Dept. Inorganic Chemistry, Fritz Haber Institute Characterization of porous solids and powders: Density, surface area and pore size Christian Hess 0. Motivation 1. Introduction 2. Gas adsorption 3. Density measurements 4. Adsorption isotherms 5. Surface area determination 6. Mesopore analysis Literature : Characterization of porous solids and powders, Lowell, Shields, Thomas, Thommes, Kluwer, Dordrecht, 2004.
34
Embed
Characterization of porous solids and powders: Density ... · Characterization of porous solids and powders: Density, surface area and pore size ... Characterization of porous solids
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Dept. Inorganic Chemistry, Fritz Haber Institute
Characterization of porous solids and powders:Density, surface area and pore size
Christian Hess
0. Motivation
1. Introduction
2. Gas adsorption
3. Density measurements
4. Adsorption isotherms
5. Surface area determination
6. Mesopore analysis
Literature: Characterization of porous solids and powders, Lowell, Shields, Thomas, Thommes, Kluwer, Dordrecht, 2004.
0. Motivation
1. Introduction
2. Gas adsorption
3. Density measurements
4. Adsorption isotherms
5. Surface area determination
6. Mesopore analysis
Literature: Characterization of porous solids and powders, Lowell, Shields, Thomas, Thommes, Kluwer, Dordrecht, 2004.
Catalysis: Nanostructured materials as support
• High(er) specific surface area of nanostructured materials � increased activity� formation of isolated, catalytic sites
…an estimate based on a material with spherical particles
using (1) S = 4 Π r2 / m
(2) m = 4/3 ρ Π r3
with ρ ~ 3 g/cm3 (typ. oxide value)
shows that for r = 1 cm _ S = 10-2 m2/gr = 1 µm _ S = 1 m2/gr = 1 nm _ S = 1000 m2/g
_ S = 3/ρr
_ Creation of high surface requires nanoscale structuring
Novel mesoporous silica molecular sieve: SBA-15
TEM characterization
100 nm
in a section of hexagonal poresalong a longitudinal section
_ Silica SBA-15 is a very ordered large-pore (7 nm) material
Model catalysts based on mesoporous SBA-15
• Support properties are well defined (structural homogeneity)and tunable (pore diameter)
� control over support properties� well-structured silica platform for vanadia catalysts
_ 3-D model catalyst for partial oxidation reactions
50 nm
20 nm VO x/SBA-15
silica
OH OH
OO
VOO
OH2O
silica
O
OV
OO
0. Motivation
1. Introduction
2. Gas adsorption
3. Density measurements
4. Adsorption isotherms
5. Surface area determination
6. Mesopore analysis
Literature: Characterization of porous solids and powders, Lowell, Shields, Thomas, Thommes, Kluwer, Dordrecht, 2004.
Real surfaces - Factors affecting surface area
• Idealization: cube → S = 6 l2
sphere → S = 4 π r2
Reality: Surface roughness due to voids, pores, steps, other imperfectionsand surface atomic and molecular orbitals
� real surface area > corresponding theoretical area
• Particle size: e.g. cube l = 1 m → S = 6 m2
l = 1 μm → S = 6 10-12 m2
N = 1018 → S = 6 106 m2
• Particle shape: e.g. two particles with same composition and mass Mcube = Msphere
(Vδ)cube = (Vδ)sphere
l3cube = 4/3 π r3
sphere
(Scube lcube)/6 = Ssphere rsphere/3
Scube/Ssphere = 2 rsphere / lcube
Factors affecting surface area
• Porosity: can overwhelm size and shape factors e.g. powder consisting of spherical particles
St = 4 π (r12 N1 + r2
2 N2 + … + ri2 Ni) = 4 π Σ ri
2 Ni
V = 4/3 π (r13 N1 + r2
3 N2 + … + ri3 Ni) = 4/3 π Σ ri
3 Ni
S = St/M = 3 Σ ri2 Ni/δ Σ ri
3 Ni
S = 3/δ rfor spheres of uniform radius:
with r ~ 3 g/cm3 (typ. oxide value):r = 1 cm → S = 10-2 m2/gr = 1 mm → S = 1 m2/gr = 1 nm → S = 1000 m2/g
0. Motivation
1. Introduction
2. Gas adsorption
3. Density measurements
4. Adsorption isotherms
5. Surface area determination
6. Mesopore analysis
Literature: Characterization of porous solids and powders, Lowell, Shields, Thomas, Thommes, Kluwer, Dordrecht, 2004.
Introduction
• most popular method for surface and pore size characterization (0.35-100nm)
other methods include: - small angle X-ray scattering (SAXS) - neutron scattering (SANS) - electron microscopy (scanning and transmission) - NMR methods- mercury porosimetry
• adsorption: enrichment of components in interfacial layergas adsorption → gas/solid interface
W = f (P,T,E)W: weight of gas adsorbed (per unit weigth adsorbent)E: interaction potential between adsorbate and adsorbent
T = const. → W = f (P,E)plot of W vs. P referred to as sorption isotherm
Physical adsorption forces
• Physical adsorption forces
van der Waals’ forces: dispersion forces, ion-dipole, ion-induced dipole dipole-dipole, quadrupole
• physisorption on a planar surface:London-van der Waals’ interaction energy:
• Experimentalmeasure nads vs P under static or quasi-equilibrium conditions using- volumetric (manometric) methods - gravimetric methods
Gravimetric method: based on sensitive microbalance and pressure gauge→ adsorbed amount measured directly (sensitivity ~ 10-8 g)→ adsorbent not in direct contact with thermostat (→ T control difficult!)
Volumetric method: based on calibrated volumes and pressure measurements → known amounts of gas are
admitted stepwise into cell→ Vads difference between gas
admitted and gas filling void volume→ requires manifold (Vm) and void
volume (Vv) to be accurately known
Experimental
→ Vm determination via expansion of He intocalibrated reference volume VR
→ Vv determination via expansion of He intosample cell volume occupied by adsorbent
m
Rm2
m
m1 )(T
VVPTVP +
=
m
vm4
m
m3 )(T
VVPTVP +
=
→ total volume of adsorptive dosed:PT
TPV
TVPV ×
−=
me
m
m
mmd
vdS VVV −=→ adsorbed volume:
)( vvdS αpVVVV +−=→ correction for non-ideality of real gases:α: non-ideality factore.g. N2: α = 6.6×10-5 torr-1(77K)
0. Motivation
1. Introduction
2. Gas adsorption
3. Density measurements
4. Adsorption isotherms
5. Surface area determination
6. Mesopore analysis
Literature: Characterization of porous solids and powders, Lowell, Shields, Thomas, Thommes, Kluwer, Dordrecht, 2004.
Introduction
→ contribution by pores/internal voids must be subtracted
• Density measurementse.g. for permeametry
volume specific surface area
true density =mass
volume occupied by mass
No porosity: true density measured by displacement of fluid→ accuracy: fluid volume determination
Porosity: fluid displaced by powder does not penetrate (all) pores→ apparent density < true density → true density via gas displacement (pycnometer)
using e.g. He (inert, small size)
Experimental
• sample cell:
aapca RTnVVP =− )(
apc RTnVVP 11 )( =−
• open valve 2:
aRaRpc RTnRTnVVVP +=+− 12 )(
RaVP
(2) in (3): RapcRpc VPVVPVVVP +−=+− )()( 12 (4)
(1)
(2)
(3)
)/(1)/(1
21
2
PPPPVVV a
Rcp −−
+=
0. Motivation
1. Introduction
2. Gas adsorption
3. Density measurements
4. Adsorption isotherms
5. Surface area determination
6. Mesopore analysis
Literature: Characterization of porous solids and powders, Lowell, Shields, Thomas, Thommes, Kluwer, Dordrecht, 2004.
Pore size and adsorption potential
nearly flat surface
• classification: macropore mesopore micropored > 50nm 2nm < d < 50nm d < 2nm
• at critical thickness lc:pore condensation (i.e. gas-like state → liquid-like state at μ < μ0)
Kelvin equation:aRT
VPP γ2)/ln( 0−
=
for complete wetting, i.e. θ = 0
Methodes based on modified Kelvin equation
→
- from isotherm: Vads/g catalyst as function of P/P0
τ)/( ma WWl =
• Calculation of the pore size distribution:
- Kelvin equ.: calulate a for θ=0 as function of P/P0
- calculate statistical film thickness l: lar −=p
- calculate a and rp in each decrement from successive entries- calculate Δl, the change in film thickness in successive steps - calculate ΔVads, the change ads. volume in successive steps - calculate ΔVliq, corresponding to ΔVads
- calculate ΔlΣS, the volume change of film remaining adsorbed - calculate the pore volume Vp:
- calculate the surface area S:p
p2rVS =
p2
pp lrV ⋅⋅= π[ ])(liq
2p
p SlVar
V Σ∆−∆
=
SllaV Σ∆+⋅⋅=∆ pliq π
Testing the modified Kelvin equation
• direct exp. test of Kelvin eq. (MCM, SBA) and comparison with XRD, TEM results→ Kelvin eq. underestimates pore size
• accurate pore size analysis by applyingmicroscopic models based on stat. mech.→ local fluid structure near curved wall→ capture properties of confined fluid
Adsorption vs desorption branch of hysteretic isotherm