86 www.ramset.com.au 1300 780 063 ChemSet ™ Reo502 ™ Extra Heavy Duty Anchoring Features & Benefits • Quick cure for improved productivity. • Sag resistant formula for horizontal holes • Bonds to carbide and diamond core drilled holes – strong bond • For Grade 500 reinforcing bar • Excellent electrical insulation properties T ypical Properti es Properties T ypical Value Appearance Part A: White Part B: Black Mixed: Light Grey Density 1.28 kg /litre @ 20°C Heat Distortion Temperatu re Approx. 80°C Hardness > Shore D 80 Compressive Strength (ASTM C579-01) 105 MPa Dielectric Constant 3.95 Conductivity 8 x 10 -11 ohmS/m Service Temperature Limits -10°C to 80°C Chemical Resistance See Technical Data Sheet Substrates Solid Concrete, Solid Stone (Proof loading recommended ), Solid BrickI n j e c t i o n A d h e s i v e s Description Extra heavy duty anchoring of reinforcing bar and threaded studs into solid concrete and stone.Two-component, high bond strength epoxy adhesive specially designed for structural connections, such as reinforcing bar. Suitable for dry, damp, wet and flooded holes. Quick setting for improved productivity . Long working time to reduce nozzle wastage. Bar development lengths in accordance with AS3600. Structural reinforcing bar connections in slabs, columns, beams and walls. Structural steel columns, raker angles, seating. T rades & Applications Key Features • Extra heavy duty epoxy • Quick 3 hour cure time • Dry, damp, wet and ooded holes • Suitable underwater • Long 20 minute working time for deep embedment Concreter Building Contractor Civil Contractor Steel Fabricator Balustrade Contractor Formworker Bricklayer Fitter Post-installing reinforcing bar 4 4 4 4 Starter bars 4 4 4 4 4 Threaded studs 4 4 4 4 4 Ta p valve to preserve contents Robust, puncture proof packaging Translucent cartridge to see remaining contents Extension for deep holes Made in Australia ISNE REO502J (750ml) Related Products DynaDrill ™ Carbide Drill Bits Diamond Motor Diamond Core Drill Bits V O C C o m p l i a n t Impact Wrench Wet/Dry Vacuum Hole Cleaning Brushes Hole Cleaning Pump
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Installation in Solid Concrete1. Drill or core hole to specified diameter and depth
2. Remove dust and debris by brushing and blowing 3 times each (If hole is wet
or flooded, brush only remove water and slurry with wet/dry vacuum)
3. Screw mixing nozzle onto cartridge and dispense 2-3 trigger pulls of adhesive
to waste until colour is light grey with no streaks
4. Insert tip of nozzle to bottom of hole and dispense adhesive
5. Fill hole to about 2/3 full
6. Insert threaded stud or reinforcing bar with rotating motion to release
trapped air
7. Wait until adhesive has fully cured before loading (see Working / Loading
Time chart below)
8. Clean up with acetone
Refer to Technical Data Sheet and MSDS available from
www.ramset.com.au, for precautions and further detailed
installation instructions
Working and Loading TimeSubstrate Temperature
(°C)
Gel Time
(min)
Cure Time
(hours)
10 21 8
16 18 5
20 20 3
27 12 2.5
32 8.5 2
I n j e c t i o n
A d h
e s i v e s
Recommended Installation TemperaturesMinimum Maximum
Substrate 5°C 40°C
Adhesive 20°C 32°C
ChemSet™ Reo 502™ - Indicative Working Loads in 32 MPa Concrete with ChemSet™
Anchor StudsThreadSize
Drilled HoleØ (mm)
Min HoleDepth (mm)
TighteningTorque (Nm)
Min EdgeDistance (mm)
Min AnchorSpacing (mm)
Max TensileLoad, Na (kN)
Max ShearLoad, V as
(kN)*
M8 10 80 10 35 50 6.3 4.4
M10 12 90 20 40 60 10.3 7.1
M12 14 110 40 50 75 15.3 10.5
M16 18 125 95 65 100 29.4 19.9
M20 24 150 180 80 120 37.9 29.9
M20 24 170 180 80 120 43.0 29.9
M24 26 160 315 100 145 40.9 43.3
M24 26 210 315 100 145 53.6 43.3
M30 32 270 600 120 180 72.4 90.4+
M36 38 330 1050 145 220 101.5 131.7+
Bold working load values in tension are limited by steel. All other values limited by concrete and adhesive bond
* For shear acting towards a concrete edge please contact a Ramset Engineer for further design assistance+ M30 and M36 steel shear values are for Grade 8.8 carbon steel. All other values are for Grade 5.8 carbon steel.
For water saturated or under water holes, reduce tensile load capacity by 30%
Hole ConditionHole Condition Suitable
Dry Yes
Damp Yes
Wet Yes
Flooded Yes
Drill Bit Type
Carbide Yes
Diamond Core Yes
Hole Orientation
Vertical Down Yes
Horizontal Yes
Vertical Up (Overhead) Contact Ramset™
ChemSet™ Reo 502™ Anchoring AdhesiveDescription Part No Box Quantity
Jumbo Cartridge (750 ml) + 1 Nozzle REO502J 12
ChemSet™ Universal Applicator CUA 1
ChemSet™ Pneumatic Universal Applicator CUAPN 1
Mixing Nozzles for Epoxy with Extension ISNE 5
Mixing Nozzle Turbo (Easier Dispensing) ISNET 1
Hole Cleaning Pump HCP 1
Hole Cleaning Pump High Volume HCPHV 1
Hole Cleaning Brush 13 mm HCBT13 1
Hole Cleaning Brush 20 mm HCBT20 1
Hole Cleaning Brush 26 mm HCBT26 1
Description Part No Box Quantity
The design engineer should ensure the structural element is capable of supporting these loads.
Refer to Ramset™ Specifiers Resource Book for more information or explanation of technical data.
Working load capacity was derived from characteristicultimate load capacity by applying the following factors: