-
Centralis indoor RTS VB4
Australia: SOMFY PTY LTD(61) 2 9638 0744
Austria: SOMFY GesmbH(43) 662 62 53 08
Belgium: SOMFY BELUX(32) 2 712 07 70
Brasil: SOMFY BRASIL STDA(55 11) 6161 6613
Canada: SOMFY ULC(1) 905 564 6446
Cyprus: SOMFY MIDDLE EAST(357) 25 34 55 40
Czech Republic: SOMFY Spol s.r.o.(420) 296 372 486-7
Denmark: SOMFY AB DENMARK(45) 65325793
Finland: SOMFY AB FINLAND(358) 957 13 02 30
France: SOMFY FRANCE(33) 810 055 055
Germany: SOMFY GmbH(49) 7472 930 0
Greece: SOMFY HELLAS(30) 210 614 67 68
Hong Kong: SOMFY Co. Ltd(852) 25236339
Hungary: SOMFY Kft(36) 1814 5120
India: SOMFY INDIA PVT Ltd(91) 11 51 65 91 76
Italy: SOMFY ITALIA s.r.l(39) 02 4847184
Japan: SOMFY KK+81-45-475-0732
Lebanon: cf. Cyprus - somfy middle east(961) 1 391 224
Mexico: SOMFY MEXICO SA de CV(52) 55 5576 3421
Morocco: SOMFY MAROC(212) 22 95 11 53
Netherlands: SOMFY BV(31) 23 55 44 900
Norway: SOMFY NORWAY(47) 815 00 813
Poland: SOMFY SP Z.O.O(48) 22 618 80 56
Portugal: cf. Spain - SOMFY ESPANA SA(351) 229 396 840
Russia: cf. Germany - SOMFY GmbH(7) 095 781 47 72, (7) 095 360
41 86
Singapore: SOMFY PTE LTD(65) 638 33 855
Slovaquia: cf. Czech Republic - SOMFY Spol s.r.o.(420) 296 372
486-7
South Korea: SOMFY JOO(82) 2 594 4333
Spain: SOMFY ESPANA SA(34) 934 800 900
Sweden: SOMFY AB(46) 40 165900
Switzerland: SOMFY A.G.(41) 18 38 40 30
Taïwan: SOMFY TAIWAN(886) 2 8509 8934
United Kingdom: Somfy LTD(44) 113 391 3030
United States: SOMFY SYSTEMS Inc(1) 609 395 1300
Nothing works: �Check the wiring.�Check the battery of the
transmitter.�Check that the transmitter has been properly
recorded.�Check for any other possible source of radio
interferences.
Phantom intermediate position/slat tilting: �The programmed IP
can only be reached from the UP limit. not when the blind is in
another position.�Be sure to adjust the slat tilting after a down
movement when the blind is approximately 3/4 down of the
window.
Lost in your programming mode: �Just make a complete reset and
start again (refer to section 5).
5 Complete reset
6 Trouble shooting guide
7 Somfy worldwide
To completely reset the CENTRALIS indoor RTS VB, press its PROG
button for more than 7 seconds.This will erase all of the
programmed controls, the intermediate position and the automatic
tilting.
➜ The blind jogs twice (UP/DOWN) : the memory of the CENTRALIS
uno RTS VB is cleared.➜ Tilting mode : back to EU mode
7 sec.
PATE
NTS
AND
DESI
GN P
ATEN
TS P
ENDI
NG F
OR S
OME
COUN
TRIE
S (e
.g.:
US) -
© S
OMFY
SAS,
capi
tal 2
0.00
0.00
Eur
os,R
CS B
onne
ville
303
3.97
0.23
0 -
We
rese
rve
the
right
to m
ake
chan
ges
due
to te
chni
cal i
mpr
ovem
ents
- 0
3/07
Centralis indoor RTS VB_182069E01 28/02/07 8:34 Page 4
-
CENTRALIS indoor RTS VB is an individual control system for AC
motor dedicated to external and interiorvenetian blind
applications.Up to 12 controls can be memorized together in the
memory of Centralis indoor RTS VB allowing individual,group and
master commands.A intermediate position, a slat tilting position or
both can be set.
inteo Centralis indoor RTS VBINSTALLATIONguideRef.182069E
80 mm
80 m
m
45 mm
• Centralis indoor RTS VB 240V• Supply: 220-240V 50 Hz• Fuse:
3,15A• Output timing: 3 minutes• Frequency: 433.42 MHz• Protection
index: IP30• Temperature: +5°C to +40°C• Class II product
Installation allowed only by authorized electrician.Before
connecting the unit, read the instructions carefully.
1Centralis indoor RTS VB
Mounting2.1
1 Characteristics
2 Installationfuse
Centralis indoor RTS VB 240V
Failure to comply with these instructions annuls Somfy’s
responsibilities and guarantee. Somfy cannotbe held responsible for
any changes in norms and standards introduced after the publication
of thisguide. Hereby, SOMFY, declares that this product is in
compliance with the essential requirements andother relevant
provisions of Directive 1999/5/EC. A Declaration of Conformity is
available at the webaddress www.somfy.com/CE. Usable in EU, �
Recommandation of mounting for better radio reception:minimum
distance between Centralis indoor RTS VB and the floor: 1,5
m.minimum distance between a Centralis indoor RTS VB and a radio
transmitter: 30 cm.minimum distance between two Centralis indoor
RTS VB: 20 cm.Warning: cordless radio equipment (e.g. headphones)
in 433MHz can affect the functionning of the Centralis indoor RTS
VB.
Recessed mounting: Surface mounting:
Wiring2.2
3 wires x 1.5 mm24 wire
s x 0.
75 m
m2
• disconnect the mains before carrying out any work.• ensure
that no forces act on the screw terminals after installation.
L Live.N Mains Neutral. N Motor neutral .▲ UP direction.▼ DOWN
direction.
WARNING: if the venetian blind moves DOWN when pressing the UP
button of the RTS controls,invert the ▲ and ▼ motor wires (black
and brown wires).
Programing Button
LED
Built-in manualsecurity control
Centralis indoor RTS VB_182069E01 28/02/07 8:34 Page 1
-
GROUP CONTROL (one transmitter for several receivers)To program
one control in several Centralis indoor RTS VB, set all the
receivers in their programming mode then repeat the same procedure
as described in 3.1.
It is recommended not to use the INIS RT control only as a
general control point.
MULTIPLE CONTROL (several transmitters for one receiver)To add
several RTS controls to the Centralis indoor RTS VB, repeat the
same procedure as described in 3.1 for each control.You can program
up to 12 controls to one receiver. If you try to enter a 13th, your
instruction will be ignored.
Add a new control in the Centralis indoor RTS VB’s memory3.2
Remove a control in the Centralis indoor RTS VB’s memory (on an
existing installation)3.3
Remove all controls from the memory of a Centralis indoor RTS
VB3.4
CENTRALIS indoor RTS VB can be operated by its push-buttons or
with a RT/RTS control.CENTRALIS indoor RTS VB offers two different
modes to control the venetian blind.
UP/DOWN/STOP commands
• To add a new control in the memory of a RTS receiver, set the
Centralis indoor RTS VB in its programming mode (§ 3.1), then press
shortly the prog buttonthe RTS control you wish to add (to add an
INIS RT, short contact between the PROG metallic part and the
battery support).
• It is also possible to “wake up” the Centralis indoor RTS VB
with another control.From a RTS control already recorded: press for
more than 2 seconds on the prog button of the RTS control, then
press shortly the prog button of RTS controlyou wish to add or
delete (to add or delete an INIS RT, short contact between the PROG
metallic part and the battery support).From a RT control already
recorded: contact of 2 seconds (between the PROG metallic part and
the battery support), then press shortly the prog button of theRTS
control you wish to add or delete (to add or delete another INIS
RT, short contact between the PROG metallic part and the battery
support).
• To remove a RTS control from the memory of a RTS receiver, set
the Centralis indoor RTS VB in its programming mode (§ 3.1), then
press shortly the progbutton of the RTS control you wish to remove
(to remove an INIS RT, short contact between the PROG metallic part
and the battery support).
• It is also possible to “wake up” the Centralis indoor RTS VB
with another control.From a RTS control already recorded: press for
more than 2 seconds on the prog button of the RTS control, then
press shortly the prog button of RTS controlyou wish to add or
delete (to add or delete an INIS RT, short contact between the PROG
metallic part and the battery support).From a RT control already
recorded: contact of 2 seconds (between the PROG metallic part and
the battery support), then press shortly the prog button of theRTS
control you wish to add or delete (to add or delete another INIS
RT, short contact between the PROG metallic part and the battery
support).
• To completely reset the CENTRALIS INDOOR RTS VB, press its
PROG button for more than 7 seconds.This will erase all of the
programmed controls, the intermediate positions.
The blind jogs twice (UP/DOWN), and the led blinks 5 secs. The
memory of the CENTRALIS Indoor RTS VB is cleared.
➜0,5 s
RTS controlPress briefly theprogramming buttonon the RTS
controlyou wish to record.
RT controlShort contact between the PROGmetallic part and the
battery support,on the RT control you wish to record.
0,5 s
Centralis indoor RTS VB2
The blind jogs briefly (UP/DOWN) and theled of the Centralis
indoor RTS VB blinks5 secs. Indicating the control has
beenrecorded.The Centralis indoor RTS VB quits itsprogramming
mode.
Set the Centralis indoor RTS VB in itsprogramming mode by
pressing the PROGbutton until the LED lights and the blind
jogsbriefly (UP/DOWN).The CENTRALIS indoor RTS VB will remainready
to record a control for two minutes.
3 Radio programmingFirst programming3.1
EU mode (factory mode):• To raise or lower the blind, press and
hold more than 2 secs. the c or a buttons.• To stop the blind,
press briefly the e button.• To tilt the slats, press briefly the c
or a buttons.
US mode• Press briefly the c or a buttons to raise or lower the
blind.• Press briefly the e button To stop the blind.• To tilt the
slats, press and hold the c or a buttons.
If you hold the control buttons for more than 6, seconds, the
blind will start to move continuously up to its end limits.
With an RTS control:
UP buttonSTOP/IP button
DOWN button
4.1
21
4 Operating
Centralis indoor RTS VB_182069E01 28/02/07 8:34 Page 2
-
• Press the e button more than 5 sec.➜ The blind jogs briefly
(UP/DOWN),the intermediate position is recorded.
3Centralis indoor RTS VB
With an INIS RT:Press the control button to operate the shutter:
UP -> STOP -> DOWN -> STOP...
STOP
STOP➜
After the power on and during 30 seconds, the configuration can
be changed by pressing for more than 5 secs. on the e button of a
RTS control. The blindjogs, indicating that CENTRALIS indoor RTS VB
has changed the configuration.After the power on :• EU mode : the
led blinks once• US mode : the led blinks twice
With the CENTRALIS indoor RTS VB, it is possible to program an
automatic intermediate position (IP) and an automatic tiltingof the
slats. You can choose to program one or the other, or both. The
recording of the intermediate position and the tilting canbe made
from a RTS control.
Intermediate position / automatic slat tilting4.2
• Move the blind at its UP limit with thec button and
immediately press thee button briefly.
• Press the a and e button simulta-neously until the blind
begins to moveDOWN.
• Stop the blind at the intermediateposition you wish. If
necessary, adjust this position withthe c or a buttons.
STOP
IP
• Press briefly the e button while the blindis at its UP limit.➜
The blind will move and stop at the inter-mediate position.
• Press briefly the e button while the blind is at its UP
limit.➜ The blind will move, stop at the intermediate position and
tiltat the pre-set angle.Note : after a DOWN movement the blind
only tilts.
• Press briefly the e button while the blindis closed (after a
DOWN movement).➜ The blind will tilt at the pre-set angle.Note :
after an UP movement the blinddoes not tilt.
IP
adjustthe angle
Set the blind to its UP limit before programming in order to
always have the same adjustment.
If IP only has been programmed If tilting only has been
programmed If both IP and tilting have been programmed
21 3 4
5 s
5 s5 s
UP limit
Programming the intermediate position (IP)a
Programming the automatic slat tiltingb
Operatingc
If you record a new IP or a new tilting function, this will
automatically erase the previous one.If you want to erase without
recording a new one, Press briefly on the e button to reach the IP
or to get the tilting (or both), then:
� To erase the intermediate position, press the a and e buttons
simultaneously for more than 5 seconds.� To erase the tilting,
press the e and c buttons simultaneously for more than 5 seconds.�
To erase both, just press the e button for more than 5 seconds.
➜ The blind jogs briefly (UP/DOWN) indicating that CENTRALIS
indoor RTS VB has deleted the intermediate position and/or the
tilting.
Delete the intermediate position/automatic tiltingd
21 3 4
• Move the blind downward to get theslats closed.
• Press simultaneously on the c ande button until the blind
begins tomove briefly UP.
• Adjust the tilt angle with the c ora buttons.
• Press the e button more than 5 sec.➜ The blind jogs briefly
(UP/DOWN),the tilt angle is recorded.
UP limit
tilting tilting
IPafter
3 seconds
after 3 seconds
Centralis indoor RTS VB_182069E01 28/02/07 8:34 Page 3
/ColorImageDict > /JPEG2000ColorACSImageDict >
/JPEG2000ColorImageDict > /AntiAliasGrayImages false
/DownsampleGrayImages false /GrayImageDownsampleType /Average
/GrayImageResolution 300 /GrayImageDepth -1
/GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages false
/GrayImageFilter /None /AutoFilterGrayImages true
/GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict >
/GrayImageDict > /JPEG2000GrayACSImageDict >
/JPEG2000GrayImageDict > /AntiAliasMonoImages false
/DownsampleMonoImages false /MonoImageDownsampleType /Average
/MonoImageResolution 1200 /MonoImageDepth -1
/MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages false
/MonoImageFilter /None /MonoImageDict > /AllowPSXObjects false
/PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false
/PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000
0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true
/PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ]
/PDFXOutputIntentProfile () /PDFXOutputCondition ()
/PDFXRegistryName (http://www.color.org) /PDFXTrapped /Unknown
/Description >>> setdistillerparams>
setpagedevice