-
Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages ReferenceJuly 2014
Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan
Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000
800 553-NETS (6387)Fax: 408 527-0883
Text Part Number: OL-29318-02
http://www.cisco.com
-
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN
THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE
ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION
OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING
PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU
ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an
adaptation of a program developed by the University of California,
Berkeley (UCB) as part of UCB’s public domain version of the UNIX
operating system. All rights reserved. Copyright © 1981, Regents of
the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES
AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL
FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION,
THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR
TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY
INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING
OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR
ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
Cisco and the Cisco logo are trademarks or registered trademarks
of Cisco and/or its affiliates in the U.S. and other countries. To
view a list of Cisco trademarks, go to this URL:
www.cisco.com/go/trademarks. Third-party trademarks mentioned are
the property of their respective owners. The use of the word
partner does not imply a partnership relationship between Cisco and
any other company. (1110R)
Any Internet Protocol (IP) addresses used in this document are
not intended to be actual addresses. Any examples, command display
output, and figures included in the document are shown for
illustrative purposes only. Any use of actual IP addresses in
illustrative content is unintentional and coincidental.
Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference© 2013-2014 Cisco Systems, Inc. All rights
reserved.
http://www.cisco.com/go/trademarks
-
CisOL-29318-02
C O N T E N T S
Preface xvii
Audience xvii
Organization xvii
Document Conventions xviii
Documentation Feedback xviii
Obtaining Documentation and Submitting a Service Request xix
C H A P T E R 1 Introduction to System Messages for Cisco NX-OS
1-1
System Log Message Format 1-1Syslog Format On a Resident Switch
1-1Syslog Format On a Remote-Logging Server 1-3
Capturing System Messages and History 1-5Saving the System
Messages Log 1-5Logging System Messages to a Syslog Server 1-5
C H A P T E R 2 System Messages and Recovery Procedures for the
Cisco MDS 9000 and Nexus 7000 Family 2-1AAA Messages 2-1
AAA-1 2-1AAA-2 2-1AAA-3 2-2AAA-6 2-2
AAM Messages 2-2AAM-2 2-2AAM-3 2-2
ACLLOG Messages 2-3ACLLOG-4 2-3ACLLOG-6 2-3
ACLMGR Messages 2-3ACLMGR-2 2-4ACLMGR-3 2-5ACLMGR-4 2-6ACLMGR-6
2-7
ACLQOS Messages 2-8ACLQOS-SLOT#-2 2-8
ico MDS 9000 Family and Nexus 7000 Series NX-OS System Messages
Reference
-
Contents
ACLQOS-SLOT#-3 2-8ACLQOS-SLOT#-4 2-9ACLQOS-SLOT#-5 2-10
ACLTCAM Messages 2-11ACLTCAM-2 2-11ACLTCAM-3 2-14ACLTCAM-4
2-16ACLTCAM-6 2-17
ACL Messages 2-17ACL-2 2-17ACL-3 2-19ACL-4 2-19ACL-5 2-20ACL-6
2-20
AGNI-DPP Messages 2-21AGNI-DPP-2 2-21AGNI-DPP-6 2-22
AGNIL2F Messages 2-22AGNIL2F-6 2-22
ALI_LC Messages 2-23ALI_LC-2 2-23
AMM Messages 2-23AMM-SLOT#-0 2-23AMM-SLOT#-2 2-24AMM-SLOT#-6
2-24
APP EMULATOR Messages 2-24APP EMULATOR-SLOT#-5 2-24
ARBITER Messages 2-25ARBITER-2 2-25
ASCII-CFG Messages 2-25ASCII-CFG-2 2-26ASCII-CFG-3
2-27ASCII-CFG-6 2-27
ASSOC MGR Messages 2-28ASSOC MGR-0 2-28ASSOC MGR-1 2-29ASSOC
MGR-2 2-29ASSOC MGR-3 2-29ASSOC MGR-4 2-29ASSOC MGR-5 2-29
iiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
ASSOC MGR-6 2-30ASSOC MGR-7 2-31
ATLANTIS_APP Messages 2-31ATLANTIS_APP-SLOT#-2 2-31
AZUMA Messages 2-31AZUMA-2 2-31AZUMA-6 2-32
BET Messages 2-32BET-6 2-32
BFDC Messages 2-32BFDC-SLOT#-2 2-32
BFD Messages 2-33BFD-3 2-33BFD-4 2-33BFD-5 2-34BFD-6 2-35
BIOS DAEMON Messages 2-36BIOS DAEMON-2 2-36BIOS DAEMON-5
2-36BIOS DAEMON-SLOT#-2 2-36BIOS DAEMON-SLOT#-5 2-37
BLOGGERD Messages 2-37BLOGGERD-2 2-37BLOGGERD-3 2-37BLOGGERD-4
2-39BLOGGERD-6 2-39
2-39
BOOTUP TEST Messages 2-39BOOTUP TEST-2 2-39
BOOTVAR Messages 2-40BOOTVAR-2 2-40BOOTVAR-3 2-41BOOTVAR-5
2-42BOOTVAR-6 2-43
CALLHOME Messages 2-43CALLHOME-2 2-44CALLHOME-3 2-44CALLHOME-6
2-45
CARDCLIENT Messages 2-45CARDCLIENT-2 2-45
iiiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
CARDCLIENT-3 2-46CARDCLIENT-SLOT#-2 2-46
2-46
CDP Messages 2-46CDP-2 2-47CDP-3 2-47CDP-4 2-48CDP-5 2-49CDP-6
2-49
CERT_ENROLL Messages 2-50CERT_ENROLL-2 2-50CERT_ENROLL-3
2-51CERT_ENROLL-6 2-51
CFGD Messages 2-51CFGD-SLOT#-2 2-51
CFS Messages 2-51CFS-2 2-52CFS-3 2-53CFS-4 2-55CFS-6 2-55
CIMSRVPROV Messages 2-58CIMSRVPROV-2 2-58CIMSRVPROV-3
2-58CIMSRVPROV-6 2-59
CLIS Messages 2-59CLIS-5 2-59CLIS-6 2-60
CLK_MGR Messages 2-60CLK_MGR-2 2-60CLK_MGR-5 2-60CLK_MGR-6
2-60
CLOUD Messages 2-61CLOUD-2 2-61CLOUD-3 2-61CLOUD-6 2-62
CLP_FWD Messages 2-62CLP_FWD-6 2-62
CLP_L3 Messages 2-62CLP_L3-6 2-62
CLP_MAC Messages 2-62
ivCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
CLP_MAC-6 2-63CLP_XBAR Messages 2-63
CLP_XBAR-2 2-63CLP_XBAR-6 2-63
CLUSTER_TEST_APP Messages 2-63CLUSTER_TEST_APP-5 2-63
CLUSTER Messages 2-64CLUSTER-2 2-64CLUSTER-5 2-67
CMOND Messages 2-69CMOND-2 2-69
CMPPROXY Messages 2-70CMPPROXY-2 2-70CMPPROXY-5 2-70CMPPROXY-6
2-71
COPP Messages 2-71COPP-1 2-71COPP-2 2-71COPP-3 2-72COPP-4
2-73COPP-5 2-73COPP-6 2-74COPP-7 2-74
CORE-DMON Messages 2-75CORE-DMON-2 2-75CORE-DMON-3 2-75
CRDCFG Messages 2-75CRDCFG-2 2-75CRDCFG-3 2-76CRDCFG-SLOT#-2
2-76
2-76
CREDITMON Messages 2-76CREDITMON-SLOT#-2 2-77
CTS Messages 2-77CTS-2 2-77CTS-3 2-80CTS-5 2-80CTS-6 2-80CTS-7
2-83
DCEFIB Messages 2-84
vCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
DCEFIB-SLOT#-0 2-84DCEFIB-SLOT#-2 2-84DCEFIB-SLOT#-6 2-85
DEBUGPROXY Messages 2-85DEBUGPROXY-6 2-85
DEVICE-ALIAS Messages 2-85DEVICE-ALIAS-2 2-86DEVICE-ALIAS-3
2-86DEVICE-ALIAS-6 2-89
DEVICE_TEST Messages 2-91DEVICE_TEST-2 2-92DEVICE_TEST-3
2-94DEVICE_TEST-4 2-95DEVICE_TEST-5 2-96DEVICE_TEST-6 2-96
DEV_LOG_SUP Messages 2-96DEV_LOG_SUP-3 2-96
2-96
DEV_LOG Messages 2-96DEV_LOG-3 2-96DEV_LOG-SLOT#-4 2-97
DFTM Messages 2-97DFTM-SLOT#-2 2-97DFTM-SLOT#-3 2-98
DHCP_SNOOP Messages 2-99DHCP_SNOOP-2 2-100DHCP_SNOOP-3
2-100DHCP_SNOOP-4 2-102DHCP_SNOOP-5 2-104DHCP_SNOOP-6 2-105
DIAGCLIENT Messages 2-106DIAGCLIENT-2 2-107DIAGCLIENT-3
2-107DIAGCLIENT-4 2-107DIAGCLIENT-5 2-108DIAGCLIENT-7 2-109
DIAGMGR Messages 2-109DIAGMGR-2 2-109DIAGMGR-3 2-110DIAGMGR-4
2-110
viCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
DIAGMGR-5 2-111DIAGMGR-6 2-112
DIAG_PORT_LB Messages 2-112DIAG_PORT_LB-2 2-113DIAG_PORT_LB-3
2-114DIAG_PORT_LB-4 2-117DIAG_PORT_LB-5 2-117
DMM Messages 2-118DMM-SLOT#-2 2-118DMM-SLOT#-5 2-118
DOT1X Messages 2-120DOT1X-2 2-120DOT1X-3 2-120DOT1X-4
2-122DOT1X-5 2-123DOT1X-6 2-124
DPP_DEBUG Messages 2-124DPP_DEBUG-2 2-125
DPVM Messages 2-125DPVM-2 2-125DPVM-3 2-125DPVM-4 2-126DPVM-6
2-126
DSTATS Messages 2-127DSTATS-2 2-127DSTATS-3 2-127
DT_HELPER Messages 2-129DT_HELPER-2 2-129
ELTMC Messages 2-129ELTMC-2 2-129
ELTM Messages 2-132ELTM-2 2-132ELTM-3 2-133ELTM-5 2-133ELTM-6
2-134
EOU Messages 2-134EOU-2 2-134EOU-5 2-134EOU-6 2-134EOU-7
2-136
viiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
EPLD_AUTO Messages 2-137EPLD_AUTO-2 2-137
EPLD_UPGRADE Messages 2-137EPLD_UPGRADE-2 2-137
EPP Messages 2-138EPP-5 2-138
ETH-PORT-SEC Messages 2-138ETH-PORT-SEC-3 2-138ETH-PORT-SEC-5
2-140
ETHPORT Messages 2-140ETHPORT-2 2-141ETHPORT-3 2-141ETHPORT-4
2-143ETHPORT-5 2-143
ETH_PORT_CHANNEL Messages 2-154ETH_PORT_CHANNEL-1
2-154ETH_PORT_CHANNEL-2 2-155ETH_PORT_CHANNEL-3
2-155ETH_PORT_CHANNEL-4 2-158ETH_PORT_CHANNEL-5
2-158ETH_PORT_CHANNEL-6 2-161ETH_PORT_CHANNEL-7 2-161
EUREKA_USD Messages 2-162EUREKA_USD-3 2-162
EVMC Messages 2-162EVMC-3 2-162EVMC-4 2-162EVMC-5 2-163
EVMED Messages 2-163EVMED-2 2-163EVMED-5 2-163
EVMS Messages 2-164EVMS-2 2-164EVMS-4 2-164EVMS-6 2-165
EXAMPLE_TEST Messages 2-165EXAMPLE_TEST-5 2-165
EXCEPTIONLOG Messages 2-165EXCEPTIONLOG-SLOT#-2 2-165
EX_SYSLOG Messages 2-165
viiiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
EX_SYSLOG-0 2-166EX_SYSLOG-1 2-166EX_SYSLOG-2 2-166EX_SYSLOG-3
2-166EX_SYSLOG-4 2-166EX_SYSLOG-5 2-167EX_SYSLOG-6 2-167EX_SYSLOG-7
2-167
F16_CMN_USD Messages 2-167F16_CMN_USD-6 2-167
F16_FWD_USD Messages 2-167F16_FWD_USD-6 2-168
F16_MAC_USD Messages 2-168F16_MAC_USD-3 2-168F16_MAC_USD-6
2-168
F16_QUE_USD Messages 2-168F16_QUE_USD-6 2-168
F16_XBAR_USD Messages 2-169F16_XBAR_USD-6 2-169
FABRICPATH Messages 2-169FABRICPATH-2 2-169FABRICPATH-4
2-169FABRICPATH-6 2-170
FALCON Messages 2-171FALCON-SLOT#-2 2-171
FC-REDIRECT Messages 2-171FC-REDIRECT-2 2-172FC-REDIRECT-3
2-178FC-REDIRECT-5 2-187
FC-TUNNEL Messages 2-191FC-TUNNEL-3 2-191FC-TUNNEL-5 2-193
FCC_LC Messages 2-194FCC_LC-2 2-194FCC_LC-5 2-194FCC_LC-6
2-195
FCC Messages 2-195FCC-2 2-195FCC-5 2-195FCC-6 2-196
ixCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
FCDDH Messages 2-197FCDDH-SLOT#-3 2-197FCDDH-SLOT#-4
2-197FCDDH-SLOT#-5 2-197
FCDD Messages 2-197FCDD-SLOT#-3 2-197FCDD-SLOT#-4
2-198FCDD-SLOT#-5 2-198FCDD-SLOT#-7 2-199
FCDOMAIN Messages 2-199FCDOMAIN-2 2-199FCDOMAIN-3
2-202FCDOMAIN-4 2-204FCDOMAIN-5 2-205FCDOMAIN-6 2-206FCDOMAIN-7
2-212
FCD Messages 2-214FCD-7 2-214
FCFWD Messages 2-215FCFWD-3 2-215FCFWD-4 2-215FCFWD-6 2-215
FCNS Messages 2-215FCNS-2 2-216FCNS-3 2-216FCNS-4 2-217FCNS-6
2-217
FCOE_MGR Messages 2-218FCOE_MGR-2 2-218FCOE_MGR-5 2-218
FCOE Messages 2-219FCOE-5 2-219
FCSP-MGR Messages 2-220FCSP-MGR-2 2-220
FCS Messages 2-222FCS-2 2-222FCS-3 2-223FCS-5 2-224FCS-6
2-224
FDMI Messages 2-225
xCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
FDMI-2 2-225FDMI-3 2-226FDMI-4 2-227FDMI-6 2-227
FEATURE-MGR Messages 2-227FEATURE-MGR-2 2-227FEATURE-MGR-6
2-230
FEX Messages 2-231FEX-2 2-231FEX-4 2-232FEX-5 2-232
FIB Messages 2-233FIB-SLOT#-0 2-233FIB-SLOT#-1 2-233FIB-SLOT#-2
2-234FIB-SLOT#-3 2-234FIB-SLOT#-4 2-235FIB-SLOT#-6 2-236
FICON Messages 2-236FICON-2 2-237FICON-3 2-237FICON-5
2-239FICON-6 2-239
FIPSM Messages 2-239FIPSM-5 2-240
FIPS Messages 2-240FIPS-0 2-240FIPS-6 2-240
FLN_EM Messages 2-240FLN_EM-6 2-241
FLN_FCP Messages 2-241FLN_FCP-6 2-241FLN_FCP-SLOT#-2
2-241FLN_FCP-SLOT#-3 2-241FLN_FCP-SLOT#-4 2-242
FLN_FWD_USD Messages 2-243FLN_FWD_USD-2 2-243FLN_FWD_USD-6
2-243
FLN_L3 Messages 2-243FLN_L3-6 2-244
xiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
FLN_QUE Messages 2-244FLN_QUE-6 2-244
FLN_XBAR Messages 2-244FLN_XBAR-2 2-244FLN_XBAR-6 2-244
FLOGI Messages 2-245FLOGI-1 2-245FLOGI-2 2-246FLOGI-4
2-246FLOGI-5 2-246
FS-DAEMON Messages 2-247FS-DAEMON-2 2-247FS-DAEMON-6 2-247
FSCM Messages 2-248FSCM-2 2-248
FSPF Messages 2-248FSPF-2 2-248FSPF-2 2-249FSPF-4 2-251FSPF-5
2-252FSPF-6 2-252FSPF-7 2-254
FVP Messages 2-254FVP-2 2-254FVP-3 2-255FVP-4 2-256FVP-6
2-256
GARUDA_USD Messages 2-258GARUDA_USD-6 2-258
GLBP Messages 2-258GLBP-2 2-258GLBP-3 2-258GLBP-4 2-260GLBP-5
2-261
HSRP_ENGINE Messages 2-263HSRP_ENGINE-3 2-264HSRP_ENGINE-4
2-265HSRP_ENGINE-5 2-266HSRP_ENGINE-6 2-268
IDEHSD Messages 2-268
xiiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
IDEHSD-1 2-268IDEHSD-2 2-268IDEHSD-3 2-270IDEHSD-5 2-270IDEHSD-6
2-270IDEHSD-7 2-271
IFTMC Messages 2-271IFTMC-SLOT#-1 2-271IFTMC-SLOT#-2 2-271
IKE Messages 2-274IKE-3 2-274IKE-4 2-276IKE-6 2-277
ILC-SPAN Messages 2-277ILC-SPAN-3 2-277
ILC_HELPER Messages 2-277ILC_HELPER-2 2-277ILC_HELPER-3
2-277ILC_HELPER-6 2-278
IMAGE_DNLD Messages 2-278IMAGE_DNLD-SLOT#-2
2-278IMAGE_DNLD-SLOT#-4 2-279IMAGE_DNLD-SLOT#-5 2-279
IMAGE_UPGRADE Messages 2-280IMAGE_UPGRADE-SLOT#-2
2-280IMAGE_UPGRADE-SLOT#-4 2-280
IM Messages 2-280IM-3 2-280IM-5 2-281
INSTALLER Messages 2-281INSTALLER-1 2-281INSTALLER-5 2-282
INTERFACE_VLAN Messages 2-282INTERFACE_VLAN-4
2-282INTERFACE_VLAN-5 2-283
IOA_LC Messages 2-285IOA_LC-5 2-285
IPACL Messages 2-285IPACL-0 2-285IPACL-1 2-286
xiiiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
IPACL-2 2-286IPACL-3 2-286IPACL-4 2-286IPACL-5 2-286IPACL-6
2-287
IPFC Messages 2-287IPFC-2 2-287IPFC-3 2-287IPFC-5 2-288IPFC-6
2-288
IPQOSMGR Messages 2-288IPQOSMGR-2 2-288IPQOSMGR-3
2-289IPQOSMGR-4 2-290IPQOSMGR-6 2-291
IPSEC Messages 2-291IPSEC-2 2-291IPSEC-3 2-291IPSEC-5 2-292
IPS_SB_MGR Messages 2-293IPS_SB_MGR-SLOT#-2
2-294IPS_SB_MGR-SLOT#-3 2-294IPS_SB_MGR-SLOT#-4
2-295IPS_SB_MGR-SLOT#-6 2-295
IPS Messages 2-295IPS-2 2-296IPS-3 2-296IPS-4 2-301IPS-5
2-302IPS-6 2-311IPS-7 2-311
IPV6 Messages 2-312IPV6-2 2-312IPV6-3 2-312IPV6-4 2-313IPV6-6
2-313
IP Messages 2-314IP-1 2-314IP-2 2-314IP-3 2-314
xivCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
IP-4 2-315IP-6 2-315
ISAPI Messages 2-316ISAPI-SLOT#-0 2-316ISAPI-SLOT#-1
2-317ISAPI-SLOT#-2 2-317ISAPI-SLOT#-3 2-318ISAPI-SLOT#-4
2-319ISAPI-SLOT#-5 2-319ISAPI-SLOT#-6 2-320ISAPI-SLOT#-7 2-321
ISCM Messages 2-322ISCM-2 2-322ISCM-3 2-322ISCM-4 2-323ISCM-5
2-324
ISNS Messages 2-324ISNS-2 2-324
IVR Messages 2-324IVR-2 2-325IVR-3 2-328IVR-4 2-336IVR-5
2-337IVR-6 2-340IVR-7 2-341
L2FMC Messages 2-341L2FMC-SLOT#-0 2-342L2FMC-SLOT#-2
2-342L2FMC-SLOT#-5 2-342L2FMC-SLOT#-6 2-343
L2FM Messages 2-344L2FM-0 2-344L2FM-1 2-344L2FM-2 2-346L2FM-4
2-346L2FM-5 2-347L2FM-6 2-347
L2MCAST Messages 2-347L2MCAST-SLOT#-0 2-347L2MCAST-SLOT#-2
2-348
xvCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
L2MCAST-SLOT#-3 2-348L2MCAST-SLOT#-6 2-349
L3VM Messages 2-349L3VM-5 2-350
LACP Messages 2-350LACP-3 2-350LACP-5 2-351
LC-FCFWD Messages 2-353LC-FCFWD-3 2-353
LC-QOS Messages 2-353LC-QOS-3 2-353
LC-SPAN Messages 2-353LC-SPAN-3 2-353
LC_CFG Messages 2-353LC_CFG-SLOT#-2 2-354
LC_MNT_MGR Messages 2-354LC_MNT_MGR-SLOT#-2 2-354
LC_PORT_CHANNEL Messages 2-354LC_PORT_CHANNEL-SLOT#-0
2-354LC_PORT_CHANNEL-SLOT#-1 2-355LC_PORT_CHANNEL-SLOT#-3 2-355
LC_PORT_MGR Messages 2-355LC_PORT_MGR-SLOT#-2 2-355
LC_RDL Messages 2-356LC_RDL-3 2-356LC_RDL-6 2-357
LDAP Messages 2-357LDAP-2 2-357LDAP-3 2-357LDAP-5 2-358LDAP-6
2-358
LDP Messages 2-358LDP-5 2-358
LED_MGR Messages 2-358LED_MGR-SLOT#-3 2-359
LIBBASE_SVC Messages 2-359LIBBASE_SVC-2 2-359LIBBASE_SVC-4
2-359LIBBASE_SVC-5 2-360
LIBGD Messages 2-360
xviCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
LIBGD-2 2-360LIBGD-3 2-361LIBGD-5 2-361LIBGD-6 2-361
LIBIFMGR Messages 2-362LIBIFMGR-5 2-362
LICMGR Messages 2-362LICMGR-0 2-362LICMGR-1 2-362LICMGR-2
2-363LICMGR-3 2-364LICMGR-4 2-365LICMGR-6 2-365
LIM Messages 2-366LIM-2 2-366
LIM Messages 2-367LIM-3 2-367
LIM Messages 2-368LIM-4 2-368
LIM Messages 2-369LIM-5 2-369
LIT Messages 2-379LIT-6 2-380
LLDP Messages 2-380LLDP-1 2-380LLDP-3 2-380LLDP-5 2-381LLDP-6
2-381
M2FIB Messages 2-381M2FIB-SLOT#-0 2-381M2FIB-SLOT#-2
2-382M2FIB-SLOT#-6 2-382
M2RIB Messages 2-383M2RIB-0 2-383M2RIB-2 2-383M2RIB-6 2-384
MAC Messages 2-385MAC-SLOT#-2 2-385
MCAST Messages 2-385MCAST-2 2-385
xviiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
MCAST-4 2-385MCAST-5 2-386
MCECTEST Messages 2-386MCECTEST-3 2-386MCECTEST-5
2-387MCECTEST-6 2-387
MCM Messages 2-387MCM-2 2-387MCM-5 2-388MCM-6 2-388
METROPOLIS_USD Messages 2-388METROPOLIS_USD-3 2-388
MFDM Messages 2-388MFDM-2 2-389
MODULE Messages 2-389MODULE-2 2-390MODULE-3 2-394MODULE-4
2-394MODULE-5 2-395MODULE-6 2-396
MONITOR Messages 2-396MONITOR-3 2-397MONITOR-5 2-397
MTM Messages 2-397MTM-SLOT#-0 2-398
MTM Messages 2-398MTM-SLOT#-1 2-398
MTM Messages 2-398MTM-SLOT#-2 2-398
MTM Messages 2-400MTM-SLOT#-5 2-400
MTM Messages 2-400MTM-SLOT#-6 2-400
NFM Messages 2-401NFM-2 2-401NFM-3 2-402NFM-4 2-403NFM-5
2-404NFM-6 2-404NFM-7 2-405
xviiiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
NFP Messages 2-405NFP-SLOT#-2 2-406NFP-SLOT#-5 2-407
NPC Messages 2-407NPC-SLOT#-3 2-407NPC-SLOT#-4 2-407NPC-SLOT#-5
2-407
NPV Messages 2-408NPV-2 2-408NPV-3 2-409NPV-4 2-412NPV-5
2-412NPV-6 2-413NPV-7 2-416
NTP Messages 2-417NTP-2 2-417NTP-3 2-417NTP-6 2-418
NVP Messages 2-418NVP-6 2-418NVP-SLOT#-2 2-419
OBFL Messages 2-419OBFL-3 2-419
OC_USD Messages 2-419OC_USD-2 2-419
ONEP Messages 2-419ONEP-2 2-420ONEP-3 2-421ONEP-4 2-423ONEP-6
2-423
ORI_FWD Messages 2-423ORI_FWD-2 2-423ORI_FWD-6 2-423
ORI_MAC Messages 2-423ORI_MAC-2 2-424ORI_MAC-6 2-424
ORI_XBAR_USD Messages 2-424ORI_XBAR_USD-2 2-424ORI_XBAR_USD-4
2-425ORI_XBAR_USD-6 2-425
xixCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
OTM Messages 2-425OTM-2 2-425OTM-3 2-425OTM-5 2-425OTM-6
2-426
PHY_USD Messages 2-426PHY_USD-SLOT#-4 2-427
PIXM Messages 2-427PIXM-2 2-427PIXM-3 2-427PIXM-4 2-427PIXM-7
2-428
PLATFORM Messages 2-428PLATFORM-0 2-428PLATFORM-1
2-431PLATFORM-2 2-432PLATFORM-3 2-444PLATFORM-4 2-446PLATFORM-5
2-446PLATFORM-6 2-448PLATFORM-7 2-448
PLOG_SUP Messages 2-449PLOG_SUP-4 2-449
PLOG Messages 2-449PLOG-4 2-449
PLSM Messages 2-449PLSM-3 2-449PLSM-6 2-450
PLTFM_CONFIG Messages 2-450PLTFM_CONFIG-3 2-450PLTFM_CONFIG-4
2-451
PLUGIN Messages 2-451PLUGIN-2 2-451PLUGIN-3 2-453
PMON Messages 2-453PMON-2 2-453PMON-3 2-454PMON-5 2-454PMON-6
2-454
POAP Messages 2-454
xxCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
POAP-2 2-454POAP-5 2-456
PONG Messages 2-456PONG-5 2-456
PORT-CHANNEL Messages 2-457PORT-CHANNEL-1 2-457PORT-CHANNEL-2
2-457PORT-CHANNEL-3 2-458PORT-CHANNEL-4 2-459PORT-CHANNEL-5
2-460PORT-CHANNEL-6 2-461PORT-CHANNEL-7 2-461
PORT-PROFILE Messages 2-462PORT-PROFILE-2 2-462PORT-PROFILE-3
2-462PORT-PROFILE-6 2-464
PORT-RESOURCES Messages 2-465PORT-RESOURCES-3
2-465PORT-RESOURCES-5 2-466
PORT-SECURITY Messages 2-466PORT-SECURITY-2 2-466PORT-SECURITY-3
2-466PORT-SECURITY-4 2-468PORT-SECURITY-6 2-469
PORT Messages 2-469PORT-2 2-469PORT-3 2-469PORT-4 2-470PORT-5
2-471
PREFPATH Messages 2-491PREFPATH-1 2-492PREFPATH-2
2-492PREFPATH-3 2-493PREFPATH-4 2-494PREFPATH-6 2-494
PRIVATE_VLAN Messages 2-495PRIVATE_VLAN-2 2-495PRIVATE_VLAN-3
2-496PRIVATE_VLAN-5 2-497
PROC_MGR Messages 2-497
xxiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
PROC_MGR-SLOT#-2 2-497PROC_MGR-SLOT#-3 2-500PROC_MGR-SLOT#-4
2-500PROC_MGR-SLOT#-6 2-500
PROFILER Messages 2-500PROFILER-0 2-501PROFILER-1
2-501PROFILER-2 2-501PROFILER-3 2-501PROFILER-4 2-501PROFILER-5
2-502PROFILER-6 2-502PROFILER-7 2-502
2-502
PSS Messages 2-502PSS-0 2-502PSS-1 2-503PSS-2 2-504PSS-4
2-505PSS-5 2-505
PTPLC Messages 2-506PTPLC-3 2-506
PTP Messages 2-506PTP-5 2-506PTP-6 2-507
PULSE Messages 2-508PULSE-0 2-508PULSE-1 2-508PULSE-2
2-508PULSE-3 2-508PULSE-4 2-509PULSE-5 2-509PULSE-6 2-509PULSE-7
2-509
QD Messages 2-509QD-3 2-509
QOS Messages 2-510QOS-2 2-510QOS-3 2-511QOS-4 2-512
xxiiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
QOS-6 2-513QUACK_SMC Messages 2-515
QUACK_SMC-6 2-515R2D2_USD Messages 2-515
R2D2_USD-2 2-515R2D2_USD-6 2-515
RADIUS Messages 2-516RADIUS-2 2-516RADIUS-3 2-516RADIUS-4
2-516RADIUS-5 2-516RADIUS-6 2-517
RDL Messages 2-517RDL-2 2-517RDL-3 2-518RDL-6 2-518
RES_MGR Messages 2-519RES_MGR-1 2-519RES_MGR-2 2-520RES_MGR-3
2-520RES_MGR-4 2-521RES_MGR-5 2-522RES_MGR-6 2-522
RIB Messages 2-523RIB-0 2-523RIB-1 2-523RIB-2 2-523RIB-3
2-523RIB-4 2-525RIB-5 2-525RIB-6 2-526
RLIR Messages 2-526RLIR-2 2-526RLIR-6 2-527
RM Messages 2-527RM-6 2-527RM-SLOT#-2 2-528RM-SLOT#-4 2-529
RSCN Messages 2-529RSCN-2 2-529
xxiiiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
RSCN-4 2-530RSCN-6 2-530
SABRE_APP Messages 2-530SABRE_APP-SLOT#-2 2-531
SAC_USD Messages 2-531SAC_USD-2 2-531SAC_USD-3 2-532SAC_USD-5
2-533SAC_USD-6 2-533
SAL Messages 2-534SAL-5 2-534
SANTAP Messages 2-534SANTAP-SLOT#-2 2-534SANTAP-SLOT#-4
2-541SANTAP-SLOT#-5 2-543SANTAP-SLOT#-6 2-543
SAN_EXT_TUNER Messages 2-545SAN_EXT_TUNER-3 2-545
SCHEDULER Messages 2-545SCHEDULER-2 2-546SCHEDULER-3
2-546SCHEDULER-4 2-547SCHEDULER-6 2-547
SCM Messages 2-547SCM-2 2-547
SCSI-TARGET Messages 2-547SCSI-TARGET-2 2-548SCSI-TARGET-3
2-548SCSI-TARGET-7 2-550
SDV Messages 2-550SDV-2 2-550SDV-3 2-551SDV-4 2-553SDV-6
2-553SDV-7 2-553
SECURITYD Messages 2-553SECURITYD-2 2-553SECURITYD-3
2-555SECURITYD-6 2-555
SENSOR_USD Messages 2-556
xxivCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
SENSOR_USD-2 2-556SENSOR_USD-3 2-557SENSOR_USD-5 2-558
SENSOR_MGR Messages 2-558SENSOR_MGR-2 2-558SENSOR_MGR-3
2-558SENSOR_MGR-4 2-559
SENSOR Messages 2-559SENSOR-0 2-559SENSOR-3 2-559
SESSION-MGR Messages 2-559SESSION-MGR-2 2-559SESSION-MGR-3
2-560SESSION-MGR-4 2-560
SFC Messages 2-560SFC-3 2-560
SFM Messages 2-560SFM-2 2-560SFM-6 2-561
SIM Messages 2-561SIM-2 2-561SIM-3 2-562SIM-4 2-563SIM-5
2-563
2-574
SKSD Messages 2-574SKSD-2 2-574SKSD-3 2-574SKSD-4 2-575SKSD-5
2-575SKSD-6 2-577
SKT_USD Messages 2-577SKT_USD-2 2-577SKT_USD-6 2-577
SKYLINE_APP Messages 2-577SKYLINE_APP-SLOT#-2 2-577
SME_CPP Messages 2-577SME_CPP-2 2-578SME_CPP-3 2-579SME_CPP-5
2-584
xxvCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
SME_CPP-SLOT#-2 2-588SME_CPP-SLOT#-3 2-589SME_CPP-SLOT#-4
2-593
SNMPD Messages 2-593SNMPD-1 2-593SNMPD-2 2-593SNMPD-3
2-593SNMPD-4 2-593SNMPD-5 2-594SNMPD-6 2-594SNMPD-7 2-594
SPAN Messages 2-594SPAN-2 2-594SPAN-3 2-594SPAN-5 2-595SPAN-6
2-596
SPI Messages 2-596SPI-SLOT#-2 2-596
STATSCLIENT Messages 2-596STATSCLIENT-2 2-597STATSCLIENT-3
2-597STATSCLIENT-6 2-597
STATSINFRA Messages 2-597STATSINFRA-3 2-597
STATSPROFILER Messages 2-598STATSPROFILER-2 2-598STATSPROFILER-3
2-599STATSPROFILER-4 2-600STATSPROFILER-5 2-601
STP Messages 2-611STP-2 2-612STP-3 2-619STP-4 2-620STP-6
2-621
SVC_BATTERY Messages 2-623SVC_BATTERY-SLOT#-2
2-623SVC_BATTERY-SLOT#-4 2-625SVC_BATTERY-SLOT#-6 2-625
SVC Messages 2-626SVC-0 2-626
xxviCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
SVC-1 2-626SVC-2 2-626SVC-3 2-627SVC-4 2-639SVC-5 2-648SVC-6
2-648SVC-7 2-663
SYSMGR Messages 2-663SYSMGR-2 2-664SYSMGR-3 2-687SYSMGR-4
2-696SYSMGR-5 2-698SYSMGR-6 2-703SYSMGR-7 2-705
SYSTEM HEALTH LC Messages 2-707SYSTEM HEALTH LC-2 2-707SYSTEM
HEALTH LC-4 2-708SYSTEM HEALTH LC-6 2-710
SYSTEMHEALTH Messages 2-710SYSTEMHEALTH-2 2-711SYSTEMHEALTH-4
2-714SYSTEMHEALTH-5 2-719SYSTEMHEALTH-6 2-721
TACACS Messages 2-723TACACS-2 2-723TACACS-3 2-723TACACS-4
2-723TACACS-5 2-723TACACS-6 2-724
TBIRD_CMN_USD Messages 2-724TBIRD_CMN_USD-6 2-724
TBIRD_FWD_USD Messages 2-724TBIRD_FWD_USD-6 2-724
TBIRD_MAC_USD Messages 2-725TBIRD_MAC_USD-3 2-725TBIRD_MAC_USD-6
2-725
TBIRD_QUE_USD Messages 2-725TBIRD_QUE_USD-6 2-725
TBIRD_XBAR_USD Messages 2-725TBIRD_XBAR_USD-6 2-725
xxviiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
TCAP Messages 2-726TCAP-2 2-726
TIM Messages 2-726TIM-2 2-726
TIM Messages 2-727TIM-3 2-727
TIM Messages 2-728TIM-4 2-728
TIM Messages 2-729TIM-5 2-729
TLPORT Messages 2-739TLPORT-2 2-740TLPORT-3 2-740TLPORT-4
2-741TLPORT-6 2-741
TPC Messages 2-741TPC-SLOT#-5 2-742
TTYD Messages 2-742TTYD-2 2-743TTYD-3 2-743TTYD-6 2-743
TUNNEL Messages 2-743TUNNEL-2 2-744TUNNEL-3 2-744TUNNEL-4
2-744TUNNEL-5 2-745TUNNEL-7 2-746
TUSCANY_APP Messages 2-746TUSCANY_APP-SLOT#-2 2-746
U2RIB Messages 2-746U2RIB-2 2-747U2RIB-3 2-747U2RIB-5
2-747U2RIB-6 2-748
UDLD Messages 2-748UDLD-3 2-748UDLD-4 2-749UDLD-5 2-749
UFDM Messages 2-750UFDM-2 2-750
xxviiiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
USBHSD Messages 2-750USBHSD-1 2-750USBHSD-2 2-751USBHSD-3
2-752USBHSD-5 2-752USBHSD-6 2-753USBHSD-7 2-753
USDBA Messages 2-753USDBA-2 2-754USDBA-6 2-754
VAJRA_USD Messages 2-754VAJRA_USD-6 2-754
VAL_USD Messages 2-754VAL_USD-6 2-754
VDC_MGR Messages 2-754VDC_MGR-2 2-755VDC_MGR-3 2-756VDC_MGR-5
2-756
VEC Messages 2-757VEC-SLOT#-3 2-757VEC-SLOT#-4 2-758VEC-SLOT#-5
2-758
VEDB_MGR Messages 2-761VEDB_MGR-2 2-761VEDB_MGR-6 2-761
VES Messages 2-762VES-SLOT#-4 2-762VES-SLOT#-5 2-762
VFC Messages 2-763VFC-3 2-763VFC-6 2-764
VIPER_CMN_USD Messages 2-764VIPER_CMN_USD-6 2-764
VIPER_ICB_USD Messages 2-764VIPER_ICB_USD-2 2-764VIPER_ICB_USD-6
2-764
VIPER_MAC_USD Messages 2-764VIPER_MAC_USD-6 2-765
VIPER_XBAR_USD Messages 2-765VIPER_XBAR_USD-6 2-765
xxixCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
VIP_FWD Messages 2-765VIP_FWD-6 2-765
VIP_ILK Messages 2-765VIP_ILK-6 2-765
VLAN_MGR Messages 2-766VLAN_MGR-2 2-766VLAN_MGR-3
2-766VLAN_MGR-4 2-766VLAN_MGR-5 2-766VLAN_MGR-6 2-767
VMAN Messages 2-767VMAN-2 2-768VMAN-3 2-775VMAN-4 2-775VMAN-5
2-775
VMM Messages 2-776VMM-2 2-776
VNI Messages 2-777VNI-2 2-777VNI-3 2-777VNI-6 2-777
VNTAGC Messages 2-777VNTAGC-5 2-778
VNTAG_MGR Messages 2-778VNTAG_MGR-2 2-778VNTAG_MGR-4
2-779VNTAG_MGR-5 2-779
2-779
VPC Messages 2-779VPC-2 2-780VPC-3 2-782VPC-4 2-784VPC-5
2-786VPC-6 2-789
VPM Messages 2-791VPM-2 2-791VPM-3 2-792VPM-4 2-793VPM-6
2-793VPM-SLOT#-2 2-796
xxxCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
VRRP-CFG Messages 2-796VRRP-CFG-2 2-796VRRP-CFG-3
2-796VRRP-CFG-5 2-797
VRRP-ENG Messages 2-797VRRP-ENG-2 2-797VRRP-ENG-3
2-797VRRP-ENG-4 2-799VRRP-ENG-5 2-799VRRP-ENG-6 2-800
VSAN Messages 2-800VSAN-2 2-800VSAN-3 2-800VSAN-6 2-801
VSC Messages 2-802VSC-SLOT#-2 2-802VSC-SLOT#-3 2-802VSC-SLOT#-5
2-802
VSD Messages 2-803VSD-SLOT#-2 2-803VSD-SLOT#-6 2-803
VSHA Messages 2-803VSHA-3 2-803VSHA-SLOT#-5 2-804
VSHD Messages 2-804VSHD-2 2-804VSHD-3 2-805VSHD-4 2-806VSHD-5
2-806VSHD-7 2-807
VTP Messages 2-807VTP-0 2-807VTP-1 2-807VTP-2 2-807VTP-3
2-808VTP-4 2-809VTP-5 2-810VTP-6 2-810VTP-7 2-811
WWN Messages 2-812
xxxiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
WWN-1 2-812WWN-2 2-812WWN-3 2-814WWN-4 2-815WWN-5 2-815WWN-6
2-816WWN-7 2-817
X2_USD Messages 2-817X2_USD-2 2-818
X2_USD Messages 2-818X2_USD-5 2-818
XBAR_CLIENT Messages 2-819XBAR_CLIENT-2 2-819XBAR_CLIENT-3
2-820XBAR_CLIENT-SLOT#-2 2-821XBAR_CLIENT-SLOT#-3 2-822
XBAR_DRIVER_USD Messages 2-822XBAR_DRIVER_USD-2
2-822XBAR_DRIVER_USD-3 2-823XBAR_DRIVER_USD-5
2-823XBAR_DRIVER_USD-6 2-823
XBAR Messages 2-824XBAR-2 2-824XBAR-3 2-825XBAR-4 2-825XBAR-5
2-826
XCVR_USD Messages 2-830XCVR_USD-6 2-830
XCVR Messages 2-831XCVR-6 2-831
XMLMA Messages 2-831XMLMA-2 2-831XMLMA-3 2-832XMLMA-5
2-832XMLMA-6 2-832
XMLSA Messages 2-832XMLSA-2 2-833XMLSA-5 2-833XMLSA-6 2-833
ZBM Messages 2-834
xxxiiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
ZBM-2 2-834ZBM-4 2-836ZBM-6 2-836
ZONE Messages 2-837ZONE-2 2-838ZONE-3 2-846ZONE-4 2-846ZONE-5
2-849ZONE-6 2-850
xxxiiiCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Contents
xxxivCisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Preface
This document lists and describes the system messages for Cisco
NX-OS software. The system software sends these messages to the
console (and, optionally, to a logging server on another system)
during operation. Not all messages indicate a problem with your
system. Some messages are purely informational, while others might
help diagnose problems with links, internal hardware, or the system
software.
This document includes system messages for all CiscoNX-OS
software releases.
This chapter includes the following sections:
• Audience, page 1
• Organization, page 1
• Document Conventions, page 2
• Documentation Feedback, page 2
• Obtaining Documentation and Submitting a Service Request, page
3
AudienceThis guide is for system administrators who are
responsible for managing Cisco NX-OS systems.
OrganizationThis guide is organized as follows:
Chapter Title Description
Chapter 1 Introduction to System Messages for Cisco NX-OS
Describes the structure of system messages and the format of
system log files.
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Lists the messages that may appear in log files, and indicates
suggested remedies where applicable for the Cisco MDS and Nexus
7000 Family.
-1Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Document ConventionsCommand descriptions use these
conventions:
Screen examples use these conventions:
This document uses the following conventions:
Note Means reader take note. Notes contain helpful suggestions
or references to material not covered in the manual.
Caution Means reader be careful. In this situation, you might do
something that could result in equipment damage or loss of
data.
Documentation FeedbackTo provide technical feedback on this
document, or to report an error or omission, please send your
comments to [email protected]. We appreciate your
feedback.
Convention Description
boldface font Commands and keywords are in boldface.
italic font Arguments for which you supply values are in
italics.
[ ] Elements in square brackets are optional.
[ x | y | z ] Optional alternative keywords are grouped in
brackets and separated by vertical bars.
string A nonquoted set of characters. Do not use quotation marks
around the string or the string will include the quotation
marks.
screen font Terminal sessions and information that the switch
displays are in screen font.
boldface screen font
Information that you must enter is in boldface screen font.
italic screen font Arguments for which you supply values are in
italic screen font.
< > Nonprinting characters, such as passwords, are in
angle brackets.
[ ] Default responses to system prompts are in square
brackets.
!, # An exclamation point (!) or a pound sign (#) at the
beginning of a line of code indicates a comment line.
-2Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
nexus7k-docfeedback(mailer list) nexus7k-docfeedback(mailer
list)
-
Obtaining Documentation and Submitting a Service RequestFor
information on obtaining documentation, submitting a service
request, and gathering additional information, see the monthly
What’s New in Cisco Product Documentation, which also lists all new
and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a
Really Simple Syndication (RSS) feed and set content to be
delivered directly to your desktop using a reader application. The
RSS feeds are a free service and Cisco currently supports RSS
version 2.0.
-3Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
-
-4Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02
-
Cisco MDS 9000 Family and NexOL-29318-02, Cisco MDS NX-OS
Release 6.x
C H A P T E R 1
Introduction to System Messages for Cisco NX-OS
This chapter describes system messages, as defined by the syslog
protocol (RFC 3164). It describes how to understand the syslog
message format and how to capture system messages for review.
This chapter contains the following sections:
• System Log Message Format, page 1-1
• Capturing System Messages and History, page 1-5
System Log Message FormatSystem log messages begin with a
percent sign (%) and are displayed in the following formats:
• Syslog Format On a Resident Switch, page 1-1
• Syslog Format On a Remote-Logging Server, page 1-3
Syslog Format On a Resident SwitchThe format for a resident
syslog is:
month dd hh:mm:ss switchname facility-severity-MNEMONIC
descriptionor month dd hh:mm:ss switchname
facility-SLOTnumber-severity-MNEMONIC descriptionor month dd
hh:mm:ss switchname facility-STANDBY-severity-MNEMONIC
description
For example:
Nov 1 14:07:58 excal-113 %MODULE-5-MOD_OK: Module 1 is onlineNov
1 14:07:58 excal-113 %PORT-3-IF_UNSUPPORTED_TRANSCEIVER:
Transceiver for interface fc1/13 is not supported.
Table 1-1 System Log Message Format Description
Element Description
month dd The date and month of the error or event
hh:mm:ss The time of the error or event
1-1us 7000 Series NX-OS System Messages Reference
-
Chapter 1 Introduction to System Messages for Cisco NX-OSSystem
Log Message Format
FACILITY is a code consisting of two or more uppercase letters
that indicate the facility to which the system message refers. A
facility is a hardware device, a protocol, a feature, or a module
of the system software.
System message SEVERITY codes range from 0 to 7 and reflect the
severity of the condition. The lower the number, the more serious
the situation. Table 1-2 lists the severity levels.
MNEMONIC is a code that uniquely identifies the system
message.
Message-text is a text string that describes the condition. This
portion of the message might contain detailed information about the
event, including terminal port numbers, network addresses, or
addresses that correspond to locations in the system memory address
space. Because the information in these variable fields changes
from message to message, it is represented here by short strings
enclosed in square brackets ([ ]). A decimal number, for example,
is represented as [dec].
Table 1-3 lists the representations of variable fields and the
type of information in the fields.
switchname The name of the switch
facility The facility of the error or event (daemon, kernel,
VSHD, or other facility)
severity Single-digit code from 0 to 7 that indicates the
severity of the message
MNEMONIC Text string that uniquely describes the system
message
%$VDC #%$ An optional virtual device context (VDC) ID that
appears in the description for messages requiring VDC IDs
%$VRF #%$ An optional virtual routing and forwarding (VRF) ID
that appears in the description for messages requiring VRF IDs
description Text string containing detailed information about
the event being reported
Table 1-1 System Log Message Format Description (continued)
Element Description
Table 1-2 System Message Severity Levels
Level Description
0 – emergency System unusable
1 – alert Immediate action needed
2 – critical Critical condition
3 – error Error condition
4 – warning Warning condition
5 – notification Normal but significant condition
6 – informational Informational message only
7 – debugging Appears during debugging only
Table 1-3 Representation of Variable Fields in System
Messages
Representation Type of Information
[dec] Decimal number
[hex] Hexadecimal number
1-2Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 1 Introduction to System Messages for Cisco NX-OSSystem
Log Message Format
The following example system message shows how the variable
field might be used:
%MODULE-5-MOD_MINORSWFAIL: Module [dec] reported a failure in
service [chars]
In this example,
Facility code =MODULE (indicating that it is a module-specific
error)
Severity =5 (notification)
Alarm/event code= MOD_MINORSWFAIL
Description of the problem= Module [dec] reported a failure in
service [chars]
[dec] is the module slot number associated with this
message.
[chars] is the service name that experienced this failure.
System log messages begin with a percent sign (%) and are
displayed in the following format (see Table 1-4).
Syslog Format On a Remote-Logging ServerThe syslog format on a
remote-logging server is:
month dd hh:mm:ss IP-addr-switch : year month day hh:mm:ss
Timezone: facility-severity-MNEMONIC descriptionor month dd
hh:mm:ss IP-addr-switch : year month day hh:mm:ssTimezone:
facility-SLOTnumber-severity-MNEMONIC descriptionor month dd
hh:mm:ss IP-addr-switch : year month day hh:mm:ss Timezone:
facility-STANDBY-severity-MNEMONIC description
For example:
sep 21 11:09:50 172.22.22.45 : 2005 Sep 04 18:18:22 UTC:
%AUTHPRIV-3-SYSTEM_MSG: ttyS1:togetattr: Input/output error -
getty[28224]switch resident syslog 2005 Sep 4 18:18:22 switch
%AUTHPRIV-3-SYSTEM_MSG: ttyS1:togetattr: Input/output error -
getty[28224]time on switch : 2005 Sep 4 18:18:22 time on Loggng
Server : Sep 21 11:09:50 fc1/13 is not supported.
[char] Single character
[chars] Character string
Table 1-3 Representation of Variable Fields in System
Messages
Representation Type of Information
Table 1-4 System Log Message Format Description
Element Description
month dd The date and month of the error or event
hh:mm:ss The time of the error or event
IP-addr-switch The IP address of the switch
facility The facility of the error or event (daemon, kernel,
VSHD, or other facility)
severity Single-digit code from 0 to 3 that indicates the
severity of the message
MNEMONIC Text string that uniquely describes the system
message
1-3Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 1 Introduction to System Messages for Cisco NX-OSSystem
Log Message Format
FACILITY is a code consisting of two or more uppercase letters
that indicate the facility to which the system message refers. A
facility is a hardware device, a protocol, a feature, or a module
of the system software.
System message SEVERITY codes range from 0 to 3 and reflect the
severity of the condition. The lower the number, the more serious
the situation. Table 1-5 lists the severity levels.
MNEMONIC is a code that uniquely identifies the system
message.
Message-text is a text string that describes the condition. This
portion of the message might contain detailed information about the
event, including terminal port numbers, network addresses, or
addresses that correspond to locations in the system memory address
space. Because the information in these variable fields changes
from message to message, it is represented here by short strings
enclosed in square brackets ([ ]). A decimal number, for example,
is represented as [dec].
Table 1-6 lists the representations of variable fields and the
type of information in the fields.
The following example system message shows how the variable
field might be used:
%AUTHPRIV-3-SYSTEM_MSG: AUTHPRIV [dec] reported a failure in
service [chars]
In this example,
Facility code =AUTHPRIV (indicating that it is a
authpriv-specific error)
Severity =3 (notification)
%$VDC #%$ An optional virtual device context (VDC) ID that
appears in the description for messages requiring VDC IDs
%$VRF #%$ An optional virtual routing and forwarding (VRF) ID
that appears in the description for messages requiring VRF IDs
description Text string containing detailed information about
the event being reported
Table 1-4 System Log Message Format Description (continued)
Element Description
Table 1-5 System Log Message Format description
Level Description
0 – emergency System unusable
1 – alert Immediate action needed
2 – critical Critical condition
3 – notification Normal but significant condition
Table 1-6 Representation of Variable Fields in System
Messages
Representation Type of Information
[dec] Decimal number
[hex] Hexadecimal number
[char] Single character
[chars] Character string
1-4Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 1 Introduction to System Messages for Cisco
NX-OSCapturing System Messages and History
Alarm/event code= SYSTEM_MSG
Description of the problem= Authpriv [dec] reported a failure in
service [chars]
[dec] is the module slot number associated with this
message.
[chars] is the service name that experienced this failure.
Capturing System Messages and HistoryThe system messages are
displayed instantly on the console, by default, or are redirected
to an internal log file, or a syslog server. System message
severity levels correspond to the keywords assigned by the logging
global configuration commands. These keywords define where and at
what level these messages appear (see to the Cisco NX-OS System
Management Configuration Guide). Only system messages that
correspond to the configured logging level or higher severity
messages are logged. As an example, if you set the logging level to
3 (error), then you get error, critical, alerts, and emergency
system messages, but you do not get warning, notification,
informational, or debugging system messages.
For complete information about handling system messages, see the
Cisco NX-OS System Management Configuration Guide, Release 4.1.
Saving the System Messages LogThe logging logfile global
configuration command enables copying of system messages to an
internal log file and optionally sets the size of the file. To
display the messages that are logged in the file, use the show
logging EXEC command. The first message displayed is the oldest
message in the buffer. To clear the current contents of the buffer,
use the clear debug-logfile command.
Logging System Messages to a Syslog ServerThe logging host-name
command identifies a syslog server host to receive logging
messages. The host-name argument is the name or Internet address of
the host. By issuing this command more than once, you build a list
of syslog servers that receive logging messages. The no logging
host-name command deletes the syslog server with the specified
address from the list of syslog servers.
1-5Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 1 Introduction to System Messages for Cisco
NX-OSCapturing System Messages and History
1-6Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Cisco MDS 9000 Family and NexOL-29318-02, Cisco MDS NX-OS
Release 6.x
C H A P T E R 2
System Messages and Recovery Procedures for the Cisco MDS 9000
and Nexus 7000 Family
This chapter includes system messages for the Cisco NX-OS MDS
9000 and Nexus 7000 families of switches. The messages are listed
in alphabetical order by the system facility that produces them.
Within each system facility section, messages are listed
alphabetically by severity and mnemonics. Each error message is
followed by an explanation and a recommended action.
AAA MessagesThis section contains the AAA messages.
AAA-1
Error Message AAA-1-AAA_SESSION_LIMIT_REJECT: aaa request
rejected as maximum aaa sessions are in progress
Explanation Aaa request rejected as the limit for maximum
concurrent aaa sessions is reached
Recommended Action Please contact the Cisco reseller through
which you procured the product for support. If you have purchased a
Cisco support contract please call Cisco TAC for support.
AAA-2
Error Message AAA-2-AAA_NVRAM_UPGRADE_FAILURE: upgrading of
accounting log failed. [chars]
Explanation Upgrading of accounting log failed.
Recommended Action Please contact the Cisco reseller through
which you procured the product for support. If you have purchased a
Cisco support contract please call Cisco TAC for support.
2-1us 7000 Series NX-OS System Messages Reference
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message AAA-2-AAA_PROGRAM_EXIT: aaa daemon exiting:
[chars]
Explanation Aaa daemon is exiting.
Recommended Action Please contact the Cisco reseller through
which you procured the product for support. If you have purchased a
Cisco support contract please call Cisco TAC for support.
AAA-3
Error Message AAA-3-AAA_ERR_MSG: [chars]
Explanation AAA Error Message
Recommended Action No action is required.
Error Message AAA-3-AAA_NVRAMFAILURE: nvram failure
Explanation Nvram can not be read/written to. Hence accounting
log can not be stored there
Recommended Action Please contact the Cisco reseller through
which you procured the product for support. If you have purchased a
Cisco support contract please call Cisco TAC for support.
AAA-6
Error Message AAA-6-AAA_ACCOUNTING_MESSAGE: [chars]
Explanation Accounting Message
Recommended Action No action is required.
AAA-7
Error Message AAA-7-AAA_DBG_MSG: [chars]
Explanation AAA Debug Message
Recommended Action No action is required.
AAM MessagesThis section contains the AAM messages.
2-2Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
AAM-2
Error Message AAM-2-ELS_FC2_GL_SINDEX_LOOKUP_FAILED: Failed to
lookup global port index for interface [[chars]]
Explanation Failed to lookup global port index for interface
[chars]
Recommended Action No action is required.
AAM-3
Error Message AAM-3-ALLOC_FAILED: Failed in File:[chars]
Line:[dec] for type [dec] size [dec]
Explanation AAM process could not allocate heap memory in
File:[chars], at line:[dec], for memory-type:[dec] of
Size:[dec]
Recommended Action No action is required.
Error Message AAM-3-ASSERTION_FAILED: Failed in File:[chars]
Line:[dec]
Explanation AAM Process assertion failed in File:[chars], at
line:[dec]
Recommended Action No action is required.
ACLLOG MessagesThis section contains the ACLLOG messages.
ACLLOG-4
Error Message ACLLOG-4-ACLLOG_MAXFLOW_REACHED: [chars]
Explanation Max flow reached in current interval: [chars]
Recommended Action No action is required.
Error Message ACLLOG-4-ACLLOG_THRESHOLD: [chars]
Explanation Threshold Reached for Flow: [chars]
Recommended Action No action is required.
2-3Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
ACLLOG-6
Error Message ACLLOG-6-ACLLOG_FLOW_INTERVAL: [chars]
Explanation Flow info in current alert interval: [chars]
Recommended Action No action is required.
Error Message ACLLOG-6-ACLLOG_NEW_FLOW: [chars]
Explanation New Acllog Flow: [chars]
Recommended Action No action is required.
ACLMGR MessagesThis section contains the ACLMGR messages.
ACLMGR-2
Error Message ACLMGR-2-ACLMGR_COMMIT_FAIL: Commit failed:
[chars]
Explanation The PPF commit failed
Recommended Action No action is required.
Error Message ACLMGR-2-ACLMGR_NO_ERRDISABLED: [chars] event on
interface [chars] ([hex]) allowed to succeed in spite of
access-list failure
Explanation Although an access-list operation failed during a
port event, the port event still finished successfully because
errdisable is disallowed
Recommended Action No action is required.
Error Message ACLMGR-2-EXITING: Exit reason: [chars]
Explanation The ACLMGR service process has exited due to [char].
The process has probably been restarted automatically.
Recommended Action No action is required.
Error Message ACLMGR-2-INITFAIL: ACLMGR Service Init failed:
[chars]
Explanation ACLMGR Service initialization failed. [chars]
explains the reason for the failure.
Recommended Action No action is required.
2-4Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ACLMGR-2-MALLOC_ERROR: Size [dec] bytes
Explanation The ACLMGR service could not allocate memory.
Recommended Action Please contact the Cisco reseller through
which you procured the product for support. If you have purchased a
Cisco support contract please call Cisco TAC for support.
Error Message ACLMGR-2-PSS_ERROR: [chars]: PSS ret.
val=[dec]
Explanation The ACLMGR service encountered error while operating
on a persistent storage database.
Recommended Action No action is required.
ACLMGR-3
Error Message ACLMGR-3-ACLMGR_DB_LOCK_MSG: ACL database message,
reason: [chars], session 0x%llx, type: [chars]
Explanation ACL PPF database lock acquire/release related
message.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_GSYNC_ERROR: Error occured during
global sync of ACL runtime database to standby, reason: [chars] ,
[chars]
Explanation ACL snapshot to send the copy of runtime database to
standby failed
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_PPF_ERROR: PPF error: [chars]
Explanation The PPF generated error
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_PSS_CORRUPTED: [chars] PSS found
corrupted
Explanation The ACLMGR service has detected corruption in one of
its persistent information database. The database would be
recreated.
Recommended Action No action is required.
2-5Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ACLMGR-3-ACLMGR_STAT_CONSOLIDATION_FAILURE: ACL
statistic parsing or consolidation failed
Explanation A statistic update failed during the parsing or
consolidation step; statistics may have been lost
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_VACL_REDIRECTION_DISABLED_REMOVAL:
VACL redirection to interface [chars] ([hex]) disabled: the port
has been removed
Explanation A VACL redirection to the port has been deactivated
because the port has been removed
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_VERIFY_FAIL: Verify failed:
[chars]
Explanation The PPF Verify failed
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_COMMIT_FAIL: Commit failed:
[chars]
Explanation The PPF commit failed
Recommended Action No action is required.
Error Message ACLMGR-3-MTSERROR: [chars]
Explanation ACLMGR Service encountered an MTS error. [chars]
specifies the context where the error occured.
Recommended Action No action is required.
ACLMGR-4
Error Message ACLMGR-4-ACLMGR_PPF_WARNING: PPF warning:
[chars]
Explanation The PPF generated warning
Recommended Action No action is required.
Error Message ACLMGR-4-ACLMGR_VACL_REDIRECTION_DISABLED_PCM:
VACL redirection to interface [chars] ([hex]) disabled: the port
became a portchannel member
Explanation A VACL redirection to the port has been temporarily
deactivated because it is now a member in a port channel
Recommended Action No action is required.
2-6Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ACLMGR-4-PSS_VERSION_MISMATCH: PSS [dec] Code
[dec]
Explanation There was a version mismatch between the ACLMGR
service and one of its persistent storage databases. The persistent
information has been translated to the new format.
Recommended Action No action is required.
ACLMGR-6
Error Message ACLMGR-6-ACLMGR_PPF_NOTIF: PPF notification:
[chars]
Explanation The PPF generated notification
Recommended Action No action is required.
Error Message ACLMGR-6-BECAME_ACTIVE: Became ACTIVE from standby
mode
Explanation The ACLMGR service on the standby supervisor became
active and it is ready to serve client requests.
Recommended Action No action is required.
Error Message ACLMGR-6-BECAME_STDBY: Became STANDBY from active
mode
Explanation The ACLMGR service became standby from active
mode.
Recommended Action No action is required.
Error Message ACLMGR-6-FAILED_TO_SEND_HEARTBEAT: Failed to send
heartbeat to system manager: Reason=[chars]
Explanation The ACLMGR service was unable to send heartbeat to
the system manger
Recommended Action No action is required.
Error Message ACLMGR-6-SERVICE_UP: Initialized [chars]
Explanation The ACLMGR service is up and ready The service was
initialized in [char] mode.
Recommended Action No action is required.
Error Message ACLMGR-6-SRVEXIT: ACLMGR Service shutting down
gracefully
Explanation ACLMGR Service is shutting down gracefully. This is
an informational message.
Recommended Action No action is required.
2-7Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ACLMGR-6-SWITCHOVER: Switching Over to other
Sup.
Explanation The ACLMGR service has successfully switched over to
the standby supervisor card.
Recommended Action No action is required.
ACLQOS MessagesThis section contains the ACLQOS messages.
ACLQOS-SLOT#-2
Error Message ACLQOS-SLOT#-2-ACLQOS_FAILED: ACLQOS failure:
[chars]
Explanation ACLQOS operation failed in the aclqos client
Recommended Action No DDTS.
Error Message ACLQOS-SLOT#-2-ACLQOS_INBAND_INTERFACE_FAILURE:
Inband interface lif lookup failed ([chars])
Explanation Inband interface lif lookup failed
Recommended Action No DDTS.
Error Message ACLQOS-SLOT#-2-ACLQOS_MALLOC_FAILED: Memory
allocation failed. [chars]
Explanation Memory allocation failed. This is a critical
failure
Recommended Action No DDTS.
Error Message ACLQOS-SLOT#-2-ACLQOS_OOTR: Tcam resource
exhausted: [chars]
Explanation Tcam resources to program acls exhausted
Recommended Action No DDTS.
Error Message ACLQOS-SLOT#-2-PPF_FAILED: Database failure:
[chars]
Explanation Database operation failed in the aclqos client
Recommended Action No DDTS.
2-8Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
ACLQOS-SLOT#-3
Error Message ACLQOS-SLOT#-3-ACLQOS_CC_INVALID: Invalid
Congestion Control parameters: [chars]
Explanation Invalid Congestion Control parameters
Recommended Action No DDTS.
Error Message ACLQOS-SLOT#-3-ACLQOS_MCM_ERROR: MCM Message
Inconsistent. Please collect MCM and ACLMgr Tech Support for all
VDCs
Explanation MCM Message Inconsistent
Recommended Action No DDTS.
Error Message ACLQOS-SLOT#-3-ACLQOS_PAUSE_INVALID: Invalid Pause
parameters: [chars]
Explanation Invalid Pause parameters
Recommended Action No DDTS.
Error Message ACLQOS-SLOT#-3-ACLQOS_QUEUING_ERROR: ACL/QoS
queuing error: [chars]
Explanation Internal error in ACL/QoS queuing config
Recommended Action No DDTS.
ACLQOS-SLOT#-4
Error Message ACLQOS-SLOT#-4-ACLQOS_ATOMIC_ERR: [chars]
Explanation Tcam will be overused, please turn off atomic
update
Recommended Action No DDTS.
Error Message ACLQOS-SLOT#-4-ACLQOS_BC_OVER_THRESHOLD: Bank
Chaining enabled: Inst [dec]susagehasreacheditsthreshold'
Explanation Tcam is almost full
Recommended Action No DDTS.
2-9Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ACLQOS-SLOT#-4-ACLQOS_FC_WARNING: Found stale FCoE
entry in instance [dec]. VSAN: [dec], SID: [hex], DID: [hex],
SI:[dec], SI_MASK:[dec], RW_VSAN: [dec], RW_VSAN_FLAG: [dec],
RW_SID: [hex], RW_SID_FLAG: [dec], RW_DID: [hex]. RW_DID_FLAG:
[dec] Cleaning it up.
Explanation Found stale FCoE entry in instance [dec]. VSAN:
[dec], SID: 0x[hex], DID: 0x[hex], SI:[dec], SI_MASK:[dec],
RW_VSAN:[dec], RW_VSAN_FLAG: [dec], RW_SID: 0x[hex],
RW_SID_FLAG:[dec], RW_DID: 0x[hex]. RW_DID_FLAG: [dec] Cleaning it
up.
Recommended Action No DDTS.
Error Message ACLQOS-SLOT#-4-ACLQOS_MATCH_ALL_MERGE_UPDATE:
Warning (match_all merging): [chars]
Explanation Warning (match_all merging)
Recommended Action No DDTS.
Error Message ACLQOS-SLOT#-4-ACLQOS_OVER_THRESHOLD: Inst [dec]
Tcam [dec] Bank [dec]susagehasreacheditsthreshold'
Explanation Tcam is almost full
Recommended Action No DDTS.
Error Message ACLQOS-SLOT#-4-ACLQOS_QUEUING_COS2Q_INVALID:
ACL/QoS invalid queuing policy because of cos map change: [chars]
queue [chars], interface [chars]
Explanation Attemped to configure an invalid queuing policy
Recommended Action No DDTS.
Error Message ACLQOS-SLOT#-4-ACLQOS_QUEUING_INVALID: ACL/QoS
invalid queuing policy: [chars]
Explanation Attemped to configure an invalid queuing policy
Recommended Action No DDTS.
Error Message ACLQOS-SLOT#-4-ACLQOS_UNDER_THRESHOLD: Tcam [dec]
Bank [dec]'s usage is below the threshold now
Explanation Tcam's usage is below the threshold
Recommended Action No DDTS.
2-10Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ACLQOS-SLOT#-4-ACLQOS_WARNING: ACLQOS Warning:
[chars]
Explanation ACLQOS Warnings
Recommended Action No DDTS.
ACLQOS-SLOT#-5
Error Message ACLQOS-SLOT#-5-ACLQOS_DISRUPTIVE_IPv6_UPDATE:
Disruptive update of IPv6 compression entries
Explanation Disruptive IPv6 compression entries update
Recommended Action No DDTS.
Error Message ACLQOS-SLOT#-5-ACLQOS_NON_ATOMIC: Non atomic
ACL/QoS policy update done for [chars]
Explanation Non atomic ACL/QoS policy update was done
Recommended Action No DDTS.
ACLTCAM MessagesThis section contains the ACLTCAM messages.
ACLTCAM-2
Error Message ACLTCAM-2-ACL_TCAM_ADJ_EXHAUSTED: ACLTCAM failed
to program route for VSAN: [dec], SID: [chars] DID: [chars], error:
[chars].
Explanation ACLTCAM process experienced a failure while
programming route for VSAN [dec] SID [chars] DID [chars] due to
resource exhaustion. [chars] is the error code.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_ALMOST_FULL: TCAM close to
FULL. [chars] TCAM Usage ([dec]/[dec]) exceeded [dec]% fwd-eng:
[dec], [chars]
Explanation [chars] TCAM usage [dec]/[dec] exceeded [dec]
percent on fwd-engine [dec], [chars]
Recommended Action No action is required.
2-11Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ACLTCAM-2-ACL_TCAM_CONFIG_READ_FROM_DRIVER_FAILED:
[chars] [dec], Error: [hex].
Explanation Unable to read configuration from forwarding engine
ASIC driver. [chars] [dec], Error: 0x[hex].
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_CONFIG_WRITE_TO_DRIVER_FAILED:
[chars] [dec], Error: [hex].
Explanation Unable to write configuration to forwarding engine
ASIC driver. [chars] [dec], Error: 0x[hex].
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_FLOW_STATS_READ_FAILED:
Hardware flow stats read failed(ASIC: [dec], [chars] TCAM, Address:
[dec], Num Entries: [dec], Error: [chars]).
Explanation Hardware flow stats read failed(ASIC: [dec], [chars]
TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_INCONSISTENT_DATABASE: Database
found inconsistent.
Explanation Database found inconsistent.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_INCONSISTENT_TCAM_CONTENTS:
TCAM contents found inconsistent.
Explanation TCAM contents are found inconsistent.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_INIT_FAILED: Initialization
failed for forwarding engine ASIC: [dec], [chars] TCAM.
Explanation Initialization failed for forwarding engine ASIC
[dec], in [chars] TCAM.
Recommended Action No action is required.
2-12Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ACLTCAM-2-ACL_TCAM_INIT_REGIONS_FAILED:
Initialization failed for forwarding engine ASIC: [dec], [chars]
TCAM, [chars] Region.
Explanation Initialization of regions failed for forwarding
engine ASIC [dec], in [chars] TCAM, for [chars] Region.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_MALLOC_FAILURE: Memory
allocation failed for size [dec].
Explanation Memory allocation is failed for size [dec]
bytes.
Recommended Action Restart the process.
Error Message ACLTCAM-2-ACL_TCAM_MTS_FAILURE: MTS operation
failed: [chars].
Explanation MTS operation failed. [chars] is the reason.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_MTS_Q_FULL: MTS queue for SAP
[dec] is full
Explanation MTS queue for SAP [dec] is full
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_MTS_REGISTRATION_FAILED: MTS
registration failed for opCode: [dec].
Explanation MTS registration failed for opCode: [dec].
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_NO_ROUTE: ACLTCAM failed to get
route for VSAN: [dec], Rewrite: [chars] DID: [chars] DID MASK:
[chars], error: [hex].
Explanation ACLTCAM process experienced a failure while getting
route for VSAN [dec] Rewrite [chars] DID [chars] DID Mask [chars].
[hex] is the error code.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_NO_TCAM_LEFT: ACLTCAM resource
exhausted for interface : [chars]
Explanation ACLTCAM hardware resource is completely used.
Recommended Action No action is required.
2-13Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ACLTCAM-2-ACL_TCAM_PHY_TCAM_READ_FAILED: [chars]
read from hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address:
[dec], Num Entries: [dec], Error: [chars]).
Explanation [chars] read from hardware TCAM failed(ASIC: [dec],
[chars] TCAM, Address: [dec], Num Entries: [dec] Error:
[chars]).
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_PHY_TCAM_READ_INVALID:
Invalid([chars], value: [dec]) TCAM entry read from hardware TCAM
(FWD-Engine: [dec], [chars] TCAM, Address: [dec]), Ignoring this
entry.
Explanation Invalid([chars], value: [dec]) TCAM entry from
hardware TCAM(FWD-Engine: [dec], [chars] TCAM, Address: [dec])
Ignoring this entry
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_PHY_TCAM_WRITE_FAILED: [chars]
write to hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address:
[dec], Num Entries: [dec], Error: [chars]).
Explanation [chars] write to hardware TCAM failed(ASIC: [dec],
[chars] TCAM, Address: [dec], Num Entries: [dec] Error:
[chars]).
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_PSS_FAILURE: Failed to do PSS
operation: [chars], reason: [hex].
Explanation Failed to do PSS operation [chars]. [hex] is the
reason.
Recommended Action No action is required.
Error Message ACLTCAM-2-PSS_OPEN_FAILED: PSS open failed -
[hex].
Explanation Persistent database handle could not obtained for
ACLTCAM. [hex] is the error.
Recommended Action No action is required.
Error Message ACLTCAM-2-RECONS_FAILED: Reconstruction of TCAM
contents failed during upgrade - [hex].
Explanation During non-disruptive upgrade, the ACLTCAM contents
are not properly reconstructed. [hex] is the error.
Recommended Action No action is required.
2-14Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
ACLTCAM-3
Error Message ACLTCAM-3-ACL_TCAM_INV_TCAM_SYNC_ATTEMPT: Attempt
to write invalid shadow entry: [dec] ([dec]/[dec]) to TCAM,
fwd-engine: [dec] ([chars]), change-array: [dec]/[dec],
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ACLTCAM-3-PSSERROR: [chars]
Explanation TL Port Manager encountered a PSS error. [chars]
specifies the context where the failure occured.
Recommended Action No action is required.
Error Message ACLTCAM-3-REGISTER_FAILED: Could not register to
MTS opcode [chars] - error [hex].
Explanation ACLTCAM process could not register to the
notifications mentioned by [chars]. [hex] is the error.
Recommended Action No action is required.
ACLTCAM-4
Error Message ACLTCAM-4-ACL_TCAM_BELOW_THRESHOLD: [chars] TCAM
usage ([dec]/[dec]) fell below [dec]% fwd-eng: [dec], [chars]
Explanation [chars] TCAM usage [dec]/[dec] fell below [dec]
percent on fwd-engine [dec], [chars]
Recommended Action No action is required.
Error Message ACLTCAM-4-ACL_TCAM_BEYOND_THRESHOLD: [chars] TCAM
usage ([dec]/[dec]) exceeded [dec]% fwd-eng: [dec], [chars]
Explanation [chars] TCAM usage [dec]/[dec] exceeded [dec]
percent on fwd-engine [dec], [chars]
Recommended Action No action is required.
Error Message ACLTCAM-4-ACL_TCAM_FLOW_COUNTER_INVALIDATED: Flow
counter for flow: vsan: [dec], sid: [hex], did: [hex] with
statistics: frames = %llu & bytes = %llu was invalidated due
to: [chars]
Explanation ACLTCAM process invalidated the flow counter for
flow VSAN [dec] SID [hex] DID [hex] with collected stats of [dec]
frames and [dev] bytes was invalidated because of reason
[[chars]].
Recommended Action No action is required.
Error Message ACLTCAM-4-ACL_TCAM_FLOW_COUNTER_VALIDATED: Flow
counter for flow: vsan: [dec], sid: [hex], did: [hex] is now
valid
Explanation ACLTCAM process validated the flow counter for flow
VSAN [dec] SID [hex] DID [hex].
Recommended Action No action is required.
2-16Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ACLTCAM-4-ACL_TCAM_MTS_Q_HIGH: MTS queue for SAP
[dec] is close to full
Explanation MTS queue for SAP [dec] is close to full
Recommended Action No action is required.
Error Message ACLTCAM-4-TLPM_ALPA_CACHE_FULL: Translation Port
ALPA cache is full. Some new entries may not be cached
Explanation TL Port cache is currently fully populated with
active entries. Hence, there is no available cache space to be
assigned any newly created alpa entry on a TL Port. This is an
informational message.
Recommended Action No action is required.
ACLTCAM-6
Error Message ACLTCAM-6-ACL_TCAM_STATUS: Status: [chars].
Explanation ACLTCAM status is reported as: [chars].
Recommended Action No action is required.
Error Message ACLTCAM-6-MGRCREATED: Translation Port Manager
created.
Explanation TL Port Manager was created successfully and is up
and running. This is an informational message.
Recommended Action No action is required.
Error Message ACLTCAM-6-MGREXIT: Translation Port Manager
shutting down gracefully.
Explanation TL Port Manager is shutting down gracefully. This is
an informational message.
Recommended Action No action is required.
Error Message ACLTCAM-6-PORTDOWN: Translation Port [chars]
DOWN.
Explanation A port configured as TL Port is DOWN and out of
operation. [chars] is the interface-id string that identifies the
TL Port. This is an informational message.
Recommended Action No action is required.
Error Message ACLTCAM-6-PORTUP: Translation Port [chars] UP.
Explanation A port configured as TL Port is UP and operational.
[chars] is the interface-id string that identifies the TL Port.
This is an informational message.
Recommended Action No action is required.
2-17Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
ACL MessagesThis section contains the ACL messages.
ACL-2
Error Message ACL-2-ACL_HA_FAILURE: Failed to do high
availability operation: [chars].
Explanation Failed to do high availability operation. [chars] is
the reason.
Recommended Action No action is required.
Error Message ACL-2-ACL_INIT_FAILED: Initialization failed for
ACL: [chars], reason: [hex].
Explanation Initialization failed for ACL due to [chars],
reason: [hex].
Recommended Action No action is required.
Error Message ACL-2-ACL_LINECARD_STATUS: Status from linecard:
[dec], for module: [chars](ID: [dec]), status : [dec], error_id:
[hex], catastrophic: [chars], restart count: [dec].
Explanation Status from linecard: [dec], for module: [chars](ID:
[dec]), status : [dec], error_id: [hex], catastrophic: [chars],
restart count: [dec].
Recommended Action No action is required.
Error Message ACL-2-ACL_MTS_FAILURE: Failed to do MTS operation:
[chars].
Explanation Failed to do MTS operation. [chars] is the
reason.
Recommended Action No action is required.
Error Message ACL-2-ACL_MTS_Q_FULL: MTS queue for SAP [dec] is
full
Explanation MTS queue for SAP [dec] is full
Recommended Action No action is required.
Error Message ACL-2-ACL_MTS_REGISTRATION_FAILED: MTS options
setting to [hex] failed for opCode: [dec].
Explanation MTS options setting to [hex] failed for opCode:
[dec].
Recommended Action No action is required.
2-18Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ACL-2-ACL_PENDING_MSG_ARR_FULL: ACL Upgrade
Pending Messages Array is Full with [dec] messages. Failing the MTS
message with Opc: [dec], RR_TOKEN: [hex]
Explanation ACL Upgrade Pending Messages Array is Full with
[dec] messages. Failing the MTS message with Opc: [dec], RR_TOKEN:
[hex]
Recommended Action No action is required.
Error Message ACL-2-ACL_PSS_FAILURE: Failed to do PSS operation:
[chars], reason: [hex].
Explanation Failed to do PSS operation [chars]. [hex] is the
reason.
Recommended Action No action is required.
Error Message ACL-2-ACL_PSS_VER_FAIL: PSS file [chars] has
version [dec].[dec].[dec], expected version [dec].[dec].[dec].
Explanation There was a mismatch in the PSS version. [chars]
indicates the PSS service, [dec].[dec].[dec] its current version
number and [dec].[dec].[dec] the expected version.
Recommended Action No action is required.
Error Message ACL-2-ACL_RUNTIME_FAILURE: [chars] [dec], Error:
[hex]
Explanation ACL runtime failure is reported as [chars] [dec],
reason: [hex].
Recommended Action No action is required.
Error Message ACL-2-ACL_TCAM_FAILURE: Failed to do TCAM
operation: [chars].
Explanation Failed to do TCAM operation. [chars] is the
reason.
Recommended Action No action is required.
ACL-3
Error Message ACL-3-ACL_MTS_Q_LEAK: Possible MTS buffer leak for
SAP [dec]
Explanation Possible MTS buffer leak for SAP [dec]
Recommended Action No action is required.
2-19Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
ACL-4
Error Message ACL-4-ACL_MTS_Q_HIGH: MTS queue for SAP [dec] is
close to full
Explanation MTS queue for SAP [dec] is close to full
Recommended Action No action is required.
Error Message ACL-4-ACL_WARNING: [chars] [dec]
Explanation ACL warning messages is reported as [chars]
[dec].
Recommended Action No action is required.
ACL-5
Error Message ACL-5-ACL_ADJ_SHARING_STATUS: Successfully
completed [chars] on Generation 2 linecards.
Explanation Successfully completed the command \[chars]\ on
Generation 2 linecards.
Recommended Action No action is required.
ACL-6
Error Message ACL-6-ACL_DIAG_EVENT_STATUS: [chars] [hex].
Explanation ACL system health management event status is
reported as [chars] [hex].
Recommended Action No action is required.
Error Message ACL-6-ACL_E_PORT_EVENT_STATUS: [chars]
[chars].
Explanation ACL xEport event status is reported as [chars]
[chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_FCC_EVENT_STATUS: [chars] [chars].
Explanation ACL FCC event status is reported as [chars]
[chars].
Recommended Action No action is required.
2-20Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ACL-6-ACL_LINECARD_EVENT_STATUS: [chars]
[hex].
Explanation ACL linecard event status is reported as [chars]
[dec].
Recommended Action No action is required.
Error Message ACL-6-ACL_MCAST_EVENT_STATUS: [chars] [chars].
Explanation ACL multicast event status is reported as [chars]
[chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_NX_PORT_EVENT_STATUS: [chars]
[chars].
Explanation ACL Nx Port event status is reported as [chars]
[chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_PORT_MODE_EVENT_STATUS: [chars]
[chars].
Explanation ACL portmode event status is reported as [chars]
[chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_RUNTIME_STATUS: [chars] [dec]
Explanation ACL runtime status is reported as [chars] [dec].
Recommended Action No action is required.
Error Message ACL-6-ACL_SPAN_DEST_CONFIG_STATUS: [chars]
[chars].
Explanation ACL SPAN destination config event status is reported
as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_SPAN_SRC_CONFIG_STATUS: [chars]
[chars].
Explanation ACL SPAN source config event status is reported as
[chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_STATUS: ACL Status: [chars].
Explanation ACL status is reported as [chars].
Recommended Action No action is required.
2-21Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ACL-6-ACL_UPDATE_SSRAM_QOS_EVENT_STATUS: [chars]
[chars].
Explanation ACL update SSRAM for QoS event status is reported as
[chars] [chars].
Recommended Action No action is required.
AGNI-DPP MessagesThis section contains the AGNI-DPP
messages.
AGNI-DPP-2
Error Message AGNI-DPP-2-AGNI_DPP_PRINT_2HEX: [chars] [hex]
[hex]
Explanation Print a string and 1 value
Recommended Action No action is required.
Error Message AGNI-DPP-2-AGNI_DPP_PRINT_HEX: [chars] [hex]
Explanation Print a string and 1 value
Recommended Action No action is required.
Error Message AGNI-DPP-2-AGNI_DPP_PRINT_INT: [chars] [dec]
Explanation Print a string and 1 value
Recommended Action No action is required.
Error Message AGNI-DPP-2-AGNI_DPP_PRINT_STR: [chars] [chars]
Explanation Print a string and 1 value
Recommended Action No action is required.
Error Message AGNI-DPP-2-AGNI_DPP_PRINT: [chars]
Explanation Print a string
Recommended Action No action is required.
2-22Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
AGNI-DPP-6
Error Message AGNI-DPP-6-AGNI_DPP_DEBUG_MSG: [chars]
Explanation Debug log message
Recommended Action No action is required.
AGNIL2F MessagesThis section contains the AGNIL2F messages.
AGNIL2F-6
Error Message AGNIL2F-6-AGNIL2F_DEBUG_MSG: [chars]
Explanation Debug log message
Recommended Action No action is required.
ALI_LC MessagesThis section contains the ALI_LC messages.
ALI_LC-2
Error Message ALI_LC-2-INIT_FAIL: [chars]
Explanation Initialization failed
Recommended Action No action is required.
Error Message ALI_LC-2-INTERNAL_PORT_FAILURE: Internal port
[dec] reinit failed due to [chars]
Explanation An Internal port number [dec] on the board has
failed due to reason [chars]. The corresponding ethernet port may
become unusable
Recommended Action Please contact the Cisco reseller through
which you procured the product for support. If you have purchased a
Cisco support contract please call Cisco TAC for support.
2-23Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message ALI_LC-2-INTERNAL_PORT_REINIT: Internal port [dec]
has been reinitialized due to [chars]
Explanation An Internal port number [dec] on the board was
reinitialized due to reason [chars]. The corresponding ethernet
port may experience some packet drops
Recommended Action No action is required.
Error Message ALI_LC-2-MTS_FAILURE: [chars]
Explanation MTS send/receive failed
Recommended Action No action is required.
AMM MessagesThis section contains the AMM messages.
AMM-SLOT#-0
Error Message AMM-SLOT#-0-CLI_INIT_FAILED: CLI library
initialization failed!
Explanation AMM failed to initialize CLI
infrastructure\sbackendlibrary.Thisisafatalerror.'
Recommended Action No action is required.
Error Message AMM-SLOT#-0-TIMER_INIT_FAILED: Timer subsystem
initialization failed!
Explanation AMM failed to initialize timer library. This is a
fatal error.
Recommended Action No action is required.
AMM-SLOT#-2
Error Message AMM-SLOT#-2-AMM_MEM_ALLOC: Memory allocation
failed. [chars]
Explanation Memory allocation failed. This is a critical
failure
Recommended Action No action is required.
Error Message AMM-SLOT#-2-AMM_RECOVERY_ERROR: Error in Recovery:
[chars]
Explanation AMM failed to recover after a re-start. This is a
fatal error.
Recommended Action No action is required.
2-24Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
AMM-SLOT#-6
Error Message AMM-SLOT#-6-INITIALIZED: Internal state created
[chars]
Explanation AMM has created its internal state
stateless/stateful [chars].
Recommended Action No action is required.
APP EMULATOR MessagesThis section contains the APP EMULATOR
messages.
APP EMULATOR-SLOT#-5
Error Message APP EMULATOR-SLOT#-5-LOG_ERR_EMULATOR_DPP_DEAD:
VSAN :[dec] VT pWWN :[chars] DPP died
Explanation The DPP associated with the Virtual Target has
crashed
Recommended Action No action is required.
Error Message APP
EMULATOR-SLOT#-5-LOG_ERR_EMULATOR_VT_ACT_FAILED: VSAN :[dec] VT
pWWN :[chars] VT Activate failed
Explanation The activate step for a Virtual Target has
failed
Recommended Action No action is required.
Error Message APP
EMULATOR-SLOT#-5-LOG_ERR_EMULATOR_VT_CREATE_FAIL: VSAN :[dec] VT
pWWN :[chars] VT and NPort creation FAILED !!!
Explanation The Virtual Target and nport creation failed
Recommended Action No action is required.
Error Message APP
EMULATOR-SLOT#-5-LOG_ERR_EMULATOR_VT_DESTROYED: VSAN :[dec] Virtual
Target : [chars] Deleted
Explanation The Virtual Target in the associated VSAN is being
destroyed
Recommended Action No action is required.
2-25Cisco MDS 9000 Family and Nexus 7000 Series NX-OS System
Messages Reference
OL-29318-02, Cisco MDS NX-OS Release 6.x
-
Chapter 2 System Messages and Recovery Procedures for the Cisco
MDS 9000 and Nexus 7000 Family
Error Message APP
EMULATOR-SLOT#-5-LOG_ERR_EMULATOR_VT_VSAN_DOWN: VSAN :[dec] VT pWWN
:[chars] VSAN down
Explanation The VSAN where the Virtual Target is configured is
down
Recommended Action No action is required.
ARBITER MessagesThis section contains the ARBITER messages.
ARBITER-2
Error Message ARBITER-2-CATASTROPHIC_FAILURE: Arbiter
Catastrophic interrupt:[chars]
Explanation Arbiter trigerred Catastrophic error interrupt
Recommended Action Please contact your support
representative
Error Message ARBITER-2-MBIST_FAIL: Arbiter MBIST
failed:[chars]
Explanation Arbiter failed built in self test
Recommended Action Please contact your support
representative
ASCII-CFG MessagesThis section contains the ASCII-CFG
messages.
ASCII-CFG-2
Error Message ASCII-CFG-2-ACFG_CONFIGURATION_APPLY_ERROR: Error
encountered while Ascii configuration was being applied. Please