LUBRICATION AND MAINTENANCE CONTENTS page page C H A S S IS A N D B O D Y C O MP O NE N T S . . . . .. . . 2 5 D R I V E T R A I N ........................... 2 0 ENGINE M A INTEN A NCE ................... 14 G ENERAL INF O RMATI O N .................. 1 J U MP ST A R T IN G , H O IST IN G A N D T O WIN G . . .. 9 M A IN T EN A NCE S C HE D ULES ..... . .......... 4 GENERAL INFORMATION INDEX page page Cla ssification of Lubricants . . . . . . . . . . . . . . . . . . . 1 Component s Requi rin g No Lubric ati on . . . . . . . . . . . 2 Fl ui d Capaci ti es . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Fuel Requir ements . . . . . . . . . . . . . . . . . . . . . . . . . 1 International Symbols . . . . . . . . . . . . . . . . . . . . . . . 1 In tr oduc ti on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Lubrication and Replacement Parts Recommendation . . . . . . . . . . . . . . . . . . . . . . . . . 2 INTRODUCTION L ub rica tio n an d mainte nance is div ide d into re- quired and recommended service tasks. The required se rvice t as ks must be co mp lete d to ve ri fy the e mis- sion co ntrols func ti on c o rr ec tl y . The recomm e nde d service tasks should be completed to maintain safety and durability. This info rma tio n will as sis t the se rvic e pe rso nne l in pro viding ma ximum pro te c tion fo r e ac h o wne r’s vehicle. Conditions c an vary with individual driving hab its. I t is necess ary to sc hedule maintenance as a ti me in- te rval as well as a distance interval. I t is the o wn er’s responsibility to determine the ap- plicable driving condition. Also to ha ve the vehicle se rvi ced ac co rdi ng to the maintenanc e schedule, and to pa y for the nec e ssary parts and l ab or. Addition al mainte nance an d lubrica tion info rma- tion is listed in the Owner’s Manual. I NT ERN A TION AL SYMBO LS Chr ysle r Corporati on uses i nternati o nal symbols to ide ntify engine compartment lubricant and fl uid in- sp e c ti o n and fil l loc ations (Fi g. 1) . FUE L REQ UIREMEN TS Al l g asoli ne e ng ines req uire the use of unle aded fuel to r educ e the pote nti ally harmful effe c ts of lead to the environment. Also unlead e d fue l is ne c e ss ary to pre ve nt damage to the catalytic co nve rt er/O2 sen- sor. The fuel must have a minimum octane rating of87 ba se d on the (R + M)/2 c alculation me thod . CAUTION: UNLEADED FUEL ONLY must be used in vehicles equipped with a catalyst emission control system. All vehicles have reminders printed on the instrument panel below the fuel gauge and on the fuel fi ller door. The vehicles also have fuel fi ller tubes that are specially designed to accept only the sma ll-diameter dispensing nozzles. It is ille gal to bypass the desig n of an unleaded fuel filler tube and contaminate the fuel system. CLA SSIF ICA TIONOF LUB RICAN TS L ubrica ting fluids and chassis lubricants are clas- sifi ed ac co rding to standards recommended by the: • Society of Automotive Engineers (SAE). • American Petroleum Institute (API). Fig. 1 International SymbolsLUB RIC A T IO N A N D MAIN T E N A N C E 0 - 1
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
• National L ubricating Grease I nstitute (NL GI).
ENGINE OIL
API CERTIFICATION MARK
For maximum engine protection during all driving
conditions, install an engine oil that contains the API
Certification Mark (Fig. 2). The AP I CertificationMark indicates that the oil is certified to meet the
most critical requirements establi shed by the manu-
facturer.
Conformance to AP I specifications is determined by
tests that measure the ability of an oil to control:
• Engine wear.
• Bearing corrosion.
• Sludge.
• Varnish.
• Oil thickening.
• Rust.
• Piston deposits.
SAE VISCOSITYGRADE
An SAE viscosity grade is used to specify viscosity
of engine oil. SAE 30 specifies a single viscosity en-
gine oil. Engine oils also have multiple viscosities.
The viscosity grade of an oil is an indicator of its
thickness or flow capability. The lower the number,
the better the flow. The second viscosity grade num-
ber (without a W suffix) is the warm/hot-temperature
viscosity. The viscosity increases with engine temper-
ature. With a single viscosity grade, the oil viscosity
is valid only for one narrow temperature range.
Above that temperature range the viscosity will de-crease, and below that range the viscosity will in-
crease.
An engine oil with an SAE 5W-30 viscosity grade
provides good flow capabil ity for fast cold-weather
engine start-ups. The viscosity will then increase
with engine temperature to provide good high-tem-
perature engine lubrication (Fig. 3).
GEAR LUBRICANTS
A dual grade is also used to specify the viscosity of
multi-purpose gear lubricants.
The API grade designation identifies gear lubri-cants in terms of recommended usage.
CHASSIS COMPONENT AND WHEEL BEARING
LUBRICANTS
The chassis and wheel bearing lubricants that arerecommended are i dentified by the NL GI Certifica-tion Symbol. The symbol contains a coded designa-
tion. This identifies the usage and quality of thelubricant.
The letter G within the symbol designates wheelbearing lubricant. T he letter L designates chassis l u-bricant. When the letters are combined, the lubricantcan be used for dual applications. Use only lubricantsthat display the NL GI Certification Symbol (Fig. 4).
LUBRICATIONAND REPLACEMENT PARTS
RECOMMENDATIONDakota trucks are engineered to provide many
years of dependable operati on. However, lubricationservice and maintenance are required for each vehi-cle. When necessary, MOPARbrand lubricants and
genuine replacement parts are highly recommended.Each MOPAR brand lubricant and replacement partis designed and to provide dependability and longservice life.
COMPONENTS REQUIRING NOLUBRICATION There are many components that should not be lu-
bricated. The components that should not be lubri-cated are:• Air pumps.• Generator bearings.• Br ake booster cylinder.
Fig. 2 The API Engine Oil Certification Mark
Fig. 3 Temperature/Engine Oil Viscosity
Fig. 4 NLGI Lubricant Container Certification/ Identification Symbol
• Clutch release bearings.• Distributors.• Drive belts.• Drive belt idler pulleys.• Dri ve shaft center bearings.• I dler arms.• Rubber bushings.•
Starter motor bearings.• Suspension strut bearings.• Rear spring shackle bolts.• Throttle control cables.• Throttle linkage ball joints.• Water pump bearings.
FLUID CAPACITIESFuel Tank Standard ................................................57 L (15 gal.)Optional .................................................83 L (22 gal.)Engine Oil W/Fi lter change2.5L ......................................................4.2 L (4.5 qts.)
3.9L ......................................................3.8 L (4.0 qts.)5.2L ......................................................4.8 L (5.0 qts.)Engine Oil W/O F ilter change2.5L ......................................................3.8 L (4.0 qts.)3.9L ......................................................3.3 L (3.5 qts.)5.2L ......................................................4.2 L (4.5 qts.)
Cooling System2.5L ....................................................9.27 L (9.8 qts.)3.9L ................................................13.25 L (14.0 qts.)5.2L ................................................13.53 L (14.3 qts.)Automatic TransmissionDry fill capacity.*42RH & 46RH ........................9.0-10.4 L (19-22 pts.)
*Depending on type and size of internal cooler,length and inside diameter of cooler li nes, or use of an auxil iary cooler, these figures may vary. Refer toGroup-21, Transmission for proper fluid fill proce-dure.
Manual Tr ansmissionNV3500................................................2.0 L (2.1 qts.)AX15.....................................................3.1 L (3.3 qts.)Transfer CaseNP231 ..................................................1.2 L (2.5 pts.)Fill to bottom of fill hole.Front AxleN5 W/7-1/4 in......................................1.4 L (3.0 pts.)
Rear Axle7-1/4 i n.................................................1.4 L (3.0 pts.)8-1/4 i n.................................................2.1 L (4.4 pts.)Power SteeringN1(2WD) ............................................0.81 L (1.7 pts.)N5(4WD) ............................................1.18 L (2.5 pts.)
proper service intervals for Dakota. Use the schedule
that best describes the conditions the vehicle is oper-
ated under. When mileage and time is listed, follow
the interval that occurs first.
Schedule-A lists all the scheduled maintenance tobe performed under normal operati ng conditions.
Schedule-B is a schedule for vehicles that are
usually operated under one or more of the following
conditions.
• Frequent short trip driving less than 5 miles (8
km).
• Frequent driving in dusty conditions.
• Trailer towing or heavy load hauling.
• Frequent long periods of engine idling.
• Sustained high speed operation.
• Desert operati on.
• Frequent starting and stopping.• Cold climate operation.
• Off road driving.
• Commercial service.
• Snow plow operation.
• More than half of vehicle operation occurs in
heavy city traffic during hot weather (above 90° F ).
AT EACH STOP FOR GASOLINE
• Check engine oil level and add as required.
• Check windshield washer solvent and add as re-
quired.
ONCE A MONTH • Check ti re pressure and look for unusual tire wear
or damage.
• Check flui d levels of coolant reservoir, brake mas-
ter cylinder, power steering and transmission. Add
fluid as required.
• Check all lights and other electri cal items for cor-
rect operati on.
• I nspect battery and clean and tighten terminals as
required.
AT EACH OIL CHANGE
•
I nspect exhaust system.• I nspect brake hoses.
• Rotate the tires at each oil change interval shown
on Schedule- A: (7,500 M iles) or every other interval
shown on Schedule-B (6,000 Mil es).
• Check engine coolant level, hoses, and clamps.
• I f your mileage is less than 7,500 miles (12 000
km) yearly, replace the engine oil filter at each oil
change.
• L ubricate 4x4 steering l inkage.
SCHEDULE-A
7,500 MILES (12 000KM) OR AT 6 MONTHS
• Change engine oil.
15,000 MILES (24 000KM) OR AT 12 MONTHS • Change engine oil.
• Replace engine oil fil ter.
• L ubricate steering linkage (4x2).
22,500 MILES (36 000KM) OR AT 18 MONTHS
• Change engine oil.
• I nspect brake linings.
• L ubricate front suspension ball joints.
• I nspect front wheel bearings, clean and repack if
required (4x2).
30,000 MILES (48 000KM) OR AT 24 MONTHS
• Change engine oil.• Replace engine oil fil ter.
• Replace air cleaner element.
• Replace spark plugs.
• I nspect drive belt tension, adjust as required (2.5
L ).• L ubricate steering linkage (4x2).
37,500 MILES (60 000KM) OR AT 30 MONTHS
• Change engine oil.• Drain and refill four wheel drive transfer casefluid.• Drain and refill manual transmission fluid (ModelAX-15 only).• Drain and refill automatic transmission fluid. Re-place filter and adjust bands.
45,000 MILES (72 000KM) OR AT 36 MONTHS
• Change engine oil.• Replace engine oil fil ter.• I nspect brake linings.• L ubricate front suspension ball joints.• L ubricate steering linkage (4x2).• I nspect front wheel bearings, clean and repack if required (4x2).•
Flush and replace engine coolant at 36 months, re-gardless of mileage.
52,500 MILES (84 000KM) OR AT 42 MONTHS
• Change engine oil.• Flush and replace engine coolant (if not done at 36months).
60,000 MILES (96 000KM) OR AT 48 MONTHS
• Change engine oil.• Replace engine oil fil ter.• Replace air cleaner element.• Replace distributor cap and r otor.
• Drain and refill automatic transmission fluid. Re-
place filter and adjust bands.
• Change rear axle fluid.
• Change front axle flui d (4x4).
• L ubricate steering l inkage.• L ubricate front suspension ball joints.
• I nspect brake linings.
15,000 MILES (24 000KM)
• Change engine oil.
• L ubricate steering l inkage.
• I nspect air cleaner element, replace as necessary.
18,000 MILES (29 000KM)
• Change engine oil.
• Replace engine oil fil ter.
• Drain and refill manual transmission fluid (Model
AX-15 only).• L ubricate steering l inkage.
21,000 MILES (34 000KM)
• Change engine oil.
• L ubricate steering l inkage.
• L ubricate front suspension ball joints.
• I nspect front wheel bearings, Clean and repack if
required (4x2).
24,000 MILES (38 000KM)
• Change engine oil.• Replace engine oil fil ter.• L ubricate front suspension ball joints.• L ubricate steering l inkage.• Drain and refill automatic transmission fluid. Re-place filter and adjust bands.• Change rear axle fluid.• Change front axle flui d (4x4).• I nspect brake linings.
27,000 MILES (43 000KM)
• Change engine oil.• L ubricate steering l inkage.
30,000 MILES (48 000KM)
• Change engine oil.• Replace engine oil fil ter.• L ubricate steering l inkage.• Replace spark plugs.• Replace air cleaner element.• I nspect P CV valve, replace as necessary.*• I nspect drive belt tension, adjust as required (2.5L ).
33,000 MILES (53 000KM)
• Change engine oil.• L ubricate steering l inkage.
36,000 MILES (58 000KM)
• Change engine oil.
• Replace engine oil fil ter.
• L ubricate steering l inkage.
• L ubricate front suspension ball joints.
• Drain and refill manual transmission fluid (Model
AX-15 only).
• Drain and refill automatic transmission fluid. Re-place filter and adjust bands.
• Change rear axle fluid.
• Change front axle fluid (4x4).
• Drain and refill transfer case fluid.
• I nspect brake linings.
39,000 MILES (62 000KM)
• Change engine oil.
• L ubricate steering l inkage.
42,000 MILES (67 000KM)
• Change engine oil.
• Replace engine oil fil ter.• L ubricate steering l inkage.
• I nspect front wheel bearings, Clean and repack if
required (4x2).
45,000 MILES (72 000KM)
• Change engine oil.
• L ubricate steering l inkage.
• I nspect air cleaner element, replace as necessary.
48,000 MILES (77 000KM)
• Change engine oil.
•
Replace engine oil fil ter.• L ubricate steering l inkage.
• L ubricate front suspension ball joints.
• Drain and refill automatic transmission fluid. Re-
place filter and adjust bands.
• Change rear axle fluid.
• Change front axle fluid (4x4).
• I nspect brake linings.
51,000 MILES (82 000KM)
• Change engine oil.
• L ubricate steering l inkage.
• Flush and replace engine coolant.
54,000 MILES (86 400KM)
• Change engine oil.
• Replace engine oil fil ter.
• L ubricate steering l inkage.
• Drain and refill manual transmission fluid (Model
• Clean and relubricate crankcase inlet air cleaner
(if equipped).
• Replace spark plugs.
• Drain and refill automatic transmission fluid. Re-place filter and adjust bands.
• Change rear axle fluid.
• Change front axle flui d (4x4).
• Replace air cleaner element.
• Replace distributor cap and rotor.
• Replace ignition cables.
• I nspect P CV valve, replace as necessary.*
• Adjust belt tension on non-automatic tensioning
drive belts.
• Replace drive belt (2.5 L ).
• Replace fuel filter. (2.5 L ).
•
I nspect brake linings.• L ubricate front suspension ball joints.
• I nspect front wheel bearings, Clean and repack if
required (4x2).
63,000 MILES (102 000KM)
• Change engine oil.
• L ubricate steering l inkage.
66,000 MILES (105 600KM)
• Change engine oil.
• Replace engine oil fil ter.
• L ubricate steering l inkage.
69,000 MILES (110 000KM)
• Change engine oil.
• L ubricate steering l inkage.
72,000 MILES (115 200KM)
• Change engine oil.
• Replace engine oil fil ter.
• L ubricate steering l inkage.
• Drain and refill manual transmission fluid (Model
AX-15 only).
• Drain and refill automatic transmission fluid. Re-
place filter and adjust bands.
• Change rear axle fluid.
• Change front axle flui d (4x4).
• Drain and refill transfer case fluid.
• I nspect brake linings.
• L ubricate front suspension ball joints.
75,000 MILES (120 000KM)
• Change engine oil.
• L ubricate steering l inkage.
• I nspect air cleaner element, replace as necessary.
78,000 MILES (125 000KM)
• Change engine oil.• Replace engine oil fil ter.• L ubricate steering l inkage.
81,000 MILES (130 000KM)
• Change engine oil.• L ubricate steering l inkage.• Flush and replace engine coolant.
84,000 MILES (134 400KM)
• Change engine oil.• Replace engine oil fil ter.• L ubricate front suspension ball joints.• L ubricate steering l inkage.• Drain and refill automatic transmission fluid. Re-place filter and adjust bands.• Change rear axle fluid.• Change front axle fluid (4x4).• I nspect brake linings.•
I nspect front wheel bearings, Clean and repack if required (4x2).
87,000 MILES (140 000KM)
• Change engine oil.• L ubricate steering l inkage.
90,000 MILES (144 000KM)
• Change engine oil.• Replace engine oil fil ter.• L ubricate steering l inkage.• Replace spark plugs.• Drain and refill manual transmission fluid (ModelAX-15 only).• Drain and refill automatic transmission fluid. Re-place filter and adjust bands.• Replace air cleaner element.• I nspect drive belt tension, adjust as required (2.5L ).• I nspect PCV valve, replace as necessary.*
93,000 MILES (149 000KM)
• Change engine oil.• L ubricate steering l inkage.
96,000 MILES (154 000KM)
• Change engine oil.• Replace engine oil fil ter.• L ubricate steering l inkage.• L ubricate front suspension ball joints.• Change rear axle fluid.• Change front axle fluid (4x4).• I nspect brake linings.• I nspect front wheel bearings, clean and repack if required (4x2).
99,000 MILES (158 400KM)
• Change engine oil.• L ubricate steering l inkage.
• Change engine oil.• Replace engine oil fil ter.• L ubricate steering l inkage.
105,000 MILES (168 000KM)
• Change engine oil.• L ubricate steering l inkage.• I nspect air cleaner element, replace as necessary.• I nspect front wheel bearings, clean and repack if required (4x2).
108,000 MILES (172 800KM)
• Change engine oil.• Replace engine oil fil ter.• L ubricate steering l inkage.• L ubricate front suspension ball joints.• Drain and refill manual transmission fluid (ModelAX-15 only).• Drain and refill automatic transmission fluid. Re-
place filter and adjust bands.• Change rear axle fluid.• Change front axle flui d (4x4).• Drain and refill transfer case fluid.• I nspect brake linings.
111,000 MILES (177 600KM)
• Change engine oil.• L ubricate steering l inkage.• Flush and replace engine coolant.
114,000 MILES (182 400KM)
• Change engine oil.• Replace engine oil fil ter.• L ubricate steering l inkage.
117,000 MILES (187 200KM)
• Change engine oil.
• L ubricate steering l inkage.
120,000 MILES (192 000KM)
• Change engine oil.
• Replace engine oil fil ter.
•
L ubricate steering l inkage.• L ubricate front suspension ball joints.
• Replace spark plugs.
• Drain and refill automatic transmission fluid. Re-
place filter and adjust bands.
• Change rear axle fluid.
• Change front axle fluid (4x4).
• I nspect brake linings.
• Replace air cleaner element.
• Replace distributor cap and r otor.
• Replace igniti on cables.
• I nspect PCV valve, replace as necessary.*
• Adjust belt tension of non-automatic tensioning
drive belts.
• Replace drive belt (2.5 L ).
• Replace fuel filter. Federal only (2.5 L ).
• Clean and relubricate crankcase inlet air cleaner
(if equipped).
* This maintenance is recommended by Chrysler to
the customer but it is not required to maintain war-
WARNING: DO NOT ATTEMPT TO PUSH OR TOW AVEHICLE TO START THE ENGINE. UNBURNEDFUEL COULD ENTER THE EXHAUST CATALYTICCONVERTER AND IGNITE AFTER THE ENGINE IS
STARTED. THIS COULD CAUSE THE CONVERTERTO OVERHEAT AND RUPTURE.
WARNING: REVIEW ALL SAFETY PRECAUTIONSAND WARNINGS IN GROUP 8A, BATTERY/START-
ING/CHARGING SYSTEMS DIAGNOSTICS.DO NOT JUMP START A FROZEN BATTERY, PER-
SONAL INJURY CAN RESULT.DO NOT JUMP START WHEN MAINTENANCE
FREE BATTERY INDICATOR DOT IS YELLOW ORBRIGHT COLOR.
DO NOT JUMP START A VEHICLE WHEN THEBATTERY FLUID IS BELOW THE TOP OF LEADPLATES.
DO NOT ALLOW JUMPER CABLE CLAMPS TOTOUCH EACH OTHER WHEN CONNECTED TO ABOOSTER SOURCE.
DO NOT USE OPEN FLAME NEAR BATTERY.
REMOVE METALLIC JEWELRY WORN ON HANDSOR WRISTS TO AVOID INJURY BY ACCIDENTALARCING OF BATTERY CURRENT.
WHEN USING A HIGH OUTPUT BOOSTING DE-
VICE, DO NOT ALLOW BATTERY VOLTAGE TO EX-CEED 16 VOLTS. REFER TO INSTRUCTIONSPROVIDED WITH DEVICE BEING USED.
CAUTION: When using another vehicle as abooster, do not allow vehicles to touch. Electricalsystems can be damaged on either vehicle.
TO JUMP START A DISABLED VEHICLE:
(1) Raise hood on disabled vehicle and visually in-spect engine compartment for:• Battery cable clamp condition, clean if necessary.• Frozen battery.• Yellow or bright color test indicator, i f equipped.• Low battery fluid level.• Generator drive belt condition and tension.
• Fuel fumes or leakage, correct if necessary.
CAUTION: If the cause of starting problem on dis-
abled vehicle is severe, damage to booster vehicle
charging system can result.
(2) When using another vehicle as a booster
source, turn off all accessori es, place gear selector in
park or neutral, set park brake and operate engine at1200 rpm.(3) On disabled vehicle, place gear selector in park
or neutral and set park brake. Turn off all accesso-ries.
(4) Connect jumper cables to booster battery. RE Dclamp to positive terminal (+). BL ACK clamp to neg-ative terminal (-) (Fig. 1). DO NOT allow clamps atopposite end of cables to touch, electrical arc will re-sult. Review all warnings i n this procedure.
(5) On disabled vehicle, connect RE D jumper cableclamp to positive (+) terminal. Connect BL ACK jumper cable clamp to engine ground as close to the
ground cable attaching point as possible (F ig. 1).
CAUTION: Do not crank starter motor on disabled
vehicle for more than 15 seconds, starter will over-heat and could fail.
(6) All ow battery in disabled vehicle to charge to atleast 12.4 volts (75% charge) before attempting to
start engine. I f engine does not start within 15 sec-
onds, stop cranking engine and all ow starter to cool
(15 min.), before cranking again.
DISCONNECT CABLECLAMPS AS FOLLOWS:
• Disconnect BL ACK cable clamp from engine
ground on disabled vehicle.
• When using a Booster vehicle, disconnect BL ACK cable clamp from battery negative terminal. Discon-
nect RE D cable clamp from battery positive terminal.
• Disconnect RE D cable clamp from battery positive
terminal on disabled vehicle.
PORTABLE STARTING UNIT
There are many types of portable starting units
available for starting engines. Follow the manufac-
turer’s instructions and observe the listed precau-
tions when involved in any engine startingprocedure.
HOISTING RECOMMENDATIONSRefer to the Owner’s M anual for emergency vehicle
li fting procedures.
FLOOR JACK
When properly positioned, a floor jack can be usedto lift a Dakota vehicle (Fig. 2). Support the vehiclein the raised position with jack stands at the frontand rear ends of the frame rails.
CAUTION: Do not attempt to lift a vehicle with afloor jack positioned under:
• An axle tube.
• A body side sill.
• A steeri ng l inkage component.
• A drive shaft.
• The engine or transmission oil pan.
• The fuel tank.
• A front suspension arm.
Use the correct frame rail lifting locations
only (Fig. 2).
HOIST
A vehicle can be lifted with:
• A single-post, frame-contact hoist.
• A twin-post, chassis hoist.
• A ramp-type, drive-on hoist.
When a frame-contact type hoist is used, ver-
ify that the lifting pads are positioned properly
(Fig. 2).
WARNING: THE HOISTING AND JACK LIFTING
POINTS PROVIDED ARE FOR A COMPLETE VEHI-
CLE. WHEN A CHASSIS OR DRIVETRAIN COMPO-
NENT IS REMOVED FROM A VEHICLE, THE
CENTER OF GRAVITY IS ALTERED MAKING SOME
HOISTING CONDITIONS UNSTABLE. PROPERLY
SUPPORT OR SECURE VEHICLE TO HOISTING DE-
VICE WHEN THESE CONDITIONS EXIST.
TOWINGRECOMMENDATIONSA vehicle equipped with SAE approved sling-type
towing equipment or a wheel-li ft towing device can
be used to tow all DAKOTA vehicles. When towing a
4WD vehicle, use tow doll ies under the opposite endof the vehicle. A vehicle with a flat-bed device can
also be used to transport a disabled vehicle (F ig. 3).
A wooden crossbeam may be required for proper
connection when using the sling-type, front-end tow-
ing method.
SAFETY PRECAUTIONS
The following safety precautions must be ob-
served when towing a vehicle.
• Secure loose and protruding parts.
• Always use a safety chain system that is indepen-
dent of the l ifting and towing equipment.
• Do not allow towing equipment to contact the dis-
abled vehicle’s fuel tank.
• Do not allow anyone under the disabled vehicle
while it is lifted by the towing device.
• Do not allow passengers to r ide in a vehicle being
towed.
• Always observe state and local laws regarding tow-
ing regulations.
• Do not tow a vehicle in a manner that could jeop-
ardize the safety of the operator, pedestrians or other
CAUTION: Wide open throttle operation in lowgears, before engine break-in period is complete,can damage engine.
After first starting a new engine, allow it to idle for15 seconds before shifting into a drive gear. Also:• Drive the vehicle at varying speeds less than 88km/h (55 mph) for the first 480 km (300 miles).• Avoid fast acceleration and sudden stops.• Do not drive at full-throttle for extended periods of time.• Do not drive at constant speeds.• Do not idle the engine excessively.
A special break-in engine oil is not required. T heoriginal engine oil installed is a high quality, energyconserving lubricant. Special break-in oils are not
recommended. These oils could interfere with thenormal piston ring seating process.
New engines tend to consume more fuel and oil un-til after the break-in period has ended.
ENGINE OIL
WARNING: NEW OR USED ENGINE OIL CAN BE IR-RITATING TO THE SKIN. AVOID PROLONGED ORREPEATED SKIN CONTACT WITH ENGINE OIL.CONTAMINANTS IN USED ENGINE OIL, CAUSED BY
INTERNAL COMBUSTION, CAN BE HAZARDOUS TOYOUR HEALTH. THOROUGHLY WASH EXPOSED
SKIN WITH SOAP AND WATER.DO NOT WASH SKIN WITH GASOLINE, DIESEL
FUEL, THINNER, OR SOLVENTS, HEALTH PROB-LEMS CAN RESULT.
DO NOT POLLUTE, DISPOSE OF USED ENGINEOIL PROPERLY. CONTACT YOUR DEALER OR GOV-
ERNMENT AGENCY FOR LOCATION OF COLLEC-TION CENTER IN YOUR AREA.
ENGINE OIL SPECIFICATION
CAUTION: Do not use non-detergent or straight
mineral oil when adding or changing crankcase lu-
bricant. Engine failure can result.
The factory fill engine oil is a high quality, energy
conserving, crankcase l ubricant. The Recommended
SAE Viscosity Grades chart defines the viscosity
grades that must be used based on temperature in
the region where vehicle is operated (Fig. 1).
Chrysler Corporation recommends that Mopar mo-
tor oil , or equivalent, be used when adding or chang-
ing crankcase lubricant. The API Certification M ark
(Fig. 2) on the container indicates that the oil is cer-
tified to meet the most critical requirements estab-
lished by the manufacturer. Use engine oil which
contain the API Certification M ark.
ENGINE OIL ADDITIVES
Chrysler Corporation recommends that Mopar En-
gine Oil Supplement or equivalent be used when fric-
tion and corrosion reducing materials added to the
The engine oil level indicator is located at the fol-
lowing locations:
• 2.5L engine: at the left side of the cylinder head
between the distributor and the thermostat housing
• 3.9L and 5.2L engines: at the right front of the en-
gine (Fig. 3).
CRANKCASE OIL LEVEL INSPECTION
CAUTION: Do not overfill crankcase with engine oil,
oil foaming and oil pressure loss can result.
I nspect engine oil level approximately every 800 ki-
lometers (500 miles). Unless the engine has exhibited
loss of oil pressure, run the engine for about fiveminutes before checking oil level. Checking engine oil
level on a cold engine is not accurate. To maintain proper lubrication of an engine, the
engine oil must be kept at an acceptable level. Theacceptable level is located above the ADD mark andin the SAFE range on the dipstick.
(1) Position vehicle on level surface.(2) With engine OFF, allow approximately ten min-
utes for oil to settle to bottom of crankcase, removeengine oil dipstick.
(3) Wipe dipstick clean.
(4) I nstall dipstick and verify it is seated in the tube.
(5) Remove dipstick, with handle held above the
tip, take oil level reading.
(6) Add oil only if level is below the ADD mark on
dipstick.
ENGINE OIL CHANGE AND FILTER REPLACEMENT
ENGINE OIL CHANGE
Change engine oil at mileage and time intervals
descri bed in Maintenance Schedules.
TOCHANGE ENGINEOIL
Run engine until achieving normal operating tem-
perature.
(1) Position the vehicle on a level surface and turn
engine off.
(2) Hoist and support vehicle on safety stands. Refer to
Hoisting and J acking Recommendations in this group.
(3) Remove oil fill cap.
(4) P lace a suitable drain pan under crankcase
drain.
(5) Remove drain plug from crankcase and allow
oil to drain into pan. I nspect drain plug threads for
stretching or other damage. Replace drain plug andgasket if damaged.
(6) I nstall drain plug in crankcase.(7) Lower vehicle and fill crankcase with specified
type and amount of engine oil described in this section.(8) I nstall oil fill cap.(9) Start engine and inspect for leaks.(10) Stop engine and inspect oil level.
FILTER SPECIFICATION
All engines are equipped with a high quality full-flow, throw-away type oil filter. The same type of fil-ter is recommended when the fil ter is changed.
OIL FILTER REMOVAL
(1) Position a drain pan under the oil filter.(2) Using a suitable oil filter wrench loosen filter
(Fig. 4).
(3) Rotate the oil fil ter counterclockwise to removeit from the cylinder block oil filter boss.
as hard starting, stalling and stumble. I f these prob-lems occur, use another brand of gasoli ne before con-
sidering servicing the vehicle.
GASOLINE/OXYGENATE BLENDS
Some fuel suppliers blend unleaded gasoline with
materials that contain oxygen such as alcohol, MTBE
and E TBE. The type and amount of oxygenate used
in the blend is important. T he following are generally
used in gasoline blends:
ETHANOL
Ethanol (Ethyl or Grain Alcohol) properly blended,
is used as a mixture of 10 percent ethanol and 90
percent gasoli ne. Gasoline with ethanol may be
used in your vehicle.
METHANOL
CAUTION: Do not use gasolines containing metha-
nol. Use of methanol/gasoline blends may result in
starting and driveability problems. In addition, dam-
age may be done to critical fuel system compo-
nents.
Methanol (Methyl or Wood Alcohol) is used i n a va-riety of concentrations blended with unleaded gaso-
line. You may encounter fuels containing 3 percent or
more methanol along with other alcohols called cosol-
vents.
Pr oblems that are the result of using methanol/gas-
oline blends are not the responsibility of Chrysler
Corporation. They may not be covered by the vehicle
warranty.
MTBE/ETBE
Gasoline and MTBE (Methyl Tertiary Butyl Ether)
blends are a mixture of unleaded gasoline and up to
15 percent MT BE. Gasoline and E TBE (Ethyl Ter-
tiary Butyl Ether) are blends of gasoline and up to
17 percent ETBE. Gasoline blended with MT BE or
ETBE may be used.
CLEAN AIR GASOLINE
Many gasolines are now being blended that con-
tri bute to cleaner air, especially in those areas of the
country where air pollution levels are high. These
new blends provide a cleaner burning fuel and some
are referred to as Reformulated Gasoline.
I n areas of the country where carbon monoxide lev-
els are high, gasolines are being treated with oxygen-
ated materials such as MTBE, ETBE and ethanol.
Chrysler Corporation supports these efforts toward
cleaner air and recommends the use of these gaso-
lines as they become available.
IGNITION CABLES, DISTRIBUTOR CAP ANDROTOR
Replace the igniti on cables, distributor cap, and ro-
tor at the time specified in the maintenance sched-
ule. Oil and grime should be cleaned from the
ignition cables and distributor cap to avoid possible
spark plug fouling. Mopar Foamy Engine Degreaser
or equivalent is recommended for cleaning the engine
compartment. F or proper service and diagnostic pro-
cedures refer to Gr oup 8D, I gnition System.
IGNITION TIMING
Test and adjust, if necessary, the timing at the timespecifi ed in the maintenance schedule. Refer to the
specifications on the engine Emission Control label
(located in the engine compartment). Refer to Group
8D, I gnition Systems and to Group 25, Emission Con-
trol Systems for additional service information.
SPARKPLUGSI gnition spark plugs should be replaced at the
mileage interval described in the L ubrication and
Maintenance Schedules. Refer to the General I nfor-
mation section of this group. F or proper service pro-
cedures refer to Gr oup 8D, I gnition Systems.
BATTERY
WARNING: WEAR SAFETY GLASSES, RUBBER
GLOVES AND PROTECTIVE CLOTHING WHEN HAN-DLING/SERVICING A BATTERY. THE BATTERYELECTROLYTE CONTAINS SULFURIC ACID ANDWILL CAUSE HARM IF IT CONTACTS SKIN, EYES
OR CLOTHING. IT WILL ALSO DAMAGE PAINTED(AS WELL AS UN-PAINTED) SURFACES OF A VEHI-CLE. IF SULFURIC ACID CONTACTS ANY OFTHESE, FLUSH IMMEDIATELY WITH LARGE
AMOUNTS OF WATER. IF SULFURIC ACID CON-TACTS SKIN OR EYES, GET IMMEDIATE MEDICALATTENTION. DO NOT SMOKE IN THE VICINITY OF ABATTERY. KEEP OPEN FLAMES AND SPARKS
AWAY FROM BATTERY FILLER CAPS BECAUSEEXPLOSIVE GAS IS ALWAYS PRESENT.
I nspect battery tray, hold down and terminal con-nections when other under hood service is performed.For proper diagnostic procedures refer to Group 8A,Battery/Starting/Charging System Diagnostics. F orservice and cleaning procedures refer to Group 8B,Battery/Starter Service.
Care should be taken when disposing a bat-tery after removal from a vehicle. Lead-acidbatteries are highly poisonous and, when indis-criminately disposed, could create a problemfor the environment. Contact the applicable lo-cal city or county government agency to deter-mine where automobile (lead-acid) batteries
can be properly disposed in the local area.
RUBBER/PLASTIC COMPONENTS
CAUTION: Plastic hoses or wire harness covers willmelt or deform when exposed to heat from exhaust
system or engine manifolds.Position plastic or rubber components away from
moving parts in engine compartment or under vehi-cle, or damage will result.
Do not allow rubber engine mounts or other com-ponents to become oil contaminated, repair causeof oil contamination and clean area.
All rubber and plastic components should be in-spected when engine compartment or under vehicleservice is performed. When evidence of deteriorationexists, replacement is required. To reduce deteriora-tion of rubber components, Chrysler Corporation rec-ommends Mopar Foamy Engine Degreaser orequivalent be used to clean engine compartment of oil and road grime.
EMISSION CONTROL SYSTEMI nspect all emission control components and hoses
when other under hood service is performed. Refer to
emission system Vacuum Hose L abel located on theinside of the hood in the engine compartment andGroup 25, E mission Control Systems for proper ser-vice procedures.
ENGINE MOUNTS
I nspect the rubber in the engine mounts for exces-sive wear. Slight wear at the ends will not affect thefunctioning of an engine mount. I f excessive enginemovement is detected, the engine mount(s) should bereplaced.
ACCESSORY DRIVE BELTI nspect and adjust drive belts at the interval de-
scribed in the L ubrication and Maintenance Sched-
ules. Refer to General I nformation section of this
group. For proper inspection and adjustment proce-
dures, see Group 7, Cooling System.
EXHAUSTSYSTEM The exhaust system should be inspected when un-
der vehicle service is performed or as specifi ed in the
L ubrication and Maintenance Schedules.
INSPECTION
When inspecting an exhaust system, inspect for
cracked or loose joints, stripped screw/bolt threads,
corrosion damage, and worn or broken hangers
(Slight cracking in rubber isolator or hanger is ac-
ceptable). Replace all components that are corr oded
or damaged. Do not attempt repair. Also, inspect for
the following obvious conditions and correct as neces-sary:
• Exhaust system l eaks, damage, misalignment.
• Contact with body panels metal or the frame.
• Catalytic converter bulging or excessive heat dam-
age.
CAUTION: A catalytic converter will become con-
taminated if leaded gasoline is burned in the en-
gine. If this occurs, the complete converter must be
replaced.
For proper service procedures see Group 11, Ex-
haust System and I ntake Manifold.
AIR-CONDITIONER COMPRESSOR The lubricant level in the air-conditioner compres-
sor should be checked if there are indications that oil
was lost. L oss of lubricating oil usually accompanies
a l oss of refrigerant.
For additional information involving the A/C sys-
tem, refer to Group 24, Heater And Air Conditioning.
CLUTCH AND BRAKE PEDAL BUSHINGSI f the clutch and brake pedal mechanism squeaks,
the pivot bushings should be lubricated (Fig. 1). Use
MOPAR Multi-P urpose Lubricant, or an equivalent.
CLUTCH MASTER CYLINDER
LEVEL INSPECTION
WARNING: DO NOT ALLOW PETROLEUM OR WA-
TER BASE LIQUIDS TO CONTAMINATE CLUTCH
FLUID, SEAL DAMAGE AND CLUTCH FAILURE CAN
RESULT.
The clutch reservoir level should be inspected when
other underhood service is performed. (Fig. 2)
The fluid level is determined by its height in rela-
tion to the l evel indicator ring (Fig. 3) located inside
the reservoir. Add fluid until the height i s l evel with
the indicator ring.FLUID SPECIFICATION
Use M opar, Brake And Hydraulic Clutch Fl uid orequivalent. Use only brake fluid conforming to DOT3, Federal, Department of Transportation specifi ca-tion. To avoid fluid contamination, use fluid from aproperl y sealed container.
from an unsealed container. In addition, do not use
fluid from a container that has been opened and al-
lowed to stand for an extended length of time.
Moisture in the air can be absorbed by the fluid,
which causes dilution with loss of effectiveness.
CAUTION: Do not overfill - Because reservoir fluid
level rises as normal clutch wear occurs, overfilling
can cause clutch release problems. A low fluid level
may indicate a leak, in which case, hydraulic clutch
linkage replacement may be required.
CAUTION: Do not allow any petroleum base fluids
to contaminate the clutch hydraulic system. Seal
damage will result.
MANUAL TRANSMISSION The manual transmission should be inspected for
oil leaks and proper oil level when other under vehi-
cle service is performed.
LUBRICANT SPECIFICATION
When i t becomes necessary to add to or change the
lube oil in a Dakota manual transmission, use the
following lubricant:• AX-15—SAE 75W-90, API Quality Grade GL-5gear lubricant (MOPAR P/N 4649264).• NV3500—MOPAR Manual Trans. L ubricant (P/N4761526).
LUBRICANT LEVEL
The fill-hole plug for the AX-15 manual transmis-sions is located on the left side of the case (Fig. 4)and the fill-hole plug for the NV3500 manual trans-missions is located on the right side of the case (Fig.5). Determine the lubricant level according to the fol-lowing procedure.
(1) Remove the fill-hole plug (Fig. 3 or 4 ) from the
transmission. The lube oil should be within 1/4 inch
of the bottom edge of the fill hole.
If the transmission is warm, lube oil could
drip out of the fill hole. This is acceptable but
the lube oil should not gush out of the fill hole.
(2) I f not acceptable, raise the lube oil level to the
bottom edge of the transmission fil l hole.
Add lube oil in small amounts to raise the
level.(3) I nstall the fill -hole plug in the transmission.
LUBE OIL CHANGE
When it becomes necessary to change manual
transmission lube oil, use the following procedure.
(1) Raise and support the vehicle.
(2) Remove the fill-hole plug from the transmis-
sion.
(3) Pl ace a container to collect the lube oil under
the transmission drain-hole plug.
(4) Remove the drain-hole plug and drain the lube
oil from the transmission into the container.
Care should be exercised when disposing
used lube oil after it has been drained from atransmission.
(5) I nstall the drain-hole plug i n the transmission.(6) Fill the transmission until the lube oil begins to
drip out of the fill hole.(7) I nstall the fill -hole plug in the transmission.(8) Remove the support and l ower the vehicle.
SPECIAL ADDITIVES
Do not add any additives to a transmission otherthan B lack L ight detection dye.Fig. 4 AX-15 Manual Transmission Fill Plug
AUTOMATIC TRANSMISSION The automatic transmission fluid should be
changed and bands adjusted at the intervals de-
scribed in the M aintenance Schedules section of this
Group. The automatic transmission should be in-
spected for fluid leaks and proper fluid level when
other under hood service is performed. Refer to
Group 21, Transmission for proper service proce-dures.
CAUTION: To minimize fluid contamination, verify
that dipstick is seated in the fill tube after fluid level
reading is taken.
TO INSPECT THE TRANSMISSION FLUID
LEVEL
WARNING: USE EXTREME CAUTION WHEN THE
ENGINE IS OPERATING. DO NOT PUT YOUR
HANDS NEAR THE DRIVE BELT, PULLEYS OR FANBLADE. DO NOT STAND IN A DIRECT LINE WITH
THE FAN BLADE.
(1) Position the vehicle on a level surface.
(2) Start engine and allow to idle in PARK for at
least 60 seconds. The warmer the transmission fluid,
the more accurate the reading.
(3) While sitting in driver seat, apply brakes and
place gear selector in each position, then move the
selector to N (neutral).(4) Raise hood and remove transmission flui d level
indicator (dipstick) and wipe clean with a wipingcloth.
(5) I nstall dipstick and verify it is seated in fillhole or tube.
(6) Remove dipstick, with handle above tip, takeflui d level reading. I f the vehicle has been driven forat least 15 minutes before inspecting fluid level,transmission can be considered hot and readingshould be in the OK area. I f vehicle has run for lessthan 15 minutes and more than 60 seconds transmis-sion can be considered warm and reading should beabove MI N mark. Add fluid only if level is belowMI N mark on dipstick when transmission is warm
(Fig. 6).
CAUTION: Do not overfill automatic transmission,leakage or damage can result.
AUTOMATIC TRANSMISSION FLUID
SPECIFICATION
When it becomes necessary to add fluid (ATF) orwhen the ATF is replaced, use MOPAR ATF PL US(ATF Type 7176). Dexron I I I ATF can be used onlyif MOPAR ATF PL US (ATF Type 7176) is not avail-able.
FLUID AND FILTER CHANGE
The automatic transmission fluid and filter should
be changed at the intervals described in the M ainte-
nance Schedules section of this Group. Refer to
Group 21, Transmission for proper service proce-
dures.
TRANSFER CASE (4WD VEHICLES) The transfer case should be inspected for fluid
leaks and proper fluid l evel when other under vehicleservice is performed.
FLUID LEVEL
The transfer case fill hole plug is located at the
rear of the housing (Fi g. 7).
Determine the transfer case fluid (ATF ) level ac-
cording to the following procedure.(1) Raise and support the vehicle.
(2) Remove the fill hole plug from the transfer case
(Fig. 7). T he fluid (ATF ) level should be at the bottom
edge of the fill hole. T he level can be slightly below
the bottom edge of the fill hole if the fluid is cold.
(3) I f the l evel is not acceptable, raise the fluid
level to the bottom edge of the fill hole.
(4) I nstall the fill hole plug (Fig. 7). Tighten the fill
(3) Pl ace an appropriate container under the trans-
fer case drain hole plug (Fig. 7).(4) Remove the drain hole plug and drain the ATF
from the transfer case into the container.
CAUTION: Do not over-tighten the drain and fill hole
plugs. Over-tightening can strip the hole threads
and/or crack the aluminum housing.
(5) I nstall the drain hole plug in the transfer case.
Tighten the drain hole plug to 27 N⅐m (20 ft-lbs)torque.
(6) Fill the transfer case to the bottom edge of thefill hole.
(7) I nstall the fill hole plug in the transfer case Tighten the plug to 27 N⅐m (20 ft-lbs) torque.
(8) Remove the support and l ower the vehicle.
FLUID SPECIFICATION
I f it becomes necessary to add fluid (ATF ) to a Da-kota transfer case, use MOPAR ATF PL US or anequivalent Dexron I I I ATF.
FRONT AND REAR AXLES The front and rear axles do not require periodic
maintenance. I nspect the axles for oil leaks or dam-age and proper oil level when other under vehicle
service is performed. Oil leaks should be repaired be-fore returning vehicle to use. I f the oil appears milkyor foamy it is probably water contaminated. I f con-tamination is evident, change the axle lubricant. Re-fer to Group 2, Front Suspension and Axle or Group3, Rear Suspension and Axle (depending on applica-tion) for proper service procedures.
LUBRICANT SPECIFICATION
MOPAR Hypoid L ubricant, SAE 80W-90 or equiva-lent should be used in all Dakota axles.
I n addition, a friction additive (friction modifier)must also be used in a limited-slip differential.
LUBRICANT LEVEL
(1) Raise and support the vehicle.(2) The rear and front axles (4WD vehicles) differ-
ential housings have a rubber, PRE SS-IN type fillhole plug (Figs. 8 and 9). Pry the fill hole plug fromthe differential housing.
(3) The lubricant level should be within 10 mm(3/8 in.) of the bottom edge of the fill hole plug open-ing for rear axles. I t should be between 10 mm (3/8in.) and 13-mm (1/2-in.) below the bottom edge of thefil l hole plug opening for front axles (4WD vehicles).
(4) I f necessary, add lubricant to raise the level to
the acceptable position.
(5) I nstall the fill hole plug in the differential
housing.
DRIVESHAFTS
Lubricate at the intervals described in the Mainte-nance Schedule section of this Group. Refer to Group
16, Propeller Shafts for proper service procedures.
CAUTION: It is very important that drive shafts be
lubricated at periodic intervals and that the speci-
fied type of lubricant be used. Failure to properly
RUBBER AND PLASTIC HOSES/TUBING The condition of underbody rubber hose and plastic
tubing should be inspected whenever underbody ser-vice is performed.
Rubber hoses and plastic tubing should be re-placed immediately if there is any evidence of failure.
HOSE/TUBING INSPECTION
Vehicle operating conditions determine the useablelife of underbody hoses and tubing (Figs. 10 and 11).
These conditions include:• The extent and quality of vehicle maintenance.• The geographic area of vehicle operati on.• The length of exposure time to excess heat andchemical contaminants.
(1) I nspect all hose and tubing fittings for loose-ness and corrosion. I nspect the rubber hoses for brit-
tleness and cracks. Thoroughly inspect the hose ends
(those that are slipped over nipple connectors) for
splits.
(2) I nspect the surface of hoses and tubing for heat
and mechanical damage. Hose and tubing located
close to an exhaust pipe should be given special at-
tention.
(3) I nspect the rubber hose routing to ensure that
the hoses do not contact any heat source, moving
component, etc., that would potentially cause heat ormechanical damage.
(4) I nspect all the hose connections to ensure thatthey are secure and there is no fluid leakage. Actualdripping of hot fluid should be noted and the clampstightened in an attempt to stop the leakage before re-placing the hose.
Fig. 10 Front Axle Vacuum Shift Tubing—4WD Vehicles
(3) Replace the brake pads linings if they are worn
to within 0.78 mm (1/32 in) of the rivet head.
(4) Operate the rear brake self-adjuster lever and
pivot. Test the operation of the self-adjuster screw for
ease of movement.
(5) I nspect the self-adjuster components for wear
or damage.
(6) I nspect the disc brake caliper dust boot fordamage and indications of brake fluid leakage. I n-
spect the bushings and pins for corrosion, tears and a
binding condition.
(7) Pull the rear wheel cylinder dust boot back to
expose the wheel cylinder housing. I nspect for flui d
leaks. I nspect the pistons and cylinder bores.
(8) I nspect the brake differential warning valve
and housing for indications of leakage.
BRAKE FLUID HOSES/TUBING
The rubber brake fluid hoses should be inspected
for:
• Correct length
• Severe surface cracking
• Swelling
• Pulling
• Scuffing
• Excessively worn areas
If the hose has cracks or abrasions in the rub-
ber cover, the hose should be replaced.
(1) I nspect all the hoses for kinks, a distorted con-
dition and fluid leakage.
(2) I nspect the hose and tubing routing under the
vehicle. Verify that no hose/tubing is rubbing against
any exhaust or other underbody components.
PARKING BRAKE
(1) Engage the parki ng brake pedal and then re-
lease it.
(2) Test it for smooth operation and vehicle-holding
capability.
(3) I nspect the parking brake cables.
(4) With the parking brake released, the rear
wheels should rotate without restriction. Adjust the
parking brake cable tension, if necessary.
(5) Repair any parking brake malfunctions.
BRAKE OPERATIONAL TEST
(1) Drive the vehicle and test for proper brake ac-
tion.
(2) Note any indication of drum/rotor overheating.
(3) Evaluate any performance complaints received
from the owner/operator.
(4) Repair the brake system as necessary. Refer to
Group 5, Brakes for additional information and ser-
vice procedures.
TIRES The condition of the tires should be inspected. The
infl ation pressures tested/corrected at the same ti me
as the engine oil is changed and the oil filter is re-
placed.
The tires/wheels should be rotated at the i ntervals
described in the Maintenance Schedules section of
this Group.
INSPECTION
I nspect the tires for excessive wear, damage. Test
the tires for the recommended inflation pressure and
adjust the pressure accordingly. Refer to the tire in-
flation pressure decal located on the left door face.
Also to Group 22, Tires And Wheels for tire pressure
charts, tire replacement, and tread wear indicators.
ROTATION
Tires/wheels should be rotated according to the rec-
ommended interval. The first tire/wheel rotation is
the most important for establishing the prevention of
uneven tread wear. After rotation, adjust the tire in-
flation pressure to the air pressure recommended on
the decal located on the l eft door face.
Refer to Group 22, Tires And Wheels for the recom-
mended method of tire/wheel rotation.
BODY COMPONENTS
LUBRICATION REQUIREMENTS
All Dakota cab and cargo box operating mecha-
nisms and linkages should be lubricated when neces-
sary. The door weatherstrip seals should belubricated to prolong their life as well as to improve
door sealing.
LUBRICANT SPECIFICATIONS
All applicable exterior and interior vehicle operat-
ing mechanisms should be:
• I nspected
• Cleaned
• Pi vot/sliding contact areas on the mechanisms
should then be lubricated.Multi-purpose NL GI GC-L B MOPAR Multi-Mil eage
L ubricant or an equivalent, should be used to l ubri-cate the mechanisms. The door weatherstrip sealsshould be lubricated with silicone lubricant spray.Refer to the Body L ubricant Specifications chart be-low for additional lubricant applications.
LUBRICATION
(1) When necessary, lubricate the cab and cargobox operating mechanisms with the specifi ed lubri-cants.
(2) Apply silicone lubricant to a cloth and wipe i ton door seals to avoid over-spray that can soil pas-senger clothing.