CENTURY® L E G E N D A R Y L E A D E R S H I P OWNER'S MANUAL 5025/T INSTALLATION, OPERATION, MAINTENANCE & PARTS NOTE: MANUAL including SPECIFICATIONS, subject to change without notice All ratings specified are based on structural factors only, not vehicle capacities or capabilities. CENTURY® Miller Industries Towing Equipment Inc. 8503 Hilltop Drive FORM NO. 0501084 Ooltewah, Tennessee 37363 04 / 2000 Phone (423) 238-4171 • FAX (423) 238-5371 PRICE $25.00
40
Embed
CENTURY - Miller Industries · PDF fileCENTURY® Miller Industries Towing Equipment Inc. 8503 Hilltop Drive FORM NO. 0501084 Ooltewah, ... 1/2"-13 X 1-1/4" HEX HD CAP 27 6.....
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
CENTURY®
L E G E N D A R Y L E A D E R S H I P
OWNER'S MANUAL
5025/TINSTALLATION, OPERATION, MAINTENANCE & PARTS
NOTE: MANUAL including SPECIFICATIONS, subject to change without noticeAll ratings specified are based on structural factors only,
not vehicle capacities or capabilities.
CENTURY® Miller Industries Towing Equipment Inc. 8503 Hilltop Drive FORM NO. 0501084 Ooltewah, Tennessee 37363 04 / 2000 Phone (423) 238-4171 • FAX (423) 238-5371 PRICE $25.00
LIMITED WARRANTY
MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the original purchaser that each new MILLER wrecker or other MILLER products will be free from defects in material and workmanship for a period of twelve (12) months from date placed in service, but in no event shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER. The purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no event shall MILLER accept such notification later than twenty-four (24) months from date of delivery or twelve (12) months from date placed in service, whichever is earlier.
MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will be used for any replacement at MILLER's option. This warranty is not transferable. This warranty does not obligate MILLER to bear the cost of labor or transportation charges in connection with the repair or replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or alterations have been made unless authorized by MILLER.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime, claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential damages concerning or relating to any product or parts, whether based on negligence, strict liability, breach of contract, breach of warranty, misrepresentation or any other legal theory, regardless of whether the loss resulted from any general or particular requirement which MILLER knew or had reason to know about at the time of sale.
MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or any accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely on such warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent permitted under applicable law, pass on to the purchaser such manufacturer's or seller's warranty.
MILLER, whose policy is one of continuous improvement, reserves the right to improve its products through changes in design or materials as it may deem desirable without being obligated to incorporate such changes in products previously sold. This warranty is not intended to cover or include the following items, which are set forth by way of example and not limitation:
A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to weather, road conditions, road treatments, etc. B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure to provide reasonable and necessary maintenance, or uses for which the equipment was not designed or intended. C. Alterations or modifications that affect performance, operation or reliability. D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts.
IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY OTHER IMPROPER USE.
SERIAL NUMBER Miller Industries Towing Equipment Inc. 8503 Hilltop Drive Ooltewah, Tennessee 37363
Telephone (423) 238-4171
Section VI - PARTS
This Section is provided by the manufacturer for the purpose of orderingany component part of the CENTURY 5025 Wrecker / Integrated Underliftthat may be required when part replacement is necessary. Be certain to useonly original equipment replacement parts for warranty purposes as well asfor keeping your CENTURY 5025 Wrecker / Integrated Underlift in itsoriginal state and optimum operating capacities. When ordering replacementor spare parts be sure to provide the following information to themanufacturerís Parts Department.
1. Manual Number & Date of Publication2. Manual Page Number3. Page Title4. Reference Number of Part Desired5. Part Number6. Part Description7. Quantity of Part Desired
Providing this information will help ensure that the correct parts will bedelivered to you in an expedient manner without delay. Should additionalinformation be required for repair or replacement of certain components,contact your Wrecker Manufacturer Authorized Representative.
The Manufacturer reserves the right, without notice or obligation, to improveor modify their products, which may change the specifications, models andfeature availability.
VI-1
VI-2
Section VI - PARTS (cont'd)SUBFRAME ASSEMBLY
Section VI - PARTS (cont'd)SUBFRAME ASSEMBLY
Section VI - PARTS (cont'd)BODY ASSEMBLY
REF. NO. PARTNO. REQ'D NUMBER DESCRIPTION
1 6 0300113 GREASE FITTING2 REF. 0300438 LIFT CYLINDER3 2 0301861 QUICK PIN4 8 0302540 CENTER BONDED MOUNT5 12 0302541 SPECIAL WASHER6 2 0303089 RAMP PAD7 2 0303445 SAFETY CHAIN, SYSTEM 108 REF. 0303691 SPADE CYLINDER9 8 0400066 SCREW, 1/4"-20 X 3/4" HEX HD CAP10 10 0400128 SCREW, 3/8"-16 X 1-1/4" FL HD SKT11 4 0400139 SCREW, 3/8"-16 X 1-1/2" HEX SKT SET12 2 0400181 SCREW, 1/2"-13 X 1-1/2" HEX HD CAP13 2 0400211 SCREW, 1/2"-13 X 1-3/4" HEX HD CAP14 2 0400219 SCREW, 1/2"-13 X 4-1/2" HEX HD CAP15 4 0400276 SCREW, 5/8"-11 X 4-1/2" HEX HD CAP16 4 0400281 SCREW, 3/4"-10 X 3-1/2" HEX HD CAP17 12 0400286 SCREW, 3/4"-10 X 2-3/4" HEX HD CAP18 4 0400294 SCREW, 3/4"-10 X 6-1/2" HEX HD CAP19 20 0400392 NUT, 3/8"-16 NYLOK HEX20 6 0400408 NUT, 1/2"-13 NYLOK HEX21 4 0400430 NUT, 3/4"-10 NYLOK HEX22 12 0400431 NUT, 3/4"-10 NYLOK HEX23 8 0400452 LOCKWASHER, 1/4" HELICAL24 4 0400492 WASHER, 1/2" FLAT25 8 0400506 WASHER, 5/8" FLAT26 4 0400508 LOCKWASHER, 5/8" HELICAL27 8 0400510 WASHER, 3/4" FLAT28 2 0400563 ROLL PIN, 5/32" X 2-1/2"29 2 0707118 PIN, LIFT CYLINDER30 2 0713128 SHAFT, LOWER SPADE31 2 0713129 SHAFT, UPPER SPADE32 4 0714581 BOLTING PLATE33 2 0715584 COVER PLATE, REAR SPADE34 2 0715694 PIN, SPADE PIVOT35 1 0802211 FRONT BODY MOUNTING TUBE36 2 0802219 PIVOT PIN, LIFT CYLINDER37 2 0803613 BRACKET, BOOM PIVOT38 2 0804286 LOWER SPADE PAD WELDMENT39 1 0804314 5025 SUBFRAME WELDMENT40 2 0804334 PIN, MULTI-POSITION41 1 0804335 LEFT INNER SPADE WELDMENT42 1 0802201 RIGHT INNER SPADE WELDMENT
-- -- 0903535 VALVE PAN ASSEMBLY24 1 0300011 CONTROL VALVE25 2 0300052 ELBOW, 8MJ-10MB9026 2 0301545 ELBOW, 12MJ-12MB9027 2 0301995 STRAIGHT ADAPTER, 8FJ-6MJ28 2 0302052 RUN TEE, 8MJ-8FJX-8MJ29 1 0302782 CONTROL VALVE30 6 0400135 SCREW, 3/8"-16 X 4-1/2" HEX HD CAP31 4 0400157 SCREW, 3/8"-16 X 1-3/4" HEX HD CAP