Category_7_File_12 Spec Các Loại Sơn

( II ) INDUSTRIAL & PROTECTIVE SYSTEM

(A) ALKYD BASE

QUICK PAINT AUTO GLOSS PAINT GLOSS PAINT VARNISH TOP WOOD VARNISH ALUMINUM TOP RED OXIDE ZINC CHROMATE PRIMER RED OXIDE PRIMER AUTO GLOSS ZINC CHROMATE PRIMER RED LEAD PRIMER WASH PRIMER (2 PACK ETCH PRIMER) WASH PRIMER (1 PACK ETCH PRIMER) ROAD MARKING BLACK BOARD FLUORESCENT PAINT REMOVER

(B) AUTOMOTIVE PAINTS SYSTEM

(B-1) NITROCELLULOSE PAINTS FLEX PUTTY FLEX PRIMER SURFACER FLEX PAINT TOP COAT

(B-2) ACRYLIC NCR CRYL NCR PUTTY CRYL NCR PRIMER CRYL NCR PAINT ACRYLIC THINNER

(B-3) NUMIX SYSTEM NUMIX CLEANER NUMIX PU PRIMER 2K NUMIX PRIMER 1K NUMIX ADHESION PROMOTER NUMIX HARDENER PRIMER NUMIX TOP COAT 2K NUMIX BASE COAT 1K NUMIX CLEAR COAT 2K NUMIX HARDENER NUMIX THINNER NUMIX RETARDANT THINNER NUMIX ANTI SILICON NUMIX SPOT REPAIR THINNER NUMIX PLASTICIZER NUMIX MA-4 MATTING PASTE

(B-4) MISCELLANEOUS FAST CUT POLISH SOFT POLISH GRAVEL GUARD (GOMA)

(C) FURNITURE & WOOD FINISH PAINTS

(C-1) NITROCELLULOSE PAINTS FLEX CLEAR COAT LACQUER TOP CLEAR COAT LACQUER FLEX SANDING SEALER TOP SANDING SEALER N.C WOOD STAIN N.C THINNER

(C-2) ACRYLIC POLYURETHANE POLYURETHANE SANDING SEALER POLYURETHANE CLEAR COAT ACID CURING

(D) STOVING SYSTEM

ALKYD MELAMINE STOVING PAINT ACRYLIC STOVING PAINT SILICONE STOVING PAINT TIN PLATE LACQUER

(E) EPOXY SYSTEM

EPOXY INTERMEDIATE HB 2.19 EPOXY ZINC RICH PRIMER HB 10.03 GUARD EPOXY SF EPOXY ZINC PHOSPHATE PRIMER 10.06

(A) ALKYD BASE

QUICK PAINT AUTO GLOSS PAINT GLOSS PAINT VARNISH TOP WOOD VARNISH ALUMINUM TOP RED OXIDE ZINC CHROMATE PRIMER RED OXIDE PRIMER AUTO GLOSS ZINC CHROMATE PRIMER RED LEAD PRIMER WASH PRIMER (2 PACK ETCH PRIMER) WASH PRIMER (1 PACK ETCH PRIMER) ROAD MARKING BLACK BOARD FLUORESCENT PAINT REMOVER

QUICK PAINT DESCRIPTION A quick drying gloss enamel, based on a special Alkyd, which gives an

excellent, tough and flexible finish that has good adhesion and weather resistance.

RECOMMENDED USE Metal work for interior and exterior applications, heavy duty equipment, vehicles, special military purposes and radiators, etc.

TECHNICAL INFORMATION Colors As per shade card. Finish Glossy. Viscosity (25C) 8.5 - 9.5 Poise Specific Gravity 1.08 0.1 (for White and Pastel shades). Solid by Weight % 62 5% Coverage Rate (2 coat 10% dilution)

3 - 6 m2/Lit. (depending on the color used).

Drying time Touch dry : 1 hr. Recoatable: 4 hrs.

Flash point 30C

APPLICATION DATA Application Methods Spray. Thining / Cleaning of Tools National Synthetic Thinner. Film Thickness (D.F.T.) 30 microns 1.2 mils.

(W.F.T.) 60 microns 2.4 mils. Guiding Data for Airless Spray Nozzle Tip: 0.015" - 0.02"

Nozzle Pressure: 2200 P.S.I.

SURFACE PREPARATION Surface should be cleaned thoroughly and should be dry and free from dust.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 24 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

AUTO GLOSS PAINT DESCRIPTION A special Alkyd base quick drying and glossy finish which is hard and

weather resistant, its high gloss does not require any polishing. RECOMMENDED USE Suitable for Interior / Exterior and all wooden, masonry and metallic

surfaces specially heavy duty equipment.

TECHNICAL INFORMATION Colors As per shade card. Finish Glossy. Viscosity (25C) 7.5 - 8.5 Poise. Specific Gravity 1.07 0.1 (for White and Pastel shades). Solid by Weight % 60 5% Coverage Rate (2 coat 10% dilution)

4 - 8 m2/Lit. (depending on the color used).

Drying time Touch dry : 1 hr. Hard dry : 3 hrs.

Flash point 32C

APPLICATION DATA Application Methods Spray Thining / Cleaning of Tools National Special Thinner. Mixing Ratio 7.5% hardener maybe added to improve performance. Film Thickness (D.F.T.) 30 microns 1.2 mils.

(W.F.T.) 60 microns 2.4 mils. Guiding Data for Airless Spray Nozzle Tip: 0.015" - 0.02".

Nozzel Pressure: 2200 P.I.S.

SURFACE PREPARATION Surface should be cleaned and dry thoroughly and should be applied over National N.C. Putty or National N.C Primer.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 24 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

GLOSS PAINT DESCRIPTION An Alkyd base quick drying glossy finish which has high impact

resistance and gloss.

RECOMMENDED USE Special paint for trucks and heavy duty equipment.

TECHNICAL INFORMATION Colors All major colours for trucks. Finish Glossy. Viscosity (25C) 7.5 - 8.5 Poise Specific Gravity 1.09 0.1 Solid by Weight % 62 5% Coverage Rate (2 coat 10% dilution)

3 - 6 m2/Lit. (depending on the color used).

Drying time Touch dry : 2 hrs. Recoatable: 3 - 4 hrs.

Flash point 32C

APPLICATION DATA Application Methods Spray. Thining / Cleaning of Tools National Synthetic Thinner. Film Thickness (D.F.T.) 30 microns 1.2 mils.

(W.F.T.) 60 microns 2.4 mils. Guiding Data for Airless Spray Nozzle Tip: 0.015" - 0.02".

Nozzle Pressure: 2200 P.S.I.

SURFACE PREPARATION Surface should be dry and free from dust and to be applied over National N.C. Putty or National N.C Primer.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 24 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

VARNISH DESCRIPTION A high quality synthetic Varnish for both exterior and interior use which

gives a hard, tough, glossy finish resistant to water, oils, etc. RECOMMENDED USE Interior and Exterior, for soft wood, hard wood, doors, windows and

furniture, also as a glaze coat for enamels.

TECHNICAL INFORMATION Colors Transparent, Clear. Finish Glossy. Viscosity (25C) 8.5 - 9.5 Poise. Specific Gravity 0.90 0.02 Solid by Weight % 58 2% Coverage Rate (2 coat 10% dilution)

10 - 12 m/Lit.

Drying time Touch dry : 6 hrs. Recoatable: 18 hrs.

Flash point 38C

APPLICATION DATA Application Methods Brush, Roller or Spray. Thining / Cleaning of Tools White Spirits as needed 15 - 25%. Film Thickness (D.F.T.) 25 microns 1 mils.

(W.F.T.) 50 microns 2 mils. Guiding Data for Airless Spray Nozzle Tip: 0.015 " - 0.020"

Nozzle Pressure: 2200 P.S.I.

SURFACE PREPARATION Surface should be dry and clean.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 24 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

TOP WOOD VARNISH DESCRIPTION It is especially satin gloss and matt transparent alkyd urethane

wood stain which can be applied over new wood substrates or old painted wooden surfaces. It has very good water repellency and can be used for interior and exterior wooden surfaces.

RECOMMENDED USE Interior & exterior wood substrate.

TECHNICAL INFORMATION Colors As per shade cards Finish Glossy & matt Specific Gravity 0.90 0.94 Solid by Weight % 52 2 Covering Rate 10 - 12 m/Lit. Drying Time Touch dry : 4 hrs.

Recoatable : 24 hrs.

APPLICATION DATA Application Methods Brush, fine nylon roller Thinning / Cleaning of Tools Ready to use /White spirit

SURFACE PREPARATION Before application, the surface should be sound, clean and free from oil, grease, loose particles, dust and applied as follows: Primer National Varnish 1 coat Top Coat National Top Wood Varnish 2 coats

CONDITIONS DURING APPLICATIONThe tempraure of the substrate should be minimum 10C above the dew point measured in the substrate vicinity.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 24 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

ALUMINUM DESCRIPTION A high luster reflective finish based on Aluminum pigment and special

hard resins, which can withstand temperature upto 500C. RECOMMENDED USE Steel work, Electric poles, Iron towers, Pipes, Radiators, Exhaust Pipes

etc

TECHNICAL INFORMATION Colors Aluminum, Silver. Finish Glossy, Reflective. Viscosity (25C) 30 36 secs. Specific Gravity 0.99 0.01 Solid by Weight % 52 2% Theoretical Spreading Rate 18 - 20 m/Lit. Drying time Touch dry: 1 - 2 hrs.

Hard dry : 18 hrs. Flash point 32C

APPLICATION DATA Application Methods Brush, Roller or Spray. Thining / Cleaning of Tools When required W.S. or Turpentine. Film Thickness (D.F.T.) 25 microns 1 mil.

(W.F.T.) 60 microns 2.4 mils. Guiding Data for Airless Spray Nozzle Tip: 0.015 - " 0.020"

Nozzle Pressure: 2200 P.S.I.

SURFACE PREPARATION Surface must be clean and free from dust.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 12 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

TOP RED OXIDE ZINC CHROMATE PRIMER DESCRIPTION An Alkyd / Zinc pigment base anticorrosive primer used as a general

purpose, corrosion resistant, protective primer.

RECOMMENDED USE Ferrous surfaces such as steel structure, metal works ect

TECHNICAL INFORMATION Colors Brown. Finish Flat, Matt. Viscosity (25C) 9.5 - 10.5 Poise Specific Gravity 1.32 0.02 Solid by Weight % 71 2% Coverage Rate (2 coat 10% dilution)

14 - 16 m/Lit.

Drying time Touch dry: 2 - 3 hrs. Recoatable: 12 hrs.

Flash point 38C

APPLICATION DATA Application Methods Brush, Roller or Spray. Thining / Cleaning of Tools White Spirits as needed. Film Thickness (D.F.T.) 40 microns 1.6 mils.

(W.F.T.) 80 microns 3.2 mils. Guiding Data for Airless Spray Nozzle Tip: 0.015 - " 0.020"

Nozzle Pressure: 2200 P.S.I

SURFACE PREPARATION Remove all corrosions, mill scale, dirt, oil, grease, etc, by blast cleaning, flame cleaning, scraping, wire brushing or any other suitable technique. Ensure surface is absolutely dry at the time of painting or else rust will form underneath the paint film.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 18 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

RED OXIDE PRIMER DESCRIPTION An Alkyd base general purpose anticorrosive primer.

RECOMMENDED USE Ferrous surfaces such as steel structures, metal works, etc

TECHNICAL INFORMATION Colors Red, Brown. Finish Flat, Matt. Viscosity (25C) 11 - 12 Poise (25C). Specific Gravity 1.46 0.02 Solid by Weight % 74.5 2% Coverage Rate (2 coat 10% dilution)

11 - 12 m/Lit.

Drying time Touch dry : 5 hrs. Recoatable: 18 hrs.

Flash point 38C

APPLICATION DATA Application Methods Brush, Roller or Spray. Thining / Cleaning of Tools White Spirits. Film Thickness (D.F.T.) 55 microns 2.2 mils.

(W.F.T.) 75 microns 3 mils. Guiding Data for Airless Spray Nozzle Tip: 0.015 - " 0.020"

Nozzle Pressure: 2200 P.S.I.

SURFACE PREPARATION Remove all corrosions, mill scale, dirt, oil, grease, etc, by blast cleaning, flame cleaning, scraping, wire brushing or any other suitable technique. Ensure surface is absolutely dry at the time of painting or else rust will form underneath the paint film.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 18 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

AUTO GLOSS ZINC CHROMATE PRIMER DESCRIPTION A very good anticorrosive primer based on Alkyd resins and Zinc

Chromate pigments. Used where extreme anticorrosion properties are required.

RECOMMENDED USE Suitable for steel surfaces where finishing coats are white or pastel shades.

TECHNICAL INFORMATION Colors Yellow, Yellowish Green. Finish Matt. Viscosity (25C) 7.5 - 8.5 Poise (25C). Specific gravity 1.27 0.02 Solid by Weight % 65 2% Theoretical Spreading Rate 15 - 17 m/Lit. Drying time Touch dry : 3 hrs.

Recoatable: 12 hrs. Flash point 32C

APPLICATION DATA Application Methods Brush, Roller or Spray. Thining / Cleaning of Tools National Thinner or 121. Film Thickness (D.F.T.) 30 microns 1.2 mils.

(W.F.T.) 60 microns 2.4 mils. Guiding Data for Airless Spray Nozzle Tip: 0.015 - " 0.020"

Nozzle Pressure: 2200 P.S.I.

SURFACE PREPARATION Remove all corrosions, mill scale, dirt, oil, grease, etc, by blast cleaning, flame cleaning, scraping, wire brushing or any other suitable technique. Ensure surface is absolutely dry at the time of painting or else rust will form underneath the paint film.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 18 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

RED LEAD PRIMER DESCRIPTION An Alkyd base primer containing Red Lead pigments, which gives

excellent rust preventing properties and is resistant to mild and moderate corrosive environments.

RECOMMENDED USE On Ferrous surfaces like steel structures, etc

TECHNICAL INFORMATION Colors Red, Orange. Finish Matt. Viscosity (25C) 20 - 22 Poise (25C). Specific Gravity 1.5 0.02 Solid by Weight % 80 2% Coverage Rate (2 coat 10% dilution)

12 - 15 m/Lit.

Drying time Touch dry : 5 hrs. Recoatable: 24 hrs.

Flash point 38C

APPLICATION DATA Application Methods Brush, Roller or Spray. Thining / Cleaning of Tools White Spirits. Film Thickness (D.F.T.) 45 microns 1.8 mils.

(W.F.T.) 75 microns 3 mils. Guiding Data for Airless Spray Nozzle Tip: 0.015 - " 0.020"

Nozzle Pressure: 2200 P.S.I.

SURFACE PREPARATION Remove all corrosions, mill scale, dirt, oil, grease, etc, by blast cleaning, flame cleaning, scraping, wire brushing or any other suitable technique. Ensure surface is absolutely dry at the time of painting or else rust will form underneath the paint film.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 18 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

WASH PRIMER {2 PACK ETCH PRIMER}

DESCRIPTION A fast drying protective coating based on Polyvinyl Butyral resin/Zinc Chromate pigment/Phosphoric acid, which combines pretreatment and priming in one application, for non-ferrous metals to ensure good adhesion of subsequent coats.

RECOMMENDED USE Aluminum cladding, Galvanized surfaces, Brass etc.

TECHNICAL INFORMATION Colors Yellow, Green. Finish Flat Viscosity (25C) 18 - 22 Poise. Specific Gravity 1.05 0.05 Solid by Weight % 39 2% Coverage Rate (2 coat 10% dilution) 16.0 m/Lit. @ 8 microns (D.F.T.). Drying time Touch dry : 15 min.

Recoatable: 1 hr. Flash point 13C

APPLICATION DATA Application Methods Brush, Roller or Spray. Mixing Ratio Add hardener and mix.

Green Primer 1:1 hardener. Yellow primer 1:1 hardener.

Thining / Cleaning of Tools National Thinner. Salt Spray & Humidity Resistance Excellent (500 hours). Film Thickness (D.F.T.) 16 microns 0.64 mils.

(W.F.T.) 60 microns 2.4 mils. Guiding Data for AirlessSpray Nozzle Tip: 0.009 - " 0.011"

Nozzle Pressure: 1500 - 2000 P.S.I.

SURFACE PREPARATION Degrease surface, wet abrading with abrasive paper.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 18 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

WASH PRIMER {1 PACK ETCH PRIMER}

DESCRIPTION A fast drying protective coating based on Polyvinyl Butyral resin/Zinc Chromate pigment/Phosphoric acid, which combines pre-treatment and priming in one application, for non-ferrous metals to ensure good adhesion of subsequent coats.

RECOMMENDED USE Aluminum cladding, Galvanized surfaces, Brass etc.

TECHNICAL INFORMATION Colors Yellow, Green. Finish Flat Viscosity (25C) 18 - 22 Poise. Specific Gravity 1.05 0.05 Solid by Weight % 39 2% Coverage Rate (2 coat 10% dilution)

16.0 m/Lit. @ 8 microns (D.F.T.).

Drying time Touch dry : 15 min. Recoatable: 1 hr.

Flash point 13C

APPLICATION DATA Application Methods Brush, Roller or Spray. Thining / Cleaning of Tools National Thinner. Film Thickness (D.F.T.) 16 microns 0.64 mils.

(W.F.T.) 60 microns 2.4 mils. Guiding Data for AirlessSpray Nozzle Tip: 0.009" - 0.011"

Nozzle Pressure: 1500 - 2000 P.S.I.

SURFACE PREPARATION Degrease surface, wet abrading with abrasive paper.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 18 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

ROAD MARKING DESCRIPTION An Alkyd Resin and chlorinated rubber base road marking paint have

fast drying, high abrasion resistance and good durability to severe weather conditions.

RECOMMENDED USE For use on concrete or asphalt roads, curbstones, runways, etc.

TECHNICAL INFORMATION Colors White, Yellow, Black. Finish Smooth & Matt. Viscosity (25C) 11.5 - 12.5 Poise. Specific Gravity 1.45 0.05 Solid by Weight % 70 5% Theoretical Spreading Rate 3 - 5 m2/Lit. Drying time Touch dry: 15 - 20 min.

Hard dry : 2 - 4 hrs. Flash point 35C

APPLICATION DATA Application Methods Brush, Spray, Roller. Thining / Cleaning of Tools Ready for use, could be diluted by National Synthetic Thinner. Film Thickness (D.F.T.) 100 microns. Guiding Data for AirlessSpray Nozzle Tip: 0.015" - 0.20"

Nozzle Pressure: 2200 P.S.I.

SURFACE PREPARATION Surface must be clean, dry and free from oil, grease, dirt etc.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 18 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

BLACK BOARD DESCRIPTION A Special Alkyd / Hard Resin base paint having good adhesion, high

coverage, fast drying, good scratch resistance towards slippage of chalk during writing and easily cleanable.

RECOMMENDED USE On wood and masonry, school boards as a finish coat.

TECHNICAL INFORMATION Colors Black & Green. Finish Matt. Viscosity (25C) 7.5 - 8.5 Poise. Specific Gravity 1.32 0.05 Solid by Weight % 65 5% Theoretical Spreading Rate 10 - 12 m2/Lit. Drying time Touch dry: 4 hrs.

Hard dry : 24 hrs. Ready to be used: after 3 days.

Flash point 38C

APPLICATION DATA Application Methods Brush, Spray, Roller. Thining White Spirits as required. Guiding Data for AirlessSpray Nozzle Tip: 0.015" - 0.20"

Nozzle Pressure: 2200 P.S.I.

APPLICATION SYSTEM - One Coat of National Undercoat. - Two Coats of National Black Board.

SURFACE PREPARATION Surface must be clean and dry.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 18 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

FLUORESCENT DESCRIPTION An Acrylic base high visibility and good reflective finish.

RECOMMENDED USE Excellent product for painting road signs.

TECHNICAL INFORMATION Colors Red, Orange Yellow and Green. Viscosity (25C) 8 - 10 Poise. Specific Gravity 1.10 0.05 Solid by Weight % 50 2% Theoretical Spreading Rate 15 m2/Lit. Drying Time Touch dry: 30 min.

Hard dry : 6 - 8 hrs.

APPLICATION DATA Application Methods Spray, Roller, Brush. Thinner National Thinner. Film Thickness (D.F.T.) 35 microns.

(W.F.T.) 70 microns. Guiding Data for Airless Spray Tip Size: 0.432 - 0.482 mm.

Line Pressure: 110 - 140 Bar. Fan Size: 60 - 80C

SURFACE PREPARATION Surface must be clean and dry.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 18 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

PAINT REMOVER DESCRIPTION A highly effective medium base mixture of solvents and additives

suitably thickened to give fast, effective and safe paint removing property. Used for removing all types of dried paint films from type of surfaces. Can be used as brush cleaning agent.

RECOMMENDED USE On Concrete, Plaster, Wood or Metal surfaces.

TECHNICAL INFORMATION Colors Transparent. Viscosity (25C) 9 - 10 Poise. Specific Gravity 1.19 0.05 Solid by Weight % 5 1% Theoretical Spreading Rate Various depending on surface, type of paint, paint film thickness etc.

APPLICATION METHOD - Lay thick coat of undiluted paint remover on the old paint film, leave for 20 minutes for reacting until

wrinkles emerge on the surface. - Remove the soften film along with excess chemical with hard tool. - If the film is thick or hard it may be necessary to repeat the process. - After fully removing the loosened paint film and chemical with a hard tool, wash the surface with

water.

SPECIAL PRECAUETION Use hand gloves. Do not allow National Paint Remover to come in contact with skin, in case of any accidental skin contact wash the affected areas thoroughly with fresh water.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 12 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

(B) AUTOMOTIVE PAINTS SYSTEM

(B-1) NITROCELLULOSE PAINTS FLEX PUTTY FLEX PRIMER SURFACER FLEX PAINT TOP COAT

(B-2) ACRYLIC NCR CRYL NCR PUTTY CRYL NCR PRIMER CRYL NCR PAINT ACRYLIC THINNER

(B-3) NUMIX SYSTEM NUMIX CLEANER NUMIX PU PRIMER 2K NUMIX PRIMER 1K NUMIX ADHESION PROMOTER NUMIX HARDENER PRIMER NUMIX TOP COAT 2K NUMIX BASE COAT 1K NUMIX CLEAR COAT 2K NUMIX HARDENER NUMIX THINNER NUMIX RETARDAND THINNER NUMIX ANTI SILICON NUMIX SPOT REPAIR THINNER NUMIX PLASTICIZER NUMIX MA-4 MATTING PASTE

(B-4) MISCELLANEOUS FAST CUT POLISH SOFT POLISH GRAVEL GUARD (GOMA)

(B-1) NITROCELLULOSE PAINTS FLEX PUTTY FLEX PRIMER SURFACER FLEX PAINT TOP COAT

FLEX PUTTY DESCRIPTION It is a special glazing putty based on Nitrocellulose / Alkyd for use on

wooden & steel surfaces.

RECOMMENDED USE As a body filler for automobiles and for leveling wooden surfaces.

TECHNICAL INFORMATION Colors Red, Red Brown, Grey, White, Black. Gloss (60) Matt. Viscosity (20C) Thick Viscosity. Specific Gravity 1.28 0.02 Solid by Weight% (110C) 55 1 % Covering Capacity 3 - 4 m2/Lit. (D.F.T. 30 ). Drying time Touch dry: 30 min.

Sanding Time: After 2 hrs. Hard dry : 3 4 hrs.

APPLICATION DATA Application Methods Glazing Knife. Thining / Cleaning of Tools National N.C Thinner. Film Thickness Single pack, ready to use. Guiding Data for Airless Spray Recommended 20 - 30 microns per coat (or as necessary depends upon

surface).

SURFACE PREPARATION To be applied over National N.C Primer and the primered surface should be dry, clean and free from any loose particles.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 18 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

FLEX PRIMER SURFACER DESCRIPTION It is a specially formulated Primer based on Nitrocellulose / Alkyd resins

for use on wooden and steel surfaces.

RECOMMENDED USE For use on furniture, automobiles, doors, office cabinets etc

TECHNICAL INFORMATION Colors Grey, White, Black, Yellow. Gloss (60) Matt. Viscosity (20C) 65 - 70 Poise. Specific Gravity 1.32 0.02 Solid by Weight% (110C) 55 1 % Covering Capacity 3 - 4 m2/Lit. (D.F.T 30 ). Drying time Touch dry: 30 min.

Sanding Time: After 2 - 3 hrs. Hard dry : 3 - 4 hrs.

APPLICATION DATA Method of application Spray. Thinning / Cleaning of Tools National N.C. Thinner. Mixing Ratio Single pack, dilution (1:1). Film Thickness D.F.T Recommended 15 - 30 microns per coat (or as necessary depends upon

surface). Guiding Data for Airless Spray Nozzle Orifice: 0.017" - 0.021"

Nozzle Pressure: 2000 - 2300 P.S.I.

SURFACE PREPARATION The surface should be dry, clean, and well rubbed down with sandpaper, free of any loose particles.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 18 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtai ned under controlled conditions. We reserve the right to change data without prior notice.

FLEX PAINT TOP COAT DESCRIPTION It is a fast drying excellent finish based on Nitrocellulose/Alkyd resins,

which has good color retention, durability and water resistance.

RECOMMENDED USE As a finish for automobiles and furniture etc

TECHNICAL INFORMATION Colors As per shade card. Gloss (60) Matt or Gloss. Viscosity (20C) Thick Viscosity. Specific Gravity 1.1 0.1 Solid by Weight% (110C) 45 1 % Covering Capacity 3 - 9 m2/Lit. (DFT: 30 ). Drying time Touch dry : 30 min.

Hard dry : 8 - 12 hrs. Recoatable : 3 - 4 hrs. for polishing.

APPLICATION DATA Method of application Spray. Thinning / Cleaning of Tools National N.C Thinner. Mixing Ratio Single pack, dilution (1:1). Film Thickness D.F.T Recommended 15 - 30 microns per coat (or as necessary depends upon

surface). Guiding Data for Airless Spray Nozzle Orifice: 0.017" - 0.021".

Nozzle Pressure: 2000 - 2300 P.S.I.

SURFACE PREPARATION To be applied over National N.C Putty or National N.C Primer as the case maybe, and can be over coated with National Clear Lacquer.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 24 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtai ned under controlled conditions. We reserve the right to change data without prior notice.

(B-2) ACRYLIC NCR CRYL NCR PUTTY CRYL NCR PRIMER CRYL NCR PAINT ACRYLIC THINNER

CRYL NCR PUTTY DESCRIPTION National Cryl NCR Putty is a two-component Putty, formulated with

high percentage of filler to cover all pores and give a smooth adequate touch.

RECOMMENDED USE For wood and steel surface.

TECHNICAL INFORMATION Colors White Finish Matt Viscosity (20C) Thick Paste. Specific Gravity 1.65 0.05 (of mix). Solid by Weight % 75 2 % Theoretical Spreading Rate 5 m/Lit. @ 40 microns (D.F.T.) Drying time Touch dry: 1 - 2 hrs.

Hard dry : Min : 3 hrs. (20C). Max: 6 hrs. (20C).

Flash Point 25C when mixed.

APPLICATION DATA Thinning / Cleaning of Tools National Thinner 204. Mixing Ratio Base: 100 parts by volume.

Curing Agent (hardener): 1.0 part by volume. Pot Life 6 8 hrs (20C).

SURFACE PREPARATION The surface should be clean and dry at the time of application and its temperature must be above the dew point to avoid condensation.

DRYING TIME For optimum Drying/Curing, good ventilation is always a recommendation. In oven: full curing needs 30 min. @ 60C.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

SHELF LIFE 18 months @ (20C) SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtai ned under controlled conditions. We reserve the right to change data without prior notice.

CRYL NCR PRIMER DESCRIPTION National Cryl NCR Primer is a two-component primer with excellent

sanding and high coverage. RECOMMENDED USE As a primer surfacer coat for protection of steel in severely corrosive

environment where gloss and color retention is required.

TECHNICAL INFORMATION Colors White, Grey. Finish Flat. Viscosity (20C) 15 - 30 Poise. Specific Gravity 1.37 0.05 (of mix). Solid by Weight % 68 2 % Theoretical Spreading Rate 9 m/Lit. @ 40 microns (D.F.T.). Drying time Touch dry : 1 - 2 hrs.

Recoatable: Min: 3 hrs. (20C). Max : 6 hrs. (20C).

Flash Point 25C when mixed. Impact 50 cm forward - 50 cm backward. Scratch Pass Flexibility 7.5 - 10 mm.

APPLICATION DATA Application Methods Airless Spray Air Spray Thinning (Max Vol.) 204 (25%) 204 (25%) Thinning / Cleaning of Tools National Thinner 204. Mixing Ratio Base: 4.0 parts by volume.

Curing Agent (hardener): 1.0 part by volume. Pot Life 6 - 8 hrs (20C). Film Thickness (D.F.T.) 80 microns 3.2 mils.

(W.F.T.) 40 microns 1.6 mils. Guiding Data for Airless Spray Nozzle Tip: 0.016 - " 0.019"

Nozzle Pressure: 2000 P.S.I.

SURFACE PREPARATION The surface should be clean and dry at the time of application and its temperature must be above the dew point to avoid condensation.

DRYING TIME For optimum Drying / Curing, good ventilation is always a recommendation. In oven: full curing needs 30 min @ 60C.

1/2

CRYL NCR PRIMER

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

SHELF LIFE 18 months @ (20C) SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtai ned under controlled conditions. We reserve the right to change data without prior notice. 2/2

CRYL NCR PAINT DESCRIPTION National Cryl NCR Paint is a two pack (Polyurethane), glossy topcoat

that has excellent color retention and specially very good resistance against U.V rays.

RECOMMENDED USE As a finishing coat for protection of steel in severely corrosive environment where gloss and color retention is required.

TECHNICAL INFORMATION Colors As per shade card. Finish Glossy (93 - 96 @ 60). Viscosity (20C) 90 - 180 seconds. Specific Gravity 1.12 0.20 (of mix) (for white and Pastel Shades). Solid by Weight % 45% - 65% Theoretical Spreading Rate 9 - 10 m/Lit. @ 40 microns (D.F.T.). Drying time Touch dry : 1 - 2 hrs.

Recoatable: Min: 10 hrs. (20C). Max: 48 hrs. (20C).

Flash Point 26C when mixed. Impact 50 cm forward / 50 cm backward. Scratch Pass. Flexibility 7.5 - 10 mm.

APPLICATION DATA Application Methods Airless Spray Air Spray Thinning (Max Vol.) 204 (25%) 204 (25%) Thinning / Cleaning of Tools National Thinner 204. Mixing Ratio Base: 2.0 parts by volume.

Curing Agent (hardener): 1.0 part by volume. Pot Life 6 - 8 hrs (20C). Film Thickness (D.F.T.) 75 microns 3.0 mils.

(W.F.T.) 40 microns 1.6 mils. Guiding Data for Airless Spray Nozzle Tip: 0.016 - " 0.019"

Nozzle Pressure: 2000 P.S.I.

SURFACE PREPARATION The surface should be clean and dry at the time of application and its temperature must be above the dew point to avoid condensation.

1/2

CRYL NCR PAINT

DRYING TIME For optimum Drying / Curing, good ventilation is always a recommendation. In oven: full curing needs 30 min. @ 60C. Without oven: see the table.

STEEL TEMP DRY TO TOUCH IN HOURS FULLY CURED

RECOATING INTERVALMINIMUM MAXIMUM

20C 3 hrs 7 days 10 hrs 48 hrs 30C 2 hrs 6 days 8 hrs 48 hrs 40C 1 hr 5 days 6 hrs 48 hrs

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

SHELF LIFE 24 months @ 20C. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtai ned under controlled conditions. We reserve the right to change data without prior notice. 2/2

ACRYLIC THINNER

DESCRIPTION Special formulated thinner for acrylic polyurethane coatings application. It contains organic volatile solvents.

RECOMMENDED USE For car refinish coating application at required existing temperature.

TECHNICAL INFORMATION Colors Transparent

Viscosity (20C) 15 - 20 sec.

Specific Gravity 0.97 - 0.87

Evaporation Rate 5 - 15 min.

Flash Point 25 - 54C

APPLICATION DATA Mixing Ratio by Volume 20 - 50%

Fast Thinner 202

Slow Thinner 204

Extra Slow 206

For spot and repairs - or for complete re-sprays provided the temperature in the spray booth does not exceed 20 C

For treatment of large vehicles within the temperature range of

20 - 30 C

For treatment of large vehicles within the temperature range of

30 - 40 C

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations.

The product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

SAFETY / HEALTH - Ensure good ventilation during application and drying. - Avoid contact with skin and eyes. While painting it is advisable

to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtai ned under controlled conditions. We reserve the right to change data without prior notice.

(B-3) NUMIX SYSTEM

NUMIX CLEANER NUMIX PU PRIMER 2K NUMIX PRIMER 1K NUMIX ADHESION PROMOTER NUMIX HARDENER PRIMER NUMIX TOP COAT 2K NUMIX BASE COAT 1K NUMIX CLEAR COAT 2K NUMIX HARDENER NUMIX THINNER NUMIX RETARDANT THINNER NUMIX ANTI SILICON NUMIX SPOT REPAIR THINNER NUMIX PLASTICIZER NUMIX MA-4 MATTING PASTE

NUMIX CLEANER

DESCRIPTION Numix Cleaner is solvent specially selected to remove grease and other contaminants from bare metal, existing finishes, primer surfacer and plastic substrate.

RECOMMENDED USE Bare metal, existing finishes, primer surfacer and plastic.

TECHNICAL INFORMATION Colors Transparent Specific Gravity 0.80

APPLICATION DATA Numix Cleaner is a very good general purpose cleaner, it is suitable for cleaning and degreasing bare metals, existing finishes primer surfacer, etc. Application Technique:

Unsanded existing finishes: 1- Wash the vehicles with detergent and warm water to remove water soluble contaminants. 2- Wash down repaired area with Numix Cleaner to remove any other contaminants. 3- With clean towel dry off the cleaner before evaporation to ensure contaminants removal.

Sanded existing finishes: Apply step 1 & 2 more than once a time after sanding and prior to topcoating.

Untreated plastic substrates: Apply steps 1 - 3 in the same manner, when cleaning unpainted plastic parts allow drying out for 20 - 30 minutes after application of cleaner and prior to primer application.

Bare metal, steel, zinc coated steel and aluminum substrates must be degreased as follows: 1. Wash down the metal with the cleaner. 2. With clean towel dry off the cleaner before evaporation taking into consideration to use one

fresh towel for washing down and another one for wiping dry and replacing towels regularly.

Precaution: Never allow for the cleaned vehicles to be touched with bare hands, moisture and oils which may cause adhesion or blistering problems.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 24 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

NUMIX PU PRIMER 2K DESCRIPTION Numix Polyurethane Primer is a two-component primer filler based on

acrylic resin and polyisocyanate hardener, this product has quickdrying, high filling and good sanding properties. It is a substrate for all type of car refinish.

RECOMMENDED USE As a primer surfacer coat for protection of steel in severely corrosive environment and where gloss and color retention is required.

TECHNICAL INFORMATION Colors Light Grey Finish Flat Viscosity (25C) 15 30 Poise Specific Gravity 1.48 0.02 (of mix). Solid by Weight % 68 70 % Theoretical Spreading Rate 6 - 8 m/Lit. @ 50 microns (D.F.T.) Drying time Touch dry: 1 - 2 hrs.

Recoatable: Min: 3 hrs. (20C). Max: 6 hrs. (20C).

Flash Point 25 C when mixed Impact resistance (25 cm) 50 cm forward / 50 cm backward. Scratch resistance Pass Bending test ( 15 mm) 7.5 10 mm. Water resistance (24 hrs) spot test

Pass

APPLICATION DATA Application Methods Airless Spray and Air Spray Thinning / Cleaning of Tools Numix Thinner. Mixing Ratio by Volume Base: 4 parts.

Curing Agent (hardener): 1 part. Primer 2K-PUNumix Numix Hardener Primer Numix Thinner

100 25 20 Pot Life 2 4 hrs (20C). Film Thickness (D.F.T.) 40 microns 1.6 mils.

(W.F.T.) 75 microns 3.0 mils. Guiding Data for Airless Spray Nozzle Tip: 0.016 - " 0.019"

Nozzle Pressure: 2000 P.S.I.

SURFACE PREPARATION The surface should be clean and dry at the time of application and its temperature must be above the dew point to avoid condensation.

DRYING TIME For optimum Drying/Curing, good ventilation is always a recommendation. In oven: full curing needs 30 min. @ 60C. Without oven: see the table (Hardener Data Sheet).

1/2

NUMIX PU PRIMER 2K

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

SAFETY / HEALTH - Ensure good ventilation during application and drying. - Avoid contact with skin and eyes. While painting it is advisable to

wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtai ned under controlled conditions. We reserve the right to change data without prior notice. 2/2

NUMIX PRIMER 1K DESCRIPTION Numix Primer 1K is single component primer filler based on a

combination of acrylic resin and nitrocellulose, this product is fast drying with high filling and good sanding properties. It is a suitable for all type of car refinish.

RECOMMENDED USE As a primer surfacer coat for protection of steel in severely corrosive environment and where gloss and color retention is required.

TECHNICAL INFORMATION Colors Grey, Greenish Yellow. Finish Flat Viscosity (25C) 20 25 Poise Specific Gravity 1.37 0.02 (of mix) Solid by Weight % 60 - 65 % Theoretical Spreading Rate 6 - 8 m/Ltr. @ 50 microns (D.F.T.) Drying time Touch dry: 1 - 2 hrs.

Recoatable: Min: 3 hrs. (20C). Max: 6 hrs. (20C).

Flash Point 25 C when mixed Impact resistance (25 cm) 50 cm forward / 50 cm backward. Scratch resistance Pass Bending test ( 15 mm) 7.5 10 mm. Water resistance (24 hrs) spot test

Pass

APPLICATION DATA Application Methods Airless Spray and Air Spray Thinning / Cleaning of Tools Numix Thinner. Mixing Ratio by Volume Primer 1KNumix

100 Numix Thinner

20

Film Thickness (D.F.T.) 40 microns 1.6 mils. (W.F.T.) 75 microns 3.0 mils.

Guiding Data for Airless Spray Nozzle Tip: 0.016 - " 0.019" Nozzle Pressure: 2000 P.S.I.

SURFACE PREPARATION The surface should be clean and dry at the time of application and its temperature must be above the dew point to avoid condensation.

DRYING TIME For optimum Drying/Curing, good ventilation is always a recommendation.

1/2

NUMIX PRIMER 1K

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

SAFETY / HEALTH - Ensure good ventilation during application and drying. - Avoid contact with skin and eyes. While painting it is advisable to

wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtai ned under controlled conditions. We reserve the right to change data without prior notice. 2/2

NUMIX ADHESION PROMOTER DESCRIPTION It is special materials developed to conventional coating to adhere well

to untreated polyethylene, polypropylene, or polypropylene / elastomer blends such as TPOs.

RECOMMENDED USE Plastic Surfaces as a Primer.

TECHNICAL INFORMATION Colors Yellowish Viscosity (20C) 1 - 2 Poise Specific Gravity 0.90 0.02 Solid by Weight% (110C) 10 0. 5 % Covering Capacity 4 6 m2/Ltr. Drying time Touch dry: 3 min.

APPLICATION DATA Method of application Air Spray Thinning / Cleaning of Tools Ready to use.

SURFACE PREPARATION Should be dry, clean and free from all loose particles.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 6 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtai ned under controlled conditions. We reserve the right to change data without prior notice.

NUMIX HARDENER PRIMER DESCRIPTION Numix hardener Primer is a polyisocyanate hardener used for curing

Numix PU Primer 2K to insure fast dry and high degree of hardness.

RECOMMENDED USE As a hardener for Numix PU- Primer 2K.

TECHNICAL INFORMATION Colors Transparent Specific Gravity 0.99 Solid by Weight % Approx. 24 Flash Point Approx 20C.

APPLICATION DATA Mixing Ratio by Volume Numix PU-Primer 2K Numix Hardener Primer Numix Thinner

100 25 20 Pot Life 2 hrs Film Thickness 35 microns 1.4 mils. Guiding Data for Airless Spray Nozzle Tip: 0.016 - " 0.019"

Nozzle Pressure: 2000 P.S.I.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 12 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

NUMIX TOP COAT 2K DESCRIPTION Numix Top Coat 2K is two components system based on hydroxyl

functional acrylic resin, includes 35 basic colors and used as a finishing coat in car refinish system.

RECOMMENDED USE Used as a top coat to obtain glossy finish for cars.

TECHNICAL INFORMATION Colors As per shade card. Gloss 96 98% Viscosity (20C) Approx. 8.75 Poise. Specific Gravity Variable and dependable on the color. Solid by Weight % Dependable on the color. Theoretical Spreading Rate 6 - 8 M2/Lit. Drying time 20 hrs @ 20C

30 45 min. @ 60C Flash Point Approx 22C

SURFACE PREPARATION Surface should be well prepared to obtain excellent smooth surface. At the time of application it should be clean and dry.

APPLICATION DATA Application Methods Air Spray (H.V.L.P) Thinning Numix Thinner Mixing Ratio by Volume Numix Top Coat Numix Hardener Numix Thinner

100 50 30 Pot Life 2 - 4 hrs. Film Thickness 35 microns 1.4 mils. Guiding Data for Airless Spray Nozzle Tip: 0.016 - " 0.019"

Nozzle Pressure: 2000 P.S.I.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 24 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

NUMIX BASE COAT 1K DESCRIPTION Numix Base Coat 1K is a one component system based on acrylic resin

and consists of 67 basic colors and used as a basic coat for the finishing layer National Clear Coat.

RECOMMENDED USE As a base coat for car refinish system.

TECHNICAL INFORMATION Colors As per shade card. Gloss Matt. Viscosity (20C) 7 - 8.75 Poise. Specific Gravity Dependable on the color. Solid by Weight % Variable and dependable on the color. Theoretical Spreading Rate 6 8 m2/Lit. (depending on the color). Drying time 10 - 15 min. Flash Point Approx. 22C.

SURFACE PREPARATION Surface should be well prepared to obtain excellent smooth surface. At the time of application it should be clean and dry.

APPLICATION DATA Application Methods Air Spray (H.V.L.P) Thinning Numix Thinner. Mixing Ratio by Volume 100 : 100 Pot Life Unlimited. Film Thickness 35 microns 1.4 mils. Guiding Data for Airless Spray Nozzle Tip: 0.016 - " 0.019"

Nozzle Pressure: 2000 P.S.I.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 24 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

NUMIX CLEAR COAT 2K DESCRIPTION Numix Clear Coat is a two-component top coat with excellent gloss and

color retention. Product noted for very good resistance against U.V. ray. RECOMMENDED USE As a finishing coat for car refinish for protection of structural steel in

severely corrosive environment and where gloss and color retention is required.

TECHNICAL INFORMATION Colors Clear Finish Glossy (96 98 @ 60). Viscosity (20C) 8 - 10 Poise. Specific Gravity 1.02 0.05 (of mix). Solid by Weight % 50 1 % Theoretical Spreading Rate 14.0 m/Ltr. @ 40 microns (D.F.T.). Drying time Touch dry : 30 40 min. @ 60C.

Hard dry : 12 hrs. (20C). Recoatable: 18 hrs. (20C).

Flash Point 25 C when mixed Impact 50 cm forward / 50 cm backward Scratch Pass Flexibility 7.5 10 mm.

APPLICATION DATA Application Methods Airless Spray Air Spray Thinning (Max Vol.) 206 Extra Slow (0.30 part by

volume) 204 Slow (0.30 part by volume) 202 Fast (0.30 part by volume)

206 Extra Slow (0.30 part by volume)

204 Slow (0.30 part by volume) 202 Fast (0.30 part by volume)

Thinning / Cleaning of Tools Numix Thinner 202. Mixing Ratio Base: 2.0 parts by volume.

Curing Agent (hardener): 1.0 part by volume. Pot Life 4 - 6 hrs (20C). Film Thickness (D.F.T.) 33.5 microns 1.34 mils.

(W.F.T.) 70 microns 2.8 mils. Guiding Data for Airless Spray Nozzle Tip: 0.016 - " 0.019"

Nozzle Pressure: 2000 P.S.I.

SURFACE PREPARATION The surface should be clean and dry at the time of application and its temperature must be above the dew point to avoid condensation.

1/2

NUMIX CLEAR COAT 2K

DRYING TIME For optimum Drying / Curing, good ventilation is always a recommendation. In oven: full curing needs 30 min. @ 60C. Without oven: see the table.

STEEL TEMP DRY TO TOUCH IN HOURS FULLY CURED

RECOATING INTERVALMINIMUM MAXIMUM

20C 6 hrs 7 days 12 hrs 48 hrs 30C 5 hrs 6 days 10 hrs 48 hrs 40C 3 hrs 5 days 8 hrs 48 hrs

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

Shelf Life 24 months @ 20C. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtai ned under controlled conditions. We reserve the right to change data without prior notice. 2/2

NUMIX - HARDENER

DESCRIPTION Diluted aliphatic polyisocyanate hardener for polyurethane acrylic paint.

RECOMMENDED USE Polyurethane acrylic coating application - depends on prevailing temperature.

TECHNICAL INFORMATION Colors Transparent Viscosity (20C) ford cup 4 15 sec Specific Gravity 0.96 Solid by Weight% 37 2

APPLICATION DATA Mixing Ratio 50%

Drying time Fast hardener L20 Standard Hardener

S20-30 Slow hardener

M30 20C

Dust Free 25 min. 45 min. 45 min. Tack free 3 hrs. 3.5 hrs. 4 hrs. Dry To Handle 6 hrs. 10 hrs. 12 hrs. Hard Dry 9 hrs. 16 hrs. 18 hrs.

60C Dust Free 5 min. 5 min. 5 min. Tack free 15 min. 15 min. 15 min. Dry To Handle 20 min. 40 min. 50 min. Hard Dry 25 min. 45 min. 50 min. Pot life 25C 2 hrs. 6 hrs. 8 hrs.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

SAFETY / HEALTH - Ensure good ventilation during application and drying. - Avoid contact with skin and eyes. While painting it is advisable to

wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children.

NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience obtai ned under controlled conditions. We reserve the right to change data without prior notice.

NUMIX THINNER

DESCRIPTION Special formulated thinner for acrylic polyurethane coatings application. It contains organic volatile solvents.

RECOMMENDED USE For car refinish coating application at prevailing temperature.

TECHNICAL INFORMATION Colors Transparent

Viscosity (20C) 15 - 20 sec.

Specific Gravity 0.97 - 0.87

Evaporation Rate 5 - 15 min.

Flash Point 25 - 54C

APPLICATION DATA Mixing Ratio by Volume 20 - 50%

Fast Thinner 202

Slow Thinner 204

Extra Slow 206

For spot and repairs - or for complete re-sprays provided the temperature in the spray booth

does not exceed 20C

For treatment of large vehicles within the temperature range of 20 - 30C

For treatment of large vehicles within the temperature range of

30 - 40C

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

SAFETY / HEALTH - Ensure good ventilation during application and drying. - Avoid contact with skin and eyes. While painting it is advisable to

wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtai ned under controlled conditions. We reserve the right to change data without prior notice.

NUMIX RETARDANT THINNER DESCRIPTION Slow thinner of special composition which can be used in conjunction

with various thinners or pure at high temperatures and/or when large vehicles are to be painted, to keep 1K/2K product film longer open to give better overspray met-in and better flow, certainly at high temperature. It will not affect the gloss level.

RECOMMENDED USE At high temperatures (above 25C) and when large vehicles are to be painted.

TECHNICAL INFORMATION Colors Transparent Flash Point 94C

APPLICATION DATA Mixing Ratio by Volume: At high temperatures (above 25C) and when large vehicles are to be painted, it is recommended to add 10 -30 % by volume of Numix Retardant Thinner to the thinner specified for the product concerned at higher temperatures (204 Thinner Slow or 206 Extra Slow, for example). Next add this mix to the product, using the mixing ratio specified in its technical data sheet. This will have a positive effect on its spray and flow characteristics and overspray will be avoided. At temperatures above 40C, Numix Retardant Thinner can also be used pure. In this case, add Numix Retardant Thinner to the product as specified in its technical data sheet, using it as a substitute for the thinner originally recommended. Thinning None the product comes ready to use.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 24 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

NUMIX ANTI SILICON DESCRIPTION Specially selected additive to improve the leveling and remove paint

film defects such as fish eye or craters.

RECOMMENDED USE Leveling improvement of car refinish coating by adding 2% to the paint.

TECHNICAL INFORMATION Colors Transparent Specific Gravity 0.96 Flash Point 27C

APPLICATION DATA Mixing Ratio by Volume 5 - 10 gram for liter of paint at spraying viscosity. Mix well before

spray.

SURFACE PREPARATION Surface should be well prepared to obtain excellent smooth surface. At the time of application it should be clean and dry.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 24 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

NUMIX SPOT REPAIR THINNER DESCRIPTION Numix Spot Repair Thinner is a clear transparent blending additive

thinner that contains acrylic resin and special blend of solvent to allow easier application of Numix Base Coat Spot Repair. It is ready to use where it can be used as foundation for fade out area or used as additive with basecoat colors, solids or metallic, before application of fade out area. Can be applicable over Numix Top Coat 2K and Numix Clear Coat 2K.

RECOMMENDED USE As a clear foundation coat for fade out areas.

APPLICATION DATA

Application Methods: The application method and mixing ratio are depending on the specific use of the product, where the user can select the appropriate method as follows:

1- As a clear foundation to improve the blending of base coat in the spot repair area. Apply 1 single coat of Numix Spot Repair Thinner over the blending area where high gloss and shining coat must be obtained, allow 3 - 5 minutes flash off @ (20C) before spot area with Numix Base Coat 1K taking into consideration that base coat must stay within the coated area spot repair thinner. Note: clear coat must be applied over the spot repair area.

2- Numix Spot Repair Thinner as additive to base coat before blending and fading out. Mix: 100 parts by volume base coat.

50 parts by volume Numix Thinner fast or slow. Apply the mixture until full coverage over the primer area; allow 2 - 3 minutes flash-off time between coats. Then mix base coat color 100 parts, with 100 parts by volume of Numix Spot Repair Thinner, spray 1 - 2 single coats extending beyond the spot repair area with gradual fading out. Allow 15 - 20 minutes @ 20C finally apply a Numix Clear Coat.

Thinning None, the product comes ready to use.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 12 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

NUMIX PLASTICIZER DESCRIPTION Numix Plasticizer is designed to increase flexibility, impact resistance,

chip resistance, and U.V. protection in Numix Top Coat 2K products, it mixes easily and does not affect dry or cure times.

RECOMMENDED USE To improve the flexibility of Numix Top Coat 2K and Numix Clear Coat 2K and over a wide variety of semi-rigid and flexible plastic parts.

TECHNICAL INFORMATION Colors Slightly Yellowish. Flash Point 27C

APPLICATION DATA Application Methods To be added to Numix Top Coat 2K and Numix Clear Coat 2K.Mixing Ratio by Volume 5 - 10% for a liter of paint to be added at spraying viscosity, mix well

after addition. Pot Life 4 - 6 hrs.

SURFACE PREPARATION Surface should be well prepared to obtain excellent smooth surface. At the time of application it should be clean and dry.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 12 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice.

NUMIX MA - 4 MATTING PASTE DESCRIPTION Numix MA-4 Matting Paste standard matting paste designed specially

to matt and reduces the gloss level old Numix Top Coat 2K.

RECOMMENDED USE Over plastic substrates or any other areas that require low gloss.

TECHNICAL INFORMATION Colors Transparent Viscosity (20C) 45 Poise Specific Gravity 1.40 2 Solid by Weight % 55 2 Flash Point Approx 22C.

APPLICATION DATA Application Methods Numix MA-4 Matting Paste can be used with any ratio according to the

desired level of gloss, the table below explains the mixing ratio with Numix Top Coat 2K:

Gloss Level Parts Numix Top Coat 2K

Parts Numix MA-4 Matting Paste

Eggshell (40 - 60) 100 50 Matt (10 - 20) 100 100

Thinning Numix Thinner. Mixing Ratio by Volume After mixing Numix Top Coat 2K with Numix MA-4 Matting Paste

stir the mixture thoroughly, then continue by adding the hardener and the thinner of your choice as per the following ratio:

Numix Top Coat 2K &

Numix MA-4 Matting Paste Numix

Hardener Numix

Thinner

100 50 30 Film Thickness 35 microns 1.4 mils. Guiding Data for Airless Spray Nozzle Tip: 0.016" - 0.019"

Nozzle Pressure: 2000 P.S.I

SURFACE PREPARATION Surface should be well prepared to obtain excellent smooth surface. At the time of application it should be clean and dry.

1/2

NUMIX MA - 4 MATTING PASTE

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 12 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtained under controlled conditions. We reserve the right to change data without prior notice. 2/2

(B-4) MISCELLANEOUS FAST CUT POLISH SOFT POLISH GRAVEL GUARD (GOMA)

FAST CUT POLISH DESCRIPTION A special water base formulation based on resins and coarse silica which

cleans the surface, removes imperfections in the finish and polishes it to give a very smooth surface.

RECOMMENDED USE Use before National Soft Polish for automotive finishes (National N.C. and Acrylic Polyurethane).

TECHNICAL INFORMATION Colors Orange Viscosity (25C) Paste like Specific Gravity 1.39 0.05 Solid By Weight% (110C) 54 5% PH 9.5 1 Silica Contants (

SOFT POLISH DESCRIPTION A special water base formulation based on resins and coarse silica which

gives high gloss polish to the smooth surface and also cleans by removing the dirts.

RECOMMENDED USE Use before National Fast Cut Polish for automotive finishes (National N.C. and Acrylic Polyurethane).

TECHNICAL INFORMATION Colors White. Viscosity (25C) 70 - 80 Poise. Specific Gravity 1.2 0.02 Solid By Weight% 42 2 % PH 9.5 0.5

APPLICATION DATA Thinning / Cleaning of Tools By cotton or special tool. Put polish on surface and apply several times

by equal pressure on the surface with by smooth cloth or cotton. Cleaning of Tools Water.

SURFACE PREPARATION Should be dry, clean and free from all loose particles.

CONDITIONS DURING APPLICATION The temperature of the substrate should be minimum 10C above the dew point and relative humidity measured in the substrate vicinity.

NOTE: Polishing should be carried out after complete drying of paint and according to paint system.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 12 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtai ned under controlled conditions. We reserve the right to change data without prior notice.

GRAVEL GUARD (GOMA)

DESCRIPTION A special resin blend base undercoat which gives a tough textured undercoat to the refinishing that gives extra protection against stone and gravel chipping. Has good color retention, high resistance to severe weather conditions, good durability and flexibility.

RECOMMENDED USE For refinishing plastisol area on cars as replacement coating.

TECHNICAL INFORMATION Color White, Black. Finish Matt textured. Viscosity (25C) 8 - 12 Poise. Specific Gravity 1.45 0.07 Solid by Weight % 70 5% Theoretical Spreading Rate 5 - 12 m2/Lit. Drying time Touch dry: 5 - 10 min.

Hard dry : 8 hrs. Impact resistance (25 cm) pass Scratch resistance pass Bending test ( 15 mm) pass Water resistance (24 hrs) spot test

pass

APPLICATION DATA Application Methods Special Spray Gun. Thinning / Cleaning of Tools Ready for use, could be diluted with Synthetic Thinner Film Thickness (D.F.T.) 70 microns. Guiding Data for Airless Spray Nozzle Tip: 0.015" - 0.20"

Nozzle Pressure: 2200 P.S.I.

SURFACE PREPARATION Surface must be clean, dry and free from oil grease, dirt etc.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 12 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children. NOTE: We warranty the quality of our product and this data sheet represents test results and practical experience

obtai ned under controlled conditions. We reserve the right to change data without prior notice.

(C) FURNITURE & WOOD FINISH PAINTS

(C-1) NITROCELLULOSE PAINTS FLEX CLEAR COAT LACQUER TOP CLEAR COAT LACQUER FLEX SANDING SEALER TOP SANDING SEALER N.C WOOD STAIN N.C THINNER

(C-2) ACRYLIC POLYURETHANE

POLYURETHANE SANDING SEALER POLYURETHANE CLEAR COAT ACID CURING

(C-1) NITROCELLULOSE PAINTS FLEX CLEAR COAT LACQUER TOP CLEAR COAT LACQUER FLEX SANDING SEALER TOP SANDING SEALER N.C WOOD STAIN N.C THINNER

FLEX CLEAR COAT LACQUER

DESCRIPTION It is a fast drying special clear finish based on combination of Nitrocellulose and Alkyd Resins. It has good flexibility and water resistance.

RECOMMENDED USE On wooden furniture, kitchen cabinets and as clear finish on automobiles. It can also be used with wood stains.

TECHNICAL INFORMATION Colors Clear Finish Matt or Glossy (85 - 92 @ 60). Viscosity (25C) 45 - 50 Poise (if dilute with thinner 1:1 for application) 15 - 25 sec. (ford

cup). Specific Gravity 0.96 0.02 Solid by Weight % 40 2 % Theoretical Spreading Rate 6 - 7 m/Lit. @ 25 microns (D.F.T.). Drying time Touch dry: 20 min.

Recoatable: Min 1 hr. Max 3 hrs. @ 20C. Hard dry: 6 hrs. (depending upon thickness).

Flash Point 7C when mixed.

APPLICATION DATA Application Methods Airless Spray Air Spray Thinning (Max Vol.) (50%) (50%) Thinning / Cleaning of Tools National Thinner 121 or National Special Thinner. Mixing Ratio Single pack dilution (1:1). Film Thickness (D.F.T.) 25 microns 1.0 ml.

(W.F.T.) 70 microns / 2.8 ml. Guiding Data for Airless Spray Nozzle Tip: 0.016 - " 0.019"

Nozzle Pressure: 2000 P.S.I. SURFACE PREPARATION

The surface should be clean and dry at the time of application and its temperature must be above the dew point to avoid condensation.

MISCELLANEOUS DATA STORAGE The product must be stored according to National Regulations. The

product should be kept in cool and well ventilated place, protected from heat and direct sunlight at temp 5-35C. Containers must be kept tightly closed.

HANDLING Handle with care, mix well before use. SHELF LIFE 24 months. SAFETY / HEALTH - Ensure good ventilation during application and drying.

- Avoid contact with skin and eyes. While painting it is advisable to wear eye protector. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. To remove splashes from skin; use soap and water or a recognized skin cleaner.

- Keep out of reach of children.

NOTE: We warranty the quality of our product and this data sheet represents test results a