-
Cisco ASR 5000 Series SNMP MIB Reference Version 11.0
Last updated January 14, 2011
Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive
San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000
800 553-NETS (6387) Fax: 408 527-0883
Text Part Number: OL-23912-02
http://www.cisco.com/�
-
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN
THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE
ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION
OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING
PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU
ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A
devices: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio-frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference, in which case users will be required to correct the
interference at their own expense.
The following information is for FCC compliance of Class B
devices: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If the equipment
causes interference to radio or television reception, which can be
determined by turning the equipment off and on, users are
encouraged to try to correct the interference by using one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
Modifications to this product not authorized by Cisco could void
the FCC approval and negate your authority to operate the
product.
The Cisco implementation of TCP header compression is an
adaptation of a program developed by the University of California,
Berkeley (UCB) as part of UCB’s public domain version of the UNIX
operating system. All rights reserved. Copyright © 1981, Regents of
the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES
AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL
FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION,
THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR
TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY
INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING
OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR
ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc.
and/or its affiliates in the U.S. and other countries. A listing of
Cisco's trademarks can be found at www.cisco.com/go/trademarks.
Third party trademarks mentioned are the property of their
respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company.
Any Internet Protocol (IP) addresses and phone numbers used in
this document are not intended to be actual addresses and phone
numbers. Any examples, command display output, network topology
diagrams, and other figures included in the document are shown for
illustrative purposes only. Any use of actual IP addresses or phone
numbers in illustrative content is unintentional and
coincidental.
Cisco ASR 5000 Series SNMP MIB Reference
© 2011 Cisco Systems, Inc. and/or its affiliated entities. All
rights reserved.
-
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 iii
CONTENTS
About this Guide
.................................................................................................
v Conventions Used
....................................................................................................................................................
vi Contacting Customer Support
...............................................................................................................................
viii
Starent Chassis MIB
...........................................................................................
9 MIB Textual Conventions
......................................................................................................................................
11
Starent Chassis Traps
....................................................................................
397 Traps
.....................................................................................................................................................................
398 Standards-based Traps
..........................................................................................................................................
606
Starent MIB Conformances(3)
.......................................................................
607
starentMIB(8164).starentMIBObjects(1).starentEMSMIB(1000).starEmsMIBConformances(3)
...................... 608
Web Element Manager MIB
............................................................................
647 MIB Textual Conventions
....................................................................................................................................
648
Content Filtering Application MIB
.................................................................
713 MIB Textual Conventions
....................................................................................................................................
714
ESS Application MIB
.......................................................................................
735 MIB Textual Conventions
....................................................................................................................................
736
IPMS Application MIB
.....................................................................................
749 MIB Textual Conventions
....................................................................................................................................
750
MUR Application MIB
......................................................................................
763 MIB Textual Conventions
....................................................................................................................................
764
Default Trap Severities
...................................................................................
773 Core Platforms Default Trap Severities
................................................................................................................
774 Web Element Manager Default Trap Severities
...................................................................................................
801 Content Filtering Default Trap Severities
............................................................................................................
805 ESS Default Trap Severities
.................................................................................................................................
807 IPMS Default Trap Severities
..............................................................................................................................
808
-
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 v
About this Guide
This document pertains to features and functionality that run on
and/or that are related to the Cisco® ASR 5000 Chassis, formerly
the Starent Networks ST40.
-
About this Guide ▀ Conventions Used
▄ Cisco ASR 5000 Series SNMP MIB Reference
vi OL-23912-02
Conventions Used The following tables describe the conventions
used throughout this documentation.
Icon Notice Type Description
Information Note Provides information about important features
or instructions.
Caution Alerts you of potential damage to a program, device, or
system.
Warning Alerts you of potential personal injury or fatality. May
also alert you of potential electrical hazards.
Electro-Static Discharge (ESD)
Alerts you to take proper grounding precautions before handling
a product.
Typeface Conventions Description
Text represented as a screen display
This typeface represents displays that appear on your terminal
screen, for example: Login:
Text represented as commands This typeface represents commands
that you enter, for example: show ip access-list This document
always gives the full form of a command in lowercase letters.
Commands are not case sensitive.
Text represented as a command variable
This typeface represents a variable that is part of a command,
for example: show card slot_number slot_number is a variable
representing the desired chassis slot number.
Text represented as menu or sub-menu names
This typeface represents menus and sub-menus that you access
within a software application, for example: Click the File menu,
then click New
Command Syntax Conventions
Description
{ keyword or variable }
Required keywords and variables are surrounded by grouped
brackets. Required keywords and variables are those components that
are required to be entered as part of the command syntax.
-
About this Guide Conventions Used ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 vii
Command Syntax Conventions
Description
[ keyword or variable ]
Optional keywords or variables, or those that a user may or may
not choose to use, are surrounded by square brackets.
| With some commands there may be a group of variables from
which the user chooses one. These are called alternative variables
and are documented by separating each variable with a vertical bar
(also known as a pipe filter). Pipe filters can be used in
conjunction with required or optional keywords or variables. For
example: { nonce | timestamp } OR [ count number_of_packets | size
number_of_bytes ]
-
About this Guide ▀ Contacting Customer Support
▄ Cisco ASR 5000 Series SNMP MIB Reference
viii OL-23912-02
Contacting Customer Support Use the information in this section
to contact customer support.
For New Customers: Refer to the support area of
http://www.cisco.com for up-to-date product documentation or to
submit a service request. A valid username and password is required
to this site. Please contact your local sales or service
representative for additional information.
For Existing Customers with support contracts through Starent
Networks: Refer to the support area of
https://support.starentnetworks.com/ for up-to-date product
documentation or to submit a service request. A valid username and
password is required to this site. Please contact your local sales
or service representative for additional information.
Important: For warranty and repair information, please be sure
to include the Return Material Authorization (RMA) tracking number
on the outside of the package.
-
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 9
Chapter 1 Starent Chassis MIB
The following figure displays the hierarchical structure of the
management information base (MIB) for the core platform
-
Starent Chassis MIB ▀ Contacting Customer Support
▄ Cisco ASR 5000 Series SNMP MIB Reference
10 OL-23912-02
iso.org.dod.internet.private.enterprise(1.3.6.1.4.1)
starentMIB(8164)
starentMIBObjects(1)
starentTraps(2)
starentMIBConformance(3)
starentMIBGroups(1)
starentMIBCompliances(2)
starentChassis(1)
starentSlots(2)
starentSlotMapping(3)
starentFans(4)
starSlotTable(1)
starSlotMappingTable(1)
starFanTable(1)
starentLogs(5)
starLogTable(1)
starentAlertMan(8)
starentFeedback(1)
starentPolledLog(2)
starentPower(9)
starPowerTable(1)
starentCPU(10)
starCPUTable(1)
starentNPUMgr(11)
starNPUMgrTable(1)
starentSessInP(12)
starentSessMgr(13)
starentAAAMgr(14)
starentA11Mgr(15)
starentHAMgr(16)
starentFAMgr(17)
starentServiceMgr(18)
starServiceTable(1)
starentCLIMgr(19)
starCLITable(1)
starentTaskMgr(20)
starTaskTable(1)
starentPPP(21)
starentPPPStatTable(1)
starentMIPHA(22)
starMIPHAStatTable(1)
starentMIPFA(23)
starMIPFAStatTable(1)
starentRP(24)
starRPStatTable(1)
starentSubscriber(26)
starSubTable(1)
starentEISServer(27)
starEISServerTable(1)
starentThresholds(28)
starentPort(29)
starPortTable(1)
starentIPPool(30)
starIPPoolTable(1)
starentTrapData(31)
starentGGSNService(32)
starGGSNSerTable(1)
starentL2TP(33)
starL2TPTable(1)
starSessSub1(34)
starentNwReachServer(35)
starNwReachTable(1)
starentIPSEC(36)
starentSIPRoute(37)
starSIPRouteTable(1)
starentRPServiceOption(38)
starRPServiceOptionTable(1)
starentCFStats(39)
starPCFStatTable(1)
starentSIPRouteServer(40)
starSIPRouteServerTable(1)
starVIMService(41)
starVIMServiceTable(1)
starentGSS(42)
starentPDIFSys(43)
starentPDIFService(44)
StarentSGSNService(45)
starSGSNTable(1)
starentSS7Rd(46)
starentSccpNw(47)
starPDIFTable(1)
starentSGTPService(48)
starSGTPTable(1)
starentSDH(54)
starSDHTable(1)
starentE1Trib(56)
starE1TribTable(1)
starentFractE1Trib(58)
starFractE1TribTable(1)
starentCSCFPeerServer(53)
starCSCFPeerServerTable(1)
starentIPMSServer(49)
starIPMSServerTable(1)
starentCert(50)
starCertTable(1)
starentFile(51)
starFileTable(1)
starentFTPServ(52)
starFTPServTable(1)
starentSDHPath(55)
starSDHPathTable(1)
starentGPRSLink(57)
starGPRSLinkTable(1)
starentStorage(59)
starStorageTable(1)
starSccpNwTable(1)
starSS7RdTable(1)
starentFNGsys(60)
starFNGService(61)
starentPDGSys(62)
starentPDGService(63)
starIPPoolGroup(64)
starHNBGWService(65)
starFNGTable(1)
starPDGTable(1)
starIPPoolGroupTable(1)
starHNBGWServTable(1)
starentALCAPService(66)
starALCAPServTable(66)
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 11
MIB Textual Conventions The following are the supported MIB
Objects and Notifications. Not all entries are supported on all
platforms. Some may return a different output than expected.
Object
StarentSlotType
Object ID N/A
Syntax
Describes the type of a slot. Each slot in the chassis is build
to contain specific type(s) of cards. Only a card of one of the
appropriate types can be put into a specific slot.
Enumeration
unknown(1) pactac(2) spc(3) lc(4) rcc(5) spio(6)
Object StarentCardType
Object ID N/A
Description
Describes the type of a card. Each type represents a physically
different card which would have a unique part number.
Syntax Integer
Enumeration
none(1) unknown(2) spc(3) pac(4) spio(5) rcc(6) lceth(7)
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
12 OL-23912-02
lcgeth(8) lcds3 tac(10) Icoc3(11) Icoc12(12) smc(13) psc(14)
lcqgeth(15) lctgeth(16) vmc(17) vpc(18) vlceth1p(19)
Object StarentVersionNum
Object ID N/A
Description
Contains the system version identification string. Syntax
Octet String (0.. 256)
Object StarRelayState
Object ID
N/A Description
The state of a Central Office (CO) relay. Syntax
Integer Enumeration
off(1) on(2) unknown(3)
Object StarLongDurTimeoutAction
Object ID
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 13
N/A Description
The action taken by the system upon detection of a long-duration
session. Syntax
INTEGER Enumeration
unknown(0) detection(1) disconnection(2) notapplicable(3)
dormantdisconnection(4) dormantdetection(5)
Object StarShortName
Object ID
N/A Description
short identification string. Follows the same conventions as the
DisplayString TEXTUAL-CONVENTION.
Syntax
Octet String (1..32)
Object
StarShortID
Object ID
N/A Description
An abbreviated form for identifying a service, composed of the
first 8 characters of the context name, and the first 8 characters
of a service name, separated by (:)
Syntax
OCTET STRING(1..17)
Object StarMediumID
Object ID
N/A Description
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
14 OL-23912-02
An abbreviated form for identifying a context-specific object,
composed of the first 8 characters of the context name, and the
first 16 characters of the object name, separated by (:)
Syntax
OCTET STRING (SIZE (1..25))
Object StarQOSTPAction
Object ID N/A
Description
Traffic Policing Action Syntax
INTEGER Enumeration
unknown(0) notapplicable(1) transmit(2) drop(3)
loweripprecedence(4)
Object StarOSPFNeighborState
Object ID
N/A Description
OSPF Neighbor State Syntax
INTEGER Enumeration
unknown(0), down(1), attempt(2), init(3), twoway(4), exstart(5),
exchange(6), loading(7),
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 15
full(8)
starentMIB(8164).starentMIBObjects(1).starentChassis(1)
Object
starChassisCriticalCO
Object ID
enterprises.8164.1.1.1 Description
The current state of the Critical Central Office (CO) relay.
Syntax
StarRelayState Access
Read-only
Object starChassisMajorCO
Object ID enterprises.8164.1.1.2
Description
The current state of the Major Central Office (CO) relay.
Syntax
StarRelayState Access
Read-only
Object
starChassisMinorCO
Object ID
enterprises.8164.1.1.3 Description
The current state of the Minor Central Office (CO) relay.
Syntax
StarRelayState Access
Read-only
Object
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
16 OL-23912-02
starChassisAction
Object ID enterprises.8164.1.1.5
Description
Trigger to perform certain system-wide operations. noaction (1)
performs no operation. It is the normal value received when this
attribute is read. testled (2) triggers a test of all of the LEDs
in the system. aco (3) triggers the Alarm Cut-Off, which shuts off
all of the Central Office (CO) audible/visual relays. reset (4)
triggers a system-wide restart. It will completely disrupt service
on the device.
Syntax
Integer Access
Read-write Enumeration
noaction(1) testled(2) aco(3) reset(4)
Object starTimeTicks
Object ID enterprises.8164.1.1.6
Description
The number of system clock ticks since the last system Epoch.
One system clock tick is 10 milliseconds.
Syntax Unsigned32
Access
Read-only
Object
starChassisAudibleAlarm
Object ID
enterprises.8164.1.1.7 Description
The current state of the chassis Audible Alarm. Syntax
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 17
StarRelayState Access
Read-only
Object starChassisUTCTime
Object ID
enterprises.8164.1.1.8 Description
The current time on the chassis, in UTC format Syntax
DateAndTime Access
Read-only
Object starChassisLocalTime
Object ID
enterprises.8164.1.1.9 Description
The current time on the chassis, converted to the local time
zone Syntax
DateAndTime Access
Read-only
Object starChassisType
Object ID enterprises.8164.1.1.10
Description
The physical chassis type Syntax
Integer Access
Read-only Enumeration
unknown(0)
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
18 OL-23912-02
ST16(1) ST40(2) XT2(3) st20(4)
Object starChassisDescription
Object ID
enterprises.8164.1.1.11 Description
Chassis description Syntax
DisplayString Access
Read-Only
Object starChassisSWRevision
Object ID
enterprises.8164.1.1.12 Description
Software revision Syntax
DisplayString Access
Read-Only Object
starChassisPeakMemoryUsage Object ID
enterprises.8164.1.1.13 Description
The system level peak memory usage, in kilobytes, rounded down
(i.e. 1023 bytes = 0kilobytes)
Syntax
Integer32(1..2097152) Access
Read-Only
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 19
starentMIB(8164).starentMIBObjects(1).starentSlots(2) Object
starSlotTable
Object ID
enterprises.8164.1.2.1 Description
A table containing information on all of the slots. Syntax
Sequence of StarSlotEntry Access
Not-accessible
Object starSlotEntry
Object ID enterprises.8164.1.2.1.1
Description
Information about a particular slot. Syntax
StarSlotEntry Access
Not-accessible Sequence
starSlotNum starSlotType starCardType starCardOperState
starCardAdminState starCardRevision starCardLastStateChange
starCardMode starCardDesiredMode starCardPacStandbyPriority
starCardLock starCardHaltIssued starCardRebootPending
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
20 OL-23912-02
starCardUsable starCardSinglePOF starCardAttachment
starCardTemperature starSlotVoltage1dot5
starSlotVoltage1dot5LowThresh starSlotVoltage1dot5HighThresh
starSlotVoltage1dot8 starSlotVoltage1dot8LowThresh
starSlotVoltage1dot8HighThresh starSlotVoltage2dot5
starSlotVoltage2dot5LowThresh starSlotVoltage2dot5HighThresh
starSlotVoltage3dot3 starSlotVoltage3dot3LowThresh
starSlotVoltage3dot3HighThresh starSlotVoltage5dot0
starSlotVoltage5dot0LowThresh starSlotVoltage5dot0HighThresh
starSlotNumPorts starSlotVoltageState starSlotNumCpu
starSlotNum
Object ID
enterprises.8164.1.2.1.1.1 Description
The slot number. Syntax
Integer32(1..48) Access
Not-accessible
Object starSlotType
Object ID enterprises.8164.1.2.1.1.2
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 21
Description
The type of the slot. Syntax
StarentSlotType Access
Read-only
Object starCardType
Object ID
enterprises.8164.1.2.1.1.3 Description
The type of the card which is plugged into a slot. Syntax
StarentCardType Access
Read-only
Object starCardOperState
Object ID
enterprises.8164.1.2.1.1.4 Description
The current operational state of the card. Syntax
Integer Access
Read-only Enumeration
unknown(1) empty(2) offline(3) booting(4) ready(5) standby(6)
active(7) migratefrom(8)
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
22 OL-23912-02
migrateto(9)
Object starCardAdminState
Object ID enterprises.8164.1.2.1.1.5
Description
The current administrative state of the card. Syntax
Integer Access
Read-only Enumeration
unknown(1) enabled(2) disabled(3)
Object starCardRevision
Object ID enterprises.8164.1.2.1.1.6
Description
The revision number of the card that is physically present in
this slot. Syntax
StarentVersionNum Access
Read-only
Object
starCardLastStateChange
Object ID
enterprises.8164.1.2.1.1.7 Description
The time when the last state change occurred for this row. A
manager could poll this variable to determine if information has
changed.
Syntax
DateAndTime Access
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 23
Read-only
Object starCardMode
Object ID enterprises.8164.1.2.1.1.8
Description
The desired mode of the card. This field is applicable only to
slots which can contain PAC/PSC and TAC cards. The active(4) value
is obsolete and has been replaces with activepac(5) and
activetac(6).
Syntax
Integer Access
Read-only Enumeration
unknown(1) notapplicable(2) standby(3) active(4) activepac(5)
activetac(6) activepsc(7) activevpc(8)
Object
starCardPacStandbyPriority
Object ID
enterprises.8164.1.2.1.1.9 Description
Specifies the standby priority of the packet accelerator card.
Syntax
Gauge32 Access
Read-only
Object starCardHaltIssued
Object ID
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
24 OL-23912-02
enterprises.8164.1.2.1.1.10 Description
Only applicable to SPC cards. Syntax
Integer Access
Read-only Enumeration
notapplicable(1) yes(2) no(3)
Object starCardLock
Object ID
enterprises.8164.1.2.1.1.11 Description
Identifies if the card lock is currently engaged. A value of
locked(2) means that the lock is engaged, and thus the card could
not be removed from the chassis. A value of unlocked(3) means that
the lock is not engaged, and an operator could remove the card from
the chassis. A value of unknown(1) should represent that there is
no card physically in the slot.
Syntax
Integer Access
Read-only Enumeration
unknown(1) locked(2) unlocked(3)
Object
starCardRebootPending
Object ID
enterprises.8164.1.2.1.1.12 Description
Identifies if a reboot operation is currently pending for this
card. Syntax
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 25
Integer Access
Read-only Enumeration
no(1) yes(2)
Object starCardUsable
Object ID
enterprises.8164.1.2.1.1.13 Description
Indicates if the card is currently usable. Syntax
Integer Access
Read-only Enumeration
no(1) yes(2)
Object starCardSinglePOF
Object ID
enterprises.8164.1.2.1.1.14 Description
Identifies if this card represents a single point of failure
(POF). A value of no(1) indicates that this card is supported by a
redundant card which can take over in the event of a failure. A
value of yes(2) indicates that this card does not have a redundant
partner, and that a failure of this card could result in service
interruption.
Syntax Integer
Access
Read-only Enumeration
notapplicable(1) no(2) yes(3)
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
26 OL-23912-02
Object starCardAttachment
Object ID
enterprises.8164.1.2.1.1.15 Description
Identifies if the card is currently attached to another card (a
PAC/PSC attached to a line card, or visa versa, for example)
Syntax Integer
Access
Read-only Enumeration
connected(1) unconnected(2)
Object starCardTemperature
Object ID enterprises.8164.1.2.1.1.16
Description
The temperature, in degrees Celsius, as measured on the card. A
value of 0 indicates that the temperature cannot be read, or that
the card is not present. The maximum measurable temperature is 70
C.
Syntax
Gauge32 Access
Read-only
Object starSlotVoltage1dot5
Object ID
enterprises.8164.1.2.1.1.20 Description
The current voltage, in millivolts, of the nominal 1.5V power
supply. The working range for this card is the range defined by
variables starSlotVoltage1dot5LowThresh and
starSlotVoltage1dot5HighThresh. A value of 0 indicates that the
voltage cannot be read, or that the card is not present.
Syntax Gauge32
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 27
Access
Read-only
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification.
Object starSlotVoltage1dot5LowThresh
Object ID enterprises.8164.1.2.1.1.21
Description
The voltage level, in millivolts, which is the lowest allowable
value for the nominal 1.5V power supply. A value of 0 indicates
that there is no card present.
Syntax
Gauge32 Access
Read-only
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification.
Object starSlotVoltage1dot5HighThresh
Object ID
enterprises.8164.1.2.1.1.22 Description
The voltage level, in millivolts, which is the highest allowable
value for the nominal 1.5V power supply. A value of 0 indicates
that there is no card present.
Syntax
Gauge32 Access
Read-only
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification.
Object starSlotVoltage1dot8
Object ID
enterprises.8164.1.2.1.1.23
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
28 OL-23912-02
Description
The current voltage, in millivolts, of the nominal 1.8V power
supply. The working range for this card is the range defined by
variables starSlotVoltage1dot8LowThresh and
starSlotVoltage1dot8HighThresh. A value of 0 indicates that the
voltage cannot be read, or that the card is not present.
Syntax
Gauge32 Access
Read-only
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification
Object starSlotVoltage1dot8LowThresh
Object ID
enterprises.8164.1.2.1.1.24 Description
The voltage level, in millivolts, which is the lowest allowable
value for the nominal 1.8V power supply. A value of 0 indicates
that there is no card present.
Syntax Gauge32
Access
Read-only
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification.
Object starSlotVoltage1dot8HighThresh
Object ID enterprises.8164.1.2.1.1.25
Description
The voltage level, in millivolts, which is the highest allowable
value for the nominal 1.8V power supply. A value of 0 indicates
that there is no card present.
Syntax
Gauge32 Access
Read-only
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 29
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification.
Object starSlotVoltage2dot5
Object ID enterprises.8164.1.2.1.1.26
Description
The current voltage, in millivolts, of the nominal 2.5V power
supply. The working range for this card is the range defined by
variables starSlotVoltage2dot5LowThresh and
starSlotVoltage2dot5HighThresh. A value of 0 indicates that the
voltage cannot be read, or that the card is not present.
Syntax
Gauge32 Access
Read-only
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification.
Object starSlotVoltage2dot5LowThresh
Object ID
enterprises.8164.1.2.1.1.27 Description
The voltage level, in millivolts, which is the lowest allowable
value for the nominal 2.5V power supply. A value of 0 indicates
that there is no card present.
Syntax Gauge32
Access
Read-only
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification.
Object starSlotVoltage2dot5HighThresh
Object ID
enterprises.8164.1.2.1.1.28 Description
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
30 OL-23912-02
The voltage level, in millivolts, which is the highest allowable
value for the nominal 2.5V power supply. A value of 0 indicates
that there is no card present.
Syntax Gauge32
Access
Read-only
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification.
Object starSlotVoltage3dot3
Object ID enterprises.8164.1.2.1.1.29
Description
The current voltage, in millivolts, of the nominal 3.3V power
supply. The working range for this card is the range defined by
variables starSlotVoltage3dot3LowThresh and
starSlotVoltage3dot3HighThresh. A value of 0 indicates that the
voltage cannot be read, or that the card is not present.
Syntax
Gauge32 Access
Read-only
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification.
Object starSlotVoltage3dot3LowThresh
Object ID
enterprises.8164.1.2.1.1.30 Description
The voltage level, in millivolts, which is the lowest allowable
value for the nominal 3.3V power supply. A value of 0 indicates
that there is no card present.
Syntax Gauge32
Access
Read-only
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification.
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 31
Object starSlotVoltage3dot3HighThresh
Object ID
enterprises.8164.1.2.1.1.31 Description
The voltage level, in millivolts, which is the highest allowable
value for the nominal 3.3V power supply. A value of 0 indicates
that there is no card present.
Syntax Gauge32
Access
Read-only
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification.
Object starSlotVoltage5dot0
Object ID enterprises.8164.1.2.1.1.32
Description
The current voltage, in millivolts, of the nominal 5.0V power
supply. The working range for this card is the range defined by
variables starSlotVoltage5dot0LowThresh and
starSlotVoltage5dot0HighThresh. A value of 0 indicates that the
voltage cannot be read, or that the card is not present.
Syntax
Gauge32 Access
Read-only
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification.
Object starSlotVoltage5dot0LowThresh
Object ID
enterprises.8164.1.2.1.1.33 Description
The voltage level, in millivolts, which is the lowest allowable
value for the nominal 5.0V power supply. A value of 0 indicates
that there is no card present.
Syntax
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
32 OL-23912-02
Gauge32 Access
Read-only
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification.
Object
starSlotVoltage5dot0HighThresh
Object ID
enterprises.8164.1.2.1.1.34 Description
The voltage level, in millivolts, which is the highest allowable
value for the nominal 5.0V power supply. A value of 0 indicates
that there is no card present.
Syntax
Gauge32 Access
Read-only
Important: This alarm is obsolete. System uses
starSlotVoltageState alarm for this notification
Object starSlotNumPorts
Object ID
enterprises.8164.1.2.1.1.35 Description
Number of data ports on this card. This value will be 0 for
cards that no not contain ports, such as SPC/PAC/TAC cards, or for
slots which do not contain a card.
Syntax Gauge32
Access
Read-only
Important: This alarm is obsolete.
Object starSlotAction
Object ID
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 33
enterprises.8164.1.2.1.1.36 Description
Trigger to perform certain slot operations. noaction(1) performs
no operation. It is the normal value received when this attribute
is read. reset(2) causes the slot to be reset.
Syntax
Integer Access
Read-write Enumeration
noaction(1) reset(2)
Object starSlotVoltageState
Object ID
enterprises.8164.1.2.1.1.37 Description
The state of the voltage supplies on the card. A value of
unknown(0) means that the state cannot be identified; normal(1)
represents a properly functioning card; outofrange(2) indicates
that one or more voltage sources are not within their specified
operating range.
Syntax Integer
Access
Read-only Enumeration
unknown(0) normal(1) outfrange(2)
Object starSlotNumCpu
Object ID enterprises.8164.1.2.1.1.38
Description
The number of general purpose CPU on this card. Syntax
Integer32 Access
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
34 OL-23912-02
Read-only
Object starSlotPartNumber
Object ID enterprises.8164.1.2.1.1.39
Description
The part number of this card. Syntax
DisplayString Access
Read-only
Object starSlotPartRevision
Object ID enterprises.8164.1.2.1.1.40
Description
The revision number of this card. Syntax
DisplayString Access
Read-only
Object starSlotSerialNumber
Object ID
enterprises.8164.1.2.1.1.41 Description
The serial number of this card. Syntax
DisplayString Access
Read-only
Object starSlotCLEICode
Object ID
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 35
enterprises.8164.1.2.1.1.42 Description
The CLEI code of this card. Syntax
DisplayString Access
Read-only
Object starSlotCiscoModelName
Object ID
enterprises.8164.1.2.1.1.43 Description
Cisco-defined Product Identifier (PID). The PID is an
alphanumeric identifier used to identify specific Cisco product
hardware, and may be up to 18 characters in length.
starSlotCiscoModelName will be blank (zero characters) if no PID is
available.
Syntax DisplayString
Access
Read-only
Object starSlotCiscoHardwareRev
Object ID
enterprises.8164.1.2.1.1.44 Description
Cisco-defined Version Identifier (VID). The VID is used to track
the version of the Customer-Orderable Cisco Product Identifier
(PID) [starSlotCiscoModelName]. The data convention for VID is 'V'
followed by a two digit number. VID numbering typically begins at
'V01' but can be initiated at a higher value.
starSlotCiscoModelName will be blank (zero characters) if no PID is
available.
Syntax DisplayString
Access
Read-only
Object starSlotCiscoSerialNumber
Object ID
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
36 OL-23912-02
enterprises.8164.1.2.1.1.45 Description
Cisco-defined Serial Number (SN). The SN is an 11 character
identifier used in conjunction with the Cisco Product Identifier
(PID) [starSlotCiscoModelName] to identify a unique product or
Field Replaceable Unit (FRU) of a product.
starSlotCiscoSerialNumber will be blank (zero characters) if no VID
is available.
Syntax DisplayString
Access
Read-only
starentMIB(8164).starentMIBObjects(1).starentSlotMapping(3)
Object
starSlotMappingTable
Object ID enterprises.8164.1.3.1
Description
A table identifying all of the slot mappings. Syntax
Sequence of StarSlotMappingEntry Access
Not-accessible
Object starSlotMappingEntry
Object ID
enterprises.8164.1.3.1.1 Description
Information about a particular slot mapping. Syntax
StarSlotMappingEntry Access
Not-accessible Sequence
starSlotMappingNum Index starSlotMappingType
starSlotMappingRCCNum
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 37
starSlotMappingToSlot
Object starSlotMappingNum
Object ID enterprises.8164.1.3.1.1.1
Description
The slot number. This always represents a slot in the back of
the chassis. Syntax
Integer32(17..48) Access
Not-accessible Description
The slot number. This always represents a slot in the back of
the chassis.
Object starSlotMappingType
Object ID
enterprises.8164.1.3.1.1.2 Description
The type of the slot mapping. The value none(1) represents that
there is no mapping, which typically represents that there is no
card present in this slot.
Syntax Integer
Access
Read-only Enumeration
unknown(1) none(2) direct(3) rcc(4) cross(5)
Object starSlotMappingRCCNum
Object ID
enterprises.8164.1.3.1.1.3 Description
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
38 OL-23912-02
Identifies which RCC card is responsible for this mapping. This
value is only valid if the value of starSlotMappingType is
rcc(3).
Syntax Integer32(0..2)
Access
Read-only
Object starSlotMappingToSlot
Object ID
enterprises.8164.1.3.1.1.4 Description
The slot number this slot is mapped to. This always represents a
slot in the front of the chassis.
Syntax
Integer32(1..16) Access
Read-only
starentMIB(8164).starentMIBObjects(1).starentFans(4) Object
starFanTable
Object ID
enterprises.8164.1.4.1 Description
A table containing information on all of the fan controllers.
Syntax
Sequence of StarFanEntry Access
Not-accessible
Object starFanEntry
Object ID
enterprises.8164.1.4.1.1 Description
Information about a particular fan controller.
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 39
Syntax
StarFanEntry Access
Not-accessible Sequence
starFanNum Index starFanLocation starFanStatus starFanSpeed
Object starFanNum
Object ID enterprises.8164.1.4.1.1.1
Description
The fan controller number. Syntax
Integer32(1..2) Access
Not-accessible
Object starFanLocation
Object ID
enterprises.8164.1.4.1.1.2 Description
The physical location of the fan controller. Syntax
Integer Access
Read-only Enumeration
upper(1) lower(2)
Object starFanStatus
Object ID
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
40 OL-23912-02
enterprises.8164.1.4.1.1.3 Description
A bitmask representing the status of the fan tray. A normal,
properly functioning fan tray would show 0x101 (257 decimal),
meaning it is present (0x100) and all fans are working (0x1).
Syntax
Integer32 Access
Read-only Enumeration
0x01 All Fans Good 0x02 Multiple Fans Bad 0x04 Single Fan Bad
0x08 HB Error 0x10 COM A Error 0x20 COM B Error 0x40 COMM Error
0x80 Not Present 0x100 Present 0x200 Filter Clogged 0x400 State
Unknown
Object starFanSpeed
Object ID
enterprises.8164.1.4.1.1.4 Description
The speed of the fans controlled by this fan controller. The
values represent the percentage that the speed is running relative
to the maximum possible speed, speed100(12)
Syntax
Integer Access
Read-only Enumeration
unknown(1) speed50(2) speed55(3)
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 41
speed60(4) speed65(5) speed70(6) speed75(7) speed80(8)
speed85(9) speed90(10) speed95(11) speed100(12)
starentMIB(8164).starentMIBObjects(1).starentLogs(5) The objects
in this table are not accessible via SNMP. They are intended for
use within traps.
Object starLogTable
Object ID
enterprises.8164.1.5.1 Description
A table containing information about all of the system logs.
Syntax
Sequence of StarLogEntry Access
Not-accessible
Object starLogEntry
Object ID
enterprises.8164.1.5.1.1 Description
Information about a particular system log. Syntax
StarLogEntry Access
Not-accessible Sequence
starLogName Index
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
42 OL-23912-02
starLogCurSize starLogMaxSize starLogText
Object
starLogName
Object ID
enterprises.8164.1.5.1.1.1 Description
The name of the system log. Syntax
StarShortName Access
Not-accessible
Object starLogCurSize
Object ID
enterprises.8164.1.5.1.1.2 Description
The size, in bytes, of this log. Syntax
Gauge32 Access
Read-only
Object starLogMaxSize
Object ID
enterprises.8164.1.5.1.1.3 Description
The maximum size, in bytes, of this log. Syntax
Gauge32 Access
Read-only
Object
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 43
starLogText
Object ID enterprises.8164.1.5.1.1.4
Description
For use in LogMsg trap. Syntax
Octet String (SIZE (1..512)) Access
Read-only
starentMIB(8164).starentMIBObjects(1).starentAlertMan(8)
starentFeedback(1) Object
starMaxAlertsPerTime
Object ID
enterprises.8164.1.8.1.1 Description
The maximum number of SNMP Traps which will be sent within the
time period specified by starWindowTime.
Syntax Gauge32
Access
Read-only
Object starWindowTime
Object ID
enterprises.8164.1.8.1.2 Description
The amount of time, in seconds, within which no more than
starMaxAlertsPerTime SNMP Traps will be sent.
Syntax
Unsigned32 Access
Read-only
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
44 OL-23912-02
Object starAlertSendingEnabled
Object ID
enterprises.8164.1.8.1.3 Description
Shows if SNMP traps are currently enabled or disabled. Traps are
disabled when more than starMaxAlertsPerTime traps are sent within
the starWindowTime time period. A value of true(1) indicates that
traps will still be sent. A value of false(2) indicates that traps
are no longer being generated
Syntax
TruthValue Access
Read-only
starentMIB(8164).starentMIBObjects(1).starentPower(9) Object
starPowerTable
Object ID
enterprises.8164.1.9.1 Description
A table containing information about all power filters.
Syntax
Sequence of StarPowerEntry Access
Not-accessible
Object starPowerEntry
Object ID
enterprises.8164.1.9.1.1 Description
Information about a particular power filter. Syntax
StarPowerEntry Access
Not-accessible Sequence
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 45
starPowerNumber Index starPowerState
Object starPowerNumber
Object ID enterprises.8164.1.9.1.1.1
Description
The identifying number for this power filter. Syntax
Integer Access
Not-accessible Enumeration
powerA(1) powerB(2)
Object starPowerState
Object ID enterprises.8164.1.9.1.1.2
Description
The state of the power filter. The value active(1) means that
the power filter is present and operational. The value failed(2)
means that the power filter is present, but not operational. The
value not-present(3) means that the power filter is not physically
present in the system.
Syntax
Integer Access
Read-only Enumeration
active(1) failed(2) notpresent(3)
starentMIB(8164).starentMIBObjects(1).starentCPU(10) Object
starCPUTable
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
46 OL-23912-02
Object ID
enterprises.8164.1.10.1 Description
A table containing information about all CPUs Syntax
Sequence of StarCPUEntry Access
Not-accessible
Object starCPUEntry
Object ID enterprises.8164.1.10.1.1
Description
Information about a particular CPU. Syntax
StarCPUEntry Access
Not-accessible Sequence
starCPUSlot Index starCPUNumber Index starCPUUser starCPUSystem
starCPUIdle starCPUIO starCPURQ starCPULoad1Min starCPULoad5Min
starCPULoad15Min starCPUMemTotal starCPUMemUsed starCPUNumProcesses
starCPUMemCached
Object starCPUSlot
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 47
Object ID
enterprises.8164.1.10.1.1.1 Description
The slot number of the card holding this CPU. Syntax
Integer32(1..16) Access
Not-accessible
Object starCPUNumber
Object ID enterprises.8164.1.10.1.1.2
Description
The CPU number within this card. Numbers begin at 0. Syntax
Integer32(0..3) Access
Not-accessible
Object starCPUUser
Object ID
enterprises.8164.1.10.1.1.3 Description
Percentage of the CPU spent running user processes. starCPUUser
is the percentage value times 100; for example, 2.3% would be
represented as 230
Syntax
Integer32(1..10000) Access
Read-only
Object starCPUSystem
Object ID
enterprises.8164.1.10.1.1.4 Description
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
48 OL-23912-02
Percentage of the CPU spent running system processes.
starCPUSystem is the percentage value times 100; for example, 2.3%
would be represented as 230.
Syntax Integer32(1..10000)
Access
Read-only
Object starCPUIdle
Object ID
enterprises.8164.1.10.1.1.6 Description
Percentage of the CPU spent idle. starCPUIdle is the percentage
value times 100; for example, 2.3% would be represented as 230.
Syntax
Integer32(1..10000) Access
Read-only
Object starCPUIO
Object ID
enterprises.8164.1.10.1.1.7 Description
Percentage of the CPU spent running Input/Output processes.
starCPUIO is the percentage value times 100; for example, 2.3%
would be represented as 230.
Syntax Integer32(1..10000)
Access
Read-only
Object starCPURQ
Object ID enterprises.8164.1.10.1.1.8
Description
Percentage of the CPU spent running IRQ processes. starCPURQ is
the percentage value times 100; for example, 2.3% would be
represented as 230.
Syntax
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 49
Integer32(1..10000) Access
Read-only
Object starCPULoad1Min
Object ID
enterprises.8164.1.10.1.1.11 Description
The average CPU load over the last minute. The CPU load is
defined to be the number of processes who are ready to run.
starCPULoad1Min is the average number of processes times 100; for
example, 2.45 would be represented as 245.
Syntax Integer32(1..1000000000)
Access
Read-only
Object starCPULoad5Min
Object ID enterprises.8164.1.10.1.1.12
Description
The average CPU load over the last 5 minutes. The CPU load is
defined to be the number of processes who are ready to run.
starCPULoad5Min is the average number of processes times 100; for
example, 2.45 would be represented as 245.
Syntax
Integer32(1..1000000000) Access
Read-only
Object starCPULoad15Min
Object ID
enterprises.8164.1.10.1.1.13 Description
The average CPU load over the last 15 minutes. The CPU load is
defined to be the number of processes who are ready to run.
starCPULoad15Min is the average number of processes times 100; for
example, 2.45 would be represented as 245.
Syntax Integer32(1..1000000000)
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
50 OL-23912-02
Access
Read-only
Object
starCPUMemTotal
Object ID
enterprises.8164.1.10.1.1.14 Description
The total amount of memory dedicated to this CPU, in kilobytes.
Syntax
Integer32(1..2097152) Access
Read-only
Object starCPUMemUsed
Object ID
enterprises.8164.1.10.1.1.15 Description
The total amount of memory consumed by this CPU, in kilobytes.
Syntax
Integer32(1..2097152) Access
Read-only
Object starCPUNumProcesses
Object ID enterprises.8164.1.10.1.1.16
Description
The total number of processes which exist on this CPU.
Syntax
Integer32(1..4096) Access
Read-only
Object starCPUMemCached
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 51
Object ID
enterprises.8164.1.10.1.1.17 Description
The total amount of memory consumed by the (reusable) memory
cache on this CPU, in kilobytes
Syntax Integer32(1..2097152)
Access
Read-only
starentMIB(8164).starentMIBObjects(1).starentNPUMgr(11) The
objects in this table are not accessible via SNMP. They are
intended for use within traps.
Object
starNPUMgrTable
Object ID enterprises.8164.1.11.1
Description
A table containing information about all NPU Managers.
Syntax
Sequence of StarNPUMgrEntry Access
Not-accessible
Object starNPUMgrEntry
Object ID
enterprises.8164.1.11.1.1 Description
Information about a particular NPU Manager. Syntax
StarNPUMgrEntry Access
Not-accessible Sequence
starNPUMgrNumber
Object
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
52 OL-23912-02
starNPUMgrNumber
Object ID enterprises.8164.1.11.1.1.1
Description
The identity of this NPU. Syntax
Integer32(1..65535) Access
Not-accessible
starentMIB(8164).starentMIBObjects(1).starentSessInP(12)
Object
starSessInProgCalls
Object ID enterprises.8164.1.12.1
Description
The number of sessions currently in progress. Syntax
Gauge32 Access
Read-only
Object starSessInProgActiveCalls
Object ID
enterprises.8164.1.12.2 Description
The number of sessions with active calls. Syntax
Gauge32 Access
Read-only
Object starSessInProgDormantCalls
Object ID
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 53
enterprises.8164.1.12.3 Description
The number of sessions associated with dormant calls. Syntax
Gauge32 Access
Read-only
Object starSessInProgArrived
Object ID
enterprises.8164.1.12.4 Description
The number of sessions in the arrived state. Syntax
Gauge32 Access
Read-only
Object starSessInProgLCPNeg
Object ID enterprises.8164.1.12.5
Description
The number of sessions in the link control protocol negotiation
state. Syntax
Gauge32 Access
Read-only
Object starSessInProgLCPUp
Object ID enterprises.8164.1.12.6
Description
The number of sessions in the link control protocol up state.
Syntax
Gauge32
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
54 OL-23912-02
Access
Read-only
Object
starSessInProgAuthenticating
Object ID
enterprises.8164.1.12.7 Description
The number of sessions in the authenticating state. Syntax
Gauge32 Access
Read-only
Object starSessInProgAuthenticated
Object ID
enterprises.8164.1.12.8 Description
The number of sessions in the authenticated state. Syntax
Gauge32 Access
Read-only
Object starSessInProgIPCPUp
Object ID enterprises.8164.1.12.9
Description
The number of sessions in the IP control protocol up state.
Syntax
Gauge32 Access
Read-only
Object starSessInProgSIPConn
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 55
Object ID
enterprises.8164.1.12.10 Description
The number of sessions in the Simple IP connected state.
Syntax
Gauge32 Access
Read-only
Object starSessInProgMIPConn
Object ID enterprises.8164.1.12.11
Description
The number of sessions in the Mobile IP connected state.
Syntax
Gauge32 Access
Read-only
Object starSessInProgDisc
Object ID
enterprises.8164.1.12.12 Description
The number of sessions in the disconnecting state. Syntax
Gauge32 Access
Read-only
starentMIB(8164).starentMIBObjects(1).starentSessMgr(13)
Object
starSessMgrCount
Object ID
enterprises.8164.1.13.1
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
56 OL-23912-02
Description
The total number of session manager instances. Syntax
Gauge32 Access
Read-only
Object starSessTtlArrived
Object ID
enterprises.8164.1.13.2 Description
The total number of requested sessions. Syntax
Gauge32 Access
Read-only
Object starSessTtlRejected
Object ID
enterprises.8164.1.13.3 Description
The total number of rejected sessions. Syntax
Gauge32 Access
Read-only
Object starSessTtlConnected
Object ID enterprises.8164.1.13.4
Description
The total number of sessions which were connected. Syntax
Gauge32 Access
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 57
Read-only
Object starSessTtlAuthSucc
Object ID enterprises.8164.1.13.5
Description
The total number of sessions where authentication was
successful. Syntax
Gauge32 Access
Read-only
Object starSessTtlAuthFail
Object ID enterprises.8164.1.13.6
Description
The total number of sessions which failed authentication.
Syntax
Gauge32 Access
Read-only
Object starSessTtlLCPUp
Object ID
enterprises.8164.1.13.7 Description
The total number of sessions in the link control protocol in the
up state. Syntax
Gauge32 Access
Read-only
Object starSessTtlIPCPUp
Object ID
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
58 OL-23912-02
enterprises.8164.1.13.8 Description
The total number of sessions in the IP control protocol up
state. Syntax
Gauge32 Access
Read-only
Object starSessTtlSrcViol
Object ID
enterprises.8164.1.13.9 Description
The total number of sessions which had an invalid source.
Syntax
Gauge32 Access
Read-only
Object starSessTtlKeepFail
Object ID enterprises.8164.1.13.10
Description
The total number of sessions which had a keep alive failure.
Syntax
Gauge32 Access
Read-only
Object starSessTtlOctForwarded
Object ID enterprises.8164.1.13.11
Description
The total number of octets forwarded (data + control).
Syntax
Counter32
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 59
Units
Megabytes Access
Read-only
Object starSessTtlRPRegAccept
Object ID enterprises.8164.1.13.12
Description
The total number of Initial RRQ Accepted. Syntax
Counter32 Access
Read-only
Object starSessTtlRPRegAcceptInterPDSN
Object ID enterprises.8164.1.13.13
Description
The total number of Inter PDSN Handoff RRQ Accepted. Syntax
Counter32 Access
Read-only
Object starPPPCurrSessions
Object ID
enterprises.8164.1.13.14 Description
The current number of PPP sessions Syntax
Counter32 Access
Read-only
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
60 OL-23912-02
Object starSessTtlTxBytes
Object ID
enterprises.8164.1.13.15 Description
The total number of bytes transmitted from mobiles Syntax
Counter32 Units
Megabytes Access
Read-only
Object starSessTtlRxBytes
Object ID
enterprises.8164.1.13.16 Description
he total number of bytes received by mobiles Syntax
Counter32 Units
Megabytes Access
Read-only
Object starSessTtlSIPTxBytes
Object ID
enterprises.8164.1.13.17 Description
The total number of bytes transmitted from mobiles using SIP
Syntax
Counter32 Units
Megabytes Access
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 61
Read-only
Object starSessTtlSIPRxBytes
Object ID enterprises.8164.1.13.18
Description
The total number of bytes received by mobiles using SIP
Syntax
Counter32 Units
Megabytes Access
Read-only
Object starSessTtlMIPTxBytes
Object ID
enterprises.8164.1.13.19 Description
The total number of bytes transmitted from mobiles using MIP
Syntax
Counter32 Units
Megabytes Access
Read-only
Object starSessTtlMIPRxBytes
Object ID
enterprises.8164.1.13.20 Description
The total number of bytes received by mobiles using MIP
Syntax
Counter32 Units
Megabytes
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
62 OL-23912-02
Access
Read-only
Object
starSessTtlOctForwardedGB
Object ID
enterprises.8164.1.13.21 Description
The total number of octets forwarded (data + control) Syntax
Counter32 Units
Gigabytes Access
read-only
starentMIB(8164).starentMIBObjects(1).starentAAAMgr(14)
Object
starAAAMgrCount
Object ID enterprises.8164.1.14.1
Description
The total number of AAA manager instances. Syntax
Gauge32 Access
Read-only
Object starAAATtlRequests
Object ID
enterprises.8164.1.14.2 Description
The total number of AAA requests. Syntax
Gauge32
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 63
Access
Read-only
Object
starAAATtlAuthRequests
Object ID
enterprises.8164.1.14.3 Description
The total number of AAA authentication requests. Syntax
Gauge32 Access
Read-only
Object starAAATtlAcctRequests
Object ID
enterprises.8164.1.14.4 Description
The total number of AAA accounting requests. Syntax
Gauge32 Access
Read-only
Object starAAACurRequests
Object ID enterprises.8164.1.14.5
Description
The current number of AAA requests. Syntax
Gauge32 Access
Read-only
Object starAAACurAuthRequests
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
64 OL-23912-02
Object ID
enterprises.8164.1.14.6 Description
The current number of AAA authentication requests. Syntax
Gauge32 Access
Read-only
Object starAAACurAcctRequests
Object ID enterprises.8164.1.14.7
Description
The current number of AAA accounting requests. Syntax
Gauge32 Access
Read-only
Object starAAATtlAcctSess
Object ID
enterprises.8164.1.14.8 Description
The total number of AAA accounting sessions. Syntax
Gauge32 Access
Read-only
Object starAAACurAcctSess
Object ID
enterprises.8164.1.14.9 Description
The current number of accounting sessions Syntax
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 65
Gauge32 Access
Read-only
Object starAAATtlAuthSuccess
Object ID
enterprises.8164.1.14.10 Description
The total number of AAA authentication successes. Syntax
Gauge32 Access
Read-only
Object starAAATtlAuthFailure
Object ID
enterprises.8164.1.14.11 Description
The total number of AAA authentication failures. Syntax
Gauge32 Access
Read-only
starentMIB(8164).starentMIBObjects(1).starentA11Mgr(15)
Object
starA11MgrCount
Object ID enterprises.8164.1.15.1
Description
The total number of A11 manager instances. Syntax
Gauge32 Access
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
66 OL-23912-02
Read-only
Object starA11TtlArrived
Object ID enterprises.8164.1.15.2
Description
The total number of A11 session requests. Syntax
Gauge32 Access
Read-only
Object starA11TtlRejected
Object ID enterprises.8164.1.15.3
Description
The total number of rejected A11 sessions. Syntax
Gauge32 Access
Read-only
Object starA11TtlDemultiplexed
Object ID
enterprises.8164.1.15.4 Description
The total number of demultiplexed A11 sessions. Syntax
Counter32 Access
Read-only
Object starA11TtlDereg
Object ID
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 67
enterprises.8164.1.15.5 Description
The total number of A11 deregistrations. Syntax
Counter32 Access
Read-only
Object starA11CurActive
Object ID
enterprises.8164.1.15.6 Description
The current number of active A11 sessions. Syntax
Gauge32 Access
Read-only
starentMIB(8164).starentMIBObjects(1).starentHAMgr(16)
Object
starHAMgrCount
Object ID
enterprises.8164.1.16.1 Description
The total number of home agent manager instances. Syntax
Gauge32 Access
Read-only
Object starHATtlArrived
Object ID enterprises.8164.1.16.2
Description
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
68 OL-23912-02
The total number of home agent session requests. Syntax
Counter32 Access
Read-only
Object starHATtlRejected
Object ID enterprises.8164.1.16.3
Description
The total number of rejected home agent sessions. Syntax
Counter32 Access
Read-only
Object
starHATtlDemultiplexed
Object ID
enterprises.8164.1.16.4 Description
The total number of demultiplexed home agent sessions.
Syntax
Counter32 Access
Read-only
Object starHATtlDereg
Object ID
enterprises.8164.1.16.5 Description
The total number of home agent deregistrations. Syntax
Counter32 Access
Read-only
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 69
Object starHACurActive
Object ID
enterprises.8164.1.16.6 Description
The current number of active home agent sessions. Syntax
Gauge32 Access
Read-only
starentMIB(8164).starentMIBObjects(1).starentFAMgr(17)
Object
starFAMgrCount
Object ID enterprises.8164.1.17.1
Description
The total number of foreign agent manager instances. Syntax
Gauge32 Access
Read-only
Object starFATtlArrived
Object ID enterprises.8164.1.17.2
Description
The total number of foreign agent session requests. Syntax
Counter32 Access
Read-only
Object starFATtlRejected
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
70 OL-23912-02
Object ID
enterprises.8164.1.17.3 Description
The total number of rejected foreign agent sessions. Syntax
Counter32 Access
Read-only
Object starFATtlDemultiplexed
Object ID enterprises.8164.1.17.4
Description
The total number of demultiplexed foreign agent sessions.
Syntax
Counter32 Access
Read-only
Object starFATtlDereg
Object ID
enterprises.8164.1.17.5 Description
The total number of foreign agent deregistrations. Syntax
Counter32 Access
Read-only
Object starFACurActive
Object ID
enterprises.8164.1.17.6 Description
The current number of active foreign agent sessions. Syntax
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 71
Gauge32 Access
Read-only
starentMIB(8164).starentMIBObjects(1).starentService(18) The
objects in this table are not accessible via SNMP. They are
intended for use within traps.
Object
starServiceTable
Object ID
enterprises.8164.1.18.1 Description
A table containing information about all of the service
managers. Syntax
Sequence of StarSvcEntry Access
Not-accessible
Object starServiceEntry
Object ID
enterprises.8164.1.18.1.1 Description
Information about a particular service manager. Syntax
StarSvcEntry Access
Not-accessible Sequence
starServiceVpnID Index starServiceSvcID Index starServiceVpnName
starServiceServName starServiceSubLimit starServiceSubCurrent
starServiceType starServiceFAIpAddr
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
72 OL-23912-02
starServiceHAIpAddr
Object starServiceVpnId
Object ID enterprises.8164.1.18.1.1.1
Description
The internal identification of the VPN (context). Syntax
Gauge32 Access
Not-accessible
Object starServiceSvcID
Object ID enterprises.8164.1.18.1.1.2
Description
The internal identification of the service, unique to the
associated context. Syntax
Gauge32 Access
Not-accessible
Object starServiceVpnName
Object ID
enterprises.8164.1.18.1.1.3 Description
The name of the VPN (context). Syntax
DisplayString Access
Read-only
Object starServiceServName
Object ID
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 73
enterprises.8164.1.18.1.1.4 Description
The name of the service. Syntax
DisplayString Access
Read-only
Object starServiceSubLimit
Object ID
enterprises.8164.1.18.1.1.5 Description
The configured subscriber limit. Syntax
Unsigned32 Access
Read-only
Object starServiceSubCurrent
Object ID enterprises.8164.1.18.1.1.6
Description
Current subscriber limit. Syntax
Gauge32 Access
Read-only
Object starServiceType
Object ID enterprises.8164.1.18.1.1.7
Description
Service type. Syntax
INTEGER
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
74 OL-23912-02
Access
Read-only Enumeration
unknown(1) pdsn(2) ggsn(3) ha(4) fa(5) l2tpserver(6) lac(7)
lns(8) closedrp(9 ecs(10) cscf(11) ipsg(12) evdoreva(13) pdif(15)
asnpc(16) mipv6ha(17) phsgw(18) phspc(19) sgw(20) pgw(21) mag(22)
gprs(23) hsgw(24) sgsn(25) mme(26) pdg(27) standalonefa(28)
imsue(29) fng(30) pccpolicy(31) pccquota(32) pccaf(33)
Object
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 75
starServiceFAIpAddr
Object ID enterprises.8164.1.18.1.1.8
Description
The IP address for an FA service. Where unknown or not
applicable this will contain all zeroes.
Syntax IpAddress
Access
Read-only
Object
starServiceHAIpAddr
Object ID
enterprises.8164.1.18.1.1.9 Description
The IP address for an HA service. Where unknown or not
applicable this will contain all zeroes.
Syntax
IpAddress Access
Read-only
starentMIB(8164).starentMIBObjects(1).starentCLIMgr(19) The
objects in this table are not accessible via SNMP. They are
intended for use within traps.
Object starCLITable
Object ID
enterprises.8164.1.19.1 Description
A table containing information about all interactive CLI
sessions. Syntax
Sequence of StarSvcEntry Access
Not-accessible
Object
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
76 OL-23912-02
starCLIEntry
Object ID enterprises.8164.1.19.1.1
Description
Information about a particular CLI session. Syntax
StarSvcEntry Access
Not-accessible Sequence
starCLIID starCLIUsername starCLITtyname starCLIPrivs
starCLIType starCLIRemoteIpAddr starCLIContext
Object starCLIID
Object ID
enterprises.8164.1.19.1.1.1 Description
The internal identify of the CLI session. Syntax
Gauge32 Access
Not-accessible
Object starCLIUsername
Object ID enterprises.8164.1.19.1.1.2
Description
The name of the user logged into the CLI sessions or ‘unknown’
if not known. Syntax
DisplayString
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 77
Access
Read-only
Object
starCLITtyname
Object ID
enterprises.8164.1.19.1.1.3 Description
The name of the TTY device used for the CLI session. Syntax
DisplayString Access
Read-only
Object starCLIPrivs
Object ID
enterprises.8164.1.19.1.1.4 Description
The CLI session privilege level. Syntax
DisplayString Access
Read-only
Object starCLIType
Object ID enterprises.8164.1.19.1.1.5
Description
The CLI type; commandline(1) represents the normal interactive
command line; ftp(2) represents an incoming FTP session.
Syntax INTEGER
Access
Read-only Enumeration
unknown(0)
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
78 OL-23912-02
commandline(1) ftp(2)
Object starCLIRemoteIPAddr
Object ID enterprises.8164.1.19.1.1.6
Description
The remote IP address used to access this CLI session. Where
unknown or not applicable (such as access through a serial port)
this will be 0.
Syntax
IpAddress Access
Read-only
Object starCLIContext
Object ID
enterprises.8164.1.19.1.1.7 Description
The context (VPN) currently being viewed or managed by the CLI
session. Syntax
DisplayString Access
Read-only
starentMIB(8164).starentMIBObjects(1).starentTaskMgr(20) The
objects in this table are not accessible via SNMP. They are
intended for use within traps.
Object starTaskTable
Object ID
enterprises.8164.1.20.1 Description
A table containing information about all of the active tasks.
Syntax
Sequence of StarSvcEntry Access
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 79
Not-accessible
Object starTaskEntry
Object ID enterprises.8164.1.20.1.1
Description
Information about a particular task. Syntax
StarSvcEntry Access
Not-accessible Sequence
starTaskFacility Index starTaskInstance Index
starTaskFacilityName starTaskCard starTaskCPU
Object starTaskFacility
Object ID
enterprises.8164.1.20.1.1.1 Description
The internal identify of the facility. Syntax
Unsigned32 Access
Not-accessible
Object starTaskInstance
Object ID
enterprises.8164.1.20.1.1.2 Description
The unique internal instance identifier for the task without a
given facility. Syntax
Unsigned32
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
80 OL-23912-02
Access
Read-only
Object
starTaskFacilityName
Object ID
enterprises.8164.1.20.1.1.3 Description
The name of the facility the task is associated with. Syntax
DisplayString Access
Read-only
Object starTaskCard
Object ID
enterprises.8164.1.20.1.1.4 Description
The slot number of the card where the task is located.
Syntax
Unsigned32 Access
Read-only
Object starTaskCPU
Object ID enterprises.8164.1.20.1.1.5
Description
The CPU number where the task is running. Syntax
Unsigned32 Access
Read-only
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 81
starentMIB(8164).starentMIBObjects(1).starentPPP(21) Object
starPPPStatTable
Object ID
enterprises.8164.1.21.1 Description
A table containing PPP statistics. Syntax
Sequence of StarPPPStatEntry Access
Not-accessible
Object starPPPStatEntry
Object ID enterprises.8164.1.21.1.1
Description
The statistics for an individual entry for a PPP context and
service. Syntax
StarPPPStatEntry Access
Not-accessible Sequence
starPPPStatVpnID starPPPStatSvcID Index (Implied)
starPPPStatVpnName starPPPStatServName starPPPStatInit
starPPPStatReneg starPPPStatSuccess starPPPStatFailed
starPPPStatReleased starPPPStatReleasedLocal
starPPPStatReleasedRemote starPPPStatLcpFailMaxRetry
starPPPStatLcpFailOption
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
82 OL-23912-02
starPPPStatIpcpFailMaxRetry starPPPStatIpcpFailOption
starPPPStatCcpFail starPPPStatAuthFail starPPPStatLcpEntered
starPPPStatAuthEntered starPPPStatIpcpEntered starPPPStatRenegPdsn
starPPPStatRenegMobil starPPPStatRenegAddrMismatch
starPPPStatRenegOther starPPPStatChapAuthAttempt
starPPPStatPapAuthAttempt starPPPStatMSChapAuthAttempt
starPPPStatChapAuthFail starPPPStatPapAuthFail
starPPPStatMSChapAuthFail starPPPStatStacComp starPPPStatMppcComp
starPPPStatDeflComp starPPPStatFscErrs starPPPStatUnknProto
starPPPStatBadAddr starPPPStatBadCtrl starPPPStatVjComp
starPPPStatDiscLcpRemote starPPPStatDiscRpRemote
starPPPStatDiscAdmin starPPPStatDiscIdleTimeout
starPPPStatDiscAbsTimeout starPPPStatDiscPPPKeepalive
starPPPStatDiscNoResource starPPPStatDiscMisc
starPPPStatFailedReneg starPPPStatLcpFailUnknown
starPPPStatIpcpFailUnknown
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 83
starPPPStatAuthAbort starPPPStatLowerLayerDisc
starPPPStatLcpSuccess starPPPStatAuthSuccess
starPPPStatRenegLowerLayerHandoff starPPPStatRenegParamUpdate
starPPPStatChapAuthSuccess starPPPStatPapAuthSuccess
starPPPStatMSChapAuthSuccess starPPPStatChapAuthAbort
starPPPStatPapAuthAbort starPPPStatMSChapAuthAbort
starPPPStatSessSkipAuth starPPPStatNegComp
starPPPStatCCPNegFailComp starPPPStatDiscLocalLowerLayer
starPPPStatDiscAddFlowFail starPPPStatDiscMaxRetriesLCP
starPPPStatDiscMaxRetriesIPCP starPPPStatDiscMaxSetupTimer
starPPPStatDiscInvalidDestVpn starPPPStatDiscOptNegFailLCP
starPPPStatDiscOptNegFailIPCP arPPPStatDiscNoRemoteIpAddr
starPPPStatDiscCallTypeDetectFail starPPPStatDiscRemoteDiscUpLayer
starPPPStatDiscLongDuraTimeout starPPPStatDiscAuthFail
starPPPStatLCPEchoTotalReq starPPPStatLCPEchoReqResent
starPPPStatLCPEchoRepRecved starPPPStatLCPEchoReqTimeout
starPPPStatRecvErrBadCtrlField starPPPStatRecvErrBadPacketLen
starPPPStatRemoteTerm starPPPStatMiscFail
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
84 OL-23912-02
Object starPPPStatVpnID
Object ID
enterprises.8164.1.21.1.1.1 Description
The internal identification of the PPP VPN (context). Syntax
Gauge32 Access
Not-accessible
Object starPPPStatSvcID
Object ID enterprises.8164.1.21.1.1.2
Description
The service identification is made up from first 8 chars of
context name and first 8 chars of service name separated by
(:).
Syntax
StarShortID Access
Not-accessible
Object starPPPStatVpnName
Object ID
enterprises.8164.1.21.1.1.3 Description
The name of the PPP VPN (context). Syntax
DisplayString Access
Read-only
Object starPPPStatServName
Object ID
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 85
enterprises.8164.1.21.1.1.4 Description
The name of the PPP service. Syntax
DisplayString Access
Read-only
Object starPPPStatInit
Object ID
enterprises.8164.1.21.1.1.5 Description
The number of initialized PPP sessions for the associated VPN
service. Syntax
Counter32 Access
Read-only
Object starPPPStatReneg
Object ID enterprises.8164.1.21.1.1.6
Description
The number of PPP session renegotiations for the associated VPN
service. Syntax
Counter32 Access
Read-only
Object starPPPStatSuccess
Object ID enterprises.8164.1.21.1.1.7
Description
The number of PPP session negotiation successes for the
associated VPN service. Syntax
Counter32
-
Starent Chassis MIB ▀ MIB Textual Conventions
▄ Cisco ASR 5000 Series SNMP MIB Reference
86 OL-23912-02
Access
Read-only
Object
starPPPStatFailed
Object ID
enterprises.8164.1.21.1.1.8 Description
The number of PPP session negotiation failures for the
associated VPN service. Syntax
Counter32 Access
Read-only
Object starPPPStatReleased
Object ID
enterprises.8164.1.21.1.1.9 Description
The number of PPP sessions released for the associated VPN
service. Syntax
Counter32 Access
Read-only
Object starPPPStatReleasedLocal
Object ID enterprises.8164.1.21.1.1.10
Description
The number of PPP sessions where the release was initiated
locally for the associated VPN service.
Syntax Counter32
Access
Read-only
Object
starPPPStatReleasedRemote
-
Starent Chassis MIB MIB Textual Conventions ▀
Cisco ASR 5000 Series SNMP MIB Reference ▄ OL-23912-02 87
Object ID
enterprises.8164.1.21.1.1.11 Description
The number of PPP session where the release was initiated
remotely for the associated VPN service.
Syntax Counter32
Access
Read-only
Object starPPPStatLcpFailMaxRetry
Object ID enterprises.8164.1.21.1.1.12
Description
The number of PPP sessions which failed to bring up the link
control protocol due to excessive retries for the associated VPN
service.
Syntax
Counter32 Access
Read-only
Object starPPPStatLcpFailOption
Object ID
enterprises.8164.1.21.1.1.13 Description
The number of PPP sessions which failed to bring up the Link
Control Protocol (LCP) due to an invalid option being received for
the associated VPN service.
Syntax Counter32
Access
Read-only
Object starPPPStatIpcpFailMaxRetry
Object ID enterprises.8164.1.21.1.1.14
Description
-
Starent Chassis MIB ▀ MIB Textual Conventions
�