Chapter 5 Steady-State Sinusoidal Analysis - TheCATweb.cecs.pdx.edu/~jmorris/ECE299/ECE299 lectures/Chapter 05 [Read... · 1 ELECTRICAL ENGINEERING: PRINCIPLES AND APPLICATIONS, Third

1

ELECTRICAL ENGINEERING: PRINCIPLES AND APPLICATIONS, Third Edition, by Allan R. Hambley, ©2005 Pearson Education, Inc.

Chapter 5Steady-State Sinusoidal Analysis


Chapter 5Steady-State Sinusoidal

Analysis 1. Identify the frequency, angular frequency,

peak value, rms value, and phase of a sinusoidal signal.

2. Solve steady-state ac circuits using phasors

and complex impedances.

2


4. Find Thévenin and Norton equivalent

circuits.

5. Determine load impedances for maximum power transfer.

6. Solve balanced three-phase circuits.

3. Compute power for steady-state ac circuits.


3


SINUSOIDAL CURRENTS AND VOLTAGES

Vm is the peak value

ω is the angular frequency in radians per second

θ is the phase angle

T is the period


Tπω 2

=

fπω 2=

( ) ( )90cossin −= zz

Frequency T

f 1=

Angular frequency

4


Root-Mean-Square Values

( )dttvT

VT

2

0rms

1∫=

RVP

2rms

avg =

( )dttiT

IT

2

0rms

1∫=

RIP 2rmsavg =


RMS Value of a Sinusoid

2rmsmVV =

The rms value for a sinusoid is the peak value divided by the square root of two. This is not true for other periodic waveforms such as square waves or triangular waves.

5



Phasor Definition

( ) ( )111 cos :function Time θtωVtv +=

111 :Phasor θV∠=V

6


Adding Sinusoids Using Phasors

Step 1: Determine the phasor for each term.

Step 2: Add the phasors using complex arithmetic.Step 3: Convert the sum to polar form.

Step 4: Write the result as a time function.


Using Phasors to Add Sinusoids( ) ( )45cos201 −= ttv ω

( ) ( )60cos102 += ttv ω

45201 −∠=V

30102 −∠=V

7


7.3997.2914.1906.23

5660.814.1414.1430104520

21s

−∠=

−=−+−=

−∠+−∠=

+=

jjj

VVV

( ) ( )7.39cos97.29 −= ttvs ω


8


Sinusoids can be visualized as the real-axis projection of vectors rotating in the complex plane. The phasor for a sinusoid is a snapshot of the corresponding rotating vector at t = 0.


Phase Relationships

To determine phase relationships from a phasor diagram, consider the phasors to rotate counterclockwise. Then when standing at afixed point, if V1 arrives first followed by V2after a rotation of θ , we say that V1 leads V2by θ . Alternatively, we could say that V2 lags V1 by θ . (Usually, we take θ as the smaller angle between the two phasors.)

9


To determine phase relationships between sinusoids from their plots versus time, find the shortest time interval tp between positive peaks of the two waveforms. Then, the phase angle isθ = (tp/T ) × 360°. If the peak of v1(t) occurs first, we say that v1(t) leads v2(t) or that v2(t)lags v1(t).


10



11


COMPLEX IMPEDANCES

LL Lj IV ×= ω

90∠== LLjZL ωω

LLL Z IV =


12



CCC Z IV =

90111−∠==−=

CCjCjZC ωωω

RR RIV =

13



Kirchhoff’s Laws in Phasor Form

We can apply KVL directly to phasors. The sum of the phasor voltages equals zero for any closed path.

The sum of the phasor currents entering a node must equal the sum of the phasor currents leaving.

14


Circuit Analysis Using Phasors and Impedances

1. Replace the time descriptions of the voltage

and current sources with the corresponding

phasors. (All of the sources must have the

same frequency.)


2. Replace inductances by their compleximpedances ZL = jωL. Replacecapacitances by their complex

impedances ZC = 1/(jωC). Resistances have

impedances equal to their resistances.3. Analyze the circuit using any of the

techniquesstudied earlier in Chapter 2, performing the calculations with complex arithmetic.

15



16



17



18



19



20



AC Power Calculations( )θcosrmsrmsIVP =

( )θcosPF =

iv θθθ −=

( )θsinrmsrmsIVQ =

21


rmsrmspower apparent IV=

( )2rmsrms22 IVQP =+

RIP 2rms=

XIQ 2rms=

RVP R

2rms=

XVQ X

2rms=


22



23



24



25



THÉVENIN EQUIVALENT CIRCUITS

26


The Thévenin voltage is equal to the open-circuit phasor voltage of the original circuit.

ocVV =t

We can find the Thévenin impedance by zeroing the independent sources and determining the impedance looking into the circuit terminals.


The Thévenin impedance equals the open-circuit voltage divided by the short-circuit current.

scsc

oc

IV

IV t

tZ ==

scII =n

27



28



29


Maximum Average Power Transfer

If the load can take on any complex value, maximum power transfer is attained for a load impedance equal to the complex conjugate of the Thévenin impedance.

If the load is required to be a pure resistance, maximum power transfer is attained for a load resistance equal to the magnitude of the Thévenin impedance.


30



BALANCED THREE-PHASE CIRCUITS

Much of the power used by business and industry is supplied by three-phase distribution systems. Plant engineers need to be familiar with three-phase power.

31



Phase Sequence

Three-phase sources can have either a positive or negative phase sequence.The direction of rotation of certain three-phase motors can be reversed by changing the phase sequence.

32



Wye–Wye ConnectionThree-phase sources and loads can be connected either in a wye configuration or in a delta configuration.

The key to understanding the various three-phaseconfigurations is a careful examination of the wye–wye circuit.

33



( ) ( )θcos3 rmsrmsavg LY IVtpP ==

( ) ( )θθ sin3sin2

3 rmsrms LYLY IVIVQ ==

34



35



36



YZZ 3=∆

37



Chapter 5 Steady-State Sinusoidal Analysis - TheCATweb.cecs.pdx.edu/~jmorris/ECE299/ECE299 lectures/Chapter 05 [Read... · 1 ELECTRICAL ENGINEERING: PRINCIPLES AND APPLICATIONS, Third

Documents