Small Engine Parts & Accessories CHAIN SAW ACCESSORIES - O.E.M CHAIN SAW ACCESSORIES - O.E.M C C 605-710 71752 Air Filter Fits ICS Concrete / Cut off Saw models: 603GC, 613GC, 633GC and 680GC. Size: 3-7/8” OD X 2-3/8” ID X 3-1/4” HT. Same as our 605-709 except higher. 605-711 73336 Pre Filter For use with our 605-710 air filter. Fits ICS Concrete / Cut off Saw Size: 2-3/8” bottom OD X 2-1/16” top OD X 2-9/16” HT. 592-106 505375 Crankshaft Bearing Fits ICS concrete saws, Size: 15mm (37/64”) ID X 35mm (1-3/8”) OD X 11mm (7/16”) HT. Bearing# 6202 - open both sides) 593-103 73209 Crankshaft bearing Fits ICS models: 613GC, 633GC and 680GC; Size: 17mm ID X 40mm OD X 12mm HT. (Bearing# 6203/C3) Open both sides. JONSEREDS 605-173 501 80 71-01 501 80 71-05 Air Filter For Chain Saw model: 630 605-062 503 81 45-03 Air Filter For chain saw models: 2063, 2071, 2163 and 2171. Nylon mesh style. Size: 3-5/8” L x 2-7/8” W x 1-5/8” HT. 605-060 537 02 40-03 Air Filter (Twist on) For chain saw models: 2141, 2145, 2149, 2150 and 2152. Air filter attaches by simply twisting on the carburetor manifold. Note: Some 346 and 353 models use a steel snap to connect. 657-120 503 86 92-01 Anti Vibration Damping Fits chain saw models: 2147 and 2152. Measures: 11/16” L X 9/16” OD with a 3/16” ID. 646-154 503 74 44-01 Clutch Assembly For chain saw models: 2063, 2065, 2163, 2165, 2071 & 2171. Measures: 3.057” OD X 0.471” Thick. 646-155 503 70 15-02 Clutch Assembly For chain saw models: 820, 830, 920, 930, 2094 & 2095. Measures: 3.045” OD (77mm) X 0.542” (13.90mm) Thick. 646-113 501 77 85-01 Clutch Assembly Fits chain saw models: 625 & 630 OLDER models. Measures: 3.057” OD X 0.512” Thick. (10mm coarse thread). (Also see our 646-153 newer style under Husqvarna). 651-174 537 04 41-02 Chain Adjuster For chain saw models: 2163, 2165, 2171, CS2163, CS2165, CS2166, CS2171, CS2172, CS2186 and CS2188. 651-175 537 07 12-01 Chain Adjuster Assembly Found on model: 2159 chain saw. (Includes part#’s 503869101 and 503885401) 570-283 537 15 73-02 Cylinder Assy (47mm) Will also fit Jonsereds models: 2156 & 2159. (47mm X 1.5mm). Displacement: 59cc; Stroke: 34mm. NOTE: If your cylinder is equipped with nipple on the cylinder base, decompression side. This was used to operate the automatic decompression valve. You will need to replace this old automatic with a manually decompression valve. (Order# 570-003). Includes: cylinder, piston and ring, piston pin and clips. Gasket and Decompression Valve NOT included. 570-286 503 69 10-73 503 93 90-03 503 93 90-05 503 53 90-71 503 93 90-71 503 93 90-72 Cylinder Assy (48mm) Fits chain saw models: 2065 and 2165. Note: Decompression valve NOT included - Comes with threaded plug only. 2156 / 2159 2065 & 2165 ICS JONSEREDS continued 16-30
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
605-710 71752Air FilterFits ICS Concrete / Cut off Saw models:603GC, 613GC, 633GC and 680GC. Size: 3-7/8” OD X 2-3/8” ID X 3-1/4” HT. Same as our 605-709 except higher.
605-711 73336Pre FilterFor use with our 605-710 air filter. Fits ICS Concrete / Cut off Saw Size: 2-3/8” bottom OD X 2-1/16” top OD X 2-9/16” HT.
592-106 505375Crankshaft Bearing Fits ICS concrete saws, Size: 15mm (37/64”) ID X 35mm (1-3/8”) OD X 11mm (7/16”) HT. Bearing# 6202 - open both sides)
593-103 73209Crankshaft bearing Fits ICS models: 613GC, 633GC and 680GC; Size: 17mm ID X 40mm OD X 12mm HT.(Bearing# 6203/C3) Open both sides.
JONSEREDS605-173 501 80 71-01
501 80 71-05
Air Filter For Chain Saw model: 630
605-062 503 81 45-03Air Filter For chain saw models: 2063, 2071, 2163 and 2171. Nylon mesh style.Size: 3-5/8” L x 2-7/8” W x 1-5/8” HT.
605-060 537 02 40-03
Air Filter (Twist on) For chain saw models:2141, 2145, 2149, 2150 and 2152. Air filter attaches by simply twisting on the carburetor manifold. Note: Some 346 and 353 models use a steel snap to connect.
657-120 503 86 92-01
Anti Vibration Damping Fits chain saw models: 2147 and 2152.Measures: 11/16” L X 9/16” OD with a 3/16” ID.
646-154 503 74 44-01Clutch Assembly For chain saw models: 2063, 2065, 2163, 2165, 2071 & 2171. Measures: 3.057” OD X 0.471” Thick.
Chain Adjuster Assembly Found on model: 2159 chain saw.(Includes part#’s 503869101 and 503885401)
570-283 537 15 73-02
Cylinder Assy (47mm) Will also fit Jonsereds models: 2156 & 2159. (47mm X 1.5mm).
Displacement: 59cc; Stroke: 34mm. NOTE: If your cylinder is equipped with nipple on the cylinder base, decompression side. This was used to operate the automatic decompression valve. You will need to replace this old automatic with a manually decompression valve. (Order# 570-003). Includes: cylinder, piston and ring, piston pin and clips. Gasket and Decompression Valve NOT included.
Note: Older model chainsaws have a crankshaft connecting rod with smaller (13mm bore). This piston fits a 15mm connecting rod. Replaces 503 92 04-71 before SN 020700001.
572-705 537 15 72-02
Piston Assembly (47mm) Fits chain saw model: 2059 and 2159.
2071 & 2171
2095
(While Quantiities Last)
572-499 503 53 90-02
Piston Assembly (48mm) For chain saw models:625 and 630. Direct replacement for the original (48mm) bore Jonsereds cylinder assembly.
574-206 503 28 90-02Piston Ring Set (40mm X 1.5mm)Fits chain saw model: 2040.
574-212 503 28 90-05Piston Ring Set (42mm X 1.5mm)Fits chain saw model: 2045.
574-230 503 28 90-29Piston Ring Set (47mm X 1.5mm) Fits chain saw model: 2063 & 2163.
574-232 501 20 56-02 503 28 90-15
Piston Ring Set (48mm X 1.5mm).Fits Jonsereds chain saw model: 630.Note: Some applications use one only piston ring.
574-157 501 20 56-02503 28 90-15
Piston Ring only (48mm X 1.5mm) Fits chain saw model: 630.For our 572-499 piston assembly.
574-264 1128-034-3000
Piston Ring Set (50mm X 1.2mm)Fits chain saw models: 371 EPA and 372 EPA.(Priced and Sold in sets)
574-137 503 28 90-17
Piston Ring only (50mm X 1.5mm)Fits chain saw model: 670.For our 572-524 piston assembly.
574-266 1122-034-3001
Piston Ring Set (54mm X 1.2mm)Fits some chain saw model: 385.(Priced and Sold in sets)
574-254 503 28 90-22
Piston Ring Set (54mm X 1.5mm) Fits chain saw model: 2083.
570-003 503 71 53-01
Decompression Valve For Chain Saw and Concrete saw cylinder assemblies. Overall Length: 1-7/16” - Blue knob with 2 holes in nut.
570-005 503 665 601
Decompression Valve For Chain Saw and Concrete saw cylinder assemblies. Fits Husqvarna, Jonsereds and Partner models: K1250 etc. Overall Length: 1-7/8” - Blue knob with 2 holes in nut. Similar to our 570-003 but with a longer main body.
623-820 501 51 22-02
Head / Base GasketFits models: 630 and 670.
623-822 503 96 15-01
Head / Base Gasket onlyFits chain saw models: 362, 365, 372, 372 and 375; also fits Jonsereds models: 2065, 2071, 2162 and 2171.
Electronic Ignition Fits chain saw models:625, 630 and 670.The electronic ignitioncomponent is connectedwith the ignition coil toachieve full ignition.This type of ignition module utilizes transistor switches for magnet activation.
Starter Spring For chain saw models: 450, 455, 510SP, 520SP, 525 and 535.
625-325 507 10 00-73
Starter Spring For chain saw models: M36, 361, 361E, 365, 370 and 380.
625-426 505 29 51-26
Starter Spring For chain saw models: 490 and 590.
625-404 501 76 31-01
Starter SpringFor chain saw model: 2041.
Note: Will work on Husqvarna chain saw models: 340, 345, 346, 350, 351, 357, 359 if you re-use the original starter spring case - You will have to make a slight adjustment to the outside spring hook. (This spring is NOT an exact replacement for the Original Husqvarna# 537 09 31 01)
625-430 503 43 19-01
Starter Spring For chain saw models: 2077,2083 Turbo and 2095.Spring is in a plastic cage,Spring OD = 73mm (While Quantities Last)
(Sold in multiples of 10)
625-408 537 10 93-101Starter Spring For chain saw models: 2149, 2159, CS2141, CS2145, CS2150, CS2152, CS2153, CS2156 and CS2159.Spring is in a plastic cage,Spring OD = 67mm / 2-5/8” approximately.
636-145 503 76 53-01
Muffler / Exhaust For chain saw models: 2063, 2065,2071, 2163, 2165 and 2171. Exhaust mounting holes are 53mmcenter to center. This muffler is a NON DF version NOT US Forest Service approved. (Also see our 636-143)
636-143 503 76 53-02503 76 54-02
Muffler / Exhaust For chain saw models: 2063, 2065, 2071, 2163, 2165 and 2171. Exhaust mounting holes are 53mm center to center. Comes with spark arrester. (Also see our 636-145)
636-148 503 71 13-07
Muffler / ExhaustFits chain saw models: 2094 & 2095. Mounting bolts holes are on 52mmcentres. NOTE 1: This muffleris a NON DF version NOT US Forest Service approved. (Also see our 636-149) Front and back images shown for reference
636-149 503 71 13-04
Muffler / ExhaustFor chain saw models: 2094 & 2095. Mounting boltsholes are on 52mm centres. Note: Complete with spark arrester screen. (Also see our 636-148). Front and back images shown for reference.
705-574T-WrenchFits chain saw models: 510, 525, 530, 535, 630,670 and most other Jonsereds models.Size: A= 7”, B= 1”, C= 1”. Bar= 1/2” (13mm),Plug= 3/4” (19mm)
16-33
JONSEREDS continued JONSEREDS continued
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
Starter Spring For chain saw models: Mac 1-10, 2-10, 3-10, 4-10, 5-10E, 6-10, CP 55, 70, 10-1C and 52-10A.
625-202 83078Starter SpringFor chain saw models: Mac 110, 115, 120, 130, 140, Mini Mac 6, 25, 30, 35, Power Mac 6, Pro Mac 55, 510, Super Pro 40, 310, 320, 330, 340 & Titan 7.
625-203 83334 / 87680Starter Spring For chain saw models: Pro Mac 10-10, 55, 60, 555, 570, 610, 650, 700, 800, 805, 850, 1010S, 5700, 8200,Super Pro 60, 70, 80, 81 and Model 7-10A.
OLEO MAC 625-675 50 00132Starter Spring For chain saw models: 250, 251, 251E, 251 Super, 252, 254 and early model 264.Note: Comes in a plastic case not shown
Air FilterFits Concrete / Cut-off Saws models: K650 Active and K700 Active. Size: 4-3/4” L X 3-3/8” W X 2-1/8” HT.Note: Top and Bottom images shown for reference.(For Pre Filter see our 605-239).
16-35
McCULLOCH continued McCULLOCH continued
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
605-239 506 22 63-01 / 999810Pre filterFits chain saw models: K650 Active and K700.(3) layer foam filterSize: 7-7/8” L X 4-1/2” W X 3/4” HT
605-378 544 18 16-01
Air FilterPanel Air filter for Concrete / Cut Quik Saw model: K750. (For use with our 605-377 pre filter)Base Size: 4-15/16” L X 4-1/2” W X 1-3/8” HT.
605-377 506 36 71-01Pre filter For Concrete / Cut Quik Saw model: K750. (For use with our 605-378 air filter) Size: 7-5/64” L X 5-1/2” W X 13/16” HT.
605-440 506 23 19-01506 25 59-32
Pre Filter(3) Layer foam filter. Fits chain saw models:K950 Active & K960 Cut Quik saws. Size: 10-3/8” L X 5-1/4” W X 3/4” HT approx.(Also see our 605-438 Air Filter)
605-438 506 23 18-01506 23 18-02
Air FilterFits chain saw models: K950 and K1250 Active Cut Quik saws. Size: 6” L X 4-1/8” W X 2-5/8” HT
605-414 506 34 70-02
Air FilterFits Husqvarna and PartnerConcrete Saw / Cut Quik sawmodles: K950 and K960.Size: 6” L X 4-1/8” W X 2-1/2” HT
605-280 506 26 87-01
Pre filterFits Concrete / Cut Quick Saw models: K1250. (3) layer foam filter.Size: 10-5/32” L X 6-1/2” W X 13/16” HT.
605-400 510 24 41-01510 24 41-03
Air FilterFits Husqvarna and PartnerConcrete Saw / Cut Quik sawmodels: K970 and K1260.Size: 5-3/4” L X 4-1/4” W X 3-3/8” HT.
875-724 506 07 05-03Drive belt (cogged)For concrete / cut quick saw model: K950 with 12” and 14” blades. Size: 3/8” W X 34-1/2” L
875-712 506 29 67-02 544 90 84-02
Drive belt (multi rib)For concrete / cut quick saw model: K750. Size: .551” W X 32” L (6 rib, polyester cord construction)
875-725 506 07 05-04 506 34 74-24
Drive belt (cogged)For concrete / cut quick saw model: K950 Active with 16” blades. Size: 3/8” W X 36” L
875-711 506 03 30-31 506 27 67-41
Drive belt (cogged)For concrete / cut quick saw model: K650 Active, K650 Active II and K700 Active II Size: 1/4” W X 31-1/2” L
875-713 506 07 05-06Drive belt (cogged)For concrete / cut quick saw model: K650 Active III andK700 Active III cut off saws. Size: 3/8” W X 31-1/2” L
875-726 506 07 05-07Drive belt (cogged)For concrete / cut quick saw model: K1250 Active cut off saws. Size: 3/8” W X 39-1/2” L
670-101 503 22 00-01Bar NutFits chain saw models: R16, S50, S55, P55, P70 and P100. Size: 8mm X 1.25 thread. For 13mm T-wrench
Decompression Valve For Chain Saw and Concrete saw cylinder assemblies. Fits models: K650 and K700, Active I, II, III. Overall Length: 2” - Black knob with 1 holes in nut. Similar to our 570-004 but with different knob. (For plug only see our 570-001)
K1250
(While Quantities Last)
16-37
PARTNER continued PARTNER continued
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
570-005 503 66 56-01Decompression Valve (Blue Knob) For Chain Saw and Concrete saw cylinder assemblies. Fits Husqvarna, Jonsereds and Partner models: K1250 etc. Overall Length: 1-7/8” - Blue knob with 2 holes in nut. Similar to our 570-003 but with a longer main body.
625-325 504 35 27-05Starter Spring For chain saw models: MINI P, P2, 3, 4, 330, 340, 350, P11 and P12.
625-429 506 25 89-01
Starter Spring For Partner / Husqvarna Concrete Saw / Cut Quik Saw models: K750, K760, K960 and K970.(Replacement starter spring for our 655-250 starter assembly).
655-250 506 38 56-12
Starter Assembly For concrete / cut quik saw model: K750. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, handle etc. Just needs to be bolted on
16-38
PARTNER continued PARTNER continued
Small Engine Parts & Accessories CHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
605-040 530 05 79-25
Air Filter - Felt.Fits chain saw models: P3314,P3314WS, P3314WSA, P3416,P3516PR, P4018, P4018WM,P4018WT, P4018WTL, PP3516, PP3816, PP4018, PP4218, PPB3416, PPB4018, PPB4218, S1970 and Type1 Size: 3-7/16” L X 2-5/8” W X 3/16” Thick.
605-087 530 057869
Air FilterFits chain saw models: P3818AV, P4018AV, PP3516AVX,PP4218AV, PP4218AVHD, PP4218AVL,PP4218AVX, SM4218AV, SM4218AVX.Size: 3” L X 3-1/4” W X 3/16” HT.
605-428 23791530 023791
Air FilterFits chain saw models: Micro XXV, Micro 25, 180, 200, 205, 225, 235, 236, 1800, 2000, 2100, 2300, 2350 and 2400. Size: 2-5/8” L X 1-1/2” W X 1” HT
605-436 23369530 023369
Air FilterFits chain saw models: 25 and 25DASize: 3-3/8” L X 1-5/8” W X 1-1/4” HT
605-410 2586530 002586
Air FilterFits chain saw model: 361 Size: 4-1/8” L X 3-1/2” W
605-515 530 037793
Air Filter Fits chain saw models: 1950, 2050, 2075, 210, 2150, 2175, 2250, 230, 2450, 2550, 260, Pro 221, 221LE, 2375, Wild Thing, 1900, 2350, 2055, 220, 225 and Woodsman. Size: 3-1/4” L X 2-1/2” W X 3/4” HT
605-091 575 29 63-01
Air FilterFits chain saw models: PP5020AV.Size: 2-7/8” L X 3” W X 7/8” HT.
605-486 036141530 036141545 057701
Air FilterFits chain saw models: 2200, 2500, 2600, 2700, 2750, 2775, 2900, 3050, PP4620AVHD, PP4620AVL and Poulan Pro 255, 295, 310 and 315.Size: 3” L X 2-3/4” W X 7/8” HT
605-402 24548 / 20913530 024548952 014129
Air FilterFits chain saw models: 3400 and 3700. Size: 3-7/8” L X 2-5/8” W X 1” HT
646-129 93919ClutchFor many small Poulan chain saw and Poulan / Weedeater Trimmer models. Measures: 2-3/8” OD, steel washer included.
621-132Clutch SpringFor chain saw models:201, 221, 361, 401 and 451.
Fuel Filter Replacement felt filter for our 610-014 in-tank fuel filter. Fuel Filter for many Poulan chain saw models. Measures: 1” Long X 1/4” ID X 9/16” OD.
610-030 34032530 034032
Fuel FilterReplacement felt filter for our 610-006 in-tank fuel filter. Fuel Filter for many Poulan chain saw models. Measures: 1” Long X 7/16” ID X 13/16” OD.
(While Quantities Last)
(Sold in multiples of 10)
(Sold in multiples of 10)
16-39
POULAN continued POULAN continued
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
610-345 530 023166 530 026119
Duck Bill Valve For Homelite chain saw models XL, XL-2 and Super 2. Duck Bill Valve - Fits Homelite Trimmers and Chain Saws. Measures: .100” ID X .201” OD X .25” L
Starter PulleyFits chain saw models: 2200, 2500, 255, 2600, 2750, 2900, 295, 3050, 310, 315. Starter Pulley for Poulan saws -Dealers have used it on Husqvarna model 41 Chain Saw. May fit other Husky saws? (4) cog pulley. NOTE: original Husky application is (6) cog.
145-516Starter Rope AssemblyFor chain saw models: 25D and also 180 and 190. Rope length 21”, plastic knob fastened to rope end.
Starter Spring For chain saw models: 3400 and 3700. Starter Spring for Sears / Roper / AYP chain saw models: 358-354810, 358-354830 (3.4, 3.7 CU. IN. Poulan)
625-101 4262
Starter SpringFor Lombard chain saw models: 42 series, Lightning and Comango. Starter Spring for Poulan chain saw models: 360, 361 and 400.
REMINGTON605-523 66241Air FilterFits chain saw model: Mighty Mite (Large version). Made of felt material. Size: 3-9/16” L X 3-1/4” to 4-1/16” W (bottom)
605-553 65071Air FilterFits chain saw model: SL9 and SL9 deluxe. Made of felt material. Size: 3-5/8” L X 3-5/8” W.
560-101 60832Starter Dog / Starter Pawl. Found on many older Remington chain saws using an aluminum starter cup. Remington models:PL-4, SL-4A, Bantam etc.Size: Dog width: 1/2” with a 3/8” ID.
(While Quantities Last)
16-40
POULAN continued POULAN continued
Small Engine Parts & Accessories CHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
541-103 1108-140-1000Air filter capFits chain saw models: 08 and 08S. (For use with our 605-708 air filter)
605-719 1120-120-16001120-124-0800
Air filter Fits chain saw model: 009, 010, 011. Size: 3-7/8” L X 2-5/8” W
605-717 1130-124-0800Plate filter Fits chain saw models: 017, 018, MS170 and MS180. Size: 3-1/2” L X 2-9/16” W approximately.
605-724 1132-124-0800
Air FilterFits chain saw models:019T, MS 190T and MS 191T.Size: 3” L X 3” W X 1/16” HT.
605-721 1139-124-0800
Air FilterFits chain saw model: MS171.Size: 4-1/8” L X 2-3/4” W X 1/4” HT.
605-723 1139-120-1602
Air FilterFits chain saw models:MS 171, MS 181 and MS 211.Size: 4” L X ____” W X 3/4” HT.
605-718 1137-120-1600
Air FilterFits chain saw model: MS192 T.Size: 4” L X 2-1/2” W X 5/8” HT.
Air FilterFits chain saw model: MS 020 T and MS200 T.Size: 3-1/2” L X 2-3/4” W X 5/8” HT.
605-722 1145-140-4400
Air FilterFits chain saw model: MS 201 T.
Size: 4-7/16” L X 3” W X 3/4” HT.
560-102 Starter Dog WasherThis is a fibre washer used on olderFairbanks Morse, Remington chain saws thatused a starter dog assembly and aluminum starter cup.
SEARS / ROPER / AYP605-907 9163HAir FilterFits AYP / Sears/ Roper Chain Saw. Sears model 3.7 cubic inch Size: 3-7/8” L X 3-5/8” W
Starter SpringFor chain saw models:415 and 450 (older models)
STIHL605-708 1108-120-1600
Air FilterFits chain saw models: 08 and 08S
(Sold in multiples of 10)
16-41
REMINGTON continued STIHL continued
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
605-687 1123-120-16131123-120-1612
Air FilterFits Chain Saw models: MS210, MS230 and MS250.
Size: 3-5/8” L X 1-3/16” W X 1-3/8” HT.
605-727 1141-120-1600
Air FilterFits chain saw models:MS231, MS251, MS271,MS291, MS311, MS362C and MS391.Size: 3.08” OD X1.675” Bottom opening ID X 1.7” Height.
605-741 1121-120-1617
Air Filter Fits chain saw models:024, 026 (new style),MS240 and MS260with a standard styletank vent.
“For chainsaw models that DO have the carburetor compensator”.Size: 3-1/8” L X 3-1/2” W X 1-1/4” HT approximately. (Top and Bottom pictures shown (1) air filter only)
605-740 1121-120-1612
Air FilterFits chain saw model: 026 PRO.
“For chainsaw models that DO NOThave the carburetor compensator”.
Size: 3-1/8” L X 3” W X 1-1/4” HT approximately.
605-745 1140-140-4401
Fits chain saw models: MS 311, MS 362 & MS 391.
Size: 4-3/8" L X 3-5/8" W X 1-7/8" HT.(Top and bottom images shown for reference.)
605-732 1133-120-1604
Air FilterFits chain saw model: MS270 and MS280.Size: 4” L X 4” W X 1-11/16” HT.
605-679 1127-120-16211127-120-1620
Air Filter Fits chain sawmodels: 029, MS290,MS310 and MS390.
Size: 4-9/16” L X 2-5/8” W X 1-1/2” HT. (Top and Bottom pictures shown (1) air filter only)
605-742 1135-120-1600
Air FilterFits chain saw model: MS341 and MS361.
Size: 4-5/8” L X 2-13/16” W X 1-11/16” HT.
605-733 1118-120-16101118-120-16111118-120-1615
Air Filter Fits chain saw models:028, 028 Super and 028 Wood Boss.Size: 3-1/2” L X 2-1/4” W X 3/4” HT
605-753 1125-120-16151125-120-1620
Fits chain saw models: 034, 034 Super and 036.
NOTE: Fits older 034 chainsawsbefore serial number 1 45 945 205. Fits older 036 chainsaws before serial number X 32 622 639. This fi lter doesn’t have the compensator hole, and is too narrow for newer models 034 & 036. Please verify serial number fi rst before purchasing.Size: 3-1/4” L X 2-7/8” W X 1-1/8” HT
605-736 1125-120-1626
Fits chain saws models:034 and 036.
NOTE: Fits newer 034 chainsawsafter serial number 1 45 945 205.Fits older 036 chainsaws after serial number X 32 622 639;also found on models: MS340 and MS360.This fi lter has the compensator hole, and is too wide for older models 034 & 036. Please verify serial number fi rst before purchasing.Size: 4-1/8” L X 3-5/8” W X 1-5/8” HT.
606-138 1119-140-1903 1119-140-1905
Air filter cover
Aftermarket box cover for chainsaw model 038 series.
This plastic piece often takes most of abuse from day to day use and fadesin colour. Includes attachment nut and mesh screen.
605-073 1119-120-1630
Air FilterFits chain saw model: MS381.
Size:4-1/8” L X 3-1/16” W X 15/16” HT.
16-42
STIHL continued STIHL continued
Small Engine Parts & Accessories CHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
STIHL continued STIHL continued
16-43
605-691 4201-141-0310
Air Filter Wrap Fits Concrete / Cut off Saw models: TS350, TS360 and TS510 / TS760. Felt wrap with stitched elastic for tight seal. (Pre filter for our 605-709)
605-055 4201-140-1802
Inner Air Filter Fits Concrete / Cut off Saw model: TS360. Inner filter - centre bolt mount style.(Inner filter for our 605-709)
605-336 4223-141-0300
Air FilterFits Concrete / Cut off Saw model: TS400 (air filter). Size: 5-3/8” L X 3-3/8” W X 1-15/16” HT. (Paper element with soft foam seal)
605-332 4223-140-03004223-140-1800
Air FilterFits Concrete / Cut off Saw model: TS400 (secondary filter). Size: 4-5/8” L X 2-11/16” W X Pipe: 1-1/8” OD X 7/8” HT
605-337 4223-141-0600Air Filter Fits Concrete / Cut off Sawmodel: TS400 (pre filter). Size: 5” L X 3-1/8” W X 13/16” HT, Centre hole 5/16”, Offset hole 3/16” ID. (3) layer foam
605-348 4221-140-44004221-141-0300
Air Filter Fits Stihl Concrete / Cut off Saw models: TS460 / TS510 / TS760 (air filter). Size: 4-1/2” OD X 2-1/16” ID X 2-1/4” HT. (Use with our 605-343 & 605-346)
605-343 4221-140-1800Air Filter Fits Stihl Concrete / Cut off Saw models: TS460 / TS510 / TS760 (inner filter). Size: 1-7/8” OD X 1-11/16” ID X 1-11/16” HT. (Use with our 605-348 and 605-346)
605-346 4221-141-0310
Air FilterFits Stihl Concrete / Cut off Saw models: TS460 / TS510 / TS760 (pre filter). Made of felt material.(Use with our 605-348 and 605-343)
605-675 1110-120-1601
Air FilterFits chain saw model: 041. Made of wire mesh & felt material. Size: 4-1/4” L X 4-1/8” W
541-106 1110-140-9500
Air filter cap Fits chain saw models: 041, 051 and 070. (For use with our 605-675 / 605-676 / 605-686 air filters)
605-676 1111-120-1601Air FilterFits chain saw models: 051 and 076. Made of wire mesh & felt material. Size: 5” L X 4-1/4” W
605-683 1113-120-16021113-120-16031113-120-1612
Air Filter Fits chain saw models: 031 and 032. Size: 3-1/8” L X 2-5/8” W X 15/16” HT
605-735 0000-120-1653 / 0000-120-1654
Air FilterFits chain saw models: 044, 046, 064, 066, 088, MS440, MS441, MS460, MS640, MS650, MS660 and MS880. Felt cloth outer wrap with a foam filled interior. Designed for oil-less use. (Top and bottom images shown for reference.)Size: 4-3/16” L X 3-1/8” W X 1-3/4” HT
605-725 4201-140-1801
Air FilterFits Concrete / Cut off Saw models: TS350 and old style TS510 / TS760Inner filter - 2 bolt mount style(Inner filter for our 605-709)
605-709 4201-140-18054201-141-0300
Air Filter Fits Concrete / Cut off Saw models: TS350, TS350AVE, TS360, TS510 and TS760. Size: 3-7/8” OD X 2-3/8” ID X 2-7/8” HT (Also found on Sachs Cut off saws)
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
605-692 4224-141-03004224-141-0300A
Air Filter Fits Concrete / Cut off Saw models: TS700 and TS800. Size: 5-1/2” L X 4-1/16” W X 1-3/4” HT. (Paper element with soft foam seal). Uses our 605-700 pre filter.
605-700 4224-140-1801Air Filter Pre Filter (secondary filter)Fits Concrete / Cut off Saw models: TS700 and TS800. Size: 4-5/8” L X 3-1/4” W X 9/32” HT. For use with our 605-692 air filter.
Filter Kit for TS350 & TS510605-800 4201-140-1801
4201-140-18054201-141-0300 4201-141-0310
Air Filter (3) Piece Kit Fits Concrete / Cut off Saw models: TS350 and TS510
Air Filter Kit for STIHL TS360605-810 4201-140-1801
4201-140-18024201-141-0310
Air Filter (3) Piece Kit Fits Stihl Concrete /Cut off Saw model: TS360
Air Filter Kit for TS400605-820 4223-007-1010 / 4223-140-1800
4223-141-0300 / 4223-141-0600
Air Filter (3) Piece Kit Fits Stihl Concrete / Cut off Saw model: TS400. Kit includes: (1) 605-336, (1) 605-332 and (1) 605-337
Filter Kit for TS460, TS760605-840 4221-007-1002
4221-140-18004221-140-44004221-141-0310
Air Filter (3) Piece Kit Fits Concrete / Cut off Saw models: TS460 / TS760
Filter kit for TS410 and TS420605-850 4238-140-1800
Air Filter (2) Piece Kit Fits Concrete / Cut off Saw models: TS410 / TS420. (Includes (1) 605-559 pre filter andpanel filter). The panel filter measures:5-3/4” L X 5-1/2” W X 1-3/4” HT approximately.
657-134 1118-790-9930Anti Vibration Damping Anti Vibration Damping For chain saw models: 028 and 038. Size: Steel plate: 1-11/16” Long X 1-3/16” Wide, with (2) 3/16” holes
657-136 1121-790-99061121-790-9909
Anti Vibration Damping For chain saw models: 024, 026, 028 and 038.Size: 15/16” OD (steel washer end) X 1-5/16” OD (rubber end) with a taper to 11/16” ID in rubber end. Overall height: 1-1/16”
657-135 1121-790-99111121-790-9912
Anti Vibration Damping Anti Vibration Damping for chain sawmodels: 024, 026, 038 & 088. Size: 1” OD (steel washer end) X 1-1/8” OD (rubber end) with a 3/8” ID in rubber end. Overall height: 1-1/16”
657-009 1111-790-9905
Anti Vibration Damping For chain saw models: 015AV, 051, 076 and TS510. Use on front handle, upper damper. Size: 1-1/4” OD with a 5/16” ID hole in the steel end.
657-010 1111-790-9915Anti Vibration Damping For chain saw models: 015AV, 051, 076 and TS510. Use on front handle, lower damper. Size: 1-11/16” OD with 25/32” ID hole in the steel end.
657-140 1111-790-9900Anti Vibration Damping Fits chain saw models: 051, 076 and TS510. Use on back handle. Size: 1-3/8” OD with 5/16” ID hole in the steel end.
657-532 1120-790-9600
Anti Vibration Damping For chain saw models: 010, 011, 012 AV and 019T. (While Quantities Last)
16-44
STIHL continued STIHL continued
Small Engine Parts & Accessories CHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
657-081 1123-791-2800Anti Vibration Damping For chain saw models: MS170, MS180, MS270 and MS280. Size: 22mm (top recessed) / 25mm (bottom) X 11mm ID (recessed at the top) X 30mm overall length
657-082 1123-790-9900Anti Vibration Damping For chain saw models: 021, 023, 025, MS210, MS230 and MS250. Size: 22mm (top) / 25mm (bottom) X 11mm ID X 30mm overall length
657-083 1123-791-2805Anti Vibration Damping For chain saw models: 021, 023, 025, 029, 039, MS210, MS230, MS250, MS290 and MS390. Size: 23mm OD X 8mm ID X 30mm overall length
657-144 1122-790-9905Anti Vibration Damping For chain saw models: 028, 044, 046, 064, 066,MS440, MS460, MS461,MS640, MS660 chainsaws.Size: 1.00” / 25mm Bottom ODX .866” / 22mm Top OD (steel washer end) with 6mm ID hole. Overall HT: 1.10” / 28mm. (Two images shown for reference)
657-087 1125-791-2805Anti Vibration Damping For chain saw models: 034, 036, MS340 and MS360Size: 1-1/4” OD X 1” HT.
657-084 1128-790-9900
Anti Vibration Damping Tank / Annular Bufferfor chain saw models:044, 046, MS440, and 460.(Two pictures shown for reference)
657-088 1122-790-9920Anti Vibration DampingFor chain saw models:066 and MS 660.Size: 1.70” L X 1-180” W X 1.03” HT.
657-145 4205-790-9301 Anti Vibration Damping For concrete saw / cutquik saw models:TS510 and TS760.Size: 1.18” OD X 1.18” HT.
657-146 4205-790-9300Anti Vibration Damping For for concrete saw / cutquik saw models:TS410, TS420, TS480i, TS500i, TS510,TS700, TS760 and TS800.Size: 30mm OD X 15mm HT.
670-114 0000-955-0801Bar Nuts Bar nuts for Chain Saw models:021, 023, 025, 026, 028 series,038 Super series, 044, 064 etc. Size: 8mm X 1.25 thread
653-122 Bar Plate Set For chain saw model:08S (newer style)
653-113 1111-664-10001111-664-1005
Bar Plate Set For chain saw models: 050, 051 and 075.
670-201 0000-953-6605Bar studFits chain saw models: 024, 026, 028,034, 036, 038, 042, 044, 046, 048, 064, 066,MS 240, MS 260, MS 340, MS 341, MS 360, MS 361,MS 380, MS 440, MS 460, MS 640, MS 650, and MS 660.Size: 8mm with a 12mm wide collar X 42mm overall length.(Uses our 670-114 bar nuts)
875-272 9490-000-78409490-000-7850
Drive belt (cogged)For Cut Quik models: TS350, TS360 and TS460. Size: 3/8” W X 33-3/4” L
(Priced and Sold Individually)
(Sold in multiples of 10)
(Sold in multiples of 10)
16-45
STIHL continued STIHL continued
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
875-273 9490-000-7851Drive belt (cogged)For concrete / cut off saw model:TS400. Size: 3/8” W X 34-7/16” L
875-3820 9490-000-7901Drive belt (Type 6) MULTI RIBBEDFor concrete / cut off saw models: TS410 and TS480i. Size: 1/2” W X 29-1/2” L.
875-3821 9490-000-7900Drive belt (Type 6) MULTI RIBBEDFor concrete / cut off saw models: TS420 and TS500i. Size: 7/16” W X 32” L.
875-3822 9490-000-78919490-000-7892
Drive belt (cogged)For concrete / cut off saw models: TS510 and TS760 with 14” blade Size: 3/8” W X 36.3” L.
Original Tillotson carburetor HS-320 / HS-320A.Found on Stihl chain saw models: 066 and MS660.Will replaces Zama C3A-S31 and Walbro WJ-67. Two images shown for reference.
FOR OTHER CARBURETOR PARTSSEE SECTIONS 10 and 11
606-776 9771-021-2580Clamping Collar Fits many Rubber Intake Elbowsfound on Stihl chain saws.
606-408 1123-141-2200
Carburetor Rubber Elbow Intake Manifold - Rubber. Fit Stihl chain saw models: 021, 023, 025, MS210 and MS250.
Clutch Assembly For chain saw models: 026 and MS260. (Washer plate includedas shown in picture).Measures: 2.675” OD X 0.403” Thick. 19mm nut attached to this clutch for removal.
646-114 1127-160-2051
Clutch Assembly For chain saw models: 029 and 039. (Washer plate includedas shown in picture). Measures: 2.928” OD X 0.403” Thick. 19mm nut attached to this clutch for removal.
646-116 1108-160-2002Clutch AssemblyFor chain saw model: 08S and Cut Quik models: TS350 and TS360.
Measures: 2-19/32” OD X 1/2” ID X 3/16” keyway
646-120 1119-160-2000Clutch Assembly For chain sawmodel: 038 series. Measures: 2-3/4” OD X 9/16” IDX 5/8” Overall Height.
646-117 1125-165-2052
Clutch Assembly For chain saw models: 036 / MS360.
Measures: 2.894” OD X 0.390” Thick. 19mm nut attached to this clutch for removal.
646-123 1125-160-20051125-160-2006
Clutch Assembly For concrete / cut quik saw model: TS400.
Measures: 2.885” OD
646-119 1122-160-20021122-160-2005
Clutch AssemblyFor chain saw models: 064, 066, MS640 and MS660.(Washer plate includedas shown in picture).
Measures: 3.140” OD X 0.460” Thick. 19mm nut attached to this clutch for removal.
646-124 1128-160-20001128-160-20041128-160-2001
Clutch AssemblyFor chain saw models: 044, 046, MS440, MS460, also fits MS341 & MS361. (Washer plate included as shown in picture). Measures: 2.916” OD X 0.392” Thick. 19mm nut attached to this clutch for removal.
16-47
STIHL continued STIHL continued
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
Cylinder Assy (38mm)Fits chain saw models:018 and MS180.Bore: 37 mm, Stroke: 28 mm, Displacement: 31.8 cc, Rings: 38 mm X 1.2 mm.
Important Note: Older 018 chainsaws made before serialnumber 2 44 534 710 have an 8mm wrist pin. This assembly will not fit.
570-188 1129-020-12021129-020-1206
Cylinder Assy (40mm)Fits chain saw models:020 T, MS 200 and MS200T.Bore: 40 mm, Stroke: 28 mm, Displacement: 35.2 cc, Rings: 40 mm X 1.5 mm.
570-189 1123-020-12091123-020-12231125-020-1224
Cylinder Assy (42.5mm)Fits chain saw models:0025 and MS250.Bore: 42.5 mm, Stroke: 32 mm, Displacement: 45 cc, Rings: 42.5 mm X 1.2 mm.NOTE: Will also fit on the smaller cousin model: 023 and MS230.
570-281 1121-020-12031121-020-1209
Cylinder Assy (44mm)Fits chain saw models: 026, MS260;NOTE: Will also fit024AV and 024 Super(Stihl# 1121-020-1200).
Clutch Spring Fits chain saw models:064, 066, MS640 and MS660. Size: 7/8” overall length
570-186 1130-020-1207Cylinder Assy (37mm)Fits chain saw models: 017 (NOTE)and MS170NOTE: This cylinder assembly fits model017’s after the sn 2 44 076 105 whichhave the later style ignition coil. If you havethe earlier style ignition coil, you will have tochange your coil and your flywheel.Bore: 37 mm, Stroke: 28 mm, Displacement: 30.1 cc, Rings: 37 mm X 1.2 mm.
570-183 1137-020-12011137-020-1204
Cylinder Assy (37mm)Fits chain saw models:MS192T.Bore: 37 mm,
(Sold in multiples of 3)
(Sold in multiples of 3)
(Sold in multiples of 3)
(Sold in multiples of 3)
(Sold in multiples of 3)
017 & MS170
MS192T
16-48
STIHL continued STIHL continued
Small Engine Parts & Accessories CHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
NOTE 1: This cylinderassembly has a holefor a decompression valve.NOTE 2: On older 034 saw (46mm) slight modification is required. Instructions are enclosed.This upgrade will increase your older 034 from 56.5cc to 61.5cc.
570-278 4221-020-1201
Cylinder Assy (48mm) Fits Cut Quik Sawmodel: TS460. Note: This cylinder assemblyhas the threaded hole beside the spark plug for a decompressor. Note: Decompression valve NOT included.
570-196 1127-020-12131127-020-1216
Cylinder Assy (49mm)Fits Stihl chain saw models: 039 and MS390;
NOTE: Will also work onsmaller cousin MS310.
570-227 4201-020-1200
Cylinder Assy (49mm) Fits Cut Quik Saw model: TS-360Replace your TS-350 with this C & P for extra power.
Cylinder Assy (46mm)Fits Stihl chain saw models:029 and MS290.
Bore: 46 mm, Stroke: 34 mm, Displacement: 56.5 cc, Rings: 46 mm X 1.5 mm.
NOTE: Will also fit on the larger cousin model: MS310.This cylinder will also replace the older 029 (45mm bore), beforeSerial Number X 39 305 257) as well.
Cylinder Assy (47mm)Fits chain saw model: MS361. Bore: 47 mm, Stroke: 34 mm, Displacement: 59 cc, Rings: 47 mm X 1.2 mm.
MS261
028, 028 Super
029 & MS290
TS-350 Cut Quik
MS361
16-49
STIHL continued STIHL continued
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
570-161 1128-020-1250
Cylinder Assy (52mm)Fits Stihl Cut Quik / Concrete Saw model: GS 461 ROCK BOSS also used on Stihl chainsaw model: MS461. Includes: cylinder, piston and rings, piston pin & clips.
NOTE: This cylinder is NOT equipped with a De-compression valve hole. For a cylinder with a Decompression valve hole see our 570-206. (Also see our 623-672, 640-238 or 640-272).
570-206 1119-020-1204
Cylinder Assy (52mm)Fits chain saw model: MS381.
Note: Decompression valveNOT included, use our 570-004 Decompression valve.Bore: 52 mm, Stroke: 36 mm,Displacement: 76.5 cc, Rings: 52 mm X 1.5 mm.
NOTE: If your saw is equippedwith a 10mm PISTON PIN you willneed to order our 590-152Crankshaft Assembly separately,which will accept the newer 12mm piston pin.
570-209 1138-020-1201
Cylinder Assy (50mm) Fits chain saw model: MS441 and MS441C.
570-276 4238-020-1202
Cylinder Assy (50mm)Fits Cut Quik Saw models: TS410 and TS420.
Decompression valve NOT included. Comes with threaded plug only.Also see our 640-285 Gasket Set.
TS480i, TS500i
TS400
044 / MS440
MS441 / MS441C
TS410 & TS420
16-50
STIHL continued STIHL continued
Small Engine Parts & Accessories CHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
572-590 4119-030-2003
Piston Assembly (38mm)Fits Trimmer models: FS220 and FS220R.
Piston Assembly (42mm)Fits Stihl chain saw models: MS250. Note: For 025 model with larger 42.5mm bore see our 572-603 piston assembly.(Rings 42 X 1.5mm)
Note: For MS250 model with smaller 42mm bore see our 572-607 piston assembly.(Rings 42.5 X 1.2mm)
572-525 1121-030-2001
Piston Assembly (44mm) Fits chain saw models: 026 and MS260.
NOTE: This piston assembly fits the older 026, MS260 Stihl models before serial# 2 62 187 362. This WILL NOT fit the newer MS260models with the larger 44.67mm bore.
NOTE: This piston assembly fits the newer 026, MS260 Stihl models after serial# 2 62 187 362. NOTE: For the older 44mm piston assembly see our 572-525.
Piston Ring Assembly Tool Kit / Piston Ring Clamp Set.
Useful for assembling pistons and cylinders on chainsaws, trimmer etc. 4 sizes of clamps. Give yourself a third hand with this kit. This kit will compress piston rings ranging from 30mm to 60mm in diameter.
066 & MS660
046 / MS460
TS700 & TS800
TS760
16-51
STIHL continued STIHL continued
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
572-384 1118-030-2001
Piston Assembly (44mm)Fits Chain Saw models: 028 and 028 Wood Boss
“older style”.
572-255 1110-030-20021110-030-2000
Piston Assembly (44mm)Fits Stihl chain saw model: 041 old style.
Piston Assembly (58mm)Fits chain saw models: 075, 076 and TS760.
572-619 1106-030-20001106-030-2003
Piston Assembly (58mm)Fits chain saw model: 070.
574-167 1123-034-3005
Piston Ring Set (40mm X 1.2mm).Fits chain saw model: 023, MS210 (older) and MS230. NOTE: Fits older 021 models (Before S/N X 34 944 403).Note: Some chain saw applications use one only piston ring.
NOTE: YOU WILL NEED TO CONFIRMTHE PISTON RING THICKNESS PRIOR TO ORDERING.
574-212 1121-034-3005Piston Ring Set (42mm X 1.5mm) Fits chain saw models: 024 / MS240. (Priced and sold in sets)
574-214 1110-034-30001121-034-3010
Piston Ring Set (44mm X 1.2mm)Fits chain saw models: 026 and MS260.Fits Stihl trimmer models: FS 480 and FR 480.(Priced and Sold in sets)
574-170 1110-034-30001121-034-3010
Piston Ring - Chrome (44mm X 1.2mm)Fits chain saw models: 026 and MS260. NOTE: YOU WILL NEED TO CONFIRMTHE PISTON RING THICKNESS PRIOR TO ORDERING.(Priced Individually - 2 Required)
574-216 1110-034-3000Piston Ring Set (44mm X 1.5mm) Fits chain saw models:028, 030, 031 and 041.Replacement ring for our 572-525 piston assembly.(Priced and sold in sets)
574-221 1118-034-3001
Piston Ring Set (46mm X 1.5mm)Fits chain saw models: 028 Super, 029,MS290 and 034 (with smaller 46 mm bore).(Replacement rings for our 572-449 piston assembly)
16-53
STIHL continued STIHL continued
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
574-144 1118-034-3001Piston Ring - Chrome (46mm X 1.5mm)Fits chain saw models: 028 Super, 029,MS290 and 034 (with smaller 46mm bore). Replacement ring for our 572-449 piston assembly.(Priced Individually - 2 Required)
574-258 1125-034-3001Piston Ring Set (48mm X 1.2mm)Fits chain saw models:034, 036 and MS360.(Priced and Sold in sets)
574-232 1110-034-3003
Piston Ring Set (48mm X 1.5mm).Fits chain saw model: 041 and will fit many036 and MS360 models using the thicker 1.5mm ring.NOTE: This ring set fits our 572-497 Piston assembly.
Note: Some chain saw applications use one only piston ring.
NOTE: YOU WILL NEED TO CONFIRMTHE PISTON RING THICKNESS PRIOR TO ORDERING.(For thinner 1.2mm piston ring set see our 574-258).
574-234 1127-034-30064201-034-3000
Piston Ring Set (49mm X 1.5mm).Fits chain saw model: 039, MS390Fits Cut Quik models: TS360 and TS400.
For Chrome piston ring see our 574-143.Note: Some chain saw applications use one only piston ring.
NOTE: YOU WILL NEED TO CONFIRMTHE PISTON RING THICKNESS PRIOR TO ORDERING.
574-143 1127-034-3006 4201-034-3000
Piston Ring - Chrome (49mm X 1.5mm)Fits Cut Quik Saw model: TS-360 and TS400.(Priced Individually - 2 Required)
574-264 1128-034-3000
Piston Ring Set (50mm X 1.2mm)Fits chain saw models:044, MS440 and MS441.(Priced and Sold in sets)
574-137 1119-034-3000
Piston Ring - Chrome (50mm X 1.5mm)For chain saw model: 038 Super. (Priced Individually - 2 Required)
574-265 1122-034-3000
Piston Ring Set (52mm X 1.2mm)Fits chain saw models:044 BIG BORE, 046, MS460,064, MS640, MS650 and some 051, TS510 models..(Priced and Sold in sets)
574-248 1115-034-3010
Piston Ring Set (52mm X 1.5mm) Fits chain saw models:038 Magnum, MS380, MS381,045, 048, 050, 051 and 056. (Priced and sold in sets)
574-106 1115-034-30011115-034-3010
Piston Ring - Chrome (52mm X 1.5mm) Fits chain saw model: 038 Magnum,051 and TS510 cut quik saws.(Priced Individually - 2 Required)
574-266 1122-034-3001
Piston Ring Set (54mm X 1.2mm)Fits chain saw models:046 BIG BORE, 066 and MS660.(Priced and Sold in sets)
574-254 1115-034-3012
Piston Ring Set (54mm X 1.5mm) Fits chain saw models: 045 and 056. (Priced and sold in sets)
Note: “Piston Rings” are priced and sold individually. “Piston Ring Sets”
are priced and sold as a set of 2
591-102 9512-003-2250Bearing - Piston Fits chain saw models: 023, 024,025, 026, MS230, MS240, MS250,MS260 and others.(Size: 10mm X 13mm X 12.5mm).
591-101 9512-003-3140Bearing - PistonWrist pin bearing for chain saw models:08S & 038, 038 Super / Magnum and Concrete Saw models TS350 & TS360.(Size: 12mm X 16mm X 13mm)
591-104 9512-003-3061Bearing - Piston Wrist pin bearing for Chain Saw models:044, 046, MS440 and MS460.(Size: 12mm X 15mm X 15mm).
16-54
STIHL continued STIHL continued
Small Engine Parts & Accessories CHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
591-106 9512-003-3281Bearing - Piston Wrist pin bearing for Chain Saw models:066 and MS660. (Size: 12mm X 17mm X 13mm).
591-110 9512-003-3440Bearing - Piston Wrist pin bearing for Chain Saw models:050, 051, 075, 076, 084, 088, MS780,MS880, TS50, TS510 and Cut Quik saw model: TS760.(Size: 13mm X 17mm X 17.5mm)
Crankshaft AssemblyFits chain saw models:064 and 066 (old style).Fits older 064 and 066 models > before serial numberX 33 917 066, MS 640. For newer 066 chainsaws models (approximately 1996 on) that have a larger diameter crankshaft. See part# 590-155.(Uses our 646-119 clutch assembly).
590-155 1122-030-0408
Crankshaft AssemblyFits chain saw model: 064.Fits newer 066 models > before serial numberX 33 917 065, MS 650 and MS660. For older 066 chainsaws models (prior to 1996 approx) that have a smaller diameter crankshaft. See part# 590-154.(Uses our 646-119 clutch assembly).
590-119 1111-030-0402
Crankshaft Assembly For chain saw models: 051, 075and Cut Quik Saw model TS-510.
590-116 1108-030-0402
Crankshaft Assembly For Cut Quik Saw models: TS-350 and TS-360, also fits Chain Saw models: 08 and 08S.
590-156 4223-030-0400
Crankshaft Assembly For Cut Quik Saw model: TS400.
590-157 4238-030-0400Crankshaft AssemblyFits Cut Quik / Concrete sawmodels:TS410 and TS420.
592-109 9503-003-0540Bearing - Crankshaft Fits chain saw models: 051 and 075 - (clutch side)Size: 20mm ID X 47mm OD X 14mm HT. (Bearing# 6204/C3) Open both sides
593-102 9503-003-0310Bearing - CrankshaftFits chain saw model: 041 - (flywheel side)Size: 15mm ID X 32mm OD X 9mm HT.(Bearing# 6002/C3) Open both sides
592-107 9503-003-03519503-003-03589503-003-0360
Bearing - CrankshaftFits Concrete saw / Cutquik saw models:TS410 and TS420. Grooved Ball Bearing.Size: 15mm (.587”) ID X 36.3mm (1.428”) OD X 11mm (.428”) HT. Open both sides. NOTE: These bearing will NOT fit on the “Z” TS410 & TS420 models.(Use with our 590-157 crankshaft assembly).
593-103 9503-003-04409503-003-0450
Bearing - CrankshaftFits Stihl chain saw models: (flywheel side) 038, 038 Super, 038 Magnum, 051, 075 and TS-510 and TS-400 (recoil side) cut quik saws. Also Stihl TS480i, TS500i, TS700 and TS800 Cutquik saws.Size: 17mm ID X 40mm OD X 12mm HT.(Bearing# 6203/C3) Open both sides
16-55
STIHL continued STIHL continued
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
Gasket SetFits chain saw models:034, 036, MS340 and MS360.(Oil seals included (1) 622-241 (15mm ID X 29.6mm OD X 4mm) + (1) 622-226 (12mm ID X 20mm OD X 5mm).
Fuel Filter - In Tank Use with molded fuel lines. Fits chainsaw models: 034, 036, 038; Stihl Cut Quik / Concrete saw models: TS410 and TS420 Cutquik. Measures: 11/16” OD X 1-5/8” overall length.
Fuel Filter - In TankFor use with molded fuel lines.Fits chain saw models: 034, 036, 038,044, MS440, 046, MS460, 064, MS640, 066, MS660 etc. NOTE: Similar to our our 613-605 but larger diameter. Recommended for larger cc Stihl chain saws. etc. Measures: 1-3/4” overall length X 23mm diameter.
610-125 1123-358-77011123-358-7702
Molded Fuel Line Fits chain saw models: 021, 023, 025, MS210, MS230, MS250.Note: Designed to be used with engines manufactured before January 2012; Not to be used with engines manufactured after January 2012.
610-123 1121-358-7700
Molded Fuel LineFits chain saw models:024, 026, MS 240 and MS 260.
Molded Fuel Line For chain saw models:034, 034 Super and 036 (previous to serial number)X39108850; 038 series as well as model 064 (previous to serial number X19512349.) Measures: 4-3/4” Long
550-161 1130-350-0500Fuel Cap Fits Stihl chain saw models:017, 018, 019, MS170, MS180,MS190, MS190 T and MS191 T.
550-120 1110-350-0502Fuel Cap For chain saw models: 041, 051 and 075.
550-145 0000-350-05201117-350-0500
Fuel & Oil Cap (40mm) Gas Cap for chain saw models: 020, 021, 023, 024, 025, 026,028, 028 Super, 029, 034, 034 Super, 036, 038 series, 039, 044, 046, MS290, MS310 and MS390. Oil Cap for Stihl chain saw models: 044, 046, 050, 064, 084, MS640, MS650 and MS660.
550-158 0000-350-0531 / 1124-350-0500Fuel Cap For chain saw models: 064, 066, MS660 and 084. Thread OD: 1.54” or 39.06mm
16-58
STIHL continued STIHL continued
Small Engine Parts & Accessories CHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
550-121 1107-350-0500Fuel Cap For chain saw models: 08, 070, 090 and Cut Quik models: TS-350 & TS-360.
551-149 0000-350-05101117-640-3600
Oil Cap and Fuel Cap (30mm) For chain saw models: 009, 010, 011, 012, 020, 021, 023, 024, 025,026, 028, 028 Super, 032, 034, 034 Super, 036, 038, 042 and 048. Fuel Cap for chain saw model: 048.
551-155 0000-350-0526Oil Cap For chain saw models: HT 100, HT 101, HT 130, HT 131, HT 250,HT 70, HT 73, HT 75, HTE 60, HT-KM.Gas CAP For the following models: 021, 023, 025, 026, 034, 036, 036QS, MC 200, MS 171, MS 181/C, MS 192/C/T, MS 200/T, MS 210/C, MS 211, MS 230/C, MS 240, MS 250/C, MS 260/C, MS 340, MS 360/C and MS 381.(Flip Top Style). Size: O-Ring Seal OD = 1.20”.
Fuel Cap / Gas Cap For Stihl concrete / cut quik saw model: TS400. Note: NOT compatible with > 10% ethanol fuel.
627-038 1119-640-71001119-642-1501
Oil Pump Spur Gear & Oiler Worm Gear Set for Stihl. Includes (1) oil pump spur gear (Replaces Stihl# 1119-642-1501). This nylon gear drives the oiler gear on saw & fits Stihl chainsaw models: 038, MS380 & MS381 ONLY. Also included is (1) oiler worm gear (Replaces Stihl# 1119-640-7100). This nylon sprocket comes complete with bushing attached. It drives the oiler and fits on Stihl chainsaw models: 038, MS380, MS381 as well as 028, 042 and 048 models.
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
600-402 1123-400-1301Electronic Coil Fits chain saw model: Most MS210 C-BE Z,MS230 C-BE Z and MS250 C-BE Z.(NOTE: Please verify the O.E.M. to enginemodel as part does not fit all applications!).
600-358 0000-400-1300
Electronic Ignition For chain saw models: 024, 026, 028, 028WB, 029, 034,034AV, 036, 038, 039, 044, 048, 064, MS240, MS260, MS290, MS310, MS340,MS360, MS380, MS381, MS390, MS440 and MS640; also Trimmer models: FS360 and FS420.
600-406 1122-400-1314
Electronic Ignition. Fits on Stihl chain saw models: 046, 066, MS460, MS650 and MS660
600-400 4223-400-1301 4223-400-1302 4223-400-1303
Ignition CoilFor concrete / cut quik saw.Fits model: TS400. Two bolt style (bolts not included). Coil comes complete with 13” of 5mm coil wire.
600-100Ignition Coil and Core For chain saw models: 08 and 08S. NOTE: Found on other equipment using theold 08 style power plant. ie: Stihl auger etc.
430-027 1100-430-02021110-430-02101121-430-0200
Stop Switch Kill Switch for chain saw models: 024, 026, 070 and Cut Quik Saw models 08S, TS-350 and TS-360. Measures: 3/4” X 1” X 1-1/2”
430-017 Universal Type
Toggle Kill Switch Kill switch found on many small older Chain Saw models with spade terminal wire end.
636-125 1125-140-0604
Muffler / Exhaust For chain saw models: 021, 023, 025,MS210,MS230 and MS250.
636-150 1121-140-0606
Muffler / Exhaust For chain saw models: 024, 026 and MS260.
636-152 1127-140-0605
Muffler / Exhaust For chain saw models: 029, 039, MS290, MS310 and MS390.
636-151 1125-140-06071125-140-06091125-140-6111
Muffler / Exhaust For chain saw models: 036, MS360and will fit some 034 Super models - see measurements. (You may need aspacer on some 034 models). Mountingbolt holes measure: 1.69” / (43mm) center to center / bolt holes measure: 7.3mm OD. Depth: 3” approximately.
636-297 1110-140-0613
Muffler / Exhaust For chain saw models: 040, 041 and 041G. (Uses our 623-157 exhaust gasket)
(2) 6mm none-threaded mounting holes at bottom of muffler on 93mm centers. Front cover held on with two screws - see picture on-line. OVERALL HEIGHT OF FRONT COVER = 95mmapproximately.(Uses our 623-132 exhaust gasket).For older 038 series see our 636-139 muffler.
Muffler / Exhaust For chain saw models:038 and 038 Super.
(2) 6mm none-threaded mounting holes at bottom of muffler on 93mm centers. Front cover held on with one screw mounted in the center. OVERALL HEIGHT OF FRONT COVER = 90mmapproximately. (Uses our 623-132 exhaust gasket).
16-60
STIHL continuedSTIHL continued
Small Engine Parts & Accessories CHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
623-132 1117-149-0601 1115-149-0601
Chainsaw Exhaust Gasket For chain saw models: 038 series.
636-154 1128-140-06121128-140-0616
Muffler / Exhaust Dual port muffler for chain sawmodels: 044, 046, MS440 & MS460. This is an aftermarket muffler. The dual port design add power. Complete with front baffle and spark arrester screens.
636-156 1122-140-0614
Muffler / Exhaust Single Port mufflerfor chain saw models: 066, MS660 & MS650.
636-153 1122-140-06131122-140-0800
Muffler / ExhaustDual Port muffler for chain saw models: 066, MS660 and MS650. (Also see our 636-156)
636-117 1108-140-0600
Muffler / Exhaust For models:08 and 08S. Note: Front and back images shown for reference.
636-171 4201-140-06074201-149-0601
Muffler / Exhaust For Cut Quik Saw models: TS350 and older TS360. NOTE: photo shows front and back images.(While Quantities Last)
636-173 4223-140-0601
Muffler / Exhaust For Cut Quik / Concrete Sawmodel: TS400.
622-226 9640-003-1190Oil seal For chain saw models: 020, 024,026, 034, 036, MS360, FS220, and 280. Size: 12mm X 20mm OD X 5mm.
622-233 9640-003-13409640-006-1314
Oil seal For chain saw models: 028, 030, 031, 032, 038, MS380, MS381 (Magneto side). Trimmer models: FS360, FS420, FS500 and FS550 and Blower models: BR 320, BR 340 L, BR 380, BR 400, BR420, BR420 C, SR 320, SR 400, SR 340 and SR 420.Size: 13mm X 22mm OD X 5mm
622-262 9640-003-1355Oil Seal Fits chain saw models: 046, MS460, 064, MS640.Size: 13.5mm X 20mm OD X 4mm. NOTE: You will need to confirm the measurements of your old seal to see if they match.
622-260 9642-003-1440 Oil Seal Fits chain saw models: 050, 051, 075 & 076and Cut Quik models: TS510 and TS760.Size: 14mm X 20mm OD X 3.5mm.
622-263 9640-003-1560 Oil Seal (Flywheel side) Fits chain saw models:039, 064, 066, MS 261, MS 341, MS 361,MS 362, MS 441, MS 650, MS 660 and MS 661 andCut Quik / Concrete Saw models: TS 410 and TS 420.Size: 15mm X 22mm OD X 4mm.NOTE: You will need to confirm themeasurements of your old seal to see if they match.
622-274 9640-003-1570 Oil Seal (Flywheel / Mag side) Fits chain saw models:041, 042, 048, 051, 075 & Cut Quik models:TS400, TS410, TS420, TS480i, TS500i, TS510 and TS760.Size: 15mm X 24mm OD X 7mm.
622-241 9640-003-1600
Oil Seal (Clutch Side). Fits chain saw models: 024, 026, 028, 034, 036, 044, 046, 084, MS 240, MS 241, MS 260, MS 261, MS 340, MS 341, MS 360, MS 361, MS 362, MS 440, MS 441, MS 460 and MS 461. Trimmer models: FS360, FS420, FS500, FS550 and SR400. Stihl Blower models: BR 320, BR 340, BR 380, BR 400, BR 420 blowers; Cut Quik saw model: GS 461; Stihl Sprayer models: SR 320, SR 340, SR 400 and SR 420. Size: 15mm X 29.6mm OD X 4mm HT. NOTE: You can find (1) 622-241 oil seal in our 640-268 gasket set.
16-61
STIHL continuedSTIHL continued
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
622-249 9640-003-1610Oil Seal (PTO & Mag side)Fits chain saw models: 08 / 08S & Cut Quik models: TS350and TS360.Size: 15mm X 35mm X 7mm.
622-261 9639-003-1743Oil Seal Fits chain saw models:029, 039, MS 290, MS 310 and MS 390.Size: 16.7mm ID X 30mm OD X 4.2mm HT.
622-076 9640-003-1745Oil Seal (Magneto and PTO Side)Fits concrete / cut quik saw models:TS400, TS460, TS700 and TS800.Size: 17mm ID X 28.15mm OD X 5mm Thick.
622-264 9640-003-1850 Oil Seal (Clutch side) Fits chain saw models:064, 066, MS650 and MS660.Size: 17mm X 32.9mm OD X 3.6mm.NOTE: You will need to confirm themeasurements of your old seal to see if they match.
622-266 9640-003-1880Oil Seal (PTO side) Fits chain saw models: 038 and 038 Super. Size: 17mm X 39.5mm OD X 5mm
622-257 9629-003-2900Oil Seal Fits chain saw models: 050, 051, 075 & 076and Cut Quik models: TS510 and TS760.Size: 25mm X 47mm OD X 7mm.
615-514 0000-350-6202 1130-350-6200
Primer Bulb AssemblyFound on concrete / cut off saw models:TS400 and TS800; Mounting hole: .576”(Uses our 615-028 replacement primer bulb).
615-510 4238-350--6201Primer Bulb AssemblySize: 1” OD X 1-3/8” HT.Found on Stihl concrete / cut off saw models:TS410 and TS720. Fits Stihl Blower models:BR350, BR430 and SR350, SR430, SR450.Mounting hole: .890”(Uses our 615-028 replacement primer bulb).
Spark Plug Wire (5mm OD)Plug Wire for chain saw models: 08, 08S and Cut Quik Saw models:TS-350 and TS-360. Quality black hypolon outer case with COPPER (not carbon) inner wire. 5mm Spark (Priced and Sold in 10 meter / 33 FT rolls)
650-141 1118-648-04001119-648-0400
Sprocket Side CoverFor chain saw models: 024 and 028 (new).
650-124 1108-640-1705Sprocket Side CoverFor chain saw models: 08 and 08S. Complete with tank cover.
681-134Sprocket Needle BearingFits chain saw models: 009, 010, 011, 012, 021, 023, 024, 025, 026, 34 and 36 (PRIOR TO X25809074). (Size: 10mm X 13mm X 10mm) NOTE: This bearing will not replace the plastic needle bearing type used on newer models.
681-128Sprocket Needle Bearing Fits models: 028 series.(Size: 10mm X 13mm X 23mm)
681-125 0000-993-3008
Sprocket Needle Bearing For chain saw models: 08S and Cut-Quik models: TS350 and TS360. (Size: 15mm X 18mm X 17mm) NOTE: This bearing will not replace the plastic needle bearing type used on newer models.
681-127Sprocket Needle Bearing Fits chain saw models:038. 042, 048 (Spur Only)(Size: 12mm X 16mm X 24mm)
(While Quantities Last)
16-62
STIHL continued STIHL continued
Small Engine Parts & Accessories CHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
681-126 9512-933-2382
Sprocket Needle Bearing Fits chain saw models: 044, 046, MS440,MS460, 064, 066, MS360, MS361, MS362,MS440, MS441, MS460, MS461, MS640 and MS660. NOTE: Will also replace the original STIHL (plastic cased needle bearing) in the MS390. (Size: 10mm X 16mm X 12mm)
681-129Sprocket Needle BearingFits our chain saw sprockets fitting on models: 084, 088. (Size: 12mm X 17mm X 13mm)
671-110
Sprocket Nut Fits chain saw models: 08, 08S; also found on older Cut Quik model: TS350
672-110Flywheel Nut Fits chainn saw models: 08, 042, 045, 056, 070, 090; also found on Cut Quik models: TS350 & TS360
CE4MC56 3670-005-0056(Rotary# 7111056)
Saw Chain Loop (10” Bar)1/4” pitch X .043 gauge X 56 drive link count
Fits STIHL battery powered chainsawsand pole saws, using a 10” guide bar.Used on Stihl model: MS150 TC-E etc.(Replaces Stihl# 3670 005 0056 / 71PM3-56).
CE4MC64 3670-005-0064(Rotary# 7111064)
Saw Chain Loop (12” Bar)1/4” pitch X .043 gauge X 64 drive link count
Fits STIHL battery powered chainsawsand pole saws, using a 12” guide bar.Used on Stihl model: MS150 TC-E etc.(Replaces Stihl# 3670 005 0064 / 71PM3-64).
CE4MC72 3670-005-0072(Rotary# 7111072)
Saw Chain Loop (14” Bar)1/4” pitch X .043 gauge X 72 drive link count
Fits STIHL battery powered chainsawsand pole saws, using a 14” guide bar.Used on Stihl model: MS150 TC-E etc.(Replaces Stihl# 3670 005 0072 / 71PM3-72).
(While Quantities Last)
655-025 1123-080-2104
Starter Assembly For chain saw models:021, 023, 023, MS210, MS230 and MS250. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawl, handle etc. Just needs to be bolted on.(Made of Nylon).
655-024 1121-080-2101
Starter Assembly For chain saw models:024, 026, MS240and MS260.
This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawl, handle etc. Just needs to be bolted on.(Made of Nylon).
655-029 1127-080-2103 / A
Starter Assembly For chain saw models:029, 031, 039, MS290,MS310, MS390.
This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawls, handle etc. Just needs to be bolted on. (Made of Nylon).
This aftermarket assembly comes complete with housing,starter pulley, spring, rope, pawls, handle etc. Just needs to be bolted on. (Made of metal).
655-036 1135-080-2102
Starter AssemblyFor chain saw models:MS341 and MS361.
This aftermarket assembly comes completewith plastic housing, starter pulley, spring, rope,pawl, starter handle etc. Just needs to be bolted on.
16-63
STIHL continued STIHL continued
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
STIHL continued STIHL continued
655-038 1119-080-1800
Starter Assembly For chain saw models:038 series.
This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawls, handle etc. Just needs to be bolted on. (Made of cast metal).
Starter Assembly For chain saw models:044, 046, MS440and MS460.
This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawls, handle etc. Just needs to be bolted on. (Made of cast metal).
655-066 1122-080-2110
Starter Assembly For chain saw models:066, MS650 andMS660.
This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawls, handle etc. Just needs to be bolted on. (Made of cast metal).
655-035 1108-080-2101 / 1108-080-2115
Starter Assembly For chain saw model: 08 & 08S and Concrete/ Cut Quik saw model:TS350 and older TS360.
This aftermarket assembly comes complete with plastic housing, metal starter pulley, spring, rope, pawl, elasto starter handle etc. Just needs to be bolted on. (This assembly is the newer - 1 nylon starter pawl set up).
655-040 4223-190-0401
Starter Assembly For concrete saw / cut quik saw model: TS400. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawl, handle etc. Just needs to be bolted on. (Made of Nylon)
Starter AssemblyFor concrete saw cut quik saw models: TS410 and TS420.This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawl, handle etc. Just needs to be bolted on. (Made of Nylon)
560-119Starter Handle For chain saw models: 010, 011, 015,021, 028, 031 and 032.
560-213 1121-195-3400
Starter Handle For chain saw models: 021, 023, 024, 026, 028,028 Super, 034, 034 Super, 036,044, 046, 064, 066 (New style),Concrete saw models: TS350, TS360, TS510 and TS360
Elasto Starter Handle and RopeFor many Stihl saws. Medium starter handle with rubber buffer to help obsorb the kick that you get from some of the larger cc saws. Rope diameter is 4mm X 36 inches long.
560-121 1122-190-3400Elasto Starter Handle and Rope For many Stihl saws.Large starter handle with rubberbuffer to help obsorb the kick thatyou get from some of the larger cc saws. Rope diameter is 4.5mm X 38 inches long.
560-170 1117-195-7200Starter Pawl (nylon)For Stihl chain saw models: 08, 038, 042, 048, 051, 056 and 070 (old style). Size: 1.11” overall length X
.375” overall height not including positioning nub.
(Sold in multiples of 10)
(Sold in multiples of 10)
(Sold in multiples of 10)
16-64
Small Engine Parts & Accessories CHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
560-202 1124-195-04011124-195-7200
Starter Pawl (nylon)For Stihl chain saw models: 038, 041, 042, 045, 048, 050, 051, 056, 064, 066, 070, 076, 08S, 084, 088, MS380, MS640, MS650, MS660, MS880; also fits Cut Quik Saw models TS350 and TS360.Size: 1.12” overall length X .475” overall height not including positioning nub. (newer style)
Starter Pawl (metal pin)Fits concrete saw model: TS400
560-199 4116-195-7200Starter Pawl (nylon)Fits Trimmer models:FR220, FS106, FS160, FS180,FS220, FS280; Back Pack Blowersmodels: BR320, BR320L, BR340, BR340L,BR380, BR400, BR420, BR500, BR550, BR600,2 cycle Tillers and more.(For use with our 630-095 pawl spring).
630-095 1118-195-3500Spring Clip / Pawl Spring Fits chain saw models: 009, 010,011, 012, 024,026, 028, 032 old style;Also found on Trimmers, Blowers, 2 cycle Tillers and more. (For use with our 560-111 and 560-199 starter pawls).
630-111 1128-195-3500Spring Clip / Pawl Spring Fits chain saw models: 024, 026, 028, 034, 036, MS360, 039, MS390, 044, MS440, 046, MS460 etc. (For use with our 560-203 starter pawls).
630-118 1124-195-3500Spring Clip / Pawl Spring Fits chain saw models: 064, 066, MS640, MS660 and 084. Size: 1-3/4” overall length X 1-1/8” approximately(For use with our 560-202 starter pawls).
560-146 1107-190-1000Starter Pulley (metal)For chain saw models: 08, 08S and 070. Measures: 3” OD (2) pawl pulley
560-200 1122-195-0400
Starter Pulley (nylon)For chain saw models: 08S, 051, 064, 066, MS640, MS650 & MS660. Measures: 2-27/32” OD (2) pawl pulley
560-225 4223-190-1001
Starter Pulley With brass bushing.For Stihl Cut Quik / Cut off saw models:TS400, TS410 and TS420 Cutquik saws.Measures: 3” (76.82mm) Bottom OD X 2.74” (69.63mm) Top OD X .412 (10.47mm) ID / Bore. (1) pawl pulley. Uses our 560-784 Starter Pawl.
(While Quantities Last)
STIHL continued STIHL continued
16-65
Small Engine Parts & AccessoriesCHAIN SAW ACCESSORIES - O.E.MCHAIN SAW ACCESSORIES - O.E.M
C C
560-116 0000-961-5116Starter Ring (nylon)For chain saw models:08S, 041, 045 & 070. Size: 2-1/4” OD
Starter SpringFor chain saw models: 017, 018, 019 T, 020, 020 T, 021, 023,025, 029, 034, 036, 039, 044, 046,MS 170, MS 171, MS 180, MS 181,MS 190 T, MS 191 T, MS 200, MS 200 T, MS 210,MS 211, MS 230, MS 250, MS 270, MS 280, MS 290, MS 310, MS 340, MS 360, MS 390, MS 440, MS 460. Replacement spring for our 655-034 & 655-044 starter assemblies.