CellClutch - Apex Tool Group

CellClutch™

For additional product information visit our website at www.ClecoTools.com

Quick Installation GuideP2570KA-EN

2021-04

S168715Desktop Application

P2570KA | 2021-04 Apex Tool Group

Copyright © Apex Tool Group, 2021

No part of this document may be reproduced in any way or in any form, in whole or in part, or in a natural or machine-readable language, or transmitted on electronic, mechanical, optical, or other media, without the express permission of the Apex Tool Group.

DisclaimerApex Tool Group reserves the right to modify, supplement, or improve this document or the product without prior notice.

TrademarkCleco is a registered trademark of Apex Brands, Inc.

Apex Tool Group670 Industrial DriveLexington, SC 29072USA

ManufacturerApex Tool Group GmbHIndustriestraße 173463 WesthausenGermany

Apex Tool Group P2570KA | 2021-04 3

ENContents1 About this document............................................................................. 4

2 Installation ............................................................................................ 52.1 System Requirements ................................................................................................. 52.2 Installing the software.................................................................................................. 5

3 Operation.............................................................................................. 73.1 Product Information ..................................................................................................... 73.2 General Settings.......................................................................................................... 83.3 Advanced Settings ...................................................................................................... 93.4 Tool Actions ................................................................................................................. 93.5 Application Settings................................................................................................... 103.6 Menu Bar................................................................................................................... 11

About this document

4 P2570KA | 2021-04 Apex Tool Group

1EN 1 About this document

This document contains instructions and notes:• for safe, appropriate and effective handling of the product. • for installation, configuration and function.• for programming the software.

Software version: S168715-0.9.3.

The original language of this document is English.

Symbols in the textitalic Menu options (e.g.,Diagnostics) input fields, check boxes, radio buttons or dropdown

menus.> Indicates selection of a menu option from a menu, e.g., File > Print

<…> Specifies switches, pushbuttons or the keys of an external keyboard, e.g., <F5>Courier Filenames and paths, e.g., setup.exe• List

- List, level 2a)b)

Options

→ Result1. (...)2. (...)

Action steps

Single action step

Installation2EN

2.1 System Requirements• Windows 10 64-Bit• Screen resolution of 1280 x 800 or higher recommended

2.2 Installing the softwareThe software is delivered in the form of an executable installation package.

1. Download the software package CellClutch from the website: https://software.apextoolgroup.com/current-software-packages/cellclutch/

2. Start the installation file CellClutch-X.Y.Z.exe.

3. Select a language and press <OK>.

4. Select the installation folder and press <Next>.

5. Select components to be installed and press <Next>.

Apex Tool Group P2570KA | 2021-04 5

Installation2

EN

6. Press <Next>.

7. Confirm the installation with <Install> before it starts.

6 P2570KA | 2021-04 Apex Tool Group

Operation3EN

The user interface is divided into three parts. On the left are global settings and actions, in the middle are forward application settings, and on the right are reverse application settings:

Fig. 3-1: User interface with exemplary settings

The individual panes of the user interface are described below.

3.1 Product InformationIn this pane information about the tool is displayed.

Fig. 3-2: Product Information

The current software is a beta version. Functions can still change until the final release.

Parameter DescriptionSerial Number This read-only field shows the serial number of the tool. If no tool is con-

nected, Not Connected is displayed. If no serial number is stored in the con-nected tool, Not available is displayed.

ID This read-only field shows the ID of the tool. If no tool is connected, Not Connected is displayed. If no ID is stored in the connected tool, Not avail-able is displayed.

Apex Tool Group P2570KA | 2021-04 7

Operation3

EN

3.2 General SettingsGeneral settings can be made in this pane.

Fig. 3-3: General Settings - View of the default settings

Status displayThe color of the LEDs indicates the status of the rundown and tool.

Revision This field shows the software version of the tool.Note This field allows to store a remark in the tool.

Parameter Description

Parameter DescriptionEnable Rotation It is possible to set which direction of rotation should be active: Only for-

ward, only reverse or both. If forward is selected, the reverse program can-not be used, and vice versa.

Work Light The brightness of the work light can be configured.Status Light The status light can be turned on or off.Buzzer The buzzer can be turned on or off.Brake If the brake is active, the motor brakes as soon as the trigger is released,

otherwise the motor coasts.

The dark gray buttons indicate the selected option, while the light gray ones show the unselected ones.

Message Color Worklight Color Status BuzzerOK result Continuous green light Continuous green lightNOK result Continuous red light Continuous red light xCross thread detection Continuous red light Continuous red light xRehit Protection / Dou-ble Hit

Continuous red light Continuous red light x

During batch Continuous green light Continuous blue lightBatch OK (single result) - Continuous green lightBatch OK (completed) Continuous green light Flashing light green and blue xBatch NOK (completed) Continuous red light Continuous red and blue lightTool overheating Flashing light red Flashing light redMaintenance alarm - Flashing light red - blue -

greenBattery low

→ Tool stops auto-matically

Flashing light red - blue Flashing light red - blue

8 P2570KA | 2021-04 Apex Tool Group

Operation3EN

3.3 Advanced SettingsSome advanced settings can be made in this pane.

Fig. 3-4: Advanced Settings

3.4 Tool ActionsSome tool actions can be made in this pane.

Fig. 3-5: Tool Actions

Check of the LED indica-tor, light and buzzer during first install battery operation.

Flashing light red - blue - green

Flashing light red - blue - green

xMessage Color Worklight Color Status Buzzer

Parameter DescriptionRestart Delay The restart delay can be configured here. This means the minimum time

between a clutch event and the start of the next run.Double Hit Double hit protection can be activated and configured here.

A second clutch event within the double hit time automatically leads to a NOK indication. This is to detect a tightening that has already been tight-ened by the previous run.

Gear Translation The gear translation ratio configured in the tool is displayed here. Please note that the value can currently only be read at this point.

Parameter DescriptionConnect (Serial Port) Connect to a tool via a virtual serial port (USB). The following dialog

appears:

Select the COM port to which the tool is connected and click OK. If Read Settings is selected, the settings (global and application settings) are read automatically after the connection is established.

Reconnect Reestablish the connection. If there is no connection at the moment, the last existing connection will be re-established.

Apex Tool Group P2570KA | 2021-04 9

Operation3

EN

3.5 Application SettingsIt is possible to set separate tightening programs for forward and reverse operation.

Fig. 3-6: Example Stage 1

The pre-tightening stages 1-5 and the After Clutch Stage can be configured this way:

The Tightening Stage can be configured this way:

Disconnect Disconnect current connection.Read Settings Read settings (global and application settings) from the currently connected

tool. Write Settings Write settings (global and application settings) to the currently connected

tool.Download results Download tightening results from the currently connected tool. The following

dialog appears:

Select the file format and click OK. After that another dialog appears to select the target file.

Parameter Description

Parameter DescriptionStage X With the checkbox in the pane title it is possible to disable the stage com-

pletely. In this case the pane will be collapsed.Rotation The direction of rotation can be set to either forward or reverse.Speed The rotation speed can be set here.Condition The condition when the stage is completed can be selected. Either the

angle of rotation or the duration is monitored.Angle/Duration Depending on which condition is selected, the angle or the time can be set

here.

Parameter DescriptionTightening Stage This stage cannot be disabled because it is mandatory.Rotation The direction of rotation is always forward in this stage. It cannot be

changed.Speed The rotation speed can be set here.Limit Type Here you can set whether the angle or the duration is limited during tighten-

ing.Angle/Duration Limit Depending on which limit type is selected, the angle or the time can be set

here.

In the reverse operation mode no Tightening Stage and no After Clutch Stage is available. However, at least one stage must be active in reverse operation mode.

10 P2570KA | 2021-04 Apex Tool Group

Operation3EN

The menu bar offers several useful menus:

Menu FunctionFile • Open: Load the settings from a file.

• Save as: Save the settings to a file.• Preferences: Provides options to configure the App:

- Automatically connect on startup: If this option is selected, a connection to the last connected tool is established at startup.

- Read settings after automatic connect: If this option is selected, after the auto-matic connection establishment the settings are read from the tool.

• Exit: Close the App.Edit • Undo: Undo the last change to the settings.

• Redo: Restore the next change to the settings (Undo the last undo).Tool The tool menu offers the same functions as the tool actions pane described above.Language Change the user interface language.Help • Open Log Directory: Open the directory where log files are stored.

• Open Latest Log File: Open the latest log file with the system's default text editor.

Apex Tool Group P2570KA | 2021-04 11

0421 | Cleco® is a registered trademark of Apex Brands, Inc. | © 2021

Apex Tool Group, LLCPhone: +1 (800) 845-5629

Phone: +1 (919) 387-0099

Fax: +1 (803) 358-7681

www.ClecoTools.com

www.ClecoTools.de

POWER TOOLS SALES & SERVICE CENTERS

Please note that all locations may not service all products.Contact the nearest Cleco® Sales & Service Center for the appropriate facility to handle your servicerequirements.

Sales Center

Service Center

NORTH AMERICA | SOUTH AMERICADETROIT, MICHIGAN Apex Tool Group2630 Superior CourtAuburn Hills, MI 48236Phone: +1 (248) 393-5644Fax: +1 (248) 391-6295

LEXINGTON, SOUTH CAROLINA Apex Tool Group670 Industrial DriveLexington, SC 29072Phone: +1 (800) 845-5629Phone: +1 (919) 387-0099Fax: +1 (803) 358-7681

MEXICO Apex Tool GroupVialidad El Pueblito #103Parque Industrial QuerétaroQuerétaro, QRO 76220MexicoPhone: +52 (442) 211 3800Fax: +52 (800) 685 5560

BRAZIL Apex Tool GroupAv. Liberdade, 4055Zona Industrial IporangaSorocaba, São PauloCEP# 18087-170BrazilPhone: +55 15 3238 3870Fax: +55 15 3238 3938

EUROPE | MIDDLE EAST | AFRICAENGLAND Apex Tool Group GmbHC/O Spline GaugesPiccadilly, TamworthStaffordshire B78 2ERUnited KingdomPhone: +44 1827 8727 71Fax: +44 1827 8741 28

FRANCE Apex Tool Group SAS25 Avenue Maurice Chevalier - ZI77330 Ozoir-La-FerrièreFrancePhone: +33 1 64 43 22 00Fax: +33 1 64 43 17 17

GERMANY Apex Tool Group GmbHIndustriestraße 173463 WesthausenGermanyPhone: +49 (0) 73 63 81 0Fax: +49 (0) 73 63 81 222

HUNGARY Apex Tool GroupHungária Kft.Platánfa u. 29027 GyörHungaryPhone: +36 96 66 1383FAX: +36 96 66 1135

ASIA PACIFICAUSTRALIA Apex Tool Group519 Nurigong Street, AlburyNSW 2640AustraliaPhone: +61 2 6058 0300

CHINA Apex Power Tool Trading(Shanghai) Co., Ltd.2nd Floor, Area C177 Bi Bo RoadPu Dong New Area, ShanghaiChina 201203 P.R.C.Phone: +86 21 60880320Fax: +86 21 60880298

INDIA Apex Power Tool IndiaPrivate LimitedGala No. 1, Plot No. 5S. No. 234, 235 & 245Indialand GlobalIndustrial ParkTaluka-Mulsi, Phase IHinjawadi, Pune 411057Maharashtra, IndiaPhone: +91 020 66761111

JAPAN Apex Tool Group JapanKorin-Kaikan 5F,3-6-23 Shibakoen, Minato-Ku,Tokyo 105-0011, JAPANPhone: +81-3-6450-1840Fax: +81-3-6450-1841

KOREA Apex Tool Group Korea#1503, Hibrand Living Bldg.,215 Yangjae-dong,Seocho-gu, Seoul 137-924,KoreaPhone: +82-2-2155-0250Fax: +82-2-2155-0252