /exec/configure/config-int-flow-prof
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1096
D Commandsdscp
Page 1241
dscp{ [ no ] dscp <dscp> | no dscp }
Syntax Description
Optional DSCPdscp
Differentiated services codepoint valuedscp
Command Mode
• /exec/configure/nfm-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1097
D Commandsdscp
Page 1242
dscp[no] dscp <dscp>
Syntax Description
DSCPdscp
DSCP to be configureddscp
Command Mode
• /exec/configure/config-ssx-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1098
D Commandsdscp
Page 1243
dscp{ [ no ] dscp <dscp> | no dscp }
Syntax Description
Optional DSCPdscp
Differentiated services codepopostcard valuedscp
Command Mode
• /exec/configure/config-postcard-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1099
D Commandsdscp
Page 1244
dscp{ [ no ] dscp <dscp> | no dscp }
Syntax Description
Provide the dscp value for this POSTCARD flow-profiledscp
flow-profile dscp (allowed values: 1, 2, 4, 8, 16, 32, 63). Default is 1dscp
Command Mode
• /exec/configure/config-postcard-flow-prof
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1100
D Commandsdscp
Page 1245
dst-grp[no] dst-grp <d-grp-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Associated destination groupdst-grp
Identifierd-grp-id
Command Mode
• /exec/configure/telemetry/subscription
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1101
D Commandsdst-grp
Page 1246
dual-active exclude interface-vlandual-active exclude interface-vlan <allow-vlans> | no dual-active exclude interface-vlan
Syntax Description
Negate a command or set its defaultsno
Configuration when peer link is down but peer is alivedual-active
Interface vlan configurationinterface-vlan
Interface vlans to exclude from suspension when dual-activeexclude
Set allowed interface vlansallow-vlans
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1102
D Commandsdual-active exclude interface-vlan
Page 1247
duplexduplex <duplex_mode> | no duplex [ <duplex_mode> ]
Syntax Description
Negate a command or set its defaultsno
Enter the port duplex modeduplex
Interface duplex modeduplex_mode
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1103
D Commandsduplex
Page 1248
duplexduplex <duplex_mode> | no duplex [ <duplex_mode> ]
Syntax Description
Negate a command or set its defaultsno
Enter the port duplex modeduplex
Interface duplex modeduplex_mode
Command Mode
• /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1104
D Commandsduplex
Page 1249
duplicate-message throttle[no] duplicate-message throttle
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure throttling of duplicate callhome alert messagesduplicate-message
Enable throttling of duplicate callhome alert messagesthrottle
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1105
D Commandsduplicate-message throttle
Page 1250
dynamic-capability[ no | default ] dynamic-capability
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Dynamic capabilitydynamic-capability
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1106
D Commandsdynamic-capability
Page 1251
dynamic-med-interval[no] dynamic-med-interval <sec>
Syntax Description
(Optional) Negate a command or set its defaultsno
Sets the interval for dampening of med changesdynamic-med-interval
Time interval in secondssec
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1107
D Commandsdynamic-med-interval
Page 1252
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1108
D Commandsdynamic-med-interval
Page 1253
E Commands
• eapol mac-address, on page 1116• ebgp-multihop, on page 1117• echo, on page 1118• echo, on page 1119• ecp max-retries, on page 1120• ecp mode lan, on page 1121• ecp retransmission-timer-exponent, on page 1122• eem test, on page 1123• eemtest policy-add, on page 1124• eemtest policy-remove, on page 1125• egress-engineering, on page 1126• egress, on page 1127• eid-prefix, on page 1128• eigrp event-history cli size, on page 1129• eigrp file-debug, on page 1130• email-addr, on page 1131• email-contact, on page 1132• email, on page 1133• email, on page 1134• enable, on page 1135• enable, on page 1136• enable Cert, on page 1137• encapsulation dot1q, on page 1138• encapsulation dot1q, on page 1139• encrypt pause-frame, on page 1140• encryption decrypt type6, on page 1141• encryption delete type6, on page 1142• encryption re-encrypt obfuscated, on page 1143• end, on page 1144• endpoint, on page 1145• enforce-first-as, on page 1146• enrollment terminal, on page 1147• errdisable, on page 1148
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1109
Page 1254
• errdisable detect cause, on page 1149• errdisable detect cause acl-exception, on page 1150• errdisable port detect cause acl-exception, on page 1151• errdisable recovery interval, on page 1152• erspan-id, on page 1153• ethanalyzer local, on page 1154• ethernet-segment, on page 1155• ethernet-segment delay-restore time, on page 1156• ethernet-tag encapsulation dot1q default static, on page 1157• ethernet-tag encapsulation dot1q static, on page 1158• ethernet-tag encapsulation vni default static, on page 1159• ethernet-tag encapsulation vni static, on page 1160• evb mac, on page 1161• evb reinit-keep-alive, on page 1162• evb resource-wait-delay, on page 1163• event-history, on page 1164• event-history acllog category all, on page 1165• event-history acllog category all, on page 1166• event-history acllog category fc2, on page 1167• event-history acllog category fc2, on page 1168• event-history acllog category mts, on page 1169• event-history acllog category mts, on page 1170• event-history adbm category all, on page 1171• event-history adbm category all, on page 1172• event-history adbm category fc2, on page 1173• event-history adbm category fc2, on page 1174• event-history adbm category mts, on page 1175• event-history adbm category mts, on page 1176• event-history callhome, on page 1177• event-history capability, on page 1178• event-history cli, on page 1179• event-history copp category all, on page 1180• event-history copp category all, on page 1181• event-history copp category fc2, on page 1182• event-history copp category fc2, on page 1183• event-history copp category mts, on page 1184• event-history copp category mts, on page 1185• event-history dot1x, on page 1186• event-history drap category all, on page 1187• event-history drap category all, on page 1188• event-history drap category mts, on page 1189• event-history drap category mts, on page 1190• event-history eltm category all, on page 1191• event-history eltm category all, on page 1192• event-history eltm category fc2, on page 1193• event-history eltm category fc2, on page 1194
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1110
E Commands
Page 1255
• event-history eltm category mts, on page 1195• event-history eltm category mts, on page 1196• event-history epp category all, on page 1197• event-history epp category all, on page 1198• event-history epp category fc2, on page 1199• event-history epp category fc2, on page 1200• event-history epp category mts, on page 1201• event-history epp category mts, on page 1202• event-history errors, on page 1203• event-history ethpm, on page 1204• event-history events, on page 1205• event-history exceptionlog, on page 1206• event-history fcoe_mgr category all, on page 1208• event-history fcoe_mgr category all, on page 1209• event-history fcoe_mgr category fc2, on page 1210• event-history fcoe_mgr category fc2, on page 1211• event-history fcoe_mgr category mts, on page 1212• event-history fcoe_mgr category mts, on page 1213• event-history hardware-telemetry, on page 1214• event-history im category mts, on page 1215• event-history imp category all, on page 1216• event-history imp category all, on page 1217• event-history imp category fc2, on page 1218• event-history imp category fc2, on page 1219• event-history imp category mts, on page 1220• event-history imp category mts, on page 1221• event-history keystore, on page 1222• event-history lacp category all, on page 1223• event-history lacp category all, on page 1224• event-history lacp category fc2, on page 1225• event-history lacp category fc2, on page 1226• event-history lacp category mts, on page 1227• event-history lacp category mts, on page 1228• event-history lem-mgr category all, on page 1229• event-history lem-mgr category all, on page 1230• event-history lem-mgr category fc2, on page 1231• event-history lem-mgr category fc2, on page 1232• event-history lem-mgr category mts, on page 1233• event-history lem-mgr category mts, on page 1234• event-history license, on page 1235• event-history lldp category all, on page 1236• event-history lldp category all, on page 1237• event-history lldp category fc2, on page 1238• event-history lldp category fc2, on page 1239• event-history lldp category mts, on page 1240• event-history lldp category mts, on page 1241
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1111
E Commands
Page 1256
• event-history m2rib category all, on page 1242• event-history mfdm category all, on page 1243• event-history mfdm category all, on page 1244• event-history mfdm category fc2, on page 1245• event-history mfdm category fc2, on page 1246• event-history mfdm category mts, on page 1247• event-history mfdm category mts, on page 1248• event-history mmode category all, on page 1249• event-history module, on page 1250• event-history npv category all, on page 1251• event-history npv category all, on page 1252• event-history npv category fc2, on page 1253• event-history npv category fc2, on page 1254• event-history npv category mts, on page 1255• event-history npv category mts, on page 1256• event-history pfstat category all, on page 1257• event-history pfstat category all, on page 1258• event-history pfstat category fc2, on page 1259• event-history pfstat category fc2, on page 1260• event-history pfstat category mts, on page 1261• event-history pfstat category mts, on page 1262• event-history platform buffer-size, on page 1263• event-history platform category all, on page 1264• event-history platform category all, on page 1265• event-history pltfm_config category all, on page 1266• event-history pltfm_config category all, on page 1267• event-history pltfm_config category fc2, on page 1268• event-history pltfm_config category fc2, on page 1269• event-history pltfm_config category mts, on page 1270• event-history pltfm_config category mts, on page 1271• event-history plugin, on page 1272• event-history poap category all, on page 1273• event-history poap category all, on page 1274• event-history poap category fc2, on page 1275• event-history poap category fc2, on page 1276• event-history poap category mts, on page 1277• event-history poap category mts, on page 1278• event-history port-profile category all, on page 1279• event-history port-profile category mts, on page 1280• event-history port-resources category all, on page 1281• event-history port-resources category all, on page 1282• event-history port-resources category fc2, on page 1283• event-history port-resources category fc2, on page 1284• event-history port-resources category mts, on page 1285• event-history port-resources category mts, on page 1286• event-history port-security category all, on page 1287
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1112
E Commands
Page 1257
• event-history port-security category all, on page 1288• event-history port-security category fc2, on page 1289• event-history port-security category fc2, on page 1290• event-history port-security category mts, on page 1291• event-history port-security category mts, on page 1292• event-history port category fc2, on page 1293• event-history port category fc2, on page 1294• event-history port category mts, on page 1295• event-history port category mts, on page 1296• event-history port_client category all, on page 1297• event-history port_client category all, on page 1298• event-history port_client category fc2, on page 1299• event-history port_client category fc2, on page 1300• event-history port_client category mts, on page 1301• event-history port_client category mts, on page 1302• event-history san-port-channel category all, on page 1303• event-history san-port-channel category all, on page 1304• event-history san-port-channel category fc2, on page 1305• event-history san-port-channel category fc2, on page 1306• event-history san-port-channel category mts, on page 1307• event-history san-port-channel category mts, on page 1308• event-history sensor, on page 1309• event-history session-mgr category all, on page 1310• event-history session-mgr category all, on page 1311• event-history session-mgr category mts, on page 1312• event-history session-mgr category mts, on page 1313• event-history sflow, on page 1314• event-history snmp, on page 1315• event-history spanning-tree category all, on page 1316• event-history spm category all, on page 1317• event-history spm category all, on page 1318• event-history spm category fc2, on page 1319• event-history spm category fc2, on page 1320• event-history spm category mts, on page 1321• event-history spm category mts, on page 1322• event-history stripcl category all, on page 1323• event-history stripcl category all, on page 1324• event-history stripcl category mts, on page 1325• event-history tamnw category all, on page 1326• event-history tamnw category all, on page 1327• event-history tamnw category fc2, on page 1328• event-history tamnw category fc2, on page 1329• event-history tamnw category mts, on page 1330• event-history tamnw category mts, on page 1331• event-history udld category all, on page 1332• event-history ufdm category all, on page 1333
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1113
E Commands
Page 1258
• event-history ufdm category all, on page 1334• event-history ufdm category fc2, on page 1335• event-history ufdm category fc2, on page 1336• event-history ufdm category mts, on page 1337• event-history ufdm category mts, on page 1338• event-history vdc category all, on page 1339• event-history vdc category all, on page 1340• event-history vdc category mts, on page 1341• event-history xbar category all, on page 1342• event-history xbar category all, on page 1343• event-history xbar category debug, on page 1344• event-history xbar category debug, on page 1345• event-history xbar category mts, on page 1346• event-history xbar category mts, on page 1347• event-log-size, on page 1348• event-logging, on page 1349• event, on page 1350• event, on page 1351• event application sub-system type, on page 1352• event cli match, on page 1353• event counter name entry-val entry-op, on page 1354• event fanabsent time, on page 1355• event fanbad time, on page 1356• event fib adjacency extra, on page 1357• event fib resource tcam usage, on page 1358• event fib route, on page 1359• event gold module test testing-type scheduled consecutive-failure, on page 1360• event manager applet, on page 1361• event manager clear counter, on page 1362• event manager clear history events, on page 1363• event manager environment, on page 1364• event manager policy, on page 1365• event manager run, on page 1366• event memory, on page 1367• event module-failure type module count, on page 1368• event module status module1, on page 1369• event neighbor-discovery, on page 1370• event none, on page 1371• event oir fan, on page 1372• event oir module, on page 1373• event oir powersupply, on page 1374• event policy-default count, on page 1375• event poweroverbudget, on page 1376• event snmp oid get-type exact entry-op entry-val poll-interval, on page 1377• event storm-control, on page 1379• event syslog pattern, on page 1380
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1114
E Commands
Page 1259
• event sysmgr memory major minor clear, on page 1381• event sysmgr switchover count time, on page 1382• event temperature threshold, on page 1383• event test match, on page 1384• event timer, on page 1385• event track state, on page 1386• evpn, on page 1387• evpn esi multihoming, on page 1388• evpn multihoming core-tracking, on page 1389• evpn multisite border-gateway, on page 1390• evpn multisite dci-tracking, on page 1391• evpn multisite fabric-tracking, on page 1392• evpn storm-control level, on page 1393• exceptionlog module syserr devid errtype errcode phylayer ports harderror, on page 1394• exclude access-list, on page 1395• exclude access-list, on page 1396• exec-timeout, on page 1397• exec-timeout, on page 1398• existing-cli, on page 1399• exit, on page 1400• exit, on page 1401• exp, on page 1402• explicit-null, on page 1403• explicit-path, on page 1404• explicit-path identifier, on page 1405• export-gateway-ip, on page 1406• export map, on page 1407• export vrf default map, on page 1408• exporter-id, on page 1409• exporter, on page 1410• exporter, on page 1411• exporter, on page 1412• exporter, on page 1413• exporter, on page 1414
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1115
E Commands
Page 1260
eapol mac-address[no] eapol mac-address { <mac_addr> | broadcast-address } [ ethertype <eth_type> ]
Syntax Description
specify mac address and ether type for eapol packetseapol
mac addressmac-address
mac address destination specified as a stringmac_addr
broadcast addressbroadcast-address
(Optional) ether typeethertype
(Optional) ether type specified as stringeth_type
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-ethernet-p2p /exec/configure/if-eth-non-member/exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1116
E Commandseapol mac-address
Page 1261
ebgp-multihopebgp-multihop <ebgp-ttl> | { no | default } ebgp-multihop [ <ebgp-ttl> ]
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Specify multihop TTL for remote peerebgp-multihop
EBGP TTL valueebgp-ttl
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1117
E Commandsebgp-multihop
Page 1262
echoecho [ -e ] [ <line> ]
Syntax Description
echo argument back to screen (useful for scripts)echo
(Optional) enable interpretation of the backslash-escaped characters-e
(Optional) the string to echo (use quotes if string contains spaces)line
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1118
E Commandsecho
Page 1263
echoecho { { revision { 3 | 4 } } | { vendor-extension } } | no echo { { revision } | { vendor-extension } }
Syntax Description
Negate a command or set its defaultsno
Echo Request attributesecho
Echo packet default revisionrevision
draft-ietf-mpls-lsp-ping-03 (rev 2)3
RFC 4379 Compliant4
Send Vendor Extension TLV with echo Reqvendor-extension
Command Mode
• /exec/configure/mpls-oam
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1119
E Commandsecho
Page 1264
ecp max-retriesecp max-retries <cnt> | no ecp max-retries [ <cnt> ]
Syntax Description
Negate a command or set its defaultsno
ECP (Edge Control Protocol)ecp
Maximal number of retransmissionsmax-retries
Numer of retries. default 3cnt
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1120
E Commandsecp max-retries
Page 1265
ecp mode lan[no] ecp mode lan
Syntax Description
(Optional) Negate a command or set its defaultsno
ECP (Edge Control Protocol)ecp
ECP session modemode
Enable ECP LAN modelan
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1121
E Commandsecp mode lan
Page 1266
ecp retransmission-timer-exponentecp retransmission-timer-exponent <exp> | no ecp retransmission-timer-exponent [ <exp> ]
Syntax Description
Negate a command or set its defaultsno
ECP (Edge Control Protocol)ecp
Retransmission timer exponentretransmission-timer-exponent
Timer exponent. default: 14 (ex. 10 exp ~ 10 ms)exp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1122
E Commandsecp retransmission-timer-exponent
Page 1267
eem testeem test <param>
Syntax Description
Event Manager commandeem
Do test actiontest
Test action parameter (dummy value)param
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1123
E Commandseem test
Page 1268
eemtest policy-addeemtest policy-add <name> [ override <override-name> ]
Syntax Description
EEM test commandseemtest
Add a client policypolicy-add
Name of policy (cannot have underscore in first two characters)name
(Optional) Override a system policyoverride
(Optional) Name of the system policy to override - should begin withdouble underscore
override-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1124
E Commandseemtest policy-add
Page 1269
eemtest policy-removeeemtest policy-remove <name> [ override <override-name> ]
Syntax Description
EEM test commandseemtest
Remove a client policypolicy-remove
Name of policy (cannot have underscore in first two characters)name
(Optional) Override a system policyoverride
(Optional) Name of the system policy to override - should begin withdouble underscore
override-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1125
E Commandseemtest policy-remove
Page 1270
egress-engineering[ no | default ] egress-engineering [ peer-set <peer-set-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure Egress Peer Engineering (EPE) for peeregress-engineering
(Optional) Configure EPE Peer-Setpeer-set
(Optional) EPE Peer-Set namepeer-set-name
Command Mode
• /exec/configure/router-bgp/router-bgp-template-neighbor/exec/configure/router-bgp/router-bgp-neighbor-stmp /exec/configure/router-bgp/router-bgp-neighbor/exec/configure/router-bgp/router-bgp-prefixneighbor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1126
E Commandsegress-engineering
Page 1271
egress{ egress <eid> | no egress }
Syntax Description
Negate a command or set its defaultsno
Outgoing egress Interfaceegress
Outgoing egress Interface identifiereid
Command Mode
• /exec/configure/configngoamconnectcheck
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1127
E Commandsegress
Page 1272
eid-prefix{ [ no ] eid-prefix { <eid-prefix> | <eid-prefix6> } [ instance-id <iid> ] [ route-tag <tag> ] [accept-more-specifics ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
EID-prefix for LISP siteeid-prefix
IP EID-prefix of the siteeid-prefix
(Optional) Configures instance-ID for site's EID-prefixinstance-id
(Optional) 24-bit instance-ID valueiid
(Optional) Route tag for LISP EID-prefix routesroute-tag
(Optional) 32-bit value for tagtag
(Optional) Allow more-specifics of site EID-prefix to registeraccept-more-specifics
Command Mode
• /exec/configure/lisp-site /exec/configure/vrf/lisp-site
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1128
E Commandseid-prefix
Page 1273
eigrp event-history cli size[no] eigrp [ <eigrp-ptag> ] event-history { cli } size { <size_in_text> | <size_in_Kbytes> }
Syntax Description
(Optional) Negate a command or set its defaultsno
EIGRP clear commandseigrp
(Optional) Process tageigrp-ptag
Event History of EIGRPevent-history
EIGRP CLI related eventscli
Configure the size of the event-hist buffersize
Buffer sizesize_in_text
Size of the file in kbytessize_in_Kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1129
E Commandseigrp event-history cli size
Page 1274
eigrp file-debug[no] eigrp file-debug
Syntax Description
(Optional) Negate a command or set its defaultsno
EIGRPeigrp
Collect all debugs to a filefile-debug
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1130
E Commandseigrp file-debug
Page 1275
email-addr[no] email-addr <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Add email addr to send output of jobs configured for this scheduleemail-addr
Provide email address, example: [email protected]
Command Mode
• /exec/configure/schedule
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1131
E Commandsemail-addr
Page 1276
email-contact{ email-contact <s0> | no email-contact }
Syntax Description
Negate a command or set its defaultsno
email address of the contact personemail-contact
Provide email address, example: [email protected]
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1132
E Commandsemail-contact
Page 1277
email[no] email
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure pipe emailemail
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1133
E Commandsemail
Page 1278
email| email [ -f <fromemail> | -r <replytoemail> | -S <smtphost> | -P <smtpport> | -s <subject> | -c<vrf-known-name> ] + <toemail>
Syntax Description
Pipe command output to filter|
Email command outputemail
(Optional) From address-f
(Optional) Email addressfromemail
(Optional) Reply to address-r
(Optional) Email addressreplytoemail
(Optional) SMTP host-S
(Optional) IPV4/IPV6 address or DNS namesmtphost
(Optional) SMTP port-P
(Optional) SMTP port numbersmtpport
(Optional) Subject-s
(Optional) Email subjectsubject
(Optional) VRF-c
(Optional) VRF namevrf-known-name
Recipient email addresstoemail
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1134
E Commandsemail
Page 1279
enableenable [ <enable-level> ]
Syntax Description
Turn on privileged commandsenable
(Optional) Enable Levelenable-level
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1135
E Commandsenable
Page 1280
enable[no] enable
Syntax Description
(Optional) Negate a command or set its defaultsno
enable callhomeenable
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1136
E Commandsenable
Page 1281
enable Cert[no] enable { Cert-DN-match | user-server-group }
Syntax Description
(Optional) Negate a command or set its defaultsno
Enableenable
Enable/Disable group validationuser-server-group
Enable/Disable Cert-DN matchingCert-DN-match
Command Mode
• /exec/configure/ldap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1137
E Commandsenable Cert
Page 1282
encapsulation dot1qencapsulation dot1q <vlan_id> | no encapsulation dot1q [ <vlan_id> ]
Syntax Description
Negate a command or set its defaultsno
Set encapsulation type for an interfaceencapsulation
IEEE 802.1Q Virtual LANdot1q
IEEE 802.1Q VLAN ID requiredvlan_id
Command Mode
• /exec/configure/if-gig-ether-sub /exec/configure/if-remote-ethernet-sub
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1138
E Commandsencapsulation dot1q
Page 1283
encapsulation dot1qencapsulation dot1q <vlan_id> | no encapsulation dot1q [ <vlan_id> ]
Syntax Description
Negate a command or set its defaultsno
Set encapsulation type for an interfaceencapsulation
IEEE 802.1Q Virtual LANdot1q
IEEE 802.1Q VLAN ID requiredvlan_id
Command Mode
• /exec/configure/if-ether-sub /exec/configure/if-port-channel-sub /exec/configure/if-ether-sub-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1139
E Commandsencapsulation dot1q
Page 1284
encrypt pause-frame[no] encrypt pause-frame
Syntax Description
Enable/disable encryption for specific type of framesencrypt
Ethernet PAUSE framespause-frame
Command Mode
• /exec/configure/cts-dot1x /exec/configure/cts-manual
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1140
E Commandsencrypt pause-frame
Page 1285
encryption decrypt type6encryption decrypt type6
Syntax Description
Strong encryption for credential(s)encryption
Decrypts strongly encrypted secret(s) to obfuscated type(s)decrypt
type6 secrets present in systemtype6
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1141
E Commandsencryption decrypt type6
Page 1286
encryption delete type6encryption delete type6 [ <uuid> | <name> ]
Syntax Description
Strong encryption for credential(s)encryption
Deletes strongly encrypted secret(s)delete
type6 secrets present in systemtype6
(Optional) uuid of the appuuid
(Optional) Service namename
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1142
E Commandsencryption delete type6
Page 1287
encryption re-encrypt obfuscatedencryption re-encrypt obfuscated
Syntax Description
Strong encryption for credential(s)encryption
Re-encrypts weekly encrypted secret(s) to strongly encrypted secret(s)re-encrypt
type-3/type-7/clear-text secrets present in systemobfuscated
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1143
E Commandsencryption re-encrypt obfuscated
Page 1288
endend
Syntax Description
Go to exec modeend
Command Mode
• /global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1144
E Commandsend
Page 1289
endpoint{ no endpoint | endpoint <pfx> }
Syntax Description
Negate a command or set its defaultsno
Policy Endpointendpoint
IPv4 endpoint addresspfx
Command Mode
• /exec/configure/sr/te/pol
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1145
E Commandsendpoint
Page 1290
enforce-first-as[no] enforce-first-as
Syntax Description
(Optional) Negate a command or set its defaultsno
Enforce neighbor AS is the first AS in AS-PATH attribute (EBGP)enforce-first-as
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1146
E Commandsenforce-first-as
Page 1291
enrollment terminal[no] enrollment terminal
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure trustpoint enrollmentenrollment
Configure trustpoint enrollment via consoleterminal
Command Mode
• /exec/configure/trustpoint
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1147
E Commandsenrollment terminal
Page 1292
errdisableerrdisable { detect cause_detect { all_cause | link-flap_cause | loopback_cause } | recovery { cause_recovery{ all_recovery | udld | loopback_recovery | bpduguard | security-violation | psecure-violation | link-flap-recovery| storm-control | dcbx-no-ack | vpc-peerlink | failed-port-state } } } | no errdisable { detect cause_detect {all_cause | link-flap_cause | loopback_cause } | recovery { cause_recovery { all_recovery | udld |loopback_recovery | bpduguard | security-violation | psecure-violation | link-flap-recovery | storm-control |dcbx-no-ack | vpc-peerlink | failed-port-state } } }
Syntax Description
Negate a command or set its defaultsno
Error disableerrdisable
Error disable detectiondetect
Enable error disable detection for applicationcause_detect
Enable error detection on all casesall_cause
Enable error disable detection on linkstate-flappinglink-flap_cause
Enable error disable detection on loopback detected by UDLDloopback_cause
Error disable recoveryrecovery
Enable error disable recovery for applicationcause_recovery
Enable timer to recover from all causesall_recovery
Enable timer to recover from udld error disabled stateudld
Enable timer to recover from loopback error disabled state detected byUDLD
loopback_recovery
Enable timer to recover from BPDU Guard error disable statebpduguard
Enable timer to recover from 802.1x violation disable statesecurity-violation
Enable timer to recover from psecure violation disable statepsecure-violation
Enable timer to recover from linkstate flappinglink-flap-recovery
Enable timer to recover from storm control error disabled statestorm-control
Enable timer to recover from no DCBX Acksdcbx-no-ack
Enable timer to recover from inconsistent vpc peer-linkvpc-peerlink
Enable timer to recover from stp set port state failurefailed-port-state
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1148
E Commandserrdisable
Page 1293
errdisable detect cause[no] errdisable detect cause { link-down [ num-times <i0> duration <i1> ] | trustsec-violation [ num-times<i0> duration <i1> ] | bit-errors [ num-times <i0> duration <i1> ] | signal-loss [ num-times <i0> duration<i1> ] | sync-loss [ num-times <i0> duration <i1> ] | link-reset [ num-times <i0> duration <i1> ] | credit-loss[ num-times <i0> duration <i1> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Error Disable the porterrdisable
Enter detect reasondetect
Enter port down causecause
Detection of excessive link down eventslink-down
Detection of excessive trustsec violation eventstrustsec-violation
Detection of excessive bit error eventsbit-errors
Detection of excessive signal loss eventssignal-loss
Detection of excessive sync loss eventssync-loss
Detection of excessive link reset eventslink-reset
Detection of excessive credit loss eventscredit-loss
(Optional) Enter number of flapsnum-times
(Optional) Enter number of flapsi0
(Optional) Enter duration in secondsduration
(Optional) Enter duration in secondsi1
Command Mode
• /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1149
E Commandserrdisable detect cause
Page 1294
errdisable detect cause acl-exception[no] errdisable detect cause acl-exception
Syntax Description
(Optional) Negate a command or set its defaultsno
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1150
E Commandserrdisable detect cause acl-exception
Page 1295
errdisable port detect cause acl-exception[no] errdisable port detect cause acl-exception
Syntax Description
(Optional) Negate a command or set its defaultsno
Command Mode
• /exec/configure/if-ethernet /exec/configure/if-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1151
E Commandserrdisable port detect cause acl-exception
Page 1296
errdisable recovery intervalerrdisable recovery interval <val> | no errdisable recovery interval [ <val> ]
Syntax Description
Negate a command or set its defaultsno
Error disableerrdisable
Error disable recoveryrecovery
Error disable recovery timer valueinterval
timer-interval (sec)val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1152
E Commandserrdisable recovery interval
Page 1297
erspan-id[no] erspan-id <flow_id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Erspan ID for ERSPAN sessionserspan-id
erspan-idflow_id
Command Mode
• /exec/configure/monitor-erspan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1153
E Commandserspan-id
Page 1298
ethanalyzer local[no] ethanalyzer local [ { { {
Syntax Description
(Optional) inband{
(Optional) Negate a command or set its defaultsno
Configure cisco packet analyzerethanalyzer
start local capture of frames to Suplocal
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1154
E Commandsethanalyzer local
Page 1299
ethernet-segment[no] ethernet-segment <es-num>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Ethernet-Segmentethernet-segment
ethernet-segment numberes-num
Command Mode
• /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1155
E Commandsethernet-segment
Page 1300
ethernet-segment delay-restore time[no] ethernet-segment delay-restore time <sec>
Syntax Description
(Optional) Negate a command or set its defaultsno
ethernet-segmentethernet-segment
delay-restoredelay-restore
timetime
time in secondssec
Command Mode
• /exec/configure/evpn-esi-mh
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1156
E Commandsethernet-segment delay-restore time
Page 1301
ethernet-tag encapsulation dot1q default static{ ethernet-tag encapsulation dot1q default { static <profile-name> | dynamic } } | { no ethernet-tag encapsulationdot1q default }
Syntax Description
Negate a command or set its defaultsno
Data snooping triggersethernet-tag
Encapsulation/Trigger typeencapsulation
Static Profile Map: Configure profile name via CLIstatic
Static Profile Map: Configure profile name via CLIprofile-name
Dynamic Profile Map: Retrieve profile name from the external serverdynamic
Dot1Q Encapsulationdot1q
Default (wildcard). Match any dot1q when there is no specific dot1qmapping configured
default
Command Mode
• /exec/configure/profile-map /exec/configure/profile-map-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1157
E Commandsethernet-tag encapsulation dot1q default static
Page 1302
ethernet-tag encapsulation dot1q static{ ethernet-tag encapsulation dot1q <vlan-id> { static <profile-name> | dynamic } } | { no ethernet-tagencapsulation dot1q <vlan-id> }
Syntax Description
Negate a command or set its defaultsno
Data snooping triggersethernet-tag
Encapsulation/Trigger typeencapsulation
Static Profile Map: Configure profile name via CLIstatic
Static Profile Map: Configure profile name via CLIprofile-name
Dynamic Profile Map: Retrieve profile name from the external serverdynamic
Dot1Q Encapsulationdot1q
vlan-id
Command Mode
• /exec/configure/profile-map /exec/configure/profile-map-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1158
E Commandsethernet-tag encapsulation dot1q static
Page 1303
ethernet-tag encapsulation vni default static{ ethernet-tag encapsulation vni default { static <profile-name> | dynamic } } | { no ethernet-tag encapsulationvni default }
Syntax Description
Negate a command or set its defaultsno
Data snooping triggersethernet-tag
Encapsulation/Trigger typeencapsulation
Static Profile Map: Configure profile name via CLIstatic
Static Profile Map: Configure profile name via CLIprofile-name
Dynamic Profile Map: Retrieve profile name from the external serverdynamic
Virtual Network Identifiervni
Default (wildcard). Match any vni when there is no specific vni mappingconfigured
default
Command Mode
• /exec/configure/profile-map /exec/configure/profile-map-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1159
E Commandsethernet-tag encapsulation vni default static
Page 1304
ethernet-tag encapsulation vni static{ ethernet-tag encapsulation vni <vni-id> { static <profile-name> | dynamic } } | { no ethernet-tag encapsulationvni <vni-id> }
Syntax Description
Negate a command or set its defaultsno
Data snooping triggersethernet-tag
Encapsulation/Trigger typeencapsulation
Static Profile Map: Configure profile name via CLIstatic
Static Profile Map: Configure profile name via CLIprofile-name
Dynamic Profile Map: Retrieve profile name from the external serverdynamic
Virtual Network Identifiervni
vni-id
Command Mode
• /exec/configure/profile-map /exec/configure/profile-map-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1160
E Commandsethernet-tag encapsulation vni static
Page 1305
evb mac{ evb mac <mac-addr> } | { no evb mac [ <mac-addr> ] }
Syntax Description
Negate a command or set its defaultsno
EVB (Edge Virtual Bridge)evb
VDP multicast MAC addressmac
MAC Addressmac-addr
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1161
E Commandsevb mac
Page 1306
evb reinit-keep-alive{ evb reinit-keep-alive <exp> } | { no evb reinit-keep-alive [ <exp> ] }
Syntax Description
Negate a command or set its defaultsno
EVB (Edge Virtual Bridge)evb
Keepalivereinit-keep-alive
Timer exponent. (Min 22 exp ~ 40 seconds)exp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1162
E Commandsevb reinit-keep-alive
Page 1307
evb resource-wait-delay{ evb resource-wait-delay <exp> } | { no evb resource-wait-delay [ <exp> ] }
Syntax Description
Negate a command or set its defaultsno
EVB (Edge Virtual Bridge)evb
Resource wait delayresource-wait-delay
Timer exponent. (Min 22 exp ~ 40 seconds)exp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1163
E Commandsevb resource-wait-delay
Page 1308
event-history[no] event-history { detail | periodic | objstore } [ size { <size_in_text> | <bytes> | disable } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure event-history detailsevent-history
Detailed event history bufferdetail
Periodic events history bufferperiodic
Objstore events history bufferobjstore
(Optional) Set the buffer sizesize
(Optional) Disable the bufferdisable
(Optional) Buffer sizesize_in_text
(Optional) Buffer size in bytesbytes
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1164
E Commandsevent-history
Page 1309
event-history acllog category allevent-history acllog category all
Syntax Description
switch wide event history configurationevent-history
Configure acllog event logsacllog
Configure acllog event logs for categorycategory
Configure acllog event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1165
E Commandsevent-history acllog category all
Page 1310
event-history acllog category allevent-history acllog no category all
Syntax Description
switch wide event history configurationevent-history
Configure acllog event logsacllog
Disable acllog event logs for categoryno
Configure acllog event logs for categorycategory
Configure acllog event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1166
E Commandsevent-history acllog category all
Page 1311
event-history acllog category fc2event-history acllog category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure acllog event logsacllog
Configure acllog event logs for categorycategory
Configure acllog event logs for category FC2fc2
(Optional) Configure acllog event logs for FC2 Rx framesrx
(Optional) Configure brief acllog event logs for FC2 Rxbrief
(Optional) Configure detail acllog event logs for FC2 Rxdetail
(Optional) Configure acllog event logs for FC2 Tx framestx
(Optional) Configure brief acllog event logs for FC2 Txbrief1
(Optional) Configure detail acllog event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1167
E Commandsevent-history acllog category fc2
Page 1312
event-history acllog category fc2event-history acllog no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure acllog event logsacllog
Disable acllog event logs for categoryno
Configure acllog event logs for categorycategory
Configure acllog event logs for category FC2fc2
(Optional) Configure acllog event logs for FC2 Rx framesrx
(Optional) Configure brief acllog event logs for FC2 Rxbrief
(Optional) Configure detail acllog event logs for FC2 Rxdetail
(Optional) Configure acllog event logs for FC2 Tx framestx
(Optional) Configure brief acllog event logs for FC2 Txbrief1
(Optional) Configure detail acllog event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1168
E Commandsevent-history acllog category fc2
Page 1313
event-history acllog category mtsevent-history acllog category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure acllog event logsacllog
Configure acllog event logs for categorycategory
Configure acllog event logs for category mtsmts
(Optional) Configure acllog event logs for mts Rx framesrx
(Optional) Configure brief acllog event logs for mts Rxbrief
(Optional) Configure detail acllog event logs for mts Rxdetail
(Optional) Configure acllog event logs for mts Tx framestx
(Optional) Configure brief acllog event logs for mts Txbrief1
(Optional) Configure detail acllog event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1169
E Commandsevent-history acllog category mts
Page 1314
event-history acllog category mtsevent-history acllog no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure acllog event logsacllog
Disable acllog event logs for categoryno
Configure acllog event logs for categorycategory
Configure acllog event logs for category mtsmts
(Optional) Configure acllog event logs for mts Rx framesrx
(Optional) Configure brief acllog event logs for mts Rxbrief
(Optional) Configure detail acllog event logs for mts Rxdetail
(Optional) Configure acllog event logs for mts Tx framestx
(Optional) Configure brief acllog event logs for mts Txbrief1
(Optional) Configure detail acllog event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1170
E Commandsevent-history acllog category mts
Page 1315
event-history adbm category allevent-history adbm no category all
Syntax Description
switch wide event history configurationevent-history
Configure adbm event logsadbm
Disable adbm event logs for categoryno
Configure adbm event logs for categorycategory
Configure adbm event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1171
E Commandsevent-history adbm category all
Page 1316
event-history adbm category allevent-history adbm category all
Syntax Description
switch wide event history configurationevent-history
Configure adbm event logsadbm
Configure adbm event logs for categorycategory
Configure adbm event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1172
E Commandsevent-history adbm category all
Page 1317
event-history adbm category fc2event-history adbm category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure adbm event logsadbm
Configure adbm event logs for categorycategory
Configure adbm event logs for category FC2fc2
(Optional) Configure adbm event logs for FC2 Rx framesrx
(Optional) Configure brief adbm event logs for FC2 Rxbrief
(Optional) Configure detail adbm event logs for FC2 Rxdetail
(Optional) Configure adbm event logs for FC2 Tx framestx
(Optional) Configure brief adbm event logs for FC2 Txbrief1
(Optional) Configure detail adbm event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1173
E Commandsevent-history adbm category fc2
Page 1318
event-history adbm category fc2event-history adbm no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure adbm event logsadbm
Disable adbm event logs for categoryno
Configure adbm event logs for categorycategory
Configure adbm event logs for category FC2fc2
(Optional) Configure adbm event logs for FC2 Rx framesrx
(Optional) Configure brief adbm event logs for FC2 Rxbrief
(Optional) Configure detail adbm event logs for FC2 Rxdetail
(Optional) Configure adbm event logs for FC2 Tx framestx
(Optional) Configure brief adbm event logs for FC2 Txbrief1
(Optional) Configure detail adbm event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1174
E Commandsevent-history adbm category fc2
Page 1319
event-history adbm category mtsevent-history adbm category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure adbm event logsadbm
Configure adbm event logs for categorycategory
Configure adbm event logs for category mtsmts
(Optional) Configure adbm event logs for mts Rx framesrx
(Optional) Configure brief adbm event logs for mts Rxbrief
(Optional) Configure detail adbm event logs for mts Rxdetail
(Optional) Configure adbm event logs for mts Tx framestx
(Optional) Configure brief adbm event logs for mts Txbrief1
(Optional) Configure detail adbm event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1175
E Commandsevent-history adbm category mts
Page 1320
event-history adbm category mtsevent-history adbm no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure adbm event logsadbm
Disable adbm event logs for categoryno
Configure adbm event logs for categorycategory
Configure adbm event logs for category mtsmts
(Optional) Configure adbm event logs for mts Rx framesrx
(Optional) Configure brief adbm event logs for mts Rxbrief
(Optional) Configure detail adbm event logs for mts Rxdetail
(Optional) Configure adbm event logs for mts Tx framestx
(Optional) Configure brief adbm event logs for mts Txbrief1
(Optional) Configure detail adbm event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1176
E Commandsevent-history adbm category mts
Page 1321
event-history callhomeevent-history callhome { mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ] | no mts [ { rx [ { brief1| detail1 } ] | tx [ { brief2 | detail2 } ] } ] }
Syntax Description
switch wide event history configurationevent-history
Configure Callhome event logscallhome
Configure callhome event logs for MTSmts
(Optional) Configure callhome event logs for MTS Rx framesrx
(Optional) Configure brief callhome event logs for MTS Rxbrief
(Optional) Configure detail callhome event logs for MTS Rxdetail
(Optional) Configure callhome event logs for MTS Tx framestx
(Optional) Configure brief callhome event logs for MTS Txbrief1
(Optional) Configure detail callhome event logs for MTS Txdetail1
Disable callhome event logs for MTSno
Configure callhome event logs for MTSmts
(Optional) Configure callhome event logs for MTS Rx framesrx
(Optional) Configure brief callhome event logs for MTS Rxbrief1
(Optional) Configure detail callhome event logs for MTS Rxdetail1
(Optional) Configure callhome event logs for MTS Tx framestx
(Optional) Configure brief callhome event logs for MTS Txbrief2
(Optional) Configure detail callhome event logs for MTS Txdetail2
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1177
E Commandsevent-history callhome
Page 1322
event-history capabilityevent-history capability { category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ] } | nocategory { all | mts [ { rx [ { brief1 | detail1 } ] | tx [ { brief2 | detail2 } ] } ] } }
Syntax Description
switch wide event history configurationevent-history
Configure capability event logscapability
Configure capability event logs for categorycategory
Configure capability event logs for category all eventsall
Configure capability event logs for category mtsmts
(Optional) Configure capability event logs for mts Rx framesrx
(Optional) Configure brief capability event logs for mts Rxbrief
(Optional) Configure detail capability event logs for mts Rxdetail
(Optional) Configure capability event logs for mts Tx framestx
(Optional) Configure brief capability event logs for mts Txbrief1
(Optional) Configure detail capability event logs for mts Txdetail1
Disable capability event logs for categoryno
Configure capability event logs for categorycategory
Configure capability event logs for category all eventsall
Configure capability event logs for category mtsmts
(Optional) Configure capability event logs for mts Rx framesrx
(Optional) Configure brief capability event logs for mts Rxbrief1
(Optional) Configure detail capability event logs for mts Rxdetail1
(Optional) Configure capability event logs for mts Tx framestx
(Optional) Configure brief capability event logs for mts Txbrief2
(Optional) Configure detail capability event logs for mts Txdetail2
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1178
E Commandsevent-history capability
Page 1323
event-history cli[no] event-history cli [ size { <size_in_text> | <bytes> | disable } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure event-history detailsevent-history
CLI event history buffercli
(Optional) Set the buffer sizesize
(Optional) Disable the bufferdisable
(Optional) Buffer sizesize_in_text
(Optional) Buffer size in bytesbytes
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1179
E Commandsevent-history cli
Page 1324
event-history copp category allevent-history copp category all
Syntax Description
switch wide event history configurationevent-history
Configure copp event logscopp
Configure copp event logs for categorycategory
Configure copp event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1180
E Commandsevent-history copp category all
Page 1325
event-history copp category allevent-history copp no category all
Syntax Description
switch wide event history configurationevent-history
Configure copp event logscopp
Disable copp event logs for categoryno
Configure copp event logs for categorycategory
Configure copp event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1181
E Commandsevent-history copp category all
Page 1326
event-history copp category fc2event-history copp category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure copp event logscopp
Configure copp event logs for categorycategory
Configure copp event logs for category FC2fc2
(Optional) Configure copp event logs for FC2 Rx framesrx
(Optional) Configure brief copp event logs for FC2 Rxbrief
(Optional) Configure detail copp event logs for FC2 Rxdetail
(Optional) Configure copp event logs for FC2 Tx framestx
(Optional) Configure brief copp event logs for FC2 Txbrief1
(Optional) Configure detail copp event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1182
E Commandsevent-history copp category fc2
Page 1327
event-history copp category fc2event-history copp no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure copp event logscopp
Disable copp event logs for categoryno
Configure copp event logs for categorycategory
Configure copp event logs for category FC2fc2
(Optional) Configure copp event logs for FC2 Rx framesrx
(Optional) Configure brief copp event logs for FC2 Rxbrief
(Optional) Configure detail copp event logs for FC2 Rxdetail
(Optional) Configure copp event logs for FC2 Tx framestx
(Optional) Configure brief copp event logs for FC2 Txbrief1
(Optional) Configure detail copp event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1183
E Commandsevent-history copp category fc2
Page 1328
event-history copp category mtsevent-history copp category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure copp event logscopp
Configure copp event logs for categorycategory
Configure copp event logs for category mtsmts
(Optional) Configure copp event logs for mts Rx framesrx
(Optional) Configure brief copp event logs for mts Rxbrief
(Optional) Configure detail copp event logs for mts Rxdetail
(Optional) Configure copp event logs for mts Tx framestx
(Optional) Configure brief copp event logs for mts Txbrief1
(Optional) Configure detail copp event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1184
E Commandsevent-history copp category mts
Page 1329
event-history copp category mtsevent-history copp no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure copp event logscopp
Disable copp event logs for categoryno
Configure copp event logs for categorycategory
Configure copp event logs for category mtsmts
(Optional) Configure copp event logs for mts Rx framesrx
(Optional) Configure brief copp event logs for mts Rxbrief
(Optional) Configure detail copp event logs for mts Rxdetail
(Optional) Configure copp event logs for mts Tx framestx
(Optional) Configure brief copp event logs for mts Txbrief1
(Optional) Configure detail copp event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1185
E Commandsevent-history copp category mts
Page 1330
event-history dot1xevent-history dot1x { category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ] } | no category{ all | mts [ { rx [ { brief1 | detail1 } ] | tx [ { brief2 | detail2 } ] } ] } }
Syntax Description
switch wide event history configurationevent-history
Configure dot1x event logsdot1x
Configure dot1x event logs for categorycategory
Configure dot1x event logs for category all eventsall
Configure dot1x event logs for category mtsmts
(Optional) Configure dot1x event logs for mts Rx framesrx
(Optional) Configure brief dot1x event logs for mts Rxbrief
(Optional) Configure detail dot1x event logs for mts Rxdetail
(Optional) Configure dot1x event logs for mts Tx framestx
(Optional) Configure brief dot1x event logs for mts Txbrief1
(Optional) Configure detail dot1x event logs for mts Txdetail1
Disable dot1x event logs for categoryno
Configure dot1x event logs for categorycategory
Configure dot1x event logs for category all eventsall
Configure dot1x event logs for category mtsmts
(Optional) Configure dot1x event logs for mts Rx framesrx
(Optional) Configure brief dot1x event logs for mts Rxbrief1
(Optional) Configure detail dot1x event logs for mts Rxdetail1
(Optional) Configure dot1x event logs for mts Tx framestx
(Optional) Configure brief dot1x event logs for mts Txbrief2
(Optional) Configure detail dot1x event logs for mts Txdetail2
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1186
E Commandsevent-history dot1x
Page 1331
event-history drap category allevent-history drap no category all
Syntax Description
switch wide event history configurationevent-history
Configure drap event logsdrap
Disable drap event logs for categoryno
Configure drap event logs for categorycategory
Configure drap event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1187
E Commandsevent-history drap category all
Page 1332
event-history drap category allevent-history drap category all
Syntax Description
switch wide event history configurationevent-history
Configure drap event logsdrap
Configure drap event logs for categorycategory
Configure drap event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1188
E Commandsevent-history drap category all
Page 1333
event-history drap category mtsevent-history drap no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure drap event logsdrap
Disable drap event logs for categoryno
Configure drap event logs for categorycategory
Configure drap event logs for category mtsmts
(Optional) Configure drap event logs for mts Rx framesrx
(Optional) Configure brief drap event logs for mts Rxbrief
(Optional) Configure detail drap event logs for mts Rxdetail
(Optional) Configure drap event logs for mts Tx framestx
(Optional) Configure brief drap event logs for mts Txbrief1
(Optional) Configure detail drap event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1189
E Commandsevent-history drap category mts
Page 1334
event-history drap category mtsevent-history drap category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure drap event logsdrap
Configure drap event logs for categorycategory
Configure drap event logs for category mtsmts
(Optional) Configure drap event logs for mts Rx framesrx
(Optional) Configure brief drap event logs for mts Rxbrief
(Optional) Configure detail drap event logs for mts Rxdetail
(Optional) Configure drap event logs for mts Tx framestx
(Optional) Configure brief drap event logs for mts Txbrief1
(Optional) Configure detail drap event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1190
E Commandsevent-history drap category mts
Page 1335
event-history eltm category allevent-history eltm no category all
Syntax Description
switch wide event history configurationevent-history
Configure eltm event logseltm
Disable eltm event logs for categoryno
Configure eltm event logs for categorycategory
Configure eltm event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1191
E Commandsevent-history eltm category all
Page 1336
event-history eltm category allevent-history eltm category all
Syntax Description
switch wide event history configurationevent-history
Configure eltm event logseltm
Configure eltm event logs for categorycategory
Configure eltm event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1192
E Commandsevent-history eltm category all
Page 1337
event-history eltm category fc2event-history eltm no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure eltm event logseltm
Disable eltm event logs for categoryno
Configure eltm event logs for categorycategory
Configure eltm event logs for category FC2fc2
(Optional) Configure eltm event logs for FC2 Rx framesrx
(Optional) Configure brief eltm event logs for FC2 Rxbrief
(Optional) Configure detail eltm event logs for FC2 Rxdetail
(Optional) Configure eltm event logs for FC2 Tx framestx
(Optional) Configure brief eltm event logs for FC2 Txbrief
(Optional) Configure detail eltm event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1193
E Commandsevent-history eltm category fc2
Page 1338
event-history eltm category fc2event-history eltm category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure eltm event logseltm
Configure eltm event logs for categorycategory
Configure eltm event logs for category FC2fc2
(Optional) Configure eltm event logs for FC2 Rx framesrx
(Optional) Configure brief eltm event logs for FC2 Rxbrief
(Optional) Configure detail eltm event logs for FC2 Rxdetail
(Optional) Configure eltm event logs for FC2 Tx framestx
(Optional) Configure brief eltm event logs for FC2 Txbrief
(Optional) Configure detail eltm event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1194
E Commandsevent-history eltm category fc2
Page 1339
event-history eltm category mtsevent-history eltm category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure eltm event logseltm
Configure eltm event logs for categorycategory
Configure eltm event logs for category mtsmts
(Optional) Configure eltm event logs for mts Rx framesrx
(Optional) Configure brief eltm event logs for mts Rxbrief
(Optional) Configure detail eltm event logs for mts Rxdetail
(Optional) Configure eltm event logs for mts Tx framestx
(Optional) Configure brief eltm event logs for mts Txbrief
(Optional) Configure detail eltm event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1195
E Commandsevent-history eltm category mts
Page 1340
event-history eltm category mtsevent-history eltm no category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure eltm event logseltm
Disable eltm event logs for categoryno
Configure eltm event logs for categorycategory
Configure eltm event logs for category mtsmts
(Optional) Configure eltm event logs for mts Rx framesrx
(Optional) Configure brief eltm event logs for mts Rxbrief
(Optional) Configure detail eltm event logs for mts Rxdetail
(Optional) Configure eltm event logs for mts Tx framestx
(Optional) Configure brief eltm event logs for mts Txbrief
(Optional) Configure detail eltm event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1196
E Commandsevent-history eltm category mts
Page 1341
event-history epp category allevent-history epp category all
Syntax Description
switch wide event history configurationevent-history
Configure EPP event logsepp
Configure EPP event logs for categorycategory
Configure EPP event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1197
E Commandsevent-history epp category all
Page 1342
event-history epp category allevent-history epp no category all
Syntax Description
switch wide event history configurationevent-history
Configure EPP event logsepp
Disable EPP event logs for categoryno
Configure EPP event logs for categorycategory
Configure EPP event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1198
E Commandsevent-history epp category all
Page 1343
event-history epp category fc2event-history epp category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure EPP event logsepp
Configure EPP event logs for categorycategory
Configure EPP event logs for category FC2fc2
(Optional) Configure EPP event logs for FC2 Rx framesrx
(Optional) Configure brief EPP event logs for FC2 Rxbrief
(Optional) Configure detail EPP event logs for FC2 Rxdetail
(Optional) Configure EPP event logs for FC2 Tx framestx
(Optional) Configure brief EPP event logs for FC2 Txbrief1
(Optional) Configure detail EPP event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1199
E Commandsevent-history epp category fc2
Page 1344
event-history epp category fc2event-history epp no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure EPP event logsepp
Disable EPP event logs for categoryno
Configure EPP event logs for categorycategory
Configure EPP event logs for category FC2fc2
(Optional) Configure EPP event logs for FC2 Rx framesrx
(Optional) Configure brief EPP event logs for FC2 Rxbrief
(Optional) Configure detail EPP event logs for FC2 Rxdetail
(Optional) Configure EPP event logs for FC2 Tx framestx
(Optional) Configure brief EPP event logs for FC2 Txbrief1
(Optional) Configure detail EPP event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1200
E Commandsevent-history epp category fc2
Page 1345
event-history epp category mtsevent-history epp category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure EPP event logsepp
Configure EPP event logs for categorycategory
Configure EPP event logs for category mtsmts
(Optional) Configure EPP event logs for mts Rx framesrx
(Optional) Configure brief EPP event logs for mts Rxbrief
(Optional) Configure detail EPP event logs for mts Rxdetail
(Optional) Configure EPP event logs for mts Tx framestx
(Optional) Configure brief EPP event logs for mts Txbrief1
(Optional) Configure detail EPP event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1201
E Commandsevent-history epp category mts
Page 1346
event-history epp category mtsevent-history epp no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure EPP event logsepp
Disable EPP event logs for categoryno
Configure EPP event logs for categorycategory
Configure EPP event logs for category mtsmts
(Optional) Configure EPP event logs for mts Rx framesrx
(Optional) Configure brief EPP event logs for mts Rxbrief
(Optional) Configure detail EPP event logs for mts Rxdetail
(Optional) Configure EPP event logs for mts Tx framestx
(Optional) Configure brief EPP event logs for mts Txbrief1
(Optional) Configure detail EPP event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1202
E Commandsevent-history epp category mts
Page 1347
event-history errors[no] event-history errors [ size { <size_in_text> | <bytes> | disable } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure event-history detailsevent-history
Errors history buffererrors
(Optional) Set the buffer sizesize
(Optional) Disable the bufferdisable
(Optional) Buffer sizesize_in_text
(Optional) Buffer size in bytesbytes
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1203
E Commandsevent-history errors
Page 1348
event-history ethpmevent-history ethpm { category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ] } | no category{ all | mts [ { rx [ { brief1 | detail1 } ] | tx [ { brief2 | detail2 } ] } ] } }
Syntax Description
switch wide event history configurationevent-history
Configure ethpm event logsethpm
Configure ethpm event logs for categorycategory
Configure ethpm event logs for category all eventsall
Configure ethpm event logs for category mtsmts
(Optional) Configure ethpm event logs for mts Rx framesrx
(Optional) Configure brief ethpm event logs for mts Rxbrief
(Optional) Configure detail ethpm event logs for mts Rxdetail
(Optional) Configure ethpm event logs for mts Tx framestx
(Optional) Configure brief ethpm event logs for mts Txbrief1
(Optional) Configure detail ethpm event logs for mts Txdetail1
Disable ethpm event logs for categoryno
Configure ethpm event logs for categorycategory
Configure ethpm event logs for category all eventsall
Configure ethpm event logs for category mtsmts
(Optional) Configure ethpm event logs for mts Rx framesrx
(Optional) Configure brief ethpm event logs for mts Rxbrief1
(Optional) Configure detail ethpm event logs for mts Rxdetail1
(Optional) Configure ethpm event logs for mts Tx framestx
(Optional) Configure brief ethpm event logs for mts Txbrief2
(Optional) Configure detail ethpm event logs for mts Txdetail2
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1204
E Commandsevent-history ethpm
Page 1349
event-history events[no] event-history events [ size { <size_in_text> | <bytes> | disable } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure event-history detailsevent-history
Events history bufferevents
(Optional) Set the buffer sizesize
(Optional) Disable the bufferdisable
(Optional) Buffer sizesize_in_text
(Optional) Buffer size in bytesbytes
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1205
E Commandsevent-history events
Page 1350
event-history exceptionlogevent-history exceptionlog { category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ] } | nocategory { all | mts [ { rx [ { brief1 | detail1 } ] | tx [ { brief2 | detail2 } ] } ] } }
Syntax Description
switch wide event history configurationevent-history
Configure expl manager event logsexceptionlog
Configure exceptionlog manager event logs for categorycategory
Configure explog eventlogs for category all eventsall
Configure exceptionlog manager event logs for category mtsmts
(Optional) Configure exceptionlogmanager event logs for mts Rx framesrx
(Optional) Configure brief exceptionlog manager event logs for mts Rxbrief
(Optional) Configure detail exceptionlog manager event logs for mtsRx
detail
(Optional) Configure exceptionlogmanager event logs for mts Tx framestx
(Optional) Configure brief exceptionlog manager event logs for mts Txbrief1
(Optional) Configure detail exceptionlog manager event logs for mtsTx
detail1
Disable exceptionlog manager event logs for categoryno
Configure exceptionlog manager event logs for categorycategory
Configure explog eventlogs for category all eventsall
Configure exceptionlog manager event logs for category mtsmts
(Optional) Configure exceptionlogmanager event logs for mts Rx framesrx
(Optional) Configure brief exceptionlog manager event logs for mts Rxbrief1
(Optional) Configure detail exceptionlog manager event logs for mtsRx
detail1
(Optional) Configure exceptionlogmanager event logs for mts Tx framestx
(Optional) Configure brief exceptionlog manager event logs for mts Txbrief2
(Optional) Configure detail exceptionlog manager event logs for mtsTx
detail2
Command Mode
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1206
E Commandsevent-history exceptionlog
Page 1351
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1207
E Commandsevent-history exceptionlog
Page 1352
event-history fcoe_mgr category allevent-history fcoe_mgr category all
Syntax Description
switch wide event history configurationevent-history
Configure fcoe_mgr event logsfcoe_mgr
Configure fcoe_mgr event logs for categorycategory
Configure fcoe_mgr event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1208
E Commandsevent-history fcoe_mgr category all
Page 1353
event-history fcoe_mgr category allevent-history fcoe_mgr no category all
Syntax Description
switch wide event history configurationevent-history
Configure fcoe_mgr event logsfcoe_mgr
Disable fcoe_mgr event logs for categoryno
Configure fcoe_mgr event logs for categorycategory
Configure fcoe_mgr event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1209
E Commandsevent-history fcoe_mgr category all
Page 1354
event-history fcoe_mgr category fc2event-history fcoe_mgr no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure fcoe_mgr event logsfcoe_mgr
Disable fcoe_mgr event logs for categoryno
Configure fcoe_mgr event logs for categorycategory
Configure fcoe_mgr event logs for category FC2fc2
(Optional) Configure fcoe_mgr event logs for FC2 Rx framesrx
(Optional) Configure brief fcoe_mgr event logs for FC2 Rxbrief
(Optional) Configure detail fcoe_mgr event logs for FC2 Rxdetail
(Optional) Configure fcoe_mgr event logs for FC2 Tx framestx
(Optional) Configure brief fcoe_mgr event logs for FC2 Txbrief1
(Optional) Configure detail fcoe_mgr event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1210
E Commandsevent-history fcoe_mgr category fc2
Page 1355
event-history fcoe_mgr category fc2event-history fcoe_mgr category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure fcoe_mgr event logsfcoe_mgr
Configure fcoe_mgr event logs for categorycategory
Configure fcoe_mgr event logs for category FC2fc2
(Optional) Configure fcoe_mgr event logs for FC2 Rx framesrx
(Optional) Configure brief fcoe_mgr event logs for FC2 Rxbrief
(Optional) Configure detail fcoe_mgr event logs for FC2 Rxdetail
(Optional) Configure fcoe_mgr event logs for FC2 Tx framestx
(Optional) Configure brief fcoe_mgr event logs for FC2 Txbrief1
(Optional) Configure detail fcoe_mgr event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1211
E Commandsevent-history fcoe_mgr category fc2
Page 1356
event-history fcoe_mgr category mtsevent-history fcoe_mgr no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure fcoe_mgr event logsfcoe_mgr
Disable fcoe_mgr event logs for categoryno
Configure fcoe_mgr event logs for categorycategory
Configure fcoe_mgr event logs for category mtsmts
(Optional) Configure fcoe_mgr event logs for mts Rx framesrx
(Optional) Configure brief fcoe_mgr event logs for mts Rxbrief
(Optional) Configure detail fcoe_mgr event logs for mts Rxdetail
(Optional) Configure fcoe_mgr event logs for mts Tx framestx
(Optional) Configure brief fcoe_mgr event logs for mts Txbrief1
(Optional) Configure detail fcoe_mgr event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1212
E Commandsevent-history fcoe_mgr category mts
Page 1357
event-history fcoe_mgr category mtsevent-history fcoe_mgr category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure fcoe_mgr event logsfcoe_mgr
Configure fcoe_mgr event logs for categorycategory
Configure fcoe_mgr event logs for category mtsmts
(Optional) Configure fcoe_mgr event logs for mts Rx framesrx
(Optional) Configure brief fcoe_mgr event logs for mts Rxbrief
(Optional) Configure detail fcoe_mgr event logs for mts Rxdetail
(Optional) Configure fcoe_mgr event logs for mts Tx framestx
(Optional) Configure brief fcoe_mgr event logs for mts Txbrief1
(Optional) Configure detail fcoe_mgr event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1213
E Commandsevent-history fcoe_mgr category mts
Page 1358
event-history hardware-telemetryevent-history hardware-telemetry { category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] }] } | no category { all | mts [ { rx [ { brief1 | detail1 } ] | tx [ { brief2 | detail2 } ] } ] } }
Syntax Description
switch wide event history configurationevent-history
Configure hardware-telemetry event logshardware-telemetry
Configure hardware-telemetry event logs for categorycategory
Configure hardware-telemetry event logs for category all eventsall
Configure hardware-telemetry event logs for category mtsmts
(Optional) Configure hardware-telemetry event logs for mts Rx framesrx
(Optional) Configure brief hardware-telemetry event logs for mts Rxbrief
(Optional) Configure detail hardware-telemetry event logs for mts Rxdetail
(Optional) Configure hardware-telemetry event logs for mts Tx framestx
(Optional) Configure brief hardware-telemetry event logs for mts Txbrief1
(Optional) Configure detail hardware-telemetry event logs for mts Txdetail1
Disable hardware-telemetry event logs for categoryno
Configure hw_telemetry event logs for categorycategory
Configure hardware-telemetry event logs for category all eventsall
Configure hardware-telemetry event logs for category mtsmts
(Optional) Configure hardware-telemetry event logs for mts Rx framesrx
(Optional) Configure brief hardware-telemetry event logs for mts Rxbrief1
(Optional) Configure detail hardware-telemetry event logs for mts Rxdetail1
(Optional) Configure hardware-telemetry event logs for mts Tx framestx
(Optional) Configure brief hardware-telemetry event logs for mts Txbrief2
(Optional) Configure detail hardware-telemetry event logs for mts Txdetail2
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1214
E Commandsevent-history hardware-telemetry
Page 1359
event-history im category mtsevent-history im no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure im event logsim
Disable im event logs for categoryno
Configure im event logs for categorycategory
Configure im event logs for category mtsmts
(Optional) Configure im event logs for mts Rx framesrx
(Optional) Configure brief im event logs for mts Rxbrief
(Optional) Configure detail im event logs for mts Rxdetail
(Optional) Configure im event logs for mts Tx framestx
(Optional) Configure brief im event logs for mts Txbrief1
(Optional) Configure detail im event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1215
E Commandsevent-history im category mts
Page 1360
event-history imp category allevent-history imp category all
Syntax Description
switch wide event history configurationevent-history
Configure imp event logsimp
Configure imp event logs for categorycategory
Configure imp event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1216
E Commandsevent-history imp category all
Page 1361
event-history imp category allevent-history imp no category all
Syntax Description
switch wide event history configurationevent-history
Configure imp event logsimp
Disable imp event logs for categoryno
Configure imp event logs for categorycategory
Configure imp event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1217
E Commandsevent-history imp category all
Page 1362
event-history imp category fc2event-history imp category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure imp event logsimp
Configure imp event logs for categorycategory
Configure imp event logs for category FC2fc2
(Optional) Configure imp event logs for FC2 Rx framesrx
(Optional) Configure brief imp event logs for FC2 Rxbrief
(Optional) Configure detail imp event logs for FC2 Rxdetail
(Optional) Configure imp event logs for FC2 Tx framestx
(Optional) Configure brief imp event logs for FC2 Txbrief1
(Optional) Configure detail imp event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1218
E Commandsevent-history imp category fc2
Page 1363
event-history imp category fc2event-history imp no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure imp event logsimp
Disable imp event logs for categoryno
Configure imp event logs for categorycategory
Configure imp event logs for category FC2fc2
(Optional) Configure imp event logs for FC2 Rx framesrx
(Optional) Configure brief imp event logs for FC2 Rxbrief
(Optional) Configure detail imp event logs for FC2 Rxdetail
(Optional) Configure imp event logs for FC2 Tx framestx
(Optional) Configure brief imp event logs for FC2 Txbrief1
(Optional) Configure detail imp event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1219
E Commandsevent-history imp category fc2
Page 1364
event-history imp category mtsevent-history imp category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure imp event logsimp
Configure imp event logs for categorycategory
Configure imp event logs for category mtsmts
(Optional) Configure imp event logs for mts Rx framesrx
(Optional) Configure brief imp event logs for mts Rxbrief
(Optional) Configure detail imp event logs for mts Rxdetail
(Optional) Configure imp event logs for mts Tx framestx
(Optional) Configure brief imp event logs for mts Txbrief1
(Optional) Configure detail imp event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1220
E Commandsevent-history imp category mts
Page 1365
event-history imp category mtsevent-history imp no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure imp event logsimp
Disable imp event logs for categoryno
Configure imp event logs for categorycategory
Configure imp event logs for category mtsmts
(Optional) Configure imp event logs for mts Rx framesrx
(Optional) Configure brief imp event logs for mts Rxbrief
(Optional) Configure detail imp event logs for mts Rxdetail
(Optional) Configure imp event logs for mts Tx framestx
(Optional) Configure brief imp event logs for mts Txbrief1
(Optional) Configure detail imp event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1221
E Commandsevent-history imp category mts
Page 1366
event-history keystoreevent-history { keystore | sksd } { category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]} | no category { all | mts [ { rx [ { brief1 | detail1 } ] | tx [ { brief2 | detail2 } ] } ] } }
Syntax Description
switch wide event history configurationevent-history
Configure keystore event logskeystore
Configure keystore/sksd event logssksd
Configure keystore event logs for categorycategory
Configure keystore event logs for category all eventsall
Configure keystore event logs for category mtsmts
(Optional) Configure keystore event logs for mts Rx framesrx
(Optional) Configure brief keystore event logs for mts Rxbrief
(Optional) Configure detail keystore event logs for mts Rxdetail
(Optional) Configure keystore event logs for mts Tx framestx
(Optional) Configure brief keystore event logs for mts Txbrief1
(Optional) Configure detail keystore event logs for mts Txdetail1
Disable keystore event logs for categoryno
Configure keystore event logs for categorycategory
Configure keystore event logs for category all eventsall
Configure keystore event logs for category mtsmts
(Optional) Configure keystore event logs for mts Rx framesrx
(Optional) Configure brief keystore event logs for mts Rxbrief1
(Optional) Configure detail keystore event logs for mts Rxdetail1
(Optional) Configure keystore event logs for mts Tx framestx
(Optional) Configure brief keystore event logs for mts Txbrief2
(Optional) Configure detail keystore event logs for mts Txdetail2
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1222
E Commandsevent-history keystore
Page 1367
event-history lacp category allevent-history lacp category all
Syntax Description
switch wide event history configurationevent-history
Configure lacp event logslacp
Configure lacp event logs for categorycategory
Configure lacp event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1223
E Commandsevent-history lacp category all
Page 1368
event-history lacp category allevent-history lacp no category all
Syntax Description
switch wide event history configurationevent-history
Configure lacp event logslacp
Disable lacp event logs for categoryno
Configure lacp event logs for categorycategory
Configure lacp event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1224
E Commandsevent-history lacp category all
Page 1369
event-history lacp category fc2event-history lacp category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure lacp event logslacp
Configure lacp event logs for categorycategory
Configure lacp event logs for category FC2fc2
(Optional) Configure lacp event logs for FC2 Rx framesrx
(Optional) Configure brief lacp event logs for FC2 Rxbrief
(Optional) Configure detail lacp event logs for FC2 Rxdetail
(Optional) Configure lacp event logs for FC2 Tx framestx
(Optional) Configure brief lacp event logs for FC2 Txbrief1
(Optional) Configure detail lacp event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1225
E Commandsevent-history lacp category fc2
Page 1370
event-history lacp category fc2event-history lacp no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure lacp event logslacp
Disable lacp event logs for categoryno
Configure lacp event logs for categorycategory
Configure lacp event logs for category FC2fc2
(Optional) Configure lacp event logs for FC2 Rx framesrx
(Optional) Configure brief lacp event logs for FC2 Rxbrief
(Optional) Configure detail lacp event logs for FC2 Rxdetail
(Optional) Configure lacp event logs for FC2 Tx framestx
(Optional) Configure brief lacp event logs for FC2 Txbrief1
(Optional) Configure detail lacp event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1226
E Commandsevent-history lacp category fc2
Page 1371
event-history lacp category mtsevent-history lacp no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure lacp event logslacp
Disable lacp event logs for categoryno
Configure lacp event logs for categorycategory
Configure lacp event logs for category mtsmts
(Optional) Configure lacp event logs for mts Rx framesrx
(Optional) Configure brief lacp event logs for mts Rxbrief
(Optional) Configure detail lacp event logs for mts Rxdetail
(Optional) Configure lacp event logs for mts Tx framestx
(Optional) Configure brief lacp event logs for mts Txbrief1
(Optional) Configure detail lacp event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1227
E Commandsevent-history lacp category mts
Page 1372
event-history lacp category mtsevent-history lacp category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure lacp event logslacp
Configure lacp event logs for categorycategory
Configure lacp event logs for category mtsmts
(Optional) Configure lacp event logs for mts Rx framesrx
(Optional) Configure brief lacp event logs for mts Rxbrief
(Optional) Configure detail lacp event logs for mts Rxdetail
(Optional) Configure lacp event logs for mts Tx framestx
(Optional) Configure brief lacp event logs for mts Txbrief1
(Optional) Configure detail lacp event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1228
E Commandsevent-history lacp category mts
Page 1373
event-history lem-mgr category allevent-history lem-mgr no category all
Syntax Description
switch wide event history configurationevent-history
Disable lem-mgr event logs for categoryno
Configure lem-mgr event logs for categorycategory
Configure lem-mgr event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1229
E Commandsevent-history lem-mgr category all
Page 1374
event-history lem-mgr category allevent-history lem-mgr category all
Syntax Description
switch wide event history configurationevent-history
Configure lem-mgr event logs for categorycategory
Configure lem-mgr event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1230
E Commandsevent-history lem-mgr category all
Page 1375
event-history lem-mgr category fc2event-history lem-mgr no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Disable lem-mgr event logs for categoryno
Configure lem-mgr event logs for categorycategory
Configure lem-mgr event logs for category FC2fc2
(Optional) Configure lem-mgr event logs for FC2 Rx framesrx
(Optional) Configure brief lem-mgr event logs for FC2 Rxbrief
(Optional) Configure detail lem-mgr event logs for FC2 Rxdetail
(Optional) Configure lem-mgr event logs for FC2 Tx framestx
(Optional) Configure brief lem-mgr event logs for FC2 Txbrief
(Optional) Configure detail lem-mgr event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1231
E Commandsevent-history lem-mgr category fc2
Page 1376
event-history lem-mgr category fc2event-history lem-mgr category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure lem-mgr event logs for categorycategory
Configure lem-mgr event logs for category FC2fc2
(Optional) Configure lem-mgr event logs for FC2 Rx framesrx
(Optional) Configure brief lem-mgr event logs for FC2 Rxbrief
(Optional) Configure detail lem-mgr event logs for FC2 Rxdetail
(Optional) Configure lem-mgr event logs for FC2 Tx framestx
(Optional) Configure brief lem-mgr event logs for FC2 Txbrief
(Optional) Configure detail lem-mgr event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1232
E Commandsevent-history lem-mgr category fc2
Page 1377
event-history lem-mgr category mtsevent-history lem-mgr category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure lem-mgr event logs for categorycategory
Configure lem-mgr event logs for category mtsmts
(Optional) Configure lem-mgr event logs for mts Rx framesrx
(Optional) Configure brief lem-mgr event logs for mts Rxbrief
(Optional) Configure detail lem-mgr event logs for mts Rxdetail
(Optional) Configure lem-mgr event logs for mts Tx framestx
(Optional) Configure brief lem-mgr event logs for mts Txbrief
(Optional) Configure detail lem-mgr event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1233
E Commandsevent-history lem-mgr category mts
Page 1378
event-history lem-mgr category mtsevent-history lem-mgr no category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Disable lem-mgr event logs for categoryno
Configure lem-mgr event logs for categorycategory
Configure lem-mgr event logs for category mtsmts
(Optional) Configure lem-mgr event logs for mts Rx framesrx
(Optional) Configure brief lem-mgr event logs for mts Rxbrief
(Optional) Configure detail lem-mgr event logs for mts Rxdetail
(Optional) Configure lem-mgr event logs for mts Tx framestx
(Optional) Configure brief lem-mgr event logs for mts Txbrief
(Optional) Configure detail lem-mgr event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1234
E Commandsevent-history lem-mgr category mts
Page 1379
event-history licenseevent-history license { category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ] } | no category{ all | mts [ { rx [ { brief1 | detail1 } ] | tx [ { brief2 | detail2 } ] } ] } }
Syntax Description
switch wide event history configurationevent-history
Configure license manager event logslicense
Configure license manager event logs for categorycategory
Configure license manager event logs for category all eventsall
Configure license manager event logs for category mtsmts
(Optional) Configure license manager event logs for mts Rx framesrx
(Optional) Configure brief license manager event logs for mts Rxbrief
(Optional) Configure detail license manager event logs for mts Rxdetail
(Optional) Configure license manager event logs for mts Tx framestx
(Optional) Configure brief license manager event logs for mts Txbrief1
(Optional) Configure detail license manager event logs for mts Txdetail1
Disable license manager event logs for categoryno
Configure license manager event logs for categorycategory
Configure license manager event logs for category all eventsall
Configure license manager event logs for category mtsmts
(Optional) Configure license manager event logs for mts Rx framesrx
(Optional) Configure brief license manager event logs for mts Rxbrief1
(Optional) Configure detail license manager event logs for mts Rxdetail1
(Optional) Configure license manager event logs for mts Tx framestx
(Optional) Configure brief license manager event logs for mts Txbrief2
(Optional) Configure detail license manager event logs for mts Txdetail2
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1235
E Commandsevent-history license
Page 1380
event-history lldp category allevent-history lldp category all
Syntax Description
switch wide event history configurationevent-history
Configure lldp event logslldp
Configure lldp event logs for categorycategory
Configure lldp event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1236
E Commandsevent-history lldp category all
Page 1381
event-history lldp category allevent-history lldp no category all
Syntax Description
switch wide event history configurationevent-history
Configure lldp event logslldp
Disable lldp event logs for categoryno
Configure lldp event logs for categorycategory
Configure lldp event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1237
E Commandsevent-history lldp category all
Page 1382
event-history lldp category fc2event-history lldp no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure lldp event logslldp
Disable lldp event logs for categoryno
Configure lldp event logs for categorycategory
Configure lldp event logs for category FC2fc2
(Optional) Configure lldp event logs for FC2 Rx framesrx
(Optional) Configure brief lldp event logs for FC2 Rxbrief
(Optional) Configure detail lldp event logs for FC2 Rxdetail
(Optional) Configure lldp event logs for FC2 Tx framestx
(Optional) Configure brief lldp event logs for FC2 Txbrief1
(Optional) Configure detail lldp event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1238
E Commandsevent-history lldp category fc2
Page 1383
event-history lldp category fc2event-history lldp category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure lldp event logslldp
Configure lldp event logs for categorycategory
Configure lldp event logs for category FC2fc2
(Optional) Configure lldp event logs for FC2 Rx framesrx
(Optional) Configure brief lldp event logs for FC2 Rxbrief
(Optional) Configure detail lldp event logs for FC2 Rxdetail
(Optional) Configure lldp event logs for FC2 Tx framestx
(Optional) Configure brief lldp event logs for FC2 Txbrief1
(Optional) Configure detail lldp event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1239
E Commandsevent-history lldp category fc2
Page 1384
event-history lldp category mtsevent-history lldp category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure lldp event logslldp
Configure lldp event logs for categorycategory
Configure lldp event logs for category mtsmts
(Optional) Configure lldp event logs for mts Rx framesrx
(Optional) Configure brief lldp event logs for mts Rxbrief
(Optional) Configure detail lldp event logs for mts Rxdetail
(Optional) Configure lldp event logs for mts Tx framestx
(Optional) Configure brief lldp event logs for mts Txbrief1
(Optional) Configure detail lldp event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1240
E Commandsevent-history lldp category mts
Page 1385
event-history lldp category mtsevent-history lldp no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure lldp event logslldp
Disable lldp event logs for categoryno
Configure lldp event logs for categorycategory
Configure lldp event logs for category mtsmts
(Optional) Configure lldp event logs for mts Rx framesrx
(Optional) Configure brief lldp event logs for mts Rxbrief
(Optional) Configure detail lldp event logs for mts Rxdetail
(Optional) Configure lldp event logs for mts Tx framestx
(Optional) Configure brief lldp event logs for mts Txbrief1
(Optional) Configure detail lldp event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1241
E Commandsevent-history lldp category mts
Page 1386
event-history m2rib category allevent-history m2rib category all
Syntax Description
switch wide event history configurationevent-history
Configure m2rib event logsm2rib
Configure m2rib event logs for categorycategory
Configure m2rib event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1242
E Commandsevent-history m2rib category all
Page 1387
event-history mfdm category allevent-history mfdm category all
Syntax Description
switch wide event history configurationevent-history
Configure mfdm event logsmfdm
Configure mfdm event logs for categorycategory
Configure mfdm event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1243
E Commandsevent-history mfdm category all
Page 1388
event-history mfdm category allevent-history mfdm no category all
Syntax Description
switch wide event history configurationevent-history
Configure mfdm event logsmfdm
Disable mfdm event logs for categoryno
Configure mfdm event logs for categorycategory
Configure mfdm event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1244
E Commandsevent-history mfdm category all
Page 1389
event-history mfdm category fc2event-history mfdm no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure mfdm event logsmfdm
Disable mfdm event logs for categoryno
Configure mfdm event logs for categorycategory
Configure mfdm event logs for category FC2fc2
(Optional) Configure mfdm event logs for FC2 Rx framesrx
(Optional) Configure brief mfdm event logs for FC2 Rxbrief
(Optional) Configure detail mfdm event logs for FC2 Rxdetail
(Optional) Configure mfdm event logs for FC2 Tx framestx
(Optional) Configure brief mfdm event logs for FC2 Txbrief
(Optional) Configure detail mfdm event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1245
E Commandsevent-history mfdm category fc2
Page 1390
event-history mfdm category fc2event-history mfdm category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure mfdm event logsmfdm
Configure mfdm event logs for categorycategory
Configure mfdm event logs for category FC2fc2
(Optional) Configure mfdm event logs for FC2 Rx framesrx
(Optional) Configure brief mfdm event logs for FC2 Rxbrief
(Optional) Configure detail mfdm event logs for FC2 Rxdetail
(Optional) Configure mfdm event logs for FC2 Tx framestx
(Optional) Configure brief mfdm event logs for FC2 Txbrief
(Optional) Configure detail mfdm event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1246
E Commandsevent-history mfdm category fc2
Page 1391
event-history mfdm category mtsevent-history mfdm no category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure mfdm event logsmfdm
Disable mfdm event logs for categoryno
Configure mfdm event logs for categorycategory
Configure mfdm event logs for category mtsmts
(Optional) Configure mfdm event logs for mts Rx framesrx
(Optional) Configure brief mfdm event logs for mts Rxbrief
(Optional) Configure detail mfdm event logs for mts Rxdetail
(Optional) Configure mfdm event logs for mts Tx framestx
(Optional) Configure brief mfdm event logs for mts Txbrief
(Optional) Configure detail mfdm event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1247
E Commandsevent-history mfdm category mts
Page 1392
event-history mfdm category mtsevent-history mfdm category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure mfdm event logsmfdm
Configure mfdm event logs for categorycategory
Configure mfdm event logs for category mtsmts
(Optional) Configure mfdm event logs for mts Rx framesrx
(Optional) Configure brief mfdm event logs for mts Rxbrief
(Optional) Configure detail mfdm event logs for mts Rxdetail
(Optional) Configure mfdm event logs for mts Tx framestx
(Optional) Configure brief mfdm event logs for mts Txbrief
(Optional) Configure detail mfdm event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1248
E Commandsevent-history mfdm category mts
Page 1393
event-history mmode category allevent-history mmode [ no ] category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ] }
Syntax Description
switch wide event history configurationevent-history
Configure mmode event logsmmode
(Optional) Disable mmode event logs for categoryno
Configure mmode event logs for categorycategory
Configure mmode event logs for category all eventsall
Configure mmode event logs for category mtsmts
(Optional) Configure mmode event logs for mts Rx framesrx
(Optional) Configure brief mmode event logs for mts Rxbrief
(Optional) Configure detail mmode event logs for mts Rxdetail
(Optional) Configure mmode event logs for mts Tx framestx
(Optional) Configure brief mmode event logs for mts Txbrief1
(Optional) Configure detail mmode event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1249
E Commandsevent-history mmode category all
Page 1394
event-history moduleevent-history module { category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ] } | no category{ all | mts [ { rx [ { brief1 | detail1 } ] | tx [ { brief2 | detail2 } ] } ] } }
Syntax Description
switch wide event history configurationevent-history
Configure module event logsmodule
Configure module event logs for categorycategory
Configure module event logs for category all eventsall
Configure module event logs for category mtsmts
(Optional) Configure module event logs for mts Rx framesrx
(Optional) Configure brief module event logs for mts Rxbrief
(Optional) Configure detail module event logs for mts Rxdetail
(Optional) Configure module event logs for mts Tx framestx
(Optional) Configure brief module event logs for mts Txbrief1
(Optional) Configure detail module event logs for mts Txdetail1
Disable module event logs for categoryno
Configure module event logs for categorycategory
Configure module event logs for category all eventsall
Configure module event logs for category mtsmts
(Optional) Configure module event logs for mts Rx framesrx
(Optional) Configure brief module event logs for mts Rxbrief1
(Optional) Configure detail module event logs for mts Rxdetail1
(Optional) Configure module event logs for mts Tx framestx
(Optional) Configure brief module event logs for mts Txbrief2
(Optional) Configure detail module event logs for mts Txdetail2
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1250
E Commandsevent-history module
Page 1395
event-history npv category allevent-history npv no category all
Syntax Description
switch wide event history configurationevent-history
Configure NPV event logsnpv
Disable NPV event logs for categoryno
Configure NPV event logs for categorycategory
Configure NPV event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1251
E Commandsevent-history npv category all
Page 1396
event-history npv category allevent-history npv category all
Syntax Description
switch wide event history configurationevent-history
Configure NPV event logsnpv
Configure NPV event logs for categorycategory
Configure NPV event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1252
E Commandsevent-history npv category all
Page 1397
event-history npv category fc2event-history npv no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure NPV event logsnpv
Disable NPV event logs for categoryno
Configure NPV event logs for categorycategory
Configure NPV event logs for category FC2fc2
(Optional) Configure NPV event logs for FC2 Rx framesrx
(Optional) Configure brief NPV event logs for FC2 Rxbrief
(Optional) Configure detail NPV event logs for FC2 Rxdetail
(Optional) Configure NPV event logs for FC2 Tx framestx
(Optional) Configure brief NPV event logs for FC2 Txbrief
(Optional) Configure detail NPV event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1253
E Commandsevent-history npv category fc2
Page 1398
event-history npv category fc2event-history npv category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure NPV event logsnpv
Configure NPV event logs for categorycategory
Configure NPV event logs for category FC2fc2
(Optional) Configure NPV event logs for FC2 Rx framesrx
(Optional) Configure brief NPV event logs for FC2 Rxbrief
(Optional) Configure detail NPV event logs for FC2 Rxdetail
(Optional) Configure NPV event logs for FC2 Tx framestx
(Optional) Configure brief NPV event logs for FC2 Txbrief
(Optional) Configure detail NPV event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1254
E Commandsevent-history npv category fc2
Page 1399
event-history npv category mtsevent-history npv category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure NPV event logsnpv
Configure NPV event logs for categorycategory
Configure NPV event logs for category mtsmts
(Optional) Configure NPV event logs for mts Rx framesrx
(Optional) Configure brief NPV event logs for mts Rxbrief
(Optional) Configure detail NPV event logs for mts Rxdetail
(Optional) Configure NPV event logs for mts Tx framestx
(Optional) Configure brief NPV event logs for mts Txbrief
(Optional) Configure detail NPV event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1255
E Commandsevent-history npv category mts
Page 1400
event-history npv category mtsevent-history npv no category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure NPV event logsnpv
Disable NPV event logs for categoryno
Configure NPV event logs for categorycategory
Configure NPV event logs for category mtsmts
(Optional) Configure NPV event logs for mts Rx framesrx
(Optional) Configure brief NPV event logs for mts Rxbrief
(Optional) Configure detail NPV event logs for mts Rxdetail
(Optional) Configure NPV event logs for mts Tx framestx
(Optional) Configure brief NPV event logs for mts Txbrief
(Optional) Configure detail NPV event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1256
E Commandsevent-history npv category mts
Page 1401
event-history pfstat category allevent-history pfstat category all
Syntax Description
switch wide event history configurationevent-history
Configure pfstat event logspfstat
Configure pfstat event logs for categorycategory
Configure pfstat event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1257
E Commandsevent-history pfstat category all
Page 1402
event-history pfstat category allevent-history pfstat no category all
Syntax Description
switch wide event history configurationevent-history
Configure pfstat event logspfstat
Disable pfstat event logs for categoryno
Configure pfstat event logs for categorycategory
Configure pfstat event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1258
E Commandsevent-history pfstat category all
Page 1403
event-history pfstat category fc2event-history pfstat no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure pfstat event logspfstat
Disable pfstat event logs for categoryno
Configure pfstat event logs for categorycategory
Configure pfstat event logs for category FC2fc2
(Optional) Configure pfstat event logs for FC2 Rx framesrx
(Optional) Configure brief pfstat event logs for FC2 Rxbrief
(Optional) Configure detail pfstat event logs for FC2 Rxdetail
(Optional) Configure pfstat event logs for FC2 Tx framestx
(Optional) Configure brief pfstat event logs for FC2 Txbrief
(Optional) Configure detail pfstat event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1259
E Commandsevent-history pfstat category fc2
Page 1404
event-history pfstat category fc2event-history pfstat category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure pfstat event logspfstat
Configure pfstat event logs for categorycategory
Configure pfstat event logs for category FC2fc2
(Optional) Configure pfstat event logs for FC2 Rx framesrx
(Optional) Configure brief pfstat event logs for FC2 Rxbrief
(Optional) Configure detail pfstat event logs for FC2 Rxdetail
(Optional) Configure pfstat event logs for FC2 Tx framestx
(Optional) Configure brief pfstat event logs for FC2 Txbrief
(Optional) Configure detail pfstat event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1260
E Commandsevent-history pfstat category fc2
Page 1405
event-history pfstat category mtsevent-history pfstat category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure pfstat event logspfstat
Configure pfstat event logs for categorycategory
Configure pfstat event logs for category mtsmts
(Optional) Configure pfstat event logs for mts Rx framesrx
(Optional) Configure brief pfstat event logs for mts Rxbrief
(Optional) Configure detail pfstat event logs for mts Rxdetail
(Optional) Configure pfstat event logs for mts Tx framestx
(Optional) Configure brief pfstat event logs for mts Txbrief
(Optional) Configure detail pfstat event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1261
E Commandsevent-history pfstat category mts
Page 1406
event-history pfstat category mtsevent-history pfstat no category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure pfstat event logspfstat
Disable pfstat event logs for categoryno
Configure pfstat event logs for categorycategory
Configure pfstat event logs for category mtsmts
(Optional) Configure pfstat event logs for mts Rx framesrx
(Optional) Configure brief pfstat event logs for mts Rxbrief
(Optional) Configure detail pfstat event logs for mts Rxdetail
(Optional) Configure pfstat event logs for mts Tx framestx
(Optional) Configure brief pfstat event logs for mts Txbrief
(Optional) Configure detail pfstat event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1262
E Commandsevent-history pfstat category mts
Page 1407
event-history platform buffer-sizeevent-history platform buffer-size <i0>
Syntax Description
switch wide event history configurationevent-history
Configure platform event logsplatform
Configure platform event logs buffer sizebuffer-size
please enter buffer sizei0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1263
E Commandsevent-history platform buffer-size
Page 1408
event-history platform category allevent-history platform category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ] }
Syntax Description
switch wide event history configurationevent-history
Configure platform event logsplatform
Configure platform event logs for categorycategory
Configure platform event logs for category all eventsall
Configure platform event logs for category mtsmts
(Optional) Configure platform event logs for mts Rx framesrx
(Optional) Configure brief platform event logs for mts Rxbrief
(Optional) Configure detail platform event logs for mts Rxdetail
(Optional) Configure platform event logs for mts Tx framestx
(Optional) Configure brief platform event logs for mts Txbrief1
(Optional) Configure detail platform event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1264
E Commandsevent-history platform category all
Page 1409
event-history platform category allevent-history platform no category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ] }
Syntax Description
switch wide event history configurationevent-history
Configure platform event logsplatform
Disable platform event logs for categoryno
Configure platform event logs for categorycategory
Configure platform event logs for category all eventsall
Configure platform event logs for category mtsmts
(Optional) Configure platform event logs for mts Rx framesrx
(Optional) Configure brief platform event logs for mts Rxbrief
(Optional) Configure detail platform event logs for mts Rxdetail
(Optional) Configure platform event logs for mts Tx framestx
(Optional) Configure brief platform event logs for mts Txbrief1
(Optional) Configure detail platform event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1265
E Commandsevent-history platform category all
Page 1410
event-history pltfm_config category allevent-history pltfm_config category all
Syntax Description
switch wide event history configurationevent-history
Configure pltfm_config event logspltfm_config
Configure pltfm_config event logs for categorycategory
Configure pltfm_config event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1266
E Commandsevent-history pltfm_config category all
Page 1411
event-history pltfm_config category allevent-history pltfm_config no category all
Syntax Description
switch wide event history configurationevent-history
Configure pltfm_config event logspltfm_config
Disable pltfm_config event logs for categoryno
Configure pltfm_config event logs for categorycategory
Configure pltfm_config event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1267
E Commandsevent-history pltfm_config category all
Page 1412
event-history pltfm_config category fc2event-history pltfm_config category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure pltfm_config event logspltfm_config
Configure pltfm_config event logs for categorycategory
Configure pltfm_config event logs for category FC2fc2
(Optional) Configure pltfm_config event logs for FC2 Rx framesrx
(Optional) Configure brief pltfm_config event logs for FC2 Rxbrief
(Optional) Configure detail pltfm_config event logs for FC2 Rxdetail
(Optional) Configure pltfm_config event logs for FC2 Tx framestx
(Optional) Configure brief pltfm_config event logs for FC2 Txbrief1
(Optional) Configure detail pltfm_config event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1268
E Commandsevent-history pltfm_config category fc2
Page 1413
event-history pltfm_config category fc2event-history pltfm_config no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure pltfm_config event logspltfm_config
Disable pltfm_config event logs for categoryno
Configure pltfm_config event logs for categorycategory
Configure pltfm_config event logs for category FC2fc2
(Optional) Configure pltfm_config event logs for FC2 Rx framesrx
(Optional) Configure brief pltfm_config event logs for FC2 Rxbrief
(Optional) Configure detail pltfm_config event logs for FC2 Rxdetail
(Optional) Configure pltfm_config event logs for FC2 Tx framestx
(Optional) Configure brief pltfm_config event logs for FC2 Txbrief1
(Optional) Configure detail pltfm_config event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1269
E Commandsevent-history pltfm_config category fc2
Page 1414
event-history pltfm_config category mtsevent-history pltfm_config category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure pltfm_config event logspltfm_config
Configure pltfm_config event logs for categorycategory
Configure pltfm_config event logs for category mtsmts
(Optional) Configure pltfm_config event logs for mts Rx framesrx
(Optional) Configure brief pltfm_config event logs for mts Rxbrief
(Optional) Configure detail pltfm_config event logs for mts Rxdetail
(Optional) Configure pltfm_config event logs for mts Tx framestx
(Optional) Configure brief pltfm_config event logs for mts Txbrief1
(Optional) Configure detail pltfm_config event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1270
E Commandsevent-history pltfm_config category mts
Page 1415
event-history pltfm_config category mtsevent-history pltfm_config no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure pltfm_config event logspltfm_config
Disable pltfm_config event logs for categoryno
Configure pltfm_config event logs for categorycategory
Configure pltfm_config event logs for category mtsmts
(Optional) Configure pltfm_config event logs for mts Rx framesrx
(Optional) Configure brief pltfm_config event logs for mts Rxbrief
(Optional) Configure detail pltfm_config event logs for mts Rxdetail
(Optional) Configure pltfm_config event logs for mts Tx framestx
(Optional) Configure brief pltfm_config event logs for mts Txbrief1
(Optional) Configure detail pltfm_config event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1271
E Commandsevent-history pltfm_config category mts
Page 1416
event-history pluginevent-history plugin { category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ] } | no category{ all | mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ] } }
Syntax Description
switch wide event history configurationevent-history
Configure plugin event logsplugin
Configure plugin event logs for categorycategory
Configure plugin event logs for category all eventsall
Configure plugin event logs for category mtsmts
(Optional) Configure plugin event logs for mts Rx framesrx
(Optional) Configure brief plugin event logs for mts Rxbrief
(Optional) Configure detail plugin event logs for mts Rxdetail
(Optional) Configure plugin event logs for mts Tx framestx
(Optional) Configure brief plugin event logs for mts Txbrief
(Optional) Configure detail plugin event logs for mts Txdetail
Disable plugin event logs for categoryno
Configure plugin event logs for categorycategory
Configure plugin event logs for category all eventsall
Configure plugin event logs for category mtsmts
(Optional) Configure plugin event logs for mts Rx framesrx
(Optional) Configure brief plugin event logs for mts Rxbrief
(Optional) Configure detail plugin event logs for mts Rxdetail
(Optional) Configure plugin event logs for mts Tx framestx
(Optional) Configure brief plugin event logs for mts Txbrief
(Optional) Configure detail plugin event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1272
E Commandsevent-history plugin
Page 1417
event-history poap category allevent-history poap category all
Syntax Description
switch wide event history configurationevent-history
Configure poap event logspoap
Configure poap event logs for categorycategory
Configure poap event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1273
E Commandsevent-history poap category all
Page 1418
event-history poap category allevent-history poap no category all
Syntax Description
switch wide event history configurationevent-history
Configure poap event logspoap
Disable poap event logs for categoryno
Configure poap event logs for categorycategory
Configure poap event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1274
E Commandsevent-history poap category all
Page 1419
event-history poap category fc2event-history poap category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure poap event logspoap
Configure poap event logs for categorycategory
Configure poap event logs for category FC2fc2
(Optional) Configure poap event logs for FC2 Rx framesrx
(Optional) Configure brief poap event logs for FC2 Rxbrief
(Optional) Configure detail poap event logs for FC2 Rxdetail
(Optional) Configure poap event logs for FC2 Tx framestx
(Optional) Configure brief poap event logs for FC2 Txbrief1
(Optional) Configure detail poap event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1275
E Commandsevent-history poap category fc2
Page 1420
event-history poap category fc2event-history poap no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure poap event logspoap
Disable poap event logs for categoryno
Configure poap event logs for categorycategory
Configure poap event logs for category FC2fc2
(Optional) Configure poap event logs for FC2 Rx framesrx
(Optional) Configure brief poap event logs for FC2 Rxbrief
(Optional) Configure detail poap event logs for FC2 Rxdetail
(Optional) Configure poap event logs for FC2 Tx framestx
(Optional) Configure brief poap event logs for FC2 Txbrief1
(Optional) Configure detail poap event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1276
E Commandsevent-history poap category fc2
Page 1421
event-history poap category mtsevent-history poap no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure poap event logspoap
Disable poap event logs for categoryno
Configure poap event logs for categorycategory
Configure poap event logs for category mtsmts
(Optional) Configure poap event logs for mts Rx framesrx
(Optional) Configure brief poap event logs for mts Rxbrief
(Optional) Configure detail poap event logs for mts Rxdetail
(Optional) Configure poap event logs for mts Tx framestx
(Optional) Configure brief poap event logs for mts Txbrief1
(Optional) Configure detail poap event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1277
E Commandsevent-history poap category mts
Page 1422
event-history poap category mtsevent-history poap category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure poap event logspoap
Configure poap event logs for categorycategory
Configure poap event logs for category mtsmts
(Optional) Configure poap event logs for mts Rx framesrx
(Optional) Configure brief poap event logs for mts Rxbrief
(Optional) Configure detail poap event logs for mts Rxdetail
(Optional) Configure poap event logs for mts Tx framestx
(Optional) Configure brief poap event logs for mts Txbrief1
(Optional) Configure detail poap event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1278
E Commandsevent-history poap category mts
Page 1423
event-history port-profile category allevent-history port-profile [ no ] category all
Syntax Description
switch wide event history configurationevent-history
Configure port-profile event logsport-profile
Configure port-profile event logs for categorycategory
(Optional) Disable port-profile event logs for categoryno
Configure port-profile event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1279
E Commandsevent-history port-profile category all
Page 1424
event-history port-profile category mtsevent-history port-profile [ no ] category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure port-profile event logsport-profile
(Optional) Disable port-profile event logs for categoryno
Configure port-profile event logs for categorycategory
Configure port-profile event logs for category mtsmts
(Optional) Configure port-profile event logs for mts Rx framesrx
(Optional) Configure brief port-profile event logs for mts Rxbrief
(Optional) Configure detail port-profile event logs for mts Rxdetail
(Optional) Configure port-profile event logs for mts Tx framestx
(Optional) Configure brief port-profile event logs for mts Txbrief1
(Optional) Configure detail port-profile event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1280
E Commandsevent-history port-profile category mts
Page 1425
event-history port-resources category allevent-history port-resources category all
Syntax Description
switch wide event history configurationevent-history
Configure prm event logsport-resources
Configure prm event logs for categorycategory
Configure prm event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1281
E Commandsevent-history port-resources category all
Page 1426
event-history port-resources category allevent-history port-resources no category all
Syntax Description
switch wide event history configurationevent-history
Configure prm event logsport-resources
Disable prm event logs for categoryno
Configure prm event logs for categorycategory
Configure prm event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1282
E Commandsevent-history port-resources category all
Page 1427
event-history port-resources category fc2event-history port-resources no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure prm event logsport-resources
Disable prm event logs for categoryno
Configure prm event logs for categorycategory
Configure prm event logs for category FC2fc2
(Optional) Configure prm event logs for FC2 Rx framesrx
(Optional) Configure brief prm event logs for FC2 Rxbrief
(Optional) Configure detail prm event logs for FC2 Rxdetail
(Optional) Configure prm event logs for FC2 Tx framestx
(Optional) Configure brief prm event logs for FC2 Txbrief1
(Optional) Configure detail prm event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1283
E Commandsevent-history port-resources category fc2
Page 1428
event-history port-resources category fc2event-history port-resources category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure prm event logsport-resources
Configure prm event logs for categorycategory
Configure prm event logs for category FC2fc2
(Optional) Configure prm event logs for FC2 Rx framesrx
(Optional) Configure brief prm event logs for FC2 Rxbrief
(Optional) Configure detail prm event logs for FC2 Rxdetail
(Optional) Configure prm event logs for FC2 Tx framestx
(Optional) Configure brief prm event logs for FC2 Txbrief1
(Optional) Configure detail prm event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1284
E Commandsevent-history port-resources category fc2
Page 1429
event-history port-resources category mtsevent-history port-resources no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure prm event logsport-resources
Disable prm event logs for categoryno
Configure prm event logs for categorycategory
Configure prm event logs for category mtsmts
(Optional) Configure prm event logs for mts Rx framesrx
(Optional) Configure brief prm event logs for mts Rxbrief
(Optional) Configure detail prm event logs for mts Rxdetail
(Optional) Configure prm event logs for mts Tx framestx
(Optional) Configure brief prm event logs for mts Txbrief1
(Optional) Configure detail prm event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1285
E Commandsevent-history port-resources category mts
Page 1430
event-history port-resources category mtsevent-history port-resources category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure prm event logsport-resources
Configure prm event logs for categorycategory
Configure prm event logs for category mtsmts
(Optional) Configure prm event logs for mts Rx framesrx
(Optional) Configure brief prm event logs for mts Rxbrief
(Optional) Configure detail prm event logs for mts Rxdetail
(Optional) Configure prm event logs for mts Tx framestx
(Optional) Configure brief prm event logs for mts Txbrief1
(Optional) Configure detail prm event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1286
E Commandsevent-history port-resources category mts
Page 1431
event-history port-security category allevent-history port-security no category all
Syntax Description
switch wide event history configurationevent-history
Configure port-security event logsport-security
Disable port-security event logs for categoryno
Configure port-security event logs for categorycategory
Configure port-security event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1287
E Commandsevent-history port-security category all
Page 1432
event-history port-security category allevent-history port-security category all
Syntax Description
switch wide event history configurationevent-history
Configure port-security event logsport-security
Configure port-security event logs for categorycategory
Configure port-security event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1288
E Commandsevent-history port-security category all
Page 1433
event-history port-security category fc2event-history port-security no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure port-security event logsport-security
Disable port-security event logs for categoryno
Configure port-security event logs for categorycategory
Configure port-security event logs for category FC2fc2
(Optional) Configure port-security event logs for FC2 Rx framesrx
(Optional) Configure brief port-security event logs for FC2 Rxbrief
(Optional) Configure detail port-security event logs for FC2 Rxdetail
(Optional) Configure port-security event logs for FC2 Tx framestx
(Optional) Configure brief port-security event logs for FC2 Txbrief1
(Optional) Configure detail port-security event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1289
E Commandsevent-history port-security category fc2
Page 1434
event-history port-security category fc2event-history port-security category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure port-security event logsport-security
Configure port-security event logs for categorycategory
Configure port-security event logs for category FC2fc2
(Optional) Configure port-security event logs for FC2 Rx framesrx
(Optional) Configure brief port-security event logs for FC2 Rxbrief
(Optional) Configure detail port-security event logs for FC2 Rxdetail
(Optional) Configure port-security event logs for FC2 Tx framestx
(Optional) Configure brief port-security event logs for FC2 Txbrief1
(Optional) Configure detail port-security event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1290
E Commandsevent-history port-security category fc2
Page 1435
event-history port-security category mtsevent-history port-security no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure port-security event logsport-security
Disable port-security event logs for categoryno
Configure port-security event logs for categorycategory
Configure port-security event logs for category mtsmts
(Optional) Configure port-security event logs for mts Rx framesrx
(Optional) Configure brief port-security event logs for mts Rxbrief
(Optional) Configure detail port-security event logs for mts Rxdetail
(Optional) Configure port-security event logs for mts Tx framestx
(Optional) Configure brief port-security event logs for mts Txbrief1
(Optional) Configure detail port-security event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1291
E Commandsevent-history port-security category mts
Page 1436
event-history port-security category mtsevent-history port-security category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure port-security event logsport-security
Configure port-security event logs for categorycategory
Configure port-security event logs for category mtsmts
(Optional) Configure port-security event logs for mts Rx framesrx
(Optional) Configure brief port-security event logs for mts Rxbrief
(Optional) Configure detail port-security event logs for mts Rxdetail
(Optional) Configure port-security event logs for mts Tx framestx
(Optional) Configure brief port-security event logs for mts Txbrief1
(Optional) Configure detail port-security event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1292
E Commandsevent-history port-security category mts
Page 1437
event-history port category fc2event-history port no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure port event logsport
Disable port event logs for categoryno
Configure port event logs for categorycategory
Configure port event logs for category FC2fc2
(Optional) Configure port event logs for FC2 Rx framesrx
(Optional) Configure brief port event logs for FC2 Rxbrief
(Optional) Configure detail port event logs for FC2 Rxdetail
(Optional) Configure port event logs for FC2 Tx framestx
(Optional) Configure brief port event logs for FC2 Txbrief1
(Optional) Configure detail port event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1293
E Commandsevent-history port category fc2
Page 1438
event-history port category fc2event-history port category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure port event logsport
Configure port event logs for categorycategory
Configure port event logs for category FC2fc2
(Optional) Configure port event logs for FC2 Rx framesrx
(Optional) Configure brief port event logs for FC2 Rxbrief
(Optional) Configure detail port event logs for FC2 Rxdetail
(Optional) Configure port event logs for FC2 Tx framestx
(Optional) Configure brief port event logs for FC2 Txbrief1
(Optional) Configure detail port event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1294
E Commandsevent-history port category fc2
Page 1439
event-history port category mtsevent-history port no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure port event logsport
Disable port event logs for categoryno
Configure port event logs for categorycategory
Configure port event logs for category mtsmts
(Optional) Configure port event logs for mts Rx framesrx
(Optional) Configure brief port event logs for mts Rxbrief
(Optional) Configure detail port event logs for mts Rxdetail
(Optional) Configure port event logs for mts Tx framestx
(Optional) Configure brief port event logs for mts Txbrief1
(Optional) Configure detail port event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1295
E Commandsevent-history port category mts
Page 1440
event-history port category mtsevent-history port category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure port event logsport
Configure port event logs for categorycategory
Configure port event logs for category mtsmts
(Optional) Configure port event logs for mts Rx framesrx
(Optional) Configure brief port event logs for mts Rxbrief
(Optional) Configure detail port event logs for mts Rxdetail
(Optional) Configure port event logs for mts Tx framestx
(Optional) Configure brief port event logs for mts Txbrief1
(Optional) Configure detail port event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1296
E Commandsevent-history port category mts
Page 1441
event-history port_client category allevent-history port_client no category all
Syntax Description
switch wide event history configurationevent-history
Configure port_client event logsport_client
Disable port_client event logs for categoryno
Configure port_client event logs for categorycategory
Configure port_client event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1297
E Commandsevent-history port_client category all
Page 1442
event-history port_client category allevent-history port_client category all
Syntax Description
switch wide event history configurationevent-history
Configure port_client event logsport_client
Configure port_client event logs for categorycategory
Configure port_client event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1298
E Commandsevent-history port_client category all
Page 1443
event-history port_client category fc2event-history port_client category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure port_client event logsport_client
Configure port_client event logs for categorycategory
Configure port_client event logs for category FC2fc2
(Optional) Configure port_client event logs for FC2 Rx framesrx
(Optional) Configure brief port_client event logs for FC2 Rxbrief
(Optional) Configure detail port_client event logs for FC2 Rxdetail
(Optional) Configure port_client event logs for FC2 Tx framestx
(Optional) Configure brief port_client event logs for FC2 Txbrief
(Optional) Configure detail port_client event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1299
E Commandsevent-history port_client category fc2
Page 1444
event-history port_client category fc2event-history port_client no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure port_client event logsport_client
Disable port_client event logs for categoryno
Configure port_client event logs for categorycategory
Configure port_client event logs for category FC2fc2
(Optional) Configure port_client event logs for FC2 Rx framesrx
(Optional) Configure brief port_client event logs for FC2 Rxbrief
(Optional) Configure detail port_client event logs for FC2 Rxdetail
(Optional) Configure port_client event logs for FC2 Tx framestx
(Optional) Configure brief port_client event logs for FC2 Txbrief
(Optional) Configure detail port_client event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1300
E Commandsevent-history port_client category fc2
Page 1445
event-history port_client category mtsevent-history port_client category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure port_client event logsport_client
Configure port_client event logs for categorycategory
Configure port_client event logs for category mtsmts
(Optional) Configure port_client event logs for mts Rx framesrx
(Optional) Configure brief port_client event logs for mts Rxbrief
(Optional) Configure detail port_client event logs for mts Rxdetail
(Optional) Configure port_client event logs for mts Tx framestx
(Optional) Configure brief port_client event logs for mts Txbrief
(Optional) Configure detail port_client event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1301
E Commandsevent-history port_client category mts
Page 1446
event-history port_client category mtsevent-history port_client no category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure port_client event logsport_client
Disable port_client event logs for categoryno
Configure port_client event logs for categorycategory
Configure port_client event logs for category mtsmts
(Optional) Configure port_client event logs for mts Rx framesrx
(Optional) Configure brief port_client event logs for mts Rxbrief
(Optional) Configure detail port_client event logs for mts Rxdetail
(Optional) Configure port_client event logs for mts Tx framestx
(Optional) Configure brief port_client event logs for mts Txbrief
(Optional) Configure detail port_client event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1302
E Commandsevent-history port_client category mts
Page 1447
event-history san-port-channel category allevent-history san-port-channel category all
Syntax Description
switch wide event history configurationevent-history
Configure pcm event logssan-port-channel
Configure pcm event logs for categorycategory
Configure pcm event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1303
E Commandsevent-history san-port-channel category all
Page 1448
event-history san-port-channel category allevent-history san-port-channel no category all
Syntax Description
switch wide event history configurationevent-history
Configure pcm event logssan-port-channel
Disable pcm event logs for categoryno
Configure pcm event logs for categorycategory
Configure pcm event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1304
E Commandsevent-history san-port-channel category all
Page 1449
event-history san-port-channel category fc2event-history san-port-channel category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure pcm event logssan-port-channel
Configure pcm event logs for categorycategory
Configure pcm event logs for category FC2fc2
(Optional) Configure pcm event logs for FC2 Rx framesrx
(Optional) Configure brief pcm event logs for FC2 Rxbrief
(Optional) Configure detail pcm event logs for FC2 Rxdetail
(Optional) Configure pcm event logs for FC2 Tx framestx
(Optional) Configure brief pcm event logs for FC2 Txbrief1
(Optional) Configure detail pcm event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1305
E Commandsevent-history san-port-channel category fc2
Page 1450
event-history san-port-channel category fc2event-history san-port-channel no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure pcm event logssan-port-channel
Disable pcm event logs for categoryno
Configure pcm event logs for categorycategory
Configure pcm event logs for category FC2fc2
(Optional) Configure pcm event logs for FC2 Rx framesrx
(Optional) Configure brief pcm event logs for FC2 Rxbrief
(Optional) Configure detail pcm event logs for FC2 Rxdetail
(Optional) Configure pcm event logs for FC2 Tx framestx
(Optional) Configure brief pcm event logs for FC2 Txbrief1
(Optional) Configure detail pcm event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1306
E Commandsevent-history san-port-channel category fc2
Page 1451
event-history san-port-channel category mtsevent-history san-port-channel category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure pcm event logssan-port-channel
Configure pcm event logs for categorycategory
Configure pcm event logs for category mtsmts
(Optional) Configure pcm event logs for mts Rx framesrx
(Optional) Configure brief pcm event logs for mts Rxbrief
(Optional) Configure detail pcm event logs for mts Rxdetail
(Optional) Configure pcm event logs for mts Tx framestx
(Optional) Configure brief pcm event logs for mts Txbrief1
(Optional) Configure detail pcm event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1307
E Commandsevent-history san-port-channel category mts
Page 1452
event-history san-port-channel category mtsevent-history san-port-channel no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure pcm event logssan-port-channel
Disable pcm event logs for categoryno
Configure pcm event logs for categorycategory
Configure pcm event logs for category mtsmts
(Optional) Configure pcm event logs for mts Rx framesrx
(Optional) Configure brief pcm event logs for mts Rxbrief
(Optional) Configure detail pcm event logs for mts Rxdetail
(Optional) Configure pcm event logs for mts Tx framestx
(Optional) Configure brief pcm event logs for mts Txbrief1
(Optional) Configure detail pcm event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1308
E Commandsevent-history san-port-channel category mts
Page 1453
event-history sensorevent-history sensor { category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ] } | no category{ all | mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ] } }
Syntax Description
switch wide event history configurationevent-history
Configure sensor USD event logssensor
Configure sensor USD event logs for categorycategory
Configure sensor USD event logs for category all eventsall
Configure sensor USD event logs for category mtsmts
(Optional) Configure sensor USD event logs for mts Rx framesrx
(Optional) Configure brief sensor USD event logs for mts Rxbrief
(Optional) Configure detail sensor USD event logs for mts Rxdetail
(Optional) Configure sensor USD event logs for mts Tx framestx
(Optional) Configure brief sensor USD event logs for mts Txbrief
(Optional) Configure detail sensor USD event logs for mts Txdetail
Disable sensor USD event logs for categoryno
Configure sensor USD event logs for categorycategory
Configure sensor USD event logs for category all eventsall
Configure sensor USD event logs for category mtsmts
(Optional) Configure sensor USD event logs for mts Rx framesrx
(Optional) Configure brief sensor USD event logs for mts Rxbrief
(Optional) Configure detail sensor USD event logs for mts Rxdetail
(Optional) Configure sensor USD event logs for mts Tx framestx
(Optional) Configure brief sensor USD event logs for mts Txbrief
(Optional) Configure detail sensor USD event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1309
E Commandsevent-history sensor
Page 1454
event-history session-mgr category allevent-history session-mgr no category all
Syntax Description
switch wide event history configurationevent-history
Configure session-mgr event logssession-mgr
Disable session-mgr event logs for categoryno
Configure session-mgr event logs for categorycategory
Configure session-mgr event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1310
E Commandsevent-history session-mgr category all
Page 1455
event-history session-mgr category allevent-history session-mgr category all
Syntax Description
switch wide event history configurationevent-history
Configure session-mgr event logssession-mgr
Configure session-mgr event logs for categorycategory
Configure session-mgr event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1311
E Commandsevent-history session-mgr category all
Page 1456
event-history session-mgr category mtsevent-history session-mgr no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure session-mgr event logssession-mgr
Disable session-mgr event logs for categoryno
Configure session-mgr event logs for categorycategory
Configure session-mgr event logs for category mtsmts
(Optional) Configure session-mgr event logs for mts Rx framesrx
(Optional) Configure brief session-mgr event logs for mts Rxbrief
(Optional) Configure detail session-mgr event logs for mts Rxdetail
(Optional) Configure session-mgr event logs for mts Tx framestx
(Optional) Configure brief session-mgr event logs for mts Txbrief1
(Optional) Configure detail session-mgr event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1312
E Commandsevent-history session-mgr category mts
Page 1457
event-history session-mgr category mtsevent-history session-mgr category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure session-mgr event logssession-mgr
Configure session-mgr event logs for categorycategory
Configure session-mgr event logs for category mtsmts
(Optional) Configure session-mgr event logs for mts Rx framesrx
(Optional) Configure brief session-mgr event logs for mts Rxbrief
(Optional) Configure detail session-mgr event logs for mts Rxdetail
(Optional) Configure session-mgr event logs for mts Tx framestx
(Optional) Configure brief session-mgr event logs for mts Txbrief1
(Optional) Configure detail session-mgr event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1313
E Commandsevent-history session-mgr category mts
Page 1458
event-history sflowevent-history sflow { category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ] } | no category{ all | mts [ { rx [ { brief1 | detail1 } ] | tx [ { brief2 | detail2 } ] } ] } }
Syntax Description
switch wide event history configurationevent-history
Configure sFlow event logssflow
Configure sFlow event logs for categorycategory
Configure sFlow event logs for category all eventsall
Configure sFlow event logs for category mtsmts
(Optional) Configure sFlow event logs for mts Rx framesrx
(Optional) Configure brief sFlow event logs for mts Rxbrief
(Optional) Configure detail sFlow event logs for mts Rxdetail
(Optional) Configure sFlow event logs for mts Tx framestx
(Optional) Configure brief sFlow event logs for mts Txbrief1
(Optional) Configure detail sFlow event logs for mts Txdetail1
Disable sFlow event logs for categoryno
Configure sFlow event logs for categorycategory
Configure sFlow event logs for category all eventsall
Configure sFlow event logs for category mtsmts
(Optional) Configure sFlow event logs for mts Rx framesrx
(Optional) Configure brief sFlow event logs for mts Rxbrief1
(Optional) Configure detail sFlow event logs for mts Rxdetail1
(Optional) Configure sFlow event logs for mts Tx framestx
(Optional) Configure brief sFlow event logs for mts Txbrief2
(Optional) Configure detail sFlow event logs for mts Txdetail2
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1314
E Commandsevent-history sflow
Page 1459
event-history snmpevent-history snmp { category { all | mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ] } | no category{ all | mts [ { rx [ { brief1 | detail1 } ] | tx [ { brief2 | detail2 } ] } ] } }
Syntax Description
switch wide event history configurationevent-history
Configure SNMP event logssnmp
Configure SNMP event logs for categorycategory
Configure SNMP event logs for category all eventsall
Configure snmp event logs for category MTSmts
(Optional) Configure snmp event logs for MTS Rx framesrx
(Optional) Configure brief SNMP event logs for MTS Rxbrief
(Optional) Configure detail SNMP event logs for MTS Rxdetail
(Optional) Configure SNMP event logs for MTS Tx framestx
(Optional) Configure brief SNMP event logs for MTS Txbrief1
(Optional) Configure detail snmp event logs for MTS Txdetail1
Disable SNMP event logs for categoryno
Configure SNMP event logs for categorycategory
Configure SNMP event logs for category all eventsall
Configure snmp event logs for category MTSmts
(Optional) Configure snmp event logs for MTS Rx framesrx
(Optional) Configure brief SNMP event logs for MTS Rxbrief1
(Optional) Configure detail SNMP event logs for MTS Rxdetail1
(Optional) Configure SNMP event logs for MTS Tx framestx
(Optional) Configure brief SNMP event logs for MTS Txbrief2
(Optional) Configure detail snmp event logs for MTS Txdetail2
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1315
E Commandsevent-history snmp
Page 1460
event-history spanning-tree category allevent-history spanning-tree category all
Syntax Description
switch wide event history configurationevent-history
Configure stp event logsspanning-tree
Configure stp event logs for categorycategory
Configure stp event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1316
E Commandsevent-history spanning-tree category all
Page 1461
event-history spm category allevent-history spm category all
Syntax Description
switch wide event history configurationevent-history
Configure spm event logsspm
Configure spm event logs for categorycategory
Configure spm event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1317
E Commandsevent-history spm category all
Page 1462
event-history spm category allevent-history spm no category all
Syntax Description
switch wide event history configurationevent-history
Configure spm event logsspm
Disable spm event logs for categoryno
Configure spm event logs for categorycategory
Configure spm event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1318
E Commandsevent-history spm category all
Page 1463
event-history spm category fc2event-history spm category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure spm event logsspm
Configure spm event logs for categorycategory
Configure spm event logs for category FC2fc2
(Optional) Configure spm event logs for FC2 Rx framesrx
(Optional) Configure brief spm event logs for FC2 Rxbrief
(Optional) Configure detail spm event logs for FC2 Rxdetail
(Optional) Configure spm event logs for FC2 Tx framestx
(Optional) Configure brief spm event logs for FC2 Txbrief1
(Optional) Configure detail spm event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1319
E Commandsevent-history spm category fc2
Page 1464
event-history spm category fc2event-history spm no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure spm event logsspm
Disable spm event logs for categoryno
Configure spm event logs for categorycategory
Configure spm event logs for category FC2fc2
(Optional) Configure spm event logs for FC2 Rx framesrx
(Optional) Configure brief spm event logs for FC2 Rxbrief
(Optional) Configure detail spm event logs for FC2 Rxdetail
(Optional) Configure spm event logs for FC2 Tx framestx
(Optional) Configure brief spm event logs for FC2 Txbrief1
(Optional) Configure detail spm event logs for FC2 Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1320
E Commandsevent-history spm category fc2
Page 1465
event-history spm category mtsevent-history spm no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure spm event logsspm
Disable spm event logs for categoryno
Configure spm event logs for categorycategory
Configure spm event logs for category mtsmts
(Optional) Configure spm event logs for mts Rx framesrx
(Optional) Configure brief spm event logs for mts Rxbrief
(Optional) Configure detail spm event logs for mts Rxdetail
(Optional) Configure spm event logs for mts Tx framestx
(Optional) Configure brief spm event logs for mts Txbrief1
(Optional) Configure detail spm event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1321
E Commandsevent-history spm category mts
Page 1466
event-history spm category mtsevent-history spm category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure spm event logsspm
Configure spm event logs for categorycategory
Configure spm event logs for category mtsmts
(Optional) Configure spm event logs for mts Rx framesrx
(Optional) Configure brief spm event logs for mts Rxbrief
(Optional) Configure detail spm event logs for mts Rxdetail
(Optional) Configure spm event logs for mts Tx framestx
(Optional) Configure brief spm event logs for mts Txbrief1
(Optional) Configure detail spm event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1322
E Commandsevent-history spm category mts
Page 1467
event-history stripcl category allevent-history stripcl no category all
Syntax Description
switch wide event history configurationevent-history
Configure stripcl event logsstripcl
Disable stripcl event logs for categoryno
Configure stripcl event logs for categorycategory
Configure stripcl event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1323
E Commandsevent-history stripcl category all
Page 1468
event-history stripcl category allevent-history stripcl category all
Syntax Description
switch wide event history configurationevent-history
Configure stripcl event logsstripcl
Configure stripcl event logs for categorycategory
Configure stripcl event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1324
E Commandsevent-history stripcl category all
Page 1469
event-history stripcl category mtsevent-history stripcl category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure stripcl event logsstripcl
Configure stripcl event logs for categorycategory
Configure stripcl event logs for category mtsmts
(Optional) Configure stripcl event logs for mts Rx framesrx
(Optional) Configure brief stripcl event logs for mts Rxbrief
(Optional) Configure detail stripcl event logs for mts Rxdetail
(Optional) Configure stripcl event logs for mts Tx framestx
(Optional) Configure brief stripcl event logs for mts Txbrief
(Optional) Configure detail stripcl event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1325
E Commandsevent-history stripcl category mts
Page 1470
event-history tamnw category allevent-history tamnw category all
Syntax Description
switch wide event history configurationevent-history
Configure tamnw event logstamnw
Configure tamnw event logs for categorycategory
Configure tamnw event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1326
E Commandsevent-history tamnw category all
Page 1471
event-history tamnw category allevent-history tamnw no category all
Syntax Description
switch wide event history configurationevent-history
Configure tamnw event logstamnw
Disable tamnw event logs for categoryno
Configure tamnw event logs for categorycategory
Configure tamnw event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1327
E Commandsevent-history tamnw category all
Page 1472
event-history tamnw category fc2event-history tamnw category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure tamnw event logstamnw
Configure tamnw event logs for categorycategory
Configure tamnw event logs for category FC2fc2
(Optional) Configure tamnw event logs for FC2 Rx framesrx
(Optional) Configure brief tamnw event logs for FC2 Rxbrief
(Optional) Configure detail tamnw event logs for FC2 Rxdetail
(Optional) Configure tamnw event logs for FC2 Tx framestx
(Optional) Configure brief tamnw event logs for FC2 Txbrief
(Optional) Configure detail tamnw event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1328
E Commandsevent-history tamnw category fc2
Page 1473
event-history tamnw category fc2event-history tamnw no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure tamnw event logstamnw
Disable tamnw event logs for categoryno
Configure tamnw event logs for categorycategory
Configure tamnw event logs for category FC2fc2
(Optional) Configure tamnw event logs for FC2 Rx framesrx
(Optional) Configure brief tamnw event logs for FC2 Rxbrief
(Optional) Configure detail tamnw event logs for FC2 Rxdetail
(Optional) Configure tamnw event logs for FC2 Tx framestx
(Optional) Configure brief tamnw event logs for FC2 Txbrief
(Optional) Configure detail tamnw event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1329
E Commandsevent-history tamnw category fc2
Page 1474
event-history tamnw category mtsevent-history tamnw no category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure tamnw event logstamnw
Disable tamnw event logs for categoryno
Configure tamnw event logs for categorycategory
Configure tamnw event logs for category mtsmts
(Optional) Configure tamnw event logs for mts Rx framesrx
(Optional) Configure brief tamnw event logs for mts Rxbrief
(Optional) Configure detail tamnw event logs for mts Rxdetail
(Optional) Configure tamnw event logs for mts Tx framestx
(Optional) Configure brief tamnw event logs for mts Txbrief
(Optional) Configure detail tamnw event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1330
E Commandsevent-history tamnw category mts
Page 1475
event-history tamnw category mtsevent-history tamnw category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure tamnw event logstamnw
Configure tamnw event logs for categorycategory
Configure tamnw event logs for category mtsmts
(Optional) Configure tamnw event logs for mts Rx framesrx
(Optional) Configure brief tamnw event logs for mts Rxbrief
(Optional) Configure detail tamnw event logs for mts Rxdetail
(Optional) Configure tamnw event logs for mts Tx framestx
(Optional) Configure brief tamnw event logs for mts Txbrief
(Optional) Configure detail tamnw event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1331
E Commandsevent-history tamnw category mts
Page 1476
event-history udld category allevent-history udld category all
Syntax Description
switch wide event history configurationevent-history
Configure udld event logsudld
Configure udld event logs for categorycategory
Configure udld event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1332
E Commandsevent-history udld category all
Page 1477
event-history ufdm category allevent-history ufdm category all
Syntax Description
switch wide event history configurationevent-history
Configure ufdm event logsufdm
Configure ufdm event logs for categorycategory
Configure ufdm event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1333
E Commandsevent-history ufdm category all
Page 1478
event-history ufdm category allevent-history ufdm no category all
Syntax Description
switch wide event history configurationevent-history
Configure ufdm event logsufdm
Disable ufdm event logs for categoryno
Configure ufdm event logs for categorycategory
Configure ufdm event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1334
E Commandsevent-history ufdm category all
Page 1479
event-history ufdm category fc2event-history ufdm no category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure ufdm event logsufdm
Disable ufdm event logs for categoryno
Configure ufdm event logs for categorycategory
Configure ufdm event logs for category FC2fc2
(Optional) Configure ufdm event logs for FC2 Rx framesrx
(Optional) Configure brief ufdm event logs for FC2 Rxbrief
(Optional) Configure detail ufdm event logs for FC2 Rxdetail
(Optional) Configure ufdm event logs for FC2 Tx framestx
(Optional) Configure brief ufdm event logs for FC2 Txbrief
(Optional) Configure detail ufdm event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1335
E Commandsevent-history ufdm category fc2
Page 1480
event-history ufdm category fc2event-history ufdm category fc2 [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure ufdm event logsufdm
Configure ufdm event logs for categorycategory
Configure ufdm event logs for category FC2fc2
(Optional) Configure ufdm event logs for FC2 Rx framesrx
(Optional) Configure brief ufdm event logs for FC2 Rxbrief
(Optional) Configure detail ufdm event logs for FC2 Rxdetail
(Optional) Configure ufdm event logs for FC2 Tx framestx
(Optional) Configure brief ufdm event logs for FC2 Txbrief
(Optional) Configure detail ufdm event logs for FC2 Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1336
E Commandsevent-history ufdm category fc2
Page 1481
event-history ufdm category mtsevent-history ufdm no category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure ufdm event logsufdm
Disable ufdm event logs for categoryno
Configure ufdm event logs for categorycategory
Configure ufdm event logs for category mtsmts
(Optional) Configure ufdm event logs for mts Rx framesrx
(Optional) Configure brief ufdm event logs for mts Rxbrief
(Optional) Configure detail ufdm event logs for mts Rxdetail
(Optional) Configure ufdm event logs for mts Tx framestx
(Optional) Configure brief ufdm event logs for mts Txbrief
(Optional) Configure detail ufdm event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1337
E Commandsevent-history ufdm category mts
Page 1482
event-history ufdm category mtsevent-history ufdm category mts [ { rx [ { brief | detail } ] | tx [ { brief | detail } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure ufdm event logsufdm
Configure ufdm event logs for categorycategory
Configure ufdm event logs for category mtsmts
(Optional) Configure ufdm event logs for mts Rx framesrx
(Optional) Configure brief ufdm event logs for mts Rxbrief
(Optional) Configure detail ufdm event logs for mts Rxdetail
(Optional) Configure ufdm event logs for mts Tx framestx
(Optional) Configure brief ufdm event logs for mts Txbrief
(Optional) Configure detail ufdm event logs for mts Txdetail
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1338
E Commandsevent-history ufdm category mts
Page 1483
event-history vdc category allevent-history vdc no category all
Syntax Description
switch wide event history configurationevent-history
Configure vdc_mgr event logsvdc
Disable vdc_mgr event logs for categoryno
Configure vdc_mgr event logs for categorycategory
Configure vdc_mgr event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1339
E Commandsevent-history vdc category all
Page 1484
event-history vdc category allevent-history vdc category all
Syntax Description
switch wide event history configurationevent-history
Configure vdc_mgr event logsvdc
Configure vdc_mgr event logs for categorycategory
Configure vdc_mgr event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1340
E Commandsevent-history vdc category all
Page 1485
event-history vdc category mtsevent-history vdc no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure vdc_mgr event logsvdc
Disable vdc_mgr event logs for categoryno
Configure vdc_mgr event logs for categorycategory
Configure vdc_mgr event logs for category mtsmts
(Optional) Configure vdc_mgr event logs for mts Rx framesrx
(Optional) Configure brief vdc_mgr event logs for mts Rxbrief
(Optional) Configure detail vdc_mgr event logs for mts Rxdetail
(Optional) Configure vdc_mgr event logs for mts Tx framestx
(Optional) Configure brief vdc_mgr event logs for mts Txbrief1
(Optional) Configure detail vdc_mgr event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1341
E Commandsevent-history vdc category mts
Page 1486
event-history xbar category allevent-history xbar no category all
Syntax Description
switch wide event history configurationevent-history
Configure xbar event logsxbar
Disable xbar event logs for categoryno
Configure xbar event logs for categorycategory
Configure xbar event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1342
E Commandsevent-history xbar category all
Page 1487
event-history xbar category allevent-history xbar category all
Syntax Description
switch wide event history configurationevent-history
Configure xbar event logsxbar
Configure xbar event logs for categorycategory
Configure xbar event logs for category all eventsall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1343
E Commandsevent-history xbar category all
Page 1488
event-history xbar category debugevent-history xbar no category debug { demux | deque | flow | ha | init }
Syntax Description
switch wide event history configurationevent-history
Configure xbar event logsxbar
Disable xbar event logs for categoryno
Configure xbar event logs for categorycategory
Configure xbar event logs for category debugdebug
Configure xbar event logs for category demuxdemux
Configure xbar event logs for category dequedeque
Configure xbar event logs for category flowflow
Configure xbar event logs for category HAha
Configure xbar event logs for category initinit
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1344
E Commandsevent-history xbar category debug
Page 1489
event-history xbar category debugevent-history xbar category debug { demux | deque | flow | ha | init }
Syntax Description
switch wide event history configurationevent-history
Configure xbar event logsxbar
Configure xbar event logs for categorycategory
Configure xbar event logs for category debugdebug
Configure xbar event logs for category demuxdemux
Configure xbar event logs for category dequedeque
Configure xbar event logs for category flowflow
Configure xbar event logs for category HAha
Configure xbar event logs for category initinit
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1345
E Commandsevent-history xbar category debug
Page 1490
event-history xbar category mtsevent-history xbar no category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure xbar event logsxbar
Disable xbar event logs for categoryno
Configure xbar event logs for categorycategory
Configure xbar event logs for category mtsmts
(Optional) Configure xbar event logs for mts Rx framesrx
(Optional) Configure brief xbar event logs for mts Rxbrief
(Optional) Configure detail xbar event logs for mts Rxdetail
(Optional) Configure xbar event logs for mts Tx framestx
(Optional) Configure brief xbar event logs for mts Txbrief1
(Optional) Configure detail xbar event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1346
E Commandsevent-history xbar category mts
Page 1491
event-history xbar category mtsevent-history xbar category mts [ { rx [ { brief | detail } ] | tx [ { brief1 | detail1 } ] } ]
Syntax Description
switch wide event history configurationevent-history
Configure xbar event logsxbar
Configure xbar event logs for categorycategory
Configure xbar event logs for category mtsmts
(Optional) Configure xbar event logs for mts Rx framesrx
(Optional) Configure brief xbar event logs for mts Rxbrief
(Optional) Configure detail xbar event logs for mts Rxdetail
(Optional) Configure xbar event logs for mts Tx framestx
(Optional) Configure brief xbar event logs for mts Txbrief1
(Optional) Configure detail xbar event logs for mts Txdetail1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1347
E Commandsevent-history xbar category mts
Page 1492
event-log-size{ { [ eigrp ] event-log-size <size> } | { no [ eigrp ] event-log-size [ <size> ] } }
Syntax Description
Negate a command or set its defaultsno
(Optional) EIGRP router configuration commandseigrp
Set IP-EIGRP event log sizeevent-log-size
Event log sizesize
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1348
E Commandsevent-log-size
Page 1493
event-logging[no] [ eigrp ] event-logging
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) EIGRP router configuration commandseigrp
Log IP-EIGRP routing eventsevent-logging
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1349
E Commandsevent-logging
Page 1494
event[no] event <eventname>
Syntax Description
Specify FTE Event to useevent
Name of eventeventname
Command Mode
• /exec/configure/config-fte-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1350
E Commandsevent
Page 1495
event[no] event
Syntax Description
Negate a command or set its defaultsno
Configure an event specificationevent
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1351
E Commandsevent
Page 1496
event application sub-system type[no] event application [ tag <tag_id> ] sub-system <sub-system-id> type <event-type>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Application specific eventapplication
(Optional) event tag identifiertag
(Optional) tag nametag_id
Sub-system ID that will publish the application eventsub-system
Sub-system ID valuesub-system-id
Event type within the specified sub-systemtype
Event type valueevent-type
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1352
E Commandsevent application sub-system type
Page 1497
event cli match[no] event cli [ tag <tag_id> ] match <regex> [ count <countnum> [ time <interval> ] ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create a cli event specificationcli
(Optional) event tag identifiertag
(Optional) tag nametag_id
Enter cli regex to be used for matchingmatch
CLI regex, use * to wildcard a tokenregex
(Optional) Enter an integer to be used as countcount
(Optional) Integer countcountnum
(Optional) Enter time interval within which the events need to happentime
(Optional) Time interval in seconds, 0 for indefinitelyinterval
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1353
E Commandsevent cli match
Page 1498
event counter name entry-val entry-op[no] event counter [ tag <tag_id> ] name <counter-name> entry-val <entry-val> entry-op <entry-op> [ exit-val<exit-val> exit-op <exit-op> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create a counter eventcounter
(Optional) event tag identifiertag
(Optional) tag nametag_id
Enter the name of the countername
Name of the countercounter-name
Specify the counter entry conditionsentry-val
Specify the value for comparison with the counter valueentry-val
Specify the operator to be used for comparisonentry-op
Specify the comparison operatorentry-op
(Optional) Specify the counter exit conditionsexit-val
(Optional) Specify the value for comparison with the counter valueexit-val
(Optional) Specify the operator to be used for comparisonexit-op
(Optional) Specify the comparison operatorexit-op
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1354
E Commandsevent counter name entry-val entry-op
Page 1499
event fanabsent time[no] event fanabsent [ fan <fan-number> ] time <time-interval>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create fanabsent event specificationfanabsent
(Optional) Optional. Enter fan number (optional arg)fan
(Optional) Enter fan-numberfan-number
Enter timetime
Time in seconds fan can stay absenttime-interval
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1355
E Commandsevent fanabsent time
Page 1500
event fanbad time[no] event fanbad [ fan <fan-number> ] time <time-interval>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create fanbad event specificationfanbad
(Optional) Optional. Enter fan number (optional arg)fan
(Optional) Enter fan-numberfan-number
Enter timetime
Time in seconds fan can stay badtime-interval
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1356
E Commandsevent fanbad time
Page 1501
event fib adjacency extra[no] event fib adjacency extra
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
FIB related eventfib
Adjacency related eventadjacency
Route extra in FIBextra
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1357
E Commandsevent fib adjacency extra
Page 1502
event fib resource tcam usage[no] event fib resource tcam usage
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
FIB related eventfib
Specify forwarding hardware resource related eventresource
Specify TCAM related eventtcam
Specify TCAM usage related eventusage
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1358
E Commandsevent fib resource tcam usage
Page 1503
event fib route[no] event fib route { inconsistent | missing | extra }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
FIB related eventfib
IP Route related eventroute
Inconsistent route in FIBinconsistent
Missing route in FIBmissing
Route extra in FIBextra
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1359
E Commandsevent fib route
Page 1504
event gold module test testing-type scheduledconsecutive-failure
event gold module { <module> | all } test { <name> } [ severity { minor | moderate | major } ] testing-type {scheduled | monitoring } consecutive-failure <cnt> | no event gold module { <module> | all } test { <name>}
Syntax Description
Negate a command or set its defaultsno
Configure an event specificationevent
Create a 'Diagnostic' event specificationgold
Module keywordmodule
Module Numbermodule
Select all module IDall
Diagnostic test selectiontest
Test namename
(Optional) Severity of failureseverity
(Optional) Minor failureminor
(Optional) Moderate failuremoderate
(Optional) Major failuremajor
Type of Diagnostic testtesting-type
Scheduled Testscheduled
Monitoring Testmonitoring
Consecutive number of times failure has occurredconsecutive-failure
Failure countcnt
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1360
E Commandsevent gold module test testing-type scheduled consecutive-failure
Page 1505
event manager applet[no] event manager applet <name> [ module <module-id> ] [ override <override-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Event Manager commandsevent
Event Manager commandsmanager
Create/Modify an Event Manager Policyapplet
Name of policy (cannot have underscore in first two characters)name
(Optional) Restrict policy to a modulemodule
(Optional)module-id
(Optional) Override a system policyoverride
(Optional) Name of the system policy to override - should begin withdouble underscore
override-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1361
E Commandsevent manager applet
Page 1506
event manager clear counterevent manager clear counter <counter-name>
Syntax Description
Event Manager commandsevent
Event Manager commandsmanager
Clear event manager informationclear
Clear the value of a countercounter
Name of the countercounter-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1362
E Commandsevent manager clear counter
Page 1507
event manager clear history eventsevent manager clear history events
Syntax Description
Event Manager commandsevent
Event Manager commandsmanager
Clear event manager informationclear
Clear the stored/archived informationhistory
Clear all the stored/archived event history for this VDCevents
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1363
E Commandsevent manager clear history events
Page 1508
event manager environmentevent manager environment <varname> <varvalue> | no event manager environment <varname>
Syntax Description
Negate a command or set its defaultsno
Event Manager commandsevent
Event Manager commandsmanager
Configure an environment variableenvironment
Name of the environment variablevarname
Value of the environment variablevarvalue
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1364
E Commandsevent manager environment
Page 1509
event manager policyevent manager policy <name>
Syntax Description
Event Manager commandsevent
Event Manager commandsmanager
Register a script policy and activate itpolicy
Name of the script policy filename
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1365
E Commandsevent manager policy
Page 1510
event manager runevent manager run <policy-name> [ <arg1> [ <arg2> [ <arg3> [ <arg4> [ <arg5> [ <arg6> [ <arg7> [ <arg8>[ <arg9> [ <arg10> ] ] ] ] ] ] ] ] ] ]
Syntax Description
Event Manager commandsevent
Event Manager commandsmanager
Trigger/run an event manager policy manuallyrun
Name of the policy to be triggered-cannot specify default system policypolicy-name
(Optional) User specified data value 1arg1
(Optional) User specified data value 2arg2
(Optional) User specified data value 3arg3
(Optional) User specified data value 4arg4
(Optional) User specified data value 5arg5
(Optional) User specified data value 6arg6
(Optional) User specified data value 7arg7
(Optional) User specified data value 8arg8
(Optional) User specified data value 9arg9
(Optional) User specified data value 10arg10
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1366
E Commandsevent manager run
Page 1511
event memory[no] event memory { minor | severe | critical }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create memory thresholds event specificationmemory
Minor alertminor
Severe alertsevere
Critical alertcritical
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1367
E Commandsevent memory
Page 1512
event module-failure type module count[no] event module-failure [ tag <tag_id> ] type <err-name> module { all | <module> } count <countnum> [time <interval> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create a 'module-failure' event specificationmodule-failure
(Optional) event tag identifiertag
(Optional) tag nametag_id
Enter an error typetype
err-name
Enter a module numbermodule
All modulesall
Enter module numbermodule
Enter an integer to be used as countcount
Integer countcountnum
(Optional) Enter time interval within which the events need to happentime
(Optional) Time interval in secondsinterval
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1368
E Commandsevent module-failure type module count
Page 1513
event module status module1[no] event module [ tag <tag_id> ] status { online | offline | any } module1 { all | <module> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create a 'module' event specificationmodule
(Optional) event tag identifiertag
(Optional) tag nametag_id
Status eventstatus
Online statusonline
Offline statusoffline
Online or offline statusany
Enter a module numbermodule1
All modulesall
Enter module numbermodule
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1369
E Commandsevent module status module1
Page 1514
event neighbor-discovery[no] event [ tag <tag_id> ] neighbor-discovery
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
(Optional) event tag identifiertag
(Optional) tag nametag_id
Show CDP new neighborsneighbor-discovery
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1370
E Commandsevent neighbor-discovery
Page 1515
event none[no] event none [ tag <tag_id> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Manually run policy event with nonenone
(Optional) event tag identifiertag
(Optional) tag nametag_id
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1371
E Commandsevent none
Page 1516
event oir fan[no] event oir [ tag <tag_id> ] fan { insert | remove | anyoir } [ <fannum> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create Online-Insertion-Removal event specificationoir
(Optional) event tag identifiertag
(Optional) tag nametag_id
Fan OIRfan
OIR insertinsert
OIR removeremove
any OIR (Either insert or remove)anyoir
(Optional) Optional. Enter Fan number.fannum
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1372
E Commandsevent oir fan
Page 1517
event oir module[no] event oir [ tag <tag_id> ] module { insert | remove | anyoir } [ <module> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create Online-Insertion-Removal event specificationoir
(Optional) event tag identifiertag
(Optional) tag nametag_id
Module OIRmodule
OIR insertinsert
OIR removeremove
any OIR (Either insert or remove)anyoir
(Optional) Optional. Enter module numbermodule
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1373
E Commandsevent oir module
Page 1518
event oir powersupply[no] event oir [ tag <tag_id> ] powersupply { insert | remove | anyoir } [ <powersupnum> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create Online-Insertion-Removal event specificationoir
(Optional) event tag identifiertag
(Optional) tag nametag_id
powersupply OIRpowersupply
OIR insertinsert
OIR removeremove
any OIR (Either insert or remove)anyoir
(Optional) Optional. Enter powersupply numberpowersupnum
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1374
E Commandsevent oir powersupply
Page 1519
event policy-default count[no] event policy-default count <countnum> [ time <interval> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Use the event in the system policy being overriddenpolicy-default
Enter an integer to be used as countcount
Integer countcountnum
(Optional) Enter time interval within which the events need to happentime
(Optional) Time interval in secondsinterval
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1375
E Commandsevent policy-default count
Page 1520
event poweroverbudget[no] event poweroverbudget
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create poweroverbudget event specificationpoweroverbudget
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1376
E Commandsevent poweroverbudget
Page 1521
event snmp oid get-type exact entry-op entry-val poll-interval[no] event snmp [ tag <tag_id> ] oid <oid-val> get-type { exact | next } entry-op { ent_gt | ent_ge | ent_eq |ent_ne | ent_lt | ent_le } entry-val <entry-val> [ { exit-comb { or | and } exit-op { ex_gt | ex_ge | ex_eq | ex_ne| ex_lt | ex_le } exit-val <exit-val> exit-time <exit-time-val> } | { exit-op1 { ex_gt1 | ex_ge1 | ex_eq1 | ex_ne1| ex_lt1 | ex_le1 } exit-val1 <exit-val1> } ] poll-interval <poll-int-val>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create a 'snmp' event specification.snmp
(Optional) event tag identifiertag
(Optional) tag nametag_id
oid of data element in dot notation.oid
oid of data element in dot notation.oid-val
The type of SNMP get operation.get-type
exactexact
nextnext
entry comparison operator.entry-op
greater thanent_gt
greater than or equal toent_ge
equal toent_eq
not equal toent_ne
less thanent_lt
less than or equal toent_le
value to compare with the current polled valueentry-val
value to compare with the current polled valueentry-val
(Optional) exit criterion combinationexit-comb
(Optional) logical ORor
(Optional) logical ANDand
(Optional) exit comparison operator.exit-op
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1377
E Commandsevent snmp oid get-type exact entry-op entry-val poll-interval
Page 1522
(Optional) greater thanex_gt
(Optional) greater than or equal toex_ge
(Optional) equal toex_eq
(Optional) not equal toex_ne
(Optional) less thanex_lt
(Optional) less than or equal toex_le
(Optional) value to compare with the current polled valueexit-val
(Optional) value to compare with the current polled valueexit-val
(Optional) exit comparison operator.exit-op1
(Optional) greater thanex_gt1
(Optional) greater than or equal toex_ge1
(Optional) equal toex_eq1
(Optional) not equal toex_ne1
(Optional) less thanex_lt1
(Optional) less than or equal toex_le1
(Optional) value to compare with the current polled valueexit-val1
(Optional) value to compare with the current polled valueexit-val1
(Optional) exit timeexit-time
(Optional) exit time in secondsexit-time-val
polling intervalpoll-interval
polling interval in secondspoll-int-val
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1378
E Commandsevent snmp oid get-type exact entry-op entry-val poll-interval
Page 1523
event storm-control[no] event storm-control
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create a storm control event specificationstorm-control
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1379
E Commandsevent storm-control
Page 1524
event syslog pattern[no] event syslog [ tag <tag_id> ] [ occurs <num-occurences> ] [ period <period-value> ] [ priority [ <i0> |alerts | critical | debugging | emergencies | errors | informational | notifications | warnings ] ] pattern <regex>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create a syslog event specificationsyslog
(Optional) event tag identifiertag
(Optional) tag nametag_id
(Optional) Enter an integer to be used for number of occurencesoccurs
(Optional) Integer countnum-occurences
(Optional) Enter time interval within which the events need to happenperiod
(Optional) Time interval in seconds, 0 for indefinitelyperiod-value
(Optional) Priority of the log messagepriority
(Optional) Enter priority of the log messagei0
(Optional) Alert log messagealerts
(Optional) Critical log messagecritical
(Optional) Debugging log messagedebugging
(Optional) Emergency log messageemergencies
(Optional) Error log messageerrors
(Optional) Informational log messageinformational
(Optional) Notifications log messagenotifications
(Optional) Warning log messagewarnings
Enter regex to be used for matchingpattern
SYSLOG regexregex
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1380
E Commandsevent syslog pattern
Page 1525
event sysmgr memory major minor clear[no] event sysmgr memory [ module <module> ] major <i0> minor <i1> clear <i2>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
system manager related eventssysmgr
memory alert eventmemory
(Optional) Optional. Enter module numbermodule
(Optional) Enter module-numbermodule
set major memory thresholdmajor
major memory thresholdi0
set minor memory thresholdminor
minor memory thresholdi1
set clear memory alert thresholdclear
clear memory thresholdi2
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1381
E Commandsevent sysmgr memory major minor clear
Page 1526
event sysmgr switchover count time[no] event sysmgr switchover count <countnum> time <interval>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
System manager related eventssysmgr
Switchover related eventswitchover
Number of switchovers after which event should be triggeredcount
Integer countcountnum
Enter time interval within which the events need to happentime
Time interval in secondsinterval
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1382
E Commandsevent sysmgr switchover count time
Page 1527
event temperature threshold[no] event temperature [ module <module> ] [ sensor <sensornum> ] threshold { major | minor | any }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create temperature event specificationtemperature
(Optional) Optional. Enter module number (optional arg)module
(Optional) Enter module-numbermodule
(Optional) Optional. Enter sensor number (optional arg)sensor
(Optional) Enter sensor numbersensornum
Enter Major or Minor thresholdthreshold
Major thresholdmajor
Minor thresholdminor
Major or Minorany
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1383
E Commandsevent temperature threshold
Page 1528
event test match[no] event test [ tag <tag_id> ] match <num> [ count <countnum> ] [ time <interval> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
(Optional) event tag identifiertag
(Optional) tag nametag_id
Create a 'test' event specificationtest
Enter an integer to be used for matchingmatch
Integer valuenum
(Optional) Enter an integer to be used as countcount
(Optional) Integer countcountnum
(Optional) <interval>time
(Optional) Time interval in secondsinterval
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1384
E Commandsevent test match
Page 1529
event timer[no] event timer [ tag <tag_id> ] { watchdog wtime <watchdog-time> | absolute atime <absolute-time> |countdown ctime <countdown-time> | cron cron-entry <cron-time> } [ name <timer_name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an event specificationevent
Create a timer event specificationtimer
(Optional) event tag identifiertag
(Optional) tag nametag_id
(Optional) name of the timername
(Optional) Enter the timer nametimer_name
Watchdog timer eventwatchdog
Time period for watchdogwtime
<1-1924991999[.0-999]> Enter seconds[.milliseconds] valuewatchdog-time
Absolute timer event.absolute
epoch time for absolute. Try epochconverter online tool to get valueatime
<1-1924991999[.0-999]> Enter seconds[.milliseconds] valueabsolute-time
Countdown timer eventcountdown
Time period for countdownctime
<1-1924991999[.0-999]> Enter seconds[.milliseconds] valuecountdown-time
Cron timer eventcron
Cron entry stringcron-entry
format: * * * * * => min hour dom month dowcron-time
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1385
E Commandsevent timer
Page 1530
event track stateevent track [ tag <tag_id> ] <object-id> state { any | up | down } | no event track [ tag <tag_id> ] <object-id>
Syntax Description
Negate a command or set its defaultsno
Configure an event specificationevent
Create a 'track' event specificationtrack
(Optional) event tag identifiertag
(Optional) tag nametag_id
Track objectsobject-id
State of tracking objectstate
Any stateany
Down statedown
Up stateup
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1386
E Commandsevent track state
Page 1531
evpn[no] evpn
Syntax Description
(Optional) Negate a command or set its defaultsno
Enter EVPN configuration modeevpn
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1387
E Commandsevpn
Page 1532
evpn esi multihoming[no] evpn esi multihoming
Syntax Description
(Optional) unconfigure the commandno
VxLAN evpn featureevpn
ESI based multihomingesi
Multihoming featuremultihoming
Command Mode
• /exec/configure/evpn-esi-multihoming
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1388
E Commandsevpn esi multihoming
Page 1533
evpn multihoming core-tracking[no] evpn multihoming core-tracking
Syntax Description
(Optional) Negate a command or set its defaultsno
VxLAN evpn featureevpn
VxLAN evpn multihomingmultihoming
core interface trackingcore-tracking
Command Mode
• /exec/configure/if-port-channel /exec/configure/if-routing /exec/configure/if-vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1389
E Commandsevpn multihoming core-tracking
Page 1534
evpn multisite border-gatewayevpn multisite border-gateway <site-id> | no evpn multisite border-gateway
Syntax Description
Unconfigure the commandno
EVPNevpn
Multisitemultisite
Border-gatewayborder-gateway
Multisite Site-Idsite-id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1390
E Commandsevpn multisite border-gateway
Page 1535
evpn multisite dci-tracking[no] evpn multisite dci-tracking
Syntax Description
(Optional) Negate a command or set its defaultsno
VxLAN evpn featureevpn
VxLAN evpn multisitemultisite
dci interface trackingdci-tracking
Command Mode
• /exec/configure/if-port-channel /exec/configure/if-routing /exec/configure/if-vlan/exec/configure/if-ethernet /exec/configure/if-range
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1391
E Commandsevpn multisite dci-tracking
Page 1536
evpn multisite fabric-tracking[no] evpn multisite fabric-tracking
Syntax Description
(Optional) Negate a command or set its defaultsno
VxLAN evpn featureevpn
VxLAN evpn multisitemultisite
fabric interface trackingfabric-tracking
Command Mode
• /exec/configure/if-port-channel /exec/configure/if-routing /exec/configure/if-vlan/exec/configure/if-ethernet /exec/configure/if-range
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1392
E Commandsevpn multisite fabric-tracking
Page 1537
evpn storm-control level[no] evpn storm-control { broadcast | multicast | unicast } level <lev>
Syntax Description
(Optional) Negate a command or set its defaultsno
VxLAN evpn featureevpn
Storm-controlstorm-control
Broadcast Packetsbroadcast
Multicast Packetsmulticast
Unknown Unicast Packetsunicast
Traffic levellevel
Enter the storm suppression levellev
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1393
E Commandsevpn storm-control level
Page 1538
exceptionlog module syserr devid errtype errcode phylayerports harderror
exceptionlog module <module> syserr <syserr> devid <id> errtype <type> errcode <code> phylayer <phy>ports <list> harderror <hard> [ { desc <str> } ] [ { inband <intinband> } ]
Syntax Description
Exception logexceptionlog
Enter a module numbermodule
Enter module numbermodule
Enter syserrsyserr
Syserr codesyserr
Enter device iddevid
Device idid
Enter error typeerrtype
Error typetype
Enter error codeerrcode
Error codecode
Enter phy layerphylayer
Phy layerphy
Enter failed portsports
List of portslist
Irrecoverable error?harderror
Error sub-categoryhard
(Optional) Enter error descriptiondesc
(Optional) Error descriptionstr
(Optional) inband flaginband
(Optional) inband flagintinband
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1394
E Commandsexceptionlog module syserr devid errtype errcode phylayer ports harderror
Page 1539
exclude access-list[no] exclude access-list <acl-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure access-list to exclude from redirectionexclude
PLB access-listaccess-list
Access-list nameacl-name
Command Mode
• /exec/configure/plb
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1395
E Commandsexclude access-list
Page 1540
exclude access-list[no] exclude access-list <acl-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
ACL to exclude from redirectionexclude
ITD access-list nameaccess-list
ITD exclude ACL nameacl-name
Command Mode
• /exec/configure/itd
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1396
E Commandsexclude access-list
Page 1541
exec-timeout{ exec-timeout <i0> | no exec-timeout [ <i0> ] }
Syntax Description
Negate a command or set its defaultsno
Configure exec timeoutexec-timeout
Enter timeout in minutes, 0 to disablei0
Command Mode
• /exec/configure/line
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1397
E Commandsexec-timeout
Page 1542
exec-timeout{ exec-timeout <i0> | no exec-timeout [ <i0> ] }
Syntax Description
Negate a command or set its defaultsno
Configure exec timeoutexec-timeout
Enter timeout in minutes, 0 to disablei0
Command Mode
• /exec/configure/console
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1398
E Commandsexec-timeout
Page 1543
existing-cli{ existing-cli <line> | no existing-cli <line> }
Syntax Description
Negate a command or set its defaultsno
Specify the existing cliexisting-cli
existing cli definition separated by <space> <semi-colon> <space>line
Command Mode
• /exec/configure/cli
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1399
E Commandsexisting-cli
Page 1544
exitexit
Syntax Description
Exit from command interpreterexit
Command Mode
• /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/tcp/exec/configure/ip-sla/icmpEcho /exec/configure/ip-sla/dns /exec/configure/ip-sla/fabricPathEcho/exec/configure/ip-sla/http
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1400
E Commandsexit
Page 1545
exitexit
Syntax Description
Exit from command interpreterexit
Command Mode
• /global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1401
E Commandsexit
Page 1546
exp[no] exp { default | <val> [ <val> [ <val> [ <val> [ <val> [ <val> [ <val> [ <val> ] ] ] ] ] ] ] [ default ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set the experimental values allowed for this interfaceexp
Default all unconfigured exp to this interfacedefault
Enter up to 8 experimental values separated by white-spacesval
Command Mode
• /exec/configure/tunnel-te/cbts-member
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1402
E Commandsexp
Page 1547
explicit-nullexplicit-null [ for <pfx-list> ] [ to <peer-pfx-list> ] | no explicit-null
Syntax Description
Negate a command or set its defaultsno
Advertise Explicit Null label in place of Implicit Nullexplicit-null
(Optional) Prefix list specifying controls on destination prefixesfor
(Optional) Name of prefix listpfx-list
(Optional) Access-list specifying controls on LDP peersto
(Optional) Name of prefix listpeer-pfx-list
Command Mode
• /exec/configure/ldp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1403
E Commandsexplicit-null
Page 1548
explicit-path[no] explicit-path <exp-path-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Preconfigured pathexplicit-path
Identifying name of the explicit-path with max 128 charactersexp-path-name
Command Mode
• /exec/configure/sr/te/pol/pref
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1404
E Commandsexplicit-path
Page 1549
explicit-path identifier[no] explicit-path { identifier <id> | name <string> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure explicit-pathexplicit-path
Specify explicit path by numberidentifier
Enter numberid
Specify explicit path by namename
Enter namestring
Command Mode
• /exec/configure/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1405
E Commandsexplicit-path identifier
Page 1550
export-gateway-ip[no] export-gateway-ip
Syntax Description
(Optional) Negate a command or set its defaultsno
Export Gateway IP to Type-5 EVPN routes for VRFexport-gateway-ip
Command Mode
• /exec/configure/router-bgp/router-bgp-vrf-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1406
E Commandsexport-gateway-ip
Page 1551
export map[no] export map <rmap-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
VRF exportexport
Route-map based VRF exportmap
Route-map namermap-name
Command Mode
• /exec/configure/vrf-af-ipv4 /exec/configure/vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1407
E Commandsexport map
Page 1552
export vrf default map[no] export vrf default [ <prefix-limit> ] map <rmap-name> [ allow-vpn ]
Syntax Description
(Optional) Negate a command or set its defaultsno
VRF exportexport
Virtual Router Contextvrf
VRF name (default)default
(Optional) Maximum prefix limitprefix-limit
Route-map based VRF importmap
Route-map namermap-name
(Optional) Allow re-importation of VPN imported routesallow-vpn
Command Mode
• /exec/configure/vrf-af-ipv4 /exec/configure/vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1408
E Commandsexport vrf default map
Page 1553
exporter-id{ [ no ] exporter-id <id> }
Syntax Description
Specify detailsexporter-id
exporter-id collectorid
Command Mode
• /exec/configure/config-fte-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1409
E Commandsexporter-id
Page 1554
exporter[no] exporter <exportername>
Syntax Description
Add an Exporter to use to export recordsexporter
Name of exporterexportername
Command Mode
• /exec/configure/config-int-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1410
E Commandsexporter
Page 1555
exporter[no] exporter <exportername>
Syntax Description
Add an Exporter to use to export recordsexporter
Name of exporterexportername
Command Mode
• /exec/configure/config-fte-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1411
E Commandsexporter
Page 1556
exporter[no] exporter <exportername> [ collector-bucket-id <cb-id> ]
Syntax Description
Add an Exporter to use to export recordsexporter
Name of exporterexportername
(Optional) Collector Bucket Idcollector-bucket-id
(Optional) Collector Bucket Idcb-id
Command Mode
• /exec/configure/nfm-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1412
E Commandsexporter
Page 1557
exporter[no] exporter <exportername>
Syntax Description
Exporter to be configuredexporter
Exporter to be configuredexportername
Command Mode
• /exec/configure/config-ssx-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1413
E Commandsexporter
Page 1558
exporter[no] exporter <exportername>
Syntax Description
Add an Exporter to use to export recordsexporter
Name of exporterexportername
Command Mode
• /exec/configure/config-postcard-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1414
E Commandsexporter
Page 1559
F Commands
• fabric-soo, on page 1420• fabric database auto-pull dci node-id, on page 1421• fabric database auto-pull dci vrf node-id, on page 1422• fabric database auto-pull vni interface, on page 1423• fabric database inherit-profile-map, on page 1424• fabric database mobility-domain, on page 1425• fabric database override-profile, on page 1426• fabric database override-vrf-profile, on page 1427• fabric database profile-map, on page 1428• fabric database profile-map global, on page 1429• fabric database refresh dot1q, on page 1430• fabric database refresh vni, on page 1431• fabric database static-host, on page 1432• fabric database timer, on page 1433• fabric database type bl-dci, on page 1434• fabric database type cabling, on page 1435• fabric database type host, on page 1436• fabric database type network, on page 1437• fabric database type partition, on page 1438• fabric database type profile, on page 1439• fabric forwarding admin-distance, on page 1440• fabric forwarding anycast-gateway-mac, on page 1441• fabric forwarding dup-host-ip-addr-detection, on page 1442• fabric forwarding dup-host-recovery-timer recover-count, on page 1443• fabric forwarding dup-host-unfreeze-timer unfreeze-count, on page 1444• fabric forwarding limit-vlan-mac, on page 1445• fabric forwarding mode anycast-gateway, on page 1446• fabric forwarding selective-host-probe, on page 1447• fabric multicast event-history bgp, on page 1448• fabric multicast event-history ha, on page 1449• fabric multicast event-history hmm, on page 1450• fabric multicast event-history isis, on page 1451• fabric multicast event-history m2rib, on page 1452
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1415
Page 1560
• fabric multicast event-history m6rib, on page 1453• fabric multicast event-history mrib, on page 1454• fabric multicast event-history pim, on page 1455• fabric multicast event-history pim6, on page 1456• failaction, on page 1457• failaction, on page 1458• fast-convergence, on page 1459• fast-convergence, on page 1460• fast-external-fallover, on page 1461• fast-flood enable, on page 1462• fast-flood enable, on page 1463• fast-flood enable, on page 1464• fast-flood interval, on page 1465• fast-flood interval, on page 1466• fast-flood interval, on page 1467• fast-reload, on page 1468• fast-reload network-os, on page 1469• fast-reroute, on page 1470• fast-reroute backup-prot-preempt optimize-bw, on page 1471• fcdroplatency network, on page 1472• fcoe, on page 1473• fcoe, on page 1474• fcoe enable-fex, on page 1475• fcoe fcf-priority, on page 1476• fcoe fcmap, on page 1477• fcoe fka-adv-period, on page 1478• fcoe veloopback, on page 1479• fcoe vsan, on page 1480• fctimer D_S_TOV, on page 1481• fctimer E_D_TOV, on page 1482• fctimer R_A_TOV, on page 1483• fctimer abort, on page 1484• fctimer commit, on page 1485• fctimer distribute, on page 1486• feature-set, on page 1487• feature-set, on page 1488• feature, on page 1489• feature analytics, on page 1490• feature bash-shell, on page 1491• feature bfd, on page 1492• feature bgp, on page 1493• feature catena, on page 1494• feature container-tracker, on page 1495• feature dhcp, on page 1496• feature dot1x, on page 1497• feature eigrp, on page 1498
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1416
F Commands
Page 1561
• feature evb, on page 1499• feature evmed, on page 1500• feature fabric forwarding, on page 1501• feature flexlink, on page 1502• feature grpc, on page 1503• feature hardware-telemetry, on page 1504• feature hsrp, on page 1505• feature icam, on page 1506• feature imp, on page 1507• feature interface-vlan, on page 1508• feature isis, on page 1509• feature itd, on page 1510• feature lacp, on page 1511• feature ldap, on page 1512• feature lldp, on page 1513• feature msdp, on page 1514• feature mvpn, on page 1515• feature nat, on page 1516• feature nbm, on page 1517• feature netconf, on page 1518• feature ngmvpn, on page 1519• feature ngoam, on page 1520• feature ngoam, on page 1521• feature npiv, on page 1522• feature ntp, on page 1523• feature nv overlay, on page 1524• feature nxapi, on page 1525• feature nxdb, on page 1526• feature nxsdk, on page 1527• feature openflow, on page 1528• feature openflow, on page 1529• feature ospf, on page 1530• feature ospfv3, on page 1531• feature password encryption aes, on page 1532• feature pbr, on page 1533• feature pim, on page 1534• feature pim6, on page 1535• feature plb, on page 1536• feature poap, on page 1537• feature poe, on page 1538• feature pong, on page 1539• feature port-security, on page 1540• feature private-vlan, on page 1541• feature privilege, on page 1542• feature ptp, on page 1543• feature restconf, on page 1544
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1417
F Commands
Page 1562
• feature rip, on page 1545• feature scheduler, on page 1546• feature scp-server, on page 1547• feature sflow, on page 1548• feature sftp-server, on page 1549• feature signature-verification, on page 1550• feature sla responder, on page 1551• feature sla sender, on page 1552• feature sla twamp-server, on page 1553• feature smart-channel, on page 1554• feature ssh, on page 1555• feature tacacs, on page 1556• feature telnet, on page 1557• feature tunnel, on page 1558• feature udld, on page 1559• feature vmtracker, on page 1560• feature vn-segment-vlan-based, on page 1561• feature vpc, on page 1562• feature vrrp, on page 1563• feature vrrpv3, on page 1564• feature vtp, on page 1565• fec, on page 1566• fec, on page 1567• fec, on page 1568• fhrp delay minimum, on page 1569• fhrp delay reload, on page 1570• filter, on page 1571• filter access-group, on page 1572• filter ip, on page 1573• filter ipv6 access-group, on page 1574• filter out, on page 1575• filter tx control-packets, on page 1576• filter vlan, on page 1577• filter vlan include-untagged, on page 1578• find, on page 1579• fips debug errors debug, on page 1580• fips mode enable, on page 1581• flow-count, on page 1582• flow-count, on page 1583• flow exporter, on page 1584• flow forward, on page 1585• flow monitor, on page 1586• flow record, on page 1587• flow timeout, on page 1588• flowcontrol hardware, on page 1589• flowcontrol receive, on page 1590
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1418
F Commands
Page 1563
• flush-routes, on page 1591• flush-routes, on page 1592• flush-routes, on page 1593• flush-routes, on page 1594• flush-routes, on page 1595• flush-routes, on page 1596• follow, on page 1597• format, on page 1598• format bootflash, on page 1599• format bootflash check-filesystem, on page 1600• format usb1, on page 1601• forward, on page 1602• forwarding-adjacency, on page 1603• fragments, on page 1604• frequency, on page 1605• from to, on page 1606• from to, on page 1607• fte event, on page 1608• fte exporter, on page 1609• fte monitor, on page 1610• fte record, on page 1611• fte system monitor, on page 1612• ftrace, on page 1613
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1419
F Commands
Page 1564
fabric-soo[no] fabric-soo { <ext-comm-soo-aa2nn4> | <ext-comm-soo-aa4nn2> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabric Site of Originfabric-soo
VPN extcommunity in aa4:fabric_id formatext-comm-soo-aa4nn2
VPN extcommunity in aa:fabric_id formatext-comm-soo-aa2nn4
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1420
F Commandsfabric-soo
Page 1565
fabric database auto-pull dci node-idfabric database auto-pull dci node-id <mgmt-ip-address>
Syntax Description
Fabricfabric
Fabric Databasedatabase
Pull configurationauto-pull
DCI profiledci
management ip address of this nodenode-id
IP address in CIDR formatmgmt-ip-address
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1421
F Commandsfabric database auto-pull dci node-id
Page 1566
fabric database auto-pull dci vrf node-idfabric database auto-pull dci vrf <vrf-name> node-id <mgmt-ip-address> [ peer-id <peer-ip-address> ]
Syntax Description
Fabricfabric
Fabric Databasedatabase
Pull configurationauto-pull
DCI profiledci
Display per-VRF informationvrf
VRF namevrf-name
management ip address of this nodenode-id
IP address in CIDR formatmgmt-ip-address
(Optional) management ip address of peerpeer-id
(Optional) IP address in CIDR formatpeer-ip-address
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1422
F Commandsfabric database auto-pull dci vrf node-id
Page 1567
fabric database auto-pull vni interfacefabric database auto-pull { vni <vni-id> | dot1q <vlan-id> } interface <interface-id> [ { overwrite-vlan |overwrite-bd } <ow-vlan-id> ]
Syntax Description
Fabricfabric
Fabric Databasedatabase
Pull configurationauto-pull
Pull ethernet-tag vni configurationvni
vni-id
Pull ethernet-tag dot1q configurationdot1q
vlan-id
Applied interfaceinterface
Name of interfaceinterface-id
(Optional) Overwrite the system generate vlanoverwrite-vlan
(Optional) Overwrite the system generate bdoverwrite-bd
(Optional)ow-vlan-id
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1423
F Commandsfabric database auto-pull vni interface
Page 1568
fabric database inherit-profile-map{ fabric database inherit-profile-map <id> } | { no fabric database inherit-profile-map }
Syntax Description
Negate a command or set its defaultsno
Fabricfabric
Configure Fabric Databasedatabase
Inherit a profile map. All non-global mappings will be inherited.inherit-profile-map
Profile Map IDid
Command Mode
• /exec/configure/if-eth-any /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1424
F Commandsfabric database inherit-profile-map
Page 1569
fabric database mobility-domain[no] fabric database mobility-domain <name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure Fabric Databasedatabase
Tag to identify mobility domain namemobility-domain
Mobility Domain Namename
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1425
F Commandsfabric database mobility-domain
Page 1570
fabric database override-profile[no] fabric database override-profile <profilename>
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure Fabric Databasedatabase
Override the network profile nameoverride-profile
Enter the profile name to override network profileprofilename
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1426
F Commandsfabric database override-profile
Page 1571
fabric database override-vrf-profile[no] fabric database override-vrf-profile <profilename>
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure Fabric Databasedatabase
Override the VRF (partition) profile nameoverride-vrf-profile
Enter the profile name to override VRF profileprofilename
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1427
F Commandsfabric database override-vrf-profile
Page 1572
fabric database profile-map[no] fabric database profile-map <id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure Fabric Databasedatabase
Configure a profile mapprofile-map
Profile Map IDid
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1428
F Commandsfabric database profile-map
Page 1573
fabric database profile-map global[no] fabric database profile-map global
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure Fabric Databasedatabase
Configure a profile mapprofile-map
Global profile (apply to all interfaces)global
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1429
F Commandsfabric database profile-map global
Page 1574
fabric database refresh dot1qfabric database refresh dot1q <vlan-id> [ { mobility-domain <name> | interface <interface-id> } ]
Syntax Description
Fabricfabric
Fabric Databasedatabase
Refresh profile configurationrefresh
Dot1Q Encapsulationdot1q
vlan-id
(Optional) Applied interfaceinterface
(Optional) Name of interfaceinterface-id
(Optional) Tag to identify mobility domain namemobility-domain
(Optional) Mobility Domain Namename
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1430
F Commandsfabric database refresh dot1q
Page 1575
fabric database refresh vnifabric database refresh { vni <vni-id> | include-vrf { <vrf-name> } }
Syntax Description
Fabricfabric
Fabric Databasedatabase
Refresh profile configurationrefresh
Virtual Network Identifiervni
vni-id
Include VRF nameinclude-vrf
VRF namevrf-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1431
F Commandsfabric database refresh vni
Page 1576
fabric database static-host[no] fabric database static-host
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Fabric Databasedatabase
Configure a static hoststatic-host
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1432
F Commandsfabric database static-host
Page 1577
fabric database timer[no] fabric database timer { aging | cleanup | recovery | re-add } <timeout>
Syntax Description
(Optional) Negate a command or set its defaultsno
fabric
database
HMM timerstimer
Delay in minutes before profile is deletedcleanup
Delay in minutes before recovered profile is deletedrecovery
Delay in minutes before new client requests (after un-apply) are acceptedre-add
Delay in minutes before profile is checked for agingaging
Set timeout in minutestimeout
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1433
F Commandsfabric database timer
Page 1578
fabric database type bl-dci[no] fabric database type bl-dci
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure Fabric Databasedatabase
Configure database typetype
Border Leaf - DCIbl-dci
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1434
F Commandsfabric database type bl-dci
Page 1579
fabric database type cabling[no] fabric database type cabling
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure Fabric Databasedatabase
Configure database typetype
Cable Management Databasecabling
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1435
F Commandsfabric database type cabling
Page 1580
fabric database type host[no] fabric database type host
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure Fabric Databasedatabase
Configure database typetype
Host Databasehost
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1436
F Commandsfabric database type host
Page 1581
fabric database type network[no] fabric database type network
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure Fabric Databasedatabase
Configure database typetype
Network Databasenetwork
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1437
F Commandsfabric database type network
Page 1582
fabric database type partition[no] fabric database type partition
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure Fabric Databasedatabase
Configure database typetype
Partition Databasepartition
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1438
F Commandsfabric database type partition
Page 1583
fabric database type profile[no] fabric database type profile
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure Fabric Databasedatabase
Configure database typetype
Port or Switch Profile Databaseprofile
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1439
F Commandsfabric database type profile
Page 1584
fabric forwarding admin-distance{ fabric forwarding admin-distance <distance> } | { no fabric forwarding admin-distance }
Syntax Description
Negate a command or set its defaultsno
Fabricfabric
Fabric Forwarding Protocol: Host Mobility Manager (HMM)forwarding
Administrative distance for HMM host routesadmin-distance
Set the administrative distance for HMM (default is 190)distance
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1440
F Commandsfabric forwarding admin-distance
Page 1585
fabric forwarding anycast-gateway-mac{ fabric forwarding anycast-gateway-mac <mac-addr> } | { no fabric forwarding anycast-gateway-mac }
Syntax Description
Negate a command or set its defaultsno
Fabricfabric
Fabric Forwarding Protocol: Host Mobility Manager (HMM)forwarding
Anycast Gateway MAC of the Switchanycast-gateway-mac
MAC addressmac-addr
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1441
F Commandsfabric forwarding anycast-gateway-mac
Page 1586
fabric forwarding dup-host-ip-addr-detection{ fabric forwarding dup-host-ip-addr-detection <mmoves> <nsecs> | no fabric forwardingdup-host-ip-addr-detection }
Syntax Description
Negate a command or set its defaultsno
Fabricfabric
Fabric Forwarding Protocol: Host Mobility Manager (HMM)forwarding
To detect duplicate host address in n secsdup-host-ip-addr-detection
Set Number of host moves to be allowed in n secs. Default is 5mmoves
Set the duplicate detection timeout in secs for host moves. Default is180
nsecs
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1442
F Commandsfabric forwarding dup-host-ip-addr-detection
Page 1587
fabric forwarding dup-host-recovery-timer recover-count{ fabric forwarding dup-host-recovery-timer <timeout> recover-count <count> | no fabric forwardingdup-host-recovery-timer }
Syntax Description
Negate a command or set its defaultsno
Fabricfabric
Fabric Forwarding Protocol: Host Mobility Manager (HMM)forwarding
Refresh the frozen duplicate hostdup-host-recovery-timer
Set the timeout in secs to refresh the duplicate host. Default is 30 secstimeout
Maximum number of refreshesrecover-count
Set the maximum number of host refresh. Default is 5.count
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1443
F Commandsfabric forwarding dup-host-recovery-timer recover-count
Page 1588
fabric forwarding dup-host-unfreeze-timer unfreeze-count{ fabric forwarding dup-host-unfreeze-timer <timeout> unfreeze-count <count> | no fabric forwardingdup-host-unfreeze-timer }
Syntax Description
Negate a command or set its defaultsno
Fabricfabric
Fabric Forwarding Protocol: Host Mobility Manager (HMM)forwarding
Refresh the frozen duplicate hostdup-host-unfreeze-timer
Set the timeout in secs to refresh the duplicate host. Default is 180 secstimeout
Maximum number of refreshesunfreeze-count
Set the maximum number of host refreshcount
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1444
F Commandsfabric forwarding dup-host-unfreeze-timer unfreeze-count
Page 1589
fabric forwarding limit-vlan-mac[no] fabric forwarding limit-vlan-mac <max-limit>
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Fabric Forwarding Protocol: Host Mobility Manager (HMM)forwarding
Maximum number of end-hosts allowed to have the same (vlan, MAC)mapping in a given vrf (Default is 2048)
limit-vlan-mac
Set max-limitmax-limit
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1445
F Commandsfabric forwarding limit-vlan-mac
Page 1590
fabric forwarding mode anycast-gateway{ fabric forwarding mode anycast-gateway } | { no fabric forwarding mode }
Syntax Description
Negate a command or set its defaultsno
Fabricfabric
Fabric Forwarding Protocol: Host Mobility Manager (HMM)forwarding
Forwarding Modesmode
Anycast Gateway Forwarding Modeanycast-gateway
Command Mode
• /exec/configure/if-vlan /exec/configure/if-vlan-range
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1446
F Commandsfabric forwarding mode anycast-gateway
Page 1591
fabric forwarding selective-host-probe[no] fabric forwarding selective-host-probe
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Fabric Forwarding Protocol: Host Mobility Manager (HMM)forwarding
Trigger unconditional host probeselective-host-probe
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1447
F Commandsfabric forwarding selective-host-probe
Page 1592
fabric multicast event-history bgp[no] fabric multicast event-history bgp { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure multicastmulticast
Configure event-history bufferevent-history
BGP events for fabric multicastbgp
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1448
F Commandsfabric multicast event-history bgp
Page 1593
fabric multicast event-history ha[no] fabric multicast event-history ha { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure multicastmulticast
Configure event-history bufferevent-history
ha events for fabric multicastha
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1449
F Commandsfabric multicast event-history ha
Page 1594
fabric multicast event-history hmm[no] fabric multicast event-history hmm { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure multicastmulticast
Configure event-history bufferevent-history
HMM events for fabric multicasthmm
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1450
F Commandsfabric multicast event-history hmm
Page 1595
fabric multicast event-history isis[no] fabric multicast event-history isis { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure multicastmulticast
Configure event-history bufferevent-history
ISIS events for fabric multicastisis
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1451
F Commandsfabric multicast event-history isis
Page 1596
fabric multicast event-history m2rib[no] fabric multicast event-history m2rib { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure multicastmulticast
Configure event-history bufferevent-history
M2RIB events for fabric multicastm2rib
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1452
F Commandsfabric multicast event-history m2rib
Page 1597
fabric multicast event-history m6rib[no] fabric multicast event-history m6rib { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure multicastmulticast
Configure event-history bufferevent-history
M6RIB events for fabric multicastm6rib
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1453
F Commandsfabric multicast event-history m6rib
Page 1598
fabric multicast event-history mrib[no] fabric multicast event-history mrib { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure multicastmulticast
Configure event-history bufferevent-history
MRIB events for fabric multicastmrib
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1454
F Commandsfabric multicast event-history mrib
Page 1599
fabric multicast event-history pim[no] fabric multicast event-history pim { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure multicastmulticast
Configure event-history bufferevent-history
PIM events for fabric multicastpim
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1455
F Commandsfabric multicast event-history pim
Page 1600
fabric multicast event-history pim6[no] fabric multicast event-history pim6 { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Fabricfabric
Configure multicastmulticast
Configure event-history bufferevent-history
PIM6 events for fabric multicastpim6
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1456
F Commandsfabric multicast event-history pim6
Page 1601
failaction[no] failaction { node { reassign | drop } | cluster drop } +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure failaction for PLB servicefailaction
PLB failaction nodenode
PLB failaction reassignreassign
PLB failaction dropdrop
PLB failaction clustercluster
Command Mode
• /exec/configure/plb
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1457
F Commandsfailaction
Page 1602
failaction[no] failaction { [ node { reassign | drop | least-bucket | per-bucket } ] | [ bucket { distribute } ] | [ cluster drop] }
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD failactionfailaction
(Optional) ITD failaction nodenode
(Optional) ITD failaction reassignreassign
(Optional) ITD failaction dropdrop
(Optional) ITD failaction least-bucket nodeleast-bucket
(Optional) ITD failaction per-bucket nodeper-bucket
(Optional) ITD failaction bucket reassignbucket
(Optional) ITD failaction distribute reassigndistribute
(Optional) ITD failaction clustercluster
Command Mode
• /exec/configure/itd
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1458
F Commandsfailaction
Page 1603
fast-convergence[no] fast-convergence
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure vPC fast convergencefast-convergence
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1459
F Commandsfast-convergence
Page 1604
fast-convergencefast-convergence | no fast-convergence
Syntax Description
Negate a command or set its defaultsno
Enable vPC fast-convergencefast-convergence
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1460
F Commandsfast-convergence
Page 1605
fast-external-fallover[no] fast-external-fallover
Syntax Description
(Optional) Negate a command or set its defaultsno
Immediately reset the session if the link to a directly connected BGPpeer goes down
fast-external-fallover
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1461
F Commandsfast-external-fallover
Page 1606
fast-flood enable[no] fast-flood enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Fast flood the LSP'sfast-flood
Turn on fast-floodingenable
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1462
F Commandsfast-flood enable
Page 1607
fast-flood enable[no] fast-flood enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Fast flood the LSP'sfast-flood
Turn on fast-floodingenable
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1463
F Commandsfast-flood enable
Page 1608
fast-flood enable[no] fast-flood enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Fast flood the LSP'sfast-flood
Turn on fast-floodingenable
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1464
F Commandsfast-flood enable
Page 1609
fast-flood interval[no] fast-flood interval <interval>
Syntax Description
(Optional) Negate a command or set its defaultsno
Fast flood the LSP'sfast-flood
Duration/interval of the fast-flood timer.interval
Specify the value (ms)interval
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1465
F Commandsfast-flood interval
Page 1610
fast-flood interval[no] fast-flood interval <interval>
Syntax Description
(Optional) Negate a command or set its defaultsno
Fast flood the LSP'sfast-flood
Duration/interval of the fast-flood timer.interval
Specify the value (ms)interval
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1466
F Commandsfast-flood interval
Page 1611
fast-flood interval[no] fast-flood interval <interval>
Syntax Description
(Optional) Negate a command or set its defaultsno
Fast flood the LSP'sfast-flood
Duration/interval of the fast-flood timer.interval
Specify the value (ms)interval
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1467
F Commandsfast-flood interval
Page 1612
fast-reloadfast-reload { [ nxos <uri> | trigger-gr | save-config | [ non-interruptive | nosrg ] ] + | force-all [ nxos <uri> ] +} [ override ]
Syntax Description
fast-reload softwarefast-reload
(Optional) boot-variable namenxos
(Optional) Enter image uriuri
(Optional) Non-Interruptive image upgradenon-interruptive
(Optional) nosrgnosrg
(Optional) Do fast-reload without impact checkoverride
(Optional) Enable BGP GR for compatible peerstrigger-gr
(Optional) Save running-config to startup-config before fast-reloadsave-config
Force upgrade the systemforce-all
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1468
F Commandsfast-reload
Page 1613
fast-reload network-osfast-reload network-os <uri>
Syntax Description
fast-reload softwarefast-reload
non-cisco OSnetwork-os
Enter image uriuri
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1469
F Commandsfast-reload network-os
Page 1614
fast-reroute[no] fast-reroute | fast-reroute [ node-protect | bw-protect ] +
Syntax Description
Negate a command or set its defaultsno
Specify mpls tunnel can be fast-reroutedfast-reroute
(Optional) node protection desirednode-protect
(Optional) bandwidth protection desiredbw-protect
Command Mode
• /exec/configure/if-te /exec/configure/tunnel-te/cbts-member
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1470
F Commandsfast-reroute
Page 1615
fast-reroute backup-prot-preempt optimize-bw[no] fast-reroute backup-prot-preempt optimize-bw | no fast-reroute timers promotion | fast-reroute timerspromotion <seconds>
Syntax Description
(Optional) Negate a command or set its defaultsno
fast-reroute parametersfast-reroute
Preemption algorithm for backup tunnelsbackup-prot-preempt
Reduce bandwidth wastage (default: minimize LSPs preempted)optimize-bw
configure fast-reroute timertimers
Configure how often we scan for LSP backup promotionpromotion
seconds between promotions (0 disables promotion.)seconds
Command Mode
• /exec/configure/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1471
F Commandsfast-reroute backup-prot-preempt optimize-bw
Page 1616
fcdroplatency network[no] fcdroplatency { network <i0> [ vsan <i1> ] | switch <i2> }
Syntax Description
(Optional) Negate a command or set its defaultsno
configure switch or network latencyfcdroplatency
network latency in millisecondsnetwork
network latency in millisecondsi0
(Optional) VSAN id rangevsan
(Optional)i1
switch latency in millisecondsswitch
switch latency in millisecondsi2
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1472
F Commandsfcdroplatency network
Page 1617
fcoe[no] fcoe
Syntax Description
(Optional) Negate a command or set its defaultno
FCOE Congigurationfcoe
Command Mode
• /exec/configure/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1473
F Commandsfcoe
Page 1618
fcoe[no] fcoe
Syntax Description
(Optional) Negate a command or set its defaultsno
create fcoe associate between fex and switchfcoe
Command Mode
• /exec/configure/fex
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1474
F Commandsfcoe
Page 1619
fcoe enable-fex[no] fcoe enable-fex
Syntax Description
(Optional) Negate a command or set its defaultsno
FCOE commandfcoe
Enables FCoE over FEX HIF interfacesenable-fex
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1475
F Commandsfcoe enable-fex
Page 1620
fcoe fcf-priorityfcoe fcf-priority <i0> | no fcoe fcf-priority
Syntax Description
Negate a command or set its defaultsno
FCOE commandfcoe
FCF priority specificationfcf-priority
Enter FCF prirorityi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1476
F Commandsfcoe fcf-priority
Page 1621
fcoe fcmapfcoe fcmap <i0> | no fcoe fcmap
Syntax Description
Negate a command or set its defaultsno
FCOE commandfcoe
FC MAP specificationfcmap
Enter FCMAPi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1477
F Commandsfcoe fcmap
Page 1622
fcoe fka-adv-periodfcoe fka-adv-period <i0> | no fcoe fka-adv-period
Syntax Description
Negate a command or set its defaultsno
FCOE commandfcoe
FKA Advertisement Periodfka-adv-period
FKA Advertisement Period (in sec)i0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1478
F Commandsfcoe fka-adv-period
Page 1623
fcoe veloopbackfcoe veloopback | no fcoe veloopback
Syntax Description
Negate a command or set its defaultsno
FCOE commandfcoe
VFID check for VE portsveloopback
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1479
F Commandsfcoe veloopback
Page 1624
fcoe vsanfcoe vsan <tran-id> | no fcoe vsan
Syntax Description
Negate a command or set its defaultno
FCOE Congigurationfcoe
Translated VSAN Statusvsan
Enter VSAN-ID being associated with VLAN-IDtran-id
Command Mode
• /exec/configure/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1480
F Commandsfcoe vsan
Page 1625
fctimer D_S_TOV[no] fctimer D_S_TOV <i0> [ vsan <i1> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
configure fibre channel timersfctimer
D_S_TOV in milliseconds(5000-10000)D_S_TOV
D_S_TOV in milliseconds(5000-10000)i0
(Optional) Specify VSAN idvsan
(Optional) VSAN idi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1481
F Commandsfctimer D_S_TOV
Page 1626
fctimer E_D_TOV[no] fctimer E_D_TOV <i0> [ vsan <i1> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
configure fibre channel timersfctimer
E_D_TOV in milliseconds(1000-4000)E_D_TOV
E_D_TOV in milliseconds(1000-4000)i0
(Optional) Specify VSAN idvsan
(Optional) VSAN idi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1482
F Commandsfctimer E_D_TOV
Page 1627
fctimer R_A_TOV[no] fctimer R_A_TOV <i0> [ vsan <i1> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
configure fibre channel timersfctimer
R_A_TOV in milliseconds(5000-10000)R_A_TOV
R_A_TOV in milliseconds(5000-10000)i0
(Optional) Specify VSAN idvsan
(Optional) VSAN idi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1483
F Commandsfctimer R_A_TOV
Page 1628
fctimer abort[no] fctimer abort
Syntax Description
(Optional) Negate a command or set its defaultsno
configure fibre channel timersfctimer
abort the fctimer configuration commandsabort
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1484
F Commandsfctimer abort
Page 1629
fctimer commit[no] fctimer commit
Syntax Description
(Optional) Negate a command or set its defaultsno
configure fibre channel timersfctimer
commit the fctimer configuration commandscommit
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1485
F Commandsfctimer commit
Page 1630
fctimer distribute[no] fctimer distribute
Syntax Description
(Optional) Negate a command or set its defaultsno
configure fibre channel timersfctimer
Enable distribution of fctimer configuration using CFSdistribute
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1486
F Commandsfctimer distribute
Page 1631
feature-setfeature-set <fs>
Syntax Description
Enable feature-setfeature-set
allow feature-setfs
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1487
F Commandsfeature-set
Page 1632
feature-set[no] feature-set <fs>
Syntax Description
Negate a command or set its defaultsno
Enable feature-setfeature-set
allow feature-setfs
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1488
F Commandsfeature-set
Page 1633
feature[no] feature <arg1>
Syntax Description
(Optional) Negate a command or set its defaultsno
Feature namefeature
Enter feature namearg1
Command Mode
• /exec/configure/rolefeaturegrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1489
F Commandsfeature
Page 1634
feature analytics[no] feature analytics
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Analytics!!!analytics
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1490
F Commandsfeature analytics
Page 1635
feature bash-shell[no] feature bash-shell
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable bash-shellbash-shell
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1491
F Commandsfeature bash-shell
Page 1636
feature bfd[no] feature bfd
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
bfdbfd
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1492
F Commandsfeature bfd
Page 1637
feature bgp[no] feature bgp
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Border Gateway Protocol (BGP)bgp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1493
F Commandsfeature bgp
Page 1638
feature catena[no] feature catena
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable catenacatena
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1494
F Commandsfeature catena
Page 1639
feature container-tracker[no] feature container-tracker
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable NXOS Container Trackercontainer-tracker
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1495
F Commandsfeature container-tracker
Page 1640
feature dhcp[no] feature dhcp
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable DHCP Managerdhcp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1496
F Commandsfeature dhcp
Page 1641
feature dot1x[no] feature dot1x
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable dot1xdot1x
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1497
F Commandsfeature dot1x
Page 1642
feature eigrp[no] feature eigrp
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1498
F Commandsfeature eigrp
Page 1643
feature evb[no] feature evb
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Edge Virtual Bridge (EVB)evb
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1499
F Commandsfeature evb
Page 1644
feature evmed[no] feature evmed
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Generic event detectorsevmed
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1500
F Commandsfeature evmed
Page 1645
feature fabric forwarding[no] feature fabric forwarding
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Fabric Servicesfabric
Enable/Disable Fabric Forwarding Protocol: Host Mobility Manager(HMM)
forwarding
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1501
F Commandsfeature fabric forwarding
Page 1646
feature flexlink[no] feature flexlink
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Flexlinkflexlink
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1502
F Commandsfeature flexlink
Page 1647
feature grpc[no] feature grpc
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable grpc Servicesgrpc
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1503
F Commandsfeature grpc
Page 1648
feature hardware-telemetry[no] feature hardware-telemetry
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Hardware Telemetryhardware-telemetry
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1504
F Commandsfeature hardware-telemetry
Page 1649
feature hsrp[no] feature hsrp
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Hot Standby Router Protocol (HSRP)hsrp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1505
F Commandsfeature hsrp
Page 1650
feature icam[no] feature icam
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable icamicam
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1506
F Commandsfeature icam
Page 1651
feature imp[no] feature imp
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable IMPimp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1507
F Commandsfeature imp
Page 1652
feature interface-vlan[no] feature interface-vlan
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable interface vlaninterface-vlan
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1508
F Commandsfeature interface-vlan
Page 1653
feature isis[no] feature isis
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable IS-IS Unicast Routing Protocol (IS-IS)isis
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1509
F Commandsfeature isis
Page 1654
feature itd[no] feature itd
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable ITDitd
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1510
F Commandsfeature itd
Page 1655
feature lacp[no] feature lacp
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable LACPlacp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1511
F Commandsfeature lacp
Page 1656
feature ldap[no] feature ldap
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable ldapldap
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1512
F Commandsfeature ldap
Page 1657
feature lldp[no] feature lldp
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable LLDPlldp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1513
F Commandsfeature lldp
Page 1658
feature msdp[no] feature msdp
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Multicast Source Discovery Protocol (MSDP)msdp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1514
F Commandsfeature msdp
Page 1659
feature mvpn[no] feature mvpn
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Multicast Virtual Private Networks.mvpn
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1515
F Commandsfeature mvpn
Page 1660
feature nat[no] feature nat
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable NATnat
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1516
F Commandsfeature nat
Page 1661
feature nbm[no] feature nbm
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable a featurefeature
Enable/Disable Non Blocking Multicast (NBM) featurenbm
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1517
F Commandsfeature nbm
Page 1662
feature netconf[no] feature netconf
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable netconf Servicesnetconf
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1518
F Commandsfeature netconf
Page 1663
feature ngmvpn[no] feature ngmvpn
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable EVPN/MVPN featuresngmvpn
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1519
F Commandsfeature ngmvpn
Page 1664
feature ngoam[no] feature ngoam
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable ngoamngoam
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1520
F Commandsfeature ngoam
Page 1665
feature ngoam[no] feature ngoam
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable ngoamngoam
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1521
F Commandsfeature ngoam
Page 1666
feature npiv[no] feature npiv
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1522
F Commandsfeature npiv
Page 1667
feature ntp[no] feature ntp
Syntax Description
(Optional) Negate a command or set its defaultno
Command to enable/disable featuresfeature
Enable/Disable NTPntp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1523
F Commandsfeature ntp
Page 1668
feature nv overlay[no] feature nv overlay
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable VxLANnv
Enable/Disable VxLANoverlay
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1524
F Commandsfeature nv overlay
Page 1669
feature nxapi[no] feature nxapi
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable nxapinxapi
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1525
F Commandsfeature nxapi
Page 1670
feature nxdb[no] feature nxdb
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable nxdbnxdb
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1526
F Commandsfeature nxdb
Page 1671
feature nxsdk[no] feature nxsdk
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable nxsdk Servicesnxsdk
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1527
F Commandsfeature nxsdk
Page 1672
feature openflow[no] feature openflow
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable OpenFlow agentopenflow
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1528
F Commandsfeature openflow
Page 1673
feature openflow[no] feature openflow
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable OpenFlow agentopenflow
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1529
F Commandsfeature openflow
Page 1674
feature ospf[no] feature ospf
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Open Shortest Path First Protocol (OSPF)ospf
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1530
F Commandsfeature ospf
Page 1675
feature ospfv3[no] feature ospfv3
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Open Shortest Path First Version 3 Protocol (OSPFv3)ospfv3
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1531
F Commandsfeature ospfv3
Page 1676
feature password encryption aes[no] feature password encryption aes
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable the featurefeature
Credential(s) for the user(s)/device(s)password
Strong encryption for credential(s)encryption
Encrypt using AES encryption standardaes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1532
F Commandsfeature password encryption aes
Page 1677
feature pbr[no] feature pbr
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Policy Based Routing(PBR)pbr
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1533
F Commandsfeature pbr
Page 1678
feature pim[no] feature pim
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Protocol Independent Multicast (PIM)pim
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1534
F Commandsfeature pim
Page 1679
feature pim6[no] feature pim6
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Protocol Independent Multicast(PIM) for IPv6pim6
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1535
F Commandsfeature pim6
Page 1680
feature plb[no] feature plb
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Pervasive Load Balancing featureplb
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1536
F Commandsfeature plb
Page 1681
feature poap[no] feature poap
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable POAPpoap
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1537
F Commandsfeature poap
Page 1682
feature poe[no] feature poe
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable a featurefeature
Enable/Disable Power over Ethernet(PoE) featurepoe
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1538
F Commandsfeature poe
Page 1683
feature pong[no] feature pong
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Pongpong
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1539
F Commandsfeature pong
Page 1684
feature port-security[no] feature port-security
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable eth port security featuresfeature
Enable/Disable port-securityport-security
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1540
F Commandsfeature port-security
Page 1685
feature private-vlan[no] feature private-vlan
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable private-vlanprivate-vlan
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1541
F Commandsfeature private-vlan
Page 1686
feature privilege[no] feature privilege
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable IOS type privilege level supportprivilege
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1542
F Commandsfeature privilege
Page 1687
feature ptp[no] feature ptp
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable PTPptp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1543
F Commandsfeature ptp
Page 1688
feature restconf[no] feature restconf
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable restconf Servicesrestconf
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1544
F Commandsfeature restconf
Page 1689
feature rip[no] feature rip
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Routing Information Protocol (RIP)rip
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1545
F Commandsfeature rip
Page 1690
feature scheduler[no] feature scheduler
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable schedulerscheduler
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1546
F Commandsfeature scheduler
Page 1691
feature scp-server[no] feature scp-server
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable SCP serverscp-server
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1547
F Commandsfeature scp-server
Page 1692
feature sflow[no] feature sflow
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable sFlow agentsflow
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1548
F Commandsfeature sflow
Page 1693
feature sftp-server[no] feature sftp-server
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable SFTP serversftp-server
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1549
F Commandsfeature sftp-server
Page 1694
feature signature-verification[no] feature signature-verification
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable image signature verificationsignature-verification
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1550
F Commandsfeature signature-verification
Page 1695
feature sla responder[no] feature sla responder
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable SLAsla
Enable/Disable responder part of SLAresponder
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1551
F Commandsfeature sla responder
Page 1696
feature sla sender[no] feature sla sender
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable SLAsla
Enable/Disable sender part of SLAsender
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1552
F Commandsfeature sla sender
Page 1697
feature sla twamp-server[no] feature sla twamp-server
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable SLAsla
Enable/Disable twamp-server part of SLAtwamp-server
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1553
F Commandsfeature sla twamp-server
Page 1698
feature smart-channel[no] feature smart-channel
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable smart-channelsmart-channel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1554
F Commandsfeature smart-channel
Page 1699
feature ssh[no] feature ssh
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable sshssh
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1555
F Commandsfeature ssh
Page 1700
feature tacacs[no] feature tacacs +
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1556
F Commandsfeature tacacs
Page 1701
feature telnet[no] feature telnet
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable telnettelnet
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1557
F Commandsfeature telnet
Page 1702
feature tunnel[no] feature tunnel
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Tunnel Managertunnel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1558
F Commandsfeature tunnel
Page 1703
feature udld[no] feature udld
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable UDLDudld
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1559
F Commandsfeature udld
Page 1704
feature vmtracker[no] feature vmtracker
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable VM Tracker featurevmtracker
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1560
F Commandsfeature vmtracker
Page 1705
feature vn-segment-vlan-based[no] feature vn-segment-vlan-based
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable VLAN based VN segmentvn-segment-vlan-based
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1561
F Commandsfeature vn-segment-vlan-based
Page 1706
feature vpc[no] feature vpc
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable VPC (Virtual Port Channel)vpc
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1562
F Commandsfeature vpc
Page 1707
feature vrrp[no] feature vrrp
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Virtual Router Redundancy Protocol (VRRP)vrrp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1563
F Commandsfeature vrrp
Page 1708
feature vrrpv3[no] feature vrrpv3
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable Virtual Router Redundancy Protocol (VRRP) version3
vrrpv3
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1564
F Commandsfeature vrrpv3
Page 1709
feature vtp[no] feature vtp
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresfeature
Enable/Disable VTPvtp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1565
F Commandsfeature vtp
Page 1710
fecfec <fec_val_old> | no fec [ <fec_val_old> ]
Syntax Description
Negate a command or set its defaultsno
Forwarding error correctionfec
Interface FEC optionsfec_val_old
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1566
F Commandsfec
Page 1711
fecfec <fec_val> | no fec [ <fec_val> ]
Syntax Description
Negate a command or set its defaultsno
Forwarding error correctionfec
Interface FEC optionsfec_val
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1567
F Commandsfec
Page 1712
fecfec <fec_val> | no fec [ <fec_val> ]
Syntax Description
Negate a command or set its defaultsno
Forwarding error correctionfec
Interface FEC optionsfec_val
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1568
F Commandsfec
Page 1713
fhrp delay minimum[no] fhrp delay minimum | fhrp delay minimum <delay>
Syntax Description
Negate a command or set its defaultsno
FHRP interface configuration commandsfhrp
Configure FHRP delaydelay
minimum delayminimum
Seconds to delaydelay
Command Mode
• /exec/configure/if-eth-any /exec/configure/if-vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1569
F Commandsfhrp delay minimum
Page 1714
fhrp delay reload[no] fhrp delay reload | fhrp delay reload <delay>
Syntax Description
Negate a command or set its defaultsno
FHRP interface configuration commandsfhrp
Configure FHRP delaydelay
reload delayreload
Seconds to delaydelay
Command Mode
• /exec/configure/if-eth-any /exec/configure/if-vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1570
F Commandsfhrp delay reload
Page 1715
filter[no] filter [ subject-name <s0> | altname-email <s1> | altname-upn <s2> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure mapping filterfilter
(Optional) Subject name of the certificatesubject-name
(Optional) Subject names0
(Optional) Email id as an alternate namealtname-email
(Optional) Email ids1
(Optional) User principal name as an alternate namealtname-upn
(Optional) User principal names2
Command Mode
• /exec/configure/certmap-filter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1571
F Commandsfilter
Page 1716
filter access-group[no] filter access-group <acl-name> [ allow-sharing ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Filter configurationfilter
access control groupaccess-group
access control list nameacl-name
(Optional) allow up to 4 access control groups on same source interfaceallow-sharing
Command Mode
• /exec/configure/monitor-local-src /exec/configure/config-monitor/exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1572
F Commandsfilter access-group
Page 1717
filter ip[no] filter ip <src_ip> <src_mask> <dst_ip> <dst_mask>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set SPAN filter optionsfilter
Set SPAN IP filtering optionsip
Set source IP addresssrc_ip
Set source IP masksrc_mask
Set destination IP addressdst_ip
Set destination IP maskdst_mask
Command Mode
• /exec/configure/monitor-local-src /exec/configure/config-monitor/exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1573
F Commandsfilter ip
Page 1718
filter ipv6 access-group[no] filter ipv6 access-group <acl-name> [ allow-sharing ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Filter configurationfilter
ipv6 access groupipv6
access control groupaccess-group
access control list nameacl-name
(Optional) allow up to 4 access control groups on same source interfaceallow-sharing
Command Mode
• /exec/configure/monitor-local-src /exec/configure/config-monitor/exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1574
F Commandsfilter ipv6 access-group
Page 1719
filter out[ no | default ] { filter-list <fltrlist-name> } { out | in }
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Apply AS-PATH filter-listfilter-list
Name of filter-listfltrlist-name
Apply policy to outgoing routesout
Apply policy to incoming routesin
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1575
F Commandsfilter out
Page 1720
filter tx control-packets[no] filter tx control-packets
Syntax Description
(Optional) Negate a command or set its defaultsno
Set SPAN filter optionsfilter
Set SPAN tx filtering optionstx
Filter out CPU generated packets and SPAN only data packetscontrol-packets
Command Mode
• /exec/configure/monitor-local-src /exec/configure/config-monitor/exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1576
F Commandsfilter tx control-packets
Page 1721
filter vlan[no] filter vlan <vlan_mrange> [ include-untagged ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Filter configurationfilter
Vlan typevlan
vlan_mrange
(Optional) Include untagged frames on port with Layer 3 subinterfacesinclude-untagged
Command Mode
• /exec/configure/monitor-local-src /exec/configure/config-monitor/exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1577
F Commandsfilter vlan
Page 1722
filter vlan include-untagged[no] filter vlan include-untagged
Syntax Description
(Optional) Negate a command or set its defaultsno
Filter configurationfilter
Vlan typevlan
Include untagged frames on port with Layer 3 subinterfacesinclude-untagged
Command Mode
• /exec/configure/config-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1578
F Commandsfilter vlan include-untagged
Page 1723
findfind <s0>
Syntax Description
Find a file below the current directoryfind
Enter the filename prefix to searchs0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1579
F Commandsfind
Page 1724
fips debug errors debug[no] fips debug errors { debug-lc-post-on-maint | reset-debug-lc-post-on-maint }
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/Disable FIPS modefips
Introduce errors into FIPS testsdebug
Introduce errorserrors
Run the switch on debug mode for fips maintenance statedebug-lc-post-on-maint
Reset the mode from debug-lc-post-on-maintreset-debug-lc-post-on-maint
Command Mode
• /exec/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1580
F Commandsfips debug errors debug
Page 1725
fips mode enable[no] fips mode enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/Disable FIPS modefips
FIPS modemode
Enable/Disable FIPS modeenable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1581
F Commandsfips mode enable
Page 1726
flow-count[no] flow-count <count>
Syntax Description
Flow count throttle for drop eventsflow-count
<1-32767>count
Command Mode
• /exec/configure/config-fte-event/group-drop-events
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1582
F Commandsflow-count
Page 1727
flow-count[no] flow-count <count>
Syntax Description
Flow count throttle for drop eventsflow-count
<1-32767>count
Command Mode
• /exec/configure/config-fte-event/group-latency-events
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1583
F Commandsflow-count
Page 1728
flow exporter[no] flow exporter <exportername>
Syntax Description
Enable/Disable NetFlow configurationflow
Define a Flow Exporterexporter
Name of Flow Exporterexportername
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1584
F Commandsflow exporter
Page 1729
flow forward[no] flow { forward | reverse }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure ngoam flowflow
Ngoam forward flowforward
Ngoam reverse flowreverse
Command Mode
• /exec/configure/configngoamprofile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1585
F Commandsflow forward
Page 1730
flow monitor[no] flow monitor <monitorname>
Syntax Description
Enable/Disable NetFlow configurationflow
Define a Flow Monitormonitor
Name of Flow Monitormonitorname
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1586
F Commandsflow monitor
Page 1731
flow record[no] flow record <recordname>
Syntax Description
Enable/Disable NetFlow configurationflow
Define a Flow Recordrecord
Record namerecordname
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1587
F Commandsflow record
Page 1732
flow timeout{ [ no ] flow timeout <time> | no flow timeout }
Syntax Description
Enable/Disable NetFlow configurationflow
Define a Flow Timeouttimeout
Time in seconds (flush-cache-Only)time
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1588
F Commandsflow timeout
Page 1733
flowcontrol hardware[no] flowcontrol hardware
Syntax Description
(Optional) Negate a command or set its defaultsno
Set flow controlflowcontrol
Set hardware flowcontrolhardware
Command Mode
• /exec/configure/com1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1589
F Commandsflowcontrol hardware
Page 1734
flowcontrol receiveflowcontrol { receive { <rx_flowctrl> } | send { <tx_flowctrl> } } | no flowcontrol { receive [ { <rx_flowctrl>} ] | send [ { <tx_flowctrl> } ] }
Syntax Description
Negate a command or set its defaultsno
Configure interface flowcontrolflowcontrol
Receive pause framesreceive
Receive flow controlrx_flowctrl
Send pause framessend
Send flow controltx_flowctrl
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1590
F Commandsflowcontrol receive
Page 1735
flush-routes[no] flush-routes
Syntax Description
(Optional) Negate a command or set its defaultsno
Flush routes on a non-graceful controlled restartflush-routes
Command Mode
• /exec/configure/router-ospf3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1591
F Commandsflush-routes
Page 1736
flush-routes[no] flush-routes
Syntax Description
(Optional) Negate a command or set its defaultsno
Flush routes in RIB during restartflush-routes
Command Mode
• /exec/configure/router-rip
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1592
F Commandsflush-routes
Page 1737
flush-routes[no] flush-routes
Syntax Description
(Optional) Negate a command or set its defaultsno
Flush routes on non-graceful controlled restartflush-routes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1593
F Commandsflush-routes
Page 1738
flush-routes[no] flush-routes
Syntax Description
(Optional) Negate a command or set its defaultsno
Flush routes in RIB during restartflush-routes
Command Mode
• /exec/configure/router-eigrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1594
F Commandsflush-routes
Page 1739
flush-routes[no] flush-routes
Syntax Description
(Optional) Negate a command or set its defaultsno
Flush routes on a non-graceful controlled restartflush-routes
Command Mode
• /exec/configure/router-ospf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1595
F Commandsflush-routes
Page 1740
flush-routes[no] flush-routes
Syntax Description
(Optional) Negate a command or set its defaultsno
Flush routes in RIB upon controlled restartflush-routes
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1596
F Commandsflush-routes
Page 1741
followfollow <name> | no follow
Syntax Description
Negate a command or set its defaultsno
Group to be followedfollow
master name string to followname
Command Mode
• /exec/configure/if-eth-any/hsrp_ipv4 /exec/configure/if-eth-any/hsrp_ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1597
F Commandsfollow
Page 1742
formatformat <uri1>
Syntax Description
Format disksformat
destination filesystem pathuri1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1598
F Commandsformat
Page 1743
format bootflashformat bootflash:
Syntax Description
Format disksformat
Format bootflash:bootflash:
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1599
F Commandsformat bootflash
Page 1744
format bootflash check-filesystemformat bootflash: check-filesystem
Syntax Description
Format disksformat
Format bootflash:bootflash:
Format bootflash: and fix any errors in file systemcheck-filesystem
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1600
F Commandsformat bootflash check-filesystem
Page 1745
format usb1format usb1:
Syntax Description
Format disksformat
Format usb1:usb1:
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1601
F Commandsformat usb1
Page 1746
forward[no] forward
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure pathsforward
Command Mode
• /exec/configure/mpls_static/ipv4/lsp/inlabel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1602
F Commandsforward
Page 1747
forwarding-adjacency[no] forwarding-adjacency | forwarding-adjacency [ holdtime <msec> ]
Syntax Description
Negate a command or set its defaultsno
Treat this tunnel as a Forwarding Adjacencyforwarding-adjacency
(Optional) How long in msecs to wait upon flooding a down ForwardingAdjacency
holdtime
(Optional) Holdtime on MPLS TE Downmsec
Command Mode
• /exec/configure/if-te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1603
F Commandsforwarding-adjacency
Page 1748
fragments[no] fragments <opt_type>
Syntax Description
(Optional) Negate a command or set its defaultsno
frag_op_typeopt_type
Command Mode
• /exec/configure/ipacl /exec/configure/ipv6acl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1604
F Commandsfragments
Page 1749
frequency{ { no | default } frequency | frequency <seconds> }
Syntax Description
no
Set a command to its defaultsdefault
Frequency of an operationfrequency
Frequency in secondsseconds
Command Mode
• /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/tcp/exec/configure/ip-sla/icmpEcho /exec/configure/ip-sla/dns /exec/configure/ip-sla/fabricPathEcho/exec/configure/ip-sla/http
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1605
F Commandsfrequency
Page 1750
from to[no] { { from <frm-list> to <to-val> } | { default { <value> | copy | ignore } } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Map values from thisfrom
Original list of values which are to be mappedfrm-list
Map values to thisto
New mapped valueto-val
map default valuesdefault
default value to be setvalue
Do a default copycopy
Ignore any unspecified valuesignore
Command Mode
• /exec/configure/table-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1606
F Commandsfrom to
Page 1751
from to{ [ no ] { { from <frm-list> to <to-val> } | { default <value> } } } | default copy
Syntax Description
(Optional) Negate a command or set its defaultsno
Map values from thisfrom
Original list of values which are to be mappedfrm-list
Map values to thisto
New mapped valueto-val
map default valuesdefault
default value to be setvalue
Do a default copycopy
Command Mode
• /exec/configure/def-tmap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1607
F Commandsfrom to
Page 1752
fte event[no] fte event <eventname>
Syntax Description
Enable/Disable FTE configurationfte
Define a FTE eventevent
Event nameeventname
Command Mode
• /exec/configure/config-fte
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1608
F Commandsfte event
Page 1753
fte exporter[no] fte exporter <exportername>
Syntax Description
Enable/Disable Flow Table Events configurationfte
Define a events Exporterexporter
Name of event Exporterexportername
Command Mode
• /exec/configure/config-fte
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1609
F Commandsfte exporter
Page 1754
fte monitor[no] fte monitor <monitorname>
Syntax Description
Enable/Disable FTE configurationfte
Define a FTE Monitormonitor
Name of FTE Monitormonitorname
Command Mode
• /exec/configure/config-fte
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1610
F Commandsfte monitor
Page 1755
fte record[no] fte record <recordname>
Syntax Description
Enable/Disable FTE configurationfte
Define a FTE Recordrecord
Record namerecordname
Command Mode
• /exec/configure/config-fte
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1611
F Commandsfte record
Page 1756
fte system monitor[no] fte system monitor <monitorname>
Syntax Description
change fte global settingsfte
global configsystem
fte Monitor to be appliedmonitor
ssx Monitor to be appliedmonitorname
Command Mode
• /exec/configure/config-fte
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1612
F Commandsfte system monitor
Page 1757
ftraceftrace [ { set-opt { option <n0> <v0> | filter <f0> <v0> } { proc <p0> | buf_size <b0> } [ <s0> ] } | { reset {all | filter <f0> | trace | <s0> } } | { enable { inband | kernel | lcnd <i0> | process <i0> | trace } } | { list { filters<f0> | curr_tracer | all } } | { debug { on | off } } | { dump { all | traces } } ]
Syntax Description
Run ftrace tool to enable/disable kernel/process tracingftrace
(Optional) Set ftrace tracing options availableset-opt
(Optional) Reset ftrace options to defaults, disable tracingreset
(Optional) Enable ftrace tracing with given optionsenable
(Optional) List ftrace available options/filters/eventslist
(Optional) Ftrace based debug trace enable/disabledebug
(Optional) Dump traces collected in ftrace circular bufferdump
(Optional) Act on all available datasetsall
(Optional) Trace proc/pid specific lcnd inband driver callslcnd
(Optional) Trace inband driver + netstack functionsinband
(Optional) Trace kernel function of sched, net, inbandkernel
(Optional) Trace proc/pid specific kernel function callsprocess
(Optional) Enable tracing_on in ftrace settingstrace
(Optional) Name of ftrace option to be setoption
(Optional) Set ftrace filter to be appliedfilter
(Optional) Set ftrace process to be tracedproc
(Optional) Set ftrace buffer size limitsbuf_size
(Optional) list available ftrace filtersfilters
(Optional) Print ftrace current tracercurr_tracer
(Optional) Dump ftrace trace buffer contentstraces
(Optional) Enable ftrace based debug tracingon
(Optional) Dump ftrace trace buffer contentsoff
(Optional) pid of process to tracei0
(Optional) name of ftrace filter to list/setf0
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1613
F Commandsftrace
Page 1758
(Optional) name of ftrace option to be setn0
(Optional) value of ftrace option/filter to be setv0
(Optional) pid of ftrace proc to be setp0
(Optional) value of ftrace buffer size limit to setb0
(Optional) name of ftrace option to be set/resets0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1614
F Commandsftrace
Page 1759
G Commands
• generate type7_encrypted_secret, on page 1616• getnext, on page 1617• global-block, on page 1618• global ingress-replication protocol bgp, on page 1619• global suppress-arp, on page 1620• graceful-restart-helper, on page 1621• graceful-restart, on page 1622• graceful-restart, on page 1623• graceful-restart, on page 1624• graceful-restart, on page 1625• graceful-restart, on page 1626• graceful-restart, on page 1627• graceful-restart, on page 1628• graceful-restart, on page 1629• graceful-restart grace-period, on page 1630• graceful-restart grace-period, on page 1631• graceful-restart helper-disable, on page 1632• graceful-restart helper-disable, on page 1633• graceful-restart restart-time, on page 1634• graceful-restart stalepath-time, on page 1635• graceful-restart t3 manual, on page 1636• graceful-restart t3 manual, on page 1637• graceful-restart t3 manual, on page 1638• graceful consistency-check, on page 1639• grep, on page 1640• grep, on page 1641• grep, on page 1642• group drop-events, on page 1643• group latency-events, on page 1644• guestshell, on page 1645• gunzip, on page 1646• gzip, on page 1647
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1615
Page 1760
generate type7_encrypted_secretgenerate type7_encrypted_secret
Syntax Description
generategenerate
Type 7 Encrypted Secrettype7_encrypted_secret
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1616
G Commandsgenerate type7_encrypted_secret
Page 1761
getnext| getnext
Syntax Description
Pipe command output to filter|
return next instance instead of specified one, or first instance if nonespecified (if supported by feature)
getnext
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1617
G Commandsgetnext
Page 1762
global-block{ { global-block <min-srgb-label> <max-srgb-label> } | { no global-block } }
Syntax Description
Negate a command or set its defaultsno
Specify global block range for Segment Routing bindingsglobal-block
Minimum label valuemin-srgb-label
Maximum label valuemax-srgb-label
Command Mode
• /exec/configure/config-sr-mpls
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1618
G Commandsglobal-block
Page 1763
global ingress-replication protocol bgp[no] global ingress-replication protocol bgp
Syntax Description
(Optional) Negate a command or set its defaultsno
Global configurations for nve, inherited by VNIsglobal
Configure ingress replicationingress-replication
Control protocol to useprotocol
Border Gateway Protocolbgp
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1619
G Commandsglobal ingress-replication protocol bgp
Page 1764
global suppress-arp[no] global suppress-arp
Syntax Description
(Optional) Negate a command or set its defaultsno
Global configurations for nve, inherited by VNIsglobal
Enable ARP suppressionsuppress-arp
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1620
G Commandsglobal suppress-arp
Page 1765
graceful-restart-helper[no] graceful-restart-helper
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Graceful Restart Helper mode functionalitygraceful-restart-helper
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1621
G Commandsgraceful-restart-helper
Page 1766
graceful-restart[no] graceful-restart
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable graceful restart for IS-ISgraceful-restart
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1622
G Commandsgraceful-restart
Page 1767
graceful-restart[no] graceful-restart
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable graceful restart for IS-ISgraceful-restart
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1623
G Commandsgraceful-restart
Page 1768
graceful-restart[no] graceful-restart [ planned-only ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure graceful restartgraceful-restart
(Optional) Enable graceful restart only for a planned restartplanned-only
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1624
G Commandsgraceful-restart
Page 1769
graceful-restart{ { [ no ] [ eigrp ] graceful-restart } | { [ no ] nsf } }
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) EIGRP router configuration commandseigrp
Peer resync without adjancency resetgraceful-restart
Non-stop forwardingnsf
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1625
G Commandsgraceful-restart
Page 1770
graceful-restart[no] graceful-restart [ planned-only ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure graceful restartgraceful-restart
(Optional) Enable graceful restart only for a planned restartplanned-only
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1626
G Commandsgraceful-restart
Page 1771
graceful-restartgraceful-restart [ timers { forwarding-holding <fwdg-holdtime> | max-recovery <recovery-time> |neighbor-liveness <peer-liveness-time> } ] | no graceful-restart [ timers { forwarding-holding | max-recovery| neighbor-liveness } ]
Syntax Description
Negate a command or set its defaultsno
Configure LDP Graceful Restartgraceful-restart
(Optional) Configure Graceful Restart timerstimers
(Optional) Forwarding State Holding timeforwarding-holding
(Optional) secondsfwdg-holdtime
(Optional) Max-Recovery timemax-recovery
(Optional) secondsrecovery-time
(Optional) Neighbor-Liveness timeneighbor-liveness
(Optional) secondspeer-liveness-time
Command Mode
• /exec/configure/ldp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1627
G Commandsgraceful-restart
Page 1772
graceful-restart[no] graceful-restart
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Graceful Restart functionalitygraceful-restart
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1628
G Commandsgraceful-restart
Page 1773
graceful-restart[no] graceful-restart
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable graceful restart for IS-ISgraceful-restart
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1629
G Commandsgraceful-restart
Page 1774
graceful-restart grace-period[no] graceful-restart grace-period <grace-period>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure graceful restartgraceful-restart
Configure maximum interval to restart gracefullygrace-period
Grace period in secondsgrace-period
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1630
G Commandsgraceful-restart grace-period
Page 1775
graceful-restart grace-period[no] graceful-restart grace-period <grace-period>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure graceful restartgraceful-restart
Configure maximum interval to restart gracefullygrace-period
Grace period in secondsgrace-period
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1631
G Commandsgraceful-restart grace-period
Page 1776
graceful-restart helper-disable[no] graceful-restart helper-disable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure graceful restartgraceful-restart
Disable helper modehelper-disable
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1632
G Commandsgraceful-restart helper-disable
Page 1777
graceful-restart helper-disable[no] graceful-restart helper-disable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure graceful restartgraceful-restart
Disable helper modehelper-disable
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1633
G Commandsgraceful-restart helper-disable
Page 1778
graceful-restart restart-timegraceful-restart restart-time <restart-time> | no graceful-restart restart-time [ <restart-time> ]
Syntax Description
Negate a command or set its defaultsno
Configure Graceful Restart functionalitygraceful-restart
Maximum time for restart advertised to peersrestart-time
Restart time (seconds)restart-time
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1634
G Commandsgraceful-restart restart-time
Page 1779
graceful-restart stalepath-timegraceful-restart stalepath-time <stalepath-time> | no graceful-restart stalepath-time [ <stalepath-time> ]
Syntax Description
Negate a command or set its defaultsno
Configure Graceful Restart functionalitygraceful-restart
Maximum time to keep a restarting peer's stale routesstalepath-time
Stalepath time (seconds)stalepath-time
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1635
G Commandsgraceful-restart stalepath-time
Page 1780
graceful-restart t3 manualgraceful-restart t3 manual <sec> | no graceful-restart t3 manual [ <sec> ]
Syntax Description
Negate a command or set its defaultsno
Enable graceful restart for IS-ISgraceful-restart
Set the T3 (RFC 3847) graceful restart timert3
Change manually T3 default valuemanual
Specify T3 value (secs)sec
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1636
G Commandsgraceful-restart t3 manual
Page 1781
graceful-restart t3 manualgraceful-restart t3 manual <sec> | no graceful-restart t3 manual [ <sec> ]
Syntax Description
Negate a command or set its defaultsno
Enable graceful restart for IS-ISgraceful-restart
Set the T3 (RFC 3847) graceful restart timert3
Change manually T3 default valuemanual
Specify T3 value (secs)sec
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1637
G Commandsgraceful-restart t3 manual
Page 1782
graceful-restart t3 manualgraceful-restart t3 manual <sec> | no graceful-restart t3 manual [ <sec> ]
Syntax Description
Negate a command or set its defaultsno
Enable graceful restart for IS-ISgraceful-restart
Set the T3 (RFC 3847) graceful restart timert3
Change manually T3 default valuemanual
Specify T3 value (secs)sec
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1638
G Commandsgraceful-restart t3 manual
Page 1783
graceful consistency-check[no] graceful consistency-check
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable graceful featuresgraceful
Enable graceful type-1 consistency checkconsistency-check
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1639
G Commandsgraceful consistency-check
Page 1784
grep| { grep | egrep } [ count | ignore-case | line-number | invert-match | word-exp | line-exp | <ctx> | next <num>| prev <num> ] + <expr>
Syntax Description
Pipe command output to filter|
Grep - print lines matching a patterngrep
Egrep - print lines matching a patternegrep
(Optional) Print a total count of matching lines onlycount
(Optional) Ignore case difference when comparing stringsignore-case
(Optional) Print each match preceded by its line numberline-number
(Optional) Print only lines that contain no matches for <expr>invert-match
(Optional) Print only lines where the match is a complete wordword-exp
(Optional) Print only lines where the match is a whole lineline-exp
(Optional) Print <num> lines of context on each side of every matchctx
(Optional) Print <num> lines of context after every matching linenext
(Optional) Print <num> lines of context before every matching lineprev
(Optional) Print <num> lines of contextnum
Search for the expressionexpr
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1640
G Commandsgrep
Page 1785
grep| { grep | egrep } [ -c | -i | -n | -v | -w | -x | <ctx> | -A <num> | -B <num> ] + <expr>
Syntax Description
Pipe command output to filter|
Grep - print lines matching a patterngrep
Egrep - print lines matching a patternegrep
(Optional) Print a total count of matching lines only-c
(Optional) Ignore case difference when comparing strings-i
(Optional) Print each match preceded by its line number-n
(Optional) Print only lines that contain no matches for <expr>-v
(Optional) Print only lines where the match is a complete word-w
(Optional) Print only lines where the match is a whole line-x
(Optional) Print <num> lines of context on each side of every matchctx
(Optional) Print <num> lines of context after every matching line-A
(Optional) Print <num> lines of context before every matching line-B
(Optional) Print <num> lines of contextnum
Search for the expressionexpr
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1641
G Commandsgrep
Page 1786
grep| { grep | egrep } [ -c | -i | -n | -v | -w | -x | <ctx> | -A <num> | -B <num> ] + [ -- ] <expr>
Syntax Description
Pipe command output to filter|
Grepgrep
Egrepegrep
(Optional) Print a total count of matching lines only-c
(Optional) Ignore case difference when comparing strings-i
(Optional) Print each match preceded by its line number-n
(Optional) Print only lines that contain no matches for <expr>-v
(Optional) Print only lines where the match is a complete word-w
(Optional) Print only lines where the match is a whole line-x
(Optional) Print <num> lines of context on each side of every matchctx
(Optional) Print <num> lines of context after every matching line-A
(Optional) Print <num> lines of context before every matching line-B
(Optional) Print <num> lines of contextnum
(Optional) ----
Search for the expressionexpr
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1642
G Commandsgrep
Page 1787
group drop-events[no] group drop-events
Syntax Description
Group for which the events need to be setgroup
Set events for dropsdrop-events
Command Mode
• /exec/configure/config-fte-event
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1643
G Commandsgroup drop-events
Page 1788
group latency-events[no] group latency-events
Syntax Description
Group for which the events need to be setgroup
Set events for latency eventslatency-events
Command Mode
• /exec/configure/config-fte-event
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1644
G Commandsgroup latency-events
Page 1789
guestshellguestshell [ { enable [ { package <enable_uri> } ] } | { upgrade [ { package <upgrade_uri> } ] } | { export {rootfs package <export_uri> } } | { disable } | { destroy } | { reboot } | <sync_cmd_name> | { resize { rootfs<gsh_rootfs> | cpu <gsh_cpu> | memory <gsh_memory> } } | { run { <cmd_args> } } ]
Syntax Description
Request a guest shellguestshell
(Optional) Enable the guest shell serviceenable
(Optional) Upgrade the guest shell service package to a different versionupgrade
(Optional) Export the guest shellexport
(Optional) Destination file or directory pathexport_uri
(Optional) Disable the guest shell service packagedisable
(Optional) Disable and uninstall the guest shell service packagedestroy
(Optional) Synchronize the contents of the guest shell to standbysupervisor
sync_cmd_name
(Optional) Deactivate and reactivate the guest shell servicereboot
(Optional) Resize the existing/default guest shell parametersresize
(Optional) Guest shell root filesystem disk imagerootfs
(Optional) New root filesystem size (in MB)gsh_rootfs
(Optional) System CPU share allocated to guest shellcpu
(Optional) New CPU share allocation (as % of system CPU)gsh_cpu
(Optional) System memory allocated to guest shellmemory
(Optional) New memory size (in MB)gsh_memory
(Optional) Package locationpackage
(Optional) File name for the virtual serviceenable_uri
(Optional) File name for the virtual serviceupgrade_uri
(Optional) Execute/run program in the guest shellrun
(Optional) Executable with optional argumentscmd_args
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1645
G Commandsguestshell
Page 1790
gunzipgunzip <uri0>
Syntax Description
Uncompresses LZ77 coded filesgunzip
Enter filename (filename must have .gz extension)uri0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1646
G Commandsgunzip
Page 1791
gzipgzip <uri0>
Syntax Description
Compresses file using LZ77 codinggzip
Enter filenameuri0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1647
G Commandsgzip
Page 1792
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1648
G Commandsgzip
Page 1793
H Commands
• ha-policy single, on page 1652• hardware-telemetry fte, on page 1653• hardware-telemetry inband-telemetry, on page 1654• hardware-telemetry postcard-telemetry, on page 1655• hardware-telemetry ssx, on page 1656• hardware access-list lou resource threshold, on page 1657• hardware access-list match inner-header, on page 1658• hardware access-list module, on page 1659• hardware access-list tcam label ing-racl 9, on page 1660• hardware access-list tcam region, on page 1661• hardware access-list tcam region double-wide, on page 1662• hardware access-list tcam region qualify udf, on page 1663• hardware access-list tcam region tcp-nat, on page 1664• hardware ecmp hash-offset, on page 1665• hardware ecmp hash-polynomial, on page 1666• hardware ejector enable, on page 1667• hardware fan-zone raise-speed, on page 1668• hardware forwarding l3 resource route non-deterministic, on page 1669• hardware forwarding unicast trace, on page 1670• hardware ip glean throttle, on page 1671• hardware ip glean throttle maximum, on page 1672• hardware ip glean throttle syslog, on page 1673• hardware ip glean throttle timeout, on page 1674• hardware ipv6 glean throttle, on page 1675• hardware ipv6 glean throttle maximum, on page 1676• hardware ipv6 glean throttle syslog, on page 1677• hardware ipv6 glean throttle timeout, on page 1678• hardware module boot-order reverse, on page 1679• hardware multicast global-tx-span, on page 1680• hardware profile buffer info poll-interval timer, on page 1681• hardware profile buffer info port-threshold threshold, on page 1682• hardware profile buffer monitor unicast, on page 1683• hardware profile buffer qosgroup threshold, on page 1684
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1649
Page 1794
• hardware profile buffer span-threshold, on page 1685• hardware profile ecmp auto-recovery threshold, on page 1686• hardware profile ecmp resilient, on page 1687• hardware profile ecmp template module, on page 1688• hardware profile forwarding-mode, on page 1689• hardware profile front portmode, on page 1690• hardware profile ipv6 alpm carve-value, on page 1691• hardware profile ipv6 lpm-entries maximum, on page 1692• hardware profile latency monitor, on page 1693• hardware profile module, on page 1694• hardware profile multicast flex-stats-enable, on page 1695• hardware profile multicast max-limit, on page 1696• hardware profile multicast max-limit lpm-entries, on page 1697• hardware profile multicast nlb, on page 1698• hardware profile multicast optimization disable, on page 1699• hardware profile multicast prefer-source-tree, on page 1700• hardware profile multicast rpf-check-optimization, on page 1701• hardware profile multicast service-reflect port, on page 1702• hardware profile multicast slow-receiver port, on page 1703• hardware profile multicast syslog-threshold, on page 1704• hardware profile openflow, on page 1705• hardware profile packet-drop, on page 1706• hardware profile pbr skip-selfip, on page 1707• hardware profile pfc mmu buffer-reservation, on page 1708• hardware profile portmode, on page 1709• hardware profile statistics pstat, on page 1710• hardware profile svi flex-stats-enable, on page 1711• hardware profile tcam ipv6-sup-tcam match-inner, on page 1712• hardware profile tcam region, on page 1713• hardware profile tcam region span qualify udf, on page 1714• hardware profile tcam region spanv6-l2 qualify udf, on page 1715• hardware profile tcam region spanv6 qualify udf, on page 1716• hardware profile tcam resource service-template, on page 1717• hardware profile tcam resource template, on page 1718• hardware profile tcam syslog-threshold, on page 1719• hardware profile ucast6 lpm-65-to-127-max-limit, on page 1720• hardware profile ucast6 max-limit, on page 1721• hardware profile unicast enable-host-ecmp, on page 1722• hardware profile unicast syslog-threshold, on page 1723• hardware qos dynamic-buffer-sharing, on page 1724• hardware qos fc rate-shaper, on page 1725• hardware qos pfc mc-drop, on page 1726• hardware sample-redirect module redirect-interface, on page 1727• head, on page 1728• header-type 2, on page 1729• hello-interval, on page 1730
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1650
H Commands
Page 1795
• hello-interval, on page 1731• hello-interval, on page 1732• history, on page 1733• history, on page 1734• history, on page 1735• history, on page 1736• history, on page 1737• history, on page 1738• holdtime, on page 1739• hop-limit maximum, on page 1740• hop-limit minimum, on page 1741• hop, on page 1742• host-reachability protocol, on page 1743• host, on page 1744• host group permit, on page 1745• host source group permit, on page 1746• hostname, on page 1747• hostname dynamic, on page 1748• hostname dynamic, on page 1749• hostname dynamic, on page 1750• hsrp, on page 1751• hsrp anycast, on page 1752• hsrp bfd, on page 1753• hsrp bfd all-interfaces, on page 1754• hsrp delay minimum, on page 1755• hsrp force state vlan, on page 1756• hsrp ipv6, on page 1757• hsrp mac-refresh, on page 1758• hsrp timers extended-hold, on page 1759• hsrp use-bia, on page 1760• hsrp version 1, on page 1761• http get, on page 1762• http proxy server, on page 1763• human, on page 1764• human, on page 1765• hw-module logging onboard, on page 1766• hw-module logging onboard, on page 1767
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1651
H Commands
Page 1796
ha-policy singleha-policy { single-sup <hap-change> | dual-sup <sw-change> } +
Syntax Description
Change HA policy for this VDCha-policy
Change HA policy for this VDChap-change
Change HA policy for this VDC for single-sup situationssingle-sup
Change HA policy for this VDC for dual-sup situationsdual-sup
Set hap policysw-change
Command Mode
• /exec/configure/vdc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1652
H Commandsha-policy single
Page 1797
hardware-telemetry fte[no] hardware-telemetry fte
Syntax Description
Hardware telemetry configurationhardware-telemetry
Enable/Disable Flow Table Events configurationfte
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1653
H Commandshardware-telemetry fte
Page 1798
hardware-telemetry inband-telemetry[no] hardware-telemetry inband-telemetry
Syntax Description
Hardware telemetry configurationhardware-telemetry
Enable/Disable inband telemetry configurationinband-telemetry
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1654
H Commandshardware-telemetry inband-telemetry
Page 1799
hardware-telemetry postcard-telemetry[no] hardware-telemetry postcard-telemetry
Syntax Description
Hardware telemetry configurationhardware-telemetry
Enable/Disable postcard telemetry configurationpostcard-telemetry
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1655
H Commandshardware-telemetry postcard-telemetry
Page 1800
hardware-telemetry ssx[no] hardware-telemetry ssx
Syntax Description
Hardware Telemetry Configurationshardware-telemetry
enable Streaming Statistics Exporter Configurationsssx
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1656
H Commandshardware-telemetry ssx
Page 1801
hardware access-list lou resource threshold[no] hardware access-list lou resource threshold <threshold>
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware Internal Informationhardware
Access Control Listaccess-list
LOUlou
hardware resourceresource
port expansion thresholdthreshold
value of thresholdthreshold
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1657
H Commandshardware access-list lou resource threshold
Page 1802
hardware access-list match inner-header[no] hardware access-list match inner-header
Syntax Description
(Optional) Negate the command or set its defaultsno
Change hardware usage settingshardware
Access Control Listaccess-list
Match criteria in ACLmatch
Match inner header fields in IPinIP/GRE packetsinner-header
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1658
H Commandshardware access-list match inner-header
Page 1803
hardware access-list module[no] hardware access-list { resource-pooling | resource pooling } module <module-number>
Syntax Description
(Optional) Negate a command or set its defaultsno
Show hardware informationhardware
Access Control Listaccess-list
Enable ACL programming across TCAM banksresource-pooling
hardware resourceresource
Enable ACL programming across TCAM bankspooling
module numbermodule
specify module numbermodule-number
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1659
H Commandshardware access-list module
Page 1804
hardware access-list tcam label ing-racl 9[no] hardware access-list tcam label ing-racl 9
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware Internal Informationhardware
Access Control Listaccess-list
Configure tcam parameterstcam
Tcam entry label infolabel
Ingress RACL regioning-racl
Size in bits for BD-Labels allocated to Ingress-RACL region9
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1660
H Commandshardware access-list tcam label ing-racl 9
Page 1805
hardware access-list tcam region[no] hardware access-list tcam region <type> <tcam_size>
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware Internal Informationhardware
Access Control Listaccess-list
Configure tcam parameterstcam
Configure tcam regionregion
Region typetype
Enter tcam sizetcam_size
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1661
H Commandshardware access-list tcam region
Page 1806
hardware access-list tcam region double-wide[no] hardware access-list tcam region <double-wide-region> <tcam_size> double-wide
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware Internal Informationhardware
Access Control Listaccess-list
Configure tcam parameterstcam
Configure tcam regionregion
Region typedouble-wide-region
Enter tcam sizetcam_size
Double Widthdouble-wide
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1662
H Commandshardware access-list tcam region double-wide
Page 1807
hardware access-list tcam region qualify udf[no] hardware access-list tcam region <udf_tcam_type> qualify { udf | v6udf } { <udf_name> } +
Syntax Description
(Optional) Negate the commandno
Change hardware usage settingshardware
Access Control Listaccess-list
Configure tcam parameterstcam
Configure tcam regionregion
Region typeudf_tcam_type
Configure UDFs to be qualified for regionqualify
Configure UDF namesudf
Configure IPv6 UDF namesv6udf
UDF nameudf_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1663
H Commandshardware access-list tcam region qualify udf
Page 1808
hardware access-list tcam region tcp-nat[no] hardware access-list tcam region tcp-nat <tcam_size>
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware Internal Informationhardware
Access Control Listaccess-list
Configure tcam parameterstcam
Configure tcam regionregion
TCP NAT region within NAT regiontcp-nat
Enter tcam sizetcam_size
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1664
H Commandshardware access-list tcam region tcp-nat
Page 1809
hardware ecmp hash-offset[no] hardware ecmp hash-offset <value> [ concatenation ] | no hardware ecmp hash-offset
Syntax Description
(Optional) Negate a command or set its defaultsno
Change hardware usage settingshardware
ECMP configurationecmp
Configure hash offsethash-offset
Hash offset 0-15 non-concatenate mode, 0-63 concatenate modevalue
(Optional) Configure hash concatenationconcatenation
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1665
H Commandshardware ecmp hash-offset
Page 1810
hardware ecmp hash-polynomialhardware ecmp hash-polynomial <poly-type> | no hardware ecmp hash-polynomial
Syntax Description
Negate a command or set its defaultsno
Change hardware usage settingshardware
ECMP configurationecmp
Configure hash polynomialhash-polynomial
Polynomial typepoly-type
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1666
H Commandshardware ecmp hash-polynomial
Page 1811
hardware ejector enable[no] hardware ejector enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware Internal Informationhardware
Card ejector functionalityejector
enabled means when both ejectors are open, card is powered downenable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1667
H Commandshardware ejector enable
Page 1812
hardware fan-zone raise-speed[no] hardware fan-zone <fan_zone_id> raise-speed <speed-to-raise>
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware Internal Informationhardware
Fan Zone supported in the switchfan-zone
please enter fan zone id whose speed needs to be increasedfan_zone_id
Speed to be added for current fan zone speedraise-speed
please enter additional fan speedspeed-to-raise
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1668
H Commandshardware fan-zone raise-speed
Page 1813
hardware forwarding l3 resource route non-deterministic[no] hardware forwarding l3 resource route non-deterministic
Syntax Description
(Optional) Negate a command or set its defaultsno
hardware informationhardware
forwarding informationforwarding
Layer-3l3
hardware resourcesresource
TCAM capacity to hold prefixesroute
extend upto 1Mnon-deterministic
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1669
H Commandshardware forwarding l3 resource route non-deterministic
Page 1814
hardware forwarding unicast trace[no] hardware forwarding unicast trace
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware Internal Informationhardware
Hardware forwardingforwarding
Hardware Unicast forwardingunicast
Debug tracestrace
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1670
H Commandshardware forwarding unicast trace
Page 1815
hardware ip glean throttle[no] hardware ip glean throttle
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware informationhardware
IPip
Gleanglean
Throttlethrottle
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1671
H Commandshardware ip glean throttle
Page 1816
hardware ip glean throttle maximum{ hardware ip glean throttle maximum <count> } | { no hardware ip glean throttle maximum }
Syntax Description
Negate a command or set its defaultsno
Hardware informationhardware
IPip
Gleanglean
Throttlethrottle
Maximum number of entriesmaximum
Countcount
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1672
H Commandshardware ip glean throttle maximum
Page 1817
hardware ip glean throttle syslog{ hardware ip glean throttle syslog <pkt-count> } | { no hardware ip glean throttle syslog }
Syntax Description
Negate a command or set its defaultsno
Hardware informationhardware
IPip
Gleanglean
Throttlethrottle
Threshold for syslog for number of packets hitting the entrysyslog
Packet countpkt-count
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1673
H Commandshardware ip glean throttle syslog
Page 1818
hardware ip glean throttle timeout{ hardware ip glean throttle timeout <timeout-in-sec> } | { no hardware ip glean throttle timeout }
Syntax Description
Negate a command or set its defaultsno
Hardware informationhardware
IPip
Gleanglean
Throttlethrottle
Timeouttimeout
Timeout value in seconds (should be multiple of 30, else will be roundedoff to nearest boundary)
timeout-in-sec
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1674
H Commandshardware ip glean throttle timeout
Page 1819
hardware ipv6 glean throttle[no] hardware ipv6 glean throttle
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware informationhardware
IPv6ipv6
Gleanglean
Throttlethrottle
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1675
H Commandshardware ipv6 glean throttle
Page 1820
hardware ipv6 glean throttle maximum{ hardware ipv6 glean throttle maximum <count> } | { no hardware ipv6 glean throttle maximum }
Syntax Description
Negate a command or set its defaultsno
Hardware informationhardware
IPv6ipv6
Gleanglean
Throttlethrottle
Maximum number of entriesmaximum
Countcount
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1676
H Commandshardware ipv6 glean throttle maximum
Page 1821
hardware ipv6 glean throttle syslog{ hardware ipv6 glean throttle syslog <pkt-count> } | { no hardware ipv6 glean throttle syslog }
Syntax Description
Negate a command or set its defaultsno
Hardware informationhardware
IPv6ipv6
Gleanglean
Throttlethrottle
Threshold for syslog for number of packets hitting the entrysyslog
Packet countpkt-count
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1677
H Commandshardware ipv6 glean throttle syslog
Page 1822
hardware ipv6 glean throttle timeout{ hardware ipv6 glean throttle timeout <timeout-in-sec> } | { no hardware ipv6 glean throttle timeout }
Syntax Description
Negate a command or set its defaultsno
Hardware informationhardware
IPv6ipv6
Gleanglean
Throttlethrottle
Timeouttimeout
Timeout value in seconds (should be multiple of 30, else will be roundedoff to nearest boundary)
timeout-in-sec
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1678
H Commandshardware ipv6 glean throttle timeout
Page 1823
hardware module boot-order reverse[no] hardware module boot-order reverse
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware Internal Informationhardware
applies on all the modulesmodule
Configure order of module power-upboot-order
reverse order of module power-upreverse
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1679
H Commandshardware module boot-order reverse
Page 1824
hardware multicast global-tx-span[no] hardware multicast global-tx-span
Syntax Description
(Optional) Negate a command or set its defaultsno
Change hardware usage settingshardware
Change multicast settingmulticast
Modify table programming to support TX multicast SPAN across slicesglobal-tx-span
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1680
H Commandshardware multicast global-tx-span
Page 1825
hardware profile buffer info poll-interval timer[no] hardware profile buffer info poll-interval [ module <module> ] timer <msec>
Syntax Description
(Optional) Negate a command or set its defaultsno
Change hardware usage settingshardware
profile settingsprofile
Bufferbuffer
Informationinfo
System buffer status polling intervalpoll-interval
(Optional) Slot/modulemodule
(Optional) Slot/module numbermodule
Polling timertimer
Polling timer value in msecsmsec
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1681
H Commandshardware profile buffer info poll-interval timer
Page 1826
hardware profile buffer info port-threshold threshold[no] hardware profile buffer info port-threshold [ module <module> ] threshold <value>
Syntax Description
(Optional) Negate a command or set its defaultsno
Change hardware usage settingshardware
profile settingsprofile
Bufferbuffer
Informationinfo
Set port egress buffer usage thresholdport-threshold
(Optional) Slot/modulemodule
(Optional) Slot/module numbermodule
threshold valuethreshold
percentage of maximum usagevalue
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1682
H Commandshardware profile buffer info port-threshold threshold
Page 1827
hardware profile buffer monitor unicasthardware profile buffer monitor { unicast | multicast } [ internal ] [ sampling <sampling> ] [ threshold<threshold> ] [ interface <intf-num> | sclass <sclass> ] | no hardware profile buffer monitor
Syntax Description
Negate a command or set its defaultsno
Configure hardware profile buffer monitor settingshardware
profile buffer monitor settingsprofile
Bufferbuffer
buffer monitormonitor
unicastunicast
multicastmulticast
(Optional) enable buffer monitoring internal modeinternal
(Optional) sampling interval in nano-secondssampling
(Optional) sampling interval in nano-secondssampling
(Optional) histogram threshold in Kbytes with 384 Kbytes incrementthreshold
(Optional) histogram threshold in Kbytes with 384 Kbytes incrementthreshold
(Optional) enable buffer monitoring on an interfaceinterface
(Optional) enable buffer monitoring on an interfaceintf-num
(Optional) enable buffer monitoring on a system class of servicessclass
(Optional) enable buffer monitoring on a system class of servicessclass
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1683
H Commandshardware profile buffer monitor unicast
Page 1828
hardware profile buffer qosgroup threshold[no] hardware profile buffer qosgroup <groupid> threshold <percentage>
Syntax Description
(Optional) Negate the commandno
N3500hardware
Profileprofile
Bufferbuffer
Qos-groupqosgroup
Group-idgroupid
Thresholdthreshold
Percentage of maximum usagepercentage
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1684
H Commandshardware profile buffer qosgroup threshold
Page 1829
hardware profile buffer span-threshold[no] hardware profile buffer span-threshold <percentage>
Syntax Description
(Optional) Negate the commandno
N3500hardware
Profileprofile
Bufferbuffer
Span Thresholdspan-threshold
Percentage of maximum usagepercentage
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1685
H Commandshardware profile buffer span-threshold
Page 1830
hardware profile ecmp auto-recovery thresholdhardware profile ecmp auto-recovery threshold <percentage> | no hardware profile ecmp auto-recoverythreshold
Syntax Description
Negate a command or set its defaultsno
Change hardware usage settingshardware
profile settingsprofile
ECMP settingsecmp
ECMP auto-recovery settingsauto-recovery
ECMP table free percentage threshold for auto-recoverythreshold
Percentagepercentage
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1686
H Commandshardware profile ecmp auto-recovery threshold
Page 1831
hardware profile ecmp resilient[no] hardware profile ecmp resilient
Syntax Description
(Optional) Negate a command or set its defaultsno
Change hardware usage settingshardware
profile settingsprofile
ECMP settingsecmp
Configure ECMP resilient moderesilient
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1687
H Commandshardware profile ecmp resilient
Page 1832
hardware profile ecmp template module[no] hardware profile ecmp template [ l3vpn ] module <module>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set hardware profilehardware
Profile settingsprofile
set the ecmp template profileecmp
set the ecmp template profiletemplate
(Optional) set the l3vpn ecmp template profilel3vpn
Enter module numbermodule
module
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1688
H Commandshardware profile ecmp template module
Page 1833
hardware profile forwarding-mode[no] hardware profile forwarding-mode { warp [ lpm-entry <lpm_warp> host-entry <host> l2-entry <l2>mcast-entry <mcst_warp> ] | openflow-hybrid | openflow-only | normal [ lpm-entry <ipv4> mcast-entry<mcst> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Change hardware usage settingshardware
profile settingsprofile
Forwarding mode settingforwarding-mode
Warp forwarding mode settingwarp
Openflow hybrid forwarding mode settingopenflow-hybrid
Openflow only forwarding mode settingopenflow-only
Normal forwarding mode settingnormal
(Optional) 4K aligned total IPv4 entrieslpm-entry
(Optional) 4K aligned total IPv4 entriesipv4
(Optional) 4K aligned total Mcast entriesmcast-entry
(Optional) 4K aligned total Mcast entriesmcst
(Optional) 4K aligned total IPv4 entrieslpm_warp
(Optional) 4K aligned total Mcast entriesmcst_warp
(Optional) 4K aligned total Host entrieshost-entry
(Optional) 4K aligned total Host entrieshost
(Optional) 4K aligned total L2 entriesl2-entry
(Optional) 4K aligned total L2 entriesl2
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1689
H Commandshardware profile forwarding-mode
Page 1834
hardware profile front portmodehardware profile front portmode <port-mode> | no hardware profile front portmode
Syntax Description
Negate a command or set its defaultsno
Change hardware usage settingshardware
profile settingsprofile
port 1 QSFP/SFP+ settingsfront
QSFP or SFP+portmode
Configure QSFP/sfp+ port modeport-mode
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1690
H Commandshardware profile front portmode
Page 1835
hardware profile ipv6 alpm carve-value[no] hardware profile ipv6 alpm carve-value <ipv6_alpm_carve_value>
Syntax Description
(Optional) Negate the commandno
Change hardware usage settingshardware
profile settingsprofile
ipv6ipv6
alpm modealpm
carve valuecarve-value
maximum entriesipv6_alpm_carve_value
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1691
H Commandshardware profile ipv6 alpm carve-value
Page 1836
hardware profile ipv6 lpm-entries maximum[no] hardware profile ipv6 lpm-entries maximum <ipv6_lpm_max_entry>
Syntax Description
(Optional) Negate the commandno
Change hardware usage settingshardware
profile settingsprofile
ipv6ipv6
lpm(non-host) entrieslpm-entries
maximum limitmaximum
maximum entriesipv6_lpm_max_entry
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1692
H Commandshardware profile ipv6 lpm-entries maximum
Page 1837
hardware profile latency monitorhardware profile latency monitor [ threshold-avg <threshold-avg> ] [ threshold-max <threshold-max> ] [sampling <sampling> ] | no hardware profile latency monitor
Syntax Description
Negate a command or set its defaultsno
Configure hardware profile latency monitor settingshardware
profile latency monitor settingsprofile
latencylatency
latency monitormonitor
(Optional) average latency threshold in nano-secondsthreshold-avg
(Optional) average latency threshold in nano-secondsthreshold-avg
(Optional) maximum latency threshold in nano-secondsthreshold-max
(Optional) maximum latency threshold in nano-secondsthreshold-max
(Optional) sampling interval in secondssampling
(Optional) sampling interval in secondssampling
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1693
H Commandshardware profile latency monitor
Page 1838
hardware profile module[no] hardware profile [ vxlan | mpls ] module { all | <module> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set hardware profilehardware
Profile settingsprofile
(Optional) Set the hardware profile for module to vxlanvxlan
(Optional) Set the hardware profile for module to mplsmpls
Enter module numbermodule
All modulesall
module
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1694
H Commandshardware profile module
Page 1839
hardware profile multicast flex-stats-enable[no] hardware profile multicast flex-stats-enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Change hardware usage settingshardware
profile settingsprofile
Multicast settingsmulticast
Enable real time statsflex-stats-enable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1695
H Commandshardware profile multicast flex-stats-enable
Page 1840
hardware profile multicast max-limit{ hardware profile multicast max-limit <mcast-ent> } | { no hardware profile multicast max-limit }
Syntax Description
Negate the commandno
Change hardware usage settingshardware
profile settingsprofile
Multicast settingsmulticast
maximum limit for multicast entriesmax-limit
Mcast Table Entriesmcast-ent
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1696
H Commandshardware profile multicast max-limit
Page 1841
hardware profile multicast max-limit lpm-entries[no] hardware profile multicast max-limit lpm-entries <ipv4_mcast_lpm_max_entry>
Syntax Description
(Optional) Negate the commandno
Change hardware usage settingshardware
profile settingsprofile
Multicast settingsmulticast
maximum limit for multicast entriesmax-limit
lpm(non-host) entrieslpm-entries
maximum entriesipv4_mcast_lpm_max_entry
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1697
H Commandshardware profile multicast max-limit lpm-entries
Page 1842
hardware profile multicast nlb[no] hardware profile multicast nlb
Syntax Description
(Optional) Negate the commandno
Change hardware usage settingshardware
profile settingsprofile
Multicast settingsmulticast
network load balancing for multicast entriesnlb
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1698
H Commandshardware profile multicast nlb
Page 1843
hardware profile multicast optimization disable[no] hardware profile multicast optimization disable
Syntax Description
(Optional) Negate a command or set its defaultsno
Set hardware profilehardware
Profile settingsprofile
set multicast profilemulticast
set multicast optimization profileoptimization
set the multicast optimization disable profiledisable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1699
H Commandshardware profile multicast optimization disable
Page 1844
hardware profile multicast prefer-source-tree[no] hardware profile multicast prefer-source-tree [ eternity [ limit <max-limit> ] ]
Syntax Description
(Optional) Negate the commandno
Change hardware usage settingshardware
profile settingsprofile
Multicast settingsmulticast
prefer the source treeprefer-source-tree
(Optional) prefer source tree for eternity and not for just 2 minuteseternity
(Optional) Configure a limit for the number of hardware entries usedlimit
(Optional) Number of (S,G) for which source tree is preferredmax-limit
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1700
H Commandshardware profile multicast prefer-source-tree
Page 1845
hardware profile multicast rpf-check-optimization{ hardware profile multicast rpf-check-optimization } | { no hardware profile multicast rpf-check-optimization}
Syntax Description
Negate the commandno
Change hardware usage settingshardware
profile settingsprofile
Multicast settingsmulticast
RPF Check optimization on Monticello ASICrpf-check-optimization
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1701
H Commandshardware profile multicast rpf-check-optimization
Page 1846
hardware profile multicast service-reflect port{ hardware profile multicast service-reflect port <port-num> } | { no hardware profile multicast service-reflect}
Syntax Description
Negate a command or set its defaultsno
Change hardware usage settingshardware
profile settingsprofile
Multicast settingsmulticast
service-reflect settingsservice-reflect
loopback portport
loopback port-numport-num
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1702
H Commandshardware profile multicast service-reflect port
Page 1847
hardware profile multicast slow-receiver porthardware profile multicast slow-receiver port <port> | no hardware profile multicast slow-receiver port <port>
Syntax Description
Negate the commandno
Change hardware usage settingshardware
Profileprofile
Multicast settingsmulticast
Multicast slow receiverslow-receiver
Portport
Port numberport
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1703
H Commandshardware profile multicast slow-receiver port
Page 1848
hardware profile multicast syslog-threshold[no] hardware profile multicast syslog-threshold <percentage>
Syntax Description
(Optional) Negate the commandno
Change hardware usage settingshardware
profile settingsprofile
Multicast settingsmulticast
MROUTE table syslog thresholdsyslog-threshold
Percentage (Default is 90)percentage
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1704
H Commandshardware profile multicast syslog-threshold
Page 1849
hardware profile openflow[no] hardware profile { openflow [ agent default { drop | normal } ] | { tap-aggregation [ l2drop ] } }
Syntax Description
(Optional) Negate the commandno
Hardware Internal Informationhardware
Profileprofile
Openflowopenflow
Tap Aggregationtap-aggregation
(Optional) Drop non IP traffic ingress on mode tap interfacesl2drop
(Optional) Act as Openflow Agentagent
(Optional) Specify default action for frames which don't match any flowdefault
(Optional) Drop all frames that miss MACdrop
(Optional) [default]Flood unknown trafficnormal
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1705
H Commandshardware profile openflow
Page 1850
hardware profile packet-drop[no] hardware profile packet-drop
Syntax Description
(Optional) Negate a command or set its defaultsno
Change hardware usage settingshardware
Profile settingsprofile
Configure Packet Drop parameterspacket-drop
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1706
H Commandshardware profile packet-drop
Page 1851
hardware profile pbr skip-selfip[no] hardware profile pbr skip-selfip
Syntax Description
(Optional) Negate a command or set its defaultsno
Change hardware usage settingshardware
profile settingsprofile
PBR feature settingspbr
Configure Skipping PBR for self-ip packetsskip-selfip
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1707
H Commandshardware profile pbr skip-selfip
Page 1852
hardware profile pfc mmu buffer-reservation[no] hardware profile pfc mmu buffer-reservation <percentage>
Syntax Description
(Optional) Negate the commandno
Hardware Internal Informationhardware
profile settingsprofile
System level priority-flow-control settingspfc
Hardware memory management unit configurationmmu
Shared pool buffer reservationbuffer-reservation
Percentage of shared pool buffers to be reservedpercentage
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1708
H Commandshardware profile pfc mmu buffer-reservation
Page 1853
hardware profile portmode{ hardware profile portmode <port-mode> [ 2-tuple ] } | no hardware profile portmode
Syntax Description
Negate a command or set its defaultsno
Change hardware usage settingshardware
profile settingsprofile
QSFP port mode settingportmode
Configure QSFP port modeport-mode
(Optional) Display QSFP portnames in 2-tuple mode even in 10Gmode2-tuple
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1709
H Commandshardware profile portmode
Page 1854
hardware profile statistics pstat[no] hardware profile statistics pstat [ peak ]
Syntax Description
(Optional) Negate the commandno
Configure hardware profile settinghardware
profile settingsprofile
hardware statsstatistics
Enable Pstat default is instantaneouspstat
(Optional) Peak statspeak
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1710
H Commandshardware profile statistics pstat
Page 1855
hardware profile svi flex-stats-enable[no] hardware profile svi flex-stats-enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Change hardware usage settingshardware
profile settingsprofile
SVI settingssvi
Enable real time statsflex-stats-enable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1711
H Commandshardware profile svi flex-stats-enable
Page 1856
hardware profile tcam ipv6-sup-tcam match-inner{ hardware profile tcam ipv6-sup-tcammatch-inner } | { no hardware profile tcam ipv6-sup-tcammatch-inner}
Syntax Description
Negate a command or set its defaultsno
Change hardware usage settingshardware
Profile settingsprofile
Configure tcam parameterstcam
IPv6 SUP TCAM parametersipv6-sup-tcam
match inner payload for tunnel packetsmatch-inner
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1712
H Commandshardware profile tcam ipv6-sup-tcam match-inner
Page 1857
hardware profile tcam region[no] hardware profile tcam region { <tcam_compat_type> <tcam_compat_size> | ifacl <tcam_compat_size>[ double-wide ] | nat <tcam_compat_size> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware Internal Informationhardware
profileprofile
Configure tcam parameterstcam
Configure tcam regionregion
IPV4 PACL sizeifacl
(Optional) Configure tcam as double widedouble-wide
NAT sizenat
tcam_compat_type
Enter tcam sizetcam_compat_size
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1713
H Commandshardware profile tcam region
Page 1858
hardware profile tcam region span qualify udf[no] hardware profile tcam region span qualify udf { <udf_name> } +
Syntax Description
(Optional) Negate the commandno
Change hardware usage settingshardware
Profile settingsprofile
Configure tcam parameterstcam
Configure tcam regionregion
Configure for span regionspan
Configure UDFs to be qualified for span regionqualify
Configure UDF namesudf
UDF nameudf_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1714
H Commandshardware profile tcam region span qualify udf
Page 1859
hardware profile tcam region spanv6-l2 qualify udf[no] hardware profile tcam region spanv6-l2 qualify udf { <udf_name> } +
Syntax Description
(Optional) Negate the commandno
Change hardware usage settingshardware
Profile settingsprofile
Configure tcam parameterstcam
Configure tcam regionregion
Configure for span regionspanv6-l2
Configure UDFs to be qualified for span regionqualify
Configure UDF namesudf
UDF nameudf_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1715
H Commandshardware profile tcam region spanv6-l2 qualify udf
Page 1860
hardware profile tcam region spanv6 qualify udf[no] hardware profile tcam region spanv6 qualify udf { <udf_name> } +
Syntax Description
(Optional) Negate the commandno
Change hardware usage settingshardware
Profile settingsprofile
Configure tcam parameterstcam
Configure tcam regionregion
Configure for span regionspanv6
Configure UDFs to be qualified for span regionqualify
Configure UDF namesudf
UDF nameudf_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1716
H Commandshardware profile tcam region spanv6 qualify udf
Page 1861
hardware profile tcam resource service-template[no] hardware profile tcam resource service-template { <name> } [ module { <lc> | <fm> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Change hardware usage settingshardware
Profile settingsprofile
Configure tcam parameterstcam
Configure tcam hardware resourcesresource
Commit templateservice-template
Select name of templatename
(Optional) Specify a module numbermodule
(Optional) line card numberlc
(Optional) fabric module numberfm
Command Mode
• /exec/configure handle auto 424
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1717
H Commandshardware profile tcam resource service-template
Page 1862
hardware profile tcam resource template[no] hardware profile tcam resource template { <name> { ref-template <temp-nontahoe> | ref-template-tahoe<temp-tahoe> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Change hardware usage settingshardware
Profile settingsprofile
Configure tcam parameterstcam
Configure tcam hardware resourcesresource
Configure template based tcam carving parameterstemplate
Select a default template as referenceref-template
temp-nontahoe
Select a default template as referenceref-template-tahoe
temp-tahoe
Create/Select name of custom templatename
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1718
H Commandshardware profile tcam resource template
Page 1863
hardware profile tcam syslog-threshold{ hardware profile tcam syslog-threshold <percentage> } | { no hardware profile tcam syslog-threshold }
Syntax Description
Negate a command or set its defaultsno
Change hardware usage settingshardware
Profile settingsprofile
Configure tcam parameterstcam
TCAMs syslog thresholdsyslog-threshold
Percentagepercentage
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1719
H Commandshardware profile tcam syslog-threshold
Page 1864
hardware profile ucast6 lpm-65-to-127-max-limit{ hardware profile ucast6 lpm-65-to-127-max-limit <unicast-ent> } | { no hardware profile ucast6lpm-65-to-127-max-limit }
Syntax Description
Negate the commandno
Change hardware usage settingshardware
profile settingsprofile
unicast ipv6 settingsucast6
maximum limit for unicast ipv6 lpm-65-to-127 entries, default is 256lpm-65-to-127-max-limit
Unicast ipv6 lpm-65-to-127 Table Entriesunicast-ent
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1720
H Commandshardware profile ucast6 lpm-65-to-127-max-limit
Page 1865
hardware profile ucast6 max-limit{ hardware profile ucast6 max-limit <unicast-ent> } | { no hardware profile ucast6 max-limit }
Syntax Description
Negate the commandno
Change hardware usage settingshardware
profile settingsprofile
unicast ipv6 settingsucast6
maximum limit for unicast ipv6 entriesmax-limit
Unicast ipv6 Table Entriesunicast-ent
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1721
H Commandshardware profile ucast6 max-limit
Page 1866
hardware profile unicast enable-host-ecmp[no] hardware profile unicast enable-host-ecmp [ arp-nd | [ ipv4 [ arp ] ] | [ ipv6 [ nd ] ] ]
Syntax Description
(Optional) Negate the commandno
Change hardware usage settingshardware
profile settingsprofile
Unicast settingsunicast
Enable ECMP support for /32 (IPv4) and /128 (IPv6) routesenable-host-ecmp
(Optional) Enable ECMP support for /32 (IPv4 Only) Routesipv4
(Optional) Enable ECMP support for /128 (IPv6 Only) Routesipv6
(Optional) Retain ARP (IPv4) and ND (IPv6) Routes in Host-Tablearp-nd
(Optional) Retain ARP Entries in Host-Tablearp
(Optional) Retain ND Entries in Host-Tablend
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1722
H Commandshardware profile unicast enable-host-ecmp
Page 1867
hardware profile unicast syslog-threshold{ hardware profile unicast syslog-threshold <percentage> } | { no hardware profile unicast syslog-threshold}
Syntax Description
Negate the commandno
Change hardware usage settingshardware
profile settingsprofile
Unicast settingsunicast
Unicast Route table syslog thresholdsyslog-threshold
Percentagepercentage
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1723
H Commandshardware profile unicast syslog-threshold
Page 1868
hardware qos dynamic-buffer-sharing[no] hardware qos dynamic-buffer-sharing
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware Internal Informationhardware
Configure qos related configurationqos
Enable dynamic buffer sharingdynamic-buffer-sharing
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1724
H Commandshardware qos dynamic-buffer-sharing
Page 1869
hardware qos fc rate-shaper[no] hardware qos fc rate-shaper [ low ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware Internal Informationhardware
Configure qos related configurationqos
Fibre Channel interface related configurationfc
Rate Shaper for FC interfacerate-shaper
(Optional) Configure FC interface low rate shaperlow
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1725
H Commandshardware qos fc rate-shaper
Page 1870
hardware qos pfc mc-drop[no] hardware qos pfc mc-drop
Syntax Description
(Optional) Negate a command or set its defaultsno
Hardware Internal Informationhardware
Configure qos related configurationqos
Priority-flow-control specific configurationpfc
Multicast packets are droped in lossless queuemc-drop
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1726
H Commandshardware qos pfc mc-drop
Page 1871
hardware sample-redirect module redirect-interfacehardware sample-redirect module <num> redirect-interface <interface>
Syntax Description
Change hardware usage settingshardware
Redirect netflow sampled datasample-redirect
Line card modulemodule
slot numbernum
Interface for redirecting the trafficredirect-interface
Interface Nameinterface
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1727
H Commandshardware sample-redirect module redirect-interface
Page 1872
head| head [ -n <lines> ]
Syntax Description
Pipe command output to filter|
Display first lineshead
(Optional) modify number of lines (default 10)-n
(Optional) number of lines to printlines
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1728
H Commandshead
Page 1873
header-type 2[no] header-type { 2 | 3 [ rfc-compliant ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set ERSPAN Source versionheader-type
ERSPAN Source Version 22
ERSPAN Source Version 33
(Optional) ERSPAN V3 header rfc-compliantrfc-compliant
Command Mode
• /exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1729
H Commandsheader-type 2
Page 1874
hello-interval{ { hello-interval <interval> } | { no hello-interval [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Hello intervalhello-interval
(seconds)interval
Command Mode
• /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1730
H Commandshello-interval
Page 1875
hello-interval{ { hello-interval <interval> } | { no hello-interval [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Hello intervalhello-interval
(seconds)interval
Command Mode
• /exec/configure/router-ospf3/router-ospf3-vlink /exec/configure/router-ospf3/vrf/router-ospf3-vlink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1731
H Commandshello-interval
Page 1876
hello-interval{ { hello-interval <interval> } | { no hello-interval [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Hello intervalhello-interval
(seconds)interval
Command Mode
• /exec/configure/router-ospf/vrf/router-ospf-slink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1732
H Commandshello-interval
Page 1877
history{ no | default } history { { buckets-kept } | { distributions-of-statistics-kept } | { filter } | {hours-of-statistics-kept } | { lives-kept } | { statistics-distribution-interval } }
Syntax Description
no
Set a command to its defaultsdefault
History and Distribution Datahistory
Maximum number of history buckets to collectbuckets-kept
Maximum number of statistics distribution buckets to capturedistributions-of-statistics-kept
Add operation to History when...filter
Maximum number of statistics hour groups to capturehours-of-statistics-kept
Maximum number of history lives to collectlives-kept
Statistics distribution interval sizestatistics-distribution-interval
Command Mode
• /exec/configure/ip-sla/dns /exec/configure/ip-sla/fabricPathEcho /exec/configure/ip-sla/http
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1733
H Commandshistory
Page 1878
history{ no | default } history { { buckets-kept } | { distributions-of-statistics-kept } | { enhanced [ interval [<interval-seconds> [ buckets [ <num-buckets> ] ] ] ] } | { filter } | { hours-of-statistics-kept } | { lives-kept }| { statistics-distribution-interval } }
Syntax Description
no
(Optional) bucketsinterval
Set a command to its defaultsdefault
History and Distribution Datahistory
Maximum number of history buckets to collectbuckets-kept
Maximum number of statistics distribution buckets to capturedistributions-of-statistics-kept
Enable enhanced history collectionenhanced
(Optional) Interval in secondsinterval-seconds
(Optional) Number of buckets to collect databuckets
(Optional) Number of bucketsnum-buckets
Add operation to History when...filter
Maximum number of statistics hour groups to capturehours-of-statistics-kept
Maximum number of history lives to collectlives-kept
Statistics distribution interval sizestatistics-distribution-interval
Command Mode
• /exec/configure/ip-sla/udp /exec/configure/ip-sla/tcp /exec/configure/ip-sla/icmpEcho
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1734
H Commandshistory
Page 1879
historyhistory { { buckets-kept <num-buckets-kept> } | { distributions-of-statistics-kept <num-dist-stats> } | {enhanced [ interval [ <interval-seconds> [ buckets [ <num-buckets> ] ] ] ] } | { filter { all | failures | none |overThreshold } } | { hours-of-statistics-kept <num-hours-of-stats> } | { lives-kept <life-size-value> } | {statistics-distribution-interval <dist-interval> } }
Syntax Description
(Optional) bucketsinterval
(Optional) <num-buckets>interval-seconds
<dist-interval>life-size-value
History and Distribution Datahistory
Maximum number of history buckets to collectbuckets-kept
Bucket size value (default 15)num-buckets-kept
Maximum number of statistics distribution buckets to capturedistributions-of-statistics-kept
Distribution bucket size value (default 1)num-dist-stats
Enable enhanced history collectionenhanced
(Optional) Number of buckets to collect databuckets
(Optional) Number of bucketsnum-buckets
Add operation to History when...filter
Collect every operation in Historyall
Collect operations that fail in Historyfailures
Shutoff History collectionnone
Collect operations that are over threshold in HistoryoverThreshold
Maximum number of statistics hour groups to capturehours-of-statistics-kept
Hour groups size value (default 2)num-hours-of-stats
Maximum number of history lives to collectlives-kept
Statistics distribution interval sizestatistics-distribution-interval
Distribution interval value in msec (default 20ms), Value in usec ifprecision microsecond is enabled
dist-interval
Command Mode
• /exec/configure/ip-sla/udp /exec/configure/ip-sla/tcp /exec/configure/ip-sla/icmpEcho
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1735
H Commandshistory
Page 1880
historyhistory { { buckets-kept <num-buckets-kept> } | { distributions-of-statistics-kept <num-dist-stats> } | { filter{ all | failures | none | overThreshold } } | { hours-of-statistics-kept <num-hours-of-stats> } | { lives-kept<life-size-value> } | { statistics-distribution-interval <dist-interval> } }
Syntax Description
<num-buckets-kept>dist-interval
<life-size-value>num-hours-of-stats
hours-of-statistics-keptdistributions-of-statistics-kept
statistics-distribution-interval
History and Distribution Datahistory
Maximum number of history buckets to collectbuckets-kept
Bucket size value (default 15)num-buckets-kept
Distribution bucket size value (default 1)num-dist-stats
Add operation to History when...filter
Collect every operation in Historyall
Collect operations that fail in Historyfailures
Shutoff History collectionnone
Collect operations that are over threshold in HistoryoverThreshold
Maximum number of statistics hour groups to capturehours-of-statistics-kept
Maximum number of history lives to collectlives-kept
Life size value (default 0)life-size-value
Command Mode
• /exec/configure/ip-sla/dns /exec/configure/ip-sla/fabricPathEcho /exec/configure/ip-sla/http
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1736
H Commandshistory
Page 1881
history{ no | default } history { { distributions-of-statistics-kept } | { enhanced [ interval [ <interval-seconds> [buckets [ <num-buckets> ] ] ] ] } | { hours-of-statistics-kept } | { statistics-distribution-interval } }
Syntax Description
no
(Optional) bucketsinterval
hours-of-statistics-keptdistributions-of-statistics-kept
statistics-distribution-interval
Set a command to its defaultsdefault
History and Distribution Datahistory
Enable enhanced history collectionenhanced
(Optional) Interval in secondsinterval-seconds
(Optional) Number of buckets to collect databuckets
(Optional) Number of bucketsnum-buckets
Maximum number of statistics hour groups to capturehours-of-statistics-kept
Command Mode
• /exec/configure/ip-sla/jitter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1737
H Commandshistory
Page 1882
historyhistory { { distributions-of-statistics-kept <num-dist-stats> } | { enhanced [ interval [ <interval-seconds> [buckets [ <num-buckets> ] ] ] ] } | { hours-of-statistics-kept <num-hours-of-stats> } | {statistics-distribution-interval <dist-interval> } }
Syntax Description
(Optional) bucketsinterval
(Optional) <num-hours-of-stats>num-buckets
hours-of-statistics-keptenhanced
History and Distribution Datahistory
Maximum number of statistics distribution buckets to capturedistributions-of-statistics-kept
Distribution bucket size value (default 1)num-dist-stats
(Optional) Interval in secondsinterval-seconds
(Optional) Number of buckets to collect databuckets
Maximum number of statistics hour groups to capturehours-of-statistics-kept
Hour groups size value (default 2)num-hours-of-stats
Statistics distribution interval sizestatistics-distribution-interval
Distribution interval value in msec (default 20ms), Value in usec ifprecision microsecond is enabled
dist-interval
Command Mode
• /exec/configure/ip-sla/jitter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1738
H Commandshistory
Page 1883
holdtimeholdtime { infinite | <secs> } | no holdtime
Syntax Description
Negate a command or set its defaultsno
LDP session holdtimeholdtime
Ignore LDP session holdtimeinfinite
Holdtime in secondssecs
Command Mode
• /exec/configure/ldp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1739
H Commandsholdtime
Page 1884
hop-limit maximum[no] hop-limit maximum <limit>
Syntax Description
(Optional) Negate a command or set its defaultsno
Maximum hop count value allowedlimit
Command Mode
• /exec/configure/config-ra-guard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1740
H Commandshop-limit maximum
Page 1885
hop-limit minimum[no] hop-limit minimum <limit>
Syntax Description
(Optional) Negate a command or set its defaultsno
Minimum hop count value allowedlimit
Command Mode
• /exec/configure/config-ra-guard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1741
H Commandshop-limit minimum
Page 1886
hop{ hop <val> } | { no hop }
Syntax Description
Negate a command or set its defaultsno
Configure ngoam hop counthop
Configure ngoam service hop count valueval
Command Mode
• /exec/configure/configngoamprofile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1742
H Commandshop
Page 1887
host-reachability protocol[no] host-reachability protocol { bgp | openflow | openflow-ir }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure host reachability advertisementhost-reachability
Control protocol to useprotocol
Border Gateway Protocolbgp
OpenFlowopenflow
OpenFlow-IRopenflow-ir
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1743
H Commandshost-reachability protocol
Page 1888
host[no] { host <hostaddr> | <prefix> | <addr> <mask> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Host address of the object-group memberhost
A.B.C.D Host addresshostaddr
A.B.C.D Network address of object-group memberaddr
A.B.C.D wildcardmask
A.B.C.D/nn Network prefix of the object-group memberprefix
Command Mode
• /exec/configure/objgroup
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1744
H Commandshost
Page 1889
host group permit{ <seq> host <hostip> group <range> { permit | deny } } | { no <seq> [ host <hostip> group <range> { permit| deny } ] }
Syntax Description
Sequence Numberseq
Host IP Addresshost
Host IP Addresshostip
Configure explicit group rangesgroup
Group Prefixrange
Admission Permittedpermit
Admission Denieddeny
Command Mode
• /exec/configure/nbm-host-policy/sender
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1745
H Commandshost group permit
Page 1890
host source group permit{ <seq> host <hostip> source <sourceip> group <range> { permit | deny } } | { no <seq> [ host <hostip>source <sourceip> group <range> { permit | deny } ] }
Syntax Description
Sequence Numberseq
Host IP Addresshost
Host IP Address valuehostip
Source IP Addresssource
Source IP Address valuesourceip
Configure explicit group rangesgroup
Group Prefixrange
Admission Permittedpermit
Admission Denieddeny
Command Mode
• /exec/configure/nbm-host-policy/receiver
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1746
H Commandshost source group permit
Page 1891
hostname{ hostname | switchname } <name> | no { hostname | switchname }
Syntax Description
Negate a command or set its defaultsno
Configure system's host namehostname
Configure system's host nameswitchname
Enter switchnamename
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1747
H Commandshostname
Page 1892
hostname dynamic[no] hostname dynamic
Syntax Description
(Optional) Negate a command or set its defaultsno
Set dynamic hostname for IS-IShostname
Dynamic hostnamedynamic
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1748
H Commandshostname dynamic
Page 1893
hostname dynamic[no] hostname dynamic
Syntax Description
(Optional) Negate a command or set its defaultsno
Set dynamic hostname for IS-IShostname
Dynamic hostnamedynamic
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1749
H Commandshostname dynamic
Page 1894
hostname dynamic[no] hostname dynamic
Syntax Description
(Optional) Negate a command or set its defaultsno
Set dynamic hostname for IS-IShostname
Dynamic hostnamedynamic
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1750
H Commandshostname dynamic
Page 1895
hsrp[no] hsrp <group-id> [ ipv4 ]
Syntax Description
(Optional) Negate a command or set its defaultsno
HSRP interface configuration commandshsrp
Group number (0-255 for HSRPv1)group-id
(Optional) Configure IP Version 4 groupipv4
Command Mode
• /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel/exec/configure/if-sub /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1751
H Commandshsrp
Page 1896
hsrp anycast[no] hsrp anycast <id> { ipv4 | ipv6 | both }
Syntax Description
(Optional) Negate a command or set its defaultsno
HSRP configuration commandshsrp
Anycast related commandsanycast
Bundle numberid
Associate IP Version 4 for the bundleipv4
Associate IP Version 6 for the bundleipv6
Associate IP Version 4 and 6 for the bundleboth
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1752
H Commandshsrp anycast
Page 1897
hsrp bfd[no] hsrp bfd
Syntax Description
(Optional) Negate a command or set its defaultsno
HSRP interface configuration commandshsrp
BFD protocolbfd
Command Mode
• /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel/exec/configure/if-sub /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1753
H Commandshsrp bfd
Page 1898
hsrp bfd all-interfaces[no] hsrp bfd all-interfaces
Syntax Description
(Optional) Negate a command or set its defaultsno
HSRP interface configuration commandshsrp
BFD protocolbfd
On all interfacesall-interfaces
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1754
H Commandshsrp bfd all-interfaces
Page 1899
hsrp delay minimumhsrp delay { minimum <min-delay> | reload <reload-delay> } + | no hsrp delay [ minimum | reload ]
Syntax Description
Negate a command or set its defaultsno
HSRP interface configuration commandshsrp
HSRP initialisation delaydelay
Minimum delayminimum
Delay after reloadreload
<0-10000> Delay in secondsmin-delay
<0-10000> Delay in secondsreload-delay
Command Mode
• /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel/exec/configure/if-sub /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1755
H Commandshsrp delay minimum
Page 1900
hsrp force state vlanhsrp force state vlan { <vlans> | all }
Syntax Description
Hot Standby Router Protocol (HSRP) informationhsrp
Move the HSRP stateforce
HSRP statestate
HSRP state changes for these vlansvlan
Include all HSRP configured VLANsall
VLAN IDs of the VLAN for which state change will affectvlans
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1756
H Commandshsrp force state vlan
Page 1901
hsrp ipv6[no] hsrp <group-id> ipv6
Syntax Description
(Optional) Negate a command or set its defaultsno
HSRP interface configuration commandshsrp
Group numbergroup-id
Configure IP Version 6 groupipv6
Command Mode
• /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel/exec/configure/if-sub /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1757
H Commandshsrp ipv6
Page 1902
hsrp mac-refreshhsrp mac-refresh [ <time> ] | no hsrp mac-refresh
Syntax Description
Negate a command or set its defaultsno
HSRP interface configuration commandshsrp
Interface mac-refresh timemac-refresh
(Optional) Timeout value (0-10000) in sectime
Command Mode
• /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel/exec/configure/if-sub /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1758
H Commandshsrp mac-refresh
Page 1903
hsrp timers extended-hold[no] hsrp timers extended-hold [ <extended-hold> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
HSRP interface configuration commandshsrp
Global Timerstimers
Extended Holdextended-hold
(Optional) Time in secondsextended-hold
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1759
H Commandshsrp timers extended-hold
Page 1904
hsrp use-bia[no] hsrp use-bia [ scope interface ]
Syntax Description
(Optional) Negate a command or set its defaultsno
HSRP interface configuration commandshsrp
HSRP uses interface's burned in addressuse-bia
(Optional) Specify the scope of use-biascope
(Optional) Use-bia applies to all groups on this interface or sub-interfaceinterface
Command Mode
• /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel/exec/configure/if-sub /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1760
H Commandshsrp use-bia
Page 1905
hsrp version 1hsrp version { 1 | 2 } | no hsrp version
Syntax Description
Negate a command or set its defaultsno
HSRP interface configuration commandshsrp
HSRP versionversion
Version 11
Version 22
Command Mode
• /exec/configure/if-eth-any /exec/configure/if-vlan-common /exec/configure/if-port-channel/exec/configure/if-sub /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1761
H Commandshsrp version 1
Page 1906
http get[no] http { get } <WORD> { [ cache { disable | enable } ] [ proxy <proxy-info> ] [ source-ip {<source-ip-hostname> | <source-ip-address> } ] [ source-port <src-port> ] [ version <http-version> ] } +
Syntax Description
(Optional)no
(Optional) enablecache
(Optional) <proxy-info>proxy
(Optional) <source-ip-hostname>source-ip
(Optional) <src-port>source-port
(Optional) <http-version>version
HTTP Operationhttp
HTTP get operationget
URLWORD
(Optional) enable download of cached entries (default)enable
(Optional) disable download of cached entries (default)disable
(Optional) proxy information stringproxy-info
(Optional) source IP hostname, broadcast disallowedsource-ip-hostname
(Optional) source IP address, broadcast disallowedsource-ip-address
(Optional) Port Number (Recommended port range between 1025-65534)src-port
(Optional) Supported HTTP versions are '1.0' and '1.1'.http-version
Command Mode
• /exec/configure/ip-sla
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1762
H Commandshttp get
Page 1907
http proxy server[no] http proxy server <hostipname> [ port <port-num> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure http related parametershttp
Http Proxy related parametersproxy
Server addressserver
IPV4/IPV6 address or DNS name of proxy serverhostipname
(Optional) Http proxy server portport
(Optional) port numberport-num
Command Mode
• /exec/configure/trustpool
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1763
H Commandshttp proxy server
Page 1908
human| human
Syntax Description
Pipe command output to filter|
output in human formathuman
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1764
H Commandshuman
Page 1909
human| human
Syntax Description
Pipe command output to filter|
output in human formathuman
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1765
H Commandshuman
Page 1910
hw-module logging onboard[no] hw-module logging onboard [ { counter-stats | module <module> [ { counter-stats } ] } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/Disable OBFL informationhw-module
Enable/Disable OBFL informationlogging
Enable/Disable OBFL informationonboard
(Optional) Enable/Disable OBFL counter statisticscounter-stats
(Optional) Enable/Disable OBFL information for Modulemodule
(Optional) Enter module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1766
H Commandshw-module logging onboard
Page 1911
hw-module logging onboard[no] hw-module logging onboard [ { environmental-history | error-stats | interrupt-stats | module <module>[ { environmental-history | error-stats | interrupt-stats | obfl-logs | cpuhog } ] | obfl-logs | cpuhog } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/Disable OBFL informationhw-module
Enable/Disable OBFL informationlogging
Enable/Disable OBFL informationonboard
(Optional) Enable/Disable OBFL environmental historyenvironmental-history
(Optional) Enable/Disable OBFL error statisticserror-stats
(Optional) Enable/Disable OBFL interrupt statisticsinterrupt-stats
(Optional) Enable/Disable OBFL cpu hog eventscpuhog
(Optional) Enable/Disable OBFL information for Modulemodule
(Optional) Enter module numbermodule
(Optional) Enable/Disable OBFL(boot-uptime/device-version/obfl-history)
obfl-logs
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1767
H Commandshw-module logging onboard
Page 1912
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1768
H Commandshw-module logging onboard
Page 1913
I Commands
• icam monitor entries acl module inst, on page 1786• icam monitor interval num_intervals, on page 1787• icam monitor resource acl_tcam module inst, on page 1788• icam monitor scale, on page 1789• icam monitor scale, on page 1791• icmp-echo, on page 1792• icmpv6 cfs-queue, on page 1793• icmpv6 library mts-queue, on page 1794• icmpv6 mts-queue, on page 1795• import, on page 1796• import interface, on page 1797• import l2vpn evpn, on page 1798• import map, on page 1799• import running-config, on page 1800• import vpn unicast, on page 1801• import vrf default map, on page 1802• in-label allocate, on page 1803• inband-telemetry exporter, on page 1804• inband-telemetry flow-profile, on page 1805• inband-telemetry monitor, on page 1806• inband-telemetry queue-profile, on page 1807• inband-telemetry record, on page 1808• inband-telemetry system monitor, on page 1809• inband-telemetry watchlist ip, on page 1810• include-icv-indicator, on page 1811• include profile, on page 1812• include profile any, on page 1813• index next-label, on page 1814• index next, on page 1815• ingress-mtu, on page 1816• ingress-replication protocol bgp, on page 1817• ingress-replication protocol static, on page 1818• ingress, on page 1819
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1769
Page 1914
• ingress interface, on page 1820• ingress interface, on page 1821• inherit peer-policy, on page 1822• inherit peer-policy, on page 1823• inherit peer-session, on page 1824• inherit peer, on page 1825• inherit port-profile, on page 1826• initial-delay, on page 1827• initial-refresh skip, on page 1828• inject-map exist-map, on page 1829• innoshell, on page 1830• innoshell cmd, on page 1831• innoshell module, on page 1832• innoshell module cmd, on page 1833• install activate, on page 1834• install add, on page 1835• install all, on page 1836• install all network-os, on page 1837• install commit, on page 1838• install deactivate, on page 1839• install epld, on page 1840• install epld, on page 1841• install feature-set fcoe-npv, on page 1842• install license, on page 1843• install license, on page 1844• install remove, on page 1845• install reset, on page 1846• install verify, on page 1847• instance-id, on page 1848• instance, on page 1849• instance, on page 1850• instance vlan, on page 1851• interface, on page 1852• interface, on page 1853• interface, on page 1854• interface, on page 1855• interface, on page 1856• interface, on page 1857• interface, on page 1858• interface, on page 1859• interface, on page 1860• interface, on page 1861• interface, on page 1862• interface, on page 1863• interface, on page 1864• interface, on page 1865
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1770
I Commands
Page 1915
• interface, on page 1866• interface, on page 1867• interface, on page 1868• interface breakout-profile, on page 1869• interface breakout module, on page 1870• interface breakout module, on page 1871• interface breakout module port map, on page 1872• interface breakout module port map, on page 1873• interface down delay, on page 1874• interop-enable, on page 1875• interval, on page 1876• interval, on page 1877• ip, on page 1878• ip, on page 1879• ip, on page 1880• ip, on page 1881• ip, on page 1882• ip, on page 1883• ip, on page 1884• ip access-class, on page 1885• ip access-group, on page 1886• ip access-list, on page 1887• ip access-list match-local-traffic, on page 1888• ip address, on page 1889• ip address dhcp, on page 1890• ip address ipv6 address port, on page 1891• ip address secondary, on page 1892• ip adjacency peer-gmac, on page 1893• ip adjacency remote-adj, on page 1894• ip adjacency route distance, on page 1895• ip amt anycast-relay-prefix, on page 1896• ip amt gateway, on page 1897• ip amt join-policy, on page 1898• ip amt qqic, on page 1899• ip amt relay-advertisement-address, on page 1900• ip amt relay, on page 1901• ip amt state-limit, on page 1902• ip amt tunnel-limit, on page 1903• ip arp, on page 1904• ip arp allow-static-arp-outside-subnet, on page 1905• ip arp cache limit, on page 1906• ip arp cos, on page 1907• ip arp delete, on page 1908• ip arp event-history size, on page 1909• ip arp event-history size, on page 1911• ip arp evpn timeout, on page 1913
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1771
I Commands
Page 1916
• ip arp gratuitous hsrp duplicate, on page 1914• ip arp gratuitous request, on page 1915• ip arp gratuitous update, on page 1916• ip arp inspection filter vlan, on page 1917• ip arp inspection log-buffer entries, on page 1918• ip arp inspection trust, on page 1919• ip arp inspection validate, on page 1920• ip arp inspection vlan, on page 1921• ip arp off-list timeout, on page 1922• ip arp rarp fabric-forwarding, on page 1923• ip arp rarp fabric-forwarding, on page 1924• ip arp rarp fabric-forwarding rate-limit, on page 1925• ip arp suppression-cache, on page 1926• ip arp suppression timeout, on page 1927• ip arp synchronize, on page 1928• ip arp timeout, on page 1929• ip arp timeout, on page 1930• ip arp unnum-svi-dup-ip-detection, on page 1931• ip arp unnum-svi-sw-replication, on page 1932• ip as-path access-list deny, on page 1933• ip as-path access-list deny, on page 1934• ip as-path access-list seq deny, on page 1935• ip authentication, on page 1936• ip auto-discard, on page 1937• ip bandwidth-percent eigrp, on page 1938• ip bandwidth eigrp, on page 1939• ip community-list expanded deny, on page 1940• ip community-list expanded deny, on page 1941• ip community-list expanded seq deny, on page 1942• ip community-list standard permit internet local-AS, on page 1943• ip community-list standard permit internet local-AS, on page 1944• ip community-list standard seq permit internet local-AS, on page 1945• ip delay eigrp, on page 1946• ip destination, on page 1947• ip dhcp option82 suboption circuit-id, on page 1948• ip dhcp packet strict-validation, on page 1949• ip dhcp relay, on page 1950• ip dhcp relay address, on page 1951• ip dhcp relay information option, on page 1952• ip dhcp relay information option trust, on page 1953• ip dhcp relay information option vpn, on page 1954• ip dhcp relay information trust-all, on page 1955• ip dhcp relay information trusted, on page 1956• ip dhcp relay source-interface, on page 1957• ip dhcp relay source-interface, on page 1958• ip dhcp relay sub-option circuit-id customized, on page 1959
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1772
I Commands
Page 1917
• ip dhcp relay sub-option circuit-id format-type string, on page 1960• ip dhcp relay sub-option type cisco, on page 1961• ip dhcp smart-relay, on page 1962• ip dhcp smart-relay global, on page 1963• ip dhcp snooping, on page 1964• ip dhcp snooping information option, on page 1965• ip dhcp snooping ipsg-excluded vlan, on page 1966• ip dhcp snooping sub-option circuit-id format-type string, on page 1967• ip dhcp snooping trust, on page 1968• ip dhcp snooping verify mac-address, on page 1969• ip dhcp snooping vlan, on page 1970• ip directed-broadcast, on page 1971• ip distribute-list eigrp, on page 1972• ip dns source-interface, on page 1973• ip domain-list, on page 1974• ip domain-lookup, on page 1975• ip domain-name, on page 1976• ip drop-glean, on page 1977• ip dscp-lop, on page 1978• ip dscp, on page 1979• ip eigrp bfd, on page 1980• ip eigrp event-history bfd size, on page 1981• ip eigrp event-history errors, on page 1982• ip eigrp event-history size, on page 1983• ip eigrp shutdown, on page 1984• ip extcommunity-list expanded deny, on page 1985• ip extcommunity-list standard permit, on page 1986• ip fabric multicast file-debug, on page 1987• ip flow monitor input, on page 1988• ip flow monitor input, on page 1989• ip flow monitor input, on page 1990• ip forward, on page 1991• ip ftp source-interface, on page 1992• ip hello-interval eigrp, on page 1993• ip hold-time eigrp, on page 1994• ip host, on page 1995• ip host host, on page 1996• ip http source-interface, on page 1997• ip icmp-errors source-interface, on page 1998• ip igmp any-query-destination, on page 1999• ip igmp enforce-router-alert, on page 2000• ip igmp event-history cli, on page 2001• ip igmp event-history ha, on page 2002• ip igmp event-history interface, on page 2003• ip igmp event-history interface, on page 2004• ip igmp event-history mtrace, on page 2005
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1773
I Commands
Page 1918
• ip igmp event-history mvr, on page 2006• ip igmp event-history nbm, on page 2007• ip igmp event-history policy, on page 2008• ip igmp event-history vrf, on page 2009• ip igmp file-debug, on page 2010• ip igmp flush-routes, on page 2011• ip igmp group-timeout, on page 2012• ip igmp heavy-template, on page 2013• ip igmp host-proxy, on page 2014• ip igmp immediate-leave, on page 2015• ip igmp join-group, on page 2016• ip igmp last-member-query-count, on page 2017• ip igmp last-member-query-response-time, on page 2018• ip igmp querier-elect strict, on page 2019• ip igmp querier, on page 2020• ip igmp query-interval, on page 2021• ip igmp query-max-response-time, on page 2022• ip igmp report-link-local-groups, on page 2023• ip igmp report prefix-list, on page 2024• ip igmp robustness-variable, on page 2025• ip igmp snooping, on page 2026• ip igmp snooping, on page 2027• ip igmp snooping, on page 2028• ip igmp snooping access-group, on page 2029• ip igmp snooping disable-nve-static-router-port, on page 2030• ip igmp snooping disable-nve-static-router-port, on page 2031• ip igmp snooping event-history igmp-snoop-internal, on page 2032• ip igmp snooping event-history mfdm-sum, on page 2033• ip igmp snooping event-history mfdm, on page 2034• ip igmp snooping event-history rib, on page 2035• ip igmp snooping event-history vlan-events, on page 2036• ip igmp snooping event-history vlan, on page 2037• ip igmp snooping event-history vpc, on page 2038• ip igmp snooping group-timeout, on page 2039• ip igmp snooping group-timeout, on page 2040• ip igmp snooping last-member-query-interval, on page 2041• ip igmp snooping link-local-groups-suppression, on page 2042• ip igmp snooping link-local-groups-suppression, on page 2043• ip igmp snooping many-to-one-enhance, on page 2044• ip igmp snooping max-gq-miss, on page 2045• ip igmp snooping mrouter vpc-peer-link, on page 2046• ip igmp snooping proxy-leave use-group-address, on page 2047• ip igmp snooping proxy general-queries, on page 2048• ip igmp snooping proxy general-queries, on page 2049• ip igmp snooping report-flood all, on page 2050• ip igmp snooping report-suppression, on page 2051
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1774
I Commands
Page 1919
• ip igmp snooping report-suppression, on page 2052• ip igmp snooping report prefix interface, on page 2053• ip igmp snooping syslog-threshold, on page 2054• ip igmp snooping v3-report-suppression, on page 2055• ip igmp snooping v3-report-suppression, on page 2056• ip igmp spoof-check, on page 2057• ip igmp ssm-translate, on page 2058• ip igmp startup-query-count, on page 2059• ip igmp startup-query-interval, on page 2060• ip igmp state-limit, on page 2061• ip igmp static, on page 2062• ip igmp suppress v3-gsq, on page 2063• ip igmp syslog-threshold, on page 2064• ip igmp version, on page 2065• ip lisp alt-vrf, on page 2066• ip lisp database-mapping dynamic priority weight, on page 2067• ip lisp disable-spoof-alert, on page 2068• ip lisp etr, on page 2069• ip lisp etr accept-map-request-mapping, on page 2070• ip lisp etr glean-mapping, on page 2071• ip lisp etr map-cache-ttl, on page 2072• ip lisp etr map-register-ttl, on page 2073• ip lisp etr map-server key, on page 2074• ip lisp hardware-forwarding, on page 2075• ip lisp itr-etr, on page 2076• ip lisp itr, on page 2077• ip lisp itr map-resolver, on page 2078• ip lisp itr send-data-probe, on page 2079• ip lisp locator-vrf, on page 2080• ip lisp locator reachability exclude, on page 2081• ip lisp map-cache-limit, on page 2082• ip lisp map-cache drop native-forward map-request priority weight, on page 2083• ip lisp map-request-source, on page 2084• ip lisp map-resolver, on page 2085• ip lisp map-server, on page 2086• ip lisp map-server try-map-cache, on page 2087• ip lisp multicast, on page 2088• ip lisp nat-traversal, on page 2089• ip lisp ntr, on page 2090• ip lisp null0-is-alt-miss, on page 2091• ip lisp proxy-etr, on page 2092• ip lisp proxy-itr, on page 2093• ip lisp short-map-cache-ttl, on page 2094• ip lisp shortest-eid-prefix-length, on page 2095• ip lisp source-locator, on page 2096• ip lisp translate inside outside, on page 2097
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1775
I Commands
Page 1920
• ip lisp use-bgp-locators, on page 2098• ip lisp use-petr priority weight, on page 2099• ip load-sharing address, on page 2100• ip local-proxy-arp, on page 2101• ip local policy route-map, on page 2102• ip mfwd event-history cli, on page 2103• ip mfwd event-history l2, on page 2104• ip mfwd event-history nbm, on page 2105• ip mfwd event-history packet, on page 2106• ip mfwd event-history vrf, on page 2107• ip mfwd mstatic register, on page 2108• ip mroute, on page 2109• ip msdp description, on page 2110• ip msdp event-history cli, on page 2111• ip msdp event-history events, on page 2112• ip msdp event-history routes, on page 2113• ip msdp event-history tcp, on page 2114• ip msdp flush-routes, on page 2115• ip msdp group-limit source, on page 2116• ip msdp keepalive, on page 2117• ip msdp mesh-group, on page 2118• ip msdp originator-id, on page 2119• ip msdp password, on page 2120• ip msdp peer connect-source, on page 2121• ip msdp reconnect-interval, on page 2122• ip msdp redistribute, on page 2123• ip msdp sa-interval, on page 2124• ip msdp sa-limit, on page 2125• ip msdp sa-policy in, on page 2126• ip msdp sa-policy out, on page 2127• ip msdp shutdown, on page 2128• ip mtu eigrp, on page 2129• ip multicast multipath, on page 2130• ip multicast multipath resilient, on page 2131• ip multicast overlay-distributed-dr, on page 2132• ip multicast overlay-spt-only, on page 2133• ip multicast rpf select vrf group-list, on page 2134• ip name-server, on page 2135• ip nat inside, on page 2137• ip nat inside source, on page 2138• ip nat outside source, on page 2140• ip nat pool netmask, on page 2142• ip nat pool netmask, on page 2143• ip nat translation, on page 2144• ip nat translation creation-delay, on page 2145• ip nat translation max-entries, on page 2146
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1776
I Commands
Page 1921
• ip nat translation sampling-timeout, on page 2147• ip next-hop-self eigrp, on page 2148• ip offset-list eigrp, on page 2149• ip ospf advertise-subnet, on page 2150• ip ospf authentication-key, on page 2151• ip ospf authentication, on page 2152• ip ospf authentication key-chain, on page 2153• ip ospf bfd, on page 2154• ip ospf cost, on page 2155• ip ospf dead-interval, on page 2156• ZZZ_4621, on page 2157• ip ospf event-history cli, on page 2158• ip ospf event-history detail, on page 2159• ip ospf hello-interval, on page 2160• ip ospf message-digest-key md5, on page 2161• ip ospf mtu-ignore, on page 2162• ip ospf network broadcast, on page 2163• ip ospf network point-to-point, on page 2164• ip ospf passive-interface, on page 2165• ip ospf prefix-attributes n-flag-clear, on page 2166• ip ospf priority, on page 2167• ip ospf retransmit-interval, on page 2168• ip ospf shutdown, on page 2169• ip ospf transmit-delay, on page 2170• ip passive-interface eigrp, on page 2171• ip pim anycast-rp, on page 2172• ip pim assert-rate-limit, on page 2173• ip pim auto-enable, on page 2174• ip pim auto-rp listen, on page 2175• ip pim auto-rp mapping-agent-policy, on page 2176• ip pim auto-rp mapping-agent send-rp-discovery, on page 2177• ip pim auto-rp rp-candidate-policy, on page 2178• ip pim auto-rp rp-candidate send-rp-announce group-list route-map prefix-list, on page 2179• ip pim bfd-instance, on page 2180• ip pim bfd, on page 2181• ip pim bidir-rp-limit, on page 2182• ip pim border-router, on page 2183• ip pim border, on page 2184• ip pim bsr-candidate, on page 2185• ip pim bsr bsr-policy, on page 2186• ip pim bsr listen, on page 2187• ip pim bsr rp-candidate-policy, on page 2188• ip pim dr-delay, on page 2189• ip pim dr-priority, on page 2190• ip pim event-history assert, on page 2191• ip pim event-history bidir, on page 2192
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1777
I Commands
Page 1922
• ip pim event-history cli, on page 2193• ip pim event-history data-register-receive, on page 2194• ip pim event-history hello, on page 2195• ip pim event-history join-prune-summary, on page 2196• ip pim event-history join-prune-tw, on page 2197• ip pim event-history join-prune, on page 2198• ip pim event-history mrib, on page 2199• ip pim event-history mvpn, on page 2200• ip pim event-history nbm, on page 2201• ip pim event-history null-register, on page 2202• ip pim event-history packet, on page 2203• ip pim event-history pim-library, on page 2204• ip pim event-history rp, on page 2205• ip pim event-history txlist, on page 2206• ip pim event-history vpc, on page 2207• ip pim event-history vrf, on page 2208• ip pim evpn-border-leaf, on page 2209• ip pim extranet, on page 2210• ip pim file-debug, on page 2211• ip pim flush-routes, on page 2212• ip pim group-list, on page 2213• ip pim hello-authentication ah-md5, on page 2214• ip pim hello-interval, on page 2215• ip pim isolate, on page 2216• ip pim jp-interval, on page 2217• ip pim jp-policy, on page 2218• ip pim log-neighbor-changes, on page 2219• ip pim neighbor-policy prefix-list, on page 2220• ip pim passive, on page 2221• ip pim pre-build-spt, on page 2222• ip pim register-policy, on page 2223• ip pim register-rate-limit, on page 2224• ip pim register-source, on page 2225• ip pim register-until-stop, on page 2226• ip pim rp-address, on page 2227• ip pim rp-candidate group-list route-map prefix-list, on page 2228• ip pim sg-expiry-timer infinity, on page 2229• ip pim sparse-mode, on page 2230• ip pim ssm, on page 2231• ip pim state-limit, on page 2232• ip pim strict-rfc-compliant, on page 2233• ip pim strict-rfc-compliant, on page 2234• ip ping source-interface, on page 2235• ip policy match router-address, on page 2236• ip policy route-map, on page 2237• ip port-unreachable, on page 2238
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1778
I Commands
Page 1923
• ip port access-group, on page 2239• ip port access-group, on page 2240• ip prefix-list description, on page 2241• ip prefix-list permit, on page 2242• ip proxy-arp, on page 2243• ip radius source-interface, on page 2244• ip redirects, on page 2245• ip rip authentication key-chain, on page 2246• ip rip authentication mode text, on page 2247• ip rip metric, on page 2248• ip rip passive-interface, on page 2249• ip rip poison-reverse, on page 2250• ip rip route-filter route in, on page 2251• ip rip summary-address, on page 2252• ip route, on page 2253• ip route static bfd, on page 2254• ip router eigrp, on page 2255• ip router isis, on page 2256• ip router ospf area, on page 2257• ip router ospf multi-area, on page 2258• ip router rip, on page 2259• ip routing download-on-convergence, on page 2260• ip routing event-history, on page 2261• ip routing multicast event-history cli, on page 2262• ip routing multicast event-history mdt, on page 2263• ip routing multicast event-history mfdm-debugs, on page 2264• ip routing multicast event-history mfdm-events, on page 2265• ip routing multicast event-history mfdm-stats, on page 2266• ip routing multicast event-history nbm, on page 2267• ip routing multicast event-history notify-clients, on page 2268• ip routing multicast event-history rib-summary, on page 2269• ip routing multicast event-history rib, on page 2270• ip routing multicast event-history urib-debugs, on page 2271• ip routing multicast event-history vrf, on page 2272• ip routing multicast file-debug, on page 2273• ip routing multicast holddown, on page 2274• ip routing multicast mfdm-buffer-route-count, on page 2275• ip routing multicast software-replicate, on page 2276• ip routing multicast trace enable, on page 2277• ip routing multicast trace entries, on page 2278• ip routing multicast trace records, on page 2279• ip secondary, on page 2280• ip service-reflect destination to mask-len source, on page 2281• ip service-reflect mode regular, on page 2282• ip sla, on page 2283• ip sla group schedule, on page 2284
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1779
I Commands
Page 1924
• ip sla logging traps, on page 2286• ip sla reaction-configuration react, on page 2287• ip sla reaction-trigger, on page 2288• ip sla reset, on page 2289• ip sla responder, on page 2290• ip sla responder twamp, on page 2291• ip sla restart, on page 2292• ip sla schedule, on page 2293• ip sla server twamp, on page 2295• ip source-route, on page 2296• ip source binding vlan interface, on page 2297• ip source icmp-errors, on page 2298• ip split-horizon eigrp, on page 2299• ip ssh source-interface, on page 2300• ip summary-address eigrp ipv6 summary-address eigrp, on page 2301• ip tacacs source-interface, on page 2302• ip tcp mss, on page 2303• ip tcp path-mtu-discovery, on page 2304• ip tcp synwait-time, on page 2305• ip telnet source-interface, on page 2306• ip tftp source-interface, on page 2307• ip traceroute source-interface, on page 2308• ip ttl, on page 2309• ip udp relay addrgroup, on page 2310• ip udp relay subnet-broadcast, on page 2311• ip unnumbered, on page 2312• ip unreachables, on page 2313• ip verify source dhcp-snooping-vlan, on page 2314• ip verify unicast source reachable-via rx, on page 2315• ipv6, on page 2316• ipv6 access-class, on page 2318• ipv6 access-list, on page 2319• ipv6 access-list match-local-traffic, on page 2320• ipv6 address, on page 2321• ipv6 address dhcp, on page 2322• ipv6 address use-link-local-only, on page 2323• ipv6 adjacency-stale-timer, on page 2324• ipv6 adjacency route distance, on page 2325• ipv6 amt gateway, on page 2326• ipv6 amt relay, on page 2327• ipv6 destination, on page 2328• ipv6 dhcp-ldra, on page 2329• ipv6 dhcp-ldra attach-policy, on page 2330• ipv6 dhcp-ldra attach-policy vlan client, on page 2331• ipv6 dhcp guard, on page 2332• ipv6 dhcp guard, on page 2333
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1780
I Commands
Page 1925
• ipv6 dhcp guard policy, on page 2334• ipv6 dhcp relay, on page 2335• ipv6 dhcp relay address, on page 2336• ipv6 dhcp relay address ipv6 dhcp relay address, on page 2337• ipv6 dhcp relay option type cisco, on page 2338• ipv6 dhcp relay option vpn, on page 2339• ipv6 dhcp relay source-interface, on page 2340• ipv6 dhcp relay source-interface, on page 2341• ipv6 flow monitor input, on page 2342• ipv6 flow monitor input, on page 2343• ipv6 flow monitor input, on page 2344• ipv6 forward, on page 2345• ipv6 host, on page 2346• ipv6 link-local, on page 2347• ipv6 local policy route-map, on page 2348• ipv6 mld group-timeout, on page 2349• ipv6 mld immediate-leave, on page 2350• ipv6 mld join-group, on page 2351• ipv6 mld last-member-query-count, on page 2352• ipv6 mld last-member-query-response-time, on page 2353• ipv6 mld querier, on page 2354• ipv6 mld query-interval, on page 2355• ipv6 mld query-max-response-time, on page 2356• ipv6 mld report-link-local-groups, on page 2357• ipv6 mld report, on page 2358• ipv6 mld robustness-variable, on page 2359• ipv6 mld ssm-translate, on page 2360• ipv6 mld startup-query-count, on page 2361• ipv6 mld startup-query-interval, on page 2362• ipv6 mld state-limit, on page 2363• ipv6 mld static, on page 2364• ipv6 mld version, on page 2365• ipv6 nd cache limit, on page 2366• ipv6 nd dad attempts, on page 2367• ipv6 nd dadns-discover, on page 2368• ipv6 nd hop-limit, on page 2369• ipv6 nd mac-extract, on page 2370• ipv6 nd managed-config-flag, on page 2371• ipv6 nd mtu, on page 2372• ipv6 nd ns-interval, on page 2373• ipv6 nd off-list timeout, on page 2374• ipv6 nd other-config-flag, on page 2375• ipv6 nd prefix, on page 2376• ipv6 nd prefix default, on page 2377• ipv6 nd ra-interval, on page 2378• ipv6 nd ra-lifetime, on page 2379
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1781
I Commands
Page 1926
• ipv6 nd ra dns search-list sequence, on page 2380• ipv6 nd ra dns search-list suppress, on page 2381• ipv6 nd ra dns server sequence, on page 2382• ipv6 nd ra dns server suppress, on page 2383• ipv6 nd ra route suppress, on page 2384• ipv6 nd raguard, on page 2385• ipv6 nd raguard, on page 2386• ipv6 nd raguard attach-policy, on page 2387• ipv6 nd raguard policy, on page 2388• ipv6 nd reachable-time, on page 2389• ipv6 nd retrans-timer, on page 2390• ipv6 nd route route-preference High Low Medium infinite, on page 2391• ipv6 nd router-preference High Low Medium, on page 2392• ipv6 nd solicit-na accept, on page 2393• ipv6 nd suppress-ra, on page 2394• ipv6 nd synchronize, on page 2395• ipv6 neighbor, on page 2396• ipv6 neighbor allow-static-neighbor-outside-subnet, on page 2397• ipv6 neighbor binding, on page 2398• ipv6 neighbor binding, on page 2399• ipv6 neighbor binding logging, on page 2400• ipv6 neighbor binding max-entries, on page 2401• ipv6 neighbor tracking, on page 2402• ipv6 pim anycast-rp, on page 2403• ipv6 pim bidir-rp-limit, on page 2404• ipv6 pim border, on page 2405• ipv6 pim bsr-candidate, on page 2406• ipv6 pim bsr bsr-policy, on page 2407• ipv6 pim bsr listen, on page 2408• ipv6 pim bsr rp-candidate-policy, on page 2409• ipv6 pim dr-priority, on page 2410• ipv6 pim event-history assert-receive, on page 2411• ipv6 pim event-history bidir, on page 2412• ipv6 pim event-history hello, on page 2413• ipv6 pim event-history join-prune, on page 2414• ipv6 pim event-history null-register, on page 2415• ipv6 pim event-history packet, on page 2416• ipv6 pim event-history rp, on page 2417• ipv6 pim event-history vrf, on page 2418• ipv6 pim flush-routes, on page 2419• ipv6 pim hello-interval, on page 2420• ipv6 pim isolate, on page 2421• ipv6 pim jp-policy, on page 2422• ipv6 pim log-neighbor-changes, on page 2423• ipv6 pim neighbor-policy, on page 2424• ipv6 pim passive, on page 2425
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1782
I Commands
Page 1927
• ipv6 pim register-policy, on page 2426• ipv6 pim register-rate-limit, on page 2427• ipv6 pim rp-address, on page 2428• ipv6 pim rp-candidate group, on page 2429• ipv6 pim sparse-mode, on page 2430• ipv6 pim ssm, on page 2431• ipv6 pim state-limit, on page 2432• ipv6 pim use-shared-tree-only spt-threshold infinity group-list, on page 2433• ipv6 policy route-map, on page 2434• ipv6 port traffic-filter, on page 2435• ipv6 prefix-list description, on page 2436• ipv6 prefix-list permit, on page 2437• ipv6 queue-packets, on page 2438• ipv6 redirects, on page 2439• ipv6 route, on page 2440• ipv6 route static bfd, on page 2441• ipv6 router isis, on page 2442• ipv6 router ospfv3 area, on page 2443• ipv6 router ospfv3 multi-area, on page 2444• ipv6 routing event-history size, on page 2445• ipv6 routing multicast event-history cli, on page 2446• ipv6 routing multicast event-history mfdm-debugs, on page 2447• ipv6 routing multicast event-history mfdm-events, on page 2448• ipv6 routing multicast event-history mfdm-stats, on page 2449• ipv6 routing multicast event-history rib-summary, on page 2450• ipv6 routing multicast event-history rib, on page 2451• ipv6 routing multicast event-history vrf, on page 2452• ipv6 routing multicast holddown, on page 2453• ipv6 routing multicast software-replication, on page 2454• ipv6 snooping, on page 2455• ipv6 snooping, on page 2456• ipv6 snooping policy, on page 2457• ipv6 switch-packets, on page 2458• ipv6 traffic-filter, on page 2459• ipv6 unreachables, on page 2460• ipv6 verify unicast source reachable-via rx, on page 2461• is-type, on page 2462• ishow cli find nodes, on page 2463• ishow cli modes, on page 2464• ishow cli nodes, on page 2465• ishow cli paths, on page 2466• ishow cli tags, on page 2467• ishow core backtrace, on page 2468• isis authentication-check, on page 2469• isis authentication-check level-1, on page 2470• isis authentication-check level-2, on page 2471
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1783
I Commands
Page 1928
• isis authentication-type cleartext, on page 2472• isis authentication-type cleartext, on page 2473• isis authentication key-chain, on page 2474• isis authentication key-chain, on page 2475• isis bfd, on page 2476• isis circuit-type, on page 2477• isis csnp-interval level, on page 2478• isis event-history adjacency, on page 2479• isis event-history cli, on page 2480• isis event-history csnp, on page 2481• isis event-history dis, on page 2482• isis event-history events, on page 2483• isis event-history graceful, on page 2484• isis event-history ha, on page 2485• isis event-history iih, on page 2486• isis event-history lsp-flood, on page 2487• isis event-history lsp-gen, on page 2488• isis event-history mtr, on page 2489• isis event-history perf, on page 2490• isis event-history psnp, on page 2491• isis event-history redist, on page 2492• isis event-history spf-leaf, on page 2493• isis event-history spf-tree, on page 2494• isis event-history sr, on page 2495• isis event-history tlv, on page 2496• isis event-history ulib, on page 2497• isis event-history urib, on page 2498• isis hello-interval, on page 2499• isis hello-interval level, on page 2500• isis hello-multiplier, on page 2501• isis hello-multiplier level, on page 2502• isis hello-padding, on page 2503• isis ipv6 bfd, on page 2504• isis ipv6 metric, on page 2505• isis lsp-interval, on page 2506• isis mesh-group, on page 2507• isis metric, on page 2508• isis mtu-check, on page 2509• isis mtu-check level, on page 2510• isis network point-to-point, on page 2511• isis passive-interface, on page 2512• isis prefix-attributes n-flag-clear, on page 2513• isis priority level, on page 2514• isis retransmit-interval, on page 2515• isis retransmit-throttle-interval, on page 2516• isis shutdown, on page 2517
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1784
I Commands
Page 1929
• isolate, on page 2518• isolate, on page 2519• isolate, on page 2520• isolate, on page 2521• isolate, on page 2522• isolate, on page 2523• isolate, on page 2524• itd, on page 2525• itd device-group, on page 2526• itd session access-list refresh, on page 2527• itd session device-group, on page 2528• itd statistics, on page 2529
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1785
I Commands
Page 1930
icam monitor entries acl module inst[no] icam monitor entries acl module <module> inst <inst>
Syntax Description
(Optional) Negate a command or set its defaultsno
intelligent CAMicam
icam monitormonitor
icam monitor entries statsentries
icam monitor entries type ACLacl
Module Numbermodule
Enter Module Numbermodule
ASIC/Forwarding Engine Instance Numberinst
Enter Instance Numberinst
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1786
I Commandsicam monitor entries acl module inst
Page 1931
icam monitor interval num_intervals[no] icam monitor interval <interval-hours> num_intervals <number-of-intervals>
Syntax Description
(Optional) Negate a command or set its defaultsno
intelligent CAMicam
icam monitormonitor
icam monitor intervalinterval
icam monitor interval in hoursinterval-hours
icam monitor historynum_intervals
number of intervals to keep in icam monitor historynumber-of-intervals
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1787
I Commandsicam monitor interval num_intervals
Page 1932
icam monitor resource acl_tcam module inst[no] icam monitor resource { acl_tcam | fib_tcam } module <module> inst <inst>
Syntax Description
(Optional) Negate a command or set its defaultsno
intelligent CAMicam
icam monitormonitor
icam monitor resource utilizationresource
icam monitor resource type ACL TCAMacl_tcam
icam monitor resource type FIB TCAMfib_tcam
Module Numbermodule
Enter Module Numbermodule
ASIC/Forwarding Engine Instance Numberinst
Enter Instance Numberinst
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1788
I Commandsicam monitor resource acl_tcam module inst
Page 1933
icam monitor scale[no] icam monitor scale { { threshold info <ithres> warning <wthres> critical <cthres> } | { { { l2-switching{ mac-addresses | mst-instances | mst-vports | rpvst-vports | rpvst-vlans | total-vlans-x-ports | vlans } } | {multicast-routing {multicast-routes | igmp-groups | pim-neighbors | outgoing-interfaces } } | { unicast-routing{ bfd-sessions | eigrp-routes | ipv4-arp | ipv4-host-routes | ipv6-host-routes | ipv4-isis-routes | ospf-nbr | ospf-lsa| ospf-area | ospf-vrf | ospf-passive-intf } } | { vxlan { test } } } limit <nlimit> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
intelligent CAMicam
icam monitormonitor
icam monitor scalescale
Layer 2 switchingl2-switching
Multicast routingmulticast-routing
Unicast routingunicast-routing
VxLANvxlan
MAC addressesmac-addresses
MST instancesmst-instances
MST virtual portsmst-vports
RPVST virtual portsrpvst-vports
RPVST VLANsrpvst-vlans
Total number of VLANs x ports with switchport isolatedtotal-vlans-x-ports
VLANsvlans
Multicast routesmulticast-routes
IGMP groupsigmp-groups
PIM neighborspim-neighbors
Outgoing interfacesoutgoing-interfaces
BFD sessionsbfd-sessions
EIGRP routeseigrp-routes
IPv4 ARPipv4-arp
IPv4 host routesipv4-host-routes
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1789
I Commandsicam monitor scale
Page 1934
IPv6 host routesipv6-host-routes
IPv4 IS-IS routesipv4-isis-routes
OSPF neighborsospf-nbr
OSPF LSAsospf-lsa
OSPF Areasospf-area
OSPF VRFsospf-vrf
OSPF passive interfacesospf-passive-intf
VxLAN testtest
Change feature limitlimit
New feature limitnlimit
Change percent threshold limitthreshold
Info thresholdinfo
Info threshold percentithres
Warning thresholdwarning
Warning threshold percentwthres
Critical thresholdcritical
Critical threshold percentcthres
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1790
I Commandsicam monitor scale
Page 1935
icam monitor scale[no] icam monitor scale
Syntax Description
(Optional) Negate a command or set its defaultsno
intelligent CAMicam
icam monitormonitor
icam monitor scalescale
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1791
I Commandsicam monitor scale
Page 1936
icmp-echo[no] icmp-echo { <hostname> | <ip-address> | <ipv6-address> } { [ source-ip { <source-ip-hostname> |<source-ip-address> | <source-ipv6-address> } ] | [ source-interface <if_index> ] }
Syntax Description
(Optional)no
(Optional) source-interfacesource-ip
ICMP Echo Operationicmp-echo
Destination hostname, broadcast disallowedhostname
Destination IP address, broadcast disallowedip-address
(Optional) Source Interface (ingress icmp packet interface)source-interface
(Optional) Source Interfaceif_index
(Optional) source IP hostname, broadcast disallowedsource-ip-hostname
(Optional) source IP address, broadcast disallowedsource-ip-address
Command Mode
• /exec/configure/ip-sla
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1792
I Commandsicmp-echo
Page 1937
icmpv6 cfs-queue{ icmpv6 cfs-queue <size> } | { no icmpv6 cfs-queue }
Syntax Description
Negate a command or set its defaultsno
ICMPv6 Commandsicmpv6
cfs-queuecfs-queue
Size for adjacencies to be sent in CFSoE payloadsize
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1793
I Commandsicmpv6 cfs-queue
Page 1938
icmpv6 library mts-queue{ icmpv6 library mts-queue <size> } | { no icmpv6 library mts-queue }
Syntax Description
Negate a command or set its defaultsno
ICMPv6 Commandsicmpv6
library data queuelibrary
mts-queuemts-queue
Size for icmpv6 data sap qlimitsize
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1794
I Commandsicmpv6 library mts-queue
Page 1939
icmpv6 mts-queue{ icmpv6 mts-queue <size> } | { no icmpv6 mts-queue }
Syntax Description
Negate a command or set its defaultsno
ICMPv6 Commandsicmpv6
mts-queuemts-queue
Size for icmpv6 data sap qlimitsize
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1795
I Commandsicmpv6 mts-queue
Page 1940
importimport
Syntax Description
importimport
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1796
I Commandsimport
Page 1941
import interfaceimport interface <if0>
Syntax Description
importimport
Interface configurationinterface
interface type and number in module/slot formatif0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1797
I Commandsimport interface
Page 1942
import l2vpn evpn[ no | default ] import l2vpn evpn [ route-map <import-map> ] [ reoriginate ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Import the routes into another AFimport
L2VPNl2vpn
EVPNevpn
(Optional) Reoriginate the route with new RTreoriginate
(Optional) Apply route-map to specify import criteriaroute-map
(Optional) Route-map nameimport-map
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1798
I Commandsimport l2vpn evpn
Page 1943
import map[no] import map <rmap-name> [ evpn ]
Syntax Description
(Optional) Negate a command or set its defaultsno
VRF importimport
Route-map based VRF importmap
Route-map namermap-name
(Optional) EVPNevpn
Command Mode
• /exec/configure/vrf-af-ipv4 /exec/configure/vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1799
I Commandsimport map
Page 1944
import running-configimport running-config [ exclude interface ethernet ]
Syntax Description
importimport
running-configrunning-config
(Optional) Excludeexclude
(Optional) Exclude all interfaces of this typeinterface
(Optional) running-config excluding physical interfacesethernet
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1800
I Commandsimport running-config
Page 1945
import vpn unicast[ no | default ] import vpn unicast [ route-map <import-map> ] [ reoriginate ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Import the routes into another AFimport
L3VPNvpn
unicastunicast
(Optional) Reoriginate the route with new RTreoriginate
(Optional) Apply route-map to specify import criteriaroute-map
(Optional) Route-map nameimport-map
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1801
I Commandsimport vpn unicast
Page 1946
import vrf default mapimport vrf default [ <prefix-limit> ] map <rmap-name> | no import vrf default [ <prefix-limit> ] map<rmap-name>
Syntax Description
Negate a command or set its defaultsno
VRF importimport
Virtual Router Contextvrf
VRF name (default)default
(Optional) Maximum prefix limitprefix-limit
Route-map based VRF importmap
Route-map namermap-name
Command Mode
• /exec/configure/vrf-af-ipv4 /exec/configure/vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1802
I Commandsimport vrf default map
Page 1947
in-label allocate[no] in-label <static-inlabel> allocate [ policy { <prefix> <mask> | <prefix-mask> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure local label assignment and forwarding for the LSPin-label
Allocate this labelallocate
(Optional) Allocate policy-based IP prefixpolicy
Label Valuestatic-inlabel
(Optional) Destination prefixprefix
(Optional) Destination prefix maskmask
(Optional) Destination prefix/maskprefix-mask
Command Mode
• /exec/configure/mpls_static/ipv4/lsp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1803
I Commandsin-label allocate
Page 1948
inband-telemetry exporter[no] inband-telemetry exporter <exportername>
Syntax Description
Enable/Disable inband telemetry configurationinband-telemetry
Define a events Exporterexporter
Name of event Exporterexportername
Command Mode
• /exec/configure/config-int
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1804
I Commandsinband-telemetry exporter
Page 1949
inband-telemetry flow-profile[no] inband-telemetry flow-profile
Syntax Description
Enable/Disable inband telemetry configurationinband-telemetry
Define a INT flow-profileflow-profile
Command Mode
• /exec/configure/config-int
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1805
I Commandsinband-telemetry flow-profile
Page 1950
inband-telemetry monitor[no] inband-telemetry monitor <monitorname>
Syntax Description
Enable/Disable inband telemetry configurationinband-telemetry
Define a INT Monitormonitor
Name of INT Monitormonitorname
Command Mode
• /exec/configure/config-int
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1806
I Commandsinband-telemetry monitor
Page 1951
inband-telemetry queue-profile[no] inband-telemetry queue-profile [ <queue_profilename> | queue-profile-default ]
Syntax Description
Enable/Disable inband telemetry configurationinband-telemetry
Define a INT queue_profilequeue-profile
(Optional) Name of INT queue_profilequeue_profilename
(Optional) Queue Profile Default Configurationqueue-profile-default
Command Mode
• /exec/configure/config-int
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1807
I Commandsinband-telemetry queue-profile
Page 1952
inband-telemetry record[no] inband-telemetry record <recordname>
Syntax Description
Enable/Disable inband telemetry configurationinband-telemetry
Define a INT Recordrecord
Record namerecordname
Command Mode
• /exec/configure/config-int
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1808
I Commandsinband-telemetry record
Page 1953
inband-telemetry system monitor[no] inband-telemetry system monitor <monitorname>
Syntax Description
global configsystem
int global settingsinband-telemetry
int Monitor to be appliedmonitor
int Monitor to be appliedmonitorname
Command Mode
• /exec/configure/config-int
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1809
I Commandsinband-telemetry system monitor
Page 1954
inband-telemetry watchlist ip[no] inband-telemetry watchlist ip <watchlistname>
Syntax Description
Enable/Disable inband telemetry configurationinband-telemetry
Define a INT watchlistwatchlist
Configure INT IP watchlistip
Name of INT watchlistwatchlistname
Command Mode
• /exec/configure/config-int
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1810
I Commandsinband-telemetry watchlist ip
Page 1955
include-icv-indicator[no] include-icv-indicator
Syntax Description
Include ICV Indicator paramset in MKPDUinclude-icv-indicator
Command Mode
• /exec/configure/macsec-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1811
I Commandsinclude-icv-indicator
Page 1956
include profile[no] include profile { <all_conf_profile_name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Include a port-profileinclude
config-profileprofile
Enter the name of the profileall_conf_profile_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1812
I Commandsinclude profile
Page 1957
include profile any[no] include profile any
Syntax Description
(Optional) Negate a command or set its defaultsno
Include a port-profileinclude
config-profileprofile
dynamically include profile during applyany
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1813
I Commandsinclude profile any
Page 1958
index next-label{ no index <idx> | index<idx> next-label <lbl> }
Syntax Description
Negate a command or set its defaultsno
Next entry indexindex
Index numberidx
Label Configurationnext-label
MPLS Label valuelbl
Command Mode
• /exec/configure/sr/te/exp_path
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1814
I Commandsindex next-label
Page 1959
index next{ { index <index> { next-address [ loose | strict ] <ipaddr> | exclude-address <ipaddr> } } | { no index <index>} }
Syntax Description
Negate a command or set its defaultsno
Specify the next entry index to add, edit (or delete)index
Previous index numberindex
Specify the next address in the pathnext-address
(Optional) Target address is looseloose
(Optional) Target address is strictstrict
Exclude an address from subsequent partial path segmentsexclude-address
Enter IP address (A.B.C.D)ipaddr
Command Mode
• /exec/configure/te/expl-path
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1815
I Commandsindex next
Page 1960
ingress-mtuingress-mtu <mtu_value> | no ingress-mtu
Syntax Description
Negate the commandno
set/reset ingress port mtu valueingress-mtu
mtu valuemtu_value
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet handle auto 424
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1816
I Commandsingress-mtu
Page 1961
ingress-replication protocol bgp[no] ingress-replication protocol bgp
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure ingress replicationingress-replication
Control protocol to useprotocol
Border Gateway Protocolbgp
Command Mode
• /exec/configure/if-nve/vni
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1817
I Commandsingress-replication protocol bgp
Page 1962
ingress-replication protocol static[no] ingress-replication protocol static
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure ingress replicationingress-replication
Control protocol to useprotocol
Static End-point Configurationstatic
Command Mode
• /exec/configure/if-nve/vni
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1818
I Commandsingress-replication protocol static
Page 1963
ingress{ ingress <ifh> | no ingress }
Syntax Description
Negate a command or set its defaultsno
Ingress interface to determine enhanced forwarding enabledingress
Name of the interface for ngoam on which fabric forwarding isconfigured
ifh
Command Mode
• /exec/configure/configngoamprofile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1819
I Commandsingress
Page 1964
ingress interface[no] ingress interface <interface-ref> [ next-hop <ip-addr> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD ingress interfaceingress
ITD ingress interfaceinterface
interface-ref
(Optional) next hop ip addressnext-hop
(Optional) Next hop IPv4 address connected to ingress intrerfaceip-addr
Command Mode
• /exec/configure/itd /exec/configure/itd-inout
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1820
I Commandsingress interface
Page 1965
ingress interface[no] ingress interface <interface-ref> [ next-hop <ip-addr> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure ingress interface for PLB serviceingress
Ingress interfaceinterface
interface-ref
(Optional) next hop ip addressnext-hop
(Optional) Next hop IPv4 address connected to ingress intrerfaceip-addr
Command Mode
• /exec/configure/plb /exec/configure/plb-inout
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1821
I Commandsingress interface
Page 1966
inherit peer-policy[no] inherit peer-policy <peer-policy-template-name> <policy-preference>
Syntax Description
(Optional) Negate a command or set its defaultsno
Inherit a templateinherit
Inherit a peer-policy templatepeer-policy
Template namepeer-policy-template-name
Sequence numberpolicy-preference
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1822
I Commandsinherit peer-policy
Page 1967
inherit peer-policy[no] inherit peer-policy <peer-policy-template-name> <policy-preference>
Syntax Description
(Optional) Negate a command or set its defaultsno
Inherit a templateinherit
Inherit a peer-policy templatepeer-policy
Template namepeer-policy-template-name
Sequence numberpolicy-preference
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-link-state/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1823
I Commandsinherit peer-policy
Page 1968
inherit peer-session[no] inherit peer-session <peer-session-template-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Inherit a templateinherit
Inherit a peer-session templatepeer-session
Template namepeer-session-template-name
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1824
I Commandsinherit peer-session
Page 1969
inherit peer[no] inherit peer <peer-template-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Inherit a templateinherit
Inherit a peer templatepeer
Peer template namepeer-template-name
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-vrf-neighbor/exec/configure/router-bgp/router-bgp-prefixneighbor/exec/configure/router-bgp/router-bgp-vrf-prefixneighbor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1825
I Commandsinherit peer
Page 1970
inherit port-profile[no] inherit port-profile { <s0> | <s1> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Inherit a port-profileinherit
Inherit a port-profileport-profile
Enter the name of the profiles0
Enter the name of the profiles1
Command Mode
• /exec/configure/if-any /exec/configure/if-port-channel exec/configure/if-port-channel-range/exec/configure/if-ethernet-m /exec/configure/if-ethernet-switch-m /exec/configure/if-te/exec/configure/if-pseudowire
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1826
I Commandsinherit port-profile
Page 1971
initial-delay[no] initial-delay <time-in-sec>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure delay interval to connect to the BMP serverinitial-delay
Delay valuetime-in-sec
Command Mode
• /exec/configure/router-bgp/router-bgp-bmp-server
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1827
I Commandsinitial-delay
Page 1972
initial-refresh skip[no] initial-refresh { skip | delay <time-in-sec> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure initial-refresh for the BMP serverinitial-refresh
Skip sending the initial route update to the BMP serverskip
Delay after which the initial route update is sent to the BMP serverdelay
Delay valuetime-in-sec
Command Mode
• /exec/configure/router-bgp/router-bgp-bmp-server
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1828
I Commandsinitial-refresh skip
Page 1973
inject-map exist-map[no] inject-map <inject-map-name> exist-map <exist-map-name> [ copy-attributes ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Routemap which specifies prefixes to injectinject-map
Route-map nameinject-map-name
Routemap which specifies exist conditionexist-map
Route-map nameexist-map-name
(Optional) Copy attributes from aggregatecopy-attributes
Command Mode
• /exec/configure/router-bgp/router-bgp-af
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1829
I Commandsinject-map exist-map
Page 1974
innoshellinnoshell
Syntax Description
innoshellinnoshell
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1830
I Commandsinnoshell
Page 1975
innoshell cmdinnoshell cmd <cmd>
Syntax Description
innoshellinnoshell
Specify commandcmd
Quoted commands to be execcmd
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1831
I Commandsinnoshell cmd
Page 1976
innoshell moduleinnoshell module <module>
Syntax Description
innoshellinnoshell
Select modulemodule
Module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1832
I Commandsinnoshell module
Page 1977
innoshell module cmdinnoshell module <module> cmd <cmd>
Syntax Description
innoshellinnoshell
Select modulemodule
Specify commandcmd
Module numbermodule
Quoted commands to be execcmd
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1833
I Commandsinnoshell module cmd
Page 1978
install activateinstall activate <patch> + [ forced ]
Syntax Description
Install packageinstall
Activate packageactivate
Package Namepatch
(Optional) non-interactiveforced
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1834
I Commandsinstall activate
Page 1979
install addinstall add { <package-name> | <uri1> } [ vrf <vrf-known-name> ] [ { gpg-key | [ activate [ upgrade | downgrade] ] [ forced ] } ]
Syntax Description
Install packageinstall
Add packageadd
Package namepackage-name
Enter package uriuri1
(Optional) Display per-VRF informationvrf
(Optional) Known VRF namevrf-known-name
(Optional) GPG-KEYgpg-key
(Optional) Activate packageactivate
(Optional) non-interactiveforced
(Optional) Upgrade packageupgrade
(Optional) Downgrade packagedowngrade
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1835
I Commandsinstall add
Page 1980
install allinstall { all [ nxos <uri> | kickstart <uri1> | system <uri3> | serial | ignore-script-errors ] + [ force ] [non-disruptive | no-reload | noswitchover ] [ bios | no-save ] [ bios-force ] [ non-interruptive ] [ compact ] |force-all [ nxos <uri> | serial | ignore-script-errors ] + [ non-disruptive ] [ force ] }
Syntax Description
upgrade softwareinstall
Upgrade the systemall
(Optional) Ignore script errors from dynamic confcheckignore-script-errors
(Optional) boot-variable namekickstart
(Optional) Enter image uriuri1
(Optional) boot-variable namesystem
(Optional) Enter image uriuri3
(Optional) Exit right before reload during install.no-reload
(Optional) Exit right before reload during install.noswitchover
(Optional) Non-Interruptive install.non-interruptive
(Optional) Config not saved.Manually save config before starting installall
no-save
(Optional) BIOS Onlybios
(Optional) Forcefully upgrade bios.bios-force
(Optional) Forcefully allow ISSU with target image .force
(Optional) Non-Disruptive install.non-disruptive
(Optional) Compact image to make it nexus 3k onlycompact
(Optional) boot-variable namenxos
(Optional) Enter image uriuri
(Optional) Upgrade linecards in serialserial
Force upgrade the systemforce-all
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1836
I Commandsinstall all
Page 1981
install all network-osinstall all network-os <uri>
Syntax Description
upgrade softwareinstall
Upgrade the systemall
non-cisco OSnetwork-os
Enter image uriuri
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1837
I Commandsinstall all network-os
Page 1982
install commitinstall commit [ <patch> ]
Syntax Description
Install packageinstall
Commit software patchcommit
(Optional) Package Namepatch
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1838
I Commandsinstall commit
Page 1983
install deactivateinstall deactivate <patch> + [ forced ]
Syntax Description
Install packageinstall
Deactivate packagedeactivate
Package Name[Note: startup configuration may get affected]patch
(Optional) non-interactiveforced
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1839
I Commandsinstall deactivate
Page 1984
install epldinstall epld <uri1> { { module { <module> | all } { primary | golden } [ force ] } }
Syntax Description
upgrade softwareinstall
Install EPLD from EPLD imageepld
Local URI containing EPLD Imageuri1
Enter the module number or module rangemodule
x or x-ymodule
Install all the modulesall
Upgrade primary fpga imageprimary
Upgrade golden fpga imagegolden
(Optional) Force Install EPLD from EPLD imageforce
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1840
I Commandsinstall epld
Page 1985
install epldinstall epld <uri1> { { module { <module> | all } [ force ] } }
Syntax Description
upgrade softwareinstall
Install EPLD from EPLD imageepld
Local URI containing EPLD Imageuri1
Enter the module number or module rangemodule
x or x-ymodule
Install all the modulesall
(Optional) Force Install EPLD from EPLD imageforce
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1841
I Commandsinstall epld
Page 1986
install feature-set fcoe-npv[no] install feature-set fcoe-npv
Syntax Description
(Optional) Negate a command or set its defaultsno
install a feature-setinstall
install feature-setfeature-set
FCOE-NPVfcoe-npv
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1842
I Commandsinstall feature-set fcoe-npv
Page 1987
install licenseinstall license <uri0> [ <s0> ] [ format ]
Syntax Description
upgrade softwareinstall
install licenselicense
Specify URL for license fileuri0
(Optional) Specify a target name for the license files0
(Optional) Reformat the license file to remove invalid characters andformatting
format
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1843
I Commandsinstall license
Page 1988
install licenseinstall license <uri0> [ <s0> ]
Syntax Description
upgrade softwareinstall
install licenselicense
Specify URL for license fileuri0
(Optional) Specify a target name for the license files0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1844
I Commandsinstall license
Page 1989
install removeinstall remove { <patch> | inactive } [ forced ]
Syntax Description
Install packageinstall
Remove packageremove
Package Namepatch
All inactive except non-committed packagesinactive
(Optional) Remove packageforced
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1845
I Commandsinstall remove
Page 1990
install resetinstall reset [ nxos { base | full } ]
Syntax Description
Install packageinstall
Reload nxos with default packagesreset
(Optional) Reloading with basenxos from fullnxos and vice-versanxos
(Optional) Reload with basenxos after resetingbase
(Optional) Reload with fullnxos after resetingfull
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1846
I Commandsinstall reset
Page 1991
install verifyinstall verify { <uri1> | package <patch> }
Syntax Description
Install packageinstall
Verify package for signatureverify
Enter package uriuri1
Enter active/inactive packagepackage
Package Namepatch
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1847
I Commandsinstall verify
Page 1992
instance-id[no] instance-id <iid>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configures Instance-ID for global data-mappingsinstance-id
24-bit instance-ID valueiid
Command Mode
• /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1848
I Commandsinstance-id
Page 1993
instance[no] instance <plistinst> [ cross-check ] | instance <plistinst>
Syntax Description
Negate a command or set its defaultsno
Configure a parameter list instanceinstance
Enter the name of the parameter list instanceplistinst
(Optional) Explicitly search for referencing config profilecross-check
Command Mode
• /exec/configure/param-list
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1849
I Commandsinstance
Page 1994
instance[no] instance <instance-id> [ vlan <vlan-list> ]
Syntax Description
Negate a command or set its defaultsno
Map vlans to an MST instanceinstance
MST instance idinstance-id
(Optional) Range of vlans to add to the instance mappingvlan
(Optional) vlan range ex: 1-65, 72, 200 - 300vlan-list
Command Mode
• /exec/configure/spanning-tree/mst/configuration
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1850
I Commandsinstance
Page 1995
instance vlaninstance <instance-id> vlan <vlan-list>
Syntax Description
Map vlans to an MST instanceinstance
MST instance idinstance-id
Range of vlans to add to the instance mappingvlan
vlan range ex: 1-65, 72, 200 - 300vlan-list
Command Mode
• /exec/configure/spanning-tree/mst/configuration
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1851
I Commandsinstance vlan
Page 1996
interface[no] interface <if_list> { [ qos-group <ucastqos-grp> ] }
Syntax Description
(Optional) Negate the commandno
Configure capture-scope parametersinterface
List of interfacesif_list
(Optional) Specify qos-group to be associatedqos-group
(Optional) Value 0-7ucastqos-grp
Command Mode
• /exec/configure/pkt-drop/profile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1852
I Commandsinterface
Page 1997
interface[no] interface <interface-ref>
Syntax Description
(Optional) Negate a command or set its defaultsno
egress interfaceinterface
interface-ref
Command Mode
• /exec/configure/catena-port-grp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1853
I Commandsinterface
Page 1998
interface[no] interface <interface-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Applied interfaceinterface
Name of interfaceinterface-id
Command Mode
• /exec/configure/static-host/dot1q /exec/configure/static-host/vni
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1854
I Commandsinterface
Page 1999
interface[no] interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure interfacesinterface
Interface Nameinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1855
I Commandsinterface
Page 2000
interface[no] interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure interfacesinterface
Interface Nameinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1856
I Commandsinterface
Page 2001
interface[no] interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure interfacesinterface
Interface Nameinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1857
I Commandsinterface
Page 2002
interface[no] interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure interfacesinterface
Interface Nameinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1858
I Commandsinterface
Page 2003
interface[no] interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure interfacesinterface
Interface Nameinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1859
I Commandsinterface
Page 2004
interface[no] interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure interfacesinterface
Interface Nameinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1860
I Commandsinterface
Page 2005
interface[no] interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure interfacesinterface
Interface Nameinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1861
I Commandsinterface
Page 2006
interface[no] interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure interfacesinterface
Interface Nameinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1862
I Commandsinterface
Page 2007
interfaceinterface <interface>
Syntax Description
Configure interfacesinterface
Interface Nameinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1863
I Commandsinterface
Page 2008
interface[no] interface <interface>
Syntax Description
Negate a command or set its defaultsno
Configure interfacesinterface
Interface Nameinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1864
I Commandsinterface
Page 2009
interface[no] interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure interfacesinterface
Interface Nameinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1865
I Commandsinterface
Page 2010
interface[no] interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure interfacesinterface
Interface Nameinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1866
I Commandsinterface
Page 2011
interface[no] interface <interface-ref>
Syntax Description
(Optional) Negate a command or set its defaultsno
egress interfaceinterface
interface-ref
Command Mode
• /exec/configure/itd-port-grp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1867
I Commandsinterface
Page 2012
interface{ interface <interface-range> } | { no interface }
Syntax Description
Negate a command or set its defaultsno
Configure ngoam egress interfaceinterface
Configure ngoam egress interfaceinterface-range
Command Mode
• /exec/configure/configngoamprofile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1868
I Commandsinterface
Page 2013
interface breakout-profileinterface breakout-profile <profile> | no interface breakout-profile [ <profile> ]
Syntax Description
Negate a command or set its defaultsno
Configure interfacesinterface
Configure breakout-profilebreakout-profile
Breakout Profileprofile
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1869
I Commandsinterface breakout-profile
Page 2014
interface breakout moduleinterface breakout module <lem-aware-module> [ map <breakout_map> ]
Syntax Description
Configure interfacesinterface
Configuring the breakout for a modulebreakout
High Bandwidth Modulemodule
High Bandwidth Module numberlem-aware-module
(Optional) Breakout Mapmap
(Optional) Breakout Map to be applied to all the ports in this modulebreakout_map
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1870
I Commandsinterface breakout module
Page 2015
interface breakout module[no] interface breakout module <lem-aware-module> [ map <breakout_map> ]
Syntax Description
Negate a command or set its defaultsno
Configure interfacesinterface
Configuring the breakout for a modulebreakout
High Bandwidth Modulemodule
High Bandwidth Module numberlem-aware-module
(Optional) Breakout Mapmap
(Optional) Breakout Map to be applied to all the ports in this modulebreakout_map
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1871
I Commandsinterface breakout module
Page 2016
interface breakout module port map[no] interface breakout module <lem-aware-module> port <port_num> map <breakout_map>
Syntax Description
Negate a command or set its defaultsno
Configure interfacesinterface
Configuring the breakout for an interfacebreakout
High Bandwidth Modulemodule
High Bandwidth Module numberlem-aware-module
High Bandwidth Port(HBP)port
Parent(HBP / Front-panel) port to be broken outport_num
Breakout Mapmap
Breakout Map to be applied to the parent portbreakout_map
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1872
I Commandsinterface breakout module port map
Page 2017
interface breakout module port mapinterface breakout module <lem-aware-module> port <port_num> map <breakout_map>
Syntax Description
Configure interfacesinterface
ConfigurinG the breakout for an interfacebreakout
High Bandwidth Modulemodule
High Bandwidth Module numberlem-aware-module
High Bandwidth Port(HBP)port
Parent(HBP / Front-panel) port to be broken outport_num
Breakout Mapmap
Breakout Map to be applied to the parent portbreakout_map
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1873
I Commandsinterface breakout module port map
Page 2018
interface down delay[no] interface down delay |
Syntax Description
delaydown
Negate a command or set its defaultsno
Add tunnel interface configinterface
Tunnel interface down delay configdelay
Command Mode
• /exec/configure/if-te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1874
I Commandsinterface down delay
Page 2019
interop-enable[no] interop-enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable interoperability with IOS XR boxes in the networkinterop-enable
Command Mode
• /exec/configure/otv-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1875
I Commandsinterop-enable
Page 2020
interval[no] interval <timeinterval>
Syntax Description
Time interval to be configuredinterval
time interval in increments of 100mstimeinterval
Command Mode
• /exec/configure/config-ssx-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1876
I Commandsinterval
Page 2021
interval{ interval <interval> }
Syntax Description
Waitinterval
Intervalinterval
Command Mode
• /exec/configure/configngoamconnectcheck
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1877
I Commandsinterval
Page 2022
ip{ [ no ] <seqnum> <permitdeny> { ip { <src_prefix> | <src_any> } { <dst_prefix> | <dst_any> } } } | { no<seqnum> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Sequence numberseqnum
ipip
permitdenypermitdeny
A.B.C.D/nn Source network prefixsrc_prefix
Any source addresssrc_any
A.B.C.D/nn Destination network prefixdst_prefix
Any destination addressdst_any
Command Mode
• /exec/configure/config-postcard-watchlist
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1878
I Commandsip
Page 2023
ip{ [ no ] <seqnum> <permitdeny> { ip { <src_prefix> | <src_any> } { <dst_prefix> | <dst_any> } } } | { no<seqnum> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Sequence numberseqnum
ipip
permitdenypermitdeny
A.B.C.D/nn Source network prefixsrc_prefix
Any source addresssrc_any
A.B.C.D/nn Destination network prefixdst_prefix
Any destination addressdst_any
Command Mode
• /exec/configure/config-int-watchlist
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1879
I Commandsip
Page 2024
ipip [ <ipaddress> | <ipprefix> ] | no ip [ <ipaddress> | <ipprefix> ]
Syntax Description
Negate a command or set its defaultsno
Enable HSRP IPv4 and set the virtual IP addressip
(Optional) Virtual IP addressipaddress
(Optional) Virtual IP address and mask lengthipprefix
Command Mode
• /exec/configure/if-eth-any/hsrp_ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1880
I Commandsip
Page 2025
ipip { <ipv6address> | autoconfig } | no ip [ { <ipv6address> | autoconfig } ]
Syntax Description
Negate a command or set its defaultsno
Enable HSRP IPv6 and set the virtual IP addressip
Obtain address using autoconfigurationautoconfig
Command Mode
• /exec/configure/if-eth-any/hsrp_ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1881
I Commandsip
Page 2026
ip[no] ip <ipaddr>
Syntax Description
(Optional) Negate a command or set its defaultsno
ip address of redundancy group memberip
Redundancy-group node IP addressipaddr
Command Mode
• /exec/configure/if-nve/rgrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1882
I Commandsip
Page 2027
ip[no] ip { { group <gaddr> } | { group-range <gaddr_start> to <gaddr_end> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
IP Addressip
Multicast groupgroup
IPv4 group addressgaddr
Multicast Group address rangegroup-range
First Group addressgaddr_start
Rangeto
Last Group addressgaddr_end
Command Mode
• /exec/configure/nbm-flow-policy/attr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1883
I Commandsip
Page 2028
ip{ { ip <dstip> <srcip> | ipv6 <dstipv6> <srcipv6> } }
Syntax Description
ip addressip
Destination ipv4 addressdstip
source ipv4 addresssrcip
ipv6 addressipv6
Command Mode
• /exec/configure/configngoamccpayload
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1884
I Commandsip
Page 2029
ip access-class[no] ip access-class <name> <inout>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Specify IPv4 access control for packetsaccess-class
List namename
Traffic directioninout
Command Mode
• /exec/configure/line
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1885
I Commandsip access-class
Page 2030
ip access-group[no] ip access-group <name> <inout>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Specify access control for packetsaccess-group
List namename
Traffic directioninout
Command Mode
• /exec/configure/if-set-acl-l3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1886
I Commandsip access-group
Page 2031
ip access-list[no] ip access-list <name> [ client <clienttype> <clientID> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure access listaccess-list
List namename
(Optional) set client typeclient
(Optional) CLI/ONEPclienttype
(Optional) client appIDclientID
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1887
I Commandsip access-list
Page 2032
ip access-list match-local-traffic[no] ip access-list match-local-traffic | ip access-list match-local-traffic
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure access listaccess-list
Enable access-list matching for locally generated trafficmatch-local-traffic
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1888
I Commandsip access-list match-local-traffic
Page 2033
ip address[no] ip address [ { <ip-addr> <ip-mask> | <ip-prefix> } [ route-preference <pref> ] [ tag <tag> ] ] | ip address{ <ip-addr> <ip-mask> | <ip-prefix> } [ route-preference <pref> ] [ tag <tag> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure IP address on interfaceaddress
(Optional) IP address in format i.i.i.iip-addr
(Optional) IP network mask in format m.m.m.mip-mask
(Optional) IP prefix and network mask length in format x.x.x.x/mip-prefix
(Optional) URIB route preference for local/direct routesroute-preference
(Optional) Local/direct route preferencepref
(Optional) URIB route tag value for local/direct routestag
(Optional) Local/direct tag valuetag
Command Mode
• /exec/configure/if-igp /exec/configure/if-mgmt-config /exec/configure/if-mpls-tunnel/exec/configure/if-gre-tunnel /exec/configure/if-vsan /exec/configure/if-cpp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1889
I Commandsip address
Page 2034
ip address dhcp[no] ip address dhcp
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IP address on interfaceaddress
Configure IP address from a dhcp serverdhcp
Command Mode
• /exec/configure/if-vlan /exec/configure/if-ethernet /exec/configure/if-mgmt-config/exec/configure/if-ethernet-all /exec/configure/if-sub
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1890
I Commandsip address dhcp
Page 2035
ip address ipv6 address port[no] { ip address <ip4> | ipv6 address <ip6> } port <portnum> [ protocol <proto> encoding <encoder> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Set destination IPv4 addressip
Set destination IPv6 addressipv6
IP addressaddress
Set destination portport
(Optional) Set transport protocolprotocol
(Optional) Set encoding formatencoding
Destination IPv4 Addressip4
Destination portportnum
(Optional)proto
(Optional)encoder
Command Mode
• /exec/configure/telemetry/destination-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1891
I Commandsip address ipv6 address port
Page 2036
ip address secondary[no] ip address { <ip-addr> <ip-mask> | <ip-prefix> } secondary [ route-preference <pref> ] [ tag <tag> ] | ipaddress { <ip-addr> <ip-mask> | <ip-prefix> } secondary [ route-preference <pref> ] [ tag <tag> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure IP address on interfaceaddress
IP address in format i.i.i.iip-addr
IP network mask in format m.m.m.mip-mask
IP prefix and network mask length in format x.x.x.x/mip-prefix
Configure additional IP addresses on interfacesecondary
(Optional) URIB route preference for local/direct routesroute-preference
(Optional) Local/direct route preferencepref
(Optional) URIB route tag value for local/direct routestag
(Optional) Local/direct tag valuetag
Command Mode
• /exec/configure/if-igp /exec/configure/if-mpls-tunnel /exec/configure/if-mgmt-config/exec/configure/if-gre-tunnel /exec/configure/if-6to4-tunnel /exec/configure/if-vsan /exec/configure/if-cpp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1892
I Commandsip address secondary
Page 2037
ip adjacency peer-gmac[no] ip adjacency [ vrf { <vrf-name> | <vrf-known-name> } ] { <interface> { * | <ip-addr> } | * } peer-gmac
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure Adjmgradjacency
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Display specific interface adjacencies onlyinterface
IPV4 source addressip-addr
for all adjacencies in this context*
Set/clear the peer-gmac bitpeer-gmac
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1893
I Commandsip adjacency peer-gmac
Page 2038
ip adjacency remote-adj[no] ip adjacency [ vrf { <vrf-name> | <vrf-known-name> } ] { <interface> { * | <ip-addr> } | * } remote-adj
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure Adjmgradjacency
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Display specific interface adjacencies onlyinterface
IPV4 source addressip-addr
for all adjacencies in this context*
Set/clear the remote-adj bitremote-adj
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1894
I Commandsip adjacency remote-adj
Page 2039
ip adjacency route distance{ ip adjacency route distance <pref> } | { no ip adjacency route distance }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure Adjmgradjacency
routeroute
admin-distancedistance
preferencepref
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1895
I Commandsip adjacency route distance
Page 2040
ip amt anycast-relay-prefix{ { ip amt anycast-relay-prefix <prefix> } | { no ip amt anycast-relay-prefix [ <prefix> ] } | { ipv6 amtanycast-relay-prefix <prefix6> } | { no ipv6 amt anycast-relay-prefix [ <prefix6> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
AMT global configuration commandsamt
Configure anycast prefix for AMT relayanycast-relay-prefix
IP anycast prefix for AMT relayprefix
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1896
I Commandsip amt anycast-relay-prefix
Page 2041
ip amt gateway[no] ip amt gateway
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
AMT global configuration commandsamt
Configures IPv4 AMT gateway functionalitygateway
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1897
I Commandsip amt gateway
Page 2042
ip amt join-policy{ [ no ] { ip | ipv6 } amt join-policy <jroute-map> [ gateway <groute-map> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
AMT global configuration commandsamt
Configures what (S,G) are allowed to be joinedjoin-policy
Route-map describing (S,G) entries allowedjroute-map
(Optional) Configure join-policy per gatewaygateway
(Optional) Route-map describing gateway or sets of gatewaysgroute-map
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1898
I Commandsip amt join-policy
Page 2043
ip amt qqic[no] { ip | ipv6 } amt qqic <qqic-value>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
AMT global configuration commandsamt
Configure Querier's Query Interval Codeqqic
QQIC valueqqic-value
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1899
I Commandsip amt qqic
Page 2044
ip amt relay-advertisement-address{ { ip amt relay-advertisement-address <address> } | { no ip amt relay-advertisement-address [ <address> ]} | { ipv6 amt relay-advertisement-address <address6> } | { no ipv6 amt relay-advertisement-address [<address6> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
AMT global configuration commandsamt
Address to use by AMT relayrelay-advertisement-address
IP unicast address for AMT relay to useaddress
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1900
I Commandsip amt relay-advertisement-address
Page 2045
ip amt relay[no] ip amt relay
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
AMT global configuration commandsamt
Configures IPv4 AMT relay functionalityrelay
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1901
I Commandsip amt relay
Page 2046
ip amt state-limit{ [ no ] { ip | ipv6 } amt state-limit <limit> [ gateway <route-map> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
AMT global configuration commandsamt
Configure the maximum number of (S,G) entries allowedstate-limit
Number of entries total or per AMT gatewaylimit
(Optional) Configure state limit per gatewaygateway
(Optional) Route-map describing gateway or sets of gatewaysroute-map
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1902
I Commandsip amt state-limit
Page 2047
ip amt tunnel-limit{ { { ip | ipv6 } amt tunnel-limit <limit> } | { no { ip | ipv6 } amt tunnel-limit [ <limit> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
AMT global configuration commandsamt
Configure the maximum tunnels allowedtunnel-limit
Number of tunnelslimit
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1903
I Commandsip amt tunnel-limit
Page 2048
ip arp{ ip arp <ip-address> <mac-address> | no ip arp <ip-address> [ <mac-address> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
IP addressip-address
MAC addressmac-address
Command Mode
• /exec/configure/if-igp /exec/configure/if-mgmt-config /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1904
I Commandsip arp
Page 2049
ip arp allow-static-arp-outside-subnet[no] ip arp allow-static-arp-outside-subnet
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
Allow static ARP outside interface subnetallow-static-arp-outside-subnet
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1905
I Commandsip arp allow-static-arp-outside-subnet
Page 2050
ip arp cache limit{ { ip arp cache limit <max> } | { no ip arp cache limit } } [ syslog <rate> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
ARP cache parameterscache
Limit size of ARP adjacencies cachelimit
Maximum number of ARP entriesmax
(Optional) Syslog messagessyslog
(Optional) Syslogs per secondrate
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1906
I Commandsip arp cache limit
Page 2051
ip arp cos{ ip arp cos <cosval> } | { no ip arp cos }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
COS for ARP packetcos
COS valuecosval
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1907
I Commandsip arp cos
Page 2052
ip arp delete{ ip arp { delete-adj-on-mac-delete | refresh-adj-on-mac-delete <time-out> } | no ip arp {delete-adj-on-mac-delete | refresh-adj-on-mac-delete } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
Delete the adjacency on MAC deletedelete-adj-on-mac-delete
Set refresh timer for mac delete triggerrefresh-adj-on-mac-delete
Refresh value in millisecondstime-out
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1908
I Commandsip arp delete
Page 2053
ip arp event-history size[no] ip arp event-history { packet | event | sync-event | ip-sync-event | control | ha | errors | lcache | lcache-errors| client-event | client-errors | snmp | cli | suppression-event | suppression-errors | controller-errors | sm-trace |dme-event } size { <size_in_text> }
Syntax Description
(Optional) Negate a command or set its defaultsno
IP eventsip
Configure ARP parametersarp
log debug events into event history bufferevent-history
inst packet logspacket
Internal event logsevent
CFS and MCECM related event logssync-event
L3 over vpc eventsip-sync-event
ARP control event logscontrol
HA and GR logsha
inst error logserrors
lcache logslcache
lcache_error logslcache-errors
Client_event logsclient-event
Client_error logsclient-errors
cli logscli
SNMP logssnmp
ARP suppression event logssuppression-event
ARP suppression error logssuppression-errors
Controller MAC-IP route error logscontroller-errors
ARP State machine trace logssm-trace
ARP DME event logsdme-event
Configure the size of the event-hist buffersize
Buffer sizesize_in_text
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1909
I Commandsip arp event-history size
Page 2054
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1910
I Commandsip arp event-history size
Page 2055
ip arp event-history size[no] ip arp event-history { packet | event | sync-event | ip-sync-event | control | ha | errors | lcache | lcache-errors| client-event | client-errors | snmp | cli | suppression-event | suppression-errors | controller-errors | sm-trace |dme-event } size { <size_in_Kbytes> }
Syntax Description
(Optional) Negate a command or set its defaultsno
IP eventsip
Configure ARP parametersarp
log debug events into event history bufferevent-history
inst packet logspacket
Internal event logsevent
CFS and MCECM related event logssync-event
L3 over vpc eventsip-sync-event
ARP control event logscontrol
HA and GR logsha
inst error logserrors
lcache logslcache
lcache_error logslcache-errors
Client_event logsclient-event
Client_error logsclient-errors
cli logscli
SNMP logssnmp
ARP suppression event logssuppression-event
ARP suppression error logssuppression-errors
Controller MAC-IP route error logscontroller-errors
ARP DME event logsdme-event
ARP State machine trace logssm-trace
Configure the size of the event-hist buffersize
Size of the file in kbytessize_in_Kbytes
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1911
I Commandsip arp event-history size
Page 2056
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1912
I Commandsip arp event-history size
Page 2057
ip arp evpn timeout{ ip arp evpn timeout <time-out> } | { no ip arp evpn timeout }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
In EVPN topologyevpn
ARP timeouttimeout
Refresh in EVPN on host moves. supported range is (2000-30000) mstime-out
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1913
I Commandsip arp evpn timeout
Page 2058
ip arp gratuitous hsrp duplicate{ ip arp gratuitous hsrp duplicate | no ip arp gratuitous hsrp duplicate }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
gratuitousgratuitous
hsrphsrp
duplicate address detectionduplicate
Command Mode
• /exec/configure/if-igp /exec/configure/if-mgmt-config /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1914
I Commandsip arp gratuitous hsrp duplicate
Page 2059
ip arp gratuitous request{ ip arp gratuitous request | no ip arp gratuitous request }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
gratuitousgratuitous
Enable/Disable sending grat. arp request when duplicate address detectedrequest
Command Mode
• /exec/configure/if-igp /exec/configure/if-mgmt-config /exec/configure/if-vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1915
I Commandsip arp gratuitous request
Page 2060
ip arp gratuitous update{ ip arp gratuitous update | no ip arp gratuitous update }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
gratuitousgratuitous
Enable/Disable arp cache updates for gratuitous arpupdate
Command Mode
• /exec/configure/if-igp /exec/configure/if-mgmt-config /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1916
I Commandsip arp gratuitous update
Page 2061
ip arp inspection filter vlan[no] ip arp inspection filter <arp-acl-name> vlan <vlan-range>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
Arp Inspection configurationinspection
Filterfilter
Access list namearp-acl-name
Vlan rangevlan
VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19vlan-range
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1917
I Commandsip arp inspection filter vlan
Page 2062
ip arp inspection log-buffer entries[no] ip arp inspection log-buffer { entries <number1> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
Arp Inspection configurationinspection
Log Buffer Configurationlog-buffer
Number of entries for log bufferentries
Number of entries for log buffernumber1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1918
I Commandsip arp inspection log-buffer entries
Page 2063
ip arp inspection trust[no] ip arp inspection trust
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
Arp Inspection configurationinspection
Configure trust statetrust
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1919
I Commandsip arp inspection trust
Page 2064
ip arp inspection validate[no] ip arp inspection validate { src-mac | dst-mac | ip1 } +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
Arp Inspection configurationinspection
Validate addressesvalidate
Validate source MAC addresssrc-mac
Validate destination MAC addressdst-mac
Validate IP addressesip1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1920
I Commandsip arp inspection validate
Page 2065
ip arp inspection vlan[no] ip arp inspection vlan <vlan-id> [ logging { dhcp-bindings { permit | all | inone } } ]
Syntax Description
(Optional) dhcp-bindingslogging
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
Arp Inspection configurationinspection
Enable/Disable ARP Inspection on vlansvlan
VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19vlan-id
(Optional) Logging of packet that match DHCP bindingsdhcp-bindings
(Optional) Log DHCP Binding Permitted packetspermit
(Optional) Log all packets that match DHCP bindingsall
(Optional) Do not log packetsinone
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1921
I Commandsip arp inspection vlan
Page 2066
ip arp off-list timeout{ ip arp off-list timeout <time> } | { no ip arp off-list timeout }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
off-listoff-list
Expire timetimeout
Expire time value in secondstime
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1922
I Commandsip arp off-list timeout
Page 2067
ip arp rarp fabric-forwarding[no] ip arp rarp fabric-forwarding
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
Enable/Disable forwarding of RARP messages on fabricrarp
Forward RARP requests to the fabricfabric-forwarding
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1923
I Commandsip arp rarp fabric-forwarding
Page 2068
ip arp rarp fabric-forwarding[no] ip arp rarp fabric-forwarding
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
Enable/Disable forwarding of RARP messages on fabricrarp
Forward RARP requests to the fabricfabric-forwarding
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1924
I Commandsip arp rarp fabric-forwarding
Page 2069
ip arp rarp fabric-forwarding rate-limit[no] ip arp rarp fabric-forwarding rate-limit <rate>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
Enable/Disable forwarding of RARP messages on fabricrarp
Forward RARP requests to the fabricfabric-forwarding
Forwarding rate of the RARP framesrate-limit
RARP frames-per-secondrate
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1925
I Commandsip arp rarp fabric-forwarding rate-limit
Page 2070
ip arp suppression-cacheip arp suppression-cache { [ clear { local | remote } vlan <vlan-id> [ <ip-address> ] ] | [ download remotevlan <vlan-id> [ <ip-address> ] ] }
Syntax Description
(Optional) Clear ARP suppression cache entriesclear
Clear IP commandsip
(Optional) download local entires from ARP cache, remote from l2ribdownload
Clear ARP table and statisticsarp
ARP-suppression cachesuppression-cache
(Optional) Local entrieslocal
(Optional) Remote entriesremote
(Optional) Vlan idvlan
(Optional) Vlanvlan-id
(Optional) IP addressip-address
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1926
I Commandsip arp suppression-cache
Page 2071
ip arp suppression timeout{ ip arp suppression timeout <time-out> } | { no ip arp suppression timeout }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
ARP-suppression based eventsuppression
ARP timeouttimeout
Time-out value in seconds. Time-out = 0 indicates disabledtime-out
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1927
I Commandsip arp suppression timeout
Page 2072
ip arp synchronize[no] ip arp synchronize
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
ARParp
CFS synchronizesynchronize
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1928
I Commandsip arp synchronize
Page 2073
ip arp timeout{ ip arp timeout <time-out> } | { no ip arp timeout }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
ARP timeouttimeout
Time-out value in secondstime-out
Command Mode
• /exec/configure/config-mgmt /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1929
I Commandsip arp timeout
Page 2074
ip arp timeout{ ip arp timeout <time-out> } | { no ip arp timeout }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
ARP timeouttimeout
Time-out value in secondstime-out
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1930
I Commandsip arp timeout
Page 2075
ip arp unnum-svi-dup-ip-detection[no] ip arp unnum-svi-dup-ip-detection
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
Enable duplicate IP detection across VLANs for IP unnumbered SVIs.unnum-svi-dup-ip-detection
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1931
I Commandsip arp unnum-svi-dup-ip-detection
Page 2076
ip arp unnum-svi-sw-replication[no] ip arp unnum-svi-sw-replication
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure ARP parametersarp
ARP packets replication in software for unnumbered SVIunnum-svi-sw-replication
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1932
I Commandsip arp unnum-svi-sw-replication
Page 2077
ip as-path access-list deny{ ip as-path access-list <aspl-name> [ timeout <sec> ] { { deny | permit } <line> } } | { no ip as-path access-list<aspl-name> [ timeout <sec> ] [ { deny | permit } <line> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
BGP autonomous system path filteras-path
Specify an access list nameaccess-list
AS path access list nameaspl-name
Known as-path access-list nameaspl-name
(Optional) Timeout to be used for checking regex cpu hogtimeout
(Optional) No. of seconds used as timeoutsec
Specify packets to rejectdeny
Specify packets to forwardpermit
Aline
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1933
I Commandsip as-path access-list deny
Page 2078
ip as-path access-list deny{ ip as-path access-list <aspl-name> [ timeout <sec> ] { { deny | permit } <line> } } | { no ip as-path access-list<aspl-name> [ timeout <sec> ] [ { deny | permit } <line> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
BGP autonomous system path filteras-path
Specify an access list nameaccess-list
AS path access list nameaspl-name
Known as-path access-list nameaspl-name
(Optional) Timeout to be used for checking regex cpu hogtimeout
(Optional) No. of seconds used as timeoutsec
Specify packets to rejectdeny
Specify packets to forwardpermit
Aline
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1934
I Commandsip as-path access-list deny
Page 2079
ip as-path access-list seq deny{ ip as-path access-list <aspl-name> seq <seq> [ timeout <sec> ] { { deny | permit } <line> } } | { no ip as-pathaccess-list <aspl-name> seq <seq> [ timeout <sec> ] [ { deny | permit } <line> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
BGP autonomous system path filteras-path
Specify an access list nameaccess-list
AS path access list nameaspl-name
Known as-path access-list nameaspl-name
Sequence number of an entryseq
Sequence numberseq
(Optional) Timeout to be used for checking regex cpu hogtimeout
(Optional) No. of seconds used as timeoutsec
Specify packets to rejectdeny
Specify packets to forwardpermit
Aline
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1935
I Commandsip as-path access-list seq deny
Page 2080
ip authentication[no] { ip | ipv6 } authentication { { key-chain eigrp <eigrp-ptag> <chain> } | { mode eigrp <eigrp-ptag> md5} }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Configures EIGRP authentication subcommandsauthentication
key-chainkey-chain
Process tageigrp-ptag
name of key-chainchain
modemode
EIGRP interface configuration commandseigrp
Keyed message digestmd5
eigrp-ptag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1936
I Commandsip authentication
Page 2081
ip auto-discard[no] ip auto-discard
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Auto 0.0.0.0/0 discard routeauto-discard
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1937
I Commandsip auto-discard
Page 2082
ip bandwidth-percent eigrp{ { { ip | ipv6 } bandwidth-percent eigrp <eigrp-ptag> <percent> } | { no { ip | ipv6 } bandwidth-percent eigrp<eigrp-ptag> [ <percent> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Configures IP-EIGRP bandwidth limitbandwidth-percent
EIGRP interface configuration commandseigrp
Process tageigrp-ptag
Maximum bandwidth percentage that EIGRP may usepercent
eigrp-ptag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1938
I Commandsip bandwidth-percent eigrp
Page 2083
ip bandwidth eigrp{ { { ip | ipv6 } bandwidth eigrp <eigrp-ptag> <bw> } | { no { ip | ipv6 } bandwidth eigrp <eigrp-ptag> [<bw> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Set bandwidth for interface used in EIGRP metric calculationbandwidth
EIGRP interface configuration commandseigrp
Process tageigrp-ptag
Bandwidth in kilobitsbw
eigrp-ptag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1939
I Commandsip bandwidth eigrp
Page 2084
ip community-list expanded deny{ ip community-list expanded <name> [ timeout <sec> ] { deny | permit } <line> } | { no ip community-listexpanded <name> [ timeout <sec> ] [ { deny | permit } <line> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Add a community list entrycommunity-list
Add an expanded community list entryexpanded
Name of expanded community listname
(Optional) Timeout to be used for checking regex cpu hogtimeout
(Optional) No. of seconds used as timeoutsec
Specify community to rejectdeny
Specify community to acceptpermit
Regular-expression(mustline
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1940
I Commandsip community-list expanded deny
Page 2085
ip community-list expanded deny{ ip community-list expanded <name> [ timeout <sec> ] { deny | permit } <line> } | { no ip community-listexpanded <name> [ timeout <sec> ] [ { deny | permit } <line> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Add a community list entrycommunity-list
Add an expanded community list entryexpanded
Name of expanded community listname
(Optional) Timeout to be used for checking regex cpu hogtimeout
(Optional) No. of seconds used as timeoutsec
Specify community to rejectdeny
Specify community to acceptpermit
Regular-expression(mustline
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1941
I Commandsip community-list expanded deny
Page 2086
ip community-list expanded seq deny{ ip community-list expanded <name> seq <seq> [ timeout <sec> ] { deny | permit } <line> } | { no ipcommunity-list expanded <name> seq <seq> [ timeout <sec> ] [ { deny | permit } <line> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Add a community list entrycommunity-list
Add an expanded community list entryexpanded
Name of expanded community listname
Sequence number of an entryseq
Sequence numberseq
(Optional) Timeout to be used for checking regex cpu hogtimeout
(Optional) No. of seconds used as timeoutsec
Specify community to rejectdeny
Specify community to acceptpermit
Regular-expression(mustline
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1942
I Commandsip community-list expanded seq deny
Page 2087
ip community-list standard permit internet local-AS{ ip community-list standard <name> { permit | deny } { internet | local-AS | no-advertise | no-export | <aann>| <number> | <hex_num> } + } | { no ip community-list standard <name> [ permit | deny ] [ { internet | local-AS| no-advertise | no-export | <aann> | <number> | <hex_num> } + ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Add a community list entrycommunity-list
Add a standard Community list entrystandard
Standard community list namename
Specify community to acceptpermit
Specify community to rejectdeny
Internet (well-known community)internet
Do not send outside local AS (well-known community)local-AS
Do not advertise to any peer (well-known community)no-advertise
Do not export to next AS (well-known community)no-export
Community number aa:nn formataann
Community numbernumber
Community number in hexhex_num
(Optional) local-ASinternet
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1943
I Commandsip community-list standard permit internet local-AS
Page 2088
ip community-list standard permit internet local-AS{ ip community-list standard <name> { permit | deny } { internet | local-AS | no-advertise | no-export | <aann>| <number> | <hex_num> } + } | { no ip community-list standard <name> [ permit | deny ] [ { internet | local-AS| no-advertise | no-export | <aann> | <number> | <hex_num> } + ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Add a community list entrycommunity-list
Add a standard Community list entrystandard
Standard community list namename
Specify community to acceptpermit
Specify community to rejectdeny
Internet (well-known community)internet
Do not send outside local AS (well-known community)local-AS
Do not advertise to any peer (well-known community)no-advertise
Do not export to next AS (well-known community)no-export
Community number aa:nn formataann
Community numbernumber
Community number in hexhex_num
(Optional) local-ASinternet
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1944
I Commandsip community-list standard permit internet local-AS
Page 2089
ip community-list standard seq permit internet local-AS{ ip community-list standard <name> seq <seq> { permit | deny } { internet | local-AS | no-advertise | no-export| <aann> | <number> | <hex_num> } + } | { no ip community-list standard <name> seq <seq> [ permit | deny] [ { internet | local-AS | no-advertise | no-export | <aann> | <number> | <hex_num> } + ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Add a community list entrycommunity-list
Add a standard Community list entrystandard
Standard community list namename
Sequence number of an entryseq
Sequence numberseq
Specify community to acceptpermit
Specify community to rejectdeny
Internet (well-known community)internet
Do not send outside local AS (well-known community)local-AS
Do not advertise to any peer (well-known community)no-advertise
Do not export to next AS (well-known community)no-export
Community number aa:nn formataann
Community numbernumber
Community number in hexhex_num
(Optional) local-ASinternet
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1945
I Commandsip community-list standard seq permit internet local-AS
Page 2090
ip delay eigrp{ { { ip | ipv6 } delay eigrp <eigrp-ptag> <delay> [ picoseconds ] } | { no { ip | ipv6 } delay eigrp <eigrp-ptag>[ <delay> ] [ picoseconds ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Set delay for interface used in EIGRP metric calculationdelay
EIGRP interface configuration commandseigrp
Process tageigrp-ptag
Throughput delaydelay
(Optional) Delay units in picosecondspicoseconds
eigrp-ptag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1946
I Commandsip delay eigrp
Page 2091
ip destination{ ip { destination | source } <addr> } | { no ip { destination | source } }
Syntax Description
Negate a command or set its defaultsno
specify flow ipv4 addressip
specify flow source ipv4 addresssource
specify flow destination ip addressdestination
ipv4 addressaddr
Command Mode
• /exec/configure/configngoamprofileflow
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1947
I Commandsip destination
Page 2092
ip dhcp option82 suboption circuit-id[no] ip dhcp option82 suboption circuit-id [ <format-string> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP option82option82
DHCP option82 suboption informationsuboption
DHCP option82 suboption circuit-id string configurationcircuit-id
(Optional) Format stringformat-string
Command Mode
• /exec/configure/if-eth-phy /exec/configure/if-eth-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1948
I Commandsip dhcp option82 suboption circuit-id
Page 2093
ip dhcp packet strict-validation[no] ip dhcp packet strict-validation
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP packetpacket
DHCP packet strict validationstrict-validation
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1949
I Commandsip dhcp packet strict-validation
Page 2094
ip dhcp relay[no] ip dhcp relay
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
Enable DHCP relay agentrelay
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1950
I Commandsip dhcp relay
Page 2095
ip dhcp relay address[no] ip dhcp relay address [ <ip-addr-val> [ use-vrf <vrf-name> ] ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
Configure relay agentrelay
Configure DHCP server to refer toaddress
(Optional) IP addressip-addr-val
(Optional) helper address VRF membershipuse-vrf
(Optional) VRF namevrf-name
Command Mode
• /exec/configure/if-igp /exec/configure/ppm-ethernet-switch /exec/configure/ppm-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1951
I Commandsip dhcp relay address
Page 2096
ip dhcp relay information option[no] ip dhcp relay information option
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP relay agent parametersrelay
Relay agent information optioninformation
Insert relay information in BOOTREQUESToption
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1952
I Commandsip dhcp relay information option
Page 2097
ip dhcp relay information option trust[no] ip dhcp relay information option trust
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP relay agent parametersrelay
Relay agent information optioninformation
Relay agent optionoption
Enable relay trust functionality on the systemtrust
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1953
I Commandsip dhcp relay information option trust
Page 2098
ip dhcp relay information option vpn[no] ip dhcp relay information option vpn
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP relay agent parametersrelay
Relay agent information optioninformation
Insert relay information in BOOTREQUESToption
Enable relay support across VRFsvpn
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1954
I Commandsip dhcp relay information option vpn
Page 2099
ip dhcp relay information trust-all[no] ip dhcp relay information trust-all
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP relay agent parametersrelay
Relay agent information optioninformation
Enable relay trust on all the interfacestrust-all
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1955
I Commandsip dhcp relay information trust-all
Page 2100
ip dhcp relay information trusted[no] ip dhcp relay information trusted
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP relay agent parametersrelay
Relay agent information optioninformation
Enable relay trust on this interfacetrusted
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1956
I Commandsip dhcp relay information trusted
Page 2101
ip dhcp relay source-interface[no] ip dhcp relay source-interface
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
Configure relay agentrelay
Configure source interface for DHCP relaysource-interface
Command Mode
• /exec/configure /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1957
I Commandsip dhcp relay source-interface
Page 2102
ip dhcp relay source-interfaceip dhcp relay source-interface <interface-name>
Syntax Description
Configure IP featuresip
Configure DHCP snooping or relaydhcp
Configure relay agentrelay
Configure source interface for DHCP relaysource-interface
Source interfaceinterface-name
Command Mode
• /exec/configure /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1958
I Commandsip dhcp relay source-interface
Page 2103
ip dhcp relay sub-option circuit-id customized[no] ip dhcp relay sub-option circuit-id customized
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP relay agent parametersrelay
Relay agent information option sub-optionsub-option
sub-option of option82circuit-id
circuit id customized to include vlan id, slot and port infocustomized
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1959
I Commandsip dhcp relay sub-option circuit-id customized
Page 2104
ip dhcp relay sub-option circuit-id format-type string[no] ip dhcp relay sub-option circuit-id format-type string [ format <format-string> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP relay agent parametersrelay
Relay agent suboptionsub-option
Relay agent circuit-id suboptioncircuit-id
Specify suboption format typeformat-type
Use string format for suboptionstring
(Optional) Specify format stringformat
(Optional) Format stringformat-string
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1960
I Commandsip dhcp relay sub-option circuit-id format-type string
Page 2105
ip dhcp relay sub-option type cisco[no] ip dhcp relay sub-option type cisco
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP relay agent parametersrelay
Relay agent suboptionsub-option
Relay agent suboption typetype
Use Cisco propritery suboptionscisco
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1961
I Commandsip dhcp relay sub-option type cisco
Page 2106
ip dhcp smart-relay[no] ip dhcp smart-relay
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
Configure DHCP smart relay on interfacesmart-relay
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1962
I Commandsip dhcp smart-relay
Page 2107
ip dhcp smart-relay global[no] ip dhcp smart-relay global
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
Configure DHCP smart relaysmart-relay
Configure DHCP smart relay globallyglobal
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1963
I Commandsip dhcp smart-relay global
Page 2108
ip dhcp snooping[no] ip dhcp snooping
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP Snoopingsnooping
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1964
I Commandsip dhcp snooping
Page 2109
ip dhcp snooping information option[no] ip dhcp snooping information option
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP Snoopingsnooping
DHCP Snooping informationinformation
DHCP Snooping information optionoption
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1965
I Commandsip dhcp snooping information option
Page 2110
ip dhcp snooping ipsg-excluded vlan[no] ip dhcp snooping ipsg-excluded vlan <vlan-id10>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP Snoopingsnooping
exclude ipsgipsg-excluded
DHCP Snooping ipsg excluded vlanvlan
VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19vlan-id10
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1966
I Commandsip dhcp snooping ipsg-excluded vlan
Page 2111
ip dhcp snooping sub-option circuit-id format-type string[no] ip dhcp snooping sub-option circuit-id format-type string [ format <format-string> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP snooping parameterssnooping
suboptionsub-option
circuit-id suboptioncircuit-id
Specify suboption format typeformat-type
Use string format for suboptionstring
(Optional) Specify format stringformat
(Optional) Format stringformat-string
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1967
I Commandsip dhcp snooping sub-option circuit-id format-type string
Page 2112
ip dhcp snooping trust[no] ip dhcp snooping trust
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP Snoopingsnooping
DHCP Snooping trust configtrust
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1968
I Commandsip dhcp snooping trust
Page 2113
ip dhcp snooping verify mac-address[no] ip dhcp snooping verify mac-address
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP Snoopingsnooping
DHCP snooping verifyverify
DHCP snooping verify mac-addressmac-address
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1969
I Commandsip dhcp snooping verify mac-address
Page 2114
ip dhcp snooping vlan[no] ip dhcp snooping vlan <vlan-id10>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure DHCP snooping or relaydhcp
DHCP Snoopingsnooping
DHCP Snooping vlanvlan
VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19vlan-id10
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1970
I Commandsip dhcp snooping vlan
Page 2115
ip directed-broadcast[no] ip directed-broadcast [ <acl-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IP directed-broadcastdirected-broadcast
(Optional) ACL policy nameacl-name
Command Mode
• /exec/configure/if-igp /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1971
I Commandsip directed-broadcast
Page 2116
ip distribute-list eigrp[no] { ip | ipv6 } distribute-list eigrp <eigrp-ptag> { { route-map <map> } | { prefix-list <list> } } { in | out}
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Filter networks in routing updatesdistribute-list
EIGRP interface configuration commandseigrp
Process tageigrp-ptag
Use a route-map for route filteringroute-map
Route-map namemap
Use a prefix-list for route filteringprefix-list
Reference to prefix-list namelist
Filter incoming routing updatesin
Filter outgoing routing updatesout
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1972
I Commandsip distribute-list eigrp
Page 2117
ip dns source-interface[no] ip dns source-interface <ifnum> [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure dns clientdns
Configure source interface feature for domain-lookupsource-interface
Source interfaceifnum
(Optional) Configure VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1973
I Commandsip dns source-interface
Page 2118
ip domain-list[no] ip domain-list { <s0> | <s1> [ use-vrf { <vrf-name> | <vrf-known-name> } ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Add additional domain namesdomain-list
Enter a domains0
Enter a domains1
(Optional) Display per-VRF informationuse-vrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1974
I Commandsip domain-list
Page 2119
ip domain-lookup[no] ip domain-lookup
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Enable/Disable DNSdomain-lookup
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1975
I Commandsip domain-lookup
Page 2120
ip domain-name[no] ip domain-name { <s0> | <s1> [ use-vrf { <vrf-name> | <vrf-known-name> } ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Specify default domain namedomain-name
Enter the default domains0
Enter the default domains1
(Optional) Display per-VRF informationuse-vrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1976
I Commandsip domain-name
Page 2121
ip drop-glean[no] ip drop-glean
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Installs the secondary subnet routes as Drop routesdrop-glean
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1977
I Commandsip drop-glean
Page 2122
ip dscp-lop[no] ip dscp-lop | ip dscp-lop { <dscp-val> | <dscp-enum> }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Set DSCP to be used for locally originated packets for IPv4 and IPv6.Cos will not be set.
dscp-lop
Specify DSCP value for Locally Originated packets for IPv4 and IPv6dscp-val
dscp-enum
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1978
I Commandsip dscp-lop
Page 2123
ip dscp[no] ip dscp <dscp_value>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set ERSPAN IP optionsip
Set the IP DSCP valuedscp
dscp_value
Command Mode
• /exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1979
I Commandsip dscp
Page 2124
ip eigrp bfd[no] ip eigrp <eigrp-tag> bfd [ disable ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
EIGRP interface configuration commandseigrp
Process tageigrp-tag
Enable BFD on this interfacebfd
(Optional) Disable BFD on this interfacedisable
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1980
I Commandsip eigrp bfd
Page 2125
ip eigrp event-history bfd size[no] { ip | ipv6 } eigrp [ <eigrp-ptag> ] event-history bfd size { <size_in_text> | <size_in_Kbytes> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Clear IP commandsip
Clear IPv6 commandsipv6
EIGRP clear commandseigrp
(Optional) Process tageigrp-ptag
Event History of EIGRPevent-history
Show bfd log of EIGRPbfd
Configure the size of the event-hist buffersize
Buffer sizesize_in_text
Size of the file in kbytessize_in_Kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1981
I Commandsip eigrp event-history bfd size
Page 2126
ip eigrp event-history errors[no] { ip | ipv6 } eigrp [ <eigrp-ptag> ] event-history { errors | msgs }
Syntax Description
(Optional) Negate a command or set its defaultsno
Clear IP commandsip
Clear IPv6 commandsipv6
EIGRP clear commandseigrp
(Optional) Process tageigrp-ptag
Event History of EIGRPevent-history
Show error log of EIGRPerrors
Show message log of EIGRPmsgs
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1982
I Commandsip eigrp event-history errors
Page 2127
ip eigrp event-history size[no] { ip | ipv6 } eigrp [ <eigrp-ptag> ] event-history { fsm | packet | rib } size { <size_in_text> |<size_in_Kbytes> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Clear IP commandsip
Clear IPv6 commandsipv6
EIGRP clear commandseigrp
(Optional) Process tageigrp-ptag
Event History of EIGRPevent-history
FSM log of EIGRPfsm
Packet log of EIGRPpacket
RIB log of EIGRPrib
Configure the size of the event-hist buffersize
Buffer sizesize_in_text
Size of the file in kbytessize_in_Kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1983
I Commandsip eigrp event-history size
Page 2128
ip eigrp shutdown[no] { ip | ipv6 } eigrp <eigrp-ptag> shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
EIGRP interface configuration commandseigrp
Process tageigrp-ptag
Shutdown EIGRP on this interfaceshutdown
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1984
I Commandsip eigrp shutdown
Page 2129
ip extcommunity-list expanded deny{ ip extcommunity-list expanded <name> { deny | permit } <line> } | { no ip extcommunity-list expanded<name> [ { deny | permit } <line> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Add a extcommunity list entryextcommunity-list
Add an expanded extcommunity list entryexpanded
Name of expanded extcommunity listname
Specify extcommunity to rejectdeny
Specify extcommunity to acceptpermit
Regular-expression(mustline
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1985
I Commandsip extcommunity-list expanded deny
Page 2130
ip extcommunity-list standard permit{ ip extcommunity-list standard <name> { permit | deny } { { 4byteas-generic { transitive<ext-comm-gen-trans> | non-transitive <ext-comm-gen-nontrans> } } | { rt { <ext-comm-rt-aa2nn4> |<ext-comm-rt-aa4nn2> } } | { soo { <ext-comm-soo-aa2nn4> | <ext-comm-soo-aa4nn2> } } } + | { no ipextcommunity-list standard <name> [ permit | deny ] [ { 4byteas-generic { transitive <ext-comm-gen-trans>| non-transitive <ext-comm-gen-nontrans> } } | { rt { <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } } |{ soo { <ext-comm-soo-aa2nn4> | <ext-comm-soo-aa4nn2> } } ] + } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Add a extcommunity list entryextcommunity-list
Add a standard Extcommunity list entrystandard
Standard extcommunity list namename
Specify extcommunity to acceptpermit
Specify extcommunity to rejectdeny
Generic extended community4byteas-generic
Transitive extcommunitytransitive
Non-Transitive extcommunitynon-transitive
Router-Targetrt
Site-Of-Originsoo
Extcommunity number aa4:nn formatext-comm-gen-trans
Extcommunity number aa4:nn formatext-comm-gen-nontrans
Extcommunity numberext-comm-rt-aa2nn4
Extcommunity numberext-comm-rt-aa4nn2
Extcommunity numberext-comm-soo-aa2nn4
Extcommunity numberext-comm-soo-aa4nn2
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1986
I Commandsip extcommunity-list standard permit
Page 2131
ip fabric multicast file-debug[no] ip fabric multicast file-debug
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Config fabricfabric
Configure multicastmulticast
Collect all debugs to a filefile-debug
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1987
I Commandsip fabric multicast file-debug
Page 2132
ip flow monitor input[no] ip flow monitor <monitorname> input
Syntax Description
Configure IP featuresip
NetFlow related commandsflow
Apply a Flow Monitor to this interfacemonitor
Name of Flow Monitormonitorname
Apply Flow Monitor on input trafficinput
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1988
I Commandsip flow monitor input
Page 2133
ip flow monitor input[no] ip flow monitor <monitorname> input
Syntax Description
Configure IP featuresip
NetFlow related commandsflow
Apply a Flow Monitor to this interfacemonitor
Name of Flow Monitormonitorname
Apply Flow Monitor on input trafficinput
Command Mode
• /exec/configure/if-routing /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1989
I Commandsip flow monitor input
Page 2134
ip flow monitor input[no] ip flow monitor <monitorname> input
Syntax Description
Configure IP featuresip
NetFlow related commandsflow
Apply a Flow Monitor to this interfacemonitor
Name of Flow Monitormonitorname
Apply Flow Monitor on input trafficinput
Command Mode
• /exec/configure/vlan-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1990
I Commandsip flow monitor input
Page 2135
ip forwardip forward | no ip forward
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Enable ip forwarding on interfaceforward
Command Mode
• /exec/configure/if-vlan /exec/configure/if-vlan-range /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1991
I Commandsip forward
Page 2136
ip ftp source-interface[no] ip ftp source-interface <ifnum> [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure FTP clientftp
Configure source interface feature for FTP clientsource-interface
Source interfaceifnum
(Optional) Configure VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1992
I Commandsip ftp source-interface
Page 2137
ip hello-interval eigrp{ { { ip | ipv6 } hello-interval eigrp <eigrp-ptag> <hello-interval> } | { no { ip | ipv6 } hello-interval eigrp<eigrp-ptag> [ <hello-interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Configures IP-EIGRP hello intervalhello-interval
EIGRP interface configuration commandseigrp
Process tageigrp-ptag
Seconds between hello transmissionshello-interval
eigrp-ptag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1993
I Commandsip hello-interval eigrp
Page 2138
ip hold-time eigrp{ { { ip | ipv6 } hold-time eigrp <eigrp-ptag> <holdtime> } | { no { ip | ipv6 } hold-time eigrp <eigrp-ptag>[ <holdtime> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Configures IP-EIGRP hold timehold-time
EIGRP interface configuration commandseigrp
Process tageigrp-ptag
Seconds before neighbor is considered downholdtime
eigrp-ptag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1994
I Commandsip hold-time eigrp
Page 2139
ip host[no] ip host <s0> [ <ipv4_0> ] | ip host <s0> <ipv4_0>
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Add an entry to the ip hostname tablehost
Name of Hosts0
(Optional) Enter an IP addressipv4_0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1995
I Commandsip host
Page 2140
ip host host{ [ <seqnum> ] <permitdeny> { ip { <src_addr> <src_wild> | <src_prefix> | <src_any> | host <src_hostaddr>} { <dst_addr> <dst_wild> | <dst_prefix> | <dst_any> | host <dst_hostaddr> } } } | { no <seqnum> }
Syntax Description
Negate a command or set its defaultsno
(Optional) Sequence numberseqnum
ipip
permitdenypermitdeny
Source network addresssrc_addr
Source wildcard bitssrc_wild
A.B.C.D/nn Source network prefixsrc_prefix
Any source addresssrc_any
A.B.C.D - A single source hosthost
A.B.C.D - A single source hostsrc_hostaddr
Destination network addressdst_addr
Destination wildcard bitsdst_wild
A.B.C.D/nn Destination network prefixdst_prefix
Any destination addressdst_any
A.B.C.D - A single destination hosthost
A.B.C.D - A single destination hostdst_hostaddr
Command Mode
• /exec/configure/catena-port-acl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1996
I Commandsip host host
Page 2141
ip http source-interface[no] ip http source-interface <ifnum> [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure HTTP clienthttp
Configure source interface feature for HTTP clientsource-interface
Source interfaceifnum
(Optional) Configure VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1997
I Commandsip http source-interface
Page 2142
ip icmp-errors source-interfaceip icmp-errors source-interface <interface> [ <icmp_type> ] | no ip icmp-errors source-interface [ <interface><icmp_type> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
ICMP unreachable/TTL-exceeded/param-prob messagesicmp-errors
Configure source-address for applicationssource-interface
Interface to pick source-address frominterface
(Optional) ICMPv6 typesicmp_type
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1998
I Commandsip icmp-errors source-interface
Page 2143
ip igmp any-query-destination[no] ip igmp any-query-destination
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Allow any destination-IP for General Queriesany-query-destination
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)1999
I Commandsip igmp any-query-destination
Page 2144
ip igmp enforce-router-alert[no] ip igmp enforce-router-alert
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Enforce Router Alert option check for IGMPv2 and IGMPv3 packetsenforce-router-alert
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2000
I Commandsip igmp enforce-router-alert
Page 2145
ip igmp event-history cli[no] ip igmp event-history cli { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configure event-history buffersevent-history
CLI events for IGMPcli
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2001
I Commandsip igmp event-history cli
Page 2146
ip igmp event-history ha[no] ip igmp event-history ha { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configure event-history buffersevent-history
HA events for IGMPha
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2002
I Commandsip igmp event-history ha
Page 2147
ip igmp event-history interface[no] ip igmp event-history { interface-debugs | group-debugs } { size { <size_in_text> | <size_in_kbytes> }}
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configure event-history buffersevent-history
Interface-debugs for IGMPinterface-debugs
Group-debugs for IGMPgroup-debugs
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2003
I Commandsip igmp event-history interface
Page 2148
ip igmp event-history interface[no] ip igmp event-history { interface-events | group-events } { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configure event-history buffersevent-history
Interface-events for IGMPinterface-events
Group-events for IGMPgroup-events
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2004
I Commandsip igmp event-history interface
Page 2149
ip igmp event-history mtrace[no] ip igmp event-history mtrace { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configure event-history buffersevent-history
Mtrace events for IGMPmtrace
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2005
I Commandsip igmp event-history mtrace
Page 2150
ip igmp event-history mvr[no] ip igmp event-history mvr { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configure event-history buffersevent-history
MVR events for IGMPmvr
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2006
I Commandsip igmp event-history mvr
Page 2151
ip igmp event-history nbm[no] ip igmp event-history nbm { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configure event-history buffersevent-history
NBM events for IGMPnbm
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2007
I Commandsip igmp event-history nbm
Page 2152
ip igmp event-history policy[no] ip igmp event-history policy { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configure event-history buffersevent-history
Policy events for IGMPpolicy
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2008
I Commandsip igmp event-history policy
Page 2153
ip igmp event-history vrf[no] ip igmp event-history vrf { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configure event-history buffersevent-history
VRF events for IGMPvrf
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2009
I Commandsip igmp event-history vrf
Page 2154
ip igmp file-debug[no] ip igmp file-debug
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Collect all debugs to a filefile-debug
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2010
I Commandsip igmp file-debug
Page 2155
ip igmp flush-routes[no] ip igmp flush-routes
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Remove routes when restarting IGMPflush-routes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2011
I Commandsip igmp flush-routes
Page 2156
ip igmp group-timeout{ { no ip igmp group-timeout [ <time> ] } | { ip igmp group-timeout <time> } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Configures group membership timeout for IGMPv2group-timeout
(Optional) Time in secondstime
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2012
I Commandsip igmp group-timeout
Page 2157
ip igmp heavy-template[no] ip igmp heavy-template
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
IGMP heavy for IGMP scaleheavy-template
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2013
I Commandsip igmp heavy-template
Page 2158
ip igmp host-proxy[no] ip igmp host-proxy [ unsolicited [ <time> ] | route-map <route-map-name> [ unsolicited [ <time> ] ] |prefix-list <prefix-list-name> [ unsolicited [ <time> ] ] ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Configures igmp host proxy for this interfacehost-proxy
(Optional) host proxy route-map policyroute-map
(Optional) host proxy prefix-list policyprefix-list
(Optional) unsolicited joinsunsolicited
(Optional) Time in seconds.time
(Optional) Route-map nameroute-map-name
(Optional) Name of prefix-listprefix-list-name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2014
I Commandsip igmp host-proxy
Page 2159
ip igmp immediate-leave[no] ip igmp immediate-leave
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Enable/Disable immediate leaveimmediate-leave
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2015
I Commandsip igmp immediate-leave
Page 2160
ip igmp join-group[no] ip igmp join-group { { <group> [ source <source> ] } | { route-map <route-map-name> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Configures local group membership for routerjoin-group
Multicast group IP addressgroup
(Optional) Configures source address for IGMPv3 (S,G) Channelsource
(Optional) Source IP addresssource
Join group policyroute-map
Route-map nameroute-map-name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2016
I Commandsip igmp join-group
Page 2161
ip igmp last-member-query-count{ { no ip igmp last-member-query-count [ <count> ] } | { ip igmp last-member-query-count <count> } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Configures number of group-specific Queries sentlast-member-query-count
(Optional) Count valuecount
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2017
I Commandsip igmp last-member-query-count
Page 2162
ip igmp last-member-query-response-time{ { no ip igmp last-member-query-response-time [ <interval> ] } | { ip igmp last-member-query-response-time<interval> } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Configures last member query response timelast-member-query-response-time
(Optional) Interval in secondsinterval
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2018
I Commandsip igmp last-member-query-response-time
Page 2163
ip igmp querier-elect strict[no] ip igmp querier-elect strict
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Querier electionquerier-elect
Consider subnet check for L3 igmp querier electionstrict
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2019
I Commandsip igmp querier-elect strict
Page 2164
ip igmp querier{ { no ip igmp { querier-timeout | query-timeout } [ <time> ] } | { ip igmp { querier-timeout | query-timeout} <time> } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Configures querier timeout for IGMPv2querier-timeout
Configures querier timeout for IGMPv2query-timeout
(Optional) Time in secondstime
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2020
I Commandsip igmp querier
Page 2165
ip igmp query-interval{ { no ip igmp query-interval [ <interval> ] } | { ip igmp query-interval <interval> } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Configures interval between Query transmissionquery-interval
(Optional) Interval in secondsinterval
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2021
I Commandsip igmp query-interval
Page 2166
ip igmp query-max-response-time{ { no ip igmp query-max-response-time [ <time> ] } | { ip igmp query-max-response-time <time> } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Configures MRT for query messagesquery-max-response-time
(Optional) Time in secondstime
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2022
I Commandsip igmp query-max-response-time
Page 2167
ip igmp report-link-local-groups[no] ip igmp report-link-local-groups
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Send Reports for groups in 224.0.0.0/24report-link-local-groups
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2023
I Commandsip igmp report-link-local-groups
Page 2168
ip igmp report prefix-list{ { ip igmp { report-policy | access-group } { <route-map-name> | prefix-list <prefix-list-name> } } | { no ipigmp { report-policy | access-group } [ <route-map-name> | prefix-list <prefix-list-name> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
IGMP Report Policyreport-policy
IGMP access-groupaccess-group
Route-map nameroute-map-name
Prefix list policyprefix-list
Name of prefix-listprefix-list-name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2024
I Commandsip igmp report prefix-list
Page 2169
ip igmp robustness-variable{ { no ip igmp robustness-variable [ <value> ] } | { ip igmp robustness-variable <value> } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Configures RFC defined Robustness Variablerobustness-variable
(Optional) Count valuevalue
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2025
I Commandsip igmp robustness-variable
Page 2170
ip igmp snooping{ { no ip igmp snooping } | { ip igmp snooping } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP configuration commandsigmp
Configures IGMP Snoopingsnooping
Command Mode
• /exec/configure/vlan-config /exec/configure/bdomain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2026
I Commandsip igmp snooping
Page 2171
ip igmp snooping{ { no ip igmp snooping } | { ip igmp snooping } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2027
I Commandsip igmp snooping
Page 2172
ip igmp snooping[no] ip igmp snooping { holddown-timer <timer> | cc-mode | m2rib-max-omfs <omf-count> |m2rib-max-omf-routes <omf-route-count> | m2rib-max-routes <route-count> | m2rib-max-buffers <buf-count>}
Syntax Description
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
(Optional) Negate a command or set its defaultsno
Intitial holddown period after switchover/restartholddown-timer
Enter MFDM congestion-control modecc-mode
Number of OMF entries in M2RIB bufferm2rib-max-omfs
Number of route entries in M2RIB bufferm2rib-max-routes
Number of omf route entries in M2RIB bufferm2rib-max-omf-routes
Number of update buffers with M2RIBm2rib-max-buffers
Delay (in secs)timer
omf-count
route-count
buf-count
omf-route-count
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2028
I Commandsip igmp snooping
Page 2173
ip igmp snooping access-group[no] ip igmp snooping access-group <route-map-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP configuration commandsigmp
Configures IGMP Snoopingsnooping
Configures filter policy for groups mentioned in route-mapaccess-group
route-map nameroute-map-name
Command Mode
• /exec/configure/vlan-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2029
I Commandsip igmp snooping access-group
Page 2174
ip igmp snooping disable-nve-static-router-port[no] ip igmp snooping disable-nve-static-router-port
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Disable NVE as a static router portdisable-nve-static-router-port
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2030
I Commandsip igmp snooping disable-nve-static-router-port
Page 2175
ip igmp snooping disable-nve-static-router-port[no] ip igmp snooping disable-nve-static-router-port
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Disable NVE as a static router portdisable-nve-static-router-port
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2031
I Commandsip igmp snooping disable-nve-static-router-port
Page 2176
ip igmp snooping event-history igmp-snoop-internal[no] ip igmp snooping event-history igmp-snoop-internal { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Configure event-history buffersevent-history
Internal events for IGMP-snoopigmp-snoop-internal
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2032
I Commandsip igmp snooping event-history igmp-snoop-internal
Page 2177
ip igmp snooping event-history mfdm-sum[no] ip igmp snooping event-history mfdm-sum { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Configure event-history buffersevent-history
MFDM-SUM events for IGMP-snoopmfdm-sum
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2033
I Commandsip igmp snooping event-history mfdm-sum
Page 2178
ip igmp snooping event-history mfdm[no] ip igmp snooping event-history mfdm { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Configure event-history buffersevent-history
MFDM events for IGMP-snoopmfdm
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2034
I Commandsip igmp snooping event-history mfdm
Page 2179
ip igmp snooping event-history rib[no] ip igmp snooping event-history rib { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Configure event-history buffersevent-history
RIB events for IGMP-snooprib
Configure siazesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2035
I Commandsip igmp snooping event-history rib
Page 2180
ip igmp snooping event-history vlan-events[no] ip igmp snooping event-history vlan-events { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Configure event-history buffersevent-history
VLAN/BD events for IGMP-snoopvlan-events
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2036
I Commandsip igmp snooping event-history vlan-events
Page 2181
ip igmp snooping event-history vlan[no] ip igmp snooping event-history vlan { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Configure event-history buffersevent-history
VLAN/BD events for IGMP-snoopvlan
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2037
I Commandsip igmp snooping event-history vlan
Page 2182
ip igmp snooping event-history vpc[no] ip igmp snooping event-history vpc { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Configure event-history buffersevent-history
VPC events for IGMP-snoopvpc
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2038
I Commandsip igmp snooping event-history vpc
Page 2183
ip igmp snooping group-timeout[no] ip igmp snooping group-timeout { <timeout> | never }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP configuration commandsigmp
Configures IGMP Snoopingsnooping
Configures group membership timeout in VLAN/BDgroup-timeout
Timeout in minutestimeout
Never expire ports from group membershipnever
Command Mode
• /exec/configure/vlan-config /exec/configure/bdomain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2039
I Commandsip igmp snooping group-timeout
Page 2184
ip igmp snooping group-timeout[no] ip igmp snooping group-timeout { <timeout> | never }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP configuration commandsigmp
Configures IGMP Snoopingsnooping
Configures group membership timeout in all VLAN/BDsgroup-timeout
Timeout in minutestimeout
Never expire ports from group membershipnever
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2040
I Commandsip igmp snooping group-timeout
Page 2185
ip igmp snooping last-member-query-interval{ { no ip igmp snooping last-member-query-interval [ <interval> ] } | { ip igmp snoopinglast-member-query-interval <interval> } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP configuration commandsigmp
Configures IGMP Snoopingsnooping
Configures interval between group-specific Query transmissionslast-member-query-interval
(Optional) Interval in secondsinterval
Command Mode
• /exec/configure/vlan-config /exec/configure/bdomain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2041
I Commandsip igmp snooping last-member-query-interval
Page 2186
ip igmp snooping link-local-groups-suppression[no] ip igmp snooping link-local-groups-suppression
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP configuration commandsigmp
Configures IGMP Snoopingsnooping
Configures VLAN/BD link-local groups suppressionlink-local-groups-suppression
Command Mode
• /exec/configure/vlan-config /exec/configure/bdomain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2042
I Commandsip igmp snooping link-local-groups-suppression
Page 2187
ip igmp snooping link-local-groups-suppression[no] ip igmp snooping link-local-groups-suppression
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Configures Global link-local groups suppressionlink-local-groups-suppression
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2043
I Commandsip igmp snooping link-local-groups-suppression
Page 2188
ip igmp snooping many-to-one-enhance[no] ip igmp snooping many-to-one-enhance
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Enable many to one optimization for n3500 platformmany-to-one-enhance
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2044
I Commandsip igmp snooping many-to-one-enhance
Page 2189
ip igmp snooping max-gq-miss{ { no ip igmp snooping max-gq-miss } | { ip igmp snooping max-gq-miss <count> } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Configure general query miss countmax-gq-miss
Max number of GQ misses allowedcount
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2045
I Commandsip igmp snooping max-gq-miss
Page 2190
ip igmp snooping mrouter vpc-peer-link[no] ip igmp snooping mrouter vpc-peer-link
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Configures static multicast router interfacemrouter
Specify vpc-peer-link as static mrouter for all VLAN/BDsvpc-peer-link
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2046
I Commandsip igmp snooping mrouter vpc-peer-link
Page 2191
ip igmp snooping proxy-leave use-group-address{ { ip igmp snooping proxy-leave use-group-address } | { no ip igmp snooping proxy-leave use-group-address} }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP configuration commandsigmp
Configures IGMP Snoopingsnooping
Proxy Leaveproxy-leave
Use group address for proxy leaveuse-group-address
Command Mode
• /exec/configure/vlan-config /exec/configure/bdomain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2047
I Commandsip igmp snooping proxy-leave use-group-address
Page 2192
ip igmp snooping proxy general-queries[no] ip igmp snooping proxy general-queries [ mrt <mrt> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP configuration commandsigmp
Configures IGMP Snoopingsnooping
Configures IGMP snooping proxyproxy
Configures proxy for general-queriesgeneral-queries
(Optional) Configure max-response-time for the switch's proxygeneral-queries
mrt
(Optional) MRT in secondsmrt
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2048
I Commandsip igmp snooping proxy general-queries
Page 2193
ip igmp snooping proxy general-queries[no] ip igmp snooping proxy general-queries [ mrt <mrt> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP configuration commandsigmp
Configures IGMP Snoopingsnooping
Configures IGMP snooping proxyproxy
Configures proxy for general-queriesgeneral-queries
(Optional) Configure max-response-time for the switch's proxygeneral-queries
mrt
(Optional) MRT in secondsmrt
Command Mode
• /exec/configure/vlan-config /exec/configure/bdomain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2049
I Commandsip igmp snooping proxy general-queries
Page 2194
ip igmp snooping report-flood all{ { ip igmp snooping report-flood { all | interface <interface> } } | { no ip igmp snooping report-flood { all |interface <interface> } } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP configuration commandsigmp
Configures IGMP Snoopingsnooping
Configures Report flooding on a VLANreport-flood
Specify interface for report floodinginterface
Flood on ALL active ports of VLANall
Interface nameinterface
Command Mode
• /exec/configure/vlan-config /exec/configure/bdomain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2050
I Commandsip igmp snooping report-flood all
Page 2195
ip igmp snooping report-suppression{ { no ip igmp snooping report-suppression } | { ip igmp snooping report-suppression } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP configuration commandsigmp
Configures IGMP Snoopingsnooping
Configures IGMPv1/IGMPv2 Report Suppression for the VLAN/BDreport-suppression
Command Mode
• /exec/configure/vlan-config /exec/configure/bdomain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2051
I Commandsip igmp snooping report-suppression
Page 2196
ip igmp snooping report-suppression{ { no ip igmp snooping report-suppression } | { ip igmp snooping report-suppression } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Configures Global IGMPv1/IGMPv2 Report Suppressionreport-suppression
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2052
I Commandsip igmp snooping report-suppression
Page 2197
ip igmp snooping report prefix interface{ [ no ] ip igmp snooping { report-policy | access-group } { prefix-list | route-map } <pname> interface<interface> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP configuration commandsigmp
Configures IGMP Snoopingsnooping
IGMP Report Policyreport-policy
IGMP access-groupaccess-group
IPv4 Prefix-List Policyprefix-list
Route-Map Policyroute-map
Policy Name Namepname
Specify interface for filteringinterface
Interface nameinterface
Command Mode
• /exec/configure/vlan-config /exec/configure/bdomain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2053
I Commandsip igmp snooping report prefix interface
Page 2198
ip igmp snooping syslog-threshold{ ip igmp snooping syslog-threshold <percentage> } | { no ip igmp snooping syslog-threshold }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP configuration commandsigmp
Configures IGMP Snoopingsnooping
IGMP SNOOPING table syslog thresholdsyslog-threshold
Percentagepercentage
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2054
I Commandsip igmp snooping syslog-threshold
Page 2199
ip igmp snooping v3-report-suppression{ { no ip igmp snooping v3-report-suppression } | { ip igmp snooping v3-report-suppression } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Configures IGMP Snoopingsnooping
Configures Global IGMPv3 Report Suppression and Proxy Reportingv3-report-suppression
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2055
I Commandsip igmp snooping v3-report-suppression
Page 2200
ip igmp snooping v3-report-suppression{ { no ip igmp snooping v3-report-suppression } | { ip igmp snooping v3-report-suppression } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP configuration commandsigmp
Configures IGMP Snoopingsnooping
Configures IGMPv3 Report Suppression and Proxy Reporting for theVLAN/BD
v3-report-suppression
Command Mode
• /exec/configure/vlan-config /exec/configure/bdomain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2056
I Commandsip igmp snooping v3-report-suppression
Page 2201
ip igmp spoof-check[no] ip igmp spoof-check
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Enable spoof check for IGMPspoof-check
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2057
I Commandsip igmp spoof-check
Page 2202
ip igmp ssm-translate[no] ip igmp ssm-translate <group> <source>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP global configuration commandsigmp
Translate IGMPv1/v2 reports to (S,G) route entriesssm-translate
IP Multicast group rangegroup
IP Multicast address sourcesource
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2058
I Commandsip igmp ssm-translate
Page 2203
ip igmp startup-query-count{ { no ip igmp startup-query-count [ <count> ] } | { ip igmp startup-query-count <count> } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Configures number of queries sent at startupstartup-query-count
(Optional) Count valuecount
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2059
I Commandsip igmp startup-query-count
Page 2204
ip igmp startup-query-interval{ { no ip igmp startup-query-interval [ <interval> ] } | { ip igmp startup-query-interval <interval> } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Configures query interval at startupstartup-query-interval
(Optional) Interval in secondsinterval
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2060
I Commandsip igmp startup-query-interval
Page 2205
ip igmp state-limit{ { ip igmp state-limit <max-states> [ reserved <route-map-name> <max-reserved> ] } | { no ip igmp state-limit[ <max-states> [ reserved <route-map-name> <max-reserved> ] ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Configures State limitstate-limit
Maximum states allowedmax-states
(Optional) Reserve the states using route-mapreserved
(Optional) Route-map nameroute-map-name
(Optional) Maximum (*,G)/(S,G) entires allowed on the interfacemax-reserved
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2061
I Commandsip igmp state-limit
Page 2206
ip igmp static[no] ip igmp { static-group | static-oif } { { <group> [ source <source> ] } | { route-map <route-map-name>} }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Configures static oif for a multicast forwarding entrystatic-group
Configures static oif for a multicast forwarding entrystatic-oif
Multicast group IP addressgroup
(Optional) Configures source address for IGMPv3 (S,G) Channelsource
(Optional) Source IP addresssource
Static group policyroute-map
Route-map nameroute-map-name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2062
I Commandsip igmp static
Page 2207
ip igmp suppress v3-gsq[no] ip igmp suppress v3-gsq
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Suppresssuppress
v3 GSQv3-gsq
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2063
I Commandsip igmp suppress v3-gsq
Page 2208
ip igmp syslog-threshold{ ip igmp syslog-threshold <percentage> } | { no ip igmp syslog-threshold }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP related eventsigmp
IGMP table syslog thresholdsyslog-threshold
Percentagepercentage
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2064
I Commandsip igmp syslog-threshold
Page 2209
ip igmp version{ { no ip igmp version [ <version> ] } | { ip igmp version <version> } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
IGMP interface configuration commandsigmp
Configures IGMP version number for interfaceversion
(Optional) Version number valueversion
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2065
I Commandsip igmp version
Page 2210
ip lisp alt-vrf{ { [ no ] ip lisp alt-vrf { <vrf-name> | <vrf-known-name> } } | { [ no ] ipv6 lisp alt-vrf { <vrf-name> |<vrf-known-name> } } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Activate LISP-ALT functionality in VRFalt-vrf
VRF namevrf-name
Known VRF namevrf-known-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2066
I Commandsip lisp alt-vrf
Page 2211
ip lisp database-mapping dynamic priority weight{ [ no ] ip lisp database-mapping <eid-prefix> { <locator> | <locator6> | { dynamic <interface> } } priority<priority> weight <weight> } | { no ip lisp database-mapping <eid-prefix> { <locator> | <locator6> | { dynamic<interface> } } } | { [ no ] ipv6 lisp database-mapping <eid-prefix6> { <locator> | <locator6> | { dynamic<interface> } } priority <priority> weight <weight> } | { no ipv6 lisp database-mapping <eid-prefix6> {<locator> | <locator6> | { dynamic <interface> } } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures Locator addresses for an ETRdatabase-mapping
IP EID-prefix to advertise locators foreid-prefix
IP address of loopback or other ETR loopback interfacelocator
Get locator dynamicallydynamic
Interface to learn dynamic locatorinterface
Configures which Locators from a set are preferredpriority
Lower priority Locator takes preferencepriority
Traffic load-spreading among Locatorsweight
Specified in a percentage from 0 to 100weight
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2067
I Commandsip lisp database-mapping dynamic priority weight
Page 2212
ip lisp disable-spoof-alert[no] { ip | ipv6 } lisp disable-spoof-alert
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Disable spoof-alert checking for Map-Repliesdisable-spoof-alert
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2068
I Commandsip lisp disable-spoof-alert
Page 2213
ip lisp etr[no] { ip | ipv6 } lisp etr
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures LISP Egress Tunnel Router (ETR) parametersetr
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2069
I Commandsip lisp etr
Page 2214
ip lisp etr accept-map-request-mapping{ { [ no ] ip lisp etr accept-map-request-mapping [ verify ] } | { [ no ] ipv6 lisp etr accept-map-request-mapping[ verify ] } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Configures LISP Egress Tunnel Router (ETR) parametersetr
LISP global configuration commandslisp
Configures an ETR to cache mappings received from Map-Requestmessages
accept-map-request-mapping
(Optional) Send Map-Request back to Map-Request originator of aMapping Data Record
verify
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2070
I Commandsip lisp etr accept-map-request-mapping
Page 2215
ip lisp etr glean-mapping{ { [ no ] ip lisp etr glean-mapping [ verify ] } | { [ no ] ipv6 lisp etr glean-mapping } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Configures LISP Egress Tunnel Router (ETR) parametersetr
LISP global configuration commandslisp
Glean locator mapping from outer DA for inner DA EIDglean-mapping
(Optional) Send Map-Request to ITR to verify data gleaningverify
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2071
I Commandsip lisp etr glean-mapping
Page 2216
ip lisp etr map-cache-ttl{ [ no ] ip lisp etr map-cache-ttl <minutes> } | { no ip lisp etr map-cache-ttl } | { [ no ] ipv6 lisp etr map-cache-ttl<minutes> } | { no ipv6 lisp etr map-cache-ttl }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Configures LISP Egress Tunnel Router (ETR) parametersetr
LISP global configuration commandslisp
Configures TTL for Map-Reply messagesmap-cache-ttl
Time-to-Live in units of minutesminutes
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2072
I Commandsip lisp etr map-cache-ttl
Page 2217
ip lisp etr map-register-ttl{ [ no ] ip lisp etr map-register-ttl <minutes> } | { no ip lisp etr map-register-ttl } | { [ no ] ipv6 lisp etrmap-register-ttl <minutes> } | { no ipv6 lisp etr map-register-ttl }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Configures LISP Egress Tunnel Router (ETR) parametersetr
LISP global configuration commandslisp
Configures TTL for Map-Register messagesmap-register-ttl
Time-to-Live in units of minutesminutes
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2073
I Commandsip lisp etr map-register-ttl
Page 2218
ip lisp etr map-server key{ { [ no ] ip lisp etr map-server { <ms> | <ms6> } [ key-type { sha1 | sha2 } ] key <key> } | { [ no ] ipv6 lispetr map-server { <ms> | <ms6> } [ key-type { sha1 | sha2 } ] key <key> } | { [ no ] ip lisp etr map-server {<ms> | <ms6> } proxy-reply } | { [ no ] ipv6 lisp etr map-server { <ms> | <ms6> } proxy-reply } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures LISP Egress Tunnel Router (ETR) parametersetr
To interact with Map-Servermap-server
Address of IPv4 map-serverms
(Optional) Authentication key type, either sha1 or sha2key-type
(Optional) Use sha1 authenication in Map-Register messagessha1
(Optional) Use sha2 authenication in Map-Register messagessha2
Authentication key used with Map-Serverkey
SHA-1 password keykey
Request Map-Server to send Map-Replies on behalf of siteproxy-reply
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2074
I Commandsip lisp etr map-server key
Page 2219
ip lisp hardware-forwarding[no] { ip | ipv6 } lisp hardware-forwarding
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Enable/disable Nexus 7K hardware forwardinghardware-forwarding
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2075
I Commandsip lisp hardware-forwarding
Page 2220
ip lisp itr-etr[no] { ip | ipv6 } lisp itr-etr
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures both LISP ITR and ETR functionalityitr-etr
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2076
I Commandsip lisp itr-etr
Page 2221
ip lisp itr[no] { ip | ipv6 } lisp itr
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures LISP Ingress Tunnel Router (ITR) parametersitr
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2077
I Commandsip lisp itr
Page 2222
ip lisp itr map-resolver{ [ no ] { ip | ipv6 } lisp itr map-resolver { <mr> | <mr6> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures LISP Ingress Tunnel Router (ITR) parametersitr
To interact with Map-Resolvermap-resolver
Address of IPv4 map-servermr
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2078
I Commandsip lisp itr map-resolver
Page 2223
ip lisp itr send-data-probe{ { [ no ] ip lisp itr send-data-probe } | { [ no ] ipv6 lisp itr send-data-probe } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures LISP Ingress Tunnel Router (ITR) parametersitr
Send a Data-Probe instead of Map-Request on the LISP-ALT topologysend-data-probe
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2079
I Commandsip lisp itr send-data-probe
Page 2224
ip lisp locator-vrf{ { [ no ] ip lisp locator-vrf { <vrf-name> | <vrf-known-name> } } | { [ no ] ipv6 lisp locator-vrf { <vrf-name>| <vrf-known-name> } } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configure what VRF to use for locator command referenceslocator-vrf
VRF namevrf-name
Known VRF namevrf-known-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2080
I Commandsip lisp locator-vrf
Page 2225
ip lisp locator reachability exclude[no] { ip | ipv6 } lisp locator reachability { exclude-default | minimum-mask-length <minmask> }
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configure IP featuresip
Configure IPv6 featuresipv6
Configure locator parameterslocator
Configure reachability parametersreachability
Exclude default route to reach remote locatorsexclude-default
Exclude routes coarser than the given mask lengthminimum-mask-length
Minimum mask length for the routes to locatorsminmask
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2081
I Commandsip lisp locator reachability exclude
Page 2226
ip lisp map-cache-limit[no] { ip | ipv6 } lisp map-cache-limit <limit> [ reserve-list <prefix-list> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures maximum size of map-cachemap-cache-limit
Maximum number of map-cache entrieslimit
(Optional) EID-prefixes guaranteed to be stored in map-cachereserve-list
(Optional) Reference to prefix-list nameprefix-list
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2082
I Commandsip lisp map-cache-limit
Page 2227
ip lisp map-cache drop native-forward map-request priorityweight
{ { [ no ] ip lisp map-cache <eid-prefix> { drop | native-forward | map-request | { { <locator> | <locator6> }priority <priority> weight <weight> [ down ] } } } | { [ no ] ipv6 lisp map-cache <eid-prefix6> { drop |native-forward | map-request | { { <locator6> | <locator> } priority <priority> weight <weight> [ down ] } }} }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures static EID-to-RLOC mappings for an ITRmap-cache
IP EID-prefix for RLOC static mappingeid-prefix
IP address of loopback or other ETR loopback interfacelocator
Configures which Locators from a set are preferredpriority
Lower priority Locator takes preferencepriority
Traffic load-spreading among Locatorsweight
Specified in a percentage from 0 to 100weight
(Optional) Set state to down for RLOCdown
Drop packets that match this map-cache entrydrop
Natively forward packets that match his map-cache entrynative-forward
Send Map-Request for LISP destination EIDmap-request
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2083
I Commandsip lisp map-cache drop native-forward map-request priority weight
Page 2228
ip lisp map-request-source{ [ no ] ip lisp map-request-source <source> } | { no ip lisp map-request-source } | { [ no ] ipv6 lispmap-request-source <source6> } | { no ipv6 lisp map-request-source }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures source address for Map-Request messagemap-request-source
Source address for IPv4 Map-Request messagesource
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2084
I Commandsip lisp map-request-source
Page 2229
ip lisp map-resolver{ [ no ] { ip | ipv6 } lisp map-resolver }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures LISP Map Resolver functionalitymap-resolver
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2085
I Commandsip lisp map-resolver
Page 2230
ip lisp map-server{ [ no ] { ip | ipv6 } lisp map-server }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures LISP Map Server functionalitymap-server
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2086
I Commandsip lisp map-server
Page 2231
ip lisp map-server try-map-cache{ [ no ] { ip | ipv6 } lisp map-server try-map-cache }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures LISP Map Server functionalitymap-server
Forward Map-Request to RLOCs from map-cache when siteconfiguration does not exist
try-map-cache
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2087
I Commandsip lisp map-server try-map-cache
Page 2232
ip lisp multicast[no] ip lisp multicast
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
LISP global configuration commandslisp
Configures LISP to carry multicast traffic, when ITR or ETR functionis enabled
multicast
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2088
I Commandsip lisp multicast
Page 2233
ip lisp nat-traversal[no] { ip | ipv6 } lisp nat-traversal
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP interface configuration commandslisp
Send Echo messages to Map-Server to get global locatornat-traversal
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2089
I Commandsip lisp nat-traversal
Page 2234
ip lisp ntr[no] ip lisp ntr <locator>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
LISP global configuration commandslisp
Configures LISP NAT Tunnel Router (NTR)ntr
Local IP address in locator namespacelocator
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2090
I Commandsip lisp ntr
Page 2235
ip lisp null0-is-alt-miss[no] { ip | ipv6 } lisp null0-is-alt-miss
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Consider a ALT route with null0 next-hop as a lookup missnull0-is-alt-miss
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2091
I Commandsip lisp null0-is-alt-miss
Page 2236
ip lisp proxy-etr{ { [ no ] ip lisp proxy-etr } | { [ no ] ipv6 lisp proxy-etr } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures a Proxy ETR (PETR)proxy-etr
lisp
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2092
I Commandsip lisp proxy-etr
Page 2237
ip lisp proxy-itr{ { [ no ] ip lisp proxy-itr { <local-rloc> | <local-rloc6> } + } | { [ no ] ipv6 lisp proxy-itr { <local-rloc> |<local-rloc6> } + } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Configures a Proxy ITR (PTR)proxy-itr
Local IP address in locator namespacelocal-rloc
lisp
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2093
I Commandsip lisp proxy-itr
Page 2238
ip lisp short-map-cache-ttl{ [ no ] { ip | ipv6 } lisp short-map-cache-ttl }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Sets both positive and negative TTL in Map-Reply to 1 minuteshort-map-cache-ttl
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2094
I Commandsip lisp short-map-cache-ttl
Page 2239
ip lisp shortest-eid-prefix-length{ { [ no ] ip lisp shortest-eid-prefix-length <pl> } | { [ no ] ipv6 lisp shortest-eid-prefix-length <pl6> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Do not accept EID-prefixes shorter than configured valueshortest-eid-prefix-length
IPv4 EID-prefix lengthpl
IPv6 EID-prefix lengthpl6
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2095
I Commandsip lisp shortest-eid-prefix-length
Page 2240
ip lisp source-locator{ [ no ] { ip | ipv6 } lisp source-locator <interface> [ secondary ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP interface configuration commandslisp
Select source locator when destination locator uses this interfacesource-locator
Use primary address from interface as source locatorinterface
(Optional) Use secondary address on interface as source locatorsecondary
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2096
I Commandsip lisp source-locator
Page 2241
ip lisp translate inside outside{ { [ no ] ip lisp translate inside <nrEID> outside <rEID> } | { [ no ] ipv6 lisp translate inside <nrEID6>outside <rEID6> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Translate source address on ITR or destination address on ETRtranslate
Site-based non-routable EIDinside
IPv4 inside addressnrEID
External-based routable EIDoutside
IPv4 outside addressrEID
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2097
I Commandsip lisp translate inside outside
Page 2242
ip lisp use-bgp-locators[no] { ip | ipv6 } lisp use-bgp-locators [ route-map <rmap-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Use next-hops from BGP as locators for map-cache entriesuse-bgp-locators
(Optional) Route-map applied to on-demand routes.route-map
(Optional) Route-map namermap-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2098
I Commandsip lisp use-bgp-locators
Page 2243
ip lisp use-petr priority weight[no] { ip | ipv6 } lisp use-petr { <petr> | <petr6> } priority <priority> weight <weight>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
LISP global configuration commandslisp
Encapsulate to Proxy ETR for matching forward-native entryuse-petr
IPv4 locator address of PETRpetr
Configures which Locators from a set are preferredpriority
Lower priority Locator takes preferencepriority
Traffic load-spreading among Locatorsweight
Specified in a percentage from 0 to 100weight
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2099
I Commandsip lisp use-petr priority weight
Page 2244
ip load-sharing address[no] ip load-sharing address { source-destination [ port source-destination2 | gre | gre-outer | gtpu ] | destinationport2 destination2 | source } { [ rotate <rotate> ] | [ concatenation ] } + [ universal-id <random-seed> ] | noip load-sharing address
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
ECMP load-sharingload-sharing
Configure source/destination addresses, port numbers and hashaddress
Use both source and destination values for addresssource-destination
(Optional) Use source-destination value for portport
(Optional) Use source-destination value for gre-keygre
(Optional) Use outer IPv4 header fields for GRE tunnel hashinggre-outer
(Optional) Use GTPU TEID value for port source-destinationgtpu
(Optional) Use both source and destination values for portsource-destination2
Use destination addressdestination
Use destination value for portport2
Use destination portdestination2
Use source addresssource
(Optional) Offset to be used in the hashrotate
(Optional) Value used for offset, default value is 32rotate
(Optional) Enable/Disable concatenationconcatenation
(Optional) Universal-id to randomize hash functions for load-balanceuniversal-id
(Optional) Value used to randomize hashrandom-seed
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2100
I Commandsip load-sharing address
Page 2245
ip local-proxy-arp{ ip local-proxy-arp [ no-hw-flooding ] | no ip local-proxy-arp [ no-hw-flooding ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure local proxy ARPlocal-proxy-arp
(Optional) Configure local proxy ARP without hardware floodingno-hw-flooding
Command Mode
• /exec/configure/if-igp /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2101
I Commandsip local-proxy-arp
Page 2246
ip local policy route-mapip local policy route-map <route-map-name> | no ip local policy route-map [ <route-map-name> |<route-map-name> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure local PBR featurelocal
Configure PBR featurepolicy
Route-map for PBRroute-map
Route-map nameroute-map-name
(Optional) Route-map nameroute-map-name
(Optional) Known route-map nameroute-map-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2102
I Commandsip local policy route-map
Page 2247
ip mfwd event-history cli[no] ip mfwd event-history cli { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configures Global IP Multicast Forwardingmfwd
Configure event-history buffersevent-history
CLI events for MCASTFWDcli
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2103
I Commandsip mfwd event-history cli
Page 2248
ip mfwd event-history l2[no] ip mfwd event-history l2 { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configures Global IP Multicast Forwardingmfwd
Configure event-history buffersevent-history
Layer2 events for MCASTFWDl2
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2104
I Commandsip mfwd event-history l2
Page 2249
ip mfwd event-history nbm[no] ip mfwd event-history nbm { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configures Global IP Multicast Forwardingmfwd
Configure event-history buffersevent-history
NBM events for MCASTFWDnbm
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2105
I Commandsip mfwd event-history nbm
Page 2250
ip mfwd event-history packet[no] ip mfwd event-history packet { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configures Global IP Multicast Forwardingmfwd
Configure event-history buffersevent-history
Packet events for Multicast forwardingpacket
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2106
I Commandsip mfwd event-history packet
Page 2251
ip mfwd event-history vrf[no] ip mfwd event-history vrf { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configures Global IP Multicast Forwardingmfwd
Configure event-history buffersevent-history
VRF events for MCASTFWDvrf
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2107
I Commandsip mfwd event-history vrf
Page 2252
ip mfwd mstatic register[no] ip mfwd mstatic register
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configures Global IP Multicast Forwardingmfwd
Static Multicast Routemstatic
Registerregister
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2108
I Commandsip mfwd mstatic register
Page 2253
ip mroute[no] ip mroute { <ip-addr> <ip-mask> | <ip-prefix> } { { <next-hop> | <nh-prefix> } | <interface> } [ <pref>] [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure multicast RPF static routemroute
IP prefix in format i.i.i.iip-addr
IP network mask in format m.m.m.mip-mask
IP prefix and network mask length in format x.x.x.x/mip-prefix
IP next-hop address in format i.i.i.inext-hop
IP next-hop prefix in format i.i.i.i/mnh-prefix
Interface for interface static multicast routesinterface
(Optional) Route preferencepref
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2109
I Commandsip mroute
Page 2254
ip msdp descriptionip msdp description <peer-address> <text> | no ip msdp description <peer-address> [ <text> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure MSDP description for peerdescription
IP address of MSDP peerpeer-address
Text descriptiontext
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2110
I Commandsip msdp description
Page 2255
ip msdp event-history cli[no] ip msdp event-history cli { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure event-history bufferevent-history
CLI logs for MSDPcli
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2111
I Commandsip msdp event-history cli
Page 2256
ip msdp event-history events[no] ip msdp event-history events { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure event-history bufferevent-history
Peer events for MSDPevents
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2112
I Commandsip msdp event-history events
Page 2257
ip msdp event-history routes[no] ip msdp event-history routes { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure event-history bufferevent-history
Route logs for MSDProutes
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2113
I Commandsip msdp event-history routes
Page 2258
ip msdp event-history tcp[no] ip msdp event-history tcp { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure event-history bufferevent-history
TCP logs for MSDPtcp
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2114
I Commandsip msdp event-history tcp
Page 2259
ip msdp flush-routes[no] ip msdp flush-routes
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Remove routes when restarting MSDPflush-routes
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2115
I Commandsip msdp flush-routes
Page 2260
ip msdp group-limit source[no] ip msdp group-limit <limit> source <sprefix>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Limit the number of groups per sourcegroup-limit
Limit on number of groupslimit
Sources to limit groups tosource
Prefix to match sources againstsprefix
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2116
I Commandsip msdp group-limit source
Page 2261
ip msdp keepaliveip msdp keepalive <peer-address> <interval> <timeout> | no ip msdp keepalive <peer-address> [ <interval><timeout> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure MSDP keepalive parameters for peerkeepalive
IP address of MSDP peerpeer-address
Keepalive interval in secondsinterval
Keepalive timeout in secondstimeout
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2117
I Commandsip msdp keepalive
Page 2262
ip msdp mesh-groupip msdp mesh-group <peer-address> <name> | no ip msdp mesh-group <peer-address> [ <name> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure member of mesh-groupmesh-group
Name of mesh-groupname
IP address of MSDP peer in mesh-grouppeer-address
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2118
I Commandsip msdp mesh-group
Page 2263
ip msdp originator-idip msdp originator-id <interface> | no ip msdp originator-id [ <interface> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure alternative router-id for MSDPoriginator-id
Use IP address of interface for originator-idinterface
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2119
I Commandsip msdp originator-id
Page 2264
ip msdp passwordip msdp password <peer-address> <password> | no ip msdp password <peer-address> [ <password> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure MD5 authentication passwordpassword
IP address of MSDP peerpeer-address
MD5 passwordpassword
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2120
I Commandsip msdp password
Page 2265
ip msdp peer connect-source{ { ip msdp peer <peer-address> connect-source <interface> [ remote-as <asn> ] } | { no ip msdp peer<peer-address> [ connect-source <interface> ] [ remote-as <asn> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure MSDP peerpeer
IP address of MSDP peerpeer-address
Configure local IP address for TCP connectionconnect-source
Use IP address of interface for peer addressinterface
(Optional) Configure remote Autonomous System Numberremote-as
(Optional) AS numberasn
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2121
I Commandsip msdp peer connect-source
Page 2266
ip msdp reconnect-intervalip msdp reconnect-interval <interval> | no ip msdp reconnect-interval [ <interval> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure connection reconnect intervalreconnect-interval
Interval in secondsinterval
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2122
I Commandsip msdp reconnect-interval
Page 2267
ip msdp redistribute[no] ip msdp redistribute [ route-map <route-map-name> | prefix-list <prefix-list-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure SA policy for all MSDP peerredistribute
(Optional) route-map policyroute-map
(Optional) Route-map nameroute-map-name
(Optional) Prefix list policyprefix-list
(Optional) Name of prefix-listprefix-list-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2123
I Commandsip msdp redistribute
Page 2268
ip msdp sa-intervalip msdp sa-interval <interval> | no ip msdp sa-interval [ <interval> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure Source-Active message transmission intervalsa-interval
Interval in secondsinterval
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2124
I Commandsip msdp sa-interval
Page 2269
ip msdp sa-limitip msdp sa-limit <peer-address> <limit> | no ip msdp sa-limit <peer-address> [ <limit> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure maximum (S,G) entries allowedsa-limit
Number of (S,G) entrieslimit
IP address of MSDP peer in mesh-grouppeer-address
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2125
I Commandsip msdp sa-limit
Page 2270
ip msdp sa-policy in[no] ip msdp sa-policy <peer-address> { <route-map-name> | prefix-list <prefix-list-name> | <rtr_pol_name>} in
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure SA policy for MSDP peersa-policy
Prefix list policyprefix-list
Input policyin
IP address of MSDP peer for SA policypeer-address
Route-map nameroute-map-name
Name of prefix-listprefix-list-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2126
I Commandsip msdp sa-policy in
Page 2271
ip msdp sa-policy out[no] ip msdp sa-policy <peer-address> { <route-map-name> | prefix-list <prefix-list-name> | <rtr_pol_name>} out
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Configure SA policy for MSDP peersa-policy
Prefix list policyprefix-list
Output policyout
IP address of MSDP peer for SA policypeer-address
Route-map nameroute-map-name
Name of prefix-listprefix-list-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2127
I Commandsip msdp sa-policy out
Page 2272
ip msdp shutdownip msdp shutdown <peer-address> | no ip msdp shutdown <peer-address>
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
MSDP global configuration commandsmsdp
Administratively shut down peershutdown
IP address of MSDP peerpeer-address
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2128
I Commandsip msdp shutdown
Page 2273
ip mtu eigrp{ { { ip | ipv6 } mtu eigrp <eigrp-ptag> <mtu> } | { no { ip | ipv6 } mtu eigrp <eigrp-ptag> [ <mtu> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Set Max Packet Size to be used by EIGRPmtu
EIGRP interface configuration commandseigrp
Process tageigrp-ptag
Interface MTUmtu
eigrp-ptag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2129
I Commandsip mtu eigrp
Page 2274
ip multicast multipath[no] ip multicast multipath { none | legacy | s-g-hash [ next-hop-based ] | nbm }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IP multicast global parametersmulticast
Configure ECMP multicast load splittingmultipath
Configure hash based on source and grouplegacy
Disable ECMP multicast load splittingnone
Configure hash based on source and group addresss-g-hash
(Optional) Configure hash based on source, group, next-hop addressnext-hop-based
Configure NBM controlled RPF interfacenbm
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2130
I Commandsip multicast multipath
Page 2275
ip multicast multipath resilient[no] ip multicast multipath resilient
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IP multicast global parametersmulticast
Configure ECMP multicast load splittingmultipath
Configure resilient RPF interfaceresilient
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2131
I Commandsip multicast multipath resilient
Page 2276
ip multicast overlay-distributed-dr[no] ip multicast overlay-distributed-dr
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure multicastmulticast
Configure node as Distributed-DRoverlay-distributed-dr
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2132
I Commandsip multicast overlay-distributed-dr
Page 2277
ip multicast overlay-spt-only[no] ip multicast overlay-spt-only
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure multicastmulticast
Enable L3-Overlay spt(shortest-path-tree) onlyoverlay-spt-only
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2133
I Commandsip multicast overlay-spt-only
Page 2278
ip multicast rpf select vrf group-list{ { ip multicast rpf select { vrf { <vrf-name> | <vrf-known-name> } group-list <prefix> } } | { no ip multicastrpf select { vrf { <vrf-name> | <vrf-known-name> } group-list <prefix> } } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure IP multicast global parametersmulticast
Configure RPF checkrpf
Configure VRF for RPF checkselect
VRF for RPF lookupvrf
VRF namevrf-name
Known VRF namevrf-known-name
Group range for RPF selectgroup-list
Group range prefixprefix
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2134
I Commandsip multicast rpf select vrf group-list
Page 2279
ip name-server[no] ip name-server { { <ipv4_0> | <ipv6_1> } [ { <ipv4_2> | <ipv6_3> } [ { <ipv4_4> | <ipv6_5> } [ {<ipv4_6> | <ipv6_7> } [ { <ipv4_8> | <ipv6_9> } [ { <ipv4_10> | <ipv6_11> } ] ] ] ] ] | { <ipv4_12> |<ipv6_13> } [ use-vrf { <vrf-name> | <vrf-known-name> } ] | { <ipv4_14> | <ipv6_15> } [ { <ipv4_16> |<ipv6_17> } [ use-vrf { <vrf-name> | <vrf-known-name> } ] ] | { <ipv4_18> | <ipv6_19> } [ { <ipv4_20> |<ipv6_21> } [ { <ipv4_22> | <ipv6_23> } [ use-vrf { <vrf-name> | <vrf-known-name> } ] ] ] | { <ipv4_24>| <ipv6_25> } [ { <ipv4_26> | <ipv6_27> } [ { <ipv4_28> | <ipv6_29> } [ { <ipv4_30> | <ipv6_31> } [use-vrf { <vrf-name> | <vrf-known-name> } ] ] ] ] | { <ipv4_32> | <ipv6_33> } [ { <ipv4_34> | <ipv6_35>} [ { <ipv4_36> | <ipv6_37> } [ { <ipv4_38> | <ipv6_39> } [ { <ipv4_40> | <ipv6_41> } [ use-vrf { <vrf-name>| <vrf-known-name> } ] ] ] ] ] | { <ipv4_42> | <ipv6_43> } [ { <ipv4_44> | <ipv6_45> } [ { <ipv4_46> |<ipv6_47> } [ { <ipv4_48> | <ipv6_49> } [ { <ipv4_50> | <ipv6_51> } [ { <ipv4_52> | <ipv6_53> } [ use-vrf{ <vrf-name> | <vrf-known-name> } ] ] ] ] ] ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Specify nameserver addressname-server
Enter an IPv4 addressipv4_0
(Optional) Enter an IPv4 addressipv4_2
(Optional) Enter an IPv4 addressipv4_4
(Optional) Enter an IPv4 addressipv4_6
(Optional) Enter an IPv4 addressipv4_8
(Optional) Enter an IPv4 addressipv4_10
Enter an IPv4 addressipv4_12
(Optional) Display per-VRF informationuse-vrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Enter an IPv4 addressipv4_14
(Optional) Enter an IPv4 addressipv4_16
Enter an IPv4 addressipv4_18
(Optional) Enter an IPv4 addressipv4_20
(Optional) Enter an IPv4 addressipv4_22
Enter an IPv4 addressipv4_24
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2135
I Commandsip name-server
Page 2280
(Optional) Enter an IPv4 addressipv4_26
(Optional) Enter an IPv4 addressipv4_28
(Optional) Enter an IPv4 addressipv4_30
Enter an IPv4 addressipv4_32
(Optional) Enter an IPv4 addressipv4_34
(Optional) Enter an IPv4 addressipv4_36
(Optional) Enter an IPv4 addressipv4_38
(Optional) Enter an IPv4 addressipv4_40
Enter an IPv4 addressipv4_42
(Optional) Enter an IPv4 addressipv4_44
(Optional) Enter an IPv4 addressipv4_46
(Optional) Enter an IPv4 addressipv4_48
(Optional) Enter an IPv4 addressipv4_50
(Optional) Enter an IPv4 addressipv4_52
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2136
I Commandsip name-server
Page 2281
ip nat inside[no] ip nat { inside | outside }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
NAT interface commandsnat
Inside interface for address translationinside
Outside interface for address translationoutside
Command Mode
• /exec/configure/if-port-channel /exec/configure/if-vlan /exec/configure/if-remote-ethernet/exec/configure/if-igp /exec/configure/if-routing
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2137
I Commandsip nat inside
Page 2282
ip nat inside source[no] ip nat inside source { { static <insideLocalIP> <insideGlobalIP> [ vrf <vrf-name> [ match-in-vrf ] ] [group <group-id> [ dynamic ] ] [ no-alias ] [ add-route ] } | { static { tcp | udp } <insideLocalIP><insideLocalPort> <insideGlobalIP> <insideGlobalPort> [ vrf <vrf-name> [match-in-vrf ] ] [ group <group-id>[ dynamic ] ] [ no-alias ] [ add-route ] } | { list <acl-name> } { pool <pool-name> [ vrf <vrf-name> [match-in-vrf ] ] [ overload ] | interface <globalAddrInterface> [ vrf <vrf-name> [ match-in-vrf ] ] overload }[ group <group-id> dynamic ] [ add-route ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
NAT configuration commandsnat
Inside address translationinside
Source address translationsource
Specify static local->global mappingstatic
Transmission Control Protocoltcp
User Datagram Protocoludp
Specify access list describing local addresseslist
Name pool of global addressespool
Specify interface for global addressinterface
(Optional) Specify vrfvrf
(Optional) Match incoming vrfmatch-in-vrf
(Optional) Do not create alias for this NAT-addressno-alias
(Optional) Dynamic twice NAT groupdynamic
Inside local IP addressinsideLocalIP
Local UDP/TCP portinsideLocalPort
Inside global IP addressinsideGlobalIP
Global UDP/TCP portinsideGlobalPort
(Optional) Specify group for the twice NATgroup
(Optional) Group ID for the twice NATgroup-id
Access-list-nameacl-name
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2138
I Commandsip nat inside source
Page 2283
Pool name for global addressespool-name
(Optional) Add a static route for outside local addressadd-route
(Optional) vrf namevrf-name
interface type and number in module/slot formatglobalAddrInterface
(Optional) Overload an address translationoverload
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2139
I Commandsip nat inside source
Page 2284
ip nat outside source[no] ip nat outside source { static <outsideGlobalIP> <outsideLocalIP> [ vrf <vrf-name> [ match-in-vrf ] ] [group <group-id> [ dynamic ] ] [ no-alias ] [ add-route ] | static { tcp | udp } <outsideGlobalIP><outsideGlobalPort> <outsideLocalIP> <outsideLocalPort> [ vrf <vrf-name> [ match-in-vrf ] ] [ group<group-id> [ dynamic ] ] [ no-alias ] [ add-route ] | list <acl-name> pool <pool-name> [ vrf <vrf-name> [match-in-vrf ] ] [ group <group-id> dynamic ] } [ add-route ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
NAT configuration commandsnat
Outside address translationoutside
Source address translationsource
Specify static global->local mappingstatic
Transmission Control Protocoltcp
User Datagram Protocoludp
Specify access list describing local addresseslist
Name pool of global addressespool
(Optional) Specify vrfvrf
(Optional) Match incoming vrfmatch-in-vrf
(Optional) Do not create alias for this NAT-addressno-alias
Outside global IP addressoutsideGlobalIP
Outside Global UDP/TCP portoutsideGlobalPort
Outside local IP addressoutsideLocalIP
Outside Local UDP/TCP portoutsideLocalPort
(Optional) Specify group for the twice NATgroup
(Optional) Dynamic twice NAT groupdynamic
(Optional) Group ID for the twice NATgroup-id
Access-list-nameacl-name
(Optional) vrf namevrf-name
Pool name for global addressespool-name
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2140
I Commandsip nat outside source
Page 2285
(Optional) Add a static route for outside local addressadd-route
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2141
I Commandsip nat outside source
Page 2286
ip nat pool netmaskip nat pool <pool-name> <start-ip> <end-ip> { netmask <netmask> | prefix-length <prefix-length> } [ no-alias] | no ip nat pool <pool-name> [ <start-ip> <end-ip> { netmask <netmask> | prefix-length <prefix-length> }]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
NAT configuration commandsnat
Define pool of addressespool
Specify the network masknetmask
Specify the prefix lengthprefix-length
(Optional) Do not create alias for these pool addressesno-alias
Pool namepool-name
Start IP addressstart-ip
End IP addressend-ip
Network masknetmask
Prefix lengthprefix-length
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2142
I Commandsip nat pool netmask
Page 2287
ip nat pool netmaskip nat pool <pool-name> { netmask <netmask> | prefix-length <prefix-length> } [ no-alias ]
Syntax Description
Configure IP featuresip
NAT configuration commandsnat
Define pool of addressespool
Specify the network masknetmask
Specify the prefix lengthprefix-length
(Optional) Do not create alias for these pool addressesno-alias
Pool namepool-name
Network masknetmask
Prefix lengthprefix-length
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2143
I Commandsip nat pool netmask
Page 2288
ip nat translation[no] ip nat translation { { { tcp-timeout | udp-timeout | icmp-timeout | timeout } <timeout> } | { finrst-timeout{ <fin_timeout> | never } | syn-timeout { <syn_timeout> | never } | timeout } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
NAT configuration commandsnat
NAT translation entry configurationtranslation
Specify timeout for NAT TCP flowstcp-timeout
Specify timeout for NAT UDP flowsudp-timeout
Specify timeout for NAT ICMP flowsicmp-timeout
Specify timeout for NAT TCP flows after a FIN or RSTfinrst-timeout
Specify timeout for NAT TCP flows after a SYN and no further datasyn-timeout
Specify timeout for dynamic NAT flowstimeout
Never timeoutnever
Timeout in secondstimeout
Timeout in secondsfin_timeout
Timeout in secondssyn_timeout
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2144
I Commandsip nat translation
Page 2289
ip nat translation creation-delay{ ip nat translation creation-delay <batch-timeout> } | { no ip nat translation creation-delay }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
NAT configuration commandsnat
NAT translation entry configurationtranslation
Translation entries creation delay due to batching before program totcam
creation-delay
0/250/500/750/1000batch-timeout
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2145
I Commandsip nat translation creation-delay
Page 2290
ip nat translation max-entriesip nat translation max-entries [ all-host ] <max> | no ip nat translation max-entries [ all-host ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
NAT configuration commandsnat
NAT translation entry configurationtranslation
Specify maximum number of NAT dynamic entriesmax-entries
(Optional) Specify maximum number of NAT entries for each hostall-host
Number of entriesmax
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2146
I Commandsip nat translation max-entries
Page 2291
ip nat translation sampling-timeout[no] ip nat translation sampling-timeout <timeout>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
NAT configuration commandsnat
NAT translation entry configurationtranslation
Specify timeout after which the checking for activity is donesampling-timeout
Timeout in seconds (max: 2days, recommended 900s)timeout
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2147
I Commandsip nat translation sampling-timeout
Page 2292
ip next-hop-self eigrp[no] { ip | ipv6 } next-hop-self eigrp <eigrp-ptag>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Configures IP-EIGRP next-hop-selfnext-hop-self
EIGRP interface configuration commandseigrp
Process tageigrp-ptag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2148
I Commandsip next-hop-self eigrp
Page 2293
ip offset-list eigrp[no] { ip | ipv6 } offset-list eigrp <eigrp-ptag> { { route-map <map> } | { prefix-list <list> } } { in | out }<offset>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Add or subtract offset from EIGRP metricsoffset-list
EIGRP interface configuration commandseigrp
Process tageigrp-ptag
Use a route-map for offset-list selectionroute-map
Route-map namemap
Use a prefix-list for offset-list selectionprefix-list
Reference to prefix-list namelist
Perform offset on incoming updatesin
Perform offset on outgoing updatesout
Offsetoffset
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2149
I Commandsip offset-list eigrp
Page 2294
ip ospf advertise-subnet[no] ip ospf advertise-subnet
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Advertise loopback interface IP subnet in router LSAadvertise-subnet
Command Mode
• /exec/configure/if-loopback
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2150
I Commandsip ospf advertise-subnet
Page 2295
ip ospf authentication-key{ { ip ospf authentication-key <key> } | { no ip ospf authentication-key [ <key> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Configure the authentication key for the interfaceauthentication-key
Authentication keykey
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2151
I Commandsip ospf authentication-key
Page 2296
ip ospf authentication[no] ip ospf authentication [ message-digest | null ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Authentication on the interfaceauthentication
(Optional) Use message-digest authenticationmessage-digest
(Optional) Use null(disable) authenticationnull
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2152
I Commandsip ospf authentication
Page 2297
ip ospf authentication key-chain{ ip ospf authentication key-chain <keychain> } | { no ip ospf authentication key-chain [ <keychain> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Authentication on the interfaceauthentication
Authentication password key-chainkey-chain
Key-chain namekeychain
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2153
I Commandsip ospf authentication key-chain
Page 2298
ip ospf bfd[no] ip ospf bfd [ disable ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Enable BFD on this interfacebfd
(Optional) Disable BFD on this interfacedisable
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2154
I Commandsip ospf bfd
Page 2299
ip ospf cost{ ip ospf cost <cost> } | { no ip ospf cost [ <cost> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Cost associated with interfacecost
Cost valuecost
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2155
I Commandsip ospf cost
Page 2300
ip ospf dead-interval{ ip ospf dead-interval <interval> } | { no ip ospf dead-interval [ <interval> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Dead intervaldead-interval
(seconds)interval
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2156
I Commandsip ospf dead-interval
Page 2301
ZZZ_4621[ ip ospf event-history { adjacency | event | ha | flooding | lsa | spf | redistribution | ldp | te | rib | hello | spf-trigger| objstore } size { <size_in_text> | <size_in_Kbytes> } ] | [ no ip ospf event-history { adjacency | event | ha |flooding | lsa | spf | redistribution | ldp | te | rib | hello | spf-trigger | objstore } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) IP eventsip
(Optional) Debug OSPF eventsospf
(Optional) log debug events into event history bufferevent-history
(Optional) Adjacency formation logsadjacency
(Optional) Internal event logsevent
(Optional) HA and GR logsha
(Optional) LSA flooding logsflooding
(Optional) LSA generation and databse logslsa
(Optional) SPF calculation logsspf
(Optional) Redistribution logsredistribution
(Optional) LDP related logsldp
(Optional) MPLS TE related logste
(Optional) RIB related logsrib
(Optional) HELLO related logshello
(Optional) SPF TRIGGER related logsspf-trigger
(Optional) DME OBJSTORE related logsobjstore
(Optional) Configure the size of the event-hist buffersize
(Optional) Buffer sizesize_in_text
(Optional) Size of the file in kbytessize_in_Kbytes
Command Mode
• /exec/configure/router-ospf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2157
I CommandsZZZ_4621
Page 2302
ip ospf event-history cli[ no ip ospf event-history cli ] | [ ip ospf event-history cli size { <size_in_text> | <size_in_Kbytes> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) IP eventsip
(Optional) Debug OSPF eventsospf
(Optional) log debug events into event history bufferevent-history
(Optional) Cli logscli
(Optional) Configure the size of the event-hist buffersize
(Optional) Buffer sizesize_in_text
(Optional) Size of the file in kbytessize_in_Kbytes
Command Mode
• /exec/configure/router-ospf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2158
I Commandsip ospf event-history cli
Page 2303
ip ospf event-history detail[ no ip ospf event-history detail ] | [ ip ospf event-history detail size { <size_in_text> | <size_in_Kbytes> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) IP eventsip
(Optional) Debug OSPF eventsospf
(Optional) log debug events into event history bufferevent-history
(Optional) Detailed event history bufferdetail
(Optional) Configure the size of the verbose event-hist buffersize
(Optional) Buffer sizesize_in_text
(Optional) Size of the file in kbytessize_in_Kbytes
Command Mode
• /exec/configure/router-ospf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2159
I Commandsip ospf event-history detail
Page 2304
ip ospf hello-interval{ ip ospf hello-interval <interval> } | { no ip ospf hello-interval [ <interval> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Hello intervalhello-interval
(seconds)interval
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2160
I Commandsip ospf hello-interval
Page 2305
ip ospf message-digest-key md5{ { ip ospf message-digest-key <keyid> md5 <key> } | { no ip ospf message-digest-key <keyid> [ md5 <key>] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Message digest authentication password (key)message-digest-key
Key IDkeyid
Use MD5 algorithmmd5
The OSPF password (key)key
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2161
I Commandsip ospf message-digest-key md5
Page 2306
ip ospf mtu-ignore[no] ip ospf mtu-ignore
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Disable OSPF MTU mismatch detectionmtu-ignore
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2162
I Commandsip ospf mtu-ignore
Page 2307
ip ospf network broadcast{ ip ospf network { broadcast | point-to-point } } | { no ip ospf network [ { broadcast | point-to-point } ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Network typenetwork
Specify OSPF broadcast multi-access networkbroadcast
Specify OSPF point-to-point networkpoint-to-point
Command Mode
• /exec/configure/if-broadcast /exec/configure/if-p2p /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2163
I Commandsip ospf network broadcast
Page 2308
ip ospf network point-to-point{ ip ospf network point-to-point } | { no ip ospf network [ point-to-point ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Network typenetwork
Specify OSPF point-to-point networkpoint-to-point
Command Mode
• /exec/configure/if-loopback
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2164
I Commandsip ospf network point-to-point
Page 2309
ip ospf passive-interface[ default | no ] ip ospf passive-interface
Syntax Description
(Optional) Undo a commanddefault
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Suppress routing updates on the interfacepassive-interface
Command Mode
• /exec/configure/if-broadcast /exec/configure/if-p2p /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2165
I Commandsip ospf passive-interface
Page 2310
ip ospf prefix-attributes n-flag-clear[no] ip ospf prefix-attributes n-flag-clear
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Prefix attributesprefix-attributes
Clear N-Flag for the interface prefixesn-flag-clear
Command Mode
• /exec/configure/if-loopback
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2166
I Commandsip ospf prefix-attributes n-flag-clear
Page 2311
ip ospf priority{ ip ospf priority <prio> } | { no ip ospf priority [ <prio> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Router prioritypriority
Router priorityprio
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2167
I Commandsip ospf priority
Page 2312
ip ospf retransmit-interval{ ip ospf retransmit-interval <interval> } | { no ip ospf retransmit-interval [ <interval> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Packet retransmission intervalretransmit-interval
(seconds)interval
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2168
I Commandsip ospf retransmit-interval
Page 2313
ip ospf shutdown[no] ip ospf shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
shutdown ospf on this interfaceshutdown
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2169
I Commandsip ospf shutdown
Page 2314
ip ospf transmit-delay{ ip ospf transmit-delay <delay> } | { no ip ospf transmit-delay [ <delay> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
OSPF configuration commandsospf
Packet transmission delaytransmit-delay
(seconds)delay
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2170
I Commandsip ospf transmit-delay
Page 2315
ip passive-interface eigrp[ default | no ] { ip | ipv6 } passive-interface eigrp <eigrp-ptag>
Syntax Description
(Optional) Undo a commanddefault
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Suppress routing updates on an interfacepassive-interface
EIGRP interface configuration commandseigrp
Process tageigrp-ptag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2171
I Commandsip passive-interface eigrp
Page 2316
ip pim anycast-rp[no] ip pim anycast-rp <anycast-rp> <rp-addr>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure an RP in an Anycast-RP set (using PIM)anycast-rp
Address for the Anycast-RP addressanycast-rp
Address of RP in the Anycast-RP setrp-addr
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2172
I Commandsip pim anycast-rp
Page 2317
ip pim assert-rate-limit{ { ip pim assert-rate-limit <rate> } | { no ip pim assert-rate-limit [ <rate> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Rate limit for PIM Assertsassert-rate-limit
Packets per secondrate
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2173
I Commandsip pim assert-rate-limit
Page 2318
ip pim auto-enable{ { no ip pim auto-enable } | { ip pim auto-enable } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Auto-enable configure on the vrfauto-enable
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2174
I Commandsip pim auto-enable
Page 2319
ip pim auto-rp listen{ ip pim auto-rp { listen | forward } + } | { no ip pim auto-rp [ { listen | forward } + ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Auto-RP protocol RP-distribution configurationauto-rp
Listen to Auto-RP messageslisten
Forward Auto-RP messagesforward
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2175
I Commandsip pim auto-rp listen
Page 2320
ip pim auto-rp mapping-agent-policy{ ip pim auto-rp mapping-agent-policy { <route-map-name> | <rtr_pol_name> } | no ip pim auto-rpmapping-agent-policy [ <route-map-name> | <rtr_pol_name> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Auto-RP protocol RP-distribution configurationauto-rp
Specify policy for filtering Mapping Agent messagesmapping-agent-policy
Route-map nameroute-map-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2176
I Commandsip pim auto-rp mapping-agent-policy
Page 2321
ip pim auto-rp mapping-agent send-rp-discovery{ { ip pim { { auto-rp mapping-agent } | send-rp-discovery } <interface> [ scope <ttl> ] } | { no ip pim { {auto-rp mapping-agent } | send-rp-discovery } [ <interface> ] [ scope <ttl> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Auto-RP protocol RP-distribution configurationauto-rp
Configures router to send Auto-RP Discovery messagessend-rp-discovery
Configures router as an Auto-RP RP-mapping agentmapping-agent
Use IP address of interface for Auto-RP Announce messagesinterface
(Optional) Configure the scope of Auto-RP Discovery messagesscope
(Optional) TTL value for scopettl
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2177
I Commandsip pim auto-rp mapping-agent send-rp-discovery
Page 2322
ip pim auto-rp rp-candidate-policy{ ip pim auto-rp rp-candidate-policy { <route-map-name> | <rtr_pol_name> } | no ip pim auto-rprp-candidate-policy [ <route-map-name> | <rtr_pol_name> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Auto-RP protocol RP-distribution configurationauto-rp
Specify policy for filtering RP candidate messagesrp-candidate-policy
Route-map nameroute-map-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2178
I Commandsip pim auto-rp rp-candidate-policy
Page 2323
ip pim auto-rp rp-candidate send-rp-announce group-listroute-map prefix-list
{ { ip pim { auto-rp rp-candidate | send-rp-announce } { <interface> | <ipaddr> } { group-list <prefix> |route-map <route-map-name> | prefix-list <prefix-list-name> } { [ scope <ttl> ] | [ interval <interval> ] | [bidir ] } + } | { no ip pim { { auto-rp rp-candidate } | send-rp-announce } [ <interface> | <ipaddr> ] [ group-list<prefix> | route-map <route-map-name> | prefix-list <prefix-list-name> ] { [ scope <ttl> ] | [ interval <interval>] | [ bidir ] } } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Auto-RP protocol RP-distribution configurationauto-rp
Configures router to send Auto-RP Announce messagessend-rp-announce
Configures router to be an Auto-RP candidate RPrp-candidate
Use IP address of interface for Auto-RP Announce messagesinterface
IP address of RP for groupipaddr
Group range listgroup-list
Prefix of group rangeprefix
Group range policy for Auto-RP Candidate RProute-map
Route-map nameroute-map-name
Prefix List policy for Auto-RP Candidate RPprefix-list
Name of prefix-listprefix-list-name
(Optional) Configure the scope of Auto-RP Announce messagesscope
(Optional) TTL value for scopettl
(Optional) Auto-RP Announce message transmission intervalinterval
(Optional) Interval in secondsinterval
(Optional) Group range advertised in PIM bidirectional modebidir
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2179
I Commandsip pim auto-rp rp-candidate send-rp-announce group-list route-map prefix-list
Page 2324
ip pim bfd-instance[no] ip pim bfd-instance [ disable ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM interface configuration commandspim
Configures BFD on interfacebfd-instance
(Optional) Disable BFD on interfacedisable
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2180
I Commandsip pim bfd-instance
Page 2325
ip pim bfd[no] ip pim bfd
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Enable / Disable BFD for all PIM interfaces in the VRFbfd
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2181
I Commandsip pim bfd
Page 2326
ip pim bidir-rp-limit[no] ip pim bidir-rp-limit <limit>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configures maximum Bidir RPs for IPv4 PIM in this VRFbidir-rp-limit
Set limit for Bidir RPs permitted in IPv4 PIMlimit
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2182
I Commandsip pim bidir-rp-limit
Page 2327
ip pim border-router[no] ip pim border-router
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM interface configuration commandspim
Configures the interface to be a boundary of a PIM-SM domainborder-router
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2183
I Commandsip pim border-router
Page 2328
ip pim border[no] ip pim border
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM interface configuration commandspim
Configures interface to be a boundary of a PIM domainborder
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2184
I Commandsip pim border
Page 2329
ip pim bsr-candidate{ { ip pim [ bsr ] bsr-candidate <interface> [ hash-len <hash-len> ] [ priority <priority> ] [ interval <interval>] } | { no ip pim [ bsr ] bsr-candidate [ <interface> ] [ hash-len <hash-len> ] [ priority <priority> ] [ interval<interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
(Optional) Bootstrap protocol RP-distribution configurationbsr
Configure router as a Bootstrap Router candidatebsr-candidate
Use IP address of interface for Bootstrap messagesinterface
(Optional) Hash mask length used in Bootstrap messageshash-len
(Optional) Hash mask length valuehash-len
(Optional) BSR priority used in Bootstrap messagespriority
(Optional) BSR priority valuepriority
(Optional) Bootstrap message transmission intervalinterval
(Optional) Interval in secondsinterval
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2185
I Commandsip pim bsr-candidate
Page 2330
ip pim bsr bsr-policy{ ip pim bsr bsr-policy { <route-map-name> | <rtr_pol_name> } | no ip pim bsr bsr-policy [ <route-map-name>| <rtr_pol_name> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Bootstrap protocol RP-distribution configurationbsr
Specify policy for filtering BSR messagesbsr-policy
Route-map nameroute-map-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2186
I Commandsip pim bsr bsr-policy
Page 2331
ip pim bsr listen{ ip pim bsr { listen | forward } + } | { no ip pim bsr [ { listen | forward } + ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Bootstrap protocol RP-distribution configurationbsr
Listen to Bootstrap/Candidate-RP messageslisten
Forward Bootstrap/Candidate-RP messagesforward
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2187
I Commandsip pim bsr listen
Page 2332
ip pim bsr rp-candidate-policy{ ip pim bsr rp-candidate-policy { <route-map-name> | <rtr_pol_name> } | no ip pim bsr rp-candidate-policy[ <route-map-name> | <rtr_pol_name> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Bootstrap protocol RP-distribution configurationbsr
Specify policy for filtering RP candidate messagesrp-candidate-policy
Route-map nameroute-map-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2188
I Commandsip pim bsr rp-candidate-policy
Page 2333
ip pim dr-delay{ { ip pim dr-delay <delay> } | { no ip pim dr-delay [ <delay> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM interface configuration commandspim
Configures delay for PIM DR election on interfacedr-delay
Delay valuedelay
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2189
I Commandsip pim dr-delay
Page 2334
ip pim dr-priority{ { ip pim dr-priority <priority> } | { no ip pim dr-priority [ <priority> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM interface configuration commandspim
Configures priority for PIM DR election on interfacedr-priority
Priority valuepriority
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2190
I Commandsip pim dr-priority
Page 2335
ip pim event-history assert[no] ip pim event-history assert { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure event-history bufferevent-history
Assert events for PIMassert
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2191
I Commandsip pim event-history assert
Page 2336
ip pim event-history bidir[no] ip pim event-history bidir { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure event-history bufferevent-history
Bidir events for PIMbidir
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2192
I Commandsip pim event-history bidir
Page 2337
ip pim event-history cli[no] ip pim event-history cli { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure event-history bufferevent-history
CLI events for PIMcli
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2193
I Commandsip pim event-history cli
Page 2338
ip pim event-history data-register-receive[no] ip pim event-history data-register-receive { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure event-history bufferevent-history
Data register recv events for PIMdata-register-receive
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2194
I Commandsip pim event-history data-register-receive
Page 2339
ip pim event-history hello[no] ip pim event-history hello { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure event-history bufferevent-history
Hello events for PIMhello
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2195
I Commandsip pim event-history hello
Page 2340
ip pim event-history join-prune-summary[no] ip pim event-history join-prune-summary { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure event-history bufferevent-history
JoinPrune-Summary for PIMjoin-prune-summary
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2196
I Commandsip pim event-history join-prune-summary
Page 2341
ip pim event-history join-prune-tw[no] ip pim event-history join-prune-tw { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure event-history bufferevent-history
JoinPrune-tw for PIMjoin-prune-tw
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2197
I Commandsip pim event-history join-prune-tw
Page 2342
ip pim event-history join-prune[no] ip pim event-history join-prune { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure event-history bufferevent-history
Join Prune events for PIMjoin-prune
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2198
I Commandsip pim event-history join-prune
Page 2343
ip pim event-history mrib[no] ip pim event-history mrib { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure PIM event historypim
Configure event-history bufferevent-history
MRIB events for PIMmrib
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2199
I Commandsip pim event-history mrib
Page 2344
ip pim event-history mvpn[no] ip pim event-history mvpn { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure PIM event historypim
Configure event-history bufferevent-history
MVPN events for PIMmvpn
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2200
I Commandsip pim event-history mvpn
Page 2345
ip pim event-history nbm[no] ip pim event-history nbm { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure PIM event historypim
Configure event-history bufferevent-history
NBM events for PIMnbm
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2201
I Commandsip pim event-history nbm
Page 2346
ip pim event-history null-register[no] ip pim event-history null-register { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure event-history bufferevent-history
Null register events for PIMnull-register
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2202
I Commandsip pim event-history null-register
Page 2347
ip pim event-history packet[no] ip pim event-history packet { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure event-history bufferevent-history
Packet events for PIMpacket
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2203
I Commandsip pim event-history packet
Page 2348
ip pim event-history pim-library[no] ip pim event-history pim-library { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure PIM event historypim
Configure event-history bufferevent-history
PIM library eventspim-library
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2204
I Commandsip pim event-history pim-library
Page 2349
ip pim event-history rp[no] ip pim event-history rp { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure event-history bufferevent-history
RP events for PIMrp
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2205
I Commandsip pim event-history rp
Page 2350
ip pim event-history txlist[no] ip pim event-history txlist { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure PIM event historypim
Configure event-history bufferevent-history
Txlist events for PIMtxlist
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2206
I Commandsip pim event-history txlist
Page 2351
ip pim event-history vpc[no] ip pim event-history vpc { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure PIM event historypim
Configure event-history bufferevent-history
vPC events for PIMvpc
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2207
I Commandsip pim event-history vpc
Page 2352
ip pim event-history vrf[no] ip pim event-history vrf { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure event-history bufferevent-history
VRF events for PIMvrf
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2208
I Commandsip pim event-history vrf
Page 2353
ip pim evpn-border-leaf[no] ip pim evpn-border-leaf
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure this node as a border leafevpn-border-leaf
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2209
I Commandsip pim evpn-border-leaf
Page 2354
ip pim extranet[no] ip pim extranet
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Support for Extranet RPF lookupextranet
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2210
I Commandsip pim extranet
Page 2355
ip pim file-debug[no] ip pim file-debug
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Collect all debugs to a filefile-debug
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2211
I Commandsip pim file-debug
Page 2356
ip pim flush-routes[no] ip pim flush-routes
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Remove routes when restarting PIMflush-routes
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2212
I Commandsip pim flush-routes
Page 2357
ip pim group-list[no] ip pim { use-shared-tree-only | spt-threshold infinity } group-list { <route-map-name> | prefix-list<prefix-list-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Use (*,G) only state, no source state is createduse-shared-tree-only
Source-tree switching thresholdspt-threshold
Never switch to source-treeinfinity
Specify group ranges through policygroup-list
Route-map nameroute-map-name
Prefix List policyprefix-list
Name of prefix-listprefix-list-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2213
I Commandsip pim group-list
Page 2358
ip pim hello-authentication ah-md5{ ip pim hello-authentication ah-md5 <auth-key> | no ip pim hello-authentication ah-md5 [ <auth-key> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM interface configuration commandspim
Add AH header option to Helloshello-authentication
Use MD5 HMACah-md5
MD5 authentication keyauth-key
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2214
I Commandsip pim hello-authentication ah-md5
Page 2359
ip pim hello-interval{ { ip pim hello-interval <interval> } | { no ip pim hello-interval [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM interface configuration commandspim
Configures the Hello interval for interfacehello-interval
Interval in millisecondsinterval
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2215
I Commandsip pim hello-interval
Page 2360
ip pim isolate[no] ip pim isolate
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Isolate this router from PIM perspectiveisolate
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2216
I Commandsip pim isolate
Page 2361
ip pim jp-interval[no] ip pim jp-interval <interval>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM interface configuration commandspim
Join-Prune interval used between peersjp-interval
Interval in secondsinterval
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2217
I Commandsip pim jp-interval
Page 2362
ip pim jp-policy{ ip pim jp-policy { <route-map-name> | prefix-list <prefix-list-name> } [ in | out ] | no ip pim jp-policy {<route-map-name> | prefix-list <prefix-list-name> } [ in | out ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM interface configuration commandspim
Specify policy for receiving Join-Prune messagesjp-policy
Route-map nameroute-map-name
Prefix List policy for static RPprefix-list
Name of prefix-listprefix-list-name
(Optional) Inboundin
(Optional) Outboundout
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2218
I Commandsip pim jp-policy
Page 2363
ip pim log-neighbor-changes[no] ip pim log-neighbor-changes
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Log up/down PIM neighbor transitionslog-neighbor-changes
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2219
I Commandsip pim log-neighbor-changes
Page 2364
ip pim neighbor-policy prefix-list{ { ip pim neighbor-policy { <route-map-name> | prefix-list <prefix-list-name> } } | { no ip pim neighbor-policy[ <route-map-name> | prefix-list <prefix-list-name> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM interface configuration commandspim
Configures a neighbor policy for filtering adjacenciesneighbor-policy
Route-map nameroute-map-name
Prefix List policy for neighborprefix-list
Name of prefix-listprefix-list-name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2220
I Commandsip pim neighbor-policy prefix-list
Page 2365
ip pim passive{ ip pim passive | no ip pim passive }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM interface configuration commandspim
Interface in passive mode. No send/recvpassive
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2221
I Commandsip pim passive
Page 2366
ip pim pre-build-spt{ { { ip pim pre-build-spt [ force ] } [ route-map <route-map-name> | prefix-list <prefix-list-name> ] } | { noip pim pre-build-spt } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Pre construct PIM trees for all known (S,G)spre-build-spt
(Optional) Enable pre-build-spt irrespective of (*,G) stateforce
(Optional) Route Map policy for pre-build-sptroute-map
(Optional) Route-map nameroute-map-name
(Optional) Prefix List policy for pre-build-sptprefix-list
(Optional) Name of prefix-listprefix-list-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2222
I Commandsip pim pre-build-spt
Page 2367
ip pim register-policy{ ip pim register-policy { <route-map-name> | prefix-list <prefix-list-name> } | no ip pim register-policy [<route-map-name> | prefix-list <prefix-list-name> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Specify policy for receiving Register messagesregister-policy
Route-map nameroute-map-name
Prefix List policy for Registersprefix-list
Name of prefix-listprefix-list-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2223
I Commandsip pim register-policy
Page 2368
ip pim register-rate-limit{ { ip pim register-rate-limit <rate> } | { no ip pim register-rate-limit [ <rate> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Rate limit for PIM data registersregister-rate-limit
Packets per secondrate
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2224
I Commandsip pim register-rate-limit
Page 2369
ip pim register-source{ { ip pim register-source { <src-interface> } } | { no ip pim register-source [ <src-interface> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure source address for Register messagesregister-source
Use IP address of this interface for Register messagessrc-interface
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2225
I Commandsip pim register-source
Page 2370
ip pim register-until-stop[no] ip pim register-until-stop
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Send Data Registers till Register Stop is receivedregister-until-stop
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2226
I Commandsip pim register-until-stop
Page 2371
ip pim rp-address{ { ip pim rp-address <rp-address> [ group-list <prefix> | route-map <route-map-name> | prefix-list<prefix-list-name> ] [ bidir ] [ override ] } | { no ip pim rp-address <rp-address> [ group-list <prefix> |route-map <route-map-name> | prefix-list <prefix-list-name> ] [ bidir ] [ override ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configure static RP for group rangerp-address
IP address of router which is RP for group rangerp-address
(Optional) Group range for static RPgroup-list
(Optional) Group range prefixprefix
(Optional) Route Map policy for static RProute-map
(Optional) Route-map nameroute-map-name
(Optional) Prefix List policy for static RPprefix-list
(Optional) Name of prefix-listprefix-list-name
(Optional) Group range is treated in PIM bidirectional modebidir
(Optional) RP address will override the dynamically learnt RPsoverride
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2227
I Commandsip pim rp-address
Page 2372
ip pim rp-candidate group-list route-map prefix-list{ { ip pim [ bsr ] rp-candidate <interface> { group-list <prefix> | route-map <route-map-name> | prefix-list<prefix-list-name> } [ priority <priority> ] [ interval <interval> ] [ bidir ] } | { no ip pim [ bsr ] rp-candidate[ <interface> ] [ group-list <prefix> ] [ route-map <route-map-name> ] [ prefix-list <prefix-list-name> ] [priority <priority> ] [ interval <interval> ] [ bidir ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
(Optional) Bootstrap protocol RP-distribution configurationbsr
Configure router as a Rendezvous Point (RP) candidaterp-candidate
Use IP address of interface for Candidate-RP messagesinterface
Group range listgroup-list
Prefix of group rangeprefix
Group range policy for Candidate RProute-map
Route-map nameroute-map-name
Prefix List policy for Candidate RPprefix-list
Name of prefix-listprefix-list-name
(Optional) RP priority used in Candidate-RP messagespriority
(Optional) RP priority valuepriority
(Optional) Bootstrap message transmission intervalinterval
(Optional) Interval in secondsinterval
(Optional) Group range advertised in PIM bidirectional modebidir
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2228
I Commandsip pim rp-candidate group-list route-map prefix-list
Page 2373
ip pim sg-expiry-timer infinity{ { ip pim [ sparse ] sg-expiry-timer { <expiry-time> | infinity } [ sg-list <route-map-name> | prefix-list<prefix-list-name> ] } | { no ip pim [ sparse ] sg-expiry-timer { <expiry-time> | infinity } [ sg-list<route-map-name> | prefix-list <prefix-list-name> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
(Optional) PIM ASMsparse
Adjust expiry time for PIM ASM (S,G) routessg-expiry-timer
Expiry timer interval in secondsexpiry-time
Never expire (S,G) route due to data inactivityinfinity
(Optional) Specifies route-map for (S,G)s to apply the expiry timersg-list
(Optional) Route-map nameroute-map-name
(Optional) Specifies prefix-list for (S,G)s to apply the expiry timerprefix-list
(Optional) Name of prefix-listprefix-list-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2229
I Commandsip pim sg-expiry-timer infinity
Page 2374
ip pim sparse-modeip pim sparse-mode | no ip pim [ sparse-mode ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM interface configuration commandspim
Configures sparse-mode PIM on interfacesparse-mode
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2230
I Commandsip pim sparse-mode
Page 2375
ip pim ssm{ ip pim ssm { { range { <group> + | none } } | { route-map <route-map-name> } | { prefix-list<prefix-list-name> } } | no ip pim ssm { { range { <group> + | none } } | { route-map <route-map-name> }| { prefix-list <prefix-list-name> } } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Source Specific Multicast (SSM) groupsssm
Configure explicit group rangesrange
List of group range prefixesgroup
Group range route-map policy for SSM rangeroute-map
Route-map nameroute-map-name
Group range prefix-list policy for SSM rangeprefix-list
Name of prefix-listprefix-list-name
Remove all SSM group rangesnone
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2231
I Commandsip pim ssm
Page 2376
ip pim state-limit{ { ip pim state-limit <max-states> [ reserved <route-map-name> <max-reserved> ] } | { no ip pim state-limit[ <max-states> [ reserved <route-map-name> <max-reserved> ] ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Configures State limitstate-limit
Maximum (*,G)/(S,G) entries allowed in this VRFmax-states
(Optional) Configures Reserved limitreserved
(Optional) Route-map nameroute-map-name
(Optional) Maximum reserved (*,G)/(S,G) entries allowed in this VRFmax-reserved
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2232
I Commandsip pim state-limit
Page 2377
ip pim strict-rfc-compliant{ { ip pim strict-rfc-compliant } | { no ip pim strict-rfc-compliant } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM interface configuration commandspim
Dont process joins from unknown neighbors on this interfacestrict-rfc-compliant
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2233
I Commandsip pim strict-rfc-compliant
Page 2378
ip pim strict-rfc-compliant{ { ip pim strict-rfc-compliant } | { no ip pim strict-rfc-compliant } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
PIM global configuration commandspim
Don't process joins from unknown neighborsstrict-rfc-compliant
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2234
I Commandsip pim strict-rfc-compliant
Page 2379
ip ping source-interface[no] ip ping source-interface <ifnum> [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure ping clientping
Configure source interface feature for ping clientsource-interface
Source interfaceifnum
(Optional) Configure VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2235
I Commandsip ping source-interface
Page 2380
ip policy match router-address[no] ip policy match router-address
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure PBR featurepolicy
Match valuesmatch
Router's IP addressrouter-address
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2236
I Commandsip policy match router-address
Page 2381
ip policy route-mapip policy route-map <route-map-name> | no ip policy route-map [ <route-map-name> | <route-map-name> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure PBR featurepolicy
Route-map for PBRroute-map
Route-map nameroute-map-name
(Optional) Route-map nameroute-map-name
(Optional) Known route-map nameroute-map-name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2237
I Commandsip policy route-map
Page 2382
ip port-unreachable[no] ip port-unreachable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Enable sending ICMP port-unreachableport-unreachable
Command Mode
• /exec/configure/if-igp /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2238
I Commandsip port-unreachable
Page 2383
ip port access-group[no] ip port access-group <name> <inout>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Port policyport
Specify access control for packetsaccess-group
List namename
Traffic directioninout
Command Mode
• /exec/configure/system/acl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2239
I Commandsip port access-group
Page 2384
ip port access-group[no] ip port access-group <name> <inout>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Port policyport
Specify access control for packetsaccess-group
List namename
Traffic directioninout
Command Mode
• /exec/configure/if-set-acl-l2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2240
I Commandsip port access-group
Page 2385
ip prefix-list description{ ip prefix-list <ipv4-pfl-name> description <line> } | { no ip prefix-list <ipv4-pfl-name> description }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Build a prefix listprefix-list
Name of prefix-listipv4-pfl-name
Known prefix-list nameipv4-pfl-name
Description of the IP prefix listdescription
IP prefix-list description stringline
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2241
I Commandsip prefix-list description
Page 2386
ip prefix-list permit{ ip prefix-list <ipv4-pfl-name> [ seq <seq> ] { permit | deny } <prefix> { [ eq <equal> ] | [ ge <greater> ] [le <lesser> ] } [ mask <mask> ] } | { no ip prefix-list { <ipv4-pfl-name> | <ipv4-pfl-name> } [ seq <seq> ] [{ permit | deny } <prefix> { [ eq <equal> ] | [ ge <greater> ] [ le <lesser> ] } [ mask <mask> ] ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Build a prefix listprefix-list
Name of prefix-listipv4-pfl-name
Name of prefix-listipv4-pfl-name
Known prefix-list nameipv4-pfl-name
(Optional) Sequence number of an entryseq
(Optional) Sequence numberseq
Specify routes to forwardpermit
Specify routes to rejectdeny
IP prefix network/length, e.g., 35.0.0.0/8prefix
(Optional) Exact prefix length to be matchedeq
(Optional) Exact prefix lengthequal
(Optional) Minimum prefix length to be matchedge
(Optional) Minimum prefix lengthgreater
(Optional) Maximum prefix length to be matchedle
(Optional) Maximum prefix lengthlesser
(Optional) Explicit match maskmask
(Optional) Mask to use with the prefixmask
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2242
I Commandsip prefix-list permit
Page 2387
ip proxy-arp{ ip proxy-arp | no ip proxy-arp }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure proxy ARPproxy-arp
Command Mode
• /exec/configure/if-igp /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2243
I Commandsip proxy-arp
Page 2388
ip radius source-interface[no] ip radius source-interface | ip radius source-interface <interface>
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Radius serverradius
Source interface to be used to reach radius serversource-interface
Interface Descriptioninterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2244
I Commandsip radius source-interface
Page 2389
ip redirectsip redirects | no ip redirects
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Send ICMP Redirect messagesredirects
Command Mode
• /exec/configure/if-igp /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2245
I Commandsip redirects
Page 2390
ip rip authentication key-chain{ ip rip authentication key-chain <keychain> | no ip rip authentication key-chain [ <keychain> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
RIP configuration commandsrip
Authentication controlauthentication
Set authentication key-chainkey-chain
Name of key-chainkeychain
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2246
I Commandsip rip authentication key-chain
Page 2391
ip rip authentication mode text{ ip rip authentication mode { text | md5 } | no ip rip authentication mode [ { text | md5 } ] }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
RIP configuration commandsrip
RIP authentication controlauthentication
Set authentication modemode
Clear text authenticationtext
Keyed message digestmd5
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2247
I Commandsip rip authentication mode text
Page 2392
ip rip metric{ ipv6 | ip } rip { metric-offset | offset-list } <metric> | no { ipv6 | ip } rip { metric-offset | offset-list } [<metric> ]
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure IP featuresip
RIP configuration commandsrip
RIP metric for interfacemetric-offset
RIP metric for interfaceoffset-list
RIP metric valuemetric
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2248
I Commandsip rip metric
Page 2393
ip rip passive-interface[no] { ipv6 | ip } rip passive-interface
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure IP featuresip
RIP configuration commandsrip
RIP passive interfacepassive-interface
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2249
I Commandsip rip passive-interface
Page 2394
ip rip poison-reverse[no] { ipv6 | ip } rip poison-reverse
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure IP featuresip
RIP configuration commandsrip
RIP poison reverse (default split-horizon)poison-reverse
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2250
I Commandsip rip poison-reverse
Page 2395
ip rip route-filter route in[no] { ipv6 | ip } rip route-filter { route-map <map> | prefix-list <list> } { in | out }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure IP featuresip
RIP configuration commandsrip
RIP route filteringroute-filter
route-map policy to constrain route filteringroute-map
prefix-list policy to constrain route filteringprefix-list
Route-map namemap
prefix-list namelist
inboundin
outboundout
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2251
I Commandsip rip route-filter route in
Page 2396
ip rip summary-address[no] ip rip summary-address <ip-prefix> | no ipv6 rip summary-address <ipv6-prefix> | ipv6 ripsummary-address <ipv6-prefix>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
RIP configuration commandsrip
RIP summarization addresssummary-address
Exact prefixip-prefix
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2252
I Commandsip rip summary-address
Page 2397
ip route[no] ip route { <ip-addr> <ip-mask> | <ip-prefix> } { <interface> | { { <pin-interface> <next-hop> } | {<next-hop> | <nh-prefix> } | { <vlan-interface> } } [ vrf { <vrf-name> | <vrf-known-name> } ] } [ track<object-num> ] [ name <rt-name> ] [ tag <tag-value> | <pref> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Route informationroute
IP prefix in format i.i.i.iip-addr
IP network mask in format m.m.m.mip-mask
IP prefix and network mask length in format x.x.x.x/mip-prefix
Pin interfacepin-interface
IP next-hop address in format i.i.i.inext-hop
IP next-hop prefix in format i.i.i.i/mnh-prefix
Interface for interface static routesinterface
vlan interfacevlan-interface
(Optional) Specify the Object to be Trackedtrack
(Optional) Track Object Numberobject-num
(Optional) Specify name of the next hopname
(Optional) Name of next hoprt-name
(Optional) Route preferencepref
(Optional) Supply tag value with static routetag
(Optional) 32-bit value for tagtag-value
(Optional) VRF for next-hop if different from this vrfvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure /exec/configure/config-mgmt /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2253
I Commandsip route
Page 2398
ip route static bfd[no] ip route static bfd <pin-interface> <next-hop>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Route informationroute
Static route based configurationstatic
Enable bfd detection on static routebfd
Interface on which bfd has to be enabledpin-interface
IP next-hop address in format i.i.i.inext-hop
Command Mode
• /exec/configure /exec/configure/config-mgmt /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2254
I Commandsip route static bfd
Page 2399
ip router eigrp[no] { ip | ipv6 } router eigrp <eigrp-ptag>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Enable a routing processrouter
Configure an EIGRP routing process on interfaceeigrp
Process tageigrp-ptag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2255
I Commandsip router eigrp
Page 2400
ip router isis[no] ip router isis <tag>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Enable a routing processrouter
Intermediate System to Intermediate System (IS-IS)isis
Process tagtag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2256
I Commandsip router isis
Page 2401
ip router ospf area[no] ip router ospf <tag> area { <area-id-ip> | <area-id-int> } [ secondaries none ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Enable a routing processrouter
OSPF configuration commandsospf
Process tagtag
Area associated with interfacearea
OSPF area ID in IP address formatarea-id-ip
OSPF area ID as a decimal formatarea-id-int
(Optional) Do not include secondary IP addressessecondaries
(Optional) Do not include secondary IP addressesnone
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2257
I Commandsip router ospf area
Page 2402
ip router ospf multi-area[no] ip router ospf [ <tag> ] multi-area <area-id-ip>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Enable a routing processrouter
OSPF configuration commandsospf
(Optional) Process tagtag
Multi area associated with interfacemulti-area
Area Id as an integer or ip addressarea-id-ip
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2258
I Commandsip router ospf multi-area
Page 2403
ip router rip[no] { ipv6 | ip } router rip <tag>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Enable a routing processrouter
Routing Information Protocol (RIP)rip
Process tagtag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2259
I Commandsip router rip
Page 2404
ip routing download-on-convergence[no] ip routing download-on-convergence
Syntax Description
(Optional) Negate a command or set its defaultsno
IP eventsip
Enable debugging for routing eventsrouting
Download Routes/RNHs after Table Convergencedownload-on-convergence
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2260
I Commandsip routing download-on-convergence
Page 2405
ip routing event-history[no] ip routing event-history { add-route | cli | delete-route | detail | errors | general | ha | loop-detection |modify-route | notifications | recursive-next-hop | summary | ufdm | ufdm-detail | ufdm-summary } size {<size_in_text> | <size_in_bytes> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Routing informationrouting
Configure routing event logevent-history
Add routeadd-route
CLIcli
Delete routedelete-route
Detaildetail
Errorserrors
Generalgeneral
HAha
Loop detectionloop-detection
Modify routemodify-route
Notificationnotifications
Recursive next hoprecursive-next-hop
Summarysummary
UFDMufdm
UFDM Detailufdm-detail
UFDM Summaryufdm-summary
Size of buffersize
Buffer sizesize_in_text
Enter an integer value for the event history buffersize_in_bytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2261
I Commandsip routing event-history
Page 2406
ip routing multicast event-history cli[no] ip routing multicast event-history cli { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Routing informationrouting
Configure multicastmulticast
Configure event history buffersevent-history
CLI events for MRIBcli
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2262
I Commandsip routing multicast event-history cli
Page 2407
ip routing multicast event-history mdt[no] ip routing multicast event-history mdt { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Routing informationrouting
Configure multicastmulticast
Configure event history buffersevent-history
MDT events for MRIBmdt
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2263
I Commandsip routing multicast event-history mdt
Page 2408
ip routing multicast event-history mfdm-debugs[no] ip routing multicast event-history mfdm-debugs { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Routing informationrouting
Configure multicastmulticast
Configure event history buffersevent-history
MFDM debugs for MRIBmfdm-debugs
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2264
I Commandsip routing multicast event-history mfdm-debugs
Page 2409
ip routing multicast event-history mfdm-events[no] ip routing multicast event-history mfdm-events { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Routing informationrouting
Configure mfdm-stats event-history buffermulticast
Configure event history buffersevent-history
Non-periodic MFDM events in MRIBmfdm-events
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2265
I Commandsip routing multicast event-history mfdm-events
Page 2410
ip routing multicast event-history mfdm-stats[no] ip routing multicast event-history mfdm-stats { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Routing informationrouting
Configure multicastmulticast
Configure event history buffersevent-history
MFDM-Stats events for MRIBmfdm-stats
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2266
I Commandsip routing multicast event-history mfdm-stats
Page 2411
ip routing multicast event-history nbm[no] ip routing multicast event-history nbm { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Routing informationrouting
Configure multicastmulticast
Configure event history buffersevent-history
NBM debugs for MRIBnbm
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2267
I Commandsip routing multicast event-history nbm
Page 2412
ip routing multicast event-history notify-clients[no] ip routing multicast event-history notify-clients { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Routing informationrouting
Configure multicastmulticast
Configure event history buffersevent-history
Clients notify debugs for MRIBnotify-clients
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2268
I Commandsip routing multicast event-history notify-clients
Page 2413
ip routing multicast event-history rib-summary[no] ip routing multicast event-history rib-summary { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Routing informationrouting
Configure multicastmulticast
Configure event-history buffersevent-history
RIB events for MRIB-summaryrib-summary
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2269
I Commandsip routing multicast event-history rib-summary
Page 2414
ip routing multicast event-history rib[no] ip routing multicast event-history rib { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Routing informationrouting
Configure multicastmulticast
Configure event-history buffersevent-history
RIB events for MRIBrib
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2270
I Commandsip routing multicast event-history rib
Page 2415
ip routing multicast event-history urib-debugs[no] ip routing multicast event-history urib-debugs { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Routing informationrouting
Configure multicastmulticast
Configure event history buffersevent-history
URIB debugs for MRIBurib-debugs
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2271
I Commandsip routing multicast event-history urib-debugs
Page 2416
ip routing multicast event-history vrf[no] ip routing multicast event-history vrf { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Routing informationrouting
Configure multicastmulticast
Configure event history buffersevent-history
VRF events for MRIBvrf
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2272
I Commandsip routing multicast event-history vrf
Page 2417
ip routing multicast file-debug[no] { ip | ipv4 } routing multicast file-debug
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IP featuresipv4
Routing informationrouting
Configure multicastmulticast
Collect all debugs to a filefile-debug
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2273
I Commandsip routing multicast file-debug
Page 2418
ip routing multicast holddown{ ip | ipv4 } routing multicast holddown { <route-holddown-sec> | <none> } | no { ip | ipv4 } routing multicastholddown [ <route-holddown-sec> | <none> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure IP featuresipv4
Routing informationrouting
Configure multicastmulticast
Initial holddown periodholddown
Delay in secondsroute-holddown-sec
Disable holddownnone
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2274
I Commandsip routing multicast holddown
Page 2419
ip routing multicast mfdm-buffer-route-count{ ip | ipv4 } routing multicast mfdm-buffer-route-count { <size> } | no { ip | ipv4 } routing multicastmfdm-buffer-route-count [ <size> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure IP featuresipv4
Routing informationrouting
Configure multicastmulticast
mfdm buffer route sizemfdm-buffer-route-count
size in numberssize
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2275
I Commandsip routing multicast mfdm-buffer-route-count
Page 2420
ip routing multicast software-replicate[no] ip routing multicast software-replicate [ iif ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Routing informationrouting
Configure multicastmulticast
Enable software replication of PIM ASM leak packetssoftware-replicate
(Optional) Enable software replication on incoming interfaceiif
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2276
I Commandsip routing multicast software-replicate
Page 2421
ip routing multicast trace enable[no] ip routing multicast trace enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure routing informationrouting
Configure multicastmulticast
Bintrace related commandstrace
Enable bintraceenable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2277
I Commandsip routing multicast trace enable
Page 2422
ip routing multicast trace entriesip routing multicast trace entries <num-entries>
Syntax Description
Configure IP featuresip
Configure routing informationrouting
Configure multicastmulticast
Bintrace related commandstrace
Number of bintrace entriesentries
Update number of bintrace entriesnum-entries
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2278
I Commandsip routing multicast trace entries
Page 2423
ip routing multicast trace recordsip routing multicast trace records <num-rec>
Syntax Description
Configure IP featuresip
Configure routing informationrouting
Configure multicastmulticast
Bintrace related commandstrace
Number of bintrace records per entryrecords
Update number of bintrace record per entrynum-rec
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2279
I Commandsip routing multicast trace records
Page 2424
ip secondaryip { <ipaddress> | <ipprefix> } secondary | no ip { <ipaddress> | <ipprefix> } secondary
Syntax Description
Negate a command or set its defaultsno
Enable HSRP IPv4 and set the virtual IP addressip
Virtual IP addressipaddress
Virtual IP address and mask lengthipprefix
Make this IP address a secondary virtual IP addresssecondary
Command Mode
• /exec/configure/if-eth-any/hsrp_ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2280
I Commandsip secondary
Page 2425
ip service-reflect destination to mask-len source[no] ip service-reflect [ <src-if> ] destination <in-grp> to <out-grp> mask-len <g-mlen> source <in-out-src>[ to <out-src> mask-len <s-mlen> ] [ sequence-number <seq-num> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Service reflect config commandservice-reflect
(Optional) Source Interface Namesrc-if
Translation informationdestination
Incoming Group Addressin-grp
to
Outgoing Group Addressout-grp
mask-len
Group Mask Lengthg-mlen
source
Source Addressin-out-src
(Optional)to
(Optional) Outgoing Source Addressout-src
(Optional)mask-len
(Optional) Source Mask Lengths-mlen
(Optional)sequence-number
(Optional) Sequence number of ruleseq-num
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2281
I Commandsip service-reflect destination to mask-len source
Page 2426
ip service-reflect mode regular[no] ip service-reflect mode { regular | fast-pass [ no-rewrite ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Service Reflect config commandservice-reflect
Select one-pass or three-pass modemode
Regular moderegular
Fast Pass Modefast-pass
(Optional) No Mac Rewriteno-rewrite
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2282
I Commandsip service-reflect mode regular
Page 2427
ip sla[no] ip sla <index>
Syntax Description
(Optional)no
ip
Service Level Agreement (SLA)sla
Entry Numberindex
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2283
I Commandsip sla
Page 2428
ip sla group schedule{ no ip sla group schedule <group-id> | ip sla group schedule <group-id> { { add <operation-ids> | delete<operation-ids> } | { <operation-ids> schedule-period <schedule-period-seconds> { [ ageout <ageout-seconds>] [ frequency { <frequency-seconds> | range <random-frequency-range> } ] [ life { forever | <life-seconds>} ] [ start-time { <hhmm> [ { January | February | March | April | May | June | July | August | September |October | November | December } <day> | <day> [ January | February | March | April | May | June | July |August | September | October | November | December ] ] | pending | now | after <hhmm> } ] } + } | reschedule} }
Syntax Description
no
deleteadd
(Optional) Januarystart-time
(Optional) NovemberOctober
<schedule-period-seconds>operation-ids
(Optional) <ageout-seconds>random-frequency-range
ip
Service Level Agreement (SLA)sla
Group Configuration or Group Schedulinggroup
Group schedulingschedule
Group schedule entry numbergroup-id
Delete probes from existing groupdelete
Reschedule the group using previous configreschedule
Multiple probe ID's to be group scheduledoperation-ids
Group schedule period rangeschedule-period
secondsschedule-period-seconds
(Optional) Group operation frequencyfrequency
(Optional) Group operation frequency-range for random schedulingrange
(Optional) Specify frequency in secondsfrequency-seconds
(Optional) How long to keep this Entry when inactiveageout
(Optional) Ageout Secondsageout-seconds
(Optional) Length of time to execute in secondslife
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2284
I Commandsip sla group schedule
Page 2429
(Optional) Life seconds (default 3600)life-seconds
(Optional) continue running foreverforever
(Optional) Start after a certain amount of time from nowafter
(Optional) Start time (hh:mm)hhmm
(Optional) Month of yearJanuary
(Optional) Month of yearFebruary
(Optional) Month of yearMarch
(Optional) Month of yearApril
(Optional) Month of yearMay
(Optional) Month of yearJune
(Optional) Month of yearJuly
(Optional) Month of yearAugust
(Optional) Month of yearSeptember
(Optional) Month of yearOctober
(Optional) Month of yearNovember
(Optional) Month of yearDecember
(Optional) Day of monthday
(Optional) Start nownow
(Optional) Start pendingpending
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2285
I Commandsip sla group schedule
Page 2430
ip sla logging traps[no] ip sla logging traps
Syntax Description
(Optional)no
ip
Service Level Agreement (SLA)sla
Enable Sysloglogging
Enable syslog trapstraps
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2286
I Commandsip sla logging traps
Page 2431
ip sla reaction-configuration react[no] ip sla reaction-configuration <react-cfg-entry-num> react <monitored-element> | ip slareaction-configuration <react-cfg-entry-num> react <monitored-element> { [ action-type <action> ] [threshold-value <rising-value> <falling-value> ] [ threshold-type { <neverImmed> | <consecutive> [<consecutive-occurances> ] | <xOfy> [ <x-value> <y-value> ] | <average> [ <n-attempts> ] } ] } +
Syntax Description
no
(Optional) threshold-valueaction-type
(Optional) <neverImmed>falling-value
(Optional) <x-value>consecutive-occurances
ip
Service Level Agreement (SLA)sla
IP SLAs Reaction-Configurationreaction-configuration
Entry Numberreact-cfg-entry-num
Reaction variable to be configuredreact
monitored elementmonitored-element
(Optional)action
(Optional) Threshold Valuethreshold-value
(Optional) Upper limit for Thresholdrising-value
(Optional) Threshold Typethreshold-type
(Optional)neverImmed
(Optional)consecutive
(Optional)xOfy
(Optional)average
(Optional) X valuex-value
(Optional) Y valuey-value
(Optional) N Valuen-attempts
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2287
I Commandsip sla reaction-configuration react
Page 2432
ip sla reaction-trigger[no] ip sla reaction-trigger <entry-num> <target-entry>
Syntax Description
(Optional)no
ip
Service Level Agreement (SLA)sla
IP SLAs Trigger Assignmentreaction-trigger
Entry Numberentry-num
Target entry Numbertarget-entry
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2288
I Commandsip sla reaction-trigger
Page 2433
ip sla resetip sla reset
Syntax Description
ip
Service Level Agreement (SLA)sla
IP SLAs Resetreset
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2289
I Commandsip sla reset
Page 2434
ip sla responder[no] ip sla responder [ { tcp-connect [ ipaddress<tcp-ip> ] port <tcp-port> } | { udp-echo [ ipaddress <udp-ip>] port <udp-port> } ]
Syntax Description
(Optional) ipaddresstcp-connect
(Optional)no
ip
sla
Enable IP SLAs Responderresponder
(Optional) Permanent addressipaddress
(Optional) Permanent portport
(Optional) Port Numbertcp-port
(Optional) Setup udp-echo responderudp-echo
(Optional) IP Address or IP HostNameudp-ip
(Optional) Port Numberudp-port
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2290
I Commandsip sla responder
Page 2435
ip sla responder twamp[no] ip sla responder twamp
Syntax Description
(Optional)no
ip
sla
Enable IP SLAs Responderresponder
Setup TWAMP respondertwamp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2291
I Commandsip sla responder twamp
Page 2436
ip sla restartip sla restart <index>
Syntax Description
ip
Service Level Agreement (SLA)sla
Restart An Active Entryrestart
Entry Numberindex
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2292
I Commandsip sla restart
Page 2437
ip sla schedule{ no ip sla schedule <index> | ip sla schedule <index> { [ life { <life-seconds> | forever } ] [ start-time {<hhmm> [ { January | February | March | April | May | June | July | August | September | October | November| December } <day> | <day> [ January | February | March | April | May | June | July | August | September |October | November | December ] ] | pending | now | { after <hhmm> } } ] [ ageout <ageout-seconds> ] [recurring ] } + }
Syntax Description
no
(Optional) foreverlife
(Optional) SeptemberAugust
(Optional) <life-seconds>recurring
ip
Service Level Agreement (SLA)sla
Entry Schedulingschedule
Entry Numberindex
(Optional) Life seconds (default 3600)life-seconds
(Optional) continue running foreverforever
(Optional) When to start this entrystart-time
(Optional) Start time (hh:mm)hhmm
(Optional) Month of yearJanuary
(Optional) Month of yearFebruary
(Optional) Month of yearMarch
(Optional) Month of yearApril
(Optional) Month of yearMay
(Optional) Month of yearJune
(Optional) Month of yearJuly
(Optional) Month of yearAugust
(Optional) Month of yearSeptember
(Optional) Month of yearOctober
(Optional) Month of yearNovember
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2293
I Commandsip sla schedule
Page 2438
(Optional) Month of yearDecember
(Optional) Day of monthday
(Optional) Start nownow
(Optional) Start after a certain amount of time from nowafter
(Optional) Start pendingpending
(Optional) How long to keep this Entry when inactiveageout
(Optional) Ageout Secondsageout-seconds
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2294
I Commandsip sla schedule
Page 2439
ip sla server twamp[no] ip sla server twamp
Syntax Description
(Optional)no
ip
sla
IPSLA IPPM server configurationserver
IPSLA IPPM TWAMP server configurationtwamp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2295
I Commandsip sla server twamp
Page 2440
ip source-route[no] ip source-route
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IP source routing optionsource-route
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2296
I Commandsip source-route
Page 2441
ip source binding vlan interface[no] ip source binding <ipaddr1> <macaddr> vlan <vlanid> interface <interface1>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
IP sourcesource
Static bindingbinding
IP addressipaddr1
MAC addressmacaddr
VLANvlan
VLAN idvlanid
interfaceinterface
interfaceinterface1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2297
I Commandsip source binding vlan interface
Page 2442
ip source icmp-errors[no] ip source <interface> icmp-errors
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure source-address for applicationssource
Interface to pick source-address frominterface
ICMP unreachable/TTL-exceeded/param-prob messagesicmp-errors
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2298
I Commandsip source icmp-errors
Page 2443
ip split-horizon eigrp[no] { ip | ipv6 } split-horizon eigrp <eigrp-ptag>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Configures IP-EIGRP split-horizon on interfacesplit-horizon
EIGRP interface configuration commandseigrp
Process tageigrp-ptag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2299
I Commandsip split-horizon eigrp
Page 2444
ip ssh source-interface[no] ip ssh source-interface <ifnum> [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure sshssh
Configure source interface feature for domain-lookupsource-interface
Source interfaceifnum
(Optional) Configure VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2300
I Commandsip ssh source-interface
Page 2445
ip summary-address eigrp ipv6 summary-address eigrp{ [ no ] ip summary-address eigrp <eigrp-ptag> { { <address> <mask> } | { <prefix> } } [ <distance> ] [leak-map <leak-map> ] | [ no ] ipv6 summary-address eigrp <eigrp-ptag> <ipv6-prefix> [ <distance> ] [leak-map <leak-map> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure IPv6 featuresipv6
Configures IP-EIGRP summary address on interfacesummary-address
EIGRP interface configuration commandseigrp
Process tageigrp-ptag
IP addressaddress
IP network maskmask
IP prefix in slash formatprefix
(Optional) Administrative distancedistance
(Optional) Allow dynamic prefixes based on the leak-mapleak-map
(Optional) leak-map nameleak-map
eigrp-ptag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2301
I Commandsip summary-address eigrp ipv6 summary-address eigrp
Page 2446
ip tacacs source-interface[no] ip tacacs source-interface | ip tacacs source-interface <interface>
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Tacacs servertacacs
Source interface to be used to reach tacacs serversource-interface
Interface Descriptioninterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2302
I Commandsip tacacs source-interface
Page 2447
ip tcp mss{ { no ip tcp mss } | { ip tcp mss <bytes> } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Global TCP parameterstcp
Maximum segment size for TCP connections in bytesmss
Maximum segment sizebytes
Command Mode
• /exec/configure /exec/configure/config-mgmt
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2303
I Commandsip tcp mss
Page 2448
ip tcp path-mtu-discovery{ { ip tcp path-mtu-discovery } | { no ip tcp path-mtu-discovery } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Global TCP parameterstcp
Enable path-MTU discovery on TCPpath-mtu-discovery
Command Mode
• /exec/configure /exec/configure/config-mgmt
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2304
I Commandsip tcp path-mtu-discovery
Page 2449
ip tcp synwait-time{ { no ip tcp synwait-time } | { ip tcp synwait-time <time> } }
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Global TCP parameterstcp
Set time to wait on new TCP connectionssynwait-time
Wait timetime
Command Mode
• /exec/configure /exec/configure/config-mgmt
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2305
I Commandsip tcp synwait-time
Page 2450
ip telnet source-interface[no] ip telnet source-interface <ifnum> [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure telnettelnet
Configure source interface feature for domain-lookupsource-interface
Source interfaceifnum
(Optional) Configure VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2306
I Commandsip telnet source-interface
Page 2451
ip tftp source-interface[no] ip tftp source-interface <ifnum> [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure TFTP clienttftp
Configure source interface feature for TFTP clientsource-interface
Source interfaceifnum
(Optional) Configure VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2307
I Commandsip tftp source-interface
Page 2452
ip traceroute source-interface[no] ip traceroute source-interface <ifnum> [ vrf { <vrf-name> | <vrf-known-name> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure traceroute clienttraceroute
Configure source interface feature for traceroutesource-interface
Source interfaceifnum
(Optional) Configure VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2308
I Commandsip traceroute source-interface
Page 2453
ip ttl[no] ip ttl <ttl_value>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set ERSPAN IP optionsip
Set the IP time-to-live valuettl
ttl_value
Command Mode
• /exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2309
I Commandsip ttl
Page 2454
ip udp relay addrgroup{ ip udp relay addrgroup <obj-grp-name> | no ip udp relay addrgroup }
Syntax Description
Configure IP featuresip
Negate a command or set its defaultsno
Enable/disable UDP forwardingudp
UDP relay agent parametersrelay
UDP Relay IP Address groupaddrgroup
Object grp Nameobj-grp-name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2310
I Commandsip udp relay addrgroup
Page 2455
ip udp relay subnet-broadcast[no] ip udp relay subnet-broadcast
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Enable/disable UDP forwardingudp
UDP relay agent parametersrelay
Enable/disable UDP forwarding for subnet-broadcastsubnet-broadcast
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2311
I Commandsip udp relay subnet-broadcast
Page 2456
ip unnumberedip unnumbered <interface> | no ip unnumbered [ <interface> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure interface as unnumberedunnumbered
Interface with IP addressinterface
Command Mode
• /exec/configure/ppm-ethernet-switch /exec/configure/if-p2p /exec/configure/if-gre-tunnel/exec/configure/if-any-tunnel /exec/configure/if-port-channel-sub /exec/configure/if-vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2312
I Commandsip unnumbered
Page 2457
ip unreachables[no] ip unreachables
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Enable sending ICMP unreachables (other than port-unreachable)unreachables
Command Mode
• /exec/configure/if-igp /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2313
I Commandsip unreachables
Page 2458
ip verify source dhcp-snooping-vlan[no] ip verify source dhcp-snooping-vlan
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresip
Configure Unicast Reverse Path Forwarding or IP Source Guardverify
IP Source Guard related commandssource
Vlans on which snooping is enableddhcp-snooping-vlan
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2314
I Commandsip verify source dhcp-snooping-vlan
Page 2459
ip verify unicast source reachable-via rx[no] ip verify unicast source reachable-via [ { rx | any [ allow-default ] } [ policy { <policy-name> |<acl_pol_name> } ] ] | ip verify unicast source reachable-via { rx | any [ allow-default ] } [ policy {<policy-name> | <acl_pol_name> } ]
Syntax Description
Negate a command or set its defaultsno
Configure IP featuresip
Configure Unicast Reverse Path Forwarding or IP Source Guardverify
Unicast Reverse Path Forwardingunicast
Validation of source addresssource
Specify reachability check to apply to the source addressreachable-via
(Optional) Source is reachable via interface on which packet wasreceived
rx
(Optional) Source is reachable via any interfaceany
(Optional) Loose Default Route Unicast Reverse Path Forwardingallow-default
(Optional) Unicast Reverse Path Forwarding fail policypolicy
(Optional) An uRPF fail policy namepolicy-name
(Optional) An existing access-rules policyacl_pol_name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2315
I Commandsip verify unicast source reachable-via rx
Page 2460
ipv6{ [ <seqno> ] | no } <permitdeny> { ipv6 | <proto> | <ipv6_other_proto> } { <src_any> | { <src_addr><src_wild> } | <src_prefix> | { src_key_host <src_host> } | { src_key_addrgrp <src_addrgrp_name> } } {<dst_any> | { <dst_addr> <dst_wild> } | <dst_prefix> | { dst_key_host <dst_host> } | { dst_key_addrgrp<dst_addrgrp_name> } } { [ { dscp { <dscp_num> | <dscp_str> } } ] [ { flow-label <flow_num> } ] [ fragments] [ log ] [ time-range <time_range_name> ] [ packet-length { <plen_op> <plen0> | <plen_range> <plen1><plen2> } ] [ { udf { <udf_name> <udf_val> <udf_mask> } + } ] } + [ vlan <vlanid> | ingress_intf { <intfid>| <intfname> } | vlan_priority <vlanpriorityid> ] + [ { udf { <udf_name> <udf_val> <udf_mask> } + } ] [capture session <session-id> ] { [ <actionv6> <actionidv6> ] }
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Permit/denypermitdeny
Any IPV6 protocolipv6
A protocol numberproto
ipv6_other_protoipv6_other_proto
(Optional) Configure match based on vlanvlan
(Optional) Configure match based on ingress interfaceingress_intf
(Optional) Configure match based on priorityvlan_priority
(Optional) User defined field matchudf
(Optional) UDF nameudf_name
(Optional) UDF value to matchudf_val
(Optional) Mask to apply to UDF valueudf_mask
(Optional) VLAN numbervlanid
(Optional) Interface indexintfid
(Optional) Interface nameintfname
(Optional) Vlan Priorityvlanpriorityid
Anysrc_any
A single source hostsrc_key_host
Source address groupsrc_key_addrgrp
Address group namesrc_addrgrp_name
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2316
I Commandsipv6
Page 2461
Anydst_any
A single destination hostdst_key_host
Destination address groupdst_key_addrgrp
Address group namedst_addrgrp_name
(Optional) Match packets with given dscp valuedscp
(Optional) Differentiated services codepoint valuedscp_num
(Optional) Differentiated services codepoint labeldscp_str
(Optional) Flow labelflow-label
(Optional) Flow label valueflow_num
(Optional) Check non-initial fragmentsfragments
(Optional) Log matches against this entrylog
(Optional) Specify a time rangetime-range
(Optional) Time range nametime_range_name
(Optional) Match packets based on layer 3 packet lengthpacket-length
(Optional) Packet-length operatorplen_op
(Optional) Packet-length rangeplen_range
(Optional) Packet lengthplen0
(Optional) Lower packet lengthplen1
(Optional) Higher packet lengthplen2
(Optional) Enable packet capture on this filter for sessioncapture
(Optional) Session ID <1-48> for this sessionsession
(Optional) Session ID <1-48> for this sessionsession-id
(Optional) ActionV6actionv6
(Optional) redirect: Ethernet1/1,port-channel1 set-erspan-dscp: <1-63>set-erspan-gre-proto: <1-65535>
actionidv6
Command Mode
• /exec/configure/ipv6acl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2317
I Commandsipv6
Page 2462
ipv6 access-class[no] ipv6 access-class <name> <inout>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Specify IPv6 access control for packetsaccess-class
List namename
Traffic directioninout
Command Mode
• /exec/configure/line
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2318
I Commandsipv6 access-class
Page 2463
ipv6 access-list[no] ipv6 access-list <name> [ client <clienttype> <clientID> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure access listaccess-list
List namename
(Optional) set client typeclient
(Optional) CLI/ONEPclienttype
(Optional) client appIDclientID
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2319
I Commandsipv6 access-list
Page 2464
ipv6 access-list match-local-traffic[no] ipv6 access-list match-local-traffic | ipv6 access-list match-local-traffic
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure access listaccess-list
Enable access-list matching for locally generated trafficmatch-local-traffic
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2320
I Commandsipv6 access-list match-local-traffic
Page 2465
ipv6 address[no] ipv6 address [ { autoconfig [ default ] | [ <ipv6-prefix> [ eui64 ] [ route-preference <pref> ] [ tag <tag>] [ anycast ] ] } ] | ipv6 address { autoconfig [ default ] | [ <ipv6-prefix> [ eui64 ] [ route-preference <pref> ][ tag <tag> ] [ anycast ] ] }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure IPv6 address on interfaceaddress
(Optional) Configure IPv6 Stateless address autoconfigautoconfig
(Optional) For SLAAC, adds default route and the nh would be fetchedfrom RA source address
default
(Optional) Configure Extended Unique Identifier for the low-order 64bits
eui64
(Optional) Configure IPv6 anycast address on interfaceanycast
(Optional) U6RIB route preference for local/direct routesroute-preference
(Optional) Local/direct route preferencepref
(Optional) U6RIB route tag value for local/direct routestag
(Optional) Local/direct tag valuetag
Command Mode
• /exec/configure/if-igp /exec/configure/if-any-tunnel /exec/configure/if-vsan /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2321
I Commandsipv6 address
Page 2466
ipv6 address dhcp[no] ipv6 address dhcp
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure IPv6 address on interfaceaddress
Configure IPv6 address from a dhcp serverdhcp
Command Mode
• /exec/configure/if-vlan /exec/configure/if-ethernet /exec/configure/if-mgmt-config/exec/configure/if-ethernet-all /exec/configure/if-sub
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2322
I Commandsipv6 address dhcp
Page 2467
ipv6 address use-link-local-only[no] ipv6 address use-link-local-only | ipv6 address use-link-local-only
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure IPv6 address on interfaceaddress
Enable IPv6 on interface using only a single link-local addressuse-link-local-only
Command Mode
• /exec/configure/if-igp /exec/configure/if-mgmt-config /exec/configure/if-gre-tunnel/exec/configure/if-6to4-tunnel /exec/configure/if-vsan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2323
I Commandsipv6 address use-link-local-only
Page 2468
ipv6 adjacency-stale-timer{ { ipv6 [ icmp ] adjacency-stale-timer <stale-time> } | { no ipv6 [ icmp ] adjacency-stale-timer [ <stale-time>] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) Configure icmp parametersicmp
When probing for an adjacency beginsadjacency-stale-timer
Seconds after adjacency uptimestale-time
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2324
I Commandsipv6 adjacency-stale-timer
Page 2469
ipv6 adjacency route distance{ ipv6 adjacency route distance <pref> } | { no ipv6 adjacency route distance }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure Adjmgradjacency
routeroute
admin-distancedistance
preferencepref
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2325
I Commandsipv6 adjacency route distance
Page 2470
ipv6 amt gateway[no] ipv6 amt gateway
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
AMT global configuration commandsamt
Configures IPv6 AMT gateway functionalitygateway
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2326
I Commandsipv6 amt gateway
Page 2471
ipv6 amt relay[no] ipv6 amt relay
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
AMT global configuration commandsamt
Configures IPv6 AMT relay functionalityrelay
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2327
I Commandsipv6 amt relay
Page 2472
ipv6 destination{ ipv6 { destination | source } <addr> } | { no ipv6 { destination | source } }
Syntax Description
Negate a command or set its defaultsno
specify flow ipv6 addressipv6
specify flow source ipv6 addresssource
specify flow destination ipv6 addressdestination
Command Mode
• /exec/configure/configngoamprofileflow
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2328
I Commandsipv6 destination
Page 2473
ipv6 dhcp-ldra[no] ipv6 dhcp-ldra
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Enable/disable DHCPV6 LDRAdhcp-ldra
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2329
I Commandsipv6 dhcp-ldra
Page 2474
ipv6 dhcp-ldra attach-policy[no] ipv6 dhcp-ldra attach-policy { client-facing-trusted | client-facing-untrusted | client-facing-disable |server-facing }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
DHCPv6 LDRAdhcp-ldra
Apply a policy for DHCPV6 LDRAattach-policy
Client facing trusted portclient-facing-trusted
Client facing untrusted portclient-facing-untrusted
Disable LDRA on portclient-facing-disable
Server facing portserver-facing
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2330
I Commandsipv6 dhcp-ldra attach-policy
Page 2475
ipv6 dhcp-ldra attach-policy vlan client[no] ipv6 dhcp-ldra attach-policy vlan <vlan-id10> { client-facing-trusted | client-facing-untrusted }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
DHCPv6 LDRAdhcp-ldra
Apply a policy for DHCPV6 LDRAattach-policy
DHCP LDRA vlanvlan
VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19vlan-id10
Client facing trustedclient-facing-trusted
Client facing untrustedclient-facing-untrusted
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2331
I Commandsipv6 dhcp-ldra attach-policy vlan client
Page 2476
ipv6 dhcp guard[no] ipv6 dhcp guard [ attach-policy <policy_name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) policy name for feature DHCP Guardpolicy_name
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2332
I Commandsipv6 dhcp guard
Page 2477
ipv6 dhcp guard[no] ipv6 dhcp guard [ attach-policy <policy_name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) policy name for feature DHCP Guardpolicy_name
Command Mode
• /exec/configure/vlan-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2333
I Commandsipv6 dhcp guard
Page 2478
ipv6 dhcp guard policy[no] ipv6 dhcp guard policy <policy_name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Name of the dhcp guard policypolicy_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2334
I Commandsipv6 dhcp guard policy
Page 2479
ipv6 dhcp relay[no] ipv6 dhcp relay
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure DHCPv6 relaydhcp
Configure DHCPv6 relay agentrelay
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2335
I Commandsipv6 dhcp relay
Page 2480
ipv6 dhcp relay address[no] ipv6 dhcp relay address [ <ip-addr-val> [ use-vrf <vrf-name> ] [ interface <interface-name> ] ] | no ipv6dhcp relay address [ <ip-addr-val> [ interface <interface-name> ] [ use-vrf <vrf-name> ] ]
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure DHCPv6 relaydhcp
Configure DHCPv6 relay agentrelay
Configure DHCPv6 server relay addressaddress
(Optional) server address VRF membershipuse-vrf
(Optional) VRF namevrf-name
(Optional) Destination interface for the relay addressinterface
(Optional) Destination interfaceinterface-name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2336
I Commandsipv6 dhcp relay address
Page 2481
ipv6 dhcp relay address ipv6 dhcp relay addressipv6 dhcp relay address <ip-addr-val> [ use-vrf <vrf-name> ] [ interface <interface-name> ] | ipv6 dhcp relayaddress <ip-addr-val> [ interface <interface-name> ] [ use-vrf <vrf-name> ]
Syntax Description
Configure IPv6 featuresipv6
Configure DHCPv6 relaydhcp
Configure DHCPv6 relay agentrelay
Configure DHCPv6 server relay addressaddress
(Optional) server address VRF membershipuse-vrf
(Optional) VRF namevrf-name
(Optional) Destination interface for the relay addressinterface
(Optional) Destination interfaceinterface-name
Command Mode
• /exec/configure/if-igp /exec/configure/ppm-ethernet-switch /exec/configure/ppm-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2337
I Commandsipv6 dhcp relay address ipv6 dhcp relay address
Page 2482
ipv6 dhcp relay option type cisco[no] ipv6 dhcp relay option type cisco
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure DHCPv6 relaydhcp
DHCPv6 relay agent parametersrelay
Relay agent optionoption
Relay agent option typetype
Use Cisco propritery optionscisco
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2338
I Commandsipv6 dhcp relay option type cisco
Page 2483
ipv6 dhcp relay option vpn[no] ipv6 dhcp relay option vpn
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure DHCPv6 relaydhcp
DHCPv6 relay agent parametersrelay
Insert DHCPv6 relay information in Relay forwardoption
Enable DHCPv6 relay support across VRFsvpn
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2339
I Commandsipv6 dhcp relay option vpn
Page 2484
ipv6 dhcp relay source-interfaceipv6 dhcp relay source-interface <interface-name>
Syntax Description
Configure IPv6 featuresipv6
Configure DHCPv6 relaydhcp
Configure DHCPv6 relay agentrelay
Configure source interface for DHCPv6 relaysource-interface
Source interfaceinterface-name
Command Mode
• /exec/configure /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2340
I Commandsipv6 dhcp relay source-interface
Page 2485
ipv6 dhcp relay source-interface[no] ipv6 dhcp relay source-interface
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure DHCPv6 relaydhcp
Configure DHCPv6 relay agentrelay
Configure source interface for DHCPv6 relaysource-interface
Command Mode
• /exec/configure /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2341
I Commandsipv6 dhcp relay source-interface
Page 2486
ipv6 flow monitor input[no] ipv6 flow monitor <monitorname> input
Syntax Description
Configure IPv6 featuresipv6
NetFlow related commandsflow
Apply a Flow Monitor to this interfacemonitor
Name of Flow Monitormonitorname
Apply Flow Monitor on input trafficinput
Command Mode
• /exec/configure/if-routing /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2342
I Commandsipv6 flow monitor input
Page 2487
ipv6 flow monitor input[no] ipv6 flow monitor <monitorname> input
Syntax Description
Configure IPv6 featuresipv6
NetFlow related commandsflow
Apply a Flow Monitor to this interfacemonitor
Name of Flow Monitormonitorname
Apply Flow Monitor on input trafficinput
Command Mode
• /exec/configure/vlan-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2343
I Commandsipv6 flow monitor input
Page 2488
ipv6 flow monitor input[no] ipv6 flow monitor <monitorname> input
Syntax Description
Configure IPv6 featuresipv6
NetFlow related commandsflow
Apply a Flow Monitor to this interfacemonitor
Name of Flow Monitormonitorname
Apply Flow Monitor on input trafficinput
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2344
I Commandsipv6 flow monitor input
Page 2489
ipv6 forwardipv6 forward | no ipv6 forward
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Enable ipv6 forwarding on interfaceforward
Command Mode
• /exec/configure/if-vlan /exec/configure/if-vlan-range
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2345
I Commandsipv6 forward
Page 2490
ipv6 host[no] ipv6 host <s0> [ <ipv6_0> ] | ipv6 host <s0> <ipv6_0>
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Add an entry to the ip hostname tablehost
Name of Hosts0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2346
I Commandsipv6 host
Page 2491
ipv6 link-local[no] ipv6 link-local [ <ipv6-addr> ] | ipv6 link-local <ipv6-addr>
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Change format of link-local addresslink-local
Command Mode
• /exec/configure/if-vlan /exec/configure/if-mgmt-config /exec/configure/if-gre-tunnel/exec/configure/if-6to4-tunnel /exec/configure/if-igp /exec/configure/if-vsan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2347
I Commandsipv6 link-local
Page 2492
ipv6 local policy route-mapipv6 local policy route-map <route-map-name> | no ipv6 local policy route-map [ <route-map-name> |<route-map-name> ]
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure local PBR featurelocal
Configure PBR featurepolicy
Route-map for PBRroute-map
Route-map nameroute-map-name
(Optional) Route-map nameroute-map-name
(Optional) Known route-map nameroute-map-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2348
I Commandsipv6 local policy route-map
Page 2493
ipv6 mld group-timeout{ { no ipv6 [ icmp ] mld group-timeout [ <time> ] } | { ipv6 [ icmp ] mld group-timeout <time> } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
Configures group membership timeoutgroup-timeout
(Optional) Time in secondstime
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2349
I Commandsipv6 mld group-timeout
Page 2494
ipv6 mld immediate-leave[no] ipv6 [ icmp ] mld immediate-leave
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
Enable/Disable immediate leaveimmediate-leave
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2350
I Commandsipv6 mld immediate-leave
Page 2495
ipv6 mld join-group[no] ipv6 [ icmp ] mld join-group { { <group> [ source <source> ] } | { route-map <route-map-name> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
Configures local group membership for routerjoin-group
(Optional) Configures source address for MLDv2 (S,G) channelsource
Join group policyroute-map
route-map nameroute-map-name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2351
I Commandsipv6 mld join-group
Page 2496
ipv6 mld last-member-query-count{ { no ipv6 [ icmp ] mld last-member-query-count [ <count> ] } | { ipv6 [ icmp ] mld last-member-query-count<count> } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
Configures number of group-specific Queries sentlast-member-query-count
(Optional) Count valuecount
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2352
I Commandsipv6 mld last-member-query-count
Page 2497
ipv6 mld last-member-query-response-time{ { no ipv6 [ icmp ] mld last-member-query-response-time [ <interval> ] } | { ipv6 [ icmp ] mldlast-member-query-response-time <interval> } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
Configures last member query response timelast-member-query-response-time
(Optional) Interval in secondsinterval
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2353
I Commandsipv6 mld last-member-query-response-time
Page 2498
ipv6 mld querier{ { no ipv6 [ icmp ] mld { querier-timeout | query-timeout } [ <time> ] } | { ipv6 [ icmp ] mld { querier-timeout| query-timeout } <time> } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
Configures querier timeout for MLDv1query-timeout
Configures querier timeout for MLDv1querier-timeout
(Optional) Time in secondstime
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2354
I Commandsipv6 mld querier
Page 2499
ipv6 mld query-interval{ { no ipv6 [ icmp ] mld query-interval [ <interval> ] } | { ipv6 [ icmp ] mld query-interval <interval> } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
Configures interval between Query transmissionquery-interval
(Optional) Interval in secondsinterval
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2355
I Commandsipv6 mld query-interval
Page 2500
ipv6 mld query-max-response-time{ { no ipv6 [ icmp ] mld query-max-response-time [ <time> ] } | { ipv6 [ icmp ] mld query-max-response-time<time> } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
Configures MRT for query messagesquery-max-response-time
(Optional) Time in secondstime
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2356
I Commandsipv6 mld query-max-response-time
Page 2501
ipv6 mld report-link-local-groups[no] ipv6 [ icmp ] mld report-link-local-groups
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
Send Reports for groups in ff02::/16report-link-local-groups
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2357
I Commandsipv6 mld report-link-local-groups
Page 2502
ipv6 mld report{ { ipv6 [ icmp ] mld { report-policy | access-group } <route-map-name> } | { no ipv6 [ icmp ] mld {report-policy | access-group } [ <route-map-name> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
ICMPv6 MLD Report Policyreport-policy
ICMPv6 MLD access-groupaccess-group
Route-map nameroute-map-name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2358
I Commandsipv6 mld report
Page 2503
ipv6 mld robustness-variable{ { no ipv6 [ icmp ] mld robustness-variable [ <value> ] } | { ipv6 [ icmp ] mld robustness-variable <value>} }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
Configures RFC defined Robustness Variablerobustness-variable
(Optional) Count valuevalue
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2359
I Commandsipv6 mld robustness-variable
Page 2504
ipv6 mld ssm-translate[no] ipv6 [ icmp ] mld ssm-translate <group> <source>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) Configure icmp parametersicmp
Multicast Listener Discovery commandsmld
Translate MLDv1 reports to (S,G) route entriesssm-translate
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2360
I Commandsipv6 mld ssm-translate
Page 2505
ipv6 mld startup-query-count{ { no ipv6 [ icmp ] mld startup-query-count [ <count> ] } | { ipv6 [ icmp ] mld startup-query-count <count>} }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
Configures number of queries sent at startupstartup-query-count
(Optional) Count valuecount
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2361
I Commandsipv6 mld startup-query-count
Page 2506
ipv6 mld startup-query-interval{ { no ipv6 [ icmp ] mld startup-query-interval [ <interval> ] } | { ipv6 [ icmp ] mld startup-query-interval<interval> } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
Configures query interval at startupstartup-query-interval
(Optional) Interval in secondsinterval
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2362
I Commandsipv6 mld startup-query-interval
Page 2507
ipv6 mld state-limit{ { ipv6 [ icmp ] mld state-limit <max-states> [ reserved <route-map-name> <max-reserved> ] } | { no ipv6[ icmp ] mld state-limit [ <max-states> [ reserved <route-map-name> <max-reserved> ] ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
Configures State limitstate-limit
Maximum states allowedmax-states
(Optional) Reserve the states using route-mapreserved
(Optional) Route-map nameroute-map-name
(Optional) Maximum (*,G)/(S,G) entires allowed on the interfacemax-reserved
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2363
I Commandsipv6 mld state-limit
Page 2508
ipv6 mld static[no] ipv6 [ icmp ] mld { static-group | static-oif } { { <group> [ source <source> ] } | { route-map<route-map-name> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Multicast Listener Discovery commandsmld
Configures static oif for a multicast forwarding entrystatic-group
Configures static oif for a multicast forwarding entrystatic-oif
(Optional) Configures source address for MLDv2 (S,G) Channelsource
Static group policyroute-map
route-map nameroute-map-name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2364
I Commandsipv6 mld static
Page 2509
ipv6 mld version{ { no ipv6 mld version [ <version> ] } | { ipv6 mld version <version> } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Multicast Listener Discovery commandsmld
Configures MLD version number for interfaceversion
(Optional) Version number valueversion
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2365
I Commandsipv6 mld version
Page 2510
ipv6 nd cache limit{ { ipv6 nd cache limit <max> } | { no ipv6 nd cache limit } } [ syslog <rate> ]
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
ND cache parameterscache
Limit size of ND adjacencies cachelimit
Max no of ND adjacencies configuredmax
(Optional) Syslog messagessyslog
(Optional) Syslogs per secondrate
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2366
I Commandsipv6 nd cache limit
Page 2511
ipv6 nd dad attemptsipv6 nd dad attempts <attempt> | no ipv6 nd dad attempts
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Duplicate Address Detectiondad
Set IPv6 Duplicate Address Detection Transmitsattempts
Number of attemptsattempt
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2367
I Commandsipv6 nd dad attempts
Page 2512
ipv6 nd dadns-discover{ ipv6 nd dadns-discover <dadns_interval> } | { no ipv6 nd dadns-discover }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Discover host from DADNSdadns-discover
Interval in millisecondsdadns_interval
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2368
I Commandsipv6 nd dadns-discover
Page 2513
ipv6 nd hop-limit{ { ipv6 nd hop-limit <hop-limit> } | { no ipv6 nd hop-limit [ <hop-limit> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Sent in RAmessages, tells hosts what hop-limit to use when originatingIPv6 packets
hop-limit
Hop limit in IPv6 headerhop-limit
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2369
I Commandsipv6 nd hop-limit
Page 2514
ipv6 nd mac-extract[no] ipv6 nd mac-extract [ exclude nud-phase ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Extract next hop MAC address embedded in IPV6 addressmac-extract
(Optional) Excludeexclude
(Optional) during NUD phasenud-phase
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2370
I Commandsipv6 nd mac-extract
Page 2515
ipv6 nd managed-config-flag[no] ipv6 nd managed-config-flag
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Sent in RA messages, tells hosts to use stateful addressauto-configuration to obtain address information
managed-config-flag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2371
I Commandsipv6 nd managed-config-flag
Page 2516
ipv6 nd mtu{ { ipv6 nd mtu <mtu> } | { no ipv6 nd mtu [ <mtu> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Sent in RA messages, tells hosts what MTU to use on this linkmtu
MTU in bytesmtu
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2372
I Commandsipv6 nd mtu
Page 2517
ipv6 nd ns-interval{ { ipv6 nd ns-interval <interval> [ <retry-count> ] } | { no ipv6 nd ns-interval [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Retransmission interval between sendingNeighbor-Solicitationmessagesns-interval
Interval in millisecondsinterval
(Optional) NS Retry countretry-count
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2373
I Commandsipv6 nd ns-interval
Page 2518
ipv6 nd off-list timeout{ ipv6 nd off-list timeout <time> } | { no ipv6 nd off-list timeout }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Display Neighbor Discovery interface informationnd
off-listoff-list
Expire timetimeout
Expire time value in secondstime
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2374
I Commandsipv6 nd off-list timeout
Page 2519
ipv6 nd other-config-flag[no] ipv6 nd other-config-flag
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Sent in RA messages, tells hosts to use stateful auto-configuration toobtain non-address related information
other-config-flag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2375
I Commandsipv6 nd other-config-flag
Page 2520
ipv6 nd prefix{ { ipv6 nd prefix <prefix> [ { <val-life> | infinite } { <perf-life> | infinite } [ [ no-autoconfig ] [ no-onlink ][ no-rtr-address ] [ off-link ] ] | no-advertise ] } | { no ipv6 nd prefix <prefix> } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
IPv6 Prefix to advertise in RAprefix
(Optional) Valid Lifetime (secs)val-life
(Optional) Infinite Valid Lifetimeinfinite
(Optional) Do not advertise prefixno-advertise
(Optional) Preferred Lifetime (secs)perf-life
(Optional) Infinite Preferred Lifetimeinfinite
(Optional) Do not use prefix for autoconfigurationno-autoconfig
(Optional) Do not use prefix for onlink determinationno-onlink
(Optional) Do not send full router address in prefix advertno-rtr-address
(Optional) Prefix is offlinkoff-link
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2376
I Commandsipv6 nd prefix
Page 2521
ipv6 nd prefix default{ { ipv6 nd prefix default [ { <val-life> | infinite } { <perf-life> | infinite } [ [ no-autoconfig ] [ no-onlink ] [no-rtr-address ] [ off-link ] ] | no-advertise ] } | { no ipv6 nd prefix default } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
IPv6 Prefix to advertise in RAprefix
Specify prefix default parametersdefault
(Optional) Valid Lifetime (secs)val-life
(Optional) Infinite Valid Lifetimeinfinite
(Optional) Do not advertise prefixno-advertise
(Optional) Preferred Lifetime (secs)perf-life
(Optional) Infinite Preferred Lifetimeinfinite
(Optional) Do not use prefix for autoconfigurationno-autoconfig
(Optional) Do not use prefix for onlink determinationno-onlink
(Optional) Do not send full router address in prefix advertno-rtr-address
(Optional) Prefix is offlinkoff-link
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2377
I Commandsipv6 nd prefix default
Page 2522
ipv6 nd ra-intervalipv6 nd ra-interval <interval> [ min <min-interval> ] | no ipv6 nd ra-interval [ <interval> ] [ min <min-interval>]
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Interval between sending Router-Advertisement messagesra-interval
Interval in secondsinterval
(Optional) Minimum interval between sending RA messagesmin
(Optional) Interval in secondsmin-interval
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2378
I Commandsipv6 nd ra-interval
Page 2523
ipv6 nd ra-lifetime{ { ipv6 nd ra-lifetime <lifetime> } | { no ipv6 nd ra-lifetime [ <lifetime> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Sent in RA messages, Router Lifetime of a default router, 0 means thisrouter will not be the default router
ra-lifetime
Lifetime in secondslifetime
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2379
I Commandsipv6 nd ra-lifetime
Page 2524
ipv6 nd ra dns search-list sequence[no] ipv6 nd ra dns search-list <dnssl> [ { <dnssl_life> | infinite } ] sequence <seqno>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Router Advertisementra
Domain Name Systemdns
DNS Search Listsearch-list
Configure DNS Search List to advertise in RAdnssl
(Optional) Configure IPv6 DNS Search list life timednssl_life
(Optional) Configure IPv6 DNS Search list life time with infiniteinfinite
Sequence of Search Listsequence
Sequence numberseqno
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2380
I Commandsipv6 nd ra dns search-list sequence
Page 2525
ipv6 nd ra dns search-list suppress[no] ipv6 nd ra dns search-list suppress
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Router Advertisementra
Domain Name Systemdns
DNS Search Listsearch-list
Disable sending DNSSL in Router-Advertisement messagessuppress
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2381
I Commandsipv6 nd ra dns search-list suppress
Page 2526
ipv6 nd ra dns server sequence[no] ipv6 nd ra dns server <ipv6_addr> [ { <rdnss_life> | infinite } ] sequence <seqno>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Router Advertisementra
Domain Name Systemdns
Domain Name System Serverserver
(Optional) Configure IPv6 DNS Server life timerdnss_life
(Optional) Configure IPv6 DNS Server life time with infiniteinfinite
Sequence of Serversequence
Sequence numberseqno
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2382
I Commandsipv6 nd ra dns server sequence
Page 2527
ipv6 nd ra dns server suppress[no] ipv6 nd ra dns server suppress
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Router Advertisementra
Domain Name Systemdns
Domain Name System Serverserver
Disable sending RDNSS in Router-Advertisement messagessuppress
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2383
I Commandsipv6 nd ra dns server suppress
Page 2528
ipv6 nd ra route suppress[no] ipv6 nd ra route suppress
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Router Advertisementra
Route Information Option in RFC 4191route
Disable sending Route Information Options in RA messagessuppress
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2384
I Commandsipv6 nd ra route suppress
Page 2529
ipv6 nd raguard[no] ipv6 nd raguard
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure IPv6 NDnd
Configure RA guardraguard
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2385
I Commandsipv6 nd raguard
Page 2530
ipv6 nd raguard[no] ipv6 nd raguard [ attach-policy <policy_name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) policy name for ipv6 raguardpolicy_name
Command Mode
• /exec/configure/vlan-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2386
I Commandsipv6 nd raguard
Page 2531
ipv6 nd raguard attach-policy[no] ipv6 nd raguard attach-policy <policy_name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
policy name for feature RA guardpolicy_name
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2387
I Commandsipv6 nd raguard attach-policy
Page 2532
ipv6 nd raguard policy[no] ipv6 nd raguard policy <policy_name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Name of the raguard policypolicy_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2388
I Commandsipv6 nd raguard policy
Page 2533
ipv6 nd reachable-time{ { ipv6 nd reachable-time <time> } | { no ipv6 nd reachable-time [ <time> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Sent in RAmessages, advertised timewhen a node considers a neighborup after receiving a reachability confirmation
reachable-time
Time in millisecondstime
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2389
I Commandsipv6 nd reachable-time
Page 2534
ipv6 nd retrans-timer{ { ipv6 nd retrans-timer <time> } | { no ipv6 nd retrans-timer [ <time> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Sent in RA messages, advertised time between NS messagesretrans-timer
Time in millisecondstime
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2390
I Commandsipv6 nd retrans-timer
Page 2535
ipv6 nd route route-preference High Low Medium infinite{ { ipv6 nd route <prefix> route-preference { High | Low | Medium } { <lifetime> | infinite } [ {verify-reachability } ] } | { no ipv6 nd route { <prefix> | all } route-preference } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Route Information Option in RFC 4191route
Route preference valueroute-preference
High router preferenceHigh
Low router preferenceLow
Medium router preferenceMedium
Lifetime (secs)lifetime
Infinite lifetime of prefixinfinite
(Optional) Verify if route is present in Route tableverify-reachability
Remove all the Router Preference prefixesall
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2391
I Commandsipv6 nd route route-preference High Low Medium infinite
Page 2536
ipv6 nd router-preference High Low Medium{ { ipv6 nd router-preference { High | Low | Medium } } | { no ipv6 nd router-preference } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Set default router preference valuerouter-preference
High default router preferenceHigh
Low default router preferenceLow
Medium default router preferenceMedium
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2392
I Commandsipv6 nd router-preference High Low Medium
Page 2537
ipv6 nd solicit-na accept{ ipv6 nd solicit-na { { accept [ no-probe | <interval> ] | [ no-accept ] } | { accept1 [ no-probe1 | <interval1>] | [ no-accept1 ] } } } | { no ipv6 nd solicit-na }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Solicited Neighbor Advertisemensolicit-na
Accept Solicit NA without incomplete entryaccept
(Optional) Do not probe, create a Reachable Entryno-probe
(Optional) Probe Interval in Secondsinterval
(Optional) Do not accept Solicit NA without incomplete entryno-accept
Accept Solicit NA without incomplete entryaccept1
(Optional) Do not probe, create a Reachable Entryno-probe1
(Optional) Probe Interval in Secondsinterval1
(Optional) Do not accept Solicit NA without incomplete entryno-accept1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2393
I Commandsipv6 nd solicit-na accept
Page 2538
ipv6 nd suppress-ra[no] ipv6 nd suppress-ra [ mtu ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
ICMPv6 Neighbor Discovery commandsnd
Disable sending Router-Advertisement messagessuppress-ra
(Optional) Disable sending MTU in Router-Advertisement messagesmtu
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2394
I Commandsipv6 nd suppress-ra
Page 2539
ipv6 nd synchronizeipv6 nd synchronize [ pull | push ]
Syntax Description
Configure IPv6 featuresipv6
Display Neighbor Discovery interface informationnd
CFS synchronizesynchronize
(Optional) Initiate CFS pull requestpull
(Optional) Initiate CFS push messagepush
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2395
I Commandsipv6 nd synchronize
Page 2540
ipv6 neighbor[no] ipv6 neighbor <ipv6-addr> [ <mac-addr> ] | ipv6 neighbor <ipv6-addr> <mac-addr>
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure IPv6 address to layer-2 address mappingneighbor
(Optional) Layer-2 MAC addressmac-addr
Command Mode
• /exec/configure/if-igp /exec/configure/if-mgmt-config /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2396
I Commandsipv6 neighbor
Page 2541
ipv6 neighbor allow-static-neighbor-outside-subnet[no] ipv6 neighbor allow-static-neighbor-outside-subnet
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure IPv6 address to layer-2 address mappingneighbor
Allow static neighbor outside interface subnetallow-static-neighbor-outside-subnet
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2397
I Commandsipv6 neighbor allow-static-neighbor-outside-subnet
Page 2542
ipv6 neighbor binding[no] ipv6 neighbor binding { { reachable-lifetime { infinite | <reach-secs> } } | { stale-lifetime { infinite |<stale-secs> } } | { down-lifetime { infinite | <down-secs> } } } +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Secondsreach-secs
Secondsstale-secs
Secondsdown-secs
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2398
I Commandsipv6 neighbor binding
Page 2543
ipv6 neighbor binding[no] ipv6 neighbor binding { { vlan <vlanid> { <ipv6addr1> } } interface <intf> [ <mac-address> [ tracking{ default | disable | enable [ retry-interval { default | <interval> } ] } ] [ reachable-lifetime { default | infinite| <reach-secs> } ] ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Number of entriesvlanid
Interfaceintf
(Optional) 48-bit hardware address / <cr> for any mac addressmac-address
(Optional) secondsinterval
(Optional) secondsreach-secs
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2399
I Commandsipv6 neighbor binding
Page 2544
ipv6 neighbor binding logging[no] ipv6 neighbor binding logging
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2400
I Commandsipv6 neighbor binding logging
Page 2545
ipv6 neighbor binding max-entries{ ipv6 neighbor binding max-entries <box-lim> { [ vlan-limit <vlan-lim> ] | [ port-limit <port-lim> ] | [mac-limit <mac-lim> ] } + | no ipv6 neighbor binding max-entries [ <box-lim> { [ vlan-limit <vlan-lim> ] |[ port-limit <port-lim> ] | [ mac-limit <mac-lim> ] } + ] }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Number of entriesbox-lim
(Optional) Number of entriesvlan-lim
(Optional) Number of entriesport-lim
(Optional) Number of entriesmac-lim
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2401
I Commandsipv6 neighbor binding max-entries
Page 2546
ipv6 neighbor tracking[no] ipv6 neighbor tracking [ retry-interval <interval> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) Secondsinterval
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2402
I Commandsipv6 neighbor tracking
Page 2547
ipv6 pim anycast-rp[no] ipv6 pim anycast-rp <anycast-rp> <rp-addr>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Configure an RP in an Anycast-RP set (using PIM6)anycast-rp
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2403
I Commandsipv6 pim anycast-rp
Page 2548
ipv6 pim bidir-rp-limit[no] ipv6 pim bidir-rp-limit <limit>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Configures maximum Bidir RPs for IPv6 PIM in this VRFbidir-rp-limit
Set limit for Bidir RPs permitted in IPv6 PIMlimit
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2404
I Commandsipv6 pim bidir-rp-limit
Page 2549
ipv6 pim border[no] ipv6 pim border
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 interface configuration commandspim
Configures interface to be a boundary of a PIM6 domainborder
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2405
I Commandsipv6 pim border
Page 2550
ipv6 pim bsr-candidate{ { ipv6 pim [ bsr ] bsr-candidate <interface> [ hash-len <hash-len> ] [ priority <priority> ] } | { no ipv6 pim[ bsr ] bsr-candidate [ <interface> ] [ hash-len <hash-len> ] [ priority <priority> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
(Optional) Bootstrap protocol RP-distribution configurationbsr
Configure router as a Bootstrap Router candidatebsr-candidate
Use IPV6 address of interface for Bootstrap messagesinterface
(Optional) Hash mask length used in Bootstrap messageshash-len
(Optional) Hash mask length valuehash-len
(Optional) BSR priority used in Bootstrap messagespriority
(Optional) BSR priority valuepriority
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2406
I Commandsipv6 pim bsr-candidate
Page 2551
ipv6 pim bsr bsr-policy{ ipv6 pim bsr bsr-policy { <route-map-name> | <rtr_pol_name> } | no ipv6 pim bsr bsr-policy [<route-map-name> | <rtr_pol_name> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Bootstrap protocol RP-distribution configurationbsr
Specify policy for filtering BSR messagesbsr-policy
A route-map nameroute-map-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2407
I Commandsipv6 pim bsr bsr-policy
Page 2552
ipv6 pim bsr listen{ ipv6 pim bsr { listen | forward } + } | { no ipv6 pim bsr [ { listen | forward } + ] }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Bootstrap protocol RP-distribution configurationbsr
Listen to Bootstrap/Candidate-RP messageslisten
Forward Bootstrap/Candidate-RP messagesforward
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2408
I Commandsipv6 pim bsr listen
Page 2553
ipv6 pim bsr rp-candidate-policy{ ipv6 pim bsr rp-candidate-policy { <route-map-name> | <rtr_pol_name> } | no ipv6 pim bsrrp-candidate-policy [ <route-map-name> | <rtr_pol_name> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Bootstrap protocol RP-distribution configurationbsr
Specify policy for filtering RP candidate messagesrp-candidate-policy
A route-map nameroute-map-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2409
I Commandsipv6 pim bsr rp-candidate-policy
Page 2554
ipv6 pim dr-priority{ { ipv6 pim dr-priority <priority> } | { no ipv6 pim dr-priority [ <priority> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 interface configuration commandspim
Configures priority for PIM6 DR election on interfacedr-priority
Priority valuepriority
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2410
I Commandsipv6 pim dr-priority
Page 2555
ipv6 pim event-history assert-receive[no] ipv6 pim event-history assert-receive { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Configure event-history bufferevent-history
Assert-receive events for PIM6assert-receive
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2411
I Commandsipv6 pim event-history assert-receive
Page 2556
ipv6 pim event-history bidir[no] ipv6 pim event-history bidir { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Configure event-history bufferevent-history
Bidir events for PIM6bidir
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2412
I Commandsipv6 pim event-history bidir
Page 2557
ipv6 pim event-history hello[no] ipv6 pim event-history hello { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Configure event-history bufferevent-history
Hello events for PIM6hello
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2413
I Commandsipv6 pim event-history hello
Page 2558
ipv6 pim event-history join-prune[no] ipv6 pim event-history join-prune { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Configure event-history bufferevent-history
Join/Prune events for PIM6join-prune
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2414
I Commandsipv6 pim event-history join-prune
Page 2559
ipv6 pim event-history null-register[no] ipv6 pim event-history null-register { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Configure event-history bufferevent-history
Reg events for PIM6null-register
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2415
I Commandsipv6 pim event-history null-register
Page 2560
ipv6 pim event-history packet[no] ipv6 pim event-history packet { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Configure event-history bufferevent-history
Packet events for PIM6packet
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2416
I Commandsipv6 pim event-history packet
Page 2561
ipv6 pim event-history rp[no] ipv6 pim event-history rp { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Configure event-history bufferevent-history
RP events for PIM6rp
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2417
I Commandsipv6 pim event-history rp
Page 2562
ipv6 pim event-history vrf[no] ipv6 pim event-history vrf { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Configure event-history bufferevent-history
VRF events for PIM6vrf
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2418
I Commandsipv6 pim event-history vrf
Page 2563
ipv6 pim flush-routes[no] ipv6 pim flush-routes
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Remove routes when restarting PIM6flush-routes
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2419
I Commandsipv6 pim flush-routes
Page 2564
ipv6 pim hello-interval{ { ipv6 pim hello-interval { <interval-min> | <interval-max> } } | { no ipv6 pim hello-interval [ <interval-min>| <interval-max> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 interface configuration commandspim
Configures the Hello interval for interfacehello-interval
Interval in millisecondsinterval-min
Interval in millisecondsinterval-max
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2420
I Commandsipv6 pim hello-interval
Page 2565
ipv6 pim isolate[no] ipv6 pim isolate
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Isolate this router from IPV6 PIM perspectiveisolate
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2421
I Commandsipv6 pim isolate
Page 2566
ipv6 pim jp-policy{ ipv6 pim jp-policy { <route-map-name> | <rtr_pol_name> } [ in | out ] | no ipv6 pim jp-policy [<route-map-name> | <rtr_pol_name> ] [ in | out ] }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 interface configuration commandspim
Specify policy for receiving Join-Prune messagesjp-policy
A route-map nameroute-map-name
An existing routing-rules policyrtr_pol_name
(Optional) Inboundin
(Optional) Outboundout
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2422
I Commandsipv6 pim jp-policy
Page 2567
ipv6 pim log-neighbor-changes[no] ipv6 pim log-neighbor-changes
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Log up/down PIM6 neighbor transitionslog-neighbor-changes
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2423
I Commandsipv6 pim log-neighbor-changes
Page 2568
ipv6 pim neighbor-policy{ ipv6 pim neighbor-policy <route-map-name> | no ipv6 pim neighbor-policy [ <route-map-name> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 interface configuration commandspim
Configures a neighbor policy for filtering adjacenciesneighbor-policy
A route-map nameroute-map-name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2424
I Commandsipv6 pim neighbor-policy
Page 2569
ipv6 pim passive[no] ipv6 pim passive
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 interface configuration commandspim
Interface in passive mode. No send/recvpassive
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2425
I Commandsipv6 pim passive
Page 2570
ipv6 pim register-policy{ ipv6 pim register-policy { <route-map-name> | <rtr_pol_name> } | no ipv6 pim register-policy [<route-map-name> | <rtr_pol_name> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Specify policy for receiving Register messagesregister-policy
A route-map nameroute-map-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2426
I Commandsipv6 pim register-policy
Page 2571
ipv6 pim register-rate-limit{ { ipv6 pim register-rate-limit <rate> } | { no ipv6 pim register-rate-limit [ <rate> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Rate limit for PIM data registersregister-rate-limit
Packets per secondrate
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2427
I Commandsipv6 pim register-rate-limit
Page 2572
ipv6 pim rp-address{ { ipv6 pim rp-address <rp-address> [ group-list <prefix> | route-map <route-map-name> | prefix-list<prefix-list-name> ] [ bidir ] [ override ] } | { no ipv6 pim rp-address <rp-address> [ group-list <prefix> |route-map <route-map-name> | prefix-list <prefix-list-name> ] [ bidir ] [ override ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Configure static RP for group rangerp-address
(Optional) Group range for static RPgroup-list
(Optional) Route Map policy for static RProute-map
(Optional) route-map nameroute-map-name
(Optional) Prefix List policy for static RPprefix-list
(Optional) prefix-list nameprefix-list-name
(Optional) Group range is treated in PIM6 bidirectional modebidir
(Optional) Overrides the dynamically learnt RPsoverride
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2428
I Commandsipv6 pim rp-address
Page 2573
ipv6 pim rp-candidate group{ { ipv6 pim [ bsr ] rp-candidate <interface> { group-list <prefix> | route-map <route-map-name> } [ priority<priority> ] [ interval <interval> ] [ bidir ] } | { no ipv6 pim [ bsr ] rp-candidate [ <interface> ] [ group-list<prefix> ] [ route-map <route-map-name> ] [ priority <priority> ] [ interval <interval> ] [ bidir ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
(Optional) Bootstrap protocol RP-distribution configurationbsr
Configure router as a Rendezvous Point (RP) candidaterp-candidate
IPV6 address of interface for Candidate-RP messagesinterface
Group range listgroup-list
Group range policy for Candidate RProute-map
route-map nameroute-map-name
(Optional) RP priority used in Candidate-RP messagespriority
(Optional) RP priority valuepriority
(Optional) Bootstrap message transmission intervalinterval
(Optional) Interval in secondsinterval
(Optional) Group range advertised in PIM6 bidirectional modebidir
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2429
I Commandsipv6 pim rp-candidate group
Page 2574
ipv6 pim sparse-modeipv6 pim sparse-mode | no ipv6 pim [ sparse-mode ]
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 interface configuration commandspim
Configures sparse-mode PIMv6 on interfacesparse-mode
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2430
I Commandsipv6 pim sparse-mode
Page 2575
ipv6 pim ssm{ ipv6 pim ssm { { range { <group> + | none } } | { route-map <route-map-name> } } | no ipv6 pim ssm { {range { <group> + | none } } | { route-map <route-map-name> } } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Source Specific Multicast (SSM) groupsssm
Configure explicit group rangesrange
Remove all SSM group rangesnone
Group range policy for SSM rangeroute-map
A route-map nameroute-map-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2431
I Commandsipv6 pim ssm
Page 2576
ipv6 pim state-limit{ { ipv6 pim state-limit <max-states> [ reserved <route-map-name> <max-reserved> ] } | { no ipv6 pimstate-limit [ <max-states> [ reserved <route-map-name> <max-reserved> ] ] } }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Configures State limitstate-limit
Maximum (*,G)/(S,G) entries allowed in this VRFmax-states
(Optional) Configures Reserved limitreserved
(Optional) Route-map nameroute-map-name
(Optional) Maximum reserved (*,G)/(S,G) entries allowed in this VRFmax-reserved
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2432
I Commandsipv6 pim state-limit
Page 2577
ipv6 pim use-shared-tree-only spt-threshold infinity group-list{ ipv6 pim { use-shared-tree-only | spt-threshold infinity } group-list <route-map-name> } | { no ipv6 pim {use-shared-tree-only | spt-threshold infinity } [ group-list <route-map-name> ] }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
PIM6 global configuration commandspim
Use (*,G) only state, no source state is createduse-shared-tree-only
Source-tree switching thresholdspt-threshold
Never switch to source-treeinfinity
Specify group ranges through policygroup-list
Route-map nameroute-map-name
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2433
I Commandsipv6 pim use-shared-tree-only spt-threshold infinity group-list
Page 2578
ipv6 policy route-mapipv6 policy route-map <route-map-name> | no ipv6 policy route-map [ <route-map-name> | <route-map-name>]
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure PBR featurepolicy
Route-map for PBRroute-map
Route-map nameroute-map-name
(Optional) Route-map nameroute-map-name
(Optional) Known route-map nameroute-map-name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2434
I Commandsipv6 policy route-map
Page 2579
ipv6 port traffic-filter[no] ipv6 port traffic-filter <name> <inout>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Port policyport
Specify access control for packetstraffic-filter
List namename
Traffic directioninout
Command Mode
• /exec/configure/if-set-acl-l2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2435
I Commandsipv6 port traffic-filter
Page 2580
ipv6 prefix-list description{ ipv6 prefix-list <ipv6-pfl-name> description <line> } | { no ipv6 prefix-list <ipv6-pfl-name> description }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Build a prefix listprefix-list
Name of prefix-listipv6-pfl-name
Known prefix-list nameipv6-pfl-name
Description of the IPv6 prefix listdescription
IPv6 prefix-list description stringline
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2436
I Commandsipv6 prefix-list description
Page 2581
ipv6 prefix-list permit{ ipv6 prefix-list <ipv6-pfl-name> [ seq <seq> ] { permit | deny } <prefix> { [ eq <equal> ] | [ ge <greater>] [ le <lesser> ] } } | { no ipv6 prefix-list { <ipv6-pfl-name> | <ipv6-pfl-name> } [ seq <seq> ] [ { permit |deny } <prefix> { [ eq <equal> ] | [ ge <greater> ] [ le <lesser> ] } ] }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Build a prefix listprefix-list
Name of prefix-listipv6-pfl-name
Name of prefix-listipv6-pfl-name
Known prefix-list nameipv6-pfl-name
(Optional) Sequence number of an entryseq
(Optional) Sequence numberseq
Specify routes to forwardpermit
Specify routes to rejectdeny
(Optional) Exact prefix length to be matchedeq
(Optional) Exact prefix lengthequal
(Optional) Minimum prefix length to be matchedge
(Optional) Minimum prefix lengthgreater
(Optional) Maximum prefix length to be matchedle
(Optional) Maximum prefix lengthlesser
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2437
I Commandsipv6 prefix-list permit
Page 2582
ipv6 queue-packets[no] ipv6 queue-packets
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Queue 1 packet when triggered NS is sentqueue-packets
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2438
I Commandsipv6 queue-packets
Page 2583
ipv6 redirectsipv6 [ nd ] redirects | no ipv6 [ nd ] redirects
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 Neighbor Discovery commandsnd
Enable sending ICMPv6 Redirect messagesredirects
Command Mode
• /exec/configure/if-igp /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2439
I Commandsipv6 redirects
Page 2584
ipv6 route[no] ipv6 route <ipv6-prefix> { <interface> | { { <link-local> <interface-link-local> } | { <pin-interface><next-hop> } | { <next-hop> | <nh-prefix> } | { <vlan-interface> } } [ vrf { <vrf-name> | <vrf-known-name>} ] } [ track <object-num> ] [ name <rt-name> ] [ <pref> | tag <tag-value> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Configure IPv6 unicast static routeroute
Interface for interface static routesinterface
vlan interfacevlan-interface
(Optional) Specify name of the next hopname
(Optional) Name of next hoprt-name
Pin interfacepin-interface
Interface for interface static routesinterface-link-local
(Optional) Specify the Object to be Trackedtrack
(Optional) Track Object Numberobject-num
(Optional) VRF for next-hop if different from this vrfvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Route preferencepref
(Optional) Supply tag value with static routetag
(Optional) 32-bit value for tagtag-value
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2440
I Commandsipv6 route
Page 2585
ipv6 route static bfd[no] ipv6 route static bfd <pin-interface> <next-hop>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IP featuresipv6
Route informationroute
Static route based configurationstatic
Enable bfd detection on static routebfd
Interface on which bfd has to be enabledpin-interface
Command Mode
• /exec/configure /exec/configure/config-mgmt /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2441
I Commandsipv6 route static bfd
Page 2586
ipv6 router isis[no] ipv6 router isis <tag>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Enable a routing processrouter
Intermediate System to Intermediate System (IS-IS)isis
Process tagtag
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2442
I Commandsipv6 router isis
Page 2587
ipv6 router ospfv3 area[no] ipv6 router ospfv3 <tag> area { <area-id-ip> | <area-id-int> } [ secondaries none ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Enable a routing processrouter
OSPFv3 configuration commandsospfv3
Process tagtag
Area associated with interfacearea
OSPFv3 area ID in IP address formatarea-id-ip
OSPFv3 area ID as a decimal formatarea-id-int
(Optional) Do not include secondary IPv6 addressessecondaries
(Optional) Do not include secondary IPv6 addressesnone
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2443
I Commandsipv6 router ospfv3 area
Page 2588
ipv6 router ospfv3 multi-area[no] ipv6 router ospfv3 [ <tag> ] multi-area <area-id-ip>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Enable a routing processrouter
OSPFv3 configuration commandsospfv3
(Optional) Process tagtag
Multi-Area associated with interfacemulti-area
Area Id as an integer or ip addressarea-id-ip
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2444
I Commandsipv6 router ospfv3 multi-area
Page 2589
ipv6 routing event-history size[no] ipv6 routing event-history { am | cli | detail | errors | general | ha | lfe | recursive-next-hop | summary |ufdm | ufdm-detail | ufdm-summary } size { <size_in_text> | <size_in_bytes> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Routing informationrouting
Configure routing event logevent-history
AMam
CLIcli
Detaildetail
Errorserrors
Generalgeneral
HAha
LFElfe
Recursive next hoprecursive-next-hop
Summarysummary
UFDMufdm
UFDM Detailufdm-detail
UFDM Summaryufdm-summary
Size of buffersize
Buffer sizesize_in_text
Enter an integer value for the event history buffersize_in_bytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2445
I Commandsipv6 routing event-history size
Page 2590
ipv6 routing multicast event-history cli[no] ipv6 routing multicast event-history cli { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Routing informationrouting
Configure multicastmulticast
Configure event history buffersevent-history
CLI events for MRIBcli
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2446
I Commandsipv6 routing multicast event-history cli
Page 2591
ipv6 routing multicast event-history mfdm-debugs[no] ipv6 routing multicast event-history mfdm-debugs { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Routing informationrouting
Configure multicastmulticast
Configure event history buffersevent-history
MFDM events for MRIBmfdm-debugs
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2447
I Commandsipv6 routing multicast event-history mfdm-debugs
Page 2592
ipv6 routing multicast event-history mfdm-events[no] ipv6 routing multicast event-history mfdm-events { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Routing informationrouting
Configure multicastmulticast
Configure event history buffersevent-history
Non-periodic MFDM events in MRIBmfdm-events
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2448
I Commandsipv6 routing multicast event-history mfdm-events
Page 2593
ipv6 routing multicast event-history mfdm-stats[no] ipv6 routing multicast event-history mfdm-stats { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Routing informationrouting
Configure multicastmulticast
Configure event history buffersevent-history
MFDM-stats events for MRIBmfdm-stats
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2449
I Commandsipv6 routing multicast event-history mfdm-stats
Page 2594
ipv6 routing multicast event-history rib-summary[no] ipv6 routing multicast event-history rib-summary { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Routing informationrouting
Configure multicastmulticast
Configure event-history buffersevent-history
RIB events for MRIB-summaryrib-summary
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2450
I Commandsipv6 routing multicast event-history rib-summary
Page 2595
ipv6 routing multicast event-history rib[no] ipv6 routing multicast event-history rib { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Routing informationrouting
Configure multicastmulticast
Configure event history buffersevent-history
RIB events for MRIBrib
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2451
I Commandsipv6 routing multicast event-history rib
Page 2596
ipv6 routing multicast event-history vrf[no] ipv6 routing multicast event-history vrf { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Routing informationrouting
Configure multicastmulticast
Configure event history buffersevent-history
VRF events for MRIBvrf
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2452
I Commandsipv6 routing multicast event-history vrf
Page 2597
ipv6 routing multicast holddownipv6 routing multicast holddown { <route-holddown-sec> | <none> } | no ipv6 routing multicast holddown [<route-holddown-sec> | <none> ]
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Routing informationrouting
Configure multicastmulticast
Initial holddown periodholddown
Delay in secondsroute-holddown-sec
Disable holddownnone
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2453
I Commandsipv6 routing multicast holddown
Page 2598
ipv6 routing multicast software-replication[no] ipv6 routing multicast software-replication
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Routing informationrouting
Configure multicastmulticast
Enable software replication of PIM ASM leak packetssoftware-replication
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2454
I Commandsipv6 routing multicast software-replication
Page 2599
ipv6 snooping[no] ipv6 snooping [ attach-policy <policy_name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) policy name for ipv6 snoopingpolicy_name
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2455
I Commandsipv6 snooping
Page 2600
ipv6 snooping[no] ipv6 snooping [ attach-policy <policy_name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) policy name for ipv6 snoopingpolicy_name
Command Mode
• /exec/configure/vlan-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2456
I Commandsipv6 snooping
Page 2601
ipv6 snooping policy[no] ipv6 snooping policy <name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Name of the snooping policyname
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2457
I Commandsipv6 snooping policy
Page 2602
ipv6 switch-packets[no] ipv6 switch-packets [ lla ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Switch ND packets received on core portsswitch-packets
(Optional) Switch ND packets targeted to Link local address on coreports
lla
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2458
I Commandsipv6 switch-packets
Page 2603
ipv6 traffic-filter[no] ipv6 traffic-filter <name> <inout>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Specify access control for packetstraffic-filter
List namename
Traffic directioninout
Command Mode
• /exec/configure/if-set-acl-l3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2459
I Commandsipv6 traffic-filter
Page 2604
ipv6 unreachables[no] ipv6 [ icmp ] unreachables
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IPv6 featuresipv6
(Optional) ICMPv6 commandsicmp
Enable sending ICMPv6 Unreachable messages (port-unreachables arealways rate-limit enabled)
unreachables
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2460
I Commandsipv6 unreachables
Page 2605
ipv6 verify unicast source reachable-via rx[no] ipv6 verify unicast source reachable-via [ { rx | any [ allow-default ] } ] | ipv6 verify unicast sourcereachable-via { rx | any [ allow-default ] }
Syntax Description
Negate a command or set its defaultsno
Configure IPv6 featuresipv6
Unicast Reverse Path Forwardingverify
Unicast Reverse Path Forwardingunicast
Validation of source addresssource
Specify reachability check to apply to the source addressreachable-via
(Optional) Source is reachable via interface on which packet wasreceived
rx
(Optional) Source is reachable via any interfaceany
(Optional) Loose Default Route Unicast Reverse Path Forwardingallow-default
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2461
I Commandsipv6 verify unicast source reachable-via rx
Page 2606
is-typeis-type <is-type> | no is-type [ <is-type> ]
Syntax Description
Negate a command or set its defaultsno
IS type for this IS-IS processis-type
IS-IS IS typeis-type
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2462
I Commandsis-type
Page 2607
ishow cli find nodesishow cli find nodes [ <component> ] [ recurse ]
Syntax Description
Show internal informationishow
Show CLI informationcli
find
displaynodes
(Optional) displaycomponent
(Optional) gorecurse
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2463
I Commandsishow cli find nodes
Page 2608
ishow cli modesishow cli modes
Syntax Description
Show internal informationishow
Show CLI informationcli
showmodes
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2464
I Commandsishow cli modes
Page 2609
ishow cli nodesishow cli nodes [ <mode> ]
Syntax Description
Show internal informationishow
Show CLI informationcli
shownodes
(Optional) modemode
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2465
I Commandsishow cli nodes
Page 2610
ishow cli pathsishow cli paths <component> [ <type> ]
Syntax Description
Show internal informationishow
Show CLI informationcli
showpaths
componentcomponent
(Optional)type
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2466
I Commandsishow cli paths
Page 2611
ishow cli tagsishow cli tags
Syntax Description
Show internal informationishow
Show CLI informationcli
tags
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2467
I Commandsishow cli tags
Page 2612
ishow core backtraceishow core <pid> backtrace
Syntax Description
Show internal informationishow
display info from core filecore
PID from 'show corespid
display backtrace -- needs enough space to unzip the core file!backtrace
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2468
I Commandsishow core backtrace
Page 2613
isis authentication-check[no] isis authentication-check
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Check authentication on received hellosauthentication-check
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2469
I Commandsisis authentication-check
Page 2614
isis authentication-check level-1[no] isis authentication-check level-1
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Check authentication on received hellosauthentication-check
Configure authentication check for level-1 IIHslevel-1
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2470
I Commandsisis authentication-check level-1
Page 2615
isis authentication-check level-2[no] isis authentication-check level-2
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Check authentication on received hellosauthentication-check
Configure authentication check for level-2 IIHslevel-2
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2471
I Commandsisis authentication-check level-2
Page 2616
isis authentication-type cleartext{ isis authentication-type { cleartext | md5 } <level> | no isis authentication-type [ { cleartext | md5 } ] <level>}
Syntax Description
Negate a command or set its defaultsno
IS-IS configuration commandsisis
Set hello authentication typeauthentication-type
Cleartextcleartext
HMAC-MD5md5
IS-IS levellevel
Command Mode
• /exec/configure/if-ma
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2472
I Commandsisis authentication-type cleartext
Page 2617
isis authentication-type cleartext{ isis authentication-type { cleartext | md5 } | no isis authentication-type [ { cleartext | md5 } ] }
Syntax Description
Negate a command or set its defaultsno
IS-IS configuration commandsisis
Set hello authentication typeauthentication-type
Cleartextcleartext
HMAC-MD5md5
Command Mode
• /exec/configure/if-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2473
I Commandsisis authentication-type cleartext
Page 2618
isis authentication key-chain{ isis authentication key-chain <auth-keychain> <level> | no isis authentication key-chain [ <auth-keychain>] <level> }
Syntax Description
Negate a command or set its defaultsno
IS-IS configuration commandsisis
Set hello authentication keychainauthentication
Set hello authentication keychainkey-chain
authentication keychainauth-keychain
IS-IS levellevel
Command Mode
• /exec/configure/if-ma
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2474
I Commandsisis authentication key-chain
Page 2619
isis authentication key-chain{ isis authentication key-chain <auth-keychain> | no isis authentication key-chain [ <auth-keychain> ] }
Syntax Description
Negate a command or set its defaultsno
IS-IS configuration commandsisis
Set hello authentication keychainauthentication
Set hello authentication keychainkey-chain
authentication keychainauth-keychain
Command Mode
• /exec/configure/if-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2475
I Commandsisis authentication key-chain
Page 2620
isis bfd[no] isis bfd [ disable ]
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Interface BFD configurationbfd
(Optional) Disable BFD on interfacedisable
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2476
I Commandsisis bfd
Page 2621
isis circuit-typeisis circuit-type <circuit-type> | no isis circuit-type [ <circuit-type> ]
Syntax Description
Negate a command or set its defaultsno
IS-IS configuration commandsisis
Configure circuit type for interfacecircuit-type
IS-IS circuit typecircuit-type
isis
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2477
I Commandsisis circuit-type
Page 2622
isis csnp-interval level[no] isis csnp-interval <sec> { level-1 | level-2 }
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Set CSNP interval in secondscsnp-interval
CSNP interval valuesec
Specify interval for level-1 CSNPslevel-1
Specify interval for level-2 CSNPslevel-2
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2478
I Commandsisis csnp-interval level
Page 2623
isis event-history adjacency[no] isis event-history adjacency { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
Adjacency events for IS-ISadjacency
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2479
I Commandsisis event-history adjacency
Page 2624
isis event-history cli[no] isis event-history cli { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
CLI events for IS-IScli
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2480
I Commandsisis event-history cli
Page 2625
isis event-history csnp[no] isis event-history csnp { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
CSNP events for IS-IScsnp
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2481
I Commandsisis event-history csnp
Page 2626
isis event-history dis[no] isis event-history dis { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
Dis events for IS-ISdis
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2482
I Commandsisis event-history dis
Page 2627
isis event-history events[no] isis event-history events { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
Events for IS-ISevents
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2483
I Commandsisis event-history events
Page 2628
isis event-history graceful[no] isis event-history graceful { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
Graceful Restart events for IS-ISgraceful
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2484
I Commandsisis event-history graceful
Page 2629
isis event-history ha[no] isis event-history ha { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
HA events for IS-ISha
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2485
I Commandsisis event-history ha
Page 2630
isis event-history iih[no] isis event-history iih { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
IIH events for IS-ISiih
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2486
I Commandsisis event-history iih
Page 2631
isis event-history lsp-flood[no] isis event-history lsp-flood { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
LSP-flood events for IS-ISlsp-flood
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2487
I Commandsisis event-history lsp-flood
Page 2632
isis event-history lsp-gen[no] isis event-history lsp-gen { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
LSP-Gen events for IS-ISlsp-gen
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2488
I Commandsisis event-history lsp-gen
Page 2633
isis event-history mtr[no] isis event-history mtr { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
MTR events for IS-ISmtr
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2489
I Commandsisis event-history mtr
Page 2634
isis event-history perf[no] isis event-history perf { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
Performance events for IS-ISperf
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2490
I Commandsisis event-history perf
Page 2635
isis event-history psnp[no] isis event-history psnp { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
PSNP events for IS-ISpsnp
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2491
I Commandsisis event-history psnp
Page 2636
isis event-history redist[no] isis event-history redist { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
Redist events for IS-ISredist
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2492
I Commandsisis event-history redist
Page 2637
isis event-history spf-leaf[no] isis event-history spf-leaf { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
Shortest path first events for IS-ISspf-leaf
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2493
I Commandsisis event-history spf-leaf
Page 2638
isis event-history spf-tree[no] isis event-history spf-tree { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
SPF-Tree events for IS-ISspf-tree
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2494
I Commandsisis event-history spf-tree
Page 2639
isis event-history sr[no] isis event-history sr { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
SR events for IS-ISsr
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2495
I Commandsisis event-history sr
Page 2640
isis event-history tlv[no] isis event-history tlv { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
TLV events for IS-IStlv
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2496
I Commandsisis event-history tlv
Page 2641
isis event-history ulib[no] isis event-history ulib { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
ULIB events for IS-ISulib
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2497
I Commandsisis event-history ulib
Page 2642
isis event-history urib[no] isis event-history urib { size { <size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Event-history buffers for IS-ISisis
Configure event-history buffersevent-history
URIB events for IS-ISurib
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2498
I Commandsisis event-history urib
Page 2643
isis hello-interval[no] isis hello-interval <sec>
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Set Hello interval in secondshello-interval
Hello interval valuesec
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2499
I Commandsisis hello-interval
Page 2644
isis hello-interval level[no] isis hello-interval <sec> { level-1 | level-2 }
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Set Hello interval in secondshello-interval
Hello interval valuesec
Specify hello-interval for level-1 IIHslevel-1
Specify hello-interval for level-2 IIHslevel-2
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2500
I Commandsisis hello-interval level
Page 2645
isis hello-multiplier[no] isis hello-multiplier <multi>
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Set multiplier for Hello holding timehello-multiplier
Hello multiplier valuemulti
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2501
I Commandsisis hello-multiplier
Page 2646
isis hello-multiplier level[no] isis hello-multiplier <multi> { level-1 | level-2 }
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Set multiplier for Hello holding timehello-multiplier
Hello multiplier valuemulti
Specify hello multiplier for level-1 IIHslevel-1
Specify hello multiplier for level-2 IIHslevel-2
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2502
I Commandsisis hello-multiplier level
Page 2647
isis hello-padding{ isis hello-padding | no isis hello-padding [ always ] }
Syntax Description
Negate a command or set its defaultsno
IS-IS configuration commandsisis
Pad IS-IS hello PDUs to full MTUhello-padding
(Optional) Pad every helloalways
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2503
I Commandsisis hello-padding
Page 2648
isis ipv6 bfd[no] isis ipv6 bfd [ disable ]
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Enable BFD for ipv6ipv6
Interface BFD configurationbfd
(Optional) Disable BFD on interfacedisable
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2504
I Commandsisis ipv6 bfd
Page 2649
isis ipv6 metric[no] isis ipv6 metric <metric> <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Configure metric for IPV6 topologymetric
Configure metric for IPV6 topologyipv6
Default metricmetric
IS-IS levellevel
Command Mode
• /exec/configure/if-igp /exec/configure/router-isis/router-isis-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2505
I Commandsisis ipv6 metric
Page 2650
isis lsp-interval[no] isis lsp-interval <msec>
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Set LSP transmission intervallsp-interval
LSP transmission interval (milliseconds)msec
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2506
I Commandsisis lsp-interval
Page 2651
isis mesh-group{ isis mesh-group { blocked | <mesh-id> } | no isis mesh-group [ { blocked | <mesh-id> } ] }
Syntax Description
Negate a command or set its defaultsno
IS-IS configuration commandsisis
Set IS-IS mesh groupmesh-group
Mesh group numbermesh-id
Block LSPs on this interfaceblocked
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2507
I Commandsisis mesh-group
Page 2652
isis metric[no] isis metric <metric> <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Configure the metric for interfacemetric
Default metricmetric
IS-IS levellevel
Command Mode
• /exec/configure/if-igp /exec/configure/if-mpls-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2508
I Commandsisis metric
Page 2653
isis mtu-check[no] isis mtu-check
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Check mtu on received hellos, if its paddedmtu-check
Command Mode
• /exec/configure/if-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2509
I Commandsisis mtu-check
Page 2654
isis mtu-check level[no] isis mtu-check { level-1 | level-2 }
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Check mtu on received hellos, if its paddedmtu-check
Configure mtu-check for level-1level-1
Configure mtu-check for level-2level-2
Command Mode
• /exec/configure/if-ma
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2510
I Commandsisis mtu-check level
Page 2655
isis network point-to-point[no] isis network point-to-point [ use-allIS-mac ]
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Change interface medium to p2pnetwork
Change interface medium to p2ppoint-to-point
(Optional) use allISs MAC for Tx packetsuse-allIS-mac
Command Mode
• /exec/configure/if-igp /exec/configure/if-mpls-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2511
I Commandsisis network point-to-point
Page 2656
isis passive-interfaceisis passive-interface <level> | no isis passive-interface <level> | default isis passive-interface [ <level_obsolete>]
Syntax Description
Negate a command or set its defaultsno
IS-IS configuration commandsisis
Suppress IS-IS PDUpassive-interface
Undo a commanddefault
Level to suppresslevel
(Optional) Level to suppresslevel_obsolete
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2512
I Commandsisis passive-interface
Page 2657
isis prefix-attributes n-flag-clear[no] isis prefix-attributes n-flag-clear
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Segment routing attributeprefix-attributes
Clear N flag for prefixn-flag-clear
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2513
I Commandsisis prefix-attributes n-flag-clear
Page 2658
isis priority level[no] isis priority <priority> { level-1 | level-2 }
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Set priority for DIS electionpriority
Priority valuepriority
Specify priority for level-1 routinglevel-1
Specify priority for level-2 routinglevel-2
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2514
I Commandsisis priority level
Page 2659
isis retransmit-interval[no] isis retransmit-interval <sec>
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Set per-LSP retransmission intervalretransmit-interval
Interval between retransmissions of the same LSP (seconds)sec
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2515
I Commandsisis retransmit-interval
Page 2660
isis retransmit-throttle-interval[no] isis retransmit-throttle-interval <msec>
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Set interface LSP retransmission intervalretransmit-throttle-interval
Delay between retransmitted LSPs (milliseconds)msec
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2516
I Commandsisis retransmit-throttle-interval
Page 2661
isis shutdown[no] isis shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
IS-IS configuration commandsisis
Graceful shutdown IS-IS functionality on the interfaceshutdown
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2517
I Commandsisis shutdown
Page 2662
isolate[no] isolate
Syntax Description
(Optional) Negate a command or set its defaultsno
Isolate this router from RIP perspectiveisolate
Command Mode
• /exec/configure/router-rip
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2518
I Commandsisolate
Page 2663
isolate[no] isolate
Syntax Description
(Optional) Negate a command or set its defaultsno
Isolate router, ISIS perspective (set overload)isolate
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2519
I Commandsisolate
Page 2664
isolate[no] isolate
Syntax Description
(Optional) Negate a command or set its defaultsno
Isolate this router from OSPFV3 perspectiveisolate
Command Mode
• /exec/configure/router-ospf3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2520
I Commandsisolate
Page 2665
isolate[no] isolate
Syntax Description
(Optional) Negate a command or set its defaultsno
Isolate this router from EIGRP perspectiveisolate
Command Mode
• /exec/configure/router-eigrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2521
I Commandsisolate
Page 2666
isolate[no] isolate
Syntax Description
(Optional) Negate a command or set its defaultsno
Isolate this router from OSPF perspectiveisolate
Command Mode
• /exec/configure/router-ospf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2522
I Commandsisolate
Page 2667
isolate[no] isolate
Syntax Description
(Optional) Negate a command or set its defaultsno
Isolate this router from BGP perspectiveisolate
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2523
I Commandsisolate
Page 2668
isolate[no] isolate
Syntax Description
(Optional) Negate a command or set its defaultsno
Isolate fabric spine (set overload)isolate
Command Mode
• /exec/configure/l2mp-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2524
I Commandsisolate
Page 2669
itd{ itd <service-name> } | { no itd <service-name> }
Syntax Description
Negate a command or set its defaultsno
ITD serviceitd
ITD service-nameservice-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2525
I Commandsitd
Page 2670
itd device-group{ itd device-group <svc-name> } | { no itd device-group <svc-name> }
Syntax Description
Negate a command or set its defaultsno
ITD serviceitd
ITD device groupdevice-group
service-namesvc-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2526
I Commandsitd device-group
Page 2671
itd session access-list refreshitd session access-list <acl-name> refresh
Syntax Description
ITD serviceitd
ITD sessionsession
ITD include access-listaccess-list
acl-nameacl-name
Refresh ITD policies based on access-list changesrefresh
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2527
I Commandsitd session access-list refresh
Page 2672
itd session device-group{ itd session device-group <svc-name> } | { no itd session device-group <svc-name> }
Syntax Description
Negate a command or set its defaultsno
ITD serviceitd
ITD sessionsession
ITD device groupdevice-group
service-namesvc-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2528
I Commandsitd session device-group
Page 2673
itd statistics{ itd statistics <service-name> } | { no itd statistics <service-name> }
Syntax Description
Negate a command or set its defaultsno
ITD serviceitd
ITD statisticsstatistics
ITD service-nameservice-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2529
I Commandsitd statistics
Page 2674
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2530
I Commandsitd statistics
Page 2675
J Commands
• job name, on page 2532• json-pretty, on page 2533• json-pretty, on page 2534• json, on page 2535• json, on page 2536
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2531
Page 2676
job name[no] job name <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Assign a job to the schedulejob
Assign a job to the schedulename
Specify the job names0
Command Mode
• /exec/configure/schedule
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2532
J Commandsjob name
Page 2677
json-pretty| json-pretty
Syntax Description
Pipe command output to filter|
output in json pretty print formatjson-pretty
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2533
J Commandsjson-pretty
Page 2678
json-pretty| json-pretty
Syntax Description
Pipe command output to filter|
output in json pretty print formatjson-pretty
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2534
J Commandsjson-pretty
Page 2679
json| json
Syntax Description
Pipe command output to filter|
output in json formatjson
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2535
J Commandsjson
Page 2680
json| json
Syntax Description
Pipe command output to filter|
output in json formatjson
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2536
J Commandsjson
Page 2681
K Commands
• key-octet-string 7 cryptographic-algorithm AES_128_CMAC, on page 2538• key-octet-string 7 cryptographic-algorithm AES_256_CMAC, on page 2539• key-octet-string cryptographic-algorithm AES_128_CMAC, on page 2540• key-octet-string cryptographic-algorithm AES_256_CMAC, on page 2541• key-server-priority, on page 2542• key-string, on page 2543• key-string 7, on page 2544• key, on page 2545• key, on page 2546• key chain, on page 2547• key config-key hex, on page 2548• kill-everyone, on page 2549• kill background, on page 2550• kstack multicast-udp, on page 2551• kubernetes server ip-address port, on page 2552
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2537
Page 2682
key-octet-string 7 cryptographic-algorithm AES_128_CMAC{ key-octet-string 7 <keystring> cryptographic-algorithm AES_128_CMAC }
Syntax Description
Set key octet stringkey-octet-string
Encryption Type - Proprietary7
key octet stringkeystring
Select CMAC algorithm for authenticationcryptographic-algorithm
cryptographic-algorithm AES-128-CMACAES_128_CMAC
Command Mode
• /exec/configure/macseckeychain-key
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2538
K Commandskey-octet-string 7 cryptographic-algorithm AES_128_CMAC
Page 2683
key-octet-string 7 cryptographic-algorithm AES_256_CMAC{ key-octet-string 7 <keystring> cryptographic-algorithm AES_256_CMAC }
Syntax Description
Set key octet stringkey-octet-string
Encryption Type - Proprietary7
key octet stringkeystring
Select CMAC algorithm for authenticationcryptographic-algorithm
cryptographic-algorithm AES-256-CMACAES_256_CMAC
Command Mode
• /exec/configure/macseckeychain-key
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2539
K Commandskey-octet-string 7 cryptographic-algorithm AES_256_CMAC
Page 2684
key-octet-string cryptographic-algorithm AES_128_CMAC{ key-octet-string [ 0 ] <keystring> cryptographic-algorithm AES_128_CMAC | no key-octet-string [ 0 ]<keystring> cryptographic-algorithm AES_128_CMAC }
Syntax Description
Negate a command or set its defaultsno
Set key octet stringkey-octet-string
(Optional) Encryption Type - No Encryption(default)0
key octet stringkeystring
Select CMAC algorithm for authenticationcryptographic-algorithm
cryptographic-algorithm AES-128-CMACAES_128_CMAC
Command Mode
• /exec/configure/macseckeychain-key
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2540
K Commandskey-octet-string cryptographic-algorithm AES_128_CMAC
Page 2685
key-octet-string cryptographic-algorithm AES_256_CMAC{ key-octet-string [ 0 ] <keystring> cryptographic-algorithm AES_256_CMAC | no key-octet-string [ 0 ]<keystring> cryptographic-algorithm AES_256_CMAC }
Syntax Description
Negate a command or set its defaultsno
Set key octet stringkey-octet-string
(Optional) Encryption Type - No Encryption(default)0
key octet stringkeystring
Select CMAC algorithm for authenticationcryptographic-algorithm
cryptographic-algorithm AES-256-CMACAES_256_CMAC
Command Mode
• /exec/configure/macseckeychain-key
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2541
K Commandskey-octet-string cryptographic-algorithm AES_256_CMAC
Page 2686
key-server-priority[no] key-server-priority <pri>
Syntax Description
Configure Key-Server prioritykey-server-priority
key-server priority valuepri
Command Mode
• /exec/configure/macsec-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2542
K Commandskey-server-priority
Page 2687
key-string{ key-string [ 0 ] <keystring> | no key-string }
Syntax Description
Negate a command or set its defaultsno
Set key stringkey-string
(Optional) Encryption Type - No Encryption(default)0
key stringkeystring
Command Mode
• /exec/configure/keychain-key
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2543
K Commandskey-string
Page 2688
key-string 7{ key-string 7 <keystring> }
Syntax Description
Set key stringkey-string
Encryption Type - Proprietary7
key stringkeystring
Command Mode
• /exec/configure/keychain-key
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2544
K Commandskey-string 7
Page 2689
key[no] key <macsec_keyid>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a macsec keykey
MACsec Key identifier ranging from 1 octet to 32macsec_keyid
Command Mode
• /exec/configure/macseckeychain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2545
K Commandskey
Page 2690
key[no] key <keyid>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a keykey
Key identifierkeyid
Command Mode
• /exec/configure/keychain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2546
K Commandskey
Page 2691
key chain[no] key chain <keychain>
Syntax Description
(Optional) Negate a command or set its defaultsno
Key Managementkey
Keychain Managementchain
key-chain namekeychain
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2547
K Commandskey chain
Page 2692
key config-key hex[no] key config-key { hex | ascii } [ <master-key> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Encryption key for strong encryptionkey
Master-key for strong encryption of secrets in configconfig-key
Key followed should be in hex formathex
Key followed should be in ascii formatascii
(Optional) Enter the Master-keymaster-key
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2548
K Commandskey config-key hex
Page 2693
kill-everyone[no] [ eigrp ] kill-everyone
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) EIGRP router configuration commandseigrp
Kill all adjacencies on SIAkill-everyone
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2549
K Commandskill-everyone
Page 2694
kill backgroundkill background <pid>
Syntax Description
terminate processeskill
kill background processes (started with 'source background <file>'command)
background
background script to terminate, by process-id or just a regex matchingany line from 'show background' command
pid
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2550
K Commandskill background
Page 2695
kstack multicast-udp{ { no kstack multicast-udp } | { kstack multicast-udp { enable | disable } } }
Syntax Description
Negate a command or set its defaultsno
Enable/Disable kstack featurekstack
Clone UDP dest Multicast packets to kstackmulticast-udp
enable
disable
Command Mode
• /exec/configure /exec/configure/config-mgmt
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2551
K Commandskstack multicast-udp
Page 2696
kubernetes server ip-address port[no] kubernetes server ip-address <ip-addr> port <s0> [ vrf <vrf-name> ] | no kubernetes server
Syntax Description
(Optional) Negate a command or set its defaultsno
kuberneteskubernetes
kubernetes serverserver
IP address of the kubernetes hostip-address
ip address of kubernetes Hostip-addr
Port number of the hostport
port numbers0
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2552
K Commandskubernetes server ip-address port
Page 2697
L Commands
• l2rib dup-host-mac-detection, on page 2561• l2rib dup-host-mac-recovery, on page 2562• l2rib event-history size, on page 2563• l3vm event-history, on page 2564• label-allocation-mode per-vrf, on page 2565• label allocate global, on page 2566• lacp fast-select-hot-standby, on page 2567• lacp graceful-convergence, on page 2568• lacp max-bundle, on page 2569• lacp min-links, on page 2570• lacp mode delay, on page 2571• lacp mode delay, on page 2572• lacp port-priority, on page 2573• lacp rapid-transition, on page 2574• lacp rate, on page 2575• lacp rate, on page 2576• lacp suspend-individual, on page 2577• lacp system-mac, on page 2578• lacp system-priority, on page 2579• lacp vpc-convergence, on page 2580• last, on page 2581• latency, on page 2582• latency, on page 2583• latency quantization, on page 2584• latency quantization, on page 2585• layer-2 multicast lookup mac, on page 2586• layer-2 multicast lookup mac, on page 2587• layer2-switched flow monitor input, on page 2588• layer3 peer-router, on page 2589• layer3 peer-router syslog, on page 2590• ldap-search-map, on page 2591• ldap-search-map, on page 2592• ldap-server deadtime, on page 2593
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2553
Page 2698
• ldap-server host, on page 2594• ldap-server host test rootDN, on page 2596• ldap-server port, on page 2597• ldap-server timeout, on page 2598• ldap search-map, on page 2599• less, on page 2600• license expiry check_interval, on page 2601• limit-resource m4route-mem maximum equal-to-min, on page 2602• limit-resource m6route-mem maximum, on page 2603• limit-resource module-type, on page 2604• limit-resource monitor-session-erspan-dst minimum maximum equal-to-min, on page 2605• limit-resource monitor-session-inband-src minimum maximum equal-to-min, on page 2606• limit-resource monitor-session minimum maximum equal-to-min, on page 2607• limit-resource port-channel minimum maximum, on page 2608• limit-resource u4route-mem maximum equal-to-min, on page 2609• limit-resource u6route-mem maximum equal-to-min, on page 2610• limit-resource vlan minimum maximum equal-to-min, on page 2611• limit-resource vrf minimum maximum equal-to-min, on page 2612• limit address-count, on page 2613• line console, on page 2614• line console, on page 2615• line vty, on page 2616• line vty, on page 2617• link-management timers bandwidth, on page 2618• link-state-trap, on page 2619• link debounce, on page 2620• link rxlos, on page 2621• link transmit reset-skip, on page 2622• lisp, on page 2623• lisp ddt, on page 2624• lisp ddt authoritative-prefix eid-prefix, on page 2625• lisp ddt delegate eid-prefix, on page 2626• lisp ddt map-server-peer eid-prefix, on page 2627• lisp ddt root, on page 2628• lisp dynamic-eid, on page 2629• lisp dynamic-eid, on page 2630• lisp explicit-locator-path, on page 2631• lisp explicit-locator-path, on page 2632• lisp extended-subnet-mode, on page 2633• lisp geo-coordinates, on page 2634• lisp instance-id, on page 2635• lisp loc-reach-algorithm, on page 2636• lisp merge-registrations site-id, on page 2637• lisp mobility, on page 2638• lisp mobility test-liveness, on page 2639• lisp security, on page 2640
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2554
L Commands
Page 2699
• lisp site, on page 2641• lisp site, on page 2642• lisp smr-locators, on page 2643• lisp to, on page 2644• list, on page 2645• list, on page 2646• listobject-boolean not, on page 2647• listobject-weight weight threshold-weight, on page 2648• listobject, on page 2649• lldp, on page 2650• lldp dcbx version auto, on page 2651• lldp dcbx version cee, on page 2652• lldp eee rx_wake_time, on page 2653• lldp receive, on page 2654• lldp tlv-select eee, on page 2655• lldp tlv-select management-address v4, on page 2656• lldp tlv-set management-address, on page 2657• lldp tlv-set management-address ipv6, on page 2658• lldp tlv-set vlan, on page 2659• lldp transmit, on page 2660• load-balance, on page 2661• load-balance, on page 2662• load-balance, on page 2663• load-interval, on page 2664• load-interval, on page 2665• load-interval counter, on page 2666• load-interval counter, on page 2667• load, on page 2668• load, on page 2669• load, on page 2670• load, on page 2671• local-as, on page 2672• local-as, on page 2673• local-label prefix, on page 2674• local-label prefix, on page 2675• locator-led, on page 2676• lockdown, on page 2677• log-adjacency-changes, on page 2678• log-adjacency-changes, on page 2679• log-adjacency-changes, on page 2680• log-adjacency-changes, on page 2681• log-adjacency-changes, on page 2682• log-adjacency-changes, on page 2683• log-event-type, on page 2684• log-neighbor-changes, on page 2685• log-neighbor-changes, on page 2686
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2555
L Commands
Page 2700
• log-neighbor-warnings, on page 2687• logging, on page 2688• logging, on page 2689• logging abort, on page 2690• logging console, on page 2691• logging debug, on page 2692• logging distribute, on page 2693• logging drop threshold, on page 2694• logging drop threshold, on page 2695• logging event link enable, on page 2696• logging event port link-status, on page 2697• logging event port link-status, on page 2698• logging event port link-status, on page 2699• logging event port link-status default, on page 2700• logging event port trunk-status, on page 2701• logging event port trunk-status, on page 2702• logging event port trunk-status default, on page 2703• logging flow-mod, on page 2704• logging flow-mod, on page 2705• logging ip access-list cache, on page 2706• logging ip access-list cache entries, on page 2707• logging ip access-list detailed, on page 2708• logging ip access-list include sgt, on page 2709• logging level, on page 2710• logging level, on page 2711• logging level, on page 2712• logging level, on page 2713• logging level, on page 2715• logging level, on page 2716• logging level, on page 2717• logging level, on page 2718• logging level aaa, on page 2719• logging level acllog, on page 2720• logging level aclmgr, on page 2721• logging level adbm, on page 2722• logging level adjmgr, on page 2723• logging level all, on page 2724• logging level amt, on page 2725• logging level arp, on page 2726• logging level ascii-cfg, on page 2727• logging level assoc_mgr, on page 2728• logging level backup, on page 2729• logging level bfd, on page 2730• logging level bgp, on page 2731• logging level bloggerd, on page 2732• logging level bootvar, on page 2733
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2556
L Commands
Page 2701
• logging level callhome, on page 2734• logging level capability, on page 2735• logging level catena, on page 2736• logging level cdp, on page 2737• logging level cert, on page 2738• logging level cfs, on page 2739• logging level clis, on page 2740• logging level clk_mgr, on page 2741• logging level confcheck, on page 2742• logging level copp, on page 2743• logging level core, on page 2744• logging level cts, on page 2745• logging level dhclient, on page 2746• logging level dhcp_snoop, on page 2747• logging level diagclient, on page 2748• logging level diagmgr, on page 2749• logging level dot1x, on page 2750• logging level ecp, on page 2751• logging level eigrp, on page 2752• logging level eltm, on page 2753• logging level epp, on page 2754• logging level ethdstats, on page 2755• logging level ethpm, on page 2756• logging level ethpm link, on page 2757• logging level evb, on page 2758• logging level evmc, on page 2759• logging level evmed, on page 2760• logging level evms, on page 2761• logging level fabric forwarding, on page 2762• logging level fcoe_mgr, on page 2763• logging level feature-mgr, on page 2764• logging level fs-daemon, on page 2765• logging level gpixm, on page 2766• logging level hardware-telemetry, on page 2767• logging level hsrp, on page 2768• logging level icam, on page 2769• logging level igmp, on page 2770• logging level im, on page 2771• logging level imp, on page 2772• logging level interface-vlan, on page 2773• logging level ip pim, on page 2774• logging level ip sla responder, on page 2775• logging level ip sla sender, on page 2776• logging level ip sla twamp-server, on page 2777• logging level ipconf, on page 2778• logging level ipfib, on page 2779
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2557
L Commands
Page 2702
• logging level ipqos, on page 2780• logging level ipv6 pim, on page 2781• logging level iscm, on page 2782• logging level iscm, on page 2783• logging level isis, on page 2784• logging level keystore, on page 2785• logging level l2fm, on page 2786• logging level l2rib, on page 2787• logging level l3vm, on page 2788• logging level lacp, on page 2789• logging level ldap, on page 2790• logging level lem-mgr, on page 2791• logging level license, on page 2792• logging level lim, on page 2793• logging level lisp, on page 2794• logging level lldp, on page 2795• logging level m2rib, on page 2796• logging level mfdm, on page 2797• logging level mfwd, on page 2798• logging level mmode, on page 2799• logging level module, on page 2800• logging level monitor, on page 2801• logging level msdp, on page 2802• logging level mvsh, on page 2803• logging level nat, on page 2804• logging level nbm, on page 2805• logging level netstack, on page 2806• logging level nfm, on page 2807• logging level ngoam, on page 2808• logging level npv, on page 2809• logging level ntp, on page 2810• logging level nxsdk, on page 2811• logging level openflow, on page 2812• logging level orib, on page 2813• logging level ospf, on page 2814• logging level ospfv3, on page 2815• logging level pfstat, on page 2816• logging level pixm, on page 2817• logging level pktmgr, on page 2818• logging level platform, on page 2819• logging level plbm, on page 2820• logging level plcmgr, on page 2821• logging level pltfm_config, on page 2822• logging level plugin, on page 2823• logging level poap, on page 2824• logging level poed, on page 2825
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2558
L Commands
Page 2703
• logging level port-profile, on page 2826• logging level port-resources, on page 2827• logging level port-security, on page 2828• logging level port, on page 2829• logging level port_client, on page 2830• logging level port_lb, on page 2831• logging level port link-failure, on page 2832• logging level private-vlan, on page 2833• logging level ptp, on page 2834• logging level radius, on page 2835• logging level res_mgr, on page 2836• logging level rip, on page 2837• logging level rpm, on page 2838• logging level rsvp, on page 2839• logging level sal, on page 2840• logging level san, on page 2841• logging level scheduler, on page 2842• logging level security, on page 2843• logging level session-mgr, on page 2844• logging level sflow, on page 2845• logging level smartc, on page 2846• logging level smm, on page 2847• logging level snmpd, on page 2848• logging level snmpmib_proc, on page 2849• logging level spanning, on page 2850• logging level spm, on page 2851• logging level stripcl, on page 2852• logging level sysmgr, on page 2853• logging level tacacs, on page 2854• logging level tamnw, on page 2855• logging level track, on page 2856• logging level tunnel, on page 2857• logging level u2rib, on page 2858• logging level u6rib, on page 2859• logging level udld, on page 2860• logging level ufdm, on page 2861• logging level urib, on page 2862• logging level vdc_mgr, on page 2863• logging level virtual-service, on page 2864• logging level vlan_mgr, on page 2865• logging level vmm, on page 2866• logging level vmtracker, on page 2867• logging level vpc, on page 2868• logging level vrrp, on page 2869• logging level vrrpv3, on page 2870• logging level vsan, on page 2871
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2559
L Commands
Page 2704
• logging level vshd, on page 2872• logging level vtp, on page 2873• logging level wwnm, on page 2874• logging level xbar, on page 2875• logging logfile, on page 2876• logging message interface type ethernet, on page 2877• logging module, on page 2878• logging monitor, on page 2879• logging origin-id, on page 2880• logging rate-limit, on page 2881• logging server, on page 2882• logging server dns-refresh-interval, on page 2884• logging source-interface, on page 2885• logging timestamp, on page 2886• login on-failure log, on page 2887• login on-success log, on page 2888• logout-warning, on page 2889• low-memory exempt, on page 2890• lshow, on page 2891• lshow, on page 2892• lsp-gen-interval, on page 2893• lsp-gen-interval, on page 2894• lsp-gen-interval, on page 2895• lsp-mtu, on page 2896• lsp-mtu, on page 2897• lsp-mtu, on page 2898• lsp, on page 2899• lsp, on page 2900• lsp attributes, on page 2901
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2560
L Commands
Page 2705
l2rib dup-host-mac-detection{ no l2rib dup-host-mac-detection } | { l2rib dup-host-mac-detection <num-of-moves> <duration> }
Syntax Description
Negate a command or set its defaultsno
Layer 2 routing information basel2rib
Set Duplicate-Host-MAC-Detection parametersdup-host-mac-detection
Number of host moves to be allowednum-of-moves
Duplicate detection timeout in secs for host movesduration
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2561
L Commandsl2rib dup-host-mac-detection
Page 2706
l2rib dup-host-mac-recovery{ no l2rib dup-host-mac-recovery } | { l2rib dup-host-mac-recovery <timeout> <retry-count> }
Syntax Description
Negate a command or set its defaultsno
Layer 2 routing information basel2rib
Set Duplicate-Host-MAC-Recovery (Unfreeze) parametersdup-host-mac-recovery
Unfreeze timeout (secs)timeout
Unfreeze retry countretry-count
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2562
L Commandsl2rib dup-host-mac-recovery
Page 2707
l2rib event-history sizel2rib event-history { client-tbl | ead-pl | errors | mac | mac-ip | misc-obj | rmac | topology | tx-infra | server }size { default | medium | high | very-high }
Syntax Description
Layer 2 routing information basel2rib
Set event-history size for L2RIBevent-history
L2RIB Client, Producer, Consumer Tables Event Logsclient-tbl
L2RIB EAD, Path-List Objects Event Logsead-pl
L2RIB Error Logserrors
L2RIB MAC Object Event Logsmac
L2RIB MAC Object Event Logsmac-ip
L2RIB IMET, Flood-List, ARP-Signal, Peer ID, Startup-Routes ObjectsEvent Logs
misc-obj
L2RIB Router MAC Object Event Logsrmac
L2RIB Topology Object Event Logstopology
L2RIB TxList, TxSend, TxThread Event Logstx-infra
L2RIB Sysmgr, PSS, HA Logsserver
Sizesize
Default (Low)default
Mediummedium
Highhigh
Very Highvery-high
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2563
L Commandsl2rib event-history size
Page 2708
l3vm event-history[no] l3vm event-history { pss | errors | mts | reinit | cli | vrf | topology } { size { <size_in_text> |<size_in_Kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Debug L3VM informationl3vm
log debug events into event history bufferevent-history
L3VM pss operationpss
L3VM errorserrors
L3VM MTS messagesmts
L3VM reinit eventsreinit
Log L3VM CLI related eventscli
Log VRF related eventsvrf
Log Topology related eventstopology
Configure the size of the event-hist buffersize
Buffer sizesize_in_text
Size of the file in kbytessize_in_Kbytes
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2564
L Commandsl3vm event-history
Page 2709
label-allocation-mode per-vrf[no] label-allocation-mode per-vrf
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure label allocation modelabel-allocation-mode
per VRF label allocation modeper-vrf
Command Mode
• /exec/configure/router-bgp/router-bgp-vrf-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2565
L Commandslabel-allocation-mode per-vrf
Page 2710
label allocate global[no] label allocate global { all-routes | host-routes | prefix-list <pfx-list> }
Syntax Description
(Optional) Negate a command or set its defaultsno
LDP label configurationlabel
Allocate local labelsallocate
Specify default VPN Routing/Forwarding instanceglobal
Allocate local labels for all routesall-routes
Allocate local labels for host routes only (default)host-routes
Specify a prefix-list for local label filteringprefix-list
IP prefix-list for destination prefixespfx-list
Command Mode
• /exec/configure/ldp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2566
L Commandslabel allocate global
Page 2711
lacp fast-select-hot-standbylacp fast-select-hot-standby | no lacp fast-select-hot-standby
Syntax Description
Negate a command or set its defaultsno
Set LACP parameters for the interfacelacp
Configure fast select for hot standby ports. Enabling this feature willallow fast selection of hot standby port when last active port in theport-channel is going down.
fast-select-hot-standby
Command Mode
• /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel/exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2567
L Commandslacp fast-select-hot-standby
Page 2712
lacp graceful-convergencelacp graceful-convergence | no lacp graceful-convergence
Syntax Description
Negate a command or set its defaultsno
Set LACP parameters for the interfacelacp
Configure port-channel lacp graceful convergence. Disable this onlywith lacp ports connected to Non-Nexus peer. Disabling this with Nexuspeer can lead to port suspension
graceful-convergence
Command Mode
• /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel/exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2568
L Commandslacp graceful-convergence
Page 2713
lacp max-bundlelacp max-bundle <max-bundle-number> | no lacp max-bundle [ <max-bundle-number> ]
Syntax Description
Negate a command or set its defaultsno
Set LACP parameters for the interfacelacp
Configure the port-channel max-bundlemax-bundle
Enter the max-bundle numbermax-bundle-number
Command Mode
• /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel/exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2569
L Commandslacp max-bundle
Page 2714
lacp min-linkslacp min-links <min-links-number> | no lacp min-links [ <min-links-number> ]
Syntax Description
Negate a command or set its defaultsno
Set LACP parameters for the interfacelacp
Configure the port-channel min-linksmin-links
Enter the min-link numbermin-links-number
Command Mode
• /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel/exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2570
L Commandslacp min-links
Page 2715
lacp mode delay[no] lacp mode delay
Syntax Description
(Optional) Negate a command or set its defaultsno
Set LACP parameters for the interfacelacp
Enter the LACP modemode
Configure delayed lacp on the port-channeldelay
Command Mode
• /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel/exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2571
L Commandslacp mode delay
Page 2716
lacp mode delay[no] lacp mode delay
Syntax Description
(Optional) Negate a command or set its defaultsno
Set LACP parameters for the interfacelacp
Enter the LACP modemode
Configure delayed lacp on the port-channeldelay
Command Mode
• /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel/exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2572
L Commandslacp mode delay
Page 2717
lacp port-prioritylacp port-priority <port-pri> | no lacp port-priority
Syntax Description
Negate a command or set its defaultsno
Set LACP parameters for the interfacelacp
Set LACP port priorityport-priority
Enter port priorityport-pri
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2573
L Commandslacp port-priority
Page 2718
lacp rapid-transitionlacp rapid-transition | no lacp rapid-transition
Syntax Description
Negate a command or set its defaultsno
Set LACP parameters for the interfacelacp
Optimizes LACP timers for rapid transition from P->I, I->P staterapid-transition
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2574
L Commandslacp rapid-transition
Page 2719
lacp rate[no] lacp rate
Syntax Description
Negate a command or set its defaultsno
Set LACP parameters for the interfacelacp
Configure rate at which PDUs are sent by LACPrate
Command Mode
• /exec/configure/if-ethernet /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all/exec/configure/if-ethernet-m /exec/configure/if-ethernet-switch-m /exec/configure/if-remote-ethernet/exec/configure/if-remote-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2575
L Commandslacp rate
Page 2720
lacp ratelacp rate <rate_type>
Syntax Description
Set LACP parameters for the interfacelacp
Configure rate at which PDUs are sent by LACPrate
Rate typerate_type
Command Mode
• /exec/configure/if-ethernet /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all/exec/configure/if-ethernet-m /exec/configure/if-ethernet-switch-m /exec/configure/if-remote-ethernet/exec/configure/if-remote-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2576
L Commandslacp rate
Page 2721
lacp suspend-individuallacp suspend-individual | no lacp suspend-individual
Syntax Description
Negate a command or set its defaultsno
Set LACP parameters for the interfacelacp
Configure lacp port-channel state. Disabling this will cause lacp to putthe port to individual state and not suspend the port in case it does notget LACP BPDU from the peer ports in the port-channel
suspend-individual
Command Mode
• /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel/exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2577
L Commandslacp suspend-individual
Page 2722
lacp system-maclacp system-mac <mac-address> [ role <role> ] | no lacp system-mac
Syntax Description
Negate a command or set its defaultsno
Set LACP parameters for the interfacelacp
Configure theMAC address to be used for the LACP Protocol exchangessystem-mac
MAC-address(FORMAT :xxxx.xxxx.xxxx)mac-address
(Optional) Configure the role for this Switchrole
(Optional) Role played by the Switchrole
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2578
L Commandslacp system-mac
Page 2723
lacp system-prioritylacp system-priority <sys-pri> | no lacp system-priority
Syntax Description
Negate a command or set its defaultsno
Set LACP parameters for the interfacelacp
Set LACP system prioritysystem-priority
Enter System Prioritysys-pri
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2579
L Commandslacp system-priority
Page 2724
lacp vpc-convergencelacp vpc-convergence | no lacp vpc-convergence
Syntax Description
Negate a command or set its defaultsno
Set LACP parameters for the interfacelacp
Enable lacp convergence for vPC port channels.vpc-convergence
Command Mode
• /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel/exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2580
L Commandslacp vpc-convergence
Page 2725
last| last [ <lines> ]
Syntax Description
Pipe command output to filter|
Display last lineslast
(Optional) number of lines to printlines
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2581
L Commandslast
Page 2726
latency{ [ no ] latency <lat> | no latency }
Syntax Description
Provide the latency value for this POSTCARD queue_profilelatency
queue_profile latency (nano seconds). Default is 2048 nslat
Command Mode
• /exec/configure/config-postcard-q-prof
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2582
L Commandslatency
Page 2727
latency{ [ no ] latency <lat> | no latency }
Syntax Description
Provide the latency value for this INT queue_profilelatency
queue_profile latency (nano seconds). Default is 2048 nslat
Command Mode
• /exec/configure/config-int-q-prof
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2583
L Commandslatency
Page 2728
latency quantization{ [ no ] latency quantization <lat> | no latency quantization }
Syntax Description
Provide the latency value for this POSTCARD flow-profilelatency
Provide the latency value for this POSTCARD flow-profilequantization
flow-profile latency quantization. This value will be converted to apower of 2 (nanoseconds). For example, value of 11 will be convertedto 2 power 11 which is 2048. This means that if the difference betweeningress timestamp and egress timestamp is more than 2048 nanosec atany popostcard in the path, one upstream report or local report will begenerated per flow. The allowed values are in range 0-31. Default is 11.
lat
Command Mode
• /exec/configure/config-postcard-flow-prof
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2584
L Commandslatency quantization
Page 2729
latency quantization{ [ no ] latency quantization <lat> | no latency quantization }
Syntax Description
Provide the latency value for this INT flow-profilelatency
Provide the latency value for this INT flow-profilequantization
flow-profile latency quantization. This value will be converted to apower of 2 (nanoseconds). For example, value of 11 will be convertedto 2 power 11 which is 2048. This means that if the difference betweeningress timestamp and egress timestamp is more than 2048 nanosec atany point in the path, one upstream report or local report will begenerated per flow. The allowed values are in range 0-28 Default is 11.
lat
Command Mode
• /exec/configure/config-int-flow-prof
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2585
L Commandslatency quantization
Page 2730
layer-2 multicast lookup mac[no] layer-2 multicast lookup mac
Syntax Description
(Optional) Negate a command or set its defaultsno
set layer2 multicast lkup modelayer-2
set layer2 multicast lkup modemulticast
lkup type can be either mac or ip basedlookup
set mac based multicast lkup modemac
Command Mode
• /exec/configure/vlan-config /exec/configure/bdomain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2586
L Commandslayer-2 multicast lookup mac
Page 2731
layer-2 multicast lookup mac[no] layer-2 multicast lookup mac
Syntax Description
(Optional) Negate a command or set its defaultsno
set layer2 multicast lkup modelayer-2
set layer2 multicast lkup modemulticast
lkup type can be either mac or ip basedlookup
set mac based multicast lkup modemac
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2587
L Commandslayer-2 multicast lookup mac
Page 2732
layer2-switched flow monitor input[no] layer2-switched flow monitor <monitorname> input
Syntax Description
Configure L2 featureslayer2-switched
NetFlow related commandsflow
Apply a Flow Monitor to this interfacemonitor
Name of Flow Monitormonitorname
Apply Flow Monitor on input trafficinput
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2588
L Commandslayer2-switched flow monitor input
Page 2733
layer3 peer-routerlayer3 peer-router | no layer3 peer-router
Syntax Description
Negate a command or set its defaultsno
Enable layer 3 functionalitylayer3
no change for TTL of packets destined to the peerpeer-router
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2589
L Commandslayer3 peer-router
Page 2734
layer3 peer-router sysloglayer3 peer-router syslog [ interval <syslog-interval> ] | no layer3 peer-router syslog
Syntax Description
Negate a command or set its defaultsno
Enable layer 3 functionalitylayer3
no change for TTL of packets destined to the peerpeer-router
print layer 3 protocol syslogsyslog
(Optional) how frequent to print the sysloginterval
(Optional) how many seconds to print a syslogsyslog-interval
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2590
L Commandslayer3 peer-router syslog
Page 2735
ldap-search-map[no] ldap-search-map
Syntax Description
Negate a command or set its defaultsno
Set one of the configured search-map as activeldap-search-map
Command Mode
• /exec/configure/ldap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2591
L Commandsldap-search-map
Page 2736
ldap-search-mapldap-search-map <s0>
Syntax Description
Set one of the configured search-map as activeldap-search-map
Name of the search-maps0
Command Mode
• /exec/configure/ldap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2592
L Commandsldap-search-map
Page 2737
ldap-server deadtime[no] ldap-server deadtime <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure LDAP related parametersldap-server
Global LDAP server deadtime period in secondsdeadtime
LDAP server deadtime period in minutes (default 0 mins -disabled)i0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2593
L Commandsldap-server deadtime
Page 2738
ldap-server host[no] ldap-server host { <hostipname> } [ { enable-ssl | port <i1> [ timeout <i2> ] | rootDN <s0> [ password{ 7 <s1> { { [ port1 <i3> [ timeout1 <i4> ] ] } | { [ timeout5 <i9> ] } } | <s2> { { [ port2 <i5> [ timeout2 <i6>] ] } | { [ timeout4 <i8> ] } } } ] | timeout3 <i7> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure LDAP related parametersldap-server
LDAP server's DNS name or IP addresshost
IPV4/IPV6 address or DNS namehostipname
(Optional) LDAP server enable sslenable-ssl
(Optional) LDAP server's port (default: global config)port
(Optional) port numberi1
(Optional) LDAP server timeout period in secondstimeout
(Optional) LDAP server timeout in seconds (default: global config)i2
(Optional) LDAP server root DNrootDN
(Optional) root DNs0
(Optional) LDAP server root passwordpassword
(Optional) LDAP root password (encrypted)7
(Optional) password (encrypted)s1
(Optional) LDAP server's port (default: global config)port1
(Optional) port numberi3
(Optional) LDAP server timeout period in secondstimeout1
(Optional) LDAP server timeout in seconds (default: global config)i4
(Optional) password (clear text)s2
(Optional) LDAP server's port (default: global config)port2
(Optional) port numberi5
(Optional) LDAP server timeout period in secondstimeout2
(Optional) LDAP server timeout in seconds (default: global config)i6
(Optional) LDAP server timeout period in secondstimeout3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2594
L Commandsldap-server host
Page 2739
(Optional) LDAP server timeout in seconds (default: global config)i7
(Optional) LDAP server timeout period in secondstimeout4
(Optional) LDAP server timeout in seconds (default: global config)i8
(Optional) LDAP server timeout period in secondstimeout5
(Optional) LDAP server timeout in seconds (default: global config)i9
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2595
L Commandsldap-server host
Page 2740
ldap-server host test rootDN[no] ldap-server host { <hostipname> } test rootDN <r1> { { [ username <s0> { [ password { [ 7 <s2> | <s1>] } [ idle-time <i1> ] ] | [ idle-time <i1> ] } ] } | { [ password { [ 7 <s2> | <s1> ] } [ idle-time <i1> ] ] } | { [idle-time <i1> ] } }
Syntax Description
(Optional) <s0>username
(Optional) Negate a command or set its defaultsno
Configure LDAP related parametersldap-server
LDAP server's IP addresshost
IPV4/IPV6 address or DNS namehostipname
Parameters to send test packetstest
(Optional) LDAP test password (encrypted)7
(Optional) user names0
(Optional) user password in test packetspassword
(Optional) test passwords1
(Optional) test password (encrypted)s2
rootDN in test packetsrootDN
root DNr1
(Optional) time interval for monitoring the serveridle-time
(Optional) time period in minutesi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2596
L Commandsldap-server host test rootDN
Page 2741
ldap-server port[no] ldap-server port <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure LDAP related parametersldap-server
Global LDAP server's port (default 389)port
port numberi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2597
L Commandsldap-server port
Page 2742
ldap-server timeout[no] ldap-server timeout <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure LDAP related parametersldap-server
Global LDAP server timeout period in secondstimeout
LDAP server timeout period in seconds (default 5 sec)i0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2598
L Commandsldap-server timeout
Page 2743
ldap search-map[no] ldap search-map <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure information about ldapldap
Configure the search-mapsearch-map
Search Map Names0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2599
L Commandsldap search-map
Page 2744
less| less [ -d | -E ] +
Syntax Description
Pipe command output to filter|
Filter for pagingless
(Optional) dumb terminal-d
(Optional) quit at end of file-E
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2600
L Commandsless
Page 2745
license expiry check_intervallicense expiry check_interval <i0>
Syntax Description
Enter the license configuration modelicense
Configure the expiry check intervalexpiry
Configure the expiry check intervalcheck_interval
Specify the license expiry check interval in secondsi0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2601
L Commandslicense expiry check_interval
Page 2746
limit-resource m4route-mem maximum equal-to-min{ limit-resource m4route-mem [ minimum { <min> | <min-hi> } ] maximum { <max-lo> | <max> | <max-hi>| equal-to-min } } | { no limit-resource m4route-mem [ [ minimum { <min> | <min-hi> } ] maximum {<max-lo> | <max> | <max-hi> | equal-to-min } ] }
Syntax Description
Negate a command or set its defaultsno
Resource configurationlimit-resource
set ipv4 route memory limitsm4route-mem
(Optional) minimum route memory to allocateminimum
(Optional) minimum route memory valuemin
(Optional) minimum route memory valuemin-hi
maximum route memory to allocatemaximum
maximum route memory valuemax-lo
maximum route memory valuemax
maximum route memory valuemax-hi
maximum value equal to minequal-to-min
Command Mode
• /exec/configure/vdc-template /exec/configure/vdc
Usage Guidelines
You can set only one value for the resource maximum or minimum limits. If you specify a minimum limit,the maximum limit is ignored, but that value is displayed for both the minimum and maximum limits. If youspecify only a maximum limit, that value is displayed for both the minimum and maximum limits.
Note
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2602
L Commandslimit-resource m4route-mem maximum equal-to-min
Page 2747
limit-resource m6route-mem maximum{ limit-resource m6route-mem [ minimum { <min> | <min-hi> } ] maximum { <max-lo> | <max> | <max-hi>} } | { no limit-resource m6route-mem [ [ minimum { <min> | <min-hi> } ] maximum { <max-lo> | <max>| <max-hi> } ] }
Syntax Description
Negate a command or set its defaultsno
Resource configurationlimit-resource
set ipv6 route memory limitsm6route-mem
(Optional) minimum route memory to allocateminimum
(Optional) minimum route memory valuemin
(Optional) minimum route memory valuemin-hi
maximum route memory to allocatemaximum
maximum route memory valuemax-lo
maximum route memory valuemax
maximum route memory valuemax-hi
Command Mode
• /exec/configure/vdc-template /exec/configure/vdc
Usage Guidelines
You can set only one value for the resource maximum or minimum limits. If you specify a minimum limit,the maximum limit is ignored, but that value is displayed for both the minimum and maximum limits. If youspecify only a maximum limit, that value is displayed for both the minimum and maximum limits.
Note
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2603
L Commandslimit-resource m6route-mem maximum
Page 2748
limit-resource module-type{ limit-resource module-type <card-type> + } | { no limit-resource module-type }
Syntax Description
Negate a command or set its defaultsno
Resource configurationlimit-resource
Controls which type of modules are allowed in this vdcmodule-type
Allowed module typescard-type
Command Mode
• /exec/configure/vdc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2604
L Commandslimit-resource module-type
Page 2749
limit-resource monitor-session-erspan-dst minimum maximumequal-to-min
{ limit-resource monitor-session-erspan-dst minimum <min-val> maximum { <max-val> | equal-to-min } }| { no limit-resource monitor-session-erspan-dst [ minimum <min-val> maximum { <max-val> | equal-to-min} ] }
Syntax Description
Resource configurationlimit-resource
Monitor erspan destination sessionmonitor-session-erspan-dst
minimum monitor erspan-dst session to allocateminimum
minimum monitor erspan-dst session valuemin-val
maximum monitor erspan-dst session to allocatemaximum
maximum monitor erspan-dst session valuemax-val
set maximum value equal to minequal-to-min
Command Mode
• /exec/configure/vdc-template /exec/configure/vdc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2605
L Commandslimit-resource monitor-session-erspan-dst minimum maximum equal-to-min
Page 2750
limit-resource monitor-session-inband-src minimummaximumequal-to-min
{ limit-resource monitor-session-inband-src minimum <min-val> maximum { <max-val> | equal-to-min } }| { no limit-resourcemonitor-session-inband-src [ minimum<min-val>maximum { <max-val> | equal-to-min} ] }
Syntax Description
Resource configurationlimit-resource
Monitor inband sourcemonitor-session-inband-src
minimum monitor inband source to allocateminimum
minimum monitor inband source valuemin-val
maximum monitor inband source to allocatemaximum
maximum monitor inband source valuemax-val
set maximum value equal to minequal-to-min
Command Mode
• /exec/configure/vdc-template /exec/configure/vdc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2606
L Commandslimit-resource monitor-session-inband-src minimum maximum equal-to-min
Page 2751
limit-resourcemonitor-sessionminimummaximumequal-to-min{ limit-resource monitor-session minimum <min-val> maximum { <max-val> | equal-to-min } } | { nolimit-resource monitor-session [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }
Syntax Description
Resource configurationlimit-resource
Monitor local/erspan-source sessionmonitor-session
minimum monitor local session to allocateminimum
minimum monitor local session valuemin-val
maximum monitor local session to allocatemaximum
maximum monitor local session valuemax-val
set maximum value equal to minequal-to-min
Command Mode
• /exec/configure/vdc-template /exec/configure/vdc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2607
L Commandslimit-resource monitor-session minimum maximum equal-to-min
Page 2752
limit-resource port-channel minimum maximumlimit-resource port-channel minimum <min-val> maximum { <max-val> | equal-to-min } | no limit-resourceport-channel [ minimum <min-val> maximum { <max-val> | equal-to-min } ]
Syntax Description
Negate a command or set its defaultsno
Resource configurationlimit-resource
set port-channel limitsport-channel
minimum port-channels to allocateminimum
min-val
maximum port-channels to allocatemaximum
max-val
set maximum value equal to minequal-to-min
Command Mode
• /exec/configure/vdc-template /exec/configure/vdc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2608
L Commandslimit-resource port-channel minimum maximum
Page 2753
limit-resource u4route-mem maximum equal-to-min{ limit-resource u4route-mem [ minimum { <min-lo> | <min> | <min-hi> } ] maximum { <max-lo> | <max>| <max-hi> | equal-to-min } } | { no limit-resource u4route-mem [ [ minimum { <min-lo> | <min> | <min-hi>} ] maximum { <max-lo> | <max> | <max-hi> | equal-to-min } ] }
Syntax Description
Negate a command or set its defaultsno
Resource configurationlimit-resource
set ipv4 route memory limitsu4route-mem
(Optional) minimum route memory to allocateminimum
(Optional) minimum route memory valuemin-lo
(Optional) minimum route memory valuemin
(Optional) minimum route memory valuemin-hi
maximum route memory to allocatemaximum
maximum route memory valuemax-lo
maximum route memory valuemax
maximum route memory valuemax-hi
maximum value equal to minequal-to-min
Command Mode
• /exec/configure/vdc-template /exec/configure/vdc
Usage Guidelines
You can set only one value for the resource maximum or minimum limits. If you specify a minimum limit,the maximum limit is ignored, but that value is displayed for both the minimum and maximum limits. If youspecify only a maximum limit, that value is displayed for both the minimum and maximum limits.
Note
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2609
L Commandslimit-resource u4route-mem maximum equal-to-min
Page 2754
limit-resource u6route-mem maximum equal-to-min{ limit-resource u6route-mem [ minimum { <min-lo> | <min> | <min-hi> } ] maximum { <max-lo> | <max>| <max-hi> | equal-to-min } } | { no limit-resource u6route-mem [ [ minimum { <min-lo> | <min> | <min-hi>} ] maximum { <max-lo> | <max> | <max-hi> | equal-to-min } ] }
Syntax Description
Negate a command or set its defaultsno
Resource configurationlimit-resource
set ipv6 route memory limitsu6route-mem
(Optional) minimum route memory to allocateminimum
(Optional) minimum route memory valuemin-lo
(Optional) minimum route memory valuemin
(Optional) minimum route memory valuemin
(Optional) minimum route memory valuemin-hi
maximum route memory to allocatemaximum
maximum route memory valuemax-lo
maximum route memory valuemax
maximum route memory valuemax-hi
maximum value equal to minequal-to-min
Command Mode
• /exec/configure/vdc-template /exec/configure/vdc
Usage Guidelines
You can set only one value for the resource maximum or minimum limits. If you specify a minimum limit,the maximum limit is ignored, but that value is displayed for both the minimum and maximum limits. If youspecify only a maximum limit, that value is displayed for both the minimum and maximum limits.
Note
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2610
L Commandslimit-resource u6route-mem maximum equal-to-min
Page 2755
limit-resource vlan minimum maximum equal-to-min{ limit-resource vlan minimum <min-val> maximum { <max-val> | equal-to-min } } | { no limit-resourcevlan [ minimum <min-val> maximum { <max-val> | equal-to-min } ] }
Syntax Description
Negate a command or set its defaultsno
Resource configurationlimit-resource
set VLAN limitsvlan
minimum VLANs to allocateminimum
minimum VLANs valuemin-val
maximum VLANs to allocatemaximum
maximum VLANs valuemax-val
set maximum value equal to minequal-to-min
Command Mode
• /exec/configure/vdc-template /exec/configure/vdc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2611
L Commandslimit-resource vlan minimum maximum equal-to-min
Page 2756
limit-resource vrf minimum maximum equal-to-min{ limit-resource vrf minimum <number1> maximum { <number2> | equal-to-min } } | { no limit-resourcevrf [ minimum <number1> maximum { <number2> | equal-to-min } ] }
Syntax Description
Negate a command or set its defaultsno
Resource configurationlimit-resource
set vrf resource limitsvrf
minimum vrf resources to allocateminimum
minimum vrf resource valuenumber1
maximum vrf resources to allocatemaximum
maximum vrf resource valuenumber2
set maximum value equal to minequal-to-min
Command Mode
• /exec/configure/vdc-template /exec/configure/vdc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2612
L Commandslimit-resource vrf minimum maximum equal-to-min
Page 2757
limit address-count[no] limit address-count <addr_count>
Syntax Description
(Optional) Negate a command or set its defaultsno
maximum valueaddr_count
Command Mode
• /exec/configure/config-snoop-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2613
L Commandslimit address-count
Page 2758
line console[no] line console
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a terminal lineline
Primary terminal lineconsole
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2614
L Commandsline console
Page 2759
line console[no] line console
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a terminal lineline
Primary terminal lineconsole
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2615
L Commandsline console
Page 2760
line vtyline vty
Syntax Description
Configure a terminal lineline
Virtual terminal linevty
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2616
L Commandsline vty
Page 2761
line vty[no] line vty
Syntax Description
Negate a command or set its defaultsno
Configure a terminal lineline
Virtual terminal linevty
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2617
L Commandsline vty
Page 2762
link-management timers bandwidth[no] link-management timers { bandwidth-hold | periodic-flooding } | link-management timers { bandwidth-hold<bw_seconds> | periodic-flooding <flood_seconds> }
Syntax Description
Negate a command or set its defaultsno
Link Management configurationlink-management
Link Management timers configurationtimers
Link Management bandwidth hold timerbandwidth-hold
secondsbw_seconds
Link Management periodic flooding intervalperiodic-flooding
seconds [0 to disable, minimum set to 30]flood_seconds
Command Mode
• /exec/configure/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2618
L Commandslink-management timers bandwidth
Page 2763
link-state-trap[no] link-state-trap
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/disable link state change trapslink-state-trap
Command Mode
• /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext /exec/configure/if-fcip/exec/configure/if-iscsi
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2619
L Commandslink-state-trap
Page 2764
link debouncelink debounce { [ link-up [ time <time_val_link_up> ] ] | [ time <time_val> ] } | no link debounce [ link-up]
Syntax Description
Negate a command or set its defaultsno
Configure linklink
Configure link debounce timerdebounce
(Optional) Timer for the link-up eventlink-up
(Optional) Link debounce timetime
(Optional) Timer value (in milliseconds)time_val
(Optional) Timer value (in milliseconds)time_val_link_up
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2620
L Commandslink debounce
Page 2765
link rxloslink rxlos [ algo <algo_val> ] | no link rxlos [ algo <algo_val> ]
Syntax Description
Negate a command or set its defaultsno
Configure linklink
Configure link rxlos algorxlos
(Optional) Link rxlos algo controlalgo
(Optional) rxlos control optionsalgo_val
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-sub
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2621
L Commandslink rxlos
Page 2766
link transmit reset-skip{ link transmit reset-skip | no link transmit reset-skip }
Syntax Description
Negate a command or set its defaultsno
Configure linklink
Configure link transmit for interfacetransmit
Configure link transmit for interfacereset-skip
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2622
L Commandslink transmit reset-skip
Page 2767
lisp{ lisp-lig | lig } { version | self | self6 | <hostname> | { <eid> | <eid6> } } [ source { <seid> | <seid6> } ] [ to{ <mr-hostname> | { <mr> | <mr6> } } ] [ count <count> ] [ probe ] [ vrf { <vrf-name> | <vrf-known-name>} ]
Syntax Description
LISP Internet Groperlisp-lig
LISP Internet Groperlig
LIG on a IPv4 Endpoint ID (EID)eid
Display Internet Draft version lig supportsversion
Test if IPv4 EID-prefix registered in mapping databaseself
Test if IPv6 EID-prefix registered in mapping databaseself6
DNS name for Endpoint ID (EID)hostname
(Optional) Provide source EID for Map-Requestsource
(Optional) Source IPv4 Endpoint ID (EID)seid
(Optional) Where to send the Map-Requestto
(Optional) DNS name for Map-Resolvermr-hostname
(Optional) Map-Resolver IPv4 address to send Map-Request tomr
(Optional) Map-Requests to send before Map-Reply returnedcount
(Optional) Number of Map-Requestscount
(Optional) RLOC-probe each locatorprobe
(Optional) LIGing for specific VRFvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2623
L Commandslisp
Page 2768
lisp ddt{ [ no ] lisp ddt }
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configures a LISP-DDT mapping system functionalityddt
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2624
L Commandslisp ddt
Page 2769
lisp ddt authoritative-prefix eid-prefix{ [ no ] lisp ddt authoritative-prefix eid-prefix { <eid-prefix> | <eid-prefix6> } } | { [ no ] lisp ddtauthoritative-prefix instance-id <iid> [ eid-prefix { <eid-prefix> | <eid-prefix6> } ] } | { [ no ] lisp ddtauthoritative-prefix <star> } | { [ no ] lisp ddt authoritative-prefix instance-id { <iidp> | <range> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configure LISP-DDT parametersddt
Configure EID-prefix this LISP-DDT node is authoritative forauthoritative-prefix
Instance ID of VPN for EID-prefixinstance-id
Instance-ID valueiid
Authoritative prefix on root for all address spacestar
Instance-ID in prefix formatiidp
Instance-ID range in 'x-y' format where y > xrange
Authoritative IPv4 or IPv6 EID-prefixeid-prefix
EID-prefix in IPv4 slash formateid-prefix
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2625
L Commandslisp ddt authoritative-prefix eid-prefix
Page 2770
lisp ddt delegate eid-prefix{ [ no ] lisp ddt delegate { <node> | <node6> } { eid-prefix { <eid-prefix> | <eid-prefix6> } } [ priority<priority> weight <weight> ] [ public-key <key> ] [ map-server ] } | { [ no ] lisp ddt delegate { <node> |<node6> } instance-id <iid> [ eid-prefix { <eid-prefix> | <eid-prefix6> } ] [ priority <priority>weight <weight>] [ public-key <key> ] [ map-server ] } | { [ no ] lisp ddt delegate { <node> | <node6> } instance-id { <iidp>| <range> } [ priority <priority> weight <weight> ] [ public-key <key> ] [ map-server ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configure LISP-DDT parametersddt
Configure LISP-DDT child in delegation hierarchydelegate
IPv4 locator address of DDT nodenode
Instance ID of VPN for EID-prefixinstance-id
Instance-ID valueiid
Instance-ID in prefix formatiidp
Instance-ID range in 'x-y' format where y > xrange
Child delegration for IPv4 or IPv6 EID-prefixeid-prefix
EID-prefix in IPv4 slash formateid-prefix
(Optional) Configures which Locators from a set are preferredpriority
(Optional) Lower priority Locator takes preferencepriority
(Optional) Traffic load-spreading among Locatorsweight
(Optional) Specified in a percentage from 0 to 100weight
(Optional) Child delegate is a Map-Servermap-server
(Optional) DDT child's public key this DDT-node supplies for referralspublic-key
(Optional) RSA public-keykey
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2626
L Commandslisp ddt delegate eid-prefix
Page 2771
lisp ddt map-server-peer eid-prefix{ [ no ] lisp ddt map-server-peer { <node> | <node6> } { eid-prefix { <eid-prefix> | <eid-prefix6> } } [ priority<priority> weight <weight> ] [ public-key <key> ] } | { [ no ] lisp ddt map-server-peer { <node> | <node6>} instance-id <iid> [ eid-prefix { <eid-prefix> | <eid-prefix6> } ] [ priority <priority> weight <weight> ] [public-key <key> ] } | { [ no ] lisp ddt map-server-peer { <node> | <node6> } instance-id { <iidp> | <range>} [ priority <priority> weight <weight> ] [ public-key <key> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configure LISP-DDT parametersddt
Configure other map-server peersmap-server-peer
IPv4 locator address of DDT nodenode
Instance ID of VPN for EID-prefixinstance-id
Instance-ID valueiid
Instance-ID in prefix formatiidp
Instance-ID range in 'x-y' format where y > xrange
Child delegration for IPv4 or IPv6 EID-prefixeid-prefix
EID-prefix in IPv4 slash formateid-prefix
(Optional) Configures which Locators from a set are preferredpriority
(Optional) Lower priority Locator takes preferencepriority
(Optional) Traffic load-spreading among Locatorsweight
(Optional) Specified in a percentage from 0 to 100weight
(Optional) DDT child's public key this DDT-node supplies for referralspublic-key
(Optional) RSA public-keykey
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2627
L Commandslisp ddt map-server-peer eid-prefix
Page 2772
lisp ddt root[no] lisp ddt root { <root> | <root6> } [ public-key <key> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configure LISP-DDT parametersddt
Configure LISP-DDT root of tree in Map-Resolverroot
IPv4 locator address of DDT rootroot
(Optional) DDT root's public key used to verify signed Map-Referralspublic-key
(Optional) RSA public-keykey
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2628
L Commandslisp ddt root
Page 2773
lisp dynamic-eid{ [ no ] lisp dynamic-eid <dyn-eid-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configure dynamic-EIDs for roamingdynamic-eid
Name your dynamic-EIDdyn-eid-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2629
L Commandslisp dynamic-eid
Page 2774
lisp dynamic-eid{ [ no ] lisp dynamic-eid <dyn-eid-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configure dynamic-EIDs for roamingdynamic-eid
Name your dynamic-EIDdyn-eid-name
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2630
L Commandslisp dynamic-eid
Page 2775
lisp explicit-locator-path[no] lisp explicit-locator-path <elp-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configures a LISP Explicit Locator Path (ELP)explicit-locator-path
Name of LISP ELPelp-name
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2631
L Commandslisp explicit-locator-path
Page 2776
lisp explicit-locator-path{ [ no ] lisp explicit-locator-path <elp-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configures a LISP Explicit Locator Path (ELP)explicit-locator-path
Name of LISP ELPelp-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2632
L Commandslisp explicit-locator-path
Page 2777
lisp extended-subnet-mode{ [ no ] lisp extended-subnet-mode }
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP interface configuration commandslisp
Create dynamic-EID state when EIDs reside on their home subnetextended-subnet-mode
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2633
L Commandslisp extended-subnet-mode
Page 2778
lisp geo-coordinates[no] lisp geo-coordinates <latitude> <longitude> [ <altitude> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configure Geo Coordinates for this routergeo-coordinates
Latitude in DMS format: 'degree-min-sec-N' or 'degree-min-sec-Slatitude
Longitude in DMS format: 'degree-min-sec-E' or 'degree-min-sec-Wformat
longitude
(Optional) Altitude in meters above sea-levelaltitude
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2634
L Commandslisp geo-coordinates
Page 2779
lisp instance-id[no] lisp instance-id <iid>
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configures Instance-ID for global data-mappingsinstance-id
24-bit instance-ID valueiid
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2635
L Commandslisp instance-id
Page 2780
lisp loc-reach-algorithm[no] lisp loc-reach-algorithm { count-tcp | echo-nonce | { rloc-probing [ map-request-on-failure ] } }
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configure locator reachability algorithmloc-reach-algorithm
Count TCP SYNs and ACKscount-tcp
Request for nonce to echo back in data-planeecho-nonce
Probe each high-priority RLOC with Map-Request as last resortrloc-probing
(Optional) Send Map-Request to database mapping system when anyRLOC for a map-cache entry becomes RLOC-probing unreachable
map-request-on-failure
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2636
L Commandslisp loc-reach-algorithm
Page 2781
lisp merge-registrations site-id[no] lisp merge-registrations site-id <site-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
ETRs merge registrations from Map-Notify messagesmerge-registrations
Configure site-id value for each xTR at sitesite-id
Site-ID to group xTRs togethersite-id
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2637
L Commandslisp merge-registrations site-id
Page 2782
lisp mobility[no] lisp mobility <dyn-eid-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP interface configuration commandslisp
Configures to allow EID mobility on interfacemobility
Name of the dynamic-EID to usedyn-eid-name
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2638
L Commandslisp mobility
Page 2783
lisp mobility test-liveness[no] lisp mobility test-liveness
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP interface configuration commandslisp
Configures to allow EID mobility on interfacemobility
Ping discovered dyn-eid hosts on this interface periodically to determinehost liveness
test-liveness
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2639
L Commandslisp mobility test-liveness
Page 2784
lisp security[no] lisp security [ strong ]
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configure LISP-SEC on ITR or PITRsecurity
(Optional) Reject Map-Replies without LISP-SEC signatures includedstrong
Command Mode
• /exec/configure /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2640
L Commandslisp security
Page 2785
lisp site{ [ no ] lisp site <site-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configures LISP sites in a map-serversite
Name your LISP sitesite-name
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2641
L Commandslisp site
Page 2786
lisp site{ [ no ] lisp site <site-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Configures LISP sites in a map-serversite
Name your LISP sitesite-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2642
L Commandslisp site
Page 2787
lisp smr-locators[no] lisp smr-locators
Syntax Description
(Optional) Negate a command or set its defaultsno
LISP global configuration commandslisp
Send SMR to all RLOCs in locator-set for map-cache entrysmr-locators
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2643
L Commandslisp smr-locators
Page 2788
lisp to{ lisp-rig | rig } [ instance-id <iid> ] { <hostname> | { <eid> | <eid6> } } to { <ddt-hostname> | { <ddt> |<ddt6> } }
Syntax Description
LISP-DDT Referral Internet Groperlisp-rig
LISP-DDT Referral Internet Groperrig
(Optional) Instance-ID of VPN EID resides ininstance-id
(Optional) 24-bit instance-ID valueiid
RIG on a IPv4 Endpoint ID (EID)eid
DNS name for Endpoint ID (EID)hostname
Where to send the Map-Requestto
DNS name for DDT-nodeddt-hostname
DDT-node IPv4 address to send Map-Request toddt
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2644
L Commandslisp to
Page 2789
listlist [ <index> ]
Syntax Description
Re-list all or part of the explicit path entrieslist
(Optional) List starting at entry index numberindex
Command Mode
• /exec/configure/te/expl-path
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2645
L Commandslist
Page 2790
listlist
Syntax Description
Re-list all of the attribute list entrieslist
Command Mode
• /exec/configure/te/lsp-attr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2646
L Commandslist
Page 2791
listobject-boolean notlistobject-boolean <object-id> not
Syntax Description
Configure Object as member of tracking listlistobject-boolean
Tracked objectobject-id
Negate Up statusnot
Command Mode
• /exec/configure/tr-list-bool
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2647
L Commandslistobject-boolean not
Page 2792
listobject-weight weight threshold-weightlistobject-weight { <object-id> weight <weight-val> } | threshold-weight { weight-thresh { weightup<up-weight> [ weightdown <down-weight> ] | weightdown <down-weight> [ weightup <up-weight> ] } } |no threshold-weight weight-thresh
Syntax Description
Negate a command or set its defaultsno
Configure Object as member of tracking listlistobject-weight
Tracked Objectobject-id
Assign a weight to objectweight
Assign a weight to objectweight-val
Threshold parametersthreshold-weight
Weight thresholdweight-thresh
Up thresholdweightup
Up threshold weightup-weight
(Optional) Down thresholdweightdown
(Optional) Down threshold weightdown-weight
Command Mode
• /exec/configure/tr-list-thrw
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2648
L Commandslistobject-weight weight threshold-weight
Page 2793
listobject[no] listobject <object-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Object as member of tracking listlistobject
Tracked Objectobject-id
Command Mode
• /exec/configure/tr-list-thrw /exec/configure/tr-list-thrp /exec/configure/tr-list-bool
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2649
L Commandslistobject
Page 2794
lldp[no] lldp { holdtime <i0> | reinit <i1> | timer <i2> | portid-subtype <i3> | tlv-select { management-address |port-description | port-vlan | power-management | system-capabilities | system-description | system-name |dcbxp } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure global LLDP parameterslldp
Specify the holdtime (in sec) to be sent in packetsholdtime
holdtime in seci0
Delay (in sec) for LLDP initialisation on any interfacereinit
reinit in seci1
Specify the rate at which LLDP packets are sent (in sec)timer
rate of packets in seci2
config portid subtype for LLDP TLV and SNMP MIBsportid-subtype
0: long interface name (default), 1: short interface namei3
Selection of LLDP to sendtlv-select
Management Address TLVmanagement-address
Port Description TLVport-description
Port Vlan ID TLVport-vlan
IEEE 802.3 DTE Power via MDI TLVpower-management
System Capabilities TLVsystem-capabilities
System Description TLVsystem-description
System Name TLVsystem-name
DCBXP TLVsdcbxp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2650
L Commandslldp
Page 2795
lldp dcbx version autolldp dcbx version auto
Syntax Description
Configure LLDP parameterslldp
Configure DCBX parametersdcbx
Change the DCBX protocol versionversion
Auto-detect the DCBX versionauto
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether/exec/configure/if-eth-base /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2651
L Commandslldp dcbx version auto
Page 2796
lldp dcbx version cee[no] lldp dcbx version { cee | ieee }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure LLDP parameterslldp
Configure DCBX parametersdcbx
Change the DCBX protocol versionversion
The CEE version of DCBXcee
The IEEE 802.1 version of DCBXieee
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether/exec/configure/if-eth-base /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2652
L Commandslldp dcbx version cee
Page 2797
lldp eee rx_wake_time[no] lldp eee { rx_wake_time <i0> | tx_wake_time <i1> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure LLDP parameterslldp
Configure LLDP EEE parameterseee
Specify the EEE rx wake timerx_wake_time
EEE rx wake timei0
Specify the EEE tx wake timetx_wake_time
EEE tx wake timei1
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether/exec/configure/if-eth-base /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2653
L Commandslldp eee rx_wake_time
Page 2798
lldp receive[no] lldp receive
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Interface LLDP parameterslldp
Enable LLDP reception on interfacereceive
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether/exec/configure/if-eth-base /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2654
L Commandslldp receive
Page 2799
lldp tlv-select eee[no] lldp tlv-select eee
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Interface LLDP parameterslldp
Configure EEE parametertlv-select
Enable/Disable LLDP EEE TLVeee
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether/exec/configure/if-eth-base /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2655
L Commandslldp tlv-select eee
Page 2800
lldp tlv-select management-address v4[no] lldp tlv-select management-address { v4 | v6 }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure global LLDP parameterslldp
Selection of LLDP to sendtlv-select
Management Address TLVmanagement-address
Management Address TLV v4v4
Management Address TLV v6v6
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2656
L Commandslldp tlv-select management-address v4
Page 2801
lldp tlv-set management-address[no] lldp tlv-set management-address <ip-addr>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Interface LLDP parameterslldp
LLDP TLV configuration for interfacetlv-set
Management address to be sent in management-tlv of LLDPDU.management-address
IP address in dotted decimal format i.i.i.iip-addr
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether/exec/configure/if-eth-base /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2657
L Commandslldp tlv-set management-address
Page 2802
lldp tlv-set management-address ipv6[no] lldp tlv-set management-address <ipv6-addr> ipv6
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Interface LLDP parameterslldp
LLDP TLV configuration for interfacetlv-set
Management address to be sent in management-tlv of LLDPDU.management-address
IPV6ipv6
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether/exec/configure/if-eth-base /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2658
L Commandslldp tlv-set management-address ipv6
Page 2803
lldp tlv-set vlan[no] lldp tlv-set vlan [ <vlan-id> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Interface LLDP parameterslldp
LLDP TLV configuration for interfacetlv-set
VLAN-id whose SVI IP address should be used as management adrressin management-tlv of LLDPDU. Default is native VLAN.
vlan
(Optional) vlan-id within range of 1-4094vlan-id
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether/exec/configure/if-eth-base /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2659
L Commandslldp tlv-set vlan
Page 2804
lldp transmit[no] lldp transmit
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Interface LLDP parameterslldp
Enable LLDP transmission on interfacetransmit
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-gig-ether-all /exec/configure/if-gig-ether/exec/configure/if-eth-base /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2660
L Commandslldp transmit
Page 2805
load-balance[no] load-balance { [ method { src { ip | ip-l4port <src-protocol> range <src-x> <src-y> } | dst { ip-dst |ip-l4port <dst-protocol> range <dst-x> <dst-y> } } | buckets <num> | mask-position <mask> ] + }
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD Loadbalanceload-balance
(Optional) ITD Loadbalance methodmethod
(Optional) Source based parameterssrc
(Optional) Destination based parametersdst
(Optional) IPip
(Optional) IP and L4 portip-l4port
(Optional) Protocolsrc-protocol
(Optional) Match only packets in the range of port numbersrange
(Optional)src-x
(Optional)src-y
(Optional) IPip-dst
(Optional) Protocoldst-protocol
(Optional)dst-x
(Optional)dst-y
(Optional) Used to create the buckets for traffic distribution, and it shouldbe in powers of 2
buckets
(Optional) Loadbalance bucket numbernum
(Optional) Loadbalance mask positionmask-position
(Optional) Loadbalance mask position number range 0-31 for IPv4 and0-127 for IPv6
mask
Command Mode
• /exec/configure/itd
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2661
L Commandsload-balance
Page 2806
load-balance[no] load-balance { [ method { src { ip | ip-l4port <src-protocol> range <src-x> <src-y> } | dst { ip-dst |ip-l4port <dst-protocol> range <dst-x> <dst-y> } } | buckets <num> | mask-position <mask> ] + }
Syntax Description
(Optional) Negate a command or set its defaultsno
Loadbalanceload-balance
(Optional) Loadbalance methodmethod
(Optional) Source based parameterssrc
(Optional) Destination based parametersdst
(Optional) IPip
(Optional) IP and L4 portip-l4port
(Optional) Protocolsrc-protocol
(Optional) Match only packets in the range of port numbersrange
(Optional)src-x
(Optional)src-y
(Optional) IPip-dst
(Optional) Protocoldst-protocol
(Optional)dst-x
(Optional)dst-y
(Optional) Used to create the buckets for traffic distribution, and it shouldbe in powers of 2
buckets
(Optional) Loadbalance bucket numbernum
(Optional) Loadbalance mask positionmask-position
(Optional) Loadbalance mask position number range 0-31 for IPv4 and0-127 for IPv6
mask
Command Mode
• /exec/configure/smartc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2662
L Commandsload-balance
Page 2807
load-balance[no] load-balance { [ method { src { ip | ip-l4port <src-protocol> range <src-x> <src-y> } | dst { ip-dst |ip-l4port <dst-protocol> range <dst-x> <dst-y> } } | buckets <num> | mask-position <mask> ] + }
Syntax Description
(Optional) Negate a command or set its defaultsno
PLB Loadbalance optionsload-balance
(Optional) Loadbalance methodmethod
(Optional) Source based parameterssrc
(Optional) Destination based parametersdst
(Optional) IPip
(Optional) IP and L4 portip-l4port
(Optional) Protocolsrc-protocol
(Optional) Match only packets in the range of port numbersrange
(Optional)src-x
(Optional)src-y
(Optional) IPip-dst
(Optional) Protocoldst-protocol
(Optional)dst-x
(Optional)dst-y
(Optional) Used to create the buckets for traffic distribution, and it shouldbe in powers of 2
buckets
(Optional) Loadbalance bucket numbernum
(Optional) Loadbalance mask positionmask-position
(Optional) Loadbalance mask position number range 0-23 for IPv4 and0-127 for IPv6
mask
Command Mode
• /exec/configure/plb
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2663
L Commandsload-balance
Page 2808
load-intervalload-interval <interval> | no load-interval [ <interval1> ]
Syntax Description
Negate a command or set its defaultsno
Specify interval for load calculation for an interfaceload-interval
Load interval delay in secondsinterval
(Optional) Load interval delay in secondsinterval1
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2664
L Commandsload-interval
Page 2809
load-intervalload-interval <interval> | no load-interval [ <interval1> ]
Syntax Description
Negate a command or set its defaultsno
Specify interval for load calculation for an interfaceload-interval
Load interval delay in secondsinterval
(Optional) Load interval delay in secondsinterval1
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2665
L Commandsload-interval
Page 2810
load-interval counterload-interval counter <counter_val> <interval> | no load-interval counter <counter_val> [ <interval1> ]
Syntax Description
Negate a command or set its defaultsno
Specify interval for load calculation for an interfaceload-interval
Specify counter for this load intervalcounter
Load interval delay in secondsinterval
Specify counter for this load intervalcounter_val
(Optional) Load interval delay in secondsinterval1
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2666
L Commandsload-interval counter
Page 2811
load-interval counterload-interval counter <counter_val> <interval> | no load-interval counter <counter_val> [ <interval1> ]
Syntax Description
Negate a command or set its defaultsno
Specify interval for load calculation for an interfaceload-interval
Specify counter for this load intervalcounter
Specify counter for this load intervalcounter_val
Load interval delay in secondsinterval
(Optional) Load interval delay in secondsinterval1
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2667
L Commandsload-interval counter
Page 2812
loadload <uri0>
Syntax Description
Load system imageload
Enter image URIuri0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2668
L Commandsload
Page 2813
loadload <uri0> [ <s0> ]
Syntax Description
Load system imageload
Enter image URIuri0
(Optional) Optionss0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2669
L Commandsload
Page 2814
loadload <uri0> [ <s0> ]
Syntax Description
Load system imageload
Enter image URIuri0
(Optional) Optionss0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2670
L Commandsload
Page 2815
loadload <uri0> [ <s0> ]
Syntax Description
Load system imageload
Enter image URIuri0
(Optional) Optionss0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2671
L Commandsload
Page 2816
local-as{ local-as <asn> [ no-prepend [ replace-as [ dual-as ] ] ] } | { { no | default } local-as [ <asn> ] }
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Specify the local-as number for the eBGP neighborlocal-as
Autonomous System Numberasn
(Optional) Do not prepend the local-as number to updates from the eBGPneighbor
no-prepend
(Optional) Prepend only the local-as number to updates to eBGPneighbor
replace-as
(Optional) Connect using either the local-as number or the real asdual-as
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2672
L Commandslocal-as
Page 2817
local-aslocal-as <asn> | no local-as [ <asn> ]
Syntax Description
Negate a command or set its defaultsno
Specify the local-as for this vrflocal-as
AS numberasn
Command Mode
• /exec/configure/router-bgp/router-bgp-vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2673
L Commandslocal-as
Page 2818
local-label prefix[no] { [ vrf { <vrf-name> | <vrf-known-name> } ] local-label <static-inlabel> prefix { <prefix> <mask> |<prefix-mask> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) VPN Routing/Forwarding instance namevrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Configure local label assignment and forwardinglocal-label
Label Valuestatic-inlabel
For a given prefixprefix
Destination prefixprefix
Destination prefix maskmask
Destination prefix/maskprefix-mask
Command Mode
• /exec/configure/mpls_static/ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2674
L Commandslocal-label prefix
Page 2819
local-label prefix[no] { [ vrf { <vrf-name> | <vrf-known-name> } ] local-label <static-inlabel> prefix { <ipv6-prefix-mask> }}
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) VPN Routing/Forwarding instance namevrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Configure local label assignment and forwardinglocal-label
Label Valuestatic-inlabel
For a given prefixprefix
Command Mode
• /exec/configure/mpls_static/ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2675
L Commandslocal-label prefix
Page 2820
locator-led[no] locator-led { chassis | module <module> | fan <fan_num> }
Syntax Description
(Optional) Negate a command or set its defaultsno
blink locator led on devicelocator-led
blink chassis ledchassis
blink module ledmodule
please enter the module numbermodule
blink Fan ledfan
fan numberfan_num
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2676
L Commandslocator-led
Page 2821
lockdown[no] lockdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Lockdown the LSP--disable reoptimizationlockdown
Command Mode
• /exec/configure/te/lsp-attr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2677
L Commandslockdown
Page 2822
log-adjacency-changes[no] log-adjacency-changes [ detail ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Log changes in adjacency statelog-adjacency-changes
(Optional) Notify all state changesdetail
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2678
L Commandslog-adjacency-changes
Page 2823
log-adjacency-changes[no] log-adjacency-changes
Syntax Description
(Optional) Negate a command or set its defaultsno
Log changes in adjacency statelog-adjacency-changes
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2679
L Commandslog-adjacency-changes
Page 2824
log-adjacency-changes{ [ no ] log-adjacency-changes } | { [ no ] [ eigrp ] log-neighbor-changes }
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) EIGRP router configuration commandseigrp
Log changes in adjacency statelog-adjacency-changes
Enable/Disable IP-EIGRP neighbor logginglog-neighbor-changes
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2680
L Commandslog-adjacency-changes
Page 2825
log-adjacency-changes[no] log-adjacency-changes [ detail ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Log changes in adjacency statelog-adjacency-changes
(Optional) Notify all state changesdetail
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2681
L Commandslog-adjacency-changes
Page 2826
log-adjacency-changes[no] log-adjacency-changes
Syntax Description
(Optional) Negate a command or set its defaultsno
Log changes in adjacency statelog-adjacency-changes
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2682
L Commandslog-adjacency-changes
Page 2827
log-adjacency-changes[no] log-adjacency-changes
Syntax Description
(Optional) Negate a command or set its defaultsno
Log changes in adjacency statelog-adjacency-changes
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2683
L Commandslog-adjacency-changes
Page 2828
log-event-type[no] [ eigrp ] log-event-type [ dual ] [ xmit ] [ transport ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) EIGRP router configuration commandseigrp
Set event types loggedlog-event-type
(Optional) Log DUAL eventsdual
(Optional) Log transmission eventsxmit
(Optional) Log transport eventstransport
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2684
L Commandslog-event-type
Page 2829
log-neighbor-changes[no] log-neighbor-changes
Syntax Description
(Optional) Negate a command or set its defaultsno
Log a message for neighbor up/down eventlog-neighbor-changes
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2685
L Commandslog-neighbor-changes
Page 2830
log-neighbor-changes[ no | default ] log-neighbor-changes [ disable ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Log message for neighbor up/down eventlog-neighbor-changes
(Optional) Disable logging of neighbor up/down eventdisable
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2686
L Commandslog-neighbor-changes
Page 2831
log-neighbor-warnings{ { [ eigrp ] log-neighbor-warnings [ <interval> ] } | { no [ eigrp ] log-neighbor-warnings [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
(Optional) EIGRP router configuration commandseigrp
Enable/Disable IP-EIGRP neighbor warningslog-neighbor-warnings
(Optional) Neighbor warning interval in secondsinterval
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2687
L Commandslog-neighbor-warnings
Page 2832
logging[no] logging { neighbor-changes |
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable LDP logginglogging
Log LDP neighbor state changesneighbor-changes
Command Mode
• /exec/configure/ldp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2688
L Commandslogging
Page 2833
logging[no] logging { lsp { path-errors | preemption | reservation-errors | setups | teardowns } | tunnel { lsp-selection| path change } } | logging { lsp { path-errors | preemption | reservation-errors | setups | teardowns } | tunnel{ lsp-selection | path change } }
Syntax Description
Negate a command or set its defaultsno
Trap logging configurationlogging
LSP-specific traps logging configurationlsp
Log LSP Path Error trapspath-errors
Log LSP Preemption trapspreemption
Log LSP Reservation Error trapsreservation-errors
Log LSP Establishment Trapssetups
Log LSP Teardown Trapsteardowns
Tunnel-specific traps logging configurationtunnel
Log Tunnel LSP Selection trapslsp-selection
Log Tunnel Path-related trapspath
Log Tunnel Path change trapschange
Command Mode
• /exec/configure/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2689
L Commandslogging
Page 2834
logging abortlogging abort
Syntax Description
Modify message logging facilitieslogging
Flushes cached data without committing and releases the lockabort
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2690
L Commandslogging abort
Page 2835
logging console[no] logging console [ <i0> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Set console loggingconsole
(Optional) 0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2691
L Commandslogging console
Page 2836
logging debuglogging debug
Syntax Description
Exec logging commandslogging
Debug loggingdebug
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2692
L Commandslogging debug
Page 2837
logging distribute[no] logging distribute
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Enables/disables fabric distribution using cfs.distribute
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2693
L Commandslogging distribute
Page 2838
logging drop threshold[no] logging drop { threshold-packets <threshold-in-packets> | threshold-bytes <threshold-in-bytes> } [ level<level-value> ]
Syntax Description
Negate a command or set its defaultsno
set logging for copp classlogging
logging for copp dropsdrop
threshold value for dropped packetsthreshold-packets
threshold value for dropped bytesthreshold-bytes
(Optional) syslog levellevel
(Optional) specify the logging level between 1-7level-value
Command Mode
• /exec/configure/pmap/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2694
L Commandslogging drop threshold
Page 2839
logging drop thresholdlogging drop { threshold-packets <threshold-in-packets> | threshold-bytes <threshold-in-bytes> } [ level<level-value> ]
Syntax Description
set logging for copp classlogging
logging for copp dropsdrop
threshold value for dropped packetsthreshold-packets
threshold value for dropped bytesthreshold-bytes
(Optional) syslog levellevel
(Optional) specify the logging level between 1-7level-value
Command Mode
• /exec/configure/pmap/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2695
L Commandslogging drop threshold
Page 2840
logging event link enable[no] logging event { link-status | trunk-status } { enable | default }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure logging for interfacelogging
Interface eventsevent
UPDOWN and CHANGE messageslink-status
TRUNK status messagestrunk-status
To enable logging overriding port level configurationenable
default logging configuration used by interfaces not explicitly configureddefault
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2696
L Commandslogging event link enable
Page 2841
logging event port link-statuslogging event port link-status [ default ] | no logging event port link-status
Syntax Description
Negate a command or set its defaultsno
Configure logging for interfacelogging
Interface eventsevent
Port level eventsport
UPDOWN and CHANGE messageslink-status
(Optional) Use the global default valuedefault
Command Mode
• /exec/configure/if-ether-sub /exec/configure/if-port-channel-sub /exec/configure/if-gig-ether-sub/exec/configure/if-loopback /exec/configure/if-remote-ethernet-sub /exec/configure/if-ether-sub-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2697
L Commandslogging event port link-status
Page 2842
logging event port link-statuslogging event port link-status
Syntax Description
Configure logging for interfacelogging
Interface eventsevent
Port level eventsport
UPDOWN and CHANGE messageslink-status
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2698
L Commandslogging event port link-status
Page 2843
logging event port link-status[no] logging event port link-status
Syntax Description
Negate a command or set its defaultsno
Configure logging for interfacelogging
Interface eventsevent
Port level eventsport
UPDOWN and CHANGE messageslink-status
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2699
L Commandslogging event port link-status
Page 2844
logging event port link-status defaultlogging event port link-status default
Syntax Description
Configure logging for interfacelogging
Interface eventsevent
Port level eventsport
UPDOWN and CHANGE messageslink-status
Use the global default valuedefault
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2700
L Commandslogging event port link-status default
Page 2845
logging event port trunk-status[no] logging event port trunk-status
Syntax Description
Negate a command or set its defaultsno
Configure logging for interfacelogging
Interface eventsevent
Port level eventsport
TRUNK status messagestrunk-status
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2701
L Commandslogging event port trunk-status
Page 2846
logging event port trunk-statuslogging event port trunk-status
Syntax Description
Configure logging for interfacelogging
Interface eventsevent
Port level eventsport
TRUNK status messagestrunk-status
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2702
L Commandslogging event port trunk-status
Page 2847
logging event port trunk-status defaultlogging event port trunk-status default
Syntax Description
Configure logging for interfacelogging
Interface eventsevent
Port level eventsport
TRUNK status messagestrunk-status
Use the global default valuedefault
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2703
L Commandslogging event port trunk-status default
Page 2848
logging flow-mod[no] logging flow-mod
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable logginglogging
Enable logging for flow-modifyflow-mod
Command Mode
• /exec/configure/openflow/switch/sub-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2704
L Commandslogging flow-mod
Page 2849
logging flow-mod[no] logging flow-mod
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable logginglogging
Enable logging for flow-modifyflow-mod
Command Mode
• /exec/configure/openflow/switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2705
L Commandslogging flow-mod
Page 2850
logging ip access-list cache[no] logging ip access-list cache { { interval <seconds> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
IP configurationip
Access-listaccess-list
loggingcache
Log-update interval (in sec)interval
Log-update interval in secondsseconds
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2706
L Commandslogging ip access-list cache
Page 2851
logging ip access-list cache entries[no] logging ip access-list cache { { entries <num_entries> } | { threshold <num_packets> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
IP configurationip
Access-listaccess-list
loggingcache
Maximum number of log entries cached in softwareentries
Number of entriesnum_entries
Log-update thresholdthreshold
Log-update threshold (number of hits)num_packets
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2707
L Commandslogging ip access-list cache entries
Page 2852
logging ip access-list detailed[no] logging ip access-list detailed
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable detailed logginglogging
configured IPip
Access-listaccess-list
Detailed ACL informationdetailed
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2708
L Commandslogging ip access-list detailed
Page 2853
logging ip access-list include sgt[no] logging ip access-list include sgt
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
IP configurationip
Access-listaccess-list
Include additional fields in syslogsinclude
Include source group tag info in syslogssgt
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2709
L Commandslogging ip access-list include sgt
Page 2854
logging level[no] logging level { port-channel <loglevel> | port_channel <loglevel> | eth_port_channel <loglevel> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for port-channel syslog messagesport-channel
Set level for port-channel syslog messagesport_channel
Set level for port-channel syslog messageseth_port_channel
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugloglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2710
L Commandslogging level
Page 2855
logging level[no] logging level { { ipv6 icmp } | icmpv6 } <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Configure IPv6 featuresipv6
ICMPv6 Commandsicmp
ICMPv6 Commandsicmpv6
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2711
L Commandslogging level
Page 2856
logging level[no] logging level { { routing ipv6 multicast } | m6rib } <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Configure routing informationrouting
Configure IPv6 featuresipv6
Set syslog filter level for MRIBmulticast
Set syslog filter level for MRIBm6rib
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2712
L Commandslogging level
Page 2857
logging level{ logging level { auth <i1> | authpriv <i2> | cron <i3> | daemon <i4> | ftp <i5> | kernel <i6> | local0 <i7> |local1 <i8> | local2 <i9> | local3 <i10> | local4 <i11> | local5 <i12> | local6 <i13> | local7 <i14> | lpr <i15>| mail <i16> | news <i17> | syslog <i18> | user <i19> | uucp <i20> } | no logging level { auth [ <i1> ] | authpriv[ <i2> ] | cron [ <i3> ] | daemon [ <i4> ] | ftp [ <i5> ] | kernel [ <i6> ] | local0 [ <i7> ] | local1 [ <i8> ] | local2[ <i9> ] | local3 [ <i10> ] | local4 [ <i11> ] | local5 [ <i12> ] | local6 [ <i13> ] | local7 [ <i14> ] | lpr [ <i15>] | mail [ <i16> ] | news [ <i17> ] | syslog [ <i18> ] | user [ <i19> ] | uucp [ <i20> ] } }
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for Authorization Systemauth
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi1
Set level for Authorization (Private) systemauthpriv
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi2
Set level for Cron/at facilitycron
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi3
Set level for System daemonsdaemon
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi4
Set level for File Transfer Systemftp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi5
Set level for kernelkernel
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi6
Set level for Local use daemonslocal0
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi7
Set level for Local use daemonslocal1
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi8
Set level for Local use daemonslocal2
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi9
Set level for Local use daemonslocal3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2713
L Commandslogging level
Page 2858
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi10
Set level for Local use daemonslocal4
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi11
Set level for Local use daemonslocal5
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi12
Set level for Local use daemonslocal6
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi13
Set level for Local use daemonslocal7
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi14
Set level for Line Printer Systemlpr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi15
Set level for Mail systemmail
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi16
Set level for USENET newsnews
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi17
Set level for Internal Syslog Messagessyslog
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi18
Set level for User Processuser
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi19
Set level for Unix-to-Unix copy systemuucp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi20
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2714
L Commandslogging level
Page 2859
logging level[no] logging level { { routing [ ip | ipv4 ] multicast } | mrib } <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Configure routing informationrouting
(Optional) Configure IP featuresip
(Optional) Configure IP featuresipv4
Set syslog filter level for MRIBmulticast
Set syslog filter level for MRIBmrib
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2715
L Commandslogging level
Page 2860
logging level[no] logging level { { otv isis } | isis_otv } <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for OTVotv
Set syslog filter level for IS-ISisis
Show OTV ISIS logging configurationisis_otv
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2716
L Commandslogging level
Page 2861
logging level[no] logging level { xml server | xmlma } <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
xml agentxml
xml agent serverserver
xml master agent. Same as combination of keywords xml serverxmlma
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2717
L Commandslogging level
Page 2862
logging level[no] logging level { { fabricpath isis } | isis_l2mp | isis_fabricpath } <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
fabricpath configurationfabricpath
Set logging level for fabricpath IS-ISisis
Set fabricpath logging configurationisis_l2mp
Set fabricpath logging configurationisis_fabricpath
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2718
L Commandslogging level
Page 2863
logging level aaalogging level aaa <i0> | no logging level aaa [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for aaa syslog messagesaaa
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2719
L Commandslogging level aaa
Page 2864
logging level aclloglogging level acllog <i0> | no logging level acllog [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for acllog syslog messagesacllog
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2720
L Commandslogging level acllog
Page 2865
logging level aclmgr[no] logging level aclmgr <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for aclmgr syslog messagesaclmgr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2721
L Commandslogging level aclmgr
Page 2866
logging level adbm[no] logging level adbm <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for adbm syslog messagesadbm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2722
L Commandslogging level adbm
Page 2867
logging level adjmgr[no] logging level adjmgr <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for Adjacency Manageradjmgr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2723
L Commandslogging level adjmgr
Page 2868
logging level all{ logging level { all <i0> } | no logging level { all [ <i0> ] } }
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for all facilitiesall
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2724
L Commandslogging level all
Page 2869
logging level amt[no] logging level amt <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for AMTamt
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2725
L Commandslogging level amt
Page 2870
logging level arp{ logging level arp <level> } | { no logging level arp [ <level> ] }
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for ARParp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2726
L Commandslogging level arp
Page 2871
logging level ascii-cfg[no] logging level ascii-cfg <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set logging level for ascii-cfgascii-cfg
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2727
L Commandslogging level ascii-cfg
Page 2872
logging level assoc_mgr[no] logging level assoc_mgr <i0> | no logging level assoc_mgr [ <i0> ]
Syntax Description
(Optional) Negate a command or set its defaultno
Show logging configuration and contents of logfilelogging
Show facility logging configurationlevel
Show Association Manager Logging Configurationassoc_mgr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2728
L Commandslogging level assoc_mgr
Page 2873
logging level backup[no] logging level { backup | flexlink } <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for Switchport Backup syslog messagesbackup
Set level for Switchport Backup syslog messagesflexlink
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2729
L Commandslogging level backup
Page 2874
logging level bfd[no] logging level bfd <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for bfd syslog messagesbfd
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2730
L Commandslogging level bfd
Page 2875
logging level bgp[no] logging level bgp <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for BGPbgp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2731
L Commandslogging level bgp
Page 2876
logging level bloggerd[no] logging level bloggerd <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for BloggerD syslog messagesbloggerd
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2732
L Commandslogging level bloggerd
Page 2877
logging level bootvar[no] logging level bootvar <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for bootvarbootvar
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2733
L Commandslogging level bootvar
Page 2878
logging level callhomelogging level callhome <i0> | no logging level callhome [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Callhome syslog levelcallhome
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2734
L Commandslogging level callhome
Page 2879
logging level capability[no] logging level capability <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog level for mig utils daemoncapability
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2735
L Commandslogging level capability
Page 2880
logging level catena[no] logging level catena <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for catena syslog messagescatena
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2736
L Commandslogging level catena
Page 2881
logging level cdplogging level cdp <i0> | no logging level cdp [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for CDP syslog messagescdp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2737
L Commandslogging level cdp
Page 2882
logging level cert[no] logging level { cert-enroll <i0> | cert_enroll <i1> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Cert-enroll syslog levelcert-enroll
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Cert-enroll syslog levelcert_enroll
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2738
L Commandslogging level cert
Page 2883
logging level cfs[no] logging level cfs <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2739
L Commandslogging level cfs
Page 2884
logging level clis[no] logging level clis <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for CLISclis
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2740
L Commandslogging level clis
Page 2885
logging level clk_mgr[no] logging level clk_mgr <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for clock manager syslog messagesclk_mgr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2741
L Commandslogging level clk_mgr
Page 2886
logging level confcheck{ logging level confcheck <i0> | no logging level confcheck [ <i0> ] }
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2742
L Commandslogging level confcheck
Page 2887
logging level copplogging level copp <i0> | no logging level copp [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for copp syslog messagescopp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2743
L Commandslogging level copp
Page 2888
logging level core{ logging level core <i0> | no logging level core [ <i0> ] }
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
core daemon syslog levelcore
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2744
L Commandslogging level core
Page 2889
logging level cts[no] logging level cts <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for cts syslog messagescts
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2745
L Commandslogging level cts
Page 2890
logging level dhclient[no] logging level dhclient <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for dhcp client syslog messagesdhclient
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2746
L Commandslogging level dhclient
Page 2891
logging level dhcp_snooplogging level dhcp_snoop <level> | no logging level dhcp_snoop [ <level> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for dhcp snoop syslog messagesdhcp_snoop
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2747
L Commandslogging level dhcp_snoop
Page 2892
logging level diagclient[no] logging level diagclient <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for GOLD DiagClient syslog messagesdiagclient
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2748
L Commandslogging level diagclient
Page 2893
logging level diagmgr[no] logging level diagmgr <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for GOLD DiagMgr syslog messagesdiagmgr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2749
L Commandslogging level diagmgr
Page 2894
logging level dot1x[no] logging level dot1x <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for dot1x syslog messagesdot1x
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2750
L Commandslogging level dot1x
Page 2895
logging level ecp[no] logging level ecp <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for ECPecp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2751
L Commandslogging level ecp
Page 2896
logging level eigrp[no] logging level eigrp [ <eigrp-ptag> ] <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for EIGRPeigrp
(Optional) Process tageigrp-ptag
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2752
L Commandslogging level eigrp
Page 2897
logging level eltmlogging level eltm <i0> | no logging level eltm
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for eltm syslog messageseltm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2753
L Commandslogging level eltm
Page 2898
logging level epp[no] logging level epp <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for EPP syslog messagesepp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2754
L Commandslogging level epp
Page 2899
logging level ethdstats[no] logging level { ethdstats <i0> | eth_dstats <i0> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
delta statistics syslog levelethdstats
delta statistics syslog leveleth_dstats
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2755
L Commandslogging level ethdstats
Page 2900
logging level ethpm[no] logging level ethpm <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for ethpm syslog messagesethpm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2756
L Commandslogging level ethpm
Page 2901
logging level ethpm link[no] logging level ethpm { link-up | link-down } <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for ethpm syslog messagesethpm
Configure logging level for link up syslog messageslink-up
Configure logging level for link down syslog messageslink-down
Logging Levellevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2757
L Commandslogging level ethpm link
Page 2902
logging level evb[no] logging level evb <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for EVBevb
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2758
L Commandslogging level evb
Page 2903
logging level evmc[no] logging level evmc <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for evmc syslog messagesevmc
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2759
L Commandslogging level evmc
Page 2904
logging level evmed[no] logging level evmed <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for evmed syslog messagesevmed
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2760
L Commandslogging level evmed
Page 2905
logging level evms[no] logging level evms <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for evms syslog messagesevms
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2761
L Commandslogging level evms
Page 2906
logging level fabric forwarding[no] logging level fabric forwarding <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Fabricfabric
Fabric Forwarding Protocol: Host Mobility Manager (HMM)forwarding
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2762
L Commandslogging level fabric forwarding
Page 2907
logging level fcoe_mgr[no] logging level fcoe_mgr <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for fcoe_mgr syslog messagesfcoe_mgr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2763
L Commandslogging level fcoe_mgr
Page 2908
logging level feature-mgr{ logging level feature-mgr <i0> | no logging level feature-mgr [ <i0> ] }
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set feature manager syslog levelfeature-mgr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2764
L Commandslogging level feature-mgr
Page 2909
logging level fs-daemon{ logging level fs-daemon <i0> | no logging level fs-daemon [ <i0> ] }
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
fs daemon syslog levelfs-daemon
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2765
L Commandslogging level fs-daemon
Page 2910
logging level gpixm[no] logging level gpixm <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for global-pixm syslog messagesgpixm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2766
L Commandslogging level gpixm
Page 2911
logging level hardware-telemetry[no] logging level hardware-telemetry <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for hardware-telemetry syslog messageshardware-telemetry
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2767
L Commandslogging level hardware-telemetry
Page 2912
logging level hsrp[no] logging level hsrp <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for hsrp syslog messageshsrp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2768
L Commandslogging level hsrp
Page 2913
logging level icam[no] logging level icam <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for icam syslog messagesicam
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2769
L Commandslogging level icam
Page 2914
logging level igmp[no] logging level [ ip ] igmp <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
(Optional) Configure IP featuresip
IGMP global configuration commandsigmp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2770
L Commandslogging level igmp
Page 2915
logging level im[no] logging level { im <i0> | ifmgr <i0> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for im syslog messagesim
Set level for im syslog messagesifmgr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2771
L Commandslogging level im
Page 2916
logging level imp[no] logging level imp <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for imp syslog messagesimp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2772
L Commandslogging level imp
Page 2917
logging level interface-vlan[no] logging level interface-vlan <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for interface vlan syslog messagesinterface-vlan
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2773
L Commandslogging level interface-vlan
Page 2918
logging level ip pim[no] logging level ip pim <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Configure IP featuresip
Set syslog filter level for PIMpim
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2774
L Commandslogging level ip pim
Page 2919
logging level ip sla responder[no] logging level ip sla responder <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
ip
Service Level Agreement (SLA)sla
Set level for sla-responder syslog messagesresponder
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2775
L Commandslogging level ip sla responder
Page 2920
logging level ip sla sender[no] logging level ip sla sender <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
ip
Service Level Agreement (SLA)sla
Set level for sla-sender syslog messagessender
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2776
L Commandslogging level ip sla sender
Page 2921
logging level ip sla twamp-server[no] logging level ip sla twamp-server <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
ip
Service Level Agreement (SLA)sla
Set level for sla-twamp-server syslog messagestwamp-server
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2777
L Commandslogging level ip sla twamp-server
Page 2922
logging level ipconf[no] logging level ipconf { ipv6 <i0> | <i1> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for ipconf syslog messagesipconf
Set level for ipconf syslog messagesipv6
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2778
L Commandslogging level ipconf
Page 2923
logging level ipfiblogging level ipfib <i0> | no logging level ipfib
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for ipfib syslog messagesipfib
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2779
L Commandslogging level ipfib
Page 2924
logging level ipqos[no] logging level { ipqos | IPQOSMGR } <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2780
L Commandslogging level ipqos
Page 2925
logging level ipv6 pim[no] logging level ipv6 pim <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Configure IPv6 featuresipv6
Set syslog filter level for PIM6pim
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2781
L Commandslogging level ipv6 pim
Page 2926
logging level iscm[no] logging level iscm <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for iscm syslog messagesiscm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2782
L Commandslogging level iscm
Page 2927
logging level iscm[no] logging level iscm <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for iscm syslog messagesiscm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2783
L Commandslogging level iscm
Page 2928
logging level isis[no] logging level isis <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for IS-ISisis
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2784
L Commandslogging level isis
Page 2929
logging level keystorelogging level { keystore | sksd } <i0> | no logging level { keystore | sksd } [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Keystore syslog levelkeystore
Keystore/sksd syslog levelsksd
i0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2785
L Commandslogging level keystore
Page 2930
logging level l2fmlogging level l2fm <i0> | no logging level l2fm
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for l2fm syslog messagesl2fm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2786
L Commandslogging level l2fm
Page 2931
logging level l2rib[no] logging level l2rib <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
l2rib syslogl2rib
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2787
L Commandslogging level l2rib
Page 2932
logging level l3vm[no] logging level l3vm <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for L3VMl3vm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2788
L Commandslogging level l3vm
Page 2933
logging level lacp[no] logging level lacp <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for lacp syslog messageslacp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2789
L Commandslogging level lacp
Page 2934
logging level ldaplogging level ldap <i0> | no logging level ldap [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for ldap syslog messagesldap
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2790
L Commandslogging level ldap
Page 2935
logging level lem-mgr[no] logging level lem-mgr <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2791
L Commandslogging level lem-mgr
Page 2936
logging level licenselogging level { license | licmgr } <i0> | no logging level { license | licmgr } [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Licensing syslog levellicense
Licensing syslog levellicmgr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2792
L Commandslogging level license
Page 2937
logging level lim[no] logging level lim <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for lim syslog messageslim
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2793
L Commandslogging level lim
Page 2938
logging level lisp[no] logging level lisp <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set logging level for LISPlisp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2794
L Commandslogging level lisp
Page 2939
logging level lldp[no] logging level lldp <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for lldp syslog messageslldp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2795
L Commandslogging level lldp
Page 2940
logging level m2rib[no] logging level m2rib <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for m2rib syslog messagesm2rib
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2796
L Commandslogging level m2rib
Page 2941
logging level mfdmlogging level mfdm <i0> | no logging level mfdm
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for mfdm syslog messagesmfdm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2797
L Commandslogging level mfdm
Page 2942
logging level mfwd[no] logging level { mfwd | mcastfwd } <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Configures Global IP Multicast Forwardingmfwd
Configures Global IP Multicast Forwardingmcastfwd
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2798
L Commandslogging level mfwd
Page 2943
logging level mmode[no] logging level mmode <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for maintenance mode syslog messagesmmode
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2799
L Commandslogging level mmode
Page 2944
logging level module[no] logging level module <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for module(linecard) manager syslog messagesmodule
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2800
L Commandslogging level module
Page 2945
logging level monitor[no] logging level monitor <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for ethernet span syslog messagesmonitor
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2801
L Commandslogging level monitor
Page 2946
logging level msdp[no] logging level [ ip ] msdp <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
(Optional) Configure IP featuresip
Set syslog filter level for MSDPmsdp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2802
L Commandslogging level msdp
Page 2947
logging level mvsh[no] logging level mvsh <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for mvsh syslog messagesmvsh
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2803
L Commandslogging level mvsh
Page 2948
logging level natlogging level nat <i0> | no logging level nat [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for NAT syslog messagesnat
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2804
L Commandslogging level nat
Page 2949
logging level nbmlogging level nbm <i0> | no logging level nbm
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for nbm syslog messagesnbm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2805
L Commandslogging level nbm
Page 2950
logging level netstack{ logging level netstack <level> } | { no logging level netstack [ <level> ] }
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for Netstacknetstack
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2806
L Commandslogging level netstack
Page 2951
logging level nfm[no] logging level nfm <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for nfm syslog messagesnfm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2807
L Commandslogging level nfm
Page 2952
logging level ngoam[no] logging level ngoam <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for oam logging messagesngoam
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure handle function sdstub_syslog sdwrap args-legacy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2808
L Commandslogging level ngoam
Page 2953
logging level npv[no] logging level npv <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for NPV syslog messagesnpv
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2809
L Commandslogging level npv
Page 2954
logging level ntp[no] logging level ntp <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for NTPntp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2810
L Commandslogging level ntp
Page 2955
logging level nxsdk[no] logging level nxsdk <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
NXOS SDKnxsdk
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2811
L Commandslogging level nxsdk
Page 2956
logging level openflow[no] logging level openflow <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for OpenFlow agent syslog messagesopenflow
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2812
L Commandslogging level openflow
Page 2957
logging level orib[no] logging level orib <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for ORIBorib
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2813
L Commandslogging level orib
Page 2958
logging level ospf[no] logging level ospf <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for OSPFospf
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2814
L Commandslogging level ospf
Page 2959
logging level ospfv3[no] logging level ospfv3 <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for OSPFv3ospfv3
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2815
L Commandslogging level ospfv3
Page 2960
logging level pfstatlogging level pfstat <i0> | no logging level pfstat
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for pfstat syslog messagespfstat
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2816
L Commandslogging level pfstat
Page 2961
logging level pixm[no] logging level pixm <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for vdc-local-pixm syslog messagespixm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2817
L Commandslogging level pixm
Page 2962
logging level pktmgr[no] logging level pktmgr <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for Packet managerpktmgr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2818
L Commandslogging level pktmgr
Page 2963
logging level platform[no] logging level platform <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
platform manager syslog levelplatform
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2819
L Commandslogging level platform
Page 2964
logging level plbm[no] logging level plbm <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for plbm syslog messagesplbm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2820
L Commandslogging level plbm
Page 2965
logging level plcmgr[no] logging level { plcmgr | ipplc } <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2821
L Commandslogging level plcmgr
Page 2966
logging level pltfm_config[no] logging level pltfm_config <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for pltfm_config syslog messagespltfm_config
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2822
L Commandslogging level pltfm_config
Page 2967
logging level plugin{ logging level plugin <i0> | no logging level plugin [ <i0> ] }
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for plugin syslog messagesplugin
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2823
L Commandslogging level plugin
Page 2968
logging level poap[no] logging level poap <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for poap syslog messagespoap
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2824
L Commandslogging level poap
Page 2969
logging level poed[no] logging level poed <i0> | no logging level poed [ <i0> ]
Syntax Description
(Optional) Negate a command or set its defaultno
Show logging configuration and contents of logfilelogging
Show facility logging configurationlevel
Show PoE Daemon Logging Configurationpoed
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2825
L Commandslogging level poed
Page 2970
logging level port-profilelogging level port-profile <i0> | no logging level port-profile [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for port-profile syslog messagesport-profile
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2826
L Commandslogging level port-profile
Page 2971
logging level port-resources[no] logging level port-resources <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for prm syslog messagesport-resources
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2827
L Commandslogging level port-resources
Page 2972
logging level port-securitylogging level port-security <i0> | no logging level port-security [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for port-security syslog messagesport-security
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2828
L Commandslogging level port-security
Page 2973
logging level port[no] logging level port <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for port syslog messagesport
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2829
L Commandslogging level port
Page 2974
logging level port_client[no] logging level port_client <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for port_client syslog messagesport_client
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2830
L Commandslogging level port_client
Page 2975
logging level port_lb[no] logging level { port_lb <i0> | diag_port_lb <i0> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for Diagnostic Port Loopback Test syslog messagesport_lb
Set level for Diagnostic Port Loopback Test syslog messagesdiag_port_lb
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2831
L Commandslogging level port_lb
Page 2976
logging level port link-failure[no] logging level port link-failure <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for port syslog messagesport
Configure logging level for link failure syslog messageslink-failure
Logging Levellevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2832
L Commandslogging level port link-failure
Page 2977
logging level private-vlan[no] logging level private-vlan <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for private VLAN syslog messagesprivate-vlan
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2833
L Commandslogging level private-vlan
Page 2978
logging level ptp[no] logging level ptp <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for ptp syslog messagesptp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2834
L Commandslogging level ptp
Page 2979
logging level radiuslogging level radius <i0> | no logging level radius [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
RADIUS syslog levelradius
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2835
L Commandslogging level radius
Page 2980
logging level res_mgr[no] logging level res_mgr <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for res_mgr syslog messagesres_mgr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2836
L Commandslogging level res_mgr
Page 2981
logging level rip[no] logging level rip <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for RIPrip
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2837
L Commandslogging level rip
Page 2982
logging level rpm[no] logging level rpm <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for RPMrpm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2838
L Commandslogging level rpm
Page 2983
logging level rsvp[no] logging level rsvp <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for RSVP syslog messagesrsvp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2839
L Commandslogging level rsvp
Page 2984
logging level sal[no] logging level sal <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for sal syslog messagessal
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2840
L Commandslogging level sal
Page 2985
logging level san[no] logging level { san-port-channel <loglevel> | port_channel <loglevel> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for san-port-channel syslog messagessan-port-channel
Set level for san-port-channel syslog messagesport_channel
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugloglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2841
L Commandslogging level san
Page 2986
logging level scheduler[no] logging level scheduler <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set logging level for schedulerscheduler
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2842
L Commandslogging level scheduler
Page 2987
logging level securitylogging level { security | securityd } <i0> | no logging level { security | securityd } [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Security syslog levelsecurity
Security syslog levelsecurityd
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2843
L Commandslogging level security
Page 2988
logging level session-mgrlogging level session-mgr <i0> | no logging level session-mgr [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for session-manager syslog messagessession-mgr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2844
L Commandslogging level session-mgr
Page 2989
logging level sflow[no] logging level sflow <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for sFlow syslog messagessflow
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2845
L Commandslogging level sflow
Page 2990
logging level smartc[no] logging level smartc <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for smartc syslog messagessmartc
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2846
L Commandslogging level smartc
Page 2991
logging level smm[no] logging level smm <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set logging level for Shared Memory Managersmm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2847
L Commandslogging level smm
Page 2992
logging level snmpd[no] logging level snmpd <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for SNMP syslog messagessnmpd
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2848
L Commandslogging level snmpd
Page 2993
logging level snmpmib_proc[no] logging level snmpmib_proc <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for snmpmib_proc syslog messagessnmpmib_proc
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2849
L Commandslogging level snmpmib_proc
Page 2994
logging level spanning[no] logging level { spanning-tree } <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for stp syslog messagesspanning-tree
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2850
L Commandslogging level spanning
Page 2995
logging level spm[no] logging level spm <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for spm syslog messagesspm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2851
L Commandslogging level spm
Page 2996
logging level stripcl[no] logging level stripcl <log-level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for stripcl syslog messagesstripcl
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglog-level
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2852
L Commandslogging level stripcl
Page 2997
logging level sysmgr{ logging level sysmgr <i0> | no logging level sysmgr [ <i0> ] }
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2853
L Commandslogging level sysmgr
Page 2998
logging level tacacslogging level tacacs <i0> | no logging level tacacs [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
TACACS+ syslog leveltacacs
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2854
L Commandslogging level tacacs
Page 2999
logging level tamnw[no] logging level tamnw <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for tamnw syslog messagestamnw
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2855
L Commandslogging level tamnw
Page 3000
logging level track[no] logging level track <i0>
Syntax Description
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for track syslog messagestrack
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2856
L Commandslogging level track
Page 3001
logging level tunnellogging level tunnel <i0> | no logging level tunnel [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for tunnel syslog messagestunnel
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2857
L Commandslogging level tunnel
Page 3002
logging level u2rib[no] logging level u2rib <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for u2rib syslog messagesu2rib
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2858
L Commandslogging level u2rib
Page 3003
logging level u6rib[no] logging level u6rib <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for U6RIBu6rib
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2859
L Commandslogging level u6rib
Page 3004
logging level udld[no] logging level udld <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for udld syslog messagesudld
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2860
L Commandslogging level udld
Page 3005
logging level ufdm[no] logging level ufdm <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for ufdm syslog messagesufdm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2861
L Commandslogging level ufdm
Page 3006
logging level urib[no] logging level urib <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set syslog filter level for URIBurib
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2862
L Commandslogging level urib
Page 3007
logging level vdc_mgr[no] logging level vdc_mgr <i0>
Syntax Description
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for vdc_mgr syslog messagesvdc_mgr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2863
L Commandslogging level vdc_mgr
Page 3008
logging level virtual-service[no] logging level virtual-service <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for virtual service syslog messagesvirtual-service
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2864
L Commandslogging level virtual-service
Page 3009
logging level vlan_mgrlogging level vlan_mgr <i0> | no logging level vlan_mgr [ <i0> ]
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for VLAN syslog messagesvlan_mgr
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2865
L Commandslogging level vlan_mgr
Page 3010
logging level vmm[no] logging level vmm <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for vmm syslog messagesvmm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2866
L Commandslogging level vmm
Page 3011
logging level vmtracker[no] logging level vmtracker <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for vmtracker syslog messagesvmtracker
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2867
L Commandslogging level vmtracker
Page 3012
logging level vpc[no] logging level vpc <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for vPC syslog messagesvpc
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2868
L Commandslogging level vpc
Page 3013
logging level vrrp[no] logging level { vrrp-cfg <cfg_level_num> | vrrp-eng <eng_level_num> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for vrrp configurationvrrp-cfg
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugcfg_level_num
Set level for vrrp enginevrrp-eng
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugeng_level_num
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2869
L Commandslogging level vrrp
Page 3014
logging level vrrpv3[no] logging level { vrrpv3 <level> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for vrrpv3 configurationvrrpv3
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debuglevel
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2870
L Commandslogging level vrrpv3
Page 3015
logging level vsan{ logging level vsan <i0> | no logging level vsan [ <i1> ] }
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
(Optional) 0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2871
L Commandslogging level vsan
Page 3016
logging level vshd[no] logging level vshd <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2872
L Commandslogging level vshd
Page 3017
logging level vtp[no] logging level vtp <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set level for vtp syslog messagesvtp
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2873
L Commandslogging level vtp
Page 3018
logging level wwnm[no] logging level wwnm <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
Set WWN Manager syslog levelwwnm
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2874
L Commandslogging level wwnm
Page 3019
logging level xbar[no] logging level xbar <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Facility parameter for syslog messageslevel
xbar syslog levelxbar
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2875
L Commandslogging level xbar
Page 3020
logging logfile{ logging logfile <s0> <i0> [ size <i1> ] | no logging logfile [ <s0> <i0> [ size <i1> ] ] }
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Set File logginglogfile
Enter the logfile names0
0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
(Optional) Set logfile sizesize
(Optional) Enter the logfile size in bytesi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2876
L Commandslogging logfile
Page 3021
logging message interface type ethernetlogging message interface type ethernet <info> | no logging message interface type ethernet <info>
Syntax Description
Negate a command or set its defaultsno
Configure logging for interfacelogging
Interface eventsmessage
Interface level eventsinterface
Interface typetype
Ethernet interfacesethernet
Field Names to be added to interface sysloginfo
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2877
L Commandslogging message interface type ethernet
Page 3022
logging module[no] logging module [ <i0> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Set module(linecard) loggingmodule
(Optional) 0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2878
L Commandslogging module
Page 3023
logging monitor[no] logging monitor [ <i0> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Set terminal line(monitor) logging levelmonitor
(Optional) 0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2879
L Commandslogging monitor
Page 3024
logging origin-id[no] logging origin-id { hostname | ip <ip0> | string <s0> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Enable origin information for Remote Syslog Serverorigin-id
Use hostname as origin-id of logging messageshostname
Use ip address as origin-id of logging messagesip
Hostname/IPv4/IPv6 addressip0
Use text string as origin-id of logging messagesstring
Enter string to append to the front of syslog msgss0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2880
L Commandslogging origin-id
Page 3025
logging rate-limit[no] logging rate-limit
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Enables rate limit for log messagesrate-limit
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2881
L Commandslogging rate-limit
Page 3026
logging server[no] logging server <host0> [ [ <i1> ] [ port <port> ] [ secure [ trustpoint client-identity <trustpoint-label> ]] [ use-vrf { <vrf-name> | <vrf-known-name> } | facility { auth | authpriv | cron | daemon | ftp | kernel | local0| local1 | local2 | local3 | local4 | local5 | local6 | local7 | lpr | mail | news | syslog | user | uucp } ] + ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Enable forwarding to Remote Syslog Serverserver
Hostname/IPv4/IPv6 address of the Remote Syslog Serverhost0
(Optional) 0-emerg 1-alert 2-crit 3-err 4-warn 5-notif 6-inform 7-debugi1
(Optional) Destination Port when forwarding to remote serverport
(Optional) Range from 1 - 65535(Default 514)port
(Optional) Enable secure connection to remote serversecure
(Optional) Trustpoint configurationtrustpoint
(Optional) Client Identity certificate for mutual authenticationclient-identity
(Optional) trustpoint to use for client certificate authenticationtrustpoint-label
(Optional) Display per-VRF informationuse-vrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Facility to use when forwarding to serverfacility
(Optional) Use auth facilityauth
(Optional) Use authpriv facilityauthpriv
(Optional) Use Cron/at facilitycron
(Optional) Use daemon facilitydaemon
(Optional) Use file transfer system facilityftp
(Optional) Use kernel facilitykernel
(Optional) Use local0 facilitylocal0
(Optional) Use local1 facilitylocal1
(Optional) Use local2 facilitylocal2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2882
L Commandslogging server
Page 3027
(Optional) Use local3 facilitylocal3
(Optional) Use local4 facilitylocal4
(Optional) Use local5 facilitylocal5
(Optional) Use local6 facilitylocal6
(Optional) Use local7 facilitylocal7
(Optional) Use lpr facilitylpr
(Optional) Use mail facilitymail
(Optional) Use USENET news facilitynews
(Optional) Use syslog facilitysyslog
(Optional) Use user facilityuser
(Optional) Use Unix-to-Unix copy system facilityuucp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2883
L Commandslogging server
Page 3028
logging server dns-refresh-interval[no] logging server dns-refresh-interval <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Enable forwarding to Remote Syslog Serverserver
DNS refresh interval for remote syslog server hostnamesdns-refresh-interval
Configure DNSRefresh interval from 10minutes to 24 hours Default:60(will cancel any existing timers)
i0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2884
L Commandslogging server dns-refresh-interval
Page 3029
logging source-interface{ logging source-interface <interface> | no logging source-interface }
Syntax Description
Negate a command or set its defaultsno
Modify message logging facilitieslogging
Enable Source-Interface for Remote Syslog Serversource-interface
Source interface nameinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2885
L Commandslogging source-interface
Page 3030
logging timestamp[no] logging timestamp { microseconds | milliseconds | seconds }
Syntax Description
(Optional) Negate a command or set its defaultsno
Modify message logging facilitieslogging
Set logging timestamp granularitytimestamp
Timestamp in micro-secondsmicroseconds
Timestamp in milli-secondsmilliseconds
Timestamp in seconds (Default)seconds
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2886
L Commandslogging timestamp
Page 3031
login on-failure log[no] login on-failure log
Syntax Description
(Optional) Negate a command or set its defaultsno
loginlogin
Set options for failed login attempton-failure
Generate syslogs on failure loginslog
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2887
L Commandslogin on-failure log
Page 3032
login on-success log[no] login on-success log
Syntax Description
(Optional) Negate a command or set its defaultsno
loginlogin
Set options for successful login attempton-success
Generate syslogs on successful loginslog
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2888
L Commandslogin on-success log
Page 3033
logout-warning{ logout-warning <i0> | no logout-warning [ <i0> ] }
Syntax Description
Negate a command or set its defaultsno
Configure logout warninglogout-warning
Enter logout warning time in secondsi0
Command Mode
• /exec/configure/line
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2889
L Commandslogout-warning
Page 3034
low-memory exempt[ no | default ] low-memory exempt
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Behaviourlow-memory
Doexempt
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2890
L Commandslow-memory exempt
Page 3035
lshowlshow
Syntax Description
display this instance of credentiallshow
Command Mode
• /exec/configure/dot1x-cred
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2891
L Commandslshow
Page 3036
lshowlshow
Syntax Description
local show: displays config of current interfacelshow
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2892
L Commandslshow
Page 3037
lsp-gen-intervallsp-gen-interval <max-wait> [ <initial-wait> <second-wait> ] | no lsp-gen-interval <max-wait> [ <initial-wait><second-wait> ]
Syntax Description
Negate a command or set its defaultsno
Configure LSP generation intervallsp-gen-interval
Maximum wait between trigger and LSP generation (milli-secs)max-wait
(Optional) Initial wait between trigger and LSP generation (milli-secs)initial-wait
(Optional) Second wait used in LSP generation (milli-secs) duringbackoff
second-wait
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2893
L Commandslsp-gen-interval
Page 3038
lsp-gen-intervallsp-gen-interval <level> <max-wait> [ <initial-wait> <second-wait> ] | no lsp-gen-interval <level> <max-wait>[ <initial-wait> <second-wait> ]
Syntax Description
Negate a command or set its defaultsno
Configure LSP generation intervallsp-gen-interval
IS-IS levellevel
Maximum wait between trigger and LSP generation (milli-secs)max-wait
(Optional) Initial wait between trigger and LSP generation (milli-secs)initial-wait
(Optional) Second wait used in LSP generation (milli-secs) duringbackoff
second-wait
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2894
L Commandslsp-gen-interval
Page 3039
lsp-gen-intervallsp-gen-interval <max-wait> [ <initial-wait> <second-wait> ] | no lsp-gen-interval <max-wait> [ <initial-wait><second-wait> ]
Syntax Description
Negate a command or set its defaultsno
Configure LSP generation intervallsp-gen-interval
Maximum wait between trigger and LSP generation (milli-secs)max-wait
(Optional) Initial wait between trigger and LSP generation (milli-secs)initial-wait
(Optional) Second wait used in LSP generation (milli-secs) duringbackoff
second-wait
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2895
L Commandslsp-gen-interval
Page 3040
lsp-mtulsp-mtu <mtu> | no lsp-mtu [ <mtu> ]
Syntax Description
Negate a command or set its defaultsno
Set LSP MTUlsp-mtu
Maximum LSP size in bytesmtu
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2896
L Commandslsp-mtu
Page 3041
lsp-mtulsp-mtu <mtu> | no lsp-mtu [ <mtu> ]
Syntax Description
Negate a command or set its defaultsno
Set LSP MTUlsp-mtu
Maximum LSP size in bytesmtu
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2897
L Commandslsp-mtu
Page 3042
lsp-mtulsp-mtu <mtu> | no lsp-mtu [ <mtu> ]
Syntax Description
Negate a command or set its defaultsno
Set LSP MTUlsp-mtu
Maximum LSP size in bytesmtu
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2898
L Commandslsp-mtu
Page 3043
lsp[no] lsp <lsp-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure the name for the label-switched pathlsp
Name for this LSPlsp-name
Command Mode
• /exec/configure/mpls_static/ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2899
L Commandslsp
Page 3044
lsp[no] lsp <lsp-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure the name for the label-switched pathlsp
Name for this LSPlsp-name
Command Mode
• /exec/configure/mpls_static/ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2900
L Commandslsp
Page 3045
lsp attributes[no] lsp attributes <name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure LSP parameterslsp
Configure LSP attributesattributes
Name of LSP attribute listname
Command Mode
• /exec/configure/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2901
L Commandslsp attributes
Page 3046
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2902
L Commandslsp attributes
Page 3047
M Commands
• m2rib debug ftag, on page 2908• m2rib debug gr-route add nh, on page 2909• m2rib debug log-size event-history, on page 2911• m2rib debug log-size transactions, on page 2912• m2rib debug omf enable, on page 2913• m2rib debug pkt-recv enable, on page 2914• m2rib debug swroute nh, on page 2915• m2rib debug topo, on page 2916• m2rib debug topo loop-flush-timeout, on page 2917• mac-addr, on page 2918• mac-address, on page 2919• mac-address, on page 2920• mac-address, on page 2921• mac-address bpdu source version 2, on page 2922• mac-address destination, on page 2923• mac-address ipv6-extract, on page 2924• mac-learn disable, on page 2925• mac-learn disable, on page 2926• mac-list permit, on page 2927• mac access-list, on page 2928• mac address-table aging-time, on page 2929• mac address-table guard-vpc-peergw-mac, on page 2930• mac address-table limit system, on page 2931• mac address-table loop-detect port-down, on page 2932• mac address-table multicast vlan interface, on page 2933• mac address-table notification mac-move, on page 2934• mac address-table notification threshold, on page 2935• mac address-table static vlan interface, on page 2936• mac address-table static vni, on page 2937• mac address, on page 2938• mac address inherit, on page 2939• mac advert interval, on page 2940• mac packet-classify, on page 2941
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2903
Page 3048
• mac packet-classify, on page 2942• mac port access-group, on page 2943• managed-config-flag, on page 2944• management, on page 2945• map-notify-group, on page 2946• map-server key, on page 2947• marker-packet-n3500, on page 2948• marker-packet, on page 2949• master ipv4, on page 2950• match-address, on page 2951• match, on page 2952• match, on page 2954• match, on page 2955• match access-group name, on page 2959• match address, on page 2960• match as-number, on page 2961• match as-number as-path-list, on page 2962• match as-path, on page 2963• match class-map, on page 2964• match community, on page 2965• match cos, on page 2966• match cos, on page 2967• match datalink, on page 2968• match datalink, on page 2969• match dscp, on page 2970• match dscp, on page 2971• match exception, on page 2972• match extcommunity, on page 2973• match interface, on page 2974• match ip address, on page 2975• match ip address prefix-list, on page 2976• match ip multicast rp, on page 2977• match ip next-hop prefix-list, on page 2978• match ip protocol, on page 2979• match ip route-source prefix-list, on page 2980• match ipv4 protocol, on page 2981• match ipv4 source address, on page 2982• match ipv4 source address, on page 2983• match ipv4 transport destination, on page 2984• match ipv6, on page 2985• match ipv6, on page 2986• match ipv6 address, on page 2987• match ipv6 address prefix-list, on page 2988• match ipv6 multicast rp, on page 2989• match ipv6 next-hop prefix-list, on page 2990• match ipv6 protocol, on page 2991
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2904
M Commands
Page 3049
• match ipv6 route-source prefix-list, on page 2992• match ipv6 transport destination, on page 2993• match metric, on page 2994• match ospf-area, on page 2995• match protocol, on page 2996• match protocol arp, on page 2997• match qos-group, on page 2998• match qos-group2, on page 2999• match qos-group2, on page 3000• match qos-group, on page 3001• match redirect, on page 3002• match route-type, on page 3003• match source-protocol, on page 3004• match tag, on page 3005• match transport destination, on page 3006• max-backoff, on page 3007• max-backoff, on page 3008• max-lsa, on page 3009• max-lsa, on page 3010• max-lsp-lifetime, on page 3011• max-lsp-lifetime, on page 3012• max-lsp-lifetime, on page 3013• max-metric router-lsa, on page 3014• max-metric router-lsa, on page 3015• max-ports, on page 3016• max-ports, on page 3017• maxas-limit, on page 3018• maximum-paths, on page 3019• maximum-paths, on page 3020• maximum-paths, on page 3021• maximum-paths, on page 3022• maximum-paths, on page 3023• maximum-paths, on page 3024• maximum-paths, on page 3025• maximum-paths, on page 3026• maximum-paths eibgp, on page 3027• maximum-paths mixed, on page 3028• maximum-peers, on page 3029• maximum-prefix, on page 3030• maximum-prefix, on page 3031• maximum-prefix, on page 3032• maximum routes, on page 3033• mdix auto, on page 3034• mdt asm-use-shared-tree, on page 3035• mdt data, on page 3036• mdt data bidir-enable, on page 3037
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2905
M Commands
Page 3050
• mdt default, on page 3038• mdt enforce-bgp-mdt-safi, on page 3039• mdt mtu, on page 3040• mdt pim hello-interval, on page 3041• mdt pim jp-interval, on page 3042• mdt source, on page 3043• media-type auto, on page 3044• media-type rj45, on page 3045• media-type sfp, on page 3046• media, on page 3047• medium, on page 3048• medium broadcast, on page 3049• medium broadcast, on page 3050• medium p2p, on page 3051• medium p2p, on page 3052• member vlan, on page 3053• member vni, on page 3054• member vni, on page 3055• member vni associate-vrf, on page 3056• message-digest-key md5, on page 3057• message-digest-key md5, on page 3058• metric-style transition, on page 3059• metric-type, on page 3060• metric direct 0, on page 3061• metric maximum-hops, on page 3062• metric rib-scale, on page 3063• metric version 64bit, on page 3064• metric weights, on page 3065• mkdir, on page 3066• mode, on page 3067• mode, on page 3068• mode, on page 3069• mode tap-aggregation, on page 3070• module transceiver-frequency, on page 3071• monitor erspan granularity, on page 3072• monitor erspan origin ip-address, on page 3073• monitor erspan switch-id, on page 3074• monitor session, on page 3075• monitor session shut, on page 3076• monitor session type acl-capture, on page 3077• monitor session type erspan-destination, on page 3078• monitor session type erspan-source, on page 3079• monitor session warp, on page 3080• monitor session warp, on page 3081• mount, on page 3082• mount slot0, on page 3083
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2906
M Commands
Page 3051
• move, on page 3084• mst designated priority, on page 3085• mst root priority, on page 3086• mtrace, on page 3087• mtu, on page 3088• mtu1, on page 3089• mtu, on page 3090• mtu, on page 3091• mtu, on page 3092• mtu, on page 3093• mtu, on page 3094• mtu, on page 3095• multi-topology, on page 3096• multicast, on page 3097• multisite border-gateway interface, on page 3098• multisite ingress-replication, on page 3099• mvr-config, on page 3100• mvr-group, on page 3101• mvr-group, on page 3102• mvr-group, on page 3103• mvr-group, on page 3104• mvr-group, on page 3105• mvr-group, on page 3106• mvr-group, on page 3107• mvr-group, on page 3108• mvr-suppress-query vlan, on page 3109• mvr-type receiver, on page 3110• mvr-type source, on page 3111• mvr-vlan, on page 3112• mvr-vlan, on page 3113
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2907
M Commands
Page 3052
m2rib debug ftagm2rib debug ftag { add | del | mod } <ftag-id> <topo-id> { [ UCAST ] [ MCAST ] [ ACTIVE ] [ INACTIVE] } + [ <proto> ] [ vampire-tap ]
Syntax Description
Configure m2ribm2rib
Configure m2rib debugdebug
Configure M2RIB's ftag dbftag
Add an ftagadd
Modify an ftag flagsmod
Delete an ftagdel
ftag idftag-id
topo idtopo-id
(Optional) Protocol owner idproto
(Optional) Broadcast ftagUCAST
(Optional) Multicast ftagMCAST
(Optional) Active ftagACTIVE
(Optional) Inactive ftagINACTIVE
(Optional) Send a copy of all M2RIB generated messages to CLIvampire-tap
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2908
M Commandsm2rib debug ftag
Page 3053
m2rib debug gr-route add nhm2rib debug gr-route { add | del } <vlan> { { <v4-source> <v4-group> } | { <v6-source> <v6-group> } } {nh-if <if-name> | nh-sw <switch-id> } { [WC_SRC ] [WC_GRP ] [ NH_EXCLUDE ] [ FLOOD_TO_VLAN] [ LOCAL ] [ REMOTE ] [ IGNORE_STAR ] } + [ proto <proto> ] [ route-type <route-type> ] [ vampire-tap]
Syntax Description
Configure m2ribm2rib
Configure m2rib debugdebug
Perform group route operations on m2ribgr-route
Add a route next-hopadd
Delete a route next-hopdel
(Optional) Protocol owning this next-hopproto
(Optional) Route type of this next-hoproute-type
next-hop interfacenh-if
next-hop switchnh-sw
vlan keyvlan
IPv4 Multicast traffic sourcev4-source
IPv4 Multicast Group addressv4-group
Specify the next hop interfaceif-name
Specify the next hop switch idswitch-id
(Optional) Source is wildcardedWC_SRC
(Optional) Group is wildcardedWC_GRP
(Optional) Next-hop excluded from ltl+1NH_EXCLUDE
(Optional) Broadcast (flood-to-vlan) special groupFLOOD_TO_VLAN
(Optional) Local members existLOCAL
(Optional) Remote members existREMOTE
(Optional) Do not combine with router-port oif listIGNORE_STAR
(Optional) Protocol owner idproto
(Optional) Route typeroute-type
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2909
M Commandsm2rib debug gr-route add nh
Page 3054
(Optional) Send a copy of all M2RIB generated messages to CLIvampire-tap
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2910
M Commandsm2rib debug gr-route add nh
Page 3055
m2rib debug log-size event-historym2rib debug log-size event-history { <size> | small | medium | large }
Syntax Description
Configure m2ribm2rib
Configure m2rib debugdebug
Set log sizeslog-size
Set event-history sizeevent-history
Buffer size in KBsize
Set to default small log sizesmall
Set to default medium log sizemedium
Set to default large log sizelarge
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2911
M Commandsm2rib debug log-size event-history
Page 3056
m2rib debug log-size transactionsm2rib debug log-size transactions { { received | u2rib | mfdm | pixm | eltm } [ error-log ] | announced } {<size> | small | medium | large } <size_bytes>
Syntax Description
Configure m2ribm2rib
Configure m2rib debugdebug
Set log sizeslog-size
Set transaction log sizestransactions
Set received transaction log sizereceived
Set announced transaction log sizeannounced
Set U2RIB transaction log sizeu2rib
Set MFDM transaction log sizemfdm
Set PIXM transaction log sizepixm
Set ELTM transaction log sizeeltm
(Optional) errors only logerror-log
Size in number of transactionssize
Set number of transactions default small log size (0 disables limits)small
Set numbser of transactions default medium log sizemedium
Set number of transactions default large log sizelarge
Max log size in number of bytessize_bytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2912
M Commandsm2rib debug log-size transactions
Page 3057
m2rib debug omf enablem2rib debug omf { enable | disable } <from-vlan> <to-vlan> [ vampire-tap ]
Syntax Description
Configure m2ribm2rib
Configure m2rib debugdebug
Enable or disable Optimized Multicast Flood (OMF)omf
Enable OMFenable
Disable OMFdisable
from vlanfrom-vlan
to vlanto-vlan
(Optional) Send a copy of all M2RIB generated messages to CLIvampire-tap
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2913
M Commandsm2rib debug omf enable
Page 3058
m2rib debug pkt-recv enablem2rib debug pkt-recv { enable | disable } <from-vlan> <to-vlan> <proto> [ vampire-tap ]
Syntax Description
Configure m2ribm2rib
Configure m2rib debugdebug
Enable or disable protocol packet receptionpkt-recv
Enable packet receiveenable
Disable packet receivedisable
from vlanfrom-vlan
to vlanto-vlan
Protocol idproto
(Optional) Send a copy of all M2RIB generated messages to CLIvampire-tap
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2914
M Commandsm2rib debug pkt-recv enable
Page 3059
m2rib debug swroute nhm2rib debug swroute { add | mod | del } <ftag> <switch-id> nh <if-name> [ proto <proto> ] [ route-type<route-type> ] [ vampire-tap ]
Syntax Description
Configure m2ribm2rib
Configure m2rib debugdebug
Perform route operations on m2ribswroute
Add a route next-hopadd
Modify a route's next-hopmod
Delete a route next-hopdel
next-hopnh
(Optional) Protocol owning this next-hopproto
(Optional) Route type of this next-hoproute-type
ftag keyftag
switch idswitch-id
Specify the next hop interfaceif-name
(Optional) Protocol owner idproto
(Optional) Route typeroute-type
(Optional) Send a copy of all M2RIB generated messages to CLIvampire-tap
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2915
M Commandsm2rib debug swroute nh
Page 3060
m2rib debug topom2rib debug topo { create | del | add-vlans | del-vlans } <topo-id> <from-vlan> <to-vlan> [ <proto> ] [vampire-tap ]
Syntax Description
Configure m2ribm2rib
Configure m2rib debugdebug
Configure M2RIB's topo dbtopo
Create a topo in m2ribcreate
Delete a topo in m2ribdel
Add vlans to an existing topoadd-vlans
Delete vlans from an existing topodel-vlans
topo idtopo-id
from vlanfrom-vlan
to vlanto-vlan
(Optional) Protocol owner idproto
(Optional) Send a copy of all M2RIB generated messages to CLIvampire-tap
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2916
M Commandsm2rib debug topo
Page 3061
m2rib debug topo loop-flush-timeoutm2rib debug topo [ <topo-id> ] loop-flush-timeout <timeout>
Syntax Description
Configure m2ribm2rib
Configure m2rib debugdebug
configure M2RIB's topology dbtopo
(Optional) topo idtopo-id
configure the loop flush timer valueloop-flush-timeout
Loop flush timeout value in mstimeout
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2917
M Commandsm2rib debug topo loop-flush-timeout
Page 3062
mac-addr{ mac-addr <dstmac> <smac> [ dot1q <dot1q-id> ] }
Syntax Description
Macmac-addr
Destination mac addressdstmac
Source mac addresssmac
(Optional) Encapsulation dot1q/bddot1q
(Optional) Encapsulation dot1q/bd on which the mac is learntdot1q-id
Command Mode
• /exec/configure/configngoamccpayload
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2918
M Commandsmac-addr
Page 3063
mac-addressmac-address <mac_address_val> | no mac-address [ <mac_address_val> ]
Syntax Description
Negate a command or set its defaultsno
Configure interface mac address (1)mac-address
Static Router MAC address (1)mac_address_val
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-ether-sub /exec/configure/if-eth-non-member/exec/configure/if-remote-ethernet-sub /exec/configure/if-port-channel /exec/configure/if-port-channel-sub/exec/configure/if-ether-sub-p2p /exec/configure/if-ethernet-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2919
M Commandsmac-address
Page 3064
mac-addressmac-address <macaddress> | no mac-address [ <macaddress> ]
Syntax Description
Negate a command or set its defaultsno
Virtual MAC addressmac-address
MAC address(FORMAT:xxxx.xxxx.xxxx)macaddress
Command Mode
• /exec/configure/if-eth-any/hsrp_ipv4 /exec/configure/if-eth-any/hsrp_ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2920
M Commandsmac-address
Page 3065
mac-addressmac-address <mac-addr> | no mac-address
Syntax Description
Negate a command or set its defaultsno
Manually set interface MAC addressmac-address
MAC addressmac-addr
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2921
M Commandsmac-address
Page 3066
mac-address bpdu source version 2[no] mac-address bpdu source version 2
Syntax Description
(Optional) Negate a command or set its defaultsno
change vpc mac addressmac-address
bpdubpdu
sourcesource
versionversion
use version 2 bpdu source mac-address2
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2922
M Commandsmac-address bpdu source version 2
Page 3067
mac-address destination{ mac-address { destination | source } <addr> } | { no mac-address { destination | source } }
Syntax Description
Negate a command or set its defaultsno
specify flow mac addressmac-address
specify flow source mac addresssource
specify flow destination mac addressdestination
mac addressaddr
Command Mode
• /exec/configure/configngoamprofileflow
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2923
M Commandsmac-address destination
Page 3068
mac-address ipv6-extractmac-address ipv6-extract | no mac-address ipv6-extract
Syntax Description
Negate a command or set its defaultsno
Configure interface mac address (3)mac-address
Extract mac-address (3) from the IPv6 address configured on theinterface
ipv6-extract
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-ether-sub /exec/configure/if-eth-non-member/exec/configure/if-remote-ethernet-sub /exec/configure/if-port-channel-sub /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2924
M Commandsmac-address ipv6-extract
Page 3069
mac-learn disablemac-learn disable | no mac-learn disable
Syntax Description
Negate a command or set its defaultsno
Mac Learning disable/enablemac-learn
Mac Learning disable to use switch as a HUB. Do a clear macaddress-table dynamic after disabling mac learning
disable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2925
M Commandsmac-learn disable
Page 3070
mac-learn disablemac-learn disable | no mac-learn disable
Syntax Description
Negate a command or set its defaultsno
Mac Learning disable/enable on vlanmac-learn
Mac Learning disable on vlandisable
Command Mode
• /exec/configure/vlan-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2926
M Commandsmac-learn disable
Page 3071
mac-list permit{ mac-list <name> [ seq <seq> ] { permit | deny } <mac-addr> [ <mac-mask> ] } | { no mac-list <name> [seq <seq> ] [ { permit | deny } <mac-addr> [ <mac-mask> ] ] }
Syntax Description
Negate a command or set its defaultsno
Build a mac listmac-list
Name of prefix listname
(Optional) Sequence number of an entryseq
(Optional) Sequence numberseq
Specify routes to forwardpermit
Specify routes to rejectdeny
MAC addressmac-addr
(Optional) MAC Mask. Default Mask is ffff.ffff.ffffmac-mask
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2927
M Commandsmac-list permit
Page 3072
mac access-list[no] mac access-list <name> [ client <clienttype> <clientID> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
MAC configuration commandsmac
Configure access listaccess-list
List namename
(Optional) set client typeclient
(Optional) CLI/ONEPclienttype
(Optional) client appIDclientID
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2928
M Commandsmac access-list
Page 3073
mac address-table aging-timemac address-table aging-time { 0 | <seconds> } [ { vlan <vlan-id> } ] [ __readonly__ <info_str> ] | no macaddress-table aging-time [ [ 0 | <seconds> ] ]
Syntax Description
Negate a command or set its defaultsno
MAC configuration commandsmac
MAC Address Tableaddress-table
Aging timeaging-time
0 disables aging0
Aging time in seconds.seconds
(Optional) VLANvlan
(Optional) VLAN IDvlan-id
(Optional)__readonly__
(Optional) Informationinfo_str
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2929
M Commandsmac address-table aging-time
Page 3074
mac address-table guard-vpc-peergw-mac[no] mac address-table guard-vpc-peergw-mac
Syntax Description
(Optional) Negate a command or set its defaultsno
MAC configuration commandsmac
MAC Address Tableaddress-table
Prevent vPC Peer gateway MAC Spoofingguard-vpc-peergw-mac
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2930
M Commandsmac address-table guard-vpc-peergw-mac
Page 3075
mac address-table limit systemmac address-table limit { system | vlan <id> } [ <limitcount> ] [ actiondrop ] [ __readonly__ <info_str> ] |no mac address-table limit { system | vlan <id> } [ <limitcount> ] [ actiondrop ]
Syntax Description
Negate a command or set its defaultsno
MAC configuration commandsmac
MAC Address Tableaddress-table
Restrict number of Mac addresses learntlimit
System-widesystem
VLANvlan
List of VLAN idsid
(Optional) Mac address limit countlimitcount
(Optional) Drop packets instead of floodingactiondrop
(Optional)__readonly__
(Optional) Informationinfo_str
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2931
M Commandsmac address-table limit system
Page 3076
mac address-table loop-detect port-downmac address-table loop-detect port-down | no mac address-table loop-detect port-down
Syntax Description
Negate a command or set its defaultsno
MAC configuration commandsmac
MAC Address Tableaddress-table
Action for Mac loop detectionloop-detect
Take port-down action for mac loop detectionport-down
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2932
M Commandsmac address-table loop-detect port-down
Page 3077
mac address-table multicast vlan interface[no] mac address-table multicast <mac-address> { vlan <vlan> | bridge-domain <bdid> } interface [ vsi ]<interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
MAC configuration commandsmac
MAC Address Tableaddress-table
mcast mac OIF Static Entrymulticast
mcast MAC Address, not in Unicast IP Rangemac-address
VLANvlan
VLANvlan
BDbridge-domain
BDbdid
Interfaceinterface
(Optional) Specify if this interface is a VSIvsi
Interface nameinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2933
M Commandsmac address-table multicast vlan interface
Page 3078
mac address-table notification mac-movemac address-table notification mac-move | no mac address-table notification mac-move
Syntax Description
Negate a commandno
MAC configuration commandsmac
MAC Address Tableaddress-table
Notify of mac-movenotification
MAC move notification on syslogmac-move
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2934
M Commandsmac address-table notification mac-move
Page 3079
mac address-table notification thresholdmac address-table notification threshold [ limit <percentage> interval <seconds> ] | no mac address-tablenotification threshold
Syntax Description
Negate a commandno
MAC configuration commandsmac
MAC Address Tableaddress-table
Notify of mac-movenotification
MAC Address Table threshold notificationthreshold
(Optional) Specify the percentage limit beyond which notifications areenabled
limit
(Optional) Percentage of MAC Table Consumptionpercentage
(Optional) Minimum time in seconds between two notificationsinterval
(Optional) Interval time in secondsseconds
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2935
M Commandsmac address-table notification threshold
Page 3080
mac address-table static vlan interfacemac address-table static <mac-address> vlan <vlan-id> { interface <interface-name> | drop } [ auto-learn ] [__readonly__ <info_str> ] | no mac address-table static <mac-address> vlan <vlan-id>
Syntax Description
Negate a command or set its defaultsno
MAC configuration commandsmac
MAC Address Tableaddress-table
Static Entrystatic
MAC Addressmac-address
VLANvlan
VLAN IDvlan-id
Interfaceinterface
Interface nameinterface-name
Drop all trafficdrop
(Optional) Allow moving this MAC addressauto-learn
(Optional)__readonly__
(Optional) Informationinfo_str
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2936
M Commandsmac address-table static vlan interface
Page 3081
mac address-table static vnimac address-table static <mac-address> vni <vni-id>
Syntax Description
MAC configuration commandsmac
MAC Address Tableaddress-table
Static Entrystatic
MAC Addressmac-address
Virtual Network Identifiervni
VNI IDvni-id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2937
M Commandsmac address-table static vni
Page 3082
mac address[no] mac address { <macaddr> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure vMAC address options for Pathwaymac
Pathway will use a specified vMAC addressaddress
48-bit MAC address in HEXmacaddr
Command Mode
• /exec/configure/if-eth-any/vrrs
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2938
M Commandsmac address
Page 3083
mac address inheritmac address inherit
Syntax Description
Configure vMAC address options for Pathwaymac
Pathway will use a specified vMAC addressaddress
Pathway will inherit vMACinherit
Command Mode
• /exec/configure/if-eth-any/vrrs
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2939
M Commandsmac address inherit
Page 3084
mac advert interval[no] mac advert interval | mac advert interval <macint>
Syntax Description
Negate a command or set its defaultsno
Configure vMAC address options for Pathwaymac
Specify vMAC unsolicited advertisementsadvert
Specify interval between vMAC unsolicited advertisementsinterval
Advertisement Interval in secondsmacint
Command Mode
• /exec/configure/if-eth-any/vrrs
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2940
M Commandsmac advert interval
Page 3085
mac packet-classify[no] mac packet-classify
Syntax Description
(Optional) Negate a command or set its defaultsno
MACmac
Force mac classification of packetspacket-classify
Command Mode
• /exec/configure/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2941
M Commandsmac packet-classify
Page 3086
mac packet-classify[no] mac packet-classify
Syntax Description
(Optional) Negate a command or set its defaultsno
MAC configuration commandsmac
Force mac classification of packetspacket-classify
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-remote-ethernet-switch/exec/configure/if-eth-port-channel-switch /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2942
M Commandsmac packet-classify
Page 3087
mac port access-group[no] mac port access-group <name>
Syntax Description
(Optional) Negate a command or set its defaultsno
MAC configuration commandsmac
Port policyport
Specify access control for packetsaccess-group
List namename
Command Mode
• /exec/configure/if-set-acl-l2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2943
M Commandsmac port access-group
Page 3088
managed-config-flag[no] managed-config-flag <state>
Syntax Description
(Optional) Negate a command or set its defaultsno
state
Command Mode
• /exec/configure/config-ra-guard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2944
M Commandsmanaged-config-flag
Page 3089
management[no] management
Syntax Description
(Optional) Negate a command or set its defaultsno
Allow in-band management access to VLAN Interface IP addressmanagement
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2945
M Commandsmanagement
Page 3090
map-notify-group{ [ no ] map-notify-group { <addr> | <addr6> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Group address to send and receive site specific Map-Notify messagesmap-notify-group
IPv4 group addressaddr
Command Mode
• /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2946
M Commandsmap-notify-group
Page 3091
map-server key{ { [ no ] map-server { <ms> | <ms6> } [ key-type { sha1 | sha2 } ] key <key> } | { [ no ] map-server { <ms>| <ms6> } proxy-reply } }
Syntax Description
(Optional) Negate a command or set its defaultsno
To interact with Map-Servermap-server
Address of IPv4 map-serverms
(Optional) Authentication key type, either sha1 or sha2key-type
(Optional) Use sha1 authenication in Map-Register messagessha1
(Optional) Use sha2 authenication in Map-Register messagessha2
Authentication key used with Map-Serverkey
SHA-1 password keykey
Request Map-Server to send Map-Replies on behalf of dynamic-EIDproxy-reply
Command Mode
• /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2947
M Commandsmap-server key
Page 3092
marker-packet-n3500[no] marker-packet-n3500 [ <interval> | seconds <interval1> | milliseconds <interval2> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/Disable send marker packetmarker-packet-n3500
(Optional) range between <1-4> secondinterval
(Optional) Configure interval in secsseconds
(Optional) range between <1-4> secondinterval1
(Optional) Interval in milli second.milliseconds
(Optional) range between <100-900> msecs, increments in mutliples of100
interval2
Command Mode
• /exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2948
M Commandsmarker-packet-n3500
Page 3093
marker-packet[no] marker-packet [ <interval> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/Disable send marker packetmarker-packet
(Optional)interval
Command Mode
• /exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2949
M Commandsmarker-packet
Page 3094
master ipv4[no] master ipv4 <ip>
Syntax Description
(Optional) Negate a command or set its defaultsno
mastermaster
ipv4ipv4
IPv4 address (A.B.C.D) of slaveip
Command Mode
• /exec/configure/ptp-ucast-slave
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2950
M Commandsmaster ipv4
Page 3095
match-address[no] match-address
Syntax Description
(Optional) Negate a command or set its defaultsno
Match addresses in advertisement packetsmatch-address
Command Mode
• /exec/configure/if-eth-any/vrrpv3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2951
M Commandsmatch-address
Page 3096
match[no] match { { access-group name <acl-name> } | [ not ] { dscp { <dscp-list> | { <dscp-enum> } + } | { {packet length <len-list> | ip rtp <port-list> } [ replace ] } | { cos <cos-list> } | { qos-group <qos-group-list>} | { precedence { <precedence-list> | { <prec-enum> } + } } | { protocol <protocol-enum> } | { mplsexperimental topmost <exp-list> } | { ip roce <port-list> } } }
Syntax Description
<dscp-enum>dscp-list
cos-list
<prec-enum>precedence-list
(Optional) Negate a command or set its defaultsno
(Optional) Replace current ip rtp / packet length configurationreplace
Classification criteriamatch
(Optional) Negate this match resultnot
Access groupaccess-group
Named Access Listname
Access List nameacl-name
DSCP in IP(v4) and IPv6 packetsdscp
dscp-enum
IEEE 802.1Q Class of Servicecos
Qos-groupqos-group
List of qos-group valuesqos-group-list
Precedence in IP(v4) and IPv6 packetsprecedence
prec-enum
Protocolprotocol
protocol-enum
Packetpacket
Length of IP datagramlength
List of IP packet lengthlen-list
IPip
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2952
M Commandsmatch
Page 3097
Real Time Protocolrtp
UDP port list that are using RTPport-list
Match on MPLS labelmpls
Match on MPLS Experimental labelexperimental
Match on topmost MPLS labeltopmost
IPip
Roce protocol. port to be used 3804roce
UDP port list that are using RoCEport-list
List of MPLS exp valuesexp-list
Command Mode
• /exec/configure/class-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2953
M Commandsmatch
Page 3098
match[no] match { [ not ] { { discard-class <discard-class-list> } | { class-map <cmap-name> } } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
(Optional) Negate this match resultnot
Discard classdiscard-class
List of discard-class valuesdiscard-class-list
Class mapclass-map
Match class-map namecmap-name
Command Mode
• /exec/configure/class-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2954
M Commandsmatch
Page 3099
match[no] match { { access-group name <acl-name> } | [ not ] { { cos <cos-value> } | any | { eth-src <mac_src><mac_src_wild> } | { eth-dest <mac_dest> <mac_dest_wild> } | { eth-type <eth-value> } | { vlan<vlan-number> } | { ip-tos <tos-value> <tos-mask> } | { ip-protocol <ip-protocol-value> } | { ip-src-addr<ip-s-addr> <ip-s-mask> } | { ip-dst-addr <ip-d-addr> <ip-d-mask> } | { tcp-src-port <tcp-src-port-addr> } |{ tcp-dst-port <tcp-dest-port-addr> } | { udp-src-port <udp-src-port-addr> } | { udp-dst-port<udp-dest-port-addr> } | { input-interface <ifnum> } | { ipv6-src-addr <ipv6-s-addr> <ipv6-s-mask> } | {ipv6-dst-addr <ipv6-d-addr> <ipv6-d-mask> } | { ipv6-protocol <ipv6-protocol-value> } | { ipv6-flowlabel<ipv6-flowlabel-value> } | { icmpv6-type <icmpv6-type-value> } | { icmpv6-code <icmpv6-code-value> } |{ ipv4-dscp <ipv4-dscp-list> } | { ipv6-dscp <ipv6-dscp-list> } | { dscp { <dscp-list> | <dscp-enum> } + } |{ precedence { <precedence-list> | <prec-enum> } + } | { discard-class <discard-class-list> } | { qos-group<qos-group-list> } | { class-map <cmap-name-plc> } | { protocol <protocol-enum> } | { packet length <len-list>} | { ip rtp <port-list> } | { mpls experimental topmost <exp-list> } } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
(Optional) Negate this match resultnot
Access groupaccess-group
Named Access Listname
Access List nameacl-name
IEEE 802.1Q class of servicecos
DSCP in IP(v4) and IPv6 packetsdscp
List of DSCP valuesdscp-list
dscp-enum
Precedence in IP(v4) and IPv6 packetsprecedence
List of precedence valuesprecedence-list
prec-enum
Discard classdiscard-class
List of discard-class valuesdiscard-class-list
Qos-groupqos-group
List of qos-group valuesqos-group-list
Class mapclass-map
Match class-map namecmap-name-plc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2955
M Commandsmatch
Page 3100
Protocolprotocol
protocol-enum
Packetpacket
Length of IP datagramlength
list of IP packet lengthlen-list
IPip
Real Time Protocolrtp
UDP port list that are using RTPport-list
Match on MPLS labelmpls
Match on MPLS Experimental labelexperimental
Match on topmost MPLS labeltopmost
List of MPLS exp valuesexp-list
Match on Any Filterany
Match on Layer 2 destination MAC addresseth-dest
Match on Layer 2 source MAC addresseth-src
Match on Ether typeeth-type
Match on 802.1Q vlanvlan
Match on IPv4 TOSip-tos
Match on IP protocolip-protocol
Match on IPv4 source addressip-src-addr
Match on IPv4 destination addressip-dst-addr
Match on IPv6 source addressipv6-src-addr
Match on IPv6 destination addressipv6-dst-addr
Match on TCP source porttcp-src-port
Match on TCP source porttcp-dst-port
Match on UDP source portudp-src-port
Match on UDP source portudp-dst-port
Match on physical input interfaceinput-interface
Match on IPv6 Protocol Valueipv6-protocol
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2956
M Commandsmatch
Page 3101
Match on IPv6 Flowlabelipv6-flowlabel
Match on ICMPv6 Message Typeicmpv6-type
Match on ICMPv6 Message Codeicmpv6-code
Match on DSCP for IPV4 Packetsipv4-dscp
Match on DSCP for IPV6 Packetsipv6-dscp
class of service Valuecos-value
Source MAC addressmac_src
Source MAC maskmac_src_wild
Destination MAC addressmac_dest
Destination MAC maskmac_dest_wild
Ethernet typeeth-value
Vlan numbervlan-number
IPv4 TOStos-value
IPV4 TOS Mask for DSCPtos-mask
IPV4 protocolip-protocol-value
IPV4 address in format a.b.c.dip-s-addr
IPV4 address in format a.b.c.dip-d-addr
IPV4 address Mask in format a.b.c.dip-s-mask
IPV4 address Mask in format a.b.c.dip-d-mask
Transport layer port numbertcp-src-port-addr
Transport layer port numbertcp-dest-port-addr
Transport layer port numberudp-src-port-addr
Transport layer port numberudp-dest-port-addr
Physical interface Name and Numberifnum
IPv6 Protocol Valueipv6-protocol-value
IPv6 Flowlabelipv6-flowlabel-value
ICMPv6 Message Typeicmpv6-type-value
ICMPv6 Message Codeicmpv6-code-value
List of IPV4 DSCP valuesipv4-dscp-list
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2957
M Commandsmatch
Page 3102
List of IPV6 DSCP valuesipv6-dscp-list
Command Mode
• /exec/configure/class-map/type/plc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2958
M Commandsmatch
Page 3103
match access-group name[no] match access-group name <acs-grp-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
Match with given access groupaccess-group
Name of the access groupname
Match parameter for class-mapacs-grp-name
Command Mode
• /exec/configure/cmap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2959
M Commandsmatch access-group name
Page 3104
match address[no] match <ip_ipv6_mac> address <name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Specify the match clausematch
IP/IPv6/MACip_ipv6_mac
Match an access listaddress
List namename
Command Mode
• /exec/configure/vacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2960
M Commandsmatch address
Page 3105
match as-number[no] match as-number [ { <asnum> | <asnum_range> } + ] { <asnum_trail> | <asnum_range_trail> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Match values from routing tablematch
Match BGP peer AS numberas-number
(Optional) <AA4>,asnum
(Optional) <AA4>-<AA4>,asnum_range
<AA4>,asnum_trail
<AA4>-<AA4>,asnum_range_trail
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2961
M Commandsmatch as-number
Page 3106
match as-number as-path-listmatch as-number as-path-list <aspl-name> + | no match as-number as-path-list { <aspl-name> | <aspl-name>} +
Syntax Description
Negate a command or set its defaultsno
Match values from routing tablematch
Match BGP peer AS numberas-number
AS-path access-listas-path-list
AS path access list nameaspl-name
AS path access list nameaspl-name
Known as-path access-list nameaspl-name
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2962
M Commandsmatch as-number as-path-list
Page 3107
match as-pathmatch as-path <aspl-name> + | no match as-path { <aspl-name> | <aspl-name> } +
Syntax Description
Negate a command or set its defaultsno
Match values from routing tablematch
Match BGP AS path listas-path
AS path access list nameaspl-name
AS path access list nameaspl-name
Known as-path access-list nameaspl-name
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2963
M Commandsmatch as-path
Page 3108
match class-map[no] match class-map <cmap-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
Class mapclass-map
class map namecmap-name
Command Mode
• /exec/configure/class-map/type/queuing
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2964
M Commandsmatch class-map
Page 3109
match community[no] match community <name> + [ exact-match ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Match values from routing tablematch
Match BGP community listcommunity
Community list namename
(Optional) Do exact matching of communitiesexact-match
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2965
M Commandsmatch community
Page 3110
match cos[no] match cos <cos-list>
Syntax Description
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
IEEE 802.1Q class of servicecos
List of class-of-service valuescos-list
Command Mode
• /exec/configure/class-map/type/uf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2966
M Commandsmatch cos
Page 3111
match cos[no] match cos <cos-list>
Syntax Description
cos-list
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
IEEE 802.1Q Class of Servicecos
Command Mode
• /exec/configure/class-map/type/queuing
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2967
M Commandsmatch cos
Page 3112
match datalink[no] match datalink { mac source-address | mac destination-address | ethertype | vlan }
Syntax Description
Specify a key fieldmatch
datalink (Layer 2) attributesdatalink
MAC Addressmac
Source MAC Addresssource-address
Destination MAC Addressdestination-address
Ethertypeethertype
VLAN IDvlan
Command Mode
• /exec/configure/nfm-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2968
M Commandsmatch datalink
Page 3113
match datalink[no] match datalink { mac source-address | mac destination-address | ethertype }
Syntax Description
Specify a key fieldmatch
datalink (Layer 2) attributesdatalink
MAC Addressmac
Source MAC Addresssource-address
Destination MAC Addressdestination-address
Ethertypeethertype
Command Mode
• /exec/configure/config-fte-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2969
M Commandsmatch datalink
Page 3114
match dscp[no] match dscp { <dscp-list> | <dscp-enum> } +
Syntax Description
<dscp-enum>dscp-list
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
DSCP in IP(v4) and IPv6 packetsdscp
dscp-enum
Command Mode
• /exec/configure/color-cmap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2970
M Commandsmatch dscp
Page 3115
match dscp[no] match dscp { <dscp-list> } +
Syntax Description
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
DSCP in IP(v4) packetsdscp
List of DSCP valuesdscp-list
Command Mode
• /exec/configure/class-map/type/queuing
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2971
M Commandsmatch dscp
Page 3116
match exception[no] match exception { { { ip | ipv6 } { option | { icmp { redirect | unreachable } } | municast } } | ttl-failure| glean | mtu-failure | nat-flow | sflow | { multicast { rpf-failure | sg-rpf-failure | dest-miss | ipv6-rpf-failure |ipv6-sg-rpf-failure | ipv6-dest-miss } } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
Match exception packetsexception
ipv4 match criteriaip
ipv6 match criteriaipv6
Match ip/ipv6 option exception packetsoption
Icmp redirect packetsicmp
Send redirected packets back to senderredirect
Send unreachable packets back to senderunreachable
IP unicast packets with multicast MACmunicast
Failed in ttlttl-failure
mtu-failuremtu-failure
Glean packetsglean
multicast packetsmulticast
multicast rpf check failurerpf-failure
multicast sg rpf check failuresg-rpf-failure
L3 multicast destination lookup failuredest-miss
IPv6 multicast rpf check failureipv6-rpf-failure
IPv6 multicast sg rpf check failureipv6-sg-rpf-failure
IPv6 L3 multicast destination lookup failureipv6-dest-miss
ipv4 software nat flow packetsnat-flow
sflow packetssflow
Command Mode
• /exec/configure/cmap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2972
M Commandsmatch exception
Page 3117
match extcommunity[no] match extcommunity <name> + [ exact-match ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Match values from routing tablematch
Match BGP community listextcommunity
Extended Community list namename
(Optional) Do exact matching of extended communitiesexact-match
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2973
M Commandsmatch extcommunity
Page 3118
match interface[no] match interface <name> +
Syntax Description
(Optional) Negate a command or set its defaultsno
Match values from routing tablematch
Match first hop interface of routeinterface
Interface namename
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2974
M Commandsmatch interface
Page 3119
match ip address[no] match ip address <name> +
Syntax Description
(Optional) Negate a command or set its defaultsno
Match values from routing tablematch
Configure IP featuresip
Match address of route or match packetaddress
IP access-list name (for use in route-maps for PBR only)name
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2975
M Commandsmatch ip address
Page 3120
match ip address prefix-listmatch ip address prefix-list <ipv4-pfl-name> + | no match ip address prefix-list { <ipv4-pfl-name> |<ipv4-pfl-name> } +
Syntax Description
Negate a command or set its defaultsno
Match values from routing tablematch
Configure IP featuresip
Match address of route or match packetaddress
Match entries of prefix-listsprefix-list
Name of prefix-listipv4-pfl-name
Name of prefix-listipv4-pfl-name
Known prefix-list nameipv4-pfl-name
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2976
M Commandsmatch ip address prefix-list
Page 3121
match ip multicast rp{ match ip multicast { { rp <iprp> [ rp-type <iprptype> ] } | { group <gprefix> } | { source <ipsrc> } } + } |{ match ip multicast { { rp <iprp> [ rp-type <iprptype> ] } | { group-range <gaddr_start> to <gaddr_end> }| { source <ipsrc> } } + } | { no match ip multicast }
Syntax Description
Negate a command or set its defaultsno
Match values from routing tablematch
Configure IP featuresip
Match multicast attributesmulticast
Rendezvous pointrp
IPv4 rendezvous prefixiprp
(Optional) Multicast rendezvous point typerp-type
(Optional) IPv4 rendezvous point typeiprptype
Multicast Group prefixgroup
IPv4 group prefixgprefix
Multicast Group address rangegroup-range
First Group addressgaddr_start
Rangeto
Last Group addressgaddr_end
Multicast source addresssource
IPv4 source prefixipsrc
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2977
M Commandsmatch ip multicast rp
Page 3122
match ip next-hop prefix-listmatch ip next-hop prefix-list <ipv4-pfl-name> + | no match ip next-hop prefix-list { <ipv4-pfl-name> |<ipv4-pfl-name> } +
Syntax Description
Negate a command or set its defaultsno
Match values from routing tablematch
Configure IP featuresip
Match next-hop address of routenext-hop
Match entries of prefix-listsprefix-list
Name of prefix-listipv4-pfl-name
Name of prefix-listipv4-pfl-name
Known prefix-list nameipv4-pfl-name
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2978
M Commandsmatch ip next-hop prefix-list
Page 3123
match ip protocol[no] match ip { protocol | tos }
Syntax Description
Specify a key fieldmatch
IP attributesip
Protocolprotocol
TOStos
Command Mode
• /exec/configure/nfm-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2979
M Commandsmatch ip protocol
Page 3124
match ip route-source prefix-listmatch ip route-source prefix-list <ipv4-pfl-name> + | no match ip route-source prefix-list { <ipv4-pfl-name>| <ipv4-pfl-name> } +
Syntax Description
Negate a command or set its defaultsno
Match values from routing tablematch
Configure IP featuresip
Match advertising source address of routeroute-source
Match entries of prefix-listsprefix-list
Name of prefix-listipv4-pfl-name
Name of prefix-listipv4-pfl-name
Known prefix-list nameipv4-pfl-name
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2980
M Commandsmatch ip route-source prefix-list
Page 3125
match ipv4 protocol[no] match ipv4 { protocol | tos }
Syntax Description
Specify a key fieldmatch
IPv4 attributesipv4
Protocolprotocol
TOStos
Command Mode
• /exec/configure/config-fte-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2981
M Commandsmatch ipv4 protocol
Page 3126
match ipv4 source address[no] match ipv4 { source | destination } address
Syntax Description
Specify a key fieldmatch
IPv4 attributesipv4
Source Addresssource
Destination Addressdestination
Addressaddress
Command Mode
• /exec/configure/config-fte-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2982
M Commandsmatch ipv4 source address
Page 3127
match ipv4 source address[no] match ipv4 { source | destination } address
Syntax Description
Specify a key fieldmatch
IPv4 attributesipv4
Source Addresssource
Destination Addressdestination
Addressaddress
Command Mode
• /exec/configure/nfm-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2983
M Commandsmatch ipv4 source address
Page 3128
match ipv4 transport destination[no] match ipv4 transport { destination-port | source-port }
Syntax Description
Specify a key fieldmatch
IPv4 attributesipv4
Transport layer fieldstransport
Transport destination portdestination-port
Transport source portsource-port
Command Mode
• /exec/configure/config-fte-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2984
M Commandsmatch ipv4 transport destination
Page 3129
match ipv6[no] match ipv6 { { { source | destination } address } | { flow-label | options } }
Syntax Description
Specify a key fieldmatch
IPv6 attributesipv6
Source Addresssource
Destination Addressdestination
Addressaddress
Flow labelflow-label
Optionsoptions
Command Mode
• /exec/configure/nfm-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2985
M Commandsmatch ipv6
Page 3130
match ipv6[no] match ipv6 { { { source | destination } address } | { flow-label } }
Syntax Description
Specify a key fieldmatch
IPv6 attributesipv6
Source Addresssource
Destination Addressdestination
Addressaddress
Flow labelflow-label
Command Mode
• /exec/configure/config-fte-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2986
M Commandsmatch ipv6
Page 3131
match ipv6 address[no] match ipv6 address <name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Match values from routing tablematch
Configure IPv6 featuresipv6
Match address of route or match packetaddress
IPv6 access-list name (for use in route-maps for PBR only)name
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2987
M Commandsmatch ipv6 address
Page 3132
match ipv6 address prefix-listmatch ipv6 address prefix-list <ipv6-pfl-name> + | no match ipv6 address prefix-list { <ipv6-pfl-name> |<ipv6-pfl-name> } +
Syntax Description
Negate a command or set its defaultsno
Match values from routing tablematch
Configure IPv6 featuresipv6
Match address of route or match packetaddress
Match entries of prefix-listsprefix-list
Name of prefix-listipv6-pfl-name
Name of prefix-listipv6-pfl-name
Known prefix-list nameipv6-pfl-name
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2988
M Commandsmatch ipv6 address prefix-list
Page 3133
match ipv6 multicast rp{ match ipv6 multicast { { rp <ipv6rp> [ rp-type <ipv6rptype> ] } | { group <gprefix> } | { source <ipv6src>} } + } | { match ipv6 multicast { { rp <ipv6rp> [ rp-type <ipv6rptype> ] } | { group-range <gaddr_start> to<gaddr_end> } | { source <ipv6src> } } + } | { no match ipv6 multicast }
Syntax Description
Negate a command or set its defaultsno
Match values from routing tablematch
Configure IPv6 featuresipv6
Match multicast attributesmulticast
Rendezvous pointrp
(Optional) Multicast rendezvous point typerp-type
(Optional) IPv6 rendezvous point typeipv6rptype
Multicast group addressgroup
Multicast Group address rangegroup-range
Rangeto
Multicast source addresssource
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2989
M Commandsmatch ipv6 multicast rp
Page 3134
match ipv6 next-hop prefix-listmatch ipv6 next-hop prefix-list <ipv6-pfl-name> + | no match ipv6 next-hop prefix-list { <ipv6-pfl-name> |<ipv6-pfl-name> } +
Syntax Description
Negate a command or set its defaultsno
Match values from routing tablematch
Configure IPv6 featuresipv6
Match next-hop address of routenext-hop
Match entries of prefix-listsprefix-list
Name of prefix-listipv6-pfl-name
Name of prefix-listipv6-pfl-name
Known prefix-list nameipv6-pfl-name
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2990
M Commandsmatch ipv6 next-hop prefix-list
Page 3135
match ipv6 protocol[no] match ipv6 { protocol | tos }
Syntax Description
Specify a key fieldmatch
IPv6 attributesipv6
Protocolprotocol
TOStos
Command Mode
• /exec/configure/config-fte-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2991
M Commandsmatch ipv6 protocol
Page 3136
match ipv6 route-source prefix-listmatch ipv6 route-source prefix-list <ipv6-pfl-name> + | no match ipv6 route-source prefix-list {<ipv6-pfl-name> | <ipv6-pfl-name> } +
Syntax Description
Negate a command or set its defaultsno
Match values from routing tablematch
Configure IPv6 featuresipv6
Match advertising source address of routeroute-source
Match entries of prefix-listsprefix-list
Name of prefix-listipv6-pfl-name
Name of prefix-listipv6-pfl-name
Known prefix-list nameipv6-pfl-name
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2992
M Commandsmatch ipv6 route-source prefix-list
Page 3137
match ipv6 transport destination[no] match ipv6 transport { destination-port | source-port }
Syntax Description
Specify a key fieldmatch
IPv6 attributesipv6
Transport layer fieldstransport
Transport destination portdestination-port
Transport source portsource-port
Command Mode
• /exec/configure/config-fte-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2993
M Commandsmatch ipv6 transport destination
Page 3138
match metric[no] match metric { <measure> [ <plus-minus> <deviation> ] } +
Syntax Description
(Optional) Negate a command or set its defaultsno
Match values from routing tablematch
Match metric of routemetric
(Optional) +-plus-minus
Metric valuemeasure
(Optional) Deviation valuedeviation
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2994
M Commandsmatch metric
Page 3139
match ospf-area[no] match ospf-area <area> +
Syntax Description
(Optional) Negate a command or set its defaultsno
Match values from routing tablematch
Match ospf areaospf-area
area idarea
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2995
M Commandsmatch ospf-area
Page 3140
match protocol[no] match protocol { fcoe | iscsi | tcp }
Syntax Description
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
Protocolprotocol
FCoEfcoe
ISCSIiscsi
TCPtcp
Command Mode
• /exec/configure/class-map/type/uf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2996
M Commandsmatch protocol
Page 3141
match protocol arp[no] match protocol { arp | mpls [ router-alert | exp <exp_value> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
Protocolprotocol
IP ARParp
Multi-protocol Label Switchingmpls
(Optional)Match packets with router-alert label set to 1 for OTVOverlayframes
router-alert
(Optional) Match packets on MPLS exp bitsexp
(Optional) Exp bits valueexp_value
Command Mode
• /exec/configure/cmap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2997
M Commandsmatch protocol arp
Page 3142
match qos-group[no] match qos-group { <qos-group-list> } +
Syntax Description
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
QoS Groupqos-group
List of qos-group valuesqos-group-list
Command Mode
• /exec/configure/class-map/type/queuing
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2998
M Commandsmatch qos-group
Page 3143
match qos-group2[no] match qos-group2 { <qos-group-list> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
QoS Groupqos-group2
qos-group-list
Command Mode
• /exec/configure/class-map/type/queuing
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)2999
M Commandsmatch qos-group2
Page 3144
match qos-group2[no] match qos-group2 <qos-group-list>
Syntax Description
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
QoS Groupqos-group2
qos-group-list
Command Mode
• /exec/configure/class-map/type/uf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3000
M Commandsmatch qos-group2
Page 3145
match qos-group[no] match qos-group <qos-group-list>
Syntax Description
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
QoS Groupqos-group
List of qos-group valuesqos-group-list
Command Mode
• /exec/configure/class-map/type/uf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3001
M Commandsmatch qos-group
Page 3146
match redirect[no] match redirect <opt_match_redirect>
Syntax Description
(Optional) Negate a command or set its defaultsno
Classification criteriamatch
Match redirected packetsredirect
Match criteria for redirected packetsopt_match_redirect
Command Mode
• /exec/configure/cmap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3002
M Commandsmatch redirect
Page 3147
match route-type[no] match route-type { external | internal | level-1 | level-2 | local | nssa-external | type-1 | type-2 | inter-area| intra-area } +
Syntax Description
(Optional) Negate a command or set its defaultsno
Match values from routing tablematch
Match route-type of routeroute-type
external route (BGP, EIGRP and OSPF type 1/2)external
internal route (including OSPF intra/inter area)internal
IS-IS level-1 routelevel-1
IS-IS level-2 routelevel-2
locally generated routelocal
nssa-external route (OSPF type 1/2)nssa-external
OSPF external type 1 routetype-1
OSPF external type 2 routetype-2
OSPF inter area routeinter-area
OSPF intra area routeintra-area
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3003
M Commandsmatch route-type
Page 3148
match source-protocol[no] match source-protocol <src_prot> +
Syntax Description
(Optional) Negate a command or set its defaultsno
Match values from routing tablematch
Match source protocolsource-protocol
Protocol instance namesrc_prot
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3004
M Commandsmatch source-protocol
Page 3149
match tag[no] match tag <tagid> +
Syntax Description
(Optional) Negate a command or set its defaultsno
Match values from routing tablematch
Match tag of routetag
Tag valuetagid
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3005
M Commandsmatch tag
Page 3150
match transport destination[no] match transport { destination-port | source-port }
Syntax Description
Specify a key fieldmatch
Transport layer fieldstransport
Transport destination portdestination-port
Transport source portsource-port
Command Mode
• /exec/configure/nfm-record
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3006
M Commandsmatch transport destination
Page 3151
max-backoffmax-backoff <maxbackoff-val> | no max-backoff
Syntax Description
Negate a command or set its defaultsno
OpenFlow controller maximum backoff timer (default is 8 seconds)max-backoff
max backoff timer value in secsmaxbackoff-val
Command Mode
• /exec/configure/openflow/switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3007
M Commandsmax-backoff
Page 3152
max-backoffmax-backoff <maxbackoff-val> | no max-backoff
Syntax Description
Negate a command or set its defaultsno
OpenFlow controller maximum backoff timer (default is 8 seconds)max-backoff
max backoff timer value in secsmaxbackoff-val
Command Mode
• /exec/configure/openflow/switch/sub-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3008
M Commandsmax-backoff
Page 3153
max-lsa[no] max-lsa <maximum-number> [ <threshold> ] [ warning-only | [ ignore-time <ignore-time-minutes> ] [ignore-count <ignore-count-number> ] [ reset-time <reset-time-minutes> ] ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Feature to limit the number of non-self-originated LSAsmax-lsa
Set maximum number of non self-generated LSAsmaximum-number
(Optional) Threshold value (%) at which to generate a warning messagethreshold
(Optional) Log a warning message when limit is exceededwarning-only
(Optional) Set time during which all adjacencies are suppressedignore-time
(Optional) ignore-time in minutesignore-time-minutes
(Optional) Set count on how many times adjacencies can be suppressedignore-count
(Optional) ignore-countignore-count-number
(Optional) Set number of minutes after which ignore-count is reset tozero
reset-time
(Optional) reset-time in minutesreset-time-minutes
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3009
M Commandsmax-lsa
Page 3154
max-lsa[no] max-lsa <maximum-number> [ <threshold> ] [ warning-only | [ ignore-time <ignore-time-minutes> ] [ignore-count <ignore-count-number> ] [ reset-time <reset-time-minutes> ] ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Feature to limit the number of non-self-originated LSAsmax-lsa
Set maximum number of non self-generated LSAsmaximum-number
(Optional) Threshold value (%) at which to generate a warning messagethreshold
(Optional) Log a warning message when limit is exceededwarning-only
(Optional) Set time during which all adjacencies are suppressedignore-time
(Optional) ignore-time in minutesignore-time-minutes
(Optional) Set count on how many times adjacencies can be suppressedignore-count
(Optional) ignore-countignore-count-number
(Optional) Set number of minutes after which ignore-count is reset tozero
reset-time
(Optional) reset-time in minutesreset-time-minutes
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3010
M Commandsmax-lsa
Page 3155
max-lsp-lifetimemax-lsp-lifetime <lifetime> | no max-lsp-lifetime [ <lifetime> ]
Syntax Description
Negate a command or set its defaultsno
Set maximum LSP lifetimemax-lsp-lifetime
Maximum LSP lifetime in secondslifetime
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3011
M Commandsmax-lsp-lifetime
Page 3156
max-lsp-lifetimemax-lsp-lifetime <lifetime> | no max-lsp-lifetime [ <lifetime> ]
Syntax Description
Negate a command or set its defaultsno
Set maximum LSP lifetimemax-lsp-lifetime
Maximum LSP lifetime in secondslifetime
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3012
M Commandsmax-lsp-lifetime
Page 3157
max-lsp-lifetimemax-lsp-lifetime <lifetime> | no max-lsp-lifetime [ <lifetime> ]
Syntax Description
Negate a command or set its defaultsno
Set maximum LSP lifetimemax-lsp-lifetime
Maximum LSP lifetime in secondslifetime
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3013
M Commandsmax-lsp-lifetime
Page 3158
max-metric router-lsa[no] max-metric router-lsa [ external-lsa [ <max-metric-extlsa> ] ] [ stub-prefix-lsa ] [ on-startup [ <timeout>] [ wait-for bgp <as> ] ] [ inter-area-prefix-lsa [ <max-metric-sumlsa> ] ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Maximize the cost metricmax-metric
Router LSArouter-lsa
(Optional) External LSAsexternal-lsa
(Optional) Max metric value for external LSAsmax-metric-extlsa
(Optional) Advertise Max metric for Stub links as wellstub-prefix-lsa
(Optional) Effective only at startupon-startup
(Optional) Wait period in seconds after startuptimeout
(Optional) Wait for an event to advertise normal metricwait-for
(Optional) BGP Convergencebgp
(Optional) ASN of BGP to wait foras
(Optional) Inter-area-prefix LSAsinter-area-prefix-lsa
(Optional) Max metric value for summary LSAsmax-metric-sumlsa
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3014
M Commandsmax-metric router-lsa
Page 3159
max-metric router-lsa[no] max-metric router-lsa [ external-lsa [ <max-metric-extlsa> ] ] [ include-stub ] [ on-startup [ <timeout> ][ wait-for bgp <as> ] ] [ summary-lsa [ <max-metric-sumlsa> ] ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Maximize the cost metricmax-metric
Router LSArouter-lsa
(Optional) External LSAsexternal-lsa
(Optional) Max metric value for external LSAsmax-metric-extlsa
(Optional) Advertise Max metric for Stub links as wellinclude-stub
(Optional) Effective only at startupon-startup
(Optional) Wait period in seconds after startuptimeout
(Optional) Wait for an event to advertise normal metricwait-for
(Optional) BGP Convergencebgp
(Optional) ASN of BGP to wait foras
(Optional) Summary LSAssummary-lsa
(Optional) Max metric value for summary LSAsmax-metric-sumlsa
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3015
M Commandsmax-metric router-lsa
Page 3160
max-ports[no] [ vmware ] max-ports
Syntax Description
Negate a command or set its defaultsno
(Optional) VMware configurationvmware
Max ports on which this profile can be inheritedmax-ports
Command Mode
• /exec/configure/port-profile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3016
M Commandsmax-ports
Page 3161
max-ports[ vmware ] max-ports <i0>
Syntax Description
(Optional) VMware configurationvmware
Max ports on which this profile can be inheritedmax-ports
Enter the max-number of portsi0
Command Mode
• /exec/configure/port-profile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3017
M Commandsmax-ports
Page 3162
maxas-limitmaxas-limit <as-limit> | no maxas-limit [ <as-limit> ]
Syntax Description
Negate a command or set its defaultsno
Allow AS-PATH attribute from EBGP neighbor imposing a limit onnumber of ASes
maxas-limit
Number of ASes in the AS-PATH attributeas-limit
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3018
M Commandsmaxas-limit
Page 3163
maximum-pathsmaximum-paths <max-paths> | no maximum-paths [ <max-paths> ]
Syntax Description
Negate a command or set its defaultsno
Maximum paths per destinationmaximum-paths
Maximum paths per destinationmax-paths
Command Mode
• /exec/configure/router-ospf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3019
M Commandsmaximum-paths
Page 3164
maximum-pathsmaximum-paths <max-paths> | no maximum-paths [ <max-paths> ]
Syntax Description
Negate a command or set its defaultsno
RIP set maximum paths per routemaximum-paths
Maximum paths per prefixmax-paths
Command Mode
• /exec/configure/router-rip/router-rip-af-common /exec/configure/router-rip/router-rip-vrf-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3020
M Commandsmaximum-paths
Page 3165
maximum-pathsmaximum-paths <max-paths> | no maximum-paths [ <max-paths> ]
Syntax Description
Negate a command or set its defaultsno
Set maximum paths per destinationmaximum-paths
Maximum paths per destinationmax-paths
Command Mode
• /exec/configure/router-isis/router-isis-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3021
M Commandsmaximum-paths
Page 3166
maximum-pathsmaximum-paths <max-paths> | no maximum-paths [ <max-paths> ]
Syntax Description
Negate a command or set its defaultsno
Set maximum paths per destinationmaximum-paths
Maximum paths per destinationmax-paths
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3022
M Commandsmaximum-paths
Page 3167
maximum-pathsmaximum-paths <max-paths> | no maximum-paths [ <max-paths> ]
Syntax Description
Negate a command or set its defaultsno
Maximum paths per destinationmaximum-paths
Maximum paths per destinationmax-paths
Command Mode
• /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3023
M Commandsmaximum-paths
Page 3168
maximum-paths{ { maximum-paths <num-paths> } | { no maximum-paths [ <num-paths> ] } }
Syntax Description
Negate a command or set its defaultsno
Forward packets over multiple pathsmaximum-paths
Number of pathsnum-paths
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3024
M Commandsmaximum-paths
Page 3169
maximum-pathsmaximum-paths [ ibgp ] <mpath-count> | no maximum-paths [ ibgp ] [ <mpath-count> ]
Syntax Description
Negate a command or set its defaultsno
Forward packets over multipath pathsmaximum-paths
(Optional) Configure multipath for IBGP pathsibgp
Number of parallel pathsmpath-count
Command Mode
• /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3025
M Commandsmaximum-paths
Page 3170
maximum-pathsmaximum-paths <max-paths> | no maximum-paths [ <max-paths> ]
Syntax Description
Negate a command or set its defaultsno
Set maximum paths per destinationmaximum-paths
Maximum paths per destinationmax-paths
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common /exec/configure/l2mp-isis/l2mp-isis-l2-topo
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3026
M Commandsmaximum-paths
Page 3171
maximum-paths eibgpmaximum-paths eibgp <mpath-count> | no maximum-paths eibgp [ <mpath-count> ]
Syntax Description
Negate a command or set its defaultsno
Forward packets over multipath pathsmaximum-paths
Configure multipath for both EBGP and IBGP pathseibgp
Number of parallel pathsmpath-count
Command Mode
• /exec/configure/router-bgp/router-bgp-vrf-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6/exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-vpnv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3027
M Commandsmaximum-paths eibgp
Page 3172
maximum-paths mixedmaximum-paths mixed <mpath-count> | no maximum-paths mixed [ <mpath-count> ]
Syntax Description
Negate a command or set its defaultsno
Forward packets over multipath pathsmaximum-paths
Configure multipath for local and remote pathsmixed
Number of parallel pathsmpath-count
Command Mode
• /exec/configure/router-bgp/router-bgp-vrf-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6/exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-vpnv6/exec/configure/router-bgp/router-bgp-af-l2vpn-evpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3028
M Commandsmaximum-paths mixed
Page 3173
maximum-peers{ maximum-peers <limit> | no maximum-peers [ <limit> ] }
Syntax Description
Negate a command or set its defaultsno
Maximum number of peers for this prefixmaximum-peers
Max. peers limitlimit
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-prefix
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3029
M Commandsmaximum-peers
Page 3174
maximum-prefix{ { maximum-prefix <value> [ <threshold> ] [ warning-only ] [ restart <time1> ] [ restart-count <count> ] [reset-time <time2> ] [ dampened ] } | { no maximum-prefix [ <value> [ <threshold> ] [ warning-only ] [ restart<time1> ] [ restart-count <count> ] [ reset-time <time2> ] [ dampened ] ] } }
Syntax Description
Negate a command or set its defaultsno
Maximum number of IP prefixes acceptable in aggregatemaximum-prefix
Number of IP prefixes for maximum-prefix limitvalue
(Optional) Threshold value (%) at which to generate a warning messagethreshold
(Optional) Only give warning message when limit is exceededwarning-only
(Optional) Duration for which a prefix source is ignoredrestart
(Optional) Restart interval in minutestime1
(Optional) Number of times sessions are auto-restartedrestart-count
(Optional) Number of timescount
(Optional) Duration after which restart history is clearedreset-time
(Optional) Reset time in minutestime2
(Optional) Exponentially increase restart time intervaldampened
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3030
M Commandsmaximum-prefix
Page 3175
maximum-prefixmaximum-prefix <limit> [ <percent> ] [ restart <restart-time> | warning-only ] | { no | default } maximum-prefix[ <limit> [ <percent> ] [ restart <restart-time> | warning-only ] ]
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Maximum number of prefixes from this neighbormaximum-prefix
Max. prefix limitlimit
(Optional) Threshold percentage at which to generate a warningpercent
(Optional) Restart bgp connection after limit is exceededrestart
(Optional) Restart interval in minutesrestart-time
(Optional) Only give a warning message when limit is exceededwarning-only
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-link-state/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3031
M Commandsmaximum-prefix
Page 3176
maximum-prefixmaximum-prefix <limit> [ <percent> ] [ restart <restart-time> | warning-only ] | { no | default } maximum-prefix[ <limit> [ <percent> ] [ restart <restart-time> | warning-only ] ]
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Maximum number of prefixes from this neighbormaximum-prefix
Max. prefix limitlimit
(Optional) Threshold percentage at which to generate a warningpercent
(Optional) Restart bgp connection after limit is exceededrestart
(Optional) Restart interval in minutesrestart-time
(Optional) Only give a warning message when limit is exceededwarning-only
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3032
M Commandsmaximum-prefix
Page 3177
maximum routes[no] maximum routes <limit> [ { <warnlevel> [ reinstall <threshold> ] } | warning-only ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Set a limitmaximum
Maximum number of routes allowed in this routing tableroutes
Maximum number of routes allowedlimit
(Optional) Threshold value (%) at which to generate a warning msgwarnlevel
(Optional) Reinstall previous rejected route due to over maximum routelimit
reinstall
(Optional) Threshold value (%) at which to reinstall routes back to VRFthreshold
(Optional) Only give a warning message if limit is exceededwarning-only
Command Mode
• /exec/configure/vrf-af-ipv4 /exec/configure/vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3033
M Commandsmaximum routes
Page 3178
mdix auto{ mdix auto | no mdix [ auto ] }
Syntax Description
Negate a command or set its defaultsno
Enable auto mdix modemdix
Enable auto mdix modeauto
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3034
M Commandsmdix auto
Page 3179
mdt asm-use-shared-tree[no] mdt asm-use-shared-tree
Syntax Description
(Optional) Negate a command or set its defaultsno
Backbone Multicast Distribution Treemdt
Use (*,G) only state, no remote source state is createdasm-use-shared-tree
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3035
M Commandsmdt asm-use-shared-tree
Page 3180
mdt data[no] mdt data <prefix> [ threshold <value> | immediate-switch ] [ route-map <policy-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Backbone Multicast Distribution Treemdt
Configure settings for Data MDTdata
List of group range prefixesprefix
(Optional) Data MDT switching thresholdthreshold
(Optional) Move to data mdt immediately if remote receiver existsimmediate-switch
(Optional) Threshold in kilobits per secvalue
(Optional) Specify policy for creating Data MDTsroute-map
(Optional) A route-map namepolicy-name
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3036
M Commandsmdt data
Page 3181
mdt data bidir-enable[no] mdt data bidir-enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Backbone Multicast Distribution Treemdt
Configure settings for Data MDTdata
Allow creation of data mdts for bidir customersbidir-enable
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3037
M Commandsmdt data bidir-enable
Page 3182
mdt defaultmdt default <mdt-default> | no mdt default [ <mdt-default> ]
Syntax Description
Negate a command or set its defaultsno
Backbone Multicast Distribution Treemdt
The default groupdefault
IP multicast group addressmdt-default
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3038
M Commandsmdt default
Page 3183
mdt enforce-bgp-mdt-safi[no] mdt enforce-bgp-mdt-safi
Syntax Description
(Optional) Negate a command or set its defaultsno
Backbone Multicast Distribution Treemdt
Depend on BGP MDT SAFI for auto-discoveryenforce-bgp-mdt-safi
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3039
M Commandsmdt enforce-bgp-mdt-safi
Page 3184
mdt mtu[no] mdt mtu <mtu-value>
Syntax Description
(Optional) Negate a command or set its defaultsno
Backbone Multicast Distribution Treemdt
The MTUmtu
MTU valuemtu-value
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3040
M Commandsmdt mtu
Page 3185
mdt pim hello-interval[no] mdt pim hello-interval <interval>
Syntax Description
(Optional) Negate a command or set its defaultsno
Backbone Multicast Distribution Treemdt
PIM protocol related parameterspim
Hello interval used between peershello-interval
Interval in millisecondsinterval
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3041
M Commandsmdt pim hello-interval
Page 3186
mdt pim jp-interval[no] mdt pim jp-interval <interval>
Syntax Description
(Optional) Negate a command or set its defaultsno
Backbone Multicast Distribution Treemdt
PIM protocol related parameterspim
Join-Prune interval used between peersjp-interval
Interval in secondsinterval
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3042
M Commandsmdt pim jp-interval
Page 3187
mdt source[no] mdt source <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Backbone Multicast Distribution Treemdt
Source interface to be used in the backbone networksource
Use IP address of this interfaceinterface
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3043
M Commandsmdt source
Page 3188
media-type automedia-type auto
Syntax Description
Select the media-type linkmedia-type
Select mgmt port as autoauto
Command Mode
• /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3044
M Commandsmedia-type auto
Page 3189
media-type rj45media-type rj45
Syntax Description
Select the media-type linkmedia-type
Select mgmt port rj45rj45
Command Mode
• /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3045
M Commandsmedia-type rj45
Page 3190
media-type sfpmedia-type sfp
Syntax Description
Select the media-type linkmedia-type
Select mgmt port sfpsfp
Command Mode
• /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3046
M Commandsmedia-type sfp
Page 3191
mediamedia <vlanshowinfo-media-type> | no media
Syntax Description
Negate a command or set its defaultsno
Media type of the VLANmedia
Select media typevlanshowinfo-media-type
Command Mode
• /exec/configure/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3047
M Commandsmedia
Page 3192
mediummedium <medium-type> | no medium <medium-type>
Syntax Description
Negate a command or set its defaultsno
Configure Interface medium modemedium
medium-type
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3048
M Commandsmedium
Page 3193
medium broadcast{ medium broadcast | no medium broadcast }
Syntax Description
Negate a command or set its defaultsno
Configure Interface medium modemedium
Broadcast mediumbroadcast
Command Mode
• /exec/configure/if-ethernet-p2p-switch /exec/configure/if-ethernet-p2p /exec/configure/if-ethernet-all/exec/configure/if-eth-l3-non-member /exec/configure/if-port-channel/exec/configure/if-remote-ethernet-sub /exec/configure/if-eth-port-channel-p2p/exec/configure/if-ethernet-p2p-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3049
M Commandsmedium broadcast
Page 3194
medium broadcast{ medium broadcast | no medium broadcast }
Syntax Description
Negate a command or set its defaultsno
Configure Interface medium modemedium
Broadcast mediumbroadcast
Command Mode
• /exec/configure/ppm-ethernet-switch /exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p/exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3050
M Commandsmedium broadcast
Page 3195
medium p2p{ medium p2p | no medium p2p }
Syntax Description
Negate a command or set its defaultsno
Configure Interface medium modemedium
Point-to-Point mediump2p
Command Mode
• /exec/configure/if-ethernet-p2p-switch /exec/configure/if-ethernet-p2p /exec/configure/if-ethernet-all/exec/configure/if-eth-l3-non-member /exec/configure/if-port-channel/exec/configure/if-remote-ethernet-sub /exec/configure/if-eth-port-channel-p2p/exec/configure/if-ethernet-p2p-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3051
M Commandsmedium p2p
Page 3196
medium p2p{ medium p2p | no medium p2p }
Syntax Description
Negate a command or set its defaultsno
Configure Interface medium modemedium
Point-to-Point mediump2p
Command Mode
• /exec/configure/ppm-ethernet-switch /exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p/exec/configure/if-port-channel-sub /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3052
M Commandsmedium p2p
Page 3197
member vlan{ member vlan <vlan-range> } | { no member vlan [ <vlan-range> ] }
Syntax Description
Negate a command or set its defaultsno
Set fabricpath topology VLAN membershipmember
Configure VLANs for Fabricpath Topologyvlan
VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19vlan-range
Command Mode
• /exec/configure/fp-topology
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3053
M Commandsmember vlan
Page 3198
member vni{ member vni <vni-range> } | { no member vni [ <vni-range> ] }
Syntax Description
Negate a command or set its defaultsno
Set fabricpath topology VNI membershipmember
Configure VNIs for L2MP Topologyvni
vni range, Example: 4096, 4099-5013, 5019vni-range
Command Mode
• /exec/configure/fp-topology
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3054
M Commandsmember vni
Page 3199
member vni[no] member vni <vni-range>
Syntax Description
(Optional) Negate a command or set its defaultsno
NVE VN-Segment Membershipmember
Virtual Network Identifiervni
vni range, Example: 5000 or 5001-5008vni-range
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3055
M Commandsmember vni
Page 3200
member vni associate-vrf[no] member vni <vni-range> associate-vrf
Syntax Description
(Optional) Negate a command or set its defaultsno
NVE VN-Segment Membershipmember
Virtual Network Identifiervni
vni range, Example: 5000 or 5001-5008vni-range
Associate vni with a vrfassociate-vrf
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3056
M Commandsmember vni associate-vrf
Page 3201
message-digest-key md5{ { message-digest-key <keyid> md5 <key> } | { no message-digest-key [ <keyid> md5 <key> ] } }
Syntax Description
Negate a command or set its defaultsno
Message digest authentication password (key)message-digest-key
Key IDkeyid
Use MD5 algorithmmd5
The OSPF password (key)key
Command Mode
• /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3057
M Commandsmessage-digest-key md5
Page 3202
message-digest-key md5{ { message-digest-key <keyid> md5 <key> } | { no message-digest-key [ <keyid> md5 <key> ] } }
Syntax Description
Negate a command or set its defaultsno
Message digest authentication password (key)message-digest-key
Key IDkeyid
Use MD5 algorithmmd5
OSPF password (key)key
Command Mode
• /exec/configure/router-ospf/vrf/router-ospf-slink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3058
M Commandsmessage-digest-key md5
Page 3203
metric-style transition[no] metric-style { transition }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure metric style used in advertised LSPsmetric-style
Use both narrow and wide metric styletransition
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3059
M Commandsmetric-style transition
Page 3204
metric-type[no] metric-type <metric-type>
Syntax Description
(Optional) Negate a command or set its defaultsno
Identifying name of metric with max 128 charactersmetric-type
Supported metric-types te,igpmetric-type
Command Mode
• /exec/configure/sr/te/color
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3060
M Commandsmetric-type
Page 3205
metric direct 0[no] metric direct 0
Syntax Description
(Optional) Negate a command or set its defaultsno
Cost of direct routesmetric
Cost of direct routesdirect
direct route cost is zero to be compatible with IOS0
Command Mode
• /exec/configure/router-rip
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3061
M Commandsmetric direct 0
Page 3206
metric maximum-hops{ { metric maximum-hops <hops> } | { no metric maximum-hops [ <hops> ] } }
Syntax Description
Negate a command or set its defaultsno
Modify EIGRP routing metrics and parametersmetric
Advertise EIGRP routes greater than <hops> as unreachablemaximum-hops
Hop counthops
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3062
M Commandsmetric maximum-hops
Page 3207
metric rib-scale{ { metric rib-scale <ribscale> } | { no metric rib-scale [ <ribscale> ] } }
Syntax Description
Negate a command or set its defaultsno
Modify EIGRP routing metrics and parametersmetric
Defines RIB scaling valuerib-scale
Rib scaleribscale
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3063
M Commandsmetric rib-scale
Page 3208
metric version 64bit{ { metric version 64bit } | { no metric version [ 64bit ] } }
Syntax Description
Negate a command or set its defaultsno
Modify EIGRP routing metrics and parametersmetric
Modify EIGRP metric versionversion
64 bit metric version64bit
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3064
M Commandsmetric version 64bit
Page 3209
metric weights{ { metric weights <tos> <k1> <k2> <k3> <k4> <k5> [ <k6> ] } | { no metric weights [ <tos> <k1> <k2><k3> <k4> <k5> [ <k6> ] ] } }
Syntax Description
Negate a command or set its defaultsno
Modify EIGRP routing metrics and parametersmetric
Modify EIGRP metric coefficientsweights
Type Of Service (Only TOS 0 supported)tos
K1k1
K2k2
K3k3
K4k4
K5k5
(Optional) K6k6
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3065
M Commandsmetric weights
Page 3210
mkdirmkdir <uri0>
Syntax Description
Create new directorymkdir
Directory nameuri0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3066
M Commandsmkdir
Page 3211
mode[no] mode <mode-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Hot-standby modemode
Node Modemode-id
Command Mode
• /exec/configure/itd-dg-node
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3067
M Commandsmode
Page 3212
mode[no] mode <vmode>
Syntax Description
(Optional) Negate a command or set its defaultsno
Operational mode of the VLANmode
vmode
Command Mode
• /exec/configure/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3068
M Commandsmode
Page 3213
mode[no] mode <mode-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Hot-standby mode for a nodemode
Mode of nodemode-id
Command Mode
• /exec/configure/plb-dg-node
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3069
M Commandsmode
Page 3214
mode tap-aggregation[no] mode tap-aggregation [ { vlan <vlan_id> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure the interface operational modemode
Disable/Enable tap aggregation on the interfacetap-aggregation
(Optional) vlan that is to be tagged in outgoing packetsvlan
(Optional) Vlan IDvlan_id
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3070
M Commandsmode tap-aggregation
Page 3215
module transceiver-frequency[no] module <module> transceiver-frequency { <xcvr_frequency> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure for modulemodule
Enter module numbermodule
Configure X2 transceiver frequency typetransceiver-frequency
Enter transceiver frequency typexcvr_frequency
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3071
M Commandsmodule transceiver-frequency
Page 3216
monitor erspan granularity[no] monitor erspan granularity { 100_us | 100_ns | 1588 | ns }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Ethernet SPAN sessionsmonitor
Configure Ethernet ERSPAN sessionserspan
Configure granularity for ERSPAN Type III sessionsgranularity
100 microseconds100_us
100 nanoseconds100_ns
1588 in seconds/nanoseconds1588
nanosecondsns
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3072
M Commandsmonitor erspan granularity
Page 3217
monitor erspan origin ip-address[no] monitor erspan origin ip-address <ip> [ global ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Ethernet SPAN sessionsmonitor
Configure Ethernet ERSPAN sessionserspan
Configure the erspan origin ip addressorigin
Configure global origin IP addressip-address
ip
(Optional) Configure in default VDC across all VDCsglobal
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3073
M Commandsmonitor erspan origin ip-address
Page 3218
monitor erspan switch-id[no] monitor erspan switch-id <switch_id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Ethernet SPAN sessionsmonitor
Configure Ethernet ERSPAN sessionserspan
Configure the erspan switch-idswitch-id
erspan-switch-idswitch_id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3074
M Commandsmonitor erspan switch-id
Page 3219
monitor sessionmonitor session <session_number> [ type local ]
Syntax Description
Configure Ethernet SPAN sessionsmonitor
Configure session preferencessession
session_number
(Optional) Specify a session typetype
(Optional) Create a local sessionlocal
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3075
M Commandsmonitor session
Page 3220
monitor session shut[no] monitor session { all | <session_range> } [ shut ] | monitor session { all | <session_range> } shut
Syntax Description
Negate a command or set its defaultsno
Configure Ethernet SPAN sessionsmonitor
Configure session preferencessession
All sessionsall
session_range
(Optional) Shut the selected sessionshut
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3076
M Commandsmonitor session shut
Page 3221
monitor session type acl-capturemonitor session <session_number> type acl-capture
Syntax Description
Configure Ethernet SPAN sessionsmonitor
Configure session preferencessession
session_number
Specify a session typetype
Create an acl-capture sessionacl-capture
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3077
M Commandsmonitor session type acl-capture
Page 3222
monitor session type erspan-destinationmonitor session <session_number> type erspan-destination
Syntax Description
Configure Ethernet SPAN sessionsmonitor
Configure session preferencessession
session_number
Specify a session typetype
Create an erspan destination sessionerspan-destination
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3078
M Commandsmonitor session type erspan-destination
Page 3223
monitor session type erspan-sourcemonitor session <session_number> type erspan-source
Syntax Description
Configure Ethernet SPAN sessionsmonitor
Configure session preferencessession
session_number
Specify a session typetype
Create an erspan source sessionerspan-source
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3079
M Commandsmonitor session type erspan-source
Page 3224
monitor session warp[no] monitor session warp
Syntax Description
Negate a command or set its defaultsno
Configure Ethernet SPAN sessionsmonitor
Configure session preferencessession
Configure Warp span modewarp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3080
M Commandsmonitor session warp
Page 3225
monitor session warpmonitor session warp [ type local ]
Syntax Description
Configure Ethernet SPAN sessionsmonitor
Configure session preferencessession
Create warp sessionwarp
(Optional) Specify a session typetype
(Optional) Create a local sessionlocal
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3081
M Commandsmonitor session warp
Page 3226
mountmount { usb1: | usb2: }
Syntax Description
mount expansion flash or USB storagemount
mount USB drive in port 1usb1:
mount USB drive in port 2usb2:
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3082
M Commandsmount
Page 3227
mount slot0mount slot0:
Syntax Description
mount expansion flash or USB storagemount
mount expansion flashslot0:
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3083
M Commandsmount slot0
Page 3228
movemove <uri0> <uri1>
Syntax Description
Move filesmove
Source file pathuri0
Destination file pathuri1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3084
M Commandsmove
Page 3229
mst designated prioritymst <mst-id> designated priority <prio> | no mst <mst-id> designated priority [ <prio> ]
Syntax Description
Negate a command or set its defaultsno
Multiple spanning tree configurationmst
MST instance range, example: 0-3,5,7-9mst-id
Set the designated bridge priority for the spanning treedesignated
Set the bridge priority for the spanning treepriority
bridge priority in increments of 4096prio
Command Mode
• /exec/configure/spanning-tree/pseudo
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3085
M Commandsmst designated priority
Page 3230
mst root prioritymst <mst-id> root priority <prio> | no mst <mst-id> root priority [ <prio> ]
Syntax Description
Negate a command or set its defaultsno
Multiple spanning tree configurationmst
MST instance range, example: 0-3,5,7-9mst-id
Set the root bridge priority for the spanning treeroot
Set the bridge priority for the spanning treepriority
bridge priority in increments of 4096prio
Command Mode
• /exec/configure/spanning-tree/pseudo
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3086
M Commandsmst root priority
Page 3231
mtracemtrace <source> [ <receiver> ] [ <group> ] [ vrf <vrf-known-name> ]
Syntax Description
Tracemtrace
IPsource
(Optional) IPreceiver
(Optional) IPgroup
(Optional) VRFvrf
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3087
M Commandsmtrace
Page 3232
mtumtu <mtu_val> | no mtu [ <mtu_val> ]
Syntax Description
Negate a command or set its defaultsno
Configure mtu for the portmtu
mtu_val
Command Mode
• /exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p /exec/configure/if-port-channel-sub/exec/configure/if-sub /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member/exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3088
M Commandsmtu
Page 3233
mtu1[no] mtu1 <value>
Syntax Description
(Optional) Negate a command or set its defaultsno
MTU for the CoSmtu1
MTU valuevalue
Command Mode
• /exec/configure/policy-map/type/uf/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3089
M Commandsmtu1
Page 3234
mtumtu <mtu_value> | no mtu
Syntax Description
Negate a command or set its defaultsno
Set the MTU size for SPAN packetsmtu
mtu_value
Command Mode
• /exec/configure/monitor-local-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3090
M Commandsmtu
Page 3235
mtumtu <mtu_value> | no mtu
Syntax Description
Negate a command or set its defaultsno
Set the MTU size for ERSPAN packetsmtu
mtu_value
Command Mode
• /exec/configure/monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3091
M Commandsmtu
Page 3236
mtumtu <mtu-val> | no mtu [ <mtu-val> ]
Syntax Description
Negate a command or set its defaultsno
Configure MTUmtu
Bytesmtu-val
Command Mode
• /exec/configure/if-any-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3092
M Commandsmtu
Page 3237
mtu[no] mtu <value>
Syntax Description
(Optional) Negate a command or set its defaultsno
MTU for the CoSmtu
MTU valuevalue
Command Mode
• /exec/configure/policy-map/type/uf/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3093
M Commandsmtu
Page 3238
mtu[no] mtu <mtu>
Syntax Description
MTUmtu
MTU port to be configuredmtu
Command Mode
• /exec/configure/config-ssx-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3094
M Commandsmtu
Page 3239
mtumtu <mtu_val> | no mtu
Syntax Description
Negate a command or set its defaultsno
Set the interface Maximum Transmission Unit (MTU)mtu
MTU size in bytesmtu_val
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3095
M Commandsmtu
Page 3240
multi-topology[no] multi-topology [ transition ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable multitopoloy for IPV6multi-topology
(Optional) Configure multitopology transition modetransition
Command Mode
• /exec/configure/router-isis/router-isis-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3096
M Commandsmulti-topology
Page 3241
multicast[no] multicast <mode_enum>
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable multicast best-effortmulticast
mode_enum
Command Mode
• /exec/configure/monitor-local-src /exec/configure/config-monitor/exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3097
M Commandsmulticast
Page 3242
multisite border-gateway interface[no] multisite border-gateway interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
VxLAN Multisitemultisite
VxLAN Multisite Border-gatewayborder-gateway
NVE Multisite Border-gateway Interfaceinterface
interface
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3098
M Commandsmultisite border-gateway interface
Page 3243
multisite ingress-replication[no] multisite ingress-replication
Syntax Description
(Optional) Negate a command or set its defaultsno
multisite ingress replicationmultisite
Configure ingress replicationingress-replication
Command Mode
• /exec/configure/if-nve/vni
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3099
M Commandsmultisite ingress-replication
Page 3244
mvr-config[no] mvr-config
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable IGMP MVRmvr-config
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3100
M Commandsmvr-config
Page 3245
mvr-group[no] mvr-group { { <ip-addr> <ip-mask> } [ { vlan <vlan-id> } ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
MVR interface configmvr-group
Group IP Addressip-addr
IP network mask in format m.m.m.mip-mask
(Optional) Global default MVR vlanvlan
(Optional) Enter MVR Vlanvlan-id
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-eth-port-channel-switch/exec/configure/if-ethernet-p2p-switch /exec/configure/if-remote-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3101
M Commandsmvr-group
Page 3246
mvr-group[no] mvr-group { { <ip-addr> } [ { vlan <vlan-id> } ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
MVR Groupmvr-group
Group IP Addressip-addr
(Optional) Global default MVR vlanvlan
(Optional) Enter MVR Vlanvlan-id
Command Mode
• /exec/configure/igmp-mvr-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3102
M Commandsmvr-group
Page 3247
mvr-group[no] mvr-group { { <ip-addr> count <count> } [ { vlan <vlan-id> } ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
MVR Groupmvr-group
Group IP Addressip-addr
Number of contiguous groupscount
Number of contiguos groupscount
(Optional) Global default MVR vlanvlan
(Optional) Enter MVR Vlanvlan-id
Command Mode
• /exec/configure/igmp-mvr-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3103
M Commandsmvr-group
Page 3248
mvr-group[no] mvr-group { { <ip-addr> <ip-mask> } [ { vlan <vlan-id> } ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
MVR Groupmvr-group
Group IP Addressip-addr
IP network mask in format m.m.m.mip-mask
(Optional) Global default MVR vlanvlan
(Optional) Enter MVR Vlanvlan-id
Command Mode
• /exec/configure/igmp-mvr-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3104
M Commandsmvr-group
Page 3249
mvr-group[no] mvr-group { { <ip-prefix> } [ { vlan <vlan-id> } ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
MVR Groupmvr-group
IP prefix and network mask length in format x.x.x.x/mip-prefix
(Optional) Global default MVR vlanvlan
(Optional) Enter MVR Vlanvlan-id
Command Mode
• /exec/configure/igmp-mvr-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3105
M Commandsmvr-group
Page 3250
mvr-group[no] mvr-group { { <ip-addr> } [ { vlan <vlan-id> } ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
MVR interface configmvr-group
Group IP Addressip-addr
(Optional) Global default MVR vlanvlan
(Optional) Enter MVR Vlanvlan-id
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-eth-port-channel-switch/exec/configure/if-ethernet-p2p-switch /exec/configure/if-remote-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3106
M Commandsmvr-group
Page 3251
mvr-group[no] mvr-group { { <ip-addr> count <count> } [ { vlan <vlan-id> } ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
MVR interface configmvr-group
Group IP Addressip-addr
Number of contiguous groupscount
Number of contiguos groupscount
(Optional) Global default MVR vlanvlan
(Optional) Enter MVR Vlanvlan-id
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-eth-port-channel-switch/exec/configure/if-ethernet-p2p-switch /exec/configure/if-remote-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3107
M Commandsmvr-group
Page 3252
mvr-group[no] mvr-group { { <ip-prefix> } [ { vlan <vlan-id> } ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
MVR interface configmvr-group
IP prefix and network mask length in format x.x.x.x/mip-prefix
(Optional) Global default MVR vlanvlan
(Optional) Enter MVR Vlanvlan-id
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-eth-port-channel-switch/exec/configure/if-ethernet-p2p-switch /exec/configure/if-remote-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3108
M Commandsmvr-group
Page 3253
mvr-suppress-query vlan{ { mvr-suppress-query vlan <vlan-range> } | { no mvr-suppress-query } }
Syntax Description
Negate a command or set its defaultsno
Suppress IGMP General query forwarding from vlansmvr-suppress-query
MVR Vlan Id or rangesvlan
VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19vlan-range
Command Mode
• /exec/configure/igmp-mvr-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3109
M Commandsmvr-suppress-query vlan
Page 3254
mvr-type receiver[no] mvr-type receiver
Syntax Description
(Optional) Negate a command or set its defaultsno
MVR interface configmvr-type
Mvr receiver portreceiver
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-eth-port-channel-switch/exec/configure/if-ethernet-p2p-switch /exec/configure/if-remote-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3110
M Commandsmvr-type receiver
Page 3255
mvr-type source[no] mvr-type source
Syntax Description
(Optional) Negate a command or set its defaultsno
MVR interface configmvr-type
Mvr source portsource
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-eth-port-channel-switch/exec/configure/if-ethernet-p2p-switch /exec/configure/if-remote-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3111
M Commandsmvr-type source
Page 3256
mvr-vlan[no] mvr-vlan <vlan-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Global default MVR vlanmvr-vlan
Enter MVR Vlanvlan-id
Command Mode
• /exec/configure/igmp-mvr-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3112
M Commandsmvr-vlan
Page 3257
mvr-vlan{ { no mvr-vlan <vlan-id> } | { mvr-vlan <vlan-id> } }
Syntax Description
Negate a command or set its defaultsno
Interface MVR Configmvr-vlan
Enter MVR Vlanvlan-id
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-eth-port-channel-switch/exec/configure/if-ethernet-p2p-switch /exec/configure/if-remote-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3113
M Commandsmvr-vlan
Page 3258
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3114
M Commandsmvr-vlan
Page 3259
N Commands
• name-lookup, on page 3118• name-lookup, on page 3119• name, on page 3120• name, on page 3121• name, on page 3122• nat destination, on page 3123• nbm external-link, on page 3124• nbm flow-policy, on page 3125• nbm flow acceptance-mode guaranteed nbm flow acceptance-mode, on page 3126• nbm flow asm range, on page 3127• nbm flow bandwidth kbps mbps gbps, on page 3128• nbm flow dscp, on page 3129• nbm host-policy, on page 3130• nbm mode pim-active, on page 3131• nbm reserve unicast fabric bandwidth, on page 3132• negotiate auto, on page 3133• negotiate auto 25000, on page 3134• neighbor-down fib-accelerate, on page 3135• neighbor, on page 3136• neighbor, on page 3137• neighbor, on page 3138• neighbor, on page 3139• neighbor, on page 3140• neighbor maximum-prefix, on page 3141• nemo config address port interval, on page 3142• net, on page 3143• net, on page 3144• net, on page 3145• network, on page 3146• network, on page 3147• network, on page 3148• network, on page 3149• next-address exclude-address, on page 3150
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3115
Page 3260
• next-hop-self, on page 3151• next-hop-self, on page 3152• next-hop-third-party, on page 3153• next-hop-third-party, on page 3154• next-hop out-label explicit-null implicit-null next-hop auto-resolve out-label explicit-null implicit-null,on page 3155
• next-hop out-label explicit-null implicit-null next-hop auto-resolve out-label explicit-null implicit-null,on page 3156
• nexthop route-map, on page 3157• nexthop trigger-delay critical non-critical, on page 3158• ngoam authentication-key, on page 3159• ngoam connect-check, on page 3160• ngoam install acl, on page 3161• ngoam profile, on page 3162• ngoam xconnect hb-interval, on page 3163• no-more, on page 3164• no, on page 3165• no, on page 3166• no, on page 3167• no, on page 3168• no, on page 3169• no, on page 3170• no, on page 3171• no, on page 3174• no, on page 3179• no, on page 3183• no, on page 3186• no, on page 3189• no, on page 3192• no, on page 3195• no, on page 3198• no, on page 3201• no, on page 3203• no, on page 3204• no, on page 3205• no, on page 3206• node, on page 3207• node, on page 3208• node, on page 3209• node ip, on page 3210• node ip, on page 3211• npiv enable, on page 3212• npv auto-load-balance disruptive, on page 3213• npv traffic-map server-interface external-interface, on page 3214• nsf await-redist-proto-convergence, on page 3215• ntp access-group, on page 3216
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3116
N Commands
Page 3261
• ntp access-group match-all, on page 3217• ntp allow private, on page 3218• ntp authenticate, on page 3219• ntp authentication-key md5, on page 3220• ntp drop-aged-packet, on page 3221• ntp logging, on page 3222• ntp master, on page 3223• ntp passive, on page 3224• ntp peer, on page 3225• ntp rts-update, on page 3226• ntp server, on page 3227• ntp source-interface, on page 3228• ntp source, on page 3229• ntp sync-retry, on page 3230• ntp trusted-key, on page 3231• nv overlay evpn, on page 3232• nxapi certificate, on page 3233• nxapi flow, on page 3234• nxapi http port, on page 3235• nxapi ssl ciphers weak, on page 3236• nxapi ssl protocols, on page 3237• nxapi use-vrf management default, on page 3238• nxsdk enable app, on page 3239• nxsdk service-name, on page 3240
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3117
N Commands
Page 3262
name-lookup[no] name-lookup
Syntax Description
(Optional) Negate a command or set its defaultsno
Display OSPF router ids as DNS namesname-lookup
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3118
N Commandsname-lookup
Page 3263
name-lookup[no] name-lookup
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable Name Lookup for OSPF Neighborsname-lookup
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3119
N Commandsname-lookup
Page 3264
namename [ <name> ] | no name
Syntax Description
Negate a command or set its defaultsno
Redundancy name stringname
(Optional) name stringname
Command Mode
• /exec/configure/if-eth-any/hsrp_ipv4 /exec/configure/if-eth-any/hsrp_ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3120
N Commandsname
Page 3265
namename <name-val> | no name [ <name-val> ]
Syntax Description
Negate a command or set its defaultsno
Set configuration namename
Configuration namename-val
Command Mode
• /exec/configure/spanning-tree/mst/configuration
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3121
N Commandsname
Page 3266
namename <vlan-name> | no name
Syntax Description
Negate a command or set its defaultsno
Ascii name of the VLANname
The ascii name for the VLANvlan-name
Command Mode
• /exec/configure/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3122
N Commandsname
Page 3267
nat destination{ nat destination } | { no nat destination }
Syntax Description
Negate a command or set its defaultsno
Network Address Translationnat
Destination NATdestination
Command Mode
• /exec/configure/plb
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3123
N Commandsnat destination
Page 3268
nbm external-link[no] nbm external-link
Syntax Description
Non Blocking Multicastnbm
link connected to external router. Configuring this will flap the interfaceexternal-link
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3124
N Commandsnbm external-link
Page 3269
nbm flow-policy[no] nbm flow-policy
Syntax Description
(Optional) Negate a command or set its defaultsno
Non Blocking Multicastnbm
Flow Policy Characteristicsflow-policy
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3125
N Commandsnbm flow-policy
Page 3270
nbm flow acceptance-mode guaranteed nbm flowacceptance-mode
{ nbm flow acceptance-mode { guaranteed | best-fit } } | [ no ] nbm flow acceptance-mode
Syntax Description
Non Blocking Multicastnbm
Flow Characteristicsflow
Flow Acceptance Modeacceptance-mode
New flows are guaranteed to be acceptedguaranteed
New flows are best-fit among fabric linksbest-fit
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3126
N Commandsnbm flow acceptance-mode guaranteed nbm flow acceptance-mode
Page 3271
nbm flow asm range[no] nbm flow asm range <group> +
Syntax Description
Non Blocking Multicastnbm
Flow Characteristicsflow
Any-Source Multicast (ASM) groupsasm
Configure explicit group rangesrange
List of group range prefixesgroup
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3127
N Commandsnbm flow asm range
Page 3272
nbm flow bandwidth kbps mbps gbps{ nbm flow bandwidth { <val_kbps> kbps | <val_mbps>mbps | <val_gbps> gbps } } | { no nbm flow bandwidth}
Syntax Description
Non Blocking Multicastnbm
Flow Characteristicsflow
Bandwidth per flowbandwidth
Per Flow Bandwidth in Kbpsval_kbps
Bandwidth value in Kbpskbps
Per Flow Bandwidth in Mbpsval_mbps
Bandwidth value in Mbpsmbps
Per Flow Bandwidth in Gbpsval_gbps
Bandwidth value in Gbpsgbps
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3128
N Commandsnbm flow bandwidth kbps mbps gbps
Page 3273
nbm flow dscp{ nbm flow dscp <val_dscp> } | { no nbm flow dscp }
Syntax Description
Non Blocking Multicastnbm
Flow Characteristicsflow
DSCP for the flowdscp
Integer valueval_dscp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3129
N Commandsnbm flow dscp
Page 3274
nbm host-policy[no] nbm host-policy
Syntax Description
(Optional) Negate a command or set its defaultsno
Non Blocking Multicastnbm
NBM SW Host Admission Policyhost-policy
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3130
N Commandsnbm host-policy
Page 3275
nbm mode pim-active[no] nbm mode pim-active [ __readonly__ <output> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Non Blocking Multicastnbm
Set pmn modemode
Bandwidth engine running in fabricpim-active
(Optional)__readonly__
(Optional)output
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3131
N Commandsnbm mode pim-active
Page 3276
nbm reserve unicast fabric bandwidthnbm reserve unicast fabric bandwidth <percentage> | no nbm reserve unicast fabric bandwidth
Syntax Description
Negate a command or set its defaultsno
Non Blocking Multicastnbm
reserve bandwidthreserve
unicastunicast
fabricfabric
percentage of bandwidth for unicast flowbandwidth
percentage valuepercentage
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3132
N Commandsnbm reserve unicast fabric bandwidth
Page 3277
negotiate autonegotiate auto | no negotiate auto
Syntax Description
Negate a command or set its defaultsno
Configure link negotiation parametersnegotiate
Configure auto-negotiationauto
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3133
N Commandsnegotiate auto
Page 3278
negotiate auto 25000[no] negotiate auto 25000
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure link negotiation parametersnegotiate
Configure auto-negotiationauto
Force auto-negotiate to only 25000 and change fec to auto25000
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3134
N Commandsnegotiate auto 25000
Page 3279
neighbor-down fib-accelerate[no] neighbor-down fib-accelerate
Syntax Description
(Optional) Negate a command or set its defaultsno
Handle BGP neighbor down event, due to various reasonsneighbor-down
Accelerate the hardware updates for IP/IPv6 adjacencies for neighborfib-accelerate
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3135
N Commandsneighbor-down fib-accelerate
Page 3280
neighborneighbor [ vrf { <vrf-name> | <vrf-known-name> } ] <ipaddr> { implicit-withdraw | labels accept <pfx-list>| targeted } | no neighbor [ vrf { <vrf-name> | <vrf-known-name> } ] <ipaddr> [ implicit-withdraw | labelsaccept | targeted ]
Syntax Description
Negate a command or set its defaultsno
Configure neighbor parametersneighbor
(Optional) VRF Routing/Forwarding instance informationvrf
(Optional) VPN Routing/Forwarding instance namevrf-name
(Optional) Known VRF namevrf-known-name
IP address for LDP neighboripaddr
Enable LDP Implicit Withdraw Labelimplicit-withdraw
Configure label binding exchange controlslabels
Specify label bindings to acceptaccept
Name of prefix listpfx-list
Establish targeted sessiontargeted
Command Mode
• /exec/configure/ldp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3136
N Commandsneighbor
Page 3281
neighbor[no] neighbor { <neighbor-id> | <ipv6-neighbor-id> } [ remote-as <asn> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a BGP neighborneighbor
IP address of the neighborneighbor-id
(Optional) Specify Autonomous System Number of the neighborremote-as
(Optional) Autonomous System Numberasn
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3137
N Commandsneighbor
Page 3282
neighbor[no] neighbor { <neighbor-id> | <ipv6-neighbor-id> } [ remote-as <asn> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a BGP neighborneighbor
IP address of the neighborneighbor-id
(Optional) Specify Autonomous System Number of the neighborremote-as
(Optional) Autonomous System Numberasn
Command Mode
• /exec/configure/router-bgp/router-bgp-vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3138
N Commandsneighbor
Page 3283
neighbor[no] neighbor { <neighbor-prefix> | <ipv6-neighbor-prefix> } [ remote-as [ <asn> | route-map <rmap-name>] ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a BGP neighborneighbor
IP prefix for neighborsneighbor-prefix
(Optional) Specify Autonomous System Number of the neighborremote-as
(Optional) Autonomous System Numberasn
(Optional) Route-map to match prefix peer AS numberroute-map
(Optional) Route-map namermap-name
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3139
N Commandsneighbor
Page 3284
neighbor[no] neighbor { <neighbor-prefix> | <ipv6-neighbor-prefix> } [ remote-as [ <asn> | route-map <rmap-name>] ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a BGP neighborneighbor
IP prefix for neighborsneighbor-prefix
(Optional) Specify Autonomous System Number of the neighborremote-as
(Optional) Autonomous System Numberasn
(Optional) Route-map to match prefix peer AS numberroute-map
(Optional) Route-map namermap-name
Command Mode
• /exec/configure/router-bgp/router-bgp-vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3140
N Commandsneighbor
Page 3285
neighbor maximum-prefix{ { neighbor <address> { <interface> | maximum-prefix <value> [ warning-only ] } } | { no neighbor <address>[ <interface> | maximum-prefix <value> [ warning-only ] ] } } | { { neighbor maximum-prefix <value> [<threshold> ] [ warning-only ] [ restart <time1> ] [ restart-count <count> ] [ reset-time <time2> ] [ dampened] } | { no neighbor maximum-prefix [ <value> [ <threshold> ] [ warning-only ] [ restart <time1> ] [ restart-count<count> ] ] } }
Syntax Description
Negate a command or set its defaultsno
Specify a neighbor routerneighbor
Interfaceinterface
Neighbor addressaddress
Maximum number of IP prefixes acceptable from a neighbormaximum-prefix
Number of IP prefixes for maximum-prefix limitvalue
(Optional) Threshold value (%) at which to generate a warning messagethreshold
(Optional) Only give warning message when limit is exceededwarning-only
(Optional) Duration for which a prefix source is ignoredrestart
(Optional) Restart interval in minutestime1
(Optional) Number of times sessions are auto-restartedrestart-count
(Optional) Number of timescount
(Optional) Duration after which restart history is clearedreset-time
(Optional) Reset time in minutestime2
(Optional) Exponentially increase restart time intervaldampened
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3141
N Commandsneighbor maximum-prefix
Page 3286
nemo config address port interval[no] nemo config address <ip_address> port <portnum> interval <interval-num>
Syntax Description
(Optional) Negate a command or set its defaultsno
Nemo switch onboarding enablernemo
Configure Nemo for switch onboardingconfig
IP address of the Nemo platformaddress
IP Addressip_address
Port number of the Nemo platformport
Port numberportnum
Config interval in millisecondinterval
Config interval in millisecondinterval-num
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3142
N Commandsnemo config address port interval
Page 3287
net[no] net <net>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Network Entity Title for IS-ISnet
NET in form of XX.XXXX. ... .XXXX[.00]net
Command Mode
• /exec/configure/otv-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3143
N Commandsnet
Page 3288
net[no] net <net>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Network Entity Title for IS-ISnet
NET in form of XX.XXXX. ... .XXXX[.00]net
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3144
N Commandsnet
Page 3289
net[no] net <net>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Network Entity Title for IS-ISnet
NET in form of XX.XXXX. ... .XXXX[.00]net
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3145
N Commandsnet
Page 3290
network[no] network { { <address> <mask> } | <prefix> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable routing on an IP networknetwork
Network numberaddress
EIGRP wild card bitsmask
IP prefix in slash formatprefix
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3146
N Commandsnetwork
Page 3291
network[no] network { <ip-dest> <ip-mask> | <ip-prefix> }
Syntax Description
(Optional) Negate a command or set its defaultsno
RIP IP networknetwork
IP addr formatip-dest
IP network mask formatip-mask
Exact prefixip-prefix
Command Mode
• /exec/configure/router-rip/router-rip-af-ipv4 /exec/configure/router-rip/router-rip-vrf-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3147
N Commandsnetwork
Page 3292
network[no] network { <ip-addr> mask <ip-mask> | <ip-prefix> } [ route-map <rmap-name> | summarize | evpn ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an IP prefix to advertisenetwork
IP network to advertiseip-addr
Configure the mask of the IP prefix to advertisemask
Dotted 4-octet maskip-mask
IP prefix in CIDR formatip-prefix
(Optional) Apply route-map to modify attributesroute-map
(Optional) Route-map namermap-name
(Optional) Summarize more specific prefixes from routing tablesummarize
(Optional) Only advertise route towards evpn sideevpn
Command Mode
• /exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3148
N Commandsnetwork
Page 3293
network[no] network <ipv6-prefix> [ route-map <rmap-name> | summarize ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure an IPv6 prefix to advertisenetwork
(Optional) Apply route-map to modify attributesroute-map
(Optional) Route-map namermap-name
(Optional) Summarize more specific prefixes from routing tablesummarize
Command Mode
• /exec/configure/router-bgp/router-bgp-af-ipv6 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3149
N Commandsnetwork
Page 3294
next-address exclude-address{ next-address [ loose | strict ] <ipaddr> | exclude-address <ipaddr> }
Syntax Description
Specify the next address in the pathnext-address
(Optional) Target address is looseloose
(Optional) Target address is strictstrict
Exclude an address from subsequent partial path segmentsexclude-address
Enter IP address (A.B.C.D)ipaddr
Command Mode
• /exec/configure/te/expl-path
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3150
N Commandsnext-address exclude-address
Page 3295
next-hop-self[ no | default ] next-hop-self
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Set our peering address as nexthopnext-hop-self
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3151
N Commandsnext-hop-self
Page 3296
next-hop-self[ no | default ] next-hop-self
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Set our peering address as nexthopnext-hop-self
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3152
N Commandsnext-hop-self
Page 3297
next-hop-third-party[ no | default ] next-hop-third-party
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Compute a third-party nexthop if possiblenext-hop-third-party
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3153
N Commandsnext-hop-third-party
Page 3298
next-hop-third-party[ no | default ] next-hop-third-party
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Compute a third-party nexthop if possiblenext-hop-third-party
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3154
N Commandsnext-hop-third-party
Page 3299
next-hop out-label explicit-null implicit-null next-hopauto-resolve out-label explicit-null implicit-null
[no] { next-hop [ backup <interface> ] <next-hop> out-label { <static-outlabel> | explicit-null | implicit-null} | next-hop auto-resolve out-label { <static-outlabel> | explicit-null | implicit-null } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Nexthopnext-hop
Destination IPv4 next hopnext-hop
Label Valuestatic-outlabel
(Optional) Back up interfaceinterface
Output labelout-label
IETF MPLS IPv4 explicit null label (0)explicit-null
IETF MPLS implicit null label (3)implicit-null
auto resolve the destination pathauto-resolve
(Optional) Backup destinationbackup
Command Mode
• /exec/configure/mpls_static/ipv4/input
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3155
N Commandsnext-hop out-label explicit-null implicit-null next-hop auto-resolve out-label explicit-null implicit-null
Page 3300
next-hop out-label explicit-null implicit-null next-hopauto-resolve out-label explicit-null implicit-null
[no] { next-hop [ backup <interface> ] <ipv6-next-hop> out-label { <static-outlabel> | explicit-null | implicit-null} | next-hop auto-resolve out-label { <static-outlabel> | explicit-null | implicit-null } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Nexthopnext-hop
Label Valuestatic-outlabel
(Optional) Back up interfaceinterface
Output labelout-label
IETF MPLS IPv6 explicit null label (2)explicit-null
IETF MPLS implicit null label (3)implicit-null
auto resolve the destination pathauto-resolve
(Optional) Backup destinationbackup
Command Mode
• /exec/configure/mpls_static/ipv6/input
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3156
N Commandsnext-hop out-label explicit-null implicit-null next-hop auto-resolve out-label explicit-null implicit-null
Page 3301
nexthop route-map[no] nexthop route-map <rmap-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Nexthop trackingnexthop
Route map for valid nexthopsroute-map
Route-map namermap-name
Command Mode
• /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-af-link-state /exec/configure/router-bgp/router-bgp-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-af-ipv6-mvpn /exec/configure/router-bgp/router-bgp-af-ipv4-mdt/exec/configure/router-bgp/router-bgp-af-l2vpn-vpls
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3157
N Commandsnexthop route-map
Page 3302
nexthop trigger-delay critical non-critical{ nexthop trigger-delay critical <criticaldelay> non-critical <noncriticaldelay> } | { no nexthop trigger-delay}
Syntax Description
Negate a command or set its defaultsno
Nexthop trackingnexthop
Set the delay to trigger nexthop trackingtrigger-delay
Nexthop changes affecting reachabilitycritical
Other nexthop changesnon-critical
Delay value (miliseconds)noncriticaldelay
Delay value (miliseconds)criticaldelay
Command Mode
• /exec/configure/router-bgp/router-bgp-af /exec/configure/router-bgp/router-bgp-af-ipv4-mdt/exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-vpnv6/exec/configure/router-bgp/router-bgp-af-link-state /exec/configure/router-bgp/router-bgp-af-l2vpn-vpls/exec/configure/router-bgp/router-bgp-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-af-ipv6-mvpn/exec/configure/router-bgp/router-bgp-af-l2vpn-evpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3158
N Commandsnexthop trigger-delay critical non-critical
Page 3303
ngoam authentication-key{ ngoam authentication-key <value> } | { no ngoam authentication-key [ <value> ] }
Syntax Description
Negate a command or set its defaultsno
Configure ngoamngoam
Ngoam authentication-keyauthentication-key
authentication keyvalue
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3159
N Commandsngoam authentication-key
Page 3304
ngoam connect-check[no] ngoam connect-check <id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure ngoamngoam
Configure ngoam oam connectivity checkconnect-check
connect check idid
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3160
N Commandsngoam connect-check
Page 3305
ngoam install acl[no] ngoam install acl
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure ngoamngoam
Ngoam installinstall
Ngoam install aclacl
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3161
N Commandsngoam install acl
Page 3306
ngoam profile[no] ngoam profile <profile-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure ngoamngoam
Configure ngoam oam profileprofile
ngoam profile idprofile-id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3162
N Commandsngoam profile
Page 3307
ngoam xconnect hb-interval{ ngoam xconnect hb-interval <ms> } | { no ngoam xconnect hb-interval [ <ms> ] }
Syntax Description
Negate a command or set its defaultsno
Configure ngoamngoam
Configure xconnect parametersxconnect
Configure xconnect heartbeat intervalhb-interval
interval in ms, 3 failures triggers failure default is 190ms
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3163
N Commandsngoam xconnect hb-interval
Page 3308
no-more| no-more
Syntax Description
Pipe command output to filter|
Turn-off pagination for command outputno-more
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3164
N Commandsno-more
Page 3309
no{ [ <seqno> ] | no } { <addr> <wild> | <prefix> | host <hostaddr> }
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
A.B.C.D Network address of object-group memberaddr
A.B.C.D wildcardwild
A.B.C.D/nn Network prefix of the object-group memberprefix
Host address of the object-group memberhost
A.B.C.D Host addresshostaddr
Command Mode
• /exec/configure/ipgroup
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3165
N Commandsno
Page 3310
no[no] { userprofile | trustedCert | CRLLookup | user-switch-bind | user-certdn-match | user-pubkey-match }
Syntax Description
Negate a command or set its defaultsno
Delete the userprofileuserprofile
Delete the trustedCerttrustedCert
Delete the CRLLookupCRLLookup
Delete the user-switch-binduser-switch-bind
Delete the certificate matchinguser-certdn-match
Delete the pubkey matchinguser-pubkey-match
Command Mode
• /exec/configure/ldap/search
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3166
N Commandsno
Page 3311
no[no] <seqno>
Syntax Description
Negate a command or set its defaultsno
Sequence numberseqno
Command Mode
• /exec/configure/arpacl /exec/configure/ipgroup /exec/configure/ipv6group /exec/configure/portgroup/exec/configure/timerange
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3167
N Commandsno
Page 3312
no[no] <seqno>
Syntax Description
Negate a command or set its defaultsno
Sequence numberseqno
Command Mode
• /exec/configure/macacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3168
N Commandsno
Page 3313
no[no] <seqno>
Syntax Description
Negate a command or set its defaultsno
Sequence numberseqno
Command Mode
• /exec/configure/mplsacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3169
N Commandsno
Page 3314
no[no] <seqno>
Syntax Description
Negate a command or set its defaultsno
Sequence numberseqno
Command Mode
• /exec/configure/ipacl /exec/configure/ipv6acl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3170
N Commandsno
Page 3315
no{ [ <seqno> ] | no } <permitdeny> { { { { ethertype <ethertypeid> } | { { ip | <proto> | <ip_other_proto> } {<src_any> | { <src_addr> <src_wild> } | <src_prefix> | { src_key_host <src_host> } | { src_key_addrgrp<src_addrgrp_name> } } { <dst_any> | { <dst_addr> <dst_wild> } | <dst_prefix> | { dst_key_host <dst_host>} | { dst_key_addrgrp <dst_addrgrp_name> } } { { [ [ fragments ] | [ log ] [ time-range <time_range_name>] | packet-length { <plen_op> <plen0> | <plen_range> <plen1> <plen2> } | { dscp { <dscp_num> | <dscp_str>} } | { ttl <ttl_num> } | { udf { <udf_name> <udf_val> <udf_mask> } + } ] } + | { [ [ fragments ] | [ log ] [time-range <time_range_name> ] | packet-length { <plen_op> <plen0> | <plen_range> <plen1> <plen2> } |{ tos { <tos_num> | <tos_str> } } | { precedence { <prec_num> | <prec_str> } } | { ttl <ttl_num> } | { udf {<udf_name> <udf_val> <udf_mask> } + } ] } + } [ capture session <session-id> ] } } [ vlan <vlanid> |ingress_intf { <intfid> | <intfname> } | vlan_priority <vlanpriorityid> ] + [ { udf { <udf_name> <udf_val><udf_mask> } + } ] } | { udf { <udf_name> <udf_val> <udf_mask> } + } } { [ <action> <actionid> ] } + [log ]
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Permit/denypermitdeny
Configure match based on ethertypeethertype
(Optional) Configure match based on vlanvlan
(Optional) Configure match based on ingress interfaceingress_intf
(Optional) Configure match based on priorityvlan_priority
Configure the ethertype valueethertypeid
(Optional) VLAN numbervlanid
(Optional) Interface indexintfid
(Optional) Interface nameintfname
(Optional) Vlan Priorityvlanpriorityid
Any IP protocolip
A protocol numberproto
ip_other_protoip_other_proto
Anysrc_any
Source network addresssrc_addr
Source wildcard bitssrc_wild
Source network prefixsrc_prefix
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3171
N Commandsno
Page 3316
A single source hostsrc_key_host
Source addresssrc_host
Source address groupsrc_key_addrgrp
Address group namesrc_addrgrp_name
Anydst_any
Destination network addressdst_addr
Destination wildcard bitsdst_wild
Destination network prefixdst_prefix
A single destination hostdst_key_host
Destination addressdst_host
Destination address groupdst_key_addrgrp
Address group namedst_addrgrp_name
(Optional) Match packets with given dscp valuedscp
(Optional) Differentiated services codepoint valuedscp_num
(Optional) Differentiated services codepoint labeldscp_str
(Optional) Match packets with given TOS valuetos
(Optional) Type of service valuetos_num
(Optional) Type of service labeltos_str
(Optional) Match packets with given precedence valueprecedence
(Optional) Precedence valueprec_num
(Optional) Precedence labelprec_str
(Optional) Check non-initial fragmentsfragments
(Optional) Log matches against this entrylog
(Optional) Specify a time rangetime-range
(Optional) Time range nametime_range_name
(Optional) Match packets based on layer 3 packet lengthpacket-length
(Optional) Packet-length operatorplen_op
(Optional) Packet-length rangeplen_range
(Optional) Packet lengthplen0
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3172
N Commandsno
Page 3317
(Optional) Lower packet lengthplen1
(Optional) Higher packet lengthplen2
(Optional) Match Packets with a given TTL valuettl
(Optional)ttl_num
(Optional) Enable packet capture on this filter for sessioncapture
(Optional) Session ID <1-48> for this sessionsession
(Optional) Session ID <1-48> for this sessionsession-id
(Optional) User defined field matchudf
(Optional) UDF nameudf_name
(Optional) UDF value to matchudf_val
(Optional) Mask to apply to UDF valueudf_mask
(Optional) Actionaction
(Optional) redirect: Ethernet1/1,port-channel1 set-erspan-dscp: <1-63>set-erspan-gre-proto: <1-65535>
actionid
Command Mode
• /exec/configure/ipacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3173
N Commandsno
Page 3318
no{ [ <seqno> ] | no } <permitdeny> { { ethertype <ethertypeid> } | { <proto_tcp> { { { { <src_any> | {<src_addr> <src_wild> } | <src_prefix> | { src_key_host <src_host> } | { src_key_addrgrp <src_addrgrp_name>} } [ { { <src_port_op> { <src_port0> | <src_port0_str> } } | { <src_port_range> { <src_port1> |<src_port1_str> } { <src_port2> | <src_port2_str> } } | src_portgroup <src_port_group> } ] { <dst_any> | {<dst_addr> <dst_wild> } | <dst_prefix> | { dst_key_host <dst_host> } | { dst_key_addrgrp <dst_addrgrp_name>} } [ { { <dst_port_op> { <dst_port0> | <dst_port0_str> } } | { <dst_port_range> { <dst_port1> |<dst_port1_str> } { <dst_port2> | <dst_port2_str> } } | dst_portgroup <dst_port_group> } ] { { [ urg | ack |psh | rst | syn | fin | established | [ log ] [ time-range <time_range_name> ] | packet-length { <plen_op> <plen0>| <plen_range> <plen1> <plen2> } | { dscp { <dscp_num> | <dscp_str> } } | { http-method { <opt_num> |<opt_str> } } | { tcp-option-length <tcp_opt_len> } | { tcp-flags-mask <tcp_flags_mask> } | { ttl <ttl_num>} ] } + | { [ urg | ack | psh | rst | syn | fin | established | [ log ] [ time-range <time_range_name> ] | packet-length{ <plen_op> <plen0> | <plen_range> <plen1> <plen2> } | { tos { <tos_num> | <tos_str> } } | { precedence{ <prec_num> | <prec_str> } } | { ttl <ttl_num> } ] } + } [ { udf { <udf_name> <udf_val> <udf_mask> } +} ] } | { { <src_any> | { <src_addr> <src_wild> } | <src_prefix> | { src_key_host <src_host> } | {src_key_addrgrp <src_addrgrp_name> } } { <dst_any> | { <dst_addr> <dst_wild> } | <dst_prefix> | {dst_key_host <dst_host> } | { dst_key_addrgrp <dst_addrgrp_name> } } { { [ [ fragments ] | [ log ] [ time-range<time_range_name> ] | packet-length { <plen_op> <plen0> | <plen_range> <plen1> <plen2> } | { dscp {<dscp_num> | <dscp_str> } } | { ttl <ttl_num> } | { udf { <udf_name> <udf_val> <udf_mask> } + } ] } + |{ [ [ fragments ] | [ log ] [ time-range <time_range_name> ] | packet-length { <plen_op> <plen0> | <plen_range><plen1> <plen2> } | { tos { <tos_num> | <tos_str> } } | { precedence { <prec_num> | <prec_str> } } | { ttl<ttl_num> } | { udf { <udf_name> <udf_val> <udf_mask> } + } ] } + } } } } } } [ vlan <vlanid> | ingress_intf{ <intfid> | <intfname> } | vlan_priority <vlanpriorityid> ] + { { [ urg | ack | psh | rst | syn | fin | established |[ log ] [ time-range <time_range_name> ] | packet-length { <plen_op> <plen0> | <plen_range> <plen1><plen2> } | { dscp { <dscp_num> | <dscp_str> } } | { http-method { <opt_num> | <opt_str> } } | {tcp-option-length <tcp_opt_len> } | { tcp-flags-mask <tcp_flags_mask> } | { ttl <ttl_num> } ] } + | { [ urg |ack | psh | rst | syn | fin | established | [ log ] [ time-range <time_range_name> ] | packet-length { <plen_op><plen0> | <plen_range> <plen1> <plen2> } | { tos { <tos_num> | <tos_str> } } | { precedence { <prec_num>| <prec_str> } } | { ttl <ttl_num> } ] } + } [ { udf { <udf_name> <udf_val> <udf_mask> } + } ] [ capturesession <session-id> ] { [ <action> <actionid> ] } + [ log ]
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Permit/denypermitdeny
Configure match based on ethertypeethertype
(Optional) Configure match based on vlanvlan
(Optional) Configure match based on ingress interfaceingress_intf
(Optional) Configure match based on priorityvlan_priority
Configure the ethertype valueethertypeid
(Optional) VLAN numbervlanid
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3174
N Commandsno
Page 3319
(Optional) Interface indexintfid
(Optional) Interface nameintfname
(Optional) Vlan Priorityvlanpriorityid
Protocolproto_tcp
Anysrc_any
Source network addresssrc_addr
Source wildcard bitssrc_wild
Source network prefixsrc_prefix
A single source hostsrc_key_host
Source addresssrc_host
Source address groupsrc_key_addrgrp
Address group namesrc_addrgrp_name
(Optional) Port operatorsrc_port_op
(Optional) Port rangesrc_port_range
(Optional) Port numbersrc_port0
(Optional) TCP portsrc_port0_str
(Optional) Port numbersrc_port1
(Optional) TCP portsrc_port1_str
(Optional) Port numbersrc_port2
(Optional) TCP portsrc_port2_str
(Optional) src port groupsrc_portgroup
(Optional) Port group namesrc_port_group
Anydst_any
Destination network addressdst_addr
Destination wildcard bitsdst_wild
Destination network prefixdst_prefix
A single destination hostdst_key_host
Destination addressdst_host
Destination address groupdst_key_addrgrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3175
N Commandsno
Page 3320
Address group namedst_addrgrp_name
(Optional) Port operatordst_port_op
(Optional) Port rangedst_port_range
(Optional) Port numberdst_port0
(Optional) TCP portdst_port0_str
(Optional) Port numberdst_port1
(Optional) TCP portdst_port1_str
(Optional) Port numberdst_port2
(Optional) TCP portdst_port2_str
(Optional) dst port groupdst_portgroup
(Optional) Port group namedst_port_group
(Optional) Match packets with given dscp valuedscp
(Optional) Differentiated services codepoint valuedscp_num
(Optional) Differentiated services codepoint labeldscp_str
(Optional) Match packets with given TOS valuetos
(Optional) Type of service valuetos_num
(Optional) Type of service labeltos_str
(Optional) Match packets with given precedence valueprecedence
(Optional) Precedence valueprec_num
(Optional) Precedence labelprec_str
(Optional) Check non-initial fragmentsfragments
(Optional) Log matches against this entrylog
(Optional) Specify a time rangetime-range
(Optional) Time range nametime_range_name
(Optional) Match packets based on layer 3 packet lengthpacket-length
(Optional) Packet-length operatorplen_op
(Optional) Packet-length rangeplen_range
(Optional) Packet lengthplen0
(Optional) Lower packet lengthplen1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3176
N Commandsno
Page 3321
(Optional) Higher packet lengthplen2
(Optional) Match Packets with a given TTL valuettl
(Optional)ttl_num
(Optional) Specify TCP Options sizetcp-option-length
(Optional) TCP option length (multiples of 4 bytes)tcp_opt_len
(Optional) Specify TCP Flagstcp-flags-mask
(Optional) TCP flags masktcp_flags_mask
(Optional) Match packets based on http-methodhttp-method
(Optional) http_option valueopt_num
(Optional) http_option_paramopt_str
(Optional) Match packets based on layer 3 packet lengthpacket-length
(Optional) Packet-length operatorplen_op
(Optional) Packet-length rangeplen_range
(Optional) Packet lengthplen0
(Optional) Lower packet lengthplen1
(Optional) Higher packet lengthplen2
(Optional) Match on the URG biturg
(Optional) Match on the ACK bitack
(Optional) Match on the PSH bitpsh
(Optional) Match on the RST bitrst
(Optional) Match on the SYN bitsyn
(Optional) Match on the FIN bitfin
(Optional) Match established connectionsestablished
(Optional) User defined field matchudf
(Optional) UDF nameudf_name
(Optional) UDF value to matchudf_val
(Optional) Mask to apply to UDF valueudf_mask
(Optional) Enable packet capture on this filter for sessioncapture
(Optional) Session ID <1-48> for this sessionsession
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3177
N Commandsno
Page 3322
(Optional) Session ID <1-48> for this sessionsession-id
(Optional) Actionaction
(Optional) redirect: Ethernet1/1,port-channel1 set-erspan-dscp: <1-63>set-erspan-gre-proto: <1-65535>
actionid
Command Mode
• /exec/configure/ipacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3178
N Commandsno
Page 3323
no{ [ <seqno> ] | no } <permitdeny> { { ethertype <ethertypeid> } | { <proto_udp> { { { { <src_any> | {<src_addr> <src_wild> } | <src_prefix> | { src_key_host <src_host> } | { src_key_addrgrp <src_addrgrp_name>} } [ { { <src_port_op> { <src_port0> | <src_port0_str> } } | { <src_port_range> { <src_port1> |<src_port1_str> } { <src_port2> | <src_port2_str> } } | src_portgroup <src_port_group> } ] { <dst_any> | {<dst_addr> <dst_wild> } | <dst_prefix> | { dst_key_host <dst_host> } | { dst_key_addrgrp <dst_addrgrp_name>} } [ { { <dst_port_op> { <dst_port0> | <dst_port0_str> } } | { <dst_port_range> { <dst_port1> |<dst_port1_str> } { <dst_port2> | <dst_port2_str> } } | dst_portgroup <dst_port_group> } ] { { [ [ log ] [time-range <time_range_name> ] | packet-length { <plen_op> <plen0> | <plen_range> <plen1> <plen2> } |{ dscp { <dscp_num> | <dscp_str> } } | { ttl <ttl_num> } ] } + | { [ [ log ] [ time-range <time_range_name>] | packet-length { <plen_op> <plen0> | <plen_range> <plen1> <plen2> } | { tos { <tos_num> | <tos_str> }} | { precedence { <prec_num> | <prec_str> } } | { ttl <ttl_num> } ] } + } [ { udf { <udf_name> <udf_val><udf_mask> } + } ] [ nve vni <vni-id> ] } | { { <src_any> | { <src_addr> <src_wild> } | <src_prefix> | {src_key_host <src_host> } | { src_key_addrgrp <src_addrgrp_name> } } { <dst_any> | { <dst_addr> <dst_wild>} | <dst_prefix> | { dst_key_host <dst_host> } | { dst_key_addrgrp <dst_addrgrp_name> } } { { [ [ fragments] | [ log ] [ time-range <time_range_name> ] | packet-length { <plen_op> <plen0> | <plen_range> <plen1><plen2> } | { dscp { <dscp_num> | <dscp_str> } } | { ttl <ttl_num> } | { udf { <udf_name> <udf_val><udf_mask> } + } ] } + | { [ [ fragments ] | [ log ] [ time-range <time_range_name> ] | packet-length {<plen_op> <plen0> | <plen_range> <plen1> <plen2> } | { tos { <tos_num> | <tos_str> } } | { precedence {<prec_num> | <prec_str> } } | { ttl <ttl_num> } | { udf { <udf_name> <udf_val> <udf_mask> } + } ] } + }} } [ nve vni <vni-id> ] } } } [ vlan <vlanid> | ingress_intf { <intfid> | <intfname> } | vlan_priority<vlanpriorityid> ] + { { [ [ log ] [ time-range <time_range_name> ] | packet-length { <plen_op> <plen0> |<plen_range> <plen1> <plen2> } | { dscp { <dscp_num> | <dscp_str> } } | { ttl <ttl_num> } ] } + | { [ [ log] [ time-range <time_range_name> ] | packet-length { <plen_op> <plen0> | <plen_range> <plen1> <plen2>} | { tos { <tos_num> | <tos_str> } } | { precedence { <prec_num> | <prec_str> } } | { ttl <ttl_num> } ] } + }[ { udf { <udf_name> <udf_val> <udf_mask> } + } ] # 2293 ../feature/acl_mgr/cli/aclmgr.cmd [ capturesession <session-id> ] { [ <action> <actionid> ] } + [ log ]
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Permit/denypermitdeny
Configure match based on ethertypeethertype
(Optional) Configure match based on vlanvlan
(Optional) Configure match based on ingress interfaceingress_intf
(Optional) Configure match based on priorityvlan_priority
Configure the ethertype valueethertypeid
(Optional) VLAN numbervlanid
(Optional) Interface indexintfid
(Optional) Interface nameintfname
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3179
N Commandsno
Page 3324
(Optional) Vlan Priorityvlanpriorityid
Protocolproto_udp
Anysrc_any
Source network addresssrc_addr
Source wildcard bitssrc_wild
Source network prefixsrc_prefix
A single source hostsrc_key_host
Source addresssrc_host
Source address groupsrc_key_addrgrp
Address group namesrc_addrgrp_name
(Optional) Port operatorsrc_port_op
(Optional) Port rangesrc_port_range
(Optional) Port numbersrc_port0
(Optional) UDP portsrc_port0_str
(Optional) Port numbersrc_port1
(Optional) UDP portsrc_port1_str
(Optional) Port numbersrc_port2
(Optional) UDP portsrc_port2_str
(Optional) src port groupsrc_portgroup
(Optional) Port group namesrc_port_group
Anydst_any
Destination network addressdst_addr
Destination wildcard bitsdst_wild
Destination network prefixdst_prefix
A single destination hostdst_key_host
Destination addressdst_host
Destination address groupdst_key_addrgrp
Address group namedst_addrgrp_name
(Optional) Port operatordst_port_op
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3180
N Commandsno
Page 3325
(Optional) Port rangedst_port_range
(Optional) Port numberdst_port0
(Optional) UDP portdst_port0_str
(Optional) Port numberdst_port1
(Optional) UDP portdst_port1_str
(Optional) Port numberdst_port2
(Optional) UDP portdst_port2_str
(Optional) dst port groupdst_portgroup
(Optional) Port group namedst_port_group
(Optional) Match packets with given dscp valuedscp
(Optional) Differentiated services codepoint valuedscp_num
(Optional) Differentiated services codepoint labeldscp_str
(Optional) Match packets with given TOS valuetos
(Optional) Type of service valuetos_num
(Optional) Type of service labeltos_str
(Optional) Match packets with given precedence valueprecedence
(Optional) Precedence valueprec_num
(Optional) Precedence labelprec_str
(Optional) Check non-initial fragmentsfragments
(Optional) Log matches against this entrylog
(Optional) Specify a time rangetime-range
(Optional) Time range nametime_range_name
(Optional) Match packets based on layer 3 packet lengthpacket-length
(Optional) Packet-length operatorplen_op
(Optional) Packet-length rangeplen_range
(Optional) Packet lengthplen0
(Optional) Lower packet lengthplen1
(Optional) Higher packet lengthplen2
(Optional) Match Packets with a given TTL valuettl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3181
N Commandsno
Page 3326
(Optional)ttl_num
(Optional) VNI ID <0-16777215>nve
(Optional) VNI ID <0-16777215>vni
(Optional) VNI ID <0-16777215>vni-id
(Optional) User defined field matchudf
(Optional) UDF nameudf_name
(Optional) UDF value to matchudf_val
(Optional) Mask to apply to UDF valueudf_mask
(Optional) Enable packet capture on this filter for sessioncapture
(Optional) Session ID <1-48> for this sessionsession
(Optional) Session ID <1-48> for this sessionsession-id
(Optional) Actionaction
(Optional) redirect: Ethernet1/1,port-channel1 set-erspan-dscp: <1-63>set-erspan-gre-proto: <1-65535>
actionid
Command Mode
• /exec/configure/ipacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3182
N Commandsno
Page 3327
no{ [ <seqno> ] | no } <permitdeny> <proto_igmp> { { { <src_any> | { <src_addr> <src_wild> } | <src_prefix>| { src_key_host <src_host> } | { src_key_addrgrp <src_addrgrp_name> } } { <dst_any> | { <dst_addr><dst_wild> } | <dst_prefix> | { dst_key_host <dst_host> } | { dst_key_addrgrp <dst_addrgrp_name> } } { [[ log ] [ time-range <time_range_name> ] | <igmp_num> | packet-length { <plen_op> <plen0> | <plen_range><plen1> <plen2> } | { dscp { <dscp_num> | <dscp_str> } } ] + | [ [ log ] [ time-range <time_range_name> ]| <igmp_str> | packet-length { <plen_op> <plen0> | <plen_range> <plen1> <plen2> } | { dscp { <dscp_num>| <dscp_str> } } ] + | [ [ log ] [ time-range <time_range_name> ] | <igmp_num> | packet-length { <plen_op><plen0> | <plen_range> <plen1> <plen2> } | { tos { <tos_num> | <tos_str> } } | { precedence { <prec_num>| <prec_str> } } ] + | [ [ log ] [ time-range <time_range_name> ] | <igmp_str> | packet-length { <plen_op><plen0> | <plen_range> <plen1> <plen2> } | { tos { <tos_num> | <tos_str> } } | { precedence { <prec_num>| <prec_str> } } ] + } } | { { <src_any> | { <src_addr> <src_wild> } | <src_prefix> | { src_key_host <src_host>} | { src_key_addrgrp <src_addrgrp_name> } } { <dst_any> | { <dst_addr> <dst_wild> } | <dst_prefix> | {dst_key_host <dst_host> } | { dst_key_addrgrp <dst_addrgrp_name> } } { { [ [ fragments ] | [ log ] [ time-range<time_range_name> ] | packet-length { <plen_op> <plen0> | <plen_range> <plen1> <plen2> } | { dscp {<dscp_num> | <dscp_str> } } | { ttl <ttl_num> } ] } + | { [ [ fragments ] | [ log ] [ time-range<time_range_name> ] | packet-length { <plen_op> <plen0> | <plen_range> <plen1> <plen2> } | { tos {<tos_num> | <tos_str> } } | { precedence { <prec_num> | <prec_str> } } | { ttl <ttl_num> } ] } + } } [ capturesession <session-id> ] { [ <action> <actionid> ] } + [ log ] }
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Permit/denypermitdeny
Protocolproto_igmp
Anysrc_any
Source network addresssrc_addr
Source wildcard bitssrc_wild
Source network prefixsrc_prefix
A single source hostsrc_key_host
Source addresssrc_host
Source address groupsrc_key_addrgrp
Address group namesrc_addrgrp_name
Anydst_any
Destination network addressdst_addr
Destination wildcard bitsdst_wild
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3183
N Commandsno
Page 3328
Destination network prefixdst_prefix
A single destination hostdst_key_host
Destination addressdst_host
Destination address groupdst_key_addrgrp
Address group namedst_addrgrp_name
(Optional) Match packets with given dscp valuedscp
(Optional) Differentiated services codepoint valuedscp_num
(Optional) Differentiated services codepoint labeldscp_str
(Optional) Match packets with given TOS valuetos
(Optional) Type of service valuetos_num
(Optional) Type of service labeltos_str
(Optional) Match packets with given precedence valueprecedence
(Optional) Precedence valueprec_num
(Optional) Precedence labelprec_str
(Optional) Check non-initial fragmentsfragments
(Optional) Log matches against this entrylog
(Optional) Specify a time rangetime-range
(Optional) Time range nametime_range_name
(Optional) Match packets based on layer 3 packet lengthpacket-length
(Optional) Packet-length operatorplen_op
(Optional) Packet-length rangeplen_range
(Optional) Packet lengthplen0
(Optional) Lower packet lengthplen1
(Optional) Higher packet lengthplen2
(Optional) Match Packets with a given TTL valuettl
(Optional)ttl_num
(Optional) IGMP message typeigmp_num
(Optional) IGMP typeigmp_str
(Optional) Enable packet capture on this filter for sessioncapture
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3184
N Commandsno
Page 3329
(Optional) Session ID <1-48> for this sessionsession
(Optional) Session ID <1-48> for this sessionsession-id
(Optional) Actionaction
(Optional) redirect: Ethernet1/1,port-channel1 set-erspan-dscp: <1-63>set-erspan-gre-proto: <1-65535>
actionid
Command Mode
• /exec/configure/ipacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3185
N Commandsno
Page 3330
no{ [ <seqno> ] | no } <permitdeny> { { { ethertype <ethertypeid> } | { <proto_icmp> { { { <src_any> | {<src_addr> <src_wild> } | <src_prefix> | { src_key_host <src_host> } | { src_key_addrgrp <src_addrgrp_name>} } { <dst_any> | { <dst_addr> <dst_wild> } | <dst_prefix> | { dst_key_host <dst_host> } | { dst_key_addrgrp<dst_addrgrp_name> } } { [ [ log ] [ time-range <time_range_name> ] | { <icmp_type> [ <icmp_code> ] } |packet-length { <plen_op> <plen0> | <plen_range> <plen1> <plen2> } | { dscp { <dscp_num> | <dscp_str>} } ] + | [ [ log ] [ time-range <time_range_name> ] | <icmp_str> | packet-length { <plen_op> <plen0> |<plen_range> <plen1> <plen2> } | { dscp { <dscp_num> | <dscp_str> } } ] + | [ [ log ] [ time-range<time_range_name> ] | { <icmp_type> [ <icmp_code> ] } | packet-length { <plen_op> <plen0> | <plen_range><plen1> <plen2> } | { tos { <tos_num> | <tos_str> } } | { precedence { <prec_num> | <prec_str> } } ] + | [ [log ] [ time-range <time_range_name> ] | <icmp_str> | packet-length { <plen_op> <plen0> | <plen_range><plen1> <plen2> } | { tos { <tos_num> | <tos_str> } } | { precedence { <prec_num> | <prec_str> } } ] + } }| { { <src_any> | { <src_addr> <src_wild> } | <src_prefix> | { src_key_host <src_host> } | { src_key_addrgrp<src_addrgrp_name> } } { <dst_any> | { <dst_addr> <dst_wild> } | <dst_prefix> | { dst_key_host <dst_host>} | { dst_key_addrgrp <dst_addrgrp_name> } } { { [ [ fragments ] | [ log ] [ time-range <time_range_name>] | packet-length { <plen_op> <plen0> | <plen_range> <plen1> <plen2> } | { dscp { <dscp_num> | <dscp_str>} } | { ttl <ttl_num> } ] } + | { [ [ fragments ] | [ log ] [ time-range <time_range_name> ] | packet-length {<plen_op> <plen0> | <plen_range> <plen1> <plen2> } | { tos { <tos_num> | <tos_str> } } | { precedence {<prec_num> | <prec_str> } } | { ttl <ttl_num> } ] } + } } } } } [ vlan <vlanid> | ingress_intf { <intfid> |<intfname> } | vlan_priority <vlanpriorityid> ] + [ capture session <session-id> ] { [ <action> <actionid> ]} + [ log ] }
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Permit/denypermitdeny
Configure match based on ethertypeethertype
(Optional) Configure match based on vlanvlan
(Optional) Configure match based on ingress interfaceingress_intf
(Optional) Configure match based on priorityvlan_priority
Configure the ethertype valueethertypeid
(Optional) VLAN numbervlanid
(Optional) Interface indexintfid
(Optional) Interface nameintfname
(Optional) Vlan Priorityvlanpriorityid
Protocolproto_icmp
Anysrc_any
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3186
N Commandsno
Page 3331
Source network addresssrc_addr
Source wildcard bitssrc_wild
Source network prefixsrc_prefix
A single source hostsrc_key_host
Source addresssrc_host
Source address groupsrc_key_addrgrp
Address group namesrc_addrgrp_name
Anydst_any
Destination network addressdst_addr
Destination wildcard bitsdst_wild
Destination network prefixdst_prefix
A single destination hostdst_key_host
Destination addressdst_host
Destination address groupdst_key_addrgrp
Address group namedst_addrgrp_name
(Optional) Match packets with given dscp valuedscp
(Optional) Differentiated services codepoint valuedscp_num
(Optional) Differentiated services codepoint labeldscp_str
(Optional) Match packets with given TOS valuetos
(Optional) Type of service valuetos_num
(Optional) Type of service labeltos_str
(Optional) Match packets with given precedence valueprecedence
(Optional) Precedence valueprec_num
(Optional) Precedence labelprec_str
(Optional) Check non-initial fragmentsfragments
(Optional) Log matches against this entrylog
(Optional) Specify a time rangetime-range
(Optional) Time range nametime_range_name
(Optional) Match packets based on layer 3 packet lengthpacket-length
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3187
N Commandsno
Page 3332
(Optional) Packet-length operatorplen_op
(Optional) Packet-length rangeplen_range
(Optional) Packet lengthplen0
(Optional) Lower packet lengthplen1
(Optional) Higher packet lengthplen2
(Optional) Match Packets with a given TTL valuettl
(Optional)ttl_num
(Optional) ICMP message typeicmp_type
(Optional) ICMP message codeicmp_code
(Optional) ICMP labelicmp_str
(Optional) Enable packet capture on this filter for sessioncapture
(Optional) Session ID <1-48> for this sessionsession
(Optional) Session ID <1-48> for this sessionsession-id
(Optional) Actionaction
(Optional) redirect: Ethernet1/1,port-channel1 set-erspan-dscp: <1-63>set-erspan-gre-proto: <1-65535>
actionid
Command Mode
• /exec/configure/ipacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3188
N Commandsno
Page 3333
no{ [ <seqno> ] | no } <permitdeny> <proto_tcp> { { { <src_any> | { <src_addr> <src_wild> } | <src_prefix>| { src_key_host <src_host> } | { src_key_addrgrp <src_addrgrp_name> } } [ { { <src_port_op> { <src_port0>| <src_port0_str> } } | { <src_port_range> { <src_port1> | <src_port1_str> } { <src_port2> | <src_port2_str>} } | src_portgroup <src_port_group> } ] { <dst_any> | { <dst_addr> <dst_wild> } | <dst_prefix> | {dst_key_host <dst_host> } | { dst_key_addrgrp <dst_addrgrp_name> } } [ { { <dst_port_op> { <dst_port0>| <dst_port0_str> } } | { <dst_port_range> { <dst_port1> | <dst_port1_str> } { <dst_port2> | <dst_port2_str>} } | dst_portgroup <dst_port_group> } ] { [ { dscp { <dscp_num> | <dscp_str> } } ] | [ { flow-label<flow_num> } ] | [ log ] [ time-range <time_range_name> ] | [ urg | ack | psh | rst | syn | fin | established ] | {tcp-flags-mask <tcp_flags_mask> } | [ packet-length { <plen_op> <plen0> | <plen_range> <plen1> <plen2>} ] } + } | { { <src_any> | { <src_addr> <src_wild> } | <src_prefix> | { src_key_host <src_host> } | {src_key_addrgrp <src_addrgrp_name> } } { <dst_any> | { <dst_addr> <dst_wild> } | <dst_prefix> | {dst_key_host <dst_host> } | { dst_key_addrgrp <dst_addrgrp_name> } } { [ { dscp { <dscp_num> | <dscp_str>} } ] [ { flow-label <flow_num> } ] [ fragments ] [ log ] [ time-range <time_range_name> ] [ packet-length{ <plen_op> <plen0> | <plen_range> <plen1> <plen2> } ] [ { udf { <udf_name> <udf_val> <udf_mask> }+ } ] } + } } [ vlan <vlanid> | ingress_intf { <intfid> | <intfname> } | vlan_priority <vlanpriorityid> ] + [capture session <session-id> ] { [ <actionv6> <actionidv6> ] }
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Permit/denypermitdeny
Protocolproto_tcp
(Optional) Configure match based on vlanvlan
(Optional) Configure match based on ingress interfaceingress_intf
(Optional) Configure match based on priorityvlan_priority
(Optional) User defined field matchudf
(Optional) UDF nameudf_name
(Optional) UDF value to matchudf_val
(Optional) Mask to apply to UDF valueudf_mask
(Optional) VLAN numbervlanid
(Optional) Interface indexintfid
(Optional) Interface nameintfname
(Optional) Vlan Priorityvlanpriorityid
Anysrc_any
A single source hostsrc_key_host
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3189
N Commandsno
Page 3334
Source address groupsrc_key_addrgrp
Address group namesrc_addrgrp_name
(Optional) Port operatorsrc_port_op
(Optional) Port rangesrc_port_range
(Optional) Port numbersrc_port0
(Optional) TCP portsrc_port0_str
(Optional) Port numbersrc_port1
(Optional) TCP portsrc_port1_str
(Optional) Port numbersrc_port2
(Optional) TCP portsrc_port2_str
(Optional) src port groupsrc_portgroup
(Optional) Port group namesrc_port_group
Anydst_any
A single destination hostdst_key_host
Destination address groupdst_key_addrgrp
Address group namedst_addrgrp_name
(Optional) Port operatordst_port_op
(Optional) Port rangedst_port_range
(Optional) Port numberdst_port0
(Optional) TCP portdst_port0_str
(Optional) Port numberdst_port1
(Optional) TCP portdst_port1_str
(Optional) Port numberdst_port2
(Optional) TCP portdst_port2_str
(Optional) dst port groupdst_portgroup
(Optional) Port group namedst_port_group
(Optional) Match packets with given dscp valuedscp
(Optional) Differentiated services codepoint valuedscp_num
(Optional) Differentiated services codepoint labeldscp_str
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3190
N Commandsno
Page 3335
(Optional) Flow labelflow-label
(Optional) Flow label valueflow_num
(Optional) Check non-initial fragmentsfragments
(Optional) Log matches against this entrylog
(Optional) Specify a time rangetime-range
(Optional) Time range nametime_range_name
(Optional) Match packets based on layer 3 packet lengthpacket-length
(Optional) Packet-length operatorplen_op
(Optional) Packet-length rangeplen_range
(Optional) Packet lengthplen0
(Optional) Lower packet lengthplen1
(Optional) Higher packet lengthplen2
Specify TCP Flagstcp-flags-mask
TCP flags masktcp_flags_mask
(Optional) Match on the URG biturg
(Optional) Match on the ACK bitack
(Optional) Match on the PSH bitpsh
(Optional) Match on the RST bitrst
(Optional) Match on the SYN bitsyn
(Optional) Match on the FIN bitfin
(Optional) Match established connectionsestablished
(Optional) Enable packet capture on this filter for sessioncapture
(Optional) Session ID <1-48> for this sessionsession
(Optional) Session ID <1-48> for this sessionsession-id
(Optional) ActionV6actionv6
(Optional) redirect: Ethernet1/1,port-channel1 set-erspan-dscp: <1-63>set-erspan-gre-proto: <1-65535>
actionidv6
Command Mode
• /exec/configure/ipv6acl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3191
N Commandsno
Page 3336
no{ [ <seqno> ] | no } <permitdeny> <proto_udp> { { { <src_any> | { <src_addr> <src_wild> } | <src_prefix>| { src_key_host <src_host> } | { src_key_addrgrp <src_addrgrp_name> } } [ { { <src_port_op> { <src_port0>| <src_port0_str> } } | { <src_port_range> { <src_port1> | <src_port1_str> } { <src_port2> | <src_port2_str>} } | src_portgroup <src_port_group> } ] { <dst_any> | { <dst_addr> <dst_wild> } | <dst_prefix> | {dst_key_host <dst_host> } | { dst_key_addrgrp <dst_addrgrp_name> } } [ { { <dst_port_op> { <dst_port0>| <dst_port0_str> } } | { <dst_port_range> { <dst_port1> | <dst_port1_str> } { <dst_port2> | <dst_port2_str>} } | dst_portgroup <dst_port_group> } ] { [ { dscp { <dscp_num> | <dscp_str> } } ] [ { flow-label <flow_num>} ] [ log ] [ time-range <time_range_name> ] [ packet-length { <plen_op> <plen0> | <plen_range> <plen1><plen2> } ] } + } [ nve vni <vni-id> ] | { { <src_any> | { <src_addr> <src_wild> } | <src_prefix> | {src_key_host <src_host> } | { src_key_addrgrp <src_addrgrp_name> } } { <dst_any> | { <dst_addr> <dst_wild>} | <dst_prefix> | { dst_key_host <dst_host> } | { dst_key_addrgrp <dst_addrgrp_name> } } { [ { dscp {<dscp_num> | <dscp_str> } } ] [ { flow-label <flow_num> } ] [ fragments ] [ log ] [ time-range<time_range_name> ] [ packet-length { <plen_op> <plen0> | <plen_range> <plen1> <plen2> } ] [ { udf {<udf_name> <udf_val> <udf_mask> } + } ] } + } } [ nve vni <vni-id> ] [ vlan <vlanid> | ingress_intf {<intfid> | <intfname> } | vlan_priority <vlanpriorityid> ] + [ capture session <session-id> ] { [ <actionv6><actionidv6> ] }
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Permit/denypermitdeny
Protocolproto_udp
(Optional) Configure match based on vlanvlan
(Optional) Configure match based on ingress interfaceingress_intf
(Optional) Configure match based on priorityvlan_priority
(Optional) User defined field matchudf
(Optional) UDF nameudf_name
(Optional) UDF value to matchudf_val
(Optional) Mask to apply to UDF valueudf_mask
(Optional) VLAN numbervlanid
(Optional) Interface indexintfid
(Optional) Interface nameintfname
(Optional) Vlan Priorityvlanpriorityid
Anysrc_any
A single source hostsrc_key_host
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3192
N Commandsno
Page 3337
Source address groupsrc_key_addrgrp
Address group namesrc_addrgrp_name
(Optional) Port operatorsrc_port_op
(Optional) Port rangesrc_port_range
(Optional) Port numbersrc_port0
(Optional) UDP portsrc_port0_str
(Optional) Port numbersrc_port1
(Optional) UDP portsrc_port1_str
(Optional) Port numbersrc_port2
(Optional) UDP portsrc_port2_str
(Optional) src port groupsrc_portgroup
(Optional) Port group namesrc_port_group
Anydst_any
A single destination hostdst_key_host
Destination address groupdst_key_addrgrp
Address group namedst_addrgrp_name
(Optional) Port operatordst_port_op
(Optional) Port rangedst_port_range
(Optional) Port numberdst_port0
(Optional) UDP portdst_port0_str
(Optional) Port numberdst_port1
(Optional) UDP portdst_port1_str
(Optional) Port numberdst_port2
(Optional) UDP portdst_port2_str
(Optional) dst port groupdst_portgroup
(Optional) Port group namedst_port_group
(Optional) Match packets with given dscp valuedscp
(Optional) Differentiated services codepoint valuedscp_num
(Optional) Differentiated services codepoint labeldscp_str
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3193
N Commandsno
Page 3338
(Optional) Flow labelflow-label
(Optional) Flow label valueflow_num
(Optional) Check non-initial fragmentsfragments
(Optional) Log matches against this entrylog
(Optional) Specify a time rangetime-range
(Optional) Time range nametime_range_name
(Optional) Match packets based on layer 3 packet lengthpacket-length
(Optional) Packet-length operatorplen_op
(Optional) Packet-length rangeplen_range
(Optional) Packet lengthplen0
(Optional) Lower packet lengthplen1
(Optional) Higher packet lengthplen2
(Optional) Enable packet capture on this filter for sessioncapture
(Optional) Session ID <1-48> for this sessionsession
(Optional) Session ID <1-48> for this sessionsession-id
(Optional) VNI ID <0-16777215>nve
(Optional) VNI ID <0-16777215>vni
(Optional) VNI ID <0-16777215>vni-id
(Optional) ActionV6actionv6
(Optional) redirect: Ethernet1/1,port-channel1 set-erspan-dscp: <1-63>set-erspan-gre-proto: <1-65535>
actionidv6
Command Mode
• /exec/configure/ipv6acl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3194
N Commandsno
Page 3339
no{ [ <seqno> ] | no } <permitdeny> <proto_sctp> { { { <src_any> | { <src_addr> <src_wild> } | <src_prefix>| { src_key_host <src_host> } | { src_key_addrgrp <src_addrgrp_name> } } [ { { <src_port_op> { <src_port0>| <src_port0_str> } } | { <src_port_range> { <src_port1> | <src_port1_str> } { <src_port2> | <src_port2_str>} } | src_portgroup <src_port_group> } ] { <dst_any> | { <dst_addr> <dst_wild> } | <dst_prefix> | {dst_key_host <dst_host> } | { dst_key_addrgrp <dst_addrgrp_name> } } [ { { <dst_port_op> { <dst_port0>| <dst_port0_str> } } | { <dst_port_range> { <dst_port1> | <dst_port1_str> } { <dst_port2> | <dst_port2_str>} } | dst_portgroup <dst_port_group> } ] { [ { dscp { <dscp_num> | <dscp_str> } } ] [ { flow-label <flow_num>} ] [ log ] [ time-range <time_range_name> ] [ packet-length { <plen_op> <plen0> | <plen_range> <plen1><plen2> } ] } + } | { { <src_any> | { <src_addr> <src_wild> } | <src_prefix> | { src_key_host <src_host> }| { src_key_addrgrp <src_addrgrp_name> } } { <dst_any> | { <dst_addr> <dst_wild> } | <dst_prefix> | {dst_key_host <dst_host> } | { dst_key_addrgrp <dst_addrgrp_name> } } { [ { dscp { <dscp_num> | <dscp_str>} } ] [ { flow-label <flow_num> } ] [ fragments ] [ log ] [ time-range <time_range_name> ] [ packet-length{ <plen_op> <plen0> | <plen_range> <plen1> <plen2> } ] [ { udf { <udf_name> <udf_val> <udf_mask> }+ } ] } + } [ vlan <vlanid> | ingress_intf { <intfid> | <intfname> } | vlan_priority <vlanpriorityid> ] + [ capturesession <session-id> ] }
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Permit/denypermitdeny
Protocolproto_sctp
(Optional) Configure match based on vlanvlan
(Optional) Configure match based on ingress interfaceingress_intf
(Optional) Configure match based on priorityvlan_priority
(Optional) User defined field matchudf
(Optional) UDF nameudf_name
(Optional) UDF value to matchudf_val
(Optional) Mask to apply to UDF valueudf_mask
(Optional) VLAN numbervlanid
(Optional) Interface indexintfid
(Optional) Interface nameintfname
(Optional) Vlan Priorityvlanpriorityid
Anysrc_any
A single source hostsrc_key_host
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3195
N Commandsno
Page 3340
Source address groupsrc_key_addrgrp
Address group namesrc_addrgrp_name
(Optional) Port operatorsrc_port_op
(Optional) Port rangesrc_port_range
(Optional) Port numbersrc_port0
(Optional) SCTP portsrc_port0_str
(Optional) Port numbersrc_port1
(Optional) SCTP portsrc_port1_str
(Optional) Port numbersrc_port2
(Optional) SCTP portsrc_port2_str
(Optional) src port groupsrc_portgroup
(Optional) Port group namesrc_port_group
Anydst_any
A single destination hostdst_key_host
Destination address groupdst_key_addrgrp
Address group namedst_addrgrp_name
(Optional) Port operatordst_port_op
(Optional) Port rangedst_port_range
(Optional) Port numberdst_port0
(Optional) SCTP portdst_port0_str
(Optional) Port numberdst_port1
(Optional) SCTP portdst_port1_str
(Optional) Port numberdst_port2
(Optional) SCTP portdst_port2_str
(Optional) dst port groupdst_portgroup
(Optional) Port group namedst_port_group
(Optional) Match packets with given dscp valuedscp
(Optional) Differentiated services codepoint valuedscp_num
(Optional) Differentiated services codepoint labeldscp_str
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3196
N Commandsno
Page 3341
(Optional) Flow labelflow-label
(Optional) Flow label valueflow_num
(Optional) Check non-initial fragmentsfragments
(Optional) Log matches against this entrylog
(Optional) Specify a time rangetime-range
(Optional) Time range nametime_range_name
(Optional) Match packets based on layer 3 packet lengthpacket-length
(Optional) Packet-length operatorplen_op
(Optional) Packet-length rangeplen_range
(Optional) Packet lengthplen0
(Optional) Lower packet lengthplen1
(Optional) Higher packet lengthplen2
(Optional) Enable packet capture on this filter for sessioncapture
(Optional) Session ID <1-48> for this sessionsession
(Optional) Session ID <1-48> for this sessionsession-id
Command Mode
• /exec/configure/ipv6acl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3197
N Commandsno
Page 3342
no{ [ <seqno> ] | no } <permitdeny> <proto_icmpv6> { { { { <src_any> | { <src_addr> <src_wild> } |<src_prefix> | { src_key_host <src_host> } | { src_key_addrgrp <src_addrgrp_name> } } { <dst_any> | {<dst_addr> <dst_wild> } | <dst_prefix> | { dst_key_host <dst_host> } | { dst_key_addrgrp <dst_addrgrp_name>} } { [ { <icmpv6_type> [ <icmpv6_code> ] } | { dscp { <dscp_num> | <dscp_str> } } | { flow-label<flow_num> } | [ log ] [ time-range <time_range_name> ] | packet-length { <plen_op> <plen0> | <plen_range><plen1> <plen2> } ] + | [ <icmpv6_str> | { dscp { <dscp_num> | <dscp_str> } } | { flow-label <flow_num>} | [ log ] [ time-range <time_range_name> ] | packet-length { <plen_op> <plen0> | <plen_range> <plen1><plen2> } ] + } } | { { <src_any> | { <src_addr> <src_wild> } | <src_prefix> | { src_key_host <src_host> }| { src_key_addrgrp <src_addrgrp_name> } } { <dst_any> | { <dst_addr> <dst_wild> } | <dst_prefix> | {dst_key_host <dst_host> } | { dst_key_addrgrp <dst_addrgrp_name> } } { [ { dscp { <dscp_num> | <dscp_str>} } ] [ { flow-label <flow_num> } ] [ fragments ] [ log ] [ time-range <time_range_name> ] [ packet-length{ <plen_op> <plen0> | <plen_range> <plen1> <plen2> } ] [ { udf { <udf_name> <udf_val> <udf_mask> }+ } ] } + } } [ vlan <vlanid> | ingress_intf { <intfid> | <intfname> } | vlan_priority <vlanpriorityid> ] + [capture session <session-id> ] { [ <actionv6> <actionidv6> ] } }
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Permit/denypermitdeny
Protocolproto_icmpv6
(Optional) Configure match based on vlanvlan
(Optional) Configure match based on ingress interfaceingress_intf
(Optional) Configure match based on priorityvlan_priority
(Optional) User defined field matchudf
(Optional) UDF nameudf_name
(Optional) UDF value to matchudf_val
(Optional) Mask to apply to UDF valueudf_mask
(Optional) VLAN numbervlanid
(Optional) Interface indexintfid
(Optional) Interface nameintfname
(Optional) Vlan Priorityvlanpriorityid
Anysrc_any
A single source hostsrc_key_host
Source address groupsrc_key_addrgrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3198
N Commandsno
Page 3343
Address group namesrc_addrgrp_name
Anydst_any
A single destination hostdst_key_host
Destination address groupdst_key_addrgrp
Address group namedst_addrgrp_name
(Optional) Match packets with given dscp valuedscp
(Optional) Differentiated services codepoint valuedscp_num
(Optional) Differentiated services codepoint labeldscp_str
(Optional) Flow labelflow-label
(Optional) Flow label valueflow_num
(Optional) Check non-initial fragmentsfragments
(Optional) Log matches against this entrylog
(Optional) Specify a time rangetime-range
(Optional) Time range nametime_range_name
(Optional) Match packets based on layer 3 packet lengthpacket-length
(Optional) Packet-length operatorplen_op
(Optional) Packet-length rangeplen_range
(Optional) Packet lengthplen0
(Optional) Lower packet lengthplen1
(Optional) Higher packet lengthplen2
(Optional) ICMPv6 message typeicmpv6_type
(Optional) ICMPv6 message codeicmpv6_code
(Optional) ICMPv6 labelicmpv6_str
(Optional) Enable packet capture on this filter for sessioncapture
(Optional) Session ID <1-48> for this sessionsession
(Optional) Session ID <1-48> for this sessionsession-id
(Optional) ActionV6actionv6
(Optional) redirect: Ethernet1/1,port-channel1 set-erspan-dscp: <1-63>set-erspan-gre-proto: <1-65535>
actionidv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3199
N Commandsno
Page 3344
Command Mode
• /exec/configure/ipv6acl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3200
N Commandsno
Page 3345
no{ { [ <seqno> ] | no } <permitdeny> { { [ <arp_request> ] req_ip { <sender1_ip_any> | { { <sender1_host><sender1_ip> | { <sender1_net_ip> <sender1_ip_mask> } } } } mac { <sender1_mac_any> | { {<sender1_mac_host> <sender1_mac> | { <sender1_net_mac> <sender1_mac_mask> } } } } } | {<arp_response> resp_ip { <sender2_ip_any> | { { <sender2_host> <sender2_ip> | { <sender2_net_ip><sender2_ip_mask> } } } } { <target_ip_any> | { { <target_host> <target_ip> | { <target_net_ip><target_ip_mask> } } } } mac { <sender2_mac_any> | { { <sender2_mac_host> <sender2_mac> | {<sender2_net_mac> <sender2_mac_mask> } } } } [ { <target_mac_any> | { { <target_mac_host> <target_mac>| { <target_net_mac> <target_mac_mask> } } } } ] } } [ <arp_log> ] [ capture session <session-id> ] }
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Permit/denypermitdeny
Any IP protocolreq_ip
Any IP protocolresp_ip
(Optional) ARP_Requestarp_request
ARP_Responsearp_response
Anysender1_ip_any
Hostsender1_host
IP address <a.b.c.d>sender1_ip
IP address <a.b.c.d>sender1_net_ip
IP mask <a.b.c.d>sender1_ip_mask
Anysender2_ip_any
Hostsender2_host
IP address <a.b.c.d>sender2_ip
IP address <a.b.c.d>sender2_net_ip
IP mask <a.b.c.d>sender2_ip_mask
Anytarget_ip_any
Hosttarget_host
IP address <a.b.c.d>target_ip
IP address <a.b.c.d>target_net_ip
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3201
N Commandsno
Page 3346
IP mask <a.b.c.d>target_ip_mask
MAC configuration commandsmac
Anysender1_mac_any
Hostsender1_mac_host
MAC address EEEE.EEEE.EEEEsender1_mac
MAC address EEEE.EEEE.EEEEsender1_net_mac
MAC mask EEEE.EEEE.EEEEsender1_mac_mask
Anysender2_mac_any
Hostsender2_mac_host
MAC address EEEE.EEEE.EEEEsender2_mac
MAC address EEEE.EEEE.EEEEsender2_net_mac
MAC mask EEEE.EEEE.EEEEsender2_mac_mask
(Optional) Anytarget_mac_any
(Optional) Hosttarget_mac_host
(Optional) MAC address EEEE.EEEE.EEEEtarget_mac
(Optional) MAC address EEEE.EEEE.EEEEtarget_net_mac
(Optional) MAC mask EEEE.EEEE.EEEEtarget_mac_mask
(Optional) Logarp_log
(Optional) Enable packet capture on this filter for sessioncapture
(Optional) Session ID <1-48> for this sessionsession
(Optional) Session ID <1-48> for this sessionsession-id
Command Mode
• /exec/configure/arpacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3202
N Commandsno
Page 3347
no{ [ <seqno> ] | no } { <addr> <wild> | <prefix> | host <hostaddr> }
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Host address of the object-group memberhost
Command Mode
• /exec/configure/ipv6group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3203
N Commandsno
Page 3348
no{ [ <seqno> ] | no } { <_port_op> <port0_num> | <_port_range> <port1_num> <port2_num> }
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Port operator_port_op
Port range_port_range
Port numberport0_num
Port numberport1_num
Port numberport2_num
Command Mode
• /exec/configure/portgroup
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3204
N Commandsno
Page 3349
no{ [ <seqno> ] | no } <permitdeny> { <src_any> | { <src_addr> <src_wild> } } { <dst_any> | { <dst_addr><dst_wild> } } [ <mac_proto> | <mac_proto_str> ] [ vlan <vlan> | cos <cos> ] + [ time-range<time_range_name> ] [ capture session <session-id> ] { [ <macaction> <macactionid> ] } +
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Permit/denypermitdeny
Anysrc_any
Source MAC addresssrc_addr
Source wildcard bitssrc_wild
Anydst_any
Destination MAC addressdst_addr
Destination wildcard bitsdst_wild
(Optional) MAC protocol numbermac_proto
(Optional) MAC protocol namemac_proto_str
(Optional) VLAN numbervlan
(Optional) CoS valuecos
(Optional) VLAN numbervlan
(Optional) CoS valuecos
(Optional) Specify a time rangetime-range
(Optional) Time range nametime_range_name
(Optional) Enable packet capture on this filter for sessioncapture
(Optional) Session ID <1-48> for this sessionsession
(Optional) Session ID <1-48> for this sessionsession-id
(Optional) MAC ACL Actionmacaction
(Optional) redirect: Ethernet1/1,port-channel1macactionid
Command Mode
• /exec/configure/macacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3205
N Commandsno
Page 3350
nono
Syntax Description
Negate a command or set its defaultsno
Command Mode
• /exec/configure/vsan-db
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3206
N Commandsno
Page 3351
node[no] node [ ip <ip-addr> | IPv6 <ip-addrv6> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD nodenode
(Optional) ITD node IPv4 addressip
(Optional) ITD node IP4 prefix in format i.i.i.iip-addr
(Optional) ITD node IPv6 addressIPv6
Command Mode
• /exec/configure/itd-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3207
N Commandsnode
Page 3352
node[no] node [ ip <ip-addr> | IPv6 <ip-addrv6> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Catena device-group nodenode
(Optional) Catena device-group node IPv4 addressip
(Optional) Catena device-group node IP4 prefix in format i.i.i.iip-addr
(Optional) Catena device-group node IPv6 addressIPv6
Command Mode
• /exec/configure/catena-device-grp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3208
N Commandsnode
Page 3353
node[no] node [ ip <ip-addr> | IPv6 <ip-addrv6> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD nodenode
(Optional) ITD node IPv4 addressip
(Optional) ITD node IP4 prefix in format i.i.i.iip-addr
(Optional) ITD node IPv6 addressIPv6
Command Mode
• /exec/configure/itd-session-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3209
N Commandsnode
Page 3354
node ip[no] node { ip <ip-addr> | IPv6 <ip-addrv6> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure nodes for PLB device groupnode
node IPv4 addressip
IP4 prefix in format i.i.i.iip-addr
node IPv6 addressIPv6
Command Mode
• /exec/configure/plb-session-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3210
N Commandsnode ip
Page 3355
node ip[no] node { ip <ip-addr> | IPv6 <ip-addrv6> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure nodes for PLB device groupnode
node IPv4 addressip
IP4 prefix in format i.i.i.iip-addr
node IPv6 addressIPv6
Command Mode
• /exec/configure/plb-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3211
N Commandsnode ip
Page 3356
npiv enable[no] npiv enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/Disable Nx port Id Virtualization (NPIV)enable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3212
N Commandsnpiv enable
Page 3357
npv auto-load-balance disruptive[no] npv auto-load-balance disruptive
Syntax Description
(Optional) Negate a command or set its defaultsno
Config commands for FC N_port Virtualizernpv
configure auto load balancing among preferred external linksauto-load-balance
enable disruptive auto load balancing among external linksdisruptive
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3213
N Commandsnpv auto-load-balance disruptive
Page 3358
npv traffic-map server-interface external-interface[no] npv traffic-map server-interface <if1> external-interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Config commands for FC N_port Virtualizernpv
Configure NPV traffic engineeringtraffic-map
Configure server interface based traffic engineeringserver-interface
if1
Configure preferred external interface(s)external-interface
interface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3214
N Commandsnpv traffic-map server-interface external-interface
Page 3359
nsf await-redist-proto-convergence{ [ no ] nsf await-redist-proto-convergence }
Syntax Description
(Optional) Negate a command or set its defaultsno
Non-stop forwardingnsf
Specify whether EIGRP should wait for other protocols to convergebefore advertising routes
await-redist-proto-convergence
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3215
N Commandsnsf await-redist-proto-convergence
Page 3360
ntp access-group[no] ntp access-group { peer | serve-only | serve | query-only } <acl-name>
Syntax Description
(Optional) Negate a command or set its defaultno
NTP configurationntp
NTP access-groupaccess-group
access-group peerpeer
access-group serveserve
access-group serve-onlyserve-only
access-group query-onlyquery-only
Name of access listacl-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3216
N Commandsntp access-group
Page 3361
ntp access-group match-all[no] ntp access-group match-all
Syntax Description
(Optional) Negate a command or set its defaultno
NTP configurationntp
NTP access-groupaccess-group
Scan ACLs present in all ntp access groupsmatch-all
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3217
N Commandsntp access-group match-all
Page 3362
ntp allow private[no] ntp allow { private | control [ rate-limit <delay> ] }
Syntax Description
(Optional) Negate a command or set its defaultno
NTP configurationntp
Enable/Disable the packetsallow
Enable/Disable Private mode packetsprivate
Enable/Disable Control mode packetscontrol
(Optional) Rate-limit the control packetsrate-limit
(Optional) Rate-limit delay (Default 3)delay
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3218
N Commandsntp allow private
Page 3363
ntp authenticate[no] ntp authenticate
Syntax Description
(Optional) Negate a command or set its defaultno
NTP configurationntp
Enable/Disable authenticationauthenticate
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3219
N Commandsntp authenticate
Page 3364
ntp authentication-key md5[no] ntp authentication-key <number> md5 <md5> [ 0 | 7 ]
Syntax Description
(Optional) Negate a command or set its defaultno
NTP configurationntp
NTP authentication keyauthentication-key
authentication key number (range 1-65535)number
use md5 authentication schememd5
MD5 stringmd5
(Optional) clear text0
(Optional) encrypted7
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3220
N Commandsntp authentication-key md5
Page 3365
ntp drop-aged-packet[no] ntp drop-aged-packet
Syntax Description
(Optional) Negate a command or set its defaultsno
NTP Configurationntp
Enable or disable Riviera Timestamp Check.drop-aged-packet
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3221
N Commandsntp drop-aged-packet
Page 3366
ntp logging[no] ntp logging
Syntax Description
(Optional) Negate a command or set its defaultno
NTP configurationntp
Enable/Disable logging of NTPD Eventslogging
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3222
N Commandsntp logging
Page 3367
ntp master[no] ntp master [ <stratum-no> ]
Syntax Description
(Optional) Negate a command or set its defaultno
NTP configurationntp
Act as NTP master clockmaster
(Optional) Stratum numberstratum-no
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3223
N Commandsntp master
Page 3368
ntp passive[no] ntp passive
Syntax Description
(Optional) Negate a command or set its defaultno
NTP configurationntp
NTP passive commandpassive
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3224
N Commandsntp passive
Page 3369
ntp peer[no] ntp peer <host0> [ prefer | key <keyid> | use-vrf { <vrf-name> | <vrf-known-name> } | minpoll <minpoll>| maxpoll <maxpoll> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
NTP Configurationntp
NTP Peer addresspeer
Hostname/IP address of the NTP Peerhost0
(Optional) Preferred Serverprefer
(Optional) Keyid to be used while communicating to this serverkey
(Optional) Value of keyid 1-65535keyid
(Optional) Display per-VRF informationuse-vrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Minimum interval to poll a peerminpoll
(Optional) Poll interval in secs to a power of 2 [default 4]minpoll
(Optional) Maximum interval to poll a peermaxpoll
(Optional) Poll interval in secs to a power of 2 [default 6]maxpoll
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3225
N Commandsntp peer
Page 3370
ntp rts-update[no] ntp rts-update
Syntax Description
(Optional) Negate a command or set its defaultsno
NTP Configurationntp
Enable or disable RTS update to linecards.rts-update
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3226
N Commandsntp rts-update
Page 3371
ntp server[no] ntp server <host0> [ prefer | key <keyid> | use-vrf { <vrf-name> | <vrf-known-name> } | minpoll <minpoll>| maxpoll <maxpoll> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
NTP Configurationntp
NTP server addressserver
Hostname/IP address of the NTP Serverhost0
(Optional) Preferred Serverprefer
(Optional) Keyid to be used while communicating to this serverkey
(Optional) Value of keyid 1-65535keyid
(Optional) Display per-VRF informationuse-vrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Minimum interval to poll a serverminpoll
(Optional) Poll interval in secs to a power of 2 [default 4]minpoll
(Optional) Maximum interval to poll a servermaxpoll
(Optional) Poll interval in secs to a power of 2 [default 6]maxpoll
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3227
N Commandsntp server
Page 3372
ntp source-interface[no] ntp source-interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultno
NTP configurationntp
Source interface sending NTP packetssource-interface
Source interfaceinterface
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3228
N Commandsntp source-interface
Page 3373
ntp source[no] ntp source <ip-addr>
Syntax Description
(Optional) Negate a command or set its defaultno
NTP Configurationntp
Source of NTP packetssource
IPv4/IPv6 addressip-addr
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3229
N Commandsntp source
Page 3374
ntp sync-retryntp sync-retry
Syntax Description
NTP configurationntp
Retry synchronization with configured serverssync-retry
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3230
N Commandsntp sync-retry
Page 3375
ntp trusted-key[no] ntp trusted-key <number>
Syntax Description
(Optional) Negate a command or set its defaultno
NTP configurationntp
NTP trusted-keytrusted-key
trusted-key numbernumber
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3231
N Commandsntp trusted-key
Page 3376
nv overlay evpn[no] nv overlay evpn
Syntax Description
(Optional) Negate a command or set its defaultsno
Command to enable/disable featuresnv
Command to enable/disable featuresoverlay
Enable/Disable Ethernet VPN (EVPN)evpn
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3232
N Commandsnv overlay evpn
Page 3377
nxapi certificate{ nxapi certificate { { httpskey { keyfile <uri0> | <line> } } | { httpscrt { certfile <uri1> | <line1> } } | { enable} } }
Syntax Description
Configure nxapinxapi
Https certificate configurationcertificate
Https private keyhttpskey
Https certificatehttpscrt
Https key filekeyfile
Https certificate filecertfile
Enable the current certificateenable
File containing https private key for the useruri0
nxapi https private keyline
File containing https certificateuri1
nxapi https certificateline1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3233
N Commandsnxapi certificate
Page 3378
nxapi flow{ [ no ] nxapi flow }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure nxapinxapi
allow frontend to access /sys/flow/flow
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3234
N Commandsnxapi flow
Page 3379
nxapi http port{ nxapi { http | https } port <s0> } | { no nxapi { http | https } } | { no nxapi { http | https } port <s0> }
Syntax Description
Negate a command or set its defaultsno
Configure nxapinxapi
Http configurationhttp
Https configurationhttps
Port numberport
Port number. Please do not use well-known protocol portss0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3235
N Commandsnxapi http port
Page 3380
nxapi ssl ciphers weak{ [ no ] nxapi ssl ciphers weak }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure nxapinxapi
Configure ssl parametersssl
Configure allowed ciphers for sslciphers
Allow weak ciphersweak
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3236
N Commandsnxapi ssl ciphers weak
Page 3381
nxapi ssl protocols{ nxapi ssl protocols <prot_string> } | { no nxapi ssl protocols }
Syntax Description
Negate a command or set its defaultsno
Configure nxapinxapi
Configure ssl parametersssl
Configure allowed ssl protocolsprotocols
String of supported protocols, Ex: TLSv1 TLSv1.1 TLSv1.2prot_string
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3237
N Commandsnxapi ssl protocols
Page 3382
nxapi use-vrf management default{ nxapi use-vrf { management | default | <vrf_name> } } | { no nxapi use-vrf { management | default |<vrf_name> } }
Syntax Description
Negate a command or set its defaultsno
Configure nxapinxapi
vrf to be used for nxapi communicationuse-vrf
management vrfmanagement
default vrfdefault
name of the vrfvrf_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3238
N Commandsnxapi use-vrf management default
Page 3383
nxsdk enable app[no] nxsdk enable app <app-index>
Syntax Description
(Optional) Negate a command or set its defaultsno
NXOS SDKnxsdk
Command to enable/disable nxsdk applicationenable
Enable/disable applicationapp
Application indexapp-index
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3239
N Commandsnxsdk enable app
Page 3384
nxsdk service-name{ [ no ] nxsdk service-name <service-name> }
Syntax Description
NXOS SDKnxsdk
Complete path and name of file to executeservice-name
Service nameservice-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3240
N Commandsnxsdk service-name
Page 3385
O Commands
• oam-channel, on page 3243• object-group ip address, on page 3244• object-group ip port, on page 3245• object-group ipv6 address, on page 3246• object-group udp relay ip address, on page 3247• object-group udp relay ip address, on page 3248• object-track, on page 3249• of-port interface, on page 3250• on-demand color, on page 3251• openflow, on page 3252• operation-packet-priority normal, on page 3253• option exporter-stats timeout, on page 3254• option interface-table timeout, on page 3255• orib event-history, on page 3256• orib orib_api_init, on page 3257• ospfv3 authentication, on page 3258• ospfv3 bfd, on page 3259• ospfv3 cost, on page 3260• ospfv3 dead-interval, on page 3261• ospfv3 event-history, on page 3262• ospfv3 event-history cli, on page 3263• ospfv3 event-history detail, on page 3264• ospfv3 event-history detail, on page 3265• ospfv3 hello-interval, on page 3266• ospfv3 instance, on page 3267• ospfv3 mtu-ignore, on page 3268• ospfv3 network broadcast, on page 3269• ospfv3 network point-to-point, on page 3270• ospfv3 passive-interface, on page 3271• ospfv3 priority, on page 3272• ospfv3 retransmit-interval, on page 3273• ospfv3 shutdown, on page 3274• ospfv3 transmit-delay, on page 3275
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3241
Page 3386
• other-config-flag, on page 3276• overlay-encapsulation, on page 3277• overwrite-vlan, on page 3278• owner, on page 3279
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3242
O Commands
Page 3387
oam-channel{ oam-channel <val> } | { no oam-channel }
Syntax Description
oam-channel usedoam-channel
2 - nvo3 tissaval
Command Mode
• /exec/configure/configngoamprofile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3243
O Commandsoam-channel
Page 3388
object-group ip address[no] object-group ip address <name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure ACL object groupsobject-group
IP Object groupsip
Address object groupaddress
object-group namename
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3244
O Commandsobject-group ip address
Page 3389
object-group ip port[no] object-group ip port <name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure ACL object groupsobject-group
IP Object groupsip
IP port object group (can be used in IPv4 and IPv6 access-lists)port
object-group namename
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3245
O Commandsobject-group ip port
Page 3390
object-group ipv6 address[no] object-group ipv6 address <name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure ACL object groupsobject-group
IPv6 Object groupsipv6
Address object groupaddress
object-group namename
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3246
O Commandsobject-group ipv6 address
Page 3391
object-group udp relay ip address[no] object-group udp relay ip address <obj-grp-name>
Syntax Description
Negate a command or set its defaultsno
Configure object groupsobject-group
Configure UDPudp
Configure UDP Relayrelay
IP Object groupsip
Address object groupaddress
object-group nameobj-grp-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3247
O Commandsobject-group udp relay ip address
Page 3392
object-group udp relay ip addressobject-group udp relay ip address <obj-grp-name>
Syntax Description
Configure object groupsobject-group
Configure UDPudp
Configure UDP Relayrelay
IP Object groupsip
Address object groupaddress
object-group nameobj-grp-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3248
O Commandsobject-group udp relay ip address
Page 3393
object-track[no] object-track <object-number> [ decrement <value> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Associates track object to VRRP groupobject-track
Set the object number to the groupobject-number
(Optional) Decrements vrrp group priority when tracked object goesdown
decrement
(Optional) Set the value to decrement from priorityvalue
Command Mode
• /exec/configure/if-eth-any/vrrpv3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3249
O Commandsobject-track
Page 3394
of-port interface[no] of-port interface <ifname>
Syntax Description
(Optional) Negate a command or set its defaultsno
Add interfaces to openflow switchof-port
Interfaceinterface
interface nameifname
Command Mode
• /exec/configure/openflow/switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3250
O Commandsof-port interface
Page 3395
on-demand color[no] on-demand color <color>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure on-demand coloron-demand
Colorcolor
Colorcolor
Command Mode
• /exec/configure/sr/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3251
O Commandson-demand color
Page 3396
openflow[no] openflow
Syntax Description
(Optional) Negate a command or set its defaultsno
OpenFlow configurationopenflow
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3252
O Commandsopenflow
Page 3397
operation-packet-priority normal{ { no | default } operation-packet-priority | operation-packet-priority { normal | high } }
Syntax Description
no
Set a command to its defaultsdefault
Set operation packet propertiesoperation-packet-priority
Priority highhigh
Priority normalnormal
Command Mode
• /exec/configure/ip-sla/jitter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3253
O Commandsoperation-packet-priority normal
Page 3398
option exporter-stats timeout{ [ no ] option exporter-stats timeout <time> | no option exporter-stats timeout }
Syntax Description
Version 9 Option Templates and Dataoption
Exporter Statistics Optionexporter-stats
Option resend timetimeout
Time in secondstime
Command Mode
• /exec/configure/nfm-exporter-v9
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3254
O Commandsoption exporter-stats timeout
Page 3399
option interface-table timeout{ [ no ] option interface-table timeout <time> | no option interface-table timeout }
Syntax Description
Version 9 Option Templates and Dataoption
Interface Table Optioninterface-table
Option resend timetimeout
Time in secondstime
Command Mode
• /exec/configure/nfm-exporter-v9
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3255
O Commandsoption interface-table timeout
Page 3400
orib event-history[no] orib event-history { cli | ipc | uroute | mroute | mroute_only | uhw | mhw | ha | internal } { size {<size_in_text> | <size_in_kbytes> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Display ORIB informationorib
ORIB event logsevent-history
ORIB cli logscli
ORIB ipc logsipc
ORIB unicast route logsuroute
ORIB multicast route logsmroute
ORIB multicast route logs without mhwmroute_only
ORIB unicast platform logsuhw
ORIB multicast platform logsmhw
ORIB ha logsha
ORIB internal logsinternal
Configure sizesize
Buffer sizesize_in_text
Size in kbytessize_in_kbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3256
O Commandsorib event-history
Page 3401
orib orib_api_init{ orib orib_api_init <client-name> } | { orib orib_api_close } | { orib orib_add_route <client-name> <mac>[ <nh> | <nh6> ] <if-name> } | { orib orib_delete_route <client-name> <mac> [ <nh> | <nh6> ] <if-name> }
Syntax Description
Use ORIB API routines from OTV processorib
Call orib_api_init() from the OTV processorib_api_init
Call orib_api_close() from the OTV processorib_api_close
Call orib_add_route() from OTV processorib_add_route
Call orib_delete_route() from OTV processorib_delete_route
Client name registered to ORIB processclient-name
VLAN-ID/MAC Address tuple in vvvv-aaaa.bbbb.cccc formatmac
(Optional) Next-hop IPv4 addressnh
Next-hop interface (iod)if-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3257
O Commandsorib orib_api_init
Page 3402
ospfv3 authenticationospfv3 authentication { disable | ipsec spi <spi_id> { md5 <akey> | sha1 <akey> } } | no ospfv3 authentication{ disable | ipsec spi <spi_id> }
Syntax Description
Negate a command or set its defaultsno
OSPFv3 configuration commandsospfv3
Enable Authenticationauthentication
Disable Authenticationdisable
IPSecipsec
Security Parameter Indexspi
SPI Valuespi_id
Use the MD5 algorithimmd5
Authentication Keyakey
Use the SHA1 algorithimsha1
Authentication Keyakey
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3258
O Commandsospfv3 authentication
Page 3403
ospfv3 bfd[no] ospfv3 bfd [ disable ]
Syntax Description
(Optional) Negate a command or set its defaultsno
OSPFv3 configuration commandsospfv3
Enable BFD on this interfacebfd
(Optional) Disable BFD on this interfacedisable
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3259
O Commandsospfv3 bfd
Page 3404
ospfv3 cost{ ospfv3 cost <cost> } | { no ospfv3 cost [ <cost> ] }
Syntax Description
Negate a command or set its defaultsno
OSPFv3 configuration commandsospfv3
Cost associated with interfacecost
Cost valuecost
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3260
O Commandsospfv3 cost
Page 3405
ospfv3 dead-interval{ ospfv3 dead-interval <interval> } | { no ospfv3 dead-interval [ <interval> ] }
Syntax Description
Negate a command or set its defaultsno
OSPFv3 configuration commandsospfv3
Dead intervaldead-interval
(seconds)interval
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3261
O Commandsospfv3 dead-interval
Page 3406
ospfv3 event-history[ no ospfv3 event-history { adjacency | event | ha | flooding | lsa | spf | redistribution | hello | spf-trigger } ] |[ ospfv3 event-history { adjacency | event | ha | flooding | lsa | spf | redistribution | hello | spf-trigger } size {<size_in_text> | <size_in_Kbytes> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Debugging functionsospfv3
(Optional) log debug events into event history bufferevent-history
(Optional) Adjacency formation logsadjacency
(Optional) Internal event logsevent
(Optional) HA and GR logsha
(Optional) LSA flooding logsflooding
(Optional) LSA generation and databse logslsa
(Optional) SPF calculation logsspf
(Optional) Redistribution logsredistribution
(Optional) HELLO related logshello
(Optional) SPF TRIGGER related logsspf-trigger
(Optional) Configure the size of the event-hist buffersize
(Optional) Buffer sizesize_in_text
(Optional) Size of the file in kbytessize_in_Kbytes
Command Mode
• /exec/configure/router-ospf3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3262
O Commandsospfv3 event-history
Page 3407
ospfv3 event-history cli[ no ospfv3 event-history cli ] | [ ospfv3 event-history cli size { <size_in_text> | <size_in_Kbytes> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Debugging functionsospfv3
(Optional) log debug events into event history bufferevent-history
(Optional) Cli logscli
(Optional) Configure the size of the event-hist buffersize
(Optional) Buffer sizesize_in_text
(Optional) Size of the file in kbytessize_in_Kbytes
Command Mode
• /exec/configure/router-ospf3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3263
O Commandsospfv3 event-history cli
Page 3408
ospfv3 event-history detail[no] ospfv3 event-history detail
Syntax Description
Negate a command or set its defaultsno
Debugging functionsospfv3
log debug events into event history bufferevent-history
Detailed event history bufferdetail
Command Mode
• /exec/configure/router-ospf3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3264
O Commandsospfv3 event-history detail
Page 3409
ospfv3 event-history detail[ no ospfv3 event-history detail ] | [ ospfv3 event-history detail size { <size_in_text> | <size_in_Kbytes> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Debugging functionsospfv3
(Optional) log debug events into event history bufferevent-history
(Optional) Detailed event history bufferdetail
(Optional) Configure the size of the event-hist buffersize
(Optional) Buffer sizesize_in_text
(Optional) Size of the file in kbytessize_in_Kbytes
Command Mode
• /exec/configure/router-ospf3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3265
O Commandsospfv3 event-history detail
Page 3410
ospfv3 hello-interval{ ospfv3 hello-interval <interval> } | { no ospfv3 hello-interval [ <interval> ] }
Syntax Description
Negate a command or set its defaultsno
OSPFv3 configuration commandsospfv3
Hello intervalhello-interval
(seconds)interval
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3266
O Commandsospfv3 hello-interval
Page 3411
ospfv3 instance{ ospfv3 instance <instance-id> } | { no ospfv3 instance [ <instance-id> ] }
Syntax Description
Negate a command or set its defaultsno
OSPFv3 configuration commandsospfv3
Instance identifierinstance
Instance identifier valueinstance-id
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3267
O Commandsospfv3 instance
Page 3412
ospfv3 mtu-ignore[no] ospfv3 mtu-ignore
Syntax Description
(Optional) Negate a command or set its defaultsno
OSPFv3 configuration commandsospfv3
Disable OSPF MTU mismatch detectionmtu-ignore
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3268
O Commandsospfv3 mtu-ignore
Page 3413
ospfv3 network broadcast{ ospfv3 network { broadcast | point-to-point } } | { no ospfv3 network [ { broadcast | point-to-point } ] }
Syntax Description
Negate a command or set its defaultsno
OSPFv3 configuration commandsospfv3
Network typenetwork
Specify OSPF broadcast multi-access networkbroadcast
Specify OSPF point-to-point networkpoint-to-point
Command Mode
• /exec/configure/if-broadcast /exec/configure/if-p2p /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3269
O Commandsospfv3 network broadcast
Page 3414
ospfv3 network point-to-point{ ospfv3 network point-to-point } | { no ospfv3 network [ point-to-point ] }
Syntax Description
Negate a command or set its defaultsno
OSPFv3 configuration commandsospfv3
Network typenetwork
Specify OSPF point-to-point networkpoint-to-point
Command Mode
• /exec/configure/if-loopback
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3270
O Commandsospfv3 network point-to-point
Page 3415
ospfv3 passive-interface[ default | no ] ospfv3 passive-interface
Syntax Description
(Optional) Undo a commanddefault
(Optional) Negate a command or set its defaultsno
OSPFv3 configuration commandsospfv3
Suppress routing updates on the interfacepassive-interface
Command Mode
• /exec/configure/if-broadcast /exec/configure/if-p2p /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3271
O Commandsospfv3 passive-interface
Page 3416
ospfv3 priority{ ospfv3 priority <prio> } | { no ospfv3 priority [ <prio> ] }
Syntax Description
Negate a command or set its defaultsno
OSPFv3 configuration commandsospfv3
Router prioritypriority
Router priorityprio
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3272
O Commandsospfv3 priority
Page 3417
ospfv3 retransmit-interval{ ospfv3 retransmit-interval <interval> } | { no ospfv3 retransmit-interval [ <interval> ] }
Syntax Description
Negate a command or set its defaultsno
OSPFv3 configuration commandsospfv3
Packet retransmission intervalretransmit-interval
(seconds)interval
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3273
O Commandsospfv3 retransmit-interval
Page 3418
ospfv3 shutdown[no] ospfv3 shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
OSPFv3 configuration commandsospfv3
Shutdown ospf on this interfaceshutdown
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3274
O Commandsospfv3 shutdown
Page 3419
ospfv3 transmit-delay{ ospfv3 transmit-delay <delay> } | { no ospfv3 transmit-delay [ <delay> ] }
Syntax Description
Negate a command or set its defaultsno
OSPFv3 configuration commandsospfv3
Packet transmission delaytransmit-delay
(seconds)delay
Command Mode
• /exec/configure/if-igp /exec/configure/if-gre-tunnel /exec/configure/if-mpls-tunnel/exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3275
O Commandsospfv3 transmit-delay
Page 3420
other-config-flag[no] other-config-flag <state>
Syntax Description
(Optional) Negate a command or set its defaultsno
state
Command Mode
• /exec/configure/config-ra-guard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3276
O Commandsother-config-flag
Page 3421
overlay-encapsulationoverlay-encapsulation <encap-type> [ tunnel-control-frames [ <layer2-prot> ] ] | no overlay-encapsulation
Syntax Description
Negate a command or set its defaultsno
NVE Overlay Encapsulationoverlay-encapsulation
Configure encapsulation typeencap-type
(Optional) tunnel protocoltunnel-control-frames
(Optional) configure specific protocollayer2-prot
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3277
O Commandsoverlay-encapsulation
Page 3422
overwrite-vlan[no] overwrite-vlan <ow-vlan-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Overwrite the system generated vlanoverwrite-vlan
ow-vlan-id
Command Mode
• /exec/configure/static-host/vni
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3278
O Commandsoverwrite-vlan
Page 3423
owner{ { no | default } owner | owner <text> }
Syntax Description
no
Set a command to its defaultsdefault
Owner of Entryowner
Owner Stringtext
Command Mode
• /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/tcp/exec/configure/ip-sla/icmpEcho /exec/configure/ip-sla/dns /exec/configure/ip-sla/fabricPathEcho/exec/configure/ip-sla/http
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3279
O Commandsowner
Page 3424
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3280
O Commandsowner
Page 3425
P Commands
• packet-size, on page 3288• param-list param-list, on page 3289• parity, on page 3290• parity, on page 3291• passive-interface default, on page 3292• passive-interface default, on page 3293• passive-interface default, on page 3294• passive-interface default, on page 3295• password, on page 3296• password, on page 3297• password, on page 3298• password prompt username, on page 3299• password secure-mode, on page 3300• password strength-check, on page 3301• path-option dynamic explicit identifier, on page 3302• path-selection metric igp, on page 3303• path-selection metric igp, on page 3304• path-selection overload allow, on page 3305• path, on page 3306• path next-hop out-label-stack, on page 3307• pause, on page 3308• pause, on page 3309• pause buffer-size2 pause-threshold2 resume-threshold2, on page 3310• pause priority, on page 3311• payload, on page 3312• payload test pattern-type pad, on page 3313• pcc, on page 3314• pce-address ipv4, on page 3315• peer-gateway, on page 3316• peer-ip, on page 3317• peer-keepalive destination, on page 3318• peer-switch, on page 3320• peer-type fabric, on page 3321
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3281
Page 3426
• peer-vtep, on page 3322• peer ip, on page 3323• peer ip, on page 3324• peer local service, on page 3325• peer local service, on page 3326• peer vpc, on page 3327• per-ingress-port-mtu-mode, on page 3328• perf, on page 3329• periodic-inventory notification, on page 3330• periodic-inventory notification interval, on page 3331• periodic to, on page 3332• periodic to, on page 3333• permit interface, on page 3334• permit vlan, on page 3335• permit vrf, on page 3336• permit vsan, on page 3337• personality, on page 3338• personality backup, on page 3339• personality restore, on page 3340• phone-contact, on page 3341• pim, on page 3342• ping, on page 3343• ping6, on page 3345• platform access-list capture, on page 3346• platform access-list fp_dnl, on page 3347• platform access-list update, on page 3348• platform acl tap-agg, on page 3349• platform forwarding interface statistics mode mpls, on page 3350• platform forwarding layer-2 f1 exclude supervisor, on page 3351• platform ip verify, on page 3352• platform ipv6 verify, on page 3354• platform qos, on page 3355• platform qos, on page 3356• platform qos, on page 3357• platform qos, on page 3358• platform qos, on page 3359• platform qos, on page 3360• platform qos, on page 3361• platform qos, on page 3362• platform qos, on page 3364• platform qos, on page 3365• platform qos, on page 3366• platform qos, on page 3367• platform qos, on page 3368• platform qos, on page 3369• platform qos, on page 3370
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3282
P Commands
Page 3427
• platform qos buffer peak monitor counter0 class, on page 3371• platform qos buffer peak monitor counter1 class, on page 3372• platform qos classify ns-only, on page 3373• platform qos eoq, on page 3374• platform qos include ipg, on page 3375• platform qos ing, on page 3376• platform qos ing, on page 3377• platform qos mac ipg, on page 3378• platform qos nodrop-PG-thresholds-FX PG-size, on page 3379• platform qos nodrop-PG-thresholds PG-size, on page 3380• platform qos nodrop-PG-thresholds PG-size Red-threshold Yellow-threshold Green-threshold, on page3381
• platform qos nodrop-queue-thresholds-FX Queue-green, on page 3382• platform qos nodrop-queue-thresholds-roc Queue-green, on page 3383• platform qos ns, on page 3384• platform qos q-noise percent, on page 3385• platform rate-limiter, on page 3386• platform rate-limiter, on page 3388• platform rate-limiter access-list-log, on page 3390• platform rate-limiter span-egress, on page 3391• plb, on page 3392• plb analytics, on page 3393• plb device-group, on page 3394• police, on page 3395• police, on page 3399• police, on page 3401• police, on page 3403• police police pps, on page 3407• police police pps, on page 3409• policy-map, on page 3411• policy-map type control-plane, on page 3412• policy-map type network-qos, on page 3413• policy-map type queuing, on page 3414• policy, on page 3415• policy, on page 3416• policy, on page 3417• pop, on page 3418• port-channel bfd destination, on page 3419• port-channel bfd start, on page 3420• port-channel bfd track-member-link, on page 3421• port-channel fast-convergence, on page 3422• port-channel hash-distribution, on page 3423• port-channel limit, on page 3424• port-channel load-balance, on page 3425• port-channel load-balance1 ethernet, on page 3426• port-channel load-balance2 resilient, on page 3427
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3283
P Commands
Page 3428
• port-channel load-balance ethernet, on page 3428• port-channel load-defer, on page 3429• port-channel port hash-distribution, on page 3430• port-channel port load-defer, on page 3431• port-channel scale-fanout, on page 3432• port-group, on page 3433• port-group, on page 3434• port-license, on page 3435• port-license, on page 3436• port-profile, on page 3437• port-type, on page 3438• port, on page 3439• port, on page 3440• port control, on page 3441• port control, on page 3442• port destination, on page 3443• port type ethernet, on page 3444• postcard-telemetry exporter, on page 3445• postcard-telemetry flow-profile, on page 3446• postcard-telemetry monitor, on page 3447• postcard-telemetry queue-profile, on page 3448• postcard-telemetry system monitor, on page 3449• postcard-telemetry watchlist ip, on page 3450• power efficient-ethernet auto, on page 3451• power efficient-ethernet sleep threshold aggressive, on page 3452• power inline, on page 3453• power inline default_consumption, on page 3454• power inline police action, on page 3455• power inline port priority, on page 3456• power redundancy-mode combined, on page 3457• power redundancy-mode combined force, on page 3458• power redundancy-mode insrc-redundant, on page 3459• power redundancy-mode ps-redundant, on page 3460• power reserve, on page 3461• poweroff, on page 3462• pps, on page 3463• pps, on page 3464• precision milliseconds, on page 3465• preempt, on page 3466• preempt, on page 3467• preempt delay minimum, on page 3468• preempt delay minimum reload sync preempt delay reload minimum sync preempt delay sync minimumreload preempt delay reload syncminimum preempt delay sync reloadminimum preempt delayminimumsync reload preempt delay reload sync preempt delay sync reload preempt delay minimum sync preemptdelay sync minimum preempt delay minimum reload preempt delay reload minimum preempt delayminimum preempt delay reload preempt delay sync preempt, on page 3469
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3284
P Commands
Page 3429
• preference, on page 3471• preference max, on page 3472• preference min, on page 3473• prefix out, on page 3474• priority-flow-control auto-restore multiplier, on page 3475• priority-flow-control fixed-restore multiplier, on page 3476• priority-flow-control inn-recover interface, on page 3477• priority-flow-control mode, on page 3478• priority-flow-control override-interface mode off, on page 3479• priority-flow-control recover interface, on page 3480• priority-flow-control tah-recover interface, on page 3481• priority-flow-control watch-dog-interval on, on page 3482• priority-flow-control watch-dog-interval on, on page 3483• priority-flow-control watch-dog forced on, on page 3484• priority-flow-control watch-dog interval, on page 3485• priority-flow-control watch-dog shutdown-multiplier, on page 3486• priority, on page 3487• priority2, on page 3488• priority, on page 3489• priority, on page 3490• priority, on page 3491• priority, on page 3492• priority, on page 3493• priority, on page 3494• private-vlan, on page 3495• private-vlan association, on page 3496• private-vlan mapping, on page 3497• private-vlan synchronize, on page 3498• probe-interval, on page 3499• probe-interval, on page 3500• probe, on page 3501• probe, on page 3502• probe, on page 3503• probe, on page 3504• probe, on page 3505• probe, on page 3506• probe, on page 3507• probe get, on page 3508• probe get, on page 3509• probe get, on page 3510• probe get, on page 3511• probe host, on page 3512• probe host, on page 3513• probe host, on page 3514• probe host, on page 3515• probe host, on page 3516
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3285
P Commands
Page 3430
• probe host, on page 3517• probe host, on page 3518• probe port, on page 3519• probe port, on page 3520• probe port, on page 3521• probe port, on page 3522• probe port, on page 3523• probe port, on page 3524• probe port, on page 3525• profile, on page 3526• profile, on page 3527• promiscuous-mode off, on page 3528• propagate-sgt, on page 3529• protection, on page 3530• proto, on page 3531• protocol-version, on page 3532• protocol-version, on page 3533• protocol, on page 3534• protocol, on page 3535• protocol shutdown, on page 3536• protocol shutdown, on page 3537• ptp, on page 3538• ptp announce interval, on page 3539• ptp announce timeout, on page 3540• ptp clock-identity, on page 3541• ptp clock-sync auto, on page 3542• ptp clock one-step, on page 3543• ptp convergence-time, on page 3544• ptp correction-range, on page 3545• ptp correction-range logging, on page 3546• ptp correction hardware, on page 3547• ptp cost, on page 3548• ptp delay-request minimum interval, on page 3549• ptp device-type boundary, on page 3550• ptp domain, on page 3551• ptp domain, on page 3552• ptp domain clock-accuracy-threshold, on page 3553• ptp domain clock-class-threshold, on page 3554• ptp domain priority, on page 3555• ptp grandmaster-capable, on page 3556• ptp mean-path-delay, on page 3557• ptp multi-domain, on page 3558• ptp multi-domain transition-attributes priority1, on page 3559• ptp multi-domain transition-attributes priority2, on page 3560• ptp multicast master-only, on page 3561• ptp neighbor propagation-delay-threshold, on page 3562
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3286
P Commands
Page 3431
• ptp offload, on page 3563• ptp pdelay-req-interval, on page 3564• ptp priority1, on page 3565• ptp priority2, on page 3566• ptp source, on page 3567• ptp sync interval, on page 3568• ptp transport ipv4 ucast master, on page 3569• ptp transport ipv4 ucast slave, on page 3570• ptp ucast-source, on page 3571• ptp vlan, on page 3572• purge module running-config, on page 3573• push, on page 3574• pwd, on page 3575• python, on page 3576• python instance, on page 3577
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3287
P Commands
Page 3432
packet-size{ packet-size <packetsize> }
Syntax Description
Packetpacket-size
Sizepacketsize
Command Mode
• /exec/configure/configngoamconnectcheck
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3288
P Commandspacket-size
Page 3433
param-list param-list[no] param-list <plistname> [ cross-check ] | param-list <plistname>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a parameter listparam-list
Enter the name of the parameter listplistname
(Optional) Explicitly search for referencing config profilecross-check
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3289
P Commandsparam-list param-list
Page 3434
parity[no] parity <parity-value>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal parityparity
terminal parity valueparity-value
Command Mode
• /exec/configure/console
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3290
P Commandsparity
Page 3435
parity[no] parity { even | none | odd }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal parityparity
Even parityeven
No paritynone
Odd parityodd
Command Mode
• /exec/configure/com1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3291
P Commandsparity
Page 3436
passive-interface default[no] passive-interface default
Syntax Description
(Optional) Negate a command or set its defaultsno
Suppress routing updates on the interfacepassive-interface
interfaces passive by defaultdefault
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3292
P Commandspassive-interface default
Page 3437
passive-interface default[no] passive-interface default <level>
Syntax Description
(Optional) Negate a command or set its defaultsno
Suppress IS-IS PDUpassive-interface
Undo a commanddefault
IS-IS levellevel
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3293
P Commandspassive-interface default
Page 3438
passive-interface default[no] passive-interface default
Syntax Description
(Optional) Negate a command or set its defaultsno
Suppress routing updates on the interfacepassive-interface
interfaces passive by defaultdefault
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3294
P Commandspassive-interface default
Page 3439
passive-interface default[no] passive-interface default
Syntax Description
(Optional) Negate a command or set its defaultsno
Suppress routing updates on the interfacepassive-interface
interfaces passive by defaultdefault
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3295
P Commandspassive-interface default
Page 3440
passwordpassword <password-string> | { no | default } password [ <password-string> ]
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Configure a password for neighborpassword
Neighbor passwordpassword-string
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-neighbor-stmp/exec/configure/router-bgp/router-bgp-vrf-neighbor/exec/configure/router-bgp/router-bgp-template-neighbor/exec/configure/router-bgp/router-bgp-prefixneighbor/exec/configure/router-bgp/router-bgp-vrf-prefixneighbor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3296
P Commandspassword
Page 3441
passwordpassword [ vrf { <vrf-name> | <vrf-known-name> } ] { required [ req-for <req-pfx-list> ] | { fallback | option<seq-num> opt-for <opt-pfx-list> } { key-chain <name> } } | no password [ vrf { <vrf-name> |<vrf-known-name> } ] { required | fallback | option <seq-num> }
Syntax Description
Negate a command or set its defaultsno
Configure LDP passwordpassword
(Optional) VRF Routing/Forwarding instance informationvrf
(Optional) VPN Routing/Forwarding instance namevrf-name
(Optional) Known VRF namevrf-known-name
Password is required for the peerrequired
(Optional) Prefix list specifying control on LDP peersreq-for
(Optional) Prefix list for LDP peersreq-pfx-list
Specifies a fallback password will followfallback
LDP password optionoption
Sequence number of the LDP password optionseq-num
Prefix list specifying control on LDP peersopt-for
Prefix list for LDP peersopt-pfx-list
Specifies a key-chain name will followkey-chain
Key-chain namename
Command Mode
• /exec/configure/ldp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3297
P Commandspassword
Page 3442
password{ [ no ] password <passwd> }
Syntax Description
passwordpassword
passwordpasswd
Command Mode
• /exec/configure/dot1x-cred
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3298
P Commandspassword
Page 3443
password prompt username[no] password prompt username
Syntax Description
(Optional) Negate a command or set its defaultsno
Password for the userpassword
Enable prompt for passwordprompt
Enable prompt for password on username commandusername
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3299
P Commandspassword prompt username
Page 3444
password secure-mode[no] password secure-mode
Syntax Description
(Optional) Negate a command or set its defaultsno
Password for the userpassword
Enable secure mode for changing passwordsecure-mode
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3300
P Commandspassword secure-mode
Page 3445
password strength-check[no] password strength-check
Syntax Description
(Optional) Negate a command or set its defaultsno
Password for the userpassword
Strength check of passwordstrength-check
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3301
P Commandspassword strength-check
Page 3446
path-option dynamic explicit identifier[no] path-option [ protect ] <pref> | path-option <pref> dynamic [ attributes <attr-name> | { bandwidth <kbps>| lockdown } + ] | path-option [ protect ] <pref> explicit { identifier <id-num> | name <name> } [ { attributes<attr-name> [ verbatim ] | { bandwidth <kbps> | lockdown | verbatim } + } ]
Syntax Description
Negate a command or set its defaultsno
a primary or fallback path setup optionpath-option
(Optional) a path protection setup optionprotect
preference for this path optionpref
setup based on dynamically calculated pathdynamic
setup based on preconfigured pathexplicit
Specify an IP explicit path by numberidentifier
Number of ip explicit pathid-num
Specify an IP explicit path by namename
Name of ip explicit pathname
(Optional) Specify an LSP attribute listattributes
(Optional) Name of LSP attribute listattr-name
(Optional) send out path as is, with no checkingverbatim
(Optional) override the bandwidth configured on the tunnelbandwidth
(Optional) bandwidth requirement in kbpskbps
(Optional) not a candidate for reoptimizationlockdown
(Optional) bandwidth requirement in kbpskbps
(Optional) not a candidate for reoptimizationlockdown
Command Mode
• /exec/configure/if-te /exec/configure/tunnel-te/cbts-member
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3302
P Commandspath-option dynamic explicit identifier
Page 3447
path-selection metric igp[no] path-selection metric | path-selection metric { igp | te }
Syntax Description
Negate a command or set its defaultsno
Path Selection Configurationpath-selection
Metric type for path calculationmetric
Use IGP Metricigp
Use TE Metricte
Command Mode
• /exec/configure/if-te /exec/configure/tunnel-te/cbts-member
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3303
P Commandspath-selection metric igp
Page 3448
path-selection metric igppath-selection metric { igp | te } | no path-selection metric
Syntax Description
Negate a command or set its defaultsno
Path Selection Configurationpath-selection
Metric Type Configurationmetric
Use IGP metricigp
Use TE metric (*Default)te
Command Mode
• /exec/configure/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3304
P Commandspath-selection metric igp
Page 3449
path-selection overload allow[no] path-selection overload allow | path-selection overload allow { head [ middle ] [ tail ] | middle [ tail ] |tail }
Syntax Description
Negate a command or set its defaultsno
Path Selection Configurationpath-selection
Overload Node Configurationoverload
Allow overloaded nodes in CSPFsallow
Allow overloaded head node in TE CSPFhead
(Optional) Allow overloaded middle node in TE CSPFmiddle
(Optional) Allow overloaded tail node in TE CSPFtail
Command Mode
• /exec/configure/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3305
P Commandspath-selection overload allow
Page 3450
pathpath <dn> [ depth { <level> | unbounded } ] [ query-condition <query> ] [ filter-condition <filter> ] | no path<dn>
Syntax Description
Negate a command or set its defaultsno
Create a sensor pathpath
(Optional) Specify a retrieval depthdepth
(Optional) Specify a query conditionquery-condition
(Optional) Specify a filter conditionfilter-condition
Distinguished Namedn
(Optional) Retrieve entire treeunbounded
(Optional) Retrieval depthlevel
(Optional) query conditionquery
(Optional) Filter Conditionfilter
Command Mode
• /exec/configure/telemetry/sensor-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3306
P Commandspath
Page 3451
path next-hop out-label-stack{ no path <path-num> | path <path-num> next-hop <next-hop> out-label-stack { <static-outlabel> + |implicit-null } }
Syntax Description
Negate a command or set its defaultsno
Configure an outgoing path for the LSPpath
Path identifierpath-num
Nexthopnext-hop
Destination IPv4 next hopnext-hop
Series of output labelsout-label-stack
Label Valuestatic-outlabel
IETF MPLS implicit null label (3)implicit-null
Command Mode
• /exec/configure/mpls_static/ipv4/lsp/inlabel/forw
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3307
P Commandspath next-hop out-label-stack
Page 3452
pause[no] pause { no-drop | receive1 | { delayed-drop <timeout> } | { [ buffer-size <size-in-bytes> pause-threshold<xoff-bytes> resume-threshold <xon-bytes> ] pfc-cos <pfc-cos-list> [ receive ] } }
Syntax Description
(Optional) Negate a command or set its defaultsno
PAUSE charecteristics (CBFC)pause
NO-DROPno-drop
Enable delayed-drop for the CoSdelayed-drop
Timer value for delayed droptimeout
(Optional) Ingress buffer size in bytesbuffer-size
(Optional) Buffer limit for pausing in bytespause-threshold
(Optional) Buffer limit at which to resume in bytesresume-threshold
CoS values to assert PFC onpfc-cos
(Optional) Enable only PFC receive for the list of pfc-cos valuesreceive
Enable only PFC receivereceive1
List of class-of-service valuespfc-cos-list
Command Mode
• /exec/configure/policy-map/type/uf/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3308
P Commandspause
Page 3453
pause[no] pause { buffer-size <size-in-bytes> pause-threshold <xoff-bytes> resume-threshold <xon-bytes> }
Syntax Description
(Optional) Negate a command or set its defaultsno
PAUSE characteristics (CBFC)pause
Ingress buffer size in bytesbuffer-size
Buffer limit for pausing in bytespause-threshold
Buffer limit at which to resume in bytesresume-threshold
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3309
P Commandspause
Page 3454
pause buffer-size2 pause-threshold2 resume-threshold2[no] pause buffer-size2 <size-in-bytes> pause-threshold2 <xoff-bytes> resume-threshold2 <xon-bytes>
Syntax Description
(Optional) Negate a command or set its defaultsno
PAUSE characteristics (CBFC)pause
Ingress buffer size in bytesbuffer-size2
Buffer limit for pausing in bytespause-threshold2
Buffer limit at which to resume in bytesresume-threshold2
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3310
P Commandspause buffer-size2 pause-threshold2 resume-threshold2
Page 3455
pause priority[no] pause { priority-group <priority-group-number> }
Syntax Description
(Optional) Negate a command or set its defaultsno
PAUSE characteristics (CBFC)pause
ingress priority-group to which the traffic is mapped and pause limitsare applied
priority-group
Priority group valuepriority-group-number
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3311
P Commandspause priority
Page 3456
payload[no] payload
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure ngoam connectivity check payloadpayload
Command Mode
• /exec/configure/configngoamconnectcheck
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3312
P Commandspayload
Page 3457
payload test pattern-type pad{ payload { test pattern-type <test-id> | pad <pad-val> } } | { no payload { test pattern-type | pad } }
Syntax Description
Negate a command or set its defaultsno
Configure ngoam payloadpayload
Configure ngoam payload testtest
Configure ngoam payload test patternpattern-type
Configure ngoam payload test pattern idtest-id
Configure ngoam payload test pattern padpad
Configure ngoam payload test pad valuepad-val
Command Mode
• /exec/configure/configngoamprofile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3313
P Commandspayload test pattern-type pad
Page 3458
pcc[no] pcc
Syntax Description
(Optional) Negate a command or set its defaultsno
PCC related configurationpcc
Command Mode
• /exec/configure/sr/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3314
P Commandspcc
Page 3459
pce-address ipv4[no] pce-address ipv4 <ip-address> [ precedence <precedence> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure the address of the PCEpce-address
Configure v4 address of the PCEipv4
(Optional) Precedence of the PCEprecedence
PCE addressip-address
(Optional) Path-option preferenceprecedence
Command Mode
• /exec/configure/sr/te/pcc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3315
P Commandspce-address ipv4
Page 3460
peer-gatewaypeer-gateway [ exclude-vlan <vlan-list> ] | no peer-gateway
Syntax Description
Negate a command or set its defaultsno
Enable L3 forwarding for packets destined to peer's gatewaymac-addresspeer-gateway
(Optional) Specify VLANs to be excluded from peer-gatewayfunctionality
exclude-vlan
(Optional) Specify the list of vlansvlan-list
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3316
P Commandspeer-gateway
Page 3461
peer-ip[no] peer-ip <addr>
Syntax Description
(Optional) Negate a command or set its defaultsno
Static IP Address Configurationpeer-ip
Remote Peer IP Addressaddr
Command Mode
• /exec/configure/if-nve/vni/ingr-rep
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3317
P Commandspeer-ip
Page 3462
peer-keepalive destinationpeer-keepalive destination <dst-ip> [ [ source <src-ip> | udp-port <udp-port-num> | vrf { <vrf-name> |<vrf-known-name> } | { interval <interval-ms> timeout <time-out> } | tos-byte <tos-byte-value> | hold-timeout<hold-time-out> ] + | [ source <src-ip> | udp-port <udp-port-num> | vrf { <vrf-name> | <vrf-known-name>} | { interval <interval-ms> timeout <time-out> } | tos { <tos-value> | min-delay | max-throughput |max-reliability | min-monetary-cost | normal } | hold-timeout <hold-time-out> ] + | [ source <src-ip> | udp-port<udp-port-num> | vrf { <vrf-name> | <vrf-known-name> } | { interval <interval-ms> timeout <time-out> } |precedence { <prec-vlaue> | network | internet | critical | flash-override | flash | immediate | priority | routine} | hold-timeout <hold-time-out> ] + ]
Syntax Description
Keepalive/Hello with peer switchpeer-keepalive
specify destination ip address of peer switchdestination
IPv4 address (A.B.C.D) of destinationdst-ip
(Optional) source interface for hellosource
(Optional) IPv4 address (A.B.C.D) of sourcesrc-ip
(Optional) enter UDP port number used for helloudp-port
(Optional) udp port number for hellosudp-port-num
(Optional) vrf to be used for hello messagesvrf
(Optional) vrf to be used for hellosvrf-name
(Optional) Known VRF namevrf-known-name
(Optional) enter interval in millesecondsinterval
(Optional) Enter interval in millesecondsinterval-ms
(Optional) enter timeout in secondstimeout
(Optional) enter timeout in secondstime-out
(Optional) Precedenceprecedence
(Optional) Precedence valueprec-vlaue
(Optional) network (7)network
(Optional) internet (6)internet
(Optional) critical (5)critical
(Optional) flash-override (4)flash-override
(Optional) flash (3)flash
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3318
P Commandspeer-keepalive destination
Page 3463
(Optional) immediate (2)immediate
(Optional) priority (1)priority
(Optional) routine (0)routine
(Optional) Type of Servicetos
(Optional) Enter 4-bit TOS valuetos-value
(Optional) min-delay (8)min-delay
(Optional) max-throughput (4)max-throughput
(Optional) max-reliability (2)max-reliability
(Optional) min-monetary-cost (1)min-monetary-cost
(Optional) normal (0)normal
(Optional) Type of Service Bytetos-byte
(Optional) Enter 8-bit TOS valuetos-byte-value
(Optional) hold timeout to ignore stale peer alive messageshold-timeout
(Optional) Enter hold-timeout in secondshold-time-out
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3319
P Commandspeer-keepalive destination
Page 3464
peer-switch[no] peer-switch
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable peer switch on vPC pair switchespeer-switch
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3320
P Commandspeer-switch
Page 3465
peer-type fabricpeer-type { fabric-external | fabric-border-leaf } | { no | default } peer-type
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Neighbor facingpeer-type
Fabric externalfabric-external
Fabric Border Leaffabric-border-leaf
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3321
P Commandspeer-type fabric
Page 3466
peer-vtep[no] peer-vtep <addr>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure tunnel End Pointpeer-vtep
Remote VTEP IP Addressaddr
Command Mode
• /exec/configure/if-nve/vni
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3322
P Commandspeer-vtep
Page 3467
peer ip[no] peer ip <ip-addr>
Syntax Description
(Optional) Negate a command or set its defaultsno
PLB peerpeer
PLB peer ipip
NICE node IPv4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/plb-inout
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3323
P Commandspeer ip
Page 3468
peer ip[no] peer ip <ip-addr>
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD peerpeer
ITD peer ipip
NICE node IP prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/itd-inout
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3324
P Commandspeer ip
Page 3469
peer local service[no] peer local service <service-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Peer cli for sandwich mode failure notificationpeer
Peer involved in sandwich modelocal
Peer service involved in sandwich modeservice
Peer service nameservice-name
Command Mode
• /exec/configure/plb
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3325
P Commandspeer local service
Page 3470
peer local service[no] peer local service <service-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Peer cli for sandwich mode failure notificationpeer
Peer involved in sandwich modelocal
Peer service involved in sandwich modeservice
Peer service name stringservice-name
Command Mode
• /exec/configure/itd
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3326
P Commandspeer local service
Page 3471
peer vpc[no] peer <svc-name> vpc <num>
Syntax Description
(Optional) Negate a command or set its defaultsno
smart channel peerpeer
vpcvpc
peer smart channel namesvc-name
VPC number to assign to smart-channelnum
Command Mode
• /exec/configure/smartc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3327
P Commandspeer vpc
Page 3472
per-ingress-port-mtu-mode[no] per-ingress-port-mtu-mode
Syntax Description
(Optional) Negate the commandno
per-ingress-port mtu modeper-ingress-port-mtu-mode
Command Mode
• /exec/configure handle auto 424
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3328
P Commandsper-ingress-port-mtu-mode
Page 3473
perfperf [ { record { context-switch | profile } { system | process <i0> } [ <s1> ] } | { stop { all | <s0> } } | { list} | { create-archive <s2> } | { remove { all | <s3> } } ]
Syntax Description
Run perf tool to collect or process event dataperf
(Optional) Record events to a file for later analysisrecord
(Optional) Stop a perf record.stop
(Optional) List recorded datasetslist
(Optional) Create an archive of dataset for downloadcreate-archive
(Optional) Remove recorded dataset(s)remove
(Optional) Act on all recorded datasetsall
(Optional) Record context-switch eventscontext-switch
(Optional) Record periodic runtime samplesprofile
(Optional) Record events for all processes on all CPUSsystem
(Optional) Record events for a specific process with the given pidprocess
(Optional) pid of process to record eventsi0
(Optional) id of perf record session to stops0
(Optional) id to use for perf record sessions1
(Optional) id of perf dataset to create an archives2
(Optional) id of perf dataset to removes3
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3329
P Commandsperf
Page 3474
periodic-inventory notification[no] periodic-inventory notification
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure periodic software inventory message dispatchperiodic-inventory
Enable periodic software inventory message dispatchnotification
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3330
P Commandsperiodic-inventory notification
Page 3475
periodic-inventory notification intervalperiodic-inventory notification { interval <i0> | timeofday <s0> }
Syntax Description
Configure periodic software inventory message dispatchperiodic-inventory
Enable periodic software inventory message dispatchnotification
Configure the time period for periodic inventoryinterval
Time period in days (default is 7 days)i0
Configure the timeofday for periodic inventory in HH:MM formattimeofday
Time period in HH:MM formats0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3331
P Commandsperiodic-inventory notification interval
Page 3476
periodic to{ [ <seqno> ] | no } periodic { { Monday | Tuesday | Wednesday | Thursday | Friday | Saturday | Sunday } +| daily | weekdays | weekend } <stime> to <etime>
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Periodic time and dateperiodic
MondayMonday
TuesdayTuesday
WednesdayWednesday
ThursdayThursday
FridayFriday
SaturdaySaturday
SundaySunday
Every day of the weekdaily
Monday thru Fridayweekdays
Saturday and Sundayweekend
Starting timestime
Ending day and timeto
Ending timeetime
Command Mode
• /exec/configure/timerange
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3332
P Commandsperiodic to
Page 3477
periodic to{ [ <seqno> ] | no } periodic { Monday | Tuesday | Wednesday | Thursday | Friday | Saturday | Sunday }<stime> to { <eday> } <etime>
Syntax Description
(Optional) Sequence numberseqno
Negate a command or set its defaultsno
Periodic time and dateperiodic
MondayMonday
TuesdayTuesday
WednesdayWednesday
ThursdayThursday
FridayFriday
SaturdaySaturday
SundaySunday
Day of the weekeday
Starting timestime
Ending day and timeto
Ending timeetime
Command Mode
• /exec/configure/timerange
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3333
P Commandsperiodic to
Page 3478
permit interface[no] permit interface <if0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Permit access to interfaces (applicable if interface policy is 'deny')permit
Enter the range of interfaces accessible the roleinterface
Enter the interface rangeif0
Command Mode
• /exec/configure/role/interface
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3334
P Commandspermit interface
Page 3479
permit vlan[no] permit vlan <vlan-mrange>
Syntax Description
(Optional) Negate a command or set its defaultsno
Permit access to vlans (applicable if vlan policy is 'deny')permit
Enter the range of vlans accessible the rolevlan
Enter the vlan rangevlan-mrange
Command Mode
• /exec/configure/role/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3335
P Commandspermit vlan
Page 3480
permit vrf[no] permit vrf <vrf-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Permit access to vrf (applicable if vrf policy is 'deny')permit
Enter the range of vrf accessible the rolevrf
Enter the vrf namevrf-name
Command Mode
• /exec/configure/role/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3336
P Commandspermit vrf
Page 3481
permit vsan[no] permit vsan <vsan-mrange>
Syntax Description
(Optional) Negate a command or set its defaultsno
Permit access to vsans (applicable if vsan policy is 'deny')permit
Enter the range of vsans accessible the rolevsan
Enter the vsan rangevsan-mrange
Command Mode
• /exec/configure/role/vsan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3337
P Commandspermit vsan
Page 3482
personality[no] personality
Syntax Description
(Optional) Negate a modeno
Config Personalitypersonality
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3338
P Commandspersonality
Page 3483
personality backuppersonality backup { <uri_local> | <uri_remote> [ password <password> ] [ vrf <vrf-known-name> ] }
Syntax Description
personalitypersonality
backup personalitybackup
(Optional) The password for personality backupspassword
(Optional) The VRF for personality backupsvrf
Personality backup local destinationuri_local
Personality backup remote destinationuri_remote
(Optional) Password for SCP usernamepassword
(Optional) VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3339
P Commandspersonality backup
Page 3484
personality restorepersonality restore <uri> [ user-name <user> ] [ password <password> ] [ hostname <hostname> ] [ vrf<vrf_name> ]
Syntax Description
Personalitypersonality
Restore the personality filerestore
Personality fileuri
(Optional) The username for downloadsuser-name
(Optional) The usernameuser
(Optional) The password for downloadspassword
(Optional) The passwordpassword
(Optional) The hostname for downloadshostname
(Optional) The hostnamehostname
(Optional) The VRF for downloadsvrf
(Optional) The VRF namevrf_name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3340
P Commandspersonality restore
Page 3485
phone-contact{ phone-contact <s0> | no phone-contact }
Syntax Description
Negate a command or set its defaultsno
Contact person's phone numberphone-contact
Phone number in international format(such as +1-800-123-4567)s0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3341
P Commandsphone-contact
Page 3486
pim[no] pim
Syntax Description
(Optional) Negate a command or set its defaultsno
Policies for a Remote Receiverpim
Command Mode
• /exec/configure/nbm-host-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3342
P Commandspim
Page 3487
pingping [ { { <alpha> | <numeric> [ loopback interface <interface> ] } | { multicast <group> interface <interface>[ loopback ] } } [ [ source-interface <src-intf> | vrf { <vrf-name> | <vrf-known-name> } ] [ count { <count>| unlimited } | packet-size <packetsize> | vrf { <vrf-name> | <vrf-known-name> } | interval <interval> | source{ <alpha> | <numeric1> } | df-bit | timeout <timeout> ] + | [ count { <count> | unlimited } | packet-size<packetsize> | source-interface <src-intf> | interval <interval> | df-bit | timeout <timeout> ] + ] ]
Syntax Description
Testping
(Optional) Numbercount
(Optional) Unlimitedunlimited
(Optional) Numbercount
(Optional) Packetpacket-size
(Optional) Sizepacketsize
(Optional) Select source interfacesource-interface
(Optional) Specify interfacesrc-intf
(Optional) Waitinterval
(Optional) Intervalinterval
(Optional) IP address of remote systemnumeric
(Optional) IPnumeric1
(Optional) Enteralpha
(Optional) Multicastmulticast
(Optional) Multicastgroup
(Optional) Interfaceinterface
(Optional) Interfaceinterface
(Optional) Receiveloopback
(Optional) Sourcesource
(Optional) Enabledf-bit
(Optional) Specifytimeout
(Optional) Timeouttimeout
(Optional) Display per-VRF informationvrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3343
P Commandsping
Page 3488
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3344
P Commandsping
Page 3489
ping6ping6 { { <host> | <hostname> } | { multicast <group> } } [ [ { count { <count> | unlimited } } | { packet-size<packetsize> } | [ source { <host1> | <hostname> } ] | vrf { <vrf-name> | <vrf-known-name> } | timeout<timeout> | { interval <interval> } ] + | [ { count { <count> | unlimited } } | { packet-size <packetsize> } | {source-interface <src-intf> } | timeout <timeout> | { interval <interval> } ] + ]
Syntax Description
Testping6
(Optional) Numbercount
(Optional) Numbercount
(Optional) unlimitedunlimited
(Optional) Packetpacket-size
(Optional) Sizepacketsize
(Optional) Select source interfacesource-interface
(Optional) Specify interfacesrc-intf
(Optional) Waitinterval
(Optional) Intervalinterval
Enterhostname
Multicastmulticast
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Sourcesource
(Optional) Specifytimeout
(Optional) Timeouttimeout
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3345
P Commandsping6
Page 3490
platform access-list capture[no] { platform | hardware } access-list capture
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Access Control Listaccess-list
Configure ACL capturecapture
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3346
P Commandsplatform access-list capture
Page 3491
platform access-list fp_dnl[no] { platform | hardware } access-list fp_dnl
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Access control listaccess-list
Fabric path - do not learn mac from broadcastfp_dnl
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3347
P Commandsplatform access-list fp_dnl
Page 3492
platform access-list update[no] { platform | hardware } access-list update { { atomic [ strict ] } | { default-result permit } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Access Control Listaccess-list
Configure atomic/non-atomic update and default-resultupdate
Enable atomic update of access-list in hardwareatomic
(Optional) Strict check on TCAM size for using mutliple featuresstrict
Default access-list result during non-atomic hardware updatedefault-result
Permit all packets during non-atomic updatepermit
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3348
P Commandsplatform access-list update
Page 3493
platform acl tap-agg[no] { platform | hardware } acl tap-agg
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure acl related configurationacl
Enable tap-aggregation feature on this pltfmtap-agg
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3349
P Commandsplatform acl tap-agg
Page 3494
platform forwarding interface statistics mode mpls[no] { platform | hardware } forwarding interface statistics mode { mpls | default } [ module <module-num>]
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Hardware forwardingforwarding
Interfaceinterface
Statisticsstatistics
Statistics modemode
Mpls modempls
Default modedefault
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule-num
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3350
P Commandsplatform forwarding interface statistics mode mpls
Page 3495
platform forwarding layer-2 f1 exclude supervisor[no] { platform | hardware } forwarding layer-2 f1 exclude supervisor
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Forwarding informationforwarding
L2 only modelayer-2
N7K-F132XP-15 modulef1
Exclude supervisor from getting copies of ARP and multicast packetsexclude
Supervisor modulesupervisor
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3351
P Commandsplatform forwarding layer-2 f1 exclude supervisor
Page 3496
platform ip verify[no] { platform | hardware } ip verify { address { source { broadcast | multicast } | class-e | destination { zero} | identical | reserved } | checksum | protocol | fragment | length { minimum | consistent | maximum {max-frag| udp | max-tcp } } | tcp { tiny-frag } | version | syslog }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
IPip
Enable IPv4 and some IPv6 packet validation checks in hardwareverify
IPv4 Source and destination address validationaddress
Check source addresssource
Source address is 255.255.255.255broadcast
Source address is 224.x.x.xmulticast
Check destination addressdestination
Destination address is 0.0.0.0zero
Class E IDS checkclass-e
Same IP SA and DAidentical
Source address is 127.x.x.xreserved
Verify IPv4 and IPv6 packet checksumchecksum
Verify IP procotolprotocol
Check IPv4 and IPv6 fragment with non-zero offset and DF bit activefragment
Validate IPv4 packet header and payload lengthlength
Minimum IPv4 header lengthminimum
Actual frame size is equal to or more than IPv4 length plus ethernetheader
consistent
Check max fragment offset and payload lengthmaximum
Fragment offset field valuemax-frag
Maximum UDP length has to be less than IPv4 payload lengthudp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3352
P Commandsplatform ip verify
Page 3497
Maximum TCP length has to be less than IPv4 payload lengthmax-tcp
Validate TCP packet headertcp
Check TCP tiny fragmenttiny-frag
Must be 4 for an ethertype of IPv4 (0x0800)version
Syslog Messages logging configuration for IDS check dropssyslog
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3353
P Commandsplatform ip verify
Page 3498
platform ipv6 verify[no] { platform | hardware } ipv6 verify { length { consistent | maximum { max-frag | udp | max-tcp } } | tcp{ tiny-frag } | version }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
IPv6ipv6
Enable IPv6 packet validation checks in hardwareverify
Validate IPv6 packet header and payload lengthlength
Actual frame size is equal to or more than IPv6 length plus ethernetheader
consistent
Check max fragment offset and payload lengthmaximum
Fragment offset field valuemax-frag
Maximum UDP length has to be less than IPv6 payload lengthudp
Maximum TCP length has to be less than IPv6 payload lengthmax-tcp
Validate TCP packet headertcp
Check TCP tiny fragmenttiny-frag
Must be 6 for an ethertype of IPv6 (0x86DD)version
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3354
P Commandsplatform ipv6 verify
Page 3499
platform qos[no] { platform | hardware } qos { burst-detect max-records <val> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Set OOBST burst monitor configsburst-detect
Set OOBST burst monitor max recordsmax-records
maximum number of records to monitorval
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3355
P Commandsplatform qos
Page 3500
platform qos[no] { platform | hardware } qos { afd profile <prof-opts> [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Approximate Fair Droppingafd
AFD profilesprofile
prof-opts
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3356
P Commandsplatform qos
Page 3501
platform qos[no] { platform | hardware } qos { min-buffer qos-group <buff-prof-opts> [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
minimum/reserved buffer selectionmin-buffer
Qos Groupqos-group
buff-prof-opts
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3357
P Commandsplatform qos
Page 3502
platform qos[no] { platform | hardware } qos { ns-mcq3-alias qos-group <qos-grp-val> [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure QoS related configurationqos
Select qos-group to which to divert qos-group-3 Multicast trafficns-mcq3-alias
Qos Groupqos-group
QoS group valueqos-grp-val
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3358
P Commandsplatform qos
Page 3503
platform qos[no] { platform | hardware } qos { ing-pg-hdrm-reserve percent <percent-val> [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Set Ingress PG Headroom reservationing-pg-hdrm-reserve
PG Headroom reservation percentpercent
percent of PG Headroom to reservepercent-val
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3359
P Commandsplatform qos
Page 3504
platform qos[no] { platform | hardware } qos { burst-detect rise-threshold <val> bytes fall-threshold <val> bytes }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Set OOBST burst monitor configsburst-detect
Threshold bytes(queue depth) to start monitoring burstrise-threshold
Value in bytesval
Bytesbytes
Threshold bytes(queue depth) to stop monitoring burstfall-threshold
Value in bytesval
Bytesbytes
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3360
P Commandsplatform qos
Page 3505
platform qos[no] { platform | hardware } qos { oq-drops type <sel> [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
per output queue dropsoq-drops
type of drops - occ/wred/bothtype
sel
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3361
P Commandsplatform qos
Page 3506
platform qos[no] { platform | hardware } qos { oq-stats [ { q0 | q1 | q2 | q3 | q4 | q5 | q6 | q7 | q8 | q9 } ] [ { counter0 |counter1 | counter2 | counter3 | counter4 | counter5 | counter6 | counter7 | counter8 | counter9 } ] type { all |<sel1> [ <sel2> ] } [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
per output queue statisticsoq-stats
(Optional) queueing statistics for qos-group q0 (default)q0
(Optional) queueing statistics for qos-group q1q1
(Optional) queueing statistics for qos-group q2q2
(Optional) queueing statistics for qos-group q3q3
(Optional) queueing statistics for qos-group q4q4
(Optional) queueing statistics for qos-group q5q5
(Optional) queueing statistics for qos-group q6q6
(Optional) queueing statistics for qos-group q7q7
(Optional) queueing statistics for qos-group q8 (cpu)q8
(Optional) queueing statistics for qos-group q9 (span)q9
(Optional) use per-port counter 0counter0
(Optional) use per-port counter 1counter1
(Optional) use per-port counter 2counter2
(Optional) use per-port counter 3counter3
(Optional) use per-port counter 4counter4
(Optional) use per-port counter 5counter5
(Optional) use per-port counter 6counter6
(Optional) use per-port counter 7counter7
(Optional) use per-port counter 8counter8
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3362
P Commandsplatform qos
Page 3507
(Optional) use per-port counter 9counter9
type of statisticstype
aggregated occ-drops + wred-drops + ecn-statsall
sel1
(Optional)sel2
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3363
P Commandsplatform qos
Page 3508
platform qos[no] { platform | hardware } qos { dynamic-packet-prioritization age-period <period> usec [ module <module>] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Dynamic Packet Prioritizationdynamic-packet-prioritization
Aging Periodage-period
Aging Periodperiod
micro secondsusec
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3364
P Commandsplatform qos
Page 3509
platform qos[no] { platform | hardware } qos { dynamic-packet-prioritization max-num-pkts <pkts> [ module <module>] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Dynamic Packet Prioritizationdynamic-packet-prioritization
Maximum number of packets prioritizedmax-num-pkts
Number of packetspkts
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3365
P Commandsplatform qos
Page 3510
platform qos[no] { platform | hardware } qos { etrap age-period <period> usec [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Elephant Trapetrap
Aging Periodage-period
Aging Periodperiod
micro secondsusec
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3366
P Commandsplatform qos
Page 3511
platform qos[no] { platform | hardware } qos { etrap byte-count <count> [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Elephant Trapetrap
Number of bytes to become elephant flowbyte-count
Number of bytescount
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3367
P Commandsplatform qos
Page 3512
platform qos[no] { platform | hardware } qos { etrap bandwidth-threshold <bw> bytes [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Elephant Trapetrap
Bandwidth threshold for elephant flowbandwidth-threshold
Number of bytesbw
Bytesbytes
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3368
P Commandsplatform qos
Page 3513
platform qos[no] { platform | hardware } qos { buffer input peak <sel> [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
buffer config for EX platformsbuffer
input bufferinput
peak counter typepeak
sel
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3369
P Commandsplatform qos
Page 3514
platform qos[no] { platform | hardware } qos { [ cpu-pg-size <cpu-size> ] [ lcpu-pg-size <lcpu-size> ] [ span-pg-size<span-size> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
(Optional) Configure CPU Pool Group thresholdscpu-pg-size
(Optional) Pool Group sizecpu-size
(Optional) Configure LCPU Pool Group thresholdslcpu-pg-size
(Optional) Pool Group sizelcpu-size
(Optional) Configure SPAN Pool Group thresholdsspan-pg-size
(Optional) Pool Group sizespan-size
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3370
P Commandsplatform qos
Page 3515
platform qos buffer peak monitor counter0 class[no] { platform | hardware } qos buffer peak monitor counter0 class <classes>
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
buffer configbuffer
Configure peak controlpeak
monitor peakmonitor
selecting counter 0 for assigning classescounter0
class(es) to monitorclass
qos-groupclasses
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3371
P Commandsplatform qos buffer peak monitor counter0 class
Page 3516
platform qos buffer peak monitor counter1 class[no] { platform | hardware } qos buffer peak monitor counter1 class { <classes> | none }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
buffer configbuffer
Configure peak controlpeak
monitor peakmonitor
selecting counter 1 for assigning classescounter1
class(es) to monitorclass
qos-groupclasses
nonenone
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3372
P Commandsplatform qos buffer peak monitor counter1 class
Page 3517
platform qos classify ns-only[no] { platform | hardware } qos classify ns-only
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Quality Of Serviceqos
Configure qos classificationclassify
Enable qos classification on NS only in hardwarens-only
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3373
P Commandsplatform qos classify ns-only
Page 3518
platform qos eoq[no] { platform | hardware } qos eoq { stats-class qos-group { all | <qos-grp-val> } [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure QoS related configurationqos
Extended Output Queue(EOQ) related configurationeoq
Select class for which to report the statisticsstats-class
Qos Groupqos-group
QoS group valueqos-grp-val
all Qos Groupsall
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3374
P Commandsplatform qos eoq
Page 3519
platform qos include ipg[no] { platform | hardware } qos include { ipg [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
include specific configaration paraminclude
Select whether to include IPG in Shaping/Policingipg
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3375
P Commandsplatform qos include ipg
Page 3520
platform qos ing[no] { platform | hardware } qos { ing-pg-no-min [ pgmin <pgmin> ] [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Enable PG Mining-pg-no-min
(Optional) Set PG Min Valuepgmin
(Optional) PG Min Valuepgmin
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3376
P Commandsplatform qos ing
Page 3521
platform qos ing[no] { platform | hardware } qos { ing-pg-share [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Select Ingress PG Shared Buffer Usageing-pg-share
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3377
P Commandsplatform qos ing
Page 3522
platform qos mac ipg{ platform | hardware } qos mac ipg <val> | no { platform | hardware } qos mac ipg [ <val> ]
Syntax Description
Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
MACmac
Mac IPG Valueipg
new Mac IPG value in byteval
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3378
P Commandsplatform qos mac ipg
Page 3523
platform qos nodrop-PG-thresholds-FX PG-size[no] { platform | hardware } qos nodrop-PG-thresholds-FX PG-size <pg-total>
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Configure No-drop Pool Group thresholds for FX platformsnodrop-PG-thresholds-FX
Configure No-drop Pool Group sizePG-size
Pool Group sizepg-total
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3379
P Commandsplatform qos nodrop-PG-thresholds-FX PG-size
Page 3524
platform qos nodrop-PG-thresholds PG-size[no] { platform | hardware } qos nodrop-PG-thresholds PG-size <pg-total>
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Configure No-drop Pool Group thresholdsnodrop-PG-thresholds
Configure No-drop Pool Group sizePG-size
Pool Group sizepg-total
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3380
P Commandsplatform qos nodrop-PG-thresholds PG-size
Page 3525
platform qos nodrop-PG-thresholds PG-size Red-thresholdYellow-threshold Green-threshold
[no] { platform | hardware } qos nodrop-PG-thresholds PG-size <pg-total> Red-threshold <pg-red>Yellow-threshold <pg-yellow> Green-threshold <pg-green>
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Configure No-drop Pool Group thresholds for EX platformsnodrop-PG-thresholds
Configure No-drop Pool Group sizePG-size
Pool Group sizepg-total
Configure No-drop PG red thresholdRed-threshold
PG red thresholdpg-red
Configure No-drop PG yellow thresholdYellow-threshold
PG yellow thresholdpg-yellow
Configure No-drop PG green thresholdGreen-threshold
PG green thresholdpg-green
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3381
P Commandsplatform qos nodrop-PG-thresholds PG-size Red-threshold Yellow-threshold Green-threshold
Page 3526
platform qos nodrop-queue-thresholds-FX Queue-green[no] { platform | hardware } qos nodrop-queue-thresholds-FX Queue-green <q-green>
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Configure No-drop PG's Queue thresholds for FX platformsnodrop-queue-thresholds-FX
Configure No-drop PG Queue green thresholdQueue-green
PG Queue green thresholdq-green
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3382
P Commandsplatform qos nodrop-queue-thresholds-FX Queue-green
Page 3527
platform qos nodrop-queue-thresholds-roc Queue-green[no] { platform | hardware } qos nodrop-queue-thresholds-roc Queue-green <q-green>
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Configure No-drop PG's Queue thresholdsnodrop-queue-thresholds-roc
Configure No-drop PG Queue green thresholdQueue-green
PG Queue green thresholdq-green
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3383
P Commandsplatform qos nodrop-queue-thresholds-roc Queue-green
Page 3528
platform qos ns[no] { platform | hardware } qos { ns-buffer-profile <buff-prof-opts> [ module <module> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
NorthStar buffer absorption profilesns-buffer-profile
buff-prof-opts
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3384
P Commandsplatform qos ns
Page 3529
platform qos q-noise percent[no] { platform | hardware } qos q-noise percent <noise>
Syntax Description
(Optional) Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure qos related configurationqos
Configure noise thresholdsq-noise
Noise threshold in percentage of dynamic/static queue_maxpercent
Noise percentnoise
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3385
P Commandsplatform qos q-noise percent
Page 3530
platform rate-limiter{ platform | hardware } rate-limiter { layer-3 { <l3-opts> | multicast <mcast-opts> } | layer-2 { <l2-opts> } |<opts> | f1 <f1-opts> } { <pps> [ burst <burst> ] | disable } [ module <module> [ port <start> <end> ] ] | no{ platform | hardware } rate-limiter { layer-3 { <l3-opts> | multicast <mcast-opts> } | layer-2 { <l2-opts> } |<opts> | f1 <f1-opts> } [ disable ] [ <pps> ] [ burst <burst> ] [ module <module> [ port <start> <end> ] ]
Syntax Description
Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure Rate-Limiter for packets forwardedrate-limiter
Layer-3 control and Routed packetslayer-3
l3-opts
Multicast data packetsmulticast
mcast-opts
Layer-2 control and Bridged packetslayer-2
l2-opts
opts
value in packets per secpps
Control packets from F1 modules to supervisorf1
f1-opts
Disable the rate-limiterdisable
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
(Optional) Port rangeport
(Optional) Port start indexstart
(Optional) Port end indexend
(Optional) Modify burst parameterburst
(Optional) value of burst sizeburst
Command Mode
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3386
P Commandsplatform rate-limiter
Page 3531
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3387
P Commandsplatform rate-limiter
Page 3532
platform rate-limiter{ platform | hardware } rate-limiter { layer-3 { <l3-opts> | multicast <mcast-opts> } | layer-2 { <l2-opts> } |<opts> | f1 <f1-opts> } { <pps> [ burst <burst> ] | disable } [ module <module> [ port <start> <end> ] ] | no{ platform | hardware } rate-limiter { layer-3 { <l3-opts> | multicast <mcast-opts> } | layer-2 { <l2-opts> } |<opts> | f1 <f1-opts> } [ disable ] [ <pps> ] [ burst <burst> ] [ module <module> [ port <start> <end> ] ]
Syntax Description
Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure Rate-Limiter for packets forwardedrate-limiter
Layer-3 control and Routed packetslayer-3
l3-opts
Multicast data packetsmulticast
mcast-opts
Layer-2 control and Bridged packetslayer-2
l2-opts
opts
value in kbits per secpps
Control packets from F1 modules to supervisorf1
f1-opts
Disable the rate-limiterdisable
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
(Optional) Port rangeport
(Optional) Port start indexstart
(Optional) Port end indexend
(Optional) Modify burst parameterburst
(Optional) value of burst sizeburst
Command Mode
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3388
P Commandsplatform rate-limiter
Page 3533
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3389
P Commandsplatform rate-limiter
Page 3534
platform rate-limiter access-list-log{ platform | hardware } rate-limiter access-list-log { <pps> [ burst <burst> ] | disable } [ module <module> [port <start> <end> ] ] | no { platform | hardware } rate-limiter access-list-log [ disable ] [ <pps> ] [ burst<burst> ] [ module <module> [ port <start> <end> ] ]
Syntax Description
Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure Rate-Limiter for packets forwardedrate-limiter
Packets copied to supervisor for access-list loggingaccess-list-log
value in packets per secpps
Disable the rate-limiterdisable
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
(Optional) Port rangeport
(Optional) Port start indexstart
(Optional) Port end indexend
(Optional) Modify burst parameterburst
(Optional) value of burst sizeburst
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3390
P Commandsplatform rate-limiter access-list-log
Page 3535
platform rate-limiter span-egress{ platform | hardware } rate-limiter span-egress <rate> [ module <module> ] | no { platform | hardware }rate-limiter span-egress [ <rate> ] [ module <module> ]
Syntax Description
Negate a command or set its defaultsno
Platform configuration commandsplatform
Hardware Internal Informationhardware
Configure Rate-Limiter for packets forwardedrate-limiter
SPAN/ERSPAN egress packetsspan-egress
value in kbit per secrate
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3391
P Commandsplatform rate-limiter span-egress
Page 3536
plb[no] plb [ <svc-name> ] [ service <service-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure PLBplb
(Optional) Specify PLB service name [Deprecated]svc-name
(Optional) Configure PLB service [Preferred]service
(Optional) Specify PLB service nameservice-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3392
P Commandsplb
Page 3537
plb analytics[no] plb analytics <service-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure PLBplb
Enable PLB service analyticsanalytics
PLB service nameservice-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3393
P Commandsplb analytics
Page 3538
plb device-group[no] plb device-group <group-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure PLBplb
Configure PLB device groupdevice-group
Specify device-group namegroup-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3394
P Commandsplb device-group
Page 3539
police[no] police { { [ cir ] { <cir-val> [ bps | kbps | mbps | gbps | pps ] | percent <cir-perc> } [ [ bc ] {<committed-burst> [ bytes | kbytes | mbytes | ms | us | packets ] } ] [ pir { <pir-val> [ bps2 | kbps2 | mbps2 |gbps2 | pps2 ] | percent <pir-perc> } [ [ be ] { <extended-burst> [ bytes2 | kbytes2 | mbytes2 | ms2 | us2 |packets2 ] } ] ] [ conform { transmit | set-prec-transmit { <prec-val> | <prec-enum> } | set-dscp-transmit {<dscp-val> | <dscp-enum> } | set-cos-transmit <cos-val> | set-discard-class-transmit <disc-class-val> |set-qos-transmit <qos-grp-val> | set-mpls-exp-imposition-transmit <exp-value-imp> |set-mpls-exp-topmost-transmit <exp-value-top> } ] [ exceed { transmit1 | drop1 | set <exc-frm-field><exc-to-field> table cir-markdown-map | set-prec-transmit1 { <prec-val1> | <prec-enum1> } | set-dscp-transmit1{ <dscp-val1> | <dscp-enum1> } | set-cos-transmit1 <cos-val1> | set-discard-class-transmit1 <disc-class-val1>| set-qos-transmit1 <qos-grp-val1> | set-mpls-exp-imposition-transmit1 <exp-value-imp1> |set-mpls-exp-topmost-transmit1 <exp-value-top1> } ] [ violate { drop2 | set <vio-frm-field> <vio-to-field>table2 pir-markdown-map | set-prec-transmit2 { <prec-val2> | <prec-enum2> } | set-dscp-transmit2 {<dscp-val2> | <dscp-enum2> } | set-cos-transmit2 <cos-val2> | set-discard-class-transmit2 <disc-class-val2>| set-qos-transmit2 <qos-grp-val2> | set-mpls-exp-imposition-transmit2 <exp-value-imp2> |set-mpls-exp-topmost-transmit2 <exp-value-top2> } ] } | aggregate <policer-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
policepolice
(Optional) Specify committed information ratecir
(Optional) Specify committed burstbc
Specify rate as percentage of interface data-ratepercent
Percentagecir-perc
(Optional) Percentagepir-perc
(Optional) Specify peak information ratepir
(Optional) Specify extended burst (for 1R3C meter)be
(Optional) Bits per secondbps
(Optional) Kilo bits per secondkbps
(Optional) Mega bits per secondmbps
(Optional) Giga bits per secondgbps
(Optional) Packets per secondpps
(Optional) Bits per secondbps2
(Optional) Kilo Bits per secondkbps2
(Optional) Mega Bits per secondmbps2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3395
P Commandspolice
Page 3540
(Optional) Giga Bits per secondgbps2
(Optional) Packets per secondpps2
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Micro second(s)us
(Optional) Milli second(s)ms
(Optional) Packetspackets
(Optional) Bytesbytes2
(Optional) Kilo Byteskbytes2
(Optional) Mega Bytesmbytes2
(Optional) Milli secondsms2
(Optional) Micro secondsus2
(Optional) Packetspackets2
(Optional) Specify a conform actionconform
(Optional) Specify a exceed actionexceed
(Optional) Specify a violate actionviolate
(Optional) Transmit packettransmit
(Optional) Transmit packettransmit1
(Optional) Drop packetdrop1
(Optional) Drop packetdrop2
(Optional) Set precedence and send itset-prec-transmit
(Optional) Set precedence and send itset-prec-transmit1
(Optional) Set precedence and send itset-prec-transmit2
(Optional) Precedence valueprec-val
(Optional) Precedence valueprec-val1
(Optional) Precedence valueprec-val2
(Optional)prec-enum
(Optional)prec-enum1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3396
P Commandspolice
Page 3541
(Optional)prec-enum2
(Optional) Set dscp and send itset-dscp-transmit
(Optional) Set dscp and send itset-dscp-transmit1
(Optional) Set dscp and send itset-dscp-transmit2
(Optional) DSCP valuedscp-val
(Optional) DSCP valuedscp-val1
(Optional) DSCP valuedscp-val2
(Optional)dscp-enum
(Optional)dscp-enum1
(Optional)dscp-enum2
(Optional) Set cos and send itset-cos-transmit
(Optional) Set cos and send itset-cos-transmit1
(Optional) Set cos and send itset-cos-transmit2
(Optional) new cos valuecos-val
(Optional) new cos valuecos-val1
(Optional) new cos valuecos-val2
(Optional) Set discard class and send itset-discard-class-transmit
(Optional) Set discard class and send itset-discard-class-transmit1
(Optional) Set discard class and send itset-discard-class-transmit2
(Optional) new discard-class valuedisc-class-val
(Optional) new discard-class valuedisc-class-val1
(Optional) new discard-class valuedisc-class-val2
(Optional) Set qos-group and send itset-qos-transmit
(Optional) Set qos-group and send itset-qos-transmit1
(Optional) Set qos-group and send itset-qos-transmit2
(Optional) QoS group valueqos-grp-val
(Optional) QoS group valueqos-grp-val1
(Optional) QoS group valueqos-grp-val2
(Optional) set-mpls-exp-imposition-transmitset-mpls-exp-imposition-transmit
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3397
P Commandspolice
Page 3542
(Optional) set-mpls-exp-imposition-transmitset-mpls-exp-imposition-transmit1
(Optional) set-mpls-exp-imposition-transmitset-mpls-exp-imposition-transmit2
(Optional) MPLS imposition valueexp-value-imp
(Optional) MPLS imposition valueexp-value-imp1
(Optional) MPLS imposition valueexp-value-imp2
(Optional) Set MPLS topmost labelset-mpls-exp-topmost-transmit
(Optional) Set MPLS topmost labelset-mpls-exp-topmost-transmit1
(Optional) Set MPLS topmost labelset-mpls-exp-topmost-transmit2
(Optional) MPLS topmost valueexp-value-top
(Optional) MPLS topmost valueexp-value-top1
(Optional) MPLS topmost valueexp-value-top2
(Optional) Set a particular value using table or markdown mapset
(Optional)exc-frm-field
(Optional)exc-to-field
(Optional)vio-frm-field
(Optional)vio-to-field
(Optional) Set using the table-maptable
(Optional) Set using the table-maptable2
(Optional) Markdown map table name for exceed actioncir-markdown-map
(Optional) Markdown map table name for violate actionpir-markdown-map
Choose aggregate policer for current classaggregate
Enter aggregate-policer namepolicer-name
Command Mode
• /exec/configure/policy-map/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3398
P Commandspolice
Page 3543
police[no] police [ { { [ cir ] { <cir-val> [ <opt_kbps_mbps_gbps_pps_cir> ] | percent <cir-perc> } } { [ { [ bc ]<bc-val> [ <opt_kbytes_mbytes_gbytes_bc> ] } ] } { [ { pir { <pir> [ <opt_kbps_mbps_gbps_pps_pir> ] |percent1 <pir-perc> } } [ { [ be ] <be-val> [ <opt_kbytes_mbytes_gbytes_be> ] } ] ] } { [ { conform {<opt_drop_transmit_conform> | { set-cos-transmit <set-cos-val> } | { set-dscp-transmit { <set-dscp-val> |<opt_set_dscp> } } | { set-prec-transmit { <set-prec-val> | <opt_set_prec> } } } } [ { exceed {<opt_drop_transmit_exceed> | { set dscp1 dscp2 table cir-markdown-map } } } ] [ { violate {<opt_drop_transmit_violate> | { set1 dscp3 dscp4 table1 pir-markdown-map } } } ] ] } } ]
Syntax Description
Negate a command or set its defaultsno
Policepolice
(Optional) Specify committed information ratecir
(Optional) Unitsopt_kbps_mbps_gbps_pps_cir
(Optional) Specify rate as percentage of interface data-ratepercent
(Optional) Specify peak information ratepir
(Optional) Unitsopt_kbps_mbps_gbps_pps_pir
(Optional) Specify rate as percentage of interface data-ratepercent1
(Optional) Specify extended burstbe
(Optional) Unitsopt_kbytes_mbytes_gbytes_be
(Optional) Specify committed burstbc
(Optional) Unitsopt_kbytes_mbytes_gbytes_bc
(Optional) Specify a conform actionconform
(Optional) Set the actionopt_drop_transmit_conform
(Optional) Set conform action cos valset-cos-transmit
(Optional) 802.1Q Class of Service valueset-cos-val
(Optional) Set conform action dscp valset-dscp-transmit
(Optional) DSCP valueset-dscp-val
(Optional)opt_set_dscp
(Optional) Set conform action precedence valset-prec-transmit
(Optional) IP Precedence valueset-prec-val
(Optional)opt_set_prec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3399
P Commandspolice
Page 3544
(Optional) Specify a exceed actionexceed
(Optional) Set the actionopt_drop_transmit_exceed
(Optional) Set exceed action to cir-markdown-mapset
(Optional) Exceed from fielddscp1
(Optional) Exceed to fielddscp2
(Optional) To specify table nametable
(Optional) Well known markdown mapcir-markdown-map
(Optional) Specify a violate actionviolate
(Optional) Set the actionopt_drop_transmit_violate
(Optional) Set violate action to pir-markdown-mapset1
(Optional) Violate from fielddscp3
(Optional) Violate to fielddscp4
(Optional) To specify table nametable1
(Optional) Well known markdown mappir-markdown-map
Command Mode
• /exec/configure/pmap/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3400
P Commandspolice
Page 3545
police[no] police [ { { [ cir ] { <cir-val> [ <opt_kbps_mbps_gbps_pps_cir> ] | percent <cir-perc> } } { [ { [ bc ]<bc-val> [ <opt_kbytes_mbytes_gbytes_bc> ] } ] } { [ { pir { <pir> [ <opt_kbps_mbps_gbps_pps_pir> ] |percent1 <pir-perc> } } [ { [ be ] <be-val> [ <opt_kbytes_mbytes_gbytes_be> ] } ] ] } { [ { conform {<opt_drop_transmit_conform> | { set-cos-transmit <set-cos-val> } | { set-dscp-transmit { <set-dscp-val> |<opt_set_dscp> } } | { set-prec-transmit { <set-prec-val> | <opt_set_prec> } } } } [ { exceed {<opt_drop_transmit_exceed> | { set dscp1 dscp2 table cir-markdown-map } } } ] [ { violate {<opt_drop_transmit_violate> | { set1 dscp3 dscp4 table1 pir-markdown-map } } } ] ] } } ]
Syntax Description
Negate a command or set its defaultsno
Policepolice
(Optional) Specify committed information ratecir
(Optional) Unitsopt_kbps_mbps_gbps_pps_cir
(Optional) Specify rate as percentage of interface data-ratepercent
(Optional) Specify peak information ratepir
(Optional) Unitsopt_kbps_mbps_gbps_pps_pir
(Optional) Specify rate as percentage of interface data-ratepercent1
(Optional) Specify extended burstbe
(Optional) Unitsopt_kbytes_mbytes_gbytes_be
(Optional) Specify committed burstbc
(Optional) Unitsopt_kbytes_mbytes_gbytes_bc
(Optional) Specify a conform actionconform
(Optional) Set the actionopt_drop_transmit_conform
(Optional) Set conform action cos valset-cos-transmit
(Optional) 802.1Q Class of Service valueset-cos-val
(Optional) Set conform action dscp valset-dscp-transmit
(Optional) DSCP valueset-dscp-val
(Optional)opt_set_dscp
(Optional) Set conform action precedence valset-prec-transmit
(Optional) IP Precedence valueset-prec-val
(Optional)opt_set_prec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3401
P Commandspolice
Page 3546
(Optional) Specify a exceed actionexceed
(Optional) Set the actionopt_drop_transmit_exceed
(Optional) Set exceed action to cir-markdown-mapset
(Optional) Exceed from fielddscp1
(Optional) Exceed to fielddscp2
(Optional) To specify table nametable
(Optional) Well known markdown mapcir-markdown-map
(Optional) Specify a violate actionviolate
(Optional) Set the actionopt_drop_transmit_violate
(Optional) Set violate action to pir-markdown-mapset1
(Optional) Violate from fielddscp3
(Optional) Violate to fielddscp4
(Optional) To specify table nametable1
(Optional) Well known markdown mappir-markdown-map
Command Mode
• /exec/configure/pmap/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3402
P Commandspolice
Page 3547
police[no] police { { [ cir ] { <cir-val> [ bps | kbps | mbps | gbps ] | percent <cir-perc> } [ [ bc ] { <committed-burst>[ bytes | kbytes | mbytes | ms | us ] } ] [ pir { <pir-val> [ bps2 | kbps2 | mbps2 | gbps2 | pps2 ] | percent <pir-perc>} [ [ be ] { <extended-burst> [ bytes2 | kbytes2 | mbytes2 | ms2 | us2 | packets2 ] } ] ] [ conform { transmit |set-prec-transmit { <prec-val> | <prec-enum> } | set-dscp-transmit { <dscp-val> | <dscp-enum> } |set-cos-transmit <cos-val> | set-discard-class-transmit <disc-class-val> | set-qos-transmit <qos-grp-val> |set-mpls-exp-imposition-transmit <exp-value-imp> | set-mpls-exp-topmost-transmit <exp-value-top> } [exceed { drop1 | set <exc-frm-field> <exc-to-field> table cir-markdown-map | set-prec-transmit1 { <prec-val1>| <prec-enum1> } | set-dscp-transmit1 { <dscp-val1> | <dscp-enum1> } | set-cos-transmit1 <cos-val1> |set-discard-class-transmit1 <disc-class-val1> | set-qos-transmit1 <qos-grp-val1> |set-mpls-exp-imposition-transmit1 <exp-value-imp1> | set-mpls-exp-topmost-transmit1 <exp-value-top1> }] [ violate { drop2 | set <vio-frm-field> <vio-to-field> table2 pir-markdown-map | set-prec-transmit2 {<prec-val2> | <prec-enum2> } | set-dscp-transmit2 { <dscp-val2> | <dscp-enum2> } | set-cos-transmit2<cos-val2> | set-discard-class-transmit2 <disc-class-val2> | set-qos-transmit2 <qos-grp-val2> |set-mpls-exp-imposition-transmit2 <exp-value-imp2> | set-mpls-exp-topmost-transmit2 <exp-value-top2> }] ] } | aggregate <policer-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
policepolice
(Optional) Specify committed information ratecir
(Optional) Specify committed burstbc
Specify rate as percentage of interface data-ratepercent
Percentagecir-perc
(Optional) Percentagepir-perc
(Optional) Specify peak information ratepir
(Optional) Specify extended burst (for 1R3C meter)be
(Optional) Bits per secondbps
(Optional) Kilo bits per secondkbps
(Optional) Mega bits per secondmbps
(Optional) Giga bits per secondgbps
(Optional) Bits per secondbps2
(Optional) Kilo Bits per secondkbps2
(Optional) Mega Bits per secondmbps2
(Optional) Giga Bits per secondgbps2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3403
P Commandspolice
Page 3548
(Optional) Packets per secondpps2
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Micro second(s)us
(Optional) Milli second(s)ms
(Optional) Bytesbytes2
(Optional) Kilo Byteskbytes2
(Optional) Mega Bytesmbytes2
(Optional) Milli secondsms2
(Optional) Micro secondsus2
(Optional) Packetspackets2
(Optional) Specify a conform actionconform
(Optional) Specify a exceed actionexceed
(Optional) Specify a violate actionviolate
(Optional) Transmit packettransmit
(Optional) Drop packetdrop1
(Optional) Drop packetdrop2
(Optional) Set precedence and send itset-prec-transmit
(Optional) Set precedence and send itset-prec-transmit1
(Optional) Set precedence and send itset-prec-transmit2
(Optional) Precedence valueprec-val
(Optional) Precedence valueprec-val1
(Optional) Precedence valueprec-val2
(Optional)prec-enum
(Optional)prec-enum1
(Optional)prec-enum2
(Optional) Set dscp and send itset-dscp-transmit
(Optional) Set dscp and send itset-dscp-transmit1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3404
P Commandspolice
Page 3549
(Optional) Set dscp and send itset-dscp-transmit2
(Optional) DSCP valuedscp-val
(Optional) DSCP valuedscp-val1
(Optional) DSCP valuedscp-val2
(Optional)dscp-enum
(Optional)dscp-enum1
(Optional)dscp-enum2
(Optional) Set cos and send itset-cos-transmit
(Optional) Set cos and send itset-cos-transmit1
(Optional) Set cos and send itset-cos-transmit2
(Optional) new cos valuecos-val
(Optional) new cos valuecos-val1
(Optional) new cos valuecos-val2
(Optional) Set discard class and send itset-discard-class-transmit
(Optional) Set discard class and send itset-discard-class-transmit1
(Optional) Set discard class and send itset-discard-class-transmit2
(Optional) new discard-class valuedisc-class-val
(Optional) new discard-class valuedisc-class-val1
(Optional) new discard-class valuedisc-class-val2
(Optional) Set qos-group and send itset-qos-transmit
(Optional) Set qos-group and send itset-qos-transmit1
(Optional) Set qos-group and send itset-qos-transmit2
(Optional) QoS group valueqos-grp-val
(Optional) QoS group valueqos-grp-val1
(Optional) QoS group valueqos-grp-val2
(Optional) set-mpls-exp-imposition-transmitset-mpls-exp-imposition-transmit
(Optional) set-mpls-exp-imposition-transmitset-mpls-exp-imposition-transmit1
(Optional) set-mpls-exp-imposition-transmitset-mpls-exp-imposition-transmit2
(Optional) MPLS imposition valueexp-value-imp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3405
P Commandspolice
Page 3550
(Optional) MPLS imposition valueexp-value-imp1
(Optional) MPLS imposition valueexp-value-imp2
(Optional) Set MPLS topmost labelset-mpls-exp-topmost-transmit
(Optional) Set MPLS topmost labelset-mpls-exp-topmost-transmit1
(Optional) Set MPLS topmost labelset-mpls-exp-topmost-transmit2
(Optional) MPLS topmost valueexp-value-top
(Optional) MPLS topmost valueexp-value-top1
(Optional) MPLS topmost valueexp-value-top2
(Optional) Set a particular value using table or markdown mapset
(Optional)exc-frm-field
(Optional)exc-to-field
(Optional)vio-frm-field
(Optional)vio-to-field
(Optional) Set using the table-maptable
(Optional) Set using the table-maptable2
(Optional) Markdown map table name for exceed actioncir-markdown-map
(Optional) Markdown map table name for violate actionpir-markdown-map
Choose aggregate policer for current classaggregate
Enter aggregate-policer namepolicer-name
Command Mode
• /exec/configure/policy-map/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3406
P Commandspolice
Page 3551
police police ppspolice { [ cir ] { <cir-val> [ <opt_kbps_mbps_gbps_pps_cir> ] | percent <cir-perc> } } { [ { [ bc ] <bc-val>[ <opt_kbytes_mbytes_gbytes_bc> ] } ] } { [ { pir { <pir> [ <opt_kbps_mbps_gbps_pps_pir> ] | percent1<pir-perc> } } [ { [ be ] <be-val> [ <opt_kbytes_mbytes_gbytes_be> ] } ] ] } { [ { conform {<opt_drop_transmit_conform> | { set-cos-transmit <set-cos-val> } | { set-dscp-transmit { <set-dscp-val> |<opt_set_dscp> } } | { set-prec-transmit { <set-prec-val> | <opt_set_prec> } } } } [ { exceed {<opt_drop_transmit_exceed> | { set dscp1 dscp2 table cir-markdown-map } } } ] [ { violate {<opt_drop_transmit_violate> | { set1 dscp3 dscp4 table1 pir-markdown-map } } } ] ] } | police { pps {<pps-val> } }
Syntax Description
Policepolice
(Optional) Specify committed information ratecir
(Optional) Unitsopt_kbps_mbps_gbps_pps_cir
Specify rate as percentage of interface data-ratepercent
(Optional) Specify peak information ratepir
(Optional) Unitsopt_kbps_mbps_gbps_pps_pir
(Optional) Specify rate as percentage of interface data-ratepercent1
(Optional) Specify extended burstbe
(Optional) Unitsopt_kbytes_mbytes_gbytes_be
(Optional) Specify committed burstbc
(Optional) Unitsopt_kbytes_mbytes_gbytes_bc
(Optional) Specify a conform actionconform
(Optional) Set the actionopt_drop_transmit_conform
(Optional) Set conform action cos valset-cos-transmit
(Optional) 802.1Q Class of Service valueset-cos-val
(Optional) Set conform action dscp valset-dscp-transmit
(Optional) DSCP valueset-dscp-val
(Optional)opt_set_dscp
(Optional) Set conform action precedence valset-prec-transmit
(Optional) IP Precedence valueset-prec-val
(Optional)opt_set_prec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3407
P Commandspolice police pps
Page 3552
(Optional) Specify a exceed actionexceed
(Optional) Set the actionopt_drop_transmit_exceed
(Optional) Set exceed action to cir-markdown-mapset
(Optional) Exceed from fielddscp1
(Optional) Exceed to fielddscp2
(Optional) To specify table nametable
(Optional) Well known markdown mapcir-markdown-map
(Optional) Specify a violate actionviolate
(Optional) Set the actionopt_drop_transmit_violate
(Optional) Set violate action to pir-markdown-mapset1
(Optional) Violate from fielddscp3
(Optional) Violate to fielddscp4
(Optional) To specify table nametable1
(Optional) Well known markdown mappir-markdown-map
Specify PPS rate limitpps
Command Mode
• /exec/configure/pmap/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3408
P Commandspolice police pps
Page 3553
police police ppspolice { [ cir ] { <cir-val> [ <opt_kbps_mbps_gbps_pps_cir> ] | percent <cir-perc> } } { [ { [ bc ] <bc-val>[ <opt_kbytes_mbytes_gbytes_bc> ] } ] } { [ { pir { <pir> [ <opt_kbps_mbps_gbps_pps_pir> ] | percent1<pir-perc> } } [ { [ be ] <be-val> [ <opt_kbytes_mbytes_gbytes_be> ] } ] ] } { [ { conform {<opt_drop_transmit_conform> | { set-cos-transmit <set-cos-val> } | { set-dscp-transmit { <set-dscp-val> |<opt_set_dscp> } } | { set-prec-transmit { <set-prec-val> | <opt_set_prec> } } } } [ { exceed {<opt_drop_transmit_exceed> | { set dscp1 dscp2 table cir-markdown-map } } } ] [ { violate {<opt_drop_transmit_violate> | { set1 dscp3 dscp4 table1 pir-markdown-map } } } ] ] } | police { pps {<pps-val> } }
Syntax Description
Policepolice
(Optional) Specify committed information ratecir
(Optional) Unitsopt_kbps_mbps_gbps_pps_cir
Specify rate as percentage of interface data-ratepercent
(Optional) Specify peak information ratepir
(Optional) Unitsopt_kbps_mbps_gbps_pps_pir
(Optional) Specify rate as percentage of interface data-ratepercent1
(Optional) Specify extended burstbe
(Optional) Unitsopt_kbytes_mbytes_gbytes_be
(Optional) Specify committed burstbc
(Optional) Unitsopt_kbytes_mbytes_gbytes_bc
(Optional) Specify a conform actionconform
(Optional) Set the actionopt_drop_transmit_conform
(Optional) Set conform action cos valset-cos-transmit
(Optional) 802.1Q Class of Service valueset-cos-val
(Optional) Set conform action dscp valset-dscp-transmit
(Optional) DSCP valueset-dscp-val
(Optional)opt_set_dscp
(Optional) Set conform action precedence valset-prec-transmit
(Optional) IP Precedence valueset-prec-val
(Optional)opt_set_prec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3409
P Commandspolice police pps
Page 3554
(Optional) Specify a exceed actionexceed
(Optional) Set the actionopt_drop_transmit_exceed
(Optional) Set exceed action to cir-markdown-mapset
(Optional) Exceed from fielddscp1
(Optional) Exceed to fielddscp2
(Optional) To specify table nametable
(Optional) Well known markdown mapcir-markdown-map
(Optional) Specify a violate actionviolate
(Optional) Set the actionopt_drop_transmit_violate
(Optional) Set violate action to pir-markdown-mapset1
(Optional) Violate from fielddscp3
(Optional) Violate to fielddscp4
(Optional) To specify table nametable1
(Optional) Well known markdown mappir-markdown-map
Specify PPS rate limitpps
Command Mode
• /exec/configure/pmap/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3410
P Commandspolice police pps
Page 3555
policy-map[no] policy-map [ type qos ] [ match-first ] <pmap-name-qos>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a policy mappolicy-map
(Optional) Specify the type of this policy-maptype
(Optional) Qos policyqos
(Optional) Take the action for the first class that matchesmatch-first
Policy-map name (alphanumeric)pmap-name-qos
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3411
P Commandspolicy-map
Page 3556
policy-map type control-plane[no] policy-map type control-plane <pmap-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a policy mappolicy-map
Specify the type of this policy-maptype
Control-Planecontrol-plane
Policy-map name (alphanumeric)pmap-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3412
P Commandspolicy-map type control-plane
Page 3557
policy-map type network-qos[no] policy-map type network-qos <pmap-name-nq>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a policy mappolicy-map
Specify the type of this policy-maptype
Network QoS policynetwork-qos
Policy-map namepmap-name-nq
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3413
P Commandspolicy-map type network-qos
Page 3558
policy-map type queuing[no] policy-map type queuing [ match-first ] <pmap-name-que>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a policy mappolicy-map
Specify the type of this policy-maptype
Queuing policyqueuing
(Optional) Take the action for the first class that matchesmatch-first
Policy-map name (alphanumeric)pmap-name-que
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3414
P Commandspolicy-map type queuing
Page 3559
policy[no] policy { <cfg-pol-name> | <unknown-pol-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
NBM Flow policypolicy
Policy namecfg-pol-name
Policy nameunknown-pol-name
Command Mode
• /exec/configure/nbm-flow-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3415
P Commandspolicy
Page 3560
policypolicy { { dynamic identity <device-id> } | { static sgt <sgt> [ trusted ] } } | no policy static | no policy dynamic
Syntax Description
Enable and define policy to be appliedpolicy
apply to authorization server for policydynamic
specify identity of peer for authorization requestidentity
peer's device-iddevice-id
configure static policystatic
SGT tag for pkts from this devicesgt
sgt valuesgt
(Optional) specify trust state of the linktrusted
Command Mode
• /exec/configure/cts-manual
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3416
P Commandspolicy
Page 3561
policy[no] policy <pol-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Identifying name for policy with max 128 characterspolicy
Configure Policy namepol-name
Command Mode
• /exec/configure/sr/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3417
P Commandspolicy
Page 3562
poppop [ <name> ]
Syntax Description
pop mode from stack or restore from namepop
(Optional) namename
Command Mode
• /global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3418
P Commandspop
Page 3563
port-channel bfd destinationport-channel bfd destination <dest-ip> | no port-channel bfd destination [ <dest-ip> ]
Syntax Description
Negate a command or set its defaultsno
Configure port channel parametersport-channel
BFD parametersbfd
Configure IP address of BFD peerdestination
BFD peer IPv4 addressdest-ip
Command Mode
• /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3419
P Commandsport-channel bfd destination
Page 3564
port-channel bfd startport-channel bfd start <start-timer-value> | no port-channel bfd start [ <start-timer-value> ]
Syntax Description
Negate a command or set its defaultsno
Configure port channel parametersport-channel
BFD parametersbfd
Start timer timeout valuestart
BFD start timer timeout value in seconds (default off)start-timer-value
Command Mode
• /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3420
P Commandsport-channel bfd start
Page 3565
port-channel bfd track-member-linkport-channel bfd track-member-link | no port-channel bfd track-member-link
Syntax Description
Negate a command or set its defaultsno
Configure port channel parametersport-channel
Enable BFDbfd
Enable per-member-link BFD on the port-channel interfacetrack-member-link
Command Mode
• /exec/configure/if-eth-port-channel /exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3421
P Commandsport-channel bfd track-member-link
Page 3566
port-channel fast-convergenceport-channel fast-convergence | no port-channel fast-convergence
Syntax Description
Negate a command or set its defaultsno
Configure port channel parametersport-channel
Enable/Disable port-channel fast convergenefast-convergence
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3422
P Commandsport-channel fast-convergence
Page 3567
port-channel hash-distributionport-channel hash-distribution <type> | no port-channel hash-distribution [ <type> ]
Syntax Description
Negate a command or set its defaultsno
Configure port channel parametersport-channel
Configure port-channel hash-distributionhash-distribution
adaptive/fixed (default adaptive)type
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3423
P Commandsport-channel hash-distribution
Page 3568
port-channel limitport-channel limit | no port-channel limit
Syntax Description
Negate a command or set its defaultsno
Configure the maximum number of supported vPCsport-channel
limit to 244 vPCslimit
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3424
P Commandsport-channel limit
Page 3569
port-channel load-balanceport-channel load-balance <bndl_hash> <bndl_sel> [ rotate <po-lb-rotate-range> ] [ concatenation ] [ module<module> | fex all ] [ symmetric ] | no port-channel load-balance [ <bndl_hash> <bndl_sel> [ rotate<po-lb-rotate-range> ] [ concatenation ] [ module <module> | fex all ] [ symmetric ] ]
Syntax Description
Negate a command or set its defaultsno
Configure port channel parametersport-channel
Configure port-channel load balanceload-balance
bundle hashbndl_hash
bundle selectbndl_sel
(Optional) offset the hash-inputrotate
(Optional) offset the hash-inputpo-lb-rotate-range
(Optional) enable/disable concatenationconcatenation
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
(Optional) FEX devicesfex
(Optional) Permit all FEX to configure port-channel LBall
(Optional) symmetric load balancingsymmetric
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3425
P Commandsport-channel load-balance
Page 3570
port-channel load-balance1 ethernetport-channel load-balance1 ethernet <algorithm> [ symmetric ] | no port-channel load-balance1 ethernet [<algorithm> [ symmetric ] ]
Syntax Description
Negate a command or set its defaultsno
Configure port channel parametersport-channel
Configure port-channel load balanceload-balance1
Ethernet port-channelethernet
Configure port-channel load balancealgorithm
(Optional) symmetric load balancingsymmetric
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3426
P Commandsport-channel load-balance1 ethernet
Page 3571
port-channel load-balance2 resilientport-channel load-balance2 resilient | no port-channel load-balance2 resilient
Syntax Description
Negate a command or set its defaultsno
Configure port channel parametersport-channel
Configure port-channel load balanceload-balance2
Configure port-channel load balance resilient moderesilient
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3427
P Commandsport-channel load-balance2 resilient
Page 3572
port-channel load-balance ethernetport-channel load-balance ethernet <algorithm> [ module <module> ] | no port-channel load-balance ethernet[ <algorithm> [ module <module> ] ]
Syntax Description
Negate a command or set its defaultsno
Configure port channel parametersport-channel
Configure port-channel load balanceload-balance
Ethernet port-channelethernet
(Optional) Specify a module numbermodule
(Optional) Specify a module numbermodule
Configure port-channel load balancealgorithm
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3428
P Commandsport-channel load-balance ethernet
Page 3573
port-channel load-deferport-channel load-defer <load-defer-timeout> | no port-channel load-defer [ <load-defer-timeout> ]
Syntax Description
Negate a command or set its defaultsno
Configure port channel parametersport-channel
Load defer time intervalload-defer
Load defer time interval in seconds (default 120 seconds)load-defer-timeout
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3429
P Commandsport-channel load-defer
Page 3574
port-channel port hash-distributionport-channel port hash-distribution <type> | no port-channel port hash-distribution [ <type> ]
Syntax Description
Negate a command or set its defaultsno
Configure port channel parametersport-channel
Configure port-channel port hash-distributionport
Configure port-channel port hash-distributionhash-distribution
adaptive/fixed (default adaptive)type
Command Mode
• /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel/exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3430
P Commandsport-channel port hash-distribution
Page 3575
port-channel port load-deferport-channel port load-defer | no port-channel port load-defer
Syntax Description
Negate a command or set its defaultsno
Configure port channel parametersport-channel
Configure port-channel load-defer for member portsport
Configure port-channel load-deferload-defer
Command Mode
• /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel/exec/configure/if-eth-port-channel-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3431
P Commandsport-channel port load-defer
Page 3576
port-channel scale-fanoutport-channel scale-fanout | no port-channel scale-fanout
Syntax Description
Negate a command or set its defaultsno
Configure port channel parametersport-channel
Enable/disable port-channel scale-fanout when ports span more than 16ASIC units
scale-fanout
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3432
P Commandsport-channel scale-fanout
Page 3577
port-group{ port-group <name> } | { no port-group <name> }
Syntax Description
Negate a command or set its defaultsno
smart channel port groupport-group
smart channel port group namename
Command Mode
• /exec/configure/smartc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3433
P Commandsport-group
Page 3578
port-group{ port-group <name> } | { no port-group <name> }
Syntax Description
Negate a command or set its defaultsno
catena port groupport-group
catena port group namename
Command Mode
• /exec/configure/catena
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3434
P Commandsport-group
Page 3579
port-license[no] port-license [ acquire ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable port activation licenseport-license
(Optional) Acquire port activation licenseacquire
Command Mode
• /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3435
P Commandsport-license
Page 3580
port-license[no] port-license [ acquire ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable port activation licenseport-license
(Optional) Acquire port activation licenseacquire
Command Mode
• /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3436
P Commandsport-license
Page 3581
port-profile[no] port-profile [ type <typeval> ] { <profilename> | <s0> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a port-profileport-profile
Enter the name of the profileprofilename
Enter the name of the profiles0
(Optional) configure type of the profiletype
(Optional)typeval
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3437
P Commandsport-profile
Page 3582
port-type[no] port-type <type>
Syntax Description
(Optional) Negate a command or set its defaultsno
Identifies if port is fabric-facing or notport-type
Facing port-typetype
Command Mode
• /exec/configure/if-eth-non-member /exec/configure/if-port-channel /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3438
P Commandsport-type
Page 3583
port{ port <sport> <dport> }
Syntax Description
L4 port infoport
Source portsport
Destination portdport
Command Mode
• /exec/configure/configngoamccpayload
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3439
P Commandsport
Page 3584
port{ no port | port <value> }
Syntax Description
no
Port on which to listenport
Max port valuevalue
Command Mode
• /exec/configure/config-twamp-srvr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3440
P Commandsport
Page 3585
port control[no] port control <port-control-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD portport
controlcontrol
Port control nameport-control-name
Command Mode
• /exec/configure/itd-inout
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3441
P Commandsport control
Page 3586
port control[no] port control <port-control-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure PLB port controlport
controlcontrol
Port control nameport-control-name
Command Mode
• /exec/configure/plb-inout
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3442
P Commandsport control
Page 3587
port destination{ port { destination | source } <port> } | { no port { destination | source } }
Syntax Description
Negate a command or set its defaultsno
specify flow port addressport
specify flow source port addresssource
specify flow destination port addressdestination
port numberport
Command Mode
• /exec/configure/configngoamprofileflow
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3443
P Commandsport destination
Page 3588
port type ethernet[no] port <port-range> type { ethernet | fc }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a portport
Enter a port rangeport-range
Configure a port typetype
Ethernet Portethernet
FC Portfc
Command Mode
• /exec/configure/slot
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3444
P Commandsport type ethernet
Page 3589
postcard-telemetry exporter[no] postcard-telemetry exporter <exportername>
Syntax Description
Enable/Disable postcard telemetry configurationpostcard-telemetry
Define a events Exporterexporter
Name of event Exporterexportername
Command Mode
• /exec/configure/config-postcard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3445
P Commandspostcard-telemetry exporter
Page 3590
postcard-telemetry flow-profile[no] postcard-telemetry flow-profile
Syntax Description
Enable/Disable postcard telemetry configurationpostcard-telemetry
Define a POSTCARD flow-profileflow-profile
Command Mode
• /exec/configure/config-postcard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3446
P Commandspostcard-telemetry flow-profile
Page 3591
postcard-telemetry monitor[no] postcard-telemetry monitor <monitorname>
Syntax Description
Enable/Disable postcard telemetry configurationpostcard-telemetry
Define a POSTCARD Monitormonitor
Name of POSTCARD Monitormonitorname
Command Mode
• /exec/configure/config-postcard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3447
P Commandspostcard-telemetry monitor
Page 3592
postcard-telemetry queue-profile[no] postcard-telemetry queue-profile <queue_profilename>
Syntax Description
Enable/Disable postcard telemetry configurationpostcard-telemetry
Define a POSTCARD queue_profilequeue-profile
Name of POSTCARD queue_profilequeue_profilename
Command Mode
• /exec/configure/config-postcard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3448
P Commandspostcard-telemetry queue-profile
Page 3593
postcard-telemetry system monitor[no] postcard-telemetry system monitor <monitorname>
Syntax Description
global configsystem
postcard global settingspostcard-telemetry
postcard Monitor to be appliedmonitor
postcard Monitor to be appliedmonitorname
Command Mode
• /exec/configure/config-postcard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3449
P Commandspostcard-telemetry system monitor
Page 3594
postcard-telemetry watchlist ip[no] postcard-telemetry watchlist ip <watchlistname>
Syntax Description
Enable/Disable postcard telemetry configurationpostcard-telemetry
Define a POSTCARD watchlistwatchlist
Configure POSTCARD IP watchlistip
Name of POSTCARD watchlistwatchlistname
Command Mode
• /exec/configure/config-postcard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3450
P Commandspostcard-telemetry watchlist ip
Page 3595
power efficient-ethernet auto[no] power efficient-ethernet auto
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure EEE for the portpower
Configure Energy Efficient Ethernet (EEE)efficient-ethernet
Auto negotiate EEEauto
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3451
P Commandspower efficient-ethernet auto
Page 3596
power efficient-ethernet sleep threshold aggressive[no] power efficient-ethernet sleep threshold aggressive
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure EEE for the portpower
Configure Energy Efficient Ethernet (EEE)efficient-ethernet
EEE LPI sleep configurationsleep
EEE LPI sleep thresholdthreshold
Enable/ Disable EEE LPI aggressive sleep modeaggressive
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3452
P Commandspower efficient-ethernet sleep threshold aggressive
Page 3597
power inline{ power inline { <port-mode-never> | <port-mode> [ max <wattage> ] } } | { no power inline {<port-mode-never> | <port-mode> } }
Syntax Description
Negate a command or set its defaultsno
Power over Ethernetpower
configure POE port modeport-mode-never
configure POE port modeport-mode
(Optional) Configure the max power per interfacemax
(Optional) milli-wattswattage
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3453
P Commandspower inline
Page 3598
power inline default_consumption{ power inline default_consumption <wattage> } | { no power inline default_consumption }
Syntax Description
Negate a command or set its defaultsno
Power over Ethernetpower
POE port default consumptiondefault_consumption
milli-wattswattage
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3454
P Commandspower inline default_consumption
Page 3599
power inline police action{ power inline police action <police-action> } | { no power inline police action }
Syntax Description
Negate a command or set its defaultsno
Power over Ethernetpower
Configure POE port police parameterspolice
Configure action in port when power allocation exceedsaction
configure POE port actionpolice-action
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3455
P Commandspower inline police action
Page 3600
power inline port priority{ power inline port priority <port-priority> } | { no power inline port priority <port-priority> }
Syntax Description
Negate a command or set its defaultsno
Power over Ethernetpower
Configure POE port parametersport
Configure the priority for the portpriority
configure POE port priorityport-priority
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3456
P Commandspower inline port priority
Page 3601
power redundancy-mode combined[no] power redundancy-mode combined
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure power supplypower
Configure power supply redundancy moderedundancy-mode
Configure power supply redundancy mode as combinedcombined
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3457
P Commandspower redundancy-mode combined
Page 3602
power redundancy-mode combined force[no] power redundancy-mode combined force
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure power supplypower
Configure power supply redundancy moderedundancy-mode
Configure power supply redundancy mode as combinedcombined
Force combined mode without promptingforce
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3458
P Commandspower redundancy-mode combined force
Page 3603
power redundancy-mode insrc-redundant[no] power redundancy-mode insrc-redundant
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure power supplypower
Configure power supply redundancy moderedundancy-mode
Configure power supply redundancy mode as grid/AC input sourceredundant
insrc-redundant
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3459
P Commandspower redundancy-mode insrc-redundant
Page 3604
power redundancy-mode ps-redundant[no] power redundancy-mode ps-redundant
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure power supplypower
Configure power supply redundancy moderedundancy-mode
Configure power supply redundancy mode as PS redundantps-redundant
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3460
P Commandspower redundancy-mode ps-redundant
Page 3605
power reserve[no] power reserve <percentage>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure power supplypower
Override default power reservationreserve
please enter a percentagepercentage
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3461
P Commandspower reserve
Page 3606
poweroff[no] poweroff { module <lem-aware-module> | <s0> <santa-cruz-range> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Power off a module in the switchpoweroff
enter a module numbermodule
please enter the module numberlem-aware-module
Power off a specific xbars0
please enter the xbar numbersanta-cruz-range
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3462
P Commandspoweroff
Page 3607
ppspps <pps> <burst> | no pps [ <pps> ] [ <burst> ]
Syntax Description
Negate a command or set its defaultsno
OSPF packets per secondpps
Packets per second valuepps
Burst valueburst
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3463
P Commandspps
Page 3608
ppspps <pps> <burst> | no pps [ <pps> ] [ <burst> ]
Syntax Description
Negate a command or set its defaultsno
OSPFv3 packets per secondpps
Packets per second valuepps
Burst valueburst
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3464
P Commandspps
Page 3609
precision milliseconds{ { no | default } precision | precision { milliseconds | microseconds } }
Syntax Description
no
millisecondsprecision
Set a command to its defaultsdefault
Set precision of measurementprecision
Precision microsecondsmicroseconds
Precision millisecondsmilliseconds
Command Mode
• /exec/configure/ip-sla/jitter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3465
P Commandsprecision milliseconds
Page 3610
preempt[no] preempt | preempt
Syntax Description
Negate a command or set its defaultsno
Enable preemption of lower priority Masterpreempt
Command Mode
• /exec/configure/if-eth-any/vrrpv3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3466
P Commandspreempt
Page 3611
preempt[no] preempt
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable preemption of lower priority masterpreempt
Command Mode
• /exec/configure/if-eth-any/vrrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3467
P Commandspreempt
Page 3612
preempt delay minimum[no] preempt delay | preempt delay minimum <secs>
Syntax Description
Negate a command or set its defaultsno
Enable preemption of lower priority Masterpreempt
Wait before preemptingdelay
Delay at least this longminimum
Seconds to delaysecs
Command Mode
• /exec/configure/if-eth-any/vrrpv3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3468
P Commandspreempt delay minimum
Page 3613
preempt delay minimum reload sync preempt delay reloadminimum sync preempt delay sync minimum reload preemptdelayreloadsyncminimumpreemptdelaysyncreloadminimumpreempt delay minimum sync reload preempt delay reload syncpreempt delay sync reload preempt delay minimum syncpreempt delay sync minimum preempt delay minimum reloadpreemptdelayreloadminimumpreemptdelayminimumpreemptdelay reload preempt delay sync preempt
preempt delayminimum<min-delay> reload <rel-delay> sync <sync-delay> | preempt delay reload <rel-delay>minimum <min-delay> sync <sync-delay> | preempt delay sync <sync-delay> minimum <min-delay> reload<rel-delay> | preempt delay reload <rel-delay> sync <sync-delay> minimum <min-delay> | preempt delaysync <sync-delay> reload <rel-delay> minimum <min-delay> | preempt delay minimum <min-delay> sync<sync-delay> reload <rel-delay> | preempt delay reload <rel-delay> sync <sync-delay> | preempt delay sync<sync-delay> reload <rel-delay> | preempt delay minimum <min-delay> sync <sync-delay> | preempt delaysync <sync-delay>minimum<min-delay> | preempt delayminimum<min-delay> reload <rel-delay> | preemptdelay reload <rel-delay> minimum <min-delay> | preempt delay minimum <min-delay> | preempt delayreload <rel-delay> | preempt delay sync <sync-delay> | preempt | no preempt | no preempt delay [ { minimum[ <min-delay> ] [ [ reload [ <rel-delay> ] ] [ sync [ <sync-delay> ] ] | [ sync [ <sync-delay> ] ] [ reload [<rel-delay> ] ] ] | reload [ <rel-delay> ] [ [ minimum [ <min-delay> ] ] [ sync [ <sync-delay> ] ] | [ sync [<sync-delay> ] ] [ minimum [ <min-delay> ] ] ] | sync [ <sync-delay> ] [ [ reload [ <rel-delay> ] ] [ minimum[ <min-delay> ] ] | [ minimum [ <min-delay> ] ] [ reload [ <rel-delay> ] ] ] } ]
Syntax Description
Negate a command or set its defaultsno
Overthrow lower priority Active routerspreempt
Wait before preemptingdelay
Delay at least this longminimum
Number of seconds for minimum delaymin-delay
Delay after reloadreload
Number of seconds for reload delayrel-delay
Wait for IP redundancy clientssync
Number of seconds for sync delaysync-delay
Command Mode
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3469
P Commandspreempt delay minimum reload sync preempt delay reload minimum sync preempt delay sync minimum reload preempt delay reload sync minimum preempt
delay sync reload minimum preempt delay minimum sync reload preempt delay reload sync preempt delay sync reload preempt delay minimum sync preemptdelay sync minimum preempt delay minimum reload preempt delay reload minimum preempt delay minimum preempt delay reload preempt delay sync preempt
Page 3614
• /exec/configure/if-eth-any/hsrp_ipv4 /exec/configure/if-eth-any/hsrp_ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3470
P Commandspreempt delay minimum reload sync preempt delay reload minimum sync preempt delay sync minimum reload preempt delay reload sync minimum preemptdelay sync reload minimum preempt delay minimum sync reload preempt delay reload sync preempt delay sync reload preempt delay minimum sync preemptdelay sync minimum preempt delay minimum reload preempt delay reload minimum preempt delay minimum preempt delay reload preempt delay sync preempt
Page 3615
preference[no] preference <pref>
Syntax Description
(Optional) Negate a command or set its defaultsno
Policy path-option preference entrypreference
Path-option preferencepref
Command Mode
• /exec/configure/sr/te/pol
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3471
P Commandspreference
Page 3616
preference max[no] preference max <pref-val>
Syntax Description
(Optional) Negate a command or set its defaultsno
maximum valuepref-val
Command Mode
• /exec/configure/config-dhcp-guard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3472
P Commandspreference max
Page 3617
preference min[no] preference min <pref-val>
Syntax Description
(Optional) Negate a command or set its defaultsno
maximum valuepref-val
Command Mode
• /exec/configure/config-dhcp-guard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3473
P Commandspreference min
Page 3618
prefix out[ no | default ] { prefix-list <prfxlist-name> } { out | in }
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Apply prefix-listprefix-list
Name of prefix-listprfxlist-name
Apply policy to outgoing routesout
Apply policy to incoming routesin
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3474
P Commandsprefix out
Page 3619
priority-flow-control auto-restore multiplier[no] priority-flow-control auto-restore multiplier { <val> }
Syntax Description
(Optional) Negate the commandno
pfc related commandspriority-flow-control
auto restoreauto-restore
Auto restore multipliermultiplier
Auto multiplier valueval
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3475
P Commandspriority-flow-control auto-restore multiplier
Page 3620
priority-flow-control fixed-restore multiplier[no] priority-flow-control fixed-restore multiplier { <val> }
Syntax Description
(Optional) Negate the commandno
pfc related commandspriority-flow-control
fixed restorefixed-restore
Fixed restore multipliermultiplier
Fixed multiplier valueval
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3476
P Commandspriority-flow-control fixed-restore multiplier
Page 3621
priority-flow-control inn-recover interfacepriority-flow-control inn-recover interface <if_list>
Syntax Description
Change PFC settingspriority-flow-control
Recover PFC queue from stuck stateinn-recover
Interfaceinterface
List of interfacesif_list
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3477
P Commandspriority-flow-control inn-recover interface
Page 3622
priority-flow-control mode[no] priority-flow-control mode { auto | on | off } [ force ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/Disable PFCpriority-flow-control
PFC Modemode
Set Auto Modeauto
Force PFC to Onon
Force PFC to Offoff
(Optional) Force apply PFC configforce
Command Mode
• /exec/configure/if-switching /exec/configure/if-routing /exec/configure/if-port-channel/exec/configure/if-port-channel-sub
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3478
P Commandspriority-flow-control mode
Page 3623
priority-flow-control override-interface mode off[no] priority-flow-control override-interface mode off
Syntax Description
(Optional) Negate a command or set its defaultsno
Global priority-flow-control settingspriority-flow-control
Overrides interface priority-flow-control modeoverride-interface
Priority-flow-control modemode
Offoff
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3479
P Commandspriority-flow-control override-interface mode off
Page 3624
priority-flow-control recover interfacepriority-flow-control recover interface <if_list> [ qos-group <qgrp-num> ] [ module <module_idx> ] [ instance<inst> ]
Syntax Description
Change PFC settingspriority-flow-control
Recover PFC queue from stuck staterecover
Interfaceinterface
List of interfacesif_list
(Optional) No-drop class to be recoveredqos-group
(Optional) qos-group number of the no-drop classqgrp-num
(Optional) Slot/modulemodule
(Optional) Slot/module numbermodule_idx
(Optional) ASIC Instance Numberinstance
(Optional) ASIC Instance Number in Decimalinst
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3480
P Commandspriority-flow-control recover interface
Page 3625
priority-flow-control tah-recover interfacepriority-flow-control tah-recover interface <if_list> [ qos-group <qos> ] [ module <module> ]
Syntax Description
Change PFC settingspriority-flow-control
Recover PFC queue from stuck statetah-recover
Interfaceinterface
List of interfacesif_list
(Optional) No-drop class to be recoveredqos-group
(Optional) qos-group number of the no-drop classqos
(Optional) Slot/modulemodule
(Optional) Slot/module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3481
P Commandspriority-flow-control tah-recover interface
Page 3626
priority-flow-control watch-dog-interval on[no] priority-flow-control watch-dog-interval { on [ disable-action ] [ interface-multiplier <multiplier-val> ]| off }
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/Disable PFCpriority-flow-control
Watch dog intervalwatch-dog-interval
PFC watch-dog interval to Onon
(Optional) Only generate syslog for stuck queue, no actiondisable-action
(Optional) Shutdown multiplier valueinterface-multiplier
(Optional) Shutdown mutlipler valuemultiplier-val
PFC watch-dog interval to Offoff
Command Mode
• /exec/configure/if-switching /exec/configure/if-routing /exec/configure/if-port-channel/exec/configure/if-port-channel-sub
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3482
P Commandspriority-flow-control watch-dog-interval on
Page 3627
priority-flow-control watch-dog-interval on[no] priority-flow-control watch-dog-interval { on | off }
Syntax Description
(Optional) Negate the commandno
Enable/Disable PFCpriority-flow-control
Watch dog intervalwatch-dog-interval
Enable PFC watch-dog interval globallyon
Disable PFC watch-dog interval globallyoff
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3483
P Commandspriority-flow-control watch-dog-interval on
Page 3628
priority-flow-control watch-dog forced on[no] priority-flow-control watch-dog forced { on | off }
Syntax Description
(Optional) Negate the commandno
pfc related commandspriority-flow-control
watch dog intervalwatch-dog
Force enable watch-dog behaviour globallyforced
Enable PFC watch-dog globallyon
Disable PFC watch-dog globallyoff
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3484
P Commandspriority-flow-control watch-dog forced on
Page 3629
priority-flow-control watch-dog interval[no] priority-flow-control watch-dog interval <interval-val>
Syntax Description
(Optional) Negate the commandno
pfc related commandspriority-flow-control
watch dog intervalwatch-dog
Poll intervalinterval
Watch dog interval value in msinterval-val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3485
P Commandspriority-flow-control watch-dog interval
Page 3630
priority-flow-control watch-dog shutdown-multiplier[no] priority-flow-control watch-dog shutdown-multiplier { <val> }
Syntax Description
(Optional) Negate the commandno
pfc related commandspriority-flow-control
watch dog intervalwatch-dog
Shutdown multipliershutdown-multiplier
Shutdown multiplierval
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3486
P Commandspriority-flow-control watch-dog shutdown-multiplier
Page 3631
priority{ priority <priority_value> [ forwarding-threshold lower <lower-value> upper <upper-value> ] | no priority[ forwarding-threshold ] }
Syntax Description
Negate a command or set its defaultsno
Configure the vr prioritypriority
Configure the vr prioritypriority_value
(Optional) Set forwarding thresholdforwarding-threshold
(Optional) Set lower threshold valuelower
(Optional) Lower threshold valuelower-value
(Optional) Set upper threshold valueupper
(Optional) Upper threshold valueupper-value
Command Mode
• /exec/configure/if-eth-any/vrrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3487
P Commandspriority
Page 3632
priority2[no] priority2 [ level2 <value> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure traffic class prioritypriority2
(Optional) Specify level of prioritylevel2
(Optional) Strict-priority level (1=hi 2=med 3=lo)value
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3488
P Commandspriority2
Page 3633
prioritypriority <priority> [ forwarding-threshold lower <lower-value> upper <upper-value> ] | no priority [forwarding-threshold ]
Syntax Description
Negate a command or set its defaultsno
Priority levelpriority
Priority valuepriority
(Optional) Set forwarding thresholdforwarding-threshold
(Optional) Set lower threshold valuelower
(Optional) Lower threshold valuelower-value
(Optional) Set upper threshold valueupper
(Optional) Upper threshold valueupper-value
Command Mode
• /exec/configure/if-eth-any/hsrp_ipv4 /exec/configure/if-eth-any/hsrp_ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3489
P Commandspriority
Page 3634
prioritypriority <value> | no priority
Syntax Description
Negate a command or set its defaultsno
Configure Bundle prioritypriority
Priority valuevalue
Command Mode
• /exec/configure/anycast
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3490
P Commandspriority
Page 3635
priority[no] priority [ level <value> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure traffic class prioritypriority
(Optional) Specify level of prioritylevel
(Optional) Value of level, lower the number higher the priorityvalue
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3491
P Commandspriority
Page 3636
priority[no] priority | priority <val>
Syntax Description
Negate a command or set its defaultsno
Priority of this VRRP grouppriority
Priority levelval
Command Mode
• /exec/configure/if-eth-any/vrrpv3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3492
P Commandspriority
Page 3637
priority[no] priority | priority <setup_prio> [ <hold_prio> ]
Syntax Description
Negate a command or set its defaultsno
Specify LSP prioritypriority
setup prioritysetup_prio
(Optional) hold priorityhold_prio
Command Mode
• /exec/configure/te/lsp-attr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3493
P Commandspriority
Page 3638
priority[no] priority | priority <setup_pri> [ <hold_pri> ]
Syntax Description
Negate a command or set its defaultsno
tunnel prioritypriority
setup prioritysetup_pri
(Optional) hold priorityhold_pri
Command Mode
• /exec/configure/if-te /exec/configure/tunnel-te/cbts-member
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3494
P Commandspriority
Page 3639
private-vlan[no] private-vlan <pvlan-type>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a private VLANprivate-vlan
PVLAN Typepvlan-type
Command Mode
• /exec/configure/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3495
P Commandsprivate-vlan
Page 3640
private-vlan association{ private-vlan association [ { add | remove } ] <secondary_vlans> } | { no private-vlan association [<secondary_vlans> ] }
Syntax Description
Configure a private VLANprivate-vlan
Add association between private VLANsassociation
(Optional) Add a VLAN to private VLAN listadd
(Optional) Remove a VLAN from private VLAN listremove
Negate a command or set its defaultsno
VLAN IDs of the private VLANs to be configuredsecondary_vlans
Command Mode
• /exec/configure/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3496
P Commandsprivate-vlan association
Page 3641
private-vlan mapping{ private-vlan mapping [ { add | remove } ] <secondary_vlans> } | { no private-vlan mapping [<secondary_vlans> ] }
Syntax Description
Configure a private VLANprivate-vlan
Set the private VLAN interface mappingmapping
(Optional) Add a VLAN to private VLAN listadd
(Optional) Remove a VLAN from private VLAN listremove
Negate a command or set its defaultsno
Secondary VLAN IDs of the private VLAN interface mappingsecondary_vlans
Command Mode
• /exec/configure/if-vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3497
P Commandsprivate-vlan mapping
Page 3642
private-vlan synchronizeprivate-vlan synchronize
Syntax Description
Set private-vlan synchronizationprivate-vlan
Synchronize vlanssynchronize
Command Mode
• /exec/configure/spanning-tree/mst/configuration
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3498
P Commandsprivate-vlan synchronize
Page 3643
probe-intervalprobe-interval <probeinterval-val> | no probe-interval
Syntax Description
Negate a command or set its defaultsno
OpenFlow controller probe interval timer (default is 180 seconds)probe-interval
probe interval timer value in secsprobeinterval-val
Command Mode
• /exec/configure/openflow/switch/sub-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3499
P Commandsprobe-interval
Page 3644
probe-intervalprobe-interval <probeinterval-val> | no probe-interval
Syntax Description
Negate a command or set its defaultsno
OpenFlow controller probe interval timer (default is 180 seconds)probe-interval
probe interval timer value in secsprobeinterval-val
Command Mode
• /exec/configure/openflow/switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3500
P Commandsprobe-interval
Page 3645
probe{ probe <probe-id-icmp> [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> |retry-up-count <up-count> | ip <ip-addr> ] + } | { no probe }
Syntax Description
Negate a command or set its defaultsno
Catena probeprobe
Service modeprobe-id-icmp
(Optional) Frequency in secondsfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeout in secondstimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
(Optional) ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/catena-device-grp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3501
P Commandsprobe
Page 3646
probe[no] probe <probe-id-icmp> [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> |retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD probeprobe
Service modeprobe-id-icmp
(Optional) Frequency in secondsfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeout in secondstimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
(Optional) ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/itd-dg-node
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3502
P Commandsprobe
Page 3647
probe[no] probe <probe-id-icmp> [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> |retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD probeprobe
Service modeprobe-id-icmp
(Optional) Frequency in secondsfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeout in secondstimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
(Optional) ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/itd-dg-node-standby
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3503
P Commandsprobe
Page 3648
probe[no] probe <probe-id-icmp> [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> |retry-up-count <up-count> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD probeprobe
Service modeprobe-id-icmp
(Optional) Frequency in secondsfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeout in secondstimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
Command Mode
• /exec/configure/itd-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3504
P Commandsprobe
Page 3649
probe[no] probe <probe-id-icmp> [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> |retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure probe for nodeprobe
Service modeprobe-id-icmp
(Optional) Configure probe frequency for a nodefrequency
(Optional) Frequency in secondsfreq-num
(Optional) Configure probe timeout for a nodetimeout
(Optional) Timeout in secondstimeout
(Optional) Configure retry-count before node declared downretry-down-count
(Optional) Countcount
(Optional) Configure retry-count after node declared upretry-up-count
(Optional) Countup-count
(Optional) Configure ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/plb-dg-node
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3505
P Commandsprobe
Page 3650
probe[no] probe <probe-id-icmp> [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> |retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure probe for nodeprobe
Service modeprobe-id-icmp
(Optional) Configure probe frequency for a nodefrequency
(Optional) Frequency in secondsfreq-num
(Optional) Configure probe timeout for a nodetimeout
(Optional) Timeout in secondstimeout
(Optional) Configure retry-count before node declared downretry-down-count
(Optional) Countcount
(Optional) Configure retry-count after node declared upretry-up-count
(Optional) Countup-count
(Optional) Configure ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/plb-dg-node-standby
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3506
P Commandsprobe
Page 3651
probe[no] probe <probe-id-icmp> [ frequency <freq-num> | timeout <timeout> | retry-down-count <count> |retry-up-count <up-count> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure probe for nodeprobe
Service modeprobe-id-icmp
(Optional) Configure probe frequency for a nodefrequency
(Optional) Frequency in secondsfreq-num
(Optional) Configure probe timeout for a nodetimeout
(Optional) Timeout in secondstimeout
(Optional) Configure retry-count before node declared downretry-down-count
(Optional) Countcount
(Optional) Configure retry-count after node declared upretry-up-count
(Optional) Countup-count
Command Mode
• /exec/configure/plb-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3507
P Commandsprobe
Page 3652
probe get[no] probe <probe-id-http> get [ <url-name> | cache | frequency <freq-num> | timeout <timeout> |retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD probeprobe
Service modeprobe-id-http
Host name/Target addressget
(Optional) Specify only the user input text/filename.http://<node-ip>/<user input>
url-name
(Optional) Use cachecache
(Optional) Frequencyfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeouttimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
(Optional) ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/itd-dg-node
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3508
P Commandsprobe get
Page 3653
probe get{ probe <probe-id-http> get [ <url-name> | cache | frequency <freq-num> | timeout <timeout> | retry-down-count<count> | retry-up-count <up-count> | ip <ip-addr> ] + } | { no probe }
Syntax Description
Negate a command or set its defaultsno
Catena probeprobe
Service modeprobe-id-http
Host name/Target addressget
(Optional) Specify only the user input text/filename.http://<node-ip>/<user input>
url-name
(Optional) Use cachecache
(Optional) Frequencyfrequency
(Optional) Frequencyfreq-num
(Optional) Timeouttimeout
(Optional) Timeouttimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
(Optional) ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/catena-device-grp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3509
P Commandsprobe get
Page 3654
probe get[no] probe <probe-id-http> get [ <url-name> | cache | frequency <freq-num> | timeout <timeout> |retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD probeprobe
Service modeprobe-id-http
Host name/Target addressget
(Optional) Specify only the user input text/filename.http://<node-ip>/<user input>
url-name
(Optional) Use cachecache
(Optional) Frequencyfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeouttimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
(Optional) ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/itd-dg-node-standby
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3510
P Commandsprobe get
Page 3655
probe get[no] probe <probe-id-http> get [ <url-name> | cache | frequency <freq-num> | timeout <timeout> |retry-down-count <count> | retry-up-count <up-count> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD probeprobe
Service modeprobe-id-http
Host name/Target addressget
(Optional) Specify only the user input text/filename.http://<node-ip>/<user input>
url-name
(Optional) Use cachecache
(Optional) Frequencyfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeouttimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
Command Mode
• /exec/configure/itd-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3511
P Commandsprobe get
Page 3656
probe host{ probe <probe-id-dns> host <host-name> [ frequency <freq-num> | timeout <timeout> | retry-down-count<count> | retry-up-count <up-count> | ip <ip-addr> ] + } | { no probe }
Syntax Description
Negate a command or set its defaultsno
Catena probeprobe
Service modeprobe-id-dns
Host name/Target addresshost
DNS Target IP Address or Hostnamehost-name
(Optional) Frequencyfrequency
(Optional) Frequencyfreq-num
(Optional) Timeouttimeout
(Optional) Timeouttimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
(Optional) ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/catena-device-grp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3512
P Commandsprobe host
Page 3657
probe host[no] probe <probe-id-dns> host <host-name> [ frequency <freq-num> | timeout <timeout> | retry-down-count<count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD probeprobe
Service modeprobe-id-dns
Host name/Target addresshost
DNS Target IP Address or Hostnamehost-name
(Optional) Frequencyfrequency
(Optional) Frequencyfreq-num
(Optional) Timeouttimeout
(Optional) Timeouttimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
(Optional) ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/itd-dg-node
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3513
P Commandsprobe host
Page 3658
probe host[no] probe <probe-id-dns> host <host-name> [ frequency <freq-num> | timeout <timeout> | retry-down-count<count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD probeprobe
Service modeprobe-id-dns
Host name/Target addresshost
DNS Target IP Address or Hostnamehost-name
(Optional) Frequency in secondsfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeout in secondstimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
(Optional) ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/itd-dg-node-standby
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3514
P Commandsprobe host
Page 3659
probe host[no] probe <probe-id-dns> host <host-name> [ frequency <freq-num> | timeout <timeout> | retry-down-count<count> | retry-up-count <up-count> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD probeprobe
Service modeprobe-id-dns
Host name/Target addresshost
DNS Target IP Address or Hostnamehost-name
(Optional) Frequency in secondsfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeout in secondstimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
Command Mode
• /exec/configure/itd-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3515
P Commandsprobe host
Page 3660
probe host[no] probe <probe-id-dns> host <host-name> [ frequency <freq-num> | timeout <timeout> | retry-down-count<count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
PLB probeprobe
Service modeprobe-id-dns
Host name/Target addresshost
DNS Target IP Address or Hostnamehost-name
(Optional) Frequency in secondsfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeout in secondstimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
(Optional) ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/plb-dg-node
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3516
P Commandsprobe host
Page 3661
probe host[no] probe <probe-id-dns> host <host-name> [ frequency <freq-num> | timeout <timeout> | retry-down-count<count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure probe for nodeprobe
Service modeprobe-id-dns
Host name/Target addresshost
DNS Target IP Address or Hostnamehost-name
(Optional) Configure probe frequency for a nodefrequency
(Optional) Frequency in secondsfreq-num
(Optional) Configure probe timeout for a nodetimeout
(Optional) Timeout in secondstimeout
(Optional) Configure retry-count before node declared downretry-down-count
(Optional) Countcount
(Optional) Configure retry-count after node declared downretry-up-count
(Optional) Countup-count
(Optional) Configure ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/plb-dg-node-standby
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3517
P Commandsprobe host
Page 3662
probe host[no] probe <probe-id-dns> host <host-name> [ frequency <freq-num> | timeout <timeout> | retry-down-count<count> | retry-up-count <up-count> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
PLB probeprobe
Service modeprobe-id-dns
Host name/Target addresshost
DNS Target IP Address or Hostnamehost-name
(Optional) Frequency in secondsfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeout in secondstimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
Command Mode
• /exec/configure/plb-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3518
P Commandsprobe host
Page 3663
probe port[no] probe <probe-id> port <port-num> [ control <status> ] [ frequency <freq-num> | timeout <timeout> |retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure probe for nodeprobe
Service modeprobe-id
TCP/UDP Portport
Port numberport-num
(Optional) control protocolcontrol
(Optional) control protocol statusstatus
(Optional) Configure probe frequency for a nodefrequency
(Optional) Frequency in secondsfreq-num
(Optional) Configure probe timeout for a nodetimeout
(Optional) Timeout in secondstimeout
(Optional) Configure retry-count before node declared downretry-down-count
(Optional) Countcount
(Optional) Configure retry-count after node declared upretry-up-count
(Optional) Countup-count
(Optional) Configure ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/plb-dg-node-standby
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3519
P Commandsprobe port
Page 3664
probe port{ probe <probe-id> port <port-num> [ control <status> ] [ frequency <freq-num> | timeout <timeout> |retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] + } | { no probe }
Syntax Description
Negate a command or set its defaultsno
Catena probeprobe
Service modeprobe-id
Portport
Port numberport-num
(Optional) control protocolcontrol
(Optional) control protocol statusstatus
(Optional) Frequency in secondsfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeout in secondstimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
(Optional) ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/catena-device-grp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3520
P Commandsprobe port
Page 3665
probe port[no] probe <probe-id> port <port-num> [ control <status> ] [ frequency <freq-num> | timeout <timeout> |retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD probeprobe
Service modeprobe-id
Portport
Port numberport-num
(Optional) control protocolcontrol
(Optional) control protocol statusstatus
(Optional) Frequency in secondsfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeout in secondstimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
(Optional) ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/itd-dg-node
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3521
P Commandsprobe port
Page 3666
probe port[no] probe <probe-id> port <port-num> [ control <status> ] [ frequency <freq-num> | timeout <timeout> |retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD probeprobe
Service modeprobe-id
Portport
Port numberport-num
(Optional) control protocolcontrol
(Optional) control protocol statusstatus
(Optional) Frequency in secondsfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeout in secondstimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
(Optional) ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/itd-dg-node-standby
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3522
P Commandsprobe port
Page 3667
probe port[no] probe <probe-id> port <port-num> [ control <status> ] [ frequency <freq-num> | timeout <timeout> |retry-down-count <count> | retry-up-count <up-count> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD probeprobe
Service modeprobe-id
Portport
Port numberport-num
(Optional) control protocolcontrol
(Optional) control protocol statusstatus
(Optional) Frequency in secondsfrequency
(Optional) Frequency in secondsfreq-num
(Optional) Timeout in secondstimeout
(Optional) Timeout in secondstimeout
(Optional) Retry-count when node goes downretry-down-count
(Optional) Countcount
(Optional) Retry-count when node comes back upretry-up-count
(Optional) Countup-count
Command Mode
• /exec/configure/itd-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3523
P Commandsprobe port
Page 3668
probe port[no] probe <probe-id> port <port-num> [ control <status> ] [ frequency <freq-num> | timeout <timeout> |retry-down-count <count> | retry-up-count <up-count> | ip <ip-addr> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure probe for PLB device group nodeprobe
Service modeprobe-id
TCP/UDP Portport
Port numberport-num
(Optional) control protocolcontrol
(Optional) control protocol statusstatus
(Optional) Configure probe frequency for a nodefrequency
(Optional) Frequency in secondsfreq-num
(Optional) Configure probe timeout for a nodetimeout
(Optional) Timeout in secondstimeout
(Optional) Configure retry-count before node declared downretry-down-count
(Optional) Countcount
(Optional) Configure retry-count after node declared upretry-up-count
(Optional) Countup-count
(Optional) Configure ip address for probeip
(Optional) IP4 prefix in format i.i.i.iip-addr
Command Mode
• /exec/configure/plb-dg-node
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3524
P Commandsprobe port
Page 3669
probe port[no] probe <probe-id> port <port-num> [ control <status> ] [ frequency <freq-num> | timeout <timeout> |retry-down-count <count> | retry-up-count <up-count> ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure probe for nodeprobe
Service modeprobe-id
Portport
TCP/UDP Port numberport-num
(Optional) control protocolcontrol
(Optional) control protocol statusstatus
(Optional) Configure probe frequency for a nodefrequency
(Optional) Frequency in secondsfreq-num
(Optional) Configure probe timeout for a nodetimeout
(Optional) Timeout in secondstimeout
(Optional) Configure retry-count before node declared downretry-down-count
(Optional) Countcount
(Optional) Configure retry-count after node declared upretry-up-count
(Optional) Countup-count
Command Mode
• /exec/configure/plb-device-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3525
P Commandsprobe port
Page 3670
profile{ profile <pid> | no profile }
Syntax Description
Negate a command or set its defaultsno
NGOAM profile to useprofile
NGOAM profile idpid
Command Mode
• /exec/configure/configngoamconnectcheck
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3526
P Commandsprofile
Page 3671
profile[no] profile <profile-name>
Syntax Description
(Optional) Negate the commandno
Packet Drop Profileprofile
Profile nameprofile-name
Command Mode
• /exec/configure/pkt-drop
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3527
P Commandsprofile
Page 3672
promiscuous-mode offpromiscuous-mode { off | on } | no promiscuous-mode [ { off | on } ]
Syntax Description
Negate a command or set its defaultsno
Configure promiscuous mode for the portpromiscuous-mode
Disable promiscuous modeoff
Enable promiscuous modeon
Command Mode
• /exec/configure/if-port-channel /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3528
P Commandspromiscuous-mode off
Page 3673
propagate-sgt[no] propagate-sgt
Syntax Description
Enable SGT propagation from this port (the default use the no form todisable)
propagate-sgt
Command Mode
• /exec/configure/cts-dot1x /exec/configure/cts-manual
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3529
P Commandspropagate-sgt
Page 3674
protection[no] protection | protection [ fast-reroute [ bw-protect ] ]
Syntax Description
Negate a command or set its defaultsno
Enable failure protectionprotection
(Optional) Enable fast-reroute failure protectionfast-reroute
(Optional) Enable BW protectionbw-protect
Command Mode
• /exec/configure/te/lsp-attr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3530
P Commandsprotection
Page 3675
proto{ proto <proto-id> }
Syntax Description
Protocolproto
IANA Protocol idproto-id
Command Mode
• /exec/configure/configngoamccpayload
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3531
P Commandsproto
Page 3676
protocol-versionprotocol-version { <10> | <13> | negotiate } | no protocol-version
Syntax Description
Negate a command or set its defaultsno
Set OpenFlow protocol versionprotocol-version
Use only OF 1.0 protocol to connect to controller10
Use only OF 1.3 protocol to connect to controller13
Negotiate protocol with controllernegotiate
Command Mode
• /exec/configure/openflow/switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3532
P Commandsprotocol-version
Page 3677
protocol-versionprotocol-version { <10> | <13> | negotiate } | no protocol-version
Syntax Description
Negate a command or set its defaultsno
Set OpenFlow protocol versionprotocol-version
Use only OF 1.0 protocol to connect to controller10
Use only OF 1.3 protocol to connect to controller13
Negotiate protocol with controllernegotiate
Command Mode
• /exec/configure/openflow/switch/sub-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3533
P Commandsprotocol-version
Page 3678
protocol{ protocol <num> } | { no protocol }
Syntax Description
Negate a command or set its defaultsno
specify flow protocol numberprotocol
flow protocol numbernum
Command Mode
• /exec/configure/configngoamprofileflow
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3534
P Commandsprotocol
Page 3679
protocol[no] protocol <proto> [ prefix-list <pflist-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
proto
(Optional) Name of the prefix-list to be matchedpflist-name
Command Mode
• /exec/configure/config-snoop-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3535
P Commandsprotocol
Page 3680
protocol shutdown[no] protocol shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
OSPF protocolprotocol
shutdown the OSPF protocol instanceshutdown
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3536
P Commandsprotocol shutdown
Page 3681
protocol shutdown[no] protocol shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
OSPF protocolprotocol
Shutdown the OSPF protocol instanceshutdown
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3537
P Commandsprotocol shutdown
Page 3682
ptp[no] ptp
Syntax Description
(Optional) Negate a command or set its defaultsno
Precision Time Protocol (IEEE 1588) Subsystemptp
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3538
P Commandsptp
Page 3683
ptp announce interval[no] ptp announce interval { <log-seconds> | smpte-2059-2 <smpte-log-seconds> | aes67 <aes-log-seconds>}
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
announceannounce
intervalinterval
log secondslog-seconds
SMPTE-2059-2smpte-2059-2
SMPTE-2059-2 log secondssmpte-log-seconds
AES67-2015aes67
AES67-2015 log secondsaes-log-seconds
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3539
P Commandsptp announce interval
Page 3684
ptp announce timeout[no] ptp announce timeout { <val> | smpte-2059-2 <smpte-val> | aes67 <aes-val> }
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
announceannounce
timeouttimeout
SMPTE-2059-2smpte-2059-2
AES67-2015aes67
val
SMPTE-2059-2 valsmpte-val
AES67-2015 valaes-val
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3540
P Commandsptp announce timeout
Page 3685
ptp clock-identityptp clock-identity <mac-address> | no ptp clock-identity
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
clock-identityclock-identity
Mac Addressmac-address
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3541
P Commandsptp clock-identity
Page 3686
ptp clock-sync auto[no] ptp clock-sync auto
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
clock-syncclock-sync
auto adjust frequencyauto
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3542
P Commandsptp clock-sync auto
Page 3687
ptp clock one-step[no] ptp { clock-mode | clock-operation } one-step
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
Set the PTP Clock modeclock-mode
Set the PTP Clock Operationclock-operation
One stepone-step
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3543
P Commandsptp clock one-step
Page 3688
ptp convergence-time[no] ptp convergence-time [ <val> ]
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
Convergence time for Grandmaster capable node, default 10 secondsconvergence-time
(Optional) convergence-timeval
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3544
P Commandsptp convergence-time
Page 3689
ptp correction-range[no] ptp correction-range <threshold-value>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
set correction range threshold valuecorrection-range
correction threshold (ns) [-value, +value], default 100000 (100 us)threshold-value
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3545
P Commandsptp correction-range
Page 3690
ptp correction-range logging[no] ptp correction-range logging
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
set correction range threshold valuecorrection-range
enable logging for corrections exceeding threshold valuelogging
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3546
P Commandsptp correction-range logging
Page 3691
ptp correction hardware[no] ptp correction hardware
Syntax Description
(Optional) Negate a command or set its defaultsno
Precision Time Protocol (IEEE 1588) Subsystemptp
Corrections for PTPcorrection
Frequency correction from hardware or softwarehardware
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3547
P Commandsptp correction hardware
Page 3692
ptp cost[no] ptp cost <cost>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
Cost associated with the interfacecost
Costcost
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3548
P Commandsptp cost
Page 3693
ptp delay-request minimum interval[no] ptp delay-request minimum interval { <log-seconds> | smpte-2059-2 <smpte-log-seconds> | aes67<aes-log-seconds> }
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
delay-requestdelay-request
minimumminimum
intervalinterval
SMPTE-2059-2smpte-2059-2
AES67-2015aes67
log secondslog-seconds
SMPTE-2059-2 log secondssmpte-log-seconds
AES67-2015 log secondsaes-log-seconds
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3549
P Commandsptp delay-request minimum interval
Page 3694
ptp device-type boundary[no] ptp device-type { boundary-clock | generalized-ptp }
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
ptp device-typedevice-type
boundary-clockboundary-clock
Generalized PTPgeneralized-ptp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3550
P Commandsptp device-type boundary
Page 3695
ptp domain[no] ptp domain <domain-val>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
ptp domain to be associated with interfacedomain
Enter configured domain value, default 0domain-val
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3551
P Commandsptp domain
Page 3696
ptp domain[no] ptp domain <domain-val>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
ptp clock domaindomain
Enter domain valuedomain-val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3552
P Commandsptp domain
Page 3697
ptp domain clock-accuracy-threshold[no] ptp domain <domain-val> clock-accuracy-threshold <threshold-value>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
ptp clock domaindomain
Domain value, default is 0domain-val
Domain clock accuracy thresholdclock-accuracy-threshold
Domain clock accuracy threshold value, default is 254threshold-value
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3553
P Commandsptp domain clock-accuracy-threshold
Page 3698
ptp domain clock-class-threshold[no] ptp domain <domain-val> clock-class-threshold <threshold-value>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
ptp clock domaindomain
Domain value, default is 0domain-val
Domain clock class thresholdclock-class-threshold
Domain clock class threshold value, default is 248threshold-value
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3554
P Commandsptp domain clock-class-threshold
Page 3699
ptp domain priority[no] ptp domain <domain-val> priority <priority-val>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
ptp clock domaindomain
Domain value, default is 0domain-val
Domain prioritypriority
Domain priority value, default is 255priority-val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3555
P Commandsptp domain priority
Page 3700
ptp grandmaster-capableptp grandmaster-capable | no ptp grandmaster-capable [ convergence-time <val> ]
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
Grandmaster capabilitygrandmaster-capable
(Optional) Convergence time in secondsconvergence-time
(Optional) convergenceval
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3556
P Commandsptp grandmaster-capable
Page 3701
ptp mean-path-delay[no] ptp mean-path-delay <threshold-value>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
set mean-path-delay threshold valuemean-path-delay
mean-path-delay threshold (ns), default 1000000000 (1 sec)threshold-value
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3557
P Commandsptp mean-path-delay
Page 3702
ptp multi-domainptp multi-domain | no ptp multi-domain
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
Configure ptp multi-domainmulti-domain
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3558
P Commandsptp multi-domain
Page 3703
ptp multi-domain transition-attributes priority1[no] ptp multi-domain transition-attributes priority1 <priority1-value>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
Configure ptp multi-domainmulti-domain
ptp multi-domain priority domain conversion attributestransition-attributes
domain conversion priority1 valuepriority1
Enter domain priority1 value, default 255priority1-value
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3559
P Commandsptp multi-domain transition-attributes priority1
Page 3704
ptp multi-domain transition-attributes priority2[no] ptp multi-domain transition-attributes priority2 <priority2-value>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
Configure ptp multi-domainmulti-domain
ptp multi-domain priority domain conversion attributestransition-attributes
domain conversion priority2 valuepriority2
Enter domain priority2 value, default 255priority2-value
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3560
P Commandsptp multi-domain transition-attributes priority2
Page 3705
ptp multicast master-only[no] ptp multicast master-only
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
multicastmulticast
master onlymaster-only
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3561
P Commandsptp multicast master-only
Page 3706
ptp neighbor propagation-delay-threshold[no] ptp neighbor propagation-delay-threshold <nseconds>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
ptp neighborneighbor
GPTP propagation delay thresholdpropagation-delay-threshold
Interval in nano-secondsnseconds
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3562
P Commandsptp neighbor propagation-delay-threshold
Page 3707
ptp offload[no] ptp offload
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
Allows increasing number of PTP sessions per system by offloadingsome timers to linecard
offload
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3563
P Commandsptp offload
Page 3708
ptp pdelay-req-interval[no] ptp pdelay-req-interval <val>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
Log mean peer delay request intervalpdelay-req-interval
valueval
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3564
P Commandsptp pdelay-req-interval
Page 3709
ptp priority1[no] ptp priority1 <val>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
priority1priority1
priority1val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3565
P Commandsptp priority1
Page 3710
ptp priority2[no] ptp priority2 <val>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
priority1priority2
priority2val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3566
P Commandsptp priority2
Page 3711
ptp source[no] ptp source <src-ip> [ vrf { <vrf-name> | <vrf-cfg-name> } ]
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
source IP addresssource
IPv4 address (A.B.C.D) of sourcesrc-ip
(Optional) vrf to be used for hello messagesvrf
(Optional) vrf to be used for hellosvrf-name
(Optional) Configurable VRF namevrf-cfg-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3567
P Commandsptp source
Page 3712
ptp sync interval[no] ptp sync interval { <log-seconds> | smpte-2059-2 <smpte-log-seconds> | aes67 <aes-log-seconds> }
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
syncsync
intervalinterval
SMPTE-2059-2smpte-2059-2
AES67-2015aes67
log secondslog-seconds
SMPTE-2059-2 log secondssmpte-log-seconds
AES67-2015 log secondsaes-log-seconds
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3568
P Commandsptp sync interval
Page 3713
ptp transport ipv4 ucast master[no] ptp transport ipv4 ucast master
Syntax Description
(Optional) Negate a command or set its defaultsno
Precision Time Protocol (IEEE 1588) Subsystemptp
unicast supporttransport
ipv4ipv4
ipv4 unicastucast
master modemaster
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3569
P Commandsptp transport ipv4 ucast master
Page 3714
ptp transport ipv4 ucast slave[no] ptp transport ipv4 ucast slave
Syntax Description
(Optional) Negate a command or set its defaultsno
Precision Time Protocol (IEEE 1588) Subsystemptp
unicast supporttransport
ipv4ipv4
ipv4 unicastucast
slave modeslave
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3570
P Commandsptp transport ipv4 ucast slave
Page 3715
ptp ucast-source[no] ptp ucast-source <src-ip> [ vrf { <vrf-name> | <vrf-cfg-name> } ]
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
source IP address for ucast messagesucast-source
IPv4 address (A.B.C.D) of sourcesrc-ip
(Optional) vrf to be used for hello messagesvrf
(Optional) vrf to be used for hellosvrf-name
(Optional) Configurable VRF namevrf-cfg-name
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3571
P Commandsptp ucast-source
Page 3716
ptp vlan[no] ptp vlan <vlan>
Syntax Description
Precision Time Protocol (IEEE 1588) Subsystemptp
vlanvlan
vlanvlan
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3572
P Commandsptp vlan
Page 3717
purge module running-configpurge module <module> running-config
Syntax Description
Deletes unused datapurge
Purge configuration for non-existent modulesmodule
Enter module numbermodule
purge running configuration for non-existent modulesrunning-config
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3573
P Commandspurge module running-config
Page 3718
pushpush [ <name> ]
Syntax Description
push current mode to stack or save it under namepush
(Optional) namename
Command Mode
• /global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3574
P Commandspush
Page 3719
pwdpwd
Syntax Description
View current directorypwd
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3575
P Commandspwd
Page 3720
pythonpython [ <uri> [ <pyargs> ] + ]
Syntax Description
run a python command/script, or enter python mode (if no arg)python
(Optional) path to a python fileuri
(Optional) python command line arguments (maximum 32)pyargs
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3576
P Commandspython
Page 3721
python instance[no] python instance <inst> [ <uri> [ <pyargs> ] + ] | python instance <inst> <uri> [ <pyargs> ] +
Syntax Description
Negate a command or set its defaultsno
run a python command/script, or enter python mode (if no arg)python
label with an instance numberinstance
instance numberinst
(Optional) path to a python fileuri
(Optional) python command line arguments (maximum 32)pyargs
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3577
P Commandspython instance
Page 3722
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3578
P Commandspython instance
Page 3723
Q Commands
• qos copy policy-map type network-qos prefix, on page 3580• qos copy policy-map type queuing prefix, on page 3581• qos qos-policies statistics, on page 3582• qos shared-policer, on page 3583• qos statistics, on page 3587• qualify udf, on page 3588• queue-limit, on page 3589• queue-limit2, on page 3590• queue-limit3, on page 3591• queue-limit4, on page 3592• queue-limit5, on page 3593• queue-limit bytes, on page 3594
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3579
Page 3724
qos copy policy-map type network-qos prefixqos copy policy-map type network-qos <pmap-nq-enum-name-dc3> { prefix | suffix } <ix-name>
Syntax Description
Copy (Clone) templatecopy
Configure a policy mappolicy-map
Specify the type of this policy-maptype
Network QoS policynetwork-qos
pmap-nq-enum-name-dc3
Policy map name prefixprefix
Policy map name suffixsuffix
Suffix/Prefix name, max size counted together with policy nameix-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3580
Q Commandsqos copy policy-map type network-qos prefix
Page 3725
qos copy policy-map type queuing prefixqos copy policy-map type queuing <pmap-name-que-temp> { prefix | suffix } <ix-name>
Syntax Description
Copy (Clone) templatecopy
Configure a policy mappolicy-map
Specify the type of this policy-maptype
Queuing policyqueuing
Policy-map namepmap-name-que-temp
Policy map name prefixprefix
Policy map name suffixsuffix
Suffix/Prefix name, max size counted together with policy nameix-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3581
Q Commandsqos copy policy-map type queuing prefix
Page 3726
qos qos-policies statistics[no] qos qos-policies statistics
Syntax Description
(Optional) Negate a command or set its defaultsno
All qos type policiesqos-policies
statisticsstatistics
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3582
Q Commandsqos qos-policies statistics
Page 3727
qos shared-policer{ qos shared-policer [ type qos ] <policer-name> { [ cir ] { <cir-val> [ bps | kbps | mbps | gbps | pps ] | percent<cir-perc> } [ [ bc ] { <committed-burst> [ bytes | kbytes | mbytes | ms | us | packets ] } ] [ pir { <pir-val> [bps2 | kbps2 | mbps2 | gbps2 | pps2 ] | percent <pir-perc> } [ [ be ] { <extended-burst> [ bytes2 | kbytes2 |mbytes2 | ms2 | us2 | packets2 ] } ] ] [ conform { transmit | set-prec-transmit { <prec-val> | <prec-enum> } |set-dscp-transmit { <dscp-val> | <dscp-enum> } | set-cos-transmit <cos-val> | set-discard-class-transmit<disc-class-val> | set-qos-transmit <qos-grp-val> | set-mpls-exp-imposition-transmit <exp-value-imp> |set-mpls-exp-topmost-transmit <exp-value-top> } ] [ exceed { transmit1 | drop1 | set <exc-frm-field><exc-to-field> table cir-markdown-map | set-prec-transmit1 { <prec-val1> | <prec-enum1> } | set-dscp-transmit1{ <dscp-val1> | <dscp-enum1> } | set-cos-transmit1 <cos-val1> | set-discard-class-transmit1 <disc-class-val1>| set-qos-transmit1 <qos-grp-val1> | set-mpls-exp-imposition-transmit1 <exp-value-imp1> |set-mpls-exp-topmost-transmit1 <exp-value-top1> } ] [ violate { drop2 | set <vio-frm-field> <vio-to-field>table2 pir-markdown-map | set-prec-transmit2 { <prec-val2> | <prec-enum2> } | set-dscp-transmit2 {<dscp-val2> | <dscp-enum2> } | set-cos-transmit2 <cos-val2> | set-discard-class-transmit2 <disc-class-val2>| set-qos-transmit2 <qos-grp-val2> | set-mpls-exp-imposition-transmit2 <exp-value-imp2> |set-mpls-exp-topmost-transmit2 <exp-value-top2> } ] } | no qos shared-policer [ type qos ] <policer-name>}
Syntax Description
Negate a command or set its defaultsno
Shared policershared-policer
Shared policer namepolicer-name
(Optional) Specify the type of shared-policertype
QoS Global Commandsqos
(Optional) Specify committed information ratecir
(Optional) Specify committed burstbc
Specify rate as percentage of interface data-ratepercent
Percentagecir-perc
(Optional) Percentagepir-perc
(Optional) Specify peak information ratepir
(Optional) Specify extended burst (for 1R3C meter)be
(Optional) Bits per secondbps
(Optional) Kilo bits per secondkbps
(Optional) Mega bits per secondmbps
(Optional) Giga bits per secondgbps
(Optional) Packets per secondpps
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3583
Q Commandsqos shared-policer
Page 3728
(Optional) Bits per secondbps2
(Optional) Kilo Bits per secondkbps2
(Optional) Mega Bits per secondmbps2
(Optional) Giga Bits per secondgbps2
(Optional) Packets per secondpps2
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Micro second(s)us
(Optional) Milli second(s)ms
(Optional) Packetspackets
(Optional) Bytesbytes2
(Optional) Kilo Byteskbytes2
(Optional) Mega Bytesmbytes2
(Optional) Milli secondsms2
(Optional) Micro secondsus2
(Optional) Packetspackets2
(Optional) Specify a conform actionconform
(Optional) Specify a exceed actionexceed
(Optional) Specify a violate actionviolate
(Optional) Transmit packettransmit
(Optional) Transmit packettransmit1
(Optional) Drop packetdrop1
(Optional) Drop packetdrop2
(Optional) Set precedence and send itset-prec-transmit
(Optional) Set precedence and send itset-prec-transmit1
(Optional) Set precedence and send itset-prec-transmit2
(Optional) Precedence valueprec-val
(Optional) Precedence valueprec-val1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3584
Q Commandsqos shared-policer
Page 3729
(Optional) Precedence valueprec-val2
(Optional)prec-enum
(Optional)prec-enum1
(Optional)prec-enum2
(Optional) Set dscp and send itset-dscp-transmit
(Optional) Set dscp and send itset-dscp-transmit1
(Optional) Set dscp and send itset-dscp-transmit2
(Optional) DSCP valuedscp-val
(Optional) DSCP valuedscp-val1
(Optional) DSCP valuedscp-val2
(Optional)dscp-enum
(Optional)dscp-enum1
(Optional)dscp-enum2
(Optional) Set cos and send itset-cos-transmit
(Optional) Set cos and send itset-cos-transmit1
(Optional) Set cos and send itset-cos-transmit2
(Optional) new cos valuecos-val
(Optional) new cos valuecos-val1
(Optional) new cos valuecos-val2
(Optional) Set discard class and send itset-discard-class-transmit
(Optional) Set discard class and send itset-discard-class-transmit1
(Optional) Set discard class and send itset-discard-class-transmit2
(Optional) new discard-class valuedisc-class-val
(Optional) new discard-class valuedisc-class-val1
(Optional) new discard-class valuedisc-class-val2
(Optional) Set qos-group and send itset-qos-transmit
(Optional) Set qos-group and send itset-qos-transmit1
(Optional) Set qos-group and send itset-qos-transmit2
(Optional) QoS group valueqos-grp-val
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3585
Q Commandsqos shared-policer
Page 3730
(Optional) QoS group valueqos-grp-val1
(Optional) QoS group valueqos-grp-val2
(Optional) set-mpls-exp-imposition-transmitset-mpls-exp-imposition-transmit
(Optional) set-mpls-exp-imposition-transmitset-mpls-exp-imposition-transmit1
(Optional) set-mpls-exp-imposition-transmitset-mpls-exp-imposition-transmit2
(Optional) MPLS imposition valueexp-value-imp
(Optional) MPLS imposition valueexp-value-imp1
(Optional) MPLS imposition valueexp-value-imp2
(Optional) Set MPLS topmost labelset-mpls-exp-topmost-transmit
(Optional) Set MPLS topmost labelset-mpls-exp-topmost-transmit1
(Optional) Set MPLS topmost labelset-mpls-exp-topmost-transmit2
(Optional) MPLS topmost valueexp-value-top
(Optional) MPLS topmost valueexp-value-top1
(Optional) MPLS topmost valueexp-value-top2
(Optional) Set a particular value using table or markdown mapset
(Optional)exc-frm-field
(Optional)exc-to-field
(Optional)vio-frm-field
(Optional)vio-to-field
(Optional) Set using the table-maptable
(Optional) Set using the table-maptable2
(Optional) Markdown map table name for exceed actioncir-markdown-map
(Optional) Markdown map table name for violate actionpir-markdown-map
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3586
Q Commandsqos shared-policer
Page 3731
qos statistics[no] qos statistics
Syntax Description
(Optional) Negate a command or set its defaultsno
statisticsstatistics
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3587
Q Commandsqos statistics
Page 3732
qualify udf[no] <udf_tcam_type> qualify udf { <udf_name> } +
Syntax Description
(Optional) Negate a command or set its defaultsno
Region typeudf_tcam_type
Configure UDFs to be qualified for span regionqualify
Configure UDF namesudf
UDF nameudf_name
Command Mode
• /exec/configure/tcam-templ
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3588
Q Commandsqualify udf
Page 3733
queue-limit[no] queue-limit [ cos <cos-val> ] { <q-size> [ packets | bytes | kbytes | mbytes | ms | us ] | percent <perc-q-size>| dynamic <alpha> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure queue size for the classqueue-limit
(Optional) IEEE 802.1Q Class of Servicecos
(Optional) 802.1Q Class of Service valuecos-val
Specify queue size in Percentagepercent
Queue size in percentage of total tx/rx buffer sizeperc-q-size
Queue size in dynamic alpha factordynamic
0-1/128, 1-1/64, 2-1/32, 3-1/16, 4-1/8, 5-1/4, 6-1/2, 7-1, 8-2, 9-4, 10-8alpha
(Optional) Packetspackets
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Milli second(s)ms
(Optional) Micro second(s)us
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3589
Q Commandsqueue-limit
Page 3734
queue-limit2[no] queue-limit2 [ cos2 <cos-val> ] { <q-size> [ packets | bytes | kbytes | mbytes | ms | us ] | percent2<perc-q-size> | dynamic2 <alpha> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure queue size for the classqueue-limit2
(Optional) IEEE 802.1Q Class of Servicecos2
(Optional) 802.1Q Class of Service valuecos-val
Specify queue size in Percentagepercent2
Queue size in percentage of total tx/rx buffer sizeperc-q-size
Queue size in dynamic alpha factordynamic2
0-1/128, 1-1/64, 2-1/32, 3-1/16, 4-1/8, 5-1/4, 6-1/2, 7-1, 8-2, 9-4, 10-8alpha
(Optional) Packetspackets
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Milli second(s)ms
(Optional) Micro second(s)us
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3590
Q Commandsqueue-limit2
Page 3735
queue-limit3[no] queue-limit3 [ cos3 <cos-val> ] { <q-size> [ packets | bytes | kbytes | mbytes | ms | us ] | percent3<perc-q-size> | dynamic3 <alpha> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure queue size for the classqueue-limit3
(Optional) IEEE 802.1Q Class of Servicecos3
(Optional) 802.1Q Class of Service valuecos-val
Specify queue size in Percentagepercent3
Queue size in percentage of total tx/rx buffer sizeperc-q-size
Queue size in dynamic alpha factordynamic3
0-1/8, 1-1/4, 2-1/2, 3-3/4, 4-9/8, 5-15/8, 6-3, 7-5, 8-8, 9-14, 10-18alpha
(Optional) Packetspackets
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Milli second(s)ms
(Optional) Micro second(s)us
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3591
Q Commandsqueue-limit3
Page 3736
queue-limit4[no] queue-limit4 [ cos4 <cos-val> ] { <q-size> [ packets | bytes | kbytes | mbytes | ms | us ] | percent4<perc-q-size> | dynamic4 <alpha> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure queue size for the classqueue-limit4
(Optional) IEEE 802.1Q Class of Servicecos4
(Optional) 802.1Q Class of Service valuecos-val
Specify queue size in Percentagepercent4
Queue size in percentage of total tx/rx buffer sizeperc-q-size
Queue size in dynamic alpha factordynamic4
0-3/2, 1-3, 2-6, 3-11, 4-20, 5-33, 6-50, 7-66, 8-80alpha
(Optional) Packetspackets
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Milli second(s)ms
(Optional) Micro second(s)us
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3592
Q Commandsqueue-limit4
Page 3737
queue-limit5[no] queue-limit5 [ cos5 <cos-val> ] { <q-size> [ packets | bytes | kbytes | mbytes | ms | us ] | percent5<perc-q-size> | dynamic5 <alpha> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure queue size for the classqueue-limit5
(Optional) IEEE 802.1Q Class of Servicecos5
(Optional) 802.1Q Class of Service valuecos-val
Specify queue size in Percentagepercent5
Queue size in percentage of total tx/rx buffer sizeperc-q-size
Queue size in dynamic alpha factordynamic5
1-1/16, 2-1/8, 3-1/4, 4-1/2, 5-1, 6-2, 7-4, 8-8alpha
(Optional) Packetspackets
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Milli second(s)ms
(Optional) Micro second(s)us
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3593
Q Commandsqueue-limit5
Page 3738
queue-limit bytes[no] queue-limit { <q-size> bytes }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure queue size for the classqueue-limit
Bytesbytes
Command Mode
• /exec/configure/policy-map/type/uf/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3594
Q Commandsqueue-limit bytes
Page 3739
R Commands
• radius-server deadtime, on page 3600• radius-server directed-request, on page 3601• radius-server host key 0 6 7, on page 3602• radius-server host test, on page 3604• radius-server key 0 6 7, on page 3605• radius-server pss-clean, on page 3606• radius-server retransmit, on page 3607• radius-server test, on page 3608• radius-server timeout, on page 3609• random-detect, on page 3610• random-detect2 minimum-threshold2 maximum-threshold2, on page 3612• random-detect2 non-ecn minimum-threshold2 maximum-threshold2 drop, on page 3613• random-detect, on page 3614• random-detect cos-based, on page 3616• rate-limit, on page 3618• rate-limit cpu direction pps action log, on page 3619• rate-limit cpu direction pps action log, on page 3620• rate-limit packet_in burst, on page 3621• rate-limit packet_in burst, on page 3622• rate-mode, on page 3623• rd auto, on page 3624• rd auto, on page 3625• receiver, on page 3626• reconnect-interval, on page 3627• record-route, on page 3628• record-route, on page 3629• record, on page 3630• record, on page 3631• record, on page 3632• record, on page 3633• record, on page 3634• redistribute bgp, on page 3635• redistribute bgp eigrp isis ospf rip static direct amt lisp route-map, on page 3636
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3595
Page 3740
• redistribute filter route-map, on page 3637• redistribute filter route-map, on page 3638• redistribute maximum-prefix, on page 3639• redistribute maximum-prefix, on page 3640• redistribute maximum-prefix, on page 3641• redistribute maximum-prefix, on page 3642• redistribute maximum-prefix, on page 3643• redistribute route-map, on page 3644• redistribute route-map, on page 3645• redistribute route-map, on page 3646• redistribute route-map, on page 3647• redistribute route-map, on page 3648• redistribute route-map, on page 3649• redistribute route-map, on page 3650• redistribute route-map, on page 3651• redistribute route-map, on page 3652• redistribute route-map, on page 3653• redownload forwarding state, on page 3654• redundancy-group, on page 3655• reference-bandwidth, on page 3656• reference-bandwidth, on page 3657• register-database-mapping, on page 3658• register-route-notifications, on page 3659• reload, on page 3660• reload cancel, on page 3661• reload in, on page 3662• reload module, on page 3663• reload module force-dnld, on page 3664• reload non-interruptive, on page 3665• reload power-cycle, on page 3666• reload sync-adjacency, on page 3667• reload sync-adjacency, on page 3668• reload timer, on page 3669• reload vdc, on page 3670• reload vdc, on page 3671• remark, on page 3672• remark, on page 3673• remark, on page 3674• remote-as, on page 3675• remote-span, on page 3676• remote, on page 3677• remove-private-as, on page 3678• reoptimize events link-up, on page 3679• replay-protection, on page 3680• report, on page 3681• report, on page 3682
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3596
R Commands
Page 3741
• report, on page 3683• report, on page 3684• report, on page 3685• report, on page 3686• report, on page 3687• report, on page 3688• report, on page 3689• report, on page 3690• report, on page 3691• report, on page 3692• report, on page 3693• report, on page 3694• report, on page 3695• report, on page 3696• request-data-size, on page 3697• request-data-size, on page 3698• request-data-size, on page 3699• resequence access, on page 3700• reset, on page 3701• reset, on page 3702• reset, on page 3703• reset, on page 3704• reset, on page 3705• reset, on page 3706• reset, on page 3707• reset, on page 3708• reset, on page 3709• reset, on page 3710• reset, on page 3711• reset, on page 3712• reset, on page 3713• reset, on page 3714• reset, on page 3715• reset, on page 3716• restart amt, on page 3717• restart bgp, on page 3718• restart eigrp, on page 3719• restart igmp, on page 3720• restart isis, on page 3721• restart msdp, on page 3722• restart ospf, on page 3723• restart ospfv3, on page 3724• restart pim, on page 3725• restart pim6, on page 3726• restart rip, on page 3727• restart rsvp, on page 3728
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3597
R Commands
Page 3742
• resync-database, on page 3729• retain route-target all, on page 3730• retain route-target all, on page 3731• retransmit-interval, on page 3732• retransmit-interval, on page 3733• retransmit-interval, on page 3734• revision, on page 3735• revocation-check crl, on page 3736• rewrite-evpn-rt-asn, on page 3737• rewrite-rt-asn, on page 3738• rfc1583compatibility, on page 3739• rip shutdown, on page 3740• rmdir, on page 3741• rmon alarm absolute rising-threshold falling-threshold, on page 3742• rmon event, on page 3743• rmon hcalarm absolute startupalarm rising-threshold falling-threshold owner, on page 3744• roaming-eid-prefix, on page 3745• role feature-group name, on page 3746• role name, on page 3747• role priority, on page 3748• rollback running-config checkpoint, on page 3749• root-priority, on page 3750• route-map, on page 3751• route-map, on page 3752• route-map, on page 3753• route-map, on page 3754• route-map out, on page 3755• route-map pbr-statistics, on page 3756• route-reflector-client, on page 3757• route-reflector-client, on page 3758• route-target both auto, on page 3759• route-target both auto, on page 3760• route-target export, on page 3761• route-target export auto, on page 3762• route-target import, on page 3763• route-target import auto, on page 3764• route delete dampen interval, on page 3765• router-guard ip multicast, on page 3766• router-guard ip multicast switchports, on page 3767• router-id, on page 3768• router-id, on page 3769• router-id, on page 3770• router-id, on page 3771• router-id, on page 3772• router-id, on page 3773• router-preference maximum, on page 3774
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3598
R Commands
Page 3743
• router bgp, on page 3775• router eigrp, on page 3776• router isis, on page 3777• router ospf, on page 3778• router ospfv3, on page 3779• router rip, on page 3780• routing-context vrf, on page 3781• rsakeypair, on page 3782• rtr etr eid, on page 3783• rule, on page 3784• rule command, on page 3785• rule oid, on page 3786• run-script, on page 3787• run2 guestshell, on page 3788• run bash, on page 3789
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3599
R Commands
Page 3744
radius-server deadtime[no] radius-server deadtime <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
duration for which non-reachable server is skippeddeadtime
Length of time, in minutesi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3600
R Commandsradius-server deadtime
Page 3745
radius-server directed-request[no] radius-server directed-request
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
enable direct authentication requests to serverdirected-request
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3601
R Commandsradius-server directed-request
Page 3746
radius-server host key 0 6 7{ { [ no ] radius-server host <hostipname> { { key { 0 <s0> | 6 <s6> | 7 <s1> | <s2> } [ pac ] [ auth-port <i0>[ acct-port <i1> ] ] } | { [ auth-port1 <i2> ] [ acct-port1 <i3> ] } } [ { authentication [ accounting [ timeout<i4> ] [ retransmit <i5> ] ] } | { [ accounting1 ] [ timeout1 <i6> ] [ retransmit1 <i7> ] } ] } | { no radius-serverhost <hostipname> key } }
Syntax Description
0key
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
RADIUS server's DNS name or its IP addresshost
IPV4/IPV6 address or DNS namehostipname
RADIUS shared secretkey
(Optional) Secure Radius Enablepac
RADIUS shared secret(clear text)0
RADIUS shared secret(clear text)s0
(Optional) Use for accountingaccounting
(Optional) RADIUS server retransmit countretransmit
(Optional) RADIUS server retransmit counti5
(Optional) RADIUS server timeout period in secondstimeout
(Optional) RADIUS server timeout period in secondsi4
(Optional) RADIUS server retransmit countretransmit1
(Optional) RADIUS server retransmit counti7
(Optional) RADIUS server's port for authenticationauth-port
(Optional) port numberi0
(Optional) RADIUS server timeout period in secondstimeout1
(Optional) RADIUS server timeout period in secondsi6
(Optional) RADIUS server's port for accountingacct-port
(Optional) port numberi1
(Optional) Use for accountingaccounting1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3602
R Commandsradius-server host key 0 6 7
Page 3747
(Optional) Use for authenticationauthentication
Radius shared secret(type-6 encrypted)6
Tadius shared secret(encrypted)s6
RADIUS shared secret(encrypted)7
RADIUS shared secret(encrypted)s1
(Optional) RADIUS server's port for authenticationauth-port1
(Optional) port numberi2
RADIUS shared secret(clear text)s2
(Optional) RADIUS server's port for accountingacct-port1
(Optional) port numberi3
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3603
R Commandsradius-server host key 0 6 7
Page 3748
radius-server host test[no] radius-server host { <hostipname> } test { { username <s0> { [ password <s1> [ idle-time <i1> ] ] | [idle-time <i1> ] } } | { password <s1> [ idle-time <i1> ] } | { idle-time <i1> } }
Syntax Description
<s0>username
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
RADIUS server's DNS name or its IP addresshost
IPV4/IPV6 address or DNS namehostipname
Parameters to send test packetstest
user names0
(Optional) user password in test packetspassword
(Optional) user passwords1
(Optional) time interval for monitoring the serveridle-time
(Optional) time period in minutesi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3604
R Commandsradius-server host test
Page 3749
radius-server key 0 6 7{ { [ no ] radius-server key { 0 <s0> | 6 <s6> | 7 <s1> | <s2> } } | { no radius-server key } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
Global RADIUS server shared secretkey
default RADIUS shared secret(clear text)0
default RADIUS shared secret(clear text)s0
default RADIUS shared secret(type-6 encrypted)6
default RADIUS shared secret(type-6 encrypted)s6
default RADIUS shared secret(encrypted)7
default RADIUS shared secret(encrypted)s1
default RADIUS shared secret(clear text)s2
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3605
R Commandsradius-server key 0 6 7
Page 3750
radius-server pss-clean[no] radius-server pss-clean
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
Erase PSSpss-clean
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3606
R Commandsradius-server pss-clean
Page 3751
radius-server retransmit[no] radius-server retransmit <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
Global RADIUS server retransmit countretransmit
Global RADIUS server retransmit counti0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3607
R Commandsradius-server retransmit
Page 3752
radius-server test[no] radius-server test { { username <s0> { [ password <s1> [ idle-time <i1> ] ] | [ idle-time <i1> ] } } | {password <s1> [ idle-time <i1> ] } | { idle-time <i1> } }
Syntax Description
<s0>username
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
Parameters to send test packetstest
user names0
(Optional) user password in test packetspassword
(Optional) user passwords1
(Optional) time interval for monitoring the serveridle-time
(Optional) time period in minutesi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3608
R Commandsradius-server test
Page 3753
radius-server timeout[no] radius-server timeout <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure RADIUS related parametersradius-server
Global RADIUS server timeout period in secondstimeout
RADIUS server timeout period in secondsi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3609
R Commandsradius-server timeout
Page 3754
random-detect[no] random-detect [ { minimum-threshold <min-thresh> { packets | bytes | kbytes | mbytes }maximum-threshold <max-thresh> { packets1 | bytes1 | kbytes1 | mbytes1 } drop-probability <drop-prob>weight <weight> [ cap-average ] } | threshold { burst-optimized | mesh-optimized } ] [ ecn ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure WRED parametersrandom-detect
(Optional) Thresholdthreshold
(Optional) Threshold optimized for bursty trafficburst-optimized
(Optional) Threshold optimized for mesh trafficmesh-optimized
(Optional) Specify minimum threshold for WREDminimum-threshold
(Optional) Specify maximum threshold for WREDmaximum-threshold
(Optional) Maximum threshold valuemax-thresh
(Optional) Packetspackets
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Packetspackets1
(Optional) Bytesbytes1
(Optional) Kilo Byteskbytes1
(Optional) Mega Bytesmbytes1
(Optional) Drop Probability at Maximum Thresholddrop-probability
(Optional) Drop Probability Valuedrop-prob
(Optional) Queue length weightweight
(Optional) Queue length weightweight
(Optional) If average queue length is more, replace average queue lengthwith current queue length
cap-average
(Optional) ECNecn
Command Mode
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3610
R Commandsrandom-detect
Page 3755
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3611
R Commandsrandom-detect
Page 3756
random-detect2 minimum-threshold2 maximum-threshold2[no] random-detect2 minimum-threshold2 <min-thresh2> { packets2 | bytes2 | kbytes2 | mbytes2 }maximum-threshold2 <max-thresh2> { packets3 | bytes3 | kbytes3 | mbytes3 } [ drop-probability2 <drop-prob2>weight2 <weight2> [ cap-average2 ] ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure WRED parametersrandom-detect2
Specify minimum threshold for WREDminimum-threshold2
Specify maximum threshold for WREDmaximum-threshold2
Packetspackets2
Bytesbytes2
Kilo Byteskbytes2
Mega Bytesmbytes2
Packetspackets3
Bytesbytes3
Kilo Byteskbytes3
Mega Bytesmbytes3
(Optional) Drop Probability at Maximum Thresholddrop-probability2
(Optional) Drop Probability Valuedrop-prob2
(Optional) Queue length weightweight2
(Optional) Queue length weightweight2
(Optional) If average queue length is more, replace average queue lengthwith current queue length
cap-average2
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3612
R Commandsrandom-detect2 minimum-threshold2 maximum-threshold2
Page 3757
random-detect2 non-ecn minimum-threshold2maximum-threshold2 drop
[no] random-detect2 non-ecn minimum-threshold2 <min-thresh2> { packets2 | bytes2 | kbytes2 | mbytes2 }maximum-threshold2 <max-thresh2> { packets3 | bytes3 | kbytes3 | mbytes3 } { drop-probability2 <drop-prob2>}
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure WRED parametersrandom-detect2
Configure WRED parameters for non-ecnnon-ecn
Specify minimum threshold for WREDminimum-threshold2
Specify maximum threshold for WREDmaximum-threshold2
Packetspackets2
Bytesbytes2
Kilo Byteskbytes2
Mega Bytesmbytes2
Packetspackets3
Bytesbytes3
Kilo Byteskbytes3
Mega Bytesmbytes3
Drop Probability at Maximum Thresholddrop-probability2
Drop Probability Valuedrop-prob2
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3613
R Commandsrandom-detect2 non-ecn minimum-threshold2 maximum-threshold2 drop
Page 3758
random-detect[no] random-detect { cos <cos-list> [ minimum-threshold ] { <min-thresh> [ packets | bytes | kbytes | mbytes| ms | us ] | percent <min-percent-of-qsize> } [ maximum-threshold ] { <max-thresh> [ packets1 | bytes1 |kbytes1 | mbytes1 | ms1 | us1 ] | percent1 <max-percent-of-qsize> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure WRED parametersrandom-detect
Parameters for each cos valuecos
List of class-of-service valuescos-list
(Optional) Specify minimum threshold for WREDminimum-threshold
(Optional) Specify maximum threshold for WREDmaximum-threshold
Maximum threshold valuemax-thresh
Specify thresholds in percentpercent
Specify thresholds in percentpercent1
Minimum threshold percent of queue sizemin-percent-of-qsize
Maximum threshold percent of queue sizemax-percent-of-qsize
(Optional) Packetspackets
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Milli second(s)ms
(Optional) Micro second(s)us
(Optional) Packetspackets1
(Optional) Bytesbytes1
(Optional) Kilo Byteskbytes1
(Optional) Mega Bytesmbytes1
(Optional) Milli second(s)ms1
(Optional) Micro second(s)us1
Command Mode
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3614
R Commandsrandom-detect
Page 3759
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3615
R Commandsrandom-detect
Page 3760
random-detect cos-based[no] random-detect cos-based [ aggregate [ minimum-threshold ] { <min-thresh> [ packets | bytes | kbytes |mbytes | ms | us ] | percent <min-percent-of-qsize> } [ maximum-threshold ] { <max-thresh> [ packets1 |bytes1 | kbytes1 | mbytes1 | ms1 | us1 ] | percent1 <max-percent-of-qsize> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure WRED parametersrandom-detect
Configure WRED parameters for cos-based modecos-based
(Optional) ConfigureWREDparameters to same value for all sub-classesaggregate
(Optional) Specify minimum threshold for WREDminimum-threshold
(Optional) Specify maximum threshold for WREDmaximum-threshold
(Optional) Maximum threshold valuemax-thresh
(Optional) Specify thresholds in percentpercent
(Optional) Specify thresholds in percentpercent1
(Optional) Minimum threshold percent of queue sizemin-percent-of-qsize
(Optional) Maximum threshold percent of queue sizemax-percent-of-qsize
(Optional) Packetspackets
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
(Optional) Milli second(s)ms
(Optional) Micro second(s)us
(Optional) Packetspackets1
(Optional) Bytesbytes1
(Optional) Kilo Byteskbytes1
(Optional) Mega Bytesmbytes1
(Optional) Milli second(s)ms1
(Optional) Micro second(s)us1
Command Mode
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3616
R Commandsrandom-detect cos-based
Page 3761
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3617
R Commandsrandom-detect cos-based
Page 3762
rate-limitrate-limit { auto | <rate_value> } | no rate-limit
Syntax Description
Negate a command or set its defaultsno
Set the Rate limit for SPAN packetsrate-limit
Set the Rate limit using auto valueauto
Enter the percentage of the maximum rate for SPAN packetsrate_value
Command Mode
• /exec/configure/monitor-local-src /exec/configure/config-monitor/exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3618
R Commandsrate-limit
Page 3763
rate-limit cpu direction pps action log[no] rate-limit cpu direction { input | output | both } pps <pps-val> action log
Syntax Description
(Optional) Negate a command or set its defaultsno
set packet per second rate limitrate-limit
Supervisor CPU limitscpu
input/output directiondirection
set max input packet rateinput
set max output packet rateoutput
set max input and output packet rateboth
packet per secondpps
pps valuepps-val
log actionaction
write a syslog message if PPS hits rate-limitlog
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3619
R Commandsrate-limit cpu direction pps action log
Page 3764
rate-limit cpu direction pps action log[no] rate-limit cpu direction { input | output | both } pps <pps-val> action log
Syntax Description
(Optional) Negate a command or set its defaultsno
set packet per second rate limitrate-limit
Supervisor CPU limitscpu
input/output directiondirection
set max input packet rateinput
set max output packet rateoutput
set max input and output packet rateboth
packet per secondpps
pps valuepps-val
log actionaction
write a syslog message if PPS hits rate-limitlog
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-eth-any /exec/configure/if-mgmt-config
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3620
R Commandsrate-limit cpu direction pps action log
Page 3765
rate-limit packet_in burstrate-limit packet_in <packetin-val> burst <burst-val> | no rate-limit
Syntax Description
Negate a command or set its defaultsno
OpenFlow rate limit to controllerrate-limit
packet in rate (pps)packet_in
packets per secondpacketin-val
Maximum number of packets to controller (pps)burst
packets per secondburst-val
Command Mode
• /exec/configure/openflow/switch/sub-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3621
R Commandsrate-limit packet_in burst
Page 3766
rate-limit packet_in burstrate-limit packet_in <packetin-val> burst <burst-val> | no rate-limit
Syntax Description
Negate a command or set its defaultsno
OpenFlow rate limit to controllerrate-limit
packet in rate (pps)packet_in
packets per secondpacketin-val
Maximum number of packets to controller (pps)burst
packets per secondburst-val
Command Mode
• /exec/configure/openflow/switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3622
R Commandsrate-limit packet_in burst
Page 3767
rate-moderate-mode <ratemode> [ force ] | no rate-mode [ <ratemode> ] [ force ]
Syntax Description
Negate a command or set its defaultsno
Enter the rate moderate-mode
(Optional) This option will shutdown all ports in port-groupmomentarilyforce
Interface port speedratemode
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3623
R Commandsrate-mode
Page 3768
rd auto{ rd { auto | <ext-comm-rd-aa2nn4> | <ext-comm-rd-aa4nn2> } } | { no rd [ { auto | <ext-comm-rd-aa2nn4>| <ext-comm-rd-aa4nn2> } ] }
Syntax Description
Negate a command or set its defaultsno
VPN Route Distinguisherrd
Generate RD automaticallyauto
VPN route distinguisher in aa4:nn or ip:nn formatext-comm-rd-aa4nn2
VPN route distinguisher in aa:nn formatext-comm-rd-aa2nn4
Command Mode
• /exec/configure/evpn/evi
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3624
R Commandsrd auto
Page 3769
rd auto{ rd { auto | <ext-comm-rd-aa2nn4> | <ext-comm-rd-aa4nn2> } } | { no rd [ { auto | <ext-comm-rd-aa2nn4>| <ext-comm-rd-aa4nn2> } ] }
Syntax Description
Negate a command or set its defaultsno
VPN Route Distinguisherrd
Generate RD automaticallyauto
VPN route distinguisher in aa4:nn or ip:nn formatext-comm-rd-aa4nn2
VPN route distinguisher in aa:nn formatext-comm-rd-aa2nn4
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3625
R Commandsrd auto
Page 3770
receiver[no] receiver
Syntax Description
(Optional) Negate a command or set its defaultsno
Policies for a Local Receiverreceiver
Command Mode
• /exec/configure/nbm-host-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3626
R Commandsreceiver
Page 3771
reconnect-intervalreconnect-interval <interval> | no reconnect-interval [ <interval> ]
Syntax Description
Negate a command or set its defaultsno
Configure connection reconnect intervalreconnect-interval
Interval in secondsinterval
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3627
R Commandsreconnect-interval
Page 3772
record-route[no] record-route
Syntax Description
(Optional) Negate a command or set its defaultsno
Record the route used by the LSPrecord-route
Command Mode
• /exec/configure/te/lsp-attr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3628
R Commandsrecord-route
Page 3773
record-route[no] record-route
Syntax Description
(Optional) Negate a command or set its defaultsno
record the route used by the tunnelrecord-route
Command Mode
• /exec/configure/if-te /exec/configure/tunnel-te/cbts-member
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3629
R Commandsrecord-route
Page 3774
record[no] record <recordname>
Syntax Description
Specify POSTCARD Record to userecord
Name of recordrecordname
Command Mode
• /exec/configure/config-postcard-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3630
R Commandsrecord
Page 3775
record[no] record <recordname>
Syntax Description
Specify INT Record to userecord
Name of recordrecordname
Command Mode
• /exec/configure/config-int-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3631
R Commandsrecord
Page 3776
record[no] record <recordname>
Syntax Description
Specify FTE Record to userecord
Name of recordrecordname
Command Mode
• /exec/configure/config-fte-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3632
R Commandsrecord
Page 3777
record[no] record <recordname>
Syntax Description
Specify Flow Record to userecord
Name of recordrecordname
Command Mode
• /exec/configure/nfm-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3633
R Commandsrecord
Page 3778
record[no] record <recordname>
Syntax Description
Record to be monitoredrecord
Record name to be configuredrecordname
Command Mode
• /exec/configure/config-ssx-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3634
R Commandsrecord
Page 3779
redistribute bgp{ redistribute { { bgp <as> } | { eigrp | isis | ospfv3 | rip } <ptag> | static | direct | amt | lisp } route-map {<policy-name> | <rtr_pol_name> } } | { no redistribute { { bgp <as> } | { eigrp | isis | ospfv3 | rip } <ptag> |static | direct | amt | lisp } [ route-map { <policy-name> | <rtr_pol_name> } ] }
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
Enhanced Interior Gateway Protocol (EIGRP)eigrp
ISO Intermediate-to-Intermediate (IS-IS)isis
Open Shortest Path First (OSPFv3)ospfv3
Routing Information Protocol (RIP)rip
Process Tagptag
Staticstatic
Directly connecteddirect
AMT anycast prefixamt
LISP EID-prefixeslisp
Policy to constrain redistributionroute-map
Route-map namepolicy-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3635
R Commandsredistribute bgp
Page 3780
redistribute bgp eigrp isis ospf rip static direct amt lisproute-map
{ redistribute { bgp <as> | { eigrp | isis | ospf | rip } <ptag> | static | direct | amt | lisp } route-map {<policy-name> | <rtr_pol_name> } } | { no redistribute { bgp <as> | { eigrp | isis | ospf | rip } <ptag> | static| direct | amt | lisp } [ route-map { <policy-name> | <rtr_pol_name> } ] }
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
ISO Intermediate-to-Intermediate (IS-IS)isis
Open Shortest Path First (OSPFv2)ospf
Enhanced Interior Gateway Protocol (EIGRP)eigrp
Routing Information Protocol (RIP)rip
Protocol Tagptag
Staticstatic
Directly connecteddirect
AMT anycast prefixamt
LISP EID-prefixeslisp
Policy to constrain redistributionroute-map
Route-map namepolicy-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3636
R Commandsredistribute bgp eigrp isis ospf rip static direct amt lisp route-map
Page 3781
redistribute filter route-map[no] redistribute filter route-map { <map-name> | <rtr_pol_name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Filter redistributed routesfilter
Route-map to constrain redistributionroute-map
A 'routing-rules' route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3637
R Commandsredistribute filter route-map
Page 3782
redistribute filter route-map[no] redistribute filter route-map { <map-name> | <rtr_pol_name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Filter redistributed routesfilter
Route-map to constrain redistributionroute-map
A 'routing-rules' route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3638
R Commandsredistribute filter route-map
Page 3783
redistribute maximum-prefix{ redistribute maximum-prefix <maximum> [ <threshold> ] [ warning-only | withdraw [ <retries> <timeout>] ] } | { no redistribute maximum-prefix }
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Maximum number of prefixes redistributed to protocolmaximum-prefix
Maximum number of IP prefixes redistributedmaximum
(Optional) Threshold value (%) at which to generate a warning messagethreshold
(Optional) Log a warning message when limit is exceededwarning-only
(Optional) Withdraw all redistributed routeswithdraw
(Optional) Number of times to retry to get the redistributed routes againretries
(Optional) Timeout between each retriestimeout
Command Mode
• /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3639
R Commandsredistribute maximum-prefix
Page 3784
redistribute maximum-prefixredistribute maximum-prefix <maximum> [ <threshold> ] [ warning-only | withdraw [ <retries> <timeout>] ] | no redistribute maximum-prefix [ <maximum> [ <threshold> ] [ warning-only | withdraw [ <retries><timeout> ] ] ]
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Max number of prefixes redistributedmaximum-prefix
max numbermaximum
(Optional) Threshold in %, at which message is generatedthreshold
(Optional) Warning msg is logged when max is reachedwarning-only
(Optional) Withdraw all redistributed routeswithdraw
(Optional) No of times to retry to get redist routes againretries
(Optional) Time between the retriestimeout
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common /exec/configure/router-isis/router-isis-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3640
R Commandsredistribute maximum-prefix
Page 3785
redistribute maximum-prefixredistribute maximum-prefix <maximum> [ <threshold> ] [ warning-only | withdraw [ <retries> <timeout>] ] | no redistribute maximum-prefix [ <maximum> [ <threshold> ] [ warning-only | withdraw [ <retries><timeout> ] ] ]
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Max number of prefixes redistributedmaximum-prefix
max numbermaximum
(Optional) Threshold in %, at which message is generatedthreshold
(Optional) Warning msg is logged when max is reachedwarning-only
(Optional) Withdraw all redistributed routeswithdraw
(Optional) No of times to retry to get redist routes againretries
(Optional) Time between the retriestimeout
Command Mode
• /exec/configure/router-isis/router-isis-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3641
R Commandsredistribute maximum-prefix
Page 3786
redistribute maximum-prefixredistribute maximum-prefix <maximum> [ <threshold> ] [ warning-only | withdraw [ <retries> <timeout>] ] | no redistribute maximum-prefix [ <maximum> [ <threshold> ] [ warning-only | withdraw [ <retries><timeout> ] ] ]
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Max number of prefixes redistributedmaximum-prefix
max numbermaximum
(Optional) Threshold in %, at which message is generatedthreshold
(Optional) Warning msg is logged when threshold is reachedwarning-only
(Optional) Withdraw all redistributed routeswithdraw
(Optional) Number of attempts to receive redistributed routes after maxis reached
retries
(Optional) Retry intervaltimeout
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3642
R Commandsredistribute maximum-prefix
Page 3787
redistribute maximum-prefix{ redistribute maximum-prefix <maximum> [ <threshold> ] [ warning-only | withdraw [ <retries> <timeout>] ] } | { no redistribute maximum-prefix <maximum> [ <threshold> ] [ warning-only | withdraw [ <retries><timeout> ] ] }
Syntax Description
Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Maximum number of prefixes redistributed to protocolmaximum-prefix
Maximum number of IP prefixes redistributedmaximum
(Optional) Threshold value (%) at which to generate a warning messagethreshold
(Optional) Log a warning message when limit is exceededwarning-only
(Optional) Withdraw all redistributed routeswithdraw
(Optional) Number of times to retry to get the redistributed routes againretries
(Optional) Timeout between each retriestimeout
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3643
R Commandsredistribute maximum-prefix
Page 3788
redistribute route-map[no] redistribute { bgp <as> | { eigrp | isis | ospf | rip } <tag> | static | direct | amt } route-map { <map-name>| <rtr_pol_name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv4isis
Open Shortest Path First (OSPF)ospf
Enhanced Interior Gateway Protocoleigrp
RIP for IPv4rip
Process tagtag
Static routesstatic
Directly connecteddirect
AMT anycast prefixamt
Route-map to constrain redistributionroute-map
A 'routing-rules' route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3644
R Commandsredistribute route-map
Page 3789
redistribute route-map[no] redistribute { bgp <as> | { eigrp | isis | ospfv3 | rip } <tag> | static | direct | amt | lisp } route-map<map-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
RIP redistribute routes from other routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Intermediate-to-intermediate (ISIS)isis
Routing Information Protocol (RIP)rip
Open Shortest Path First (OSPFv3)ospfv3
Process tagtag
Static routesstatic
Directly connected routesdirect
AMT anycast prefixamt
LISP EID-prefixeslisp
Policy to constrain redistributionroute-map
Route-map namemap-name
Command Mode
• /exec/configure/router-rip/router-rip-af-ipv6 /exec/configure/router-rip/router-rip-vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3645
R Commandsredistribute route-map
Page 3790
redistribute route-map[no] redistribute { bgp <as> | { eigrp | isis | ospf | rip } <tag> | static | direct | amt | lisp } route-map <map-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
RIP redistribute routes from other routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Autonomous system numberas
Intermediate-to-intermediate (ISIS)isis
Routing Information Protocol (RIP)rip
Open Shortest Path First (OSPFv2)ospf
Process tagtag
Static routesstatic
Directly connected routesdirect
AMT anycast prefixamt
LISP EID-prefixeslisp
Policy to constrain redistributionroute-map
Route-map namemap-name
Command Mode
• /exec/configure/router-rip/router-rip-af-ipv4 /exec/configure/router-rip/router-rip-vrf-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3646
R Commandsredistribute route-map
Page 3791
redistribute route-map[no] redistribute { bgp <as> | { eigrp | isis | ospf | rip } <tag> | static | direct | amt } route-map { <map-name>| <rtr_pol_name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv4isis
Open Shortest Path First (OSPF)ospf
Enhanced Interior Gateway Protocoleigrp
RIP for IPv4rip
Process tagtag
Static routesstatic
Directly connecteddirect
AMT anycast prefixamt
Route-map to constrain redistributionroute-map
A 'routing-rules' route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common /exec/configure/router-isis/router-isis-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3647
R Commandsredistribute route-map
Page 3792
redistribute route-map[no] redistribute { bgp <as> | { eigrp | isis | ospfv3 | rip } <tag> | static | direct | amt } route-map { <map-name>| <rtr_pol_name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv6isis
Open Shortest Path First (OSPF) V3ospfv3
Enhanced Interior Gateway Protocoleigrp
RIP for IPv6 (RIPNG)rip
Process tagtag
Static routesstatic
Directly connecteddirect
AMT anycast prefixamt
Route-map to constrain redistributionroute-map
A 'routing-rules' route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/router-isis/router-isis-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3648
R Commandsredistribute route-map
Page 3793
redistribute route-map[no] redistribute { bgp <as> | { eigrp | isis | ospf | rip } <tag> | static | direct | amt | lisp } route-map {<map-name> | <rtr_pol_name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv4isis
Open Shortest Path First (OSPF)ospf
Routing Information Protocol (RIP)rip
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Process tagtag
Static routesstatic
Directly connecteddirect
LISP EID-prefixeslisp
AMT Anycast prefixamt
Route-map to constrain redistributionroute-map
Route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3649
R Commandsredistribute route-map
Page 3794
redistribute route-map[no] redistribute { bgp <as> | { eigrp | isis | ospfv3 | rip } <tag> | static | direct | amt | lisp } route-map {<map-name> | <rtr_pol_name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv4isis
Open Shortest Path First (OSPF) V3ospfv3
Routing Information Protocol (RIP)rip
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Process tagtag
Static routesstatic
Directly connecteddirect
AMT Anycast prefixamt
LISP EID-prefixeslisp
Route-map to constrain redistributionroute-map
Route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/router-eigrp/router-eigrp-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3650
R Commandsredistribute route-map
Page 3795
redistribute route-map[no] redistribute { static | direct | amt | lisp | am | hmm | { { eigrp | isis | ospf | rip } <tag> } } route-map<rmap-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure redistributionredistribute
Static routesstatic
Directly connecteddirect
ISO IS-ISisis
Open Shortest Path First (OSPF)ospf
Routing Information Protocol (RIP)rip
Enhanced Interior Gateway Protocoleigrp
AMT anycast prefixamt
LISP EID-prefixes in the non-default VRFlisp
AM routes (learned via ARP)am
HMM prefixhmm
Route-map applied to redistributed routesroute-map
Route-map namermap-name
Source protocol tagtag
Command Mode
• /exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3651
R Commandsredistribute route-map
Page 3796
redistribute route-map[no] redistribute { static | direct | amt | lisp | am | hmm | { { eigrp | isis | ospfv3 | rip } <tag> } } route-map<rmap-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure redistributionredistribute
Static routesstatic
Directly connecteddirect
ISO IS-ISisis
Open Shortest Path First, version 3 (OSPFv3)ospfv3
Routing Information Protocol (RIP)rip
Enhanced Interior Gateway Protocoleigrp
AMT anycast prefixamt
LISP EID-prefixes in the non-default VRFlisp
HMM prefixhmm
AM routes (learned via ARP)am
Route-map applied to redistributed routesroute-map
Route-map namermap-name
Source protocol tagtag
Command Mode
• /exec/configure/router-bgp/router-bgp-af-ipv6 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3652
R Commandsredistribute route-map
Page 3797
redistribute route-map[no] redistribute { bgp <as> | { eigrp | isis | ospfv3 | rip } <tag> | static | direct | amt } route-map { <map-name>| <rtr_pol_name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Redistribute information from another routing protocolredistribute
Border Gateway Protocol (BGP)bgp
Autonomous system numberas
IS-IS Routing for IPv6isis
Open Shortest Path First (OSPF) V3ospfv3
Enhanced Interior Gateway Protocoleigrp
RIP for IPv6 (RIPNG)rip
Process tagtag
Static routesstatic
Directly connecteddirect
AMT anycast prefixamt
Route-map to constrain redistributionroute-map
A 'routing-rules' route-map namemap-name
An existing routing-rules policyrtr_pol_name
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3653
R Commandsredistribute route-map
Page 3798
redownload forwarding stateredownload forwarding [ ipv4 | ipv6 | all ] state
Syntax Description
redownloadredownload
forwardingforwarding
(Optional) ipv4ipv4
(Optional) ipv6ipv6
(Optional) both ipv4 and ipv6all
statestate
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3654
R Commandsredownload forwarding state
Page 3799
redundancy-group[no] redundancy-group
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a redundancy-group noderedundancy-group
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3655
R Commandsredundancy-group
Page 3800
reference-bandwidth[no] reference-bandwidth { <ref-bw-mbps> [ Mbps ] | <ref-bw-gbps> Gbps }
Syntax Description
(Optional) Negate a command or set its defaultsno
Change reference bandwidth used for setting interface metricreference-bandwidth
Bandwidth in Mbps (Default)ref-bw-mbps
(Optional) Specify in MbpsMbps
Bandwidth in Gbpsref-bw-gbps
Specify in GbpsGbps
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3656
R Commandsreference-bandwidth
Page 3801
reference-bandwidth[no] reference-bandwidth { <ref-bw-mbps> [ Mbps ] | <ref-bw-gbps> Gbps }
Syntax Description
(Optional) Negate a command or set its defaultsno
Change reference bandwidth used for setting interface metricreference-bandwidth
Bandwidth in Mbps (Default)ref-bw-mbps
(Optional) Specify in MbpsMbps
Bandwidth in Gbpsref-bw-gbps
Specify in GbpsGbps
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common /exec/configure/l2mp-isis/l2mp-isis-l2-topo
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3657
R Commandsreference-bandwidth
Page 3802
register-database-mapping{ [ no ] register-database-mapping }
Syntax Description
(Optional) Negate a command or set its defaultsno
Register database-mapping EID-prefix to Map-Serverregister-database-mapping
Command Mode
• /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3658
R Commandsregister-database-mapping
Page 3803
register-route-notifications{ [ no ] register-route-notifications }
Syntax Description
(Optional) Negate a command or set its defaultsno
Register more-specific routes of the database-mapping EID-prefix toMap-Server
register-route-notifications
Command Mode
• /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3659
R Commandsregister-route-notifications
Page 3804
reloadreload
Syntax Description
reboot the entire boxreload
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3660
R Commandsreload
Page 3805
reload cancelreload cancel
Syntax Description
reboot the entire boxreload
Cancel scheduling of the reloadcancel
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3661
R Commandsreload cancel
Page 3806
reload inreload in <secs>
Syntax Description
reboot the entire boxreload
Schedule a reload after some timein
Reload after n secondssecs
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3662
R Commandsreload in
Page 3807
reload modulereload module <lem-aware-module>
Syntax Description
reboot the entire boxreload
reboot a specific modulemodule
please enter the module numberlem-aware-module
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3663
R Commandsreload module
Page 3808
reload module force-dnldreload module <module> force-dnld
Syntax Description
reboot the entire boxreload
reboot a specific modulemodule
please enter the module numbermodule
reboot a specific module to force NetBoot and image downloadforce-dnld
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3664
R Commandsreload module force-dnld
Page 3809
reload non-interruptivereload non-interruptive
Syntax Description
reboot the entire boxreload
Reboot without interruptionnon-interruptive
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3665
R Commandsreload non-interruptive
Page 3810
reload power-cyclereload power-cycle
Syntax Description
reboot the entire boxreload
Power cycle ADMpower-cycle
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3666
R Commandsreload power-cycle
Page 3811
reload sync-adjacencyreload sync-adjacency
Syntax Description
reload with sync adjacencyreload
Reload with ARP/ND sync adjacencysync-adjacency
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3667
R Commandsreload sync-adjacency
Page 3812
reload sync-adjacencyreload sync-adjacency
Syntax Description
reboot the entire boxreload
Reload with sync adjacencysync-adjacency
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3668
R Commandsreload sync-adjacency
Page 3813
reload timerreload timer <secs>
Syntax Description
reboot the entire boxreload
reboot after a delay <5-3600> secondstimer
delay in secondssecs
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3669
R Commandsreload timer
Page 3814
reload vdcreload vdc <d-vdc>
Syntax Description
Restart the current vdcvdc
Power cyclereload
Enter Virtual Device Context <vdc-id>d-vdc
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3670
R Commandsreload vdc
Page 3815
reload vdcreload vdc
Syntax Description
Restart the current vdcvdc
Power cyclereload
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3671
R Commandsreload vdc
Page 3816
remark{ [ <seqno> ] | no } remark <comment>
Syntax Description
Negate a command or set its defaultsno
(Optional) Sequence numberseqno
Access list entry commentremark
Comment, up to 100 characterscomment
Command Mode
• /exec/configure/arpacl /exec/configure/timerange
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3672
R Commandsremark
Page 3817
remark{ [ <seqno> ] | no } remark <comment>
Syntax Description
Negate a command or set its defaultsno
(Optional) Sequence numberseqno
Access list entry commentremark
Comment, up to 100 characterscomment
Command Mode
• /exec/configure/ipacl /exec/configure/ipv6acl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3673
R Commandsremark
Page 3818
remark{ [ <seqno> ] | no } remark <comment>
Syntax Description
Negate a command or set its defaultsno
(Optional) Sequence numberseqno
Access list entry commentremark
Comment, up to 100 characterscomment
Command Mode
• /exec/configure/macacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3674
R Commandsremark
Page 3819
remote-as{ remote-as <asn> } | { { no | default } remote-as [ <asn> ] }
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Specify Autonomous System Number of the neighborremote-as
Autonomous System Numberasn
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3675
R Commandsremote-as
Page 3820
remote-span[no] remote-span
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable remote span VLANremote-span
Command Mode
• /exec/configure/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3676
R Commandsremote-span
Page 3821
remoteremote { { ip address { <ipaddress> } | hostname <host_name> } [ port <port_no> ] [ vrf { <vrf-name> |<vrf-known-name> } ] | port <port_no> | vrf { <vrf-name> | <vrf-known-name> } } | no remote { ip address| hostname | port }
Syntax Description
Negate a command or set its defaultsno
Configure remote machine informationremote
Configure IP featuresip
Configure IP addressaddress
Enter ipv4 address informationipaddress
Configure remote host namehostname
Enter name of the remote hosthost_name
(Optional) Configure remote host tcp portport
(Optional) Configure the host tcp port numberport_no
(Optional) vrf via which the vCenter Server is reachablevrf
(Optional) Specify the vrf-namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure/vmt-conn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3677
R Commandsremote
Page 3822
remove-private-as[ no | default ] remove-private-as [ all | replace-as ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Remove private AS number from outbound updatesremove-private-as
(Optional) Allall
(Optional) Replacereplace-as
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3678
R Commandsremove-private-as
Page 3823
reoptimize events link-up[no] reoptimize events link-up | no reoptimize timers { delay { cleanup | installation } | frequency } | reoptimizetimers { delay { cleanup <clean_sec> | installation <inst_sec> } | frequency <freq_sec> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Reoptimization parametersreoptimize
Reoptimization triggersevents
Reoptimize tunnels on link up eventslink-up
Reoptimization timerstimers
Delay reoptimization actiondelay
Delay cleanup of reoptimized LSPcleanup
seconds to delay cleanup of replaced tunnel LSPclean_sec
Delay replacement of current LSP by reoptimized LSPinstallation
seconds to delay replacement of tunnel LSPinst_sec
Interval between reoptimization scansfrequency
seconds between reoptimizations (0 disables reoptimization)freq_sec
Command Mode
• /exec/configure/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3679
R Commandsreoptimize events link-up
Page 3824
replay-protection[no] replay-protection
Syntax Description
Enable replay-protection (the default use the no form to disable)replay-protection
Command Mode
• /exec/configure/cts-dot1x /exec/configure/cts-manual
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3680
R Commandsreplay-protection
Page 3825
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/outsel2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3681
R Commandsreport
Page 3826
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/insel6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3682
R Commandsreport
Page 3827
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/insel7
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3683
R Commandsreport
Page 3828
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/insel8
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3684
R Commandsreport
Page 3829
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/insel9
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3685
R Commandsreport
Page 3830
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/insel10
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3686
R Commandsreport
Page 3831
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/insel19
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3687
R Commandsreport
Page 3832
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/outsel0
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3688
R Commandsreport
Page 3833
reportreport [ detail ]
Syntax Description
Show trigger report summaryreport
(Optional) Show detailed trigger reportdetail
Command Mode
• /exec/elamtah/outsel1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3689
R Commandsreport
Page 3834
reportreport
Syntax Description
Show trigger reportreport
Command Mode
• /exec/elamns/sel3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3690
R Commandsreport
Page 3835
reportreport
Syntax Description
Show trigger reportreport
Command Mode
• /exec/elamns/sel4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3691
R Commandsreport
Page 3836
reportreport
Syntax Description
Show trigger reportreport
Command Mode
• /exec/elamns/sel5
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3692
R Commandsreport
Page 3837
reportreport
Syntax Description
Show trigger reportreport
Command Mode
• /exec/elamns/sel6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3693
R Commandsreport
Page 3838
reportreport
Syntax Description
Show trigger reportreport
Command Mode
• /exec/elamns/sel7
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3694
R Commandsreport
Page 3839
reportreport
Syntax Description
Show trigger reportreport
Command Mode
• /exec/elamns/outsel0
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3695
R Commandsreport
Page 3840
reportreport
Syntax Description
Show trigger reportreport
Command Mode
• /exec/elamns/outsel5
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3696
R Commandsreport
Page 3841
request-data-size{ { no | default } request-data-size | request-data-size <bytes-in-payload> }
Syntax Description
no
Set a command to its defaultsdefault
Request data sizerequest-data-size
Number of bytes in payloadbytes-in-payload
Command Mode
• /exec/configure/ip-sla/jitter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3697
R Commandsrequest-data-size
Page 3842
request-data-size{ { no | default } request-data-size | request-data-size <bytes-in-payload> }
Syntax Description
no
Set a command to its defaultsdefault
Request data sizerequest-data-size
Number of bytes in payloadbytes-in-payload
Command Mode
• /exec/configure/ip-sla/udp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3698
R Commandsrequest-data-size
Page 3843
request-data-size{ { no | default } request-data-size | request-data-size <bytes-in-payload> }
Syntax Description
no
Set a command to its defaultsdefault
Request data sizerequest-data-size
Number of bytes in payloadbytes-in-payload
Command Mode
• /exec/configure/ip-sla/icmpEcho
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3699
R Commandsrequest-data-size
Page 3844
resequence accessresequence { { <ip_ipv6_mac_arp> access-list } | time-range } <name> <number> <increment>
Syntax Description
Resequence a list with sequence numbersresequence
IP/IPv6/MAC/ARPip_ipv6_mac_arp
Resequence an access listaccess-list
Resequence a time-rangetime-range
List namename
Starting sequence numbernumber
Step to increment the sequence numberincrement
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3700
R Commandsresequence access
Page 3845
resetreset
Syntax Description
Reset Trigger Filtersreset
Command Mode
• /exec/elamtah/insel7
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3701
R Commandsreset
Page 3846
resetreset
Syntax Description
Reset Trigger Filtersreset
Command Mode
• /exec/elamtah/insel6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3702
R Commandsreset
Page 3847
resetreset
Syntax Description
Reset Trigger Filtersreset
Command Mode
• /exec/elamtah/insel8
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3703
R Commandsreset
Page 3848
resetreset
Syntax Description
Reset Trigger Filtersreset
Command Mode
• /exec/elamtah/insel9
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3704
R Commandsreset
Page 3849
resetreset
Syntax Description
Reset Trigger Filtersreset
Command Mode
• /exec/elamtah/insel10
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3705
R Commandsreset
Page 3850
resetreset
Syntax Description
Reset Trigger Filtersreset
Command Mode
• /exec/elamtah/insel19
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3706
R Commandsreset
Page 3851
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamtah/outsel0
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3707
R Commandsreset
Page 3852
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamtah/outsel1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3708
R Commandsreset
Page 3853
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamtah/outsel2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3709
R Commandsreset
Page 3854
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamns/sel3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3710
R Commandsreset
Page 3855
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamns/sel4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3711
R Commandsreset
Page 3856
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamns/sel5
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3712
R Commandsreset
Page 3857
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamns/sel6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3713
R Commandsreset
Page 3858
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamns/sel7
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3714
R Commandsreset
Page 3859
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamns/outsel0
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3715
R Commandsreset
Page 3860
resetreset
Syntax Description
Reset Trigger conditionsreset
Command Mode
• /exec/elamns/outsel5
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3716
R Commandsreset
Page 3861
restart amtrestart amt
Syntax Description
Manually restart a componentrestart
Restart the AMT multicast routing protocolamt
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3717
R Commandsrestart amt
Page 3862
restart bgprestart bgp <as>
Syntax Description
Manually restart a componentrestart
Border Gateway Protocol (BGP)bgp
Autonomousas
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3718
R Commandsrestart bgp
Page 3863
restart eigrprestart eigrp <eigrp-ptag>
Syntax Description
Manually restart a componentrestart
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Process tageigrp-ptag
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3719
R Commandsrestart eigrp
Page 3864
restart igmprestart igmp
Syntax Description
Manually restart a componentrestart
Restart the IGMP multicast routing protocoligmp
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3720
R Commandsrestart igmp
Page 3865
restart isisrestart isis <tag>
Syntax Description
Manually restart a componentrestart
Intermediate System to Intermediate System (IS-IS)isis
Routing process tagtag
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3721
R Commandsrestart isis
Page 3866
restart msdprestart msdp
Syntax Description
Manually restart a componentrestart
Restart the MSDP multicast routing protocolmsdp
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3722
R Commandsrestart msdp
Page 3867
restart ospfrestart ospf <tag>
Syntax Description
Manually restart a componentrestart
Open Shortest Path First (OSPF)ospf
Process tagtag
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3723
R Commandsrestart ospf
Page 3868
restart ospfv3restart ospfv3 <tag>
Syntax Description
Manually restart a componentrestart
Open Shortest Path First (OSPF) (Version 3)ospfv3
Process tagtag
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3724
R Commandsrestart ospfv3
Page 3869
restart pimrestart pim
Syntax Description
Manually restart a componentrestart
Restart the PIM multicast routing protocolpim
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3725
R Commandsrestart pim
Page 3870
restart pim6restart pim6
Syntax Description
Manually restart a componentrestart
Restart the PIM6 multicast routing protocolpim6
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3726
R Commandsrestart pim6
Page 3871
restart riprestart rip <tag>
Syntax Description
Manually restart a componentrestart
Routing Information Protocol (RIP)rip
Process IDtag
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3727
R Commandsrestart rip
Page 3872
restart rsvprestart rsvp
Syntax Description
Manually restart a processrestart
RSVP processrsvp
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3728
R Commandsrestart rsvp
Page 3873
resync-databaseresync-database
Syntax Description
Re-synchronize switch-profile databaseresync-database
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3729
R Commandsresync-database
Page 3874
retain route-target all[no] retain route-target { all | route-map <rmap-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Retain the routes based on Target VPN Extended Communitiesretain
Specify Target VPN Extended Communitiesroute-target
All the routes regardless of Target-VPN communityall
Apply route-map to filter routesroute-map
Route-map namermap-name
Command Mode
• /exec/configure/router-bgp/router-bgp-af-l2vpn-vpls
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3730
R Commandsretain route-target all
Page 3875
retain route-target all[no] retain route-target { all | route-map <rmap-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Retain the routes based on Target VPN Extended Communitiesretain
Specify Target VPN Extended Communitiesroute-target
All the routes regardless of Target-VPN communityall
Apply route-map to filter routesroute-map
Route-map namermap-name
Command Mode
• /exec/configure/router-bgp/router-bgp-af-vpnv4 /exec/configure/router-bgp/router-bgp-af-vpnv6/exec/configure/router-bgp/router-bgp-af-link-state /exec/configure/router-bgp/router-bgp-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-af-ipv4-mvpn /exec/configure/router-bgp/router-bgp-af-ipv6-mvpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3731
R Commandsretain route-target all
Page 3876
retransmit-interval{ { retransmit-interval <interval> } | { no retransmit-interval [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Packet retransmission intervalretransmit-interval
(seconds)interval
Command Mode
• /exec/configure/router-ospf3/router-ospf3-vlink /exec/configure/router-ospf3/vrf/router-ospf3-vlink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3732
R Commandsretransmit-interval
Page 3877
retransmit-interval{ { retransmit-interval <interval> } | { no retransmit-interval [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Packet retransmission intervalretransmit-interval
(seconds)interval
Command Mode
• /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3733
R Commandsretransmit-interval
Page 3878
retransmit-interval{ { retransmit-interval <interval> } | { no retransmit-interval [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Packet retransmission intervalretransmit-interval
(seconds)interval
Command Mode
• /exec/configure/router-ospf/vrf/router-ospf-slink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3734
R Commandsretransmit-interval
Page 3879
revisionrevision <rev-id> | no revision [ <rev-id> ]
Syntax Description
Negate a command or set its defaultsno
Set configuration revision numberrevision
Configuration revision numberrev-id
Command Mode
• /exec/configure/spanning-tree/mst/configuration
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3735
R Commandsrevision
Page 3880
revocation-check crl[no] revocation-check { crl [ none ] | none }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure trustpoint revocation check methodsrevocation-check
Configure revocation check using crlcrl
(Optional) Configure revocation check using nonenone
Configure revocation check using nonenone
Command Mode
• /exec/configure/trustpoint
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3736
R Commandsrevocation-check crl
Page 3881
rewrite-evpn-rt-asn[ no | default ] rewrite-evpn-rt-asn
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Auto generate RTs for EBGP neighborrewrite-evpn-rt-asn
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3737
R Commandsrewrite-evpn-rt-asn
Page 3882
rewrite-rt-asn[ no | default ] rewrite-rt-asn
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Auto generate RTs for EBGP neighborrewrite-rt-asn
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3738
R Commandsrewrite-rt-asn
Page 3883
rfc1583compatibility[no] rfc1583compatibility
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure 1583 compatibility for external path preferencesrfc1583compatibility
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3739
R Commandsrfc1583compatibility
Page 3884
rip shutdown[no] rip shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
RIP configuration commandsrip
Shutdown RIP on this interfaceshutdown
Command Mode
• /exec/configure/if-igp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3740
R Commandsrip shutdown
Page 3885
rmdirrmdir { <uri0> | <uri1> }
Syntax Description
Delete a directoryrmdir
Delete a directoryuri0
Delete a directory on expansion flashuri1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3741
R Commandsrmdir
Page 3886
rmon alarm absolute rising-threshold falling-thresholdrmon alarm <i0> <s0> <i1> { absolute | delta } rising-threshold <i2> [ <i3> ] falling-threshold <i4> [ <i5> ][ owner <s1> ] | no rmon alarm <i0>
Syntax Description
Negate a command or set its defaultsno
Remote Monitoringrmon
Configure an RMON alarmalarm
Alarm numberi0
MIB object to monitors0
Sample intervali1
Test each sample directlyabsolute
Test delta between samplesdelta
Configure the rising thresholdrising-threshold
Rising threshold valuei2
(Optional) Event to fire on rising threshold crossingi3
Configure the falling thresholdfalling-threshold
Falling threshold valuei4
(Optional) Event to fire on falling threshold crossingi5
(Optional) Specify an owner for the alarmowner
(Optional) Alarm owners1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3742
R Commandsrmon alarm absolute rising-threshold falling-threshold
Page 3887
rmon eventrmon event <i0> [ log ] [ trap <s0> ] [ description <s1> ] [ owner <s2> ] | no rmon event <i0>
Syntax Description
Negate a command or set its defaultsno
Remote Monitoringrmon
Configure an RMON eventevent
Event numberi0
(Optional) Generate RMON log when the event fireslog
(Optional) Generate SNMP trap when event firestrap
(Optional) SNMP community strings0
(Optional) Specify a description of the eventdescription
(Optional) Event descriptions1
(Optional) Specify an owner for the eventowner
(Optional) Event owners2
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3743
R Commandsrmon event
Page 3888
rmon hcalarm absolute startupalarm rising-thresholdfalling-threshold owner
rmon hcalarm <i0> <s0> <i1> { absolute | delta } startupalarm <i2> rising-threshold <i3> <i4> falling-threshold<i5> <i6> owner <s1> | no rmon hcalarm <i0>
Syntax Description
Negate a command or set its defaultsno
Remote Monitoringrmon
Configure an High Capacity RMON alarmhcalarm
Alarm numberi0
MIB object to monitors0
Sample intervali1
Test each sample directlyabsolute
Test delta between samplesdelta
Configure alarm typestartupalarm
Startup alarm type, rising(1) falling(2) risingorfalling(3)i2
Configure the rising thresholdrising-threshold
Rising threshold value in bytesi3
Event to fire on rising threshold crossingi4
Configure the falling thresholdfalling-threshold
Falling threshold value in bytesi5
Event to fire on falling threshold crossingi6
Specify an owner for the alarmowner
Alarm owners1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3744
R Commandsrmon hcalarm absolute startupalarm rising-threshold falling-threshold owner
Page 3889
roaming-eid-prefix{ [ no ] roaming-eid-prefix { <eid-prefix> | <eid-prefix6> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configures what EID-prefixes allowed to roamroaming-eid-prefix
IPv4 roaming EID-prefixeid-prefix
Command Mode
• /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3745
R Commandsroaming-eid-prefix
Page 3890
role feature-group name[no] role feature-group name <arg6>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure rolesrole
Configure role feature-groupfeature-group
Feature-group namename
Enter feature-group namearg6
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3746
R Commandsrole feature-group name
Page 3891
role name[no] role name <arg2>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure rolesrole
Enter the role namename
Enter the role namearg2
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3747
R Commandsrole name
Page 3892
role priorityrole priority <priority_value> | no role priority
Syntax Description
Negate a command or set its defaultsno
Role related configurationrole
Configure priority to be used during vPC role (primary/secondary)election
priority
specify priority valuepriority_value
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3748
R Commandsrole priority
Page 3893
rollback running-config checkpointrollback running-config { checkpoint <chkpoint_name> | file <file_uri> } [ best-effort | stop-at-first-failure |atomic ] [ verbose ]
Syntax Description
Rollback configurationrollback
Rollback running configurationrunning-config
Rollback running configuration to checkpointcheckpoint
Checkpoint namechkpoint_name
Rollback running configuration to configuration filefile
Checkpoint file pathfile_uri
(Optional) Skip errors and proceed with rollbackbest-effort
(Optional) Stop rollback at the first errorstop-at-first-failure
(Optional) Stop rollback and revert to original configuration (default)atomic
(Optional) Show the execution logverbose
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3749
R Commandsrollback running-config checkpoint
Page 3894
root-priority[no] root-priority <root-pri>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set priority with which nodes becomes rootroot-priority
Root priority value per topologyroot-pri
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common /exec/configure/l2mp-isis/l2mp-isis-l2-topo
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3750
R Commandsroot-priority
Page 3895
route-map[no] route-map { <rtmap-name> | <rtmap-name> } [ permit | deny ] <seq>
Syntax Description
Negate a command or set its defaultsno
Create route-map or enter route-map command moderoute-map
Route-map namertmap-name
Known route-map namertmap-name
(Optional) Route map permits set operationspermit
(Optional) Route map denies set operationsdeny
Sequence to insert to/delete from existing route-map entryseq
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3751
R Commandsroute-map
Page 3896
route-maproute-map <rtmap-name> [ permit | deny ]
Syntax Description
Create route-map or enter route-map command moderoute-map
Route-map namertmap-name
(Optional) Route map permits set operationspermit
(Optional) Route map denies set operationsdeny
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3752
R Commandsroute-map
Page 3897
route-maproute-map <rtmap-name> [ permit | deny ] <seq>
Syntax Description
Create route-map or enter route-map command moderoute-map
Route-map namertmap-name
(Optional) Route map permits set operationspermit
(Optional) Route map denies set operationsdeny
Sequence to insert to/delete from existing route-map entryseq
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3753
R Commandsroute-map
Page 3898
route-map[no] route-map { <rtmap-name> | <rtmap-name> } [ permit | deny ]
Syntax Description
Negate a command or set its defaultsno
Create route-map or enter route-map command moderoute-map
Route-map namertmap-name
Known route-map namertmap-name
(Optional) Route map permits set operationspermit
(Optional) Route map denies set operationsdeny
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3754
R Commandsroute-map
Page 3899
route-map out[ no | default ] route-map <rmap-name> { out | in }
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Apply route-map to neighborroute-map
Route-map namermap-name
Apply policy to outgoing routesout
Apply policy to incoming routesin
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3755
R Commandsroute-map out
Page 3900
route-map pbr-statisticsroute-map <route-map-name> pbr-statistics | no route-map { <route-map-name> | <route-map-name> }pbr-statistics
Syntax Description
Negate a command or set its defaultsno
Create route-map or enter route-map command moderoute-map
Route-map nameroute-map-name
Route-map nameroute-map-name
Known route-map nameroute-map-name
Statistics for policy based routingpbr-statistics
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3756
R Commandsroute-map pbr-statistics
Page 3901
route-reflector-client[ no | default ] route-reflector-client
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure a neighbor as Route reflector clientroute-reflector-client
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3757
R Commandsroute-reflector-client
Page 3902
route-reflector-client[ no | default ] route-reflector-client
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Configure a neighbor as Route reflector clientroute-reflector-client
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-link-state/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3758
R Commandsroute-reflector-client
Page 3903
route-target both auto{ route-target both { auto | <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } [ evpn | mvpn ] } | { no route-targetboth [ auto [ evpn | mvpn ] | <ext-comm-rt-aa2nn4> [ evpn | mvpn ] | <ext-comm-rt-aa4nn2> [ evpn | mvpn] ] }
Syntax Description
Negate a command or set its defaultsno
Specify Target VPN Extended Communitiesroute-target
Export And Import Target-VPN communityboth
Generate route target automaticallyauto
(Optional) Specify Target for EVPN routesevpn
(Optional) Specify Target for MVPN routesmvpn
RT extcommunity in aa4:nn or ip:nn formatext-comm-rt-aa4nn2
RT extcommunity in aa:nn formatext-comm-rt-aa2nn4
Command Mode
• /exec/configure/vrf-af-ipv4 /exec/configure/vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3759
R Commandsroute-target both auto
Page 3904
route-target both auto{ route-target both { auto | <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } } | { no route-target both { auto| <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } }
Syntax Description
Negate a command or set its defaultsno
Specify Target VPN Extended Communitiesroute-target
Generate RT automaticallyauto
Export and Import Target-VPN communityboth
RT extcommunity in aa4:nn or ip:nn formatext-comm-rt-aa4nn2
RT extcommunity in aa:nn formatext-comm-rt-aa2nn4
Command Mode
• /exec/configure/evpn/evi
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3760
R Commandsroute-target both auto
Page 3905
route-target export{ route-target export { <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } [ evpn | mvpn ] } | { no route-targetexport { <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } [ evpn | mvpn ] }
Syntax Description
Negate a command or set its defaultsno
Specify Target VPN Extended Communitiesroute-target
Export Target-VPN communityexport
(Optional) Specify Target for EVPN routesevpn
(Optional) Specify Target for MVPN routesmvpn
RT extcommunity in aa4:nn or ip:nn formatext-comm-rt-aa4nn2
RT extcommunity in aa:nn formatext-comm-rt-aa2nn4
Command Mode
• /exec/configure/vrf-af-ipv4 /exec/configure/vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3761
R Commandsroute-target export
Page 3906
route-target export auto{ route-target export { auto | <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } } | { no route-target export {auto | <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } }
Syntax Description
Negate a command or set its defaultsno
Specify Target VPN Extended Communitiesroute-target
Generate RT automaticallyauto
Export Target-VPN communityexport
RT extcommunity in aa4:nn or ip:nn formatext-comm-rt-aa4nn2
RT extcommunity in aa:nn formatext-comm-rt-aa2nn4
Command Mode
• /exec/configure/evpn/evi
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3762
R Commandsroute-target export auto
Page 3907
route-target import{ route-target import { <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } [ evpn | mvpn ] } | { no route-targetimport { <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } [ evpn | mvpn ] }
Syntax Description
Negate a command or set its defaultsno
Specify Target VPN Extended Communitiesroute-target
Import Target-VPN communityimport
(Optional) Specify Target for EVPN routesevpn
(Optional) Specify Target for MVPN routesmvpn
RT extcommunity in aa4:nn or ip:nn formatext-comm-rt-aa4nn2
RT extcommunity in aa:nn formatext-comm-rt-aa2nn4
Command Mode
• /exec/configure/vrf-af-ipv4 /exec/configure/vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3763
R Commandsroute-target import
Page 3908
route-target import auto{ route-target import { auto | <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } } | { no route-target import{ auto | <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } }
Syntax Description
Negate a command or set its defaultsno
Specify Target VPN Extended Communitiesroute-target
Import Target-VPN communityimport
Generate RT automaticallyauto
RT extcommunity in aa4:nn or ip:nn formatext-comm-rt-aa4nn2
RT extcommunity in aa:nn formatext-comm-rt-aa2nn4
Command Mode
• /exec/configure/evpn/evi
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3764
R Commandsroute-target import auto
Page 3909
route delete dampen interval[no] route delete dampen interval <time>
Syntax Description
(Optional) Negate a command or set its defaultsno
Display routing informationroute
Dampen route delete update to hardwaredelete
Dampen update to hardwaredampen
Dampen intervalinterval
Dampen interval in secondstime
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3765
R Commandsroute delete dampen interval
Page 3910
router-guard ip multicast[no] router-guard ip multicast [ vlan <vlan_id> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configures router guard for all interfacesrouter-guard
Configure IP featuresip
router-guard for multicast packet processingmulticast
(Optional) Configures router guard for specified vlan only(only in trunkports)
vlan
(Optional) Specify vlan-idvlan_id
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3766
R Commandsrouter-guard ip multicast
Page 3911
router-guard ip multicast switchports[no] router-guard ip multicast switchports
Syntax Description
(Optional) Negate a command or set its defaultsno
Configures router guard for all interfacesrouter-guard
Configure IP featuresip
router-guard for multicast packet processingmulticast
configures on all switchports globallyswitchports
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3767
R Commandsrouter-guard ip multicast switchports
Page 3912
router-id[no] router-id { <interface> | <rid> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Router-IDrouter-id
Interface to provide IP address for router-idinterface
IP address to become router-idrid
Command Mode
• /exec/configure/router-isis/router-isis-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3768
R Commandsrouter-id
Page 3913
router-id{ { router-id <id> } | { no router-id [ <id> ] } }
Syntax Description
Negate a command or set its defaultsno
Set OSPFv3 process router-idrouter-id
Router ID Valueid
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3769
R Commandsrouter-id
Page 3914
router-id{ { [ eigrp ] router-id <id> } | { no [ eigrp ] router-id [ <id> ] } }
Syntax Description
Negate a command or set its defaultsno
(Optional) EIGRP router configuration commandseigrp
router-id for this EIGRP processrouter-id
EIGRP Router-ID in IP address formatid
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3770
R Commandsrouter-id
Page 3915
router-id{ { router-id <id> } | { no router-id [ <id> ] } }
Syntax Description
Negate a command or set its defaultsno
Set OSPF process router-idrouter-id
Router ID Valueid
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3771
R Commandsrouter-id
Page 3916
router-idrouter-id [ vrf { <vrf-name> | <vrf-known-name> } ] <interface> [ force ] | no router-id [ { vrf { <vrf-name>| <vrf-known-name> } | <interface> [ force ] } ]
Syntax Description
Negate a command or set its defaultsno
Select interface to prefer for LDP identifier addressrouter-id
(Optional) VRF Routing/Forwarding instance informationvrf
(Optional) VPN Routing/Forwarding instance namevrf-name
(Optional) Known VRF namevrf-known-name
interface
(Optional) Forcibly change the LDP router idforce
Command Mode
• /exec/configure/ldp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3772
R Commandsrouter-id
Page 3917
router-id[no] router-id <router-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Specify the IP address to use as router-idrouter-id
Manually configured router identifierrouter-id
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3773
R Commandsrouter-id
Page 3918
router-preference maximum[no] router-preference maximum <prefopts>
Syntax Description
(Optional) Negate a command or set its defaultsno
prefopts
Command Mode
• /exec/configure/config-ra-guard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3774
R Commandsrouter-preference maximum
Page 3919
router bgp[no] router bgp <as>
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable a routing processrouter
Border Gateway Protocol (BGP)bgp
Autonomousas
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3775
R Commandsrouter bgp
Page 3920
router eigrp[no] router eigrp <eigrp-ptag>
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable a routing processrouter
Enhanced Interior Gateway Routing Protocol (EIGRP)eigrp
Process tageigrp-ptag
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3776
R Commandsrouter eigrp
Page 3921
router isis[no] router isis <tag>
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable a routing processrouter
Intermediate System to Intermediate System (IS-IS)isis
Routing process tagtag
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3777
R Commandsrouter isis
Page 3922
router ospf[no] router ospf <tag>
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable a routing processrouter
Open Shortest Path First (OSPF)ospf
Process tagtag
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3778
R Commandsrouter ospf
Page 3923
router ospfv3[no] router ospfv3 <tag>
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable a routing processrouter
Open Shortest Path First (OSPF) (Version 3)ospfv3
Process tagtag
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3779
R Commandsrouter ospfv3
Page 3924
router rip[no] router rip <tag>
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable a routing processrouter
Routing Information Protocol (RIP)rip
Process IDtag
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3780
R Commandsrouter rip
Page 3925
routing-context vrfrouting-context vrf <vrf-known-name>
Syntax Description
Set the routing contextrouting-context
The new routing-context VRFvrf
Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3781
R Commandsrouting-context vrf
Page 3926
rsakeypair[no] rsakeypair <s0> [ <i0> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure trustpoint rsa key-pair detailsrsakeypair
key-pair labels0
(Optional) key-pair sizei0
Command Mode
• /exec/configure/trustpoint
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3782
R Commandsrsakeypair
Page 3927
rtr etr eid[no] { rtr | etr | eid } { <locator> | <locator6> } [ strict | probe ] + <seq>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure RTR in ELP ordered listrtr
Configure ETR in ELP ordered listetr
Configure EID in ELP ordered listeid
IPv4 locator for RTR/ETR or EIDlocator
(Optional) ELP hop must be used in Explicit Locator Pathstrict
(Optional) RLOC-probe next-hop in ELPprobe
Sequence to insert or delete RTR/ETR/EID ELP entryseq
Command Mode
• /exec/configure/lisp-elp /exec/configure/vrf/lisp-elp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3783
R Commandsrtr etr eid
Page 3928
rulerule <number> { <action> } { { <permission> [ <featuretype> <name> ] } } | no rule <number>
Syntax Description
Negate a command or set its defaultsno
Enter the rule numberrule
Enter the rule numbernumber
Actionaction
Permissionpermission
(Optional) Feature typefeaturetype
(Optional) Enter the access entity namename
Command Mode
• /exec/configure/role
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3784
R Commandsrule
Page 3929
rule commandrule <number> { <action> } { command <cmd_line> } | no rule <number>
Syntax Description
Negate a command or set its defaultsno
Enter the rule numberrule
Enter the rule numbernumber
Actionaction
Command linecommand
Enter the command (use space+' ' for command separator) e.g. config trole *
cmd_line
Command Mode
• /exec/configure/role
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3785
R Commandsrule command
Page 3930
rule oidrule <number> <action> <permission> oid <snmp_oid> | no rule <number>
Syntax Description
Negate a command or set its defaultsno
Enter the rule numberrule
Enter the rule numbernumber
Actionaction
Permissionpermission
SNMP oid (up to 32 elements)oid
Enter snmp oid instance namesnmp_oid
Command Mode
• /exec/configure/role
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3786
R Commandsrule oid
Page 3931
run-scriptrun-script <uri0>
Syntax Description
Run shell scriptsrun-script
Enter script file nameuri0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3787
R Commandsrun-script
Page 3932
run2 guestshellrun2 guestshell [ { <cmd_args> } ]
Syntax Description
execute/run programrun2
The guest shell Linux-bashguestshell
(Optional) The command to executecmd_args
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3788
R Commandsrun2 guestshell
Page 3933
run bashrun bash [ <cmd> ]
Syntax Description
execute/run programrun
linux-bashbash
(Optional) the command to executecmd
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3789
R Commandsrun bash
Page 3934
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3790
R Commandsrun bash
Page 3935
S Commands
• sak-expiry-time, on page 3805• sampling-rate prepost, on page 3806• sampling, on page 3807• sap hash-algorithm HMAC-SHA-1, on page 3808• sap modelist, on page 3809• sap pmk sap pmk use-dot1x, on page 3810• save, on page 3811• scale-factor module, on page 3812• scheduler aaa-authentication, on page 3813• scheduler enable, on page 3814• scheduler job name, on page 3815• scheduler logfile size, on page 3816• scheduler schedule name, on page 3817• scheduler transport email, on page 3818• scripting tcl init, on page 3819• scripting tcl recursion-limit, on page 3820• section, on page 3821• secure-handoff, on page 3822• security-level, on page 3823• security-policy, on page 3824• sed, on page 3825• send-community, on page 3826• send-community, on page 3827• send-community extended, on page 3828• send-lifetimemonth_amonth_bmonth_cmonth_dmonth_emonth_fmonth_gmonth_hmonth_i month_jmonth_k month_l duration infinite month_a month_b month_c month_d month_e month_f month_gmonth_h month_i month_j month_k month_l, on page 3829
• send-lifetimemonth_amonth_bmonth_cmonth_dmonth_emonth_fmonth_gmonth_hmonth_i month_jmonth_k month_l duration infinite month_a month_b month_c month_d month_e month_f month_gmonth_h month_i month_j month_k month_l, on page 3831
• send, on page 3833• send session, on page 3834• sender, on page 3835• sensor-group, on page 3836
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3791
Page 3936
• server, on page 3837• server, on page 3838• server, on page 3839• server protocol ldap, on page 3840• server protocol radius group, on page 3841• server protocol xmpp ip, on page 3842• service-policy-dynamic input, on page 3843• service-policy, on page 3844• service-policy, on page 3845• service-policy, on page 3846• service-policy input, on page 3847• service-policy type network-qos, on page 3848• service-policy type qos, on page 3849• service-policy type queuing, on page 3850• service-policy type queuing, on page 3851• service-policy type queuing, on page 3852• service password-recovery, on page 3853• service unsupported-transceiver, on page 3854• session-limit, on page 3855• session domain-lookup, on page 3856• session protection, on page 3857• set-attached-bit, on page 3858• set-overload-bit, on page 3859• set-overload-bit, on page 3860• set, on page 3861• set, on page 3864• set, on page 3865• set, on page 3866• set, on page 3867• set, on page 3869• set as-path prepend last-as tag, on page 3870• set comm-list delete, on page 3871• set community none additive internet local-AS, on page 3872• set cos, on page 3873• set cos, on page 3874• set dampening, on page 3875• set distance, on page 3876• set drpvec, on page 3877• set drpvec, on page 3883• set extcomm-list delete, on page 3889• set extcommunity 4byteas-generic transitive additive, on page 3890• set extcommunity color, on page 3891• set extcommunity cost, on page 3892• set extcommunity rt additive, on page 3893• set forwarding-address, on page 3894• set ieth, on page 3895
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3792
S Commands
Page 3937
• set ieth, on page 3898• set inner arp, on page 3901• set inner ipv4, on page 3903• set inner ipv4, on page 3905• set inner ipv4, on page 3907• set inner ipv6 src_ip, on page 3909• set inner l2, on page 3910• set inner l2, on page 3912• set inner l2, on page 3914• set inner l2 hg2, on page 3916• set inner l2 hg2, on page 3918• set inner l4, on page 3920• set inner l4, on page 3921• set inner l4, on page 3924• set interface, on page 3925• set interval find-new-host, on page 3926• set interval sync-full-info, on page 3927• set ip address prefix-list, on page 3928• set ip default next-hop, on page 3929• set ip default next-hop verify-availability, on page 3930• set ip next-hop, on page 3931• set ip next-hop peer-address, on page 3932• set ip next-hop redist-unchanged, on page 3933• set ip next-hop unchanged, on page 3934• set ip next-hop verify-availability, on page 3935• set ip precedence, on page 3936• set ipv6 address prefix-list, on page 3937• set ipv6 default next-hop, on page 3938• set ipv6 default next-hop verify-availability, on page 3939• set ipv6 next-hop, on page 3940• set ipv6 next-hop peer-address, on page 3941• set ipv6 next-hop redist-unchanged, on page 3942• set ipv6 next-hop unchanged, on page 3943• set ipv6 next-hop verify-availability, on page 3944• set ipv6 precedence, on page 3945• set label-index, on page 3946• set level level-1 level-1-2 level-2, on page 3947• set local-preference, on page 3948• set metric, on page 3949• set nssa-only, on page 3950• set origin egp, on page 3951• set origin egp igp incomplete, on page 3952• set outer arp, on page 3953• set outer arp, on page 3955• set outer fcoe, on page 3957• set outer ipv4, on page 3959
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3793
S Commands
Page 3938
• set outer ipv4, on page 3961• set outer ipv4, on page 3963• set outer ipv6 src_ip, on page 3965• set outer ipv6 src_ip, on page 3966• set outer l2, on page 3967• set outer l2, on page 3969• set outer l2, on page 3971• set outer l2 hg2, on page 3973• set outer l4, on page 3975• set outer l4, on page 3976• set outer l4, on page 3979• set path-selection advertise, on page 3982• set pktrw, on page 3983• set pktrw, on page 3990• set pktrw, on page 3997• set sb_info, on page 4003• set sb_info, on page 4006• set sideband, on page 4009• set sideband, on page 4011• set sideband, on page 4013• set sideband, on page 4015• set stats, on page 4018• set tag, on page 4021• set weight, on page 4022• setup, on page 4023• sflow, on page 4024• sflow, on page 4025• sflow data-source interface, on page 4026• sflow data-source interface, on page 4027• sflow extended switch, on page 4028• shape, on page 4029• shared-secret, on page 4031• shut, on page 4032• shutdown, on page 4033• shutdown, on page 4034• shutdown, on page 4035• shutdown, on page 4036• shutdown, on page 4037• shutdown, on page 4038• shutdown, on page 4039• shutdown, on page 4040• shutdown, on page 4041• shutdown, on page 4042• shutdown, on page 4043• shutdown, on page 4044• shutdown, on page 4045
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3794
S Commands
Page 3939
• shutdown, on page 4046• shutdown, on page 4047• shutdown, on page 4048• shutdown, on page 4049• shutdown, on page 4050• shutdown, on page 4051• shutdown, on page 4052• shutdown, on page 4053• shutdown, on page 4054• shutdown, on page 4055• shutdown, on page 4056• shutdown, on page 4057• shutdown, on page 4058• shutdown, on page 4059• shutdown, on page 4060• shutdown, on page 4061• shutdown, on page 4062• shutdown, on page 4063• shutdown, on page 4064• shutdown, on page 4065• shutdown, on page 4066• shutdown, on page 4067• shutdown, on page 4068• shutdown, on page 4069• shutdown, on page 4070• shutdown force, on page 4071• shutdown lan, on page 4072• shutdown lan, on page 4073• signalling advertise explicit-null, on page 4074• signalling hello graceful-restart, on page 4075• signalling hello graceful-restart refresh interval, on page 4076• signalling hello graceful-restart refresh misses, on page 4077• signalling hello graceful-restart send recovery-time, on page 4078• signalling hello graceful-restart send restart-time, on page 4079• signalling hello reroute, on page 4080• signalling initial-retransmit-delay, on page 4081• signalling patherr state-removal, on page 4082• signalling rate-limit, on page 4083• signalling refresh interval, on page 4084• signalling refresh misses, on page 4085• signalling refresh reduction, on page 4086• signalling refresh reduction ack-delay, on page 4087• signalling refresh reduction bundle-max-size, on page 4088• signing level, on page 4089• site-id, on page 4090• site-of-origin, on page 4091
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3795
S Commands
Page 3940
• slave ipv4, on page 4092• sleep, on page 4093• sleep instance, on page 4094• slot, on page 4095• slot, on page 4096• smart-channel, on page 4097• smart-channel port-group, on page 4098• smtp-host smtp-port reply-to from, on page 4099• snapshot create, on page 4100• snapshot delete, on page 4101• snapshot delete ALL, on page 4102• snapshot section add, on page 4103• snapshot section delete, on page 4104• snmp-server aaa-user cache-timeout, on page 4105• snmp-server community, on page 4106• snmp-server community, on page 4107• snmp-server community use-acl, on page 4108• snmp-server contact, on page 4109• snmp-server context, on page 4110• snmp-server counter cache enable, on page 4111• snmp-server counter cache timeout, on page 4112• snmp-server enable traps, on page 4113• snmp-server enable traps bgp, on page 4114• snmp-server enable traps bgp cbgp2, on page 4115• snmp-server enable traps bgp cbgp2 threshold prefix, on page 4116• snmp-server enable traps bgp threshold prefix, on page 4117• snmp-server enable traps eigrp, on page 4118• snmp-server enable traps ospf, on page 4119• snmp-server enable traps ospf lsa, on page 4120• snmp-server enable traps ospf rate-limit, on page 4121• snmp-server enable traps ospfv3, on page 4122• snmp-server enable traps ospfv3 lsa, on page 4123• snmp-server enable traps ospfv3 lsa, on page 4124• snmp-server enable traps ospfv3 rate-limit, on page 4125• snmp-server enable traps storm-control trap-rate, on page 4126• snmp-server engineID local, on page 4127• snmp-server force-unload-feature, on page 4128• snmp-server globalEnforcePriv, on page 4129• snmp-server host, on page 4130• snmp-server host filter-vrf, on page 4131• snmp-server host source, on page 4132• snmp-server host use-vrf, on page 4133• snmp-server host use_vrf, on page 4134• snmp-server load-cond-feature, on page 4135• snmp-server load-mib, on page 4136• snmp-server location, on page 4137
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3796
S Commands
Page 3941
• snmp-server mib community-map context, on page 4138• snmp-server protocol enable, on page 4139• snmp-server source-interface informs, on page 4140• snmp-server source-interface traps, on page 4141• snmp-server system-shutdown, on page 4142• snmp-server tcp-session, on page 4143• snmp-server user, on page 4144• snmp-server user, on page 4145• snmp ifmib ifalias long, on page 4147• snmp trap link-status, on page 4148• snmp trap link-status, on page 4149• snmp trap link-status, on page 4150• snmp trap link-status, on page 4151• snmp trap link-status, on page 4152• snmp trap link-status, on page 4153• snsr-grp sample-interval, on page 4154• sockets local-port-range, on page 4155• soft-reconfiguration inbound, on page 4156• soft-reconfiguration inbound, on page 4157• soo auto, on page 4158• sort, on page 4159• source-address ipv4, on page 4160• source-group, on page 4161• source-interface, on page 4162• source-interface, on page 4163• source-interface, on page 4164• source-interface, on page 4165• source-interface, on page 4166• source-interface, on page 4167• source-interface hold-down-time, on page 4168• source, on page 4169• source, on page 4170• source, on page 4171• source, on page 4172• source, on page 4173• source, on page 4174• source, on page 4175• source, on page 4176• source, on page 4177• source, on page 4178• source, on page 4179• source copy-sys, on page 4180• source filter ip, on page 4181• source filter ip any any, on page 4182• source forward-drops, on page 4183• source group permit, on page 4184
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3797
S Commands
Page 3942
• source interface, on page 4185• source interface, on page 4186• source ip, on page 4187• source vlan, on page 4188• spanning-tree bpdufilter, on page 4189• spanning-tree bpduguard, on page 4190• spanning-tree bridge-domain, on page 4191• spanning-tree bridge assurance, on page 4192• spanning-tree cost, on page 4193• spanning-tree cost auto, on page 4194• spanning-tree domain, on page 4195• spanning-tree domain clear statistics, on page 4196• spanning-tree fcoe, on page 4197• spanning-tree guard, on page 4198• spanning-tree lc-issu, on page 4199• spanning-tree lc-issu, on page 4200• spanning-tree link-type, on page 4201• spanning-tree loopguard default, on page 4202• spanning-tree mode, on page 4203• spanning-tree mst configuration, on page 4204• spanning-tree mst configuration, on page 4205• spanning-tree mst cost, on page 4206• spanning-tree mst cost auto, on page 4207• spanning-tree mst forward-time, on page 4208• spanning-tree mst hello-time, on page 4209• spanning-tree mst max-age, on page 4210• spanning-tree mst max-hops, on page 4211• spanning-tree mst port-priority, on page 4212• spanning-tree mst pre-standard, on page 4213• spanning-tree mst priority, on page 4214• spanning-tree mst root, on page 4215• spanning-tree mst simulate pvst, on page 4216• spanning-tree mst simulate pvst global, on page 4217• spanning-tree pathcost method, on page 4218• spanning-tree port-priority, on page 4219• spanning-tree port type, on page 4220• spanning-tree port type edge bpdufilter default, on page 4221• spanning-tree port type edge bpduguard default, on page 4222• spanning-tree port type edge default, on page 4223• spanning-tree port type edge trunk, on page 4224• spanning-tree port type network default, on page 4225• spanning-tree pseudo-information, on page 4226• spanning-tree vlan, on page 4227• spanning-tree vlan forward-time, on page 4228• spanning-tree vlan hello-time, on page 4229• spanning-tree vlan max-age, on page 4230
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3798
S Commands
Page 3943
• spanning-tree vlan priority, on page 4231• spanning-tree vlan root, on page 4232• speed-group, on page 4233• speed, on page 4234• speed, on page 4235• speed, on page 4236• speed, on page 4237• speed, on page 4238• speed, on page 4239• speed, on page 4240• speed, on page 4241• speed auto, on page 4242• speed auto 100, on page 4243• speed auto 100 1000, on page 4244• speed auto 100 1000, on page 4245• speed auto 100, on page 4246• speed auto, on page 4247• spf-interval, on page 4248• spf-interval, on page 4249• spf-interval, on page 4250• spf mode incremental, on page 4251• sport, on page 4252• sport, on page 4253• src-intf, on page 4254• ssh, on page 4255• ssh6, on page 4256• ssh all, on page 4257• ssh cipher-mode weak, on page 4258• ssh idle, on page 4259• ssh key, on page 4260• ssh login-attempts, on page 4261• ssh login-gracetime, on page 4262• ssh port, on page 4263• ssh rekey max-data max-time, on page 4264• ssh server enable, on page 4265• ssx exporter, on page 4266• ssx monitor, on page 4267• ssx record, on page 4268• ssx system monitor, on page 4269• ssx system system-id, on page 4270• standby, on page 4271• standby ip, on page 4272• start-threshold, on page 4273• start, on page 4274• start, on page 4275• start, on page 4276
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3799
S Commands
Page 3944
• start, on page 4277• start, on page 4278• start, on page 4279• start, on page 4280• start, on page 4281• start, on page 4282• start, on page 4283• start, on page 4284• start, on page 4285• start, on page 4286• start, on page 4287• start, on page 4288• start, on page 4289• state, on page 4290• state enabled, on page 4291• statistics, on page 4292• statistics, on page 4293• statistics, on page 4294• statistics collection-interval, on page 4295• statistics per-entry, on page 4296• statistics per-entry, on page 4297• statistics per-entry, on page 4298• statistics per-entry, on page 4299• stats-reporting-period, on page 4300• status, on page 4301• status, on page 4302• status, on page 4303• status, on page 4304• status, on page 4305• status, on page 4306• status, on page 4307• stop-threshold, on page 4308• stopbits, on page 4309• stopbits 1, on page 4310• storm-control-cpu, on page 4311• storm-control, on page 4312• streetaddress, on page 4313• stub, on page 4314• sub-switch vlan, on page 4315• subscription, on page 4316• summary-address, on page 4317• summary-address, on page 4318• summary-address, on page 4319• summary-address, on page 4320• suppress-arp, on page 4321• suppress-fib-pending, on page 4322
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3800
S Commands
Page 3945
• suppress-fib-pending, on page 4323• suppress-inactive, on page 4324• suppress-inactive, on page 4325• suppress-signaling-protocol ldp, on page 4326• suppress mac-route, on page 4327• switch-id, on page 4328• switch-priority, on page 4329• switch-profile, on page 4330• switch-profile, on page 4331• switch-role border-leaf, on page 4332• switch-scope controller, on page 4333• switch pipeline, on page 4334• switchback, on page 4335• switching-mode fabric-speed 40g, on page 4336• switching-mode fast-to-slow-speed-cut-through, on page 4337• switching-mode store-forward, on page 4338• switchport, on page 4339• switchport, on page 4340• switchport access vlan, on page 4341• switchport access vlan, on page 4342• switchport access vlan, on page 4343• switchport autostate exclude, on page 4344• switchport backup interface, on page 4345• switchport backup interface, on page 4346• switchport backup interface multicast fast-convergence, on page 4347• switchport backup interface multicast fast-convergence, on page 4348• switchport backup interface preemption delay, on page 4349• switchport backup interface preemption delay, on page 4350• switchport backup interface preemption mode, on page 4351• switchport backup interface preemption mode, on page 4352• switchport beacon, on page 4353• switchport block unicast, on page 4354• switchport description, on page 4355• switchport dot1q ethertype, on page 4356• switchport dot1q ethertype, on page 4357• switchport duplex, on page 4358• switchport host, on page 4359• switchport ignore bit-errors, on page 4360• switchport isolated, on page 4361• switchport mac-learn disable, on page 4362• switchport mode, on page 4363• switchport mode, on page 4364• switchport mode, on page 4365• switchport mode, on page 4366• switchport mode, on page 4367• switchport mode, on page 4368
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3801
S Commands
Page 3946
• switchport mode monitor buffer-limit, on page 4369• switchport mode private-vlan, on page 4370• switchport mode private-vlan trunk, on page 4371• switchport monitor, on page 4372• switchport mtu, on page 4373• switchport owner, on page 4374• switchport port-security, on page 4375• switchport port-security aging time, on page 4376• switchport port-security aging type absolute, on page 4377• switchport port-security mac-address, on page 4378• switchport port-security mac-address sticky, on page 4379• switchport port-security maximum, on page 4380• switchport port-security violation, on page 4381• switchport priority extend cos, on page 4382• switchport private-vlan association trunk, on page 4383• switchport private-vlan host-association, on page 4384• switchport private-vlan mapping, on page 4385• switchport private-vlan mapping trunk, on page 4386• switchport private-vlan trunk allowed vlan, on page 4387• switchport private-vlan trunk native vlan, on page 4388• switchport promiscuous-mode off, on page 4389• switchport speed, on page 4390• switchport speed, on page 4391• switchport trunk allow-multi-tag, on page 4392• switchport trunk allowed vlan, on page 4393• switchport trunk allowed vsan, on page 4394• switchport trunk allowed vsan, on page 4395• switchport trunk mode, on page 4396• switchport trunk mode, on page 4397• switchport trunk native vlan, on page 4398• switchport trunk pruning vlan except add remove none all, on page 4399• switchport virtual-ethernet-bridge, on page 4400• switchport vlan mapping, on page 4401• switchport vlan mapping all, on page 4402• switchport vlan mapping all dot1q-tunnel, on page 4403• switchport vlan mapping all dot1q-tunnel, on page 4404• switchport vlan mapping dot1q-tunnel, on page 4405• switchport vlan mapping dot1q-tunnel allowed-vlan, on page 4406• switchport vlan mapping enable, on page 4407• switchport voice vlan, on page 4408• switchport voice vlan, on page 4409• switchto vdc, on page 4410• sync-peers destination, on page 4411• sync-snmp-password, on page 4412• sync-snmp-password, on page 4413• sync-snmp-password, on page 4414
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3802
S Commands
Page 3947
• system-mac, on page 4415• system-mac, on page 4416• system-priority, on page 4417• system, on page 4418• system, on page 4419• system acl, on page 4421• system auto-collect tech-support, on page 4422• system cores, on page 4423• system default interface-vlan autostate, on page 4424• system default interface, on page 4425• system default interface, on page 4426• system default switchport, on page 4427• system default switchport shutdown, on page 4428• system default tx-credit double-queue, on page 4429• system dot1q-tunnel transit, on page 4430• system fabric-mode full-rate, on page 4431• system fabric core-vlans, on page 4432• system fabric dynamic-vlans, on page 4433• system fast-reload stabilization-timer, on page 4434• system hap-reset, on page 4435• system hap-reset, on page 4436• system health check bootflash, on page 4437• system heartbeat, on page 4438• system heartbeat, on page 4439• system high-multicast-priority, on page 4440• system inband queuing, on page 4441• system inband queuing, on page 4442• system interface shutdown, on page 4443• system jumbomtu, on page 4444• system kgdb, on page 4445• system kgdb, on page 4446• system login block-for, on page 4447• system login block-for attempts within, on page 4448• system login quiet-mode, on page 4449• system login quiet-mode access-class, on page 4450• system memory-thresholds minor severe critical, on page 4451• system mode maintenance, on page 4452• system mode maintenance always-use-custom-profile, on page 4453• system mode maintenance maint-delay, on page 4454• system mode maintenance on-reload reset-reason, on page 4455• system mode maintenance snapshot-delay, on page 4456• system mode maintenance timeout, on page 4457• system module emon-enhanced, on page 4458• system module failure-action shutdown, on page 4459• system mrouting, on page 4460• system poap, on page 4461
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3803
S Commands
Page 3948
• system poap, on page 4462• system pss shrink, on page 4463• system qos, on page 4464• system routing unknown-unicast-flood, on page 4465• system security compliance common-criteria, on page 4466• system shutdown fan-direction mismatch, on page 4467• system simulate fan-presence, on page 4468• system standby manual-boot, on page 4469• system standby manual-boot, on page 4470• system startup-config init, on page 4471• system startup-config unlock, on page 4472• system statistics, on page 4473• system statistics, on page 4474• system switch-mode, on page 4475• system switchover, on page 4476• system switchover force, on page 4477• system timeout, on page 4478• system trace, on page 4479• system urpf disable, on page 4480• system vlan long-name, on page 4481• system vlan reserve, on page 4482• system vrf-member-change retain-l3-config, on page 4483• system watchdog, on page 4484• system watchdog, on page 4485• system watchdog kgdb, on page 4486• system watchdog kgdb, on page 4487
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3804
S Commands
Page 3949
sak-expiry-time[no] sak-expiry-time <ts>
Syntax Description
Time in seconds to force SAK rekeysak-expiry-time
time in secondsts
Command Mode
• /exec/configure/macsec-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3805
S Commandssak-expiry-time
Page 3950
sampling-rate prepost[no] sampling-rate { pre-trigger <pre-sample-rate> } { post-trigger <post-sample-rate> }
Syntax Description
(Optional) Negate the commandno
Configure sampling-rate parameterssampling-rate
Pre-trigger parameterspre-trigger
Transactions to be captured out of 16 samples (1-16)pre-sample-rate
Post-trigger parameterspost-trigger
Transactions to be captured out of 16 samples (1-16)post-sample-rate
Command Mode
• /exec/configure/pkt-drop
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3806
S Commandssampling-rate prepost
Page 3951
samplingsampling <sampling_range> | no sampling
Syntax Description
Negate a command or set its defaultsno
Set the sampling range for SPAN packets.sampling
Sampling range: N = every Nth packet will be spannedsampling_range
Command Mode
• /exec/configure/monitor-local-src /exec/configure/config-monitor/exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3807
S Commandssampling
Page 3952
sap hash-algorithm HMAC-SHA-1{ [ no ] sap hash-algorithm HMAC-SHA-1 } | { sap hash-algorithm HMAC-MD5 }
Syntax Description
Specify preferred SAP negotiation parameterssap
Hashing Algorithm to use during SAP protocolhash-algorithm
use HMAC-SHA-1 for hashing (default is HMAC-MD5)HMAC-SHA-1
use HMAC-MD5 for hashingHMAC-MD5
Command Mode
• /exec/configure/cts-dot1x /exec/configure/cts-manual
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3808
S Commandssap hash-algorithm HMAC-SHA-1
Page 3953
sap modelist[no] sap modelist <mode_opt>
Syntax Description
Specify preferred SAP negotiation parameterssap
encryption modemodelist
modelist optionsmode_opt
Command Mode
• /exec/configure/cts-dot1x
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3809
S Commandssap modelist
Page 3954
sap pmk sap pmk use-dot1xsap pmk <pmk> [ left-zero-padded ] [ modelist <mode_opt> ] | sap pmk use-dot1x [ modelist <mode_opt> ]| no sap
Syntax Description
Specify preferred SAP negotiation parameterssap
pairwise master keypmk
32 byte value specified as a stringpmk
(Optional) Pad with zeros on the left if PMK length is less than 32 bytesleft-zero-padded
(Optional) encryption modemodelist
(Optional) modelist optionsmode_opt
(Optional) <mode_opt>modelist
Use pmk generated after dot1x authentication. Use dot1x commands toconfigure dot1x on this port
use-dot1x
Command Mode
• /exec/configure/cts-manual
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3810
S Commandssap pmk sap pmk use-dot1x
Page 3955
savesave <uri0>
Syntax Description
Save the current configuration session to urisave
Enter the complete uri where the session is to be storeduri0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3811
S Commandssave
Page 3956
scale-factor module[no] scale-factor <sf-value> module <module-number>
Syntax Description
(Optional) Negate a command or set its defaultsno
Scale factorscale-factor
Specify scale factor value from 0.10 to 2.00sf-value
Modulemodule
specify module numbermodule-number
Command Mode
• /exec/configure/ctrl-plane
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3812
S Commandsscale-factor module
Page 3957
scheduler aaa-authentication{ scheduler aaa-authentication { password { 0 <s0> | 7 <s1> | <s2> } | username <s3> password { 01 <s4> |71 <s5> | <s6> } } | no scheduler aaa-authentication { password [ { 0 <s0> | 7 <s1> | <s2> } ] | username <s3>password [ { 01 <s4> | 71 <s5> | <s6> } ] } }
Syntax Description
Negate a command or set its defaultsno
Config commands for schedulerscheduler
Password for AAA authentication(of logged in user)aaa-authentication
Specify the password of logged in user(for AAA authentication)password
Password (clear text) of logged in user0
password (clear text) of logged in users0
Encrypted password of logged in user7
Encrypted password (for AAA authentication)s1
Password (clear text) of logged in users2
logged in user nameusername
user name (for AAA authentication)s3
Specify the password of logged in user(for AAA authentication)password
Password (clear text) of logged in user01
password (clear text) of logged in users4
Encrypted password of logged in user71
Encrypted password (for AAA authentication)s5
Password (clear text) of logged in users6
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3813
S Commandsscheduler aaa-authentication
Page 3958
scheduler enable[no] scheduler enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Config commands for schedulerscheduler
Command to enable/disable featuresenable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3814
S Commandsscheduler enable
Page 3959
scheduler job name[no] scheduler job name <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Config commands for schedulerscheduler
Define a jobjob
Specify a name for the jobname
Name of the jobs0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3815
S Commandsscheduler job name
Page 3960
scheduler logfile size{ scheduler logfile size <i0> | no scheduler logfile size [ <i0> ] }
Syntax Description
Negate a command or set its defaultsno
Config commands for schedulerscheduler
Scheduler log file configurationlogfile
Specify the log file sizesize
Size of the file in KBi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3816
S Commandsscheduler logfile size
Page 3961
scheduler schedule name[no] scheduler schedule name <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Config commands for schedulerscheduler
Define a scheduleschedule
Specify a name for the schedulename
Name of the schedules0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3817
S Commandsscheduler schedule name
Page 3962
scheduler transport email{ scheduler transport email { from <s0> | reply-to <s1> | smtp-server <host0> [ port <i1> ] } | no schedulertransport email { from | reply-to | smtp-server } }
Syntax Description
Negate a command or set its defaultsno
Config commands for schedulerscheduler
Configure transport related configurationtransport
Configure email transport related configurationemail
Configure from email addressfrom
Provide from email address, example: [email protected]
Configure replyto email addressreply-to
Provide reply-to email address, example: [email protected]
Configure SMTP server addresssmtp-server
SMTP server(DNS name or IPv4 or IPv6 address)host0
(Optional) Configure SMTP server port (default:25)port
(Optional) SMTP server porti1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3818
S Commandsscheduler transport email
Page 3963
scripting tcl initscripting tcl init <uri0> | no scripting tcl init
Syntax Description
Negate a command or set its defaultsno
Configure scripting parametersscripting
Specify scripting parameter for tcltcl
Specify init parametersinit
Tcl init script nameuri0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3819
S Commandsscripting tcl init
Page 3964
scripting tcl recursion-limitscripting tcl recursion-limit <limit> | no scripting tcl recursion-limit
Syntax Description
Negate a command or set its defaultsno
Configure scripting parametersscripting
Specify scripting parameter for tcltcl
Specify recursion-limitrecursion-limit
Specify limitlimit
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3820
S Commandsscripting tcl recursion-limit
Page 3965
section| section <pattern>
Syntax Description
Pipe command output to filter|
show lines that include the pattern as well as the subsequent lines thatare more indented than matching line
section
the pattern (regular expression) to matchpattern
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3821
S Commandssection
Page 3966
secure-handoff{ [ no ] secure-handoff }
Syntax Description
(Optional) Negate a command or set its defaultsno
Confirm dynamic-eid discovery by probing for remote hostsecure-handoff
Command Mode
• /exec/configure/lisp-dynamic-eid /exec/configure/vrf/lisp-dynamic-eid
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3822
S Commandssecure-handoff
Page 3967
security-level[no] security-level <seclvl>
Syntax Description
(Optional) Negate a command or set its defaultsno
seclvl
Command Mode
• /exec/configure/config-snoop-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3823
S Commandssecurity-level
Page 3968
security-policy[no] security-policy <policy>
Syntax Description
Configure Security policysecurity-policy
Security Policy optionspolicy
Command Mode
• /exec/configure/macsec-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3824
S Commandssecurity-policy
Page 3969
sed| sed [ -n ] + <expr>
Syntax Description
Pipe command output to filter|
Stream Editorsed
(Optional) suppress automatic printing of pattern space-n
Edition command (script)expr
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3825
S Commandssed
Page 3970
send-community[ no | default ] send-community [ both | standard ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Send Community attribute to this neighborsend-community
(Optional) Send Standard and Extended Community attributesboth
(Optional) Send Standard Community attributestandard
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-link-state/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3826
S Commandssend-community
Page 3971
send-community[ no | default ] send-community [ both | extended | standard ]
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Send Community attribute to this neighborsend-community
(Optional) Send Standard and Extended Community attributesboth
(Optional) Send Extended Community attributeextended
(Optional) Send Standard Community attributestandard
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3827
S Commandssend-community
Page 3972
send-community extended[ no | default ] send-community extended
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Send Community attribute to this neighborsend-community
Send Extended Community attributeextended
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-evpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-link-state/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3828
S Commandssend-community extended
Page 3973
send-lifetime month_a month_b month_c month_d month_emonth_f month_g month_h month_i month_j month_k month_lduration infinite month_a month_b month_c month_d month_emonth_f month_g month_h month_i month_j month_k month_l
{ { send-lifetime [ local ] <stime> { month_a | month_b | month_c | month_d | month_e | month_f | month_g| month_h | month_i | month_j | month_k | month_l } <sday> <syear> { duration <dsec> | infinite | <etime>{ month_a | month_b | month_c | month_d | month_e | month_f | month_g | month_h | month_i | month_j |month_k | month_l } <eday> <eyear> } } | { no send-lifetime [ [ local ] <stime> {month_a | month_b | month_c| month_d | month_e | month_f | month_g | month_h | month_i | month_j | month_k | month_l } <sday> <syear>{ duration <dsec> | infinite | <etime> {month_a | month_b | month_c | month_d | month_e | month_f | month_g| month_h | month_i | month_j | month_k | month_l } <eday> <eyear> } ] } }
Syntax Description
Negate a command or set its defaultsno
Set send lifetime of macsec keysend-lifetime
(Optional) Specify time in local timezonelocal
HH:MM:SS Time to start <0-23>:<0-59>:<0-59>stime
HH:MM:SS Time to end <0-23>:<0-59>:<0-59>etime
month_a
month_b
month_c
month_d
month_e
month_f
month_g
month_h
month_i
month_j
month_k
month_l
Day of the month to startsday
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3829
S Commandssend-lifetime month_a month_b month_c month_d month_e month_f month_g month_h month_i month_j month_k month_l duration infinite month_a month_b
month_c month_d month_e month_f month_g month_h month_i month_j month_k month_l
Page 3974
Day of the month to endeday
Year to startsyear
Year to endeyear
Set key lifetime durationduration
Duration in secondsdsec
Never Expiresinfinite
Command Mode
• /exec/configure/macseckeychain-key
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3830
S Commandssend-lifetime month_a month_b month_c month_d month_e month_f month_g month_h month_i month_j month_k month_l duration infinite month_a month_bmonth_c month_d month_e month_f month_g month_h month_i month_j month_k month_l
Page 3975
send-lifetime month_a month_b month_c month_d month_emonth_f month_g month_h month_i month_j month_k month_lduration infinite month_a month_b month_c month_d month_emonth_f month_g month_h month_i month_j month_k month_l
{ { send-lifetime [ local ] <stime> { month_a | month_b | month_c | month_d | month_e | month_f | month_g| month_h | month_i | month_j | month_k | month_l } <sday> <syear> { duration <dsec> | infinite | <etime>{ month_a | month_b | month_c | month_d | month_e | month_f | month_g | month_h | month_i | month_j |month_k | month_l } <eday> <eyear> } } | { no send-lifetime [ [ local ] <stime> {month_a | month_b | month_c| month_d | month_e | month_f | month_g | month_h | month_i | month_j | month_k | month_l } <sday> <syear>{ duration <dsec> | infinite | <etime> {month_a | month_b | month_c | month_d | month_e | month_f | month_g| month_h | month_i | month_j | month_k | month_l } <eday> <eyear> } ] } }
Syntax Description
Negate a command or set its defaultsno
Set send lifetime of keysend-lifetime
(Optional) Specify time in local timezonelocal
HH:MM:SS Time to start <0-23>:<0-59>:<0-59>stime
HH:MM:SS Time to end <0-23>:<0-59>:<0-59>etime
month_a
month_b
month_c
month_d
month_e
month_f
month_g
month_h
month_i
month_j
month_k
month_l
Day of the month to startsday
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3831
S Commandssend-lifetime month_a month_b month_c month_d month_e month_f month_g month_h month_i month_j month_k month_l duration infinite month_a month_b
month_c month_d month_e month_f month_g month_h month_i month_j month_k month_l
Page 3976
Day of the month to endeday
Year to startsyear
Year to endeyear
Set key lifetime durationduration
Duration in secondsdsec
Never Expiresinfinite
Command Mode
• /exec/configure/keychain-key
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3832
S Commandssend-lifetime month_a month_b month_c month_d month_e month_f month_g month_h month_i month_j month_k month_l duration infinite month_a month_bmonth_c month_d month_e month_f month_g month_h month_i month_j month_k month_l
Page 3977
sendsend <line>
Syntax Description
Send message to open sessionssend
Send message (a line) to all open sessionsline
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3833
S Commandssend
Page 3978
send sessionsend session <s0> <line>
Syntax Description
Send message to open sessionssend
Send message to specific sessionsession
Specify pts/tty device types0
Enter a one line messageline
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3834
S Commandssend session
Page 3979
sender[no] sender
Syntax Description
(Optional) Negate a command or set its defaultsno
Policies for a Sendersender
Command Mode
• /exec/configure/nbm-host-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3835
S Commandssender
Page 3980
sensor-group[no] sensor-group <sgrp-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Create a sensor groupsensor-group
Identifiersgrp-id
Command Mode
• /exec/configure/telemetry
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3836
S Commandssensor-group
Page 3981
server[no] server { <hostipname> }
Syntax Description
(Optional) Negate a command or set its defaultsno
TACACS+ server name or IP addressserver
IPV4/IPV6 address or DNS namehostipname
Command Mode
• /exec/configure/tacacs+
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3837
S Commandsserver
Page 3982
server[no] server <host0>
Syntax Description
(Optional) Negate a command or set its defaultsno
LDAP server nameserver
LDAP server namehost0
Command Mode
• /exec/configure/ldap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3838
S Commandsserver
Page 3983
server[no] server <hostipname>
Syntax Description
(Optional) Negate a command or set its defaultsno
RADIUS server name or IP addressserver
IPV4/IPV6 address or DNS namehostipname
Command Mode
• /exec/configure/radius
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3839
S Commandsserver
Page 3984
server protocol ldap[no] server protocol ldap { ipv6 <ipv6addr> | ip <ipaddr> | host <hostname> } [ port <portnum> ] [ vrf {<vrf-name> | <vrf-known-name> } ] [ enable-ssl ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure database serverserver
Configure database protocolprotocol
Use LDAPldap
IPv6 address of serveripv6
IP address of serverip
Enter IP address of serveripaddr
Hostname of serverhost
Enter hostname of serverhostname
(Optional) Portport
(Optional) Enter port numberportnum
(Optional) vrf contextvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) LDAP server enable sslenable-ssl
Command Mode
• /exec/configure/fabric-db
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3840
S Commandsserver protocol ldap
Page 3985
server protocol radius group[no] server protocol radius group <groupname>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure database serverserver
Configure database protocolprotocol
Use RADIUSradius
AAA groupgroup
Enter AAA group name of serversgroupname
Command Mode
• /exec/configure/fabric-db
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3841
S Commandsserver protocol radius group
Page 3986
server protocol xmpp ip[no] server protocol xmpp { ip <ipaddr> | host <hostname> } [ port <portnum> ] [ vrf { <vrf-name> |<vrf-known-name> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure database serverserver
Configure database protocolprotocol
Use XMPPxmpp
IP address of serverip
Enter IP address of serveripaddr
Hostname of serverhost
Enter hostname of serverhostname
(Optional) Portport
(Optional) Enter port numberportnum
(Optional) vrf contextvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec/configure/fabric-db
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3842
S Commandsserver protocol xmpp ip
Page 3987
service-policy-dynamic input[no] service-policy-dynamic input <policy_name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Attach a policy to control-plane interfaceservice-policy-dynamic
Input the policy nameinput
Name of the policypolicy_name
Command Mode
• /exec/configure/ctrl-plane-dyn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3843
S Commandsservice-policy-dynamic input
Page 3988
service-policy[no] service-policy [ type qos ] <inp-or-out> <pmap-name-qos> [ no-stats ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure service policy for an interfaceservice-policy
(Optional) Specify the type of this policytype
(Optional) Qos policyqos
inp-or-out
Policy-map name __nil__ You must create a policy-map before usingthis command
pmap-name-qos
(Optional) Disable statistics for this policyno-stats
Command Mode
• /exec/configure/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3844
S Commandsservice-policy
Page 3989
service-policy[no] service-policy [ type qos ] <inp-or-out> <pmap-name-qos> [ no-stats ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure service policy for an interfaceservice-policy
(Optional) Specify the type of this policytype
(Optional) Qos policyqos
inp-or-out
Policy-map name __nil__ You must create a policy-map before usingthis command
pmap-name-qos
(Optional) Disable statistics for this policyno-stats
Command Mode
• /exec/configure/if-set-qos /exec/configure/if-remote-ethernet /exec/configure/if-remote-ethernet-switch/exec/configure/if-fc /exec/configure/if-san-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3845
S Commandsservice-policy
Page 3990
service-policy[no] service-policy [ type qos ] <pmap-name-qos>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure hierarchial policy-mapservice-policy
(Optional) Specify the type of this policytype
(Optional) Qos policyqos
Policy-map namepmap-name-qos
Command Mode
• /exec/configure/policy-map/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3846
S Commandsservice-policy
Page 3991
service-policy input[no] service-policy input <policy_name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Attach a policy to control-plane interfaceservice-policy
Input the policy nameinput
Name of the policypolicy_name
Command Mode
• /exec/configure/ctrl-plane
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3847
S Commandsservice-policy input
Page 3992
service-policy type network-qos[no] service-policy type network-qos <pmap-name-nq>
Syntax Description
(Optional) Negate a command or set its defaultsno
Policy Mapservice-policy
Specify the type of this policy-maptype
Network QoS policynetwork-qos
Policy-map namepmap-name-nq
Command Mode
• /exec/configure/system/qos
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3848
S Commandsservice-policy type network-qos
Page 3993
service-policy type qos[no] service-policy type qos <inp-only> <pmap-name-qos>
Syntax Description
(Optional) Negate a command or set its defaultsno
Policy Mapservice-policy
Specify the type of this policy-maptype
System-level QoS policyqos
inp-only
Policy-map name __nil__ You must create a policy-map before usingthis command
pmap-name-qos
Command Mode
• /exec/configure/system/qos
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3849
S Commandsservice-policy type qos
Page 3994
service-policy type queuing[no] service-policy type queuing <pmap-name-que>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set the inner policy-mapservice-policy
Specify the type of this policytype
Queuing policyqueuing
Policy-map name __nil__ You must create a policy-map before usingthis command
pmap-name-que
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3850
S Commandsservice-policy type queuing
Page 3995
service-policy type queuing[no] service-policy type queuing <inp-or-out> <pmap-name-que> [ no-stats ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure service policy for an interfaceservice-policy
Specify the type of this policytype
Queuing policyqueuing
inp-or-out
Policy-map namepmap-name-que
(Optional) Disable statistics for this policyno-stats
Command Mode
• /exec/configure/if-set-que
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3851
S Commandsservice-policy type queuing
Page 3996
service-policy type queuing[no] service-policy type queuing <inp-or-out> <pmap-name-que>
Syntax Description
(Optional) Negate a command or set its defaultsno
Policy Mapservice-policy
Specify the type of this policy-maptype
DCE Queuing policyqueuing
inp-or-out
Policy-map namepmap-name-que
Command Mode
• /exec/configure/system/qos
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3852
S Commandsservice-policy type queuing
Page 3997
service password-recovery[no] service password-recovery
Syntax Description
(Optional) Negate a command or set its defaultsno
Serviceservice
Configure password-recovery option of consolepassword-recovery
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3853
S Commandsservice password-recovery
Page 3998
service unsupported-transceiver[no] service unsupported-transceiver
Syntax Description
(Optional) Negate a command or set its defaultsno
Serviceability Commandsservice
Configure support for transceivers not supported by Ciscounsupported-transceiver
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3854
S Commandsservice unsupported-transceiver
Page 3999
session-limit[no] session-limit <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set the max no of concurrent vsh sessionssession-limit
Max concurrent vsh sessionsi0
Command Mode
• /exec/configure/line
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3855
S Commandssession-limit
Page 4000
session domain-lookupsession domain-lookup | no session domain-lookup
Syntax Description
Configure session preferencessession
Negate a command or set its defaultsno
Sessiondomain-lookup
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3856
S Commandssession domain-lookup
Page 4001
session protection[no] session protection [ vrf { <vrf-name> | <vrf-known-name> } ] [ for <pfx-list> ] [ duration { <secs> |infinite } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure session parameterssession
Configure session protection parametersprotection
(Optional) VRF Routing/Forwarding instance informationvrf
(Optional) VPN Routing/Forwarding instance namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Prefix list to specify LDP peersfor
(Optional) Prefix list for LDP peerspfx-list
(Optional) Period to sustain session protection after loss of link discoveryduration
(Optional) Holdup time in secondssecs
(Optional) Protect session forever after loss of link discoveryinfinite
Command Mode
• /exec/configure/ldp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3857
S Commandssession protection
Page 4002
set-attached-bit[no] set-attached-bit
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure L1|L2 router to set/unset attached bit in its L1 LSPset-attached-bit
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common /exec/configure/router-isis/router-isis-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3858
S Commandsset-attached-bit
Page 4003
set-overload-bit[no] set-overload-bit | [ no ] set-overload-bit { always | on-startup { <secs> | [ <seconds> ] wait-for bgp <as>} } [ suppress { [ interlevel ] [ external ] } ]
Syntax Description
Negate a command or set its defaultsno
Signal other routers not to use us for transitset-overload-bit
Set the overload bit unconditionallyalways
Set the overload bit on IS-IS startupon-startup
Clear the overload bit after an elapsed time in secondssecs
Clear the overload bit when notified by a specific protocolwait-for
Border Gateway Protocol (BGP)bgp
(Optional) Clear the overload bit after an elapsed time in secondsseconds
Autonomous system numberas
(Optional) Suppress route redistribution if overload bit setsuppress
(Optional) Suppress interlevel route redistributioninterlevel
(Optional) Suppress external route redistributionexternal
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3859
S Commandsset-overload-bit
Page 4004
set-overload-bit{ no set-overload-bit | [ no ] set-overload-bit { always | on-startup { <secs> | <seconds> } } }
Syntax Description
Negate a command or set its defaultsno
Signal other routers not to use us for transitset-overload-bit
Set the overload bit unconditionallyalways
Set the overload bit on IS-IS startupon-startup
Clear the overload bit after an elapsed time in secondssecs
Clear the overload bit after an elapsed time in secondsseconds
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3860
S Commandsset-overload-bit
Page 4005
set[no] set { { cos <cos-val> } | { eth-src-mac-addr <src-mac-addr> } | { eth-dest-mac-addr <dest-mac-addr> }| { vlan <vlan-number> } | { ip-tos <ip-tos-value> <ip-tos-mask> } | { out-interface <iface-list> } | { dscp [tunnel ] { <dscp-val> | <dscp-enum> } } | { precedence [ prec-tunnel ] { <prec-val> | <prec-enum> } } | {discard-class <dis-class-val> } | { qos-group <qos-grp-val> } | { { { cos1 cos2 } | { dscp1 dscp2 } | { prec1prec2 } | { dis-class1 dis-class2 } | { dscp3 mpls-exp-imposition } | { mpls-exp-topmost dscp4 } | {mpls-exp-topmost1 mpls-exp-topmost2 } } } | { mpls experimental { { topmost <exp-value> } | { imposition<exp-value-imp> } } } | action-strip-vlan | action-drop-pkt | divert-action | copy-action | action-decrement-ttl| forward-normal | goto-pmap <pmap-table-handle> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set attributeset
IEEE 802.1Q class of servicecos
IEEE 802.1Q class of servicecos1
IEEE 802.1Q class of servicecos2
802.1Q Class of Service valuecos-val
Action on Layer 2 destination MAC addresseth-dest-mac-addr
Action on Layer 2 source MAC addresseth-src-mac-addr
Layer 2 MAC Addresssrc-mac-addr
Layer 2 MAC Addressdest-mac-addr
Set the VLAN IDvlan
VLAN NUMBERvlan-number
Set the IPv4 TOSip-tos
IPv4 TOS Valueip-tos-value
IPV4 TOS Maskip-tos-mask
Output to a Specified Interfaceout-interface
Physical Interface Name and Number or Listiface-list
Perform the action STRIP-VLAN-IDaction-strip-vlan
Perform the action Drop the Packetaction-drop-pkt
Divert the packets to Controllerdivert-action
Copy the packets to Controllercopy-action
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3861
S Commandsset
Page 4006
Decrement TTL on the Packetaction-decrement-ttl
Forward the packets normallyforward-normal
Goto pmap/tablegoto-pmap
Pmap-table handlepmap-table-handle
DSCP in IP(v4) and IPv6 packetsdscp
DSCP in IP(v4) and IPv6 packetsdscp1
DSCP in IP(v4) and IPv6 packetsdscp2
(Optional) Set DSCP in tunnel encapsulationtunnel
DSCP valuedscp-val
dscp-enum
Precedence in IP(v4) and IPv6 packetsprecedence
Precedence in IP(v4) and IPv6 packetsprec1
Precedence in IP(v4) and IPv6 packetsprec2
(Optional) Set Precedence in tunnel encapsulationprec-tunnel
IP Precedence valueprec-val
prec-enum
Discard classdiscard-class
Discard classdis-class1
Discard classdis-class2
Discard class valuedis-class-val
Qos-groupqos-group
Qos-group valueqos-grp-val
Set MPLS labelmpls
Set MPLS experimental labelexperimental
Set MPLS topmost labeltopmost
Push the label and set new one on topimposition
MPLS valueexp-value
MPLS valueexp-value-imp
DSCP in IP(v4) and IPv6 packetsdscp3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3862
S Commandsset
Page 4007
mpls-exp-impositionmpls-exp-imposition
mpls-exp-topmostmpls-exp-topmost
DSCP in IP(v4) and IPv6 packetsdscp4
mpls-exp-topmostmpls-exp-topmost1
mpls-exp-topmostmpls-exp-topmost2
Command Mode
• /exec/configure/policy-map/type/plc/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3863
S Commandsset
Page 4008
set[no] set { { cos [ inner ] <cos-val> } | { dscp [ tunnel ] { <dscp-val> | <opt_set_dscp> } } | { precedence [tunnel1 ] { <prec-val> | <opt_set_prec> } } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set attributeset
IEEE 802.1Q class of servicecos
(Optional) Set inner 802.1Q class of service in QinQ environmentinner
802.1Q Class of Service valuecos-val
DSCP in IP(v4) and IPv6 packetsdscp
(Optional) Set DSCP in tunnel encapsulationtunnel
DSCP valuedscp-val
opt_set_dscp
Precedence in IP(v4) and IPv6 packetsprecedence
(Optional) Set DSCP in tunnel encapsulationtunnel1
IP Precedence valueprec-val
opt_set_prec
Command Mode
• /exec/configure/pmap/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3864
S Commandsset
Page 4009
setset <paramname> <paramval>
Syntax Description
Set the parameter valueset
Enter the name of the parameterparamname
Enter the parameter valueparamval
Command Mode
• /exec/configure/param-inst
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3865
S Commandsset
Page 4010
set[no] set { { dlb-disable } | { precedence [ prec-tunnel ] { <prec-val> | <prec-enum> } } | { dscp [ tunnel ] {<dscp-val> | <dscp-enum> } } | { cos <cos-val> } | { qos-group <qos-grp-val> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set attributeset
Disable Dynamic Load Balancingdlb-disable
Precedence in IP(v4) and IPv6 packetsprecedence
(Optional) Set Precedence in tunnel encapsulationprec-tunnel
IP Precedence valueprec-val
prec-enum
DSCP in IP(v4) and IPv6 packetsdscp
(Optional) Set DSCP in tunnel encapsulationtunnel
DSCP valuedscp-val
dscp-enum
IEEE 802.1Q Class of Servicecos
802.1Q Class of Service valuecos-val
Qos-groupqos-group
qos-grp-val
Command Mode
• /exec/configure/policy-map/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3866
S Commandsset
Page 4011
set[no] set { { discard-class <dis-class-val> } | { { { cos1 cos2 } | { dscp1 dscp2 } | { prec1 prec2 } | { dis-class1dis-class2 } | { dscp3 mpls-exp-imposition } | { mpls-exp-topmost dscp4 } | { mpls-exp-topmost1mpls-exp-topmost2 } } table <table-map-name> } | { mpls experimental { { topmost <exp-value> } | {imposition <exp-value-imp> } } } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set attributeset
IEEE 802.1Q class of servicecos1
IEEE 802.1Q class of servicecos2
DSCP in IP(v4) and IPv6 packetsdscp1
DSCP in IP(v4) and IPv6 packetsdscp2
Precedence in IP(v4) and IPv6 packetsprec1
Precedence in IP(v4) and IPv6 packetsprec2
Discard classdiscard-class
Discard classdis-class1
Discard classdis-class2
Discard class valuedis-class-val
Table defining mapping from input to outputtable
Table-map nametable-map-name
Set MPLS labelmpls
Set MPLS experimental labelexperimental
Set MPLS topmost labeltopmost
Push the label and set new one on topimposition
MPLS valueexp-value
MPLS valueexp-value-imp
DSCP in IP(v4) and IPv6 packetsdscp3
mpls-exp-impositionmpls-exp-imposition
mpls-exp-topmostmpls-exp-topmost
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3867
S Commandsset
Page 4012
DSCP in IP(v4) and IPv6 packetsdscp4
mpls-exp-topmostmpls-exp-topmost1
mpls-exp-topmostmpls-exp-topmost2
Command Mode
• /exec/configure/policy-map/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3868
S Commandsset
Page 4013
set[no] set { load-sharing per-packet }
Syntax Description
Set attributeset
Load sharing across ECMP by set out-of-order bitload-sharing
per MiM packetper-packet
(Optional) Negate a command or set its defaultsno
Command Mode
• /exec/configure/policy-map/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3869
S Commandsset
Page 4014
set as-path prepend last-as tag{ set as-path { prepend { last-as <lastas> | <as> + } | tag } } | { no set as-path { prepend [ last-as [ <lastas> ]| <as> + ] | tag } }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
Prepend string for a BGP AS-path attributeas-path
Prepend to the AS-Pathprepend
Prepend last AS to the as-pathlast-as
number of last-AS prependslastas
AS numberas
Set the tag as an AS-path attributetag
(Optional)as
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3870
S Commandsset as-path prepend last-as tag
Page 4015
set comm-list delete{ { set comm-list <name> delete } | { no set comm-list } }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
set BGP community list (for deletion)comm-list
Community list namename
Delete matching communitiesdelete
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3871
S Commandsset comm-list delete
Page 4016
set community none additive internet local-AS{ set community { none | { additive | internet | local-AS | no-advertise | no-export | <hex_num> | <number>| <community> } + } } | { no set community [ { none | { additive | internet | local-AS | no-advertise | no-export| <hex_num> | <number> | <community> } + } ] }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
Set BGP community attributecommunity
Add to existing communityadditive
Internet (well-known community)internet
Do not send outside local AS (well-known community)local-AS
Do not advertise to any peer (well-known community)no-advertise
Do not export to next AS (well-known community)no-export
No community attributenone
Community numbernumber
Community number in hexhex_num
Community number aa:nn formatcommunity
(Optional) internetadditive
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3872
S Commandsset community none additive internet local-AS
Page 4017
set cos[no] set cos <cos-val>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set attributeset
IEEE 802.1Q Class of Servicecos
802.1Q Class of Service valuecos-val
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3873
S Commandsset cos
Page 4018
set cos[no] set cos <cos-val>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set attributeset
IEEE 802.1Q class of servicecos
802.1Q Class of Service valuecos-val
Command Mode
• /exec/configure/policy-map/type/uf/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3874
S Commandsset cos
Page 4019
set dampening{ set dampening <halflife> <reuse> <supress> <duration> } | { no set dampening [ <halflife> <reuse> <supress><duration> ] }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
Set BGP route flap dampening parametersdampening
half-life time for the penaltyhalflife
penalty to start reusing a routereuse
penalty to start suppressing a routesupress
Maximum duration to suppress a stable routeduration
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3875
S Commandsset dampening
Page 4020
set distance{ set distance <external-dist> [ <internal-dist> [ <local-dist> ] ] } | { no set distance }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
Set the Administrative distance of routedistance
Administrative distance for IGP or EBGP routesexternal-dist
(Optional) Administrative distance for internal routesinternal-dist
(Optional) Administrative distance for local routeslocal-dist
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3876
S Commandsset distance
Page 4021
set drpvecset drpvec { parse_err <parse_err> | outer_ids_g0 <outer_ids_g0> | outer_ids_g1 <outer_ids_g1> | outer_ids_g2<outer_ids_g2> | outer_ids_g3 <outer_ids_g3> | outer_ids_g4 <outer_ids_g4> | outer_ids_g5 <outer_ids_g5>| outer_ids_g6 <outer_ids_g6> | outer_ids_g7 <outer_ids_g7> | outer_xlate_miss <outer_xlate_miss> |infra_encap_src_tep_miss <infra_encap_src_tep_miss> | infra_encap_type_mismatch<infra_encap_type_mismatch> | uc_tenant_mytep_route_miss <uc_tenant_mytep_route_miss> |uc_tenant_mytep_bridge_miss <uc_tenant_mytep_bridge_miss> | arp_nd_ucast_miss <arp_nd_ucast_miss>| mc_dvif_miss <mc_dvif_miss> | shard_override_vlan_xlate_miss <shard_override_vlan_xlate_miss> |fcf_check_failed <fcf_check_failed> | ttl_expired <ttl_expired> | security_group_deny <security_group_deny>| mc_iic <mc_iic> | mc_gipo_miss <mc_gipo_miss> | vif_miss <vif_miss> | missing_vntag <missing_vntag>| vlan_xlate_miss <vlan_xlate_miss> | ip_mtu_check_failure <ip_mtu_check_failure> | uc_rpf_failure<uc_rpf_failure> | mc_rpf_failure <mc_rpf_failure> | l3_binding_failure <l3_binding_failure> |nsh_not_allowed <nsh_not_allowed> | src_vlan_mbr <src_vlan_mbr> | nsh_src_sw_chk_failed<nsh_src_sw_chk_failed> | l2mp_iic_failed <l2mp_iic_failed> | l2mp_on_ce_bd <l2mp_on_ce_bd> |l2mp_encap_from_edge <l2mp_encap_from_edge> | l2mp_noencap_from_core <l2mp_noencap_from_core>| outer_ttl_expired <outer_ttl_expired> | incorrect_vntag_type <incorrect_vntag_type> | l2mp_ftag_comp_miss<l2mp_ftag_comp_miss> | ipv6_uc_link_local_cross_bd <ipv6_uc_link_local_cross_bd> |ipv6_mc_sa_local_da_global_svi <ipv6_mc_sa_local_da_global_svi> | ipv6_mc_sa_local_da_global_l3if<ipv6_mc_sa_local_da_global_l3if> | routing_disabled <routing_disabled> | fc_lookup_miss <fc_lookup_miss>| no_sgt_from_core <no_sgt_from_core> | ip_self_fwd_failure <ip_self_fwd_failure> | acl_drop <acl_drop>| smac_miss <smac_miss> | secure_mac_move <secure_mac_move> | non_secure_mac <non_secure_mac>| l2_binding_failure <l2_binding_failure> | inner_ids_g0 <inner_ids_g0> | inner_ids_g1 <inner_ids_g1> |inner_ids_g2 <inner_ids_g2> | inner_ids_g3 <inner_ids_g3> | inner_ids_g4 <inner_ids_g4> | inner_ids_g5<inner_ids_g5> | inner_ids_g6 <inner_ids_g6> | inner_ids_g7 <inner_ids_g7> | infra_encap_src_tep_drop<infra_encap_src_tep_drop> | split_horizon_check <split_horizon_check> | mc_fib_miss <mc_fib_miss> |mc_l2_miss <mc_l2_miss> | uc_df_check_failure <uc_df_check_failure> | uc_pc_cfg_table_drop<uc_pc_cfg_table_drop> | illegal_expl_null <illegal_expl_null> | mpls_lookup_miss <mpls_lookup_miss>| outer_cbl_check <outer_cbl_check> | null_shard_with_e_bit_set <null_shard_with_e_bit_set> | lb_drop<lb_drop> | nat_fragment <nat_fragment> | illegal_dce_pkt <illegal_dce_pkt> | dci_vnid_xlate_miss<dci_vnid_xlate_miss> | dci_sclass_xlate_miss <dci_sclass_xlate_miss> | dci_2nd_uc_transit<dci_2nd_uc_transit> } +
Syntax Description
Setup Triggerset
All drop vector fieldsdrpvec
Parse_Errparse_err
Parse_Errparse_err
Outer_Ids_G0outer_ids_g0
Outer_Ids_G0outer_ids_g0
Outer_Ids_G1outer_ids_g1
Outer_Ids_G1outer_ids_g1
Outer_Ids_G2outer_ids_g2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3877
S Commandsset drpvec
Page 4022
Outer_Ids_G2outer_ids_g2
Outer_Ids_G3outer_ids_g3
Outer_Ids_G3outer_ids_g3
Outer_Ids_G4outer_ids_g4
Outer_Ids_G4outer_ids_g4
Outer_Ids_G5outer_ids_g5
Outer_Ids_G5outer_ids_g5
Outer_Ids_G6outer_ids_g6
Outer_Ids_G6outer_ids_g6
Outer_Ids_G7outer_ids_g7
Outer_Ids_G7outer_ids_g7
Outer_Xlate_Missouter_xlate_miss
Outer_Xlate_Missouter_xlate_miss
Infra_Encap_Src_Tep_Missinfra_encap_src_tep_miss
Infra_Encap_Src_Tep_Missinfra_encap_src_tep_miss
Infra_Encap_Type_Mismatchinfra_encap_type_mismatch
Infra_Encap_Type_Mismatchinfra_encap_type_mismatch
Uc_Tenant_Mytep_Route_Missuc_tenant_mytep_route_miss
Uc_Tenant_Mytep_Route_Missuc_tenant_mytep_route_miss
Uc_Tenant_Mytep_Bridge_Missuc_tenant_mytep_bridge_miss
Uc_Tenant_Mytep_Bridge_Missuc_tenant_mytep_bridge_miss
Arp_Nd_Ucast_Missarp_nd_ucast_miss
Arp_Nd_Ucast_Missarp_nd_ucast_miss
Mc_Dvif_Missmc_dvif_miss
Mc_Dvif_Missmc_dvif_miss
Shard_Override_Vlan_Xlate_Missshard_override_vlan_xlate_miss
Shard_Override_Vlan_Xlate_Missshard_override_vlan_xlate_miss
Fcf_Check_Failedfcf_check_failed
Fcf_Check_Failedfcf_check_failed
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3878
S Commandsset drpvec
Page 4023
Ttl_Expiredttl_expired
Ttl_Expiredttl_expired
Security_Group_Denysecurity_group_deny
Security_Group_Denysecurity_group_deny
Mc_Iicmc_iic
Mc_Iicmc_iic
Mc_Gipo_Missmc_gipo_miss
Mc_Gipo_Missmc_gipo_miss
Vif_Missvif_miss
Vif_Missvif_miss
Missing_Vntagmissing_vntag
Missing_Vntagmissing_vntag
Vlan_Xlate_Missvlan_xlate_miss
Vlan_Xlate_Missvlan_xlate_miss
Ip_Mtu_Check_Failureip_mtu_check_failure
Ip_Mtu_Check_Failureip_mtu_check_failure
Uc_Rpf_Failureuc_rpf_failure
Uc_Rpf_Failureuc_rpf_failure
Mc_Rpf_Failuremc_rpf_failure
Mc_Rpf_Failuremc_rpf_failure
L3_Binding_Failurel3_binding_failure
L3_Binding_Failurel3_binding_failure
Nsh_Not_Allowednsh_not_allowed
Nsh_Not_Allowednsh_not_allowed
Src_Vlan_Mbrsrc_vlan_mbr
Src_Vlan_Mbrsrc_vlan_mbr
Nsh_Src_Sw_Chk_Failednsh_src_sw_chk_failed
Nsh_Src_Sw_Chk_Failednsh_src_sw_chk_failed
L2Mp_Iic_Failedl2mp_iic_failed
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3879
S Commandsset drpvec
Page 4024
L2Mp_Iic_Failedl2mp_iic_failed
L2Mp_On_Ce_Bdl2mp_on_ce_bd
L2Mp_On_Ce_Bdl2mp_on_ce_bd
L2Mp_Encap_From_Edgel2mp_encap_from_edge
L2Mp_Encap_From_Edgel2mp_encap_from_edge
L2Mp_Noencap_From_Corel2mp_noencap_from_core
L2Mp_Noencap_From_Corel2mp_noencap_from_core
Outer_Ttl_Expiredouter_ttl_expired
Outer_Ttl_Expiredouter_ttl_expired
Incorrect_Vntag_Typeincorrect_vntag_type
Incorrect_Vntag_Typeincorrect_vntag_type
L2Mp_Ftag_Comp_Missl2mp_ftag_comp_miss
L2Mp_Ftag_Comp_Missl2mp_ftag_comp_miss
Ipv6_Uc_Link_Local_Cross_Bdipv6_uc_link_local_cross_bd
Ipv6_Uc_Link_Local_Cross_Bdipv6_uc_link_local_cross_bd
Ipv6_Mc_Sa_Local_Da_Global_Sviipv6_mc_sa_local_da_global_svi
Ipv6_Mc_Sa_Local_Da_Global_Sviipv6_mc_sa_local_da_global_svi
Ipv6_Mc_Sa_Local_Da_Global_L3Ifipv6_mc_sa_local_da_global_l3if
Ipv6_Mc_Sa_Local_Da_Global_L3Ifipv6_mc_sa_local_da_global_l3if
Routing_Disabledrouting_disabled
Routing_Disabledrouting_disabled
Fc_Lookup_Missfc_lookup_miss
Fc_Lookup_Missfc_lookup_miss
No_Sgt_From_Coreno_sgt_from_core
No_Sgt_From_Coreno_sgt_from_core
Ip_Self_Fwd_Failureip_self_fwd_failure
Ip_Self_Fwd_Failureip_self_fwd_failure
Acl_Dropacl_drop
Acl_Dropacl_drop
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3880
S Commandsset drpvec
Page 4025
Smac_Misssmac_miss
Smac_Misssmac_miss
Secure_Mac_Movesecure_mac_move
Secure_Mac_Movesecure_mac_move
Non_Secure_Macnon_secure_mac
Non_Secure_Macnon_secure_mac
L2_Binding_Failurel2_binding_failure
L2_Binding_Failurel2_binding_failure
Inner_Ids_G0inner_ids_g0
Inner_Ids_G0inner_ids_g0
Inner_Ids_G1inner_ids_g1
Inner_Ids_G1inner_ids_g1
Inner_Ids_G2inner_ids_g2
Inner_Ids_G2inner_ids_g2
Inner_Ids_G3inner_ids_g3
Inner_Ids_G3inner_ids_g3
Inner_Ids_G4inner_ids_g4
Inner_Ids_G4inner_ids_g4
Inner_Ids_G5inner_ids_g5
Inner_Ids_G5inner_ids_g5
Inner_Ids_G6inner_ids_g6
Inner_Ids_G6inner_ids_g6
Inner_Ids_G7inner_ids_g7
Inner_Ids_G7inner_ids_g7
Infra_Encap_Src_Tep_Dropinfra_encap_src_tep_drop
Infra_Encap_Src_Tep_Dropinfra_encap_src_tep_drop
Split_Horizon_Checksplit_horizon_check
Split_Horizon_Checksplit_horizon_check
Mc_Fib_Missmc_fib_miss
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3881
S Commandsset drpvec
Page 4026
Mc_Fib_Missmc_fib_miss
Mc_L2_Missmc_l2_miss
Mc_L2_Missmc_l2_miss
Uc_Df_Check_Failureuc_df_check_failure
Uc_Df_Check_Failureuc_df_check_failure
Uc_Pc_Cfg_Table_Dropuc_pc_cfg_table_drop
Uc_Pc_Cfg_Table_Dropuc_pc_cfg_table_drop
Illegal_Expl_Nullillegal_expl_null
Illegal_Expl_Nullillegal_expl_null
Mpls_Lookup_Missmpls_lookup_miss
Mpls_Lookup_Missmpls_lookup_miss
Outer_Cbl_Checkouter_cbl_check
Outer_Cbl_Checkouter_cbl_check
Null_Shard_With_E_Bit_Setnull_shard_with_e_bit_set
Null_Shard_With_E_Bit_Setnull_shard_with_e_bit_set
Lb_Droplb_drop
Lb_Droplb_drop
Nat_Fragmentnat_fragment
Nat_Fragmentnat_fragment
Illegal_Dce_Pktillegal_dce_pkt
Illegal_Dce_Pktillegal_dce_pkt
Dci_Vnid_Xlate_Missdci_vnid_xlate_miss
Dci_Vnid_Xlate_Missdci_vnid_xlate_miss
Dci_Sclass_Xlate_Missdci_sclass_xlate_miss
Dci_Sclass_Xlate_Missdci_sclass_xlate_miss
Dci_2nd_Uc_Transitdci_2nd_uc_transit
Dci_2nd_Uc_Transitdci_2nd_uc_transit
Command Mode
• /exec/elamtah/outsel1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3882
S Commandsset drpvec
Page 4027
set drpvecset drpvec { parse_err <parse_err> | outer_ids_g0 <outer_ids_g0> | outer_ids_g1 <outer_ids_g1> | outer_ids_g2<outer_ids_g2> | outer_ids_g3 <outer_ids_g3> | outer_ids_g4 <outer_ids_g4> | outer_ids_g5 <outer_ids_g5>| outer_ids_g6 <outer_ids_g6> | outer_ids_g7 <outer_ids_g7> | outer_xlate_miss <outer_xlate_miss> |infra_encap_src_tep_miss <infra_encap_src_tep_miss> | infra_encap_type_mismatch<infra_encap_type_mismatch> | uc_tenant_mytep_route_miss <uc_tenant_mytep_route_miss> |uc_tenant_mytep_bridge_miss <uc_tenant_mytep_bridge_miss> | arp_nd_ucast_miss <arp_nd_ucast_miss>| mc_dvif_miss <mc_dvif_miss> | shard_override_vlan_xlate_miss <shard_override_vlan_xlate_miss> |fcf_check_failed <fcf_check_failed> | ttl_expired <ttl_expired> | security_group_deny <security_group_deny>| mc_iic <mc_iic> | mc_gipo_miss <mc_gipo_miss> | vif_miss <vif_miss> | missing_vntag <missing_vntag>| vlan_xlate_miss <vlan_xlate_miss> | ip_mtu_check_failure <ip_mtu_check_failure> | uc_rpf_failure<uc_rpf_failure> | mc_rpf_failure <mc_rpf_failure> | l3_binding_failure <l3_binding_failure> |nsh_not_allowed <nsh_not_allowed> | src_vlan_mbr <src_vlan_mbr> | nsh_src_sw_chk_failed<nsh_src_sw_chk_failed> | l2mp_iic_failed <l2mp_iic_failed> | l2mp_on_ce_bd <l2mp_on_ce_bd> |l2mp_encap_from_edge <l2mp_encap_from_edge> | l2mp_noencap_from_core <l2mp_noencap_from_core>| outer_ttl_expired <outer_ttl_expired> | incorrect_vntag_type <incorrect_vntag_type> | l2mp_ftag_comp_miss<l2mp_ftag_comp_miss> | ipv6_uc_link_local_cross_bd <ipv6_uc_link_local_cross_bd> |ipv6_mc_sa_local_da_global_svi <ipv6_mc_sa_local_da_global_svi> | ipv6_mc_sa_local_da_global_l3if<ipv6_mc_sa_local_da_global_l3if> | routing_disabled <routing_disabled> | fc_lookup_miss <fc_lookup_miss>| no_sgt_from_core <no_sgt_from_core> | ip_self_fwd_failure <ip_self_fwd_failure> | acl_drop <acl_drop>| smac_miss <smac_miss> | secure_mac_move <secure_mac_move> | non_secure_mac <non_secure_mac>| l2_binding_failure <l2_binding_failure> | inner_ids_g0 <inner_ids_g0> | inner_ids_g1 <inner_ids_g1> |inner_ids_g2 <inner_ids_g2> | inner_ids_g3 <inner_ids_g3> | inner_ids_g4 <inner_ids_g4> | inner_ids_g5<inner_ids_g5> | inner_ids_g6 <inner_ids_g6> | inner_ids_g7 <inner_ids_g7> | infra_encap_src_tep_drop<infra_encap_src_tep_drop> | split_horizon_check <split_horizon_check> | mc_fib_miss <mc_fib_miss> |mc_l2_miss <mc_l2_miss> | uc_df_check_failure <uc_df_check_failure> | uc_pc_cfg_table_drop<uc_pc_cfg_table_drop> | illegal_expl_null <illegal_expl_null> | mpls_lookup_miss <mpls_lookup_miss>| outer_cbl_check <outer_cbl_check> | null_shard_with_e_bit_set <null_shard_with_e_bit_set> | lb_drop<lb_drop> | nat_fragment <nat_fragment> | illegal_dce_pkt <illegal_dce_pkt> | dci_vnid_xlate_miss<dci_vnid_xlate_miss> | dci_sclass_xlate_miss <dci_sclass_xlate_miss> | dci_2nd_uc_transit<dci_2nd_uc_transit> } +
Syntax Description
Setup Triggerset
All drop vector fieldsdrpvec
Parse_Errparse_err
Parse_Errparse_err
Outer_Ids_G0outer_ids_g0
Outer_Ids_G0outer_ids_g0
Outer_Ids_G1outer_ids_g1
Outer_Ids_G1outer_ids_g1
Outer_Ids_G2outer_ids_g2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3883
S Commandsset drpvec
Page 4028
Outer_Ids_G2outer_ids_g2
Outer_Ids_G3outer_ids_g3
Outer_Ids_G3outer_ids_g3
Outer_Ids_G4outer_ids_g4
Outer_Ids_G4outer_ids_g4
Outer_Ids_G5outer_ids_g5
Outer_Ids_G5outer_ids_g5
Outer_Ids_G6outer_ids_g6
Outer_Ids_G6outer_ids_g6
Outer_Ids_G7outer_ids_g7
Outer_Ids_G7outer_ids_g7
Outer_Xlate_Missouter_xlate_miss
Outer_Xlate_Missouter_xlate_miss
Infra_Encap_Src_Tep_Missinfra_encap_src_tep_miss
Infra_Encap_Src_Tep_Missinfra_encap_src_tep_miss
Infra_Encap_Type_Mismatchinfra_encap_type_mismatch
Infra_Encap_Type_Mismatchinfra_encap_type_mismatch
Uc_Tenant_Mytep_Route_Missuc_tenant_mytep_route_miss
Uc_Tenant_Mytep_Route_Missuc_tenant_mytep_route_miss
Uc_Tenant_Mytep_Bridge_Missuc_tenant_mytep_bridge_miss
Uc_Tenant_Mytep_Bridge_Missuc_tenant_mytep_bridge_miss
Arp_Nd_Ucast_Missarp_nd_ucast_miss
Arp_Nd_Ucast_Missarp_nd_ucast_miss
Mc_Dvif_Missmc_dvif_miss
Mc_Dvif_Missmc_dvif_miss
Shard_Override_Vlan_Xlate_Missshard_override_vlan_xlate_miss
Shard_Override_Vlan_Xlate_Missshard_override_vlan_xlate_miss
Fcf_Check_Failedfcf_check_failed
Fcf_Check_Failedfcf_check_failed
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3884
S Commandsset drpvec
Page 4029
Ttl_Expiredttl_expired
Ttl_Expiredttl_expired
Security_Group_Denysecurity_group_deny
Security_Group_Denysecurity_group_deny
Mc_Iicmc_iic
Mc_Iicmc_iic
Mc_Gipo_Missmc_gipo_miss
Mc_Gipo_Missmc_gipo_miss
Vif_Missvif_miss
Vif_Missvif_miss
Missing_Vntagmissing_vntag
Missing_Vntagmissing_vntag
Vlan_Xlate_Missvlan_xlate_miss
Vlan_Xlate_Missvlan_xlate_miss
Ip_Mtu_Check_Failureip_mtu_check_failure
Ip_Mtu_Check_Failureip_mtu_check_failure
Uc_Rpf_Failureuc_rpf_failure
Uc_Rpf_Failureuc_rpf_failure
Mc_Rpf_Failuremc_rpf_failure
Mc_Rpf_Failuremc_rpf_failure
L3_Binding_Failurel3_binding_failure
L3_Binding_Failurel3_binding_failure
Nsh_Not_Allowednsh_not_allowed
Nsh_Not_Allowednsh_not_allowed
Src_Vlan_Mbrsrc_vlan_mbr
Src_Vlan_Mbrsrc_vlan_mbr
Nsh_Src_Sw_Chk_Failednsh_src_sw_chk_failed
Nsh_Src_Sw_Chk_Failednsh_src_sw_chk_failed
L2Mp_Iic_Failedl2mp_iic_failed
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3885
S Commandsset drpvec
Page 4030
L2Mp_Iic_Failedl2mp_iic_failed
L2Mp_On_Ce_Bdl2mp_on_ce_bd
L2Mp_On_Ce_Bdl2mp_on_ce_bd
L2Mp_Encap_From_Edgel2mp_encap_from_edge
L2Mp_Encap_From_Edgel2mp_encap_from_edge
L2Mp_Noencap_From_Corel2mp_noencap_from_core
L2Mp_Noencap_From_Corel2mp_noencap_from_core
Outer_Ttl_Expiredouter_ttl_expired
Outer_Ttl_Expiredouter_ttl_expired
Incorrect_Vntag_Typeincorrect_vntag_type
Incorrect_Vntag_Typeincorrect_vntag_type
L2Mp_Ftag_Comp_Missl2mp_ftag_comp_miss
L2Mp_Ftag_Comp_Missl2mp_ftag_comp_miss
Ipv6_Uc_Link_Local_Cross_Bdipv6_uc_link_local_cross_bd
Ipv6_Uc_Link_Local_Cross_Bdipv6_uc_link_local_cross_bd
Ipv6_Mc_Sa_Local_Da_Global_Sviipv6_mc_sa_local_da_global_svi
Ipv6_Mc_Sa_Local_Da_Global_Sviipv6_mc_sa_local_da_global_svi
Ipv6_Mc_Sa_Local_Da_Global_L3Ifipv6_mc_sa_local_da_global_l3if
Ipv6_Mc_Sa_Local_Da_Global_L3Ifipv6_mc_sa_local_da_global_l3if
Routing_Disabledrouting_disabled
Routing_Disabledrouting_disabled
Fc_Lookup_Missfc_lookup_miss
Fc_Lookup_Missfc_lookup_miss
No_Sgt_From_Coreno_sgt_from_core
No_Sgt_From_Coreno_sgt_from_core
Ip_Self_Fwd_Failureip_self_fwd_failure
Ip_Self_Fwd_Failureip_self_fwd_failure
Acl_Dropacl_drop
Acl_Dropacl_drop
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3886
S Commandsset drpvec
Page 4031
Smac_Misssmac_miss
Smac_Misssmac_miss
Secure_Mac_Movesecure_mac_move
Secure_Mac_Movesecure_mac_move
Non_Secure_Macnon_secure_mac
Non_Secure_Macnon_secure_mac
L2_Binding_Failurel2_binding_failure
L2_Binding_Failurel2_binding_failure
Inner_Ids_G0inner_ids_g0
Inner_Ids_G0inner_ids_g0
Inner_Ids_G1inner_ids_g1
Inner_Ids_G1inner_ids_g1
Inner_Ids_G2inner_ids_g2
Inner_Ids_G2inner_ids_g2
Inner_Ids_G3inner_ids_g3
Inner_Ids_G3inner_ids_g3
Inner_Ids_G4inner_ids_g4
Inner_Ids_G4inner_ids_g4
Inner_Ids_G5inner_ids_g5
Inner_Ids_G5inner_ids_g5
Inner_Ids_G6inner_ids_g6
Inner_Ids_G6inner_ids_g6
Inner_Ids_G7inner_ids_g7
Inner_Ids_G7inner_ids_g7
Infra_Encap_Src_Tep_Dropinfra_encap_src_tep_drop
Infra_Encap_Src_Tep_Dropinfra_encap_src_tep_drop
Split_Horizon_Checksplit_horizon_check
Split_Horizon_Checksplit_horizon_check
Mc_Fib_Missmc_fib_miss
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3887
S Commandsset drpvec
Page 4032
Mc_Fib_Missmc_fib_miss
Mc_L2_Missmc_l2_miss
Mc_L2_Missmc_l2_miss
Uc_Df_Check_Failureuc_df_check_failure
Uc_Df_Check_Failureuc_df_check_failure
Uc_Pc_Cfg_Table_Dropuc_pc_cfg_table_drop
Uc_Pc_Cfg_Table_Dropuc_pc_cfg_table_drop
Illegal_Expl_Nullillegal_expl_null
Illegal_Expl_Nullillegal_expl_null
Mpls_Lookup_Missmpls_lookup_miss
Mpls_Lookup_Missmpls_lookup_miss
Outer_Cbl_Checkouter_cbl_check
Outer_Cbl_Checkouter_cbl_check
Null_Shard_With_E_Bit_Setnull_shard_with_e_bit_set
Null_Shard_With_E_Bit_Setnull_shard_with_e_bit_set
Lb_Droplb_drop
Lb_Droplb_drop
Nat_Fragmentnat_fragment
Nat_Fragmentnat_fragment
Illegal_Dce_Pktillegal_dce_pkt
Illegal_Dce_Pktillegal_dce_pkt
Dci_Vnid_Xlate_Missdci_vnid_xlate_miss
Dci_Vnid_Xlate_Missdci_vnid_xlate_miss
Dci_Sclass_Xlate_Missdci_sclass_xlate_miss
Dci_Sclass_Xlate_Missdci_sclass_xlate_miss
Dci_2nd_Uc_Transitdci_2nd_uc_transit
Dci_2nd_Uc_Transitdci_2nd_uc_transit
Command Mode
• /exec/elamtah/outsel2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3888
S Commandsset drpvec
Page 4033
set extcomm-list delete{ { set extcomm-list <name> delete } | { no set extcomm-list [ <name> delete ] } }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
set BGP extcommunity list (for deletion)extcomm-list
Extended Community list namename
Delete matching extcommunitiesdelete
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3889
S Commandsset extcomm-list delete
Page 4034
set extcommunity 4byteas-generic transitive additive{ set extcommunity 4byteas-generic { { transitive <ext-comm-gen-trans> | non-transitive<ext-comm-gen-nontrans> } + [ additive ] | additive | none } } | { no set extcommunity 4byteas-generic [ {transitive <ext-comm-gen-trans> | non-transitive <ext-comm-gen-nontrans> } + [ additive ] | additive | none] }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
Set BGP extcommunity attributeextcommunity
Generic extended community4byteas-generic
(Optional) Add to existing generic extcommunityadditive
No extcommunity generic attributenone
Transitive extended communitytransitive
Non-Transitive extended communitynon-transitive
Extcommunity number aa4:nn formatext-comm-gen-trans
Extcommunity number aa4:nn formatext-comm-gen-nontrans
(Optional) <ext-comm-gen-nontrans>ext-comm-gen-trans
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3890
S Commandsset extcommunity 4byteas-generic transitive additive
Page 4035
set extcommunity color{ set extcommunity color <color-value> } | { no set extcommunity color [ <color-value> ] }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
Set BGP extcommunity attributeextcommunity
Color Extended Communitycolor
Color Community valuecolor-value
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3891
S Commandsset extcommunity color
Page 4036
set extcommunity cost{ set extcommunity cost { [ igp | pre-bestpath ] <comm-id> <cost-value> } + } | { no set extcommunity cost[ [ igp | pre-bestpath ] <comm-id> <cost-value> ] + }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
Set BGP extcommunity attributeextcommunity
Costcost
(Optional) Compare following IGP cost comparisonigp
(Optional) Compare before all other steps in bestpath calculationpre-bestpath
Community IDcomm-id
Cost Community valuecost-value
(Optional) <cost-value>comm-id
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3892
S Commandsset extcommunity cost
Page 4037
set extcommunity rt additive{ set extcommunity rt { { <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } + [ additive ] | additive } } | {no set extcommunity rt [ { <ext-comm-rt-aa2nn4> | <ext-comm-rt-aa4nn2> } + [ additive ] | additive ] }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
Set BGP extcommunity attributeextcommunity
Route-Targetrt
(Optional) Add to existing rt extcommunityadditive
Extcommunity numberext-comm-rt-aa2nn4
Extcommunity numberext-comm-rt-aa4nn2
(Optional) <ext-comm-rt-aa4nn2>ext-comm-rt-aa2nn4
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3893
S Commandsset extcommunity rt additive
Page 4038
set forwarding-address[no] set forwarding-address
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Set the forwarding addressforwarding-address
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3894
S Commandsset forwarding-address
Page 4039
set iethset ieth { sof <sof_val> | hdr_type <hdr_type> | ext_hd <ext_hd> | opcode <opcode> | src_idx <src_idx> |dst_idx <dst_idx> | src_chip <src_chip> | src_port <src_port> | dst_chip <dst_chip> | dst_port <dst_port> |outer_bd <outer_bd> | bd <bd> | traceroute <traceroute> | dont_lrn <dont_lrn> | span <span> | alt_if_prof<alt_if_prof> | ttl_bypass <ttl_bypass> | src_is_tunl <src_is_tunl> | dst_is_tunl <dst_is_tunl> | l2_tunl <l2_tunl>| sup_tx <sup_tx> | sup_code <sup_code> | cos_de <cos_de> | tclass <tclass> | src_is_peer <src_is_peer> |pkt_hash <pkt_hash> } +
Syntax Description
Setup Triggerset
All iETH Hdr Fieldsieth
Start of Framesof
Start of Framesof_val
Header Typehdr_type
Header Typehdr_type
Ext hdext_hd
Ext hdext_hd
Opcodeopcode
Opcodeopcode
Source Indexsrc_idx
Source Indexsrc_idx
Destination Indexdst_idx
Destination Indexdst_idx
Source Chipsrc_chip
Source Chipsrc_chip
Source Portsrc_port
Source Portsrc_port
Destination Chipdst_chip
Destination Chipdst_chip
Destination Portdst_port
Destination Portdst_port
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3895
S Commandsset ieth
Page 4040
Outer BDouter_bd
Outer BDouter_bd
BDbd
BDbd
Trace Routetraceroute
Trace Routetraceroute
Don't Learndont_lrn
Don't Learndont_lrn
Spanspan
Spanspan
Alternate IF Profilealt_if_prof
Alternate IF Profilealt_if_prof
TTL Bypassttl_bypass
TTL Bypassttl_bypass
Source is Tunnelsrc_is_tunl
Source is Tunnelsrc_is_tunl
Destination is Tunneldst_is_tunl
Destination is Tunneldst_is_tunl
L2 Tunnell2_tunl
L2 Tunnell2_tunl
Sup Txsup_tx
Sup Txsup_tx
Sup Codesup_code
Sup Codesup_code
Cos Decos_de
Cos Decos_de
Tclasstclass
Tclasstclass
Source is Peersrc_is_peer
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3896
S Commandsset ieth
Page 4041
Source is Peersrc_is_peer
Packet Hashpkt_hash
Packet Hashpkt_hash
Command Mode
• /exec/elamtah/insel8
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3897
S Commandsset ieth
Page 4042
set iethset ieth { sof <sof_val> | hdr_type <hdr_type> | ext_hd <ext_hd> | opcode <opcode> | src_idx <src_idx> |dst_idx <dst_idx> | src_chip <src_chip> | src_port <src_port> | dst_chip <dst_chip> | dst_port <dst_port> |outer_bd <outer_bd> | bd <bd> | traceroute <traceroute> | dont_lrn <dont_lrn> | span <span> | alt_if_prof<alt_if_prof> | ttl_bypass <ttl_bypass> | src_is_tunl <src_is_tunl> | dst_is_tunl <dst_is_tunl> | l2_tunl <l2_tunl>| sup_tx <sup_tx> | sup_code <sup_code> | cos_de <cos_de> | tclass <tclass> | src_is_peer <src_is_peer> |pkt_hash <pkt_hash> } +
Syntax Description
Setup Triggerset
All iETH Hdr Fieldsieth
Start of Framesof
Start of Framesof_val
Header Typehdr_type
Header Typehdr_type
Ext hdext_hd
Ext hdext_hd
Opcodeopcode
Opcodeopcode
Source Indexsrc_idx
Source Indexsrc_idx
Destination Indexdst_idx
Destination Indexdst_idx
Source Chipsrc_chip
Source Chipsrc_chip
Source Portsrc_port
Source Portsrc_port
Destination Chipdst_chip
Destination Chipdst_chip
Destination Portdst_port
Destination Portdst_port
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3898
S Commandsset ieth
Page 4043
Outer BDouter_bd
Outer BDouter_bd
BDbd
BDbd
Trace Routetraceroute
Trace Routetraceroute
Don't Learndont_lrn
Don't Learndont_lrn
Spanspan
Spanspan
Alternate IF Profilealt_if_prof
Alternate IF Profilealt_if_prof
TTL Bypassttl_bypass
TTL Bypassttl_bypass
Source is Tunnelsrc_is_tunl
Source is Tunnelsrc_is_tunl
Destination is Tunneldst_is_tunl
Destination is Tunneldst_is_tunl
L2 Tunnell2_tunl
L2 Tunnell2_tunl
Sup Txsup_tx
Sup Txsup_tx
Sup Codesup_code
Sup Codesup_code
Cos Decos_de
Cos Decos_de
Tclasstclass
Tclasstclass
Source is Peersrc_is_peer
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3899
S Commandsset ieth
Page 4044
Source is Peersrc_is_peer
Packet Hashpkt_hash
Packet Hashpkt_hash
Command Mode
• /exec/elamtah/insel10
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3900
S Commandsset ieth
Page 4045
set inner arpset inner arp { target-ip-addr <tipaddr> | target-mac-addr <tmac> | source-ip-addr <sipaddr> | source-mac-addr<smac> | opcode <opcode_val> | prot-addr-len <prot_addr_len> | hw-addr-len <hw_addr_len> | protocol-type<prot_type> | hardware-type <hw_type> | ether-type <etype> | payload-len <pyld_len> } +
Syntax Description
Setup Triggerset
Mask and Match By Inner Packet Fieldsinner
ARP Fieldsarp
ARP Target IP Addresstarget-ip-addr
ARP Target IP Addresstipaddr
ARP Target MAC Addresstarget-mac-addr
ARP Target MAC Addresstmac
ARP Source IP Addresssource-ip-addr
ARP Source IP Addresssipaddr
ARP Source MAC Addresssource-mac-addr
ARP Source MAC Addresssmac
ARP Opcodeopcode
ARP Opcodeopcode_val
ARP Protocol Address Lengthprot-addr-len
ARP Protocol Address Lengthprot_addr_len
ARP Hardware Address Lengthhw-addr-len
ARP Hardware Address Lengthhw_addr_len
ARP Protocol Typeprotocol-type
ARP Protocol Typeprot_type
ARP Hardware Typehardware-type
ARP Hardware Typehw_type
ARP Ether Type - 0x0806 -> ARP 0x8035 -> RARPether-type
ARP Ether Type - 0x0806 -> ARP 0x8035 -> RARPetype
ARP Payload Lengthpayload-len
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3901
S Commandsset inner arp
Page 4046
ARP Payload Lengthpyld_len
Command Mode
• /exec/elamtah/insel7
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3902
S Commandsset inner arp
Page 4047
set inner ipv4set inner ipv4 { pyld-len <pyld_len> | version <ver> | header-len <hlen> | dscp <dscp_val> | ecn <ecn_val>| packet-len <pkt_len> | more-frags <mf> | fragment-off <fragoff> | ttl <ttl_val> | next-protocol <nproto> |checksum <csum> | src_ip <sip> | dst_ip <dip> } +
Syntax Description
Setup Triggerset
Mask and Match By Inner Packet Fieldsinner
IPv4 Fieldsipv4
Payload Lengthpyld-len
Payload Lengthpyld_len
Versionversion
Versionver
Header Lengthheader-len
Header Lengthhlen
Diff. Serv. Code Pointdscp
Diff. Serv. Code Pointdscp_val
Explicit Congestion Ntfnecn
Explicit Congestion Ntfnecn_val
Packet Total Lengthpacket-len
Packet Total Lengthpkt_len
More Fragments Availablemore-frags
More Fragments Availablemf
Fragments Offsetfragment-off
Fragments Offsetfragoff
Time to Livettl
Time to Livettl_val
Next Protocolnext-protocol
Next Protocolnproto
Checksumchecksum
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3903
S Commandsset inner ipv4
Page 4048
Checksumcsum
Source IP Addresssrc_ip
Source IP Addresssip
Destination IP Addressdst_ip
Destination IP Addressdip
Command Mode
• /exec/elamtah/insel7
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3904
S Commandsset inner ipv4
Page 4049
set inner ipv4set { inner | outer } ipv4 [ { l3-type <l3_type> | pyld-len <pyld_len> | v6-vld <v6_vld> | version <ver> |header-len <hlen> | dscp <dscp_val> | ecn <ecn_val> | packet-len <pkt_len> | more-frags <mf> | fragment-off<fragoff> | ttl <ttl_val> | next-protocol <nproto> | checksum <csum> | src_ip <sip> | dst_ip <dip> } ] +
Syntax Description
Setup Triggerset
Mask and Match By Inner Packet Fieldsinner
Mask and Match By Outer Packet Fieldsouter
IPv4 Fieldsipv4
(Optional) L3 Packet Typel3-type
(Optional) L3 Packet Typel3_type
(Optional) Payload Lengthpyld-len
(Optional) Payload Lengthpyld_len
(Optional) IPv6 Valid Informationv6-vld
(Optional) IPv6 Valid Informationv6_vld
(Optional) Versionversion
(Optional) Versionver
(Optional) Header Lengthheader-len
(Optional) Header Lengthhlen
(Optional) Diff. Serv. Code Pointdscp
(Optional) Diff. Serv. Code Pointdscp_val
(Optional) Explicit Congestion Ntfnecn
(Optional) Explicit Congestion Ntfnecn_val
(Optional) Packet Total Lengthpacket-len
(Optional) Packet Total Lengthpkt_len
(Optional) More Fragments Availablemore-frags
(Optional) More Fragments Availablemf
(Optional) Fragments Offsetfragment-off
(Optional) Fragments Offsetfragoff
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3905
S Commandsset inner ipv4
Page 4050
(Optional) Time to Livettl
(Optional) Time to Livettl_val
(Optional) Next(L4) Protocolnext-protocol
(Optional) Next(L4) Protocolnproto
(Optional) Checksumchecksum
(Optional) Checksumcsum
(Optional) Source IP Addresssrc_ip
(Optional) Source IP Addresssip
(Optional) Destination IP Addressdst_ip
(Optional) Destination IP Addressdip
Command Mode
• /exec/elamns/sel6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3906
S Commandsset inner ipv4
Page 4051
set inner ipv4set inner ipv4 [ { l3-type <l3_type> | pyld-len <pyld_len> | v6-vld <v6_vld> | version <ver> | header-len<hlen> | dscp <dscp_val> | ecn <ecn_val> | packet-len <pkt_len> | more-frags <mf> | fragment-off <fragoff>| ttl <ttl_val> | next-protocol <nproto> | checksum <csum> | src_ip <sip> | dst_ip <dip> } ] +
Syntax Description
Setup Triggerset
Mask and Match By Inner Packet Fieldsinner
IPv4 Fieldsipv4
(Optional) L3 Packet Typel3-type
(Optional) L3 Packet Typel3_type
(Optional) Payload Lengthpyld-len
(Optional) Payload Lengthpyld_len
(Optional) IPv6 Valid Informationv6-vld
(Optional) IPv6 Valid Informationv6_vld
(Optional) Versionversion
(Optional) Versionver
(Optional) Header Lengthheader-len
(Optional) Header Lengthhlen
(Optional) Diff. Serv. Code Pointdscp
(Optional) Diff. Serv. Code Pointdscp_val
(Optional) Explicit Congestion Ntfnecn
(Optional) Explicit Congestion Ntfnecn_val
(Optional) Packet Total Lengthpacket-len
(Optional) Packet Total Lengthpkt_len
(Optional) More Fragments Availablemore-frags
(Optional) More Fragments Availablemf
(Optional) Fragments Offsetfragment-off
(Optional) Fragments Offsetfragoff
(Optional) Time to Livettl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3907
S Commandsset inner ipv4
Page 4052
(Optional) Time to Livettl_val
(Optional) Next(L4) Protocolnext-protocol
(Optional) Next(L4) Protocolnproto
(Optional) Checksumchecksum
(Optional) Checksumcsum
(Optional) Source IP Addresssrc_ip
(Optional) Source IP Addresssip
(Optional) Destination IP Addressdst_ip
(Optional) Destination IP Addressdip
Command Mode
• /exec/elamns/sel4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3908
S Commandsset inner ipv4
Page 4053
set inner ipv6 src_ipset inner ipv6 { src_ip <sip> | dst_ip <dip> } +
Syntax Description
Setup Triggerset
Mask and Match By Inner Packet Fieldsinner
IPv6 Fieldsipv6
Source IP Addresssrc_ip
Destination IP Addressdst_ip
Command Mode
• /exec/elamtah/insel7
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3909
S Commandsset inner ipv6 src_ip
Page 4054
set inner l2set inner l2 [ { snap_vld <snap_vld> | cntag_vld <cntag_vld> | qtag_vld <qtag_vld> | vlan <vlan_id> | cos<cos_val> | cfi <cfi_vld> | vntag_vld <vntag_vld> | vntag_svif <vntag_svif> | vntag_dvif <vntag_dvif> |vntag_looped <vntag_loop> | vntag_pointer <vntag_p> | src_mac <smac> | dst_mac <dmac> } ] +
Syntax Description
Setup Triggerset
Mask and Match By Inner Packet Fieldsinner
All Layer 2 Fieldsl2
(Optional) SNAP Header Information Validsnap_vld
(Optional) SNAP Header Information Validsnap_vld
(Optional) CNTag Information Validcntag_vld
(Optional) CNTag Information Validcntag_vld
(Optional) VLAN Tag Information Validqtag_vld
(Optional) VLAN Tag Information Validqtag_vld
(Optional) VLAN Id (Present only in case of FEX)vlan
(Optional) VLAN Idvlan_id
(Optional) Class of Servicecos
(Optional) Class of Service Typecos_val
(Optional) CFI Settingcfi
(Optional) CFI Setting Validcfi_vld
(Optional) VNTAG Information Validvntag_vld
(Optional) VNTAG Information Validvntag_vld
(Optional) VNTAG Source vifvntag_svif
(Optional) VNTAG Source vifvntag_svif
(Optional) VNTAG Destination vifvntag_dvif
(Optional) VNTAG Destination vifvntag_dvif
(Optional) VNTAG Header Looped Validvntag_looped
(Optional) VNTAG Header Looped Validvntag_loop
(Optional) VNTAG Header Pointer Validvntag_pointer
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3910
S Commandsset inner l2
Page 4055
(Optional) VNTAG Header Pointer Validvntag_p
(Optional) Source MAC Addresssrc_mac
(Optional) Source MAC Address Valuesmac
(Optional) Destination MAC Addressdst_mac
(Optional) Destination MAC Address Valuedmac
Command Mode
• /exec/elamns/sel4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3911
S Commandsset inner l2
Page 4056
set inner l2set inner l2 { snap_vld <snap_vld> | cntag_vld <cntag_vld> | qtag_vld <qtag_vld> | vlan <vlan_id> | cos<cos_val> | cfi <cfi_vld> | vntag_vld <vntag_vld> | vntag_svif <vntag_svif> | vntag_dvif <vntag_dvif> |vntag_looped <vntag_loop> | vntag_pointer <vntag_p> | src_mac <smac> | dst_mac <dmac> } +
Syntax Description
Setup Triggerset
Mask and Match By Inner Packet Fieldsinner
All Layer 2 Fieldsl2
SNAP Header Information Validsnap_vld
SNAP Header Information Validsnap_vld
CNTag Information Validcntag_vld
CNTag Information Validcntag_vld
VLAN Tag Information Validqtag_vld
VLAN Tag Information Validqtag_vld
VLAN Id (Present only in case of FEX)vlan
VLAN Idvlan_id
Class of Servicecos
Class of Service Typecos_val
CFI Settingcfi
CFI Setting Validcfi_vld
VNTAG Information Validvntag_vld
VNTAG Information Validvntag_vld
VNTAG Source vifvntag_svif
VNTAG Source vifvntag_svif
VNTAG Destination vifvntag_dvif
VNTAG Destination vifvntag_dvif
VNTAG Header Looped Validvntag_looped
VNTAG Header Looped Validvntag_loop
VNTAG Header Pointer Validvntag_pointer
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3912
S Commandsset inner l2
Page 4057
VNTAG Header Pointer Validvntag_p
Source MAC Addresssrc_mac
Source MAC Address Valuesmac
Destination MAC Addressdst_mac
Destination MAC Address Valuedmac
Command Mode
• /exec/elamtah/insel7
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3913
S Commandsset inner l2
Page 4058
set inner l2set { inner | outer } l2 [ { snap_vld <snap_vld> | cntag_vld <cntag_vld> | qtag_vld <qtag_vld> | vlan <vlan_id>| cos <cos_val> | cfi <cfi_vld> | vntag_vld <vntag_vld> | vntag_svif <vntag_svif> | vntag_dvif <vntag_dvif>| vntag_looped <vntag_loop> | vntag_pointer <vntag_p> | src_mac <smac> | dst_mac <dmac> } ] +
Syntax Description
Setup Triggerset
Mask and Match By Inner Packet Fieldsinner
Mask and Match By Outer Packet Fieldsouter
All Layer 2 Fieldsl2
(Optional) SNAP Header Information Validsnap_vld
(Optional) SNAP Header Information Validsnap_vld
(Optional) CNTag Information Validcntag_vld
(Optional) CNTag Information Validcntag_vld
(Optional) VLAN Tag Information Validqtag_vld
(Optional) VLAN Tag Information Validqtag_vld
(Optional) VLAN Id (Present only in case of FEX)vlan
(Optional) VLAN Idvlan_id
(Optional) Class of Servicecos
(Optional) Class of Service Typecos_val
(Optional) CFI Settingcfi
(Optional) CFI Setting Validcfi_vld
(Optional) VNTAG Information Validvntag_vld
(Optional) VNTAG Information Validvntag_vld
(Optional) VNTAG Source vifvntag_svif
(Optional) VNTAG Source vifvntag_svif
(Optional) VNTAG Destination vifvntag_dvif
(Optional) VNTAG Destination vifvntag_dvif
(Optional) VNTAG Header Looped Validvntag_looped
(Optional) VNTAG Header Looped Validvntag_loop
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3914
S Commandsset inner l2
Page 4059
(Optional) VNTAG Header Pointer Validvntag_pointer
(Optional) VNTAG Header Pointer Validvntag_p
(Optional) Source MAC Addresssrc_mac
(Optional) Source MAC Address Valuesmac
(Optional) Destination MAC Addressdst_mac
(Optional) Destination MAC Address Valuedmac
Command Mode
• /exec/elamns/sel5
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3915
S Commandsset inner l2
Page 4060
set inner l2 hg2set { inner | outer } l2 hg2 [ { hg2_vid <hg2_vlan> | hg2_ppd_type <hg2_ppd_type> | hg2_mirror <hg2_mirror>| hg2_opcode <hg2_opcode> | hg2_dstpid <hg2_dpid> | hg2_dstmod <hg2_dmod> | hg2_srcpid <hg2_spid>| hg2_srcmod <hg2_smod> | hg2_l3vld <hg2_l3_vld> | hg2_tc <hg2_tc> | hg2_dp <hg2_dp> | hg2_mcast<hg2_mcast_vld> | hg2-vld <hg2_vld> | hg2-cos <hg2_cos> } ] +
Syntax Description
Setup Triggerset
Mask and Match By Inner Packet Fieldsinner
Mask and Match By Outer Packet Fieldsouter
All Layer 2 Fieldsl2
High Gig2 Fieldshg2
(Optional) High Gig2 VLAN Taghg2_vid
(Optional) High Gig2 VLAN Tag Informationhg2_vlan
(Optional) High Gig2 Packet Processing Descriptorhg2_ppd_type
(Optional) High Gig2 Packet Processing Descriptorhg2_ppd_type
(Optional) High Gig2 Packet Mirror Informationhg2_mirror
(Optional) High Gig2 Packet Mirror Informationhg2_mirror
(Optional) High Gig2 Packet Typehg2_opcode
(Optional) High Gig2 Packet Typehg2_opcode
(Optional) High Gig2 Destination Port IDhg2_dstpid
(Optional) High Gig2 Destination Port IDhg2_dpid
(Optional) High Gig2 Destination Module IDhg2_dstmod
(Optional) High Gig2 Destination Module IDhg2_dmod
(Optional) High Gig2 Source Port IDhg2_srcpid
(Optional) High Gig2 Source Port IDhg2_spid
(Optional) High Gig2 Souce Module IDhg2_srcmod
(Optional) High Gig2 Souce Module IDhg2_smod
(Optional) High Gig2 Packet L3 Switchedhg2_l3vld
(Optional) High Gig2 Packet L3 Switchedhg2_l3_vld
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3916
S Commandsset inner l2 hg2
Page 4061
(Optional) High Gig2 Packet Traffic Classhg2_tc
(Optional) High Gig2 Packet Traffic Classhg2_tc
(Optional) High Gig2 Drop Precedencehg2_dp
(Optional) High Gig2 Drop Precedencehg2_dp
(Optional) High Gig2 MultiCast Forwarding Informationhg2_mcast
(Optional) High Gig2 Multicast Forwarding Informationhg2_mcast_vld
(Optional) High Gig2 Valid Informationhg2-vld
(Optional) High Gig2 Valid Informationhg2_vld
(Optional) High Gig2 CoS Informationhg2-cos
(Optional) High Gig2 CoS Informationhg2_cos
Command Mode
• /exec/elamns/sel5
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3917
S Commandsset inner l2 hg2
Page 4062
set inner l2 hg2set inner l2 hg2 [ { hg2_vid <hg2_vlan> | hg2_ppd_type <hg2_ppd_type> | hg2_mirror <hg2_mirror> |hg2_opcode <hg2_opcode> | hg2_dstpid <hg2_dpid> | hg2_dstmod <hg2_dmod> | hg2_srcpid <hg2_spid>| hg2_srcmod <hg2_smod> | hg2_l3vld <hg2_l3_vld> | hg2_tc <hg2_tc> | hg2_dp <hg2_dp> | hg2_mcast<hg2_mcast_vld> | hg2-vld <hg2_vld> | hg2-cos <hg2_cos> } ] +
Syntax Description
Setup Triggerset
Mask and Match By Inner Packet Fieldsinner
All Layer 2 Fieldsl2
High Gig2 Fieldshg2
(Optional) High Gig2 VLAN Taghg2_vid
(Optional) High Gig2 VLAN Tag Informationhg2_vlan
(Optional) High Gig2 Packet Processing Descriptorhg2_ppd_type
(Optional) High Gig2 Packet Processing Descriptorhg2_ppd_type
(Optional) High Gig2 Packet Mirror Informationhg2_mirror
(Optional) High Gig2 Packet Mirror Informationhg2_mirror
(Optional) High Gig2 Packet Typehg2_opcode
(Optional) High Gig2 Packet Typehg2_opcode
(Optional) High Gig2 Destination Port IDhg2_dstpid
(Optional) High Gig2 Destination Port IDhg2_dpid
(Optional) High Gig2 Destination Module IDhg2_dstmod
(Optional) High Gig2 Destination Module IDhg2_dmod
(Optional) High Gig2 Source Port IDhg2_srcpid
(Optional) High Gig2 Source Port IDhg2_spid
(Optional) High Gig2 Souce Module IDhg2_srcmod
(Optional) High Gig2 Souce Module IDhg2_smod
(Optional) High Gig2 Packet L3 Switchedhg2_l3vld
(Optional) High Gig2 Packet L3 Switchedhg2_l3_vld
(Optional) High Gig2 Packet Traffic Classhg2_tc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3918
S Commandsset inner l2 hg2
Page 4063
(Optional) High Gig2 Packet Traffic Classhg2_tc
(Optional) High Gig2 Drop Precedencehg2_dp
(Optional) High Gig2 Drop Precedencehg2_dp
(Optional) High Gig2 MultiCast Forwarding Informationhg2_mcast
(Optional) High Gig2 Multicast Forwarding Informationhg2_mcast_vld
(Optional) High Gig2 Valid Informationhg2-vld
(Optional) High Gig2 Valid Informationhg2_vld
(Optional) High Gig2 CoS Informationhg2-cos
(Optional) High Gig2 CoS Informationhg2_cos
Command Mode
• /exec/elamns/sel4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3919
S Commandsset inner l2 hg2
Page 4064
set inner l4set { inner | outer } l4 [ { src-port <sport> | dst-port <dport> | packet-len <pkt_len> | checksum <csum> | flags<flag_val> } ] +
Syntax Description
Setup Triggerset
Mask and Match By Inner Packet Fieldsinner
Mask and Match By Outer Packet Fieldsouter
L4 Fieldsl4
(Optional) Source Port Informationsrc-port
(Optional) Source Portsport
(Optional) Destination Port Informationdst-port
(Optional) Destination Portdport
(Optional) Packet Lengthpacket-len
(Optional) Packet Lengthpkt_len
(Optional) Checksumchecksum
(Optional) Checksumcsum
(Optional) L4 Flagsflags
(Optional) L4 Flagsflag_val
Command Mode
• /exec/elamns/sel7
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3920
S Commandsset inner l4
Page 4065
set inner l4set inner l4 { l4-type <l4_type> | src-port <sport> | dst-port <dport> | packet-len <pkt_len> | checksum <csum>| flags <flag_val> | tn-nonce <tn_nonce> | tn-lsb <tn_lsb> | tn-nonce-info <tn_nonce_info> | tn-lsb-info<tn_lsb_info> | vnid <vnid_val> | nd-type <nd_type> | nd-code <nd_code> | nd-flags <nd_flags> | nd-ip<nd_ip> | nonce-lb <nonce_lb> | nonce-dl <nonce_dl> | nonce-e <nonce_e> | nonce-sp <nonce_sp> | nonce-dp<nonce_dp> | nonce-dre <nonce_dre> | sclass <sclass> | lsb-m <lsb_m> | lsb-lb-tag <lsb_lb_tag> | lsb-lb-metric<lsb_lb_metric> } +
Syntax Description
Setup Triggerset
Mask and Match By Inner Packet Fieldsinner
L4 Fieldsl4
L4 Type - 0:TCP 1:UDP 2:IVXLAN 3:VXLAN 4:NVGRE 7:NDl4-type
L4 Type Value - 0:TCP 1:UDP 2:IVXLAN 3:VXLAN 4:NVGRE 7:NDl4_type
Source Port Informationsrc-port
Source Portsport
Destination Port Informationdst-port
Destination Portdport
Packet Lengthpacket-len
Packet Lengthpkt_len
Checksumchecksum
Checksumcsum
L4 Flagsflags
L4 Flagsflag_val
Nonce validtn-nonce
Nonce validtn_nonce
Lsb validtn-lsb
Lsb validtn_lsb
Nonce Infotn-nonce-info
Nonce Infotn_nonce_info
Lsb Infotn-lsb-info
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3921
S Commandsset inner l4
Page 4066
Lsb Infotn_lsb_info
Virtual Network Idvnid
Virtual Network Idvnid_val
ND Typend-type
ND Typend_type
ND Codend-code
ND Codend_code
ND Flagsnd-flags
ND Flagsnd_flags
ND IPnd-ip
Nonce Load Balancenonce-lb
Nonce Load Balancenonce_lb
Nonce Don't Learnnonce-dl
Nonce Don't Learnnonce_dl
Nonce Exceptionnonce-e
Nonce Exceptionnonce_e
Nonce Src Policy appliednonce-sp
Nonce Src Policy appliednonce_sp
Nonce Dst Policy appliednonce-dp
Nonce Dst Policy appliednonce_dp
Nonce Congestion Est.nonce-dre
Nonce Congestion Est.nonce_dre
Nonce Src Classsclass
Nonce Src Classsclass
Lsb Markerlsb-m
Lsb Markerlsb_m
Lsb LB Taglsb-lb-tag
Lsb LB Taglsb_lb_tag
Lsb LB Metriclsb-lb-metric
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3922
S Commandsset inner l4
Page 4067
Lsb LB Metriclsb_lb_metric
Command Mode
• /exec/elamtah/insel7
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3923
S Commandsset inner l4
Page 4068
set inner l4set inner l4 [ { src-port <sport> | dst-port <dport> | packet-len <pkt_len> | checksum <csum> | flags <flag_val>} ] +
Syntax Description
Setup Triggerset
Mask and Match By Inner Packet Fieldsinner
L4 Fieldsl4
(Optional) Source Port Informationsrc-port
(Optional) Source Portsport
(Optional) Destination Port Informationdst-port
(Optional) Destination Portdport
(Optional) Packet Lengthpacket-len
(Optional) Packet Lengthpkt_len
(Optional) Checksumchecksum
(Optional) Checksumcsum
(Optional) L4 Flagsflags
(Optional) L4 Flagsflag_val
Command Mode
• /exec/elamns/sel4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3924
S Commandsset inner l4
Page 4069
set interface[no] set interface <iface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Output interfaceinterface
Interface nameiface
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3925
S Commandsset interface
Page 4070
set interval find-new-host[no] set interval find-new-host <val>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set vmtracker optionsset
Set the polling intervalinterval
Set interval for the new host searching timerfind-new-host
The host search interval value in seconds (0 to disable)val
Command Mode
• /exec/configure/vmt-conn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3926
S Commandsset interval find-new-host
Page 4071
set interval sync-full-info[no] set interval sync-full-info <val>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set vmtracker optionsset
Set the polling intervalinterval
Set interval for syncing complete info from hostsync-full-info
The sync info interval value in seconds (0 to disable)val
Command Mode
• /exec/configure/vmt-conn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3927
S Commandsset interval sync-full-info
Page 4072
set ip address prefix-list[no] set ip address prefix-list <name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IP featuresip
Specify IP addressaddress
IP prefix-listprefix-list
Name of prefix listname
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3928
S Commandsset ip address prefix-list
Page 4073
set ip default next-hop[no] set ip default next-hop [ recursive ] { load-share | <addr1> + [ load-share ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IP featuresip
(Optional) Use recursive lookuprecursive
Set default next-hopdefault
Next hop addressnext-hop
IP address of next hopaddr1
Enables load sharingload-share
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3929
S Commandsset ip default next-hop
Page 4074
set ip default next-hop verify-availability[no] set ip default next-hop verify-availability { <addr> [ track <object_id> ] } [ load-share ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IP featuresip
Set default next-hopdefault
Next hop addressnext-hop
Verify the reachability of the tracked objectverify-availability
IP address of next hopaddr
(Optional) The tracking method is tracktrack
(Optional) Object number that the tracking subsystem is trackingobject_id
(Optional) Enables load sharingload-share
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3930
S Commandsset ip default next-hop verify-availability
Page 4075
set ip next-hop[no] set ip next-hop [ recursive ] { [ <addr1> + ] { { [ drop-on-fail ] [ load-share ] [ force-order ] } | { [drop-on-fail ] [ force-order ] [ load-share ] } | { [ load-share ] [ drop-on-fail ] [ force-order ] } | { [ load-share] [ force-order ] [ drop-on-fail ] } | { [ force-order ] [ drop-on-fail ] [ load-share ] } | { [ force-order ] [ load-share] [ drop-on-fail ] } } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IP featuresip
(Optional) Use recursive lookuprecursive
Next hop addressnext-hop
(Optional) IP address of next hopaddr1
(Optional) Enables load sharingload-share
(Optional) Maintains next-hop order as per cli configforce-order
(Optional) Drop packets when next-hop unreachabledrop-on-fail
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3931
S Commandsset ip next-hop
Page 4076
set ip next-hop peer-address[no] set ip next-hop peer-address
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IP featuresip
Next hop addressnext-hop
Use peer address (for BGP only)peer-address
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3932
S Commandsset ip next-hop peer-address
Page 4077
set ip next-hop redist-unchanged[no] set ip next-hop redist-unchanged
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IP featuresip
Next hop addressnext-hop
Use unchanged address during redistribution (for BGP session only)redist-unchanged
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3933
S Commandsset ip next-hop redist-unchanged
Page 4078
set ip next-hop unchanged[no] set ip next-hop unchanged
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IP featuresip
Next hop addressnext-hop
Use unchanged address (for eBGP session only)unchanged
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3934
S Commandsset ip next-hop unchanged
Page 4079
set ip next-hop verify-availability[no] set ip next-hop verify-availability { <addr> [ track <object_id> ] } [ load-share ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IP featuresip
Next hop addressnext-hop
Verify the reachability of the tracked objectverify-availability
IP address of next hopaddr
(Optional) The tracking method is tracktrack
(Optional) Object number that the tracking subsystem is trackingobject_id
(Optional) Enables load sharingload-share
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3935
S Commandsset ip next-hop verify-availability
Page 4080
set ip precedence{ set ip precedence { <value> | <name> } } | { no set ip precedence [ <value> | <name> ] }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IP featuresip
Set precedence fieldprecedence
Precedence valuevalue
Precedence valuename
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3936
S Commandsset ip precedence
Page 4081
set ipv6 address prefix-list[no] set ipv6 address prefix-list <name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IPv6 featuresipv6
Specify IP addressaddress
IPv6 prefix-listprefix-list
Name of prefix listname
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3937
S Commandsset ipv6 address prefix-list
Page 4082
set ipv6 default next-hop[no] set ipv6 default next-hop [ recursive ] { load-share | <addr1> + [ load-share ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IPv6 featuresipv6
(Optional) Use recursive lookuprecursive
Set default next-hopdefault
Next hop addressnext-hop
Enables load sharingload-share
addr1
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3938
S Commandsset ipv6 default next-hop
Page 4083
set ipv6 default next-hop verify-availability[no] set ipv6 default next-hop verify-availability { <addr> [ track <object_id> ] } [ load-share ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IPv6 featuresipv6
Next hop addressnext-hop
Set default next-hopdefault
Verify the reachability of the tracked objectverify-availability
(Optional) The tracking method is tracktrack
(Optional) Object number that the tracking subsystem is trackingobject_id
(Optional) Enables load sharingload-share
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3939
S Commandsset ipv6 default next-hop verify-availability
Page 4084
set ipv6 next-hop[no] set ipv6 next-hop { [ <addr> + ] { { [ drop-on-fail ] [ load-share ] [ force-order ] } | { [ drop-on-fail ] [force-order ] [ load-share ] } | { [ load-share ] [ drop-on-fail ] [ force-order ] } | { [ load-share ] [ force-order] [ drop-on-fail ] } | { [ force-order ] [ drop-on-fail ] [ load-share ] } | { [ force-order ] [ load-share ] [ drop-on-fail] } } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IPv6 featuresipv6
Next hop ipv6 addressnext-hop
(Optional) Enables load sharingload-share
(Optional) Enables Next-hop ordering as per cliforce-order
(Optional) Drop packets when next-hop unreachabledrop-on-fail
(Optional)addr
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3940
S Commandsset ipv6 next-hop
Page 4085
set ipv6 next-hop peer-address[no] set ipv6 next-hop peer-address
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IPv6 featuresipv6
Next hop addressnext-hop
Use peer address (for BGP only)peer-address
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3941
S Commandsset ipv6 next-hop peer-address
Page 4086
set ipv6 next-hop redist-unchanged[no] set ipv6 next-hop redist-unchanged
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IPv6 featuresipv6
Next hop addressnext-hop
Use unchanged address during redistribution (for BGP session only)redist-unchanged
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3942
S Commandsset ipv6 next-hop redist-unchanged
Page 4087
set ipv6 next-hop unchanged[no] set ipv6 next-hop unchanged
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IPv6 featuresipv6
Next hop addressnext-hop
Use unchanged address (for eBGP session only)unchanged
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3943
S Commandsset ipv6 next-hop unchanged
Page 4088
set ipv6 next-hop verify-availability[no] set ipv6 next-hop verify-availability { <addr> [ track <object_id> ] } [ load-share ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IPv6 featuresipv6
Next hop addressnext-hop
Verify the reachability of the tracked objectverify-availability
(Optional) The tracking method is tracktrack
(Optional) Object number that the tracking subsystem is trackingobject_id
(Optional) Enables load sharingload-share
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3944
S Commandsset ipv6 next-hop verify-availability
Page 4089
set ipv6 precedence{ set ipv6 precedence { <value> | <name> } } | { no set ipv6 precedence [ <value> | <name> ] }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
Configure IPv6 featuresipv6
Set precedence fieldprecedence
Precedence valuevalue
Precedence valuename
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3945
S Commandsset ipv6 precedence
Page 4090
set label-index{ { set label-index <value> } | { no set label-index [ <value> ] } }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
Set Segment Routing (SR) label index of routelabel-index
Segment Routing (SR) label indexvalue
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3946
S Commandsset label-index
Page 4091
set level level-1 level-1-2 level-2{ set level { level-1 | level-1-2 | level-2 } } | { no set level [ level-1 | level-1-2 | level-2 ] }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
Where to import routelevel
Import into a level-1 arealevel-1
Import into level-1 and level-2level-1-2
Import into level-2 sub-domainlevel-2
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3947
S Commandsset level level-1 level-1-2 level-2
Page 4092
set local-preference{ set local-preference <pref> | no set local-preference [ <pref> ] }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
BGP local preference path attributelocal-preference
Preference valuepref
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3948
S Commandsset local-preference
Page 4093
set metric{ set metric <metric0> [ <metric1> <metric2> <metric3> <metric4> ] } | { no set metric [ <metric0> [ <metric1><metric2> <metric3> <metric4> ] ] }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
Set metric for destination routing protocolmetric
[+/-] Metric value or Bandwidth in Kbits per secondmetric0
(Optional) IGRP delay metricmetric1
(Optional) IGRP reliability metric where 255 is 100% reliablemetric2
(Optional) IGRP Effective bandwidth metric (Loading) 255 is 100%metric3
(Optional) IGRP MTU of the pathmetric4
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3949
S Commandsset metric
Page 4094
set nssa-only[no] set nssa-only
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
OSPF NSSA Areasnssa-only
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3950
S Commandsset nssa-only
Page 4095
set origin egp{ set origin egp <as> } | { no set origin egp <as> }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
BGP origin codeorigin
remote EGPegp
AS numberas
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3951
S Commandsset origin egp
Page 4096
set origin egp igp incomplete{ set origin { egp | igp | incomplete } } | { no set origin [ { egp | igp | incomplete } ] }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
BGP origin codeorigin
remote EGPegp
local IGPigp
unknown heritageincomplete
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3952
S Commandsset origin egp igp incomplete
Page 4097
set outer arpset outer arp { target-ip-addr <tipaddr> | target-mac-addr <tmac> | source-ip-addr <sipaddr> | source-mac-addr<smac> | opcode <opcode_val> | prot-addr-len <prot_addr_len> | hw-addr-len <hw_addr_len> | protocol-type<prot_type> | hardware-type <hw_type> | ether-type <etype> | payload-len <pyld_len> } +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
ARP Fieldsarp
ARP Target IP Addresstarget-ip-addr
ARP Target IP Addresstipaddr
ARP Target MAC Addresstarget-mac-addr
ARP Target MAC Addresstmac
ARP Source IP Addresssource-ip-addr
ARP Source IP Addresssipaddr
ARP Source MAC Addresssource-mac-addr
ARP Source MAC Addresssmac
ARP Opcodeopcode
ARP Opcodeopcode_val
ARP Protocol Address Lengthprot-addr-len
ARP Protocol Address Lengthprot_addr_len
ARP Hardware Address Lengthhw-addr-len
ARP Hardware Address Lengthhw_addr_len
ARP Protocol Typeprotocol-type
ARP Protocol Typeprot_type
ARP Hardware Typehardware-type
ARP Hardware Typehw_type
ARP Ether Type - 0x0806 -> ARP 0x8035 -> RARPether-type
ARP Ether Type - 0x0806 -> ARP 0x8035 -> RARPetype
ARP Payload Lengthpayload-len
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3953
S Commandsset outer arp
Page 4098
ARP Payload Lengthpyld_len
Command Mode
• /exec/elamtah/insel6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3954
S Commandsset outer arp
Page 4099
set outer arpset { outer | inner } arp { target-ip-addr <tipaddr> | target-mac-addr <tmac> | source-ip-addr <sipaddr> |source-mac-addr <smac> | opcode <opcode_val> | prot-addr-len <prot_addr_len> | hw-addr-len <hw_addr_len>| protocol-type <prot_type> | hardware-type <hw_type> | ether-type <etype> | payload-len <pyld_len> } +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
Mask and Match By Inner Packet Fieldsinner
ARP Fieldsarp
ARP Target IP Addresstarget-ip-addr
ARP Target IP Addresstipaddr
ARP Target MAC Addresstarget-mac-addr
ARP Target MAC Addresstmac
ARP Source IP Addresssource-ip-addr
ARP Source IP Addresssipaddr
ARP Source MAC Addresssource-mac-addr
ARP Source MAC Addresssmac
ARP Opcodeopcode
ARP Opcodeopcode_val
ARP Protocol Address Lengthprot-addr-len
ARP Protocol Address Lengthprot_addr_len
ARP Hardware Address Lengthhw-addr-len
ARP Hardware Address Lengthhw_addr_len
ARP Protocol Typeprotocol-type
ARP Protocol Typeprot_type
ARP Hardware Typehardware-type
ARP Hardware Typehw_type
ARP Ether Type - 0x0806 -> ARP 0x8035 -> RARPether-type
ARP Ether Type - 0x0806 -> ARP 0x8035 -> RARPetype
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3955
S Commandsset outer arp
Page 4100
ARP Payload Lengthpayload-len
ARP Payload Lengthpyld_len
Command Mode
• /exec/elamtah/insel9
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3956
S Commandsset outer arp
Page 4101
set outer fcoeset outer fcoe { pyld-len <pyld_len> | ether-type <etype> | esof <esof> | r_ctl <r_ctl> | d_id <d_id> | cs_ctl<cs_ctl> | s_id <s_id> | fc_type <fc_type> | f_ctl <f_ctl> | df_ctl <df_ctl> | ox_id <ox_id> | rx_id <rx_id> |pyld0 <pyld0> | pyld1 <pyld1> | pyld2 <pyld2> | pyld3 <pyld3> | vft_vld <vft_vld> | vft_type <vft_type> |vft_prio <vft_prio> | vft_vfid <vft_vfid> | vft_hopct <vft_hopct> } +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
FCoE Fieldsfcoe
Payload Lengthpyld-len
Payload Lengthpyld_len
FCoE Ether Type - 0x8906ether-type
FCoE Ether Type - 0x8906etype
ESOFesof
ESOF Valueesof
R_CTLr_ctl
R_CTL valuer_ctl
D_IDd_id
D_ID valued_id
CS_CTLcs_ctl
CS_CTL valuecs_ctl
S_IDs_id
S_ID values_id
FC_TYPEfc_type
FC_TYPE valuefc_type
F_CTLf_ctl
F_CTL valuef_ctl
DF_CTLdf_ctl
DF_CTL valuedf_ctl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3957
S Commandsset outer fcoe
Page 4102
OxIDox_id
OxID valueox_id
RxIDrx_id
RxID valuerx_id
First 4 bytes of payloadpyld0
First 4 bytes of payload valuepyld0
Second 4 bytes of payloadpyld1
Second 4 bytes of payload valuepyld1
Third 4 bytes of payloadpyld2
Third 4 bytes of payload valuepyld2
Fourth 4 bytes of payloadpyld3
Fourth 4 bytes of payload valuepyld3
VFT_VLDvft_vld
VFT_VLD valuevft_vld
VFT_TYPEvft_type
VFT_TYPE valuevft_type
VFT_PRIOvft_prio
VFT_PRIO valuevft_prio
VFT_VFIDvft_vfid
VFT_VFID valuevft_vfid
VFT_HOPCTvft_hopct
VFT_HOPCT valuevft_hopct
Command Mode
• /exec/elamtah/insel6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3958
S Commandsset outer fcoe
Page 4103
set outer ipv4set outer ipv4 { pyld-len <pyld_len> | version <ver> | header-len <hlen> | dscp <dscp_val> | ecn <ecn_val>| packet-len <pkt_len> | more-frags <mf> | fragment-off <fragoff> | ttl <ttl_val> | next-protocol <nproto> |checksum <csum> | src_ip <sip> | dst_ip <dip> } +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
IPv4 Fieldsipv4
Payload Lengthpyld-len
Payload Lengthpyld_len
Versionversion
Versionver
Header Lengthheader-len
Header Lengthhlen
Diff. Serv. Code Pointdscp
Diff. Serv. Code Pointdscp_val
Explicit Congestion Ntfnecn
Explicit Congestion Ntfnecn_val
Packet Total Lengthpacket-len
Packet Total Lengthpkt_len
More Fragments Availablemore-frags
More Fragments Availablemf
Fragments Offsetfragment-off
Fragments Offsetfragoff
Time to Livettl
Time to Livettl_val
Next Protocolnext-protocol
Next Protocolnproto
Checksumchecksum
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3959
S Commandsset outer ipv4
Page 4104
Checksumcsum
Source IP Addresssrc_ip
Source IP Addresssip
Destination IP Addressdst_ip
Destination IP Addressdip
Command Mode
• /exec/elamtah/insel6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3960
S Commandsset outer ipv4
Page 4105
set outer ipv4set { outer | inner } ipv4 { pyld-len <pyld_len> | version <ver> | header-len <hlen> | dscp <dscp_val> | ecn<ecn_val> | packet-len <pkt_len> | more-frags <mf> | fragment-off <fragoff> | ttl <ttl_val> | next-protocol<nproto> | checksum <csum> | src_ip <sip> | dst_ip <dip> } +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
Mask and Match By Inner Packet Fieldsinner
IPv4 Fieldsipv4
Payload Lengthpyld-len
Payload Lengthpyld_len
Versionversion
Versionver
Header Lengthheader-len
Header Lengthhlen
Diff. Serv. Code Pointdscp
Diff. Serv. Code Pointdscp_val
Explicit Congestion Ntfnecn
Explicit Congestion Ntfnecn_val
Packet Total Lengthpacket-len
Packet Total Lengthpkt_len
More Fragments Availablemore-frags
More Fragments Availablemf
Fragments Offsetfragment-off
Fragments Offsetfragoff
Time to Livettl
Time to Livettl_val
Next Protocolnext-protocol
Next Protocolnproto
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3961
S Commandsset outer ipv4
Page 4106
Checksumchecksum
Checksumcsum
Source IP Addresssrc_ip
Source IP Addresssip
Destination IP Addressdst_ip
Destination IP Addressdip
Command Mode
• /exec/elamtah/insel9
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3962
S Commandsset outer ipv4
Page 4107
set outer ipv4set outer ipv4 [ { l3-type <l3_type> | pyld-len <pyld_len> | v6-vld <v6_vld> | version <ver> | header-len<hlen> | dscp <dscp_val> | ecn <ecn_val> | packet-len <pkt_len> | more-frags <mf> | fragment-off <fragoff>| ttl <ttl_val> | next-protocol <nproto> | checksum <csum> | src_ip <sip> | dst_ip <dip> } ] +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
IPv4 Fieldsipv4
(Optional) L3 Packet Typel3-type
(Optional) L3 Packet Typel3_type
(Optional) Payload Lengthpyld-len
(Optional) Payload Lengthpyld_len
(Optional) IPv6 Valid Informationv6-vld
(Optional) IPv6 Valid Informationv6_vld
(Optional) Versionversion
(Optional) Versionver
(Optional) Header Lengthheader-len
(Optional) Header Lengthhlen
(Optional) Diff. Serv. Code Pointdscp
(Optional) Diff. Serv. Code Pointdscp_val
(Optional) Explicit Congestion Ntfnecn
(Optional) Explicit Congestion Ntfnecn_val
(Optional) Packet Total Lengthpacket-len
(Optional) Packet Total Lengthpkt_len
(Optional) More Fragments Availablemore-frags
(Optional) More Fragments Availablemf
(Optional) Fragments Offsetfragment-off
(Optional) Fragments Offsetfragoff
(Optional) Time to Livettl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3963
S Commandsset outer ipv4
Page 4108
(Optional) Time to Livettl_val
(Optional) Next(L4) Protocolnext-protocol
(Optional) Next(L4) Protocolnproto
(Optional) Checksumchecksum
(Optional) Checksumcsum
(Optional) Source IP Addresssrc_ip
(Optional) Source IP Addresssip
(Optional) Destination IP Addressdst_ip
(Optional) Destination IP Addressdip
Command Mode
• /exec/elamns/sel3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3964
S Commandsset outer ipv4
Page 4109
set outer ipv6 src_ipset { outer | inner } ipv6 { src_ip <sip> | dst_ip <dip> } +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
Mask and Match By Inner Packet Fieldsinner
IPv6 Fieldsipv6
Source IP Addresssrc_ip
Destination IP Addressdst_ip
Command Mode
• /exec/elamtah/insel9
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3965
S Commandsset outer ipv6 src_ip
Page 4110
set outer ipv6 src_ipset outer ipv6 { src_ip <sip> | dst_ip <dip> } +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
IPv6 Fieldsipv6
Source IP Addresssrc_ip
Destination IP Addressdst_ip
Command Mode
• /exec/elamtah/insel6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3966
S Commandsset outer ipv6 src_ip
Page 4111
set outer l2set { outer | inner } l2 { snap_vld <snap_vld> | cntag_vld <cntag_vld> | qtag_vld <qtag_vld> | vlan <vlan_id>| cos <cos_val> | cfi <cfi_vld> | vntag_vld <vntag_vld> | vntag_svif <vntag_svif> | vntag_dvif <vntag_dvif>| vntag_looped <vntag_loop> | vntag_pointer <vntag_p> | src_mac <smac> | dst_mac <dmac> } +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
Mask and Match By Inner Packet Fieldsinner
All Layer 2 Fieldsl2
SNAP Header Information Validsnap_vld
SNAP Header Information Validsnap_vld
CNTag Information Validcntag_vld
CNTag Information Validcntag_vld
VLAN Tag Information Validqtag_vld
VLAN Tag Information Validqtag_vld
VLAN Id (Present only in case of FEX)vlan
VLAN Idvlan_id
Class of Servicecos
Class of Service Typecos_val
CFI Settingcfi
CFI Setting Validcfi_vld
VNTAG Information Validvntag_vld
VNTAG Information Validvntag_vld
VNTAG Source vifvntag_svif
VNTAG Source vifvntag_svif
VNTAG Destination vifvntag_dvif
VNTAG Destination vifvntag_dvif
VNTAG Header Looped Validvntag_looped
VNTAG Header Looped Validvntag_loop
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3967
S Commandsset outer l2
Page 4112
VNTAG Header Pointer Validvntag_pointer
VNTAG Header Pointer Validvntag_p
Source MAC Addresssrc_mac
Source MAC Address Valuesmac
Destination MAC Addressdst_mac
Destination MAC Address Valuedmac
Command Mode
• /exec/elamtah/insel8
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3968
S Commandsset outer l2
Page 4113
set outer l2set outer l2 { snap_vld <snap_vld> | cntag_vld <cntag_vld> | qtag_vld <qtag_vld> | vlan <vlan_id> | cos<cos_val> | cfi <cfi_vld> | vntag_vld <vntag_vld> | vntag_svif <vntag_svif> | vntag_dvif <vntag_dvif> |vntag_looped <vntag_loop> | vntag_pointer <vntag_p> | src_mac <smac> | dst_mac <dmac> } +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
All Layer 2 Fieldsl2
SNAP Header Information Validsnap_vld
SNAP Header Information Validsnap_vld
CNTag Information Validcntag_vld
CNTag Information Validcntag_vld
VLAN Tag Information Validqtag_vld
VLAN Tag Information Validqtag_vld
VLAN Id (Present only in case of FEX)vlan
VLAN Idvlan_id
Class of Servicecos
Class of Service Typecos_val
CFI Settingcfi
CFI Setting Validcfi_vld
VNTAG Information Validvntag_vld
VNTAG Information Validvntag_vld
VNTAG Source vifvntag_svif
VNTAG Source vifvntag_svif
VNTAG Destination vifvntag_dvif
VNTAG Destination vifvntag_dvif
VNTAG Header Looped Validvntag_looped
VNTAG Header Looped Validvntag_loop
VNTAG Header Pointer Validvntag_pointer
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3969
S Commandsset outer l2
Page 4114
VNTAG Header Pointer Validvntag_p
Source MAC Addresssrc_mac
Source MAC Address Valuesmac
Destination MAC Addressdst_mac
Destination MAC Address Valuedmac
Command Mode
• /exec/elamtah/insel6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3970
S Commandsset outer l2
Page 4115
set outer l2set outer l2 [ { snap_vld <snap_vld> | cntag_vld <cntag_vld> | qtag_vld <qtag_vld> | vlan <vlan_id> | cos<cos_val> | cfi <cfi_vld> | vntag_vld <vntag_vld> | vntag_svif <vntag_svif> | vntag_dvif <vntag_dvif> |vntag_looped <vntag_loop> | vntag_pointer <vntag_p> | src_mac <smac> | dst_mac <dmac> } ] +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
All Layer 2 Fieldsl2
(Optional) SNAP Header Information Validsnap_vld
(Optional) SNAP Header Information Validsnap_vld
(Optional) CNTag Information Validcntag_vld
(Optional) CNTag Information Validcntag_vld
(Optional) VLAN Tag Information Validqtag_vld
(Optional) VLAN Tag Information Validqtag_vld
(Optional) VLAN Id (Present only in case of FEX)vlan
(Optional) VLAN Idvlan_id
(Optional) Class of Servicecos
(Optional) Class of Service Typecos_val
(Optional) CFI Settingcfi
(Optional) CFI Setting Validcfi_vld
(Optional) VNTAG Information Validvntag_vld
(Optional) VNTAG Information Validvntag_vld
(Optional) VNTAG Source vifvntag_svif
(Optional) VNTAG Source vifvntag_svif
(Optional) VNTAG Destination vifvntag_dvif
(Optional) VNTAG Destination vifvntag_dvif
(Optional) VNTAG Header Looped Validvntag_looped
(Optional) VNTAG Header Looped Validvntag_loop
(Optional) VNTAG Header Pointer Validvntag_pointer
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3971
S Commandsset outer l2
Page 4116
(Optional) VNTAG Header Pointer Validvntag_p
(Optional) Source MAC Addresssrc_mac
(Optional) Source MAC Address Valuesmac
(Optional) Destination MAC Addressdst_mac
(Optional) Destination MAC Address Valuedmac
Command Mode
• /exec/elamns/sel3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3972
S Commandsset outer l2
Page 4117
set outer l2 hg2set outer l2 hg2 [ { hg2_vid <hg2_vlan> | hg2_ppd_type <hg2_ppd_type> | hg2_mirror <hg2_mirror> |hg2_opcode <hg2_opcode> | hg2_dstpid <hg2_dpid> | hg2_dstmod <hg2_dmod> | hg2_srcpid <hg2_spid>| hg2_srcmod <hg2_smod> | hg2_l3vld <hg2_l3_vld> | hg2_tc <hg2_tc> | hg2_dp <hg2_dp> | hg2_mcast<hg2_mcast_vld> | hg2-vld <hg2_vld> | hg2-cos <hg2_cos> } ] +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
All Layer 2 Fieldsl2
High Gig2 Fieldshg2
(Optional) High Gig2 VLAN Taghg2_vid
(Optional) High Gig2 VLAN Tag Informationhg2_vlan
(Optional) High Gig2 Packet Processing Descriptorhg2_ppd_type
(Optional) High Gig2 Packet Processing Descriptorhg2_ppd_type
(Optional) High Gig2 Packet Mirror Informationhg2_mirror
(Optional) High Gig2 Packet Mirror Informationhg2_mirror
(Optional) High Gig2 Packet Typehg2_opcode
(Optional) High Gig2 Packet Typehg2_opcode
(Optional) High Gig2 Destination Port IDhg2_dstpid
(Optional) High Gig2 Destination Port IDhg2_dpid
(Optional) High Gig2 Destination Module IDhg2_dstmod
(Optional) High Gig2 Destination Module IDhg2_dmod
(Optional) High Gig2 Source Port IDhg2_srcpid
(Optional) High Gig2 Source Port IDhg2_spid
(Optional) High Gig2 Souce Module IDhg2_srcmod
(Optional) High Gig2 Souce Module IDhg2_smod
(Optional) High Gig2 Packet L3 Switchedhg2_l3vld
(Optional) High Gig2 Packet L3 Switchedhg2_l3_vld
(Optional) High Gig2 Packet Traffic Classhg2_tc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3973
S Commandsset outer l2 hg2
Page 4118
(Optional) High Gig2 Packet Traffic Classhg2_tc
(Optional) High Gig2 Drop Precedencehg2_dp
(Optional) High Gig2 Drop Precedencehg2_dp
(Optional) High Gig2 MultiCast Forwarding Informationhg2_mcast
(Optional) High Gig2 Multicast Forwarding Informationhg2_mcast_vld
(Optional) High Gig2 Valid Informationhg2-vld
(Optional) High Gig2 Valid Informationhg2_vld
(Optional) High Gig2 CoS Informationhg2-cos
(Optional) High Gig2 CoS Informationhg2_cos
Command Mode
• /exec/elamns/sel3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3974
S Commandsset outer l2 hg2
Page 4119
set outer l4set outer l4 [ { src-port <sport> | dst-port <dport> | packet-len <pkt_len> | checksum <csum> | flags <flag_val>} ] +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
L4 Fieldsl4
(Optional) Source Port Informationsrc-port
(Optional) Source Portsport
(Optional) Destination Port Informationdst-port
(Optional) Destination Portdport
(Optional) Packet Lengthpacket-len
(Optional) Packet Lengthpkt_len
(Optional) Checksumchecksum
(Optional) Checksumcsum
(Optional) L4 Flagsflags
(Optional) L4 Flagsflag_val
Command Mode
• /exec/elamns/sel3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3975
S Commandsset outer l4
Page 4120
set outer l4set outer l4 { l4-type <l4_type> | src-port <sport> | dst-port <dport> | packet-len <pkt_len> | checksum <csum>| flags <flag_val> | tn-nonce <tn_nonce> | tn-lsb <tn_lsb> | tn-nonce-info <tn_nonce_info> | tn-lsb-info<tn_lsb_info> | vnid <vnid_val> | nd-type <nd_type> | nd-code <nd_code> | nd-flags <nd_flags> | nd-ip<nd_ip> | nonce-lb <nonce_lb> | nonce-dl <nonce_dl> | nonce-e <nonce_e> | nonce-sp <nonce_sp> | nonce-dp<nonce_dp> | nonce-dre <nonce_dre> | sclass <sclass> | lsb-m <lsb_m> | lsb-lb-tag <lsb_lb_tag> | lsb-lb-metric<lsb_lb_metric> } +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
L4 Fieldsl4
L4 Type - 0:TCP 1:UDP 2:IVXLAN 3:VXLAN 4:NVGRE 7:NDl4-type
L4 Type Value - 0:TCP 1:UDP 2:IVXLAN 3:VXLAN 4:NVGRE 7:NDl4_type
Source Port Informationsrc-port
Source Portsport
Destination Port Informationdst-port
Destination Portdport
Packet Lengthpacket-len
Packet Lengthpkt_len
Checksumchecksum
Checksumcsum
L4 Flags 123flags
L4 Flagsflag_val
Nonce validtn-nonce
Nonce validtn_nonce
Lsb validtn-lsb
Lsb validtn_lsb
Nonce Infotn-nonce-info
Nonce Infotn_nonce_info
Lsb Infotn-lsb-info
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3976
S Commandsset outer l4
Page 4121
Lsb Infotn_lsb_info
Virtual Network Idvnid
Virtual Network Idvnid_val
ND Typend-type
ND Typend_type
ND Codend-code
ND Codend_code
ND Flagsnd-flags
ND Flagsnd_flags
ND IPnd-ip
Nonce Load Balancenonce-lb
Nonce Load Balancenonce_lb
Nonce Don't Learnnonce-dl
Nonce Don't Learnnonce_dl
Nonce Exceptionnonce-e
Nonce Exceptionnonce_e
Nonce Src Policy appliednonce-sp
Nonce Src Policy appliednonce_sp
Nonce Dst Policy appliednonce-dp
Nonce Dst Policy appliednonce_dp
Nonce Congestion Est.nonce-dre
Nonce Congestion Est.nonce_dre
Nonce Src Classsclass
Nonce Src Classsclass
Lsb Markerlsb-m
Lsb Markerlsb_m
Lsb LB Taglsb-lb-tag
Lsb LB Taglsb_lb_tag
Lsb LB Metriclsb-lb-metric
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3977
S Commandsset outer l4
Page 4122
Lsb LB Metriclsb_lb_metric
Command Mode
• /exec/elamtah/insel6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3978
S Commandsset outer l4
Page 4123
set outer l4set { outer | inner } l4 { l4-type <l4_type> | src-port <sport> | dst-port <dport> | packet-len <pkt_len> |checksum <csum> | flags <flag_val> | tn-nonce <tn_nonce> | tn-lsb <tn_lsb> | tn-nonce-info <tn_nonce_info>| tn-lsb-info <tn_lsb_info> | vnid <vnid_val> | nd-type <nd_type> | nd-code <nd_code> | nd-flags <nd_flags>| nd-ip <nd_ip> | nonce-lb <nonce_lb> | nonce-dl <nonce_dl> | nonce-e <nonce_e> | nonce-sp <nonce_sp> |nonce-dp <nonce_dp> | nonce-dre <nonce_dre> | sclass <sclass> | lsb-m <lsb_m> | lsb-lb-tag <lsb_lb_tag> |lsb-lb-metric <lsb_lb_metric> } +
Syntax Description
Setup Triggerset
Mask and Match By Outer Packet Fieldsouter
Mask and Match By Inner Packet Fieldsinner
L4 Fieldsl4
L4 Type - 0:TCP 1:UDP 2:IVXLAN 3:VXLAN 4:NVGRE 7:NDl4-type
L4 Type Value - 0:TCP 1:UDP 2:IVXLAN 3:VXLAN 4:NVGRE 7:NDl4_type
Source Port Informationsrc-port
Source Portsport
Destination Port Informationdst-port
Destination Portdport
Packet Lengthpacket-len
Packet Lengthpkt_len
Checksumchecksum
Checksumcsum
L4 Flags 123flags
L4 Flagsflag_val
Nonce validtn-nonce
Nonce validtn_nonce
Lsb validtn-lsb
Lsb validtn_lsb
Nonce Infotn-nonce-info
Nonce Infotn_nonce_info
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3979
S Commandsset outer l4
Page 4124
Lsb Infotn-lsb-info
Lsb Infotn_lsb_info
Virtual Network Idvnid
Virtual Network Idvnid_val
ND Typend-type
ND Typend_type
ND Codend-code
ND Codend_code
ND Flagsnd-flags
ND Flagsnd_flags
ND IPnd-ip
Nonce Load Balancenonce-lb
Nonce Load Balancenonce_lb
Nonce Don't Learnnonce-dl
Nonce Don't Learnnonce_dl
Nonce Exceptionnonce-e
Nonce Exceptionnonce_e
Nonce Src Policy appliednonce-sp
Nonce Src Policy appliednonce_sp
Nonce Dst Policy appliednonce-dp
Nonce Dst Policy appliednonce_dp
Nonce Congestion Est.nonce-dre
Nonce Congestion Est.nonce_dre
Nonce Src Classsclass
Nonce Src Classsclass
Lsb Markerlsb-m
Lsb Markerlsb_m
Lsb LB Taglsb-lb-tag
Lsb LB Taglsb_lb_tag
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3980
S Commandsset outer l4
Page 4125
Lsb LB Metriclsb-lb-metric
Lsb LB Metriclsb_lb_metric
Command Mode
• /exec/elamtah/insel10
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3981
S Commandsset outer l4
Page 4126
set path-selection advertise[no] set path-selection { all | best2 | backup | multipaths | best-external | group-best } advertise
Syntax Description
(Optional) Negate a command or set its defaultsno
Set values in destination routing protocolset
Path selection criteria for BGPpath-selection
Specifies all BGP pathsall
Specifies best 2 BGP pathsbest2
Specifies best + backup BGP pathsbackup
Specifies multipaths BGP pathsmultipaths
Specifies best-external BGP paths TBDbest-external
Specifies group-best BGP paths TBDgroup-best
Advertise add paths to its peers if receive capability enabledadvertise
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3982
S Commandsset path-selection advertise
Page 4127
set pktrwset pktrw { spare <spare> | cap_access <cap_access> | bounce <bounce> | dst_vnic_if <dst_vnic_if> | src_vnic_if<src_vnic_if> | pif_block_type <pif_block_type> | epg_out <epg_out> | epg_in <epg_in> | sup_qnum<sup_qnum> | sup_code <sup_code> | ecn_coi <ecn_coi> | ecn_cio <ecn_cio> | ttl_coi <ttl_coi> | ttl_cio<ttl_cio> | qos_map_idx <qos_map_idx> | lat_update <lat_update> | lat_index <lat_index> | dclass <dclass>| sclass <sclass> | ol_fb_metric <ol_fb_metric> | ol_fb_vpath <ol_fb_vpath> | ol_dre <ol_dre> | ol_vpath<ol_vpath> | ol_dp <ol_dp> | ol_sp <ol_sp> | ol_e <ol_e> | ol_dl <ol_dl> | ol_lb <ol_lb> | ol_mark <ol_mark>| ol_udp_sp <ol_udp_sp> | ol_ecn <ol_ecn> | nat_idx <nat_idx> | nat_vld <nat_vld> | dst_addr1 <dst_addr1>| dst_addr0 <dst_addr0> | adj_vld <adj_vld> | encap_l2_idx <encap_l2_idx> | encap_pcid <encap_pcid> |encap_idx <encap_idx> | encap_vld <encap_vld> | my_pcid <my_pcid> | my_tep_idx <my_tep_idx> | fwd_op<fwd_op> | orig_encap_type <orig_encap_type> | pkt_type <pkt_type> | len_type <len_type> | cap_1588<cap_1588> | pktid <pktid> | srcid <srcid> | tstmp <tstmp> | pktfmt1_inner <pktfmt1_inner> | pktfmt1_l3<pktfmt1_l3> | pktfmt1_l3_type <pktfmt1_l3_type> | pktfmt1_mpls_null <pktfmt1_mpls_null> | pktfmt1_snap<pktfmt1_snap> | pktfmt1_cntag <pktfmt1_cntag> | pktfmt1_ttag <pktfmt1_ttag> | pktfmt1_cmd_dgt<pktfmt1_cmd_dgt> | pktfmt1_cmd_sgt <pktfmt1_cmd_sgt> | pktfmt1_cdce <pktfmt1_cdce> | pktfmt1_trill<pktfmt1_trill> | pktfmt1_qtag2 <pktfmt1_qtag2> | pktfmt1_qtag1 <pktfmt1_qtag1> | pktfmt1_qtag0<pktfmt1_qtag0> | pktfmt1_ivntag <pktfmt1_ivntag> | pktfmt1_vntag <pktfmt1_vntag> | pktfmt1_ce<pktfmt1_ce> | pktfmt1_ieth <pktfmt1_ieth> | pktfmt1_higig2 <pktfmt1_higig2> | pktfmt0_inner<pktfmt0_inner> | pktfmt0_l3 <pktfmt0_l3> | pktfmt0_l3_type <pktfmt0_l3_type> | pktfmt0_mpls_null<pktfmt0_mpls_null> | pktfmt0_snap <pktfmt0_snap> | pktfmt0_cntag <pktfmt0_cntag> | pktfmt0_ttag<pktfmt0_ttag> | pktfmt0_cmd_dgt <pktfmt0_cmd_dgt> | pktfmt0_cmd_sgt <pktfmt0_cmd_sgt> | pktfmt0_cdce<pktfmt0_cdce> | pktfmt0_trill <pktfmt0_trill> | pktfmt0_qtag2 <pktfmt0_qtag2> | pktfmt0_qtag1<pktfmt0_qtag1> | pktfmt0_qtag0 <pktfmt0_qtag0> | pktfmt0_ivntag <pktfmt0_ivntag> | pktfmt0_vntag<pktfmt0_vntag> | pktfmt0_ce <pktfmt0_ce> | pktfmt0_ieth <pktfmt0_ieth> | pktfmt0_higig2 <pktfmt0_higig2>} +
Syntax Description
Setup Triggerset
All pktrw fieldspktrw
Sparespare
Sparespare
Cap_Accesscap_access
Cap_Accesscap_access
Bouncebounce
Bouncebounce
Dst_Vnic_Ifdst_vnic_if
Dst_Vnic_Ifdst_vnic_if
Src_Vnic_Ifsrc_vnic_if
Src_Vnic_Ifsrc_vnic_if
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3983
S Commandsset pktrw
Page 4128
Pif_Block_Typepif_block_type
Pif_Block_Typepif_block_type
Epg_Outepg_out
Epg_Outepg_out
Epg_Inepg_in
Epg_Inepg_in
Sup_Qnumsup_qnum
Sup_Qnumsup_qnum
Sup_Codesup_code
Sup_Codesup_code
Ecn_Coiecn_coi
Ecn_Coiecn_coi
Ecn_Cioecn_cio
Ecn_Cioecn_cio
Ttl_Coittl_coi
Ttl_Coittl_coi
Ttl_Ciottl_cio
Ttl_Ciottl_cio
Qos_Map_Idxqos_map_idx
Qos_Map_Idxqos_map_idx
Lat_Updatelat_update
Lat_Updatelat_update
Lat_Indexlat_index
Lat_Indexlat_index
Dclassdclass
Dclassdclass
Sclasssclass
Sclasssclass
Ol_Fb_Metricol_fb_metric
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3984
S Commandsset pktrw
Page 4129
Ol_Fb_Metricol_fb_metric
Ol_Fb_Vpathol_fb_vpath
Ol_Fb_Vpathol_fb_vpath
Ol_Dreol_dre
Ol_Dreol_dre
Ol_Vpathol_vpath
Ol_Vpathol_vpath
Ol_Dpol_dp
Ol_Dpol_dp
Ol_Spol_sp
Ol_Spol_sp
Ol_Eol_e
Ol_Eol_e
Ol_Dlol_dl
Ol_Dlol_dl
Ol_Lbol_lb
Ol_Lbol_lb
Ol_Markol_mark
Ol_Markol_mark
Ol_Udp_Spol_udp_sp
Ol_Udp_Spol_udp_sp
Ol_Ecnol_ecn
Ol_Ecnol_ecn
Nat_Idxnat_idx
Nat_Idxnat_idx
Nat_Vldnat_vld
Nat_Vldnat_vld
Dst_Addr1dst_addr1
Dst_Addr1dst_addr1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3985
S Commandsset pktrw
Page 4130
Dst_Addr0dst_addr0
Dst_Addr0dst_addr0
Adj_Vldadj_vld
Adj_Vldadj_vld
Encap_L2_Idxencap_l2_idx
Encap_L2_Idxencap_l2_idx
Encap_Pcidencap_pcid
Encap_Pcidencap_pcid
Encap_Idxencap_idx
Encap_Idxencap_idx
Encap_Vldencap_vld
Encap_Vldencap_vld
My_Pcidmy_pcid
My_Pcidmy_pcid
My_Tep_Idxmy_tep_idx
My_Tep_Idxmy_tep_idx
Fwd_Opfwd_op
Fwd_Opfwd_op
Orig_Encap_Typeorig_encap_type
Orig_Encap_Typeorig_encap_type
Pkt_Typepkt_type
Pkt_Typepkt_type
Len_Typelen_type
Len_Typelen_type
Cap_1588cap_1588
Cap_1588cap_1588
Pktidpktid
Pktidpktid
Srcidsrcid
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3986
S Commandsset pktrw
Page 4131
Srcidsrcid
Tstmptstmp
Tstmptstmp
Pktfmt1_Innerpktfmt1_inner
Pktfmt1_Innerpktfmt1_inner
Pktfmt1_L3pktfmt1_l3
Pktfmt1_L3pktfmt1_l3
Pktfmt1_L3_Typepktfmt1_l3_type
Pktfmt1_L3_Typepktfmt1_l3_type
Pktfmt1_Mpls_Nullpktfmt1_mpls_null
Pktfmt1_Mpls_Nullpktfmt1_mpls_null
Pktfmt1_Snappktfmt1_snap
Pktfmt1_Snappktfmt1_snap
Pktfmt1_Cntagpktfmt1_cntag
Pktfmt1_Cntagpktfmt1_cntag
Pktfmt1_Ttagpktfmt1_ttag
Pktfmt1_Ttagpktfmt1_ttag
Pktfmt1_Cmd_Dgtpktfmt1_cmd_dgt
Pktfmt1_Cmd_Dgtpktfmt1_cmd_dgt
Pktfmt1_Cmd_Sgtpktfmt1_cmd_sgt
Pktfmt1_Cmd_Sgtpktfmt1_cmd_sgt
Pktfmt1_Cdcepktfmt1_cdce
Pktfmt1_Cdcepktfmt1_cdce
Pktfmt1_Trillpktfmt1_trill
Pktfmt1_Trillpktfmt1_trill
Pktfmt1_Qtag2pktfmt1_qtag2
Pktfmt1_Qtag2pktfmt1_qtag2
Pktfmt1_Qtag1pktfmt1_qtag1
Pktfmt1_Qtag1pktfmt1_qtag1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3987
S Commandsset pktrw
Page 4132
Pktfmt1_Qtag0pktfmt1_qtag0
Pktfmt1_Qtag0pktfmt1_qtag0
Pktfmt1_Ivntagpktfmt1_ivntag
Pktfmt1_Ivntagpktfmt1_ivntag
Pktfmt1_Vntagpktfmt1_vntag
Pktfmt1_Vntagpktfmt1_vntag
Pktfmt1_Cepktfmt1_ce
Pktfmt1_Cepktfmt1_ce
Pktfmt1_Iethpktfmt1_ieth
Pktfmt1_Iethpktfmt1_ieth
Pktfmt1_Higig2pktfmt1_higig2
Pktfmt1_Higig2pktfmt1_higig2
Pktfmt0_Innerpktfmt0_inner
Pktfmt0_Innerpktfmt0_inner
Pktfmt0_L3pktfmt0_l3
Pktfmt0_L3pktfmt0_l3
Pktfmt0_L3_Typepktfmt0_l3_type
Pktfmt0_L3_Typepktfmt0_l3_type
Pktfmt0_Mpls_Nullpktfmt0_mpls_null
Pktfmt0_Mpls_Nullpktfmt0_mpls_null
Pktfmt0_Snappktfmt0_snap
Pktfmt0_Snappktfmt0_snap
Pktfmt0_Cntagpktfmt0_cntag
Pktfmt0_Cntagpktfmt0_cntag
Pktfmt0_Ttagpktfmt0_ttag
Pktfmt0_Ttagpktfmt0_ttag
Pktfmt0_Cmd_Dgtpktfmt0_cmd_dgt
Pktfmt0_Cmd_Dgtpktfmt0_cmd_dgt
Pktfmt0_Cmd_Sgtpktfmt0_cmd_sgt
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3988
S Commandsset pktrw
Page 4133
Pktfmt0_Cmd_Sgtpktfmt0_cmd_sgt
Pktfmt0_Cdcepktfmt0_cdce
Pktfmt0_Cdcepktfmt0_cdce
Pktfmt0_Trillpktfmt0_trill
Pktfmt0_Trillpktfmt0_trill
Pktfmt0_Qtag2pktfmt0_qtag2
Pktfmt0_Qtag2pktfmt0_qtag2
Pktfmt0_Qtag1pktfmt0_qtag1
Pktfmt0_Qtag1pktfmt0_qtag1
Pktfmt0_Qtag0pktfmt0_qtag0
Pktfmt0_Qtag0pktfmt0_qtag0
Pktfmt0_Ivntagpktfmt0_ivntag
Pktfmt0_Ivntagpktfmt0_ivntag
Pktfmt0_Vntagpktfmt0_vntag
Pktfmt0_Vntagpktfmt0_vntag
Pktfmt0_Cepktfmt0_ce
Pktfmt0_Cepktfmt0_ce
Pktfmt0_Iethpktfmt0_ieth
Pktfmt0_Iethpktfmt0_ieth
Pktfmt0_Higig2pktfmt0_higig2
Pktfmt0_Higig2pktfmt0_higig2
Command Mode
• /exec/elamtah/outsel0
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3989
S Commandsset pktrw
Page 4134
set pktrwset pktrw { spare <spare> | cap_access <cap_access> | bounce <bounce> | dst_vnic_if <dst_vnic_if> | src_vnic_if<src_vnic_if> | pif_block_type <pif_block_type> | epg_out <epg_out> | epg_in <epg_in> | sup_qnum<sup_qnum> | sup_code <sup_code> | ecn_coi <ecn_coi> | ecn_cio <ecn_cio> | ttl_coi <ttl_coi> | ttl_cio<ttl_cio> | qos_map_idx <qos_map_idx> | lat_update <lat_update> | lat_index <lat_index> | dclass <dclass>| sclass <sclass> | ol_fb_metric <ol_fb_metric> | ol_fb_vpath <ol_fb_vpath> | ol_dre <ol_dre> | ol_vpath<ol_vpath> | ol_dp <ol_dp> | ol_sp <ol_sp> | ol_e <ol_e> | ol_dl <ol_dl> | ol_lb <ol_lb> | ol_mark <ol_mark>| ol_udp_sp <ol_udp_sp> | ol_ecn <ol_ecn> | nat_idx <nat_idx> | nat_vld <nat_vld> | dst_addr1 <dst_addr1>| dst_addr0 <dst_addr0> | adj_vld <adj_vld> | encap_l2_idx <encap_l2_idx> | encap_pcid <encap_pcid> |encap_idx <encap_idx> | encap_vld <encap_vld> | my_pcid <my_pcid> | my_tep_idx <my_tep_idx> | fwd_op<fwd_op> | orig_encap_type <orig_encap_type> | pkt_type <pkt_type> | len_type <len_type> | cap_1588<cap_1588> | pktid <pktid> | srcid <srcid> | tstmp <tstmp> | pktfmt1_inner <pktfmt1_inner> | pktfmt1_l3<pktfmt1_l3> | pktfmt1_l3_type <pktfmt1_l3_type> | pktfmt1_mpls_null <pktfmt1_mpls_null> | pktfmt1_snap<pktfmt1_snap> | pktfmt1_cntag <pktfmt1_cntag> | pktfmt1_ttag <pktfmt1_ttag> | pktfmt1_cmd_dgt<pktfmt1_cmd_dgt> | pktfmt1_cmd_sgt <pktfmt1_cmd_sgt> | pktfmt1_cdce <pktfmt1_cdce> | pktfmt1_trill<pktfmt1_trill> | pktfmt1_qtag2 <pktfmt1_qtag2> | pktfmt1_qtag1 <pktfmt1_qtag1> | pktfmt1_qtag0<pktfmt1_qtag0> | pktfmt1_ivntag <pktfmt1_ivntag> | pktfmt1_vntag <pktfmt1_vntag> | pktfmt1_ce<pktfmt1_ce> | pktfmt1_ieth <pktfmt1_ieth> | pktfmt1_higig2 <pktfmt1_higig2> | pktfmt0_inner<pktfmt0_inner> | pktfmt0_l3 <pktfmt0_l3> | pktfmt0_l3_type <pktfmt0_l3_type> | pktfmt0_mpls_null<pktfmt0_mpls_null> | pktfmt0_snap <pktfmt0_snap> | pktfmt0_cntag <pktfmt0_cntag> | pktfmt0_ttag<pktfmt0_ttag> | pktfmt0_cmd_dgt <pktfmt0_cmd_dgt> | pktfmt0_cmd_sgt <pktfmt0_cmd_sgt> | pktfmt0_cdce<pktfmt0_cdce> | pktfmt0_trill <pktfmt0_trill> | pktfmt0_qtag2 <pktfmt0_qtag2> | pktfmt0_qtag1<pktfmt0_qtag1> | pktfmt0_qtag0 <pktfmt0_qtag0> | pktfmt0_ivntag <pktfmt0_ivntag> | pktfmt0_vntag<pktfmt0_vntag> | pktfmt0_ce <pktfmt0_ce> | pktfmt0_ieth <pktfmt0_ieth> | pktfmt0_higig2 <pktfmt0_higig2>} +
Syntax Description
Setup Triggerset
All pktrw fieldspktrw
Sparespare
Sparespare
Cap_Accesscap_access
Cap_Accesscap_access
Bouncebounce
Bouncebounce
Dst_Vnic_Ifdst_vnic_if
Dst_Vnic_Ifdst_vnic_if
Src_Vnic_Ifsrc_vnic_if
Src_Vnic_Ifsrc_vnic_if
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3990
S Commandsset pktrw
Page 4135
Pif_Block_Typepif_block_type
Pif_Block_Typepif_block_type
Epg_Outepg_out
Epg_Outepg_out
Epg_Inepg_in
Epg_Inepg_in
Sup_Qnumsup_qnum
Sup_Qnumsup_qnum
Sup_Codesup_code
Sup_Codesup_code
Ecn_Coiecn_coi
Ecn_Coiecn_coi
Ecn_Cioecn_cio
Ecn_Cioecn_cio
Ttl_Coittl_coi
Ttl_Coittl_coi
Ttl_Ciottl_cio
Ttl_Ciottl_cio
Qos_Map_Idxqos_map_idx
Qos_Map_Idxqos_map_idx
Lat_Updatelat_update
Lat_Updatelat_update
Lat_Indexlat_index
Lat_Indexlat_index
Dclassdclass
Dclassdclass
Sclasssclass
Sclasssclass
Ol_Fb_Metricol_fb_metric
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3991
S Commandsset pktrw
Page 4136
Ol_Fb_Metricol_fb_metric
Ol_Fb_Vpathol_fb_vpath
Ol_Fb_Vpathol_fb_vpath
Ol_Dreol_dre
Ol_Dreol_dre
Ol_Vpathol_vpath
Ol_Vpathol_vpath
Ol_Dpol_dp
Ol_Dpol_dp
Ol_Spol_sp
Ol_Spol_sp
Ol_Eol_e
Ol_Eol_e
Ol_Dlol_dl
Ol_Dlol_dl
Ol_Lbol_lb
Ol_Lbol_lb
Ol_Markol_mark
Ol_Markol_mark
Ol_Udp_Spol_udp_sp
Ol_Udp_Spol_udp_sp
Ol_Ecnol_ecn
Ol_Ecnol_ecn
Nat_Idxnat_idx
Nat_Idxnat_idx
Nat_Vldnat_vld
Nat_Vldnat_vld
Dst_Addr1dst_addr1
Dst_Addr1dst_addr1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3992
S Commandsset pktrw
Page 4137
Dst_Addr0dst_addr0
Dst_Addr0dst_addr0
Adj_Vldadj_vld
Adj_Vldadj_vld
Encap_L2_Idxencap_l2_idx
Encap_L2_Idxencap_l2_idx
Encap_Pcidencap_pcid
Encap_Pcidencap_pcid
Encap_Idxencap_idx
Encap_Idxencap_idx
Encap_Vldencap_vld
Encap_Vldencap_vld
My_Pcidmy_pcid
My_Pcidmy_pcid
My_Tep_Idxmy_tep_idx
My_Tep_Idxmy_tep_idx
Fwd_Opfwd_op
Fwd_Opfwd_op
Orig_Encap_Typeorig_encap_type
Orig_Encap_Typeorig_encap_type
Pkt_Typepkt_type
Pkt_Typepkt_type
Len_Typelen_type
Len_Typelen_type
Cap_1588cap_1588
Cap_1588cap_1588
Pktidpktid
Pktidpktid
Srcidsrcid
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3993
S Commandsset pktrw
Page 4138
Srcidsrcid
Tstmptstmp
Tstmptstmp
Pktfmt1_Innerpktfmt1_inner
Pktfmt1_Innerpktfmt1_inner
Pktfmt1_L3pktfmt1_l3
Pktfmt1_L3pktfmt1_l3
Pktfmt1_L3_Typepktfmt1_l3_type
Pktfmt1_L3_Typepktfmt1_l3_type
Pktfmt1_Mpls_Nullpktfmt1_mpls_null
Pktfmt1_Mpls_Nullpktfmt1_mpls_null
Pktfmt1_Snappktfmt1_snap
Pktfmt1_Snappktfmt1_snap
Pktfmt1_Cntagpktfmt1_cntag
Pktfmt1_Cntagpktfmt1_cntag
Pktfmt1_Ttagpktfmt1_ttag
Pktfmt1_Ttagpktfmt1_ttag
Pktfmt1_Cmd_Dgtpktfmt1_cmd_dgt
Pktfmt1_Cmd_Dgtpktfmt1_cmd_dgt
Pktfmt1_Cmd_Sgtpktfmt1_cmd_sgt
Pktfmt1_Cmd_Sgtpktfmt1_cmd_sgt
Pktfmt1_Cdcepktfmt1_cdce
Pktfmt1_Cdcepktfmt1_cdce
Pktfmt1_Trillpktfmt1_trill
Pktfmt1_Trillpktfmt1_trill
Pktfmt1_Qtag2pktfmt1_qtag2
Pktfmt1_Qtag2pktfmt1_qtag2
Pktfmt1_Qtag1pktfmt1_qtag1
Pktfmt1_Qtag1pktfmt1_qtag1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3994
S Commandsset pktrw
Page 4139
Pktfmt1_Qtag0pktfmt1_qtag0
Pktfmt1_Qtag0pktfmt1_qtag0
Pktfmt1_Ivntagpktfmt1_ivntag
Pktfmt1_Ivntagpktfmt1_ivntag
Pktfmt1_Vntagpktfmt1_vntag
Pktfmt1_Vntagpktfmt1_vntag
Pktfmt1_Cepktfmt1_ce
Pktfmt1_Cepktfmt1_ce
Pktfmt1_Iethpktfmt1_ieth
Pktfmt1_Iethpktfmt1_ieth
Pktfmt1_Higig2pktfmt1_higig2
Pktfmt1_Higig2pktfmt1_higig2
Pktfmt0_Innerpktfmt0_inner
Pktfmt0_Innerpktfmt0_inner
Pktfmt0_L3pktfmt0_l3
Pktfmt0_L3pktfmt0_l3
Pktfmt0_L3_Typepktfmt0_l3_type
Pktfmt0_L3_Typepktfmt0_l3_type
Pktfmt0_Mpls_Nullpktfmt0_mpls_null
Pktfmt0_Mpls_Nullpktfmt0_mpls_null
Pktfmt0_Snappktfmt0_snap
Pktfmt0_Snappktfmt0_snap
Pktfmt0_Cntagpktfmt0_cntag
Pktfmt0_Cntagpktfmt0_cntag
Pktfmt0_Ttagpktfmt0_ttag
Pktfmt0_Ttagpktfmt0_ttag
Pktfmt0_Cmd_Dgtpktfmt0_cmd_dgt
Pktfmt0_Cmd_Dgtpktfmt0_cmd_dgt
Pktfmt0_Cmd_Sgtpktfmt0_cmd_sgt
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3995
S Commandsset pktrw
Page 4140
Pktfmt0_Cmd_Sgtpktfmt0_cmd_sgt
Pktfmt0_Cdcepktfmt0_cdce
Pktfmt0_Cdcepktfmt0_cdce
Pktfmt0_Trillpktfmt0_trill
Pktfmt0_Trillpktfmt0_trill
Pktfmt0_Qtag2pktfmt0_qtag2
Pktfmt0_Qtag2pktfmt0_qtag2
Pktfmt0_Qtag1pktfmt0_qtag1
Pktfmt0_Qtag1pktfmt0_qtag1
Pktfmt0_Qtag0pktfmt0_qtag0
Pktfmt0_Qtag0pktfmt0_qtag0
Pktfmt0_Ivntagpktfmt0_ivntag
Pktfmt0_Ivntagpktfmt0_ivntag
Pktfmt0_Vntagpktfmt0_vntag
Pktfmt0_Vntagpktfmt0_vntag
Pktfmt0_Cepktfmt0_ce
Pktfmt0_Cepktfmt0_ce
Pktfmt0_Iethpktfmt0_ieth
Pktfmt0_Iethpktfmt0_ieth
Pktfmt0_Higig2pktfmt0_higig2
Pktfmt0_Higig2pktfmt0_higig2
Command Mode
• /exec/elamtah/outsel1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3996
S Commandsset pktrw
Page 4141
set pktrwset pktrw { mcast <mcast> | sup_redir <sured> | bcm_proxy <bcm_proxy> | excep_case <excep> | transit<trans> | vpc_df <vpc_df> | src_tep_idx <src_tep> | lat_update <lat_update> | lat_idx <lat_idx> | src_class<sclass> | ol_fb_met <ol_fb_met> | ol_fb_vpath <ol_fb_vpath> | ol_dre <ol_dre> | ol_vpath <ol_vpath> |ol_dp <ol_dp> | ol_sp <ol_sp> | ol_e <ol_e> | ol_dl <ol_dl> | ol_lb <ol_lb> | ol_mark <ol_mark> | ol_udp_sp<ol_udp_sp> | ol_ftag <ol_ftag> | ol_segid <ol_segid> | ol_ttl <ol_ttl> | ol_ecn <ol_ecn> | ol_dscp <ol_dscp>| ol_de <ol_de> | ol_cos <ol_cos> | ol_mac <ol_mac> | ol_encap_idx <ol_encap> | ol_vpc <ol_vpc> | ol_idx<ol_idx> | ttl <ttl> | dscp <dscp> | vlan1 <vlan1> | ecn_coi <ecn_coi> | ecn_cio <ecn_cio> | ttl_coi <ttl_coi>| ttl_cio <ttl_cio> | adj_idx <adj_idx> | vntag_svif <vntag_svif> | de <de> | cos <cos> | vlan0 <vlan0> | adj_vld<adj_vld> | uc_routed <uc_routed> | loopback <lpb> | ecn <ecn> | hg2_vid <hg2_vlan> | hg2_ppd <hg2_ppd>| hg2_tc_sup_copy <hg2_tcscpy> | hg2_tc <hg2_tc> | hg2_lbid <hg2_lbid> | hg2_opc <hg2_opc> | hg2_dstpid<hg2_dpid> | hg2_srcpid <hg2_spid> | hg2_dstmod <hg2_dmod> | hg2_srcmod <hg2_smod> | op_inner<op_inner> | op_qtag <op_qtag> | op_vntag <op_vntag> | op_outer <op_outer> | pkt_type <pkt_type> | drop<drp> | pkt_tstmp <pkt_tstmp> | tstmp <tstmp> | cap_tstmp <cap_tstmp> | len_info <len_info> | len_type<len_type> | pktid <pktid> | srcid <srcid> | pktfmt1 <pktfmt1> | pktfmt0 <pktfmt0> | hg2_cos <hg2_cos> }+
Syntax Description
Setup Triggerset
All packet re-write fieldspktrw
mcastmcast
Mcastmcast
Sup Redirectsup_redir
Sup Redirectsured
Broadcom Proxybcm_proxy
Broadcom Proxybcm_proxy
Excep_caseexcep_case
Excep_caseexcep
Transittransit
Transittrans
VPC_dfvpc_df
VPC_dfvpc_df
Src TEP Indexsrc_tep_idx
Src TEP Indexsrc_tep
Lat Updatelat_update
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3997
S Commandsset pktrw
Page 4142
Lat Updatelat_update
Lat Indexlat_idx
Lat Indexlat_idx
Source Classsrc_class
Source Classsclass
Ol_fb_metricol_fb_met
Ol_fb_metricol_fb_met
Ol_fb_vpathol_fb_vpath
Ol_fb_vpathol_fb_vpath
Ol_dreol_dre
Ol_dreol_dre
Ol_vpathol_vpath
Ol_vpathol_vpath
Ol_dpol_dp
Ol_dpol_dp
Ol_spol_sp
Ol_spol_sp
Ol_eol_e
Ol_eol_e
Ol_dlol_dl
Ol_dlol_dl
Ol_lbol_lb
Ol_lbol_lb
Ol_markol_mark
Ol_markol_mark
Ol_UDP_spol_udp_sp
Ol UDP Source Portol_udp_sp
Ol_ftagol_ftag
Ol_ftagol_ftag
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3998
S Commandsset pktrw
Page 4143
Ol_segidol_segid
Ol_segidol_segid
Ol_TTLol_ttl
Ol_TTLol_ttl
Ol_ecnol_ecn
Ol_ecnol_ecn
Ol_dscpol_dscp
Ol_dscpol_dscp
Ol_deol_de
Ol_deol_de
Ol_cosol_cos
Ol_cosol_cos
Ol_macol_mac
Ol_macol_mac
Ol_encap_idxol_encap_idx
Ol_encap_idxol_encap
Ol_VPCol_vpc
Ol_VPCol_vpc
Ol_idxol_idx
Ol_idxol_idx
TTLttl
TTLttl
DSCPdscp
DSCPdscp
Vlan1vlan1
Vlan1vlan1
ecn_coiecn_coi
ecn_coiecn_coi
ecn_cioecn_cio
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)3999
S Commandsset pktrw
Page 4144
ecn_cioecn_cio
ttl_coittl_coi
ttl_coittl_coi
ttl_ciottl_cio
ttl_ciottl_cio
adj_idxadj_idx
adj_idxadj_idx
vntag_svifvntag_svif
vntag_svifvntag_svif
dede
dede
coscos
coscos
vlan0vlan0
vlan0vlan0
adj_vldadj_vld
adj_vldadj_vld
uc_routeduc_routed
uc_routeduc_routed
loopbackloopback
loopbacklpb
ecnecn
ecnecn
High Gig2 VLAN Taghg2_vid
High Gig2 VLAN Tag Informationhg2_vlan
High Gig2 CoS Informationhg2_cos
High Gig2 CoS Informationhg2_cos
High Gig2 Packet Processing Descriptorhg2_ppd
High Gig2 Packet Processing Descriptorhg2_ppd
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4000
S Commandsset pktrw
Page 4145
High Gig2 Traffic Class SUP Copyhg2_tc_sup_copy
High Gig2 Traffic Class SUP Copyhg2_tcscpy
High Gig2 Packet Traffic Classhg2_tc
High Gig2 Packet Traffic Classhg2_tc
High Gig2 Packet lbidhg2_lbid
High Gig2 Packet lbidhg2_lbid
High Gig2 Packet Typehg2_opc
High Gig2 Packet Typehg2_opc
High Gig2 Destination Port IDhg2_dstpid
High Gig2 Destination Port IDhg2_dpid
High Gig2 Destination Module IDhg2_dstmod
High Gig2 Destination Module IDhg2_dmod
High Gig2 Source Port IDhg2_srcpid
High Gig2 Source Port IDhg2_spid
High Gig2 Souce Module IDhg2_srcmod
High Gig2 Souce Module IDhg2_smod
Op_innerop_inner
Op_innerop_inner
Op_outerop_outer
Op_outerop_outer
Op_qtagop_qtag
Op_qtagop_qtag
Op_vntagop_vntag
Op_vntagop_vntag
Pkt_typepkt_type
Pkt_typepkt_type
Dropdrop
Dropdrp
Packet timestamppkt_tstmp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4001
S Commandsset pktrw
Page 4146
Packet timestamppkt_tstmp
Timestamptstmp
Timestamptstmp
Capture Timestampcap_tstmp
Capture Timestampcap_tstmp
Len_infolen_info
Len_infolen_info
Len_typelen_type
Len_typelen_type
Pkt_idpktid
Pkt_idpktid
Src_idsrcid
Src_idsrcid
Pktfmt1pktfmt1
Pktfmt1pktfmt1
Pktfmt0pktfmt0
Pktfmt0pktfmt0
Command Mode
• /exec/elamns/outsel0
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4002
S Commandsset pktrw
Page 4147
set sb_infoset sb_info { oslice_vec <oslice_vec> | srvc_oslice_vec <srvc_oslice_vec> | is_tcp <is_tcp> | srvc_class<srvc_class> | cpu_oclass <cpu_oclass> | set_v <set_v> | set_idx <set_idx> | set_last <set_last> | bd <bd> |src_is_l3_if <src_is_l3_if> | src_is_vpc_peer <src_is_vpc_peer> | is_my_tep <is_my_tep> | src_sh_group<src_sh_group> | ftag <ftag> | rpf_fail <rpf_fail> | post_route_flood <post_route_flood> | pkt_hash <pkt_hash>| bpdu <bpdu> | met0_v <met0_v> | met0_idx <met0_idx> | met0_last <met0_last> | met1_v <met1_v> |met1_idx <met1_idx> | met1_last <met1_last> | ip_clen <ip_clen> | ip_clen <ip_clen> | sod_cap <sod_cap>| sod_en <sod_en> } +
Syntax Description
Setup Triggerset
All sb_info fieldssb_info
Oslice_Vecoslice_vec
Oslice_Vecoslice_vec
srvc_oslice_vecsrvc_oslice_vec
srvc_oslice_vecsrvc_oslice_vec
is_tcpis_tcp
is_tcpis_tcp
srvc_classsrvc_class
srvc_classsrvc_class
cpu_oclasscpu_oclass
cpu_oclasscpu_oclass
set_vset_v
set_vset_v
set_idxset_idx
set_idxset_idx
set_lastset_last
set_lastset_last
bdbd
bdbd
src_is_l3_ifsrc_is_l3_if
src_is_l3_ifsrc_is_l3_if
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4003
S Commandsset sb_info
Page 4148
src_is_vpc_peersrc_is_vpc_peer
src_is_vpc_peersrc_is_vpc_peer
is_my_tepis_my_tep
is_my_tepis_my_tep
src_sh_groupsrc_sh_group
src_sh_groupsrc_sh_group
ftagftag
ftagftag
rpf_failrpf_fail
rpf_failrpf_fail
post_route_floodpost_route_flood
post_route_floodpost_route_flood
pkt_hashpkt_hash
pkt_hashpkt_hash
bpdubpdu
bpdubpdu
met0_vmet0_v
met0_vmet0_v
met0_idxmet0_idx
met0_idxmet0_idx
met0_lastmet0_last
met0_lastmet0_last
met1_vmet1_v
met1_vmet1_v
met1_idxmet1_idx
met1_idxmet1_idx
met1_lastmet1_last
met1_lastmet1_last
ip_clenip_clen
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4004
S Commandsset sb_info
Page 4149
ip_clenip_clen
sod_capsod_cap
sod_capsod_cap
sod_ensod_en
sod_ensod_en
Command Mode
• /exec/elamtah/outsel0
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4005
S Commandsset sb_info
Page 4150
set sb_infoset sb_info { oslice_vec <oslice_vec> | srvc_oslice_vec <srvc_oslice_vec> | is_tcp <is_tcp> | srvc_class<srvc_class> | cpu_oclass <cpu_oclass> | set_v <set_v> | set_idx <set_idx> | set_last <set_last> | bd <bd> |src_is_l3_if <src_is_l3_if> | src_is_vpc_peer <src_is_vpc_peer> | is_my_tep <is_my_tep> | src_sh_group<src_sh_group> | ftag <ftag> | rpf_fail <rpf_fail> | post_route_flood <post_route_flood> | pkt_hash <pkt_hash>| bpdu <bpdu> | met0_v <met0_v> | met0_idx <met0_idx> | met0_last <met0_last> | met1_v <met1_v> |met1_idx <met1_idx> | met1_last <met1_last> | ip_clen <ip_clen> | ip_clen <ip_clen> | sod_cap <sod_cap>| sod_en <sod_en> } +
Syntax Description
Setup Triggerset
All sb_info fieldssb_info
Oslice_Vecoslice_vec
Oslice_Vecoslice_vec
srvc_oslice_vecsrvc_oslice_vec
srvc_oslice_vecsrvc_oslice_vec
is_tcpis_tcp
is_tcpis_tcp
srvc_classsrvc_class
srvc_classsrvc_class
cpu_oclasscpu_oclass
cpu_oclasscpu_oclass
set_vset_v
set_vset_v
set_idxset_idx
set_idxset_idx
set_lastset_last
set_lastset_last
bdbd
bdbd
src_is_l3_ifsrc_is_l3_if
src_is_l3_ifsrc_is_l3_if
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4006
S Commandsset sb_info
Page 4151
src_is_vpc_peersrc_is_vpc_peer
src_is_vpc_peersrc_is_vpc_peer
is_my_tepis_my_tep
is_my_tepis_my_tep
src_sh_groupsrc_sh_group
src_sh_groupsrc_sh_group
ftagftag
ftagftag
rpf_failrpf_fail
rpf_failrpf_fail
post_route_floodpost_route_flood
post_route_floodpost_route_flood
pkt_hashpkt_hash
pkt_hashpkt_hash
bpdubpdu
bpdubpdu
met0_vmet0_v
met0_vmet0_v
met0_idxmet0_idx
met0_idxmet0_idx
met0_lastmet0_last
met0_lastmet0_last
met1_vmet1_v
met1_vmet1_v
met1_idxmet1_idx
met1_idxmet1_idx
met1_lastmet1_last
met1_lastmet1_last
ip_clenip_clen
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4007
S Commandsset sb_info
Page 4152
ip_clenip_clen
sod_capsod_cap
sod_capsod_cap
sod_ensod_en
sod_ensod_en
Command Mode
• /exec/elamtah/outsel2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4008
S Commandsset sb_info
Page 4153
set sidebandset sideband { cpu_oport <cpu_oport> | span_idx <span_idx> | ovector_idx <ovector_idx> | iclass <iclass> |oclass <oclass> | opcode <opcode> | ecncapable <ecncapable> | nodrop <nodrop> | storefwd <storefwd> |spantransit <spantransit> | rr <rr> | ecnmark <ecnmark> | gbw_tagged <gbw_tagged> | gbw_color <gbw_color>| bnce <bnce> | spanslc <spanslc> | segrate <segrate> | mark <mark> } +
Syntax Description
Setup Triggerset
All sideband fieldssideband
Cpu_Oportcpu_oport
Cpu_Oportcpu_oport
Span_Idxspan_idx
Span_Idxspan_idx
Ovector_Idxovector_idx
Ovector_Idxovector_idx
Iclassiclass
Iclassiclass
Oclassoclass
Oclassoclass
Opcodeopcode
Opcodeopcode
Ecncapableecncapable
Ecncapableecncapable
Nodropnodrop
Nodropnodrop
Storefwdstorefwd
Storefwdstorefwd
Spantransitspantransit
Spantransitspantransit
Rrrr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4009
S Commandsset sideband
Page 4154
Rrrr
Ecnmarkecnmark
Ecnmarkecnmark
Gbw_Taggedgbw_tagged
Gbw_Taggedgbw_tagged
Gbw_Colorgbw_color
Gbw_Colorgbw_color
Bncebnce
Bncebnce
Spanslcspanslc
Spanslcspanslc
Segratesegrate
Segratesegrate
Markmark
Markmark
Command Mode
• /exec/elamtah/outsel2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4010
S Commandsset sideband
Page 4155
set sidebandset sideband { cpu_oport <cpu_oport> | span_idx <span_idx> | ovector_idx <ovector_idx> | iclass <iclass> |oclass <oclass> | opcode <opcode> | ecncapable <ecncapable> | nodrop <nodrop> | storefwd <storefwd> |spantransit <spantransit> | rr <rr> | ecnmark <ecnmark> | gbw_tagged <gbw_tagged> | gbw_color <gbw_color>| bnce <bnce> | spanslc <spanslc> | segrate <segrate> | mark <mark> } +
Syntax Description
Setup Triggerset
All sideband fieldssideband
Cpu_Oportcpu_oport
Cpu_Oportcpu_oport
Span_Idxspan_idx
Span_Idxspan_idx
Ovector_Idxovector_idx
Ovector_Idxovector_idx
Iclassiclass
Iclassiclass
Oclassoclass
Oclassoclass
Opcodeopcode
Opcodeopcode
Ecncapableecncapable
Ecncapableecncapable
Nodropnodrop
Nodropnodrop
Storefwdstorefwd
Storefwdstorefwd
Spantransitspantransit
Spantransitspantransit
Rrrr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4011
S Commandsset sideband
Page 4156
Rrrr
Ecnmarkecnmark
Ecnmarkecnmark
Gbw_Taggedgbw_tagged
Gbw_Taggedgbw_tagged
Gbw_Colorgbw_color
Gbw_Colorgbw_color
Bncebnce
Bncebnce
Spanslcspanslc
Spanslcspanslc
Segratesegrate
Segratesegrate
Markmark
Markmark
Command Mode
• /exec/elamtah/outsel0
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4012
S Commandsset sideband
Page 4157
set sidebandset sideband { cpu_oport <cpu_oport> | span_idx <span_idx> | ovector_idx <ovector_idx> | iclass <iclass> |oclass <oclass> | opcode <opcode> | ecncapable <ecncapable> | nodrop <nodrop> | storefwd <storefwd> |spantransit <spantransit> | rr <rr> | ecnmark <ecnmark> | gbw_tagged <gbw_tagged> | gbw_color <gbw_color>| bnce <bnce> | spanslc <spanslc> | segrate <segrate> | mark <mark> } +
Syntax Description
Setup Triggerset
All sideband fieldssideband
Cpu_Oportcpu_oport
Cpu_Oportcpu_oport
Span_Idxspan_idx
Span_Idxspan_idx
Ovector_Idxovector_idx
Ovector_Idxovector_idx
Iclassiclass
Iclassiclass
Oclassoclass
Oclassoclass
Opcodeopcode
Opcodeopcode
Ecncapableecncapable
Ecncapableecncapable
Nodropnodrop
Nodropnodrop
Storefwdstorefwd
Storefwdstorefwd
Spantransitspantransit
Spantransitspantransit
Rrrr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4013
S Commandsset sideband
Page 4158
Rrrr
Ecnmarkecnmark
Ecnmarkecnmark
Gbw_Taggedgbw_tagged
Gbw_Taggedgbw_tagged
Gbw_Colorgbw_color
Gbw_Colorgbw_color
Bncebnce
Bncebnce
Spanslcspanslc
Spanslcspanslc
Segratesegrate
Segratesegrate
Markmark
Markmark
Command Mode
• /exec/elamtah/outsel1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4014
S Commandsset sideband
Page 4159
set sidebandset sideband { span_vec <span_vec> | bounce <bnc> | mclast <mclast> | mcastcurptr <mccurptr> | mcastcurptr_v<mccurptr_v> | srcport <sport> | vlan <vlan> | segwgt <segwgt> | segid <segid> | seglocal <seglcl> | gbw_color<gbw_color> | gbw_tag <gbw_tagg> | fwddrp <fwddrp> | l2fld <l2fld> | nodrp <nodrp> | ovrlyidx <ovrlyidx>| ecncap <ecncap> | cpu <cpu> | store_fwd <stfwd> | mcast <mcast> | oclass <ocls> | iclass <icls> | odest_v<odest_v> | odest <odest> | ovec <ovec> | span_trans <span_trans> | lbtype <lbtype> | lbena <lbena> | tdmid<tdmid> | pktid <pktid> | srcid <srcid> | eoferror <eoferr> | eofbytes <eofby> | eof <eof> | sof <sof> } +
Syntax Description
Setup Triggerset
All sideband fieldssideband
SPAN vectorspan_vec
SPAN vectorspan_vec
Bouncebounce
Bouncebnc
Mclastmclast
Mclastmclast
Mcast cur ptrmcastcurptr
Mcast cur ptrmccurptr
Mcast cur ptr vmcastcurptr_v
Mcast cur ptr vmccurptr_v
Source Portsrcport
Source Portsport
Vlanvlan
Vlanvlan
Segwgtsegwgt
Segwgtsegwgt
Segidsegid
Segidsegid
Seglocalseglocal
Seglocalseglcl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4015
S Commandsset sideband
Page 4160
GBW colorgbw_color
GBW colorgbw_color
GBW taggedgbw_tag
GBW taggedgbw_tagg
Forward dropfwddrp
Forward dropfwddrp
L2 Floodl2fld
L2 Floodl2fld
No dropnodrp
No dropnodrp
Overlay indexovrlyidx
Overlay indexovrlyidx
ECN Capableecncap
ECN Capableecncap
CPUcpu
CPUcpu
Store_fwdstore_fwd
Store_fwdstfwd
Multicastmcast
Multicastmcast
Output classoclass
Output classocls
Input classiclass
Input classicls
Odest_vodest_v
Odest_vodest_v
Odestodest
Odestodest
Ovectorovec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4016
S Commandsset sideband
Page 4161
Ovectorovec
SPAN transitspan_trans
SPAN transitspan_trans
Lbtypelbtype
Lbtypelbtype
Lbenablelbena
Lbenablelbena
Tdmidtdmid
Tdmidtdmid
Pkt_idpktid
Pkt_idpktid
Src_idsrcid
Src_idsrcid
EOF erroreoferror
EOF erroeoferr
EOF byteseofbytes
EOF byteseofby
EOFeof
EOFeof
SOFsof
SOFsof
Command Mode
• /exec/elamns/outsel5
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4017
S Commandsset sideband
Page 4162
set statsset stats { vld0 <vld0> | atomic0 <atomic0> | mode0 <mode0> | index0 <index0> | vld1 <vld1> | atomic1<atomic1> | mode1 <mode1> | index1 <index1> | vld2 <vld2> | atomic2 <atomic2> | mode2 <mode2> | index2<index2> | vld3 <vld3> | atomic3 <atomic3> | mode3 <mode3> | index3 <index3> | vld4 <vld4> | atomic4<atomic4> | mode4 <mode4> | index4 <index4> | vld5 <vld5> | atomic5 <atomic5> | mode5 <mode5> | index5<index5> | vld6 <vld6> | atomic6 <atomic6> | mode6 <mode6> | index6 <index6> | vld7 <vld7> | atomic7<atomic7> | mode7 <mode7> | index7 <index7> } +
Syntax Description
Setup Triggerset
All stats fieldsstats
Vld0vld0
Vld0vld0
Atomic0atomic0
Atomic0atomic0
Mode0mode0
Mode0mode0
Index0index0
Index0index0
Vld1vld1
Vld1vld1
Atomic1atomic1
Atomic1atomic1
Mode1mode1
Mode1mode1
Index1index1
Index1index1
Vld2vld2
Vld2vld2
Atomic2atomic2
Atomic2atomic2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4018
S Commandsset stats
Page 4163
Mode2mode2
Mode2mode2
Index2index2
Index2index2
Vld3vld3
Vld3vld3
Atomic3atomic3
Atomic3atomic3
Mode3mode3
Mode3mode3
Index3index3
Index3index3
Vld4vld4
Vld4vld4
Atomic4atomic4
Atomic4atomic4
Mode4mode4
Mode4mode4
Index4index4
Index4index4
Vld5vld5
Vld5vld5
Atomic5atomic5
Atomic5atomic5
Mode5mode5
Mode5mode5
Index5index5
Index5index5
Vld6vld6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4019
S Commandsset stats
Page 4164
Vld6vld6
Atomic6atomic6
Atomic6atomic6
Mode6mode6
Mode6mode6
Index6index6
Index6index6
Vld7vld7
Vld7vld7
Atomic7atomic7
Atomic7atomic7
Mode7mode7
Mode7mode7
Index7index7
Index7index7
Command Mode
• /exec/elamtah/outsel2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4020
S Commandsset stats
Page 4165
set tag{ { set tag <value> } | { no set tag [ <value> ] } }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
Tag value for destination routing protocoltag
Tag valuevalue
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4021
S Commandsset tag
Page 4166
set weight{ set weight <count> | no set weight [ <count> ] }
Syntax Description
Negate a command or set its defaultsno
Set values in destination routing protocolset
BGP weight for routing tableweight
Weight valuecount
Command Mode
• /exec/configure/route-map
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4022
S Commandsset weight
Page 4167
setupsetup
Syntax Description
Run the basic SETUP command facilitysetup
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4023
S Commandssetup
Page 4168
sflowsflow { [ sampling-rate <rate> ] | [ max-sampled-size <pkt-size> ] | [ counter-poll-interval <interval> ] | [max-datagram-size <dgram-size> ] | [ collector-ip <dst-ip> vrf { <vrf-name> | <vrf-known-name> } [ source<src-ip> ] ] | [ collector-port <dst-port> ] | [ agent-ip <agent-ip> ] }
Syntax Description
change sFlow global settingssflow
(Optional) sFlow Sampling Ratesampling-rate
(Optional)rate
(Optional) sFlow Sampled Sizemax-sampled-size
(Optional) sFlow Sampled Sizepkt-size
(Optional) sFlow Counter Poll Intervalcounter-poll-interval
(Optional) sFlow Counter Poll Intervalinterval
(Optional) sFlow Datagram Sizemax-datagram-size
(Optional) sFlow Datagram Sizedgram-size
(Optional) sFlow Collector IP addresscollector-ip
(Optional) sFlow Collector IP addressdst-ip
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Source IP address to send to sFlow Collectorsource
(Optional) Source IP address to send to sFlow Collectorsrc-ip
(Optional) sFlow Collector UDP portcollector-port
(Optional) sFlow Collector UDP portdst-port
(Optional) sFlow Agent IP addressagent-ip
(Optional) sFlow Agent IP addressagent-ip
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4024
S Commandssflow
Page 4169
sflow[no] sflow { sampling-rate | max-sampled-size | counter-poll-interval | max-datagram-size | collector-ip |collector-port | agent-ip }
Syntax Description
Negate a command or set its defaultsno
change sFlow global settingssflow
sFlow Sampling Ratesampling-rate
sFlow Sampled Sizemax-sampled-size
sFlow Counter Poll Intervalcounter-poll-interval
sFlow Datagram Sizemax-datagram-size
sFlow Collector IP addresscollector-ip
sFlow Collector UDP portcollector-port
sFlow Agent IP addressagent-ip
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4025
S Commandssflow
Page 4170
sflow data-source interfacesflow data-source interface { <ifnum> | <pcifnum> }
Syntax Description
change sFlow global settingssflow
sFlow Data Sourcedata-source
sFlow Data Source Interfaceinterface
sFlow Data Source Interfaceifnum
sFlow Data Source Interfacepcifnum
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4026
S Commandssflow data-source interface
Page 4171
sflow data-source interface[no] sflow data-source interface { <ifnum> | <pcifnum> }
Syntax Description
Negate a command or set its defaultsno
change sFlow global settingssflow
sFlow Data Sourcedata-source
sFlow Data Source Interfaceinterface
sFlow Data Source Interfaceifnum
sFlow Data Source Interfacepcifnum
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4027
S Commandssflow data-source interface
Page 4172
sflow extended switch[no] sflow extended switch
Syntax Description
(Optional) Negate a command or set its defaultsno
change sFlow global settingssflow
sFlow extended flow recordsextended
sFlow extended switch flowswitch
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4028
S Commandssflow extended switch
Page 4173
shape[no] shape { { { [ average ] { <avg-rate> [ bps | kbps | mbps | gbps ] | percent <percentage> } } | { min {<min-rate> [ bps2 | kbps2 | mbps2 | gbps2 | pps2 ] | percent2 <percentage2> } max { <max-rate> [ bps3 |kbps3 | mbps3 | gbps3 | pps3 ] | percent3 <percentage3> } } } | { { kbps4 | pps4 } { <max-rate4> [ min2<min-rate4> ] } } }
Syntax Description
(Optional) Negate a command or set its defaultsno
shapeshape
(Optional) Configure average shape rateaverage
Configure minimum shape ratemin
Configure maximum shape ratemax
(Optional) Bits per secondbps
(Optional) Kilo bits per secondkbps
(Optional) Mega bits per secondmbps
(Optional) Giga bits per secondgbps
(Optional) Bits per secondbps2
(Optional) Kilo Bits per secondkbps2
(Optional) Mega Bits per secondmbps2
(Optional) Giga Bits per secondgbps2
(Optional) Packets per secondpps2
(Optional) Bits per secondbps3
(Optional) Kilo Bits per secondkbps3
(Optional) Mega Bits per secondmbps3
(Optional) Giga Bits per secondgbps3
(Optional) Packets per secondpps3
Specify rate as percentage of interface data-ratepercent
Specify rate as percentage of interface data-ratepercent2
Specify rate as percentage of interface data-ratepercent3
Percentagepercentage
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4029
S Commandsshape
Page 4174
Percentagepercentage2
Percentagepercentage3
Kilo Bits per secondkbps4
Packets per secondpps4
(Optional) Min guaranteed bandwidthmin2
Command Mode
• /exec/configure/policy-map/type/queuing/class
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4030
S Commandsshape
Page 4175
shared-secret[no] shared-secret { 10 <clear> | 7 <encrypted> | <secret> } [ user <user> password { 0 <clear> | 7 <encrypted>| <password> } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Shared-secretshared-secret
Enter shared-secret in clear textsecret
password in clear text10
Password in clear textclear
Password that follows should be in encrypted text7
Encrypted passwordencrypted
(Optional) User Nameuser
(Optional) Enter user nameuser
(Optional) Passwordpassword
(Optional) Enter password in clear textpassword
(Optional) Password that follows should be in clear text0
(Optional) Password in clear textclear
(Optional) Password that follows should be in encrypted text7
(Optional) Encrypted passwordencrypted
Command Mode
• /exec/configure/fabric-db/server-radius
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4031
S Commandsshared-secret
Page 4176
shut[no] shut
Syntax Description
(Optional) Negate a command or set its defaultsno
Shut a monitor sessionshut
Command Mode
• /exec/configure/monitor-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4032
S Commandsshut
Page 4177
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
shutdown
Command Mode
• /exec/configure/smartc /exec/configure/smartc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4033
S Commandsshutdown
Page 4178
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Shutdown this instance of RIPshutdown
Command Mode
• /exec/configure/router-rip /exec/configure/router-rip/router-rip-vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4034
S Commandsshutdown
Page 4179
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Change the admin status of the bundleshutdown
Command Mode
• /exec/configure/anycast
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4035
S Commandsshutdown
Page 4180
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
shutdown
Command Mode
• /exec/configure/catena /exec/configure/catena
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4036
S Commandsshutdown
Page 4181
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Shutdown tunnel interface(s)shutdown
Command Mode
• /exec/configure/if-any-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4037
S Commandsshutdown
Page 4182
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
OpenFlow switch shutdownshutdown
Command Mode
• /exec/configure/openflow/switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4038
S Commandsshutdown
Page 4183
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
OpenFlow switch shutdownshutdown
Command Mode
• /exec/configure/openflow/switch/sub-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4039
S Commandsshutdown
Page 4184
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Shutdown this IS-IS processshutdown
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4040
S Commandsshutdown
Page 4185
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
shutdown the OSPF protocol instanceshutdown
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4041
S Commandsshutdown
Page 4186
shutdown[no] shutdown
Syntax Description
(Optional) Negate the commandno
Enable Transient Capture Buffershutdown
Command Mode
• /exec/configure/pkt-drop
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4042
S Commandsshutdown
Page 4187
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Shutdown this instance of EIGRPshutdown
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4043
S Commandsshutdown
Page 4188
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable or disable a VRshutdown
Command Mode
• /exec/configure/if-eth-any/vrrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4044
S Commandsshutdown
Page 4189
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/disable an interfaceshutdown
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4045
S Commandsshutdown
Page 4190
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Shutdown Segment Routingshutdown
Command Mode
• /exec/configure/config-sr-mpls
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4046
S Commandsshutdown
Page 4191
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Shutdown VLAN switchingshutdown
Command Mode
• /exec/configure/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4047
S Commandsshutdown
Page 4192
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/disable an interfaceshutdown
Command Mode
• /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4048
S Commandsshutdown
Page 4193
shutdown[no] shutdown [ force ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/disable an interfaceshutdown
(Optional) Enable/disable an interfaceforce
Command Mode
• /exec/configure/if-ethernet /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all/exec/configure/if-eth-base /exec/configure/if-port-channel /exec/configure/if-eth-port-channel/exec/configure/if-ethernet-all /exec/configure/if-ethernet-p2p /exec/configure/if-remote-ethernet-sub/exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p /exec/configure/if-port-channel-sub/exec/configure/if-port-channel-range
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4049
S Commandsshutdown
Page 4194
shutdown[no] shutdown [ force ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/disable an interfaceshutdown
(Optional) Enable/disable an interfaceforce
Command Mode
• /exec/configure/if-ethernet /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all/exec/configure/if-eth-base /exec/configure/if-port-channel /exec/configure/if-eth-port-channel/exec/configure/if-ethernet-all /exec/configure/if-ethernet-p2p /exec/configure/if-remote-ethernet-sub/exec/configure/if-ether-sub /exec/configure/if-ether-sub-p2p /exec/configure/if-port-channel-sub
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4050
S Commandsshutdown
Page 4195
shutdown[no] shutdown [ force ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/disable an interfaceshutdown
(Optional) Enable/disable an interfaceforce
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4051
S Commandsshutdown
Page 4196
shutdown[no] shutdown [ force ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/disable an interfaceshutdown
(Optional) Enable/disable an interfaceforce
Command Mode
• /exec/configure/if-loopback
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4052
S Commandsshutdown
Page 4197
shutdown[no] shutdown [ force ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/disable an interfaceshutdown
(Optional) Enable/disable an interfaceforce
Command Mode
• /exec/configure/if-cpp /exec/configure/if-fv /exec/configure/if-fa /exec/configure/if-svc/exec/configure/if-fc-tunnel /exec/configure/if-sme /exec/configure/if-ioa /exec/configure/if-overlay/exec/configure/if-te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4053
S Commandsshutdown
Page 4198
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/disable an interfaceshutdown
Command Mode
• /exec/configure/if-gig-ether /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext/exec/configure/if-vsan /exec/configure/if-iscsi /exec/configure/if-fcip /exec/configure/if-sme/exec/configure/if-ioa /exec/configure/if-san-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4054
S Commandsshutdown
Page 4199
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/disable an interfaceshutdown
Command Mode
• /exec/configure/if-vfc /exec/configure/if-vfc-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4055
S Commandsshutdown
Page 4200
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Shutdown the OSPF protocol instanceshutdown
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4056
S Commandsshutdown
Page 4201
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Disable MPLS forwarding for IPshutdown
Command Mode
• /exec/configure/ldp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4057
S Commandsshutdown
Page 4202
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
shutdown
Command Mode
• /exec/configure/itd /exec/configure/itd-inout
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4058
S Commandsshutdown
Page 4203
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Shut down VRRPv3shutdown
Command Mode
• /exec/configure/vrrpv3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4059
S Commandsshutdown
Page 4204
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Shut down the groupshutdown
Command Mode
• /exec/configure/if-eth-any/vrrpv3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4060
S Commandsshutdown
Page 4205
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Shut down the pathwayshutdown
Command Mode
• /exec/configure/if-eth-any/vrrs
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4061
S Commandsshutdown
Page 4206
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Shutdown current VRFshutdown
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4062
S Commandsshutdown
Page 4207
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Administratively shutdown BGP protocolshutdown
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4063
S Commandsshutdown
Page 4208
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Administratively shutdown this BMP servershutdown
Command Mode
• /exec/configure/router-bgp/router-bgp-bmp-server
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4064
S Commandsshutdown
Page 4209
shutdown[ no | default ] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Administratively shutdown this neighborshutdown
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4065
S Commandsshutdown
Page 4210
shutdownshutdown | no shutdown
Syntax Description
Negate a command or set its defaultsno
suspend vPC locallyshutdown
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4066
S Commandsshutdown
Page 4211
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Shutdown PLB serviceshutdown
Command Mode
• /exec/configure/plb /exec/configure/plb-inout
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4067
S Commandsshutdown
Page 4212
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Shutdown MPLS Traffic Engineeringshutdown
Command Mode
• /exec/configure/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4068
S Commandsshutdown
Page 4213
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Disable current explicit-pathshutdown
Command Mode
• /exec/configure/te/expl-path
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4069
S Commandsshutdown
Page 4214
shutdown[no] shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Shutdown the CBTS member LSPshutdown
Command Mode
• /exec/configure/tunnel-te/cbts-member
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4070
S Commandsshutdown
Page 4215
shutdown force[no] shutdown force
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/disable an interfaceshutdown
Enable/disable an interfaceforce
Command Mode
• /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4071
S Commandsshutdown force
Page 4216
shutdown lanshutdown lan
Syntax Description
Enable/disable an interfaceshutdown
Shut all LAN VLANs on interfacelan
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4072
S Commandsshutdown lan
Page 4217
shutdown lan[no] shutdown lan
Syntax Description
Negate a command or set its defaultsno
Enable/disable an interfaceshutdown
Shut all LAN VLANs on interfacelan
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4073
S Commandsshutdown lan
Page 4218
signalling advertise explicit-null[no] signalling advertise explicit-null | signalling advertise explicit-null [ <acl> ]
Syntax Description
Negate a command or set its defaultsno
Traffic Engineering Signalling Parameterssignalling
Signalling advertisement parametersadvertise
Advertise explicit-null label in signalling messagesexplicit-null
(Optional) Access listacl
Command Mode
• /exec/configure/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4074
S Commandssignalling advertise explicit-null
Page 4219
signalling hello graceful-restart[no] signalling hello graceful-restart
Syntax Description
Configure RSVP Signalling informationsignalling
RSVP Hello configuration commandshello
RSVP Graceful restart commandsgraceful-restart
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4075
S Commandssignalling hello graceful-restart
Page 4220
signalling hello graceful-restart refresh interval[no] signalling hello graceful-restart refresh interval <value>
Syntax Description
Configure RSVP Signalling informationsignalling
RSVP Hello configuration commandshello
RSVP Graceful restart commandsgraceful-restart
Configure RSVP Hello refresh behavior for Graceful Restartrefresh
Time between sending Hello Requests for Graceful Restartinterval
Hello interval in msecvalue
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4076
S Commandssignalling hello graceful-restart refresh interval
Page 4221
signalling hello graceful-restart refresh misses[no] signalling hello graceful-restart refresh misses <value>
Syntax Description
Configure RSVP Signalling informationsignalling
RSVP Hello configuration commandshello
RSVP Graceful restart commandsgraceful-restart
Configure RSVP Hello refresh behavior for Graceful Restartrefresh
Number of Hello misses for Graceful Restartmisses
Number of missed Hello Acks which triggers neighbor downvalue
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4077
S Commandssignalling hello graceful-restart refresh misses
Page 4222
signalling hello graceful-restart send recovery-time[no] signalling hello graceful-restart send recovery-time <value>
Syntax Description
Configure RSVP Signalling informationsignalling
RSVP Hello configuration commandshello
RSVP Graceful restart commandsgraceful-restart
Configure the restart-time in outgoing Hello msgssend
Configure the recovery-time in outgoing GR Hello msgsrecovery-time
recovery-time in msecvalue
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4078
S Commandssignalling hello graceful-restart send recovery-time
Page 4223
signalling hello graceful-restart send restart-time[no] signalling hello graceful-restart send restart-time <value>
Syntax Description
Configure RSVP Signalling informationsignalling
RSVP Hello configuration commandshello
RSVP Graceful restart commandsgraceful-restart
Configure the restart-time in outgoing Hello msgssend
Configure the restart-time in outgoing GR Hello msgsrestart-time
restart-time in msecvalue
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4079
S Commandssignalling hello graceful-restart send restart-time
Page 4224
signalling hello reroute[no] signalling hello reroute
Syntax Description
Configure RSVP Signalling informationsignalling
RSVP Hello configuration commandshello
RSVP Reroute commandsreroute
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4080
S Commandssignalling hello reroute
Page 4225
signalling initial-retransmit-delay[no] signalling initial-retransmit-delay <msec>
Syntax Description
Configure RSVP Signalling informationsignalling
RSVP Initial retransmit delayinitial-retransmit-delay
Initial retransmit delay in millisecmsec
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4081
S Commandssignalling initial-retransmit-delay
Page 4226
signalling patherr state-removal[no] signalling patherr state-removal
Syntax Description
Configure RSVP Signalling informationsignalling
Configure Path-Error processingpatherr
Setup automatic removal of path-statestate-removal
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4082
S Commandssignalling patherr state-removal
Page 4227
signalling rate-limit[no] signalling rate-limit { [ interval <msec> ] [ limit <messages> ] } | { [ limit <messages> ] [ interval <msec>] }
Syntax Description
Configure RSVP Signalling informationsignalling
Configure rate-limitingrate-limit
(Optional) Configure scheduling intervalinterval
(Optional) Interval in millisecmsec
(Optional) Configure message limit per scheduling intervallimit
(Optional) Message limit valuemessages
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4083
S Commandssignalling rate-limit
Page 4228
signalling refresh interval[no] signalling refresh interval <seconds>
Syntax Description
Configure RSVP Signalling informationsignalling
Configure RSVP signaling refresh parametersrefresh
Set signaling refresh intervalinterval
Signaling refresh interval in secondsseconds
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4084
S Commandssignalling refresh interval
Page 4229
signalling refresh misses[no] signalling refresh misses <value>
Syntax Description
Configure RSVP Signalling informationsignalling
Configure RSVP signaling refresh parametersrefresh
Set refresh misses tolerated before expiring a statemisses
Refresh miss valuevalue
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4085
S Commandssignalling refresh misses
Page 4230
signalling refresh reduction[no] signalling refresh reduction
Syntax Description
Configure RSVP Signalling informationsignalling
Configure RSVP signaling refresh parametersrefresh
Enable, disable or set refresh reduction parametersreduction
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4086
S Commandssignalling refresh reduction
Page 4231
signalling refresh reduction ack-delay[no] signalling refresh reduction ack-delay <msec>
Syntax Description
Configure RSVP Signalling informationsignalling
Configure RSVP signaling refresh parametersrefresh
Enable, disable or set refresh reduction parametersreduction
Set delay for sending ACK messagesack-delay
ACK delay value in millisecmsec
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4087
S Commandssignalling refresh reduction ack-delay
Page 4232
signalling refresh reduction bundle-max-size[no] signalling refresh reduction bundle-max-size <value>
Syntax Description
Configure RSVP Signalling informationsignalling
Configure RSVP signaling refresh parametersrefresh
Enable, disable or set refresh reduction parametersreduction
Set bundle-maximum-sizebundle-max-size
Bundle size in bytes, use zero to disable bundlingvalue
Command Mode
• /exec/configure/ip-rsvp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4088
S Commandssignalling refresh reduction bundle-max-size
Page 4233
signing level{ [ no ] signing level { none | cisco | unsigned } | no signing level }
Syntax Description
(Optional) Negate a command or set its defaultsno
Virtual service package signing settingssigning
Package signing level allowed for virtual service installationlevel
Most restrictive, don't allow package installationnone
Allow only Cisco signed packagescisco
Least restrictive, allow unsigned and all signing methodsunsigned
Command Mode
• /exec/configure/virt-serv-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4089
S Commandssigning level
Page 4234
site-id{ site-id <s0> | no site-id }
Syntax Description
Negate a command or set its defaultsno
site id of the network where switch is deployedsite-id
Provide site ids0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4090
S Commandssite-id
Page 4235
site-of-origin{ site-of-origin { <ext-comm-soo-aa2nn4> | <ext-comm-soo-aa4nn2> } } | { no site-of-origin [ {<ext-comm-soo-aa2nn4> | <ext-comm-soo-aa4nn2> } ] }
Syntax Description
Negate a command or set its defaultsno
Site of Originsite-of-origin
Extcommunity numberext-comm-soo-aa2nn4
Extcommunity numberext-comm-soo-aa4nn2
Command Mode
• /exec/configure/if-igp /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4091
S Commandssite-of-origin
Page 4236
slave ipv4[no] slave ipv4 <ip>
Syntax Description
(Optional) Negate a command or set its defaultsno
slaveslave
ipv4ipv4
IPv4 address (A.B.C.D) of slaveip
Command Mode
• /exec/configure/ptp-ucast-master
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4092
S Commandsslave ipv4
Page 4237
sleepsleep <i0>
Syntax Description
Sleep for the specified number of secondssleep
Enter the number of seconds to sleepi0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4093
S Commandssleep
Page 4238
sleep instance[no] sleep instance <inst> [ <i0> ] | sleep instance <inst> <i0>
Syntax Description
Negate a command or set its defaultsno
Sleep for the specified number of secondssleep
Label with an instance numberinstance
Instance numberinst
(Optional) Enter the number of seconds to sleepi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4094
S Commandssleep instance
Page 4239
slotslot <module> { quoted <quoted-cmd> | <cmd> }
Syntax Description
run commands on specific linecard (or set slot for commands that takeoptional slot number)
slot
the slot number (aka module number)module
enter the command with quotes -> pipe redirection and semi-colon arelocal
quoted
the command(s) to run on lc separated by <space> <semi-colon> <space>quoted-cmd
the command(s) to run on lc separated by <space> <semi-colon> <space>cmd
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4095
S Commandsslot
Page 4240
slotslot <module>
Syntax Description
Configure a slotslot
the slot number (aka module number)module
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4096
S Commandsslot
Page 4241
smart-channel{ smart-channel <service-name> } | { no smart-channel <service-name> }
Syntax Description
Negate a command or set its defaultsno
L2 servicesmart-channel
L2 service-nameservice-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4097
S Commandssmart-channel
Page 4242
smart-channel port-group{ smart-channel port-group <svc-name> } | { no smart-channel port-group <svc-name> }
Syntax Description
Negate a command or set its defaultsno
servicesmart-channel
port groupport-group
service-namesvc-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4098
S Commandssmart-channel port-group
Page 4243
smtp-host smtp-port reply-to from{ smtp-host { <ipv4> | <ipv6> | <host> } [ smtp-port <port> ] | smtp-port <port> | reply-to <reply> | from<from> |
Syntax Description
}
SMTP server hostsmtp-host
IPV4 addressipv4
DNS namehost
(Optional) SMTP server portsmtp-port
(Optional) Port for SMTP serverport
Reply to email addressreply-to
Provide reply-to email addressreply
From email addressfrom
Provide from email addressfrom
Command Mode
• /exec/configure/email
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4099
S Commandssmtp-host smtp-port reply-to from
Page 4244
snapshot createsnapshot create <snapshot-name> <snapshot-description>
Syntax Description
Create/Delete a snapshotsnapshot
Create a snapshot of running state of selected featurescreate
Name of a snapshotsnapshot-name
Description of a snapshotsnapshot-description
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4100
S Commandssnapshot create
Page 4245
snapshot deletesnapshot delete <snapshot-name>
Syntax Description
Create/Delete a snapshotsnapshot
Delete a single snapshot or all snapshotsdelete
Name of a snapshotsnapshot-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4101
S Commandssnapshot delete
Page 4246
snapshot delete ALLsnapshot delete ALL
Syntax Description
Create/Delete a snapshotsnapshot
Delete a single snapshot or all snapshotsdelete
Delete all snapshots present on the switchALL
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4102
S Commandssnapshot delete ALL
Page 4247
snapshot section addsnapshot section add <name> <command> <row-id> <key1> [ <key2> ]
Syntax Description
Create/Delete a snapshotsnapshot
Add/Delete a snapshot sectionsection
Add a snapshot sectionadd
Name of a sectionname
show' command to generate XML outputcommand
tag of each row entry of the 'show' XML outputrow-id
first key to distinguish among row entries withkey1
(Optional) second key to distinguish among row entries withkey2
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4103
S Commandssnapshot section add
Page 4248
snapshot section deletesnapshot section delete <name>
Syntax Description
Create/Delete a snapshotsnapshot
Add/Delete a snapshot sectionsection
Delete a snapshot sectiondelete
Name of a sectionname
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4104
S Commandssnapshot section delete
Page 4249
snmp-server aaa-user cache-timeout[no] snmp-server aaa-user cache-timeout <timeout>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
set duration for which aaa-cached snmp user existsaaa-user
timeout for AAA cachecache-timeout
timeout for which aaa-cached user exists(in secs)timeout
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4105
S Commandssnmp-server aaa-user cache-timeout
Page 4250
snmp-server community{ no snmp-server community <community_name> { use-ipv4acl [ <ipv4_acl_name> ] use-ipv6acl [<ipv6_acl_name> ] | use-ipv4acl [ <ipv4_acl_name> ] | use-ipv6acl [ <ipv6_acl_name> ] } | snmp-servercommunity <community_name> { use-ipv4acl <ipv4_acl_name> use-ipv6acl <ipv6_acl_name> | use-ipv4acl<ipv4_acl_name> | use-ipv6acl <ipv6_acl_name> } }
Syntax Description
Negate a command or set its defaultsno
Configure snmp serversnmp-server
set community string and access privscommunity
SNMP community stringcommunity_name
Specify IPv4 ACL, the ACL name specified after must be IPv4 ACL.use-ipv4acl
(Optional) IPv4 ACL name to filter snmp requestsipv4_acl_name
Specify IPv6 ACL, the ACL name specified after must be IPv6 ACL.use-ipv6acl
(Optional) IPv6 ACL name to filter snmp requestsipv6_acl_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4106
S Commandssnmp-server community
Page 4251
snmp-server community[no] snmp-server community <s0> [ { group <s1> | ro | rw } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
set community string and access privscommunity
SNMP community strings0
(Optional) Group to which the community belongsgroup
(Optional) Group to which the community belongss1
(Optional) Read-only access with this community stringro
(Optional) Read-write access with this community stringrw
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4107
S Commandssnmp-server community
Page 4252
snmp-server community use-acl[no] snmp-server community <community_name> use-acl <acl_name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
set community string and access privscommunity
SNMP community stringcommunity_name
acl name to filter snmp requestsuse-acl
acl name to filter snmp requestsacl_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4108
S Commandssnmp-server community use-acl
Page 4253
snmp-server contact[no] snmp-server contact [ <line> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
modify sysContactcontact
(Optional) modify sysContactline
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4109
S Commandssnmp-server contact
Page 4254
snmp-server context[no] snmp-server context <context_name> [ instance <instance-name> ] [ vrf { <vrf-name> | <vrf-known-name>} ] [ topology <topology-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
SNMP context to be mappedcontext
name of the SNMP contextcontext_name
(Optional) Protocol instance associated with the SNMP contextinstance
(Optional) Name of the protocol instanceinstance-name
(Optional) VRF associated with the SNMP contextvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Topology associated with the SNMP contexttopology
(Optional) name of the Topologytopology-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4110
S Commandssnmp-server context
Page 4255
snmp-server counter cache enable[no] snmp-server counter cache enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Configure port counter configurationcounter
port stats cachecache
enable port stats cacheenable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4111
S Commandssnmp-server counter cache enable
Page 4256
snmp-server counter cache timeout[no] snmp-server counter cache timeout <timeout>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Configure port counter configurationcounter
Port stats cachecache
Timeout for port stats cachetimeout
Timeout for which cached port stats exists(in secs)timeout
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4112
S Commandssnmp-server counter cache timeout
Page 4257
snmp-server enable traps[no] snmp-server enable traps [ <trap_arg> [ <trap_sub_category> + ] ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable SNMP Trapsenable
Enable SNMP trapstraps
(Optional) Enable __left__ trapstrap_arg
(Optional) Enter the traptrap_sub_category
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4113
S Commandssnmp-server enable traps
Page 4258
snmp-server enable traps bgp[no] snmp-server enable traps bgp [ { state-changes [ <subsystem> + ] } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable SNMP Trapsenable
Enable SNMP trapstraps
Enable SNMP BGP trapsbgp
(Optional) Traps for FSM state changesstate-changes
(Optional) subsystem within BGP for SNMP trapssubsystem
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4114
S Commandssnmp-server enable traps bgp
Page 4259
snmp-server enable traps bgp cbgp2[no] snmp-server enable traps bgp cbgp2 [ { state-changes [ <subsystem> + ] } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable SNMP Trapsenable
Enable SNMP trapstraps
Enable SNMP BGP trapsbgp
Enable SNMP CISCO-BGP-MIBv2 trapscbgp2
(Optional) Traps for FSM state changesstate-changes
(Optional) subsystem within BGP for SNMP trapssubsystem
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4115
S Commandssnmp-server enable traps bgp cbgp2
Page 4260
snmp-server enable traps bgp cbgp2 threshold prefix[no] snmp-server enable traps bgp cbgp2 threshold prefix
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable SNMP Trapsenable
Enable SNMP trapstraps
Enable SNMP BGP trapsbgp
Enable SNMP CISCO-BGP-MIBv2 trapscbgp2
Traps for threshold eventsthreshold
CISCO specific trap for prefix threshold eventsprefix
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4116
S Commandssnmp-server enable traps bgp cbgp2 threshold prefix
Page 4261
snmp-server enable traps bgp threshold prefix[no] snmp-server enable traps bgp threshold prefix
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable SNMP Trapsenable
Enable SNMP trapstraps
Enable SNMP BGP trapsbgp
Traps for threshold eventsthreshold
CISCO specific trap for prefix threshold eventsprefix
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4117
S Commandssnmp-server enable traps bgp threshold prefix
Page 4262
snmp-server enable traps eigrp[no] snmp-server enable traps eigrp [ <eigrp-ptag> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable SNMP Trapsenable
Enable SNMP trapstraps
Enable SNMP EIGRP trapseigrp
(Optional) Process tageigrp-ptag
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4118
S Commandssnmp-server enable traps eigrp
Page 4263
snmp-server enable traps ospf[no] snmp-server enable traps ospf [ <tag> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable SNMP Trapsenable
Enable SNMP trapstraps
Enable SNMP OSPF trapsospf
(Optional) Process tagtag
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4119
S Commandssnmp-server enable traps ospf
Page 4264
snmp-server enable traps ospf lsa[no] snmp-server enable traps ospf [ <tag> ] lsa
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable SNMP Trapsenable
Enable SNMP trapstraps
Enable SNMP OSPF trapsospf
(Optional) Process tagtag
Allow sending LSA trapslsa
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4120
S Commandssnmp-server enable traps ospf lsa
Page 4265
snmp-server enable traps ospf rate-limit{ { no snmp-server enable traps ospf [ <tag> ] rate-limit [ <window> <rate> ] } | { snmp-server enable trapsospf [ <tag> ] rate-limit <window> <rate> } }
Syntax Description
Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable SNMP Trapsenable
Enable SNMP trapstraps
Enable SNMP OSPF trapsospf
(Optional) Process tagtag
Trap rate limit valuesrate-limit
(Optional) Rate limit window size in secondswindow
(Optional) Max number of traps sent in window timerate
(Optional)tag
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4121
S Commandssnmp-server enable traps ospf rate-limit
Page 4266
snmp-server enable traps ospfv3[no] snmp-server enable traps ospfv3 [ <tag> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable SNMP Trapsenable
Enable SNMP trapstraps
Enable SNMP OSPFv3 trapsospfv3
(Optional) Process tagtag
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4122
S Commandssnmp-server enable traps ospfv3
Page 4267
snmp-server enable traps ospfv3 lsa[no] snmp-server enable traps ospfv3 lsa
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable SNMP Trapsenable
Enable SNMP trapstraps
Enable SNMP OSPFv3 trapsospfv3
Enable SNMP OSPFv3 LSA trapslsa
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4123
S Commandssnmp-server enable traps ospfv3 lsa
Page 4268
snmp-server enable traps ospfv3 lsa[no] snmp-server enable traps ospfv3 <tag> lsa
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable SNMP Trapsenable
Enable SNMP trapstraps
Enable SNMP OSPFv3 trapsospfv3
Process tagtag
Enable SNMP OSPFv3 LSA trapslsa
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4124
S Commandssnmp-server enable traps ospfv3 lsa
Page 4269
snmp-server enable traps ospfv3 rate-limit{ { no snmp-server enable traps ospfv3 [ <tag> ] rate-limit } | { snmp-server enable traps ospfv3 [ <tag> ]rate-limit <swindow> <rate> } }
Syntax Description
Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable SNMP Trapsenable
Enable SNMP trapstraps
Enable SNMP OSPFv3 trapsospfv3
(Optional) Process tagtag
Trap rate limit valuesrate-limit
Rate limit window size in secondsswindow
Max number of traps sent in window timerate
(Optional)tag
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4125
S Commandssnmp-server enable traps ospfv3 rate-limit
Page 4270
snmp-server enable traps storm-control trap-rate[no] snmp-server enable traps storm-control trap-rate <rate-per-minute>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable SNMP Trapsenable
Enable SNMP trapstraps
Enable storm-control trapsstorm-control
Number of traps per minutetrap-rate
per Minute (0 means no upper rate)rate-per-minute
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4126
S Commandssnmp-server enable traps storm-control trap-rate
Page 4271
snmp-server engineID localsnmp-server engineID local <engineId> | no snmp-server engineID local [ <engineId> ]
Syntax Description
Negate a command or set its defaultsno
Configure snmp serversnmp-server
Configure a local SNMPv3 engineIDengineID
engineID of the local agentlocal
engine ID should be an even number of hexadecimal characters, whichranges from 10 to 64 where every two hexadecimal characters shouldbe separated by colon. Including colons-
engineId
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4127
S Commandssnmp-server engineID local
Page 4272
snmp-server force-unload-featuresnmp-server force-unload-feature <feature_name>
Syntax Description
Configure snmp serversnmp-server
unload mibs of conditional feature forcefullyforce-unload-feature
conditional feature namefeature_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4128
S Commandssnmp-server force-unload-feature
Page 4273
snmp-server globalEnforcePriv[no] snmp-server globalEnforcePriv
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
globally enforce privacy for all the usersglobalEnforcePriv
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4129
S Commandssnmp-server globalEnforcePriv
Page 4274
snmp-server host[no] snmp-server host <host0> { <s6> | [ informs | traps ] { { version { 1 <s0> | 2c <s1> | 3 { auth <s2> |noauth <s3> | priv <s4> } } } | <s5> } } [ udp-port <i1> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Specify hosts to receive SNMP notificationshost
IPv4 or IPv6 address or DNS Name of SNMP notification hosthost0
(Optional) Send Inform messages to this hostinforms
(Optional) Send Traps messages to this hosttraps
SNMP version to use for notification messagesversion
Use SNMPv11
SNMP community string or SNMPv3 user names0
(Optional) The notification host's UDP port numberudp-port
(Optional) The notification host's UDP port numberi1
Use SNMPv2c2c
SNMP community string or SNMPv3 user names1
Use SNMPv33
Use the SNMPv3 authNoPriv Security Levelauth
SNMP community string or SNMPv3 user names2
Use the SNMPv3 noAuthNoPriv Security Levelnoauth
SNMP community string or SNMPv3 user names3
Use the SNMPv3 authPriv Security Levelpriv
SNMP community string or SNMPv3 user names4
SNMP community string or SNMPv3 user names5
SNMP community string or SNMPv3 user names6
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4130
S Commandssnmp-server host
Page 4275
snmp-server host filter-vrf[no] snmp-server host <host0> filter-vrf { <vrf-name> | <vrf-known-name> } [ udp-port <i1> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Specify hosts to receive SNMP notificationshost
IPv4 or IPv6 address or DNS Name of SNMP notification hosthost0
Filters notifications to the notification host receiver based on theconfigured VRF
filter-vrf
VRF namevrf-name
Known VRF namevrf-known-name
(Optional) The notification host's UDP port numberudp-port
(Optional) The notification host's UDP port numberi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4131
S Commandssnmp-server host filter-vrf
Page 4276
snmp-server host source[no] snmp-server host <host0> { source-interface <ifName> } [ udp-port <i1> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Specify hosts to send SNMP notificationshost
IPv4 or IPv6 address or DNS Name of SNMP notification hosthost0
Source interface to be used for sending out SNMP notifications to thishost
source-interface
Source interface nameifName
(Optional) The notification host's UDP port numberudp-port
(Optional) The notification host's UDP port numberi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4132
S Commandssnmp-server host source
Page 4277
snmp-server host use-vrf[no] snmp-server host <host0> use-vrf { <vrf-name> | <vrf-known-name> } [ udp-port <i1> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Specify hosts to receive SNMP notificationshost
IPv4 or IPv6 address or DNS Name of SNMP notification hosthost0
Configures SNMP to use the selected VRF to communicate with thehost receiver
use-vrf
VRF namevrf-name
Known VRF namevrf-known-name
(Optional) The notification host's UDP port numberudp-port
(Optional) The notification host's UDP port numberi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4133
S Commandssnmp-server host use-vrf
Page 4278
snmp-server host use_vrf[no] snmp-server host <host0> { use_vrf <s0> | filter_vrf <s1> } [ udp-port <i1> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Specify hosts to receive SNMP notificationshost
IPv4 or IPv6 address or DNS Name of SNMP notification hosthost0
Configures SNMP to use the selected VRF to communicate with thehost receiver
use_vrf
VRF names0
Filters notifications to the notification host receiver based on theconfigured VRF
filter_vrf
VRF names1
(Optional) The notification host's UDP port numberudp-port
(Optional) The notification host's UDP port numberi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4134
S Commandssnmp-server host use_vrf
Page 4279
snmp-server load-cond-feature[no] snmp-server load-cond-feature <feature_name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
load or unload mibs of conditional featureload-cond-feature
conditional feature namefeature_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4135
S Commandssnmp-server load-cond-feature
Page 4280
snmp-server load-mib[no] snmp-server load-mib <mib_name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
load a given mibload-mib
mib module namemib_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4136
S Commandssnmp-server load-mib
Page 4281
snmp-server location[no] snmp-server location [ <line> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
modify sysLocationlocation
(Optional) modify sysLocationline
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4137
S Commandssnmp-server location
Page 4282
snmp-server mib community-map context[no] snmp-server mib community-map <community_name> context <context_name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
mib access parametersmib
SNMP communitycommunity-map
SNMP community stringcommunity_name
SNMP context to be mappedcontext
name of the SNMP contextcontext_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4138
S Commandssnmp-server mib community-map context
Page 4283
snmp-server protocol enable[no] snmp-server protocol enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
snmp protocol operationsprotocol
Enable/Disable snmp protocol operationsenable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4139
S Commandssnmp-server protocol enable
Page 4284
snmp-server source-interface informs[no] snmp-server source-interface { informs } <ifName>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Source interface to be used for sending out SNMP notificationssource-interface
Source interface nameifName
SNMP Inform notifications for which this source interface needs to beused
informs
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4140
S Commandssnmp-server source-interface informs
Page 4285
snmp-server source-interface traps[no] snmp-server source-interface { traps } <ifName>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Source interface to be used for sending out SNMP notificationssource-interface
Source interface nameifName
SNMP Trap notifications for which this source interface needs to beused
traps
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4141
S Commandssnmp-server source-interface traps
Page 4286
snmp-server system-shutdown[no] snmp-server system-shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Configure snmp-server for reload(2)system-shutdown
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4142
S Commandssnmp-server system-shutdown
Page 4287
snmp-server tcp-session[no] snmp-server tcp-session [ auth ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Enable one time authentication for snmp over tcp session.tcp-session
(Optional) Enable one time authentication for snmp over tcp session.auth
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4143
S Commandssnmp-server tcp-session
Page 4288
snmp-server user{ no snmp-server user <user_name> { use-ipv4acl [ <ipv4_acl_name> ] use-ipv6acl [ <ipv6_acl_name> ] |use-ipv4acl [ <ipv4_acl_name> ] | use-ipv6acl [ <ipv6_acl_name> ] } | snmp-server user <user_name> {use-ipv4acl <ipv4_acl_name> use-ipv6acl <ipv6_acl_name> | use-ipv4acl <ipv4_acl_name> | use-ipv6acl<ipv6_acl_name> } }
Syntax Description
Negate a command or set its defaultsno
Configure snmp serversnmp-server
Define a user who can access the SNMP engineuser
Name of the useruser_name
Specify IPv4 ACL, the ACL name specified after must be IPv4 ACL.use-ipv4acl
(Optional) IPv4 ACL name to filter snmp requestsipv4_acl_name
Specify IPv6 ACL, the ACL name specified after must be IPv6 ACL.use-ipv6acl
(Optional) IPv6 ACL name to filter snmp requestsipv6_acl_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4144
S Commandssnmp-server user
Page 4289
snmp-server user[no] snmp-server user <s0> { enforcePriv | { [ <s1> ] { [ auth { md5 | sha } <s2> { { priv [ aes-128 ] { <s3>[ localizedkey ] [ { auto | engineID <s4> } ] } } | { [ localizedkey1 ] [ { auto1 | engineID1 <s5> } ] } } ] } }}
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmp serversnmp-server
Define a user who can access the SNMP engineuser
Name of the users0
Enforce privacy for the userenforcePriv
(Optional) Group name (ignored for notif target user)s1
(Optional) authentication parameters for the userauth
(Optional) Use HMAC MD5 algorithm for authenticationmd5
(Optional) Use HMAC SHA algorithm for authenticationsha
(Optional) authentication password for users2
(Optional) encryption parameters for the userpriv
(Optional) Use 128-bit AES algorithm for privacyaes-128
(Optional) privacy password for users3
(Optional) specifies whether the passwords are in localized key formatlocalizedkey
(Optional) specifies whether the user is auto created (volatile)auto
(Optional) engineID for configuring notif target user (for V3 informs)engineID
(Optional) Specifies notification target's SNMP engineID.Should be anoctet of either Decimal (range: 0 to 255) or Hexadecimal(range: 0 toFF) value, each octet being separated by colon. Hexadecimal valueshould have prefix of 0x or 0X. Including colons-
s4
(Optional) specifies whether the passwords are in localized key formatlocalizedkey1
(Optional) specifies whether the user is auto created (volatile)auto1
(Optional) engineID for configuring notif target user (for V3 informs)engineID1
(Optional) Specifies notification target's SNMP engineID.Should be anoctet of either Decimal (range: 0 to 255) or Hexadecimal(range: 0 toFF) value, each octet being separated by colon. Hexadecimal valueshould have prefix of 0x or 0X. Including colons-
s5
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4145
S Commandssnmp-server user
Page 4290
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4146
S Commandssnmp-server user
Page 4291
snmp ifmib ifalias long[no] snmp ifmib ifalias long
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure snmpsnmp
Configure snmp interface mib featureifmib
Configure snmp interface alias attribute for interface mibifalias
Enable long description up to 256 characters for interface aliaslong
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4147
S Commandssnmp ifmib ifalias long
Page 4292
snmp trap link-statussnmp trap link-status | no snmp trap link-status
Syntax Description
Negate a command or set its defaultsno
Modify SNMP interface parameterssnmp
Allow a specific SNMP traptrap
Allow SNMP LINKUP and LINKDOWN trapslink-status
Command Mode
• /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4148
S Commandssnmp trap link-status
Page 4293
snmp trap link-statussnmp trap link-status | no snmp trap link-status
Syntax Description
Negate a commandno
Modify SNMP interface parameterssnmp
Allow a specific SNMP traptrap
Allow SNMP LINKUP and LINKDOWN trapslink-status
Command Mode
• /exec/configure/if-any-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4149
S Commandssnmp trap link-status
Page 4294
snmp trap link-statussnmp trap link-status | no snmp trap link-status
Syntax Description
Negate a command or set its defaultsno
Modify SNMP interface parameterssnmp
Allow a specific SNMP traptrap
Allow SNMP LINKUP and LINKDOWN trapslink-status
Command Mode
• /exec/configure/if-vlan-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4150
S Commandssnmp trap link-status
Page 4295
snmp trap link-statussnmp trap link-status | no snmp trap link-status
Syntax Description
Negate a command or set its defaultsno
Modify SNMP interface parameterssnmp
Allow a specific SNMP traptrap
Allow SNMP LINKUP and LINKDOWN trapslink-status
Command Mode
• /exec/configure/if-ether-sub /exec/configure/if-port-channel-sub /exec/configure/if-gig-ether-sub/exec/configure/if-remote-ethernet-sub /exec/configure/if-ether-sub-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4151
S Commandssnmp trap link-status
Page 4296
snmp trap link-statussnmp trap link-status
Syntax Description
Modify SNMP interface parameterssnmp
Allow a specific SNMP traptrap
Allow SNMP LINKUP and LINKDOWN trapslink-status
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel/exec/configure/if-port-channel-range
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4152
S Commandssnmp trap link-status
Page 4297
snmp trap link-status[no] snmp trap link-status
Syntax Description
Negate a command or set its defaultsno
Modify SNMP interface parameterssnmp
Allow a specific SNMP traptrap
Allow SNMP LINKUP and LINKDOWN trapslink-status
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base /exec/configure/if-port-channel/exec/configure/if-port-channel-range
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4153
S Commandssnmp trap link-status
Page 4298
snsr-grp sample-intervalsnsr-grp <sn-grp-id> sample-interval <cadence> | no snsr-grp <sn-grp-id>
Syntax Description
Negate a command or set its defaultsno
Associated sensor groupsnsr-grp
Cadence Time in milliseconds(0 for events)sample-interval
Identifiersn-grp-id
Cadence Time in millisecondscadence
Command Mode
• /exec/configure/telemetry/subscription
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4154
S Commandssnsr-grp sample-interval
Page 4299
sockets local-port-range{ { no sockets local-port-range } | { sockets local-port-range <start-port> <end-port> } }
Syntax Description
Negate a command or set its defaultsno
Negate a command or set its defaultssockets
Define local port range for Kstack. Note: This CLI requires switch tobe reloaded
local-port-range
Start port of local port rangestart-port
End port of local port rangeend-port
Command Mode
• /exec/configure /exec/configure/config-mgmt
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4155
S Commandssockets local-port-range
Page 4300
soft-reconfiguration inbound{ soft-reconfiguration inbound [ always ] } | { no soft-reconfiguration inbound } | { default soft-reconfigurationinbound }
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Soft reconfigurationsoft-reconfiguration
Allow inbound soft reconfigurationinbound
(Optional) Always perform inbound soft reconfigurationalways
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mvpn/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-mvpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4156
S Commandssoft-reconfiguration inbound
Page 4301
soft-reconfiguration inbound{ soft-reconfiguration inbound [ always ] } | { no soft-reconfiguration inbound } | { default soft-reconfigurationinbound }
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Soft reconfigurationsoft-reconfiguration
Allow inbound soft reconfigurationinbound
(Optional) Always perform inbound soft reconfigurationalways
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4157
S Commandssoft-reconfiguration inbound
Page 4302
soo auto{ [ no ] soo { auto | <ext-comm-soo-aa2nn4> | <ext-comm-soo-aa4nn2> } } | { default soo }
Syntax Description
(Optional) Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Specify Site-of-origin extcommunitysoo
Generate SOO automaticallyauto
VPN extcommunity in aa4:nn or ip:nn formatext-comm-soo-aa4nn2
VPN extcommunity in aa:nn formatext-comm-soo-aa2nn4
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv4/exec/configure/router-bgp/router-bgp-vrf-neighbor/router-bgp-vrf-neighbor-af-ipv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4158
S Commandssoo auto
Page 4303
sort| sort [ -b | -d | -f | -g | -i | -M | -n | -r | -k <key> | -t <delim> | -u ] +
Syntax Description
Pipe command output to filter|
Stream Sortersort
(Optional) ignore leading blanks-b
(Optional) consider only blanks and alphanumeric characters-d
(Optional) fold lower case to upper case characters-f
(Optional) compare according to general numerical value-g
(Optional) consider only printable characters-i
(Optional) month sort-M
(Optional) compare according to string numerical value-n
(Optional) reverse the result of comparisons-r
(Optional) provide a key-k
(Optional) use different separator instead of non-blank to blank transition-t
(Optional) remove duplicate lines-u
(Optional) key in format POS1[,POS2] with POS =<field-nb>[.<char-pos>][<ordering>]
key
(Optional) field delimiter chardelim
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4159
S Commandssort
Page 4304
source-address ipv4[no] source-address ipv4 [ <ip-address> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure the source address to be used for PCE connectionsource-address
Configure v4 source address for PCCipv4
(Optional) Source addressip-address
Command Mode
• /exec/configure/sr/te/pcc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4160
S Commandssource-address ipv4
Page 4305
source-group[no] source-group <source> <group>
Syntax Description
(Optional) Negate a command or set its defaultsno
Source Groupsource-group
Configure source addresssource
Configure group addressgroup
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4161
S Commandssource-group
Page 4306
source-interface[no] source-interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure source interface to reach http serversource-interface
Interfaceinterface
Command Mode
• /exec/configure/trustpool
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4162
S Commandssource-interface
Page 4307
source-interfacesource-interface <interface> | no source-interface
Syntax Description
Negate a command or set its defaultsno
NVE Source-Interfacesource-interface
interface
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4163
S Commandssource-interface
Page 4308
source-interfacesource-interface <interface> | no source-interface
Syntax Description
Negate a command or set its defaultsno
Source interfacesource-interface
Interface nameinterface
Command Mode
• /exec/configure/telemetry/destination-profile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4164
S Commandssource-interface
Page 4309
source-interface[no] source-interface | source-interface <interface>
Syntax Description
Negate a command or set its defaultsno
Source interface to be used to reach radius serversource-interface
Interface (default is mgmt)interface
Command Mode
• /exec/configure/radius
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4165
S Commandssource-interface
Page 4310
source-interface[no] source-interface | source-interface <interface>
Syntax Description
Negate a command or set its defaultsno
Source interface to be used to reach tacacs serversource-interface
Interface (default is mgmt)interface
Command Mode
• /exec/configure/tacacs+
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4166
S Commandssource-interface
Page 4311
source-interface[no] source-interface <interface>
Syntax Description
(Optional) Negate a command or set its defaultsno
PLB probe Source-Interfacesource-interface
source interface for probeinterface
Command Mode
• /exec/configure/plb
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4167
S Commandssource-interface
Page 4312
source-interface hold-down-time[no] source-interface hold-down-time <sec>
Syntax Description
(Optional) Negate a command or set its defaultsno
NVE Source-Interfacesource-interface
Hold source loopback down timehold-down-time
time in secondssec
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4168
S Commandssource-interface hold-down-time
Page 4313
source{ [ no ] source <intf> | no source }
Syntax Description
Source Interface for this destinationsource
Interfaceintf
Command Mode
• /exec/configure/config-postcard-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4169
S Commandssource
Page 4314
source{ [ no ] source <intf> | no source }
Syntax Description
Source Interface for this destinationsource
Interfaceintf
Command Mode
• /exec/configure/config-int-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4170
S Commandssource
Page 4315
source{ [ no ] source { <ipaddr> | <ipv6addr> } }
Syntax Description
Specify detailssource
Source IP address for collectoripaddr
Command Mode
• /exec/configure/config-fte-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4171
S Commandssource
Page 4316
source{ [ no ] source <intf> | no source }
Syntax Description
Source Interface for this destinationsource
Interfaceintf
Command Mode
• /exec/configure/nfm-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4172
S Commandssource
Page 4317
sourcesource <srcip> | no source
Syntax Description
Negate a command or set its defaultsno
Source address for connection to controllerssource
IP address of sourcesrcip
Command Mode
• /exec/configure/openflow/switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4173
S Commandssource
Page 4318
source[no] source { { unicast-queue interface <if_list> qos-group <qos-grp> } | { { ingress | egress } { interface<if_list> } } }
Syntax Description
(Optional) Negate the commandno
Configure Packet Drop Scopesource
Specify Capture scope as queue basisunicast-queue
Specify interface associated to particular Queueinterface
List of interfacesif_list
Specify the Qos-grp to be associatedqos-group
Value 0-7qos-grp
Specify Capture scope as Ingressingress
Specify Capture scope as Egressegress
Configure the Entity Interfaceinterface
List of interfacesif_list
Command Mode
• /exec/configure/pkt-drop
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4174
S Commandssource
Page 4319
source[no] source <ipaddr>
Syntax Description
Source configurationsource
IP Address to be configuredipaddr
Command Mode
• /exec/configure/config-ssx-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4175
S Commandssource
Page 4320
sourcesource [ background ] <file> [ <args> ] +
Syntax Description
run a script (python, tcl,...) from bootflash:scriptssource
(Optional) run the script in the background, see also 'show background'and 'kill background
background
the script file to runfile
(Optional) argument to be passed to scriptargs
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4176
S Commandssource
Page 4321
source| source <file> [ <args> ] +
Syntax Description
Pipe command output to filter|
run a script (python, tcl,...) from bootflash:scriptssource
the script file to runfile
(Optional) argument to be passed to scriptargs
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4177
S Commandssource
Page 4322
sourcesource { <ipaddr> } | no source
Syntax Description
Negate a command or set its defaultsno
source of tunnel packetssource
ip address (A.B.C.D)ipaddr
Command Mode
• /exec/configure/if-te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4178
S Commandssource
Page 4323
source{ source { <numeric1> | <numeric2> } | no source }
Syntax Description
Negate a command or set its defaultsno
Sourcesource
IPnumeric1
Command Mode
• /exec/configure/configngoamconnectcheck
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4179
S Commandssource
Page 4324
source copy-syssource copy-sys
Syntax Description
run a script (python, tcl,...) from bootflash:scriptssource
copy the system provided example scripts of /sys to bootflash:scriptscopy-sys
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4180
S Commandssource copy-sys
Page 4325
source filter ip[no] source filter ip { <ip-addr> <ip-mask> } [ ip | { { udp | tcp } { <port_num> | any } } ] [ { arp | advertise} { enable | disable } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
source ip configurationsource
source filtersfilter
source ipip
IP address in format i.i.i.iip-addr
IP network mask in format m.m.m.mip-mask
(Optional) IP Protocolip
(Optional) UDP Protocoludp
(Optional) TCP Protocoltcp
(Optional) Port Numberport_num
(Optional) Any Port Numberany
(Optional) ARParp
(Optional) advertiseadvertise
(Optional) Enableenable
(Optional) Disabledisable
Command Mode
• /exec/configure/smartc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4181
S Commandssource filter ip
Page 4326
source filter ip any any[no] source filter ip any any
Syntax Description
(Optional) Negate a command or set its defaultsno
source ip configurationsource
source filtersfilter
source ipip
Any IPany
Command Mode
• /exec/configure/smartc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4182
S Commandssource filter ip any any
Page 4327
source forward-drops[no] source forward-drops <src_dir> [ priority-low ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Source configurationsource
Forwarding dropsforward-drops
(Optional) Drop span session is low priority relative to span acl and vlansessions
priority-low
Source directionsrc_dir
Command Mode
• /exec/configure/monitor-local-src /exec/configure/config-monitor/exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4183
S Commandssource forward-drops
Page 4328
source group permit{ <seq> source <sourceip> group <range> { permit | deny } } | { no <seq> [ source <sourceip> group <range>{ permit | deny } ] }
Syntax Description
Sequence Numberseq
Source IP Addresssource
Source IP Address valuesourceip
Configure explicit group rangesgroup
Group Prefixrange
Admission Permittedpermit
Admission Denieddeny
Command Mode
• /exec/configure/nbm-host-policy/pim
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4184
S Commandssource group permit
Page 4329
source interface[no] source { interface <interface_range> } [ <src_dir> ] [ allow-pfc ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Source configurationsource
Configure interfacesinterface
interface_range
(Optional) Source directionsrc_dir
(Optional) Enable SPAN on PFC framesallow-pfc
Command Mode
• /exec/configure/monitor-local-src /exec/configure/config-monitor/exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4185
S Commandssource interface
Page 4330
source interface[no] source { interface <interface> } [ <src_dir> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Source configurationsource
Configure interfacesinterface
interface
(Optional) Source directionsrc_dir
Command Mode
• /exec/configure/monitor-local-src /exec/configure/config-monitor/exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4186
S Commandssource interface
Page 4331
source ip[no] source ip <ipaddress>
Syntax Description
(Optional) Negate a command or set its defaultsno
Source IP address configurationsource
Configure source IP addressip
ipaddress
Command Mode
• /exec/configure/config-monitor-erspan-dst
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4187
S Commandssource ip
Page 4332
source vlan[no] source { vlan <vlan_range> | vsan <vsan_range> } [ <src_dir> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Source configurationsource
Vlan typevlan
Vsan typevsan
vlan_range
vsan_range
(Optional) Source directionsrc_dir
Command Mode
• /exec/configure/monitor-local-src /exec/configure/config-monitor/exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4188
S Commandssource vlan
Page 4333
spanning-tree bpdufilterspanning-tree bpdufilter <port-bpdufilter> | no spanning-tree bpdufilter [ <port-bpdufilter> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Don't send or receive BPDUs on this interfacebpdufilter
Don't send or receive BPDUs on this interfaceport-bpdufilter
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4189
S Commandsspanning-tree bpdufilter
Page 4334
spanning-tree bpduguardspanning-tree bpduguard <port-bpduguard> | no spanning-tree bpduguard [ <port-bpduguard> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Don't accept BPDUs on this interfacebpduguard
Don't accept BPDUs on this interfaceport-bpduguard
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4190
S Commandsspanning-tree bpduguard
Page 4335
spanning-tree bridge-domain[no] spanning-tree bridge-domain <bd-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Bridge-Domain Switch Spanning Treesbridge-domain
Bridge-Domain range, Example: 2,4-5,7,9-11bd-id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4191
S Commandsspanning-tree bridge-domain
Page 4336
spanning-tree bridge assurance[no] spanning-tree bridge assurance
Syntax Description
(Optional) Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Spanning tree bridge optionsbridge
Enable Bridge Assurance on all network portsassurance
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4192
S Commandsspanning-tree bridge assurance
Page 4337
spanning-tree costspanning-tree [ vlan <vlan-id> | bridge-domain <bd-id> ] cost <port-cost> | no spanning-tree [ vlan <vlan-id>| bridge-domain <bd-id> ] cost [ <port-cost> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
(Optional) VLAN Switch Spanning Treesvlan
(Optional) Bridge-Domain Switch Spanning Treesbridge-domain
(Optional) vlan range, Example: 1,3-5,7,9-11vlan-id
(Optional) vlan range, Example: 1,3-5,7,9-11vlan-id
(Optional) Bridge-Domain range, Example: 2,4-5,7,9-11bd-id
Change an interface's spanning tree port path costcost
port path costport-cost
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4193
S Commandsspanning-tree cost
Page 4338
spanning-tree cost auto[no] spanning-tree [ vlan <vlan-id> | bridge-domain <bd-id> ] cost auto
Syntax Description
(Optional) Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
(Optional) VLAN Switch Spanning Treesvlan
(Optional) Bridge-Domain Switch Spanning Treesbridge-domain
(Optional) vlan range, Example: 1,3-5,7,9-11vlan-id
(Optional) Bridge-Domain range, Example: 2,4-5,7,9-11bd-id
Change an interface's spanning tree port path costcost
Determine cost based on media speed of this interfaceauto
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4194
S Commandsspanning-tree cost auto
Page 4339
spanning-tree domainspanning-tree domain { enable | disable | <domain-id> } | no spanning-tree domain [ enable ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Spanning Tree Domaindomain
Enable Spanning Tree Domainenable
Disable Spanning Tree Domaindisable
Domain Identifierdomain-id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4195
S Commandsspanning-tree domain
Page 4340
spanning-tree domain clear statisticsspanning-tree domain clear statistics
Syntax Description
Spanning Tree Subsystemspanning-tree
Spanning Tree Domaindomain
Clearclear
Clear Statisticsstatistics
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4196
S Commandsspanning-tree domain clear statistics
Page 4341
spanning-tree fcoe[no] spanning-tree fcoe
Syntax Description
(Optional) Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Enable STP for FCoE VLANsfcoe
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4197
S Commandsspanning-tree fcoe
Page 4342
spanning-tree guardspanning-tree guard <guard-type> | no spanning-tree guard [ <guard-type> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Change an interface's spanning tree guard modeguard
Change an interface's spanning tree guard modeguard-type
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4198
S Commandsspanning-tree guard
Page 4343
spanning-tree lc-issuspanning-tree lc-issu <issu-type> | no spanning-tree lc-issu [ <issu-type> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Configure Linecard ISSU typelc-issu
ISSU Typeissu-type
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4199
S Commandsspanning-tree lc-issu
Page 4344
spanning-tree lc-issuspanning-tree lc-issu <port-issu-type> | no spanning-tree lc-issu [ <port-issu-type> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Configure Linecard ISSU typelc-issu
ISSU Typeport-issu-type
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4200
S Commandsspanning-tree lc-issu
Page 4345
spanning-tree link-typespanning-tree link-type <link-type-val> | no spanning-tree link-type [ <link-type-val> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Specify a link type for spanning tree tree protocol uselink-type
Specify a link type for spanning tree tree protocol uselink-type-val
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4201
S Commandsspanning-tree link-type
Page 4346
spanning-tree loopguard default[no] spanning-tree loopguard default
Syntax Description
(Optional) Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Spanning tree loopguard optionsloopguard
Enable loopguard by default on all portsdefault
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4202
S Commandsspanning-tree loopguard default
Page 4347
spanning-tree modespanning-tree mode <stp-mode> | no spanning-tree mode [ <stp-mode> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Spanning Tree operating modemode
Spanning Tree operating modestp-mode
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4203
S Commandsspanning-tree mode
Page 4348
spanning-tree mst configurationspanning-tree mst configuration
Syntax Description
Spanning Tree Subsystemspanning-tree
Multiple spanning tree configurationmst
Enter MST configuration submodeconfiguration
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4204
S Commandsspanning-tree mst configuration
Page 4349
spanning-tree mst configuration[no] spanning-tree mst configuration
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Multiple spanning tree configurationmst
Enter MST configuration submodeconfiguration
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4205
S Commandsspanning-tree mst configuration
Page 4350
spanning-tree mst costspanning-tree mst <mst-id> cost <port-cost> | no spanning-tree mst <mst-id> cost [ <port-cost> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Multiple spanning treemst
MST instance list, example 0,2-4,6,8-12mst-id
Change an interface's spanning tree port path costcost
port path costport-cost
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4206
S Commandsspanning-tree mst cost
Page 4351
spanning-tree mst cost auto[no] spanning-tree mst <mst-id> cost auto
Syntax Description
(Optional) Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Multiple spanning treemst
MST instance list, example 0,2-4,6,8-12mst-id
Change an interface's spanning tree port path costcost
Determine cost based on media speed of this interfaceauto
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4207
S Commandsspanning-tree mst cost auto
Page 4352
spanning-tree mst forward-timespanning-tree mst forward-time <fwd-time> | no spanning-tree mst forward-time [ <fwd-time> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Multiple spanning tree configurationmst
Set the forward delay for the spanning treeforward-time
number of seconds for the forward delay timerfwd-time
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4208
S Commandsspanning-tree mst forward-time
Page 4353
spanning-tree mst hello-timespanning-tree mst hello-time <hello-time-val> | no spanning-tree mst hello-time [ <hello-time-val> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Multiple spanning tree configurationmst
Set the hello interval for the spanning treehello-time
number of seconds between generation of config bpduhello-time-val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4209
S Commandsspanning-tree mst hello-time
Page 4354
spanning-tree mst max-agespanning-tree mst max-age <max-age-val> | no spanning-tree mst max-age [ <max-age-val> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Multiple spanning tree configurationmst
Set the max age interval for the spanning treemax-age
maximum number of seconds the information in a bpdu is validmax-age-val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4210
S Commandsspanning-tree mst max-age
Page 4355
spanning-tree mst max-hopsspanning-tree mst max-hops <max-hops-val> | no spanning-tree mst max-hops [ <max-hops-val> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Multiple spanning tree configurationmst
Set the max hops value for the spanning treemax-hops
maximum number of hops a BPDU is validmax-hops-val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4211
S Commandsspanning-tree mst max-hops
Page 4356
spanning-tree mst port-priorityspanning-treemst <mst-id> port-priority <port-prio> | no spanning-treemst <mst-id> port-priority [ <port-prio>]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Multiple spanning treemst
MST instance list, example 0,2-4,6,8-12mst-id
Change an interface's spanning tree port priorityport-priority
Spanning-tree port priorityport-prio
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4212
S Commandsspanning-tree mst port-priority
Page 4357
spanning-tree mst pre-standard[no] spanning-tree mst pre-standard
Syntax Description
(Optional) Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Multiple spanning treemst
Force pre-standard MST BPDU transmission on portpre-standard
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4213
S Commandsspanning-tree mst pre-standard
Page 4358
spanning-tree mst priorityspanning-tree mst <mst-id> priority <prio> | no spanning-tree mst <mst-id> priority [ <prio> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Multiple spanning tree configurationmst
MST instance range, example: 0-3,5,7-9mst-id
Set the bridge priority for the spanning treepriority
bridge priority in increments of 4096prio
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4214
S Commandsspanning-tree mst priority
Page 4359
spanning-tree mst rootspanning-tree mst <mst-id> root <root-type> [ diameter <diameter-val> [ hello-time <hello-time-val> ] ] | nospanning-tree mst <mst-id> root [ <root-type> [ diameter <diameter-val> [ hello-time <hello-time-val> ] ] ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Multiple spanning tree configurationmst
MST instance range, example: 0-3,5,7-9mst-id
(Optional) Network diameter of this spanning treediameter
(Optional) Maximum number of bridges between any two end nodesdiameter-val
configure switch as rootroot
configure switch as rootroot-type
(Optional) Set the hello interval for the spanning treehello-time
(Optional) number of seconds between generation of config bpduhello-time-val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4215
S Commandsspanning-tree mst root
Page 4360
spanning-tree mst simulate pvst[no] spanning-tree mst simulate pvst [ <simpvst-disable> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Multiple spanning treemst
Enable spanning tree simulationsimulate
Enable PVST simulationpvst
(Optional) Disable PVST simulation on this interfacesimpvst-disable
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4216
S Commandsspanning-tree mst simulate pvst
Page 4361
spanning-tree mst simulate pvst global[no] spanning-tree mst simulate pvst global
Syntax Description
(Optional) Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Multiple spanning tree configurationmst
Enable spanning tree simulationsimulate
Enable PVST simulationpvst
Enable PVST Simulation by default on all portsglobal
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4217
S Commandsspanning-tree mst simulate pvst global
Page 4362
spanning-tree pathcost methodspanning-tree pathcost method <method-val> | no spanning-tree pathcost method [ <method-val> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Spanning tree pathcost optionspathcost
Method to calculate default port path costmethod
Method to calculate default port path costmethod-val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4218
S Commandsspanning-tree pathcost method
Page 4363
spanning-tree port-priorityspanning-tree [ vlan <vlan-id> | bridge-domain <bd-id> ] port-priority <port-prio> | no spanning-tree [ vlan<vlan-id> | bridge-domain <bd-id> ] port-priority [ <port-prio> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
(Optional) VLAN Switch Spanning Treesvlan
(Optional) Bridge-Domain Switch Spanning Treesbridge-domain
(Optional) vlan range, Example: 1,3-5,7,9-11vlan-id
(Optional) Bridge-Domain range, Example: 2,4-5,7,9-11bd-id
Change an interface's spanning tree port priorityport-priority
Spanning-tree port priorityport-prio
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4219
S Commandsspanning-tree port-priority
Page 4364
spanning-tree port typespanning-tree port type <port-type> | no spanning-tree port type [ <port-type> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Spanning tree port optionsport
Specify a port type for spanning tree protocol usetype
Specify a port type for spanning tree protocol useport-type
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4220
S Commandsspanning-tree port type
Page 4365
spanning-tree port type edge bpdufilter default[no] spanning-tree port type edge bpdufilter default
Syntax Description
(Optional) Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Spanning tree port optionsport
Specify a port type for spanning tree protocol usetype
Consider the interface as edge port (enable portfast)edge
Enable edge port (portfast) bpdu filter on this switchbpdufilter
Enable bdpu filter by default on all edge (portfast) portsdefault
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4221
S Commandsspanning-tree port type edge bpdufilter default
Page 4366
spanning-tree port type edge bpduguard default[no] spanning-tree port type edge bpduguard default
Syntax Description
(Optional) Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Spanning tree port optionsport
Specify a port type for spanning tree protocol usetype
Consider the interface as edge port (enable portfast)edge
Enable edge port (portfast) bpdu guard on this switchbpduguard
Enable bdpu guard by default on all edge (portfast) portsdefault
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4222
S Commandsspanning-tree port type edge bpduguard default
Page 4367
spanning-tree port type edge default[no] spanning-tree port type edge default
Syntax Description
(Optional) Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Spanning tree port optionsport
Specify a port type for spanning tree protocol usetype
Consider the interface as edge port (enable portfast)edge
Select edge port type by default on all access portsdefault
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4223
S Commandsspanning-tree port type edge default
Page 4368
spanning-tree port type edge trunkspanning-tree port type edge trunk | no spanning-tree port type edge trunk
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Spanning tree port optionsport
Specify a port type for spanning tree protocol usetype
Consider the interface as edge port (enable portfast)edge
Consider the interface as edge port (enable portfast) even in trunk modetrunk
Command Mode
• /exec/configure/if-switching /exec/configure/if-ethernet-switch-m
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4224
S Commandsspanning-tree port type edge trunk
Page 4369
spanning-tree port type network default[no] spanning-tree port type network default
Syntax Description
(Optional) Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
Spanning tree port optionsport
Specify a port type for spanning tree protocol usetype
Consider the interface as inter-switch linknetwork
Select network port type by default on all portsdefault
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4225
S Commandsspanning-tree port type network default
Page 4370
spanning-tree pseudo-informationspanning-tree pseudo-information
Syntax Description
Spanning Tree Subsystemspanning-tree
configure spanning tree pseudo informationpseudo-information
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4226
S Commandsspanning-tree pseudo-information
Page 4371
spanning-tree vlan[no] spanning-tree vlan <vlan-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
VLAN Switch Spanning Treesvlan
vlan range, Example: 1,3-5,7,9-11vlan-id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4227
S Commandsspanning-tree vlan
Page 4372
spanning-tree vlan forward-timespanning-tree { vlan <vlan-id> | bridge-domain <bd-id> } forward-time <fwd-time> | no spanning-tree { vlan<vlan-id> | bridge-domain <bd-id> } forward-time [ <fwd-time> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
VLAN Switch Spanning Treesvlan
Bridge-Domain Switch Spanning Treesbridge-domain
vlan range, Example: 1,3-5,7,9-11vlan-id
Bridge-Domain range, Example: 2,4-5,7,9-11bd-id
Set the forward delay for the spanning treeforward-time
number of seconds for the forward delay timerfwd-time
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4228
S Commandsspanning-tree vlan forward-time
Page 4373
spanning-tree vlan hello-timespanning-tree { vlan <vlan-id> | bridge-domain <bd-id> } hello-time <hello-time-val> | no spanning-tree {vlan <vlan-id> | bridge-domain <bd-id> } hello-time [ <hello-time-val> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
VLAN Switch Spanning Treesvlan
Bridge-Domain Switch Spanning Treesbridge-domain
vlan range, Example: 1,3-5,7,9-11vlan-id
Bridge-Domain range, Example: 2,4-5,7,9-11bd-id
Set the hello interval for the spanning treehello-time
number of seconds between generation of config bpduhello-time-val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4229
S Commandsspanning-tree vlan hello-time
Page 4374
spanning-tree vlan max-agespanning-tree { vlan <vlan-id> | bridge-domain <bd-id> } max-age <max-age-val> | no spanning-tree { vlan<vlan-id> | bridge-domain <bd-id> } max-age [ <max-age-val> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
VLAN Switch Spanning Treesvlan
Bridge-Domain Switch Spanning Treesbridge-domain
vlan range, Example: 1,3-5,7,9-11vlan-id
Bridge-Domain range, Example: 2,4-5,7,9-11bd-id
Set the max age interval for the spanning treemax-age
maximum number of seconds the information in a bpdu is validmax-age-val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4230
S Commandsspanning-tree vlan max-age
Page 4375
spanning-tree vlan priorityspanning-tree { vlan <vlan-id> | bridge-domain <bd-id> } priority <prio> | no spanning-tree { vlan <vlan-id>| bridge-domain <bd-id> } priority [ <prio> ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
VLAN Switch Spanning Treesvlan
Bridge-Domain Switch Spanning Treesbridge-domain
vlan range, Example: 1,3-5,7,9-11vlan-id
Bridge-Domain range, Example: 2,4-5,7,9-11bd-id
Set the bridge priority for the spanning treepriority
bridge priority in increments of 4096prio
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4231
S Commandsspanning-tree vlan priority
Page 4376
spanning-tree vlan rootspanning-tree { vlan <vlan-id> | bridge-domain <bd-id> } root <root-type> [ diameter <diameter-val> [hello-time <hello-time-val> ] ] | no spanning-tree { vlan <vlan-id> | bridge-domain <bd-id> } root [ <root-type>[ diameter <diameter-val> [ hello-time <hello-time-val> ] ] ]
Syntax Description
Negate a command or set its defaultsno
Spanning Tree Subsystemspanning-tree
VLAN Switch Spanning Treesvlan
Bridge-Domain Switch Spanning Treesbridge-domain
vlan range, Example: 1,3-5,7,9-11vlan-id
Bridge-Domain range, Example: 2,4-5,7,9-11bd-id
(Optional) Network diameter of this spanning treediameter
(Optional) Maximum number of bridges between any two end nodesdiameter-val
configure switch as rootroot
configure switch as rootroot-type
(Optional) Set the hello interval for the spanning treehello-time
(Optional) number of seconds between generation of config bpduhello-time-val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4232
S Commandsspanning-tree vlan root
Page 4377
speed-groupspeed-group <gspeed_val> | no speed-group [ <gspeed_val> ]
Syntax Description
Negate a command or set its defaultsno
port group speedspeed-group
Interface port speedgspeed_val
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4233
S Commandsspeed-group
Page 4378
speedspeed { <speed_val> }
Syntax Description
Enter the port speedspeed
Interface port speedspeed_val
Command Mode
• /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4234
S Commandsspeed
Page 4379
speed[no] speed <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set the transmit and receive speedsspeed
Transmit and receive speedsi0
Command Mode
• /exec/configure/com1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4235
S Commandsspeed
Page 4380
speed[no] speed <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set the transmit and receive speedsspeed
Transmit and receive speedsi0
Command Mode
• /exec/configure/console
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4236
S Commandsspeed
Page 4381
speedspeed { <speed_val> }
Syntax Description
Enter the port speedspeed
Interface port speedspeed_val
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel/exec/configure/if-ethernet-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4237
S Commandsspeed
Page 4382
speedspeed { <speed_val> }
Syntax Description
Enter the port speedspeed
Interface port speedspeed_val
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-ethernet-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4238
S Commandsspeed
Page 4383
speedspeed { <speed_val> }
Syntax Description
Enter the port speedspeed
Interface port speedspeed_val
Command Mode
• /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4239
S Commandsspeed
Page 4384
speed[no] speed [ { <speed_val> | auto [ 100 [ 1000 ] ] } ]
Syntax Description
Negate a command or set its defaultsno
Enter the port speedspeed
(Optional) Interface port speedspeed_val
(Optional) auto negotiate speedauto
(Optional) 100 Mbps speed100
(Optional) 1000 Mbps speed1000
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel/exec/configure/if-ethernet-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4240
S Commandsspeed
Page 4385
speed[no] speed [ { <speed_val> | auto [ 100 [ 1000 ] ] } ]
Syntax Description
Negate a command or set its defaultsno
Enter the port speedspeed
(Optional) Interface port speedspeed_val
(Optional) auto negotiate speedauto
(Optional) 100 Mbps speed100
(Optional) 1000 Mbps speed1000
Command Mode
• /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4241
S Commandsspeed
Page 4386
speed autospeed auto
Syntax Description
Enter the port speedspeed
auto negotiate speedauto
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel/exec/configure/if-ethernet-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4242
S Commandsspeed auto
Page 4387
speed auto 100speed auto 100
Syntax Description
Enter the port speedspeed
auto negotiate speedauto
100 Mbps speed100
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel/exec/configure/if-ethernet-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4243
S Commandsspeed auto 100
Page 4388
speed auto 100 1000speed auto 100 1000
Syntax Description
Enter the port speedspeed
auto negotiate speedauto
100 Mbps speed100
1000 Mbps speed1000
Command Mode
• /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4244
S Commandsspeed auto 100 1000
Page 4389
speed auto 100 1000speed auto 100 1000
Syntax Description
Enter the port speedspeed
auto negotiate speedauto
100 Mbps speed100
1000 Mbps speed1000
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel/exec/configure/if-ethernet-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4245
S Commandsspeed auto 100 1000
Page 4390
speed auto 100speed auto 100
Syntax Description
Enter the port speedspeed
auto negotiate speedauto
100 Mbps speed100
Command Mode
• /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4246
S Commandsspeed auto 100
Page 4391
speed autospeed auto
Syntax Description
Enter the port speedspeed
auto negotiate speedauto
Command Mode
• /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4247
S Commandsspeed auto
Page 4392
spf-intervalspf-interval <max-wait> [ <initial-wait> <second-wait> ] | no spf-interval <max-wait> [ <initial-wait><second-wait> ]
Syntax Description
Negate a command or set its defaultsno
Configure SPF intervalspf-interval
Maximum wait between trigger and SPF computation (milli-secs)max-wait
(Optional) Initial wait between trigger and SPF computation (milli-secs)initial-wait
(Optional) Secondwait between trigger and SPF computation (milli-secs)second-wait
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4248
S Commandsspf-interval
Page 4393
spf-intervalspf-interval <level> <max-wait> [ <initial-wait> <second-wait> ] | no spf-interval <level> <max-wait> [<initial-wait> <second-wait> ]
Syntax Description
Negate a command or set its defaultsno
Configure SPF intervalspf-interval
IS-IS levellevel
Maximum wait between trigger and SPF computation (milli-secs)max-wait
(Optional) Initial wait between trigger and SPF computation (milli-secs)initial-wait
(Optional) Secondwait between trigger and SPF computation (milli-secs)second-wait
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4249
S Commandsspf-interval
Page 4394
spf-intervalspf-interval <max-wait> [ <initial-wait> <second-wait> ] | no spf-interval <max-wait> [ <initial-wait><second-wait> ]
Syntax Description
Negate a command or set its defaultsno
Configure SPF intervalspf-interval
Maximum wait between trigger and SPF computation (milli-secs)max-wait
(Optional) Initial wait between trigger and SPF computation (milli-secs)initial-wait
(Optional) Secondwait between trigger and SPF computation (milli-secs)second-wait
Command Mode
• /exec/configure/otv-isis/otv-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4250
S Commandsspf-interval
Page 4395
spf mode incremental[no] spf mode incremental
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure route computation related settingsspf
Set the mode of spf computationmode
If possible, recompute only parts of the SPTincremental
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4251
S Commandsspf mode incremental
Page 4396
sport{ sport <sval> } | { no sport }
Syntax Description
Negate a command or set its defaultsno
Configure ngoam Udp source port rangesport
Udp source port range, max span 1024, Example: 2000-3000,400,500sval
Command Mode
• /exec/configure/configngoamprofile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4252
S Commandssport
Page 4397
sport{ sport <sval> | no sport }
Syntax Description
Negate a command or set its defaultsno
Outer UDP source portsport
Source portsval
Command Mode
• /exec/configure/configngoamconnectcheck
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4253
S Commandssport
Page 4398
src-intf{ src-intf <src_if> }
Syntax Description
Interface on which the host with src ip of the payload is connectedsrc-intf
Interfacesrc_if
Command Mode
• /exec/configure/configngoamccpayload
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4254
S Commandssrc-intf
Page 4399
ssh{ ssh <s0> [ [ [ vrf { <vrf-name> | <vrf-known-name> } ] [ source-ip <s1> ] ] | [ source-interface <intf> ] ] }| { ssh <s0> [ [ [ source-ip <s1> ] [ vrf { <vrf-name> | <vrf-known-name> } ] ] | [ source-interface <intf> ] ]}
Syntax Description
SSH to another systemssh
(Optional) Display per-VRF informationvrf
(Optional) ip address to bindsource-ip
(Optional) Select source interfacesource-interface
Enter hostname or user@hostnames0
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Enter source ip address to binds1
(Optional)intf
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4255
S Commandsssh
Page 4400
ssh6{ ssh6 <s0> [ [ [ vrf { <vrf-name> | <vrf-known-name> } ] [ source-ip <s2> ] [ interface <s1> ] ] | [source-interface <intf> ] ] } | { ssh6 <s0> [ [ [ source-ip <s2> ] [ vrf { <vrf-name> | <vrf-known-name> } ] [interface <s1> ] ] | [ source-interface <intf> ] ] }
Syntax Description
SSH to another system using IPv6 addressingssh6
(Optional) vrf to usevrf
(Optional) ip address to bindsource-ip
(Optional) Select source interfacesource-interface
(Optional) interface to bindinterface
Enter hostname or user@hostnames0
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Enter source ip address to binds2
(Optional) Enter interface to binds1
(Optional)intf
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4256
S Commandsssh6
Page 4401
ssh all[no] ssh { kexalgos | ciphers | macs | keytypes } all
Syntax Description
(Optional) Negate a command or set its defaultsno
SSH to another systemssh
key exchange methods that are used to generate per-connection keyskexalgos
ciphers to encrypt the connectionciphers
message authentication codes used to detect traffic modificationmacs
public key algorithms that the server can use to authenticate itself to theclient
keytypes
enable algorithms supported in current version of SSHall
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4257
S Commandsssh all
Page 4402
ssh cipher-mode weak{ { ssh cipher-mode weak } | { no ssh cipher-mode [ weak ] } }
Syntax Description
Negate a command or set its defaultsno
SSH to another systemssh
Set Cipher-mode for sshcipher-mode
Enable Weak Ciphersweak
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4258
S Commandsssh cipher-mode weak
Page 4403
ssh idle{ ssh { idle-timeout <i0> } [ keepalive-count <i1> ] | no ssh idle-timeout }
Syntax Description
Negate a command or set its defaultsno
SSH to another systemssh
SSH Client session idle timeout valueidle-timeout
Idle timeout value in seconds, 0 to disable, default is 0i0
(Optional) Maximum count of SSH Keepalive packets to be sent to thessh client
keepalive-count
(Optional) Count of SSH Keepalive packets sent to client, default is 0i1
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4259
S Commandsssh idle
Page 4404
ssh key{ ssh key { dsa [ force ] | rsa [ { <i0> | <oldrange> } [ force ] ] | ecdsa { <i0> } [ force ] } | no ssh key [ { dsa[ force ] | rsa [ { <i0> | <oldrange> } [ force ] ] | ecdsa [ { <i0> } [ force ] ] } ] }
Syntax Description
Negate a command or set its defaultsno
SSH to another systemssh
Generate SSH Keykey
Generate DSA keysdsa
(Optional) Force the generation of keys even if previous ones are presentforce
Generate RSA keysrsa
(Optional) Enter number of bits (in multiples of 8)i0
(Optional) Enter number of bitsoldrange
(Optional) Force the generation of keys even if previous ones are presentforce
Generate ECDSA keysecdsa
Enter key size in bits (256, 384 or 521)i0
(Optional) Force the generation of keys even if previous ones are presentforce
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4260
S Commandsssh key
Page 4405
ssh login-attempts{ { ssh login-attempts <d0> } | { no ssh login-attempts [ <d0> ] } }
Syntax Description
Negate a command or set its defaultsno
SSH to another systemssh
Set maximum login attempts from sshlogin-attempts
Specify max-attempt numberd0
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4261
S Commandsssh login-attempts
Page 4406
ssh login-gracetime{ { ssh login-gracetime <d0> } | { no ssh login-gracetime [ <d0> ] } }
Syntax Description
Negate a command or set its defaultsno
SSH to another systemssh
Set login gracetime for ssh connectionlogin-gracetime
Specify grace time in secondsd0
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4262
S Commandsssh login-gracetime
Page 4407
ssh port{ ssh port { <port_number> } | no ssh port }
Syntax Description
Negate a command or set its defaultsno
SSH to another systemssh
Set port number for sshport
Specify port numberport_number
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4263
S Commandsssh port
Page 4408
ssh rekey max-data max-time[no] ssh rekey max-data <data> max-time <time>
Syntax Description
(Optional) Negate a command or set its defaultsno
SSH to another systemssh
Renegotiate ssh keyrekey
data units are Kilo(K), Mega(M) and Giga(G)max-data
Max data transmitted before key renegotiationdata
time units are Seconds(S), Minutes(M) and Hours(H)max-time
Max time lapsed before key renegotiationtime
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4264
S Commandsssh rekey max-data max-time
Page 4409
ssh server enable[no] ssh server enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure SSH parametersssh
Configure SSH Server parametersserver
Enable SSH serverenable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4265
S Commandsssh server enable
Page 4410
ssx exporter[no] ssx exporter <exportername>
Syntax Description
change ssx settingsssx
ssx Exporter to be configuredexporter
ssx Exporter to be configuredexportername
Command Mode
• /exec/configure/config-ssx
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4266
S Commandsssx exporter
Page 4411
ssx monitor[no] ssx monitor <monitorname>
Syntax Description
change ssx settingsssx
ssx Monitor to be configuredmonitor
ssx Monitor to be configuredmonitorname
Command Mode
• /exec/configure/config-ssx
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4267
S Commandsssx monitor
Page 4412
ssx record[no] ssx record <recordname>
Syntax Description
change ssx settingsssx
ssx Record to be configuredrecord
ssx Record to be configuredrecordname
Command Mode
• /exec/configure/config-ssx
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4268
S Commandsssx record
Page 4413
ssx system monitor[no] ssx system monitor <monitorname>
Syntax Description
change ssx settingsssx
global configsystem
ssx Monitor to be appliedmonitor
ssx Monitor to be appliedmonitorname
Command Mode
• /exec/configure/config-ssx
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4269
S Commandsssx system monitor
Page 4414
ssx system system-id[no] ssx system system-id <systemid>
Syntax Description
change ssx settingsssx
global configsystem
ssx system-id to be appliedsystem-id
ssx system-id to be applied, default 0systemid
Command Mode
• /exec/configure/config-ssx
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4270
S Commandsssx system system-id
Page 4415
standby[no] standby [ ip <ip-addr-first> | IPv6 <ip-addrv6-first> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Standby nodestandby
(Optional) ip address for standby nodeip
(Optional) ITD node IPv4 addressip-addr-first
(Optional) IPv6 addressIPv6
Command Mode
• /exec/configure/itd-dg-node
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4271
S Commandsstandby
Page 4416
standby ip[no] standby { ip <ip-addr-first> | IPv6 <ip-addrv6-first> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure standby node for a primary nodestandby
Standby node IPv4 addressip
IP4 prefix in format i.i.i.iip-addr-first
Standby node IPv6 addressIPv6
Command Mode
• /exec/configure/plb-dg-node
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4272
S Commandsstandby ip
Page 4417
start-threshold[no] start-threshold <start-threshold-rate>
Syntax Description
(Optional) Negate the commandno
Configure Start-threshold parameters in bytesstart-threshold
Specify start threshold-ratestart-threshold-rate
Command Mode
• /exec/configure/pkt-drop/profile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4273
S Commandsstart-threshold
Page 4418
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamns/outsel5
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4274
S Commandsstart
Page 4419
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamtah/insel6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4275
S Commandsstart
Page 4420
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamtah/insel7
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4276
S Commandsstart
Page 4421
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamtah/insel8
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4277
S Commandsstart
Page 4422
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamtah/insel9
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4278
S Commandsstart
Page 4423
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamtah/insel10
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4279
S Commandsstart
Page 4424
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamtah/insel19
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4280
S Commandsstart
Page 4425
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamtah/outsel0
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4281
S Commandsstart
Page 4426
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamtah/outsel1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4282
S Commandsstart
Page 4427
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamtah/outsel2
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4283
S Commandsstart
Page 4428
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamns/sel3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4284
S Commandsstart
Page 4429
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamns/sel4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4285
S Commandsstart
Page 4430
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamns/sel5
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4286
S Commandsstart
Page 4431
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamns/sel6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4287
S Commandsstart
Page 4432
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamns/sel7
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4288
S Commandsstart
Page 4433
startstart
Syntax Description
Start Triggerstart
Command Mode
• /exec/elamns/outsel0
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4289
S Commandsstart
Page 4434
statestate <vstate> | no state
Syntax Description
Negate a command or set its defaultsno
Operational state of the VLANstate
vstate
Command Mode
• /exec/configure/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4290
S Commandsstate
Page 4435
state enabled[no] state enabled
Syntax Description
(Optional) Negate a command or set its defaultsno
Port-profile statestate
Enable/ disable the port-profileenabled
Command Mode
• /exec/configure/port-profile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4291
S Commandsstate enabled
Page 4436
statistics[no] statistics
Syntax Description
(Optional) Negate a command or set its defaultsno
Command Mode
• /exec/configure/ipv6acl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4292
S Commandsstatistics
Page 4437
statistics[no] statistics
Syntax Description
(Optional) Negate a command or set its defaultsno
Command Mode
• /exec/configure/ipacl /exec/configure/vacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4293
S Commandsstatistics
Page 4438
statistics[no] statistics
Syntax Description
(Optional) Negate a command or set its defaultsno
Command Mode
• /exec/configure/macacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4294
S Commandsstatistics
Page 4439
statistics collection-intervalstatistics collection-interval <interval-val> | no statistics collection-interval
Syntax Description
Negate a command or set its defaultsno
Statistics related commandsstatistics
How often to retrieve statisticscollection-interval
Collection interval in seconds (0 = do not collect)interval-val
Command Mode
• /exec/configure/openflow/switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4295
S Commandsstatistics collection-interval
Page 4440
statistics per-entry[no] statistics per-entry
Syntax Description
(Optional) Negate a command or set its defaultsno
Command Mode
• /exec/configure/ipv6acl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4296
S Commandsstatistics per-entry
Page 4441
statistics per-entry[no] statistics per-entry
Syntax Description
(Optional) Negate a command or set its defaultsno
Command Mode
• /exec/configure/ipacl /exec/configure/vacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4297
S Commandsstatistics per-entry
Page 4442
statistics per-entry[no] statistics per-entry
Syntax Description
(Optional) Negate a command or set its defaultsno
Command Mode
• /exec/configure/mplsacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4298
S Commandsstatistics per-entry
Page 4443
statistics per-entry[no] statistics per-entry
Syntax Description
(Optional) Negate a command or set its defaultsno
Command Mode
• /exec/configure/macacl
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4299
S Commandsstatistics per-entry
Page 4444
stats-reporting-periodstats-reporting-period <time-in-sec> | no stats-reporting-period
Syntax Description
Negate a command or set its defaultsno
Interval after which statistics are sent to the BMP serverstats-reporting-period
Delay valuetime-in-sec
Command Mode
• /exec/configure/router-bgp/router-bgp-bmp-server
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4300
S Commandsstats-reporting-period
Page 4445
statusstatus
Syntax Description
Status of Triggerstatus
Command Mode
• /exec/elamns/outsel5
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4301
S Commandsstatus
Page 4446
statusstatus
Syntax Description
Status of Triggerstatus
Command Mode
• /exec/elamns/sel3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4302
S Commandsstatus
Page 4447
statusstatus
Syntax Description
Status of Triggerstatus
Command Mode
• /exec/elamns/sel4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4303
S Commandsstatus
Page 4448
statusstatus
Syntax Description
Status of Triggerstatus
Command Mode
• /exec/elamns/sel5
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4304
S Commandsstatus
Page 4449
statusstatus
Syntax Description
Status of Triggerstatus
Command Mode
• /exec/elamns/sel6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4305
S Commandsstatus
Page 4450
statusstatus
Syntax Description
Status of Triggerstatus
Command Mode
• /exec/elamns/sel7
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4306
S Commandsstatus
Page 4451
statusstatus
Syntax Description
Status of Triggerstatus
Command Mode
• /exec/elamns/outsel0
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4307
S Commandsstatus
Page 4452
stop-threshold[no] stop-threshold <stop-threshold-rate>
Syntax Description
(Optional) Negate the commandno
Configure Stop-threshold parameters in bytesstop-threshold
stop-threshold-rate
Command Mode
• /exec/configure/pkt-drop/profile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4308
S Commandsstop-threshold
Page 4453
stopbits[no] stopbits <stopbits-value>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set async line stopbitsstopbits
async line stopbits valuestopbits-value
Command Mode
• /exec/configure/console
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4309
S Commandsstopbits
Page 4454
stopbits 1[no] stopbits { 1 | 2 }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set async line stopbitsstopbits
One stop bit1
Two stop bits2
Command Mode
• /exec/configure/com1
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4310
S Commandsstopbits 1
Page 4455
storm-control-cpustorm-control-cpu { { arp rate } <pps> } | no storm-control-cpu arp
Syntax Description
Negate a command or set its defaultsno
Configure Interface storm control cpustorm-control-cpu
arp storm controlarp
Set allowed arp traffic rate on this interfacerate
value in packets per secpps
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-non-member /exec/configure/if-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4311
S Commandsstorm-control-cpu
Page 4456
storm-controlstorm-control { { { broadcast blevel | multicast mlevel | unicast ulevel | port plevel } { pps <pps_val> | <level>} } | action { shutdown | trap } } | no storm-control { { { broadcast blevel | multicast mlevel | unicast ulevel |port plevel } { pps [ <pps_val> ] | [ <level> ] } } | action [ shutdown | trap ] }
Syntax Description
Negate a command or set its defaultsno
Configure Interface storm controlstorm-control
Broadcast address storm controlbroadcast
Multicast address storm controlmulticast
Unicast address storm controlunicast
Port level storm controlport
Set allowed broadcast traffic level on this interfaceblevel
Set allowed multicast traffic level on this interfacemlevel
Set allowed unicast traffic level on this interfaceulevel
Set allowed Port traffic level on this interfaceplevel
Enter the storm suppression levellevel
Storm-control level is specified in packets per secondpps
Enter the storm suppression level in ppspps_val
Action on storm controlaction
Shutdown (Err-Disable) portshutdown
Generate SNMP traptrap
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-l2-non-member/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4312
S Commandsstorm-control
Page 4457
streetaddress{ streetaddress <line> | no streetaddress }
Syntax Description
Negate a command or set its defaultsno
Configure replacement part shipping address.streetaddress
Provide street address (white spaces are fine)line
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4313
S Commandsstreetaddress
Page 4458
stub{ { [ eigrp ] stub [ { [ direct | connected | static | summary ] [ redistributed ] } + [ leak-map <leak-map> ] | {receive-only } ] } | { no [ eigrp ] stub [ { [ direct | connected | static | summary ] [ redistributed ] } + [ leak-map<leak-map> ] | { receive-only } ] } }
Syntax Description
Negate a command or set its defaultsno
(Optional) EIGRP router configuration commandseigrp
Set IP-EIGRP as stubbed routerstub
(Optional) Do advertise connected routesdirect
(Optional) Do advertise connected routesconnected
(Optional) Do advertise static routesstatic
(Optional) Do advertise summary routessummary
(Optional) Do advertise redistributed routesredistributed
(Optional) Allow dynamic prefixes based on the leak-mapleak-map
(Optional) leak-map nameleak-map
(Optional) Set IP-EIGRP as receive only neighborreceive-only
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4314
S Commandsstub
Page 4459
sub-switch vlansub-switch <subswitch-id> vlan <vlan-id> | no sub-switch <subswitch-id>
Syntax Description
Negate a command or set its defaultsno
Logical sub-switch idsub-switch
Logical subswitch-id(2 to 10)subswitch-id
VLAN-id or VLAN-rangevlan
VLAN-id or VLAN-rangevlan-id
Command Mode
• /exec/configure/openflow/switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4315
S Commandssub-switch vlan
Page 4460
subscription[no] subscription <sub-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Create a Subscriptionsubscription
Identifiersub-id
Command Mode
• /exec/configure/telemetry
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4316
S Commandssubscription
Page 4461
summary-addresssummary-address { <ip-addr> <ip-mask> | <ip-prefix> } <level> | no summary-address { <ip-addr> <ip-mask>| <ip-prefix> } [ <level> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP address summariessummary-address
IP summary addressip-addr
IP summary maskip-mask
IP summary prefixip-prefix
Level to summarize intolevel
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common /exec/configure/router-isis/router-isis-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4317
S Commandssummary-address
Page 4462
summary-addresssummary-address <ipv6-prefix> <level> | no summary-address <ipv6-prefix> [ <level> ]
Syntax Description
Negate a command or set its defaultsno
Configure IP address summariessummary-address
Level to summarize intolevel
Command Mode
• /exec/configure/router-isis/router-isis-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4318
S Commandssummary-address
Page 4463
summary-address[no] summary-address <ipv6-prefix> [ tag <tagval> | not-advertise ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure route summarization for redistributionsummary-address
(Optional) 32-bit tag valuetag
(Optional) 32-bit tag valuetagval
(Optional) Supress advertising the specified summarynot-advertise
Command Mode
• /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4319
S Commandssummary-address
Page 4464
summary-address[no] summary-address { <ip-dest> <ip-mask> | <ip-prefix> } [ tag <tagval> | not-advertise ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure route summarization for redistributionsummary-address
IP prefix format: i.i.i.iip-dest
IP network mask format: m.m.m.mip-mask
IP prefix format: x.x.x.x/mlip-prefix
(Optional) 32-bit tag valuetag
(Optional) 32-bit tag valuetagval
(Optional) Supress advertising the specified summarynot-advertise
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4320
S Commandssummary-address
Page 4465
suppress-arp[no] suppress-arp [ disable ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable ARP suppressionsuppress-arp
(Optional) Override the global ARP suppression configdisable
Command Mode
• /exec/configure/if-nve/vni
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4321
S Commandssuppress-arp
Page 4466
suppress-fib-pending[no] suppress-fib-pending
Syntax Description
(Optional) Negate a command or set its defaultsno
Advertise only routes that are programmed in hardware to peerssuppress-fib-pending
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4322
S Commandssuppress-fib-pending
Page 4467
suppress-fib-pending[no] suppress-fib-pending
Syntax Description
(Optional) Negate a command or set its defaultsno
Advertise only routes that are programmed in hardware to peerssuppress-fib-pending
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4323
S Commandssuppress-fib-pending
Page 4468
suppress-inactive[ no | default ] suppress-inactive
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Advertise only active routes to peersuppress-inactive
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4324
S Commandssuppress-inactive
Page 4469
suppress-inactive[no] suppress-inactive
Syntax Description
(Optional) Negate a command or set its defaultsno
Advertise only active routes to peerssuppress-inactive
Command Mode
• /exec/configure/router-bgp/router-bgp-af
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4325
S Commandssuppress-inactive
Page 4470
suppress-signaling-protocol ldp[ no | default ] suppress-signaling-protocol ldp
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
Suppress VPLS BGP AD protocolsuppress-signaling-protocol
LDP signalingldp
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-l2vpn-vpls
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4326
S Commandssuppress-signaling-protocol ldp
Page 4471
suppress mac-route[no] suppress mac-route
Syntax Description
(Optional) Negate a command or set its defaultsno
Suppress MAC only route advertisementsuppress
MAC routemac-route
Command Mode
• /exec/configure/if-nve
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4327
S Commandssuppress mac-route
Page 4472
switch-idswitch-id <asid> | no switch-id
Syntax Description
Negate a command or set its defaultsno
Configure Switch IDswitch-id
Anycast Switch IDasid
Command Mode
• /exec/configure/anycast
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4328
S Commandsswitch-id
Page 4473
switch-priority{ switch-priority <i0> | no switch-priority }
Syntax Description
Negate a command or set its defaultsno
Priority of the switch(0-highest 7-lowest)switch-priority
Priority of the switch(0-highest 7-lowest)i0
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4329
S Commandsswitch-priority
Page 4474
switch-profileswitch-profile <s0>
Syntax Description
Enter switch-profile configuration modeswitch-profile
Enter the name of the switch-profiles0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4330
S Commandsswitch-profile
Page 4475
switch-profile[no] switch-profile <s0> { profile-only { local | all } | local-config | all-config }
Syntax Description
Negate a command or set its defaultsno
Enter switch-profile configuration modeswitch-profile
Enter the name of the switch-profiles0
Deletion of profile only and no other configurationprofile-only
Deletion of profile only and no other configurations in local switchlocal
Deletion of profile only and no other configurations from all the peersall
Deletion of profile and local configurationlocal-config
Deletion of profile, local and peer configurationsall-config
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4331
S Commandsswitch-profile
Page 4476
switch-role border-leaf[no] switch-role border-leaf
Syntax Description
Switch Roleswitch-role
Border Leafborder-leaf
Command Mode
• /exec/configure/nbm-controller
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4332
S Commandsswitch-role border-leaf
Page 4477
switch-scope controller{ switch-scope controller <controller-id> | no switch-scope controller }
Syntax Description
Negate a command or set its defaultsno
switch-scopeswitch-scope
Controller commandcontroller
Controller idcontroller-id
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4333
S Commandsswitch-scope controller
Page 4478
switch pipelineswitch <switch-id> pipeline <pipeline-id> | no switch <switch-id>
Syntax Description
Negate a command or set its defaultsno
Switchswitch
Logical switch-idswitch-id
Select forwarding profile, use 'show openflow hardware capabilities'for choices
pipeline
Pipeline idpipeline-id
Command Mode
• /exec/configure/openflow
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4334
S Commandsswitch pipeline
Page 4479
switchbackswitchback
Syntax Description
switchback to default vdcswitchback
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4335
S Commandsswitchback
Page 4480
switching-mode fabric-speed 40g[no] switching-mode fabric-speed 40g
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure the operating switching-mode of asicsswitching-mode
fabric speed settingsfabric-speed
fabric speed at 40g instead of 42g40g
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4336
S Commandsswitching-mode fabric-speed 40g
Page 4481
switching-mode fast-to-slow-speed-cut-through[no] switching-mode fast-to-slow-speed-cut-through
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure the operating switching-mode of asicsswitching-mode
Operate in fast-to-slow speed cut-through modefast-to-slow-speed-cut-through
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4337
S Commandsswitching-mode fast-to-slow-speed-cut-through
Page 4482
switching-mode store-forward[no] switching-mode store-forward
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure the operating switching-mode of asicsswitching-mode
Operate in store and forward modestore-forward
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4338
S Commandsswitching-mode store-forward
Page 4483
switchport[no] switchport
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-eth-non-member /exec/configure/if-ethernet/exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-port-channel/exec/configure/if-ethernet-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4339
S Commandsswitchport
Page 4484
switchportswitchport
Syntax Description
Configure switchport parametersswitchport
Command Mode
• /exec/configure/if-eth-non-member /exec/configure/if-ethernet-all /exec/configure/if-port-channel/exec/configure/if-ethernet-p2p
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4340
S Commandsswitchport
Page 4485
switchport access vlanswitchport access vlan <vlan-id-access> | no switchport access vlan
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set access mode characteristics of the interfaceaccess
Set VLAN when interface is in access modevlan
VLAN ID of the VLAN when this port is in access modevlan-id-access
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-p2p-switch/exec/configure/if-remote-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4341
S Commandsswitchport access vlan
Page 4486
switchport access vlanswitchport access vlan <vlan-id-access> | no switchport access vlan
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set access mode characteristics of the interfaceaccess
Set VLAN when interface is in access modevlan
VLAN ID of the VLAN when this port is in access modevlan-id-access
Command Mode
• /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4342
S Commandsswitchport access vlan
Page 4487
switchport access vlanswitchport access vlan <vlan-id-access> | no switchport access vlan
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set access mode characteristics of the interfaceaccess
Set VLAN when interface is in access modevlan
VLAN ID of the VLAN when this port is in access modevlan-id-access
Command Mode
• /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4343
S Commandsswitchport access vlan
Page 4488
switchport autostate excludeswitchport autostate exclude [ vlan { <exclude-vlans> | add <add-vlans> | except <except-vlans> | remove<remove-vlans> | all | none } ] | no switchport autostate exclude [ dummy ] [ vlan { <exclude-vlans> | add<add-vlans> } ]
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Include or exclude this port from vlan link up calculationautostate
Exclude this port from vlan link up calculationexclude
(Optional) VLAN Idvlan
(Optional) VLAN IDs of the VLANs to auto-state exclude on thisinterface
exclude-vlans
(Optional) add VLANs to except listadd
(Optional) VLAN IDs of the VLANs to auto-state exclude on thisinterface
add-vlans
(Optional) List of VLANs to excepted from auto-state excludeexcept
(Optional) VLAN IDs of the VLANs to auto-state exclude on thisinterface
except-vlans
(Optional) remove VLANs from except listremove
(Optional) VLAN IDs of the VLANs to auto-state exclude on thisinterface
remove-vlans
(Optional) Exclude all VLANsall
(Optional) Exclude no VLANsnone
(Optional) Hidden Keyworddummy
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-gig-ether/exec/configure/if-port-channel-range /exec/configure/if-eth-port-channel-switch/exec/configure/if-remote-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4344
S Commandsswitchport autostate exclude
Page 4489
switchport backup interface[no] switchport backup interface <if0> [ __readonly__ <from_snmp> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set backup for the interfacebackup
Specify an interface as backupinterface
Enter interface nameif0
(Optional) Read Only__readonly__
(Optional) Configuration comes from SNMPfrom_snmp
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4345
S Commandsswitchport backup interface
Page 4490
switchport backup interface[no] switchport backup interface <if0> [ __readonly__ <from_snmp> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set backup for the interfacebackup
Specify an interface as backupinterface
Enter interface nameif0
(Optional) Read Only__readonly__
(Optional) Configuration comes from SNMPfrom_snmp
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4346
S Commandsswitchport backup interface
Page 4491
switchport backup interface multicast fast-convergence[no] switchport backup interface <if0> multicast fast-convergence
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set backup for the interfacebackup
Specify an interface as backupinterface
Enter interface nameif0
multicast parametersmulticast
configure fast convergence on backup interfacefast-convergence
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4347
S Commandsswitchport backup interface multicast fast-convergence
Page 4492
switchport backup interface multicast fast-convergence[no] switchport backup interface <if0> multicast fast-convergence
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set backup for the interfacebackup
Specify an interface as backupinterface
Enter interface nameif0
multicast parametersmulticast
configure fast convergence on backup interfacefast-convergence
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4348
S Commandsswitchport backup interface multicast fast-convergence
Page 4493
switchport backup interface preemption delay{ switchport backup interface <if0> preemption delay <delay_secs> } | { no switchport backup interface <if0>preemption delay }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set backup for the interfacebackup
Specify an interface as backupinterface
Enter interface nameif0
preemption parameterspreemption
preemption parametersdelay
delaypreemption
preemption delay in secondsdelay_secs
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4349
S Commandsswitchport backup interface preemption delay
Page 4494
switchport backup interface preemption delay{ switchport backup interface <if0> preemption delay <delay_secs> } | { no switchport backup interface <if0>preemption delay }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set backup for the interfacebackup
Specify an interface as backupinterface
Enter interface nameif0
preemption parameterspreemption
preemption parametersdelay
delaypreemption
preemption delay in secondsdelay_secs
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4350
S Commandsswitchport backup interface preemption delay
Page 4495
switchport backup interface preemption mode{ switchport backup interface <if0> preemption mode <preempt_mode> } | { no switchport backup interface<if0> preemption mode }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set backup for the interfacebackup
Specify an interface as backupinterface
Enter interface nameif0
preemption parameterspreemption
set the preemption modemode
modepreemption
preemption modepreempt_mode
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4351
S Commandsswitchport backup interface preemption mode
Page 4496
switchport backup interface preemption mode{ switchport backup interface <if0> preemption mode <preempt_mode> } | { no switchport backup interface<if0> preemption mode }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set backup for the interfacebackup
Specify an interface as backupinterface
Enter interface nameif0
preemption parameterspreemption
set the preemption modemode
modepreemption
preemption modepreempt_mode
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4352
S Commandsswitchport backup interface preemption mode
Page 4497
switchport beacon[no] switchport beacon
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Disable/enable the beacon for an interfacebeacon
Command Mode
• /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext /exec/configure/if-legacy-eth
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4353
S Commandsswitchport beacon
Page 4498
switchport block unicastswitchport block { unicast | multicast } | no switchport block { unicast | multicast }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Block specified outbound traffic for all VLANsblock
Block unknown unicast trafficunicast
Block flood multicast trafficmulticast
Command Mode
• /exec/configure/if-eth-l2-non-member /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4354
S Commandsswitchport block unicast
Page 4499
switchport descriptionswitchport description <desc_line> | no switchport description [ <desc_line> ]
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enter description of maximum 254 charactersdescription
Description of maximum 254 charactersdesc_line
Command Mode
• /exec/configure/if-iscsi /exec/configure/if-fcip /exec/configure/if-fc /exec/configure/if-bay/exec/configure/if-ext /exec/configure/if-gig-ether /exec/configure/if-fa /exec/configure/if-fv/exec/configure/if-san-port-channel /exec/configure/if-sme /exec/configure/if-ioa/exec/configure/if-gig-ether-sub /exec/configure/if-vfc /exec/configure/if-vfc-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4355
S Commandsswitchport description
Page 4500
switchport dot1q ethertypeswitchport dot1q ethertype { 0x8100 | 0x88A8 | 0x9100 | <any> } | no switchport dot1q ethertype [ <any> ]
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Configure dot1q EtherType valuedot1q
Configure dot1q EtherType valueethertype
Default EtherType for 802.1q frames0x8100
EtherType for 802.1ad double tagged frames0x88A8
EtherType for QinQ frames0x9100
Any EtherTypeany
Command Mode
• /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4356
S Commandsswitchport dot1q ethertype
Page 4501
switchport dot1q ethertypeswitchport dot1q ethertype { 0x8100 | 0x88A8 | 0x9100 | <any> } | no switchport dot1q ethertype [ <any> ]
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Configure dot1q EtherType valuedot1q
Configure dot1q EtherType valueethertype
Default EtherType for 802.1q frames0x8100
EtherType for 802.1ad double tagged frames0x88A8
EtherType for QinQ frames0x9100
Any EtherTypeany
Command Mode
• /exec/configure/if-eth-l2-non-member /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4357
S Commandsswitchport dot1q ethertype
Page 4502
switchport duplex{ switchport duplex { auto | full | half } | no switchport duplex [ { auto | full | half } ] }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enter the port duplex modeduplex
auto negotiate duplex modeauto
full duplex modefull
half duplex modehalf
Command Mode
• /exec/configure/if-legacy-eth /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4358
S Commandsswitchport duplex
Page 4503
switchport host[no] switchport host
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set port hosthost
Command Mode
• /exec/configure/if-eth-l2-non-member /exec/configure/if-ethernet-switch/exec/configure/if-ethernet-switch-m /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4359
S Commandsswitchport host
Page 4504
switchport ignore bit-errors{ switchport ignore bit-errors | no switchport ignore bit-errors }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enter parameter to be ignoredignore
ignore bit-errorsbit-errors
Command Mode
• /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4360
S Commandsswitchport ignore bit-errors
Page 4505
switchport isolated[no] switchport isolated
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Disable loop-free detection.isolated
Command Mode
• /exec/configure/if-eth-l2-non-member /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4361
S Commandsswitchport isolated
Page 4506
switchport mac-learn disableswitchport mac-learn disable | no switchport mac-learn disable
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Disable/enable mac learning on interfacemac-learn
Disable mac learning on all VLANs on interfacedisable
Command Mode
• /exec/configure/if-eth-l2-non-member /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4362
S Commandsswitchport mac-learn disable
Page 4507
switchport mode{ switchport mode { <port_mode> } | no switchport mode }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enter the port modemode
port modeport_mode
Command Mode
• /exec/configure/if-eth-l2-non-member /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4363
S Commandsswitchport mode
Page 4508
switchport mode{ switchport mode { <port_mode> } | no switchport mode }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enter the port modemode
port modeport_mode
Command Mode
• /exec/configure/if-eth-l2-non-member /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4364
S Commandsswitchport mode
Page 4509
switchport modeswitchport mode <port_mode> | no switchport mode [ <port_mode> ]
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enter the port modemode
Port modeport_mode
Command Mode
• /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4365
S Commandsswitchport mode
Page 4510
switchport modeswitchport mode <port_mode> | no switchport mode [ <port_mode> ]
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enter the port modemode
Port modeport_mode
Command Mode
• /exec/configure/if-fcip
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4366
S Commandsswitchport mode
Page 4511
switchport modeswitchport mode <port_mode> | no switchport mode [ <port_mode> ]
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enter the port modemode
Port modeport_mode
Command Mode
• /exec/configure/if-san-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4367
S Commandsswitchport mode
Page 4512
switchport modeswitchport mode <port_mode> | no switchport mode [ <port_mode> ]
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enter the port modemode
Port modeport_mode
Command Mode
• /exec/configure/if-vfc /exec/configure/if-vfc-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4368
S Commandsswitchport mode
Page 4513
switchport mode monitor buffer-limitswitchport mode monitor buffer-limit { <value> [ packets | bytes | kbytes | mbytes ] } | no switchport modemonitor buffer-limit
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enter the port modemode
Configures an interface as span-destinationmonitor
Set buffer limit for span destinationbuffer-limit
Limit in terms of packetsvalue
(Optional) Packetspackets
(Optional) Bytesbytes
(Optional) Kilo byteskbytes
(Optional) Mega bytesmbytes
Command Mode
• /exec/configure/if-eth-l2-non-member /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4369
S Commandsswitchport mode monitor buffer-limit
Page 4514
switchport mode private-vlan{ switchport mode private-vlan <port_mode> } | { no switchport mode private-vlan [ <port_mode> ] }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enter the port modemode
Set the private VLAN configurationprivate-vlan
private vlan modeport_mode
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-eth-port-channel-switch/exec/configure/if-remote-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4370
S Commandsswitchport mode private-vlan
Page 4515
switchport mode private-vlan trunk{ switchport mode private-vlan trunk <trunk_mode> } | { no switchport mode private-vlan trunk [<trunk_mode> ] }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enter the port modemode
Set the private VLAN configurationprivate-vlan
private-vlan trunktrunk
private vlan trunk modetrunk_mode
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-all /exec/configure/if-eth-port-channel-switch/exec/configure/if-remote-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4371
S Commandsswitchport mode private-vlan trunk
Page 4516
switchport monitorswitchport monitor [ ingress [ learning ] ] | no switchport monitor
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Configures an interface as span-destinationmonitor
(Optional) Enables the forwarding on incoming packetsingress
(Optional) Enables mac-learninglearning
Command Mode
• /exec/configure/if-eth-l2-non-member /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4372
S Commandsswitchport monitor
Page 4517
switchport mtu{ switchport mtu <i0> | no switchport mtu [ <i0> ] }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Configure mtu for the portmtu
Enter mtui0
Command Mode
• /exec/configure/if-gig-ether-sub /exec/configure/if-legacy-eth
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4373
S Commandsswitchport mtu
Page 4518
switchport owner{ switchport owner { <owner_str> } | no switchport owner }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Specify the owner of an interfaceowner
Owner of maximum 80 charactersowner_str
Command Mode
• /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext /exec/configure/if-vfc/exec/configure/if-vfc-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4374
S Commandsswitchport owner
Page 4519
switchport port-security[no] switchport port-security
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Port security related commandport-security
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4375
S Commandsswitchport port-security
Page 4520
switchport port-security aging time[no] switchport port-security aging time <value>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Port security related commandport-security
Port-security aging commandsaging
Port-security aging timetime
Aging time in minutes. Enter a value between 1 and 1440value
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4376
S Commandsswitchport port-security aging time
Page 4521
switchport port-security aging type absolute[no] switchport port-security aging type { absolute | inactivity }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Port security related commandport-security
Port-security aging commandsaging
Type of timerstype
Absolute Timerabsolute
Inactivity Timerinactivity
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4377
S Commandsswitchport port-security aging type absolute
Page 4522
switchport port-security mac-address[no] switchport port-security mac-address <mac-address> [ vlan <vlanid> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Port security related commandport-security
MAC addressmac-address
48 bit mac address format HHHH.HHHH.HHHHmac-address
(Optional) Vlan on which the mac address should be securedvlan
(Optional) vlan id. Enter a value between 1 and 4094vlanid
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4378
S Commandsswitchport port-security mac-address
Page 4523
switchport port-security mac-address sticky[no] switchport port-security mac-address sticky
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Port security related commandport-security
MAC addressmac-address
Sticky MAC addresssticky
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4379
S Commandsswitchport port-security mac-address sticky
Page 4524
switchport port-security maximum[no] switchport port-security maximum <value> [ vlan <vlanid> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Port security related commandport-security
Max secure addressesmaximum
Maximum addresses 1 to 1025value
(Optional) Vlan on which the mac address should be securedvlan
(Optional) vlan id. Enter a value between 1 and 4094vlanid
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4380
S Commandsswitchport port-security maximum
Page 4525
switchport port-security violation[no] switchport port-security violation { protect | restrict | shutdown }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Port security related commandport-security
Security violation modeviolation
security violation protect modeprotect
security violation restrict moderestrict
security violation shutdown modeshutdown
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4381
S Commandsswitchport port-security violation
Page 4526
switchport priority extend cos{ switchport priority extend { cos <cos-value> | trust } | no switchport priority extend }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
CoS Priority parameterpriority
Enter priority extend modeextend
Switch will send CDP packet to instruct phone to mark data traffic withCoS value
cos
Trust CoS value to be sent to the IP Phonecos-value
Switch will send CDP packet to instruct phone to trust tagged data traffictrust
Command Mode
• /exec/configure/if-eth-l2-non-member /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4382
S Commandsswitchport priority extend cos
Page 4527
switchport private-vlan association trunk{ switchport private-vlan association trunk <primary-vlan> <secondary-vlan> } | { no switchport private-vlanassociation trunk [ <primary-vlan> [ <secondary-vlan> ] ] }
Syntax Description
Configure switchport parametersswitchport
Set the private VLAN configurationprivate-vlan
private vlan trunk associationassociation
private-vlan trunk secondarytrunk
Negate a command or set its defaultsno
Primary VLAN IDprimary-vlan
Secondary VLAN IDsecondary-vlan
Command Mode
• /exec/configure/if-switching /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4383
S Commandsswitchport private-vlan association trunk
Page 4528
switchport private-vlan host-association{ switchport private-vlan host-association <primary-vlan> <secondary-vlan> } | { no switchport private-vlanhost-association }
Syntax Description
Configure switchport parametersswitchport
Set the private VLAN configurationprivate-vlan
Set the private VLAN host associationhost-association
Negate a command or set its defaultsno
Primary VLAN IDprimary-vlan
Secondary VLAN IDsecondary-vlan
Command Mode
• /exec/configure/if-switching /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4384
S Commandsswitchport private-vlan host-association
Page 4529
switchport private-vlan mapping{ switchport private-vlan mapping <primary-vlan> [ { add | remove } ] <secondary_vlans> } | { no switchportprivate-vlan mapping [ <primary-vlan> <secondary_vlans> ] }
Syntax Description
Configure switchport parametersswitchport
Set the private VLAN configurationprivate-vlan
Set the private VLAN access/trunk promiscuous mappingmapping
(Optional) Add a VLAN to private VLAN listadd
(Optional) Remove a VLAN from private VLAN listremove
Negate a command or set its defaultsno
Primary private VLANprimary-vlan
Secondary VLAN IDssecondary_vlans
Command Mode
• /exec/configure/if-switching /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4385
S Commandsswitchport private-vlan mapping
Page 4530
switchport private-vlan mapping trunk{ switchport private-vlan mapping trunk <primary-vlan> [ { add | remove } ] <secondary_vlans> } | { noswitchport private-vlan mapping trunk [ <primary-vlan> [ <secondary_vlans> ] ] }
Syntax Description
Configure switchport parametersswitchport
Set the private VLAN configurationprivate-vlan
Set the private VLAN access/trunk promiscuous mappingmapping
(Optional) Add a VLAN to private VLAN listadd
(Optional) Remove a VLAN from private VLAN listremove
Negate a command or set its defaultsno
private-vlan trunk promiscuoustrunk
Primary private VLANprimary-vlan
Secondary VLAN IDssecondary_vlans
Command Mode
• /exec/configure/if-switching /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4386
S Commandsswitchport private-vlan mapping trunk
Page 4531
switchport private-vlan trunk allowed vlanswitchport private-vlan trunk allowed vlan { <allowed-vlans> | add <add-vlans> | except <except-vlans> |remove <remove-vlans> | all | none } | no switchport private-vlan trunk allowed vlan <no-allowed-vlans>
Syntax Description
Configure switchport parametersswitchport
Set the private VLAN configurationprivate-vlan
Set the private vlan trunking configurationtrunk
Set allowed VLANs when interface is in private-vlan trunking modeallowed
VLAN statusvlan
VLAN IDs of the allowed VLANs when interface is in private-vlantrunking mode
allowed-vlans
add VLANs to the current listadd
VLAN IDs of the allowed VLANs when interface is in private-vlantrunking mode
add-vlans
all VLANs except the followingexcept
VLAN IDs of disallowed VLANS when this port is in trunking modeexcept-vlans
remove VLANs from the current listremove
VLAN IDs of disallowed VLANS when this port is in trunking moderemove-vlans
all VLANsall
no VLANsnone
Negate a command or set its defaultsno
VLAN IDs of disallowed VLANs when this port is in trunking modeno-allowed-vlans
Command Mode
• /exec/configure/if-switching /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4387
S Commandsswitchport private-vlan trunk allowed vlan
Page 4532
switchport private-vlan trunk native vlan{ switchport private-vlan trunk native vlan <native-vlan> } | { no switchport private-vlan trunk native vlan }
Syntax Description
Configure switchport parametersswitchport
Set the private VLAN configurationprivate-vlan
Negate a command or set its defaultsno
Set the private vlan trunking configurationtrunk
Set the private vlan trunking native configurationnative
VLAN statusvlan
native vlan idnative-vlan
Command Mode
• /exec/configure/if-switching /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4388
S Commandsswitchport private-vlan trunk native vlan
Page 4533
switchport promiscuous-mode offswitchport promiscuous-mode { off | on }
Syntax Description
Configure switchport parametersswitchport
Configure promiscuous mode for the portpromiscuous-mode
Disable promiscuous modeoff
Enable promiscuous modeon
Command Mode
• /exec/configure/if-gig-ether-sub /exec/configure/if-legacy-eth
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4389
S Commandsswitchport promiscuous-mode off
Page 4534
switchport speed{ switchport speed { 1000 | 2000 | 4000 | 8000 | 10000 | 16000 | 32000 | auto [ max { 20001 | 40001 | 80001| 160001 | 320001 } ] } | no switchport speed [ { 1000 | 2000 | 4000 | 8000 | 10000 | 16000 | 32000 | auto [max { 20001 | 40001 | 80001 | 160001 | 320001 } ] } ] }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enter the port speedspeed
1000 Mbps speed1000
2000 Mbps speed2000
4000 Mbps speed4000
8000 Mbps speed8000
10000 Mbps speed10000
16000 Mbps speed16000
32000 Mbps speed32000
auto negotiate speedauto
(Optional) Maximum speedmax
(Optional) Maximum speed is 200020001
(Optional) Maximum speed is 400040001
(Optional) Maximum speed is 800080001
(Optional) Maximum speed is 16000160001
(Optional) Maximum speed is 32000320001
Command Mode
• /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext /exec/configure/if-san-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4390
S Commandsswitchport speed
Page 4535
switchport speed{ switchport speed { 10 | 100 | 1000 | auto } | no switchport speed [ { 10 | 100 | 1000 | auto } ] }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enter the port speedspeed
10 Mbps speed10
100 Mbps speed100
1000 Mbps speed1000
auto negotiate speedauto
Command Mode
• /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4391
S Commandsswitchport speed
Page 4536
switchport trunk allow-multi-tagswitchport trunk allow-multi-tag | no switchport trunk allow-multi-tag
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Configure trunking parameters on an interfacetrunk
Allows Multiple Q-Tagsallow-multi-tag
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-p2p-switch/exec/configure/if-remote-ethernet-switch /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4392
S Commandsswitchport trunk allow-multi-tag
Page 4537
switchport trunk allowed vlanswitchport trunk allowed vlan { <allow-vlans> | add <add-vlans> | except <except-vlans> | remove<remove-vlans> | all | none } | no switchport trunk allowed vlan
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Configure trunking parameters on an interfacetrunk
Set allowed VLAN characteristics when interface is in trunking modeallowed
Set allowed VLANs when interface is in trunking modevlan
VLAN IDs of the allowed VLANs when this port in trunking modeallow-vlans
add VLANs to the current listadd
VLAN IDs of the allowed VLANs when this port in trunking modeadd-vlans
all VLANsall
all VLANs except the followingexcept
VLAN IDs of the allowed VLANs when this port in trunking modeexcept-vlans
no VLANsnone
remove VLANs from the current listremove
VLAN IDs of the allowed VLANs when this port in trunking moderemove-vlans
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-p2p-switch/exec/configure/if-remote-ethernet-switch /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4393
S Commandsswitchport trunk allowed vlan
Page 4538
switchport trunk allowed vsan{ switchport trunk allowed vsan { add <i0> | all | <i1> [ no-warning ] } | no switchport trunk allowed vsan [{ add <i0> | all | <i1> } ] }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Configure trunking parameters on an interfacetrunk
Configure allowed list for interface(s)allowed
Configure allowed list for interface(s)vsan
give VSAN id range to add to allowed vsan listadd
VSAN id rangei0
add all the vsans to allowed vsan listall
VSAN id rangei1
(Optional) Avoid displaying a warning message and user prompt forthis command
no-warning
Command Mode
• /exec/configure/if-fc /exec/configure/if-san-port-channel /exec/configure/if-fcip /exec/configure/if-svc/exec/configure/if-bay /exec/configure/if-ext
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4394
S Commandsswitchport trunk allowed vsan
Page 4539
switchport trunk allowed vsan{ switchport trunk allowed vsan { add <i0> | all | <i1> [ no-warning ] } | no switchport trunk allowed vsan [{ add <i0> | all | <i1> } ] }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Configure trunking parameters on an interfacetrunk
Configure allowed list for interface(s)allowed
Configure allowed list for interface(s)vsan
give VSAN id range to add to allowed vsan listadd
VSAN id rangei0
add all the vsans to allowed vsan listall
VSAN id rangei1
(Optional) Avoid displaying a warning message and user prompt forthis command
no-warning
Command Mode
• /exec/configure/if-vfc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4395
S Commandsswitchport trunk allowed vsan
Page 4540
switchport trunk mode{ switchport trunk mode { <trunk_mode> } | no switchport trunk mode [ { <trunk_mode> } ] }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Configure trunking parameters on an interfacetrunk
Configure trunking modemode
Trunk modetrunk_mode
Command Mode
• /exec/configure/if-fc /exec/configure/if-bay /exec/configure/if-ext /exec/configure/if-fcip/exec/configure/if-san-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4396
S Commandsswitchport trunk mode
Page 4541
switchport trunk mode{ switchport trunk mode { <trunk_mode> } | no switchport trunk mode [ { <trunk_mode> } ] }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Configure trunking parameters on an interfacetrunk
Configure trunking modemode
Trunk modetrunk_mode
Command Mode
• /exec/configure/if-vfc /exec/configure/if-vfc-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4397
S Commandsswitchport trunk mode
Page 4542
switchport trunk native vlanswitchport trunk native vlan <vlan-id-native> | no switchport trunk native vlan
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Configure trunking parameters on an interfacetrunk
Set trunking native characteristics when interface is in trunking modenative
Set native VLAN when interface is in trunking modevlan
VLAN ID of the native VLAN when this port is in trunking modevlan-id-native
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-p2p-switch/exec/configure/if-remote-ethernet-switch /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4398
S Commandsswitchport trunk native vlan
Page 4543
switchport trunk pruning vlan except add remove none all{ no switchport trunk pruning vlan [ <vlan-ids> ] | switchport trunk pruning vlan <vlan-ids> | switchport trunkpruning vlan except <vlan-ids> | switchport trunk pruning vlan add <vlan-ids> | switchport trunk pruning vlanremove <vlan-ids> | switchport trunk pruning vlan none | switchport trunk pruning vlan all }
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Configure trunking parameters on an interfacetrunk
Set pruning VLAN characteristics when interface is in trunking modepruning
Enter VLANsvlan
add VLANs to the current listadd
remove VLANs from the current listremove
all VLANs except the followingexcept
no VLANsnone
all VLANsall
(Optional) Enter VLANsvlan-ids
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4399
S Commandsswitchport trunk pruning vlan except add remove none all
Page 4544
switchport virtual-ethernet-bridgeswitchport virtual-ethernet-bridge | no switchport virtual-ethernet-bridge
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Enable hair-pin forwardingvirtual-ethernet-bridge
Command Mode
• /exec/configure/if-eth-l2-non-member /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4400
S Commandsswitchport virtual-ethernet-bridge
Page 4545
switchport vlan mapping[no] switchport vlan mapping <vlan-id-orig> [ inner <vlan-id-inner> ] <vlan-id-translated>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set VLAN translation mappingvlan
VLAN translation mappingmapping
VLAN ID 1-3967vlan-id-orig
(Optional) inner vlanidinner
(Optional) Inner VLAN IDvlan-id-inner
Translated VLAN IDvlan-id-translated
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-p2p-switch/exec/configure/if-remote-ethernet-switch /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4401
S Commandsswitchport vlan mapping
Page 4546
switchport vlan mapping all[no] switchport vlan mapping all
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set VLAN translation mappingvlan
VLAN translation mappingmapping
all VLANsall
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-p2p-switch/exec/configure/if-remote-ethernet-switch /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4402
S Commandsswitchport vlan mapping all
Page 4547
switchport vlan mapping all dot1q-tunnel[no] switchport vlan mapping all dot1q-tunnel
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set VLAN translation mappingvlan
VLAN translation mappingmapping
all VLANsall
selective dot1q-tunneldot1q-tunnel
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-p2p-switch/exec/configure/if-remote-ethernet-switch /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4403
S Commandsswitchport vlan mapping all dot1q-tunnel
Page 4548
switchport vlan mapping all dot1q-tunnel[no] switchport vlan mapping all dot1q-tunnel <vlan-id-translated>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set VLAN translation mappingvlan
VLAN translation mappingmapping
all VLANsall
selective dot1q-tunneldot1q-tunnel
Translated VLAN IDvlan-id-translated
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-p2p-switch/exec/configure/if-remote-ethernet-switch /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4404
S Commandsswitchport vlan mapping all dot1q-tunnel
Page 4549
switchport vlan mapping dot1q-tunnel[no] switchport vlan mapping <vlan-id-orig2> dot1q-tunnel <vlan-id-translated>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set VLAN translation mappingvlan
VLAN translation mappingmapping
VLAN ID 1-4094 or Vlan range(s): 1-5, 10 or 2-5,7-19 for Selectivedot1q-tunnel
vlan-id-orig2
selective dot1q-tunneldot1q-tunnel
Translated VLAN IDvlan-id-translated
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-p2p-switch/exec/configure/if-remote-ethernet-switch /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4405
S Commandsswitchport vlan mapping dot1q-tunnel
Page 4550
switchport vlan mapping dot1q-tunnel allowed-vlan[no] switchport vlan mapping dot1q-tunnel allowed-vlan <vlan-id-list>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set VLAN translation mappingvlan
VLAN translation mappingmapping
selective dot1q-tunneldot1q-tunnel
Set allowed VLAN characteristics when interface is in trunking modeallowed-vlan
VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19vlan-id-list
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-p2p-switch/exec/configure/if-remote-ethernet-switch /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4406
S Commandsswitchport vlan mapping dot1q-tunnel allowed-vlan
Page 4551
switchport vlan mapping enable[no] switchport vlan mapping enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set VLAN translation mappingvlan
VLAN translation mappingmapping
enable/disable VLAN translationenable
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-p2p-switch/exec/configure/if-remote-ethernet-switch /exec/configure/if-ethernet-all/exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4407
S Commandsswitchport vlan mapping enable
Page 4552
switchport voice vlanswitchport voice vlan { <vlan-id-voice> | dot1p | untagged } | no switchport voice vlan
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set voice mode characterestics of the interfacevoice
Set VLAN for VoIP trafficvlan
VLAN ID of the VLAN configured for VoIP trafficvlan-id-voice
Switch will send CDP packets to instruct IP phone to send voice trafficin 802.1p frames
dot1p
Switch will send CDP packets to instruct IP phone to send voice trafficuntagged
untagged
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-ethernet-p2p-switch/exec/configure/if-remote-ethernet-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4408
S Commandsswitchport voice vlan
Page 4553
switchport voice vlanswitchport voice vlan { <vlan-id-voice> | dot1p | untagged } | no switchport voice vlan
Syntax Description
Negate a command or set its defaultsno
Configure switchport parametersswitchport
Set voice mode characterestics of the interfacevoice
Set VLAN for VoIP trafficvlan
VLAN ID of the VLAN configured for VoIP trafficvlan-id-voice
Switch will send CDP packets to instruct IP phone to send voice trafficin 802.1p frames
dot1p
Switch will send CDP packets to instruct IP phone to send voice trafficuntagged
untagged
Command Mode
• /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4409
S Commandsswitchport voice vlan
Page 4554
switchto vdcswitchto vdc <e-vdc2> [ force ] [ bypass ] [ __readonly__ <vdc_id> <invalid_vdc_id> <noauth_vdc_id><no_first> ]
Syntax Description
Goto specific Virtual Device Context <vdc-name> | <vdc-id>switchto
Manage Virtual Device Contextvdc
Enter Virtual Device Context <vdc-id>e-vdc2
(Optional) Read Only__readonly__
(Optional) forceforce
(Optional) Enter Virtual Device Context <vdc-id>vdc_id
(Optional) Enter Virtual Device Context <vdc-id>invalid_vdc_id
(Optional) Enter Virtual Device Context <vdc-id>noauth_vdc_id
(Optional) Enter Virtual Device Context <vdc-id>no_first
(Optional) Enter Virtual Device Context <vdc-id>bypass
Command Mode
• /exec/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4410
S Commandsswitchto vdc
Page 4555
sync-peers destinationsync-peers destination <dst-ip> [ source <src-ip> | vrf <vrf-name> ] + | no sync-peers destination [ <dst-ip>[ source <src-ip> ] ]
Syntax Description
Negate a command or set its defaultsno
Specify peers to whom configuration needs to be syncedsync-peers
Specify destination ip address of peer switchdestination
IPv4 address (A.B.C.D) of destinationdst-ip
(Optional) Source interface for sending out configssource
(Optional) IPv4 address (A.B.C.D) of sourcesrc-ip
(Optional) vrf to be used default/managementvrf
(Optional) vrf to be usedvrf-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4411
S Commandssync-peers destination
Page 4556
sync-snmp-passwordsync-snmp-password <s0> <s1> <s2>
Syntax Description
sync snmp passwordsync-snmp-password
passwords0
users1
snmp client hosts2
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4412
S Commandssync-snmp-password
Page 4557
sync-snmp-passwordsync-snmp-password <s0>
Syntax Description
sync snmp passwordsync-snmp-password
passwords0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4413
S Commandssync-snmp-password
Page 4558
sync-snmp-password[no] sync-snmp-password <s0>
Syntax Description
(Optional) Negate a command or set its defaultsno
sync snmp passwordsync-snmp-password
passwords0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4414
S Commandssync-snmp-password
Page 4559
system-macsystem-mac <sysmac> | no system-mac
Syntax Description
Negate a command or set its defaultsno
Configure system mac addresssystem-mac
specify system mac addresssysmac
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4415
S Commandssystem-mac
Page 4560
system-mac[no] system-mac <mac-addr>
Syntax Description
(Optional) Negate a command or set its defaultsno
Mac Addresssystem-mac
specify system mac addressmac-addr
Command Mode
• /exec/configure/if-eth-port-channel/ethernet-segment
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4416
S Commandssystem-mac
Page 4561
system-prioritysystem-priority <syspri> | no system-priority <syspri>
Syntax Description
Negate a command or set its defaultsno
Configure system prioritysystem-priority
specify system prioritysyspri
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4417
S Commandssystem-priority
Page 4562
system[no] system { default switchport { mode F | trunk mode1 { auto | off | on } } | delayed-traps { enable mode2FX | timer <i0> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
System configuration commandssystem
Configure system default valuesdefault
Configure default values for switchport attributesswitchport
Enter the port modemode
F system default port modeF
Configure trunking parameters as a defaulttrunk
Configure trunking modemode1
Autosense trunkingauto
Disable trunkingoff
Enable trunkingon
Configure system delayed trap valuesdelayed-traps
Configure system delayed trap stateenable
Configure system delayed trap statemode2
Configure system delayed trap stateFX
Configure system delayed trap timeout valuetimer
Configure number of minutesi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4418
S Commandssystem
Page 4563
system[no] system { { routing { hierarchical def-max-mode l3 64b-alpm | non-hierarchical [ max-mode l3-nh [64b-alpm-nh ] ] | max-mode host | max-mode-tor { l2 | l3 | l2-l3 } | template-overlay-host-scale |template-lpm-heavy | template-lpm-scale-v6-64 | template-dual-stack-host-scale | template-service-provider| template-multicast-heavy | template-multicast-ext-heavy | template-vxlan-scale | template-mpls-heavy |template-internet-peering | template-multicast-nbm | template-l3-heavy } } | { non-hierarchical-routing [max-l3-mode ] } }
Syntax Description
(Optional) Negate a command or set its defaultsno
System Management Commandssystem
Layer-3 routingrouting
Host routing on LC and LPM routing in FMhierarchical
Disablemode of host routing on LC and LPM routing in Fabric modulesnon-hierarchical
Disablemode of host routing on LC and LPM routing in Fabric modulesnon-hierarchical-routing
Maximum scale to be enableddef-max-mode
(Optional) Maximum scale to be enabledmax-mode
Maximum scale to be enabledmax-mode-tor
Max Layer-2 records and fewer Layer-3 host routesl2
Layer-3 longest-prefix-match (LPM) routesl3
Balance of both Layer-2 records and Layer-3 host routesl2-l3
(Optional) Layer-3 longest-prefix-match (LPM) routesl3-nh
IPv6 routes with masks /64 or shorter64b-alpm
(Optional) IPv6 routes with masks /64 or shorter64b-alpm-nh
(Optional) Enable ALPM mode (Mode-4 in T2)max-l3-mode
host routeshost
Internet Peeringtemplate-internet-peering
Overlay Host Scaletemplate-overlay-host-scale
LPM Heavytemplate-lpm-heavy
LPM Scale V6 64template-lpm-scale-v6-64
Dual Stack Host Scaletemplate-dual-stack-host-scale
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4419
S Commandssystem
Page 4564
Service Providertemplate-service-provider
Multicast Heavy Scaletemplate-multicast-heavy
Multicast Extended Heavy Scaletemplate-multicast-ext-heavy
Multicast NBM Scaletemplate-multicast-nbm
L3 Heavy Scale profile for Tofino chipsettemplate-l3-heavy
MPLS Heavy Scaletemplate-mpls-heavy
Vxlan Scaletemplate-vxlan-scale
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4420
S Commandssystem
Page 4565
system acl[no] system acl
Syntax Description
(Optional) Negate a command or set its defaultsno
System management commandssystem
ACL parametersacl
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4421
S Commandssystem acl
Page 4566
system auto-collect tech-supportsystem [ no ] auto-collect tech-support [ timeout <time> ]
Syntax Description
System management commandssystem
(Optional) Negate a command or set its defaultsno
Auto collection of informationauto-collect
Collect tech-support in case of service causing supervisor resettech-support
(Optional) Collect tech-support timeouttimeout
(Optional) Timeout in secondstime
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4422
S Commandssystem auto-collect tech-support
Page 4567
system cores{ system cores { { <uri0> } | { <uri1> vrf <vrf-known-name> } } | no system cores [ { { <uri0> } | { <uri1>vrf <vrf-known-name> } } ] }
Syntax Description
Negate a command or set its defaultsno
System configuration commandssystem
Copy cores to destinationcores
Select destination filesystemuri0
Select destination filesystemuri1
Enter the vrf namevrf
VRF namevrf-known-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4423
S Commandssystem cores
Page 4568
system default interface-vlan autostate[no] system default interface-vlan autostate
Syntax Description
(Optional) Negate a command or set its defaultsno
System configuration commandssystem
Configure interface-vlaninterface-vlan
Configure system default valuesdefault
Enable or disable autostate for entire systemautostate
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4424
S Commandssystem default interface-vlan autostate
Page 4569
system default interface{ system default interface { congestion { timeout <i0> mode { core | edge } | mode { core | edge } } | pause{ timeout <i1> mode1 { core | edge } | mode1 { core | edge } } } | no system default interface { congestion {timeout <i0> mode { core | edge } | mode { core | edge } } | pause { timeout <i1> mode1 { core | edge } |mode1 { core | edge } } } }
Syntax Description
Negate a command or set its defaultsno
System configuration commandssystem
Configure system default valuesdefault
Configure system default interface valuesinterface
Configure system timeout values for congestion dropcongestion
Configure system timeout values for pause framepause
Configure system timeout valuestimeout
Configure number of millisecondsi0
Configure number of millisecondsi1
Configure modemode
Configure modemode1
Enter the port typecore
Enter the port typeedge
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4425
S Commandssystem default interface
Page 4570
system default interface{ system default interface { congestion { timeout <i0> mode { core | edge } | mode { core | edge } } | pause{ timeout <i1> mode1 { core | edge } | mode1 { core | edge } } } | no system default interface { congestion {timeout <i0> mode { core | edge } | mode { core | edge } } | pause { timeout <i1> mode1 { core | edge } |mode1 { core | edge } } } }
Syntax Description
Negate a command or set its defaultsno
System configuration commandssystem
Configure system default valuesdefault
Configure system default interface valuesinterface
Configure system timeout values for congestion dropcongestion
Configure system timeout values for pause framepause
Configure system timeout valuestimeout
Configure number of millisecondsi0
Configure number of millisecondsi1
Configure modemode
Configure modemode1
Enter the port typecore
Enter the port typeedge
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4426
S Commandssystem default interface
Page 4571
system default switchport{ [ no ] system default switchport }
Syntax Description
(Optional) Negate a command or set its defaultsno
System configuration commandssystem
Configure system default valuesdefault
Configure switchportswitchport
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4427
S Commandssystem default switchport
Page 4572
system default switchport shutdown{ [ no ] system default switchport shutdown }
Syntax Description
(Optional) Negate a command or set its defaultsno
System configuration commandssystem
Configure system default valuesdefault
Configure switchportswitchport
Configure admin stateshutdown
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4428
S Commandssystem default switchport shutdown
Page 4573
system default tx-credit double-queue[no] system default tx-credit double-queue
Syntax Description
(Optional) Negate a command or set its defaultsno
System configuration commandssystem
Configure system default valuesdefault
Configure default values for tx credit queue typetx-credit
Configure tx credit queue as double queuedouble-queue
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4429
S Commandssystem default tx-credit double-queue
Page 4574
system dot1q-tunnel transit[no] system dot1q-tunnel transit
Syntax Description
(Optional) Negate a command or set its defaultsno
System Management Commandssystem
Dot1Q tunneldot1q-tunnel
Transit box for multi-tag Ethernet Framestransit
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4430
S Commandssystem dot1q-tunnel transit
Page 4575
system fabric-mode full-rate[no] system fabric-mode full-rate
Syntax Description
(Optional) Negate a command or set its defaultsno
System Management Commandssystem
Configure the operating mode of the fabricsfabric-mode
Operates fabrics in Full Rate Modefull-rate
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4431
S Commandssystem fabric-mode full-rate
Page 4576
system fabric core-vlans{ system fabric core-vlans <id> | no system fabric core-vlans }
Syntax Description
Negate a command or set its defaultsno
System management commandssystem
Manage fabric dynamic vlan rangesfabric
Configure the dynamic core vlan rangecore-vlans
VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4432
S Commandssystem fabric core-vlans
Page 4577
system fabric dynamic-vlans{ system fabric dynamic-vlans <id> | no system fabric dynamic-vlans }
Syntax Description
Negate a command or set its defaultsno
System management commandssystem
Manage fabric dynamic vlan rangesfabric
Configure the dynamic server and core vlan rangedynamic-vlans
VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4433
S Commandssystem fabric dynamic-vlans
Page 4578
system fast-reload stabilization-timersystem fast-reload stabilization-timer <time>
Syntax Description
System management commandssystem
fast-reload softwarefast-reload
Network stabilization time in seconds before fast-reload can be executedafter the previous reload
stabilization-timer
time in secstime
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4434
S Commandssystem fast-reload stabilization-timer
Page 4579
system hap-resetsystem hap-reset
Syntax Description
System management commandssystem
enables resetting of local or remote sup on ha failureshap-reset
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4435
S Commandssystem hap-reset
Page 4580
system hap-resetsystem no hap-reset
Syntax Description
System management commandssystem
Negate a command or set its defaultsno
enables resetting of local or remote sup on ha failureshap-reset
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4436
S Commandssystem hap-reset
Page 4581
system health check bootflashsystem health check bootflash [ fix-errors ]
Syntax Description
System management commandssystem
system health exec commandshealth
run consistency check on compact flashcheck
check internal bootflashbootflash
(Optional) fix bootflash errorsfix-errors
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4437
S Commandssystem health check bootflash
Page 4582
system heartbeatsystem no heartbeat
Syntax Description
System management commandssystem
Negate a command or set its defaultsno
enables heartbeatheartbeat
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4438
S Commandssystem heartbeat
Page 4583
system heartbeatsystem heartbeat
Syntax Description
System management commandssystem
enables heartbeatheartbeat
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4439
S Commandssystem heartbeat
Page 4584
system high-multicast-priority[no] system high-multicast-priority
Syntax Description
(Optional) Negate a command or set its defaultsno
System Management Commandssystem
high priority to multicasthigh-multicast-priority
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4440
S Commandssystem high-multicast-priority
Page 4585
system inband queuing[no] system inband queuing [ { [ round-robin ] [ bpdu weight <weight-val> ] [ q0 weight <weight-val> ] [ q1weight <weight-val> ] [ q0 no-drop ] [ q1 no-drop ] [ pick_packets ] [ bpdu map <q-index> ] [ arp map<q-index> ] [ q0 map <q-index> ] [ q1 map <q-index> ] } ]
Syntax Description
(Optional) Negate a command or set its defaultsno
System-related show commandssystem
System Inband configurationinband
System Inband Queueing Algorithmqueuing
(Optional) Simple Round-Robinround-robin
(Optional) bpdu queuebpdu
(Optional) arp queuearp
(Optional) q0 queue (cos 4,5,6,7)q0
(Optional) q1 queue (cos 0,1,2,3)q1
(Optional) weight associated with the queueweight
(Optional) set no drop option on queueno-drop
(Optional) weightsweight-val
(Optional) enable packet rxpick_packets
(Optional) map to queuemap
(Optional) queue indexq-index
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4441
S Commandssystem inband queuing
Page 4586
system inband queuingsystem inband queuing { clear-pm-counters | clear-klm-counters | clear-all-counters | enable-timestamp |disable-timestamp }
Syntax Description
System-related show commandssystem
System Inband configurationinband
System Inband Queueing Algorithmqueuing
clear user space inband queue countersclear-pm-counters
clear KLM VDC inband queue countersclear-klm-counters
clear all inband queue countersclear-all-counters
enable timestamping in klm vdcenable-timestamp
disable timestamping in klm vdcdisable-timestamp
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4442
S Commandssystem inband queuing
Page 4587
system interface shutdown[no] system interface shutdown [ exclude fex-fabric ]
Syntax Description
(Optional) Negate a command or set its defaultsno
System configuration commandssystem
Configure system interface configinterface
Configure interface shutdownshutdown
(Optional) excludeexclude
(Optional) fex-fabricfex-fabric
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4443
S Commandssystem interface shutdown
Page 4588
system jumbomtu{ system jumbomtu <mtu> | no system jumbomtu [ <mtu> ] }
Syntax Description
Negate a command or set its defaultsno
System configuration commandssystem
Configure system jumbomtujumbomtu
Enter jumbomtumtu
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4444
S Commandssystem jumbomtu
Page 4589
system kgdbsystem no kgdb
Syntax Description
System management commandssystem
Negate a command or set its defaultsno
enables kgdbkgdb
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4445
S Commandssystem kgdb
Page 4590
system kgdbsystem kgdb
Syntax Description
System management commandssystem
enables kgdbkgdb
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4446
S Commandssystem kgdb
Page 4591
system login block-for[no] system login block-for
Syntax Description
Negate a command or set its defaultsno
System configuration commandssystem
Enable secure login checkinglogin
Set quiet-mode active time periodblock-for
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4447
S Commandssystem login block-for
Page 4592
system login block-for attempts withinsystem login block-for <i1> attempts <i2> within <i3>
Syntax Description
System configuration commandssystem
Enable secure login checkinglogin
Set quiet-mode active time periodblock-for
Time period in secondsi1
Set max number of fail attemptsattempts
Fail attempts max valuei2
Watch period for fail attemptswithin
Time period in secondsi3
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4448
S Commandssystem login block-for attempts within
Page 4593
system login quiet-mode[no] system login quiet-mode
Syntax Description
Negate a command or set its defaultsno
System configuration commandssystem
Enable secure login checkinglogin
Set quiet-mode optionsquiet-mode
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4449
S Commandssystem login quiet-mode
Page 4594
system login quiet-mode access-classsystem login quiet-mode access-class <access-list>
Syntax Description
System configuration commandssystem
Enable secure login checkinglogin
Set quiet-mode optionsquiet-mode
Set access classaccess-class
Access-list nameaccess-list
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4450
S Commandssystem login quiet-mode access-class
Page 4595
system memory-thresholds minor severe critical[no] system memory-thresholds minor <minor> severe <severe> critical <crit>
Syntax Description
(Optional) Negate a command or set its defaultsno
System configuration commandssystem
Set memory thresholds on the cardmemory-thresholds
enter minor thresholdminor
please enter minor memory threshold as % memoryminor
enter severe tresholdsevere
please enter severe memory threshold as % memorysevere
enter critical tresholdcritical
please enter critical memory threshold as % memorycrit
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4451
S Commandssystem memory-thresholds minor severe critical
Page 4596
system mode maintenance[no] system mode maintenance [ dont-generate-profile ] [ non-interactive ] | system mode maintenance [dont-generate-profile | shutdown ] [ non-interactive ]
Syntax Description
Negate a command or set its defaultsno
System configuration commandssystem
system mode commandsmode
system maintenance modemaintenance
(Optional) do not generate the maintenance/normal-mode profiledont-generate-profile
(Optional) issue shutdown instead of isolate (default)shutdown
(Optional) do operation non interactively in backgroundnon-interactive
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4452
S Commandssystem mode maintenance
Page 4597
system mode maintenance always-use-custom-profile[no] system mode maintenance always-use-custom-profile
Syntax Description
(Optional) Negate a command or set its defaultsno
System configuration commandssystem
system mode commandsmode
system maintenance modemaintenance
always use custom profile when entering maintenance modealways-use-custom-profile
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4453
S Commandssystem mode maintenance always-use-custom-profile
Page 4598
system mode maintenance maint-delay[no] system mode maintenance maint-delay <delay-value>
Syntax Description
(Optional) Negate a command or set its defaultsno
System configuration commandssystem
system mode commandsmode
system maintenance modemaintenance
delay to allow protocol reroute before releasing CLImaint-delay
delay value in secondsdelay-value
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4454
S Commandssystem mode maintenance maint-delay
Page 4599
system mode maintenance on-reload reset-reason[no] system mode maintenance on-reload reset-reason <reason>
Syntax Description
(Optional) Negate a command or set its defaultsno
System configuration commandssystem
system mode commandsmode
system maintenance modemaintenance
on reload maintenance mode configurationon-reload
reset reasonreset-reason
reason
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4455
S Commandssystem mode maintenance on-reload reset-reason
Page 4600
system mode maintenance snapshot-delay[no] system mode maintenance snapshot-delay <delay-value>
Syntax Description
(Optional) Negate a command or set its defaultsno
System configuration commandssystem
system mode commandsmode
system maintenance modemaintenance
delay after which after_maintenance snapshot will be takensnapshot-delay
delay value in secondsdelay-value
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4456
S Commandssystem mode maintenance snapshot-delay
Page 4601
system mode maintenance timeout[no] system mode maintenance timeout <timer-value>
Syntax Description
(Optional) Negate a command or set its defaultsno
System configuration commandssystem
system mode commandsmode
system maintenance modemaintenance
restart maintenance mode timer with a new valuetimeout
timer value in minutestimer-value
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4457
S Commandssystem mode maintenance timeout
Page 4602
system module emon-enhanced[no] system module emon-enhanced
Syntax Description
(Optional) Negate a command or set its defaultsno
system Internal Informationsystem
module commandsmodule
Configure emon enhanced supportemon-enhanced
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4458
S Commandssystem module emon-enhanced
Page 4603
system module failure-action shutdown[no] system module failure-action shutdown
Syntax Description
(Optional) Negate a command or set its defaultsno
system Internal Informationsystem
module commandsmodule
Configure module action on failurefailure-action
action on failure - shutdownshutdown
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4459
S Commandssystem module failure-action shutdown
Page 4604
system mrouting[no] system mrouting [ performance-mode | disable-2nd-update | disable-l2-update ]
Syntax Description
(Optional) Negate a command or set its defaultsno
System Management Commandssystem
Layer-3 mroutingmrouting
(Optional) Multicast Performance Modeperformance-mode
(Optional) Disable 2nd route updatedisable-2nd-update
(Optional) Disable l2 route updatedisable-l2-update
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4460
S Commandssystem mrouting
Page 4605
system poapsystem poap
Syntax Description
System management commandssystem
Re-enable POAP on every write erase+reloadpoap
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4461
S Commandssystem poap
Page 4606
system poapsystem no poap
Syntax Description
System management commandssystem
Negate a command or set its defaultsno
This will set a boot flag, that will allow disabling POAP permanentlyeven when the system starts with no configuration
poap
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4462
S Commandssystem poap
Page 4607
system pss shrinksystem pss shrink
Syntax Description
System management commandssystem
PSS commandspss
shrink pss filesshrink
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4463
S Commandssystem pss shrink
Page 4608
system qossystem qos
Syntax Description
System management commandssystem
QoS parametersqos
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4464
S Commandssystem qos
Page 4609
system routing unknown-unicast-flood[no] system routing unknown-unicast-flood
Syntax Description
(Optional) Negate a command or set its defaultsno
System Management Commandssystem
Layer-3 routingrouting
Hardware flood post-routed traffic on SVI if dest-mac->layer2-portbinding unknown
unknown-unicast-flood
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4465
S Commandssystem routing unknown-unicast-flood
Page 4610
system security compliance common-criteria[no] system security compliance common-criteria
Syntax Description
(Optional) Negate a command or set its defaultsno
System Management commandssystem
Security Management commandssecurity
Compliant with the mode configuredcompliance
Enable/Disable common-criteria modecommon-criteria
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4466
S Commandssystem security compliance common-criteria
Page 4611
system shutdown fan-direction mismatchsystem shutdown fan-direction mismatch | no system shutdown fan-direction mismatch
Syntax Description
Negate a command or set its defaultsno
System management commandssystem
Shutdown management commandsshutdown
Fan-direction checkfan-direction
Mismatch in checkmismatch
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4467
S Commandssystem shutdown fan-direction mismatch
Page 4612
system simulate fan-presencesystem simulate fan-presence | no system simulate fan-presence
Syntax Description
Negate a command or set its defaultsno
System management commandssystem
Simulate Fan Presencesimulate
Simulate Fan Presencefan-presence
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4468
S Commandssystem simulate fan-presence
Page 4613
system standby manual-bootsystem standby manual-boot
Syntax Description
System management commandssystem
System standby management commandsstandby
No action taken to force-download standby supmanual-boot
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4469
S Commandssystem standby manual-boot
Page 4614
system standby manual-bootsystem no standby manual-boot
Syntax Description
System management commandssystem
Negate a command or set its defaultsno
System standby manual bootstandby
No action taken to force-download standby supmanual-boot
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4470
S Commandssystem standby manual-boot
Page 4615
system startup-config initsystem startup-config init
Syntax Description
System management commandssystem
System startup-config commandsstartup-config
Initialize the startup-configurationinit
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4471
S Commandssystem startup-config init
Page 4616
system startup-config unlocksystem startup-config unlock <i0>
Syntax Description
System management commandssystem
System startup-config commandsstartup-config
Unlock startup-configunlock
Startup-config lock idi0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4472
S Commandssystem startup-config unlock
Page 4617
system statisticssystem statistics
Syntax Description
System management commandssystem
enables sysmgr statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4473
S Commandssystem statistics
Page 4618
system statisticssystem no statistics
Syntax Description
System management commandssystem
Negate a command or set its defaultsno
disable the sysmgr statisticsstatistics
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4474
S Commandssystem statistics
Page 4619
system switch-modesystem switch-mode { <mode> }
Syntax Description
System management commandssystem
change switch operational modeswitch-mode
switch modemode
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4475
S Commandssystem switch-mode
Page 4620
system switchoversystem switchover
Syntax Description
System management commandssystem
Switch over to the standby supervisorswitchover
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4476
S Commandssystem switchover
Page 4621
system switchover forcesystem switchover force
Syntax Description
System management commandssystem
Switch over to the standby supervisorswitchover
Force switch over to the standby supervisorforce
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4477
S Commandssystem switchover force
Page 4622
system timeout{ system timeout { congestion-drop { <i0>mode <port_mode> | default mode <port_mode> } | no-credit-drop{ <i1> mode1 <port_mode1> | default mode1 <port_mode1> } } | no system timeout no-credit-drop mode1<port_mode1> }
Syntax Description
Negate a command or set its defaultsno
System configuration commandssystem
Configure system timeout valuestimeout
Configure system timeout values for congestion dropcongestion-drop
Configure number of millisecondsi0
Default timeout value for congestion-dropdefault
Enter the port modemode
Port modeport_mode
Configure system timeout values for no credit dropno-credit-drop
Configure number of millisecondsi1
Default timeout value for no-credit-dropdefault
Enter the port modemode1
Port modeport_mode1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4478
S Commandssystem timeout
Page 4623
system trace{ system trace <i0> | no system trace [ <i0> ] }
Syntax Description
Negate a command or set its defaultsno
System configuration commandssystem
To configure system trace leveltrace
Select the maski0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4479
S Commandssystem trace
Page 4624
system urpf disable[no] system urpf disable
Syntax Description
(Optional) Negate a command or set its defaultsno
System Management Commandssystem
Manage urpf enable/disableurpf
disabledisable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4480
S Commandssystem urpf disable
Page 4625
system vlan long-name[no] system vlan long-name
Syntax Description
(Optional) Negate a command or set its defaultsno
System management commandssystem
Vlan commandsvlan
Configure 128 character VLAN nameslong-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4481
S Commandssystem vlan long-name
Page 4626
system vlan reservesystem vlan <start-val> reserve | no system vlan <start-val> reserve
Syntax Description
system wide configurationsystem
Select default reserved vlans group vlan 3968-4094no
Vlan commandsvlan
minimum VLANs valuestart-val
reservationreserve
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4482
S Commandssystem vlan reserve
Page 4627
system vrf-member-change retain-l3-config[no] system vrf-member-change retain-l3-config
Syntax Description
(Optional) Negate a command or set its defaultsno
System management commandssystem
vrf member changevrf-member-change
retain L3 configurationretain-l3-config
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4483
S Commandssystem vrf-member-change retain-l3-config
Page 4628
system watchdogsystem no watchdog
Syntax Description
System management commandssystem
Negate a command or set its defaultsno
enables watchdogwatchdog
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4484
S Commandssystem watchdog
Page 4629
system watchdogsystem watchdog
Syntax Description
System management commandssystem
enables watchdogwatchdog
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4485
S Commandssystem watchdog
Page 4630
system watchdog kgdbsystem no watchdog kgdb
Syntax Description
System management commandssystem
Negate a command or set its defaultsno
enables watchdogwatchdog
enter kgdb on watchdog failurekgdb
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4486
S Commandssystem watchdog kgdb
Page 4631
system watchdog kgdbsystem watchdog kgdb
Syntax Description
System management commandssystem
enables watchdogwatchdog
enter kgdb on watchdog failurekgdb
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4487
S Commandssystem watchdog kgdb
Page 4632
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4488
S Commandssystem watchdog kgdb
Page 4633
T Commands
• table-map, on page 4496• table-map, on page 4497• table-map, on page 4498• table-map, on page 4499• table-map, on page 4500• table-map, on page 4501• table-map, on page 4502• table-map, on page 4503• tac-pac, on page 4504• tac-pac, on page 4505• tacacs-server deadtime, on page 4506• tacacs-server directed-request, on page 4507• tacacs-server host key 0 6 7, on page 4508• tacacs-server host test, on page 4509• tacacs-server key 0 6 7, on page 4510• tacacs-server test, on page 4511• tacacs-server timeout, on page 4512• tacacs enable, on page 4513• tag, on page 4514• tag happens in, on page 4515• tahoe-python module, on page 4516• tahoe-python module quoted, on page 4517• tail, on page 4518• tail, on page 4519• tar, on page 4520• tclsh, on page 4521• tclsh, on page 4522• tcp-connect, on page 4523• telnet, on page 4524• telnet6, on page 4525• telnet login-attempts, on page 4526• telnet server enable, on page 4527• template, on page 4528
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4489
Page 4634
• template data timeout, on page 4529• template peer-policy, on page 4530• template peer-session, on page 4531• template peer, on page 4532• terminal, on page 4533• terminal alias, on page 4534• terminal ask-on-term, on page 4535• terminal color, on page 4536• terminal context management, on page 4537• terminal deep-help, on page 4538• terminal dont-ask, on page 4539• terminal edit-mode vi, on page 4540• terminal event-manager bypass, on page 4541• terminal history no-exec-in-config, on page 4542• terminal history no-exec-in-config, on page 4543• terminal history no-exec-in-config, on page 4544• terminal home, on page 4545• terminal length, on page 4546• terminal length, on page 4547• terminal log-all, on page 4548• terminal no, on page 4549• terminal output xml, on page 4550• terminal output xml, on page 4551• terminal output xml, on page 4552• terminal password, on page 4553• terminal prompt, on page 4554• terminal redirection-mode, on page 4555• terminal session-timeout, on page 4556• terminal sticky-mode, on page 4557• terminal terminal-type, on page 4558• terminal time, on page 4559• terminal tree-update, on page 4560• terminal verify-only, on page 4561• terminal width, on page 4562• terminal width, on page 4563• threshold-percent, on page 4564• threshold, on page 4565• time-range, on page 4566• timeout, on page 4567• timeout, on page 4568• timeout, on page 4569• timer, on page 4570• timer, on page 4571• timer inactivity, on page 4572• timers, on page 4573• timers, on page 4574
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4490
T Commands
Page 4635
• timers, on page 4575• timers advertise, on page 4576• timers basic, on page 4577• timers bestpath-defer maximum, on page 4578• timers bestpath-limit, on page 4579• timers bgp, on page 4580• timers lsa-arrival, on page 4581• timers lsa-arrival, on page 4582• timers lsa-group-pacing, on page 4583• timers lsa-group-pacing, on page 4584• timers prefix-peer-timeout, on page 4585• timers prefix-peer-wait, on page 4586• timers srgb cleanup, on page 4587• timers srgb retry, on page 4588• timers throttle lsa, on page 4589• timers throttle lsa, on page 4590• timers throttle spf, on page 4591• timers throttle spf, on page 4592• timestamp timestamp, on page 4593• tls trust-point local remote, on page 4594• tls trust-point local remote, on page 4595• topology, on page 4596• topology holddown sigerr, on page 4597• tos, on page 4598• tr, on page 4599• trace buffer size, on page 4600• traceroute, on page 4601• traceroute6, on page 4602• track-adjacency-nexthop, on page 4603• track, on page 4604• track, on page 4605• track, on page 4606• track, on page 4607• track, on page 4608• track, on page 4609• track, on page 4610• track, on page 4611• track, on page 4612• track, on page 4613• track data, on page 4614• track interface, on page 4615• track interface priority, on page 4616• track running-state track startup-state, on page 4617• tracking enable, on page 4618• traffic-class, on page 4619• traffic-engineering, on page 4620
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4491
T Commands
Page 4636
• transmit-delay, on page 4621• transmit-delay, on page 4622• transmit-delay, on page 4623• transport connection-mode passive, on page 4624• transport email, on page 4625• transport email mail-server, on page 4626• transport http proxy enable, on page 4627• transport http proxy server, on page 4628• transport http use-vrf, on page 4629• transport udp, on page 4630• transport udp, on page 4631• transport udp, on page 4632• transport udp source-port, on page 4633• trigger forwarding distribution module, on page 4634• trigger init, on page 4635• trigger init in-select 10, on page 4636• trigger init in-select 10 out-select 0, on page 4637• trigger init in-select 10 out-select 1, on page 4638• trigger init in-select 10 out-select 2, on page 4639• trigger init in-select 19, on page 4640• trigger init in-select 19 out-select 0, on page 4641• trigger init in-select 19 out-select 1, on page 4642• trigger init in-select 19 out-select 2, on page 4643• trigger init in-select 6, on page 4644• trigger init in-select 6 out-select 0, on page 4645• trigger init in-select 6 out-select 1, on page 4646• trigger init in-select 6 out-select 2, on page 4647• trigger init in-select 7, on page 4648• trigger init in-select 7 out-select 0, on page 4649• trigger init in-select 7 out-select 1, on page 4650• trigger init in-select 7 out-select 2, on page 4651• trigger init in-select 8, on page 4652• trigger init in-select 8 out-select 0, on page 4653• trigger init in-select 8 out-select 1, on page 4654• trigger init in-select 8 out-select 2, on page 4655• trigger init in-select 9, on page 4656• trigger init in-select 9 out-select 0, on page 4657• trigger init in-select 9 out-select 1, on page 4658• trigger init in-select 9 out-select 2, on page 4659• trigger init ingress in-select 3 out-select 0, on page 4660• trigger init ingress in-select 3 out-select 03, on page 4661• trigger init ingress in-select 3 out-select 0 reverse, on page 4662• trigger init ingress in-select 3 out-select 1, on page 4663• trigger init ingress in-select 3 out-select 2, on page 4664• trigger init ingress in-select 3 out-select 4, on page 4665• trigger init ingress in-select 3 out-select 5, on page 4666
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4492
T Commands
Page 4637
• trigger init ingress in-select 3 out-select 5 reverse, on page 4667• trigger init ingress in-select 4 out-select 0, on page 4668• trigger init ingress in-select 4 out-select 04, on page 4669• trigger init ingress in-select 4 out-select 0 reverse, on page 4670• trigger init ingress in-select 4 out-select 1, on page 4671• trigger init ingress in-select 4 out-select 2, on page 4672• trigger init ingress in-select 4 out-select 3, on page 4673• trigger init ingress in-select 4 out-select 5, on page 4674• trigger init ingress in-select 4 out-select 5 reverse, on page 4675• trigger init ingress in-select 5 out-select 0, on page 4676• trigger init ingress in-select 5 out-select 05, on page 4677• trigger init ingress in-select 5 out-select 05 reverse, on page 4678• trigger init ingress in-select 5 out-select 0 reverse, on page 4679• trigger init ingress in-select 5 out-select 1, on page 4680• trigger init ingress in-select 5 out-select 2, on page 4681• trigger init ingress in-select 5 out-select 3, on page 4682• trigger init ingress in-select 5 out-select 4, on page 4683• trigger init ingress in-select 6 out-select 0, on page 4684• trigger init ingress in-select 6 out-select 0 reverse, on page 4685• trigger init ingress in-select 6 out-select 1, on page 4686• trigger init ingress in-select 6 out-select 2, on page 4687• trigger init ingress in-select 6 out-select 3, on page 4688• trigger init ingress in-select 6 out-select 4, on page 4689• trigger init ingress in-select 6 out-select 5, on page 4690• trigger init ingress in-select 6 out-select 5 reverse, on page 4691• trigger init ingress in-select 7 out-select 0, on page 4692• trigger init ingress in-select 7 out-select 0 reverse, on page 4693• trigger init ingress in-select 7 out-select 1, on page 4694• trigger init ingress in-select 7 out-select 2, on page 4695• trigger init ingress in-select 7 out-select 3, on page 4696• trigger init ingress in-select 7 out-select 4, on page 4697• trigger init ingress in-select 7 out-select 5, on page 4698• trigger init ingress in-select 7 out-select 5 reverse, on page 4699• trigger init lu-a2d 0, on page 4700• trigger init lu-a2d 0 in-select 10 out-select 0, on page 4701• trigger init lu-a2d 0 in-select 10 out-select 1, on page 4702• trigger init lu-a2d 0 in-select 10 out-select 2, on page 4703• trigger init lu-a2d 0 in-select 19 out-select 0, on page 4704• trigger init lu-a2d 0 in-select 19 out-select 1, on page 4705• trigger init lu-a2d 0 in-select 19 out-select 2, on page 4706• trigger init lu-a2d 0 in-select 6 out-select 0, on page 4707• trigger init lu-a2d 0 in-select 6 out-select 1, on page 4708• trigger init lu-a2d 0 in-select 6 out-select 2, on page 4709• trigger init lu-a2d 0 in-select 7 out-select 0, on page 4710• trigger init lu-a2d 0 in-select 7 out-select 1, on page 4711• trigger init lu-a2d 0 in-select 7 out-select 2, on page 4712
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4493
T Commands
Page 4638
• trigger init lu-a2d 0 in-select 8 out-select 0, on page 4713• trigger init lu-a2d 0 in-select 8 out-select 1, on page 4714• trigger init lu-a2d 0 in-select 8 out-select 2, on page 4715• trigger init lu-a2d 0 in-select 9 out-select 0, on page 4716• trigger init lu-a2d 0 in-select 9 out-select 1, on page 4717• trigger init lu-a2d 0 in-select 9 out-select 2, on page 4718• trigger init lu-a2d 0 out-select 0, on page 4719• trigger init lu-a2d 0 out-select 1, on page 4720• trigger init lu-a2d 0 out-select 2, on page 4721• trigger init lu-a2d 1, on page 4722• trigger init lu-a2d 1 in-select 10, on page 4723• trigger init lu-a2d 1 in-select 10 out-select 0, on page 4724• trigger init lu-a2d 1 in-select 10 out-select 1, on page 4725• trigger init lu-a2d 1 in-select 10 out-select 2, on page 4726• trigger init lu-a2d 1 in-select 19, on page 4727• trigger init lu-a2d 1 in-select 19 out-select 0, on page 4728• trigger init lu-a2d 1 in-select 19 out-select 1, on page 4729• trigger init lu-a2d 1 in-select 19 out-select 2, on page 4730• trigger init lu-a2d 1 in-select 6, on page 4731• trigger init lu-a2d 1 in-select 6 out-select 0, on page 4732• trigger init lu-a2d 1 in-select 6 out-select 1, on page 4733• trigger init lu-a2d 1 in-select 6 out-select 2, on page 4734• trigger init lu-a2d 1 in-select 7, on page 4735• trigger init lu-a2d 1 in-select 7 out-select 0, on page 4736• trigger init lu-a2d 1 in-select 7 out-select 1, on page 4737• trigger init lu-a2d 1 in-select 7 out-select 2, on page 4738• trigger init lu-a2d 1 in-select 8, on page 4739• trigger init lu-a2d 1 in-select 8 out-select 0, on page 4740• trigger init lu-a2d 1 in-select 8 out-select 1, on page 4741• trigger init lu-a2d 1 in-select 8 out-select 2, on page 4742• trigger init lu-a2d 1 in-select 9, on page 4743• trigger init lu-a2d 1 in-select 9 out-select 0, on page 4744• trigger init lu-a2d 1 in-select 9 out-select 1, on page 4745• trigger init lu-a2d 1 in-select 9 out-select 2, on page 4746• trigger init out-select 0, on page 4747• trigger init out-select 1, on page 4748• trigger init out-select 2, on page 4749• trigger reset, on page 4750• trigger route download vrf ipv4, on page 4751• trunk protocol, on page 4752• trusted-port, on page 4753• trusted-port, on page 4754• trusted-port, on page 4755• ttag-marker-interval, on page 4756• ttag-marker-interval, on page 4757• ttag-marker enable, on page 4758
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4494
T Commands
Page 4639
• ttag-marker enable, on page 4759• ttag-strip, on page 4760• ttag, on page 4761• ttag, on page 4762• ttl-security hops, on page 4763• tunnel destination, on page 4764• tunnel mode, on page 4765• tunnel path-mtu-discovery, on page 4766• tunnel path-mtu-discovery age-timer, on page 4767• tunnel path-mtu-discovery min-mtu, on page 4768• tunnel source, on page 4769• tunnel ttl, on page 4770• tunnel use-vrf, on page 4771
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4495
T Commands
Page 4640
table-map[no] table-map <policy-name> [ filter ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Policy for filtering/modifying OSPFV3 routes before sending them toRIB
table-map
Route-map namepolicy-name
(Optional) To block the OSPFV3 routes from being sent to RIBfilter
Command Mode
• /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4496
T Commandstable-map
Page 4641
table-map[no] table-map <table-map-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a table maptable-map
Table map nametable-map-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4497
T Commandstable-map
Page 4642
table-maptable-map <default-tmap-enum-name>
Syntax Description
Configure a table maptable-map
default-tmap-enum-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4498
T Commandstable-map
Page 4643
table-map[no] table-map <policy-name> [ filter ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Table-map policy used to filter routes and tune attributes beforedownloading to RIB
table-map
(Optional) Filter the routes based on policy resultsfilter
A 'routing-rules' route-map namepolicy-name
Command Mode
• /exec/configure/router-isis/router-isis-vrf-common /exec/configure/router-isis/router-isis-af-ipv4
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4499
T Commandstable-map
Page 4644
table-map[no] table-map <policy-name> [ filter ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Table-map policy used to filter routes and tune attributes beforedownloading to RIB
table-map
(Optional) Filter the routes based on policy resultsfilter
A 'routing-rules' route-map namepolicy-name
Command Mode
• /exec/configure/router-isis/router-isis-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4500
T Commandstable-map
Page 4645
table-map[no] table-map <map> [ filter ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Table Map informationtable-map
Route-map namemap
(Optional) Filter routes which are rejected by route-mapfilter
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4501
T Commandstable-map
Page 4646
table-map[no] table-map <policy-name> [ filter ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Policy for filtering/modifying OSPF routes before sending them to RIBtable-map
Route-map namepolicy-name
(Optional) To block the OSPF routes from being sent to RIBfilter
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4502
T Commandstable-map
Page 4647
table-map[no] table-map <rmap-name> [ filter ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Apply table-map to filter routes downloaded into URIBtable-map
Route-map namermap-name
(Optional) Selective route downloadfilter
Command Mode
• /exec/configure/router-bgp/router-bgp-af
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4503
T Commandstable-map
Page 4648
tac-pactac-pac [ <uri0> [ vrf <vrf-known-name> ] ]
Syntax Description
save tac info in a compressed .gz file at specific locationtac-pac
(Optional) Select destination filesystemuri0
(Optional) Display per-VRF informationvrf
(Optional) Known VRF namevrf-known-name
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4504
T Commandstac-pac
Page 4649
tac-pactac-pac [ <uri0> ]
Syntax Description
save tac info in a compressed .gz file at specific locationtac-pac
(Optional) Select destination filesystemuri0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4505
T Commandstac-pac
Page 4650
tacacs-server deadtime[no] tacacs-server deadtime <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure TACACS+ server related parameterstacacs-server
duration for which non-reachable server is skippeddeadtime
Length of time, in minutesi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4506
T Commandstacacs-server deadtime
Page 4651
tacacs-server directed-request[no] tacacs-server directed-request
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure TACACS+ server related parameterstacacs-server
enable direct authentication requests to serverdirected-request
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4507
T Commandstacacs-server directed-request
Page 4652
tacacs-server host key 0 6 7{ { [ no ] tacacs-server host { <hostipname> } { { key { 0 <s0> | 6 <s6> | 7 <s1> | <s2> } [ port <i1> ] [timeout <i2> ] [ single-connection ] } | { [ port1 <i3> ] [ timeout1 <i4> ] [ single-connection ] } | { [single-connection ] } } } | { no tacacs-server host <hostipname> key } }
Syntax Description
0key
(Optional) Negate a command or set its defaultsno
Configure TACACS+ server related parameterstacacs-server
TACACS+ server's DNS name or its IP addresshost
IPV4/IPV6 address or DNS namehostipname
TACACS+ shared secretkey
TACACS+ shared secret(clear text)0
TACACS+ shared secret(clear text)s0
(Optional) TACACS+ server portport
(Optional) TACACS+ server porti1
(Optional) TACACS+ server timeout period in secondstimeout
(Optional) TACACS+ server timeout period in secondsi2
(Optional) Use single connection for this Tacacs+ serversingle-connection
TACACS+ shared secret(type-6 encrypted)6
TACACS+ shared secret(encrypted)s6
TACACS+ shared secret(encrypted)7
TACACS+ shared secret(encrypted)s1
(Optional) TACACS+ server portport1
(Optional) TACACS+ server porti3
(Optional) TACACS+ server timeout period in secondstimeout1
(Optional) TACACS+ server timeout period in secondsi4
TACACS+ shared secret(clear text)s2
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4508
T Commandstacacs-server host key 0 6 7
Page 4653
tacacs-server host test[no] tacacs-server host <hostipnam> test { { username <s0> { [ password <s1> [ idle-time <i1> ] ] | [ idle-time<i1> ] } } | { password <s1> [ idle-time <i1> ] } | { idle-time <i1> } }
Syntax Description
<s0>username
(Optional) Negate a command or set its defaultsno
Configure TACACS+ server related parameterstacacs-server
TACACS+ server's DNS name or its IP addresshost
IPV4/IPV6 address or DNS namehostipnam
Parameters to send test packetstest
user names0
(Optional) user password in test packetspassword
(Optional) user passwords1
(Optional) time interval for monitoring the serveridle-time
(Optional) time period in minutesi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4509
T Commandstacacs-server host test
Page 4654
tacacs-server key 0 6 7{ { [ no ] tacacs-server key { 0 <s0> [ timeout <i0> ] | 6 <s6> [ timeout6 <i6> ] | 7 <s1> [ timeout1 <i1> ] |<s2> [ timeout2 <i2> ] } } | { no tacacs-server key } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure TACACS+ server related parameterstacacs-server
Global TACACS+ server shared secretkey
default TACACS+ shared secret(clear text)0
default TACACS+ shared secret(clear text)s0
(Optional) Global TACACS+ server timeout period in secondstimeout
(Optional) Global TACACS+ server timeout period in secondsi0
default TACACS+ shared secret(type-6 encrypted)6
default TACACS+ shared secret(type-6 encrypted)s6
(Optional) Global TACACS+ server timeout period in secondstimeout6
(Optional) Global TACACS+ server timeout period in secondsi6
default TACACS+ shared secret(encrypted)7
default TACACS+ shared secret(encrypted)s1
(Optional) Global TACACS+ server timeout period in secondstimeout1
(Optional) Global TACACS+ server timeout period in secondsi1
default TACACS+ shared secret(clear text)s2
(Optional) Global TACACS+ server timeout period in secondstimeout2
(Optional) Global TACACS+ server timeout period in secondsi2
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4510
T Commandstacacs-server key 0 6 7
Page 4655
tacacs-server test[no] tacacs-server test { { username <s0> { [ password <s1> [ idle-time <i1> ] ] | [ idle-time <i1> ] } } | {password <s1> [ idle-time <i1> ] } | { idle-time <i1> } }
Syntax Description
<s0>username
(Optional) Negate a command or set its defaultsno
Configure TACACS+ server related parameterstacacs-server
Parameters to send test packetstest
user names0
(Optional) user password in test packetspassword
(Optional) user passwords1
(Optional) time interval for monitoring the serveridle-time
(Optional) time period in minutesi1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4511
T Commandstacacs-server test
Page 4656
tacacs-server timeout[no] tacacs-server timeout <i0>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure TACACS+ server related parameterstacacs-server
Global TACACS+ server timeout period in secondstimeout
Global TACACS+ server timeout period in secondsi0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4512
T Commandstacacs-server timeout
Page 4657
tacacs enable[no] tacacs + enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable tacacs+enable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4513
T Commandstacacs enable
Page 4658
tag{ { no | default } tag | tag <text> }
Syntax Description
no
Set a command to its defaultsdefault
User defined tagtag
Tag string linetext
Command Mode
• /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/tcp/exec/configure/ip-sla/icmpEcho /exec/configure/ip-sla/dns /exec/configure/ip-sla/fabricPathEcho/exec/configure/ip-sla/http
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4514
T Commandstag
Page 4659
tag happens in[no] tag <tag_id> <op> <tag_id> [ <op> <tag_id> [ <op> <tag_id> ] ] happens <threshold> in <interval> |no tag
Syntax Description
(Optional) Negate a command or set its defaultsno
event tag identifiertag
tag nametag_id
boolean operatorop
The number of occurrences before raising the eventhappens
Occurs valuethreshold
Number of occurrences must occur within this time periodin
Enter seconds valueinterval
Command Mode
• /exec/configure/event-manager-applet
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4515
T Commandstag happens in
Page 4660
tahoe-python moduletahoe-python module <module>
Syntax Description
enter python mode for tahoe systemstahoe-python
Module number of the linecardmodule
Enter module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4516
T Commandstahoe-python module
Page 4661
tahoe-python module quotedtahoe-python module <module> quoted <quoted-cmd>
Syntax Description
enter python mode for tahoe systemstahoe-python
Module number of the linecardmodule
Enter module numbermodule
enter the command with quotes Add multiple commands separated bysemi-colon
quoted
the command(s) to run in tahoe pythonquoted-cmd
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4517
T Commandstahoe-python module quoted
Page 4662
tailtail <uri0> [ <i1> ]
Syntax Description
Display the last part of a filetail
Filename to be displayeduri0
(Optional) Enter the number of lines to be displayedi1
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4518
T Commandstail
Page 4663
tail| tail [ -n <lines> ]
Syntax Description
Pipe command output to filter|
Display last linestail
(Optional) modify number of lines (default 10)-n
(Optional) number of lines to printlines
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4519
T Commandstail
Page 4664
tartar { create <new-archive-file> [ gz-compress | bz2-compress | uncompressed ] + [ remove | absolute | verbose] + <files> + | append <archive-file> [ remove | absolute | verbose ] + <files> + | extract <archive-file> [ screen| to <dest-dir> | keep-old | verbose ] + | list <archive-file> }
Syntax Description
archiving operationstar
create an archive (merge several files together)create
append some files to an existing archiveappend
extract files from archive (unmerge them)extract
(Optional) display files while merging/extractingverbose
(Optional) compress archive with gzip, the default -> .tar.gzgz-compress
(Optional) compress archive with bzip2 -> .tar.bz2bz2-compress
(Optional) dont compress archive -> .taruncompressed
(Optional) remove files after adding them to the archiveremove
(Optional) don't strip leading `/'s from file namesabsolute
(Optional) don't replace existing files when extractingkeep-old
(Optional) extract files to screenscreen
shows the list of files which are part of the archivelist
the name of the archive (extension will be added if none oftar/tgz/tar.gz/tar.bz2/tbz2/tar.Z specified)
new-archive-file
the name of the archive (extension will be added if none oftar/tgz/tar.gz/tar.bz2/tbz2/tar.Z specified)
archive-file
name of file to be added into archivefiles
(Optional) extract to specific directory (default is bootflash)to
(Optional) destination dir where to extract to (created if not exist), defaultis bootflash
dest-dir
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4520
T Commandstar
Page 4665
tclshtclsh
Syntax Description
Execute tclshtclsh
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4521
T Commandstclsh
Page 4666
tclshtclsh <file> [ <args> ] +
Syntax Description
source tclsh scripttclsh
the file to runfile
(Optional) args to tcl scriptargs
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4522
T Commandstclsh
Page 4667
tcp-connect[no] tcp-connect { <hostname> | <ip-address> | <ipv6-address> } <dest-port> { [ control { disable | enable }] [ source-ip { <source-ip-hostname> | <source-ip-address> | <source-ipv6-address> } ] [ source-port <src-port>] } +
Syntax Description
(Optional)no
(Optional) enablecontrol
(Optional) <source-ipv6-address>source-ip-address
TCP Connect Operationtcp-connect
Destination hostname, broadcast disallowedhostname
Destination IP address, broadcast disallowedip-address
Port Number (Recommended port range between 1025-65534)dest-port
(Optional) Enable control packets exchange (default)enable
(Optional) Disable control packets exchangedisable
(Optional) Source addresssource-ip
(Optional) source IP hostname, broadcast disallowedsource-ip-hostname
(Optional) Source Portsource-port
(Optional) Port Number (Recommended port range between 1025-65534)src-port
Command Mode
• /exec/configure/ip-sla
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4523
T Commandstcp-connect
Page 4668
telnet{ telnet { <so> | <host> } } [ <i0> ] [ [ source { <host_src> | <interface> } ] [ vrf { <vrf-name> |<vrf-known-name> } ] ]
Syntax Description
Telnet to another systemtelnet
Enter hostnameso
Enter a valid IPv4 addresshost
(Optional) Set source address in IPv4 headersource
(Optional) Set IPV4 address as sourcehost_src
(Optional) Set interface to send IPv4 packetinterface
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Enter the port numberi0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4524
T Commandstelnet
Page 4669
telnet6{ telnet6 { <s1> | <host1> } } [ <i0> ] [ [ source { <host1_src> | <interface> } ] [ vrf { <vrf-name> |<vrf-known-name> } ] ]
Syntax Description
Telnet6 to another system using IPv6 addressingtelnet6
Enter hostnames1
(Optional) Set source address in IPv6 headersource
(Optional) Set interface to send IPv6 packetinterface
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Enter the port numberi0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4525
T Commandstelnet6
Page 4670
telnet login-attempts{ { telnet login-attempts <d0> } | { no telnet login-attempts [ <d0> ] } }
Syntax Description
Negate a command or set its defaultsno
telnet logintelnet
Set maximum login attemptslogin-attempts
Specify max-attempt numberd0
Command Mode
• /exec/configure/
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4526
T Commandstelnet login-attempts
Page 4671
telnet server enable[no] telnet server enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable telnettelnet
Enable telnetserver
Enable telnetenable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4527
T Commandstelnet server enable
Page 4672
templatetemplate <res-mgr-template-known-name-all>
Syntax Description
Change the template for this vdctemplate
Resource template for this vdcres-mgr-template-known-name-all
Command Mode
• /exec/configure/vdc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4528
T Commandstemplate
Page 4673
template data timeout{ [ no ] template data timeout <time> | no template data timeout }
Syntax Description
Version 9 Templatetemplate
Datadata
Template Data resend timetimeout
Time in secondstime
Command Mode
• /exec/configure/nfm-exporter-v9
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4529
T Commandstemplate data timeout
Page 4674
template peer-policy[no] template peer-policy <peer-policy-template-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Enter template command modetemplate
Template configuration for policy parameterspeer-policy
Name of peer-policy templatepeer-policy-template-name
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4530
T Commandstemplate peer-policy
Page 4675
template peer-session[no] template peer-session <peer-session-template-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Enter template command modetemplate
Template configuration for session parameterspeer-session
Name of peer-session templatepeer-session-template-name
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4531
T Commandstemplate peer-session
Page 4676
template peer[no] template peer <peer-template-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Enter template command modetemplate
Template configuration for peer parameterspeer
Neighbor template namepeer-template-name
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4532
T Commandstemplate peer
Page 4677
terminalterminal { monitor | no { monitor1 | monitor-force } }
Syntax Description
Set terminal line parametersterminal
Copy Syslog output to the current terminal linemonitor
Negate a command or set its defaultsno
Copy Syslog output to the current terminal linemonitor1
Copy Syslog output to the current terminal linemonitor-force
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4533
T Commandsterminal
Page 4678
terminal alias[no] terminal alias [ persist ] [ <alias-name> [ <command> ] ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal line parametersterminal
show aliases (if no arugments) create 'exec' aliases (not persistent).Persistent aliases are in config mode, see 'cli alias
alias
(Optional) add terminal alias to <username>.rc.cli file (auto-execed atlogin time)
persist
(Optional) Name of the alias. (if last argument: shows the value of thatalias) Command lines can start with an alias and it will be expandedbefore parsing. An alias can also be used right after a pipe. Thesubstitution text can contain things like '$1 $2' and those $<number>will be substituted by correspondingly numbered token from thecommand line starting the counting after the alias.
alias-name
(Optional) Value of the alias (what the alias will be substituted with)command
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4534
T Commandsterminal alias
Page 4679
terminal ask-on-term[no] terminal ask-on-term <term>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal line parametersterminal
ask backend driven question on given terminalask-on-term
the terminal (/dev/ptsX)term
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4535
T Commandsterminal ask-on-term
Page 4680
terminal color[no] terminal color [ persist ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal line parametersterminal
enable colorization of prompt(green if last command ok, red if error),command line (blue), output (default color)
color
(Optional) add command to <username>.rc.cli file (auto-execed at logintime)
persist
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4536
T Commandsterminal color
Page 4681
terminal context management[no] terminal context management
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal line parametersterminal
set the vrf contextcontext
vrf context managementmanagement
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4537
T Commandsterminal context management
Page 4682
terminal deep-help[no] terminal deep-help
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal line parametersterminal
enable cli syntax and listdeep-help
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4538
T Commandsterminal deep-help
Page 4683
terminal dont-ask[no] terminal dont-ask [ persist ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal line parametersterminal
Don't ask 'are you sure' questions, take default answer insteaddont-ask
(Optional) add command to <username>.rc.cli file (auto-execed at logintime)
persist
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4539
T Commandsterminal dont-ask
Page 4684
terminal edit-mode vi[no] terminal edit-mode vi [ persist ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal line parametersterminal
set command line edition keys (vi or emacs emacs is default)edit-mode
edit like in vi by default in insert-mode, use ~ for command-modevi
(Optional) add command to <username>.rc.cli file (auto-execed at logintime)
persist
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4540
T Commandsterminal edit-mode vi
Page 4685
terminal event-manager bypassterminal [ <noarg> ] event-manager bypass
Syntax Description
Set terminal line parametersterminal
(Optional)noarg
Event manager cli eventevent-manager
Bypass event manager cli event publishbypass
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4541
T Commandsterminal event-manager bypass
Page 4686
terminal history no-exec-in-config[no] terminal history no-exec-in-config
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal line parametersterminal
configure terminal history propertieshistory
don't recall exec commands while in config modeno-exec-in-config
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4542
T Commandsterminal history no-exec-in-config
Page 4687
terminal history no-exec-in-config[no] terminal history no-exec-in-config
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal line parametersterminal
configure terminal history propertieshistory
don't recall exec commands while in config modeno-exec-in-config
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4543
T Commandsterminal history no-exec-in-config
Page 4688
terminal history no-exec-in-config[no] terminal history no-exec-in-config
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal line parametersterminal
configure terminal history propertieshistory
don't recall exec commands while in config modeno-exec-in-config
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4544
T Commandsterminal history no-exec-in-config
Page 4689
terminal hometerminal home
Syntax Description
Set terminal line parametersterminal
go back to line 1 position 1 without erasing the screen (to be used in clicommand loops)
home
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4545
T Commandsterminal home
Page 4690
terminal lengthterminal length <i0>
Syntax Description
Set terminal line parametersterminal
Set number of lines on a screenlength
Number of lines on screen (0 for no pausing)i0
Command Mode
• /exec/configure/console
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4546
T Commandsterminal length
Page 4691
terminal lengthterminal length <i0>
Syntax Description
Set terminal line parametersterminal
Set number of lines on a screenlength
Number of lines on screen (0 for no pausing)i0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4547
T Commandsterminal length
Page 4692
terminal log-all[no] terminal log-all
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure terminal settingsterminal
Accounting log all commands including the show commandslog-all
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4548
T Commandsterminal log-all
Page 4693
terminal noterminal no { length | terminal-type | width }
Syntax Description
Set terminal line parametersterminal
Negate a command or set its defaultsno
Set number of lines on a screenlength
Set the terminal typeterminal-type
Set width of the display terminalwidth
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4549
T Commandsterminal no
Page 4694
terminal output xml[no] terminal output xml
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal line parametersterminal
how output of show commands should be formatedoutput
xml outputxml
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4550
T Commandsterminal output xml
Page 4695
terminal output xml[no] terminal output xml
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal line parametersterminal
how output of show commands should be formatedoutput
xml outputxml
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4551
T Commandsterminal output xml
Page 4696
terminal output xml[no] terminal output xml <namespace-version>
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal line parametersterminal
how output of show commands should be formatedoutput
xml outputxml
enter the version for xml outputnamespace-version
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4552
T Commandsterminal output xml
Page 4697
terminal passwordterminal password <password> | no terminal password [ <password> ]
Syntax Description
Negate a command or set its defaultsno
Set terminal line parametersterminal
set a password to be used in copy scp/ftp commands use online help onthe argument to disable echo so you don't need to type control-x-e twice(to toggle echo), echo will be re-enabled after carriage-return
password
Enter the password (online help that you just did disabled echo so typeyour password and press return
password
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4553
T Commandsterminal password
Page 4698
terminal prompt[no] terminal prompt [ fix [ <name> ] [ with-cr ] | mode | { fq-command | command } | status | exec-time |time | no-echo ] +
Syntax Description
(Optional) Negate a command or set its defaultsno
Set terminal line parametersterminal
configure how the prompt should look likeprompt
(Optional) set the prompt to a fix name (default _prompt_)fix
(Optional) add a carriage return at the end of the promptwith-cr
(Optional) name to use as a fix promptname
(Optional) include the cli mode name (ex: config-if) into the promtmode
(Optional) include the fully qualified command just executed (formattedlike in accounting log)
fq-command
(Optional) include the previous command (not including the mode andmode instance)
command
(Optional) include the status of previous command (0=success)status
(Optional) include the time it took to execute previous commandexec-time
(Optional) include the time when prompt was printedtime
(Optional) dont echo the typed charactersno-echo
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4554
T Commandsterminal prompt
Page 4699
terminal redirection-modeterminal redirection-mode <mode>
Syntax Description
Set terminal line parametersterminal
Set the redirection moderedirection-mode
mode
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4555
T Commandsterminal redirection-mode
Page 4700
terminal session-timeoutterminal session-timeout <i0>
Syntax Description
Set terminal line parametersterminal
Set session timeoutsession-timeout
Enter timeout in minutes, 0 to disablei0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4556
T Commandsterminal session-timeout
Page 4701
terminal sticky-modeterminal [ <noarg> ] sticky-mode
Syntax Description
Set terminal line parametersterminal
(Optional)noarg
Search for the command match in current mode onlysticky-mode
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4557
T Commandsterminal sticky-mode
Page 4702
terminal terminal-typeterminal terminal-type <s0>
Syntax Description
Set terminal line parametersterminal
Set the terminal typeterminal-type
Terminal types0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4558
T Commandsterminal terminal-type
Page 4703
terminal timeterminal time [ <name> ] [ delta ]
Syntax Description
Set terminal line parametersterminal
save the current time under a variabletime
(Optional) the variable to store the time inname
(Optional) print the delta time to the currently saved time valuedelta
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4559
T Commandsterminal time
Page 4704
terminal tree-updateterminal tree-update
Syntax Description
Set terminal line parametersterminal
Updates the main parse treetree-update
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4560
T Commandsterminal tree-update
Page 4705
terminal verify-onlyterminal [ <noarg> ] verify-only [ username <user> ]
Syntax Description
Set terminal line parametersterminal
(Optional)noarg
Verify command and do not executeverify-only
(Optional) Username for aaa authorizationusername
(Optional) Username for aaa authorizationuser
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4561
T Commandsterminal verify-only
Page 4706
terminal widthterminal width <i0>
Syntax Description
Set terminal line parametersterminal
Set width of the display terminalwidth
Number of characters on a screen linei0
Command Mode
• /exec/configure/console
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4562
T Commandsterminal width
Page 4707
terminal widthterminal width <i0>
Syntax Description
Set terminal line parametersterminal
Set width of the display terminalwidth
Number of characters on a screen linei0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4563
T Commandsterminal width
Page 4708
threshold-percentthreshold-percent { percent-threshold { percentup <up-percentage> [ percentdown<down-percentage> ] |percentdown<down-percentage> [ percentup <up-percentage> ] } } | no threshold-percent { percent-threshold}
Syntax Description
Negate a command or set its defaultsno
Threshold parametersthreshold-percent
Percentage thresholdpercent-threshold
Up thresholdpercentup
Up threshold percentageup-percentage
Command Mode
• /exec/configure/tr-list-thrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4564
T Commandsthreshold-percent
Page 4709
threshold{ { no | default } threshold | threshold <milliseconds> }
Syntax Description
no
Set a command to its defaultsdefault
Operation thresholdthreshold
Millisecond threshold valuemilliseconds
Command Mode
• /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/tcp/exec/configure/ip-sla/icmpEcho /exec/configure/ip-sla/dns /exec/configure/ip-sla/fabricPathEcho/exec/configure/ip-sla/http
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4565
T Commandsthreshold
Page 4710
time-range[no] time-range <name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Define time range entriestime-range
Time range namename
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4566
T Commandstime-range
Page 4711
timeout{ { no | default } timeout |
Syntax Description
no
Set a command to its defaultsdefault
Timeout of an operationtimeout
Command Mode
• /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/tcp/exec/configure/ip-sla/icmpEcho /exec/configure/ip-sla/dns /exec/configure/ip-sla/fabricPathEcho/exec/configure/ip-sla/http
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4567
T Commandstimeout
Page 4712
timeout{ no timeout | timeout <value> }
Syntax Description
no
Inactivity timeout periodtimeout
Session inactivity timeout in seconds (default 900)value
Command Mode
• /exec/configure/config-twamp-ref
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4568
T Commandstimeout
Page 4713
timeout{ timeout <timeout> }
Syntax Description
Specifytimeout
Timeouttimeout
Command Mode
• /exec/configure/configngoamconnectcheck
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4569
T Commandstimeout
Page 4714
timer[no] timer <cap-timer-usec>
Syntax Description
(Optional) Negate the commandno
Configure Packet Drop Timer parameterstimer
cap-timer-usec
Command Mode
• /exec/configure/pkt-drop
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4570
T Commandstimer
Page 4715
timertimer <value> | no timer
Syntax Description
Negate a command or set its defaultsno
Configure Bundle timer valuetimer
Hello timer valuevalue
Command Mode
• /exec/configure/anycast
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4571
T Commandstimer
Page 4716
timer inactivity{ no timer inactivity | timer inactivity <value> }
Syntax Description
no
Timer configurationstimer
Inactivity timerinactivity
Max number of inactive seconds (default 900)value
Command Mode
• /exec/configure/config-twamp-srvr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4572
T Commandstimer inactivity
Page 4717
timers[no] timers { nsf { route-hold <hold-interval> | converge <converge-interval> | signal <signal-interval> } |active-time [ <max-active-time> | disabled ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Set EIGRP timerstimers
EIGRP NSF timernsf
EIGRP hold time for routes learned from nsf peerroute-hold
Secondshold-interval
EIGRP time limit for active stateactive-time
(Optional) EIGRP active-state time limit in minutesmax-active-time
(Optional) disable EIGRP time limit for active statedisabled
EIGRP time limit for convergence after switchoverconverge
Secondsconverge-interval
EIGRP time limit for signaling NSF restartsignal
Secondssignal-interval
Command Mode
• /exec/configure/router-eigrp/router-eigrp-vrf-common /exec/configure/router-eigrp/router-eigrp-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4573
T Commandstimers
Page 4718
timerstimers { <hello-time> { <hold-time> | msec-hold <msec-hold> } | msec-hello <msec-hello> { <hold-time> |msec-hold <msec-hold> } } | no timers
Syntax Description
Negate a command or set its defaultsno
Hello and hold timerstimers
Hello interval in secondshello-time
Hold time in secondshold-time
Specify hold interval in millisecondsmsec-hold
Hold interval in millisecondsmsec-hold
Specify hello interval in millisecondsmsec-hello
Hello interval in millisecondsmsec-hello
Command Mode
• /exec/configure/if-eth-any/hsrp_ipv4 /exec/configure/if-eth-any/hsrp_ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4574
T Commandstimers
Page 4719
timerstimers <keepalive-interval> <hold-time> | { no | default } timers [ <keepalive-interval> <hold-time> ]
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Configure keepalive and hold timerstimers
Keepalive interval (seconds)keepalive-interval
Holdtime (seconds)hold-time
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4575
T Commandstimers
Page 4720
timers advertise[no] timers advertise | timers advertise <val>
Syntax Description
Negate a command or set its defaultsno
Set the VRRP timerstimers
Set the advertise timeradvertise
Advertisement interval in millisecondsval
Command Mode
• /exec/configure/if-eth-any/vrrpv3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4576
T Commandstimers advertise
Page 4721
timers basictimers basic <update> <invalid> <holddown> <garbage> | no timers basic [ <update> <invalid> <holddown><garbage> ]
Syntax Description
Negate a command or set its defaultsno
RIP set timerstimers
RIP set basic timersbasic
RIP update periodupdate
RIP route timeout periodinvalid
RIP route holddown periodholddown
RIP route garbage periodgarbage
Command Mode
• /exec/configure/router-rip/router-rip-af-common /exec/configure/router-rip/router-rip-vrf-af-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4577
T Commandstimers basic
Page 4722
timers bestpath-defer maximum[no] timers bestpath-defer <bestpath-defer-time> maximum <bestpath-defer-time-max>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure bgp related timerstimers
Configure bestpath defer timer value for batch prefix processingbestpath-defer
Bestpath defer time (mseconds)bestpath-defer-time
Configure bestpath defer timer maximum valuemaximum
Maximum bestpath defer time (mseconds)bestpath-defer-time-max
Command Mode
• /exec/configure/router-bgp/router-bgp-af
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4578
T Commandstimers bestpath-defer maximum
Page 4723
timers bestpath-limittimers bestpath-limit <bestpath-timeout> [ always ] | no timers bestpath-limit [ <bestpath-timeout> ]
Syntax Description
Negate a command or set its defaultsno
Configure bgp related timerstimers
Configure timeout for first bestpath after restartbestpath-limit
Bestpath timeout (seconds)bestpath-timeout
(Optional) Configure update-delay-always optionalways
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4579
T Commandstimers bestpath-limit
Page 4724
timers bgp[no] timers bgp <keepalive-interval> <hold-time>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure bgp related timerstimers
Configure different bgp keepalive and holdtimesbgp
Keepalive interval (seconds)keepalive-interval
Holdtime (seconds)hold-time
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4580
T Commandstimers bgp
Page 4725
timers lsa-arrival{ { timers lsa-arrival <interval> } | { no timers lsa-arrival [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure timer related constantstimers
Mimimum interval between arrival of a LSAlsa-arrival
Interval value (milliseconds)interval
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4581
T Commandstimers lsa-arrival
Page 4726
timers lsa-arrival{ { timers lsa-arrival <interval> } | { no timers lsa-arrival [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure timer related constantstimers
Mimimum interval between arrival of a LSAlsa-arrival
Interval value (millisecond)interval
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4582
T Commandstimers lsa-arrival
Page 4727
timers lsa-group-pacing{ { timers lsa-group-pacing <interval> } | { no timers lsa-group-pacing [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure timer related constantstimers
LSA group refresh/maxage intervallsa-group-pacing
Interval value (seconds)interval
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4583
T Commandstimers lsa-group-pacing
Page 4728
timers lsa-group-pacing{ { timers lsa-group-pacing <interval> } | { no timers lsa-group-pacing [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure timer related constantstimers
LSA group refresh/maxage intervallsa-group-pacing
Interval value (seconds)interval
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4584
T Commandstimers lsa-group-pacing
Page 4729
timers prefix-peer-timeouttimers prefix-peer-timeout <prefixpeer-timeout> | no timers prefix-peer-timeout [ <prefixpeer-timeout> ]
Syntax Description
Negate a command or set its defaultsno
Configure bgp related timerstimers
Configure how long state for a prefix peer is maintainedprefix-peer-timeout
Prefix Peer timeout (seconds)prefixpeer-timeout
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4585
T Commandstimers prefix-peer-timeout
Page 4730
timers prefix-peer-waittimers prefix-peer-wait <prefixpeer-wait> | no timers prefix-peer-wait [ <prefixpeer-wait> ]
Syntax Description
Negate a command or set its defaultsno
Configure bgp related timerstimers
Configure wait timer for a prefix peerprefix-peer-wait
Prefix peer wait timer (seconds)prefixpeer-wait
Command Mode
• /exec/configure/router-bgp/vrf-cmds
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4586
T Commandstimers prefix-peer-wait
Page 4731
timers srgb cleanup{ { timers srgb cleanup <interval> } | { no timers srgb cleanup [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure timer related constantstimers
Configure SRGB related timer constantssrgb
Interval for which SR will wait for SRGB cleanup ACK from clientscleanup
Interval value (seconds)interval
Command Mode
• /exec/configure/config-sr-mpls
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4587
T Commandstimers srgb cleanup
Page 4732
timers srgb retry{ { timers srgb retry <interval> } | { no timers srgb retry [ <interval> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure timer related constantstimers
Configure SRGB related timer constantssrgb
Interval for which SR will retry SRGB allocation with ULIBretry
Interval value (seconds)interval
Command Mode
• /exec/configure/config-sr-mpls
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4588
T Commandstimers srgb retry
Page 4733
timers throttle lsa{ { timers throttle lsa <start-time> <hold-time> <max-time> } | { no timers throttle lsa [ <start-time><hold-time> <max-time> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure timer related constantstimers
Set rate-limiting values (milliseconds)throttle
Set rate-limiting for LSA generationlsa
Start interval (milliseconds)start-time
Hold interval (milliseconds)hold-time
Max interval (milliseconds)max-time
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4589
T Commandstimers throttle lsa
Page 4734
timers throttle lsa{ { timers throttle lsa <start-time> <hold-time> <max-time> } | { no timers throttle lsa [ <start-time><hold-time> <max-time> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure timer related constantstimers
Set rate-limiting values (milliseconds)throttle
Set rate-limiting for LSA generationlsa
Start interval (milliseconds)start-time
Hold interval (milliseconds)hold-time
Max interval (milliseconds)max-time
Command Mode
• /exec/configure/router-ospf3 /exec/configure/router-ospf3/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4590
T Commandstimers throttle lsa
Page 4735
timers throttle spf{ { timers throttle spf <start-time> <hold-time> <max-time> } | { no timers throttle spf [ <start-time><hold-time> <max-time> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure timer related constantstimers
Configure timer related constantsthrottle
OSPF SPF timersspf
Initial SPF schedule delay in millisecondsstart-time
Minimum hold time between SPF calculationshold-time
Maximum wait time between SPF calculationsmax-time
Command Mode
• /exec/configure/router-ospf3/router-ospf3-af-ipv6 /exec/configure/router-ospf3/vrf/router-ospf3-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4591
T Commandstimers throttle spf
Page 4736
timers throttle spf{ { timers throttle spf <start-time> <hold-time> <max-time> } | { no timers throttle spf [ <start-time><hold-time> <max-time> ] } }
Syntax Description
Negate a command or set its defaultsno
Configure timer related constantstimers
Configure timer related constantsthrottle
OSPF SPF timersspf
Initial SPF schedule delay in millisecondsstart-time
Minimum hold time between SPF calculationshold-time
Maximum wait time between SPF calculationsmax-time
Command Mode
• /exec/configure/router-ospf /exec/configure/router-ospf/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4592
T Commandstimers throttle spf
Page 4737
timestamp timestamptimestamp { ingress id <ingress-source-id> | egress id <egress-source-id> } | timestamp { ingress id<ingress-source-id> egress id <egress-source-id> } | no timestamp
Syntax Description
Negate a command or set its defaultsno
Configure packet timestampingtimestamp
ingress directioningress
egress directionegress
source identifier inserted in timestampid
Ingress source id valueingress-source-id
Egress source id valueegress-source-id
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4593
T Commandstimestamp timestamp
Page 4738
tls trust-point local remotetls trust-point local <tp_local> remote <tp_remote> | no tls trust-point
Syntax Description
Negate a command or set its defaultsno
OpenFlow switch tlstls
Configure local and remote trustpointstrust-point
Configure local trustpointlocal
Local trustpoint nametp_local
Configure remote trustpointremote
Remote trustpoint nametp_remote
Command Mode
• /exec/configure/openflow/switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4594
T Commandstls trust-point local remote
Page 4739
tls trust-point local remotetls trust-point local <tp_local> remote <tp_remote> | no tls trust-point
Syntax Description
Negate a command or set its defaultsno
OpenFlow switch tlstls
Configure local and remote trustpointstrust-point
Configure local trustpointlocal
Local trustpoint nametp_local
Configure remote trustpointremote
Remote trustpoint nametp_remote
Command Mode
• /exec/configure/openflow/switch/sub-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4595
T Commandstls trust-point local remote
Page 4740
topology[no] topology <tpg-id>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Layer-2 Topology for IS-IStopology
L2 Topology ID 1-63tpg-id
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4596
T Commandstopology
Page 4741
topology holddown sigerr[no] topology holddown sigerr | topology holddown sigerr <sec>
Syntax Description
Negate a command or set its defaultsno
Topology Database Configurationtopology
Topology Database hold down timersholddown
Link hold down time for signalling errorssigerr
Hold down time in secondssec
Command Mode
• /exec/configure/te
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4597
T Commandstopology holddown sigerr
Page 4742
tos{ { no | default } tos | tos <tos-value> }
Syntax Description
no
Set a command to its defaultsdefault
Type of Servicetos
Type of Service Valuetos-value
Command Mode
• /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/tcp/exec/configure/ip-sla/icmpEcho /exec/configure/ip-sla/http
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4598
T Commandstos
Page 4743
tr| tr [ -c | -d | -s | -t ] + <SET1> [ <SET2> ]
Syntax Description
Pipe command output to filter|
Translate, squeeze, and/or delete characterstr
(Optional) first complement SET1-c
(Optional) delete characters in SET1, do not translate-d
(Optional) replace each sequence of a repeated character from SET1with single occurrence of that character
-s
(Optional) first truncate SET1 to length of SET2-t
character SET1: CHAR1-CHAR2 = all characters from CHAR1 toCHAR2 in ascending order special chars: (tab) (new line) [:alnum:][:alpha:] [:digit:] [:graph:] (printable, no space) [:print:] (printable, withspace) [:lower:] [:upper:] [:space:] (tab or space)
SET1
(Optional) character SET2 (for translation length is extended to lengthof SET1 by repeating last char, excess chars are ignored): format sameas SET1 [CHAR*] = copies of CHAR until length of SET1[CHAR*REPEAT] = REPEAT copies of CHAR
SET2
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4599
T Commandstr
Page 4744
trace buffer sizetrace buffer { error | warning | event } size <size>
Syntax Description
MPLS static tracetrace
MPLS static trace bufferbuffer
MPLS static error traceerror
MPLS static warning tracewarning
MPLS static event traceevent
trace buffer size in Kbytessize
trace buffer size in Kbytessize
Command Mode
• /exec/configure/mpls_static
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4600
T Commandstrace buffer size
Page 4745
traceroutetraceroute { <host> | <hostname> } [ port <portnumber> ] [ [ source-interface <src-intf> ] | [ [ source { <host>| <hostname> | <interface> } ] [ vrf { <vrf-name> | <vrf-known-name> } ] ] ]
Syntax Description
Traceroutetraceroute
IP address of remote systemhost
Hostname of remote systemhostname
(Optional) Set destination portport
(Optional) Enter destination port numberportnumber
(Optional) Set source address in IP headersource
(Optional) Interfaceinterface
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Select source interfacesource-interface
(Optional) Specify interfacesrc-intf
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4601
T Commandstraceroute
Page 4746
traceroute6traceroute6 { <host> | <hostname> } [ [ [ source { <host> | <hostname> | <interface> } ] [ vrf { <vrf-name>| <vrf-known-name> } ] ] | [ source-interface <src-intf> ] ]
Syntax Description
Traceroute6traceroute6
Hostname of remote systemhostname
(Optional) Set source address in IPv6 headersource
(Optional) Interfaceinterface
(Optional) Display per-VRF informationvrf
(Optional) VRF namevrf-name
(Optional) Known VRF namevrf-known-name
(Optional) Select source interfacesource-interface
(Optional) Specify interfacesrc-intf
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4602
T Commandstraceroute6
Page 4747
track-adjacency-nexthop[no] track-adjacency-nexthop
Syntax Description
(Optional) Negate a command or set its defaultsno
Track next-hop for same-site Overlay adjacenciestrack-adjacency-nexthop
Command Mode
• /exec/configure/otv-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4603
T Commandstrack-adjacency-nexthop
Page 4748
tracktrack <object-id> { list threshold <weight-val> }
Syntax Description
Object tracking configuration commandtrack
Tracked Objectobject-id
Object tracking listlist
threshold typethreshold
threshold weight typeweight-val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4604
T Commandstrack
Page 4749
track[no] track <object-number> [ decrement <value> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Associates track object to HSRP grouptrack
Set the object number to the groupobject-number
(Optional) Decrements when tracked object goes downdecrement
(Optional) Set the value to decrement from priorityvalue
Command Mode
• /exec/configure/if-eth-any/hsrp_ipv4 /exec/configure/if-eth-any/hsrp_ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4605
T Commandstrack
Page 4750
tracktrack <object-number> | no track
Syntax Description
Negate a command or set its defaultsno
Associates track object to Anycast Bundletrack
Set the object numberobject-number
Command Mode
• /exec/configure/anycast
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4606
T Commandstrack
Page 4751
tracktrack <object-id>
Syntax Description
Object tracking deletion commandtrack
Tracked Objectobject-id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4607
T Commandstrack
Page 4752
track[no] track <object-id> [ force ]
Syntax Description
Negate a command or set its defaultsno
Object tracking deletion commandtrack
Tracked Objectobject-id
(Optional) Completely remove the objectforce
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4608
T Commandstrack
Page 4753
tracktrack <object-id> { { ip_v4 route <route-prefix> reachability [ hmm ] } | { ip_v6 routev6 <v6route-prefix>reachability [ hmm ] } }
Syntax Description
Object tracking configuration commandtrack
Tracked Objectobject-id
IPv4 protocolip_v4
IPv4 routeroute
Specify ipv4 route prefixroute-prefix
IPv6 protocolip_v6
IPv6 routeroutev6
Route reachability statereachability
(Optional) Track routes owned by hmmhmm
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4609
T Commandstrack
Page 4754
tracktrack <object-id> { ip_v4 sla <sla-id> [ sla_reachability | sla_state ] }
Syntax Description
Object tracking configuration commandtrack
Tracked Objectobject-id
IPv4 protocolip_v4
IP Service Level Agreementsla
Entry numbersla-id
(Optional) Reachabilitysla_reachability
(Optional) return code statesla_state
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4610
T Commandstrack
Page 4755
tracktrack <object-id> { list { boolean <bool-val> } }
Syntax Description
Object tracking configuration commandtrack
Tracked Objectobject-id
Object tracking listlist
boolean list typeboolean
boolean list typebool-val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4611
T Commandstrack
Page 4756
tracktrack <object-id> { list threshold <percentage-val> }
Syntax Description
Object tracking configuration commandtrack
Tracked Objectobject-id
Object tracking listlist
threshold typethreshold
threshold percentage typepercentage-val
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4612
T Commandstrack
Page 4757
tracktrack <track-obj> | no track <track-obj>
Syntax Description
Negate a command or set its defaultsno
Tracking object to suspend vPC if object goes downtrack
Tracked objecttrack-obj
Command Mode
• /exec/configure/vpc-domain
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4613
T Commandstrack
Page 4758
track data[no] track data <loc-uri>
Syntax Description
(Optional) Negate a command or set its defaultsno
User files to preservedata
Track file uritrack
Enter file uriloc-uri
Command Mode
• /exec/configure/personality
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4614
T Commandstrack data
Page 4759
track interfacetrack <object-id> interface <ifnum> { line-protocol | ipv4 routing | ipv6 routingv6 }
Syntax Description
Object tracking configuration commandstrack
Tracked Objectobject-id
Interface to trackinterface
Interface type and numberifnum
Track interface line-protocolline-protocol
IPv4 parametersipv4
Track interface ipv4 routingrouting
IPv6 parametersipv6
Track interface ipv6 routingroutingv6
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4615
T Commandstrack interface
Page 4760
track interface priority{ { track { { interface <intf_num> priority <priority_value> } | { <object-num> [ decrement <decrement-value>] } } } | { no track [ { { interface <intf_num> priority <priority_value> } | { <object-num> [ decrement<decrement-value> ] } } ] } }
Syntax Description
Negate a command or set its defaultsno
Track the availability of another interface/objecttrack
Select the tracked interface(Native tracking)interface
intf_num
Vr priority used when the tracked interface is downpriority
priority_value
Set the object number to the group(Object tracking)object-num
(Optional) Decrements priority when tracked object goes downdecrement
(Optional) Set the value to decrement from prioritydecrement-value
Command Mode
• /exec/configure/if-eth-any/vrrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4616
T Commandstrack interface priority
Page 4761
track running-state track startup-state[no] track running-state | [ no ] track startup-state
Syntax Description
(Optional) Negate a command or set its defaultsno
Track file uritrack
active patches, third-party RPMs, and running-configrunning-state
committed patches, third-party RPMs, and startup-configstartup-state
Command Mode
• /exec/configure/personality
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4617
T Commandstrack running-state track startup-state
Page 4762
tracking enable[no] tracking { enable [ reachable-lifetime { <reach_secs> | infinite } ] | disable [ stale-lifetime { <stale_secs>| infinite } ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Secondsreach_secs
(Optional) Secondsstale_secs
(Optional) Keep entry in chosen state foreverinfinite
Command Mode
• /exec/configure/config-snoop-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4618
T Commandstracking enable
Page 4763
traffic-class{ { no | default } traffic-class | traffic-class <traffic-class> }
Syntax Description
no
Set a command to its defaultsdefault
Traffic Classtraffic-class
Traffic Class Valuetraffic-class
Command Mode
• /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/tcp/exec/configure/ip-sla/icmpEcho /exec/configure/ip-sla/http
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4619
T Commandstraffic-class
Page 4764
traffic-engineering[no] traffic-engineering
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Traffic Engineering related configurationstraffic-engineering
Command Mode
• /exec/configure/sr
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4620
T Commandstraffic-engineering
Page 4765
transmit-delay{ { transmit-delay <delay> } | { no transmit-delay [ <delay> ] } }
Syntax Description
Negate a command or set its defaultsno
Packet transmission delaytransmit-delay
(seconds)delay
Command Mode
• /exec/configure/router-ospf3/router-ospf3-vlink /exec/configure/router-ospf3/vrf/router-ospf3-vlink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4621
T Commandstransmit-delay
Page 4766
transmit-delay{ { transmit-delay <delay> } | { no transmit-delay [ <delay> ] } }
Syntax Description
Negate a command or set its defaultsno
Packet transmission delaytransmit-delay
(seconds)delay
Command Mode
• /exec/configure/router-ospf/router-ospf-vlink /exec/configure/router-ospf/vrf/router-ospf-vlink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4622
T Commandstransmit-delay
Page 4767
transmit-delay{ { transmit-delay <delay> } | { no transmit-delay [ <delay> ] } }
Syntax Description
Negate a command or set its defaultsno
Packet transmission delaytransmit-delay
(seconds)delay
Command Mode
• /exec/configure/router-ospf/vrf/router-ospf-slink
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4623
T Commandstransmit-delay
Page 4768
transport connection-mode passive[ no | default ] transport connection-mode passive
Syntax Description
(Optional) Negate a command or set its defaultsno
(Optional) Inherit values from a peer templatedefault
BGP transport connectiontransport
Specify type of connectionconnection-mode
Allow passive connection setup onlypassive
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor /exec/configure/router-bgp/router-bgp-neighbor-stmp/exec/configure/router-bgp/router-bgp-vrf-neighbor/exec/configure/router-bgp/router-bgp-template-neighbor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4624
T Commandstransport connection-mode passive
Page 4769
transport email{ transport email { from <s0> | reply-to <s1> | smtp-server { <hostipv4> | <hostipv6> | <hostname> } [ port<i1> ] [ use-vrf <s2> ] } | no transport email smtp-server | no transport email { from | reply-to } }
Syntax Description
Negate a command or set its defaultsno
Configure transport related configurationtransport
Configure email transport related configurationemail
Configure from email addressfrom
Provide from email address, example: [email protected]
Configure replyto email addressreply-to
Provide reply-to email address, example: [email protected]
Configure SMTP server addresssmtp-server
SMTP server(DNS name or IPv4 or IPv6 address)hostname
IPV4 address of SMTP serverhostipv4
(Optional) Configure SMTP server port (default:25)port
(Optional) SMTP server porti1
(Optional) Configure vrf nameuse-vrf
(Optional) vrf names2
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4625
T Commandstransport email
Page 4770
transport email mail-server{ [ no ] transport email mail-server { <hostipv4> | <hostipv6> | <hostname> } [ port <i1> ] [ priority <i2> ][ use-vrf <s2> ] }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure transport related configurationtransport
Configure email transport related configurationemail
Configure SMTP server address (for supportingmultiple SMTP-servers)mail-server
SMTP server(DNS name or IPv4 or IPv6 address)hostname
IPV4 address of SMTP serverhostipv4
(Optional) Configure SMTP server port (default:25)port
(Optional) SMTP server porti1
(Optional) Configure vrf nameuse-vrf
(Optional) vrf names2
(Optional) Configure SMTP server priority (1-100) (default:50)priority
(Optional) SMTP server priorityi2
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4626
T Commandstransport email mail-server
Page 4771
transport http proxy enable[no] transport http proxy enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure transport related configurationtransport
Configure transport option for http urlshttp
Configure proxy for http transportproxy
Enable the usage of proxy server for messages sent over http(s)enable
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4627
T Commandstransport http proxy enable
Page 4772
transport http proxy server{ transport http proxy server { <hostname> } [ port <i1> ] } | { no transport http proxy server }
Syntax Description
Negate a command or set its defaultsno
Configure transport related configurationtransport
Configure transport option for http urlshttp
Configure proxy for http transportproxy
Configure proxy server address and portserver
Proxy server name or IP address(DNS name or IPv4 or IPv6 address)hostname
(Optional) Configure Proxy server port (default:8080)port
(Optional) Proxy server porti1
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4628
T Commandstransport http proxy server
Page 4773
transport http use-vrftransport http use-vrf <s2> | no transport http use-vrf
Syntax Description
Negate a command or set its defaultsno
Configure transport related configurationtransport
Configure transport option for http urlshttp
Configure vrf nameuse-vrf
vrf names2
Command Mode
• /exec/configure/callhome
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4629
T Commandstransport http use-vrf
Page 4774
transport udp[no] transport udp { src-port <srcport> dst-port <dstport> | dst-port <dstport> src-port <srcport> | src-port<srcport> | dst-port <dstport> }
Syntax Description
Transport configurationstransport
UDP Portudp
Src UDP portsrc-port
UDP port to be configured, default 49153srcport
Dest UDP portdst-port
UDP port to be configured for destination, default 49153dstport
Command Mode
• /exec/configure/config-ssx-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4630
T Commandstransport udp
Page 4775
transport udp{ [ no ] transport udp <portnumber> | no transport udp }
Syntax Description
Transport Destination Porttransport
Destination UDP Portudp
Destination UDP Portportnumber
Command Mode
• /exec/configure/config-int-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4631
T Commandstransport udp
Page 4776
transport udp{ [ no ] transport udp <portnumber> | no transport udp }
Syntax Description
Transport Destination Porttransport
Destination UDP Portudp
Destination UDP Portportnumber
Command Mode
• /exec/configure/nfm-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4632
T Commandstransport udp
Page 4777
transport udp source-port{ [ no ] transport udp source-port <intf> }
Syntax Description
Transport protocol configtransport
UDP Portudp
source-portsource-port
UDP port to be configuredintf
Command Mode
• /exec/configure/config-fte-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4633
T Commandstransport udp source-port
Page 4778
trigger forwarding distribution moduletrigger forwarding distribution module <module>
Syntax Description
Triggertrigger
Trigger related to forwardingforwarding
Trigger distribution of forwarding data to LCsdistribution
distribute to a particular modulemodule
module numbermodule
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4634
T Commandstrigger forwarding distribution module
Page 4779
trigger inittrigger init [ asic <asic-no> ] [ slice <slice-no> ] [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4635
T Commandstrigger init
Page 4780
trigger init in-select 10trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 10 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
{outer l4, inner l4, ieth}10
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4636
T Commandstrigger init in-select 10
Page 4781
trigger init in-select 10 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 10 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{outer l4, inner l4, ieth}10
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4637
T Commandstrigger init in-select 10 out-select 0
Page 4782
trigger init in-select 10 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 10 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{outer l4, inner l4, ieth}10
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4638
T Commandstrigger init in-select 10 out-select 1
Page 4783
trigger init in-select 10 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 10 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{outer l4, inner l4, ieth}10
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4639
T Commandstrigger init in-select 10 out-select 2
Page 4784
trigger init in-select 19trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 19 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
{udf_vec}19
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4640
T Commandstrigger init in-select 19
Page 4785
trigger init in-select 19 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 19 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{udf_vec}19
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4641
T Commandstrigger init in-select 19 out-select 0
Page 4786
trigger init in-select 19 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 19 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{udf_vec}19
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4642
T Commandstrigger init in-select 19 out-select 1
Page 4787
trigger init in-select 19 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 19 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{udf_vec}19
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4643
T Commandstrigger init in-select 19 out-select 2
Page 4788
trigger init in-select 6trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 6 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
{outer l2, outer l3, outer l4}6
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4644
T Commandstrigger init in-select 6
Page 4789
trigger init in-select 6 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 6 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{outer l2, outer l3, outer l4}6
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4645
T Commandstrigger init in-select 6 out-select 0
Page 4790
trigger init in-select 6 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 6 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{outer l2, outer l3, outer l4}6
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4646
T Commandstrigger init in-select 6 out-select 1
Page 4791
trigger init in-select 6 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 6 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{outer l2, outer l3, outer l4}6
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4647
T Commandstrigger init in-select 6 out-select 2
Page 4792
trigger init in-select 7trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 7 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
{inner l2, inner l3, inner l4}7
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4648
T Commandstrigger init in-select 7
Page 4793
trigger init in-select 7 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 7 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{inner l2, inner l3, inner l4}7
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4649
T Commandstrigger init in-select 7 out-select 0
Page 4794
trigger init in-select 7 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 7 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{inner l2, inner l3, inner l4}7
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4650
T Commandstrigger init in-select 7 out-select 1
Page 4795
trigger init in-select 7 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 7 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{inner l2, inner l3, inner l4}7
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4651
T Commandstrigger init in-select 7 out-select 2
Page 4796
trigger init in-select 8trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 8 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
{outer l2, inner l2, ieth}8
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4652
T Commandstrigger init in-select 8
Page 4797
trigger init in-select 8 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 8 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{outer l2, inner l2, ieth}8
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4653
T Commandstrigger init in-select 8 out-select 0
Page 4798
trigger init in-select 8 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 8 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{outer l2, inner l2, ieth}8
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4654
T Commandstrigger init in-select 8 out-select 1
Page 4799
trigger init in-select 8 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 8 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{outer l2, inner l2, ieth}8
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4655
T Commandstrigger init in-select 8 out-select 2
Page 4800
trigger init in-select 9trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 9 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
{outer l3, inner l3}9
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4656
T Commandstrigger init in-select 9
Page 4801
trigger init in-select 9 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 9 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{outer l3, inner l3}9
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4657
T Commandstrigger init in-select 9 out-select 0
Page 4802
trigger init in-select 9 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 9 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{outer l3, inner l3}9
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4658
T Commandstrigger init in-select 9 out-select 1
Page 4803
trigger init in-select 9 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] in-select 9 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
in-selectin-select
out-selectout-select
{outer l3, inner l3}9
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4659
T Commandstrigger init in-select 9 out-select 2
Page 4804
trigger init ingress in-select 3 out-select 0trigger init { ingress | egress } in-select 3 out-select 0
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pktrw0
outerl2-outerl3-outerl43
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4660
T Commandstrigger init ingress in-select 3 out-select 0
Page 4805
trigger init ingress in-select 3 out-select 03trigger init { ingress | egress } in-select 3 out-select 03
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_lsb03
outerl2-outerl3-outerl43
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4661
T Commandstrigger init ingress in-select 3 out-select 03
Page 4806
trigger init ingress in-select 3 out-select 0 reversetrigger init { ingress | egress } in-select 3 out-select 0 reverse
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pktrw0
outerl2-outerl3-outerl43
Program reverse ELAMreverse
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4662
T Commandstrigger init ingress in-select 3 out-select 0 reverse
Page 4807
trigger init ingress in-select 3 out-select 1trigger init { ingress | egress } in-select 3 out-select 1
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_fifo_lsb1
outerl2-outerl3-outerl43
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4663
T Commandstrigger init ingress in-select 3 out-select 1
Page 4808
trigger init ingress in-select 3 out-select 2trigger init { ingress | egress } in-select 3 out-select 2
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_fifo_msb2
outerl2-outerl3-outerl43
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4664
T Commandstrigger init ingress in-select 3 out-select 2
Page 4809
trigger init ingress in-select 3 out-select 4trigger init { ingress | egress } in-select 3 out-select 4
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_msb4
outerl2-outerl3-outerl43
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4665
T Commandstrigger init ingress in-select 3 out-select 4
Page 4810
trigger init ingress in-select 3 out-select 5trigger init { ingress | egress } in-select 3 out-select 5
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
sideband5
outerl2-outerl3-outerl43
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4666
T Commandstrigger init ingress in-select 3 out-select 5
Page 4811
trigger init ingress in-select 3 out-select 5 reversetrigger init { ingress | egress } in-select 3 out-select 5 reverse
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
sideband5
outerl2-outerl3-outerl43
Program reverse ELAMreverse
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4667
T Commandstrigger init ingress in-select 3 out-select 5 reverse
Page 4812
trigger init ingress in-select 4 out-select 0trigger init { ingress | egress } in-select 4 out-select 0
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pktrw0
innerl2-innerl3-innerl44
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4668
T Commandstrigger init ingress in-select 4 out-select 0
Page 4813
trigger init ingress in-select 4 out-select 04trigger init { ingress | egress } in-select 4 out-select 04
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_msb04
innerl2-innerl3-innerl44
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4669
T Commandstrigger init ingress in-select 4 out-select 04
Page 4814
trigger init ingress in-select 4 out-select 0 reversetrigger init { ingress | egress } in-select 4 out-select 0 reverse
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pktrw0
innerl2-innerl3-innerl44
Program reverse ELAMreverse
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4670
T Commandstrigger init ingress in-select 4 out-select 0 reverse
Page 4815
trigger init ingress in-select 4 out-select 1trigger init { ingress | egress } in-select 4 out-select 1
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_fifo_lsb1
innerl2-innerl3-innerl44
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4671
T Commandstrigger init ingress in-select 4 out-select 1
Page 4816
trigger init ingress in-select 4 out-select 2trigger init { ingress | egress } in-select 4 out-select 2
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_fifo_msb2
innerl2-innerl3-innerl44
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4672
T Commandstrigger init ingress in-select 4 out-select 2
Page 4817
trigger init ingress in-select 4 out-select 3trigger init { ingress | egress } in-select 4 out-select 3
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_lsb3
innerl2-innerl3-innerl44
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4673
T Commandstrigger init ingress in-select 4 out-select 3
Page 4818
trigger init ingress in-select 4 out-select 5trigger init { ingress | egress } in-select 4 out-select 5
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
sideband5
innerl2-innerl3-innerl44
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4674
T Commandstrigger init ingress in-select 4 out-select 5
Page 4819
trigger init ingress in-select 4 out-select 5 reversetrigger init { ingress | egress } in-select 4 out-select 5 reverse
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
sideband5
innerl2-innerl3-innerl44
Program reverse ELAMreverse
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4675
T Commandstrigger init ingress in-select 4 out-select 5 reverse
Page 4820
trigger init ingress in-select 5 out-select 0trigger init { ingress | egress } in-select 5 out-select 0
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pktrw0
outerl2-innerl25
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4676
T Commandstrigger init ingress in-select 5 out-select 0
Page 4821
trigger init ingress in-select 5 out-select 05trigger init { ingress | egress } in-select 5 out-select 05
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
sideband05
outerl2-innerl25
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4677
T Commandstrigger init ingress in-select 5 out-select 05
Page 4822
trigger init ingress in-select 5 out-select 05 reversetrigger init { ingress | egress } in-select 5 out-select 05 reverse
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
sideband05
outerl2-innerl25
Program reverse ELAMreverse
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4678
T Commandstrigger init ingress in-select 5 out-select 05 reverse
Page 4823
trigger init ingress in-select 5 out-select 0 reversetrigger init { ingress | egress } in-select 5 out-select 0 reverse
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pktrw0
outerl2-innerl25
Program reverse ELAMreverse
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4679
T Commandstrigger init ingress in-select 5 out-select 0 reverse
Page 4824
trigger init ingress in-select 5 out-select 1trigger init { ingress | egress } in-select 5 out-select 1
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_fifo_lsb1
outerl2-innerl25
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4680
T Commandstrigger init ingress in-select 5 out-select 1
Page 4825
trigger init ingress in-select 5 out-select 2trigger init { ingress | egress } in-select 5 out-select 2
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_fifo_msb2
outerl2-innerl25
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4681
T Commandstrigger init ingress in-select 5 out-select 2
Page 4826
trigger init ingress in-select 5 out-select 3trigger init { ingress | egress } in-select 5 out-select 3
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_lsb3
outerl2-innerl25
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4682
T Commandstrigger init ingress in-select 5 out-select 3
Page 4827
trigger init ingress in-select 5 out-select 4trigger init { ingress | egress } in-select 5 out-select 4
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_msb4
outerl2-innerl25
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4683
T Commandstrigger init ingress in-select 5 out-select 4
Page 4828
trigger init ingress in-select 6 out-select 0trigger init { ingress | egress } in-select 6 out-select 0
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pktrw0
outerl3-innerl36
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4684
T Commandstrigger init ingress in-select 6 out-select 0
Page 4829
trigger init ingress in-select 6 out-select 0 reversetrigger init { ingress | egress } in-select 6 out-select 0 reverse
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pktrw0
outerl3-innerl36
Program reverse ELAMreverse
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4685
T Commandstrigger init ingress in-select 6 out-select 0 reverse
Page 4830
trigger init ingress in-select 6 out-select 1trigger init { ingress | egress } in-select 6 out-select 1
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_fifo_lsb1
outerl3-innerl36
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4686
T Commandstrigger init ingress in-select 6 out-select 1
Page 4831
trigger init ingress in-select 6 out-select 2trigger init { ingress | egress } in-select 6 out-select 2
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_fifo_msb2
outerl3-innerl36
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4687
T Commandstrigger init ingress in-select 6 out-select 2
Page 4832
trigger init ingress in-select 6 out-select 3trigger init { ingress | egress } in-select 6 out-select 3
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_lsb3
outerl3-innerl36
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4688
T Commandstrigger init ingress in-select 6 out-select 3
Page 4833
trigger init ingress in-select 6 out-select 4trigger init { ingress | egress } in-select 6 out-select 4
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_msb4
outerl3-innerl36
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4689
T Commandstrigger init ingress in-select 6 out-select 4
Page 4834
trigger init ingress in-select 6 out-select 5trigger init { ingress | egress } in-select 6 out-select 5
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
sideband5
outerl3-innerl36
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4690
T Commandstrigger init ingress in-select 6 out-select 5
Page 4835
trigger init ingress in-select 6 out-select 5 reversetrigger init { ingress | egress } in-select 6 out-select 5 reverse
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
sideband5
outerl3-innerl36
Program reverse ELAMreverse
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4691
T Commandstrigger init ingress in-select 6 out-select 5 reverse
Page 4836
trigger init ingress in-select 7 out-select 0trigger init { ingress | egress } in-select 7 out-select 0
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pktrw0
outerl4-innerl47
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4692
T Commandstrigger init ingress in-select 7 out-select 0
Page 4837
trigger init ingress in-select 7 out-select 0 reversetrigger init { ingress | egress } in-select 7 out-select 0 reverse
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pktrw0
outerl4-innerl47
Program reverse ELAMreverse
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4693
T Commandstrigger init ingress in-select 7 out-select 0 reverse
Page 4838
trigger init ingress in-select 7 out-select 1trigger init { ingress | egress } in-select 7 out-select 1
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_fifo_lsb1
outerl4-innerl47
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4694
T Commandstrigger init ingress in-select 7 out-select 1
Page 4839
trigger init ingress in-select 7 out-select 2trigger init { ingress | egress } in-select 7 out-select 2
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_fifo_msb2
outerl4-innerl47
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4695
T Commandstrigger init ingress in-select 7 out-select 2
Page 4840
trigger init ingress in-select 7 out-select 3trigger init { ingress | egress } in-select 7 out-select 3
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_lsb3
outerl4-innerl47
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4696
T Commandstrigger init ingress in-select 7 out-select 3
Page 4841
trigger init ingress in-select 7 out-select 4trigger init { ingress | egress } in-select 7 out-select 4
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
pkt_msb4
outerl4-innerl47
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4697
T Commandstrigger init ingress in-select 7 out-select 4
Page 4842
trigger init ingress in-select 7 out-select 5trigger init { ingress | egress } in-select 7 out-select 5
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
sideband5
outerl4-innerl47
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4698
T Commandstrigger init ingress in-select 7 out-select 5
Page 4843
trigger init ingress in-select 7 out-select 5 reversetrigger init { ingress | egress } in-select 7 out-select 5 reverse
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
Ingress Fieldsingress
Egress Fieldsegress
in-selectin-select
out-selectout-select
sideband5
outerl4-innerl47
Program reverse ELAMreverse
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4699
T Commandstrigger init ingress in-select 7 out-select 5 reverse
Page 4844
trigger init lu-a2d 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4700
T Commandstrigger init lu-a2d 0
Page 4845
trigger init lu-a2d 0 in-select 10 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 10 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{outer l4, inner l4, ieth}10
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4701
T Commandstrigger init lu-a2d 0 in-select 10 out-select 0
Page 4846
trigger init lu-a2d 0 in-select 10 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 10 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{outer l4, inner l4, ieth}10
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4702
T Commandstrigger init lu-a2d 0 in-select 10 out-select 1
Page 4847
trigger init lu-a2d 0 in-select 10 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 10 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{outer l4, inner l4, ieth}10
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4703
T Commandstrigger init lu-a2d 0 in-select 10 out-select 2
Page 4848
trigger init lu-a2d 0 in-select 19 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 19 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{udf_vec}19
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4704
T Commandstrigger init lu-a2d 0 in-select 19 out-select 0
Page 4849
trigger init lu-a2d 0 in-select 19 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 19 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{udf_vec}19
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4705
T Commandstrigger init lu-a2d 0 in-select 19 out-select 1
Page 4850
trigger init lu-a2d 0 in-select 19 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 19 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{udf_vec}19
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4706
T Commandstrigger init lu-a2d 0 in-select 19 out-select 2
Page 4851
trigger init lu-a2d 0 in-select 6 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 6 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{outer l2, outer l3, outer l4}6
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4707
T Commandstrigger init lu-a2d 0 in-select 6 out-select 0
Page 4852
trigger init lu-a2d 0 in-select 6 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 6 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{outer l2, outer l3, outer l4}6
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4708
T Commandstrigger init lu-a2d 0 in-select 6 out-select 1
Page 4853
trigger init lu-a2d 0 in-select 6 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 6 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{outer l2, outer l3, outer l4}6
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4709
T Commandstrigger init lu-a2d 0 in-select 6 out-select 2
Page 4854
trigger init lu-a2d 0 in-select 7 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 7 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{inner l2, inner l3, inner l4}7
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4710
T Commandstrigger init lu-a2d 0 in-select 7 out-select 0
Page 4855
trigger init lu-a2d 0 in-select 7 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 7 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{inner l2, inner l3, inner l4}7
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4711
T Commandstrigger init lu-a2d 0 in-select 7 out-select 1
Page 4856
trigger init lu-a2d 0 in-select 7 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 7 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{inner l2, inner l3, inner l4}7
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4712
T Commandstrigger init lu-a2d 0 in-select 7 out-select 2
Page 4857
trigger init lu-a2d 0 in-select 8 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 8 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{outer l2, inner l2, ieth}8
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4713
T Commandstrigger init lu-a2d 0 in-select 8 out-select 0
Page 4858
trigger init lu-a2d 0 in-select 8 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 8 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{outer l2, inner l2, ieth}8
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4714
T Commandstrigger init lu-a2d 0 in-select 8 out-select 1
Page 4859
trigger init lu-a2d 0 in-select 8 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 8 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{outer l2, inner l2, ieth}8
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4715
T Commandstrigger init lu-a2d 0 in-select 8 out-select 2
Page 4860
trigger init lu-a2d 0 in-select 9 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 9 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{outer l3, inner l3}9
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4716
T Commandstrigger init lu-a2d 0 in-select 9 out-select 0
Page 4861
trigger init lu-a2d 0 in-select 9 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 9 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{outer l3, inner l3}9
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4717
T Commandstrigger init lu-a2d 0 in-select 9 out-select 1
Page 4862
trigger init lu-a2d 0 in-select 9 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 in-select 9 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
in-selectin-select
out-selectout-select
{outer l3, inner l3}9
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4718
T Commandstrigger init lu-a2d 0 in-select 9 out-select 2
Page 4863
trigger init lu-a2d 0 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
out-selectout-select
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4719
T Commandstrigger init lu-a2d 0 out-select 0
Page 4864
trigger init lu-a2d 0 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
out-selectout-select
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4720
T Commandstrigger init lu-a2d 0 out-select 1
Page 4865
trigger init lu-a2d 0 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 0 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUD0
out-selectout-select
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4721
T Commandstrigger init lu-a2d 0 out-select 2
Page 4866
trigger init lu-a2d 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4722
T Commandstrigger init lu-a2d 1
Page 4867
trigger init lu-a2d 1 in-select 10trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 10 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
{outer l4, inner l4, ieth}10
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4723
T Commandstrigger init lu-a2d 1 in-select 10
Page 4868
trigger init lu-a2d 1 in-select 10 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 10 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{outer l4, inner l4, ieth}10
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4724
T Commandstrigger init lu-a2d 1 in-select 10 out-select 0
Page 4869
trigger init lu-a2d 1 in-select 10 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 10 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{outer l4, inner l4, ieth}10
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4725
T Commandstrigger init lu-a2d 1 in-select 10 out-select 1
Page 4870
trigger init lu-a2d 1 in-select 10 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 10 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{outer l4, inner l4, ieth}10
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4726
T Commandstrigger init lu-a2d 1 in-select 10 out-select 2
Page 4871
trigger init lu-a2d 1 in-select 19trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 19 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
{udf_vec}19
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4727
T Commandstrigger init lu-a2d 1 in-select 19
Page 4872
trigger init lu-a2d 1 in-select 19 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 19 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{udf_vec}19
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4728
T Commandstrigger init lu-a2d 1 in-select 19 out-select 0
Page 4873
trigger init lu-a2d 1 in-select 19 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 19 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{udf_vec}19
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4729
T Commandstrigger init lu-a2d 1 in-select 19 out-select 1
Page 4874
trigger init lu-a2d 1 in-select 19 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 19 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{udf_vec}19
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4730
T Commandstrigger init lu-a2d 1 in-select 19 out-select 2
Page 4875
trigger init lu-a2d 1 in-select 6trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 6 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
{outer l2, outer l3, outer l4}6
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4731
T Commandstrigger init lu-a2d 1 in-select 6
Page 4876
trigger init lu-a2d 1 in-select 6 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 6 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{outer l2, outer l3, outer l4}6
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4732
T Commandstrigger init lu-a2d 1 in-select 6 out-select 0
Page 4877
trigger init lu-a2d 1 in-select 6 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 6 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{outer l2, outer l3, outer l4}6
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4733
T Commandstrigger init lu-a2d 1 in-select 6 out-select 1
Page 4878
trigger init lu-a2d 1 in-select 6 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 6 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{outer l2, outer l3, outer l4}6
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4734
T Commandstrigger init lu-a2d 1 in-select 6 out-select 2
Page 4879
trigger init lu-a2d 1 in-select 7trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 7 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
{inner l2, inner l3, inner l4}7
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4735
T Commandstrigger init lu-a2d 1 in-select 7
Page 4880
trigger init lu-a2d 1 in-select 7 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 7 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{inner l2, inner l3, inner l4}7
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4736
T Commandstrigger init lu-a2d 1 in-select 7 out-select 0
Page 4881
trigger init lu-a2d 1 in-select 7 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 7 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{inner l2, inner l3, inner l4}7
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4737
T Commandstrigger init lu-a2d 1 in-select 7 out-select 1
Page 4882
trigger init lu-a2d 1 in-select 7 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 7 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{inner l2, inner l3, inner l4}7
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4738
T Commandstrigger init lu-a2d 1 in-select 7 out-select 2
Page 4883
trigger init lu-a2d 1 in-select 8trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 8 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
{outer l2, inner l2, ieth}8
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4739
T Commandstrigger init lu-a2d 1 in-select 8
Page 4884
trigger init lu-a2d 1 in-select 8 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 8 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{outer l2, inner l2, ieth}8
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4740
T Commandstrigger init lu-a2d 1 in-select 8 out-select 0
Page 4885
trigger init lu-a2d 1 in-select 8 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 8 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{outer l2, inner l2, ieth}8
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4741
T Commandstrigger init lu-a2d 1 in-select 8 out-select 1
Page 4886
trigger init lu-a2d 1 in-select 8 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 8 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{outer l2, inner l2, ieth}8
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4742
T Commandstrigger init lu-a2d 1 in-select 8 out-select 2
Page 4887
trigger init lu-a2d 1 in-select 9trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 9 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
{outer l3, inner l3}9
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4743
T Commandstrigger init lu-a2d 1 in-select 9
Page 4888
trigger init lu-a2d 1 in-select 9 out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 9 out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{outer l3, inner l3}9
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4744
T Commandstrigger init lu-a2d 1 in-select 9 out-select 0
Page 4889
trigger init lu-a2d 1 in-select 9 out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 9 out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{outer l3, inner l3}9
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4745
T Commandstrigger init lu-a2d 1 in-select 9 out-select 1
Page 4890
trigger init lu-a2d 1 in-select 9 out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] lu-a2d 1 in-select 9 out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
Trigger at LUA/LUDlu-a2d
Trigger at LUA1
in-selectin-select
out-selectout-select
{outer l3, inner l3}9
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4746
T Commandstrigger init lu-a2d 1 in-select 9 out-select 2
Page 4891
trigger init out-select 0trigger init [ asic <asic-no> ] [ slice <slice-no> ] out-select 0 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
out-selectout-select
{header_vec, sideband, sb_info}0
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4747
T Commandstrigger init out-select 0
Page 4892
trigger init out-select 1trigger init [ asic <asic-no> ] [ slice <slice-no> ] out-select 1 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
out-selectout-select
{header_vec, sideband, lux_drop_vec}1
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4748
T Commandstrigger init out-select 1
Page 4893
trigger init out-select 2trigger init [ asic <asic-no> ] [ slice <slice-no> ] out-select 2 [ use-src-id <src-id> ]
Syntax Description
Define A Triggertrigger
Initialize Triggerinit
(Optional) ASIC instanceasic
(Optional) ASIC instance numberasic-no
(Optional) ASIC sliceslice
(Optional) ASIC slice numberslice-no
out-selectout-select
{sideband, sb_info, stats, lux_drop_vec}2
(Optional) Capture on ethernet interfaceuse-src-id
(Optional) interface indexsrc-id
Command Mode
• /exec/elamtah
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4749
T Commandstrigger init out-select 2
Page 4894
trigger resettrigger reset
Syntax Description
Define A Triggertrigger
Reset triggersreset
Command Mode
• /exec/elamns
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4750
T Commandstrigger reset
Page 4895
trigger route download vrf ipv4trigger route download vrf <vrf-name> { ipv4 <route4> | ipv6 <route6> } [ module <slot-num> ]
Syntax Description
Triggertrigger
IP route relatedroute
Downloaddownload
vrfvrf
vrf namevrf-name
ipv4ipv4
ipv4 prefixroute4
ipv6ipv6
(Optional) Modulemodule
(Optional) Slot number of the moduleslot-num
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4751
T Commandstrigger route download vrf ipv4
Page 4896
trunk protocol[no] trunk protocol [ enable ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Switch wide trunk protocoltrunk
enable trunk protocolprotocol
(Optional) enable trunk protocolenable
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4752
T Commandstrunk protocol
Page 4897
trusted-port[no] trusted-port
Syntax Description
(Optional) Negate a command or set its defaultsno
Command Mode
• /exec/configure/config-ra-guard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4753
T Commandstrusted-port
Page 4898
trusted-port[no] trusted-port
Syntax Description
(Optional) Negate a command or set its defaultsno
Command Mode
• /exec/configure/config-snoop-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4754
T Commandstrusted-port
Page 4899
trusted-port[no] trusted-port
Syntax Description
(Optional) Negate a command or set its defaultsno
Command Mode
• /exec/configure/config-dhcp-guard
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4755
T Commandstrusted-port
Page 4900
ttag-marker-interval[no] ttag-marker-interval <seconds>
Syntax Description
(Optional) Negate a command or set its defaultsno
Marker packet intervalttag-marker-interval
Interval in secondsseconds
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4756
T Commandsttag-marker-interval
Page 4901
ttag-marker-interval[no] ttag-marker-interval <seconds>
Syntax Description
(Optional) Negate a command or set its defaultsno
Marker packet intervalttag-marker-interval
Interval in secondsseconds
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4757
T Commandsttag-marker-interval
Page 4902
ttag-marker enable[no] ttag-marker enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/Disable marker packet on interfacettag-marker
Enable/Disable marker packet on interfaceenable
Command Mode
• /exec/configure/if-ethernet-switch /exec/configure/if-eth-l2-non-member/exec/configure/if-eth-port-channel /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4758
T Commandsttag-marker enable
Page 4903
ttag-marker enable[no] ttag-marker enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable/Disable marker packet on interfacettag-marker
Enable/Disable marker packet on interfaceenable
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4759
T Commandsttag-marker enable
Page 4904
ttag-strip[no] ttag-strip
Syntax Description
(Optional) Negate a command or set its defaultsno
strip ttag from egress packet on this interfacettag-strip
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4760
T Commandsttag-strip
Page 4905
ttag[no] ttag
Syntax Description
(Optional) Negate a command or set its defaultsno
enable ingress packet with ttag on this interfacettag
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4761
T Commandsttag
Page 4906
ttag[no] ttag
Syntax Description
(Optional) Negate a command or set its defaultsno
hardware ttag timestampttag
Command Mode
• /exec/configure/if-eth-base /exec/configure/if-ethernet-all
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4762
T Commandsttag
Page 4907
ttl-security hopsttl-security hops <ebgp-ttl> | { no | default } ttl-security hops [ <ebgp-ttl> ]
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Enable TTL Security Mechanismttl-security
Specify hop count for remote peerhops
EBGP hop count valueebgp-ttl
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4763
T Commandsttl-security hops
Page 4908
tunnel destinationtunnel destination { { <ip-addr> | <ip-prefix> | { <ip-addr> <ip-mask> } } | <ipv6-addr> } | no tunnel destination[ <ip-addr> | <ip-prefix> | { <ip-addr> <ip-mask> } | <ipv6-addr> ]
Syntax Description
Negate a command or set its defaultsno
protocol-over-protocol tunnelingtunnel
destination of tunnel packetsdestination
IPv4 address (A.B.C.D)ip-addr
IPv4 mask (A.B.C.D/LEN)ip-prefix
IPv4 mask A.B.C.Dip-mask
Command Mode
• /exec/configure/if-gre-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4764
T Commandstunnel destination
Page 4909
tunnel modetunnel mode { { gre [ ip | ipv6 ] } | { ipip [ ip | ipv6 ] } | { ipip decapsulate-any [ ip | ipv6 ] } | { ipv6ip [decapsulate-any ] } | { ipv6ipv6 [ decapsulate-any ] } } | no tunnel mode
Syntax Description
Negate a command or set its defaultsno
protocol-over-protocol tunnelingtunnel
tunnel encapsulation methodmode
generic route encapsulation protocolgre
IP in IP protocolipip
decapsulate anydecapsulate-any
(Optional) over IPip
(Optional) over IPv6ipv6
IPv6 in IPv4 protocolipv6ip
IPv6 in IPv6 protocolipv6ipv6
Command Mode
• /exec/configure/if-any-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4765
T Commandstunnel mode
Page 4910
tunnel path-mtu-discovery[no] tunnel path-mtu-discovery
Syntax Description
(Optional) Negate a command or set its defaultsno
protocol-over-protocol tunnelingtunnel
Enable Path MTU Discovery on tunnelpath-mtu-discovery
Command Mode
• /exec/configure/if-any-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4766
T Commandstunnel path-mtu-discovery
Page 4911
tunnel path-mtu-discovery age-timertunnel path-mtu-discovery age-timer { <age-time> | infinite } | no tunnel path-mtu-discovery age-timer [ {<age-time> | infinite } ]
Syntax Description
Negate a command or set its defaultsno
protocol-over-protocol tunnelingtunnel
Enable Path MTU Discovery on tunnelpath-mtu-discovery
Set PMTUD aging timerage-timer
Aging timeage-time
Disable pathmtu aging timerinfinite
Command Mode
• /exec/configure/if-any-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4767
T Commandstunnel path-mtu-discovery age-timer
Page 4912
tunnel path-mtu-discovery min-mtutunnel path-mtu-discovery min-mtu <mtu> | no tunnel path-mtu-discovery min-mtu [ <mtu> ]
Syntax Description
Negate a command or set its defaultsno
protocol-over-protocol tunnelingtunnel
Enable Path MTU Discovery on tunnelpath-mtu-discovery
Min pmtud mtu allowedmin-mtu
Bytesmtu
Command Mode
• /exec/configure/if-any-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4768
T Commandstunnel path-mtu-discovery min-mtu
Page 4913
tunnel sourcetunnel source { <intf> | <ip-prefix> | { <ip-addr> [ <ip-mask> ] } | <ipv6-addr> | direct } | no tunnel source[ <intf> | <ip-prefix> | { <ip-addr> [ <ip-mask> ] } | <ipv6-addr> | direct ]
Syntax Description
Negate a command or set its defaultsno
protocol-over-protocol tunnelingtunnel
source of tunnel packetssource
interfaceintf
IPv4 address (A.B.C.D)ip-addr
IPv4 address (A.B.C.D/LEN)ip-prefix
(Optional) IPv4 mask A.B.C.Dip-mask
all directly connected IPdirect
Command Mode
• /exec/configure/if-gre-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4769
T Commandstunnel source
Page 4914
tunnel ttltunnel ttl <ttl_val> | no tunnel ttl [ <ttl_val> ]
Syntax Description
Negate a command or set its defaultsno
protocol-over-protocol tunnelingtunnel
set time to livettl
time to live valuettl_val
Command Mode
• /exec/configure/if-any-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4770
T Commandstunnel ttl
Page 4915
tunnel use-vrftunnel use-vrf { <vrf-name> | <vrf-known-name> } | no tunnel use-vrf [ { <vrf-name> | <vrf-known-name>} ]
Syntax Description
Negate a command or set its defaultsno
protocol-over-protocol tunnelingtunnel
set tunnel vrf membershipuse-vrf
VRF namevrf-name
Known VRF namevrf-known-name
Command Mode
• /exec/configure/if-any-tunnel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4771
T Commandstunnel use-vrf
Page 4916
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4772
T Commandstunnel use-vrf
Page 4917
U Commands
• udf, on page 4775• udld aggressive, on page 4776• udld aggressive, on page 4777• udld aggressive, on page 4778• udld aggressive, on page 4779• udld continue-on-err, on page 4780• udld disable, on page 4781• udld disable, on page 4782• udld enable, on page 4783• udld enable, on page 4784• udld message-time, on page 4785• udld reset, on page 4786• udp-echo, on page 4787• udp-jitter, on page 4788• undebug all, on page 4790• undebug l2rib, on page 4791• uniq, on page 4792• unmount, on page 4793• unmount slot0, on page 4794• unsuppress-map, on page 4795• untagged cos, on page 4796• update-source, on page 4797• update-source, on page 4798• update license, on page 4799• update license, on page 4800• urib debugs-dump-to-file, on page 4801• use-chunking size, on page 4802• use-compression gzip, on page 4803• use-retry size, on page 4804• use-vrf, on page 4805• use-vrf, on page 4806• use-vrf, on page 4807• use-vrf, on page 4808
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4773
Page 4918
• user-jid password, on page 4809• user max-logins, on page 4810• user max-logins, on page 4811• username, on page 4812• username, on page 4813• username, on page 4814• username, on page 4815• username, on page 4816• username keypair export, on page 4817• username keypair generate, on page 4818• username keypair import, on page 4819• username password, on page 4820• username ssh-cert-dn dsa, on page 4821• username sshkey, on page 4822• userpassphrase, on page 4823• userpassphrase min, on page 4824• userpassphrase min, on page 4825• userprofile trustedCert CRLLookup user-switch-bind user-certdn-match user-pubkey-match attribute-namesearch-filter base-DN, on page 4826
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4774
U Commands
Page 4919
udfudf <udf_name> { packet-start | { header { outer | inner } { l3 | l4 } } } <offset> <length> | no udf <udf_name>[ { packet-start | { header { outer | inner } { l3 | l4 } } } <offset> <length> ]
Syntax Description
Negate the commandno
Define the User Defined Field (UDF)udf
Name of the UDF to configureudf_name
Offset base from packet-startpacket-start
Offset base configurationheader
Offset base: from outer headerouter
Offset base: from inner headerinner
Offset base: from l3 headerl3
Offset base: from l4 headerl4
Enter Offset in bytes for UDF (from offset base)offset
Enter Length in bytes for UDF (from offset)length
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4775
U Commandsudf
Page 4920
udld aggressive[no] udld aggressive
Syntax Description
Negate a command or set its defaultsno
UDLD protocoludld
Enable UDLD aggressive mode on all fiber optic portsaggressive
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4776
U Commandsudld aggressive
Page 4921
udld aggressiveudld aggressive
Syntax Description
UDLD protocoludld
Enable UDLD aggressive mode on all fiber optic portsaggressive
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4777
U Commandsudld aggressive
Page 4922
udld aggressiveudld aggressive
Syntax Description
UDLD protocoludld
Enable UDLD aggressive mode for interface(s)aggressive
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4778
U Commandsudld aggressive
Page 4923
udld aggressive[no] udld aggressive
Syntax Description
Negate a command or set its defaultsno
UDLD protocoludld
Enable UDLD aggressive mode for interface(s)aggressive
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4779
U Commandsudld aggressive
Page 4924
udld continue-on-err[no] udld continue-on-err
Syntax Description
(Optional) Negate a command or set its defaultsno
UDLD protocoludld
Force UDLD continue without disabling the portcontinue-on-err
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4780
U Commandsudld continue-on-err
Page 4925
udld disableudld disable
Syntax Description
UDLD protocoludld
Disable UDLD for fiber interface(s)disable
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4781
U Commandsudld disable
Page 4926
udld disable[no] udld disable
Syntax Description
Negate a command or set its defaultsno
UDLD protocoludld
Disable UDLD for fiber interface(s)disable
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4782
U Commandsudld disable
Page 4927
udld enableudld enable
Syntax Description
UDLD protocoludld
Enable UDLD for non-fiber interface(s)enable
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4783
U Commandsudld enable
Page 4928
udld enable[no] udld enable
Syntax Description
Negate a command or set its defaultsno
UDLD protocoludld
Enable UDLD for non-fiber interface(s)enable
Command Mode
• /exec/configure/if-ethernet-all /exec/configure/if-eth-base
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4784
U Commandsudld enable
Page 4929
udld message-timeudld message-time <i0> | no udld message-time
Syntax Description
Negate a command or set its defaultsno
UDLD protocoludld
Setting the time in seconds between UDLD probe messagesmessage-time
Enter the message timer value [default = 15]i0
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4785
U Commandsudld message-time
Page 4930
udld resetudld reset
Syntax Description
UDLD protocoludld
Reset all ports shut down by UDLDreset
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4786
U Commandsudld reset
Page 4931
udp-echo[no] udp-echo { <hostname> | <ip-address> } <port> { [ control { disable | enable } ] [ source-ip {<source-ip-hostname> | <source-ip-address> } ] [ source-port <source-port-number> ] } +
Syntax Description
(Optional)no
(Optional) enablecontrol
(Optional) <source-port-number>source-ip-address
UDP Echo Operationudp-echo
Destination hostname, broadcast disallowedhostname
Destination IP address, broadcast disallowedip-address
Port Number (Recommended port range between 1025-65534)port
(Optional) Enable control packets exchange (default)enable
(Optional) Disable control packets exchangedisable
(Optional) Source addresssource-ip
(Optional) source IP hostname, broadcast disallowedsource-ip-hostname
(Optional) Source Portsource-port
(Optional) Port Number (Recommended port range between 1025-65534)source-port-number
Command Mode
• /exec/configure/ip-sla
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4787
U Commandsudp-echo
Page 4932
udp-jitter[no] udp-jitter { <hostname> | <ip-address> } <dest-port> { { [ codec { g711alaw | g711ulaw | g729a } { [advantage-factor <advantage-num> ] [ codec-interval <codec-int> ] [ codec-numpackets <codec-numpack>] [ codec-size <codec-bytes> ] } + ] [ control { disable | enable } ] [ source-ip { <source-ip-hostname> |<source-ip-address> } ] [ source-port <src-port> ] } + | { [ interval <packet-interval> ] [ num-packets<num-packets> ] [ control { disable | enable } ] [ source-ip { <source-ip-hostname> | <source-ip-address> }] [ source-port <src-port> ] } + }
Syntax Description
(Optional)no
(Optional) g711alawcodec
(Optional) codec-sizecodec-numpackets
(Optional) intervalsource-port
(Optional) <codec-bytes>codec-numpack
(Optional) <source-ip-address>source-ip-hostname
UDP Jitter Operationudp-jitter
Destination hostname, broadcast disallowedhostname
Destination IP address, broadcast disallowedip-address
Port Number (Recommended port range between 1025-65534)dest-port
(Optional) G.711 A Law 64000 bpsg711alaw
(Optional) G.711 U Law 64000 bpsg711ulaw
(Optional) G.729 8000 bpsg729a
(Optional) Advantage Factoradvantage-factor
(Optional) Inter Packet Intervalcodec-interval
(Optional) Number of bytes in payloadcodec-size
(Optional) Advantage Factoradvantage-num
(Optional) Delaycodec-int
(Optional) Number of bytes in payloadcodec-bytes
(Optional) Delay (default 20)packet-interval
(Optional) Number of Packets (default 10)num-packets
(Optional) Inter Packet Intervalinterval
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4788
U Commandsudp-jitter
Page 4933
(Optional) Number of Packets to be transmittednum-packets
(Optional) Enable or disable control packetscontrol
(Optional) Enable control packets exchange (default)enable
(Optional) Disable control packets exchangedisable
(Optional) Source addresssource-ip
(Optional) source IP hostname, broadcast disallowedsource-ip-hostname
(Optional) source IP address, broadcast disallowedsource-ip-address
(Optional) Source Portsource-port
(Optional) Port Number (Recommended port range between 1025-65534)src-port
Command Mode
• /exec/configure/ip-sla
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4789
U Commandsudp-jitter
Page 4934
undebug allundebug all
Syntax Description
Disable Debugging functions (See also debug)undebug
Disable all debuggingall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4790
U Commandsundebug all
Page 4935
undebug l2ribundebug l2rib
Syntax Description
Disable Debugging functions (See also debug)undebug
L2RIB debug commandsl2rib
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4791
U Commandsundebug l2rib
Page 4936
uniq| uniq [ -c | -d | -f <nb-of-fields> | -s <nb-of-chars> | -u | -w <nb-chars-to-compare> | -i ] +
Syntax Description
Pipe command output to filter|
Discard all but one of successive identical linesuniq
(Optional) prefix lines by the number of occurrences-c
(Optional) only print duplicate lines-d
(Optional) avoid comparing the first N fields-f
(Optional) avoid comparing the first N characters-s
(Optional) only print unique lines-u
(Optional) compare no more than N characters in lines-w
(Optional) ignore differences in case when comparing-i
(Optional) number of initial fields to ignorenb-of-fields
(Optional) number of initial chars to ignorenb-of-chars
(Optional) max number of chars to comparenb-chars-to-compare
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4792
U Commandsuniq
Page 4937
unmountunmount { usb1: | usb2: }
Syntax Description
unmount expansion flash or USB storageunmount
Unmount USB drive in port 1usb1:
Unmount USB drive in port 2usb2:
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4793
U Commandsunmount
Page 4938
unmount slot0unmount slot0:
Syntax Description
unmount expansion flash or USB storageunmount
Unmount expansion flashslot0:
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4794
U Commandsunmount slot0
Page 4939
unsuppress-mapunsuppress-map <unsupp-rmap-name> | { no | default } unsuppress-map [ <unsupp-rmap-name> ]
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Route-map to selectively unsuppress suppressed routesunsuppress-map
Route-map nameunsupp-rmap-name
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4795
U Commandsunsuppress-map
Page 4940
untagged cosuntagged cos <ucos-value> | no untagged cos
Syntax Description
Negate a command or set its defaultsno
default to use for untagged packets on interfaceuntagged
IEEE 802.1Q class of service for QoS classificationcos
COS valueucos-value
Command Mode
• /exec/configure/if-set-qos
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4796
U Commandsuntagged cos
Page 4941
update-sourceupdate-source <interface> | { no | default } update-source [ <interface> ]
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Specify source of BGP session and updatesupdate-source
Interface nameinterface
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor-sess
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4797
U Commandsupdate-source
Page 4942
update-sourceupdate-source <interface> | no update-source
Syntax Description
Negate a command or set its defaultsno
Specify source of BMP session and messagesupdate-source
Interface nameinterface
Command Mode
• /exec/configure/router-bgp/router-bgp-bmp-server
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4798
U Commandsupdate-source
Page 4943
update licenseupdate license <uri0> { <license-file> [ force ] | <s0> }
Syntax Description
Update licenseupdate
Update a license filelicense
Specify URL for the new license fileuri0
License file to be updatedlicense-file
(Optional) Force update license (don't prompt)force
License file to be updateds0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4799
U Commandsupdate license
Page 4944
update licenseupdate license <uri0> { <license-file> [ force ] | <s0> }
Syntax Description
Update licenseupdate
Update a license filelicense
Specify URL for the new license fileuri0
License file to be updatedlicense-file
(Optional) Force update license (don't prompt)force
License file to be updateds0
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4800
U Commandsupdate license
Page 4945
urib debugs-dump-to-fileurib debugs-dump-to-file
Syntax Description
Unicast Routing Information Baseurib
Dump all urib debugs to a filedebugs-dump-to-file
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4801
U Commandsurib debugs-dump-to-file
Page 4946
use-chunking sizeuse-chunking size <kbytes> | no use-chunking
Syntax Description
Negate a command or set its defaultsno
Enable chunkinguse-chunking
Chunk sizesize
Specify chunking size in kilobyteskbytes
Command Mode
• /exec/configure/telemetry/destination-group
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4802
U Commandsuse-chunking size
Page 4947
use-compression gzipuse-compression { gzip } | no use-compression
Syntax Description
Negate a command or set its defaultsno
Specify the destination compression methoduse-compression
GZIP compression algorithmgzip
Command Mode
• /exec/configure/telemetry/destination-profile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4803
U Commandsuse-compression gzip
Page 4948
use-retry sizeuse-retry size <mbytes> | no use-retry
Syntax Description
Negate a command or set its defaultsno
Specify send retry detailsuse-retry
Retry buffer sizesize
Buffer size in Mega bytesmbytes
Command Mode
• /exec/configure/telemetry/destination-profile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4804
U Commandsuse-retry size
Page 4949
use-vrfuse-vrf { default | <vrf-cfg-name> } | no use-vrf
Syntax Description
Negate a command or set its defaultsno
Specify the destination vrfuse-vrf
Known VRF namedefault
Configurable VRF namevrf-cfg-name
Command Mode
• /exec/configure/telemetry/destination-profile
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4805
U Commandsuse-vrf
Page 4950
use-vrf[no] use-vrf { <vrf-name> | <vrf-known-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Display per-VRF informationuse-vrf
VRF namevrf-name
Known VRF namevrf-known-name
Command Mode
• /exec/configure/ldap
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4806
U Commandsuse-vrf
Page 4951
use-vrf[no] use-vrf { management | default | <vrf_name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
vrf to be used to contact servers in this groupuse-vrf
management vrfmanagement
default vrfdefault
name of the vrfvrf_name
Command Mode
• /exec/configure/radius
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4807
U Commandsuse-vrf
Page 4952
use-vrf[no] use-vrf { management | default | <vrf_name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
vrf to be used to contact servers in this groupuse-vrf
management vrfmanagement
default vrfdefault
name of the vrfvrf_name
Command Mode
• /exec/configure/tacacs+
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4808
U Commandsuse-vrf
Page 4953
user-jid password[no] user-jid <jid> password [ 0 <clear> | 7 <encrypted> | <password> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
User Jabber IDuser-jid
Enter user Jabber IDjid
Passwordpassword
(Optional) Password that follows should be in clear text0
(Optional) Password in clear textclear
(Optional) Password that follows should be in encrypted text7
(Optional) Encrypted passwordencrypted
(Optional) Enter password in clear textpassword
Command Mode
• /exec/configure/fabric-db/server-xmpp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4809
U Commandsuser-jid password
Page 4954
user max-loginsuser max-logins <limit>
Syntax Description
Configure system-wide user settingsuser
maximum simultaneous loginsmax-logins
login session maximumlimit
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4810
U Commandsuser max-logins
Page 4955
user max-logins[no] user max-logins [ <limit> ]
Syntax Description
Negate a command or set its defaultsno
Configure system-wide user settingsuser
maximum simultaneous loginsmax-logins
(Optional) login session maximumlimit
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4811
U Commandsuser max-logins
Page 4956
username[no] username <s0> { sshkey2 { file <uri0> | <line> } }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure user information.username
user names0
Update ssh key for the user for ssh authenticationsshkey2
ssh key filefile
file containing host public key for the useruri0
ssh key for the userline
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4812
U Commandsusername
Page 4957
username{ username <s0> [ password { 0 <s2> | 5 <s3> | <s4> } ] [ expire <s5> [ past ] ] [ priv-lvl <p> ] } | { username<s0> [ password { 0 <s2> | 5 <s3> | <s4> } ] [ priv-lvl <p> ] [ expire <s5> [ past ] ] } | { username <s0> [expire <s5> [ past ] ] [ password { 0 <s2> | 5 <s3> | <s4> } ] [ priv-lvl <p> ] } | { username <s0> [ expire<s5> [ past ] ] [ priv-lvl <p> ] [ password { 0 <s2> | 5 <s3> | <s4> } ] } | { username <s0> [ priv-lvl <p> ] [password { 0 <s2> | 5 <s3> | <s4> } ] [ expire <s5> [ past ] ] } | { username <s0> [ priv-lvl <p> ] [ expire<s5> [ past ] ] [ password { 0 <s2> | 5 <s3> | <s4> } ] } | { no username <s7> [ priv-lvl <p> ] }
Syntax Description
Negate a command or set its defaultsno
Configure user information.username
user names0
(Optional) Password for the userpassword
(Optional) Indicates that the password that follows should be in cleartext
0
(Optional) Password for the user (clear text)s2
(Optional) Indicates that the password that follows should be encrypted5
(Optional) strongly encrypted passwords3
(Optional) Password for the user (clear text)s4
(Optional) Expiry date for this user account(in YYYY-MM-DD format)expire
(Optional) Expiry in YYYY-MM-DD formats5
(Optional) Expiry date is in pastpast
user names7
(Optional) privilege level which the user is to be assigned topriv-lvl
(Optional) privilege levelp
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4813
U Commandsusername
Page 4958
username{ username <s0> [ password { 0 <s2> | 5 <s3> | <s4> } ] [ expire <s5> [ past ] ] [ role <s6> ] } | { username<s0> [ password { 0 <s2> | 5 <s3> | <s4> } ] [ role <s6> ] [ expire <s5> [ past ] ] } | { username <s0> [ expire<s5> [ past ] ] [ password { 0 <s2> | 5 <s3> | <s4> } ] [ role <s6> ] } | { username <s0> [ expire <s5> [ past] ] [ role <s6> ] [ password { 0 <s2> | 5 <s3> | <s4> } ] } | { username <s0> [ role <s6> ] [ password { 0 <s2>| 5 <s3> | <s4> } ] [ expire <s5> [ past ] ] } | { username <s0> [ role <s6> ] [ expire <s5> [ past ] ] [ password{ 0 <s2> | 5 <s3> | <s4> } ] } | { no username <s7> [ role <s8> ] }
Syntax Description
Negate a command or set its defaultsno
Configure user information.username
user names0
(Optional) Password for the userpassword
(Optional) Indicates that the password that follows should be in cleartext
0
(Optional) Password for the user (clear text)s2
(Optional) Indicates that the password that follows should be encrypted5
(Optional) strongly encrypted passwords3
(Optional) Password for the user (clear text)s4
(Optional) Expiry date for this user account(in YYYY-MM-DD format)expire
(Optional) Expiry in YYYY-MM-DD formats5
(Optional) Expiry date is in pastpast
(Optional) role which the user is to be assigned torole
(Optional) role names6
user names7
(Optional) role names8
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4814
U Commandsusername
Page 4959
username{ username <s0> { shelltype { vsh | bash } } }
Syntax Description
Configure user information.username
user names0
Choose shell type for loginshelltype
use vsh shellvsh
use bash shellbash
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4815
U Commandsusername
Page 4960
username{ [ no ] username <name> }
Syntax Description
user nameusername
user namename
Command Mode
• /exec/configure/dot1x-cred
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4816
U Commandsusername
Page 4961
username keypair export{ username <s0> keypair export <s1> { dsa | rsa | ecdsa } [ force ] }
Syntax Description
Configure user information.username
Use existing ssh keypairkeypair
Export keypair to Bootflash/Remote directoryexport
(Optional) Force the export of keys even if the destination files arepresent
force
Use DSA Keysdsa
Use RSA Keysrsa
Use ECDSA Keysecdsa
user names0
Enter filename to export tos1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4817
U Commandsusername keypair export
Page 4962
username keypair generate{ username <s0> keypair generate { dsa [ force ] | rsa [ <i0> | <oldrange> ] [ force ] | ecdsa { <i0> } [ force] } | no username <s0> keypair generate [ { dsa [ force ] | rsa [ <i0> | <oldrange> ] [ force ] | ecdsa [ { <i0> }[ force ] ] } ] }
Syntax Description
Negate a command or set its defaultsno
Configure user information.username
user names0
Generate ssh key pairsgenerate
Generate SSH User Keyskeypair
Generate DSA keysdsa
(Optional) Force the generation of keys even if previous ones are presentforce
Generate RSA keysrsa
(Optional) Enter number of bits (in multiples of 8)i0
(Optional) Enter number of bitsoldrange
Generate ECDSA keysecdsa
Enter key size in bits (256, 384 or 521)i0
(Optional) Force the generation of keys even if previous ones are presentforce
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4818
U Commandsusername keypair generate
Page 4963
username keypair import{ username <s0> keypair import <s1> { dsa | rsa | ecdsa } [ force ] }
Syntax Description
Configure user information.username
Use existing ssh keypairkeypair
Import keypair from Bootflash/Remote directoryimport
(Optional) Force the generation of keys even if previous ones are presentforce
Use DSA Keysdsa
Use RSA Keysrsa
Use ECDSA Keysecdsa
user names0
Enter filename to imports1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4819
U Commandsusername keypair import
Page 4964
username password[no] username <user> password { 0 <pass1> | 5 <pass2> | <pass3> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure user nameusername
Usernameuser
Password for userpassword
Indicates that the password that follows should be in clear text0
Password for the user (clear text)pass1
Indicates that the password that follows should be encrypted5
strongly encrypted passwordpass2
Password for the user (clear text)pass3
Command Mode
• /exec/configure/vmt-conn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4820
U Commandsusername password
Page 4965
username ssh-cert-dn dsa[no] username <s1> ssh-cert-dn <s2> { dsa | rsa }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure user information.username
user names1
Update cert dnssh-cert-dn
distinguished name to be useds2
Use dsa algorithmdsa
Use rsa algorithmrsa
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4821
U Commandsusername ssh-cert-dn dsa
Page 4966
username sshkey{ username <s0> sshkey { file <uri0> | <line> } | no username <s0> sshkey }
Syntax Description
Configure user information.username
user names0
Update ssh key for the user for ssh authenticationsshkey
ssh key filefile
file containing host public key for the useruri0
ssh key for the userline
Negate a command or set its defaultsno
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4822
U Commandsusername sshkey
Page 4967
userpassphrase[no] userpassphrase { min-length | max-length | length }
Syntax Description
Negate a command or set its defaultsno
user passphraseuserpassphrase
passphrase minimum lengthmin-length
passphrase maximum lengthmax-length
passphrase min and max lengthlength
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4823
U Commandsuserpassphrase
Page 4968
userpassphrase min[no] userpassphrase { min-length <min-len> | max-length <max-len> } +
Syntax Description
Negate a command or set its defaultsno
user passphraseuserpassphrase
passphrase minimum lengthmin-length
passphrase maximum lengthmax-length
minimum length of passphrasemin-len
maximum length of passphrasemax-len
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4824
U Commandsuserpassphrase min
Page 4969
userpassphrase minuserpassphrase { min-length <min-len> | max-length <max-len> } +
Syntax Description
user passphraseuserpassphrase
passphrase minimum lengthmin-length
passphrase maximum lengthmax-length
minimum length of passphrasemin-len
maximum length of passphrasemax-len
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4825
U Commandsuserpassphrase min
Page 4970
userprofile trustedCert CRLLookup user-switch-binduser-certdn-match user-pubkey-match attribute-namesearch-filter base-DN
{ userprofile | trustedCert | CRLLookup | user-switch-bind | user-certdn-match | user-pubkey-match }attribute-name <s0> search-filter <s1> base-DN <s2>
Syntax Description
Set the userprofileuserprofile
Set the trustedCerttrustedCert
Set the CRLLookupCRLLookup
Set the user-switch-binduser-switch-bind
Set the certificate matchinguser-certdn-match
Set the pubkey matchinguser-pubkey-match
LDAP attribute-nameattribute-name
Search Map attribute-names0
LDAP search-filtersearch-filter
Search Map search-filters1
LDAP base-DNbase-DN
Search Map base-DN Names2
Command Mode
• /exec/configure/ldap/search
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4826
U Commandsuserprofile trustedCert CRLLookup user-switch-bind user-certdn-match user-pubkey-match attribute-name search-filter base-DN
Page 4971
V Commands
• validate-json, on page 4830• validate-xml, on page 4831• validate-xml, on page 4832• vdc, on page 4833• vdc, on page 4834• vdc combined-hostname, on page 4835• vdc_id, on page 4836• vdc resource template, on page 4837• vdc suspend, on page 4838• vdc suspend, on page 4839• vdp dot1q default static, on page 4840• vdp dot1q static, on page 4841• vdp vni default static, on page 4842• vdp vni static, on page 4843• verify-data, on page 4844• verify-host, on page 4845• verify, on page 4846• verify profile, on page 4847• verify verbose, on page 4848• version, on page 4849• version 9, on page 4850• virtual-service, on page 4851• virtual-service, on page 4852• virtual-service, on page 4853• virtual-service move name log to, on page 4854• virtual-service reset force, on page 4855• virtual IPv6, on page 4856• virtual IPv6, on page 4857• virtual ip, on page 4858• virtual ip, on page 4859• vlan-consistency-check, on page 4860• vlan-pruning enable, on page 4861• vlan, on page 4862
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4827
Page 4972
• vlan2, on page 4863• vlan, on page 4864• vlan, on page 4865• vlan access-map, on page 4866• vlan configuration, on page 4867• vlan designated priority, on page 4868• vlan filter vlan, on page 4869• vlan root priority, on page 4870• vmtracker connection, on page 4871• vmtracker connection refresh, on page 4872• vmtracker enable, on page 4873• vmtracker fabric auto-config, on page 4874• vn-segment, on page 4875• vni, on page 4876• vni, on page 4877• vni, on page 4878• vni default dynamic, on page 4879• vni l2, on page 4880• vpc, on page 4881• vpc domain, on page 4882• vpc orphan-port suspend, on page 4883• vpc peer-link, on page 4884• vpc role preempt, on page 4885• vpn, on page 4886• vpn id, on page 4887• vrf, on page 4888• vrf, on page 4889• vrf, on page 4890• vrf, on page 4891• vrf, on page 4892• vrf, on page 4893• vrf, on page 4894• vrf, on page 4895• vrf, on page 4896• vrf, on page 4897• vrf, on page 4898• vrf, on page 4899• vrf, on page 4900• vrf context, on page 4901• vrf default static, on page 4902• vrf member, on page 4903• vrf member, on page 4904• vrf static, on page 4905• vrrp, on page 4906• vrrp bfd, on page 4907• vrrpv2, on page 4908
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4828
V Commands
Page 4973
• vrrpv3, on page 4909• vrrpv3 address-family, on page 4910• vrrpv3 address-family, on page 4911• vrrs leader, on page 4912• vrrs pathway, on page 4913• vsh, on page 4914• vtp, on page 4915• vtp domain, on page 4916• vtp file, on page 4917• vtp mode, on page 4918• vtp password, on page 4919• vtp pruning, on page 4920• vtp version, on page 4921
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4829
V Commands
Page 4974
validate-json| validate-json
Syntax Description
Pipe command output to filter|
validate json output according to .xsd definitionsvalidate-json
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4830
V Commandsvalidate-json
Page 4975
validate-xml| validate-xml
Syntax Description
Pipe command output to filter|
validate an xml output according to .xsd definitionsvalidate-xml
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4831
V Commandsvalidate-xml
Page 4976
validate-xml| validate-xml
Syntax Description
Pipe command output to filter|
validate an xml output according to .xsd definitionsvalidate-xml
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4832
V Commandsvalidate-xml
Page 4977
vdc[no] vdc <e-vdc> [ force ]
Syntax Description
Negate a command or set its defaultsno
Manage Virtual Device Contextvdc
Enter Virtual Device Context <vdc-id>e-vdc
(Optional) Force ungraceful cleanupforce
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4833
V Commandsvdc
Page 4978
vdcvdc <e-vdc> [ id <new_id> ] [ type <vtype> ]
Syntax Description
Manage Virtual Device Contextvdc
Enter Virtual Device Context <vdc-id>e-vdc
(Optional) force this vdc into a specific idid
(Optional) force this vdc into a specific idnew_id
(Optional) Create vdc with a special set of servicestype
(Optional) type of vdcvtype
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4834
V Commandsvdc
Page 4979
vdc combined-hostname[no] vdc combined-hostname
Syntax Description
(Optional) Negate a command or set its defaultsno
Manage Virtual Device Contextvdc
The hostname of non-default vdcs will be <default vdcname>-<nondefault vdc name>
combined-hostname
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4835
V Commandsvdc combined-hostname
Page 4980
vdc_id[no] vdc_id <id>
Syntax Description
Negate a command or set its defaultsno
Manage Virtual Device Contextvdc_id
Enter Virtual Device Context <vdc-id>id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4836
V Commandsvdc_id
Page 4981
vdc resource template[no] vdc resource template { <name> | <res-mgr-template-known-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Manage Virtual Device Contextvdc
Configure resource templateresource
Configure resource templatetemplate
Resource template namename
Resource template nameres-mgr-template-known-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4837
V Commandsvdc resource template
Page 4982
vdc suspendvdc <en-vdc> suspend
Syntax Description
Manage Virtual Device Contextvdc
Enter Virtual Device Context <vdc-id>en-vdc
Put the vdc in a paused state. When resumed vdc will come up with itsstartup config
suspend
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4838
V Commandsvdc suspend
Page 4983
vdc suspend[no] vdc <en-vdc> suspend
Syntax Description
Manage Virtual Device Contextvdc
Enter Virtual Device Context <vdc-id>en-vdc
Put the vdc in a paused stated. When resumed vdc will use its startupconfig
suspend
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4839
V Commandsvdc suspend
Page 4984
vdp dot1q default static{ vdp dot1q default { static <profile-name> | dynamic } } | { no vdp dot1q default }
Syntax Description
Negate a command or set its defaultsno
VDP protocol triggersvdp
Static Profile Map: Configure profile name via CLIstatic
Static Profile Map: Configure profile name via CLIprofile-name
Dynamic Profile Map: Retrieve profile name from the external serverdynamic
Dot1Q Encapsulationdot1q
Default (wildcard). Match any dot1q when there is no specific dot1qmapping configured
default
Command Mode
• /exec/configure/profile-map /exec/configure/profile-map-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4840
V Commandsvdp dot1q default static
Page 4985
vdp dot1q static{ vdp dot1q <vlan-id> { static <profile-name> | dynamic } } | { no vdp dot1q <vlan-id> }
Syntax Description
Negate a command or set its defaultsno
VDP protocol triggersvdp
Static Profile Map: Configure profile name via CLIstatic
Static Profile Map: Configure profile name via CLIprofile-name
Dynamic Profile Map: Retrieve profile name from the external serverdynamic
Dot1Q Encapsulationdot1q
vlan-id
Command Mode
• /exec/configure/profile-map /exec/configure/profile-map-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4841
V Commandsvdp dot1q static
Page 4986
vdp vni default static{ vdp vni default { static <profile-name> | dynamic } } | { no vdp vni default }
Syntax Description
Negate a command or set its defaultsno
VDP protocol triggersvdp
Virtual Network Identifiervni
Static Profile Map: Configure profile name via CLIstatic
Dynamic Profile Map: Retrieve profile name from the external serverdynamic
Static Profile Map: Configure profile name via CLIprofile-name
Default (wildcard). Match any vni when there is no specific vni mappingconfigured
default
Command Mode
• /exec/configure/profile-map /exec/configure/profile-map-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4842
V Commandsvdp vni default static
Page 4987
vdp vni static{ vdp vni <vni-id> { static <profile-name> | dynamic } } | { no vdp vni <vni-id> }
Syntax Description
Negate a command or set its defaultsno
VDP protocol triggersvdp
Virtual Network Identifiervni
vni-id
Static Profile Map: Configure profile name via CLIstatic
Dynamic Profile Map: Retrieve profile name from the external serverdynamic
Static Profile Map: Configure profile name via CLIprofile-name
Command Mode
• /exec/configure/profile-map /exec/configure/profile-map-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4843
V Commandsvdp vni static
Page 4988
verify-data{ { no | default } verify-data | verify-data }
Syntax Description
no
Set a command to its defaultsdefault
Verify dataverify-data
Command Mode
• /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/icmpEcho
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4844
V Commandsverify-data
Page 4989
verify-host{ verify-host | no verify-host }
Syntax Description
Negate a command or set its defaultsno
Verify host reachability - payload info mandatoryverify-host
Command Mode
• /exec/configure/configngoamconnectcheck
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4845
V Commandsverify-host
Page 4990
verifyverify
Syntax Description
Verify the current configuration sessionverify
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4846
V Commandsverify
Page 4991
verify profileverify profile <all_conf_profile_name> [ __readonly__ TABLE_profile_name <missing_param> ]
Syntax Description
Verify the instance with a configuration profileverify
Name of the configuration profileprofile
Enter the name of configuration profileall_conf_profile_name
(Optional)__readonly__
(Optional)TABLE_profile_name
(Optional)missing_param
Command Mode
• /exec/configure/param-inst
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4847
V Commandsverify profile
Page 4992
verify verboseverify verbose
Syntax Description
Verify the current configuration sessionverify
Verify the current configuration session with more detailsverbose
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4848
V Commandsverify verbose
Page 4993
version[no] version <s0> [ <s1> ] [ <s2> ] [ <s3> ] [ <s4> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Version infoversion
Versions0
(Optional) Version1s1
(Optional) Version2s2
(Optional) Version3s3
(Optional) Version4s4
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4849
V Commandsversion
Page 4994
version 9version 9
Syntax Description
Specify the export versionversion
Version 9 Export9
Command Mode
• /exec/configure/nfm-exporter
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4850
V Commandsversion 9
Page 4995
virtual-service[no] virtual-service <virt_serv_name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a virtual servicevirtual-service
Virtual service namevirt_serv_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4851
V Commandsvirtual-service
Page 4996
virtual-service[no] virtual-service
Syntax Description
(Optional) Negate a command or set its defaultsno
Virtual service global settingsvirtual-service
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4852
V Commandsvirtual-service
Page 4997
virtual-servicevirtual-service { { install name <virt_serv_name> package <file_uri> [ media <target_media> ] } | { upgradename <virt_serv_name> package <file_uri> } | { uninstall name <virt_serv_name> } }
Syntax Description
Virtualization manager actionsvirtual-service
Add a virtual service to install databaseinstall
Upgrade a virtual service package to a different versionupgrade
Name of the virtual servicename
Virtual service namevirt_serv_name
Package locationpackage
File name (with .ova extension) for the virtual servicefile_uri
(Optional) Target media to use to explode the virtual service packagemedia
(Optional) Target mediatarget_media
Remove a virtual service from the install databaseuninstall
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4853
V Commandsvirtual-service
Page 4998
virtual-service move name log tovirtual-service move name <virt_serv_name> { log | core } to <dir_uri>
Syntax Description
Virtualization service actionsvirtual-service
Move a virtual service log or core filesmove
Name of the virtual servicename
Name of existing virtual servicevirt_serv_name
Move log fileslog
Move core filescore
Destination directory to move log or core files toto
Destination directory namedir_uri
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4854
V Commandsvirtual-service move name log to
Page 4999
virtual-service reset forcevirtual-service reset force
Syntax Description
Virtualization service actionsvirtual-service
Virtualization reset commandsreset
Force a non-recoverable reset of all virtualization filesforce
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4855
V Commandsvirtual-service reset force
Page 5000
virtual IPv6[no] virtual IPv6 { <ip-addr> { <prefix> | <netmask> } } [ ip | { { udp | tcp } { <port_num> | any } } ] [ {advertise } { enable | disable } [ active ] ] [ device-group <dgrp_name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD virtual ip configurationvirtual
ITD virtual IPv6IPv6
IPV6 prefix lengthprefix
(Optional) IP Protocolip
(Optional) UDP Protocoludp
(Optional) TCP Protocoltcp
(Optional) Port Numberport_num
(Optional) Any Port Numberany
(Optional) advertiseadvertise
(Optional) Enableenable
(Optional) Disabledisable
(Optional) Advertise route on at least one node activeactive
(Optional) device-groupdevice-group
(Optional) VIP device-group namedgrp_name
Command Mode
• /exec/configure/itd
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4856
V Commandsvirtual IPv6
Page 5001
virtual IPv6[no] virtual IPv6 { <ip-addr> { <prefix> | <netmask> } } [ ip | { { udp | tcp } { <port_num> | any } } ] [ { arp| advertise } { enable | disable } ] [ device-group <group-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Virtual IP of server nodes for redirectionvirtual
IPv6 addressIPv6
IPV6 prefix lengthprefix
(Optional) IP addressip
(Optional) UDP portudp
(Optional) TCP porttcp
(Optional) Port Numberport_num
(Optional) Any Port Numberany
(Optional) ARParp
(Optional) advertiseadvertise
(Optional) Enableenable
(Optional) Disabledisable
(Optional) Specify device group mapped to VIPdevice-group
(Optional) Device-group name mapped to VIPgroup-name
Command Mode
• /exec/configure/plb
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4857
V Commandsvirtual IPv6
Page 5002
virtual ip[no] virtual ip { <ip-addr> <ip-mask> } [ ip | { { udp | tcp } { <port_num> | any } } ] [ { advertise } { enable| disable } [ active ] ] [ device-group <dgrp_name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
ITD virtual ip configurationvirtual
ITD virtual ipip
IP address in format i.i.i.iip-addr
IP network mask in format m.m.m.mip-mask
(Optional) IP Protocolip
(Optional) UDP Protocoludp
(Optional) TCP Protocoltcp
(Optional) Port Numberport_num
(Optional) Any Port Numberany
(Optional) advertiseadvertise
(Optional) Enableenable
(Optional) Disabledisable
(Optional) Advertise route on at least one node activeactive
(Optional) device-groupdevice-group
(Optional) VIP device-group namedgrp_name
Command Mode
• /exec/configure/itd
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4858
V Commandsvirtual ip
Page 5003
virtual ip[no] virtual ip { <ip-addr> <ip-mask> } [ ip | { { udp | tcp } { <port_num> | any } } ] [ { arp | advertise } {enable | disable } ] [ device-group <group-name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Virtual IP of server nodes for redirectionvirtual
IPv4 addressip
IPv4 prefix in format i.i.i.iip-addr
IPv4 prefix mask in format m.m.m.mip-mask
(Optional) IPv4 addressip
(Optional) UDP portudp
(Optional) TCP porttcp
(Optional) Port Numberport_num
(Optional) Any Port Numberany
(Optional) ARParp
(Optional) advertiseadvertise
(Optional) Enableenable
(Optional) Disabledisable
(Optional) Specify device group mapped to VIPdevice-group
(Optional) Device-group name mapped to VIPgroup-name
Command Mode
• /exec/configure/plb
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4859
V Commandsvirtual ip
Page 5004
vlan-consistency-check[no] vlan-consistency-check
Syntax Description
(Optional) Negate a command or set its defaultsno
enable vlan consistency checkvlan-consistency-check
Command Mode
• /exec/configure/evpn-esi-mh
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4860
V Commandsvlan-consistency-check
Page 5005
vlan-pruning enablevlan-pruning enable | no vlan-pruning enable
Syntax Description
Negate a command or set its defaultsno
Configure Vlan-pruning featurevlan-pruning
Set the mode for vlan-pruningenable
Command Mode
• /exec/configure/l2mp-isis/l2mp-isis-vrf-common
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4861
V Commandsvlan-pruning enable
Page 5006
vlanvlan <vlans> | no vlan
Syntax Description
Negate a command or set its defaultsno
Set allowed fabricpath VLANs for a given anycast bundlevlan
VLAN IDs of the allowed fabricpath VLANs in the anycast bundlevlans
Command Mode
• /exec/configure/anycast
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4862
V Commandsvlan
Page 5007
vlan2[no] vlan2 <vlan-id-create-delete>
Syntax Description
(Optional) Negate a command or set its defaultsno
Vlan commandsvlan2
VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19vlan-id-create-delete
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4863
V Commandsvlan2
Page 5008
vlan[no] vlan <vlan-range>
Syntax Description
(Optional) Negate a command or set its defaultsno
add vlan to vlan groupvlan
range of vlansvlan-range
Command Mode
• /exec/configure/itd-vlan-grp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4864
V Commandsvlan
Page 5009
vlan[no] vlan <vlan-range>
Syntax Description
(Optional) Negate a command or set its defaultsno
vlanvlan
range of vlansvlan-range
Command Mode
• /exec/configure/smartc /exec/configure/smartc
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4865
V Commandsvlan
Page 5010
vlan access-map[no] vlan access-map <name> [ <seqno> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Vlan commandsvlan
List namename
Configure a VLAN access mapaccess-map
(Optional) Sequence numberseqno
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4866
V Commandsvlan access-map
Page 5011
vlan configuration[no] vlan configuration <vlan-id-create-delete>
Syntax Description
(Optional) Negate a command or set its defaultsno
Vlan commandsvlan
vlan feature configuration modeconfiguration
VLAN ID 1-4094 or range(s): 1-5, 10 or 2-5,7-19vlan-id-create-delete
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4867
V Commandsvlan configuration
Page 5012
vlan designated priority{ vlan <vlan-id> | bridge-domain <bd-id> } designated priority <prio> | no { vlan <vlan-id> | bridge-domain<bd-id> } designated priority [ <prio> ]
Syntax Description
Negate a command or set its defaultsno
VLAN Switch Spanning Treesvlan
Bridge-Domain Switch Spanning Treesbridge-domain
vlan range, Example: 1,3-5,7,9-11vlan-id
Bridge-Domain range, Example: 2,4-5,7,9-11bd-id
Set the designated bridge priority for the spanning treedesignated
Set the bridge priority for the spanning treepriority
bridge priority in increments of 4096prio
Command Mode
• /exec/configure/spanning-tree/pseudo
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4868
V Commandsvlan designated priority
Page 5013
vlan filter vlan[no] vlan filter <name> { vlan-list <vlans> | vlan-list-include-reserved <vlans-include-reserved> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Vlan commandsvlan
Specify access control for packetsfilter
List namename
Specify list of VLANs to apply access controlvlan-list
List of VLANsvlans
Specify list of VLANs to apply access controlvlan-list-include-reserved
List of VLANsvlans-include-reserved
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4869
V Commandsvlan filter vlan
Page 5014
vlan root priority{ vlan <vlan-id> | bridge-domain <bd-id> } root priority <prio> | no { vlan <vlan-id> | bridge-domain <bd-id>} root priority [ <prio> ]
Syntax Description
Negate a command or set its defaultsno
VLAN Switch Spanning Treesvlan
Bridge-Domain Switch Spanning Treesbridge-domain
vlan range, Example: 1,3-5,7,9-11vlan-id
Bridge-Domain range, Example: 2,4-5,7,9-11bd-id
Set the root bridge priority for the spanning treeroot
Set the bridge priority for the spanning treepriority
bridge priority in increments of 4096prio
Command Mode
• /exec/configure/spanning-tree/pseudo
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4870
V Commandsvlan root priority
Page 5015
vmtracker connection[no] vmtracker connection <connection-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure vmtracker parametersvmtracker
Specify a host to connectconnection
VM host nameconnection-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4871
V Commandsvmtracker connection
Page 5016
vmtracker connection refresh[no] vmtracker connection <connection-name> refresh
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure vmtracker parametersvmtracker
Specify a host to connectconnection
VM host nameconnection-name
Refresh all host related informationrefresh
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4872
V Commandsvmtracker connection refresh
Page 5017
vmtracker enable[no] vmtracker enable
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure vmtracker featurevmtracker
Enable vmtracker feature on interfaceenable
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4873
V Commandsvmtracker enable
Page 5018
vmtracker fabric auto-config[no] vmtracker fabric auto-config
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure vmtracker parametersvmtracker
Enable VM Tracker Fabric paramtersfabric
Enable VM Tracker Fabric AutoConfigurationauto-config
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4874
V Commandsvmtracker fabric auto-config
Page 5019
vn-segmentvn-segment { <segment-id> | <zero-segment-id> } | no vn-segment
Syntax Description
Negate a command or set its defaultsno
VN Segment id of the VLANvn-segment
segment-idsegment-id
segment-idzero-segment-id
Command Mode
• /exec/configure/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4875
V Commandsvn-segment
Page 5020
vni[no] vni <vni-id-sh>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure a vni-based static hostvni
vni-id-sh
Command Mode
• /exec/configure/static-host
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4876
V Commandsvni
Page 5021
vni{ vni <id> } | { no vni [ <id> ] }
Syntax Description
Negate a command or set its defaultsno
Virtual Network Identifiervni
vni, Example: 4096,6099id
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4877
V Commandsvni
Page 5022
vni{ vni <vni-id> | no vni }
Syntax Description
Negate a command or set its defaultsno
Vnivni
Configure vni idvni-id
Command Mode
• /exec/configure/configngoamconnectcheck
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4878
V Commandsvni
Page 5023
vni default dynamic{ vni default dynamic } | { no vni default }
Syntax Description
Negate a command or set its defaultsno
Dynamic Profile Map: Retrieve profile name from the external serverdynamic
Virtual Network Identifiervni
Default (wildcard). Match any vni when there is no specific vni mappingconfigured
default
Command Mode
• /exec/configure/profile-map /exec/configure/profile-map-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4879
V Commandsvni default dynamic
Page 5024
vni l2[no] vni <vni_id> l2
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure Ethernet VPN IDvni
Specify VNI IDvni_id
Layer-2 VNIl2
Command Mode
• /exec/configure/evpn
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4880
V Commandsvni l2
Page 5025
vpcvpc [ <vpc_num> ] | no vpc [ <vpc_num> ]
Syntax Description
Negate a command or set its defaultsno
Virtual Port Channel configurationvpc
(Optional) specify a Virtual Port Channel numbervpc_num
Command Mode
• /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4881
V Commandsvpc
Page 5026
vpc domainvpc domain <domain_id> | no vpc domain <domain_id>
Syntax Description
Negate a command or set its defaultsno
Virtual Port Channel configurationvpc
Specify domaindomain
domain iddomain_id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4882
V Commandsvpc domain
Page 5027
vpc orphan-port suspend[no] vpc orphan-port suspend
Syntax Description
(Optional) Negate a command or set its defaultsno
Virtual Port Channel configurationvpc
orphan-port (non-vpc port)orphan-port
suspend - when vPC secondary peerlink goes downsuspend
Command Mode
• /exec/configure/if-eth-phy /exec/configure/if-eth-port-channel-switch /exec/configure/if-eth-port-channel
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4883
V Commandsvpc orphan-port suspend
Page 5028
vpc peer-linkvpc peer-link | no vpc peer-link
Syntax Description
Negate a command or set its defaultsno
Virtual Port Channel configurationvpc
specify if this link is used for peer communicationpeer-link
Command Mode
• /exec/configure/if-eth-port-channel-switch
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4884
V Commandsvpc peer-link
Page 5029
vpc role preemptvpc role preempt
Syntax Description
Virtual Port Channel configurationvpc
vPC role related commandrole
Enable/Trigger preemption of lower priority masterpreempt
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4885
V Commandsvpc role preempt
Page 5030
vpn[no] vpn <otv-isis-vpn-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure IS-IS VPN name eg: Overlay<x>vpn
Overlay nameotv-isis-vpn-name
Command Mode
• /exec/configure/otv-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4886
V Commandsvpn
Page 5031
vpn idvpn id <vpn-id> | no vpn id [ <vpn-id> ]
Syntax Description
Negate a command or set its defaultsno
Configure VPN ID in rfc2685 formatvpn
Configure VPN ID in rfc2685 formatid
OUI:VPN-Index, format (hex) <3 bytes OUI:4 bytes VPN-Index>vpn-id
Command Mode
• /exec/configure/vrf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4887
V Commandsvpn id
Page 5032
vrf[no] vrf <vrf-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure RIP VRF informationvrf
VRF namevrf-name
Command Mode
• /exec/configure/router-rip
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4888
V Commandsvrf
Page 5033
vrf[no] vrf [ <name> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
Catena service vrfvrf
(Optional) Catena Service VRF namename
Command Mode
• /exec/configure/catena-device-grp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4889
V Commandsvrf
Page 5034
vrf[no] vrf { <vrf-name> | <vrf-known-name> }
Syntax Description
(Optional) Negate a command or set its defaultsno
set vrf membershipvrf
VRF namevrf-name
Known VRF namevrf-known-name
Command Mode
• /exec/configure/config-monitor-erspan-src
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4890
V Commandsvrf
Page 5035
vrf[no] vrf <vrf-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure ISIS VRF informationvrf
VRF namevrf-name
Command Mode
• /exec/configure/router-isis
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4891
V Commandsvrf
Page 5036
vrf[no] vrf <vrf-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Display per-VRF informationvrf
VRF namevrf-name
Command Mode
• /exec/configure/router-ospf3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4892
V Commandsvrf
Page 5037
vrf[no] vrf <vrf-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure VRF informationvrf
VRF namevrf-name
Command Mode
• /exec/configure/router-eigrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4893
V Commandsvrf
Page 5038
vrf[no] vrf <vrf-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Display per-VRF informationvrf
VRF namevrf-name
Command Mode
• /exec/configure/router-ospf
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4894
V Commandsvrf
Page 5039
vrf{ vrf <name> } | { no vrf <name> }
Syntax Description
Negate a command or set its defaultsno
ITD service vrfvrf
ITD Service VRF namename
Command Mode
• /exec/configure/itd
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4895
V Commandsvrf
Page 5040
vrf[no] vrf <vrf-cfg-name>
Syntax Description
VRF namevrf-cfg-name
Virtual Router Contextvrf
(Optional) Negate a command or set its defaultsno
Command Mode
• /exec/configure/router-bgp/router-bgp-bmp-server
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4896
V Commandsvrf
Page 5041
vrf[no] vrf <vrf-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Virtual Router Contextvrf
VRF namevrf-name
Command Mode
• /exec/configure/router-bgp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4897
V Commandsvrf
Page 5042
vrf[no] vrf <vrf-name>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure vrf for PLB servicevrf
VRF namevrf-name
Command Mode
• /exec/configure/plb
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4898
V Commandsvrf
Page 5043
vrf{ { no | default } vrf |
Syntax Description
no
Set a command to its defaultsdefault
Configure IP SLAs for a VPN Routing/Forwarding instancevrf
Command Mode
• /exec/configure/ip-sla/udp /exec/configure/ip-sla/jitter /exec/configure/ip-sla/tcp/exec/configure/ip-sla/icmpEcho /exec/configure/ip-sla/dns /exec/configure/ip-sla/http
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4899
V Commandsvrf
Page 5044
vrf{ { vrf { <vrf-name> | <vrf-known-name> } } | no vrf }
Syntax Description
Negate a command or set its defaultsno
Display per-VRF informationvrf
VRF namevrf-name
Known VRF namevrf-known-name
Command Mode
• /exec/configure/configngoamconnectcheck
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4900
V Commandsvrf
Page 5045
vrf contextvrf context <vrf-name> | no vrf context { <vrf-name> | <vrf-name> }
Syntax Description
Negate a command or set its defaultsno
Configure VRF parametersvrf
Create VRF and enter VRF modecontext
VRF namevrf-name
VRF namevrf-name
VRF namevrf-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4901
V Commandsvrf context
Page 5046
vrf default static{ vrf default { static <profile-name> | dynamic } } | { no vrf default }
Syntax Description
Negate a command or set its defaultsno
VRF namevrf
Default (wildcard). Match any vrf when there is no specific vrf mappingconfigured
default
Static Profile Map: Configure profile name via CLIstatic
Static Profile Map: Configure profile name via CLIprofile-name
Dynamic Profile Map: Retrieve profile name from the external serverdynamic
Command Mode
• /exec/configure/profile-map-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4902
V Commandsvrf default static
Page 5047
vrf membervrf member <vrf-name> | no vrf member [ <vrf-name> ]
Syntax Description
Negate a command or set its defaultsno
Configure VRF parametersvrf
Set interface's VRF membershipmember
VRF namevrf-name
Command Mode
• /exec/configure/if-igp /exec/configure/if-mgmt-ether
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4903
V Commandsvrf member
Page 5048
vrf membervrf member { <vrf_name> | <vrf-known-name> } | no vrf member [ <vrf_name> | <vrf-known-name> ]
Syntax Description
Negate a command or set its defaultsno
Configure VPN Routing/Forwarding tablevrf
Set route's VRF membershipmember
VRF namevrf_name
Known VRF namevrf-known-name
Command Mode
• /exec/configure/track
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4904
V Commandsvrf member
Page 5049
vrf static{ vrf <vrf-name> { static <profile-name> | dynamic } } | { no vrf <vrf-name> }
Syntax Description
Negate a command or set its defaultsno
VRF namevrf
VRF namevrf-name
Static Profile Map: Configure profile name via CLIstatic
Static Profile Map: Configure profile name via CLIprofile-name
Dynamic Profile Map: Retrieve profile name from the external serverdynamic
Command Mode
• /exec/configure/profile-map-global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4905
V Commandsvrf static
Page 5050
vrrp[no] vrrp <vr_id>
Syntax Description
(Optional) Negate a command or set its defaultsno
VRRP configuration commandsvrrp
IPv4 VR group numbervr_id
Command Mode
• /exec/configure/if-legacy-eth /exec/configure/if-ethernet /exec/configure/if-port-channel/exec/configure/if-vlan-common /exec/configure/if-eth-any
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4906
V Commandsvrrp
Page 5051
vrrp bfd{ vrrp bfd <peer_intf_ip> | no vrrp bfd [ <peer_intf_ip> ] }
Syntax Description
VRRP configuration commandsvrrp
BFD protocolbfd
Neighbor IP addresspeer_intf_ip
Negate a command or set its defaultsno
Command Mode
• /exec/configure/if-eth-any/vrrp
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4907
V Commandsvrrp bfd
Page 5052
vrrpv2[no] vrrpv2
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable VRRPv2 compatibility modevrrpv2
Command Mode
• /exec/configure/if-eth-any/vrrpv3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4908
V Commandsvrrpv2
Page 5053
vrrpv3[no] vrrpv3
Syntax Description
(Optional) Negate a command or set its defaultsno
VRRPv3 configuration commandsvrrpv3
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4909
V Commandsvrrpv3
Page 5054
vrrpv3 address-family[no] vrrpv3 <group_id> address-family <opt_v6>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure VRRPv3 group parametersvrrpv3
IPV6 address familyaddress-family
Enter ipv6opt_v6
VRRP Group IDgroup_id
Command Mode
• /exec/configure/if-eth-any /exec/configure/if-vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4910
V Commandsvrrpv3 address-family
Page 5055
vrrpv3 address-family[no] vrrpv3 <group_id> address-family <opt_v4>
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure VRRPv3 group parametersvrrpv3
IPV4 address familyaddress-family
Enter ipv4opt_v4
VRRP Group IDgroup_id
Command Mode
• /exec/configure/if-eth-any /exec/configure/if-vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4911
V Commandsvrrpv3 address-family
Page 5056
vrrs leader[no] vrrs leader <tag>
Syntax Description
(Optional) Negate a command or set its defaultsno
VRRS-related commandsvrrs
Name of VRRS tag for which this group is the leaderleader
VRRS tag to leadtag
Command Mode
• /exec/configure/if-eth-any/vrrpv3
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4912
V Commandsvrrs leader
Page 5057
vrrs pathway[no] vrrs pathway <name>
Syntax Description
(Optional) Negate a command or set its defaultsno
VRRS Interface configuration commandsvrrs
Configure a VRRS pathwaypathway
Name of the VRRS tag to associate with pathwayname
Command Mode
• /exec/configure/if-eth-any /exec/configure/if-vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4913
V Commandsvrrs pathway
Page 5058
vsh| vsh
Syntax Description
Pipe command output to filter|
the shell that understands cli commandvsh
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4914
V Commandsvsh
Page 5059
vtp[no] vtp
Syntax Description
(Optional) Negate a command or set its defaultsno
Enable VTP on this interfacevtp
Command Mode
• /exec/configure/if-switching
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4915
V Commandsvtp
Page 5060
vtp domainvtp domain <domain_name>
Syntax Description
Configure global VTP statevtp
Set the name of the VTP administrative domaindomain
The ascii name for the VTP administrative domaindomain_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4916
V Commandsvtp domain
Page 5061
vtp filevtp file <file_name> | no vtp file
Syntax Description
Negate a command or set its defaultsno
Configure global VTP statevtp
Set the name of the VTP file namefile
URI for vlan.datfile_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4917
V Commandsvtp file
Page 5062
vtp modevtp mode <mode-name> | no vtp mode
Syntax Description
Negate a command or set its defaultsno
Configure global VTP statevtp
Configure VTP device modemode
mode-name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4918
V Commandsvtp mode
Page 5063
vtp passwordvtp password <password_name> | no vtp password
Syntax Description
Negate a command or set its defaultsno
Configure global VTP statevtp
Set the password for the VTP administrative domainpassword
The ascii password for the VTP administrative domainpassword_name
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4919
V Commandsvtp password
Page 5064
vtp pruningvtp pruning | no vtp pruning
Syntax Description
Negate a command or set its defaultsno
Configure global VTP statevtp
Set the adminstrative domain to permit pruningpruning
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4920
V Commandsvtp pruning
Page 5065
vtp versionvtp version <version_num> | no vtp version
Syntax Description
Negate a command or set its defaultsno
Configure global VTP statevtp
Set the adminstrative domain to VTP versionversion
Set the adminstrative domain to VTP versionversion_num
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4921
V Commandsvtp version
Page 5066
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4922
V Commandsvtp version
Page 5067
W Commands
• wait-igp-convergence, on page 4924• watch, on page 4925• watch service action apply-acl, on page 4926• watchlist, on page 4927• watchlist, on page 4928• wc, on page 4929• wedge bmc ip-addr, on page 4930• weight, on page 4931• weight, on page 4932• weight, on page 4933• weight, on page 4934• where, on page 4935• where detail, on page 4936• window-size, on page 4937• wred-queue qos-group-map queue-only, on page 4938• write erase, on page 4939• write erase boot, on page 4940• write erase debug, on page 4941• write erase poap, on page 4942• wrr-queue qos-group-map, on page 4943• wrr unicast-bandwidth, on page 4944• wwn vsan vsan-wwn, on page 4945
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4923
Page 5068
wait-igp-convergence[no] wait-igp-convergence
Syntax Description
(Optional) Negate a command or set its defaultsno
Delay initial bestpath until redistributed IGPs have convergedwait-igp-convergence
Command Mode
• /exec/configure/router-bgp/router-bgp-af-ipv4 /exec/configure/router-bgp/router-bgp-vrf-af-ipv4/exec/configure/router-bgp/router-bgp-af-ipv6 /exec/configure/router-bgp/router-bgp-vrf-af-ipv6
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4924
W Commandswait-igp-convergence
Page 5069
watchwatch [ differences ] [ interval <time> ] <watch_cmd>
Syntax Description
execute a program periodicallywatch
(Optional) highlight the differencesdifferences
(Optional) watch intervalinterval
(Optional) interval in secondstime
enter the command you want to watchwatch_cmd
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4925
W Commandswatch
Page 5070
watch service action apply-acl[no] watch service <service-name> action apply-acl <acl-name> | no watch service
Syntax Description
(Optional) Negate a command or set its defaultsno
Watch a pod/servicewatch
The pod or service to watchservice
Name of the service/pod to watchservice-name
Action to be appliedaction
Change ACL configapply-acl
Name of the acl to applyacl-name
Command Mode
• /exec/configure/kubernetes
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4926
W Commandswatch service action apply-acl
Page 5071
watchlist[no] watchlist <watchlistname>
Syntax Description
Specify POSTCARD watchlist to usewatchlist
Name of watchlistwatchlistname
Command Mode
• /exec/configure/config-postcard-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4927
W Commandswatchlist
Page 5072
watchlist[no] watchlist <watchlistname>
Syntax Description
Specify INT watchlist to usewatchlist
Name of watchlistwatchlistname
Command Mode
• /exec/configure/config-int-monitor
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4928
W Commandswatchlist
Page 5073
wc| wc [ -c | -l | -w ]
Syntax Description
Pipe command output to filter|
Count words, lines, characterswc
(Optional) Output character count-c
(Optional) Output line count-l
(Optional) Output word count-w
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4929
W Commandswc
Page 5074
wedge bmc ip-addr[no] wedge bmc ip-addr { <ip> | <ip_v6> }
Syntax Description
(Optional) Negate a command or set its defaultsno
Configure wedge Board Management controller ip addresswedge
Board Management Controller ip addressbmc
BMC ip addressip-addr
ip adddressip
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4930
W Commandswedge bmc ip-addr
Page 5075
weight{ weight <weight> } | { { no | default } weight [ <weight> ] }
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Set default weight for routes from this neighborweight
Default weightweight
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-mdt
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4931
W Commandsweight
Page 5076
weight[no] weight <weight-value>
Syntax Description
(Optional) Negate a command or set its defaultsno
weight for traffic distributionweight
weight valueweight-value
Command Mode
• /exec/configure/itd-dg-node
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4932
W Commandsweight
Page 5077
weight{ weight <weight> } | { { no | default } weight [ <weight> ] }
Syntax Description
Negate a command or set its defaultsno
Inherit values from a peer templatedefault
Set default weight for routes from this neighborweight
Default weightweight
Command Mode
• /exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv4/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-vpnv6/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv4-label/exec/configure/router-bgp/router-bgp-neighbor/router-bgp-neighbor-af-ipv6-label
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4933
W Commandsweight
Page 5078
weightweight <weight-value> | no weight
Syntax Description
Negate a command or set its defaultsno
Configure weight of node for traffic distributionweight
weight valueweight-value
Command Mode
• /exec/configure/plb-dg-node
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4934
W Commandsweight
Page 5079
wherewhere
Syntax Description
shows the cli context you are inwhere
Command Mode
• /global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4935
W Commandswhere
Page 5080
where detailwhere detail
Syntax Description
shows the cli context you are inwhere
shows each entry on separate linedetail
Command Mode
• /global
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4936
W Commandswhere detail
Page 5081
window-size[no] window-size <size>
Syntax Description
Configure Window sizewindow-size
window size valuesize
Command Mode
• /exec/configure/macsec-policy
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4937
W Commandswindow-size
Page 5082
wred-queue qos-group-map queue-only[no] wred-queue qos-group-map queue-only { <qid> }
Syntax Description
(Optional) Negate the commandno
Enable queue based ECN marking for specific qos-groupwred-queue
Enable queue based ECN markingqueue-only
Qid valueqos-group-map
Provide qos-group valueqid
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4938
W Commandswred-queue qos-group-map queue-only
Page 5083
write erasewrite erase
Syntax Description
Write current configurationwrite
Destroys the configuration on persistent mediaerase
Command Mode
• /exec
Usage Guidelines
You can erase the configuration on your device to return to the configuration defaults. In this context,configuration refers to the startup configuration as displayed by the show startup command. No other internalapplication or process states are cleared. To remove all application persistency files such as patch rpms, thirdparty rpms, and application configuration in the /etc directory other than configuration, use the install resetcommand.
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4939
W Commandswrite erase
Page 5084
write erase bootwrite erase boot
Syntax Description
Write current configurationwrite
Destroys the configuration on persistent mediaerase
Destroys boot configuration on persistent mediaboot
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4940
W Commandswrite erase boot
Page 5085
write erase debugwrite erase debug
Syntax Description
Write current configurationwrite
Destroys the configuration on persistent mediaerase
Destroys debug configuration on persistent mediadebug
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4941
W Commandswrite erase debug
Page 5086
write erase poapwrite erase poap
Syntax Description
Write current configurationwrite
Destroys the configuration on persistent mediaerase
Removes System-wide POAP disable configuration on persistent mediapoap
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4942
W Commandswrite erase poap
Page 5087
wrr-queue qos-group-map[no] wrr-queue qos-group-map <qid> { <cos> } +
Syntax Description
(Optional) Negate the commandno
Map traffic priority (QG) values to L3 Multicast Queueswrr-queue
Qid valueqos-group-map
Provide qid valueqid
Provide qos-group-map valuecos
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4943
W Commandswrr-queue qos-group-map
Page 5088
wrr unicast-bandwidth[no] wrr unicast-bandwidth <bw>
Syntax Description
(Optional) Negate the commandno
Configure Unicast Traffic Bandwidth Percentagewrr
Specify rate as percentage of interface data-rateunicast-bandwidth
Value in percentage (Default is set to 50)bw
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4944
W Commandswrr unicast-bandwidth
Page 5089
wwn vsan vsan-wwnwwn vsan <i0> vsan-wwn <wwn1> | no
Syntax Description
<i0>vsan
Negate a command or set its defaultsno
Set secondary base MAC addr and range for additional WWNswwn
Enter the vsan idi0
vsan-wwn for vsan in interop mode 4vsan-wwn
Enter wwn for vsan in interop mode 4wwn1
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4945
W Commandswwn vsan vsan-wwn
Page 5090
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4946
W Commandswwn vsan vsan-wwn
Page 5091
X Commands
• xconnect, on page 4948• xml, on page 4949• xml, on page 4950• xml server max-session, on page 4951• xml server rm-shm, on page 4952• xml server terminate session, on page 4953• xml server timeout, on page 4954• xml server validate, on page 4955• xml server xml-debug, on page 4956• xmlagent, on page 4957• xmlin, on page 4958• xmlin, on page 4959• xmlin, on page 4960• xmlin, on page 4961• xmlout, on page 4962
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4947
Page 5092
xconnectxconnect | no xconnect
Syntax Description
Negate a command or set its defaultsno
Enable cross connect on this VLANxconnect
Command Mode
• /exec/configure/vlan
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4948
X Commandsxconnect
Page 5093
xml| xml
Syntax Description
Pipe command output to filter|
output in xml format (according to .xsd definitions)xml
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4949
X Commandsxml
Page 5094
xml| xml
Syntax Description
Pipe command output to filter|
output in xml format (according to .xsd definitions)xml
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4950
X Commandsxml
Page 5095
xml server max-session[no] xml server max-session <number>
Syntax Description
(Optional) Negate a command or set its defaultsno
xml agentxml
xml agent serverserver
configure maximum number of xml sessions allowedmax-session
number of the sessionsnumber
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4951
X Commandsxml server max-session
Page 5096
xml server rm-shmxml server rm-shm
Syntax Description
xml agentxml
xml agent serverserver
remove shmem. SHOULD BE USED WITH CAUTIONrm-shm
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4952
X Commandsxml server rm-shm
Page 5097
xml server terminate sessionxml server terminate session <session_id>
Syntax Description
xml agentxml
xml agent serverserver
command to terminate an XML sessionterminate
terminate an XML sessionsession
sessions numbersession_id
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4953
X Commandsxml server terminate session
Page 5098
xml server timeout[no] xml server timeout <value> [ <session_id> ]
Syntax Description
(Optional) Negate a command or set its defaultsno
xml agentxml
xml agent serverserver
configure xml agent session timeouttimeout
timeout in secondsvalue
(Optional) xml agent session idsession_id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4954
X Commandsxml server timeout
Page 5099
xml server validate[no] xml server validate { all | <session_id> }
Syntax Description
(Optional) Negate a command or set its defaultsno
xml agentxml
xml agent serverserver
command to validate an XML sessionvalidate
all sessionsall
session numbersession_id
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4955
X Commandsxml server validate
Page 5100
xml server xml-debug[no] xml server xml-debug
Syntax Description
(Optional) Negate a command or set its defaultsno
xml agentxml
xml serverserver
xml server xml-debugxml-debug
Command Mode
• /exec/configure
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4956
X Commandsxml server xml-debug
Page 5101
xmlagentxmlagent
Syntax Description
to run xmlagentxmlagent
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4957
X Commandsxmlagent
Page 5102
xmlinxmlin
Syntax Description
Convert CLI commands to their XML formatsxmlin
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4958
X Commandsxmlin
Page 5103
xmlin| xmlin
Syntax Description
Pipe command output to filter|
Convert CLI show commands to their XML formatsxmlin
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4959
X Commandsxmlin
Page 5104
xmlinxmlin
Syntax Description
Convert CLI commands to their XML formatsxmlin
Command Mode
• /exec
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4960
X Commandsxmlin
Page 5105
xmlin| xmlin
Syntax Description
Pipe command output to filter|
Convert CLI show commands to their XML formatsxmlin
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4961
X Commandsxmlin
Page 5106
xmlout| xmlout
Syntax Description
Pipe command output to filter|
output in xml format (according to the latest .xsd version)xmlout
Command Mode
• /output
Cisco Nexus 3400-S Series NX-OS Command Reference (Configuration Commands), Release 9.2(2)4962
X Commandsxmlout