CANOPY HOOD ACCESSORIES
CANOPY HOODACCESSORIES
1890 SwarthmoreAvenue, PO Box 2020 Lakewood, NJ 08701tel.800-526-3694, 732-363-4700, fax.732-364-8110
www.chgusa.com
DESCRIPTION PAGE
A
ACCESS DOORS . . . . . . . . . . . . . . . . . . . . . . . . . . D14,D15AIR FLOw ChARACtERIStICS . . . . . . . . . . . . . . . . D6,D9
CCAp StRIp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D10
DDAMpERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D14DIVIDER BAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D10DRAIN, CANOpy hOOD . . . . . . . . . . . . . . . . . . . . . . . .D11DUCt tApE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D16
FFILtERS
AIR typE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D10BAFFLE typE . . . . . . . . . . . . . . . . . . . . . .D1 thru D8GREASE typE . . . . . . . . . . . . . . . . . . . .D1 thru D10MESh typE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D10StAINLESS StEEL . . . . . . . . . . . . . . . . . .D1 thru D9
FOIL tApE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D16
G
GREASE CUpS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D11GREASE FILtERS . . . . . . . . . . . . . . . . . . . . . . .D1 thru D10GRILLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D14
HhOOD DRAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D11
IINSULAtION hANGERS . . . . . . . . . . . . . . . . . . . . . . . .D16INSULAtION wELD pINS . . . . . . . . . . . . . . . . . . . . . . . .D16
All photographs and illustrations are considered to be a representation of the actual item. In some cases there may be slight variations. this catalog, copy, part numbers and unique method of illustrating products is copyright Component hardware Group. All rights reserved.No portion of this catalog may be reproduced in any form or by any means in whole or in part, without the written consent of Component
hardware Group, Inc. Component hardware Group, Inc. reserves the right to make any and all changes and to discontinue any of its products without notice. Not responsible for typographical errors.
DESCRIPTION PAGE
LLIGhtING FIXtURES
CANOpy hOOD . . . . . . . . . . . . . . . . . . . . .D12, D13E-Z MOUNt CANOpy hOOD . . . . . . . . . . . . . . .D12RECESSED INCANDESCENt . . . . . . . . . . . . . .D13RECESSED FLUORESCENt . . . . . . . . . . . . . . .D13REpLACEMENt pARtS, L55 . . . . . . . . . . . . . . .D12
RREGIStERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D14
SSEALANt, SILICONE . . . . . . . . . . . . . . . . . . . . . . . . . . .D16
TtApE, FOIL & DUCt . . . . . . . . . . . . . . . . . . . . . . . . . . . .D16
WwELD pINS, INSULAtION . . . . . . . . . . . . . . . . . . . . . . .D16
wELD StUDS, KEyhOLE . . . . . . . . . . . . . . . . . . . . . . .D11
wIRE GUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D12
ALPHABETICAL INDEX
NUMERICAL INDEX ON BACK COVER
© COpyRIGht 2009, COMpONENt hARDwARE GROUp, INC.#CAt-X024 05/09–3M pRINtED IN thE U.S.A.
For more information on Flame Gard products visit our website at www.flamegardusa.com
By CH
www.chgusa.com
MODEL NO.
ACTUAL DIMENSIONSH X W X D
WEIGHT PER FILTER
MCD 116 9-1/2 x 15-1/2 x 1-3/4 7.4 Lbs.
MCD 120 9-1/2 x 19-1/2 x 1-3/4 9.1 Lbs.
MCD 123 11-1/2 x 23-1/2 x 1-3/4 13.0 Lbs.
MCD 126 11-1/2 x 15-1/2 x 1-3/4 8.4 Lbs.
MCD 128 11-1/2 x 17-1/2 x 1-3/4 9.3 Lbs.
MCD 133 13 x 23-1/2 x 1-3/4 13.0 Lbs.
MCD 136 13 x 15-1/2 x 1-3/4 10.0 Lbs.
MCD 139 13 x 19 x 1-3/4 12.0 Lbs.
MODEL NO.
TRADE SIZEH X W
ACTUAL DIM.’S H X W X D
WT. PER FILTER
101016 10 x 16(254mm x 406mm) 9-1/2 x 15-1/2 x 1-3/4 7.4 Lbs.
101020 10 x 20(254mm x 508mm) 9-1/2 x 19-1/2 x 1-3/4 9.1 Lbs.
101216 12 x 16(305mm x 406mm) 11-1/2 x 15-1/2 x 1-3/4 8.4 Lbs.
101218 12 x 18(305mm x 457mm) 11-1/2 x 17-1/2 x 1-3/4 9.3 Lbs.
101220 12 x 20(305mm x 508mm) 11-1/2 x 19-1/2 x 1-3/4 10.1 Lbs.
101224 12 x 24(305mm x 610mm) 11-1/2 x 23-1/2 x 1-3/4 12.75 Lbs.
101616 16 x 16(406mm x 406mm) 15-1/2 x 15-1/2 x 1-3/4 10.0 Lbs.
101620 16 x 20(406mm x 508mm) 15-1/2 x 19-1/2 x 1-3/4 12.65 Lbs.
101625 16 x 25(406mm x 635mm) 15-1/2 x 24-1/2 x 1-3/4 16.0 Lbs.
102010 20 x 10(508mm x 254mm) 19-1/2 x 9-1/2 x 1-3/4 9.4 Lbs.
102016 20 x 16(508mm x 406mm) 19-1/2 x 15-1/2 x 1-3/4 12.65 Lbs.
102020 20 x 20(508mm x 508mm) 19-1/2 x 19-1/2 x 1-3/4 15.0 Lbs.
102025 20 x 25(508mm x 635mm) 19-1/2 x 24-1/2 x 1-3/4 17.9 Lbs.
102516 25 x 16(635mm x 406mm) 24-1/2 x 15-1/2 x 1-3/4 14.55 Lbs.
102520 25 x 20(635mm x 508mm) 24-1/2 x 19-1/2 x 1-3/4 18.2 Lbs.
MODEL NO.
TRADE SIZEH X W
ACTUAL DIM.’SH X W X D
WT. PER FILTER
201016 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-7/8 6.3 Lbs.
201020 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-7/8 6.75 Lbs.
201216 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-7/8 6.2 Lbs.
201220 12 x 20 (305mm x 508mm) 11-1/2 x 19-1/2 x 1-7/8 7.5 Lbs.
201616 16 x 16 (406mm x 406mm) 15-1/2 x 15-1/2 x 1-7/8 7.0 Lbs.
201620 16 x 20 (406mm x 508mm) 15-1/2 x 19-1/2 x 1-7/8 8.9 Lbs.
201625 16 x 25 (406mm x 635mm) 15-1/2 x 24-1/2 x 1-7/8 11.65 Lbs.
202016 20 x 16 (508mm x 406mm) 19-1/2 x 15-1/2 x 1-7/8 9.0 Lbs.
202020 20 x 20 (508mm x 508mm) 19-1/2 x 19-1/2 x 1-7/8 10.9 Lbs.
202025 20 x 25 (508mm x 635mm) 19-1/2 x 24-1/2 x 1-7/8 14.0 Lbs.
202516 25 x 16 (635mm x 406mm) 24-1/2 x 15-1/2 x 1-7/8 11.65 Lbs.
202520 25 x 20 (635mm x 508mm) 24-1/2 x 19-1/2 x 1-7/8 13.25 Lbs.
MODEL NO.
TRADE SIZEH X W
ACTUAL DIM.’SH X W X D
WT. PER FILTER
151016 10 x 16(254mm x 406mm) 9-1/2 x 15-1/2 x 1-3/4 7.4 Lbs.
151020 10 x 20(254mm x 508mm) 9-1/2 x 19-1/2 x 1-3/4 9.1 Lbs.
151216 12 x 16(305mm x 406mm) 11-1/2 x 15-1/2 x 1-3/4 8.4 Lbs.
151218 12 x 18(305mm x 457mm) 11-1/2 x 17-1/2 x 1-3/4 9.3 Lbs.
151220 12 x 20(305mm x 508mm) 11-1/2 x 19-1/2 x 1-3/4 10.1 Lbs.
151224 12 x 24(305mm x 610mm) 11-1/2 x 23-1/2 x 1-3/4 12.75 Lbs.
151616 16 x 16(406mm x 406mm) 15-1/2 x 15-1/2 x 1-3/4 10.0 Lbs.
151620 16 x 20(406mm x 508mm) 15-1/2 x 19-1/2 x 1-3/4 12.65 Lbs.
151625 16 x 25(406mm x 635mm) 15-1/2 x 24-1/2 x 1-3/4 16.0 Lbs.
152010 20 x 10(508mm x 254mm) 19-1/2 x 9-1/2 x 1-3/4 9.4 Lbs.
152016 20 x 16(508mm x 406mm) 19-1/2 x 15-1/2 x 1-3/4 12.65 Lbs.
152020 20 x 20(508mm x 508mm) 19-1/2 x 19-1/2 x 1-3/4 15.0 Lbs.
152025 20 x 25(508mm x 635mm) 19-1/2 x 24-1/2 x 1-3/4 17.9 Lbs.
152516 25 x 16(635mm x 406mm) 24-1/2 x 15-1/2 x 1-3/4 14.55 Lbs.
152520 25 x 20(635mm x 508mm) 24-1/2 x 19-1/2 x 1-3/4 18.2 Lbs.
FLAME GARD–TYPE I & TYPE II
• STANDARD FIXED BAFFLES • SPARK ARRESTOR
TYPE I–STANDARD
FLAME GARD–TYPE II
TYPE II–HEAVY DUTY STAINLESS STEEL
McDONALDS FILTER MODEL/SIZES
TYPE 1 WITH SPARK ARRESTORAVAILABLE. MEETS CRITERIA
SET BY NFPA #96 FOR COOKINGWITH SOLID FUEL
*HOLES FOR HANDLES & BRACKETS INSTALLED WITH FILTER PURCHASE. ALL FILTERS ARE AVAILABLE WITH SPECIAL MARYLAND
LOCKING HANDLES. WHEN ORDERING MARYLAND LOCKING HANDLES, ADD SUFFIX–MH TO PART NUMBER.
TYPE I–w/SPARK ARRESTOR
C US
D1
MODEL NUMBER
TRADE SIZEH X W
ACTUAL DIMENSIONSH X W X D
551016 10 x 16 9-1/2 x 15-1/2 x 1-5/8
551020 10 x 20 9-1/2 x 19-1/2 x 1-5/8
551216 12 x 16 11-1/2 x 15-1/2 x 1-5/8
551220 12 x 20 11-1/2 x 19-1/2 x 1-5/8
551616 16 x 16 15-1/2 x 15-1/2 x 1-5/8
551620 16 x 20 15-1/2 x 19-1/2 x 1-5/8
551625 16 x 25 15-1/2 x 24-1/2 x 1-5/8
551818 18 x 18 17-1/2 x 17-1/2 x 1-5/8
552016 20 x 16 19-1/2 x 15-1/2 x 1-5/8
552020 20 x 20 19-1/2 x 19-1/2 x 1-5/8
552025 20 x 25 19-1/2 x 24-1/2 x 1-5/8
552516 25 x 16 24-1/2 x 15-1/2 x 1-5/8
552520 25 x 20 24-1/2 x 19-1/2 x 1-5/8
MODEL NUMBER
TRADE SIZEH X W
ACTUAL DIMENSIONSH X W X D
451016 10 x 16 9-1/2 x 15-1/2 x 1-5/8
451020 10 x 20 9-1/2 x 19-1/2 x 1-5/8
451216 12 x 16 11-1/2 x 15-1/2 x 1-5/8
451220 12 x 20 11-1/2 x 19-1/2 x 1-5/8
451616 16 x 16 15-1/2 x 15-1/2 x 1-5/8
451620 16 x 20 15-1/2 x 19-1/2 x 1-5/8
451625 16 x 25 15-1/2 x 24-1/2 x 1-5/8
451818 18 x 18 17-1/2 x 17-1/2 x 1-5/8
452016 20 x 16 19-1/2 x 15-1/2 x 1-5/8
452020 20 x 20 19-1/2 x 19-1/2 x 1-5/8
452025 20 x 25 19-1/2 x 24-1/2 x 1-5/8
452516 25 x 16 24-1/2 x 15-1/2 x 1-5/8
452520 25 x 20 24-1/2 x 19-1/2 x 1-5/8
MODEL NUMBER
TRADE SIZEH X W
ACTUAL DIMENSIONSH X W X D
301016 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-5/8
301020 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-5/8
301216 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-5/8
301220 12 x 20 (305mm x 508mm) 11-1/2 x 19-1/2 x 1-5/8
301616 16 x 16 (406mm x 406mm) 15-1/2 x 15-1/2 x 1-5/8
301620 16 x 20 (406mm x 508mm) 15-1/2 x 19-1/2 x 1-5/8
301625 16 x 25 (406mm x 635mm) 15-1/2 x 24-1/2 x 1-5/8
301818 18 x 18 (457mm x 457mm) 17-1/2 x 17-1/2 x 1-5/8
302016 20 x 16 (508mm x 406mm) 19-1/2 x 15-1/2 x 1-5/8
302020 20 x 20 (508mm x 508mm) 19-1/2 x 19-1/2 x 1-5/8
302025 20 x 25 (508mm x 635mm) 19-1/2 x 24-1/2 x 1-5/8
302516 25 x 16 (635mm x 406mm) 24-1/2 x 15-1/2 x 1-5/8
302520 25 x 20 (635mm x 508mm) 24-1/2 x 19-1/2 x 1-5/8
www.chgusa.com
ALUMINUM GALVANIZED
STAINLESS STEEL
REpLACEMENt BALE hANDLES: typE III - MODEL NO. 300001
FLAME GARD–TYPE III
STAINLESS STEEL, ALUMINUM & GALVANIZED FILTERS
C US
D2
Note: Metric dimensions noted above apply to all on this page.
*HOLES FOR HANDLES & BRACKETS INSTALLED WITH FILTER PURCHASE.
ALL FILTERS ARE AVAILABLE WITH SPECIAL MARYLAND LOCKING HANDLES. WHEN ORDERING
MARYLAND LOCKING HANDLES, ADD SUFFIX–MH TO PART NUMBER.
RESULTSthE FOLLOwING DAtA wAS RECORDED ON thE UNItS
tEStED. 20 IN. By 20 IN. StEEL tEFLON COAtED FILtERS
WEIGHT OF GREASE GENERATEDBefore test 95 lb.After test 87.5 lb.Cooking Oil Used 7.5 lb.
weight Before weight After weight of Grease test test On Filter
Filter #1 15 lb. 6 oz. 15 lb. 6 oz. 0 oz.Filter #2 15 lb. 5 oz. 15 lb. 5 oz. 0 oz.
weight of oil collected from the grease filter run off 7 lb. 4 oz. Amountof oil not retained or collected 1 oz. the quantity of grease passingthrough the filter to the exhaust duct did not exceed 6 percent of theamount generated.
800-526-3694
94% EFFICIENT AT GREASE EXTRACTIONAs tested by Underwriters Laboratories of Canada it has been proventhat Flame Gard 1 grease filters have the highest rate of greaseextraction of any filter on the market today while still maintainingextremely low static pressures. quoting U.L.C. File #CR1157 it wasstated that the quantity of grease passing through the filter to the exhaustduct did not exceed 6% of the amount generated. (please refer to theU.L.C. Report contained in the technical section of our full line catalog.)
SIMPLE BUT EFFECTIVE BAFFLE DESIGNFlame Gard’s “U” shaped baffles were arrived at after extensive testing.the smooth, deep baffles cause the grease to drain off the filter quickly,and they resist flame penetration without disturbing the movement of air.Flame Gards have more baffles per inch of filter which is a key factor inour high rate of grease extraction and out low static pressure. Morebaffles mean more grease impingement area and more paths for the airto flow smoothly and quickly through filter. these combined featuresmake Flame Gard I’s the most energy efficient filters available.
TEFLON® COATED BAFFLESFlame Gard’s high rate of grease extraction is aided by our tEFLON®coated baffle. In the same manner that grease rolls off a tEFLON coatedpan, it rolls down our baffles, out of the filter and into the hood’s remotecollection cup. Because Flame Gard’s filters retain only insignificantamounts of surface grease and do not load, you will have constancy ofair flow throughout your operating day. In addition, Flame Gard’s filterscan be easily cleaned in a pot sink or dishwasher with simple detergentand hot water.
Teflon®-Coated Baffles & Spark Arrestor
FLAME GARD– TYPE I
CLASSIFIED BAFFLE GREASE FILTER MEETS NFPA 96
REqUIREMENT FOR COOKING WITH SOLID FUEL
MARYLAND LOCKING HANDLES AVAILABLE
SPARK ARRESTOR FRAME
thE 3/8” X 1/2” SpARK ARREStOR FRAME MEEtS NFpA 211REqUIREMENt FOR SOLID FUEL BURNING AppLIANCES
n ALL STEEL CONSTRUCTIONn ALL SIZES AVAILABLEn NON-LOADING TEFLON COATED BAFFLESn LOW STATIC PRESSURE
NATIONAL FIRE PROTECTION ASSOCIATION NFPA 96, CHAPTER 11-5.1 STATES
If airborne sparks and embers can be generated by the solid fuel cookingoperation, spark arrestor devices shall be used prior to the greaseremoval device to minimize the entrance of these sparks and embers intothe grease removal device and into the hood and duct system.
NFPA 211 CHAPTER 1.11.2 (B) STATES:
(b) the arrestor screen shall have heat and corrosion resistanceequivalent to 19 gauge (0.011 in.) galvanized steel or 24 gauge (0.024in.) stainless steel.(c) Opening shall not permit the passage of spheres having a diameterlarger than 1/2 in. (12.7mm) nor block the passage of spheres having adiameter of less than 3/8 in. (9.5mm).
D3
TWO MODELS AVAILABLE....1. Standard Fixed Baffles2. Spark Arrestor Frame
94% EFFICIENT AT GREASE EXTRACTION!“The quantity of grease passing through the filter to the exhaust duct did
not exceed 6% of the amount generated!”
METHODtwo sample steel filters were weighed and then mounted side by sidein the hood. the damper was adjusted to provide a stack velocity ofapproximately 1800 f.p.m. the distance from the broiler surface to thebottom of the unit was approximately 36 in. the grease generator wasweighed, partially filled with cooking oil, reweighed and the weighedrecorded.
the grease generatory was placed on the electric broiler and heateduntil the temperature of the cooking oil was 400˚ F. the sizing of thespray nozzle was such that grease was discharged at approximatelyone pound per hour per foot width of the test hood.
the test continued for 2 hours...
At the end of the test, the grease laden filters were weighed. the greasecollected from the filter run off was collected and weighed. the greasegenerator was weighed again to determine the weight of grease used.
SELECTION CHARTENGINEERING DATACFM - STATIC PRESSURESTATIC PRESSURE - INCHES OF H20
www.chgusa.com
HOW FLAME GARD® WORKSthe affluent from cooking processes contains aerosols of water vapor mixedwith evaporated fat or oil. these are carried from the cooking surface by themoving air being drawn into the exhaust hood.
Although small, each aerosol is much heavier than the air moleculessurrounding it.
thus, when the air stream containing these aerosols strikes the Flame Gard®
Baffle System, the inertial force of the moisture-grease aerosol is considerablygreater than that of the air molecule. while the air molecule changes directioneasily, the aerosol strikes the baffle with considerable force, causing it to“splatter” on the surface. Because the surface is coated with a teflon®, thegrease slides down to the trough and then to the collecting container.
whereas the heaviest aerosols, because of their greater inertial force, impingeon the surfaces of the baffles facing and perpendicular to the air flow, the lighterones remain in the air stream. As the air stream is drawn through the bafflesystem, the restrictions in area created by the baffles cause the air to increasein velocity while changing direction by 180 degrees. Since the inertial force is aproduct of the mass and the square of the velocity, this increase in velocityserves to increase the inertial force of the remaining smaller aerosols, causingthem to impinge on the inner surfaces of the baffles in the same manner inwhich the heavier aerosols impinged on the entering surfaces. the design of thebaffle system provides several impingement surfaces and two rapid 180-degreedirection changes.
Because Flame Gard® removes grease aerosols from the air stream and drainthem away instead of retaining them. there is no build-up of grease in the pathof the air Flame Gard® therefore, insures a constancy of air never beforeachievable with mesh-type filters.
WARRANTYFlame Gard® I has a one-year warranty against defective material or workmanship.
RECOMMENDED WORDING FOR GREASE FILTER SPECIFICATION
LONG FORMGrease filters shall be as manufactured by Flame Gard®. they shall consist of two offsetting baffle assemblies held in position by metal screws, allcontained in a metal frame with expanded metal trim on the face and back.
Baffle assemblies shall c onsist of “U”-shaped channels of 20-gauge steel,coated by no less than one mil of Dupont teflon® 22. Channels shall beseparated and held in parallel alignment by 14-gauge steel cross members.Baffle assemblies shall be mounted in their frames reserved one to the otherand staggered so that the side of each channel is aligned with, and spacedevenly from, the side of an opposing channel.
Frames shall be constructed of nickel-plated 18-gauge cold-rolled steel with 3/8inch diameter openings for drainage of grease. Frames shall consist of two partspermanently held together by metal screws.
protective trim shall be made of 16-gauge nickel-plated, diamond-shaped,expanded cold-rolled steel.
Stainless steel handles shall be provided on each side of the front frame forease of removal and replacement in exhaust hoods.
SHORT FORMGrease Filters shall be as manufactured by Flame Gard®. Filter shall consist ofan outside rear and front frame of nickel-plated steel welded to a front face ofexpanded steel. with two opposing teflon-coated baffles inside.
STANDARDSthe NAtIONAL EVALUAtION SERVICES COMMItEE of the Council of AmericanBuilding Officials, a co-operative consisting of a consolidation of these formerorganizations: Building Officials and Code Administrators International, Inc.;International Conference of Building Officials; and Southern Building Code CongressInternational, Inc.; and which now provides uniform standards for the entire UnitedStates, recognizes Flame Gard® when installed with the manufacturer’srecommendation and the following table:
TABLE 1 HEIGHT OF GREASE FILTERStype of Cooking Equipment height Above Cooking Surface(ft.)
without Exposed Flame 0.5Exposed Flame 2.0 Charcoal Burning 2.0
A complete list of governmental and industry approvals is available on request. SeeNational Evaluation Service report No. NER-255 for allowable values and or conditionsof use concerning material presented in this document. It is subject to re-examination,revisions, and possible cancellation. NER-255, “Condition of Use” - filters to be usedin a kitchen exhaust system that is protected with an automatic fire supression system.
UNDERwRItERS’ LABORAtORIES, INC., Flame Gard® Grease Filters are classifiedby Underwriters’ Laboratories, Inc., as to flammability after exposure to grease-ladenair only. Guide AKUS, File #R10173 see Underwriters’ Laboratories Classified BuildingMaterials Index.
Accepted for use, CIty OF NEw yORK DEpARtMENt OF BUILDINGS NO.MEA481-7.1-SM.Meets the requirements of NAtIONAL FIRE pROtECtION ASSOCIAtION,Standard No. 96.
SIZES/INSTALLATIONFlame Gard® should always be installed with the baffles in a vertical position, in orderto allow the grease particles to be drawn into the collection system by gravity.
Standard sizes are ordered with the vertical(top to bottom) dimension stated first,followed by the horizontal (left to right)dimension. For information on sizes not listed,contact the factory, your representative, oryour foodservice equipment dealer.
Teflon®-Coated Baffles & Spark Arrestor
FLAME GARD–TYPE I
*Measured 6” behind Flame GardStatic pressure per filter, asincluded in this chart, representsthe total static pressure for thesystem regardless of the numberof filters used in the hood.
TYPE II-STAINLESS STEEL GREASE FILTERS
D4
Size 10x16 10x20 12x20 16x20 16x25 20x20 20x25
350 .350 .185 .160 .075 .045 .045 .030
400 .495 .240 .205 .095 .055 .055 .040
450 .695 .310 .260 .120 .065 .065 .045
500 .390 .325 .145 .080 .080 .055
550 .485 .395 .175 .100 .100 .065
600 .595 .475 .215 .120 .120 .080
650 .720 .570 .255 .150 .150 .090
700 .670 .300 .180 .180 .105
750 .305 .210 .210 .120
800 .400 .250 .230 .140
850 .460 .290 .290 .165
900 .530 .330 .330 .185
950 .600 .380 .380 .210
1000 .670 .430 .430 .240
1050 .480 .480 .275
1100 .540 .540 .320
1150 .610 .610 .365CF
M p
ER
FIL
tE
R -
(7
5
AIR
)
TRADE SIZE ACTUAL DIMENSIONS
H x W H x W x D10 x 16 9-1/2 x 15-1/2 x 1-3/410 x 20 9-1/2 x 19-1/2 x 1-3/412 x 16 11-1/2 x 15-1/2 x 1-3/412 x 20 11-1/2 x 19-1/2 x 1-3/416 x 16 15-1/2 x 15-1/2 x 1-3/416 x 20 15-1/2 x 19-1/2 x 1-3/416 x 25 15-1/2 x 24-1/2 x 1-3/420 x 16 19-1/2 x 15-1/2 x 1-3/420 x 20 19-1/2 x 19-1/2 x 1-3/420 x 25 19-1/2 x 24-1/2 x 1-3/425 x 16 24-1/2 x 15-1/2 x 1-3/425 x 20 24-1/2 x 19-1/2 x 1-3/4
800-526-3694
FLAME GARD–TYPE II
TYPE II-STAINLESS STEEL GREASE FILTERS
STAINLESS STEEL
GREASE FILTERS
DUAL ACTION
GREASE FILTER FEATURES:
ACTION ONE provides positive flame barrier protection.Its stainless steel interlocking baffle walls make it themost effective flame barrier of all filters marketed today.
ACTION TWO provides unsurpassed performancein efficient grease removal. the aerodynamic twin-wall “V” baffles continuously separate grease and air.Stainless steel surfaces assure constant run-off andallow grease to be safely deposited in collection troughs.
FILTERS WITH LOCKING HANDLESARE AVAILABLE tO COMpLy wIth MARyLAND,
VIRGINIA AND wAShINGtON D.C. SpECIFICAtIONS FOR COMMERCIAL hOODS.
tO ORDER StAtE SIZE wIth SUFFIX-Mh
*LOCKING HANDLES ARE ONLY AVAILABLE
UPON APPLICATION
TYPE II-SERIES STAINLESS STEEL FILTERS W/DROP HANDLES (STANDARD)
CHG MODEL #
201016
201020
201216
201220
201616
201620
201625
202016
202020
202025
202516
202520
STANDARD-KEIL #
2610-1016-1251
2610-1020-1251
2610-1216-1251
2610-1220-1251
2610-1616-1251
2610-1620-1251
2610-2020-1251
2610-2520-1251
2610-2020-1251
2610-2025-1251
2610-2516-1251
2610-2520-1251
WGT.(LBS/KG)
5-1/2 (2.49kg)
6 (2.72kg)
6-1/2 (2.95kg)
7 (3.17kg)
8 (3.63kg)
8-1/2 (3.85kg)
10-1/2 (4.76kg)
6-1/2 (2.95kg)
10-1/4 (4.65kg)
12 (5.44kg)
11-1/2 (5.21kg)
12 (5.44kg)
SIZE
10 x 16(254 x 406mm)
10 x 20(254 x 508)
12 x 16(305 x 406mm)
12 x 20(305mm x 508mm)
16 X 16(406mm x 406mm)
16 x 20(406mm x 508mm)
16 x 25(406mm x 635mm)
20 x 16(508mm x 406mm)
20 x 20(508mm x 508mm)
20 x 25(508mm x 635mm)
25 x 16(635mm x 406mm)
25 x 20(635mm x 508mm)
COMpONENt
n SAFESt BAFFLE FILtER AVAILABLE
n pROVIDES pOSItIVE FLAME BARRIER pROtECtION
n hEAVy DUty SOLID StAINLESS StEEL wELDEDCONStRUCtION
n StURDy DROp hANDLES pROVIDED
n pOLIShED VANES pROVIDE SELF- DRAINING GREASE RUN OFF
n hIGhLy EFFICIENt IN GREASE REMOVAL
n pAtENtED VANE DESIGN pREVENtS GREASE FROM DRIppING -FOOD, UtENSILS AND BURNER SURFACESREMAIN CLEAN
n RUGGED, wELDED StAINLESS StEEL CONStRUCtION OFFERS EASy CLEANABILIty, CAN wIthStAND tODAy’S hARSh CLEANING SOLUtIONS, AND FItS IN StANDARD SIZE DIShwAShER
n ECONOMICAL...NEVER NEEDS REpLACING
n RECOMMENDED By LEADING CONSULtANtS AND DESIGNERS
n MEEtS REqUIREMENtS OF NAtIONAL FIRE pROtECtION
ASSOCIAtION BULLEtIN #96
n tEStED AND CLASSIFIED By UNDERwRItERS LABORAtORIES, INC. FILE #R10173
heavy-duty stainless steel grease filters
D5
NOtE: ACtUAL FILtER thICKNESS IS 1-7/8” (47.6mm)
www.chgusa.com
OPERATIONGrease laden air isdrawn into the filter bythe exhaust fans. As the air starts throughthe aerodynamic “V” baffle system, itundergoes a series of compressions, expansions andpressure changes. the heavy grease is depositedsafely and quickly on the baffles while the grease-freeair passes through the filter and up the exhaust duct.the baffle’s smooth surface enables the collectedgrease to run off into collection troughs withoutdripping on food,utensils or burner surfaces.the ChGGrease filter method of separating grease and air hasachieved superior levels for efficiency and safety notattained by competitor’s filters.
CONSTRUCTIONChG stainless steel grease filters are constructed ofheavy duty type 304 stainless steel, providing themost durable filter available in today’s market, andwill provide years of trouble-free operation. thereare no coatings to wear out and no involvedmechanisms which can jam.All stainless steel grease filters are guaranteedagainst defects in workmanship or materials.
MAINTENANCEthe all-stainless steel construction allows the filter to be soaked, sprayed or placed in a dishwasher for simplified cleaning, without concern for rusting orwearing out of surface coatings.
EFFECTIVE AREA CHART
NOMINAL L x W x T
10 x 20 x 2
12 x 20 x 2
16 x 20 x 2
16 x 25 x 2
20 x 20 x 2
20 x 25 x 2
EFFECTIVE AREA Square Feet
1.00
1.25
1.75
2.24
2.25
2.88
STATIC PRESSURE
CFM perFilter
150175200225250275300325350375400425450475500525550575600625650 675700725750775800825850875900925
10 x 20
.12
.18
.25
.31
.38
.46
.55
.63
.72
.84
.951.061.171.321.451.601.751.90
12 x 20
.02
.06
.11
.16
.21
.26
.31
.37
.43
.50
.56
.62
.70
.77
.85
.921.011.101.181.271.371.471.581.701.811.95
16 x 20
.03
.07
.11
.15
.18
.23
.27
.32
.37
.42
.47
.52
.57
.62
.66
.75
.81
.87
.931.011.071.141.221.301.371.461.551.651.751.87
16 x 2520 x 20
.03
.06
.09
.12
.15
.18
.22
.25
.28
.32
.36
.40
.44
.48
.52
.57
.62
.67
.72
.77
.82
.88
.931.001.061.121.171.23
25 x 20
.03
.04
.06
.08
.10
.12
.14
.16
.18
.21
.23
.25
.27
.30
.32
.35
.37
.41
.43
.46
.49
.53
.56
.60
.63
.67
.71
.20 .40 .60 .80 1.00 1.20 1.40 1.60 1.80 2.00
20 x 25
16 x 25
20 x 20
16 x 20
12 x 20
10 x 20
AIR FLOW CHARACTERISTICS
SELF-BALANCINGwith conventional mesh filters, it isnecessary to pull two to five timesas much air through the center filterto get good smoke and greasevapor capture on the ends of ahood. this is a needless waste ofcostly heated or air conditioned air.ChG grease filters areaerodynamically designed toprovide a self-balancing air flowthroughout the entire length of ahood. Actual field tests haverepeatedly shown a variation of less than + 10° air flow from end to end.this unique design assures good capture through theentire hood length, with 25 to 50% less volume ofexhaust air.
‘‘
‘‘ CONVENTIONAL MESH AIR FLOW
SELF-BALANCING AIR FLOW
StAtIC pRESSURE (measured in inches of h20)
CF
M P
ER
FIL
TE
R
ALL CHG STAINLESS STEEL GREASE FILTERS ARE:Classified by Underwriters’ Laboratories Inc.-File #R 10173.
COMPONENT HARDWARE GROUP, INC. Grease filter classification byUnderwriters’ Laboratories, Inc., as to flammability only after exposure togrease-laden air. See U.L. Classified Building Material Index. File #R10173
1400
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
FLAME GARD–TYPE II
heavy-duty stainless steel grease filters
D6
TABLE 1 HEIGHT OF GREASE FILTERStype of Cooking Equipment height Above Cooking Surface(ft.)
without Exposed Flame 0.5Exposed Flame 2.0Charcoal Burning 2.0
A complete list of governmental and industry approvals is available on request.
See National Evaluation Service report No. NER-255 for allowablevalues and or conditions of use concerning material presented in thisdocument. It is subject to re-examination, revisions, and possiblecancellation. NER-255, “Condition of Use” - filters to be used in akitchen exhaust system that is protected with an automatic firesuppressions system.
UNDERwRItERS’ LABORAtORIES, INC., Flame Gard® Grease filtersare classified by Underwriters’ Laboratories, Inc., as to flammabilityafter exposure to grease-laden air only. Guide AKUS, File #R10173,see Underwriters’ Laboratories Classified Building Materials Index.
UNDERwRItERS’ LABORAtORIES OF CANADA Guide No. 440E13;File No. CR1157.
Accepted for use, CIty OF NEw yORK DEpARtMENt OFBUILDINGS NO. MEA481-7.1-SM.
Meets the requirements of NAtIONAL FIRE pROtECtIONASSOCIAtION, Standard No. 96.
SIZES/INSTALLATIONFlame Gard® should always be installed with the baffles in a verticalposition, in order to allow the grease particles to be drawn into thecollection system by gravity.
Standard sizes are ordered with the vertical (top to bottom) dimensionstated first, and the horizontal (left to right) dimension second. Forinformation on sizes not listed, contact the factory, your representative,or your food-service equipment dealer.
800-526-3694
stainless steel, galvanized & aluminum grease filters
TYPE III STAINLESS, ALUMINUM AND GALVANIZED FILTERS STATIC PRESSURE SELECTION CHART
FLAME GARD–TYPE III
HOW FLAME GARD® WORKS
the affluent from cooking processes contains aerosols of water vapormixed with evaporated fat or oil. these are carried from the cookingsurface by the moving air being drawn into the exhaust hood. Althoughsmall, each aerosol is much heavier than the air molecules surroundingit. thus, when the air stream containing these aerosols strikes theFlame Gard® Baffle System, the inertial force of the moisture-greaseaerosol is considerably greater than that of the air molecule. while theair molecule changes direction easily, the aerosol strikes the baffle withconsiderable force, causing it to “splatter” on the surface.
whereas the heaviest aerosols, because of their greater inertial force,impinge on the surfaces of the baffles facing and perpendicular to theair flow, the lighter ones remain in the air stream. As the air stream isdrawn through the baffle system, the restrictions in area created by thebaffles cause the air to increase in velocity while changing direction by180 degrees. Since the inertial force is a product of the mass and thesquare of the velocity, this increase in velocity servesw to increase theinertial force of the remaining smaller aerosols, causing them toimpinge on the inner surfaces of the baffles in the same manner inwhich the heavier aerosols impinged on the entering surfaces. the design of the baffle system provides severalimpingement surfaces and two rapid
180-degree direction changes. the grease slides down to the greasetrough and then to the collection container.
STANDARDSthe National EVALUAtION SERVICES Commitee of the Council ofAmerican Building Officials, a co-operative consisting of a consolidationof these former organizations: Building Officials and CodeAdministrators International, Inc.; International Conference of BuildingOfficials; and Southern Building Code Congress International, Inc.; andwhich now provides uniform standards for the entire United States,recognizes Flame Gard® when installed with the manufacturer’srecommendation and the following table:
10 x 16 10 x 20 16 x 16 16 x 20 16 x 25 20 x 16 20 x 20 20 x 25 25 x 16 25 x 20
200 .34 .19 .12 .07 .05 .09 .04 .03 .05 .03
300 .84 .48 .33 .19 .12 .23 .11 .07 .13 .07
400 1.46 .83 .57 .33 .21 .41 .19 .13 .23 .13
500 2.27 1.28 .86 .50 .32 .61 .29 .195 .355 .195
600 3.27 1.86 1.27 .73 .46 .90 .42 .28 .52 .29
700 4.45 2.53 1.73 .99 .63 1.23 .57 .38 .70 .39
800 5.73 3.32 2.26 1.30 .82 1.59 .74 .49 .92 .505
900 7.38 4.19 2.87 1.64 1.04 2.04 .94 .64 1.17 .65
1000 9.13 5.15 3.47 2.03 1.28 2.49 1.17 .78 1.425 .79
1100 6.24 4.27 2.44 1.55 3.04 1.40 .95 1.74 .97
1200 7.38 5.08 2.92 1.84 3.59 1.67 1.13 2.07 1.15
1300 8.74 5.98 3.42 2.17 4.26 1.97 1.33 2.44 1.35
1400 6.92 3.95 2.52 4.93 2.28 1.54 2.82 1.56
1500 7.95 4.55 2.89 5.66 2.61 1.77 3.24 1.80
ALL tEStS CONDUCtED By CEDRt-AIRE tEChNICAL SERVICES tO AMCA StANDARD 500-89
CFM - Static pressureStatic pressure - Inches of h20
D7
12pCS
12pCS
6pCS
6pCS
12pCS
12pCS
6pCS
6pCS
6pCS
6pCS
6pCS
6pCS
COMPONENT HARDWARE GROUP: GREASE FILTER
CLASSIFIED BY UNDERWRITERS LABORATORIES, INC. ASTO FLAMMABILITY AFTER EXPOSURE TO GREASE LADENAIR ONLY (54-H6). FILE #R10173 (N) ACCEPTED BY THECITY OF NEW YORK-DEPARTMENT OF BUILDINGS-MEA#137-82-E, VOL.2
LBS/CtN
17.6
20.2
12.9
15.6
21.1
24.4
15.6
19.8
23.5
20.2
23.5
MODEL NO.
FA30-1016-hD
FA30-1216-hD
FA30-1616-hD
FA30-2016-hD
FA30-1020-hD
FA30-1220-hD
FA30-1620-hD
FA30-2020-hD
FA30-2520-hD
FA30-1625-hD
FA30-2025-hD
ALUMINUM
12pCS
12pCS
6pCS
6pCS
12pCS
12pCS
6pCS
6pCS
6pCS
6pCS
6pCS
6pCS
LBS/CtN
31.4
35.4
26.1
29.4
40.7
44.6
29.4
35.4
42.6
36.0
36.0
42.6
MODEL NO.
FS50-1016-BA
FS50-1216-BA
FS50-1616-BA
FS50-2016-BA
FS50-1020-BA
FS50-1220-BA
FS50-1620-BA
FS50-2020-BA
FS50-2520-BA
FS50-1625-BA
FS50-2516-BA
FS50-2025-BA
StAINLESS StEELBRIGht FINISh
LBS/CtN
30.1
34.1
25.5
28.8
39.3
43.3
28.8
34.1
41.3
34.7
34.7
41.3
GREASE DEFENDER™
BAFFLE TYPE GREASE FILTERSpAtENt 6840975
STANDARD COMMERCIAL SIZES
STAINLESS STEEL & S/S BRIGHT FINISHFor tough commercial applications and maximum permanent protection against rust and corrosion
ALUMINUMLightweight for ease of handling
GALVANIZED STEELfor strong rugged performance, superb corrosion
resistance and absolute low cost
standard duty grease filters
D8
REPLACEMENT LOCKING HANDLES ARE AVAILABLE
IN PAIRS. SPECIFY...MODEL NO. F40-0002
WHEN ORDERING.
ALL FILTERS ARE SUPPLIED
WITH HANDLES.
FILTERS WITH LOCKING
HANDLES ARE AVAILABLE
TO COMPLY WITH
MARYLAND, VIRGINIA AND
WASHINGTON D.C.
SPECIFICATIONS FOR
COMMERCIAL HOODS.
TO ORDER STATE SIZE
WITH PREFIX...
FA31...FOR ALUMINUM
FG36...FOR GALVANIZED STEEL
FS51...FOR STAINLESS STEEL
n UNIqUE “ROLL LOCK” CAN SEAM DESIGN MAKES GREASE
DEFENDER THE MOST DURABLE FILTER ON THE MARKET
n WILL NOT FLEX OR TWIST LIKE OTHER FILTERS EVEN AFTER REPEATED DROPPING
n SAFE, DEPENDABLE, POSITIVE FLAME BARRIER PROTECTION
n SEAMLESS, SMOOTH SURFACES PERMIT CONSTANT GREASERUN-OFF INTO HOOD COLLECTION TROUGHS...EASILY CLEANED BY SOAKING, SPRAYING OR IN CONVENTIONAL DISHWASHERS
S/S BRIGht FINISh
qty
&
CARtON
qty
&
CARtON
ALUMINUM GALVANIZED StEEL
MODEL NO.
FG35-1016-hD
FG35-1216-hD
FG35-1616-hD
FG35-2016-hD
FG35-1020-hD
FG35-1220-hD
FG35-1620-hD
FG35-2020-hD
FG35-2520-hD
FG35-1625-hD
FG35-2516-hD
FG35-2025-hD
GALVANIZED StEEL
SIZE: INChES (mm)
10 x 16 (250 x 400)
12 x 16 (300 x 400)
16 x 16 (400 x 400)
20 x 16 (500 x 400)
10 x 20 (250 x 500)
12 x 20 (250 x 500)
16 x 20 (400 x 500)
20 x 20 (500 x 500)
25 x 20 (625 x 500)
16 x 25 (400 x 625)
25 x 16 (625 x 400)
20 x 25 (500 x 625)
hEIGht & wIDth
SIZE: INChES (mm)
10 x 16 (250 x 400)
12 x 16 (300 x 400)
16 x 16 (400 x 400)
20 x 16 (500 x 400)
10 x 20 (250 x 500)
12 x 20 (300 x 500)
16 x 20 (400 x 500)
20 x 20 (500 x 500)
25 x 20 (625 x 500)
16 x 25 (400 x 625)
25 x 16 (625 x 400)
20 x 25 (500 x 625)
hEIGht & wIDth
www.chgusa.com
NOtE: FIRSt twO NUMBERS OF SIZE INDICAtE VERtICAL hEIGht. SECOND twO NUMBERS REpRESENt hORIZONtAL wIDth, BOth ARE NOMINAL DIMENSIONS. ACtUAL SIZE OF FILtERS ARE 7/16”(11mm) LESS thAN NOMINAL. NOMINAL thICKNESS IS 2” (50mm). ACtUAL thICKNESS IS 1-3/4”(44mm). StANDARD pACKAGE CONSIStS OF SIX FILtERS.
BAFFLE TYPE
GREASE FILTERAIR FLOW CHARACTERISTICS
Series FA30, FG35, FS50
CFM VS STATIC PRESSURE
FLOW RATE
CFM(m3/min)
200 (5.6)
250 (7.0)
300 (8.5)
400 (11.3)
450 (12.7)
500 (14.1)
550 (15.6)
600 (17.0)
650 (18.4)
700 (19.8)
750 (21.2)
800 (22.6)
850 (24.0)
900 (25.5)
950 (26.9)
1000 (28.3)
10 x 20 12 x 16 12 x 20 16 x 16 16 x 20 20 x 20 16 x 25 20 x 25(250 x 500) (300 x 400) (300 x 500) (400 x 400) (400 x 500) (500 x 500) (400 x 625) (500 x 625)
0.13 0.15 0.10 0.07 0.04 0.04 0.04 0.03
0..27 0.31 0.22 0.16 0.09 0.08 0.09 0.05
0.39 0.45 0.31 0.23 0.12 0.13 0.12 0.08
0.7 0.8 0.54 0.41 0.23 0.21 0.23 0.15
0.89 1.01 0.69 0.51 0.28 0.25 0.28 0.19
1.1 1.26 0.85 0.62 0.35 0.32 0.35 0.24
1.33 1.52 1.03 0.76 0.43 0.39 0.42 0.28
1.58 1.22 0.91 0.51 0.46 0.51 0.34
1.44 1.07 0.61 0.52 0.61 0.41
1.23 0.7 0.61 0.69 0.47
1.42 0.8 0.7 0.8 0.54
0.92 0.8 0.91 0.61
1.03 0.89 1.01 0.69
1.15 0.99 1.15 0.77
1.29 1.11 1.27 0.87
1.42 1.24 1.41 0.96
EFFECTIVE AREATHE EFFECTIVE AREA FOR NOMINAL SIZE FILTERS ARE AS LISTED
FILTER SIZE: HEIGHT x WIDTH EFFECTIVE AREA
INCHES (MILLIMETERS) SqUARE FEET (Sq. METERS)
10” x 20” (250 x 500)
12” x 16” (300 x 400)
12” x 20” (300 x 500)
16” x 16” (400 x 400)
16” x 20” (400 x 500)
20” x 20” (500 x 500)
16” x 25” (400 x 625)
20” x 25” (500 x 625)
1.00 (0.9)
0.97 (.09)
1.25 (.11)
1.36 (.12)
1.75 (.16)
2.25 (.20)
2.24 (.20)
2.88 (.26)
D9
air flow characteristics
STATIC PRESSURE
FILTER SIZE: INCHES x INCHES (mm x mm)
800-526-3694
MESH TYPE
AIR FILTERSStandard Commercial Sizes Available in...
ALUMINUM FRAMED MODELS and
GALVANIZED STEEL FRAMED MODELS
n RIGID HEAVY DUTY CONSTRUCTION n BEST PRICING n CORROSION RESISTANT
n ALL STEEL WIRE MESH DESIGN FOR MAXIMUM CAPTURE OF DUST AND GREASE
ACCEptED FOR USE By thE CIty OF NEw yORK DEpARtMENt OF BUILDING MEA #57-82M
NOtE: StANDARD pACKAGE CONSIStS OF SIX FILtERS. NOMINAL thICKNESS IS 2”(50mm)...ACtUAL thICKNESS IS 1-3/4”(45mm). ACtUAL hEIGht AND wIDth ARE7/16”(11mm) LESS thAN NOMINAL SIZES LIStED. SpECIAL SIZE FILtERS AND1”(25mm) FILtERS ARE FURNIShED wIthOUt hANDLES LIFt hANDLES AREAVAILABLE ON AppLICAtION. ALL StAINLESS StEEL (FRAME AND MEDIA) MODELSAVAILABLE ON AppLICAtION.
HEIGHT & WIDTH
SIZE: INCHES (mm)
10 x 20 (250 x 500)
16 x 20 (400 x 500)
16 x 25 (400 x 625)
20 x 20 (500 x 500)
20 x 25 (500 x 625)
ALUMINUM FRAMED
MODEL NO. PACKAGE WGT:
LBS. (kg)
F40-1020 11 (5)
F40-1620 18 (8)
F40-1625 22 (10)
F40-2020 22 (10)
F40-2025 26 (12)
GALVANIZED STEEL FRAMED
MODEL NO. PACKAGE WGT:
LBS. (kg)
F41-1020 14 (6)
F41-1620 23 (10)
F41-1625 28(13)
F41-2020 28 (13)
F41-2025 33 (12)
MESH TYPE AIR FILTERS
air filters
D10
OPTIONAL SNAP-ON
HANDLES AVAILABLE
(FURNISHED IN PAIRS)
SPECIFY...
MODEL NO. F41-0001
NET FACE VELOCITY
FPM
267356445533622711800
RESISTANCE IN INCHES OF W.G.
NOMINAL THICKNESS
1 INCH 2 INCH
AIR DELIVERY DATA CHART
.025
.040067.100.142------
.020
.038
.060
.090
.129
.169
.218
CFMCAPACITY BY SIZE
16x20 16x25 20x20 20x25
467623779933108912441400
5977969951192139115901789
60080010001200140016001800
768102412791532178820442300
Filters shall retain 290 grams of dust per 2.25sf (20x20 filter). Resistance whenclean is 0.05w.g. at FpM air velocity. Maximum resistance at capacity is .335w.g.
www.chgusa.com
REF. A
5/16”(8mm)
1-3/8”(35mm)
1/2”(13mm) 7/32”
(5.5mm)
STAINLESS STEEL
CAP STRIPFOR 1/16”(1.5mm) MAtERIAL
MODEL NO. J63-1451
7 Ft. (2130mm) LENGth
MODEL NO. J63-1451-8*
8 Ft. (2440mm) LENGth
MODEL NO. J63-1451-9*
9 Ft. (2745mm) LENGth
MODEL NO. J63-1451-10*
10 Ft. (3050mm) LENGth
BRIGht FINISh
REF. B
7/8”(22mm)
* AVAILABLE ON AppLICAtIONAND 12 pIECE MINIMUM FOR
8,9 & 10 Ft LENGthS
STAINLESS STEEL
DIVIDER BARWITH GALVANIZED BACK PLATE
FOR 1/16”(1.5mm) MAtERIAL
MODEL NO. J64-1450
7 Ft. (2130mm) LENGth
MODEL NO. J64-1450-8*
8 Ft. (2440mm) LENGth
MODEL NO. J64-1450-9*
9 Ft. (2745mm) LENGth
MODEL NO. J64-1450-10*
10 Ft. (3050mm) LENGth
BRIGht FINISh
REF. C
EXTENDED LENGTH
STAINLESS STEEL
CAP STRIPFOR 1/16”(1.5mm) MAtERIAL
MODEL NO. J63-1651-78
6.5 Ft. (1980mm) LENGth
MODEL NO. J63-1651-120
10 Ft. (3050mm) LENGth
SAtIN FINISh
EXTENDED LENGTH
STAINLESS STEEL
DIVIDER BARWITH SS BACK PLATE
FOR 1/16”(1.5mm) MAtERIAL
MODEL NO. J64-1651-78
6.5 Ft. (1980mm) LENGth
MODEL NO. J64-1651-120
10 Ft. (3050mm) LENGth
SAtIN FINISh
REF. D
2-5/32”(54.5mm)
7/8”(22mm)
7/16”(11mm)
7/8”(22mm)
1-1/2”(38mm)
A
B
C
D
TM
TM
MOULDINGS AND DIVIDERS
* AVAILABLE ON AppLICAtIONAND 12 pIECE MINIMUM FOR
8,9 & 10 Ft LENGthS
REMOVABLE STAINLESS STEEL
CANOPY HOOD GREASE CUPSn CONFORMS TO N.F.P.A. REqUIREMENTS
n TYPE 304 STAINLESS STEEL
D11
Stainless Steel
KEYHOLE WELD STUDS
MODEL NO.q37-0250
SEE DEtAILS FOR SIZE
COMpONENt
canopy hood grease cups
KEYHOLE MOUNT CUP
MODEL NO. F15-4000Size: 4” x 6-5/8” x 4” DEEp
(100mm x 168mm x 100mm)
KEYHOLE MOUNT CUP
MODEL NO. F15-2500Size: 4” x 6-5/8” x 2-1/2” DEEp
(100mm x 168mm x 63mm)
SIDE MOUNT CUP
MODEL NO. F15-0019Size: 4-1/4” x 6-3/4” x 2-1/2” DEEp
(110mm x 171mm x 63mm)
1/9 pAN EqUIVALENt ON ALL MODELS
REF. B
REF. A
REF. A REF. B REF. C
REF. C
n DESIGNED FOR DRAINING GREASE FROM TROUGHTO GREASE CUP
n SUPPLIED WITH LOCKNUT AND WASHER
n FITS 1/2”(13mm) I.D. HOSE OR 3/8”(9.5mm)O.D. TUBING
Nickel Plated Brass
CANOPY HOOD DRAINMODEL NO. F10-1187
2-1/2”(63mm)
6-5/8”(168mm)
4”(100mm)
4”(100mm)
4”(100mm)
4”(100mm)
4”(100mm)
6-5/8”(168mm)
4-1/4”(108mm)
6-3/4”(171mm)
2-1/2”(63mm)
1/2” (13mm) O.D.
.282.030
.025 DIA. .6mm DIA.
6mmDIA.
3mm
11mm
.125
.430
.8mm7mm
.250DIA.
3/8” (10mm) I.D.
1” (25mm) DIA.
1/2” NPS
9/16”(14mm)
1/16”(1.6 mm)
15/16”(24mm)
800-526-3694
KEYHOLE MOUNT CUP
MODEL NO. F15-2500-CSize: 4” x 6-3/4” x 2-1/2” DEEp
(100mm x 171mm x 63mm)
REF. D
4”(100mm)
2-1/2”(63mm)
6-3/4”(171mm)4”
(100mm)
REF. D
10° Mounting
B
D
C
F
E
NEW
FEATURE!
A
G H
D12
E-Z MOUNT
CANOPY LIGHTING FIXTURES FOR COMMERCIAL COOKING HOODS
SPECIFICATIONSFIXTURE BODY: Die cast aluminum with brushed finish
SOCKET: porcelain body with copper shellWIRE LEADS: 16 AwG, 6”(150mm) long
GROUND LEAD: 6”(150mm) long green colored 18 AwG wireWATTAGE: Accepts standard 100 watt A19 bulb (not furnished).VOLTAGE: Rated up to 120 voltsGASKETS: Silicone
GLOBE: Silicone* or clear, thermal and shock resistant tempered glass
WIRE GUARD: plated steelOVERALL SIZE: 5-1/2”(140mm) diameter
8-3/4”(220mm) long with wire guardJUNCTION BOX: Not furnished. Fixture is designed to accept any
standard 1/2”(90mm) or 4”(100mm) junction box
E-Z MOUNT CANOPY LIGHTING FIXTURES U.L. MODEL NO. CSA MODEL NO. DESCRIPTION
A L55-1004 L55-1004-CSA FURNIShED wIth tUFF-SKIN COAtED**
*L55-1004-HT thERMAL AND ShOCK RESIStANt tEMpERED GLASS GLOBE
B L55-1024 L55-1024-CSA FURNIShED wIth tUFF-SKIN COAtED**
*L55-1024-HT thERMAL AND ShOCK RESIStANt tEMpERED GLASS GLOBE AND wIRE GUARD
C L55-2004 L55-2004-CSA FURNIShED wIth thERMAL, ShOCK
*L55-2004-HT RESIStANt tEMpERED GLASS GLOBE
D L55-2024 L55-2024-CSA FURNIShED wIth thERMAL, ShOCK
*L55-2004-HT RESIStANt tEMpERED GLASS GLOBEAND wIRE GUARD
LIStED FILE #E80045
COMpONENt
CERtIFIEDFILE #LR63261
n E-Z MOUNt FEAtURE ALLOwS FOR qUICK INStALLAtION
n GASKEtS pERMANENtLy AFFIXED SAVE INStALLAtION tIME
n U.L. LIStED AND C.S.A. CERtIFIED FOR USE IN COMMERCIAL COOKING hOODS
n MEEtS ALL REqUIREMENtS FOR N.F.p.A. AND N.E.C. 410
n DESIGNED FOR CONVENIENt INStALLAtION tO pREwIRED hOODS
n GREASEpROOF, wAtERpROOF AND hEAtpROOF CONStRUCtION
n ALUMINUM FIXtURES ARE FURNIShED wIth A BRUShED FINISh tO MAtCh StAINLESS StEEL hOOD INtERIORS
E-Z mount incandescent canopy lighting fixtures
B A
D C
www.chgusa.com
*AVAILABLE AS HIGH TEMP MODELS RATED TO 392˚F (200˚C), 600V, LEADS: 14 AWG, 6” LONGSTRIPPED END. INSULATION: SILICONE RUBBER WITH TREATED GLASS BEAD SLEEVING REF. DESC. MODEL NO.
A GLOBE, tEMpERED GLASS L55-X022thermal and Shock Resistant
B wIRE GUARD L10-X020
C LAMp hOUSING ASSEMBLyComplete with porcelain Socket L55-Y001and required Silicone Gasket *L55-Y001-HT
D SCREw L55-X006
E ADAptER pLAtE L50-X009
F pORCELAIN SOCKEt L55-X003*L55-X003-HT
G GLOBE, tEMpERED GLASSSilicone Coated, thermal and Shock Resistant L50-X011
h GASKEt SEt L50-Y001
L55 SERIES LIGHTING FIXTUREREPLACEMENT PARTS
NOtE: **SILICONE COAtED GLOBES pROVIDED wIth “TUFF-SKIN” COAtING whICh ELIMINAtES hOt SpOt BROwNING / DISCOLORAtION
OF GLOBE...pREVENtS GLASS ShAttER FROM IMpACt, DROppING, UNUSUAL
StRESSES AND thERMAL ShOCK. SCRAtCh RESIStANt...U.S.D.A. AppROVED...
IMpROVES LIGht SOURCE By pROVIDING BEttER DIFFUSION.
UNDERWRITERS LABORATORIES STANDARD #1571 REQUIRES THAT FIXTURESIN COMMERCIAL COOKING HOODS MUST BE MOUNTED A MINIMUM OF 4 FEET
(1200mm) ABOVE THE COOKING SURFACE.
*AVAILABLE AS HIGH TEMP MODELS RATED TO 392˚F (200˚C), 600V, LEADS: 14 AWG, 6” LONG STRIPPED END. INSULATION: SILICONE RUBBER WITH TREATED GLASS BEAD SLEEVING
D13
RECESSED FLUORESCENT...LOW PROFILEn NSF LIStED, UL LIStED E250943 FOR USE IN COMMERCIAL
COOKING hOODSn MEEtS ALL REqUIREMENtS FOR N.F.p.A. AND N.E.C. 410n ONLy 4-1/2” (115mm) hIGh...FOR LIMItED OVERhEAD
CLEARANCE AppLICAtIONSn tEMpERED, pRISMAtIC GLASS DIFFUSER wIth ONE pIECE
SAtIN FINIShED StAINLESS StEEL FACE FRAME tO MAtCh hOOD INtERIOR
SPECIFICATIONSBALLAST: Universal 120-277v, 50 or 60 hz, t8, UL ListedLAMPS: t8 Fluorescent lamps (not furnished) BODY: Steel with baked white enamel finish MOUNTING: #10-32 x 3/4” (20 mm) long threaded studsREFLECTOR: Baked white enamel finish...providing a minimum of 87% diffused reflection DIFFUSER: Crystal 73 tempered prismatic glass with prisms on inside of fixture, mountedinto a stainless steel face frame with special sealing gasketing. Secured to fixture body withstainless steel screws for easy servicing.
RECESSED FLUORESCENT CANOPY HOOD LIGHT FIXTURES
MODEL NO.
L82-1020
L82-1030
L82-1040
LAMPSREQUIRED
(2) F17T8
(2)F25T8
(2) F32T8
HOLESREQ’D
12
14
14
OVERALLTRIM SIZE
10-1/4” X 26-1/4”(260mm x 660mm)
10-1/4” X 38-1/4”(260mm x 970mm)
10-1/4 ” X 50-1/4”(267mm x1270mm)
“A”DIM.
6” (150mm)
7-1/2”(190mm)
10-1/2”(265mm)
CUT-OUTSIZE
8-1/2” X 24-1/2”(215mm x620mm)
8-1/2” X 36-1/2”(215mm x 930mm)
8-1/2” X 48-1/2”(215mm x 1230mm)
8” (200mm)
4-1/2”(115mm)
10-1/4” (260mm)
SECTIONMOUNTING CUT-OUT DIAGRAM
3-1/4”(82mm)
3-1/4”(82mm)
9-3/16”(233mm)
1/4”(6mm) DIA. hOLES
CUt-OUt
A A A A
CANOPY HOOD LIGHT FIXTURES
SPECIFICATIONSSOCKET: Side mounted porcelain medium base
WATTAGE: Accepts standard 150 watt A23 bulb maximum(not furnished)VOLTAGE: Rated up to 120 Volts
DIFFUSER: Crystal 73 tempered prismatic glass with prisms on inside of fixtureFACEPLATE: One piece, stainless steel with smooth satin finish
LOCKUP: (4) captive stainless steel screwsRETAINER: twin spring and cable for faceplate and frame
REFLECTOR: Die formed aluminum with satin finishWIRING: Connections to socket are made in the interior
removable thermal insulated wiring chamberBODY: Steel recessed housing with baked white enamel finish
MOUNTING: (4) #10-24 x 3/4” (20mm) long threaded studs
RECESSED INCANDESCENT
n UL LIStED E253411 AND CERtIFIED FOR CANADA FOR USE IN COMMERCIAL COOKING hOODS
n MEEtS ALL REqUIREMENtS FOR NFpA AND NEC 410 n NSF LIStINGn SAtIN FINIShED StAINLESS StEEL FACEpLAtE
tO MAtCh hOOD INtERIORSn tEMpERED, pRISMAtIC GLASS DIFFUSER
RECESSED INCANDESCENT CANOPY HOOD LIGHT FIXTURE
MODEL NO. L87-1004
CUT-OUTMOUNTING DIAGRAM
12-7/8”(327mm)
12-7/8”(327mm)
12” (305mm)
12” (305mm)
1/4” (6mm)DIA. hOLES
SECTION
11-1/2” (240mm) Sq.
14” (350mm) Sq. FACEpLAtE
6”(150mm)
COMpONENt
800-526-3694
recessed canopy light fixtures
multi-valve dampers, access doors
SINGLE DEFLECTION
MULTI-VALVE DAMPERSn EXTRUDED ANODIZED ALUMINUM TO MATCH
STAINLESS STEEL
n AERODYNAMIC FIN DESIGN
90 VML SERIES SINGLE DEFLECTION
MULTI-VALVE DAMPERS
DUCT SIZE (ACTUAL HOLE SIZE)
20” x 4” (500mm x 100mm)
20” x 6” (500mm x 150mm)
24” x 4” (600mm x 100mm)
24” x 6” (600mm x 150mm)
24” x 8” (600mm x 200mm)
24” x 10” (600mm x 250mm)
24” x 12” (600mm x 300mm)
30” x 6” (750mm x 150mm)
36” x 6” (900mm x 150mm)
ALL MODELS LISTED ARE STOCKED AND READY FORIMMEDIATE SHIPMENT.
OTHER SIZES AVAILABLE UPON APPLICATIONHORIZONTAL DAMPERS AVAILABLE ON
SPECIAL APPLICATION. (ON SPECIAL APPLICATION ORDERS ALLOW TWO WEEKS FOR
DELIVERY FROM RECEIPT OF ORDER)
FOR OVERALL DIMENSIONS ADD 1-3/4”(45mm) TO LISTEDWIDTH AND LENGTH.
MODEL NO.
90VML-20X4
90VML-20X6
90VML-24X4
90VML-24X6
90VML-24X8
90VML-24X10
90VML-24X12
90VML-30X6
90VML-36X6
D14
n hI-tEMp ACCESS DOOR IS SOLID, LEAK RESIStANt ANDCONSIStS OF twO LAyERS OF StAMpED, hOt DIppEDGALVANIZED StEEL AND ONE 16 GAUGE BLACK IRONBACKING pLAtE.
n hI-tEMpERAtURE CERAMIC FIBER GASKEt (2300°F, 1260°C MAX-MEEtS NFpA 96 StANDARDS) IS pERMANENtLy BONDED tO thE OUtSIDE pANEL OF thEACCESS DOOR tO ELIMINAtE LEAKAGE.
n ZINC pLAtED CONICAL SpRINGS ARE INStALLED,BEtwEEN thE INNER AND OUtER pLAtES, tO FACILItAtE OpENING.
n ZINC COAtED wING NUtS ARE EASILy tURNED By hAND.
n NO MEASURING (SELF-ADhESIVE tEMpLAtE pROVIDED)
HI-TEMP ACCESS DOORS
ACCESS DOORS
MODEL NO.
ACC-10X6
ACC-12X8
ACC-18X14
DISCRIPTION
ACCESS pANEL 10” X 6” ACCESS pANEL 12” X 8”ACCESS pANEL 18” X 14”
ACCESS DOORS WITH 6” MOUNTING STUDS
MODEL NO.
ACC-10X6-6
ACC-12X8-6
DISCRIPTION
ACCESS pANEL 10” X 6” w/6” LONG StUDSACCESS pANEL 12” X 8” w/6” LONG StUDS
Q ALSO AVAILABLE WITH6” MOUNTING STUDS
www.chgusa.com
D15
curved & flat access doors – UL Fire Rated
800-526-3694
GH
E
CD
BA
F
Door
Gasket
BackFrame
NOTE: Gasket is High Temp bonded to front panel
Optional 4”(100mm) studs for zero clearance duct wrapOrder with suffi x (-4)
E-Clip holds back frame to duct for each stud
E-Clip
Wing Nuts
Please Order by Part No.
BACK FRAME OUTSIDE DIMENSION
FRONT PANELOUTSIDE DIMENSION
PANEL WIDTH
STUD HEIGHT
HOLE SIZE • BACK FRAME INSIDE DIMENSION
MOUNTINGSTUDS
PART NO. A* B* C D E F G H750710 7” 10” 7” 10” Flat 1” 5.5” 8.5” 6750715 7” 15’ 7” 15” Flat 1” 5.5” 13.5” 6750723 7” 23” 7” 23” Flat 1” 5.5” 21.5” 10750606 8” 8” 8” 8” Flat 1” 6” 6” 4750707 10” 10” 10” 10” .5” 1” 7” 7” 4750712 10” 15” 10” 15” .5” 1” 7” 12” 6750720 10” 23” 10” 23” .5” 1” 7” 20” 10751212 15” 15” 15” 15” .5” 1” 12” 12” 8751220 15” 23” 15” 23” .5” 1” 12” 20” 14751620 19” 23” 19” 23” .5” 1” 16” 20” 16752020 23” 23” 23” 23” .5” 1” 20” 20” 16
CURVED ACCESS DOORS
FLAT ACCESS DOORS
CURVED & FLAT ACCESS DOORS
n HEAVY-DUTY 16 GAUGE STEEL CONSTRUCTION
n GASKET RATED TO 2300 ºF FOR FIRE TIGHT SEAL
n BACK FRAME REINFORCES DUCT CUT-OUT
n AVAILABLE WITH EXTENDED STUDS TO ACCOMMODATE
FIRE WRAP FOR CURVED AND FLAT DUCT APPLICATIONS
n STANDARD AND CUSTOM SIZES AVAILABLE
n EASY TO INSTALL
n EASY TO CLEAN
For more information on Flame Gard products visit our website at www.flamegardusa.com
A
B
D
Access Panel
Gasket(Permanently attached to
Access Panel)Access Frame(Mounted on
inside of Duct)
E-Clip
Weld Nuts
Weld Nuts
Reverse view of Access Frame
Stud in Center of Radius
Wing Nuts
Wing Screws
G
H
C
*The outside dimension C should be 70% or less than the Duct Diameter for proper fi t.
Please Order by Part No. OUTSIDE DIMENSIONS HOLE SIZE INSIDE
DIMENSIONSPART NO. A* B* C D G H750505-C 6.56” 6.75” 6.56” 6.75” 5.06” 5.25”750511-C 6.50” 12.75” 6.50” 12.75” 5.00” 11.25”750517-C 6.50” 18.75” 6.50” 18.75” 5.00” 17.25”750808-C 9.50” 9.75” 9.50” 9.75” 8.00” 8.25”750811-C 9.50” 12.75” 9.50” 12.75” 8.00” 11.25”750817-C 9.50” 18.75” 9.50” 18.75” 8.00” 17.25”750823-C 9.50” 24.75” 9.50” 24.75” 8.00” 23.25”751117-C 12.50” 18.75” 12.50” 18.75” 11.00” 17.25”751123-C 12.50” 24.75” 12.50” 24.75” 11.00” 23.25”751717-C 18.50” 18.75” 18.50” 18.75” 17.00” 17.25”751723-C 18.50” 24.75” 18.50” 24.75” 17.00” 23.25”
Note: Optional 4”(100mm) Long Studs ForFire Wrap Insulation. Order with suffix (-4)
HOOD AND DUCT Accessory
65X3
FILE# MH16475NFPA #96
HOOD AND DUCT Accessory
65X3
FILE# MH16475NFPA #96
www.chgusa.comD16
FOIL and DUCT TAPE
INSULATION HANGERSn PROVIDED WITH PEEL AND PLACE ADHESIVE BACKING
n ELIMINATES USING CAPACITOR DISCHARGE NAILS
Insulation hangers are made of 2” x 2” (50mm x 50mm) Galvanized plates with a 1/32”(.794mm) white urethane foam backing which has been coated with a high performance, acrylic based adhesive protected by a release coated liner.
INSULATION HANGERS
HANGER LENGTH
1” (25mm)
1-1/4” (32mm)
1-1/2” (38mm)
1-5/8” (42mm)
2” (50mm)
MODEL NO.
q86-1000
q86-1250
q86-1500
q86-1625
q86-2000
NOtE: OthER LENGthS AVAILABLE UpON REqUESt
INSULATION WELD PINS
SILICONE SEALANTn NSF LISTEDn AVAILABLE IN CLEAR, BRIGHT ALUMINUM,
WHITE, BLACK AND RED (HI-TEMP)n FITS ALL STANDARD CAULKING GUNSn FDA APPROVED n U.L. RECOGNIZEDn MEETS FDA EXTRACTION REqUIREMENT
NO. 21 CFR177.2600
SILICONE SEALANT 10.3 oz. (305ml) CARTRIDGE
COLOR MAX. SERVICE MODEL NO.
CLEAR 400°F (232°C) M90-1010
ALUMINUM 400°F (232°C) M90-1012
whItE 400°F (232°C) M90-1014
BLACK 400°F (232°C) M90-1016
hI tEMp RED 500°F (315°C) M90-1018
FURNIShED wIth REMOVABLE tIp - pACKAGED 10 pER pACK
ALSO AVAILABLE IN 3 OZ. (83g) TUBES
CLEAR: M90-0310 ALUMINUM: M90-0312 WHITE: M90-0314pACKAGED 20 pER pACK
5 GALLON (19 liter): MODEL NO. M90-5012
PIN SIZE
12 GA. x 1” (25mm)
12 GA. x 1-1/2”(38mm)
12 GA. x 2”(50mm)
MODEL NO.
q86-0010
q86-0015
q86-0020
HEAVY DUTY DUCT TAPE
2” wIDE x 60 yDS. (50mm x 55m)
MODEL NO. q84-3200
HIGH STRENGTH ALUMINUM FOIL TAPE
2-1/2” wIDE x 50 yDS. (65mm x 45m)
MODEL NO. q84-4250
insulation hangers, sealant & tape
201016 . . . . . . . . . . . . . . . . . . . . . . .D5201020 . . . . . . . . . . . . . . . . . . . . . . .D5201216 . . . . . . . . . . . . . . . . . . . . . . .D5201220 . . . . . . . . . . . . . . . . . . . . . . .D5201616 . . . . . . . . . . . . . . . . . . . . . . .D5201620 . . . . . . . . . . . . . . . . . . . . . . .D5201625 . . . . . . . . . . . . . . . . . . . . . . .D5202016 . . . . . . . . . . . . . . . . . . . . . . .D5202020 . . . . . . . . . . . . . . . . . . . . . . .D5202025 . . . . . . . . . . . . . . . . . . . . . . .D5202516 . . . . . . . . . . . . . . . . . . . . . . .D52025 20 . . . . . . . . . . . . . . . . . . . . . . .D5750505-C . . . . . . . . . . . . . . . . . . . .D15750511-C . . . . . . . . . . . . . . . . . . . .D15750517-C . . . . . . . . . . . . . . . . . . . .D15750606 . . . . . . . . . . . . . . . . . . . . . .D15750707 . . . . . . . . . . . . . . . . . . . . . .D15750710 . . . . . . . . . . . . . . . . . . . . . .D15750712 . . . . . . . . . . . . . . . . . . . . . .D15750715 . . . . . . . . . . . . . . . . . . . . . .D15750720 . . . . . . . . . . . . . . . . . . . . . .D15750723 . . . . . . . . . . . . . . . . . . . . . .D15750808-C . . . . . . . . . . . . . . . . . . . .D15750811-C . . . . . . . . . . . . . . . . . . . .D15750817-C . . . . . . . . . . . . . . . . . . . .D15750823-C . . . . . . . . . . . . . . . . . . . .D15751117-C . . . . . . . . . . . . . . . . . . . .D15751123-C . . . . . . . . . . . . . . . . . . . .D15751212 . . . . . . . . . . . . . . . . . . . . . .D15751220 . . . . . . . . . . . . . . . . . . . . . .D15751620 . . . . . . . . . . . . . . . . . . . . . .D15751717-C . . . . . . . . . . . . . . . . . . . .D15751723-C . . . . . . . . . . . . . . . . . . . .D15752020 . . . . . . . . . . . . . . . . . . . . . .D1590VML-20X4 . . . . . . . . . . . . . . . . .D1490VML-20X6 . . . . . . . . . . . . . . . . .D1490VML-24X10 . . . . . . . . . . . . . . . .D1490VML-24X12 . . . . . . . . . . . . . . . .D1490VML-24X4 . . . . . . . . . . . . . . . . .D1490VML-24X6 . . . . . . . . . . . . . . . . .D1490VML-24X8 . . . . . . . . . . . . . . . . .D1490VML-30X6 . . . . . . . . . . . . . . . . .D1490VML-36X6 . . . . . . . . . . . . . . . . .D14ACC-10X6 . . . . . . . . . . . . . . . . . . .D14ACC-12X8 . . . . . . . . . . . . . . . . . . .D14ACC-18X14 . . . . . . . . . . . . . . . . . .D14ACC-10X6-6 . . . . . . . . . . . . . . . . .D14ACC-12X8-6 . . . . . . . . . . . . . . . . .D14F10-1187 . . . . . . . . . . . . . . . . . . . .D11F15-0019 . . . . . . . . . . . . . . . . . . . .D11F15-2500 . . . . . . . . . . . . . . . . . . . .D11F15-2500-C . . . . . . . . . . . . . . . . . .D11F15-4000 . . . . . . . . . . . . . . . . . . . .D11FA30-1016-hD . . . . . . . . . . . . . . . . .D8FA30-1020-hD . . . . . . . . . . . . . . . . .D8FA30-1216-hD . . . . . . . . . . . . . . . . .D8FA30-1220-hD . . . . . . . . . . . . . . . . .D8FA30-1616-hD . . . . . . . . . . . . . . . . .D8FA30-1620-hD . . . . . . . . . . . . . . . . .D8FA30-1625-hD . . . . . . . . . . . . . . . . .D8FA30-2016-hD . . . . . . . . . . . . . . . . .D8FA30-2020-hD . . . . . . . . . . . . . . . . .D8FA30-2025-hD . . . . . . . . . . . . . . . . .D8FA30-2520-hD . . . . . . . . . . . . . . . . .D8FG35-1016-hD . . . . . . . . . . . . . . . .D8FG35-1020-hD . . . . . . . . . . . . . . . .D8FG35-1216-hD . . . . . . . . . . . . . . . .D8FG35-1220-hD . . . . . . . . . . . . . . . .D8
FG35-1616-hD . . . . . . . . . . . . . . . .D8FG35-1620-hD . . . . . . . . . . . . . . . .D8FG35-1625-hD . . . . . . . . . . . . . . . .D8FG35-2016-hD . . . . . . . . . . . . . . . .D8FG35-2020-hD . . . . . . . . . . . . . . . .D8FG35-2025-hD . . . . . . . . . . . . . . . .D8FG35-2516-hD . . . . . . . . . . . . . . . .D8FG35-2520-hD . . . . . . . . . . . . . . . .D8F40-0002 . . . . . . . . . . . . . . . . . . . .D10F40-1020 . . . . . . . . . . . . . . . . . . . .D10F40-1620 . . . . . . . . . . . . . . . . . . . .D10F40-1625 . . . . . . . . . . . . . . . . . . . .D10F40-2020 . . . . . . . . . . . . . . . . . . . .D10F40-2025 . . . . . . . . . . . . . . . . . . . .D10F41-0001 . . . . . . . . . . . . . . . . . . . .D10F41-1020 . . . . . . . . . . . . . . . . . . . .D10F41-1620 . . . . . . . . . . . . . . . . . . . .D10F41-1625 . . . . . . . . . . . . . . . . . . . .D10F41-2020 . . . . . . . . . . . . . . . . . . . .D10F41-2025 . . . . . . . . . . . . . . . . . . . .D10FS50-1016-BA . . . . . . . . . . . . . . . . .D8FS50-1020-BA . . . . . . . . . . . . . . . . .D8FS50-1216-BA . . . . . . . . . . . . . . . . .D8FS50-1220-BA . . . . . . . . . . . . . . . . .D8FS50-1616-BA . . . . . . . . . . . . . . . . .D8FS50-1620-BA . . . . . . . . . . . . . . . . .D8FS50-1625-BA . . . . . . . . . . . . . . . . .D8FS50-2016-BA . . . . . . . . . . . . . . . . .D8FS50-2020-BA . . . . . . . . . . . . . . . . .D8FS50-2025-BA . . . . . . . . . . . . . . . . .D8FS50-2516-BA . . . . . . . . . . . . . . . . .D8FS50-2520-BA . . . . . . . . . . . . . . . . .D8J63-1451 . . . . . . . . . . . . . . . . . . . .D10J63-1451-8 . . . . . . . . . . . . . . . . . .D10J63-1451-9 . . . . . . . . . . . . . . . . . .D10J63-1451-10 . . . . . . . . . . . . . . . . .D10J63-1651-78 . . . . . . . . . . . . . . . . .D10J63-1651-120 . . . . . . . . . . . . . . . .D10J64-1450 . . . . . . . . . . . . . . . . . . . .D10J64-1450-8 . . . . . . . . . . . . . . . . . .D10J64-1450-9 . . . . . . . . . . . . . . . . . .D10J64-1450-10 . . . . . . . . . . . . . . . . .D10J64-1651-78 . . . . . . . . . . . . . . . . .D10J64-1651-120 . . . . . . . . . . . . . . . .D10L10-X020 . . . . . . . . . . . . . . . . . . . .D12L50-X009 . . . . . . . . . . . . . . . . . . . .D12L50-X011 . . . . . . . . . . . . . . . . . . . .D12L50-y001 . . . . . . . . . . . . . . . . . . . .D12L55-1004 . . . . . . . . . . . . . . . . . . . .D12L55-1004-CSA . . . . . . . . . . . . . . . .D12L55-1024 . . . . . . . . . . . . . . . . . . . .D12L55-1024-CSA . . . . . . . . . . . . . . . .D12L55-2004 . . . . . . . . . . . . . . . . . . . .D12L55-2004-CSA . . . . . . . . . . . . . . . .D12L55-2024 . . . . . . . . . . . . . . . . . . . .D12L55-2024-CSA . . . . . . . . . . . . . . . .D12L55-X003 . . . . . . . . . . . . . . . . . . . .D12L55-X006 . . . . . . . . . . . . . . . . . . . .D12L55-X022 . . . . . . . . . . . . . . . . . . . .D12L55-y001 . . . . . . . . . . . . . . . . . . . .D12L82-1020 . . . . . . . . . . . . . . . . . . . .D13L82-1030 . . . . . . . . . . . . . . . . . . . .D13L82-1040 . . . . . . . . . . . . . . . . . . . .D13L87-1004 . . . . . . . . . . . . . . . . . . . .D13M90-1010 . . . . . . . . . . . . . . . . . . .D16M90-1012 . . . . . . . . . . . . . . . . . . .D16M90-1014 . . . . . . . . . . . . . . . . . . .D16M90-1016 . . . . . . . . . . . . . . . . . . .D16
NUMERICAL INDEX
MODEL NO. PAGE NO. MODEL NO. PAGE NO.
M90-1018 . . . . . . . . . . . . . . . . . . .D16q37-0250 . . . . . . . . . . . . . . . . . . . .D11q84-3200 . . . . . . . . . . . . . . . . . . . .D16q84-4250 . . . . . . . . . . . . . . . . . . . .D16q86-0010 . . . . . . . . . . . . . . . . . . . .D16q86-0015 . . . . . . . . . . . . . . . . . . . .D16q86-0020 . . . . . . . . . . . . . . . . . . . .D16q86-1000 . . . . . . . . . . . . . . . . . . . .D16q86-1250 . . . . . . . . . . . . . . . . . . . .D16q86-1500 . . . . . . . . . . . . . . . . . . . .D16q86-1625 . . . . . . . . . . . . . . . . . . . .D16q86-2000 . . . . . . . . . . . . . . . . . . . .D16
MODEL NO. PAGE NO.
CANOPY HOODACCESSORIES
1890 SwarthmoreAvenue, PO Box 2020 Lakewood, NJ 08701tel.800-526-3694, 732-363-4700, fax.732-364-8110
www.chgusa.com