4/24/2014 1 Chapter four Chapter four Laith Batarseh Laith Batarseh Axial load Home Next Previous End Axial load 4.1. Saint-Venant’s principle Assume that we apply axial load P to the gridded rectangular bar as shown in the figure. Assume also that the bar is under elastic deformation. As you can see, the deformation shown by the grid is not uniform. This means that the stress distribution is non uniform because of the relationship between the stress and strain (Hook’s law). We can study this irregular stress distribution by sectioning the bar from different locations as shown in the figure
24
Embed
Chapter four - Philadelphia University. axial... · Chapter four Laith Batarseh Axial load Home t us ... Axial load 4.2. elastic deformation of an axially loaded member ... Axial
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
It is obvious from the figure that as we move further from the
application point of the load, the stress distribution become more
uniform. In fact, there is a common distance from the point of load
appliance. This distance should be at least equal the largest dimension in
the cross-section area. For our case, this distance is the width of the bar.
After this distance, the stress distrubtion becomes uniform and we can
find the average stress using σavg = P/A.
You can also observe the none uniform deformation in the supporting
point.
This manner of behavior is called Saint-Venant’s principle.
4/24/2014
3
Axial load Axial load
4.2. elastic deformation of an axially loaded member 4.2. elastic deformation of an axially loaded member
Assume the following non uniform cross sectional member:
To find the stress, we take infinitesimal element dx
Axial load Axial load
4.2. elastic deformation of an axially loaded member 4.2. elastic deformation of an axially loaded member
As mentioned before, the stress and strain are related to this element
are found by using the next equation
Hook’s law states : σ = E.ε. Therefore:
dx
dδε
xA
xP and
L
ExA
dxxP
0
dx
dE
xA
xP
ExAdxxP
d Rearrange the previous equation:
Integrate to find δ:
4/24/2014
4
Axial load Axial load
4.2. elastic deformation of an axially loaded member 4.2. elastic deformation of an axially loaded member
According to the previous derivation, to find the total deformation in
axially loaded member, we use this equation
For a constant load (i.e. P(x) = P) and cross-section area (i.e. A(x) =A)
the deflection in the member can be found simply:
Where L is the total length of the member
L
ExA
dxxP
0
AE
PL
Axial load Axial load
4.2. elastic deformation of an axially loaded member 4.2. elastic deformation of an axially loaded member
When the member is subjected to several different axial loads (P)
AE
PL
The final thing is the sign convention. We can assume:
If the load and the elongation is tensile then the sign is positive
for both P and δ.
If the load and the elongation is compersion then the sign is
negative for both P and δ.
4/24/2014
5
4/24/2014
6
4/24/2014
7
4/24/2014
8
Axial load Axial load
4.3. principle of superposition 4.3. principle of superposition
It can be used to simply problems having complicated loadings. This is done by dividing the loading into components, then algebraically adding the results.
It is applicable provided the material obeys Hooke’s Law and the deformation is small.
If P = P1 + P2 and d ≈ d1 ≈ d2, then the deflection at location x is sum of two cases, δx = δx1 + δx2
Axial load Axial load
4.4. statically indeterminate axially loaded members 4.4. statically indeterminate axially loaded members
In some cases as the one shown in the figure, the number reaction unknowns is larger than the number of equilibrium equations. These cases are called statically indeterminate
In such cases, other equations are required to solve the unknowns. This condition is called compatibility or kinematic condition.
For example, in the case shown in the figure, the equilibrium vertical forces equation is
As you can see: one equation, two unknowns
0 PFF AB
4/24/2014
9
Axial load Axial load
4.4. statically indeterminate axially loaded members 4.4. statically indeterminate axially loaded members
to find other equation (i.e. compatibility condition), the total deflection is zero or: the deflection at A equal the –deflection at point B. mathematically,
The final equation is the 2nd equation to solve the two unknowns
AC
BCBA
BCBACABA
L
LFF
AE
LF
AE
LF
00
4/24/2014
10
4/24/2014
11
4/24/2014
12
Axial load Axial load
4.5. statically indeterminate: force method 4.5. statically indeterminate: force method
It is another way to solve statically indeterminate problem
Consider the statically indeterminate shown in fig.(a), the displacement
caused by the force P at point B is δp so the reaction (FB) must cause a
displacement δB equal to δp :
δp - δB =0
Axial load Axial load
4.5. statically indeterminate: force method 4.5. statically indeterminate: force method
Substitute the deflection formula
This is the 1st equation. The 2nd equation is derived from the
equilibrium condition
L
LPF
AE
LF
AE
PL ACB
BACBP 00
L
LPF
PFL
PLPFF
CBA
AAC
BA
00
4/24/2014
13
Axial load Axial load
4.6. thermal stresses 4.6. thermal stresses
When the temperature of a body changed: incerase or decrease, the
body will expand or contract according the change (or difference) in the
temperature.
The relation between the thermal deflection(δT) and temperature
difference (∆T) is given by:
δT = α.∆T.L
Where:
• δT is the thermal deflection
•α is the thermal expansion coefficient
•∆T the temperature change
•L is the length of the member
4/24/2014
14
Axial load Axial load
4.6. thermal stresses 4.6. thermal stresses
In the case of free members (i.e. one end is free to deflect), the thermal
deflection take place without generating stresses. These cases are the
statically determinate members.
If the member is restricted by supports (i.e. statically indeterminate),
the thermal deflection will cause thermal stresses which must be
When a material is stressed beyond the elastic range, it starts to yield and thereby causes permanent deformation. Among various inelastic behavior, the common cases exhibit elastoplastic or elastic-perfectly-plastic behavior.
4/24/2014
20
Axial load Axial load
4.9. residual stress 4.9. residual stress
After an axially loaded member is stressed beyond yield stress, it will create residual stress in the member when the loads are removed. Consider the stress history of a prismatic member made from an elastoplastic material. Path OA: Member is loaded to reach yield stress σY Path AC: Member deforms plastically Path CD: Unloading but permanent strain ε0 remains