IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-ISSN: 2278-1684,p-ISSN: 2320-334X, Volume 13, Issue 4 Ver. II (Jul. - Aug. 2016), PP 18-24 www.iosrjournals.org DOI: 10.9790/1684-1304021824 www.iosrjournals.org 18 | Page CFD Analysis ofWind Turbine Airfoil at Various Angles of Attack Ankan Dash (School of Mechanical Engineering, KIIT University, India) Abstract: The main aim of the study was to analyze the NACA0012 wind turbine airfoil at various angles of attack, keeping the Reynolds number constant. The efficiency of the aerodynamic wind turbine is greatly influenced by the aerodynamic efficiency of the airfoil. In the present study NACA0012 airfoil is considered as a suitable wind turbine blade. The geometry and analysis was done using Ansys-Fluent. Calculations were done for constant air velocity altering only the angle of attack. For the computational domain an unstructured mesh with sphere of influence and inflation was selected, taking care of the refinement of the grid near the airfoil in order to enclose the boundary layer approach. The CFD simulation results show close agreement with the results obtained from wind tunnel testing experiments, thus suggesting CFD analysis as a reliable alternative to experimental methods. Keywords: Airfoil, Angle of Attack, CFD, Drag Coefficient,Lift Coefficient I. Introduction Airfoil is defined as the cross-section of a body that is placed in an airstream in order to generate useful aerodynamic force. Compressor and turbine blades, wings of aircraft, propeller blades, windmill blades and hydrofoils are all examples of airfoils. The shape of an airfoil blade is one of the most critical partof a wind turbine, as the blade is responsible for the conversion of kinetic energy to mechanical energy.Computational Fluid Dynamics (CFD) is a branch of fluid mechanics that uses numerical methods and algorithms to solve complex problems involving fluid flow. Some of the recent interesting work in the study of airfoils has been discussed below. Patil et al. [1] investigated the effect of low Reynolds number on lift and drag for the wind turbine blade. They found out as Reynolds number increases, lift and drag forces increases.Haque et al. [2] conducted various experimental studies to understand the effects of Reynolds number and angle of attack in flow analysis. Yao et al. [3] studied the aerodynamic performance of wind turbine airfoils and compared the numerical results with experimental data. The effect of transonic flow over an airfoil has been studied and a comparative analysis hasbeen done to analyze the variation of angle of attack and Mach number [4]. The comparison of various turbulence models (Spalart-Allmaras, Realizable − and − shear stress transport) has been done and it was found out that the turbulence models used in commercial CFD codes does not give accurate results yet at high angle of attack [5]. The mechanism of laminar separation bubble and laminar- turbulent separation over the airfoil has been analyzed by Shah et al. [6] and the relationship between angle of attack and laminar bubble separation, Reynolds number and laminar bubble separation was studied. The analysis of stall angle and its effects on lift and drag coefficient was reported by Sahin et al. [7]. In the light of the review of the existing literature, the present study aims to analyze the flow field for NACA 0012 wind turbine airfoil at various angles of attack with constant Reynolds number of 10 6 . The flow was obtained by solving the steady-state governing equations of continuity and momentum conservation with Realizable − turbulence model and the results were validated by comparing with the available experimental data. Lift Coefficient (C L ): It is a dimensionless quantity that relates the lift generated by airfoil to the fluid density around the body, the fluid velocity and an associated reference area. = 1 2 2 (1) Where, L is the lift force, ρ is the density of air, V is inlet velocity of air, A is the area of airfoil. Drag Coefficient (C D ): It is a dimensional quantity that is used to quantify the drag or resistance of an object in a fluid environment. = 1 2 2 (2)
7
Embed
CFD Analysis ofWind Turbine Airfoil at Various Angles of ... · CFD Analysis of Wind Turbine Airfoil at Various Angles of Attack DOI: 10.9790/1684-1304021824 20 | Page
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE)
e-ISSN: 2278-1684,p-ISSN: 2320-334X, Volume 13, Issue 4 Ver. II (Jul. - Aug. 2016), PP 18-24
V. Conclusion With the help of CFD software Ansys-Fluent, successful analysis of aerodynamic performance of
NACA0012 airfoil has been carried at various angles of attack (4, 6, 8, 10 degree) with constant Reynolds
number (106)using the Realizable𝑘 − 𝜀turbulence model. It is seen that the velocity of upper surface is higher
than the velocity of the lower surface. The pressure coefficient of the airfoil’s upper surface was negative and
the lower surface was positive, thus the lift force of the airfoil is in the upward direction. The coefficient of
pressure difference is much larger on the front edge, while on the rear edge it was much lower. It is observed
that to increase the value of lift force and lift coefficient we have to increase the value of angle of attack. This
leads to rise in drag force and drag coefficient as well, but the increase in drag force and drag coefficient is quite
low in comparison to lift force and lift coefficient. Computed drag and lift forces were found in close agreement
with the experimental values thus corroborating that CFD analysis is an efficient alternative to experimental
methods.
Acknowledgements I would like to sincerely express my deep gratitude to KIIT School of Mechanical Engineering for
providing me an opportunity and necessary facilities to carryout this work.
References [1] Bhushan S. Patil, Hitesh R. Thakare, Computational Fluid Dynamics Analysis of Wind Turbine Blade at Various Angles of Attack
and different Reynolds Number, Procedia Engineering, 127(2015), 1363-1369 [2] NazmulHaque, Mohammad Ali, IsmatAra, Experimental Investigation on the performance of NACA 4412 aerofoil with curved
[3] Jin Yao, Weibin Yuan, Jianliang Wang, JianbinXie, Haipeng Zhou, MingjunPeng, yong Sun, Numerical simulation of aerodynamic performance for two dimensional wind turbine airfoils, Procedia Engineering, 31(2012), 80-86
[4] Novel Kumar Sahu, Mr. Shadab Imam, Analysis of Transonic Flow over an Airfoil NACA0012 using CFD, International Journal
of Innovative Science, Engineering & Technology, Vol. 2 Issue 4, April 2015 [5] Douvi C. Eleni, Tsavalos I. Athanasios, Margaris P Dionissios, Evaluation of the turbulence models for the simulation of the flow
over a National Advisiory Committee for Aeronautics (NACA) 0012 airfoil, Journal of Mechanical Engineering Research, Vol.4(3),pp. 100-111 March 2012
[6] Haseeb Shah, Sathyajith Mathew, Chee Ming Lim, Numerical simulation of flow over an airfoil for small wind turbines using the
𝛾 − 𝑅𝑒𝜃 model, The International Journal of Energy and Environmental Engineering, (2015) 6: 419-429 [7] IzzetSahin, AdemAcir, Numerical and Experimental Investigations of Lift and Drag Performances of NACA 0015Wind Turbine
Airfoil, International Journal of Materials, Mechanics and Manufacturing, Vol. 3, No. 1, February 2015 [8] S. Khandwal, S. Singh, Computational fluid dynamics study of fluid flow and aerodynamic forces on an airfoil, International
Journal of Engineering Research and Technology, 2012 vol. 1, Issue. 7
[9] A. Prabhakar, A CFD analysis of static and dynamic pressure for NACA4412, International Journal of Engineering Trends and Technology, 2013, vol. 4issue 8, pp. 3258-65