1 ciar.it • Recliner devices ideas in progress Ciar, Ciar, • Massage chairs devices • Linear and rotary actuation systems [email protected]Made in Italy s i n c e 1 9 7 9 C I A R 30 ideas in progress DOC.COD.: N480010096E Rev.Nr.: 1.0 Date: 12/05/2010
73
Embed
Ciar, ideas in progress - Seritcioglu · 1 ciar.it • Recliner devices ideas in progress Ciar, Ciar, • Massage chairs devices • Linear and rotary actuation systems [email protected]
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
• Duty cycle: 2 min. ON and 5 min.OFF• Maximum load push/pull: 6000N/5000N• Speed : from 2 to 30 mm/sec.• Stroke: from 26 to 568mm. pitch 1mm. (with Minimun mounting distance)• Possibility of pre-setting the actuator for the customer application, if requested.• Permanent magnet DC motor Low tension DC 24V. Ø 59mm.• Microswitch enclosure turnable In three positions (0°, 90° e 180°)• Low noise level• Colour: Black• Zinc plated tube Ø 25mm.• Spindle Ø 16mm.• Rear attachment turnable by 45° available width 6mm or 8mm.• Metal front attachment (available 6mm or 8mm) or plastic front attachment (available 6mm or 8mm)• Compatible with all Ciar supply units• Ambient temperature: from +10°C to +40°C• Weigth: 1750 gr.• IP protection: IP30
Optionals:
• Encoder• Third microswitch• Brake• Metal rings in pushing tube• Motor plastic housing
Family: Linear actuatorsLine: StiloSeries: LM35_03
Made in Italy
Technical characteristics:
• Duty cycle: 2 min. ON and 5 min.OFF• Maximum load push/pull: 6000N/5000N• Speed : from 2 to 30 mm/sec.• Stroke: from 26 to 568mm. pitch 1mm. (with Minimun mounting distance)• Possibility of pre-setting the actuator for the customer application, if requested.• Permanent magnet DC motor Low tension DC 24V. Ø 59mm.• Microswitch enclosure turnable In three positions (0°, 90° e 180°)• Low noise level• Colour: Black• Zinc plated tube Ø 25mm.• Spindle Ø 16mm.• Rear attachment turnable by 45° available width 6mm or 8mm.• Metal front attachment (available 6mm or 8mm) or plastic front attachment (available 6mm or 8mm)• Compatible with Ciar PS10 supply unit• Ambient temperature: from +10°C to +40°C• Weigth: 1750 gr.• IP protection: IP30• Connection of handcontrol and supply unit directly onto the actuator
• Duty cycle: 2 min. ON and 5 min.OFF• Maximum load push/pull: 6000N/5000N• Speed : from 2 to 30 mm/sec.• Stroke: from 26 to 496mm. pitch 1mm. (with Minimun mounting distance=122mm.)• Possibility of pre-setting the actuator for the customer application, if requested.• Permanent magnet DC motor Low tension DC 24V. Ø 59mm.• Low noise level• Colour: Black• Sliding nut in POM resin• Spindle Ø 16mm.• Rear attachment turnable by 45° available width 6mm or 8mm.• Metal front attachment (available 6mm or 8mm) or plastic front attachment (available 6mm or 8mm)• Compatible with all Ciar supply units• Ambient temperature: from +10°C to +40°C• Weigth: 1900 gr.• IP protection: IP30
Optionals:
• Encoder• Third microswitch• Brake• Motor plastic housing
• Duty cycle: 2 min. ON and 5 min.OFF• Maximum load push/pull: 6000N/5000N• Speed : from 2 to 30 mm/sec.• Stroke: from 26 to 496mm. pitch 1mm. (with Minimun mounting distance=122mm.)• Possibility of pre-setting the actuator for the customer application, if requested.• Permanent magnet DC motor Low tension DC 24V. Ø 59mm.• Low noise level• Colour: Black• Sliding nut in POM resin• Spindle Ø 16mm.• Rear attachment turnable by 45° available width 6mm or 8mm.• Metal front attachment (available 6mm or 8mm) or plastic front attachment (available 6mm or 8mm)• Compatible with Ciar PS10 supply unit• Ambient temperature: from +10°C to +40°C• Weigth: 1900 gr.• IP protection: IP30• Connection of handcontrol and supply unit directly onto the actuator
Optionals:
• Encoder
45° 90° - 45°
INC
hand-control
transformer box
Family: Linear actuatorsLine: StiloSeries: LM55_03
• Duty cycle: 2 min. ON and 5 min.OFF• Maximum load push/pull: 3000N/3000N• Speed : from 2 to 30 mm/sec.• Stroke: from 26 to 568mm. pitch 1mm. (with Minimun mounting distance)• Possibility of pre-setting the actuator for the customer application, if requested.• Permanent magnet DC motor Low tension DC 24V. Ø 43mm.• Microswitch enclosure turnable In 2 positions (0°, 90°)• Low noise level• Colour: Black• Zinc plated tube Ø 25mm.• Spindle Ø 16mm.• Rear attachment turnable by 90° available width 6mm or 8mm.• Metal front attachment (available 6mm) or plastic front attachment (available 6mm or 8mm)• Compatible with all Ciar supply units• Ambient temperature: from +10°C to +40°C• Peso: 1750 gr.• Third microswitch• IP protection: IP30
Optionals:
• Encoder• Third microswitch• Metal rings in pushing tube
0° 90°
with hole with metal rings
A0°
B90°
39
39
Rea
r atta
chm
ent
plastic front attachment
with slot with metal rings
metal front attachment with slot
Fron
t atta
chm
ent
Mic
rosw
itch
encl
osur
e po
sitio
nsA
ctua
tor v
iew
new
Cur
rent
(A)
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
Spee
d (m
m/s
)
Speed
Speed
Supply = 24Vdc stabilized (SAMAR) Screw = 1S d. 16mm Motor = D.43 24V 1S 4000rpm (031)
Supply = 24Vdc stabilized (SAMAR) Screw = 2S d. 16mm Motor = D.43 24V 1S 4000rpm (031) Supply = 24Vdc stabilized (SAMAR) Screw = 2S d. 16mm Motor = D.43 24V 2S 4000rpm (095)
Supply = 24Vdc stabilized (SAMAR) Screw = 1S d. 16mm Motor = D.43 24V 2S 4000rpm (095)
Supply = 24Vdc stabilized (SAMAR) Screw = 3S d. 16mm Motor = D.43 24V 2S 4000rpm (095) Supply = 24Vdc stabilized (SAMAR) Screw = 3S d. 16mm Motor = D.43 24V 1S 4000rpm (031)
• Duty cycle: 2 min. ON and 5 min.OFF• Maximum load push/pull: 6000N/5000N• Speed : from 2 to 30 mm/sec.• Stroke: from 30 to 500mm. pitch 1mm. (with Minimun mounting distance)• Possibility of pre-setting the actuator for the customer application, if requested.• Permanent magnet DC motor Low tension DC 24V. Ø 59mm.• 2 Adjustable microswitches• Low noise level• Colour: Black• Spindle Ø 16mm.• Rear attachment turnable by 90° available width 6mm or 8mm.• Compatible with all Ciar supply units• Ambient temperature: from +10°C to +40°C• Weigth: 1750 gr.• • Third microswitch• IP protection: IP30
Optionals:
• Encoder
0° 90°
Rea
r atta
chm
ent
Act
uato
r vie
w
Cur
rent
(A)
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
Spee
d (m
m/s
)
Speed
Speed
Supply = 24Vdc stabilized (SAMAR) Screw = 1S d. 16mm Motor = D.43 24V 1S 4000rpm (031)
Supply = 24Vdc stabilized (SAMAR) Screw = 2S d. 16mm Motor = D.43 24V 1S 4000rpm (031) Supply = 24Vdc stabilized (SAMAR) Screw = 2S d. 16mm Motor = D.43 24V 2S 4000rpm (095)
Supply = 24Vdc stabilized (SAMAR) Screw = 1S d. 16mm Motor = D.43 24V 2S 4000rpm (095)
Supply = 24Vdc stabilized (SAMAR) Screw = 3S d. 16mm Motor = D.43 24V 2S 4000rpm (095) Supply = 24Vdc stabilized (SAMAR) Screw = 3S d. 16mm Motor = D.43 24V 1S 4000rpm (031)
• Duty cycle: 2 min. ON and 5 min.OFF• Maximum load push/pull: 3000N/3000N• Speed : from 2 to 30 mm/sec.• Stroke: from 30 to 500mm. pitch 1mm.• Minimum mounting distance 140+stroke• Possibility of pre-setting the actuator for the customer application, if requested.• Permanent magnet DC motor Low tension DC 24V. Ø 59mm.• 2 Adjustable microswitches• Microswitch enclosure turnable In three positions (0°, 90° e 180°)• Low noise level• Colour: Black• Spindle Ø 16mm.• Rear attachment turnable by 90° available width 6mm or 8mm.• Compatible with all Ciar supply units• Ambient temperature: from +10°C to +40°C• Weigth: 1750 gr.• IP protection: IP30
Optionals:
• Encoder• Possibility of fixing the actuator using 3 M4 screws• Possibility of extra ball bearing• Motor plastic housing• Spindle Ø 20mm.
0°
A
90°N.F.
A B
Family: Linear actuatorsLine: NakedSeries: LM25_N
Made in Italy
Slid
ing
nut
ball
bear
ing
Rea
r atta
chm
ent
Act
uato
r vie
w
B
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
new
Cur
rent
(A)
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
Spee
d (m
m/s
)
Speed
Speed
Supply = 24Vdc stabilized (SAMAR) Screw = 1S d. 16mm Motor = D.43 24V 1S 4000rpm (031)
Supply = 24Vdc stabilized (SAMAR) Screw = 2S d. 16mm Motor = D.43 24V 1S 4000rpm (031) Supply = 24Vdc stabilized (SAMAR) Screw = 2S d. 16mm Motor = D.43 24V 2S 4000rpm (095)
Supply = 24Vdc stabilized (SAMAR) Screw = 1S d. 16mm Motor = D.43 24V 2S 4000rpm (095)
Supply = 24Vdc stabilized (SAMAR) Screw = 3S d. 16mm Motor = D.43 24V 2S 4000rpm (095) Supply = 24Vdc stabilized (SAMAR) Screw = 3S d. 16mm Motor = D.43 24V 1S 4000rpm (031)
• Duty cycle: 2 min. ON and 5 min.OFF• Maximum load push/pull: 6000N/5000N• Speed : from 2 to 30 mm/sec.• Stroke: from 30 to 500mm. pitch 1mm.• Minimum mounting distance 95+stroke• Possibility of pre-setting the actuator for the customer application, if requested.• Permanent magnet DC motor Low tension DC 24V. Ø 59mm.• 2 Adjustable microswitches• Low noise level• Colour: Black• Sliding nut in POM resin• Spindle Ø 16mm.• Rear attachment turnable by 45° available width 6mm or 8mm.• Compatible with all Ciar supply units• Ambient temperature: from +10°C to +40°C• Weigth: 1900 gr.• IP protection: IP30
• Duty cycle: 2 min. ON and 5 min.OFF• Maximum load push/pull: 6000N/5000N• Speed : from 2 to 30 mm/sec.• Stroke: from 30 to 500mm. pitch 1mm.• Minimum mounting distance 90+stroke (type A)• Possibility of pre-setting the actuator for the customer application, if requested.• Permanent magnet DC motor Low tension DC 24V. Ø 59mm.• Low noise level• Colour: Black• Sliding nut in POM resin• Spindle Ø 20mm.• Rear attachment turnable by 90° available width 6mm or 8mm.• Compatible with all Ciar supply units• Ambient temperature: from +10°C to +40°C• Weigth: 1900 gr.• IP protection: IP30
Optionals:• Encoder• Motor plastic housing• Possibility of fixing the actuator using 3 M6 screws• Possibility of extra ball bearing
Fields of use:Movement of light parts of armchairs, lifts, shutters, etc. and wherever reduced size is indispensable.
Main characteristics:Max. thrust 1000 N.Speed from 3 to 10 mm/sec (on the base of max.thrust).Length of standard stroke: between 0 and 300mm (special solutions can be taken into consideration on request).
Since a high number of configurations are available the loading diagrams (thrust, speed and absorbed current) or further technical details are not shown here but can be reque-sted directly at the technical department.
• Low voltage DC motor (24Vdc). • Very small size: Dia. max. 40 or 43 mm. .• Compatible with all Ciar supply and control systems.
Optionals:LS - Limit-switch for end of stroke
Ove
rall
dim
ensi
ons
Act
uato
r vie
w
29,4
15
126
30
18
10
20
10
44
35
15
36,5
Modello LM15 senza microinterruttoriType LM15 without limit-switch
Modello LM15 senza microinterruttoriType LM15 without limit-switch
open tube with hole
Front attachment
+ corsa178mmtubo aperto con foro
(attacco frontale)
open tube with hole (LS)
with fork (LS)
+ corsa
+ corsa
218mmtubo aperto con foro (LS)
con forca (LS)226mm
with fork + corsacon forca
195mm
10
6 8
20 25
O
Chiusura min. = corsa + 226
43
10
36 30
15 10
15 120 8
10 10corsa + 50
27
19
3240
OO
O
O
OO
O O
dal 1979
CIAR
30
Azienda certificata ISO 9001-2008
Description:Linear actuator type: Tubular cursor.
Fields of use:Relax and lift armchairs, mechanical lifts, adjustable tables, camper automation, shut-ters, etc.
Main characteristics:
Max. thrust 6000 N.Speed from 2 to 30 mm/sec (on the base of max. thrust).Length of standard stroke: between 0 and 248 mm (special solutions can be taken into consideration on request).
Since a high number of configurations are available, the loading diagrams (thrust, speed and absorbed current) or further technical details are not shown here but can be reque-sted directly from the technical department.
Low voltage DC motor (24 Vdc).Limit switches for end of stroke already built-in.Silent operation.Compatible with all Ciar supply and control systems.
Optionals
BB – Axial bearing for resistance to major thrusts.ENC - Encoder built into the motor with sensor type Hall effect,resolution = 8 pulses/rev.LS – Built-in limit switches for end of stroke.
Ove
rall
dim
ensi
ons
Modello LM40 senza microinterruttori
Modello LM40 con microinterruttori
67105
3815 10Minimun mounting distance
Distanza minima
Minimun mounting distance Distanza minima
63
36 30
133
42
20 63
10 10
8
8
6363 20
133
10
842
36 30
10
10567 38
15 10
8
15
38
Type LM40 without limit-switch
Type LM40 with limit-switch
open tube with hole
Front attachment
+ corsa118mmtubo aperto con foro
(attacco frontale)
open tube with hole (LS)
with fork (LS)
+ corsa
+ corsa
146mmtubo aperto con foro (LS)
con forca (LS)156mm
with fork + corsacon forca
140mm
O O
O
O O
OO
OO
O
OO
Family: Linear actuatorsLine: ClassicsSeries: LM40
Fields of use:Relax and lift armchairs, mechanical lifts, adjustable tables, camper automation, shut-ters, etc..
Main characteristics:
Max. thrust 6000 N.Speed from 2 to 30 mm/sec (on the base of max. thrust).Length of standard stroke: between 0 and 689 mm (special solutions can be taken into consideration on request).
Since a high number of configurations are available, the loading diagrams (thrust, speed and absorbed current) or further technical details are not shown here but can be reque-sted directly from the technical department.
Low voltage DC motor (24 Vdc).Compatible with all Ciar supply and control systems.
Optionals:
ENC - Encoder built into the motor with sensor type Hall effect,resolution = 8 pulses/rev.LS – Limit-switch for end of stroke.26
Fields of use:Relax and lift armchairs, mechanical lifts, adjustable tables, camper automation, shut-ters, etc.
Main characteristics:
Max. thrust 6000 NSpeed from 2 to 30 mm/sec (on the base of max. thrust).Length of standard stroke: between 0 and 370 mm (special solutions can be taken into consideration on request).
Since a high number of configurations are available, the loading diagrams (thrust, speed and absorbed current) or further technical details are not shown here but can be reque-sted directly from the technical department.
Low voltage DC motor (24 Vdc).Compatible with all Ciar supply and control systems.
Optionals:
ENC - Encoder built into the motor with sensor type Hall effect,resolution = 8 pulses/rev.LS – Limit-switch for end of stroke.
64O
26,5
27
171
29,2
38,5
103
14
48,3
30
O 18
O 10
15
O10
34,6
53,5
6 44,5 27
open tube with hole
Front attachment
+ corsa127mmtubo aperto con foro
(attacco frontale)
open tube with hole (LS)
with fork (LS)
+ corsa
+ corsa
145mmtubo aperto con foro (LS)
con forca (LS)164mm
with fork + corsacon forca
146mm
Minimun mounting distance Distanza minima
Family: Linear actuatorsLine: ViewSeries: LM75
Azienda certificata ISO 9001-2008
Ove
rall
dim
ensi
ons
Act
uato
r vie
w
Made in Italy
dal 1979
CIAR
30
Family: Rotative actuatorsLine: TMSeries: TM11
Made in Italy
Technical characteristics:
• Duty cycle: 2 min. ON and 5 min.OFF• Maximum torque: 20Nm• Speed : from 60 mm/sec.• Permanent magnet DC motor Low tension DC 24V. Ø 59mm.• Low noise level• Colour: Black• Compatible with all Ciar supply units• Ambient temperature: from +10°C to +40°C• Weigth: 1200 gr.• IP protection: IP30
• Supply voltage: 24 Vac 50/60 Hz.• Max voltage on handcontrol: 12 Vdc.• Output voltage: 24 Vdc.• Control board that can drive up to 1 external linear actuators
• Supply voltage: 24 Vac 50/60 Hz.• Max voltage on handcontrol: 12 Vdc.• Output voltage: 24 Vdc.• Control board that can drive up to 2 external linear actuators
Optionals:
• Electronic protection against overloads equipped with differentiated threshold for each actuator.• Available with battery• Outlet for external security switchS
• Supply voltage: 230/120 Vac 50/60 Hz. Other voltages on request.• Max voltage on handcontrol: 12 Vdc.• Output voltage: 24 Vdc.• Main transformer equipped with thermofuse (125°C).
Optionals:
• Electronic protection against overloads equipped with differentiated threshold for each actuator.• Control board that can drive up to 5 vibrators. • Outlet for heating pad.
NB: This supply unit can drive either motors or vibrators.
• Supply voltage: 100/240 Vac, 50/60 Hz• Max voltage on handcontrol: 12 Vdc.• Output voltage: 24 Vdc.• Control board that can drive up to 3 external linear actuators• Integrates a lamellar transformer with resettable thermal protection device
Optionals:
• Independent control of 3 the actuators via 3 handcontrols• May include two 9V batteries to use in case of interruption of main supply.
• Supply voltage: 100/240 Vac, 50/60 Hz• Max voltage on handcontrol: 12 Vdc.• Output voltage: 24 Vdc.• Control board that can drive up to 2 external linear actuators• Integrates a switching power supply• The power cord can be disconnected
Optionals:
• Independent control of two actuators via 2 handcontrols
Sup
ply
unit
view
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
Ove
rall
dim
ensi
ons
Family: ElectronicLine: Supply unitSeries: SURange: SU30Made in Italy
Main characteristics:
• Supply voltage: 24 Vac 50/60 Hz.• Max voltage on handcontrol: 12 Vdc.• Output voltage: 24 Vdc.• Supply through external transformer• Control board that can drive a 2-motor (MF40, MF80) 3-motor (MF400) or 4-motor (MF450) massage system with possibility of speed adjustment of Tapping and Kneading function, equipped with ISP-type programming (In Situ Programming). Can also be used on mechanisms with sliding contacts. Predisposed for key or graphic display handcontrol• Control board that can drive up to 3 external linear actuators
Optionals:
• Electronic protection against overloads equipped with differentiated threshold for each actuator.• Outlet for 1 vibrator• Outlet for Thermo pad with timer• Outlet for MP3 player• Outlet for calf massage• Integrated battery-charger
152
92
158
142
107
52
Ø 3,5
Sup
ply
unit
view
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
Ove
rall
dim
ensi
ons
Family: ElectronicLine: Supply unitSeries: SURange: SU40Made in Italy
Main characteristics:
• Supply unit with internal ring coil or lamellar transformer• Supply Voltage: 100/240 Vac 50/60 Hz• Max voltage on handcontrol: 12 Vdc• Output voltage: 24 Vdc• Control board that can drive a 2-motor (MF40, MF80) or 3-motor (MF400) massage system• Control board that can drive up to 3 external linear actuators
Optionals:
• Electronic protection against overloads equipped with differentiated threshold for each linear actuator• Control board that can drive up to 5 Vibrators• Outlet for heating pad• Outlet for calf massager
51
165mm. 90
96
Ø 2,5
Sup
ply
unit
view
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
Ove
rall
dim
ensi
ons
Made in Italy
Caratteristiche tecniche:
• Supply Voltage: 24 Vac 50/60 Hz. • Max voltage on handcontrol: 12 Vdc.• Output voltage: 24 Vdc.• Modular structure (can be directly connected to TB50 and TB60 transformers and BB50 battery-charger).• Control board that can drive 2 Heating pads• Control board that can drive 2 external linear actuators
Optionals:
• Electronic protection against overloads equipped with differentiated threshold for each linearactuator• Outlet for Heating pad• Outlet for Lumbar support• Outlet for external safety switch• Infrared control system
• Supply Voltage: 24 Vac 50/60 Hz• Max voltage on handcontrol: 12 Vdc.• Output voltage: 24 Vdc.• Modular structure (can be directly connected to TB50 and TB60 transformers and BB50 battery-charger).• Control board that can drive up to 4 external linear actuators.
Optionals:
• Electronic protection against overloads equipped with differentiated threshold for each actuator.• Outlet for Heating pad• Outlet for lumbar support• Outlet for external safety switch• Infrared control system• Outlet for 5 vibrators
• Switching supply unit• Supply voltage: 100-240 Vac 50-60 Hz.• Rated output current: 2A• Rated output voltage: 29 Vdc.• Electronic overload protection• Efficiency >85%• Standby power consumption: < 0,5W• Duty cycle: 2 min. ON / 5 min. OFF (Supply voltage 220-240 Vac) 1 min. ON / 8 min. OFF (Supply voltage 100-120Vac) Detachable main cord and output cable
• Switching supply unit• Supply voltage: 100-240 Vac 50-60 Hz.• Rated output current: 2A• Rated output voltage: 29 Vdc.• Electronic overload protection• Efficiency >85%• Standby power consumption: < 0,5W• Duty cycle: 2 min. ON / 5 min. OFF (Supply voltage 220-240 Vac) 1 min. ON / 8 min. OFF (Supply voltage 100-120Vac) Detachable main cord and output cable• With 2 battery 9V (emergency)
• Supply voltage: 230/120 Vac, 50/60 Hz• Outlet voltage: 20-25 Vac (possibility of double supply).• Power: 36VA-100VA. • Low power consumption in stand-by mode (<0.2 Watt).• Ring coil transformer integrated.• Low magnetic emission.• Small dimensions.• Available either with directly connected net cable or with IEC plug connection.• Modular structure (can be directly plugable on the supply units SU50, SU51 as well as on the battery charger BB50).
Tran
sfor
mer
box
vie
w
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
Ove
rall
dim
ensi
ons
Family: ElectronicLine: Transformer boxSeries: IntegratedRange: TB60Made in Italy
Main characteristics:
• Supply voltage: 230/120 Vac, 50/60 Hz• Outlet voltage: 20-25 Vac (possibility of double supply)• Power: 36-100 Va• Low power consumption in stand-by mode (<0.2 Watt)• For ring coil or lamellar transformer use• Low magnetic emission• Small dimensions
97
63 6115
6
Tran
sfor
mer
box
vie
w
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
Ove
rall
dim
ensi
ons
Handcontrols 2010
Made in Italy dal 1979
CIAR
30
Handcontrols
Handcontrol
Panel
DO
C.C
OD
.: N
4700
6002
6E
Rev
.Nr.:
1.0
Dat
e: 1
2/05
/201
0
Certified Quality System ISO 9001-2008
Family: ElectronicLine: HandcontrolSeries: HandcontrolRange: HCFMade in Italy
Main characteristics:
• Up to 15 keys available• Type of keys: preformed lexan. Possibility of having rear illuminated lexan with optical fibre. Possibility of integrating a touch sensor to activate the rear illumination automatically
• Telephone cable 4, 6, or 8 flat or partially spiralled poles
• Compatible with all supply units
• Max. voltage 12 Vdc
• Up to 8 luminous LED indicators
• A version for infrared supply unit is available (SU31, SU50 and 51), functioning with 2x 12V model 23A alkaline batteries integrated
• Telephone cable 4, 6, or 8 flat or partially spiralled poles
• Compatible with all supply units
• Max. voltage 12 Vdc
Han
dcon
trols
vie
w
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
Ove
rall
dim
ensi
ons
Family: ElectronicLine: HandcontrolSeries: HandcontrolRange: HCS1Made in Italy
59mm. 14
145
Technical characteristics:
• Independent or simultaneous control (combination) from 1 to 3 actuators• Control of a massage device from the Ciar range• Personalisable colours and printing:• Compact, ergonomic design• 4, 6 or 8 poles telephone cable, flat or spiral• Max voltage 5 Vdc.• Function indicator LEDs• Compatible with all of the Ciar control/supply units• Furniture parts• Relaxation and massage armchairs
Standard configurations:
• 2 keys (M1)• M2 or Combi• Massage
Han
dcon
trols
vie
w
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
Ove
rall
dim
ensi
ons
Family: ElectronicLine: HandcontrolSeries: HandcontrolRange: HCVMade in Italy
Main characteristics:
• Up to 15 keys available
• Type of key: button or preformed lexan
• Telephone cable 4, 6, or 8 flat or partially spiralled poles
• Compatible with all supply units
• Max. voltage 12 Vdc
• Up to 8 luminous LED indicators15
6mm
.
6320
Han
dcon
trols
vie
w
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
Ove
rall
dim
ensi
ons
Family: ElectronicLine: HandcontrolSeries: PanelRange: HTR1Made in Italy
Main characteristics:
• Hand control fixable to surfaces
• 4 keys available
• Type of key: button
• Telephone cable 4 or 6 flat or partially spiral led poles
• Compatible with all supply units
• Max. voltage 12 Vdc
121mm. 77
49,693,6
75
109,6
65,5
28,5
6,5
58,4
Han
dcon
trols
vie
w
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
Ove
rall
dim
ensi
ons
Family: ElectronicLine: HandcontrolSeries: PanelRange: HTS1Made in Italy
Main characteristics:
• Hand control fixable to surfaces
• Very small dimension
• 2 keys available
• Type of key: button
• Telephone cable 4 or 6 flat or partially spiralled poles
• Telephone cable 4, 6, or 8 flat or partially spiralled poles
• Compatible with all supply units
• Max. voltage 12 Vdc
Family: ElectronicLine: HandcontrolSeries: PanelRange: TP1Made in Italy
Main characteristics:
• Handcontrol for interior parts or coverings using touch sensing technology
• Indipendent control of 1 actuator (2 pads) or 2 actuators (4 pads)
• Applicable in a wide range of materials (marble, wood, textile, leather, plastic etc.) and several thickness
• 4 or 6 poles telephone cable, flat or spiral
• Applicable as presence sensor
• Max. voltage 20 Vdc
• Compatible with all of the Ciar control/supply units
Standard configuration:
• 2 pads panel control (M1)• 4 pads panel control (M2)
Field of use:
• Furniture parts• Relaxation and massage armchairs
Pads
Han
dcon
trols
vie
w
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
Family: ElectronicLine: HandcontrolSeries: PanelRange: TP2Made in Italy
Main characteristics:
• Handcontrol for interior parts or coverings using touch sensing technology
• Indipendent control of 1 actuator (2 pads) or 2 actuators (4 pads)
• Applicable in a wide range of materials (marble, wood, textile, leather, plastic etc.) and several thickness
• 4 or 6 poles telephone cable, flat or spiral
• Applicable as presence sensor
• Max. voltage 20 Vdc
• Compatible with all of the Ciar control/supply units
Standard configuration:
• 2 pads panel control (M1)• 4 pads panel control (M2)
Field of use:
• Furniture parts
• Relaxation and massage armchairs
Buttons
Han
dcon
trols
vie
w
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
Family: ElectronicLine: HandcontrolSeries: PanelRange: TP2Made in Italy
Main characteristics:
• Handcontrol for interior parts or coverings using touch sensing technology
• Indipendent control of 1 actuator (2 pads) or 2 actuators (4 pads)
• Applicable in a wide range of materials (marble, wood, textile, leather, plastic etc.) and several thickness
• 4 or 6 poles telephone cable, flat or spiral
• Applicable as presence sensor
• Max. voltage 20 Vdc
• Compatible with all of the Ciar control/supply units
Standard configuration:
• 2 pads panel control (M1)• 4 pads panel control (M2)
Field of use:
• Furniture parts
• Relaxation and massage armchairs
Buttons
Han
dcon
trols
vie
w
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
DO
C.C
OD
.: N
4700
6002
7E
Rev
.Nr.:
1.0
Dat
e: 1
2/05
/201
0
Accessories 2010
Made in Italy
Vibrators
VR55
Thermo TH
Headrest
VR40 HR00
Certified Quality System ISO 9001-2008
since 1979
CIAR
30
Family: AccessoriesLine: Comfort / ErgonomicSeries: ThermoRange: THMade in Italy
Main characteristics:
• They are heat producers mounted in simple pillows, suitable for everything, for a benefical effect in many parts of the body, such as the cervical area, the lumbar region and the lower limbs.
Ther
mo
view
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
Family: AccessoriesLine: Comfort / ErgonomicSeries: HeadrestRange: HR00Made in Italy
Main characteristics:
• Headrest adjustable in height and depth using handcontrol
• Device with 1 low voltage dc motor (24Vdc).
• Light weight, compact device
• Silent operation
• Supply voltage: 230/120 Vac, 50/60 Hz
• Compatible supply units: All Ciar supply units
Field of use: ideal for recliner seats in reading or TV position.
• Lift/relax armchair kit
• Optimal excursion to guarantee the best ergonomic position of the relaxing seat
28°±1
60
27
30
220
67
W min 200
H m
in 3
00
Hea
dres
t vie
w
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
Ove
rall
dim
ensi
ons
Family: AccessoriesLine: WellnessSeries: VibroRange: VR55Made in Italy
Main characteristics:
• Low voltage dc motor (12 or 24 Vdc)
• Motor diameter 55 mm.
• Plastic case
33
115
97
67
44
55
55
4x10
Vibr
ator
vie
w
since 1979
CIAR
30
Certified Quality System ISO 9001-2008
Ove
rall
dim
ensi
ons
Family: AccessoriesLine: WellnessSeries: VibroRange: VR40Made in Italy