CARPENTRY & JOINERY Hammers The tool used for assembling and striking wooden handle chisel is called a mallet. The Warington hammer is used for general bench work. Click arrow to go forward
CARPENTRY & JOINERY Hammers The tool used for assembling and striking wooden handle chisel is called a mallet. The Warington hammer is used for general.
Mar 31, 2015
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
CARPENTRY & JOINERYHammers
CARPENTRY & JOINERYHammers
The tool used for assembling and striking wooden handle chisel is called a mallet.
The Warington hammer is used for general bench work.
Click arrow to go forward
HammersHammers
The claw hammer is used to drive in and withdraw nails
Dovetail saws are used to produce a fine cut, for example when forming dovetail joints.
Click arrow to go forward
ChiselsChisels
The bevel-edge chisel is used for paring joints especially dove-tail joints.
Firmer chisel is used for general purpose chiselling.
Click arrow to go forward
ChiselsChisels
Firmer chisel is used for general purpose chiselling.
A mortise chisel is used to form mortises for tenon joints .
Click arrow to go forward
SawsSaws
The coping saw is used to cut small curves in thin wood or sheets.
Panel saws are used to cut timber sheet materials leaving a fine cut. There are two other saws that look similar, Cross-cut & Rip saw.
Click arrow to go forward
SawsSaws
The tenon saw is used for general bench joinery. (cutting tenons etc)
Dovetail saws are used to produce a fine cut, for example when forming dovetail joints.
Click arrow to go forward
SawsSaws
Click arrow to go forward
The next saw is known as a hard-point or through away saw. Used to cut sheet materials and general construction. (joists, partitions)
SquaresSquares
Combination square: used to check and mark 90 and 45 deg angle and is also used as a gauge.
For marking and checking for square use a Try square.
Click arrow to go forward
SquaresSquares
Mitre square: used to check and for marking a 45 deg angle.
For marking and checking angles from 1 to 180 degrees, use a Sliding bevel.
Click arrow to go forward
PlanesPlanes
Smoothing plane: used to remove marks (pencil, machine) from timber, leaving a smooth finish.
To prepare timber to size, the most suitable plane to use is a Sliding bevel.
Click arrow to go forward
PlanesPlanes
Block plane: used to dress end grain and form chamfers.
When forming grooves in timber the hand tool most suitable, is a Plough plane.
Click arrow to go forward
PlanesPlanes
Bull nose plane: used to trim the cheeks of a tenon and dress into corner of stopped rebate.
Shoulder plane, similar to bull nose has the same functions, one exception, better at trimming shoulders to tenon joints.Click arrow to go forward
PlanesPlanes
Side rebate plane: used to widen grooves and trim edges to housings .
Open throat router is used to cut out waste to gauge line to a housing joint..
Click arrow to go forward
Marking toolsMarking tools
Marking gauge: used to mark one gauge line parallel to the grain. (Housing and Halving joints)
Mortise gauge is used to mark two gauge lines parallel to the grain. (Bridles & Mortise and Tenons).
Click arrow to go forward
Marking toolsMarking tools
Cutting gauge: used to mark one gauge line across the grain. (end rebates).
Click arrow to go forward
ScrewdriversScrewdrivers
Pozidrive, Star or Phillips screwdriver used to withdraw and insert pozidrive, star or phillips screws.
Flat or slotted screwdriver is used to withdraw and insert slotted screws.
Click arrow to go forward
Boring toolsBoring tools
Wheel-brace: used with twist drill to bore holes sizes from 1mm to 12mm.
Press Esc to end the show
Related Documents
