Chapter 18 Chapter 18 Chapter 18 Chemistry of the Chemistry of the Environment Environment
Dec 27, 2015
Chapter 18
Chapter 18Chapter 18Chemistry of the EnvironmentChemistry of the Environment
Chapter 18
IntroductionIntroduction
Human activities impact our environment.Economic growth depends of chemical processes
– e.g. clean water, energy usage, chemical synthesis, etc.
Earth Summit – Brazil 19921997 – Kyoto meeting2001 – Bonn – Signing of “Kyoto Protocols”
Protocols designed to internationally address environmental concerns and establish regulations.
2007 – UN meeting to establish further regulations and discuss monetary help for developing countries.
Chapter 18
TopicsTopicsEarth’s Atmosphere
– Ozone– Acid rain– Greenhouse effect
The OceanFreshwaterSoils and Weathering: A little basic
geochemistryGreen Chemistry
Find the topic interesting? Some easy reading…1. “An Introduction to Environmental Chemistry” by JE Andrews, P Brimblecombe, TD Jickells and PS Liss. 2. “A Short History of Nearly Everything” by Bill Bryson.3. Movie: An Inconvenient Truth
Chapter 18
Four regions.
Remember region and boundary names
Notice relationship between altitude and T and P.
(Colder in JNB than KNP AND why jets are pressurized.)
Earth’s AtmosphereEarth’s Atmosphere
Jets fly at this level.
Chapter 18
General InterestGeneral InterestThin clouds made of mixtures of ice, HNO3 and H2SO4 form in the upper atmosphere (stratosphere) over the poles when temperatures drop below -78°C (-109°F). Ozone depletion occurs in such polar stratospheric clouds.
Clouds from Earth’s surface to the stratosphere.
Aurora Borealis: collisions of charged particles above 80 km with O, O2, N, and N2.
Chapter 18
Earth’s atmosphere is affected by temperature and pressure and gravity.
Lighter molecules and atoms are found at higher altitudes. Less O2, air is “thinner”.
There is slow mixing of gases between regions in the atmosphere (important for ozone and pollution).
Troposphere and stratosphere account for 99.9% of the atmosphere’s mass, with about 75% of that in the troposphere.
Two major components of the atmosphere are nitrogen, N2, and oxygen, O2.
Earth’s AtmosphereEarth’s Atmosphere
Chapter 18
N2 has a triple bond (bond energy of 941kJ/mol)
O2 double bond (bond energy of 495kJ/mol)
Oxygen is more reactive than nitrogen.
Generally, oxides of non-metals form acidic solutions with water and oxides of metals form basic solutions in water.
A Note on NA Note on N22 and O and O22 Reactivity Reactivity
Chapter 18
Chapter 18
Parts Per MillionParts Per Million1 part per million (ppm) refers to 1 part in 1 million units of the whole. (One red pencil in a million yellow pencils)
If considering PV = nRT, volume fraction which is usually used for ppm can be interchanged with mole fraction.
So 1ppm = 1 mole in 1 million moles of total gas.
concentration in ppm = mole fraction x 106
Other common ppm designations: solids in mg kg-1, liquids in mg L-1, and most engineers use mg dm-3 (remember that 1L = 1dm3).
Chapter 18
Example Example
Calculate the concentration of methane in ppm if mole fraction = 0.000002.ppm = mole fraction x 106
= 0.000002 x 106 = 2 ppm
Calculate the concentration of xenon in ppb (parts per billion) if the mole fraction = 0.000000087.ppm = mole fraction x 106
ppb = mole fraction x 109
= 0.000000087 x 109 = 87 ppb
Chapter 18
Contains only a small percentage of the atmospheric mass. Low pressure!
Forms the outer defense against radiation and high-energy particles from space. (If Earth was the size of a desk globe, our atmosphere’s thickness would be ~ two layers of varnish. Very thin, but important, layer!)
Outer atmospheric reactions: photodissociation and photoionization
Outer Regions of the AtmosphereOuter Regions of the Atmosphere
Solar SpectrumSolar Spectrum
Chapter 18
Chapter 18
For photodissociation reactions to occur, photons must have sufficient energy to break the required bonds and the molecules must also absorb these photons.
Defn: the rupture of a chemical bond induced by radiation.
PhotodissociationPhotodissociation
hc
hE
Wave equation: The higher the frequency, the shorter the wavelength and the higher the energy of radiation.
Chapter 18
In the upper atmosphere (above 120km), photodissociation causes the formation of oxygen atoms:
O2(g) + h 2O(g)
Minimum energy required determined by the bond dissociation energy of O2 (495kJ/mol).
Dissociation of O2 is very extensive at high elevations:at 400km only 1% of oxygen is O2 while at 130km, about 50% is O2.
PhotodissociationPhotodissociation
Chapter 18
Defn: ionization of molecules (and atoms) caused by radiation.
1924: electrons discovered in the upper atmosphere. Therefore, cations must be present in the upper atmosphere (for charge balance).
Photoionization occurs when a molecule absorbs a photon of sufficient energy to remove an electron.
Wavelengths of light that cause photoionization and photodissociation are filtered by the atmosphere (occur more readily further from Earth).
PhotoionizationPhotoionization
Chapter 18
Ozone (O3) absorbs photons with a wavelength between 240 and 310 nm. (N2, O2 and O absorb wavelengths shorter than 240nm.)
Most of the ozone is present in the stratosphere, 12-50 km altitude. Maximum ozone concentration at an altitude of ~20 km.
Between 30-90km photodissociation of oxygen is possible:
O2(g) + h 2O(g)
Ozone and the Upper AtmosphereOzone and the Upper Atmosphere
Chapter 18
Oxygen atoms can collide with oxygen molecules to form ozone with excess energy, O3*:
O(g) + O2(g) O3*(g) (releases 105kJ/mol)
The excited ozone loses energy by decomposing to oxygen atoms and oxygen molecules (the reverse reaction) or by transferring the energy to M (usually N2 or O2):
O(g) + O2(g) O3*(g)
Ozone and the Upper AtmosphereOzone and the Upper Atmosphere
O3*(g) + M(g) O3(g) + M*(g)
Chapter 18
The formation of ozone in the atmosphere depends on the presence of O(g):
At low altitudes, most radiation with sufficient energy to form O(g) has been absorbed by upper atmosphere.
Release of energy from O3* depends on collisions, which generally occur at lower altitudes (more gas molecules).
Combining altitude and O(g) concentration means maximum ozone formation in the stratosphere.
Ozone and the StratosphereOzone and the Stratosphere
Chapter 18
A combination of photodissociation and photodecomposition reactions – makes and breaks ozone naturally.
O2(g) + hv O(g) + O(g)
O(g) + O2(g) O3(g) + M*(g) (heat released)
O3(g) + hv O2(g) + O(g)
O(g) + O(g) O2(g) (heat released)
O3 also formed by lightning strikes (can split O2) – can detect metallic smell of ozone during thunderstorms.
Ozone’s Natural CycleOzone’s Natural Cycle
Chapter 18
Crutzen 1970: naturally occurring nitrogen oxides catalytically destroy ozone. In 1974, Rowland and Molina showed that chlorine from chlorofluorocarbons (CFCs) deplete the ozone layer by catalyzing the formation of ClO and O2.
Ozone Depletion: CFCsOzone Depletion: CFCs
CFC CharacteristicsCFCl3 (Freon-11TM) and CF2Cl2 (Freon-12TM) used
as propellants in spray cans, as refrigerant gases, and foaming agents for plastics.
Unreactive in lower atmosphere, insoluble in water.
Diffuse slowly into stratosphere.Several million tons now present in the
atmosphere.
Chapter 18
In the stratosphere, CFCs undergo photodissociation of C-Cl:
CF2Cl2(g) + h CF2Cl(g) + Cl(g) (optimal at 30km)
Subsequently: Cl(g) + O3(g) ClO(g) + O2(g)
rate = k[Cl][O3], k = 7.2 109 M-
1s-1 at 298K
In addition, the ClO generated produces Cl as well:
2ClO(g) O2(g) + 2Cl(g)
The overall reaction: 2O3(g) 3O2(g).
CFC Depletion of OzoneCFC Depletion of Ozone
Think about this…
The rate at which ozone is destroyed increases with the amount of Cl, thus the greater the amount of CFCs that diffuse into the stratosphere, the faster the destruction of the ozone layer.
Chapter 18
1992: ~100 nations agreed to ban production and use of CFCs by 1996. October 1994: Ozone map in the Southern hemisphere showed a hole over Antarctica.
The Ozone Hole and CFC ReplacementsThe Ozone Hole and CFC Replacements
In 1995 the Nobel Prize for chemistry was awarded to F. Sherwood Rowland, Mario Molina, and Paul Crutzen for their studies of ozone depletion.
Replacement for CFCs are HFCs (e.g. CH2FCF3), where a C-H bond is broken instead of a C-Cl.
Chapter 18
Circulation of Earth’s atmosphere = “polar vortex” during Antarctic winter. Extreme cold (-80˚C) dissolves more gas.
Formation of polar stratospheric clouds (PSCs) (ice and acid). Dark for 3 months – allows reactants to build up.
Sept-Nov: sun returns and photochemical reactions go crazy!Estimated >50% of O3 in polar vortex destroyed.
PSCs break apart, O3-depleted stratosphere disperses and O3 can start rebuilding naturally.
Only an ozone “dimple” above Arctic pole (WHY?).
Antarctic OAntarctic O33 Hole: How it forms Hole: How it forms
Chapter 18
The troposphere consists mostly of O2 and N2 (~99%), but also CO, CO2, H2O, CH4, NOx, and SOx.
Even low to trace concentrations of other gases can have profound effects on the environment.
Most of these environmentally unfriendly gases are produced by the combustion of fossil fuels, industry and everyday life.
Down to Earth: Down to Earth: Chemistry of the TroposphereChemistry of the Troposphere
Chapter 18
Sulfur dioxide, SO2, is largely produced by the combustion of oil and coal and is a serious health hazard especially to people with respiratory difficulties.
SO2 is oxidized to SO3 by reacting with O2 or O3 which then reacts with water to produce sulfuric acid (acid rain):
SO3(g) + H2O(l) H2SO4(aq)
Note: nitrogen oxides also contribute to acid rain (nitric acid).
Normal rainwater has a pH of about 5.6 (due to dissolved H2CO3 from CO2 in the air).
Sulfur Compounds and Acid RainSulfur Compounds and Acid Rain
Chapter 18
Acid rain has a pH around 4 (pH of natural waters containing living organisms is 6.5 to 8.5). Natural waters with pH below 4 cannot sustain life.
Acid rain: corrosive to metals and stone building materials (will slowly dissolve limestone).
Too expensive to remove sulfur from oil and coal prior to its use. Therefore, the SO2 is removed from fuel upon combustion.
More than 30MT per year of SO2 are released into the atmosphere in the USA. Even more in developing countries.
Sulfur Compounds and Acid RainSulfur Compounds and Acid Rain
Chapter 18
Sulfur Removal from Coal CombustionSulfur Removal from Coal CombustionSO2 is commonly removed from fuel (oil and coal) as follows:
1. Powdered limestone decomposes into CaO which reacts with SO2 to form CaSO3 in a furnace.
2. CaSO3 and unreacted SO2 are passed into a scrubber (purification chamber) where the excess SO2 is converted to CaSO3 by jets of CaO.
3. CaSO3 is precipitated into a watery slurry.
Chapter 18
Produced by incomplete combustion of carbon-containing materials, e.g. fossil fuels.
About 1014 g of CO is produced in the United States per year (mostly from automobile exhaust).
CO binds irreversibly to the Fe in hemoglobin (about 210 times more strongly than oxygen).
Extremely dangerous and potentially fatal if inhaled in large quantities.
Carbon MonoxideCarbon Monoxide
Chapter 18
Photochemical smog (“the brown cloud”) is the result of photochemical reactions on pollutants.
In car engines, NO forms as follows:
In air, rapid oxidation of NO takes place:
At 393nm (sunlight), NO2 decomposes
NO2(g) + h NO(g) + O(g)
Nitrogen OxidesNitrogen Oxides
N2(g) + O2(g) 2NO(g) H = 180.8 kJ
2NO(g) + O2(g) 2NO2(g) H = -113.1 kJ
Chapter 18
The O produced by photodissociation of NO2 can react with O2 to form O3, which is the key component of smog.
O(g) + O2(g) O3(g) + M*(g)
Ozone is undesirable in the troposphere because it’s toxic and reactive.
Ozone problem…too much of it in smog, not enough in the stratosphere.
Nitrogen OxidesNitrogen Oxides
Chapter 18
Thermal balance between Earth and its surroundings.Ideally, radiation is emitted from Earth at the same rate as it is absorbed.
The troposphere is transparent to visible light (comes through), but not to IR radiation (heat).
Water Vapor, COWater Vapor, CO22, and Climate, and Climate
CO2 and H2O absorb IR radiation escaping from Earth’s surface at night keeping us warm. Called the Greenhouse Effect.
Chapter 18
Water Vapor, COWater Vapor, CO22, and IR Radiation, and IR Radiation
Chapter 18
Historical COHistorical CO22 Profile Profile
The carbon dioxide level on Earth has been increasing over the years.
Current CO2 levels = 380 ppm (a 35% increase from pre-industrial levels).www.physorg.com
Majority of the increase is from burning of fossil fuels.
Chapter 18
Between 2050 and 2100, the CO2 concentration is expected to double, possibly resulting in a global temperature increase of 1 to 3˚C.
International Energy Agency reports China will surpass US in CO2 emissions by 2009 (heavy reliance on coal).
NY Times, 7 Nov 2006
CO2 levels higher now than in the past 650,000 years based on comparision to tiny bubbles trapped in Antarctic ice cores.
25 Nov 2005, Science
Could result in melting of glaciers and a subsequent sea level rise.
No Quick Solution for CONo Quick Solution for CO22
Chapter 18
Increased COIncreased CO22 Implications Implications
Adapted from Gormitz and Lebedeff, 1967 by UNFCCC.
Submerged Florida peninsula (USA) shown with 1 meter sea level rise (in red). NASA
Glacial recession in Glacier National Park, Montana (USA). Wikipedia
Antarctic meltoff, 2005. NASA
Chapter 18
Methane: CHMethane: CH44
Of the three main greenhouse gases…receives least attention.
About 25x stronger than CO2 in greenhouse effect contribution!
Industrial age: increased from 0.3ppm to 1.8ppm.
Reactions: Stratosphere: oxidized – water byproduct.Troposphere: attacked – ozone byproduct.
Where it comes from: anaerobic bacterial processes, ruminant animals, volcanic activity.Australia – 14% country’s total greenhouse gas emissions from sheep and cows!!
Chapter 18
Chapter 18
• A rise in average global surface air temperature• Winters have become shorter by about 11 days• The earth’s ice cover is shrinking fast. Glaciers, polar icecaps, and polar sea ice are melting and disappearing at unprecedented rates due to global warming. •Warm water is killing much of the coral in ocean reefs and threatening sea life.• The mosquito-borne diseases have reached higher altitudes. Because of warmer temperatures, mosquitoes are now able to survive in regions where they formerly were not viable. • Rising sea levels are threatening to engulf Pacific islands.• Extreme weather is becoming more common.
Signs of global warming
Chapter 18
72% of Earth’s surface is covered with water.97.2% of Earth’s water is seawater, with a volume of 1.35 109 km3. Only 0.6% of Earth’s total water is in rivers, lakes, and groundwater!
Salinity: mass in grams of dry salts in 1 kg of seawater. Seawater salinity averages about 35.
Most elements in seawater are only present in small quantities (trace).
Commercially, NaCl, Br- and Mg2+ are obtained from seawater.
The World OceanThe World Ocean
Chapter 18
Chapter 18
Water used for drinking should contain less than 500 ppm dissolved salts (United States water regulation). Joburg water is at ~350 ppm.
Desalination: removal of salts from seawater.Common method: reverse osmosis (energy
intensive).– Osmosis: transport across a semipermeable
membrane, where solvent moves from dilute to concentrated.No good for desalination.
– Reverse osmosis: under applied pressure, solvent moves from more concentrated solution to more dilute solution.
DesalinationDesalination
Chapter 18
DesalinationDesalination
Seawater is introduced under pressure and water passes through the fiber walls and is separated from the ions.
Largest desalination plant in Saudi Arabia responsible for 50% of the country’s drinking water by reverse osmosis from Persian Gulf. Small scale reverse osmosis desalinators used for camping, traveling, and at sea.
Chapter 18
An adult needs about 2 L a day for drinking.The average person uses about 300 L of
freshwater per day.Industry uses about 105 L of water are used to
make enough steel for one car!
As water flows over the terrain it dissolves many substances.
Freshwater usually contains some ions (Na+, K+, Mg2+, Ca2+, Fe2+, Cl-, SO4
2-, and HCO3-) and
dissolved gases (O2, N2, and CO2).
FreshwaterFreshwater
Chapter 18
Water fully saturated with air at 1 atm and 20C has 9 ppm of O2 dissolved in it.
Cold water fish require about 5 ppm of dissolved oxygen for life.
Dissolved ODissolved O22 and Water Quality and Water Quality
Chapter 18
Aerobic bacteria require oxygen to biodegrade organic material, e.g., sewage, industrial waste from food-processing plants and paper mills, and effluent from meat packing plants.
Oxidize organic material into CO2, HCO3-, H2,
NO3-, SO4
2-, and phosphates.
Once the oxygen level has been depleted, aerobic bacteria cannot survive.
Anaerobic bacteria complete the decomposition process forming CH4, NH3, H2S, PH3, and other smelly products.
Bacterial Activity in GroundwaterBacterial Activity in Groundwater
Chapter 18
Municipal Water TreatmentMunicipal Water TreatmentThere are five steps
1.Coarse filtration. Occurs as water is taken up from lake, river or reservoir.2.Sedimentation.
Water is allowed to stand so that solid particles (e.g. sand) can settle out. Gelatinous precipitate of Al(OH)3 settles out slowly.
3.Sand Filtration. Filteration through a sand bed to remove Al(OH)3 and anything it trapped.
4.Aeration. Air oxidizes any organic material.
5.Sterilization. Chlorine used, forms HClO(aq) in solution which kills bacteria.
Chapter 18
Green Water PurificationGreen Water Purification
When Cl2(g) is used to treat water, some trihalomethanes (THM) are often produced, which can go undetected.
THMs (CHCl3, CHClBr2) are suspected carcinogens.
Ozone and ClO2 could be used as alternatives, but they are not completely safe.
Green water purification is an open problem.
Chapter 18
Hard water contains relatively high amounts of Ca2+, Mg2+ and other divalent cations. Unsuitable for most household and industrial uses.
-Forms insoluble soap scum and water “stains” Mineral deposits form when hard water is heatedCa2+(aq) + 2HCO3
-(aq) CaCO3(s) + CO2(g) + H2O(l)
Hard WaterHard Water
“scale”
Chapter 18
Water from underground sources with considerable contact with CaCO3 and other minerals containing Ca2+, Mg2+ and Fe3+ requires softening.
Lime-soda process used for large scale municipal water-softening operations. Water treated with lime, CaO (or slaked lime, Ca(OH)2), and soda ash, Na2CO3.
Ca2+(aq) + CO32-(aq) CaCO3(s)
Mg2+(aq) + 2OH-(aq) Mg(OH)2(s)
Water SofteningWater Softening
precipitates
Chapter 18
Ion exchange used for household water softening.
Hard water is passed through a bed of ion exchange resin: plastic beads with covalently bound anion groups (–COO- or –SO3
-). These anion groups have Na+ attached to counter their charges. The Ca2+ and other cations in the hard water are exchanged with the Na+.
2Na+(R-COO-)(s) + Ca2+(aq) Ca2+(R-COO-)2(s) + 2Na+(aq)
Water SofteningWater Softening
Chapter 18
Soils and WeatheringSoils and Weathering
Soils are complex, largely variable, made up of any number of inorganic and organic components, generally a product of mineral or rock weathering.
Weathering: physical and chemical processes• Water (good solvent for ions)• Oxidation reactions (most metals can change
oxidation state when exposed to the environment)• Freeze-thaw sequences
Chapter 18
ClaysClays
THESE are South African soils! Sheet silicates – continuous Si-O bonds in
tetrahedral shape. Each Si is partially + and each O is partially -.
Cations (+) in water interact with clays like ion exchange resins.
Si Si Si Si Si
O O O O+ + + +
SiSiSiSiSi
Si Si Si Si Si
O
O
O
O
O
O O
O+ + + +
1:1 clay“open-faced sandwich”Next sheet looks the same, just right on top.
2:1 clay“closed sandwich”Next sheet looks the same.
Chapter 18
ClaysClays
Cation exchange depends on:
1. Ionic Potential = charge / radiusmeasure of charge density on ion surface.
Consider Na+ vs Cs+. Both have charge = +1, but Na
is much smaller than Cs. Na will have a higher ionic potential and will interact more strongly with negative surfaces than Cs.
2. Concentration of ions
Si Si Si Si Si
O O O O+ + + +
Chapter 18
Mine dumps – extreme heavy metal concentrations in waste materials which will leach out with rain (usually very acidic conditions from sulfur-containing mineral weathering).
Leach plume can be extensive, damaging, hazardous, and gross!
Wetlands (slow moving water, lots of vegetation) = good “natural” treatment due to deposition and usage of metals (uptake by plants, bacterial degradation, adsorption by clays).
Mine Dumps and WetlandsMine Dumps and Wetlands
Water table extends upwards.
Chapter 18
Acid Mine Drainage: Field Trip
Coal Ash Sampling Trip
Chapter 18
Chemical industry has recognized that it is important to use environmentally friendly chemicals and processes.
There are several goals for green chemistry:• Prevent waste rather than subsequently
cleaning it.• Synthesize new products minimizing waste.• Design energy efficient processes.• Use catalysts as much as possible.• Raw materials should be renewable
feedstocks.• Eliminate solvents as much as possible.
Green ChemistryGreen Chemistry
Chapter 18
Many organic molecules that are used as solvents are volatile and can be environmentally damaging.
Many solvents are also toxic (Please don’t use benzene!).
Liquid or supercritical CO2 is a non-toxic solvent that has many potential applications.
DuPont uses supercritical CO2 to make Teflon™ instead of the environmentally damaging chlorofluorocarbon solvents.
Supercritical: substance has higher than usual T (bp) and P.
Green Solvents and ReagentsGreen Solvents and Reagents
Chapter 18
Supercritical water can be used to make the plastic and polyester fiber PET in place of acetic acid.
Lexan™ polycarbonate, the coatings on CDs, could be made from dimethyl carbonate instead of the very toxic phosgene, which is currently used.
Liquid CO2 is currently used in the dry cleaning industry as an alternative to Cl2C=CCl2, which is toxic.
Ionic liquids can be used in place of acidic solvents.
Green Solvents and ReagentsGreen Solvents and Reagents
Chapter 18
Suggested ProblemsSuggested Problems
Earth’s Atmosphere: 2Upper Atmosphere: 10, 11,
13Troposphere: 17, 20, 22a,
25The World Ocean: 29Freshwater: 41Additional Problems: 57
Chapter 18
End of Chapter 18:End of Chapter 18:Chemistry of the EnvironmentChemistry of the Environment