CDC 10027W Driver/Operator - Aircraft Rescue and Fire Fighting Performance Test Extension Course Program (A4L) Air University Air Education and Training Command
CDC 10027W Driver/Operator - Aircraft Rescue and Fire Fighting
Performance Test
Extension Course Program (A4L) Air University
Air Education and Training Command
Acknowledgement
ii
Preparation of this supplement was aided through the cooperation and courtesy of the International Fire Service Training Association (IFSTA). IFSTA furnished technical materials utilized to develop this training product. Permission to use the information from IFSTA is gratefully acknowledged.
In accordance with the copyright agreement, distribution of this volume is limited to United States Government personnel.
Performance Test Instructions
iii
This performance test supplement is based on the 2009 Edition of NFPA 1002; Standard for Fire Apparatus Driver/Operator Professional Qualification and provides the detailed performance test checklist items required for candidate testing.
Performance tests should not be conducted until the candidate has successfully completed the academic portion of the CDC. However, it is strongly encouraged that this supplement and the checklist it contains be used during the normal course of study. Candidates may practice the performance tests at anytime during study and up until testing is conducted. Practice is highly encouraged.
This particular course uses three workstations. Within each workstation there are several tasks and objectives (NFPA line items). A “Performance Summary Sheet” precedes each workstation or group of evaluated tasks. This sheet lists the NFPA line items evaluated and the specific tasks that must be accomplished. Each performance test lists the setting and tools/equipment required for the listed tasks.
Remember, official performance test notifications must be made ten days prior to the actual performance test or the candidate’s performance test results will not be accepted by the DoD Administrative Center. For specific program guidance see DoD Manual 6055.6. Your performance test notifications must be made using the following web site. http://www.dodffcert.com/performance/notify.cfm
It is important also to understand the grading process used during the evaluation. For a full overview of the CDC process and performance testing please view the Department of Defense Fire Fighter Certification Program Video P/N # 612288. Additional information on grading criteria is provided on the next page.
Grading Criteria
iv
The following criteria will be used to evaluate and determine the pass/fail status of a candidate. Each item in the Performance Test Checklist is given a rating. Critical (C) – This rating has been assigned to items which, if omitted or performed incorrectly, would result in severe injury to, or death of an individual. Should a fire fighter fail to perform any one item rated as Critical (C), the fire fighter would be unsuccessful in attaining the required proficiency level for that performance test. Major (M) – This rating has been given to any item which is very important to the general safety of personnel and the successful completion of the evolution. Should a fire fighter fail to perform any three items rated as Major (M), the fire fighter would be unsuccessful in attaining the required proficiency level for that performance test. General – This rating although there is not symbol, has been given to all remaining items that in combination are relevant to the successful completion of the evolution. Should a fire fighter fail to perform any four items rated as General, the fire fighter would be unsuccessful in attaining the required proficiency level for that performance test. Should a fire fighter fail to perform any combination of Major or General rated items resulting in a sum total of four, the fire fighter would be unsuccessful in attaining the required proficiency level for that performance test.
Contents
v
SKILLS TEST 1 – Pre-Operations Station .................................................................... 1
Performance Test Summary Sheet ........................................................................................ 1 Objectives: NFPA Standard 1002, Chapter 4, Paragraphs 4.2.1, 4.2.2, 4.3.1, 4.3.2,
4.3.3, 4.3.4, 4.3.5, 4.3.6 and 4.3.7 NFPA Standard 1002,Chapter 9, Paragraphs 9.1.1, 9.1.2, 9.1.3, 9.1.4, 9.2.2 and 9.2.3 ........................................................................................................ 1
Performance Test Item – Inspections .................................................................................... 2 Objectives: NFPA Standard 1002, Chapter 4, Paragraphs 4.2.1, 4.2.2 and 4.3.7
NFPA Standard 1002, Chapter 9, Paragraph 9.1.1 ................................................ 2
Performance Test Item – Agent Delivery System ................................................................ 8 Objectives: NFPA Standard 1002, Chapter 9, Paragraph 9.1.1 ................................................ 8
Performance Test Item – Cooling/Winterization Systems ................................................ 10 Objectives: NFPA Standard 1002, Chapter 4, Paragraph 4.2.1
NFPA Standard 1002, Chapter 9, Paragraph 9.1.1 .............................................. 10
Performance Test Item – Apparatus Gauges ..................................................................... 12 Objectives: NFPA Standard 1002, Chapter 4, Paragraphs 4.2.1, 4.3.1, 4.3.2, 4.3.3,
4.3.4, 4.3.5, 4.3.6 and 4.3.7 NFPA Standard 1002, Chapter 9, Paragraphs 9.1.2, 9.1.3, 9.1.4, 9.2.2 and 9.2.3 ............................................................................................................... 12
Performance Test Item – Apparatus Dimensions .............................................................. 14 Objectives: NFPA Standard 1002, Chapter 4, Paragraphs 4.3.1, 4.3.2, 4.3.3, 4.3.4,
4.3.5 and 4.3.6 NFPA Standard 1002, Chapter 9, Paragraph 9.1.2 .............................................. 14
SKILLS TEST 2 - Driving Station .................................................................................. 16
Performance Test Summary Sheet ...................................................................................... 16 Objectives: NFPA Standard 1002, Chapter 4, Paragraphs 4.3.1, 4.3.2, 4.3.3, 4.3.4,
4.3.5 and 4.3.6 NFPA Standard 1002, Chapter 9, Paragraphs 9.1.2, 9.1.3 and 9.1.4 ................... 16
Performance Test Item – Passenger Restraint Devices ..................................................... 17 Objectives: NFPA Standard 1002, Chapter 4, Paragraph 4.3.1
NFPA Standard 1002, Chapter 9, Paragraph 9.1.2 .............................................. 17
Performance Test Item – Pre-Determined Driving Course .............................................. 19 Objectives: NFPA Standard 1002, Chapter 4, Paragraphs 4.3.2, 4.3.3, 4.3.4, 4.3.5
and 4.3.6 NFPA Standard 1002, Chapter 9, Paragraph 9.1.2 .............................................. 19
Contents
vi
Driving Course Specifications .............................................................................................. 27 Driving Course Points........................................................................................................... 28 Driving Course Scorecard .................................................................................................... 28 Penalty Point Chart .............................................................................................................. 29
Performance Test Item – Flightline Driving ...................................................................... 30 Objective: NFPA Standard 1002, Chapter 9, Paragraph, 9.1.3............................................... 30
Performance Test Item – Off Road Conditions ................................................................. 32 Objective: NFPA Standard 1002, Chapter 9, Paragraph 9.1.4................................................ 32
SKILLS TEST 3 - Operations Station ........................................................................... 35
Performance Test Summary Sheet ...................................................................................... 35 Objectives: NFPA Standard 1002, Chapter 9, Paragraphs 9.2.1, 9.2.2 and 9.2.3 ................... 35
Performance Test Item – Apparatus Maneuvering/Positioning ....................................... 36 Objectives: NFPA Standard 1002, Chapter 9, Paragraph 9.2.1 .............................................. 36
Performance Test Item – Apparatus Modulation .............................................................. 39 Objective: NFPA Standard 1002, Chapter 9, Paragraph 9.2.2................................................ 39
Performance Test Item – Apparatus Turret Operations .................................................. 41 Objective: NFPA Standard 1002, Chapter 9, Paragraph 9.2.3................................................ 41
Driver/Operator - Aircraft Rescue and Fire Fighting Performance Test Record .......... 44
1. Pre-Operations
Driver/Operator - ARFF Performance Test 1
SKILLS TEST 1 – Pre-Operations Station Performance Test Summary Sheet Objectives: NFPA Standard 1002, Chapter 4, Paragraphs 4.2.1, 4.2.2, 4.3.1, 4.3.2, 4.3.3,
4.3.4, 4.3.5, 4.3.6 and 4.3.7 NFPA Standard 1002, Chapter 9, Paragraphs 9.1.1, 9.1.2, 9.1.3, 9.1.4, 9.2.2 and 9.2.3
Tasks: 1. Demonstrate the use of inspection forms and other documentation.
2. Explain the recording and reporting of all servicing functions and demonstrate the performance of routine tests, inspections, and servicing functions on an Aircraft Rescue and Fire Fighting (ARFF) apparatus.
3. Explain the operating principles of the agent delivery system and identify its
major components. 4. Explain the auxiliary cooling system and/or demonstrate the winterization
system, if so equipped. 5. Identify and explain the use of the automotive gauges. 6. Explain in common measurements the basic measured specifications of the
ARFF.
1. Pre-Operations
2 Driver/Operator - ARFF Performance Test
Performance Test Item – Inspections Personnel Driver/Operator - Aircraft Rescue and Fire Fighting Classification: Objectives: NFPA Standard 1002, Chapter 4, Paragraphs 4.2.1, 4.2.2 and 4.3.7 NFPA Standard 1002, Chapter 9, Paragraph 9.1.1 Tasks: 1. Demonstrate the use of inspection forms and other documentation.
2. Explain the recording and reporting of all servicing functions and
demonstrate the performance of routine tests, inspections, and servicing functions on an ARFF apparatus.
Evaluator Option: The evaluator will select one discrepancy from each of the inspection
items listed in elements 4 a-g. The discrepancy selected must be at a level a driver/operator would be expected to perform based on local policies governing driver/operator responsibilities.
Setting: Fire department vehicle stalls, ramps or training areas. Tools Fire department aircraft rescue and fire fighting apparatus, local Equipment: service records, forms and apparatus history card. Attainment Successfully complete all elements/steps within 60 minutes. Standard:
1. Pre-Operations
Driver/Operator - ARFF Performance Test 3
Elements/Steps Standards Yes No 1. Identify and explain the
use of the fire apparatus record (if applicable).
1. In accordance with IFSTA Aircraft Rescue and Fire Fighting and IFSTA Pumping Apparatus Driver/Operator Handbook.
A. Kept track of vital information such as
the pump and engine make and capacities
______
______
2. Identify and explain the use of the history record (if applicable).
2. In accordance with IFSTA Aircraft Rescue and Fire Fighting and IFSTA Pumping Apparatus Driver/Operator Handbook.
A. Recorded basic service information
including condition of the truck body, pump, engine hours, road mileage, etc.
______
______
3. Identify and explain the use of the fire apparatus maintenance and inspection forms (In addition to the following, checklists and inspections in the applicable technical order must be accomplished).
3. In accordance with IFSTA Aircraft Rescue and Fire Fighting and IFSTA Pumping Apparatus Driver/Operator Handbook.
A. Identified and explained the use of fire
apparatus maintenance and inspection forms
______
______
4. Demonstrate the procedure for inspecting all apparatus components.
A. Inside driver
compartment B. Outside the apparatus C. Engine compartment D. Fire pump E. Agent tank(s) F. Tools and equipment G. Aircraft rescue and fire
fighting operational readiness
4. In accordance with IFSTA Aircraft Rescue and Fire Fighting and IFSTA Pumping Apparatus Driver/Operator Handbook.
A. Inside driver compartment
1. Checked all apparatus controls and gauges
2. Checked fuel levels and filled as needed
3. Checked all interior lights 4. Checked the horn 5. Checked the mirrors 6. Checked the public address system
and radio 7. Checked audible and visual warning
devices
______
______ ______ ______ ______
______
______
______
______ ______ ______ ______
______
______
1. Pre-Operations
4 Driver/Operator - ARFF Performance Test
Elements/Steps Standards Yes No 8. Tested brake pressure by operating
foot pedal 9. Checked the windshield wipers 10. Checked the map case 11. Inspected seats for tears and
adjustability 12. Checked seatbelts for operation and
wear 13. Checked emergency and parking
brakes 14. Checked circuit breakers and/or
fuses (if applicable) 15. Checked steering wheel adjustment
and reaction 16. Checked heater/air conditioner
operation 17. Checked clutch pedal (if applicable) 18. Checked pressure in all SCBA
cylinders 19. Examined SCBA regulators and
face pieces 20. Checked all hand lights 21. Checked turrets 22. (M) Checked communication
systems
______ ______ ______
______
______
______
______
______
______ ______
______
______ ______ ______
______
______ ______ ______
______
______
______
______
______
______ ______
______
______ ______ ______
______
A. Inside driver compartment B. Outside the apparatus C. Engine compartment D. Fire pump E. Agent tank(s) F. Tools and equipment G. Aircraft rescue and fire
fighting operational readiness
B. Outside the apparatus 1. Checked the truck body for rust,
dents, or exposed areas needing touch-up paint
2. Checked tires for proper inflation 3. Checked wheel lugs for tightness 4. Checked all exterior lights for
operation and damage 5. Checked circuit breakers and/or fuses 6. Checked weather seals around the
cab and compartment doors for looseness, damage and deterioration
7. Inspected windows for cracks or discoloration
8. Checked battery terminals and cleaned as needed
9. Checked battery cables for loose connections
______ ______ ______
______ ______
______
______
______
______
______ ______ ______
______ ______
______
______
______
______
1. Pre-Operations
Driver/Operator - ARFF Performance Test 5
Elements/Steps Standards Yes No 10. Checked electrolyte level and added
water as needed 11. Checked for fuel or oil leaks
______ ______
______ ______
A. Inside driver compartment B. Outside the apparatus C. Engine compartment D. Fire pump E. Agent tank(s) F. Tools and equipment G. Aircraft rescue and fire
fighting operational readiness
C. Engine compartment 1. Checked all drive belts for wear or
defects; adjusted as needed 2. Checked coolant overflow reservoir
for leaks and filled as needed 3. Checked the cooling fan, cooling
system hoses, and the radiator 4. Checked coolant level, color, and
cleanliness and filled, if necessary 5. Checked all oil levels; checked for
leaks on the engine and drive train 6. Checked all hydraulic fluid levels;
checked for leaks 7. Checked brake/master cylinder fluid
level and filled it as needed (if applicable)
8. Checked power steering reservoir and filled it as needed (if applicable)
9. Checked the automatic transmission fluid level, both cold and hot
10. Checked the air filter restriction gauge
11. Checked the windshield washer fluid level
12. Checked any exposed wiring for breaks, loose connections, and insulation frays
13. Checked the emergency shutdown for proper operation
14. Checked the exhaust system for leaks and damage
15. Checked the air system for leaks with the air system and the engine shut off
16. Checked the fuel filter for fuel/water separation and leaks/damage
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
1. Pre-Operations
6 Driver/Operator - ARFF Performance Test
Elements/Steps Standards Yes No A. Inside driver compartment B. Outside the apparatus C. Engine compartment D. Fire pump E. Agent tank(s) F. Tools and equipment G. Aircraft rescue and fire
fighting operational readiness
D. Fire pump 1. Opened all pump drains and flushed
sediment 2. Checked and cleaned intake strainers 3. Operated all valves (if applicable) 4. Checked all panel instruments for
proper operation (if applicable) 5. Operated winterization system (if
applicable) 6. Corrected discrepancies IAW local
policies and procedures
______ ______ ______
______
______
______
______ ______ ______
______
______
______
A. Inside driver compartment B. Outside the apparatus C. Engine compartment D. Fire pump E. Agent tank(s) F. Tools and equipment G. Aircraft rescue and fire
fighting operational readiness
E. Agent tank(s) 1. Filled agent tank(s) to capacity, if
necessary (water, foam, dry chemical)
2. Checked condition of dry chemical agent (if applicable)
3. Checked inside surface for corrosion and cleanliness
4. Checked agent tank(s) for leaks 5. Checked other systems (as
applicable), such as secondary extinguishing systems
6. Corrected discrepancies IAW local policies and procedures
______
______
______ ______
______
______
______
______
______ ______
______
______
A. Inside driver compartment B. Outside the apparatus C. Engine compartment D. Fire pump E. Agent tank(s) F. Tools and equipment G. Aircraft rescue and fire
fighting operational readiness
F. Tools and equipment 1. Checked portable fire extinguishers 2. Checked hose loads for correct
finishes 3. Inventoried all nozzles and
appliances 4. Checked and operated all power
tools 5. Checked all hand tools 6. Checked all ground ladders (if
applicable) 7. Checked condition and pressure of
nitrogen cylinder (if applicable) 8. Corrected discrepancies IAW local
policies and procedures
______
______
______
______ ______
______
______
______
______
______
______
______ ______
______
______
______
1. Pre-Operations
Driver/Operator - ARFF Performance Test 7
Elements/Steps Standards Yes No A. Inside driver compartment B. Outside the apparatus C. Engine compartment D. Fire pump E. Agent tank(s) F. Tools and equipment G. Aircraft rescue and fire
fighting operational readiness
G. Aircraft rescue and fire fighting
operational readiness inspection in accordance with manufacturers recommendations
1. (M) Checked breathing air systems 2. Checked other systems as applicable
(i.e. central tire inflation system, foam transfer pump, dry chemical, etc.)
3. Corrected discrepancies IAW local policies and procedures
______
______
______
______
______
______
1. Pre-Operations
8 Driver/Operator - ARFF Performance Test
Performance Test Item – Agent Delivery System Personnel Driver/Operator - Aircraft Rescue and Fire Fighting Classification: Objectives: NFPA Standard 1002, Chapter 9, Paragraph 9.1.1 Task: Given the operating principles, name the major components, and trace the
direction of agent(s) through the system. Setting: Training ground. Tools ARFF apparatus and diagram of agent delivery system. Equipment: Attainment Successfully complete all elements/steps within 5 minutes. Standard:
1. Pre-Operations
Driver/Operator - ARFF Performance Test 9
Elements/Steps Standards Yes No 1. Give the operating
principles.
1. In accordance with IFSTA Aircraft Rescue and Fire Fighting, IFSTA Pumping Apparatus Driver/Operator Handbook, and the applicable Technical Manual.
A. Explained the principles behind the
operation of the agent delivery system on the ARFF apparatus
______
______
2. Name the major components:
A. Water tank B. Foam tank C. Discharges D. Agent pump E. Foam proportioning
system
2. In accordance with IFSTA Aircraft Rescue and Fire Fighting, IFSTA Pumping Apparatus Driver/Operator Handbook, and the applicable Technical Manual.
A. Identified the water tank B. Identified the foam tank C. Identified discharges D. Identified the agent pump E. Identified the foam proportioning
system
______ ______ ______ ______
______
______ ______ ______ ______
______
3. Trace the flow of agent
from the agent tank to the roof turret.
3. In accordance with IFSTA Aircraft Rescue and Fire Fighting, IFSTA Pumping Apparatus Driver/Operator Handbook, and the applicable Technical Manual.
A. Traced the flow of agent through
pumping system
______
______
1. Pre-Operations
10 Driver/Operator - ARFF Performance Test
Performance Test Item – Cooling/Winterization Systems Personnel Driver/Operator - Aircraft Rescue and Fire Fighting Classification: Objectives: NFPA Standard 1002, Chapter 4, Paragraph 4.2.1 NFPA Standard 1002, Chapter 9, Paragraph 9.1.1 Task: Explain the auxiliary cooling system and/or demonstrate the winterization
system. Setting: Training ground. Tools ARFF apparatus. Equipment: Attainment Successfully complete all elements/steps within 15 minutes. Standard:
1. Pre-Operations
Driver/Operator - ARFF Performance Test 11
Elements/Steps Standards Yes No 1. Explain the auxiliary
cooling system.
1. In accordance with Technical Manual: Aircraft Crash and Structural Fire Fighting Truck.
A. Explained how the thermostat
regulates the hot coolant flow from the engine to the radiator.
______
______
2. Demonstrate the winterization system (if so equipped).
2. In accordance with Technical Manual: Aircraft Crash and Structural Fire Fighting Truck.
A. Located the winterization control on
the dash panel and engaged the system B. Ran the system using all power sources
available battery, engine, and/or external power source
C. If ignition did not occur on the first try, checked the circuit breakers in the heater compartment and reset the breakers
______
______
______
______
______
______
1. Pre-Operations
12 Driver/Operator - ARFF Performance Test
Performance Test Item – Apparatus Gauges Personnel Driver/Operator - Aircraft Rescue and Fire Fighting Classification: Objectives: NFPA Standard 1002, Chapter 4, Paragraphs 4.2.1, 4.3.1, 4.3.2, 4.3.3,
4.3.4, 4.3.5, 4.3.6 and 4.3.7 NFPA Standard 1002, Chapter 9, Paragraphs 9.1.2, 9.1.3, 9.1.4, 9.2.2 and 9.2.3
Task: Identify and explain the use of the following automotive gauges. Identify
potential performance problems based upon gauge readings.
a. Speedometer b. Tachometer c. Oil pressure gauge d. Ammeter e. Voltmeter f. Air pressure gauge g. Water temperature gauge h. Fuel gauge i. Water/foam tank level gauges j. Agent discharge pressure gauge
Setting: Training ground. Tools ARFF apparatus. Equipment: Attainment Successfully complete all elements/steps within 15 minutes. Standard:
1. Pre-Operations
Driver/Operator - ARFF Performance Test 13
Elements/Steps Standards Yes No 1. Identify and explain the
use of automotive gauges.
1. In accordance with IFSTA Aircraft Rescue and Fire Fighting, IFSTA Pumping Apparatus Driver/Operator Handbook, and applicable Technical Manual specifications.
A. Explained that the speedometer
measures apparatus speed B. Explained that the tachometer
measures rpm of the engine C. Explained that the oil pressure gauge
measures engine oil pressure D. Explained that the ammeter measures
the amount of current drawn from the battery to operate electrical equipment or the amount of current being supplied to the battery to charge it
E. Explained that the voltmeter indicates battery condition
F. Explained that the air pressure gauge measures the air systems pressure
G. Explained that the water temperature gauge measures coolant temperature in the engine
H. Explained that the fuel gauge measures fuel in the tank
I. Explained that the water/foam tank level gauges measure available agent in the perspective tank
J. Explained that the agent discharge pressure gauge measures discharge pressure
K. Identified potential performance problem based upon gauge reading – Evaluator Option
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
______
1. Pre-Operations
14 Driver/Operator - ARFF Performance Test
Performance Test Item – Apparatus Dimensions Personnel Driver/Operator - Aircraft Rescue and Fire Fighting Classification: Objectives: NFPA Standard 1002, Chapter 4, Paragraphs 4.3.1, 4.3.2, 4.3.3, 4.3.4,
4.3.5 and 4.3.6 NFPA Standard 1002, Chapter 9, Paragraph 9.1.2
Task: Explain in common measurements the basic dimensions of the apparatus
and the turning radius. Setting: Training ground. Tools ARFF apparatus. Equipment: Attainment Successfully complete all elements/steps within 15 minutes. Standard:
1. Pre-Operations
Driver/Operator - ARFF Performance Test 15
Elements/Steps Standards Yes No 1. Identify common
measurements.
1. In accordance with Technical Manual: Aircraft Crash and Structural Fire Fighting Truck.
Note: Use measurements for local apparatus used in the performance test.
A. Identified the apparatus height B. Identified the apparatus weight
- with agent - without agent
C. Identified the apparatus width D. Identified the apparatus length E. Identified the apparatus ground
clearance F. Identified the apparatus turning radius
______
______ ______ ______ ______
______ ______
______
______ ______ ______ ______
______ ______
2. Driving
16 Driver/Operator - ARFF Performance Test
SKILLS TEST 2 -Driving Station Performance Test Summary Sheet Objectives: NFPA Standard 1002, Chapter 4, Paragraphs 4.3.1, 4.3.2, 4.3.3, 4.3.4, 4.3.5
and 4.3.6 NFPA Standard 1002, Chapter 9, Paragraphs 9.1.2, 9.1.3 and 9.1.4
Tasks: 1. Demonstrate the safe use of apparatus and of passenger seatbelts.
2. Drive a fire department ARFF apparatus. 3. Demonstrate the ability to drive on the airfield/flightline on improved surfaces:
a. Drive on an aircraft ramp (day and night) b. Drive on a taxiway (day and night) c. Drive on a runway (day and night)
4. Demonstrate the ability to drive in off road conditions:
a. Loose soil or sand b. Wet soil or sand c. Forward on a grade of 30° d. Downward on a grade of 30° e. Side to side on a grade of 20° f. Reduced sight g. Undercarriage obstacle
2. Driving
Driver/Operator - ARFF Performance Test 17
Performance Test Item – Passenger Restraint Devices Personnel Driver/Operator - Aircraft Rescue and Fire Fighting Classification: Objectives: NFPA Standard 1002, Chapter 4, Paragraph 4.3.1 NFPA Standard 1002, Chapter 9, Paragraph 9.1.2 Task: Demonstrate the safe use of apparatus and of passenger seatbelts. Setting: Training ground. Tools ARFF apparatus. Equipment: Attainment Successfully complete all elements/steps within 5 minutes. Standard:
2. Driving
18 Driver/Operator - ARFF Performance Test
Elements/Steps Standards Yes No 1. Demonstrate the safe use
of apparatus and of passenger seatbelts.
1. In accordance with IFSTA Aircraft Rescue and Fire Fighting, IFSTA Pumping Apparatus Driver/Operator Handbook, and state, local and installation procedures.
A. (C) Correctly secured passenger
seatbelts prior to starting apparatus B. (C) Ensured all personnel on the
apparatus used the seatbelts correctly C. Obeyed all traffic regulations
1. (C) Used all applicable warning devices
2. (M) Ensured safety at intersections 3. Properly followed the right of way
laws D. Demonstrated responsibility and
concern for safety of apparatus and personnel while driving apparatus
1. (M) Adjusted speed for weather conditions 2. (M) Adjusted stopping distances 3. Gradually slowed down by applying
steady, even pressure to the brake pedal
E. When braking - stopped smoothly
1. Avoided skidding situations 2. Compensated for apparatus weight
______
______ ______
______ ______
______
______ ______
______
______ ______
______
______ ______
______ ______
______
______ ______
______
______ ______
2. Driving
Driver/Operator - ARFF Performance Test 19
Performance Test Item – Pre-Determined Driving Course Personnel Driver/Operator - Aircraft Rescue and Fire Fighting Classification: Objectives: NFPA Standard 1002, Chapter 4, Paragraphs 4.3.2, 4.3.3, 4.3.4, 4.3.5
and 4.3.6 NFPA Standard 1002, Chapter 9, Paragraph 9.1.2
Task: Drive a Fire Department ARFF apparatus. Setting: Predetermined driving course, fire department training ground or other
suitable area for driving course set up. Tools ARFF apparatus, cones, ruler and scorecard. Equipment: Attainment Completion of all elements/steps within 30 minutes. Standard:
2. Driving
20 Driver/Operator - ARFF Performance Test
Elements/Steps Standards Yes No 1. Drive a predetermined
course.
1. In accordance with NFPA 1002: Fire Apparatus Driver/Operator Professional Qualifications, IFSTA Aircraft Rescue and Fire Fighting, and IFSTA Pumping Apparatus Driver/Operator Handbook.
A. Made 4 left turns
1. Activated the left signal turn 2. Checked the side and rear view
mirrors 3. Moved the vehicle to left lane when
necessary 4. Checked for oncoming traffic 5. Checked to see if side street or road
is clear 6. Made safe left turns
B. Made 4 right turns
1. Activated the right turn signal 2. Checked the side and rear view
mirrors 3. Moved the vehicle to right lane when
necessary 4. Checked for oncoming traffic 5. Checked to see if side street or road
is clear 6. Made safe right turns
C. Drove straight section of road or
highway
1. Maintained vehicle speed 2. Checked for oncoming traffic 3. Checked side and rear view mirrors 4. Checked side streets or roads
D. Passed through one intersection
1. Approached the intersection with
caution 2. Checked traffic – left, right, and left
again
______
______
______ ______
______ ______
______
______
______ ______
______ ______
______ ______ ______ ______
______
______
______
______
______ ______
______ ______
______
______
______ ______
______ ______
______ ______ ______ ______
______
______
2. Driving
Driver/Operator - ARFF Performance Test 21
Elements/Steps Standards Yes No 3. Safely proceeded through the
intersection
E. Passed through two intersections with required stops
1. Approached the intersection with
caution 2. Brought the vehicle to a complete
stop 3. Checked traffic – left, right, and left
again 4. Safely proceeded through the
intersection
F. Railroad crossing
1. Approached the railroad crossing with caution
2. Checked the tracks – left and right 3. Stopped when necessary 4. Proceeded across tracks when safe to
do so
G. Curve in highway – right or left
1. Slowed down the vehicle before entering curve
2. Adjusted the speed as required 3. Maintained safe control of vehicle
H. Entered limited access highway
1. Checked traffic while on the entrance
ramp 2. Adjusted the speed of the vehicle to
match flow of traffic 3. Activated the turn signal 4. Checked the side and rear view
mirrors 5. Moved the vehicle from acceleration
lane to the highway safely
______
______
______
______
______
______ ______ ______
______
______ ______ ______
______
______ ______
______
______
_____
______
______
______
______
______ ______ ______
______
______ ______ ______
______
______ ______
______
______
2. Driving
22 Driver/Operator - ARFF Performance Test
Elements/Steps Standards Yes No I. Changed 2 lanes on limited access
Highway
1. Activated the turn signal 2. Checked the side and rear view
mirrors 3. Safely completed the lane change
J. Exited limited access highway
1. Activated the turn signal 2. Checked the side and rear view
mirrors 3. Safely completed the lane change 4. Activated the turn signal when the
exit was in sight 5. Moved the vehicle into the
deceleration lane 6. Slowed down the vehicle and exited
safely
K. Downgrade
1. Downshifted before entering the grade
2. Made sure the vehicle remained in gear
3. Properly used brakes and lower gears 4. Limited engine rpm – below redline
L. Upgrade
1. Did not allow engine rpm to drop
below minimum 2. Automatic transmission downshifted
automatically 3. Downshifted standard transmission
to maintain engine rpm and speed
M. Underpass or low clearance 1. Approached with caution 2. Checked to see if underpass height
was marked
______
______ ______
______
______ ______
______
______
______
______
______ ______ ______
______
______
______
______
______
______
______ ______
______
______ ______
______
______
______
______
______ ______ ______
______
______
______
______
______
2. Driving
Driver/Operator - ARFF Performance Test 23
Elements/Steps Standards Yes No 3. Stopped and looked if height was not
marked 4. Proceeded only when sure it was safe
to do so
______
______
______
______
2. Back vehicle into a
restricted space (alley dock exercise).
2. In accordance with NFPA 1002: Fire Apparatus Driver/Operator Professional Qualifications, IFSTA Aircraft Rescue and Fire Fighting, and IFSTA Pumping Apparatus Driver/Operator Handbook.
A. Passed the "barricades" marking the
loading dock on the left. B. Backed apparatus by a left turn into the
marked loading dock C. Came to a complete stop in a smooth
and safe manner D. Stopped where and when directed E. Used spotters when backing F. Completed exercise without pulling
forward G. Completed exercise without striking
obstructions H. Repeated steps A through G with the
loading dock on the right
______
______
______ ______ ______
______
______
______
______
______
______ ______ ______
______
______
______
3. Maneuver around obstacles
(serpentine exercise).
3. In accordance with NFPA 1002: Fire Apparatus Driver/Operator Professional Qualifications, IFSTA Aircraft Rescue and Fire Fighting, and IFSTA Pumping Apparatus Driver/Operator Handbook.
A. Drove the apparatus along the left side
of the markers in a straight line and stopped just beyond the last barrel/cone
B. Backed the apparatus between the markers by passing to the left of #1, to the right of #2, and to the left of #3 and stopped beyond the last barrel/cone using spotters
C. Drove the vehicle forward and to the right of #3, left of #2, and right of #1
______
______
______
______
______
______
2. Driving
24 Driver/Operator - ARFF Performance Test
Elements/Steps Standards Yes No 4. Turn vehicle 180 degrees
(confined space turn-around).
4. In accordance with NFPA 1002: Fire Apparatus Driver/Operator Professional Qualifications, IFSTA Aircraft Rescue and Fire Fighting, and IFSTA Pumping Apparatus Driver/Operator Handbook.
A. Pulled into a designated area through
opening B. Made a U-turn by maneuvering vehicle C. Backed up at least once using spotters D. Exited the area through the same
______ ______ ______ ______
______ ______ ______ ______
5. Diminishing clearance
horizontal and vertical clearances.
5. In accordance with NFPA 1002: Fire Apparatus Driver/Operator Professional Qualifications, IFSTA Aircraft Rescue and Fire Fighting, and IFSTA Pumping Apparatus Driver/Operator Handbook.
A. Proceeded from the wide to the narrow
end B. Did not touch markers C. Stopped with the front bumper on the
finish line (Rear bumper for driving in reverse)
D. Came to a complete stop in a smooth and safe manner
E. Stopped when and where directed F. Stopped vehicle before striking
crossbar G. Repeated steps A through F in reverse
with spotters
______ ______
______
______ ______
______
______
______ ______
______
______ ______
______
______
6. Defensive driving
techniques: A. Adhered to all traffic
regulations B. Fastened seat belts C. Operated vehicle safely D. Lane changes E. Straight line vehicle
positioning
6. In accordance with NFPA 1002: Fire Apparatus Driver/Operator Professional Qualifications and IFSTA Pumping Apparatus Driver/Operator Handbook.
A. Adhered to all traffic regulations
1. (C) Used all warning devices 2. (M) Ensured safety at intersections 3. Properly followed the right of way
laws
______ ______
______
______ ______
______
2. Driving
Driver/Operator - ARFF Performance Test 25
Elements/Steps Standards Yes No A. Adhered to all traffic
regulations B. Fastened seat belts C. Operated vehicle safely D. Lane changes E. Straight line vehicle
positioning
B. (C) Fastened seat belt upon entering
the vehicle
______
______
A. Adhered to all traffic regulations
B. Fastened seat belts C. Operated vehicle safely D. Lane changes E. Straight line vehicle
positioning
C. Operated vehicle safely
1. Demonstrated responsibility and concern for safety of apparatus and personnel while driving apparatus
2. (M) Adjusted speed for weather conditions
3. (M) Adjusted stopping distances 4. Slowed gradually 5. Ensured all personnel wear seatbelts 6. Braking – stopped smoothly
a. Avoided skidding situations b. Compensated for vehicle weight
shifting
7. Spotted apparatus at curb and out of traffic lane
8. Maintained vehicle control while backing
a. Used spotters
______
______ ______ ______ ______
______
______
______
______
______
______
______ ______ ______ ______
______
______
______
______
______
A. Adhered to all traffic regulations
B. Fastened seat belts C. Operated vehicle safely D. Lane changes E. Straight line vehicle
positioning
D. Lane changes
1. Approached the first lane at a safe speed
2. Followed flash card directions 3. Drove in the designated lane
______ ______ ______
______ ______ ______
A. Adhered to all traffic regulations
B. Fastened seat belts C. Operated vehicle safely D. Lane changes E. Straight line vehicle
E. Straight line vehicle positioning
1. Traveled in a forward direction without weaving
2. Accelerated through gears without stopping
______
______
______
______
2. Driving
26 Driver/Operator - ARFF Performance Test
Elements/Steps Standards Yes No positioning
3. Did not touch markers 4. Came to a complete stop in a smooth
and safe manner 5. Stopped with the front bumper on the
finish line (Rear bumper for driving in reverse)
6. Stopped when and where directed 7. Repeated steps 1 through 6 in reverse
with spotters
______
______
______ ______
______
______
______
______ ______
______
7. Operate vehicle equipment
7. IAW manufactures data, checklist, or other applicable information.
A. Donned appropriate safety gear B. Checked all components of the
equipment C. Started equipment (if applicable) D. Operated equipment within
manufactures specifications E. Shut equipment down (if applicable) F. Stored equipment using proper
procedures
______
______ ______
______ ______
______
______
______ ______
______ ______
______
2. Driving
Driver/Operator - ARFF Performance Test 27
Driving Course Specifications
Utilize this sheet to design your driving course in relation to the vehicles you have assigned. Please set up your course per calculations outlined below.
Key
VW = Vehicle Width VL = Vehicle Length
ft = feet
Exercise Dimensions Alley Dock Depth of Dock: VL plus 3 ft
Width of Dock: VW plus 2 ft Wall distance from Dock entrance: VL multiplied by 1.48
Serpentine Distance between cones: VL multiplied by 1.25 Confined Space Turnaround
Entrance Width: VW plus 4 ft Width of Space: VL multiplied by 1.85 Length of Space: VL multiplied by 3.7
Diminishing Clearance Wide Entrance: VW plus 1.5 ft Narrow Point: VW plus 2 inches
Lane Change Width of Lanes: VW plus 2 ft Length of Lanes: VL multiplied by 1.85 Distance between lanes: VL multiplied by 1.11
Straight Line Positioning
Width of Lane: VW plus 4 ft Length of Lane: VL multiplied by 7.4 (e.g. VL is 47 ft; 47 X 7.4 = 348 ft)
2. Driving
28 Driver/Operator - ARFF Performance Test
Driving Course Points
Type of Vehicle Total Possible Points Minimum Passing Score Pumpers 450 360 Aerials/Tillers 450 360 ARFF Apparatus 450 360 Mobile Water Supply 450 360
Driving Course Scorecard
OBSTACLE PENALTY POINTS
PENALTY POINTS
PENALTY POINTS
PENALTY POINTS
PENALTY POINTS
PENALTY POINTS
Candidate’s Name:
Alley Dock
Serpentine
180º Turnaround
Diminishing Clearance
Lane Change
Straight Line
Total Possible Points 450 450 450 450 450 450
Total Penalty Points
Score
Minimum Passing Score
Pass/Fail
2. Driving
Driver/Operator - ARFF Performance Test 29
PENALTY POINT CHART
DESCRIPTION ERROR PENALTY POINTS
Alley dock (100 pts)
Distance from rear bumper to finish line 0 - 6 inches 6 - 9 inches
9 - 12 inches 12 - 15 inches 15 - 18 inches
18 or more inches Each marker brushed, moved or overturned
0 5
10 15 20 50 5
Serpentine (50 pts)
Each marker brushed, moved or overturned Passing course marker on the wrong side Each time vehicle stops during the exercise
5 5 5
180º Turnaround (50 pts)
Each marker brushed, moved or overturned Failure to maintain constant motion or if vehicle stops
5
5
Diminishing clearance (100 pts)
Distance from front/rear bumper to finish line (Use the following criteria for both forward and reverse movement)
0 - 6 inches 6 - 9 inches
9 - 12 inches 12 - 15 inches 15 - 18 inches
18 or more inches Each marker brushed, moved or overturned Vertical bar struck
0 5
10 15 20 50 5 25
Lane change (50 pts)
Failure to maintain a safe operating speed Each marker brushed, moved or overturned Each time the apparatus stops during the exercise Failure to take the lane marked by judges Failure to maintain control of apparatus
10 5
25 25 50
Straight line (100 pts)
Failure to maintain constant motion or if apparatus stops Each marker brushed, moved or overturned Forward/Reverse – Distance from rear/front bumper to finish line
0 - 6 inches 6 - 9 inches
9 - 12 inches 12 - 15 inches 15 - 18 inches
18 or more inches Each marker brushed, moved or overturned
25 5
0 5
10 15 20 50 5
2. Driving
30 Driver/Operator - ARFF Performance Test
Performance Test Item – Flightline Driving Personnel Driver/Operator - Aircraft Rescue and Fire Fighting Classification: Objective: NFPA Standard 1002, Chapter 9, Paragraph, 9.1.3 Task: Demonstrate the ability to drive on the airfield/flightline on improved
surfaces:
a. Drive on an aircraft ramp (day and night) b. Drive on a taxiway (day and night) c. Drive on a runway (day and night)
Note: Only the tests that apply to the authority having jurisdiction need be evaluated. The NFPA did not differentiate, in fact, specifically stated that the list in paragraph 4-3.1 of NFPA Standard 1002 be followed. It is understood that a great many of the listed items do not appear on an airfield or flightline and thus should be omitted from the evaluation phase. Where applicable those items that are possible shall be evaluated. The intent of this task is that the potential ARFF Driver/Operator be fully capable of operating the apparatus on the airfield/flightline.
Setting: An area that would accommodate the needs of the tests being conducted in
the local area. Tools ARFF apparatus. Equipment: Attainment Successful completion of all elements/steps within a safe period of Standard: time following all of the state, local and installation polices.
2. Driving
Driver/Operator - ARFF Performance Test 31
Elements/Steps Standards Yes No 1. Demonstrate the ability to
operate on the following surfaces:
A. Aircraft ramp B. Aircraft taxiway C. Aircraft runway
1. In accordance with NFPA 1002: Fire Apparatus Driver/Operator Professional Qualifications, NFPA 1500: Standard on Fire Department Occupational Safety and Health Program, and State, Local and installation guidelines.
A. Aircraft ramp
1. Assured safe speed and distance
around aircraft (A/C) 2. Alert to A/C movement 3. Alert to personnel movement 4. Obtained proper approval prior to
ramp access (if required) 5. Completed items 1-4 during
daylight hours 6. Completed items 1-4 during
darkness (night)
______ ______ ______
______
______
______
______ ______ ______
______
______
______
A. Aircraft ramp B. Aircraft taxiway C. Aircraft runway
B. Aircraft taxiway
1. Assured safe speed 2. Followed instructions from tower,
markings, or other authority having jurisdiction.
3. Completed items 1-2 during daylight hours
4. Completed items 1-2 during darkness (night)
______
______
______
______
______
______
______
______
A. Aircraft ramp B. Aircraft taxiway C. Aircraft runway
C. Aircraft runway
1. Assured safe speed 2. Obtained clearance from tower or
other entity prior to entering runway
3. Maintained contact with the authority having jurisdiction.
4. Notified authority of status when clear of the runway
5. Completed items 1-4 during daylight hours
6. Completed items 1-4 during darkness (night)
______
______
______
______
______
______
______
______
______
______
______
______
2. Driving
32 Driver/Operator - ARFF Performance Test
Performance Test Item – Off Road Conditions Personnel Driver/Operator - Aircraft Rescue and Fire Fighting Classification: Objective: NFPA Standard 1002, Chapter 9, Paragraph 9.1.4 Task: Demonstrate the ability to operate under the conditions listed below,
following state, local and installation polices:
a. Loose soil/sand b. Wet soil/sand c. Grade of 30° forward d. Grade of 30° downward e. Grade of 20o side to side f. Reduced sight g. Undercarriage obstacle
Note: Only the tests that apply to the authority having jurisdiction need be evaluated.
Setting: An area that would accommodate the needs of the tests being conducted in
the local area. Tools ARFF apparatus. Equipment: Attainment Successful completion of all elements/steps within a safe period of Standard: time following all of the state, local and installation polices.
2. Driving
Driver/Operator - ARFF Performance Test 33
Elements/Steps Standards Yes No 1. Drive an ARFF apparatus
on a course that includes the following conditions:
A. Loose soil or sand B. Wet soil or sand C. Forward grade of 30° D. Downward grade of 30° E. Side to side grade of 20o F. Reduced sight G. Undercarriage limits
1. In accordance with NFPA 1002: Fire Apparatus Driver/Operator Professional Qualifications, NFPA 1500: Standard on Fire Department Occupational Safety and Health Program, apparatus Technical Manual, and state, local and installation polices.
A. Loose soil or sand
1. Engaged all wheel drive, if
applicable, prior to entering the area 2. Maintained safe and continued speed
______ ______
______ ______
A. Loose soil or sand B. Wet soil or sand C. Forward grade of 30° D. Downward grade of 30° E. Side to side grade of 20o F. Reduced sight G. Undercarriage limits
B. Wet soil or sand
1. Engaged all wheel drive, if
applicable, prior to entering area 2. Maintained safe and continued speed
C. Forward grade of 30°
1. Maintained safe speed up the grade 2. Continually monitored apparatus’
motion 3. Did not stop while on the grade
D. Downward grade of 30°
1. Maintained safe speed down the
grade 2. Continually monitored apparatus’
motion 3. Did not stop while on the grade
______ ______
______
______ ______
______
______ ______
______ ______
______
______ ______
______
______ ______
A. Loose soil or sand B. Wet soil or sand C. Forward grade of 30° D. Downward grade of 30° E. Side to side grade of 20º F. Reduced sight G. Undercarriage limits
E. Side to side grade of 20º
1. Maintained safe speed 2. Continually monitored of apparatus
indicators
F. Reduced sight
1. Assumed safe speed for driving conditions
______
______
______
______
______
______
2. Driving
34 Driver/Operator - ARFF Performance Test
Elements/Steps Standards Yes No 2. Did not drive beyond sight of control
G. Undercarriage limits
1. Ensured undergrowth is passable 2. Used spotter to check for:
- stumps - rocks - holes
3. Assumed safe speed for driving conditions
______
______
______ ______ ______
______
______
______
______ ______ ______
______
3. Operations
Driver/Operator - ARFF Performance Test 35
SKILLS TEST 3 - Operations Station Performance Test Summary Sheet Objectives: NFPA Standard 1002, Chapter 9, Paragraphs 9.2.1, 9.2.2 and 9.2.3 Tasks: 1. Demonstrate maneuvering, positioning, and repositioning of an ARFF
apparatus considering wind direction, terrain, type of aircraft, cargo, armament and support for the firefighting operation.
2. Demonstrate pump and roll (power modulation) of the ARFF apparatus while
discharging agent at the apparatus’ rated capacity.
3. Position, set up the apparatus, and perform the following operations using the apparatus to ensure a safe operation: discharge agent at the maximum delivery rate from the apparatus water tank through the roof turret, pump at maximum rated capacity from a hydrant, and transfer from an internal to an external water source.
3. Operations
36 Driver/Operator - ARFF Performance Test
Performance Test Item – Apparatus Maneuvering/Positioning Personnel Driver/Operator - Aircraft Rescue and Fire Fighting Classification: Objectives: NFPA Standard 1002, Chapter 9, Paragraph 9.2.1 Task: Demonstrate maneuvering, positioning, and repositioning of an ARFF
apparatus considering wind direction, terrain, type of aircraft, cargo, armament and support for the firefighting operation.
Setting: Training ground. Tools ARFF apparatus and a turret operator. Equipment: Attainment Successful completion of all elements/steps within 30 minutes Standard:
3. Operations
Driver/Operator - ARFF Performance Test 37
Elements/Steps Standards Yes No 1. Maneuver apparatus
towards designated point on Aircraft.
1. In accordance with IFSTA Aircraft Rescue and Fire Fighting, NFPA 1002: Fire Apparatus Driver/Operator Professional Qualifications, NFPA 1500: Standard on Fire Department Occupational Safety and Health Program, pre-fire plans and/or Technical Manual.
A. Referred to applicable pre-fire plan for
specific information concerning hazards, optimum apparatus positioning, approach to entry point, pre-designated rescuer’s duties, and other factors
B. Proceeded on command of evaluator C. Operated ARFF apparatus safely D. Maneuvered turns safely E. Controlled apparatus at all times
______ ______ ______ ______ ______
______ ______ ______ ______ ______
2. Position ARFF apparatus at
designated point according to command.
2. In accordance with IFSTA Aircraft Rescue and Fire Fighting, NFPA 1002: Fire Apparatus Driver/Operator Professional Qualifications, NFPA 1500: Standard on Fire Department Occupational Safety and Health Program, pre-fire plans and/or Technical Manual.
A. Referred to applicable pre-fire plan for
specific information concerning hazards, optimum apparatus positioning, approach to entry point, pre-designated rescuer’s duties, and other factors
B. Considered tactical purpose of aircraft and positioned the apparatus at a 45° angle and away from line of fire of aircraft armaments (if applicable)
______
______
______
______
3. Withdraw apparatus as if munitions have become involved in fire.
3. In accordance with IFSTA Aircraft Rescue and Fire Fighting, NFPA 1002: Fire Apparatus Driver/Operator Professional Qualifications, NFPA 1500: Standard on Fire Department Occupational Safety and Health Program, pre-fire plans and/or Technical Manual.
3. Operations
38 Driver/Operator - ARFF Performance Test
Elements/Steps Standards Yes No
A. Referred to applicable pre-fire plan for specific information concerning hazards, optimum apparatus positioning, approach to entry point, pre-designated rescuer’s duties, and other factors
B. Sounded proper withdrawal signal C. Withdrew safely and promptly D. Assembled at the designated
withdrawal area with the rear of the apparatus facing designated crash point
______ ______ ______
______
______ ______ ______
______
4. Reposition an apparatus for extinguishment and overhaul according to command.
4. In accordance with IFSTA Aircraft Rescue and Fire Fighting, NFPA 1002: Fire Apparatus Driver/Operator Professional Qualifications, NFPA 1500: Standard on Fire Department Occupational Safety and Health Program, pre-fire plans and/or Technical Manual.
A. Referred to applicable pre-fire plan for
specific information concerning hazards, optimum apparatus positioning, approach to entry point, pre-designated rescuer’s duties, and other factors
B. Positioned the ARFF apparatus according to evaluator’s instructions
C. Approached the designated point safely for extinguishment and overhaul
______
______
______
______
______
______
3. Operations
Driver/Operator - ARFF Performance Test 39
Performance Test Item – Apparatus Modulation Personnel Driver/Operator - Aircraft Rescue and Fire Fighting Classification: Objective: NFPA Standard 1002, Chapter 9, Paragraph 9.2.2 Task: Demonstrate pump and roll (power modulation) of the ARFF apparatus
while discharging agent at the apparatus’ rated capacity. Setting: Training ground. Tools ARFF apparatus and a turret operator. Equipment: Attainment Successful completion of all elements/steps within 30 minutes Standard:
3. Operations
40 Driver/Operator - ARFF Performance Test
Elements/Steps Standards Yes No 1. Pump and roll (modulate)
in both forward and reverse while discharging agent.
1. In accordance with IFSTA Aircraft Rescue and Fire Fighting, NFPA 1002: Fire Apparatus Driver/Operator Professional Qualifications, and NFPA 1500: Standard on Fire Department Occupational Safety and Health Program.
A. (M) Proceeded on the command of the
evaluator B. (M) Operated the apparatus safely in a
forward direction C. (M) Maneuvered turns safely D. (M) Ensured engine rpm is at or below
idle, then engage pump. Discharged agent briefly with a short burst at least 1,000 ft from intended target to ensure pump is operational (Note: For the Stryker apparatus do not engage the pump until 300 ft from the intended target.)
E. (M) Interrupted agent flow from discharge until it is within range of the turret
F. (M) Continually discharged agent once apparatus was within range of intended target
G. (M) Brought the apparatus to a complete stop
H. (M) Operated the apparatus safely in reverse for repositioning
I. (M) Discharged agent on the intended target while moving in reverse
J. (M) Brought the apparatus to a complete stop
K. (M) Operated the apparatus safely in forward direction for repositioning
L. (M) Made sure the agent flow was not interrupted during the entire modulation process
M. (M) Controlled the apparatus at all times
______
______ ______
______
______
______
______
______
______
______
______
______
______
______
______ ______
______
______
______
______
______
______
______
______
______
______
3. Operations
Driver/Operator - ARFF Performance Test 41
Performance Test Item – Apparatus Turret Operations Personnel Driver/Operator - Aircraft Rescue and Fire Fighting Classification: Objective: NFPA Standard 1002, Chapter 9, Paragraph 9.2.3 Task: Position, set up the apparatus, and perform the following operations using
the apparatus to ensure a safe operation: discharge agent at the maximum delivery rate from the apparatus water tank through the roof turret, pump at maximum rated capacity from a hydrant, and transfer from an internal to an external water source.
Setting: Training ground, hydrant and/or a draft source. Tools ARFF apparatus, necessary hoses and adapters. Equipment: Attainment Successful completion of all elements/steps within 15 minutes. Standard:
3. Operations
42 Driver/Operator - ARFF Performance Test
Elements/Steps Standards Yes No 1. Position, set up the
apparatus, and perform the following operations:
A. Discharge water at the
maximum delivery rate from the apparatus water tank through the roof turret
B. Resupply operations from
a hydrant C. Resupply operations from
an apparatus
1. In accordance with IFSTA Aircraft Rescue and Fire Fighting, IFSTA Pumping Apparatus Driver/Operator Handbook, and the applicable Technical Manual
A. Discharge water at the maximum
delivery rate from the apparatus water tank through the roof turret.
1. Positioned the ARFF apparatus 2. Engaged the pump 3. Opened the discharge and checked
the gauge for correct pressure 4. Shut down the pump operation 5. Ensured safe operation using proper
apparatus controls
______ ______
______ ______
______
______ ______
______ ______
______
A. Discharge water at the
maximum delivery rate from the apparatus water tank through the roof turret
B. Resupply operations
from a hydrant C. Resupply operations from
an apparatus
B. Resupply operations from a hydrant
1. Selected the best hydrant considering location and size of the water main
2. Properly positioned the ARFF apparatus
3. Engaged the pump 4. Pumped at maximum capacity 5. Opened the water tank lid (if
applicable) 6. Connected ARFF apparatus to a
hydrant 7. Opened hydrant and intake valve 8. Maintained an adequate flow of
agent during the operation 9. Adjusted the discharge based upon
water intake 10. Slowly shut down the operation
______
______ ______ ______
______
______ ______
______
______ ______
______
______ ______ ______
______
______ ______
______
______ ______
A. Discharge water at the
maximum delivery rate from the apparatus water tank through the roof turret
B. Resupply operations from
a hydrant
C. Resupply operations from an apparatus
1. Selected the proper water source
(pumper, mobile water supply apparatus, etc.)
2. Properly positioned the ARFF apparatus
______
______
______
______
3. Operations
Driver/Operator - ARFF Performance Test 43
Elements/Steps Standards Yes No C. Resupply operations
from an apparatus
3. Engaged the pump 4. Opened the discharge 5. Pumped at maximum capacity from
ARFF apparatus 6. Connected the intake lines from
water source 7. Pumped at maximum capacity from
the supply apparatus 8. Opened water tank lid on the ARFF
apparatus if required 9. Maintained an adequate flow of
agent during the operation 10. Adjusted flow (low/high) to
compensate for low intake pressure 11. Maintained safe operation of
apparatus and equipment 12. Slowly shut down the operation
______ ______
______
______
______
______
______
______
______ ______
______ ______
______
______
______
______
______
______
______ ______
Performance Test Record
"FOUO. This document contains information exempt from mandatory disclosure under the FOIA. Exemption 5 U.S.C. 552(b)(6) applies. This information is also protected by the Privacy Act of 1974
and must be safeguarded from unauthorized disclosure."
Driver/Operator - Aircraft Rescue and Fire Fighting INSTRUCTIONS: This form must be completed and kept on file. A copy of this form is also required to be submitted with the candidate’s certification package. Date of Evaluation ______________________ Candidate’s Name____________________________________ SSN ____________________ Evaluator’s Name____________________________________ SSN ____________________ The candidate has PASSED/FAILED the Driver/Operator - Aircraft Rescue and Fire Fighting Performance Tests for the stations marked below:
Performance Test Station Passed Failed
Pre-Operations
Driving
Operations
If candidate has failed the performance evaluation, provide the following information: (Use additional sheets, if necessary) Objective(s): Reason(s) for failure: Candidate Signature _________________________________________________ Evaluator Signature _________________________________________________