CEILING MOUNT ADDENDUM 2/3/2020 Ceiling Mount 4000 Ceiling Mount 8000 Ceiling Mount Twin
CEILING MOUNTADDENDUM
2/3/2020
Ceiling Mount 4000
Ceiling Mount 8000
Ceiling Mount Twin
Copyright © 2020. WhisperKOOL. All rights reserved.
WhisperKOOL copyrights this manual, the product design, and the design concepts, with all rights reserved. Your rights with regard to the hardware and manual are subject to the restrictions and limitations imposed by the copyright laws of the USA. Under copyright laws, this manual may not be copied, reproduced, translated, transmitted, or reduced to any printed or electronic medium or to any machine-readable form, for any purpose, in whole or in part, without the written consent of WhisperKOOL.
Every effort has been made to ensure that the information in this manual is accurate. WhisperKOOL is not responsible for printing or clerical errors.
WhisperKOOL reserves the right to make corrections or improvements to the information provided and to the related hardware at any time, without notice.
Vinothèque and WhisperKOOL are registered trademarks, and ECE is a trademark of WhisperKOOL. All rights reserved.
Mention of third-party products is for informational purposes only and constitutes neither an endorsement nor a recommendation. WhisperKOOL assumes no liability with regard to the performance or use of these products.
We manufacture, test and certify 100% of our wine cooling units in the USA. By sourcing the best components and closely controlling our
manufacturing processes, we can assure the highest-quality, lowest defect manufacturing rates in the industry.
Conforms to ANSI/UL Std 427
Certified to CAN/CSA Std C22.2 No. 120
TABLE OF CONTENTS
Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Line Set, Drain Tube, and Electrical Connections . . . . . . . . . . . . . . . . . 4
Additional Access Holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Speed Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Insulation Blanket Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Copyright © 2020. WhisperKOOL. All rights reserved.
WhisperKOOL copyrights this manual, the product design, and the design concepts, with all rights reserved. Your rights with regard to the hardware and manual are subject to the restrictions and limitations imposed by the copyright laws of the USA. Under copyright laws, this manual may not be copied, reproduced, translated, transmitted, or reduced to any printed or electronic medium or to any machine-readable form, for any purpose, in whole or in part, without the written consent of WhisperKOOL.
Every effort has been made to ensure that the information in this manual is accurate. WhisperKOOL is not responsible for printing or clerical errors.
WhisperKOOL reserves the right to make corrections or improvements to the information provided and to the related hardware at any time, without notice.
Vinothèque and WhisperKOOL are registered trademarks, and ECE is a trademark of WhisperKOOL. All rights reserved.
Mention of third-party products is for informational purposes only and constitutes neither an endorsement nor a recommendation. WhisperKOOL assumes no liability with regard to the performance or use of these products.
Page 2 | 1-800-343-9463 CM-A 020320
WARNINGThe evaporator unit (fan coil unit) must be insulated using the insulation blanket provided in accordance with this manual. Refer to the insulation blanket installation instructions.
Failure to follow the instructions provided will result in a poor vapor barrier, water damage, rust, and system corrosion which will void the warranty on your unit.
The evaporator unit (fan coil unit) must be insulated using fiberglass insulation (R19 or higher) in addition to the provided insulation blanket. This includes the cavity between the ceiling joists. A warm attic environment will reduce the capacity of the cooling system, as the system will absorb heat from the attic in addition to the heat load from the wine cellar. This, in effect, will significantly reduce the cooling system’s ability to cool the wine cellar.
Failure to properly insulate the evaporator unit may cause condensation to form on the surface of the housing and water damage to the surrounding structure, the cooling unit, and possibly the wine cellar.
To avoid these issues, install the insulation kit and insulate the surface of the evaporator unit that is located outside of the wine cellar using fiberglass insulation.
*Additional insulation is required!
www.whisperkool.com | Page 3
Ceiling Mount - Addendum
Washable filter is installed from the factory on the return side of the grille, secured via Velcro strips.FILTER
Page 4 | 1-800-343-9463 CM-A 020320
LINE SET, DRAIN TUBE, and ELECTRICAL CONNECTIONS• Line set, drain tube and electrical connections have been relocated to be accessible from the bottom (cellar side / grille
side) located on return side of unit.• Can be accessed by removing the grille.• Flare fittings have been added to the line set.• Liquid line – ¼” flare fitting.• Suction line – ½” flare fitting.• Connect Flare nuts from line set to system using Crescent wrenches or torque wrench.• Pressure test is mandatory after connecting line set to the unit.
• Verify there are no leaks before beginning vacuum and charging process.
ADDITIONAL ACCESS HOLES• Top access holes.
• 1 large hole for line set. • 1 small hole for electrical. • Note: do not run electrical wiring through same hole as line set.
• Side access holes. • 1 large hole for line set. • 1 small hole for electrical. • Note: do not run electrical wiring through same hole as line set.
• Use the provided plug to cover the small hole not in use.• Use the provided sticker (4” x 4”) to cover the large hole not in use.• Use the provided strain relief clamp to route electrical wiring into unit.• Seal around line set hole with cork tape, or other insulation to ensure proper seal.• Note: side access holes will be applicable only if utilizing the flush mounting option.
www.whisperkool.com | Page 5
Ceiling Mount - Addendum2 SPEED SWITCH
• The WhisperKool Ceiling mount now comes equipped with a 2-speed fan switch.• Located on the electrical panel. Access by removing grille and internal access panel.• Speed is sent from factory set to High. Flip the switch to adjust down to Medium speed.
Page 6 | 1-800-343-9463 CM-A 020320
__ Min. Tack Time
Adhesive
__ Min. Cure Time
Directions__ Min. Tack Tim
eDirections
INSULATION BLANKET INSTALLATION
1. Once mounting bracket location has been selected and installed, proceed to the insulation blanket installation.
2. Spray adhesive onto the sides of the portions of the evaporator unit and mounting bracket which protrude into the attic. See spray adhesive directions for proper tack time before proceeding to step 3 (see illustration).
3. Wrap insulation piece (A) around the sides of the evaporator unit. Make sure the bottom edge of the insulation is flush with the top edge of the mounting bracket (see illustration).
4. Set insulation in place by pressing firmly on all surfaces of the insulation that come in contact with the sides of the evaporator unit (see illustration).
5. Using a utility knife, cut holes in the insulation for the line set, wiring, and drain line if needed.
6. If necessary, cut the insulation to size using the top edge of the
An external Insulation Blanket is included with the purchase of each Ceiling Mount. It is mandatory that the insulation blanket be installed on the exterior of the Ceiling Mount unit prior to unit installation in the ceiling.
• Ceiling Mount evaporator dimensions (including insulation blanket): 36.25”L x 15”W x 13”H.• Whisperkool recommends constructing the frame using dimensions which include the insulation blanket to ensure
proper fitment.
*Tools required: spray adhesive, utility knife, cork tape, foil tape
A
H
H
H
H
11.25”
14.25”
68”
Insulation Blanket B
Insulation Blanket B
Mini Ceiling Mount blanket dimensions
Ceiling Mount blanket dimensions
22”
102”35.75”
14.25”
11”
Insulation BlanketA
Insulation BlanketA
If needed, trim excess insulation around all edges.
A
AA
www.whisperkool.com | Page 7
Ceiling Mount - AddendumINSULATION BLANKET INSTALLATION, CONTINUED
before proceeding to step 8.)
8. Set piece (B) in place by pressing firmly on all surfaces of the insulation that come in contact with the top of the
evaporator unit (see illustration).
9. Using a utility knife, cut holes in the insulation for line set, wiring, and drain line if needed.
10. Once insulation is installed, apply foil tape to all seams, covering them completely.
11. Inspect insulation for damage/defects. If damaged, repair with foil tape.
12. Apply cork tape or equivalent to areas where the line set, wiring, and drain line enter the unit.
If needed, trim excess insulation around all edges.
A__ Min. Tack Time
Adhesive
__ Min. Cure Time
Directions__ Min. Tack Tim
eDirections
B
A
B
A
evaporator unit as a template. Remove excess insulation. Proceed to piece (B) installation.
7. Spray the top of the evaporator unit with spray adhesive. (See spray adhesive directions for proper tack time
Page 8 | 1-800-343-9463 CM-A 020320
WIRING DIAGRAMS
1 4
Black
GreenWhite
Bro
wn
Blue
Whi
te
Ref.
Solenoid
Green
CondensatePump
Yel
low
Bla
ck
Whi
te
Bla
ck
Bla
ck
Control PanelGround Stud.
Unit GroundStud
Whi
te
115V Line115V Neutral
Ground
ReservoirGreen
12345
24v
Tran
sfor
mer
10
4 6
Blue
Ceiling Mount 24V Thermostat Conversion Kit
1 2 3 4 5
10
4 6
FanRelay
1 4
Line
Neu
tral
Fan
Sole
noid
1 2 3 4 5
Black
BlackWhite
Bla
ckB
lack
Bla
ck
Whi
te
Yel
low
Blu
eB
lue
Blu
eB
lue
Blu
e
Yellow
Green
RedC
GY
R
24VThermostat
RC
Field InstalledLEGEND
Factory Installed
Solenoid orCompressorRelay
Blue
Bla
ckB
lack
146mmAFL
Blower
GREEN
BLACK
WH
ITE
YEL
LOW
BROWNGREY
Capacitor
BLUE
123
CONDENSATEPUMP
BLA
CK
YEL
LOW
BLA
CK
1 4
BLACK
GREEN
BLUE
WHITE
(4)
Ref.
Solenoid
GREEN
WH
ITE
BLA
CKWHITE
WH
ITE
115V LINE115V NEUTRAL
GROUND
12345
RESERVOIR
BLA
CK
BLA
CK
(1)1 4
WHITEBLACK
BLACK
12
34
5
BLACKBLACK
BLU
E
BLACK
LINENEUTRAL C NCNO C NC NO C NO C NO
NEUTRAL LINE OUT 2 OUT 3
OUT 1
OUT 4
B Probe
Evap
ELIWELL RTN400
PANASONIC
Pb1Pb2Pb3 CPB CPBCPB
12V
DGN
D
KEYB
DI
1 3 4 5 6 7 8 9 10 11 12 13 14
KDT PLUS DISPLAY
146mmAFL
Blower
GREEN
BLACK
BLUE
WH
ITE
YEL
LOW
BROWNGREY
Capacitor
BLACK
BROWN
CMVERSION 3
123
www.whisperkool.com | Page 9
Ceiling Mount - Addendum
WIRING DIAGRAMS
CONDENSATEPUMP
BLA
CKYE
LLO
W
BLA
CK
1 4
BLACK
GREEN
BLUE
WHITE
(4)
Ref.
Solenoid
GREEN
WH
ITE
BLA
CK
WHITE
WH
ITE
115V LINE115V NEUTRAL
GROUND
12345
RESERVOIR
(1)1 4
WHITEBLACK
BLACK
12
34
5
BLACKBLACK
BLU
E
BLACK
LINENEUTRAL C NCNO C NC NO C NO C NO
NEUTRAL LINE OUT 2 OUT 3
OUT 1 OUT 4
B Probe
Evap
ELIWELL RTN400
PANASONIC
Pb1Pb2Pb3 CPB CPBCPB
12V
DGN
D
KEYB
DI
1 3 4 5 6 7 8 9 10 11 12 13 14
KDT PLUS DISPLAY
NC C NO3 4 2
7 8 6
1
0
24vTransformer
WHITE
WHITE
WH
ITE
WHITEREDYELLOW
BLUEBLACK
GREENBLUE
24V 18-5 THERMOSTATWIRES GOING TO SLAVEUNIT
CM TWIN MASTER UNITWIRING DIAGRAM
Field InstalledLEGEND
Factory Installed
YELLOW
BLA
CK
146mmAFL
Blower
GREEN
BLACK
BLUE
WH
ITE
YEL
LOW
BROWNGREY
Capacitor
BRO
WN
123
CM TWIN SLAVE UNIT WIRING DIAGRAM(STANDARD AND 24V TCK)
1 4
BLACK
GREEN
BR
OW
N
BLUE
Ref.
Solenoid
GREEN
CONDENSATEPUMP
WH
ITE
BLA
CK
BLA
CK
1 4
LIN
E
FAN
SOLE
NO
ID
12
34
5
1 0
46
12
34
5
1 0
46
BLACKBLACK BLUE
BLUE
BLU
E
BLA
CK
BLUEGREEN
YELLOW
BLA
CK
Field InstalledLEGEND
Factory Installed
WHITE
12345
WHITE
YEL
LOW
BLA
CK
115V LINE115V NEUTRAL
GROUND
RESERVOIR
GREEN
Solenoid Relay Fan Relay
BLACK
BLUEGREEN
YELLOWRED
WHITERED
BLACK WHITERED
24V 18-5 THERMOSTATWIRES COMING FROMMASTER UNIT
146mmAFL
Blower
GREEN
BLUE
BLACK
WH
ITE
YEL
LOW
BROWNGREY
Capacitor
123
WhisperKOOL1738 E. Alpine Ave
Stockton, CA 952051-800-343-9463
www.whisperkool.com